LeakBuster™ MATRIX™ 205 APP Flashing - MSDS #1035B

advertisement
MATERIAL SAFETY DATA SHEET
BUILDING MATERIALS CORPORATION OF AMERICA
4 = EXTREME
FLAMMABLE
Leak Buster™ Matrix 105 Brush Grade AP Adhesive Label
Leak Buster™ Matrix 205 APP Flashing Label
HEALTH
2
3 = HIGH
2 = MODERATE
REACTIVE
1
0
1 = SLIGHT
SPECIAL
HAZARDS
--
0 = INSIGNIFICANT
Manufacturer Building Materials
Address 1361 Alps Road
Identity (Trade Name As Used On Label)
Corporation of America
MSDS Number* 1035B
Wayne , NJ 07470
Phone Number (For Information)
800-766-3411
Emergency Phone Number 800-424-9300
CAS Number*
N/A
Date Prepared
12/98
Revised 2818/04
Prepared By* A. Khan/PJH
NOTE: Blank spaces are not permitted. If any item is not applicable, or
no information is available, the space must be marked to indicate that.
SECTION 1 - MATERIAL IDENTIFICATION AND INFORMATION
COMPONENTS - Chemical Name & Common
Names (Hazardous Components 1% or Greater;
%*
OSHA
ACGIH
OTHER LIMITS
PEL
TLV
RECOMMENDED
100 mg/m3
0.5 mg/m3
N/A
N/A
Carcinogens 0.1% or greater)
Mineral Spirits – CAS 64742-88-7
Petroleum Asphalt - CAS 8052-42-4
30
70
Non-Hazardous Ingredients
100 ppm
None
Established
(solvent
soluble)
0
Total
100
SECTION 2 – PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point
300 to 320o Solvent only
Specific Gravity (H2O = 1)
Vapor Pressure (mm Hg and Temperature)
2 mm (Solvent)
Melting Point
Vapor Density (Air = 1)
>1
Solubility in Water
Nil
Evaporation Rate (Butyl Acetate =
1)
Water Reactive
Appearance and Odor
1
n/a
<1
n/a
Black Paste, Solvent Odor
SECTION 3 - FIRE AND EXPLOSION HAZARD DATA
Flash Point and
110o
Method Used
TCC
Extinguisher Media
Auto-Ignition
Temperature
Flammability Limits in
LEL
Air % by Volume
0.9
UEL
6.7
Foam, Dry Chemical, CO2 – DO NOT USE WATER
Special Fire Fighting Procedures
Treat as fuel oil fire. Self-contained breathing apparatus recommended.
Unusual Fire and Explosion Hazards
* Optional
N/A
COMBUSTIBLE. Keep away from open flame and sources and heat.
OSHA 174
Page 1/2
MSDSGAF
SECTION 4 - REACTIVITY HAZARD DATA
STABILITY
Stable
Unstable
__x__
Conditions Open flames, all sources of ignition. Do not heat or thin this material.
____
Incompatibility (Materials to Avoid)
To Avoid
May react with strong oxidizing agents, reducing agents, strong acids and alkalies.
Hazardous Decomposition Products Carbon Monoxide and Carbon Dioxide
HAZARDOUS POLYMERIZATION
____ May Occur
Conditions
_x___ Will Not Occur
Do not heat or thin this material.
To Avoid
SECTION 5 - HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY:
_x__ Inhalation __x_ Skin Absorption
HEALTH
HAZARDS
CARCINOGEN LISTED IN:
_x__ Ingestion
__x_ Eye
n/a NTP _x__ IARC Monograph _n/a__ OSHA _n/a_ Not Listed
Acute and Chronic and Signs and Symptoms of Exposure :
Prolonged or repeated skin contact with this product may result in irritation and dermatitis.
Asphalt: The International Agency for Research on Cancer (IARC) has determined that there is sufficient evidence for
the carcinogennicity of extract of steam-refined bitumens, air-refined bitumens and pooled mixtures of steam-and airrefined bitumens in experimental animals. Possible skin cancer hazard based on tests with laboratory animals. This
product may contain polynuclear aromatic hydrocarbons, some of which may be types that have been shown to cause
skin cancer in laboratory animals. This product has not been tested as a whole for all potential health effects. It may
have other health hazards related to its components. Skin contact, breathing of mists, fumes or vapors should be
reduced to a minimum to avoid any ill effects. Chronic health effects would not be expected as long as good hygiene
and proper safety precautions are practiced.
Signs and Symptoms of Exposure:
Eye Contact: May cause irritation, blurred vision.
Ingestion: Can Cause gastrointestinal irritation.
Skin Contact: Prolonged contact may cause irritation and/or dermatitis.
Inhalation: Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. This material
is for exterior use only.
Medical Conditions Generally Aggravated by Exposure: Persons with a history or chronic skin or respiratory disorders may be at
increased risk for a worsening of their condition from exposure to this product.
EMERGENCY FIRST AID PROCEDURES Eye Contact:
Flush with large amounts of water. Consult a physician.
Skin Contact: Clean affected area with a waterless hand cleaner, then wash area thoroughly with soap and water. If redness, etc.
persists, consult a physician.
Inhalation: Remove person from area. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration.
Seek immediate medical aid.
Ingestion: Do not induce vomiting. Consult a physician immediately.
SECTION 6 – CONTROL AND PROTECTIVE MEASURES
Respiratory Protection (Specify Type) – Normally not needed. If TLV is exceeded, use approved NIOSH/MSHA respirator.
Protective Gloves
Oil resistant recommended.
Eye Protection Chemical splash
goggles.
VENTILATION
__x__ Local Exhaust
TO BE USED
_n/a_ Special
_n/a___ Mechanical (General)
_n/a___ Other (Specify)
Other Protective Clothing and Equipment: Impervious work clothing is recommended.
Hygienic Work Practices: Wash hands after use.
SECTION 7 – PRECAUTIONS FOR SAFE HANDLING AND USE/LEAK PROCEDURES
Steps to be Taken if Material is Spilled or Released: Dike spill area; add absorbent to liquid. Keep out of sewers and waterways.
Remove any sources of ignition. Ventilate area if necessary.
Waste Disposal Methods: Dispose in approved landfill in accordance with Federal, State and Local regulations. Follow proper
container management in disposing of containers (CERCLA amendment).
Precautions to be Taken in Handling and Storage: Keep away from sources of ignition; open flame. This material is for exterior use only.
Other Precautions and/or Special Hazards Practice good personal hygiene. Launder contaminated clothing before reuse. Use control
protection such as chemical splash proof goggles, oil resistant gloves, barrier cream. Clean tools and equipment with kerosene. DO
NOT USE GASOLINE.
MSDS NO.
1035B
PAGE 2/2
Download