Urea-2010

advertisement
MATERIAL SAFETY DATA SHEET
Revision 08/01/10
Page 1 of 3
PLASTIC BLAST MEDIA
TYPE UF (UREA)
1. PRODUCTION NAME AND COMPANY IDENTIFICATION
Product Name:
Abrasive Supply Co., Inc. Plant Media Type UF
Chemical Family:
Thermoset Plastics
Chemical Name:
Thermoset Urea Formaldehyde Plastic
CAS Registry
90011-05-06
MANUFACTURER:
Abrasive Supply Co., Inc.
Phone: (330) 894-2818
25240 State Route 172
Fax:
(330) 894-2626
Minerva, OH 44657
Email: sales@polyblast.com
=====================================================================
2. COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients
Polymerized Urea Molding Compound
CAS Registry No. 9011-05-6
%Wt.
97
Exposure Limits
ACGIH TLV None
OSHA PEL None
2
ACGIH TLV None
OSHA PEL None
Pigment and additives
Anti Stat Agent
1
ACGIH TLV None
CAS Registry No. 002764-13-8
OSHA PEL None
==================================================================================
3. HAZARDS IDENTIFICATION
Overview
Material is granular. Odorless particles of one or several colors. Avoid creating airborne dust
Avoid ignition sources. Provide ventilation. Avoid breathing dust, or contact with eyes or skin.
Spilled material can be slippery and cause falls if walked on.
HMIS
Health
Flammability
Reactivity
Potential Health Effect
Inhalation:
Skin contact:
Eye contact:
Ingestion:
Carcinogenicity
NTP:
No
IARC Monographs: No
OSHA: No
2
0
0
NFPA
2
0
0
Potential respiratory tract irritation
Potential slight irritation
Potential irritation
May be harmful if swallowed
HMIS
Health
2
Flammability 0
Reactivity
0
NFPA
2
0
0
TYPE UF (UREA) – MSDS – ABRASIVE SUPPLY CO., INC. 25240 State Route 172 Minerva, OH 44657
Page 2 of 3
4. FIRST AID PROCEDURES
Inhalation:
Skin Contact:
Eye Contact
Ingestion:
Remove to uncontaminated area, provide fresh air.
Call physician if irritation persists.
Wash thoroughly with soap and water. Consult a physician
if irritation develops.
Flush with water for 15 minutes. Consult a physician if
irritation develops.
Immediately induce vomiting by giving two glasses of water.
Call physician
5. FIRE FIGHTING MEASURES
Flash Point (Method Used):
Extinguishing media:
Special Fire Fighting Procedure:
Unusual Fire & Explosion:
Flammable Limits, N/A
NA
Carbon dioxide, foam, dry chemicals, or water fog
Wear full protective clothing, and self contained
breathing device with full face mask.
None, dust can form explosive mixture with air.
LEL: N/A
UEL: N/A
6. ACCIDENTAL RELEASE MEASURES
Note: Review sections 5 and 8 before proceeding. Eliminate flames, sparks, excessive temperatures,
and oxidizing agents. Sweep up and place in waste container.
7. HANDLING AND STORAGE
Store in closed properly labeled containers in a cool, ventilated area .
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Avoid creating airborne dust. Local exhaust recommended to keep airborne dust below OSHA requirements.
Mechanical ventilation suggested, use explosion proof electrical equipment for very high dust
levels. Provide protective gloves. Wear goggles and face shield for eye protection. Recommend
3M #8710 Dust and Mist Respirator for respiratory protection. Wash thoroughly before eating and
when finished. Launder work clothes between each use. If necessary wear TYVEC protective suit with hood.
9. PHYSICAL AND CHEMICAL PROPERTIES
Boiling point (F)
Vapor Pressure (mmHg):
Solubility in water:
pH:
Odor:
Appearance:
Color:
Specific gravity (H20=1)
Melting point:
Evaporation rate:
N/A
N/A
Insoluble
4.0-8.0
Odorless
Granulate, one of several colors
One or several
1.5
N/A
N/A
10. STABILITY AND REACTIVITY
Stability
Incompatibility (material to avoid):
Hazardous Decomposition Products:
Hazardous Polymerization
Stable
None known
Smoke, carbon monoxide, nitrous oxide
Will not occur
TYPE UF (UREA) – MSDS – ABRASIVE SUPPLY CO., INC. 25240 State Route 172 Minerva, OH 44657
Page 3 of 3
11. TOXICOLOGICAL INFORMATION
Very low order of acute toxicity
======================================================================================
12. ECOLOGICAL INFORMATION
Cleaned up material is not known to pose any significant ecological problems. Always comply with Federal,
State and Local environmental regulations.
13. DISPOSAL CONSIDERATIONS
Dispose as solid waste in sanitary landfill according to Federal, State and Local regulations. Observe all
applicable Federal, State and Local environmental regulations.
14. TRANSPORTATION INFORMATION
DOT:
Proper Shipping Name:
Tariff No.
NMF Classification – Class 60
Not regulated
Plastic Material, Granules
156200
156200
15. REGULATORY INFORMATION
Review OSHA Std., for PPE in 29 CFR 1910 Subpart I to ensure proper use for any applicable PPE.
16. OTHER INFORMATION
The above information is believed to be correct but does not purport to be all inclusive and shall be used only
as a guide. Abrasive Supply Co., Inc. shall not be held liable for any damage resulting from handling or from
contact with the above product.
License granted to make unlimited paper copies for internal use only.
Download