Multi-Function Beauty System USER MANUAL
B-8618-33
MULTI-FUCTION BEAUTY SYSTEM
Facial Steamer with timer, High frequency, Galvanic, Rotary brush, Skin
lifting,
Vacuum/Spray,
Ultrasonic
Scrubber ， Ultrasonic,
Diamond
Microdamabration, Metabolic depressor, Remove spot, Bust vacuum
massager, Wood lamp, Magnifying lamp.
……………………………………………………………….
………………………………………………………………
1
Multi-Function Beauty System USER MANUAL
Installation diagram
……………………………………………………………….
………………………………………………………………
2
Multi-Function Beauty System USER MANUAL
Facial Steamer with Ozone
The facial steamer is used to clean the skin thoroughly by opening the pores in order
to remove impurities (like blackheads, whiteheads, make up, etc.) and generally
revitalize the skin. The addition of ozone enriched steam helps to promote a more sterile
environment for further treatment of the skin.
High Frequency
High frequency provides germicidal, decongesting effect and can produce ozone that
helps to cure wound easily without leaving any pitted scar. It provides accurate
intensity adjustment; and handle with spiral cable for better mobility. This machine
comes with both ultra violet and infrared electrodes in order to suit any skin types.
Galvanic
Galvanic is for deep cleaning. Introduction of active substance by means of galvanic
current which helps to permeate the layers of skin much more intensively and deeply
than with manual application.
Skin Lifting
Lifting uses positive and negative electrical current to improve blood circulations,
skin elasticity in order to tighten skin texture and distance between skin cells.
Visible dramatic result is revealed.
Vacuum & Spray
Vacuum suction treatments are for reshaping the body and removing blackheads and
impurities from skin. The suction cup/tube is attached to the unit and the pressure
controls allow the esthetician to vary the strength of the suction action. The movement
is rhythmic stroke toward lymph nodes.
Usually this procedure is used on the face, thighs, hips, arms and abdomen areas. The
movement hastens removal of waste products and inverse pressure causes subcutaneous
tissue to lift or arch to fill the cavity of the cup attachment creating an erythematic
and stimulating effect on the tissue.
Rotary Brush
Rotary brush is able to massage the skin while it deep cleanses skin surface. It can
be used on different face and body parts, especially on rough skin. Deep cleanses
impurities away from skin surface and pores. Performs rhythmic and vibrating massage
in order to relief stressed and tired skin. It also helps to accelerate and improve
blood circulations and metabolism. Client will feel refreshed and relax; and it leaves
skin soft and smooth.
Ultrasonic
Ultrasonic allows fast and visible result with deep penetrations. It is easy to use
and contains lots of different functions in order to suit any skin types or problems.
It stimulates skin without pain and the risk of high voltage burn.
Functions:
……………………………………………………………….
………………………………………………………………
3
Multi-Function Beauty System USER MANUAL
1. De-pigmentation & whitening: ultrasonic can penetrate serums into skin deeply in
order to let skin have a better absorption to enhance and accelerate the result.
2. Reduce redness: use the pulsation frequency in Ultrasonic can improve and accelerate
metabolisms of the capillaries in order to reduce redness.
3. Reduce appearance of scars: Ultrasonic can produce real fast pulsation frequency;
such vibration can help accelerate the disappearance of scars.
4. Moisturizes & hydrates: ultrasonic deeply penetrates serums into skin in order to
let skin have a better absorption to improve hydration of skin.
5. Reduce appearance of dark circles & puffiness: ultrasonic can produce real fast
pulsation frequency; such vibration can help accelerate metabolism and blood
circulations around the eyes. It helps to reduce appearance of dark circles and excess
water, which forms puffiness underneath the eyes.
6. Sterilizations: ultrasonic can push the PH balance towards base in order to increase
power of sterilization. It helps eliminate the growth of bacteria and infections.
7. Relax & reduce pain: the warmth from Ultrasonic helps to calm, relax and reduce pain.
THEORY OF VACUUM
Diamond microdamabration:
Diamond peeling exfoliates your skin by utilizing a multi-degree diamond tipped want
through continuous scrubbing and vacuuming the topmost layer of skin. Skin resurfacing
in such a non-invasive and physical way is mild; simply by selecting the grit size and
the vacuum pressure to determine the degree of abrasion. Diamond Microdermabrasion works
for different skin type even the most sensitive skin and is regarded as being gentler
than chemical exfoliation. It leaves out the problems of broken skin, pigmentation or
redness that is normally found when using acid peels. There are no crystals or abrasives
to contaminate your environment during treatment.
Functions:
1. Recuperate the skin quality and rebuild the health skin;
2. Improve the aging cutis, coarse and aging skin,
3. Improve the detailed line of skin and lax phenomenon,
4. Desalinize spot;
5. Improve thick of pore, small pox scar and concave hole;
6. Stimulate the blood circulation and metabolism;
7. There is no irritating, no shouting pain, no need anaesthetize;
8. Suitable for various kinds of skin, the sensitive skin can be done too;
9. With rubbing the peel of physics machinery type, can control freely;
10. Can see the result at once;
11. Recover fast, one cycle is about 5-7days;
12. Will not influence the work and social activity after treatment.
METABOLIC DEPRESSOR
Cupping massage is in cordinance with what the skin surface is like as a reflection
of the states that the body is in. By stimulating the tissues beneath the skin, you
are increasing blood supply to the treatment area and therefore, improving circulation
and brings the skins temperature to a balance. Aroma therapy for instance, where lotions
are applied to the treatment area to attain a mixture of rapid and slow movement to
……………………………………………………………….
………………………………………………………………
4
Multi-Function Beauty System USER MANUAL
improve and accelerate blood circulation. Results of all this will be improved skin
condition and decreased cellulites.
STATES OF CUPPINJG
By taking advantage over sucking equipments (e. g. a cupping’s cup) we can perform
pulling and releasing movements to the skin achieving what’s called a massage action.
Briefing of such massage method is as below.
1. Gently place the cup over the top of the treatment area using the machine’s pulling
action to pull the skin upwards causing the liquid between the muscle and the cells
to change which then effects the skin’s temperature.
2. When muscle is pulled upwards, cellulites will start to alter along with the muscle.
At this time movement of the muscle will trigger off lymph activities, which then
improves metabolism and gets rid of the toxin inside the body.
3. The pulling action stimulates the patient’s nerve system, which will then give the
patient a relaxed sensation. This system will greatly enhance the results of
therapeutic massage such as foot and acupuncture massage.
THE ADVANTAGES OF THE METABOLIC DEPRESSOR
A. Cotton filters are designed in the handle to enable the use of massage oils other
therapeutic lotions. Also install a glass bottle filters under bottom of machine.
B. Unique design allows extracting the benefits of different lotions and therefore
making this machine user-friendlier for beauticians.
C. Using massage oils or other different therapeutic lotions can have a direct effect
on cellulites.
D. The metabolic depressor has a six stage pulse suction function;
 Visage massage: suitable for patients with allergic skin
 Visage massage: suitable for patients with normal skin
 Body massage1: suitable for areas with little muscle structure such as neck and
shoulder
 Body massage2: rhythmic massage for the larger areas of the back with thicker
muscles
 Breast massage: breast firming and enlargement
 Therapeutic massage: stimulates acupuncture points by using irregular suction
treatment
E. The metabolic depressor provides different levels of intensity for the different
requirements of patients.
F. The metabolic depressor is designed for long-term usage.
ORIGIN OF THE METABOLIC DEPRESSOR
Air-sealed massage first originated from china. By burning off the air inside the cups
on the skin, creating negative pressure. The cup is then moved along the skin to achieve
massage function. Until now, many countries still practices this ancient method of
massaging, and the Metabolic Depressor is based on this ancient method. Combining with
the technology that we have today, we are able to maximize cupping to fullest extent
when it enables us to accurately massage the spot where it is needed according to the
different needs of the clients. The idea that cupping can be done anytime allows for
better scar-removal also.
……………………………………………………………….
………………………………………………………………
5
Multi-Function Beauty System USER MANUAL
Wood Lamp
Wood lamp is to help identify clearly the qualities, problems and the unusual conditions
of the skin; in order to provide proper treatments.
Magnifying Lamp
Magnifying lamp provides cool lighting, which would not sting eyes to make them tired.
It is suitable to be used for special esthetical treatments for precisions.
Special of this system:
Each function in this multi-function beauty system has its own power control. Even if
one function is down, other functions can still be workable.
Specification:
……………………………………………………………….
………………………………………………………………
6
Multi-Function Beauty System USER MANUAL
(1) Switch of Facial steamer
(3) Indicator of functions time
(6) Indicator of H/F.
(9) Indicator of brush
(12) Indicator of Gal/Lifting
(15) Indicator of Ultrasonic
(18,19) Time of Facial steamer.
(21) Suction indicator.
(23) Start/Pause of Vac/Spray.
(25) Start/Pause of brush.
(27) Start/Pause of Gal/Lifting.
(29) Wave of Ultrasonic.
(2) Switch of Facial Ozone
(4,5) Time of functions.
(7,8) Intensity of H/F
(10,11) Intensity of brush
(13,14) Intensity of Gal/Lifting
(16,17) Intensity of Ultrasonic
(20) Power of facial steamer.
(22) Intensity of Vac/Spray.
(24) Start/Pause of H/F.
(26) Select of Gal/Lifting, Gal/Green, Lifting/red.
(28) Start/Pause of Ultrasonic.
(30) Output of Ultrasonic.
Accessories:
High Frequency:
1、H/F Electrode Handle: 1 piece
2、H/F Glass Electrodes: 3 pieces
Ultraviolet
Infrared Indirect massage
Galvanic/Skin Lifting:
1、 Neg. Electrode Cable: 1 piece
2、 Neg. Electrode: 1 piece
3、 Pos. Electrode Cables: 2 pieces
4、 Lifting Electrodes: 2 pieces
5、 Half-Sphere Electrode: 1 piece
6、 Bead Electrodes: 2 pieces
7、Cylinder Electrode: 1 piece
Vacuum/Spray:
1、 Single Pipe: 2 piece
2、 Round Glass Tube：1 piece
3、 Flat Glass Tube: 1 piece
4、 “T” Vacuum Pipe: 1 piece
5、 Gourd Glass Cups: 2 pieces
6、Spray Bottles: 2 piecesRotary Brush:
1、 Brush holder W/double-direction control: 1 piece
2、Brush: 5 pieces
Large Wool brush: 1 piece
Small Wool brush: 1 piece
Large Crystal scrubber: 1 piece
Small Crystal scrub: 1 piece
Sponge 1 piece
※Large wool brush –for face, forehead and chin
※Small wool brush –for eye areas, mouth area and nose area
※Crystal scrubbers –for rough skin
※Sponge –for sensitive skin and massage
……………………………………………………………….
………………………………………………………………
7
Multi-Function Beauty System USER MANUAL
Ultrasonic:
Ultrasonic probes: 2 piece.
A. Large flat (face and neck). B. Small pointy (eyes and nose).
Diamond microdamabration:
1.Big dermabrasion pen
2. Middle dermabrasion pen
3.Small dermabrasion pen
4.Diamond head (8 pieces)
METABOLIC DEPRESSOR:
Probe 5 pcs
Wood Lamp:
1、Shade cover: 1 piece
Facial Steamer Operations:
1、 Adjust the height of steamer. Be careful of bumping.
2、 Fill the glass jar with distill water only through water funnel u, do not exceed
the red warning line. Make sure the jar is attached firmly and perfectly to the steamer.
3、 Connect power plug. Adjust timer.
4、 Turn power r on, power switch should light up. Steam will come out in around 10-15
minutes after the power is switched on.
5、 Turn ozone s on only when steam comes out. Ozone switch should light up. Do not
turn ozone on when there is no steam.
6、 Position steam jet to aim at client’s chin and steam should travel over his/her
entire face.
7、 Use arm adjuster knob v to secure arm angle.
8、 When time is up, turn ozone off first, Then power.
9、 Unplug power socket and wait till the glass is cool before removing it from the
machine.
10、If it is needed to stop steaming during operation , turn power and ozone switches
off. The timer will still go on until it reaches OFF position.
11、For safety purpose ,the machine will automatically shut off when water level is
below the heating element.
Skin Types
Distance Duration(mins) Ozone
Oily, Combination
20cm
5-8
Y
Acne, Blemish
20cm
8-10
Y
Normal
25cm
10
Y
Dry, De-hydrated, Mature
30cm
3
Y
Sensitive, Sunburned
35cm
5-8
N
Capillaries, Inflammation 35cm
5
N
Pigment
30cm
10
N
Cleaning instructions for facial steamer:
1、 Glass jar and heat element should be cleaned at least once a week with distill water.
2、 Clean residues from heating element by using clean distill water and soft clothe.
Do not use any metal or abrasives.
3、Do not lose the rubber band on top of the glass jar. It is used to prevent water
spilling out.
High Frequency Operations:
1、 Sterilize accessories before and after each usage.
2、 Switch power b on.
……………………………………………………………….
………………………………………………………………
8
Multi-Function Beauty System USER MANUAL
3、 Adjust intensity f according to client’s skin type.
5 、 Turn intensity f to minimum(click sound)when finish using or exchanging
electrodes.(When exchange glass electrodes, please be careful that the glue on the
electrode is hot. Please twist slowly when pulling out the electrode in order to keep
the glue in place. If pull the electrode out, please be gentle in case the glass will
break.)
Methods of Performing High Frequency
Germicidal Effect (Direct Method Only) Direct Method of High Frequency
1、 Use the “mushroom” glass rod [ultraviolet].
2、 Limits sebaceous secretion.
3、 Germicidal, anti-bacterial effect.
4、 Drying and healing infection.
5、 With client relaxed (no jewelry on) the operator turns on machine.
6、 Operator places one hand on the client’s face and applies the electrode to the
face.
7、 The electrode is rotated directly on the face in small circles, Do not lift
electrode.
8、The operator places hand on client’s and removes electrode.
8、 Turn off machine.
Stimulation of Surface Tissue Sparking Method of High Frequency
1、 Use the “mushroom” glass rod.
2、 Penetrates to subcutaneous tissue (adipose face).
3、Generates heat that increases flow of blood tissue fluids.
4、Improves nutrition and elimination of skin.
5、Improves skin texture, oil and moisture balance to skin.
6、Operator sets up the same as in Direct Method procedure but electrode is lifted
slightly away from the skin to create a sparking effect between the electrode and the
client’s skin.
Relaxation effect on Body Indirect Method of High Frequency
1、Generates warmth within tissues, produces sedative effect.
2、Increases relaxation and relief from tension.
3、Does not affect muscles.
4、Client holds “straight” glass electrode in both hands (no jewelry on).
5、Operator places one hand on clients face.
6、To find out the right intensity, operator slowly turns on and up the intensity of
the machine at the same time lightly massaging the face and asking the client if they
feel a warm or prickly sensation to the skin.
7、When the client feels the warm or tingling sensation, the intensity is at its best
for that client.
8、Massage the face with both hands now with light strokes. Do not lift the fingers
from the face.
9、Massage for five minutes and then rest for two minutes; Then start again.
11、Turn off machine with one hand.
THEORY OF VACUUM Operations:
1、When plug in the pipes for THEORY OF VACUUM functions. Please insert the pipes in
to the correct plugs according to the pictures indicated.
……………………………………………………………….
………………………………………………………………
9
Multi-Function Beauty System USER MANUAL
2、Switch Vaccum theory Power on.
3、Vacuum: When vacuuming impurities, insert a tiny piece of cotton in order to block
any impurities getting into the machine. Also, do not use any toning lotion with powder
inside.
4、Use index or middle finger to cover the small hole on the vacuum glass tube in order
to provide suction function. Test power on the back of the hand before performing on
client. Higher power on oily and normal skins; lower power on dry, sensitive and mature
skin.
5、Spray: Use thumb to cover the small hole on the top of the spray bottle (VS6) in
order to let toning lotion spray out. Remember to spray from top to bottom in case lotion
gets into nose.
6、Turn intensity (h) to minimum (click sound) when finish using or exchanging glass
tubes.
Methods of Performing Vacuum Suction
Rhythmic Vacuum Suction: Use on large part of skin or sagging skin. Cover and release
the small hole on the tube frequently in order to perform a rhythm in suction.
Continuous Vacuum Suction: Use on oily or combination skins (especially on “T” zone
Cover the small hole until the tube reaches the edge of the face).
Strong Vacuum Suction: Use glass tube to perform this function on oily skin and parts
with blackheads and impurities. Cover the small hole and lift up in order to let the
impurities out of skin.
Lymphatic Drainage Vacuum Suction: Vacuum along the direction of the lymph. Cover the
small hole until the gourd glass cup reaches the edge of the face. Then repeat again.
Work upwards.
Galvanic-Deep Cleaning Operations:
1、Use a thin piece of cotton warp on the negative electrode and let client hold it.
2、Turn on power and Pos/Neg Switch to negative. Intensity indicator will light up.
3、Perform cleaning by using “zigzag” motions for around 3-5 minutes.
4 、 Each individual accepts different level of electric current in his/her body.
Indicator bar will light up differently as well according to different client. Once
the intensity indicator lights up to red and power continues to increase, system will
turn itself off automatically in order to protect both the machine and the client. If
operation needs to be continued, turn the intensity switch back to minimum till a click
sound is heard. Then start again.
5、Turn intensity to minimum (click sound) when finish using or exchanging electrodes.
Galvanic-Penetrating Operations:
1、Use a thin piece of cotton wrap on the negative electrode and let client hold it.
2、Apply water-base serum on skin.
3、Turn on power and Pos/Neg Switch to positive. Intensity indicator will light up.
4 、 Each individual accepts different level of electric current in his/her body.
Indicator bar will light up differently as well according to different client. Once
the intensity indicator lights up to red and power continues to increase, system will
turn itself off automatically in order to protect both the machine and the client. If
operation needs to be continued, turn the intensity switch back to minimum till a click
sound is heard. Then start again.
5、Perform penetrating by using “zigzag” or circular motions for around 5-6 minutes.
……………………………………………………………….
………………………………………………………………
10
Multi-Function Beauty System USER MANUAL
6、Turn intensity to minimum (click sound) when finish using or exchanging electrodes.
Skin Lifting Operations:
1、Insert two cotton swaps into the two lifting electrodes. Then apply water-base serum
on skin and the cotton swaps as well.
2、Turn on power and Pos/Neg Switch to negative. Intensity indicator will light up.
3、Perform lifting working upward slowly for 15-20 minutes. Motions should go according
to the jaw lines. When reach the lines between the eyebrows, perform along then
directions of the wrinkles.
4 、 Each individual accepts different level of electric current in his/her body.
Indicator bar will light up differently as well according to different client. Once
the intensity indicator lights up to red and power continues to increase, system will
turn itself off automatically in order to protect both the machine and the client. If
operation needs to be continued, turn the intensity switch back to minimum till a click
sound is heard. Then start again.
5、Turn intensity to minimum (click sound) when finish using or exchanging electrodes.
Rotary Brush Operations:
1、Switch Main Power on.
2、Connect the desire brush to the brush holder and connect to brush connector plug.
3、Turn on Brush Power on to begin.
4、Adjust the power of the brush by turning the intensity switch.
5、Apply cleansing milk on skin.
6、Push the direction control button upward to make the brush turn counter-clockwise
or push it downward to make the brush turn clockwise.
7、Use brush to cleanse/massage face for 3-5 minutes.
8、Rinse clean with lukewarm water.
9、Pat dry and continue with other steps of treatment.
10、Turn intensity to minimum (click sound) when finish using or exchanging brushes.
Ultrasonic Operations:
1. Sterilize probes, connect machine to probles.
2. Cleanse and steam skin. Remove blackheads. Apply water-base serum or gel according
to different skin types.
3. Press the start/pause of the Ultrasonic.
4. Choose which probe is to be used by pressing the Left/Right.
6. Choose frequency according to different skin types:
Sequential frequency ∞(11) is Ultrasonic X ray of constant intensity emitting
sequentially without interval. It has an even effect with obvious heat effect. It should
be chose for other situations which pulse wave should not be used.
Pulse frequency
(12) is ultrasonic X ray emitting at intervals and each pulse lasts
very short. The important feature of pulse wave is to decrease heat. Generally speaking,
pulse wave should be chosen for inflammation, redness, abscess and telangiectasia.
Frequency
Skin types
Sequential∞
Healthy/Normal skin
Oily, acne and blemish skins
Pulse frequency
Dry skin
Sensitive and capillaries skin
8. Press the intensity to adjust output power.
……………………………………………………………….
………………………………………………………………
11
Multi-Function Beauty System USER MANUAL
9. Use circular motions to operate probe on skin.
10. Turn power off when finish treatment. Leave skin alone for 5-8 minutes in order
to let skin absorb serum/gel completely.
Magnifying Lamp Operations:
1、Connect power plug.
2、Turn power on by press the power button on top lamp cover.
3、Adjust arm to desired height.
4、Secure arm with the knob.
Wood Lamp Operations:
1、After cleansing skin, cover client’s eyes with cotton.
2、Secure cover shade (W1)to wood lamp.
3、Completely cover client’s face with cover shade. The wood lamp should be parallel
to client’s face with distance of 15-20cm.
4、Identify different skin characteristics by appearances of different colors under
the ultraviolet ray.
Methods of Performing Wood Lamp
Light blue-normal and healthy skin
Purple-sensitive skin
Yellow-oily, acne skins
White spots-mature skin area
Brown-pigments
Reflecting light spot-impurities, make-up
Indigo-dry skin
Cautions:
1.Client has to take off all jewelry before treatment.
2.When perform facial steaming, client may feel breathless or hard to breathe if spray
steam directly towards nose.
3.If steam too long, skin may become dry. If steam too close, skin may feel too hot.
Do not turn ozone on for sensitive, capillaries and pigment skins.
4.The water filled in the glass jar must be distill water only. No other product or
liquid (e.g.essential oil) can be added.
5. When water is over the warning line, boiling water may splash out from both spray
head and glass jar.
6.Do not touch or remove the glass jar when machine is in use.
7.Make sure the steamer is off and cool before cleaning.
8.If refill of distill water is required, be sure to turn the machine off and jar is
cool before filling.
9.Turn intensity to minimum (click sound) when finish using or exchanging electrodes,
vacuum tubes ,spray bottles, or brushes.
10.When use high frequency for the first time or it has not been used for a long while,
it may seem not working. However, it is a normal reaction. Just turn the high frequency
on for a while, and it will be working again.
11.When using sparkling effect on high frequency, use wet cotton slices to cover eyes.
Only touch where it needs to be sterilized, maximum time of 10 seconds. Client will
feel tingling. Suitable to use on oily, acne, blemish skins.
……………………………………………………………….
………………………………………………………………
12
Multi-Function Beauty System USER MANUAL
12.If use on young skin, use gauze to cover face in order to reduce stimulations.
13.When exchange glass electrodes, please be careful that the glue on the electrode
is hot. Twist slowly when pulling out the electrode in order to keep the glue in place.
14.If pull the electrode out, please be gentle in case the glass will break and cut
skin.
15.Client with metal inside his/her body and pregnant women are not recommended to use
this machine.
16.When machine is on, do not touch the top part of the high frequency handle in order
to avoid electric shock.
17.Turn intensity to minimum (click sound) when finish using or exchanging electrodes
or glass tubes.
18.When plug in the pipes for vacuum/spray functions. Please insert pipes in to the
correct plugs according to the pictures indicated.
19.When vacuuming impurities, insert a tiny piece of cotton in order to block any
impurities getting into the machine.do not use any toning lotion with powder inside.
20.Do not leave the suction tubes or cup in one particular part of skin to avoid bruises.
21.Do not do vacuum suction in the delicate eye areas.
22.Do not increase power all of a sudden; it may tear muscles of client.
23.If need to stop treatment immediately, unplug vacuum pipe from vacuum plug.
24.Cotton swaps should be inserted into the lifting electrodes in order to prevent any
serious pain.
25.When performing galvanic or lifting, do not use too high of intensity (red is not
serious pain).
26.Avoid electrodes touch themselves since system will shut off automatically. If
operation needs to be continued, turn the intensity switch back to minimum till a click
sound is heard. Then start again.
27.Each individual accepts different level of electric current in his/her body.
According to this, once the intensity indicator lights up to red, it will turn itself
off automatically in order to protect both the machine and the client.
28.When using the wool brushes, touch skin with a 90°angle.
29.Do not go too close the hairline in case any hair gets rotated to the holder.
30.Clean and sterilize brushes before and after each usage. Brushes can not be
sterilized with high heat. Wool brushes have to be completely dry before sterilizing.
31.Store brushes in dry and clean place.
32.Soften rough skin before brushing.
33.Do not use on acne, cut or wounded skin.
34.Redness or slight pain may appear on young and sensitive skins after usage.
35.The wood lamp should be parallel to client's face with distance of 15-20cm. Do not
over-expose to the wood lamp since the ultraviolet ray may darken pigments or make skin
more sensitive. Maximum duration should be 2 minutes.
36.Cover client’s eyes with wet cotton to avoid making client’s eyes tired.
Main technical parameters:
Power source: 110V-120V/60Hz or 220V-240V/50Hz
Rated input power: 950W.
Category of electric shock prevention: Category 1
……………………………………………………………….
………………………………………………………………
13
Multi-Function Beauty System USER MANUAL
Size
G.W.
N.W.
……………………………………………………………….
………………………………………………………………
14