International Standards in process
An International Standard is the result of an agreement between the member bodies of ISO. A first important step towards an
International Standard takes the form of a committee draft (CD) - this is circulated for study within an ISO technical committee. When
consensus has been reached within the technical committee, the document is sent to the Central Secretariat for processing as a draft
International Standard (DIS). The DIS requires approval by at least 75 % of the member bodies casting a vote. A confirmation vote is
subsequently carried out on a final draft International Standard (FDIS), the approval criteria remaining the same.
CD registered
Period from 01 February to 28 February 2011
These documents are currently under consideration in the technical committee.
They have been registred at the Central Secretariat.
TC 4
Rolling bearings
ISO 1206:2001/CD Amd 1
Rolling bearings — Needle roller bearings, dimension series 48, 49 and 69 — Boundary dimensions
and tolerances — Amendment 1: Tolerance limits for shaft raceway and housing bore diameters
ISO 3245:2007/CD Amd 1
Rolling bearings — Needle roller bearings, drawn cup without inner ring — Boundary dimensions and
tolerances — Amendment 1: Tolerance limits for shaft raceway and housing bore diameters
TC 8
Ships and marine technology
ISO/DPAS 30004
Ship recycling management systems — Guidelines for implementing ISO 30000
ISO/CD 13073-2
Ships and marine technology — Risk assessment on anti-fouling systems on ships — Part 2: Marine
environmental risk assessment method for anti-fouling systems on ships using biocidally active
substances
ISO/CD 16165
Ships and marine technology — Marine environment protection — Terminology relating to oil spill
response
ISO/CD 16304
Ships and marine technology — Marine environment protection — Arrangement and management of
port waste reception facilities
ISO/CD 16855
Ships and Marine Technology — Loose gear of lifting appliances on ships — General requirements
ISO/CD 16856
Ships and Marine Technology — Loose gear of lifting appliances on ships — Hooks
ISO/CD 16857
Ships and Marine Technology — Loose gear of lifting appliances on ships — Shackles
ISO/CD 16858
Ships and Marine Technology — Loose gear of lifting appliances on ships — Pulleys
TC 22
Road vehicles
ISO/CD 6624-2
Internal combustion engines — Piston rings — Part 2: Half keystone rings made of cast iron
ISO/CD 6624-4
Internal combustion engines — Piston rings — Part 4: Half keystone rings made of steel
ISO/CD 6722-2
Road vehicles - 60 V and 600 V single-core cables — Part 2: Dimensions test methods and
requirements for aluminium conductor cables
TC 30
Measurement of fluid flow in closed conduits
ISO/CD 17089-2
Measurement of fluid flow in closed conduits - Ultrasonic meters for gas — Part 2: Meters for industrial
applications
TC 34
Food products
ISO/CD 14477
Vegetable fats and oils — Determination of triacylglycerols — Method by high performance liquid
chromatography (HPLC)
TC 35
Paints and varnishes
ISO/CD 16474-1
Paints and varnishes — Methods of exposure to laboratory light sources — Part 1: General guidance
ISO/CD 16474-2
Paints and varnishes — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ISO/CD 16474-3
Paints and varnishes — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV
lamps
ISO/CD 16474-4
Paints and varnishes — Methods of exposure to laboratory light sources — Part 4: Carbon-arc lamps
TC 42
Photography
ISO/CD 15781
Photography — Digital cameras — Measuring shooting time lag, shutter release time lag, shooting
rate, and start-up time
TC 45
Rubber and rubber products
ISO/CD 11619
Specification for polyurethane tubing for use primarily in pneumatic installations
ISO/CD 2285
Rubber, vulcanized or thermoplastic — Determination of tension set under constant elongation, and of
tension set, elongation and creep under constant tensile load
ISO/CD 5892
Rubber building gaskets — Materials for preformed solid vulcanized structural gaskets — Specification
ISO/CD 14285
Rubber and plastics gloves for the food industry and food services — Specification
TC 59
Buildings and civil engineering works
ISO/CD 21929-2
Sustainability in building construction - Sustainability indicators — Part 2: Framework for the
development of indicators for civil engineering works
TC 61
Plastics
ISO/CD 1872-1
Plastics — Polyethylene (PE) moulding and extrusion materials — Part 1: Designation system and
basis for specifications
TC 69
Applications of statistical methods
ISO/DTR 13519
Guidance on the development and use of ISO statistical publications supported by software
TC 92
Fire safety
ISO/CD 29903
Guidance for the comparison of toxic gas data from different tests
ISO/DTR 10796-2
Fire safety engineering — Part 2: Example on the application of IS 16730 to the assessment,
verification and validation of a CFD model
ISO/DTR 10796-3
Fire safety engineering — Part 3: Example on the application of IS 16730 to the assessment,
verification and validation of a structural model
ISO/DTR 10796-4
Fire safety engineering — Part 4: Example on the application of IS 16730 to the assessment,
verification and validation of an egress model
TC 107
Metallic and other inorganic coatings
ISO/DTR 15922
Metallic and other inorganic coatings — Evaluation of properties of dark stain phenomenon of
chromated coiled or sheet steel products
TC 108
Mechanical vibration, shock and condition monitoring
ISO/CD 20958-1
Condition monitoring and diagnostics of machines — Electrical signature analysis — Part 1: Threephase induction motors
TC 113
Hydrometry
ISO/CD 4359
Liquid flow measurement in open channels — Rectangular, trapezoidal and U-shaped flumes
TC 121
Anaesthetic and respiratory equipment
ISO 27427:2010/CD Amd 1
Anaesthetic and respiratory equipment — Nebulizing systems and components — Amendment 1
IEC/CD 60601-1-8
Medical electrical equipment — Part 1-8: General requirements for basic safety and essential
performance — Collateral standard: General requirements, tests and guidance for alarm systems in
medical electrical equipment and medical electrical systems
TC 131
Fluid power systems
ISO/CD 19973-1
Pneumatic fluid power — Assessment of component reliability by testing — Part 1: General procedures
ISO/CD 19973-2
Pneumatic fluid power — Assessment of component reliability by testing — Part 2: Directional control
valves
ISO/CD 19973-3
Pneumatic fluid power — Assessment of component reliability by testing — Part 3: Cylinders with
piston rod
ISO/CD 19973-4
Pneumatic fluid power — Assessment of component reliability by testing — Part 4: Pressure regulators
ISO/CD 19973-5
Pneumatic fluid power — Assessment of component reliability by testing — Part 5: Non-return valves,
shuttle valves, dual pressure valves, one-way adjustable flow control valves, quick-exhaust valves
TC 135
Non-destructive testing
ISO/DTS 11774
Non-destructive testing — Performance based qualification
TC 138
Plastics pipes, fittings and valves for the transport of fluids
ISO/CD 12230
Polybutene (PB) pipes — Effect of time and temperature on the expected strength
TC 150
Implants for surgery
ISO/DTS 10974
Requirements for the safety and compatibility of magnetic resonance imaging for patients with an
active implantable medical device
TC 156
Corrosion of metals and alloys
ISO/CD 7539-10
Corrosion of metals and alloys — Stress corrosion cracking — Part 10: Testing of alloys using reverse
U-bend test method
ISO/CD 16203
Corrosion of metals and alloys — Guidelines for selection of methods for erosion-corrosion testing in
flowing liquids
TC 165
Timber structures
ISO/PWI 12122
Timber Structures — Timber — Evaluation of characteristic values for structural timber
TC 172
Optics and photonics
ISO 10110-12:2007/CD
Amd 1
Optics and photonics — Preparation of drawings for optical elements and systems — Part 12: Aspheric
surfaces — Amendment 1
ISO/CD 8598-2
Optics and optical instruments — Focimeters — Part 2: Test lenses and methods for calibration and
verification of focimeters
ISO/CD 11979-2
Ophthalmic implants — Intraocular lenses — Part 2: Optical properties and test methods
ISO/CD 11979-7
Ophthalmic implants — Intraocular lenses — Part 7: Clinical investigations
TC 184
Automation systems and integration
ISO/CD 20140-1
Automation systems and integration — Environmental and energy efficiency evaluation method for
manufacturing systems — Part 1: Overview and general principles
TC 201
Surface chemical analysis
ISO/CD 16413
Evaluation of thickness, density and interface width of thin films by X-Ray reflectometry — Instrumental
requirements, alignment and positioning, data collection, analysis and reporting
TC 204
Intelligent transport systems
ISO/DTS 18234-1
Intelligent transport systems — Traffic and travel information via transport protocol expert group
(TPEG) data-streams — Part 1: Introduction, numbering and versions
ISO/DTS 18234-3
Intelligent transport systems — Traffic and travel information via transport protocol expert group
(TPEG) data-streams — Part 3: Service and Network Information (TPEG-SNI)
ISO/DTS 18234-7
Intelligent transport systems — Traffic and travel information via transport protocol expert group
(TPEG) data-streams — Part 7: Parking Information (TPEG-PKI)
ISO/DTS 18234-9
Intelligent transport systems — Traffic and travel information via transport protocol expert group
(TPEG) data-streams — Part 9: Traffic Event Compact (TPEG-TEC)
ISO/DTS 18234-10
Intelligent transport systems — Traffic and travel information via transport protocol expert group
(TPEG) data-streams — Part 10: Conditional access information (TPEG-CAI)
ISO/DTS 21219-2
Intelligent transport systems - Traffic and travel information via transport protocol expert group,
generation 2(TPEG2) — Part 2: UML modelling rules
ISO/DTS 21219-3
Intelligent transport systems - Traffic and travel information via transport protocol expert group,
generation 2(TPEG2) — Part 3: UML to binary conversion rules
ISO/DTS 21219-5
Intelligent transport systems - Traffic and travel information via transport protocol expert group,
generation 2(TPEG2) — Part 5: Service framework (TPEG2-SWF)
ISO/DTS 21219-6
Intelligent transport systems - Traffic and travel information via transport protocol expert group,
generation 2(TPEG2) — Part 6: Message management container (TPEG2-MMC)
ISO/DTS 21219-18
Intelligent transport systems - Traffic and Travel Information (TTI) via Transport Protocol Expert Group,
Generation 2(TPEG2) — Part 18: Traffic Flow and Prediction application (TPEG2-TFP)
TC 215
Health informatics
ISO/CD 18104
Health informatics — Integration of a reference terminology model for nursing
TC 227
Springs
ISO/CD 16249
Springs — Symbols
TC 228
Tourism and related services
ISO/CD 14785
Tourist information offices — Requirements for tourist information and reception services
TC 229
Nanotechnologies
ISO/DTS 13278
Carbon nanotubes — Determination of metal impurities in carbon nanotubes (CNTs) using inductively
coupled plasma-mass spectroscopy (ICP-MS)
TMB
Technical Management Board
ISO/IEC CD 80079-38
Explosive atmospheres — Part 38: Equipment and components in explosive atmospheres in
underground mines
JTC 1
Information technology
ISO/IEC CD 11693-1
Identification cards — Optical memory cards — Part 1: General characteristics
ISO/IEC CD 11694-1
Identification cards — Optical memory cards — Linear recording method — Part 1: Physical
characteristics
ISO/IEC CD 11694-2
Identification cards — Optical memory cards — Linear recording method — Part 2: Dimensions and
location of the accessible optical area
ISO/IEC 109184:1999/PDAM 1
Information technology — Digital compression and coding of continuous-tone still images: Registration
of JPEG profiles, SPIFF profiles, SPIFF tags, SPIFF colour spaces, APPn markers, SPIFF
compression types and Registration Authorities (REGAUT) — Part 4: — Amendment 1: Application
specific marker list
ISO/IEC 154442:2004/PDAM 4
Information technology — JPEG 2000 image coding system: Extensions — Part 2: — Amendment 4:
Block coder extension
ISO/IEC 19794-1/PDAM 2
Information technology — Biometric data interchange formats — Part 1: Framework — Amendment 2:
Conformance testing methodologies
ISO/IEC 19794-2.3/PDAM
1
Information technology — Biometric data interchange formats — Part 2: Finger minutiae data —
Amendment 1: Conformance testing methodology
ISO/IEC 19794-4.3/PDAM
1
Information technology — Biometric data interchange formats — Part 4: Finger image data —
Amendment 1: Conformance testing methodologies
ISO/IEC CD 19794-7
Information technology — Biometric data interchange formats — Part 7: Signature/sign time series data
ISO/IEC 19794-9/PDAM 1
Information technology — Biometric data interchange formats — Part 9: Vascular image data —
Amendment 1: Conformance testing methodology
ISO/IEC 19794-11/PDAM 1
Information technology — Biometric data interchange formats — Part 11: Signature/sign processed
dynamic data — Amendment 1: Conformance testing methodologies
DIS circulated
Period from 01 February to 28 February 2011
These documents have obtained substantial support within the appropriate ISO technical committee.
They have been submitted to the ISO member bodies for voting by the date shown.
* Available in English only
Vote
terminates
TC 2
Fasteners
ISO/DIS 888
*
Bolts, screws and studs — Nominal lengths, and thread lengths for general purpose bolts
2011-07-03
(Revision of ISO 888:1976)
TC 5
ISO/DIS 10380
Ferrous metal pipes and metallic fittings
*
Pipework — Corrugated metal hoses and hose assemblies
2011-07-18
(Revision of ISO 10380:2003)
TC 6
ISO/DIS
12625-7
Paper, board and pulps
*
Tissue paper and tissue products — Part 7: Determination of optical properties --Measurement
of brightness and colour
2011-07-11
(Revision of ISO 12625-7:2007)
TC 8
ISO/DIS 19292
Ships and marine technology
*
Ships and marine technology — Point-type resettable flame detectors for ships
2011-07-25
TC 17
ISO/DIS 15179
Steel
*
Hot-rolled twin-roll cast steel sheet of structural quality and high strength steel
2011-07-17
TC 20
ISO/DIS 17107
ISO/DIS 22671
Aircraft and space vehicles
*
*
Space data and information transfer systems — XML specification for navigation data
messages
2011-07-09
Space data and information transfer systems — Space link extension (SLE) — Forward
communications link transmission unit (CLTU) service
2011-07-02
(Revision of ISO 22671:2007)
ISO/DIS 22672
*
Space data and information transfer systems — Space link extension (SLE) — Forward space
packet service specification
2011-07-02
(Revision of ISO 22672:2006)
TC 22
Road vehicles
ISO/DIS
13209-2
Road vehicles — Open Test sequence eXchange format (OTX) — Part 2: Core data model
specification and requirements
ISO/DIS
14229-1
*
2011-07-26
Road vehicles — Unified diagnostic services (UDS) — Part 1: Specification and requirements
2011-07-09
(Revision of ISO 14229-1:2006)
ISO/DIS
14229-2
*
ISO/DIS
14229-4
*
Road vehicles — Unified diagnostic services (UDS) — Part 2: Session layer services
2011-07-02
Road vehicles — Unified diagnostic services (UDS) — Part 4: Unified diagnostic services on
FlexRay implementation (UDSonFR)
2011-07-02
ISO/DIS 13296
*
Diesel engines — High-pressure fuel injection pipe assemblies — General requirements and
dimensions
2011-07-25
(Revision of ISO 13296:2005)
TC 23
Tractors and machinery for agriculture and forestry
ISO 37671:1998/DAmd
2
*
ISO/DIS
15886-1
*
Tractors, machinery for agriculture and forestry, powered lawn and garden equipment —
Symbols for operator controls and other displays — Part 1: Common symbols — Amendment 2:
Additional symbols concerning mainly the engine emissions system
2011-07-08
Agricultural irrigation equipment — Sprinklers — Part 1: Definition of terms and classification
2011-07-12
(Revision of ISO 15886-1:2004)
TC 34
Food products
ISO/DIS 16297
Milk — Bacterial count — Protocol for the evaluation of alternative methods
2011-07-17
TC 35
Paints and varnishes
ISO/DIS 15091
Paints and varnishes — Determination of the electrical conductivity and the specific electrical
resistivity
TC 37
ISO/DIS
10241-2.2
Terminology and other language and content resources
*
Textiles
*
TC 45
ISO/DIS 13507
Terminological entries in standards — Part 2: Adoption of standardized terminological entries
2011-04-12
TC 38
ISO
11092:1993/D
Amd 1
2011-07-18
Textiles — Physiological effects — Measurement of thermal and water-vapour resistance under
steady-state conditions (sweating guarded-hotplate test) — Amendment 1
2011-07-11
Rubber and rubber products
*
Rubber compounds — Short names for properties reported in certificates of analysis
2011-07-10
ISO/DIS 2951
*
Vulcanized rubber — Determination of insulation resistance
2011-07-05
(Revision of ISO 2951:1974)
ISO/DIS 33842
*
ISO 99242:2000/DAmd
1
*
ISO/DIS 13145
*
ISO/DIS 4652
*
Rubber, vulcanized or thermoplastic — Determination of stress relaxation in compression —
Part 2: With temperature cycling
Rubber and rubber products — Determination of the composition of vulcanizates and uncured
compounds by thermogravimetry — Part 2: Acrylonitrile-butadiene and halobutyl rubbers —
Amendment 1
Rubber — Determination of viscosity and stress relaxation using a rotorless, sealed oscillatingshear rheometer
Rubber compounding ingredients — Carbon black — Determination of specific surface area by
2011-07-05
2011-07-02
2011-07-15
nitrogen adsorption methods — Single-point procedures
2011-07-05
(Revision of ISO 4652-1:1994)
TC 58
ISO/DIS
21007-2
Gas cylinders
*
Gas cylinders — Identification and marking using radio frequency identification technology —
Part 2: Numbering schemes for radio frequency identification
2011-07-04
(Revision of ISO 21007-2:2005)
TC 61
Plastics
ISO/DIS 9352
Plastics — Determination of resistance to wear by abrasive wheels
2011-07-29
(Revision of ISO 9352:1995)
ISO/DIS 9772
*
Cellular plastics — Determination of horizontal burning characteristics of small specimens
subjected to a small flame
2011-07-05
(Revision of ISO 9772:2001, ISO 9772:2001/Amd 1:2003)
ISO 16281:2009/DAmd
1
*
TC 68
ISO/DIS
11568-2
Plastics — Determination of the viscosity of polymers in dilute solution using capillary
viscometers — Part 1: General principles — Amendment 1
2011-07-11
Financial services
*
Financial services — Key management (retail) — Part 2: Symmetric ciphers, their key
management and life cycle
2011-07-10
(Revision of ISO 11568-2:2005)
TC 79
ISO/DIS 8287
Light metals and their alloys
*
Magnesium and magnesium alloys — Unalloyed magnesium — Chemical composition
2011-07-08
(Revision of ISO 8287:2000)
TC 85
ISO/DIS
29661.2
Nuclear energy, nuclear technologies, and radiological protection
*
2011-04-19
TC 111
ISO/DIS 7597
Reference radiation fields for radiation protection — Definitions and fundamental concepts
Round steel link chains, chain slings, components and accessories
*
Forged steel lifting hooks with point and eye for use with grade 8 chain
2011-07-05
(Revision of ISO 7597:1987)
TC 123
ISO/DIS 4381
Plain bearings
*
Plain bearings — Tin casting alloys for multilayer plain bearings
2011-07-08
(Revision of ISO 4381:2000)
TC 126
Tobacco and tobacco products
ISO/DIS 20193
*
Tobacco and tobacco products — Determination of the width of the strands of cut tobacco
2011-07-29
TC 127
Earth-moving machinery
ISO/DIS 10987
Earth-moving machinery — Sustainability — Terminology, sustainability factors and reporting
2011-07-05
TC 131
ISO/DIS
10770-2
Fluid power systems
*
Hydraulic fluid power — Electrically modulated hydraulic control valves — Part 2: Test methods
for three-way directional flow control valves
2011-07-29
(Revision of ISO 10770-2:1998)
TC 135
ISO/DIS 9712
Non-destructive testing
*
Non-destructive testing — Qualification and certification of NDT personnel — General principles
2011-07-18
(Revision of ISO 9712:2005, ISO 9712:2005/Cor 1:2006)
TC 142
ISO/DIS 29462
Cleaning equipment for air and other gases
*
TC 150
2011-07-18
Implants for surgery
ISO/DIS 64742.2
*
ISO/DIS 58403
*
ISO
7199:2009/DA
md 1
*
ISO/DIS 11658
*
TC 156
ISO/DIS 14802
Field testing of general ventilation filtration devices and systems for in situ removal efficiency by
particle size and resistance to airflow
Implants for surgery — Ceramic materials — Part 2: Composite materials based on a high purity
alumina matrix with zirconia reinforcement
2011-04-17
Cardiovascular implants — Cardiac valve prostheses — Part 3: Heart valve substitutes
implanted by minimally invasive techniques
2011-07-25
Cardiovascular implants and artificial organs — Blood-gas exchangers (oxygenators) —
Amendment 1: Clarifications for test methodologies, labelling, and sampling schedule
2011-07-17
Cardiovascular implants and extracorporeal systems — Blood/tissue contact surface
modifications for extracorporeal perfusion systems
2011-07-17
Corrosion of metals and alloys
*
Corrosion of metals and alloys — Guidelines for applying statistics to analysis of corrosion data
2011-07-05
TC 163
ISO/DIS 14857
Thermal performance and energy use in the built environment
*
TC 164
ISO/DIS 49651
Thermal performance in the built environment — Determination of air permeance of building
materials
2011-07-23
Mechanical testing of metals
*
Metallic materials — Fatigue testing — Uniaxial dynamic force calibration — Part 1: Testing
systems
(Revision of ISO 4965:1979)
2011-07-03
ISO/DIS 49652
*
Metallic materials — Fatigue testing — Uniaxial dynamic force calibration — Part 2: Dynamic
calibration device (DCD) instrumentation
2011-07-03
(Revision of ISO 4965:1979)
ISO/DIS 12107
*
Metallic materials — Fatigue testing — Statistical planning and analysis of data
2011-07-09
(Revision of ISO 12107:2003)
TC 172
Optics and photonics
ISO/DIS
16331-1
Optics and optical instruments — Laboratory procedures for testing surveying and construction
instruments — Part 1: Performance of handheld laser distance meters
TC 173
Assistive products for persons with disability
ISO/DIS 717611
*
2011-07-22
Wheelchairs — Part 11: Test dummies
2011-07-10
(Revision of ISO 7176-11:1992)
ISO/DIS 717616
*
Wheelchairs — Part 16: Resistance to ignition of upholstered parts — Requirements and test
methods
2011-07-10
(Revision of ISO 7176-16:1997)
TC 176
ISO/DIS 10004
Quality management and quality assurance
*
Quality management — Customer satisfaction — Guidelines for monitoring and measuring
2011-07-29
(Revision of ISO/TS 10004:2010)
TC 190
ISO/DIS 13196
Soil quality
*
TC 198
ISO/DIS
13408-7
2011-07-11
Sterilization of health care products
*
TC 205
ISO/DIS
11855-5
Soil quality — Screening soils for selected elements by energy-dispersive X-ray fluorescence
spectrometry using a handheld or portable instrument
Aseptic processing of health care products — Part 7: Alternative processes for atypical medical
devices and combination products
2011-07-26
Building environment design
*
Building environment design — Standards for the design, construction and operation of radiant
heating and cooling systems — Part 5: Installation
TC 211
Geographic information/Geomatics
ISO/DIS 19155
Geographic information — Place Identifier (PI) architecture
2011-07-10
2011-07-29
TC 227
ISO/DIS
11891.2
Springs
*
Hot formed helical compression springs — Technical specifications
2011-04-18
JTC 1
Information technology
ISO/IEC DIS
40210
Information technology — W3C SOAP Version 1.2 Part 1: Messaging Framework (Second
Edition)
ISO/IEC DIS
40220
Information technology — W3C SOAP Version 1.2 Part 2: Adjuncts (Second Edition)
ISO/IEC DIS
40230
Information technology — W3C SOAP Message Transmission Optimization Mechanism
ISO/IEC DIS
40240
Information technology — W3C Web Services Addressing 1.0 — Core
ISO/IEC DIS
40250
Information technology — W3C Web Services Addressing 1.0 — SOAP Binding
ISO/IEC DIS
40260
Information technology — W3C Web Services Addressing 1.0 — Metadata
ISO/IEC DIS
40270
Information technology — W3C Web Services Policy 1.5 — Framework
ISO/IEC DIS
40280
Information technology — W3C Web Services Policy 1.5 — Attachment
ISO/IEC DIS
23271
2011-07-26
2011-07-26
2011-07-26
2011-07-26
2011-07-26
2011-07-26
2011-07-26
2011-07-26
*
Information technology — Common Language Infrastructure (CLI)
2011-07-03
(Revision of ISO/IEC 23271:2006)
ISO/IEC
144964:2004/DAmd
40
*
ISO/IEC
144965:2001/DAmd
29
*
Information technology — Coding of audio-visual objects — Part 4: Conformance testing —
Amendment 40: ExtendedCore2D conformance
Information technology — Coding of audio-visual objects — Part 5: Reference software —
Amendment 29: Reference software for LASeR presentation and modification of structured
information (PMSI) tools
2011-07-16
2011-07-19
ISO/IEC
144965:2001/DAmd
30
Information technology — Coding of audio-visual objects — Part 5: Reference software —
Amendment 30: ExtendedCore2D reference software
2011-07-16
ISO/IEC
1449612:2008/DAmd
3
Information technology — Coding of audio-visual objects — Part 12: ISO base media file format
— Amendment 3: DASH support and RTP reception hint track processing
2011-07-16
Information technology — Coding of audio-visual objects — Part 15: Advanced Video Coding
(AVC) file format — Amendment 1: Sub-track definitions
2011-07-16
Information technology — JPEG 2000 image coding system — Part 12: ISO base media file
format — Amendment 3: DASH support and RTP reception hint track processing
2011-07-16
ISO/IEC
1449615:2010/DAmd
1
ISO/IEC
1544412:2008/DAmd
3
*
ISO/IEC
210008:2008/DAmd
2
Information technology — Multimedia framework (MPEG-21) — Part 8: Reference software —
Amendment 2: Reference software for media value chain ontology (MVCO)
2011-07-16
ISO/IEC
2300011:2009/DAmd
2
Information technology — Multimedia application format (MPEG-A) — Part 11: Stereoscopic
video application format — Amendment 2: Signalling of additional composition type and profiles
2011-07-16
ISO/IEC DIS
23001-6
Information technology — MPEG systems technologies — Part 6: Dynamic adaptive streaming
over HTTP (DASH)
2011-07-16
ISO/IEC DIS
23003-3
Information technology — MPEG audio technologies — Part 3: Unified speech and audio coding
ISO/IEC
230071:2010/DAmd
1
Information technology — Rich media user interfaces — Part 1: Widgets — Amendment 1:
Widget extensions
ISO/IEC DIS
17203
Information technology — Open Virtualization Format (OVF) specification
2011-07-16
2011-07-16
2011-07-29
FDIS circulated
Period from 01 February to 28 February 2011
These Final draft International Standards have been submitted to the ISO member bodies for formal approval by the date shown
* Available in English only
Vote terminates
TC 5
ISO/FDIS 7186
Ferrous metal pipes and metallic fittings
*
Ductile iron products for sewerage applications
2011-04-22
(Revision of ISO 7186:1996)
TC 8
ISO/FDIS
23269-3
Ships and marine technology
*
TC 20
ISO/FDIS
24113
Ships and marine technology — Breathing apparatus for ships — Part 3: Self-contained
breathing apparatus (safety equipment) required by the IMO IBC and IGC Codes
2011-04-08
Aircraft and space vehicles
*
Space systems — Space debris mitigation requirements
2011-04-18
(Revision of ISO 24113:2010)
TC 22
Road vehicles
ISO
11838:1997/F
DAmd 1
*
ISO
14722:1998/F
DAmd 1
*
2011-04-15
Moped and moped-rider kinematics — Vocabulary — Amendment 1
2011-04-15
TC 29
ISO/FDIS 3860
Motorcycle and motorcycle-rider kinematics — Vocabulary — Amendment 1
Small tools
*
Bore cutters with key drive — Form milling cutters with constant profile
2011-04-17
(Revision of ISO 3860:1976)
ISO/FDIS 6462
*
Face and shoulder milling cutters with indexable inserts — Dimensions
2011-04-12
(Revision of ISO 6462:1983)
TC 30
ISO/FDIS
22158
Measurement of fluid flow in closed conduits
*
2011-04-25
TC 34
ISO/FDIS
11287
Food products
*
Terminology and other language and content resources
*
Language resource management — Persistent identification and sustainable access (PISA)
2011-04-17
TC 51
ISO/FDIS
8611-1
Green tea — Definition and basic requirements
2011-04-08
TC 37
ISO/FDIS
24619
Input/output protocols and electronic interfaces for water meters — Requirements
Pallets for unit load method of materials handling
*
Pallets for materials handling — Flat pallets — Part 1: Test methods
2011-04-12
(Revision of ISO 8611-1:2004)
ISO/FDIS
8611-2
*
Pallets for materials handling — Flat pallets — Part 2: Performance requirements and
selection of tests
2011-04-12
(Revision of ISO/TS 8611-2:2005)
ISO/FDIS
8611-3
*
Pallets for materials handling — Flat pallets — Part 3: Maximum working loads
2011-04-12
(Revision of ISO/TS 8611-3:2005)
TC 61
ISO/FDIS
11357-3
Plastics
*
Plastics — Differential scanning calorimetry (DSC) — Part 3: Determination of temperature
and enthalpy of melting and crystallization
(Revision of ISO 11357-3:1999, ISO 11357-3:1999/Amd 1:2005)
TC 67
Materials, equipment and offshore structures for petroleum, petrochemical
2011-04-08
and natural gas industries
ISO/FDIS
13501
*
Petroleum and natural gas industries — Drilling fluids — Processing equipment evaluation
2011-04-25
(Revision of ISO 13501:2005)
TC 83
ISO/FDIS 7794
Sports and recreational equipment
*
Cross-country skis — Ski-binding screws — Requirements
2011-04-16
(Revision of ISO 7794:1991)
ISO/FDIS
10228
*
Cross-country skis — Binding mounting area — Requirements for test screws
2011-04-16
(Revision of ISO 10228:1991)
TC 85
ISO/FDIS
20785-2
Nuclear energy, nuclear technologies, and radiological protection
*
TC 89
ISO 124604:2008/FDAmd
1
*
Wood-based panels — Determination of formaldehyde release — Part 4: Desiccator method
— Amendment 1
2011-04-16
Leather
*
Leather — Upholstery leather characteristics — Selection of leather for furniture
2011-04-08
TC 130
ISO/FDIS
12642-1
2011-04-05
Wood-based panels
TC 120
ISO/FDIS
16131
Dosimetry for exposures to cosmic radiation in civilian aircraft — Part 2: Characterization of
instrument response
Graphic technology
*
Graphic technology — Input data for characterization of four-colour process printing — Part 1:
Initial data set
2011-04-22
(Revision of ISO 12642-1:1996, ISO 12642-1:1996/Cor 1:2005)
TC 135
ISO/FDIS
10878
Non-destructive testing
*
2011-04-10
TC 138
ISO/FDIS
21307
Non-destructive testing — Infrared thermography — Vocabulary
Plastics pipes, fittings and valves for the transport of fluids
*
Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) pipes and
fittings used in the construction of gas and water distribution systems
2011-04-17
(Revision of ISO 21307:2009)
ISO/FDIS
25780
*
TC 145
ISO/FDIS 7010
Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or
sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated
polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking
techniques
2011-04-18
Graphical symbols
*
Graphical symbols — Safety colours and safety signs — Registered safety signs
2011-04-12
(Revision of ISO 7010:2003, ISO 7010:2003/Amd 1:2006, ISO 7010:2003/FDAmd 50, ISO
7010:2003/FDAmd 55, ISO 7010:2003/FDAmd 56, ISO 7010:2003/FDAmd 57, ISO
7010:2003/FDAmd 59, ISO 7010:2003/FDAmd 60, ISO 7010:2003/Amd 2:2007, ISO
7010:2003/Amd 3:2007, ISO 7010:2003/FDAmd 61, ISO 7010:2003/DAmd 75, ISO
7010:2003/DAmd 76, ISO 7010:2003/Amd 4:2009, ISO 7010:2003/Amd 5:2010, ISO
7010:2003/Amd 6:2010)
TC 146
ISO/FDIS
11057
Air quality
*
2011-04-24
TC 150
ISO/FDIS
23500
Implants for surgery
*
TC 157
ISO/FDIS 7439
Air quality — Test method for filtration characterization of cleanable filter media
Guidance for the preparation and quality management of fluids for haemodialysis and related
therapies
2011-04-10
Non-systemic contraceptives and STI barrier prophylactics
*
Copper-bearing contraceptive intrauterine devices — Requirements and tests
2011-05-11
(Revision of ISO 7439:2002)
TC 172
ISO 119798:2006/FDAmd
1
Optics and photonics
*
TC 190
ISO/FDIS
11709
*
Soil quality — Determination of selected coal-tar-derived phenolic compounds using high
performance liquid chromatography (HPLC)
2011-04-17
Fine ceramics
*
TC 213
ISO/FDIS 5459
2011-04-18
Soil quality
TC 206
ISO/FDIS
13124
Ophthalmic implants — Intraocular lenses — Part 8: Fundamental requirements —
Amendment 1
Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for
interfacial bond strength of ceramic materials
2011-04-12
Dimensional and geometrical product specifications and verification
*
Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum
systems
2011-04-18
(Revision of ISO 5459:1981, ISO/DIS 5459-1, ISO/DIS 5459-2)
ISO/FDIS
8015.2
*
Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules
2011-04-18
(Revision of ISO 8015:1985, ISO/DIS 14659.2)
ISO/FDIS
16610-21
*
Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters:
Gaussian filters
2011-04-02
(Revision of ISO 11562:1996)
IULTCS
ISO/FDIS
17226-3
International Union of Leather Technologists and Chemists Societies
*
Leather — Chemical determination of formaldehyde content — Part 3: Determination of
formaldehyde emissions from leather
2011-04-11
JTC 1
Information technology
ISO/IEC FDIS
29168-1
*
ISO/IEC FDIS
24789-2
*
ISO/IEC FDIS
12862
*
Information technology — Open systems interconnection — Part 1: Object identifier resolution
system (ORS)
2011-04-15
Identification cards — Card service life — Part 2: Methods of evaluation
2011-04-23
Information technology — 120 mm (8,54 Gbytes per side) and 80 mm (2,66 Gbytes per side)
DVD recordable disk for dual layer (DVD-R for DL)
2011-04-29
(Revision of ISO/IEC 12862:2009)
ISO/IEC FDIS
27005
*
Information technology — Security techniques — Information security risk management
2011-04-22
(Revision of ISO/IEC 27005:2008)
ISO/IEC FDIS
10918-5
*
ISO/IEC
144965:2001/FDAmd
28
*
ISO/IEC
154441:2004/FDAmd
4
*
ISO/IEC FDIS
23005-6
*
ISO/IEC FDIS
11581-40
*
ISO/IEC FDIS
13066-1
*
ISO/IEC FDIS
15897
*
Information technology — Digital compression and coding of continuous-tone still images:
JPEG File Interchange Format (JFIF) — Part 5:
2011-04-03
Information technology — Coding of audio-visual objects — Part 5: Reference software —
Amendment 28: Reference software for LASeR adaptation tools
2011-04-03
Information technology — JPEG 2000 image coding system: Core coding system — Part 1:
— Amendment 4: Guidelines for digital cinema applications
2011-04-03
Information technology — Media context and control — Part 6: Common types and tools
2011-04-03
Information technology — User interface icons — Part 40: Management of icon registration
2011-04-23
Information technology — Interoperability with assistive technology (AT) — Part 1:
Requirements and recommendations for interoperability
2011-04-23
Information technology — User interfaces — Procedures for the registration of cultural
elements
2011-04-23
(Revision of ISO/IEC 15897:1999)
ISO/IEC FDIS
19788-2
*
Information technology — Learning, education and training — Metadata for learning resources
— Part 2: Dublin Core elements
Standards published
New International Standards published between 01 February and 28 February 2011
2011-04-23
* Available in English only
** French version of standard previously published in English only
Price group
TC 2
Fasteners
ISO
14585:2011
Hexalobular socket pan head tapping screws
ISO
14586:2011
Hexalobular socket countersunk head tapping screws
ISO
14587:2011
Hexalobular socket raised countersunk (oval) head tapping screws
TC 4
Rolling bearings
ISO
9628:2006/Am
d 1:2011
Rolling bearings — Insert bearings and eccentric locking collars — Boundary dimensions and
tolerances — Amendment 1: Diameter series 3
TC 6
Paper, board and pulps
ISO 7263:2011
Corrugating medium — Determination of the flat crush resistance after laboratory fluting
B
B
B
XZ
D
TC 8
ISO 280052:2011
Ships and marine technology
*
Security management systems for the supply chain — Electronic port clearance (EPC) — Part
2: Core data elements
TC 10
Technical product documentation
ISO 141451:1998/Amd
1:2011
Roller ball pens and refills — Part 1: General use — Amendment 1: Ball diameter for tip
classification
TC 17
Steel
ISO 5952:2011
*
TC 20
XZ
F
Aircraft and space vehicles
ISO
27470:2011
*
ISO
23460:2011
*
ISO
27026:2011
*
TC 22
Continuously hot-rolled steel sheet of structural quality with improved atmospheric corrosion
resistance
X
Aircraft ground equipment — Upper deck catering vehicle — Functional requirements
D
Space projects — Programme management — Dependability assurance requirements
J
Space systems — Programme management — Breakdown of project management structures
F
Road vehicles
ISO 157654:2011
*
ISO
14793:2011
*
ISO
14794:2011
*
ISO
16333:2011
*
ISO 172881:2011
*
ISO 172882:2011
*
Road vehicles — Diagnostic communication over Controller Area Network (DoCAN) — Part 4:
Requirements for emissions-related systems
N
Road vehicles — Heavy commercial vehicles and buses — Lateral transient response test
methods
N
Heavy commercial vehicles and buses — Braking in a turn — Open-loop test methods
L
Heavy commercial vehicles and buses — Steady-state rollover threshold — Tilt-table test
method
H
Passenger cars — Free-steer behaviour — Part 1: Steering-release open-loop test method
D
Passenger cars — Free-steer behaviour — Part 2: Steering-pulse open-loop test method
G
TC 23
Tractors and machinery for agriculture and forestry
ISO
22868:2011
Forestry and gardening machinery — Noise test code for portable hand-held machines with
internal combustion engine — Engineering method (Grade 2 accuracy)
TC 28
Petroleum products and lubricants
ISO 207831:2011
Petroleum and related products — Determination of emulsion stability of fire-resistant fluids —
Part 1: Fluids in category HFAE
TC 34
Food products
ISO 7301:2011
Rice — Specification
Q
D
K
ISO 129662:2011
*
ISO
27107:2008
*
H
Animal and vegetable fats and oils — Determination of peroxide value — Potentiometric endpoint determination
E
Green coffee — Determination of water content — Basic reference method — Amendment 1
ISO
1446:2001/Am
d 1:2011
ISO 8455:2011
Animal and vegetable fats and oils — Gas chromatography of fatty acid methyl esters — Part
2: Preparation of methyl esters of fatty acids
XZ
*
Green coffee — Guidelines for storage and transport
C
TC 35
Paints and varnishes
ISO 28111:2011
Paints and varnishes — Determination of density — Part 1: Pyknometer method
ISO 28112:2011
Paints and varnishes — Determination of density — Part 2: Immersed body (plummet)
method
ISO 28113:2011
Paints and varnishes — Determination of density — Part 3: Oscillation method
E
E
D
ISO 28114:2011
Paints and varnishes — Determination of density — Part 4: Pressure cup method
TC 39
Machine tools
ISO
29262:2011
D
*
Production equipment for microsystems — Interface between end effector and handling
system
TC 45
Rubber and rubber products
ISO 4660:2011
Rubber, raw natural — Colour index test
J
C
ISO 4635:2011
*
Rubber, vulcanized — Preformed joint seals for use between concrete paving sections of
highways — Specification
TC 61
Plastics
ISO 103502:2011
Plastics — Acquisition and presentation of comparable single-point data — Part 2: Long-fibrereinforced plastics
ISO 8516:2011
Textile glass — Textured yarns — Basis for a specification
F
E
B
TC 68
ISO 95641:2011
Financial services
*
Financial services — Personal Identification Number (PIN) management and security — Part
1: Basic principles and requirements for PINs in card-based systems
N
TC 79
Light metals and their alloys
ISO 2106:2011
Anodizing of aluminium and its alloys — Determination of mass per unit area (surface density)
of anodic oxidation coatings — Gravimetric method
C
Anodizing of aluminium and its alloys — Rating system for the evaluation of pitting corrosion
— Grid method
B
ISO 8994:2011
TC 92
Fire safety
ISO 263671:2011
Guidelines for assessing the adverse environmental impact of fire effluents — Part 1: General
TC 94
Personal safety -- Protective clothing and equipment
ISO
16073:2011
J
*
Wildland firefighting personal protective equipment — Requirements and test methods
W
TC 106
Dentistry
ISO 3107:2011
Dentistry — Zinc oxide/eugenol cements and zinc oxide/non-eugenol cements
E
ISO
27020:2010
Dentistry — Brackets and tubes for use in orthodontics
TC 119
Powder metallurgy
F
Metallic powders — Determination of tap density
ISO 3953:2011
B
TC 121
ISO 810602:2009/Cor
1:2011
Anaesthetic and respiratory equipment
*
Non-invasive sphygmomanometers — Part 2: Clinical validation of automated measurement
type — Technical Corrigendum 1
free
TC 138
Plastics pipes, fittings and valves for the transport of fluids
ISO 112963:2009
Plastics piping systems for renovation of underground non-pressure drainage and sewerage
networks — Part 3: Lining with close-fit pipes
K
ISO 121763:2011
Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 3:
Operator's badge
D
ISO
10639:2004/A
md 1:2011
*
Plastics piping systems for pressure and non-pressure water supply — Glass-reinforced
thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin —
Amendment 1
TC 145
Graphical symbols
ISO 38642:2004/Amd
1:2011
Graphical symbols — Safety colours and safety signs — Part 2: Design principles for product
safety labels — Amendment 1: Revision of Table B.1
TC 147
Water quality
ISO 566723:2011
Water quality — Sampling — Part 23: Guidance on passive sampling in surface waters
TC 150
Implants for surgery
XZ
L
ISO
17853:2011
*
ISO 181921:2011
*
Wear of implant materials — Polymer and metal wear particles — Isolation and
characterization
Implants for surgery — Wear of total intervertebral spinal disc prostheses — Part 1: Loading
and displacement parameters for wear testing and corresponding environmental conditions for
test
TC 157
Non-systemic contraceptives and STI barrier prophylactics
ISO
16037:2002/A
md 1:2011
Rubber condoms for clinical trials — Measurement of physical properties — Amendment 1
ISO
23409:2011
XZ
H
M
XZ
*
Male condoms — Requirements and test methods for condoms made from synthetic materials
S
TC 164
Mechanical testing of metals
ISO 68922:2011
Metallic materials — Tensile testing — Part 2: Method of test at elevated temperature
TC 172
Optics and photonics
ISO 8624:2011
Ophthalmic optics — Spectacle frames — Measuring system and terminology
K
E
TC 184
ISO 1030352:2011
Automation systems and integration
*
Industrial automation systems and integration — Product data representation and exchange
— Part 52: Integrated generic resource: Mesh-based topology
TC 211
Geographic information/Geomatics
ISO
19143:2010
Geographic information — Filter encoding
TC 215
Health informatics
ISO 129671:2009
Health informatics — Service architecture — Part 1: Enterprise viewpoint
ISO 129672:2009
Health informatics — Service architecture — Part 2: Information viewpoint
ISO 129673:2009
Health informatics — Service architecture — Part 3: Computational viewpoint
ISO
21090:2011
W
X
U
U
N
*
Health informatics — Harmonized data types for information interchange
XD
TC 216
Footwear
ISO
10748:2011
Footwear — Test method for slide fasteners — Slider locking strength
JTC 1
Information technology
C
ISO/IEC
24793-1:2011
*
ISO/IEC
24793-2:2011
*
ISO/IEC
15026-2:2011
*
ISO/IEC
15909-2:2011
*
ISO/IEC
25040:2011
*
ISO/IEC TR
14165372:2011
*
ISO/IEC
180331:2005/Amd
1:2011
*
ISO/IEC
14496-
*
Information technology — Mobile multicast communications: Framework — Part 1:
L
Information technology — Mobile multicast communications: Protocol over native IP multicast
networks — Part 2:
K
Systems and software engineering — Systems and software assurance — Part 2: Assurance
case
E
Systems and software engineering — High-level Petri nets — Part 2: Transfer format
XA
Systems and software engineering — Systems and software Quality Requirements and
Evaluation (SQuaRE) — Evaluation process
S
Information technology — Fibre Channel — Part 372: Methodologies of interconnects-2 (FCMI-2)
V
Information technology — Security techniques — Encryption algorithms — Part 1: General —
Amendment 1
XZ
Information technology — Coding of audio-visual objects — Part 5: Reference software —
Amendment 27: Scalable complexity 3D mesh coding reference software
XZ
5:2001/Amd
27:2011
ISO/IEC
1449626:2010/Cor
2:2011
*
ISO/IEC
1593812:2008/Amd
1:2011
*
ISO/IEC
19784-4:2011
*
ISO/IEC
19795-5:2011
*
Information technology — Coding of audio-visual objects — Part 26: Audio conformance —
Technical Corrigendum 2
free
Information technology — Multimedia content description interface — Part 12: Query format
— Amendment 1: Reference software and flat metadata output
M
Information technology — Biometric application programming interface — Part 4: Biometric
sensor function provider interface
R
Information technology — Biometric performance testing and reporting — Part 5: Access
control scenario and grading scheme
R
Standards confirmed
The following International Standards are confimred for a five year period:
TC 2
Fasteners
ISO 887:2000
(reconfirmed)
ISO 4759-3:2000
(reconfirmed)
ISO 7089:2000
(reconfirmed)
ISO 7090:2000
(reconfirmed)
ISO 7091:2000
(reconfirmed)
ISO 7092:2000
(reconfirmed)
ISO 7093-1:2000
(reconfirmed)
ISO 7094:2000
(reconfirmed)
ISO 14588:2000
(reconfirmed)
ISO 15973:2000
(reconfirmed)
ISO 15974:2000
(reconfirmed)
TC 24
Particle characterization including sieving
ISO 20998-1:2006
TC 27
Solid mineral fuels
ISO 15239:2005
TC 29
Small tools
ISO 9138:1993
(reconfirmed)
TC 34
Food products
ISO 5508:1990
(reconfirmed)
ISO 15304:2002
TC 35
Paints and varnishes
ISO 11890-1:2007
TC 38
Textiles
ISO 8498:1990
(reconfirmed)
TC 67
Materials, equipment and offshore structures for petroleum, petrochemical
and natural gas industries
ISO 10405:2000
(reconfirmed)
TC 94
Personal safety -- Protective clothing and equipment
ISO 13995:2000
TC 102
Iron ore and direct reduced iron
ISO 10203:2006
ISO 10204:2006
TC 107
Metallic and other inorganic coatings
ISO 3497:2000
(reconfirmed)
ISO 3543:2000
(reconfirmed)
ISO 10111:2000
(reconfirmed)
ISO 10587:2000
(reconfirmed)
TC 122
Packaging
ISO 2233:2000
(reconfirmed)
ISO 2234:2000
(reconfirmed)
ISO 2244:2000
(reconfirmed)
ISO 2247:2000
(reconfirmed)
ISO 2248:1985
(reconfirmed)
ISO 2873:2000
(reconfirmed)
ISO 2875:2000
(reconfirmed)
ISO 2876:1985
(reconfirmed)
ISO 8318:2000
(reconfirmed)
ISO 12048:1994
(reconfirmed)
ISO 23667:2007
TC 146
Air quality
ISO 10396:2007
ISO 16000-9:2006
ISO 16000-10:2006
ISO 16000-11:2006
TC 163
Thermal performance and energy use in the built environment
ISO 15927-6:2007
JTC 1
Information technology
ISO/IEC 2382-8:1998
(reconfirmed)
ISO/IEC 2382-14:1997
(reconfirmed)
ISO/IEC 2382-25:1992
(reconfirmed)
ISO/IEC 2382-31:1997
(reconfirmed)
ISO/IEC 10164-4:1992
(reconfirmed)
ISO/IEC 10164-7:1992
(reconfirmed)
ISO/IEC 10164-15:2002
ISO/IEC 10164-16:1997
(reconfirmed)
ISO/IEC 10164-18:1997
(reconfirmed)
ISO/IEC 10165-4:1992
(reconfirmed)
ISO/IEC 9318-4:2002
ISO/IEC 9798-4:1999
(reconfirmed)
ISO/IEC 18032:2005
Standards withdrawn
Period from 01 February to 28 February 2011
TC 8
Ships and marine technology
ISO/PAS 28005-2:2009
(replaced by ISO 28005-2:2011)
TC 22
Road vehicles
ISO 1919:1998
(replaced by )
ISO 2344:1998
(replaced by )
ISO 2345:1994
(replaced by )
ISO 2347:1994
(replaced by )
ISO 2704:1998
(replaced by )
ISO 2705:2006
(replaced by )
ISO 8470:2006
(replaced by )
ISO 14508:2006
(replaced by )
ISO 16246:2005
(replaced by )
ISO 19812:2006
(replaced by )
ISO 22977:2005
(replaced by )
TC 34
Food products
ISO 5509:2000
(replaced by ISO 12966-2:2011)
TC 45
Rubber and rubber products
ISO 18752:2006/Amd 1:2010
(replaced by )
TC 68
Financial services
ISO 9564-3:2003
(replaced by ISO 9564-1:2011)
TC 87
Cork
ISO 2191:1972
(replaced by )
ISO 9148:1987
(replaced by )
TC 164
Mechanical testing of metals
ISO 783:1999
(replaced by ISO 6892-2:2011)
Meeting calendar
(update at 01 February 2011)
Meetings called for the month of January are not in this edition.
* Information definite but meeting not yet formally convened
** Provisional
March 2011
1-3
Atlanta (USA)
JTC 2
Joint Project Committee - Energy efficiency and renewable energy sources - Common
terminology
2
Bangkok
(Thailand)
TC 122
Packaging
3
Frankfurt
(Germany)
TC 131/SC 6
Fluid power systems/Contamination control
3-4
Berlin (Germany)
TC 58/SC 4
Gas cylinders/Operational requirements for gas cylinders
7-8
Berlin (Germany)
TC 1
Screw threads
7-9
Sydney
(Australia)
TC 243
Project Committee: Consumer product safety
7-11
Sydney
(Australia)
TC 240
Project Committee: Product recall
11
Paris (France)
TC 22/SC 21
Road vehicles/Electrically propelled road vehicles
17-18
Geneva
(Switzerland)
COUNCIL
Council
18
Strasbourg
(France)
JTC 1/SC 36
Information technology/Information technology for learning, education and training
18-19
Tokyo (Japan)
TC 219
Floor coverings
23-24
Ottawa (Canada)
TC 245
Project Committee: Cross-border trade of second-hand goods
24
Milan (Italy)
TC 118/SC 3
Compressors and pneumatic tools, machines and equipment/Pneumatic tools and
machines
24
Milan (Italy)
TC 118/SC 4
Compressors and pneumatic tools, machines and equipment/Compressed air purity
specification and compressed air treatment equipment
24
Milan (Italy)
TC 118/SC 6
Compressors and pneumatic tools, machines and equipment/Air compressors and
compressed air systems
25
Milan (Italy)
TC 118
Compressors and pneumatic tools, machines and equipment
28
Tokyo (Japan)
TC 59/SC 3
Buildings and civil engineering works/Functional/user requirements and performance in
building construction
29
Berlin (Germany)
TC 117
Fans
April 2011
1
Prague (Czech
Republic)
JTC 1/SC 34
Information technology/Document description and processing languages
2-3
Oostenede
(Belgium)
TC 23/SC 3
Tractors and machinery for agriculture and forestry/Safety and comfort
3-4
Oostenede
(Belgium)
TC 23
Tractors and machinery for agriculture and forestry
4
Urbach
(Germany)
TC 161
Control and protective devices for gas and/or oil burners and appliances
4-5
Madrid (Spain)
TC 34/SC 11
Food products/Animal and vegetable fats and oils
4-7
Berlin (Germany)
TC 127
Earth-moving machinery
6
Madrid (Spain)
TC 34/SC 2
Food products/Oleaginous seeds and fruits and oilseed meals
6
Bratislava
(Slovakia)
TC 226
Materials for the production of primary aluminium
7
London (United
Kingdom)
TC 43/SC 2
Acoustics/Building acoustics
7
Paris (France)
TC 92/SC 1
Fire safety/Fire initiation and growth
7
La Plaine StDenis (France)
TC 92/SC 2
Fire safety/Fire containment
7
Paris (France)
TC 92/SC 3
Fire safety/Fire threat to people and environment
7-8
London (United
Kingdom)
TC 43/SC 1
Acoustics/Noise
8
London (United
Kingdom)
TC 43
Acoustics
8
Paris (France)
TC 92
Fire safety
8
La Plaine StDenis (France)
TC 92/SC 4
Fire safety/Fire safety engineering
8
Delft
(Netherlands)
TC 153/SC 1
Valves/Design, manufacture, marking and testing
10-12
Porto (Portugal)
TC 59/SC 14
Buildings and civil engineering works/Design life
11-12
Tokyo (Japan)
TC 210
Quality management and corresponding general aspects for medical devices
11-15
St-Denis
(France)
JTC 1/SC 38
Information technology/Distributed application platforms and services (DAPS)
11-15
Prague (Czech
Republic)
TC 204
Intelligent transport systems
11-16
Berlin (Germany)
TC 130
Graphic technology
13-14
Dresden
(Germany)
TC 199
Safety of machinery
14
Milan (Italy)
TC 8/SC 12
Ships and marine technology/Ships and marine technology - Large yachts
15
Porto (Portugal)
TC 23/SC 7
Tractors and machinery for agriculture and forestry/Equipment for harvesting and
conservation
18-19
Singapore
(Singapore)
JTC 1/SC 27
Information technology/IT Security techniques
19-20
Berlin (Germany)
TC 22/SC 1
Road vehicles/Ignition equipment
20-21
Astana
(Kazakhstan)
TC 67/SC 6
Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries/Processing equipment and systems
26-29
Niagara Falls
(Canada)
TC 85/SC 2
Nuclear energy, nuclear technologies, and radiological protection/Radiological protection
27-28
Delft
(Netherlands)
TC 24/SC 4
Particle characterization including sieving/Particle characterization
*
*
**
May 2011
2-3
Paris (France)
TC 155
Nickel and nickel alloys
2-4
The Hague
(Netherlands)
TC 249
Traditional chinese medicine
2-6
Sydney
(Australia)
TC 46
Information and documentation
3-4
Paris (France)
TC 44/SC 3
Welding and allied processes/Welding consumables
4-5
Geneva
(Switzerland)
TC 94
Personal safety -- Protective clothing and equipment
6-13
Geneva
(Switzerland)
TC 94/SC 14
Personal safety -- Protective clothing and equipment/Fire-fighters' personal equipment
9
Amsterdam
TC 68/SC 2
Financial services/Security management and general banking operations
(Netherlands)
9
Amsterdam
(Netherlands)
9
*
TC 68/SC 4
Financial services/Securities and related financial instruments
Berlin (Germany)
TC 110/SC 1
Industrial trucks/General terminology
9-13
Berlin (Germany)
TC 114
Horology
9-13
Adelaide
(Australia)
TC 241
Project Committee: Road-Traffic Safety Management System
11
Berlin (Germany)
TC 110/SC 4
Industrial trucks/Rough-terrain trucks
11
Porto de
Galinhas (Brazil)
TC 135/SC 9
Non-destructive testing/Acoustic emission testing
12
Delft
(Netherlands)
TC 68
Financial services
12
Berlin (Germany)
TC 110/SC 2
Industrial trucks/Safety of powered industrial trucks
12-13
Florida (USA)
TC 184/SC 5
Automation systems and integration/Interoperability, integration, and architectures for
enterprise systems and automation applications
12-13
Vienna (Austria)
TC 253
Project committee: Treated wastewater re-use for irrigation
13
Franklin Lakes
(USA)
TC 84
Devices for administration of medicinal products and intravascular catheters
13
Berlin (Germany)
TC 110
Industrial trucks
13
Beijing (China)
TC 195
Building construction machinery and equipment
16-17
Bratislava
(Slovakia)
TC 44/SC 11
Welding and allied processes/Qualification requirements for welding and allied
processes personnel
16-19
Kobe (Japan)
TC 22/SC 13
Road vehicles/Ergonomics applicable to road vehicles
16-19
Stockholm
(Sweden)
**
TC 156
Corrosion of metals and alloys
16-20
Kona, Hawaii
(USA)
*
JTC 1/SC 32
Information technology/Data management and interchange
16-20
Zurich
(Switzerland)
TC 39/SC 2
Machine tools/Test conditions for metal cutting machine tools
16-20
Beijing (China)
TC 247
Fraud countermeasures and controls
16-20
Berlin (Germany)
TC 248
Project committee: Sustainability criteria for bioenergy
16-22
Vienna (Austria)
*
TC 224
Service activities relating to drinking water supply systems and wastewater systems Quality criteria of the service and performance indicators
18
Milan (Italy)
*
TC 131/SC 7
Fluid power systems/Sealing devices
18-19
Bratislava
(Slovakia)
TC 44/SC 10
Welding and allied processes/Unification of requirements in the field of metal welding
18-19
Pau (France)
TC 67/SC 2
Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries/Pipeline transportation systems
19-20
Paris (France)
TC 87
Cork
20
Kobe (Japan)
TC 22/SC 17
Road vehicles/Visibility
20
Viterbo (Italy)
TC 228
Tourism and related services
*
*
*
20
St. Petersburg
(Russian
Federation)
TC 229
Nanotechnologies
22-27
Paris (France)
JTC 1/SC 7
Information technology/Software and systems engineering
22-27
Portland, Oregon
(USA)
*
TC 184/SC 4
Automation systems and integration/Industrial data
23-24
Stavanger
(Norway)
*
TC 67/SC 4
Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries/Drilling and production equipment
23-27
La Plaine StDenis (France)
*
TC 6
Paper, board and pulps
23-27
Chicago (USA)
**
TC 23/SC 6
Tractors and machinery for agriculture and forestry/Equipment for crop protection
23-27
Salt Lake City
(USA)
TC 171
Document management applications
23-27
Kuopio (Finland)
*
TC 215
Health informatics
23-28
Jeju (Korea,
Republic of)
*
TC 147
Water quality
24
Stockholm
(Sweden)
TC 29/SC 2
Small tools/High speed steel cutting tools and their attachments
24-26
St. Petersburg
(Russian
Federation)
TC 67/SC 5
Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries/Casing, tubing and drill pipe
25
Milan (Italy)
TC 136
Furniture
25-27
Salt Lake City
(USA)
TC 171/SC 1
Document management applications/Quality
26
Berlin (Germany)
TC 20/SC 14
Aircraft and space vehicles/Space systems and operations
26
Stockholm
(Sweden)
TC 29/SC 9
Small tools/Tools with cutting edges made of hard cutting materials
26-27
Vienna (Austria)
JTC 1/SC 31
Information technology/Automatic identification and data capture techniques
26-27
Delft
(Netherlands)
TC 211
Geographic information/Geomatics
27
Stockholm
(Sweden)
TC 29
Small tools
31
Pretoria (South
Africa)
TC 96/SC 7
Cranes/Tower cranes
*
*
May-June 2011
30-1
Pretoria (South
Africa)
TC 96/SC 6
Cranes/Mobile cranes
30-3
Berlin (Germany)
TC 223
Societal Security
31-2
London (United
Kingdom)
TC 85/SC 5
Nuclear energy, nuclear technologies, and radiological protection/Nuclear fuel cycle
31-1
Beijing (China)
TC 257
Energy savings
TC 96/SC 4
Cranes/Test methods
*
June 2011
1
Pretoria (South
Africa)
*
1
Pretoria (South
Africa)
TC 96/SC 8
Cranes/Jib cranes
2
Pretoria (South
Africa)
TC 96/SC 5
Cranes/Use, operation and maintenance
3
Pretoria (South
Africa)
TC 96/SC 3
Cranes/Selection of wire ropes
3
Pretoria (South
Africa)
TC 96/SC 9
Cranes/Bridge and gantry cranes
4
Pretoria (South
Africa)
TC 96
Cranes
4
Pretoria (South
Africa)
*
TC 96/SC 2
Cranes/Terminology
4
Pretoria (South
Africa)
*
TC 96/SC 10
Cranes/Design principles and requirements
6
Vienna (Austria)
TC 145/SC 1
Graphical symbols/Public information symbols
6-10
Rochester (USA)
TC 42
Photography
7
Vienna (Austria)
TC 145/SC 2
Graphical symbols/Safety identification, signs, shapes, symbols and colours
7
Vienna (Austria)
TC 145/SC 3
Graphical symbols/Graphical symbols for use on equipment
8
Cannes (France)
TC 35/SC 12
Paints and varnishes/Preparation of steel substrates before application of paints and
related products
8
Cannes (France)
TC 35/SC 14
Paints and varnishes/Protective paint systems for steel structures
8
Vienna (Austria)
TC 145
Graphical symbols
9
Düsseldorf
(Germany)
TC 17/SC 15
Steel/Railway rails and their fasteners
9
Cannes (France)
TC 35/SC 9
Paints and varnishes/General test methods for paints and varnishes
9-10
Vienna (Austria)
TC 91
Surface active agents
10
Helsinki
(Finland)
JTC 1/SC 2
Information technology/Coded character sets
10
Cannes (France)
**
TC 35
Paints and varnishes
10
Vancouver
(Canada)
**
TC 192
Gas turbines
12-17
Seoul (Korea,
Republic of)
*
TC 37
Terminology and other language and content resources
13-17
Brussels
(Belgium)
*
TC 4
Rolling bearings
13-17
Tokyo (Japan)
*
TC 69
Applications of statistical methods
13-17
Vancouver
(Canada)
TC 121
Anaesthetic and respiratory equipment
13-17
Vancouver
(Canada)
TC 121/SC 3
Anaesthetic and respiratory equipment/Lung ventilators and related equipment
13-17
Vancouver
(Canada)
**
TC 121/SC 6
Anaesthetic and respiratory equipment/Medical gas systems
13-18
Vancouver
(Canada)
*
TC 121/SC 2
Anaesthetic and respiratory equipment/Airways and related equipment
*
*
*
14-15
Milan (Italy)
TC 17/SC 17
Steel/Steel wire rod and wire products
14-15
Geneva
(Switzerland)
TMB
Technical Management Board
15
Stockholm
(Sweden)
TC 29/SC 5
Small tools/Grinding wheels and abrasives
15-17
Kobe (Japan)
TC 8/SC 1
Ships and marine technology/Lifesaving and fire protection
16
London (United
Kingdom)
TC 51
Pallets for unit load method of materials handling
20-21
Düsseldorf
(Germany)
TC 167
Steel and aluminium structures
20-21
Milan (Italy)
TC 252
Project committee: Natural gas fuelling stations for vehicles
20-22
Bournemouth
(United
Kingdom)
TC 34/SC 9
Food products/Microbiology
20-24
Pretoria (South
Africa)
TC 137
Footwear sizing designations and marking systems
21
Berlin (Germany)
*
TC 10/SC 1
Technical product documentation/Basic conventions
22
Berlin (Germany)
*
TC 10/SC 6
Technical product documentation/Mechanical engineering documentation
22
Berlin (Germany)
TC 10/SC 10
Technical product documentation/Process plant documentation and tpd-symbols
23
Berlin (Germany)
TC 10
Technical product documentation
24
San Diego (USA)
JTC 1/SC 6
Information technology/Telecommunications and information exchange between
systems
26-30
Hollywood,
Florida (USA)
*
TC 85/SC 6
Nuclear energy, nuclear technologies, and radiological protection/Reactor technology
27-29
Winterthur
(Switzerland)
*
TC 21/SC 5
Equipment for fire protection and fire fighting/Fixed firefighting systems using water
27-29
Washington, D.C
(USA)
TC 258
Project, programme and portfolio management
27-30
Suresnes
(France)
TC 20/SC 1
Aircraft and space vehicles/Aerospace electrical requirements
29
Berlin (Germany)
*
TC 44/SC 6
Welding and allied processes/Resistance welding and allied mechanical joining
29-30
London (United
Kingdom)
**
TC 29/SC 10
Small tools/Assembly tools for screws and nuts, pliers and nippers
San Francisco
(USA)
**
TC 67/SC 3
Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries/Drilling and completion fluids, and well cements
Hong Kong
(Hong Kong,
China)
**
TC 71
Concrete, reinforced concrete and pre-stressed concrete
(South Africa)
**
TC 133
Sizing systems and designations for clothes
TC 94/SC 6
Personal safety -- Protective clothing and equipment/Eye and face protection
TC 188
Small craft
TC 22/SC 3
Road vehicles/Electrical and electronic equipment
*
*
June-July 2011
27-1
Berlin (Germany)
27-1
Paris (France)
30-1
Pisa (Italy)
**
July 2011
1
Oslo (Norway)
11-15
Delft
(Netherlands)
24
Turin (Italy)
TC 207
Environmental management
*
REMCO
Committee on reference materials
*
JTC 1/SC 29
Information technology/Coding of audio, picture, multimedia and hypermedia information
*
JTC 1/SC 35
Information technology/User interfaces
August-September 2011
29-2
Warsaw (Poland)
September 2011
9-15
Chicago (USA)
**
TC 163
Thermal performance and energy use in the built environment
12-14
Chicago (USA)
*
TC 205
Building environment design
12-16
Vienna (Austria)
*
TC 108/SC 4
Mechanical vibration, shock and condition monitoring/Human exposure to mechanical
vibration and shock
12-16
Florianopolis
(Brazil)
**
TC 150
Implants for surgery
12-16
Florianopolis
(Brazil)
*
TC 150/SC 1
Implants for surgery/Materials
12-16
Rotorua (New
Zealand)
*
TC 218
Timber
13-15
Moscow
(Russian
Federation)
*
TC 67
Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries
15-17
Brescia (Italy)
**
TC 201
Surface chemical analysis
15-22
Beijing (China)
**
TC 213
Dimensional and geometrical product specifications and verification
18-24
Phoenix (USA)
TC 106
Dentistry
18-24
Paris (France)
*
TC 164
Mechanical testing of metals
19
Chicago (USA)
*
TC 21/SC 3
Equipment for fire protection and fire fighting/Fire detection and alarm systems
19
Chicago (USA)
*
TC 21/SC 11
Equipment for fire protection and fire fighting/Smoke and heat control systems and
components
19-20
Paris (France)
*
TC 164/SC 3
Mechanical testing of metals/Hardness testing
19-20
New Delhi (India)
*
TMB
Technical Management Board
19-22
Paris (France)
*
TC 164/SC 4
Mechanical testing of metals/Toughness testing -- Fracture (F), Pendulum (P), Tear (T)
19-23
Seoul (Korea,
Republic of)
*
JTC 1/SC 38
Information technology/Distributed application platforms and services (DAPS)
19-23
Bali (Indonesia)
*
TC 165
Timber structures
19-23
Adelaide
(Australia)
*
TC 190
Soil quality
19-23
Adelaide
(Australia)
*
TC 190/SC 1
Soil quality/Evaluation of criteria, terminology and codification
19-23
Adelaide
(Australia)
*
TC 190/SC 3
Soil quality/Chemical methods and soil characteristics
19-23
Adelaide
(Australia)
*
TC 190/SC 4
Soil quality/Biological methods
19-23
Adelaide
(Australia)
*
TC 190/SC 7
Soil quality/Soil and site assessment
20
Chicago (USA)
**
TC 21/SC 6
Equipment for fire protection and fire fighting/Foam and powder media and fixed
firefighting systems using foam and powder
20
Berlin (Germany)
*
TC 29/SC 8
Small tools/Tools for pressing and moulding
20-22
Paris (France)
*
TC 164/SC 5
Mechanical testing of metals/Fatigue testing
20-23
Washington, D.C
(USA)
**
TC 172/SC 5
Optics and photonics/Microscopes and endoscopes
21
Chicago (USA)
*
TC 21/SC 2
Equipment for fire protection and fire fighting/Manually transportable fire extinguishers
21
Vienna (Austria)
*
TC 146/SC 6
Air quality/Indoor air
21
Paris (France)
*
TC 164/SC 2
Mechanical testing of metals/Ductility testing
21-22
Chicago (USA)
*
TC 21/SC 8
Equipment for fire protection and fire fighting/Gaseous media and firefighting systems
using gas
21-23
New Delhi (India)
**
GA
General Assembly
22
Sao Paulo
(Brazil)
*
TC 142
Cleaning equipment for air and other gases
22-23
Las Vegas
(USA)
TC 159/SC 4
Ergonomics/Ergonomics of human-system interaction
22-23
Paris (France)
*
TC 164/SC 1
Mechanical testing of metals/Uniaxial testing
23
Chicago (USA)
*
TC 21
Equipment for fire protection and fire fighting
24
New Delhi (India)
*
COUNCIL
Council
26-27
Geneva
(Switzerland)
*
TAG 8
Building
26-27
La Plaine StDenis (France)
TC 206
Fine ceramics
Shanghai
(China)
**
JTC 1/SC 36
Information technology/Information technology for learning, education and training
Edinburgh
(United
Kingdom)
**
TC 24/SC 4
Particle characterization including sieving/Particle characterization
(Unknown)
**
TC 44/SC 9
Welding and allied processes/Health and safety
London (United
Kingdom)
**
TC 59/SC 2
Buildings and civil engineering works/Terminology and harmonization of languages
(France)
**
TC 59/SC 8
Buildings and civil engineering works/Sealants
(Malaysia)
**
TC 61/SC 4
Plastics/Burning behaviour
(United
Kingdom)
**
TC 41/SC 1
Pulleys and belts (including veebelts)/Friction
(United
Kingdom)
**
TC 41/SC 3
Pulleys and belts (including veebelts)/Conveyor belts
(United
Kingdom)
**
TC 41/SC 4
Pulleys and belts (including veebelts)/Synchronous belt drives
Sapporo (Japan)
**
TC 184/SC 1
Automation systems and integration/Physical device control
3rd Quarter 2011
Mexico (Mexico)
**
TC 253
Project committee: Treated wastewater re-use for irrigation
October 2011
3-7
Sydney
(Australia)
*
TC 89
Wood-based panels
3-7
London (United
Kingdom)
*
TC 146/SC 2
Air quality/Workplace atmospheres
6-7
Geneva
(Switzerland)
*
CASCO
Committee on conformity assessment
9-14
Beijing (China)
*
TC 27
Solid mineral fuels
10-14
(Unknown)
**
TC 25
Cast irons and pig irons
10-14
(Japan)
**
TC 34/SC 17
Food products/Management systems for food safety
10-14
Nanjing (China)
**
TC 193/SC 1
Natural gas/Analysis of natural gas
10-14
Tampa, Florida
(USA)
*
TC 204
Intelligent transport systems
10-14
Milan (Italy)
*
TC 209
Cleanrooms and associated controlled environments
16-21
Suzhou (China)
*
TC 184/SC 4
Automation systems and integration/Industrial data
17-19
Tokyo (Japan)
*
TC 5/SC 2
Ferrous metal pipes and metallic fittings/Cast iron pipes, fittings and their joints
17-20
Yokohama
(Japan)
*
TC 45/SC 2
Rubber and rubber products/Testing and analysis
17-21
Berlin (Germany)
*
TC 2
Fasteners
17-21
Berlin (Germany)
*
TC 2/SC 7
Fasteners/Reference standards
17-21
Berlin (Germany)
*
TC 2/SC 11
Fasteners/Fasteners with metric external thread
17-21
Berlin (Germany)
*
TC 2/SC 12
Fasteners/Fasteners with metric internal thread
17-21
Berlin (Germany)
*
TC 2/SC 13
Fasteners/Fasteners with non-metric thread
17-21
Berlin (Germany)
*
TC 2/SC 14
Fasteners/Surface coatings
17-21
Yokohama
(Japan)
*
TC 45
Rubber and rubber products
18-20
London (United
Kingdom)
*
TC 202
Microbeam analysis
21
Courbevoie,
Paris (France)
*
TC 244
Industrial furnaces and associated processing equipment
24-28
Tokyo (Japan)
TC 38
Textiles
24-28
Tokyo (Japan)
TC 38/SC 2
Textiles/Cleansing, finishing and water resistance tests
24-28
Tokyo (Japan)
TC 38/SC 20
Textiles/Fabric descriptions
24-28
Tokyo (Japan)
TC 38/SC 23
Textiles/Fibres and yarns
24-28
Tokyo (Japan)
TC 38/SC 24
Textiles/Conditioning atmospheres and physical tests for textile fabrics
24-28
Moscow
(Russian
Federation)
**
TC 178
Lifts, escalators and moving walks
24-29
Beijing (China)
*
TC 176
Quality management and quality assurance
25-27
Beltsville,
Maryland (USA)
*
TC 34/SC 16
Food products/Horizontal methods for molecular biomarker analysis
25-28
Amsterdam
(Netherlands)
**
TC 138/SC 1
Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for
soil, waste and drainage (including land drainage)
26
Amsterdam
(Netherlands)
*
TC 138/SC 2
Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for
water supplies
26
Amsterdam
(Netherlands)
**
TC 138/SC 4
Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for
the supply of gaseous fuels
27
Amsterdam
(Netherlands)
**
TC 138/SC 3
Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for
industrial applications
27-28
(Europe)
**
TC 44
Welding and allied processes
(Korea, Republic
of)
**
JTC 1/SC 17
Information technology/Cards and personal identification
London (United
Kingdom)
**
TC 59/SC 15
Buildings and civil engineering works/Performance criteria for single family attached and
detached dwellings
(China)
**
TC 111
Round steel link chains, chain slings, components and accessories
(China)
**
TC 111/SC 1
Round steel link chains, chain slings, components and accessories/Chains and chain
slings
(China)
**
TC 111/SC 3
Round steel link chains, chain slings, components and accessories/Components and
accessories
(Netherlands)
**
TC 138
Plastics pipes, fittings and valves for the transport of fluids
Amsterdam
(Netherlands)
**
TC 138/SC 5
Plastics pipes, fittings and valves for the transport of fluids/General properties of pipes,
fittings and valves of plastic materials and their accessories -- Test methods and basic
specifications
Vienna (Austria)
**
TC 146/SC 1
Air quality/Stationary source emissions
Berlin (Germany)
**
TC 160/SC 1
Glass in building/Product considerations
**
TC 46/SC 11
Information and documentation/Archives/records management
October-November 2011
31-3
London (United
Kingdom)
November 2011
2-4
Bangkok
(Thailand)
*
TC 123
Plain bearings
2-4
Bangkok
(Thailand)
*
TC 123/SC 2
Plain bearings/Materials and lubricants, their properties, characteristics, test methods
and testing conditions
2-4
Bangkok
(Thailand)
*
TC 123/SC 3
Plain bearings/Dimensions, tolerances and construction details
2-4
Bangkok
(Thailand)
*
TC 123/SC 5
Plain bearings/Quality analysis and assurance
2-4
Bangkok
(Thailand)
*
TC 123/SC 6
Plain bearings/Terms and common items
2-4
Bangkok
(Thailand)
*
TC 123/SC 7
Plain bearings/Special types of plain bearings
4
Cincinnati (USA)
*
TC 60
Gears
4
(Malaysia)
**
TC 238
Solid biofuels
7-11
Osaka (Japan)
**
TC 94/SC 13
Personal safety -- Protective clothing and equipment/Protective clothing
7-12
(USA)
*
JTC 1
Information technology
10
Annapolis (USA)
*
TC 70/SC 7
Internal combustion engines/Tests for lubricating oil filters
10-11
Venice (Italy)
*
TC 227
Springs
14-16
Nagoya (Japan)
**
TC 189
Ceramic tile
14-18
(South Africa)
**
TC 229
Nanotechnologies
17
Munich
(Germany)
*
TC 44/SC 12
Welding and allied processes/Soldering materials
21-22
Berlin (Germany)
*
TC 44/SC 8
Welding and allied processes/Equipment for gas welding, cutting and allied processes
21-25
Stellenbosch
(South Africa)
**
TC 98
Bases for design of structures
(Unknown)
**
TC 34/SC 7
Food products/Spices, culinary herbs and condiments
(Japan)
**
TC 38/SC 24
Textiles/Conditioning atmospheres and physical tests for textile fabrics
Pau (France)
**
TC 67/SC 3
Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries/Drilling and completion fluids, and well cements
November-December 2011
26-1
(Israel)
**
TC 23/SC 18
Tractors and machinery for agriculture and forestry/Irrigation and drainage equipment
and systems
*
TC 108/SC 5
Mechanical vibration, shock and condition monitoring/Condition monitoring and
diagnostics of machines
(USA)
**
TC 30/SC 7
Measurement of fluid flow in closed conduits/Volume methods including water meters
(Japan)
**
TC 172/SC 3
Optics and photonics/Optical materials and components
(South Africa)
**
TC 211
Geographic information/Geomatics
**
TC 130
Graphic technology
(North America)
**
JTC 1/SC 24
Information technology/Computer graphics, image processing and environmental data
representation
Kyoto (Japan)
**
TC 33
Refractories
**
TC 213
Dimensional and geometrical product specifications and verification
December 2011
5-9
Sydney
(Australia)
4th Quarter 2011
2nd Semester 2011
Tokyo (Japan)
Month unknown 2011
January 2012
Charlotte (USA)
February 2012
20-24
Kyoto (Japan)
*
JTC 1/SC 35
Information technology/User interfaces
22-23
Geneva
(Switzerland)
*
TMB
Technical Management Board
Florida (USA)
**
TC 115
Pumps
(USA)
**
TC 184/SC 2
Automation systems and integration/Robots and robotic devices
**
TC 34/SC 12
Food products/Sensory analysis
(Unknown)
**
TC 23/SC 19
Tractors and machinery for agriculture and forestry/Agricultural electronics
(China)
**
JTC 1/SC 6
Information technology/Telecommunications and information exchange between
systems
(Australia)
**
JTC 1/SC 36
Information technology/Information technology for learning, education and training
(Korea, Republic
of)
**
JTC 1/SC 36
Information technology/Information technology for learning, education and training
(Italy)
**
TC 172/SC 7
Optics and photonics/Ophthalmic optics and instruments
February-March 2012
25-5
Toulouse
(France)
March 2012
29
April 2012
11-12
(Finland)
**
TC 117
Fans
16-20
Durban (South
Africa)
**
TC 135
Non-destructive testing
Bern
(Switzerland)
**
TC 113
Hydrometry
Durban (South
Africa)
**
TC 135/SC 3
Non-destructive testing/Ultrasonic testing
Durban (South
Africa)
**
TC 135/SC 5
Non-destructive testing/Radiation methods
May 2012
7-11
Berlin (Germany)
**
TC 46
Information and documentation
10
Chicago (USA)
**
TC 68
Financial services
(Unknown)
**
JTC 1/SC 38
Information technology/Distributed application platforms and services (DAPS)
(Unknown)
**
TC 126
Tobacco and tobacco products
June 2012
6-7
Geneva
(Switzerland)
**
COPOLCO
Committee on consumer policy
13-14
Geneva
(Switzerland)
*
TMB
Technical Management Board
Calgary
(Canada)
**
TC 67/SC 3
Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries/Drilling and completion fluids, and well cements
**
TC 211
Geographic information/Geomatics
**
JTC 1/SC 35
Information technology/User interfaces
**
TC 142
Cleaning equipment for air and other gases
2nd Quarter 2012
(France)
August 2012
27-31
Montreal
(Canada)
September 2012
3-8
Zurich
(Switzerland)
19-21
San Diego (USA) **
GA
General Assembly
22
San Diego (USA) **
COUNCIL
Council
Zibo city (China)
**
TC 206
Fine ceramics
Cadiz (Spain)
**
TC 213
Dimensional and geometrical product specifications and verification
Sydney
(Australia)
**
TC 138/SC 4
Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for
the supply of gaseous fuels
(Unknown)
**
JTC 1/SC 38
Information technology/Distributed application platforms and services (DAPS)
**
TC 17/SC 1
Steel/Methods of determination of chemical composition
**
TC 211
Geographic information/Geomatics
(Europe)
**
JTC 1/SC 24
Information technology/Computer graphics, image processing and environmental data
representation
Vienna (Austria)
**
REMCO
Committee on reference materials
Delft
(Netherlands)
**
TC 23/SC 6
Tractors and machinery for agriculture and forestry/Equipment for crop protection
(Unknown)
**
TC 34
Food products
Chicago (USA)
**
TC 68/SC 4
Financial services/Securities and related financial instruments
(South Africa)
**
TC 102
Iron ore and direct reduced iron
Berlin (Germany)
**
TC 107
Metallic and other inorganic coatings
Sydney
(Australia)
**
TC 138
Plastics pipes, fittings and valves for the transport of fluids
Sydney
(Australia)
**
TC 138/SC 1
Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for
soil, waste and drainage (including land drainage)
(Unknown)
**
TC 146
Air quality
(Brazil)
**
TC 164
Mechanical testing of metals
(Finland)
**
TC 190
Soil quality
(China)
**
TC 202
Microbeam analysis
(France)
**
TC 205
Building environment design
(Thailand)
**
TC 207
Environmental management
**
JTC 1/SC 35
Information technology/User interfaces
October 2012
24
November 2012
Tokyo (Japan)
4th Quarter 2012
(Saudi Arabia)
Month unknown 2012
February-March 2013
25-1
(South America)
March 2013
(Kenya)
**
JTC 1/SC 36
Information technology/Information technology for learning, education and training
**
JTC 1/SC 35
Information technology/User interfaces
(Korea, Republic
of)
**
TC 123/SC 2
Plain bearings/Materials and lubricants, their properties, characteristics, test methods
and testing conditions
(Korea, Republic
of)
**
TC 123/SC 3
Plain bearings/Dimensions, tolerances and construction details
(Korea, Republic
of)
**
TC 123/SC 5
Plain bearings/Quality analysis and assurance
(Korea, Republic
of)
**
TC 123/SC 6
Plain bearings/Terms and common items
(Korea, Republic
of)
**
TC 123/SC 7
Plain bearings/Special types of plain bearings
Tokyo (Japan)
**
TC 142
Cleaning equipment for air and other gases
**
TC 113
Hydrometry
(USA)
**
REMCO
Committee on reference materials
(Unknown)
**
TC 38/SC 1
Textiles/Tests for coloured textiles and colorants
(Norway)
**
TC 138/SC 1
Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for
soil, waste and drainage (including land drainage)
**
TC 142
Cleaning equipment for air and other gases
**
TC 142
Cleaning equipment for air and other gases
August 2013
26-30
(South America)
September 2013
October 2013
Mexico (Mexico)
Month unknown 2013
Month unknown 2014
(USA)
Month unknown 2015
London (United
Kingdom)