MATERIAL SAFETY DATA SHEET
Shield Industries, Inc.
Day Telephone: (770) 517-6869
131 Smokehill Lane
Woodstock, GA 30188
Emergency Telephone: 1-800-535-5053
32oz MoldBlaster (Ready To Use)
Section I Product Identification
Product ID: FF MBT32C6
Product Class: Quaternary Ammonium Compound
Last Revision Date: 04/23/07
EPA Reg. Number: 10324-85-72251
Preparer: R. Lasnik, Vice President
Section II Hazardous Ingredients
Alkyl dimethyl benzyl ammonium chloride (C12-C16)
Octyl decyl dimethyl ammonium chloride
Dioctyl dimethyl ammonium chloride
Didecyl dimethyl ammonium chloride
Isopropyl Alcohol
HMIS Rating: Health-1
Flammability-0
CAS#
68424-85-1
32426-11-2
5538-94-3
7173-51-5
67-63-0
Reactivity-0
Wt.%
< 0.1
< 0.1
< 0.1
< 0.1
2
Protection-X
Section III Hazards Identification
Emergency Overview: Clear, colorless to straw colored liquid. Mildly corrosive to the eyes, skin,
gastrointestinal tract, and respiratory system.
Potential Health Effects:
Skin:
May be mildly irritating. Extensive and prolonged exposure may be harmful.
Eyes:
May cause irritation.
Inhalation:
Mists and vapors can be mildly irritating to the throat and respiratory tract.
Ingestion:
Harmful if swallowed.
Section IV First Aid Measures
Eyes:
Immediately flush eyes with water for at least 15 minutes, while holding eyelids open.
Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye.
Seek medical attention at once.
Skin or Clothing: Take off contaminated clothing. Rinse skin immediately with plenty of water for 15-20
minutes. Call a poison control center or doctor for treatment advice.
Inhalation:
If symptoms are experienced, move victim to fresh air. If person is not breathing, call 911
or an ambulance, then give artificial respiration, preferably mouth-to-mouth if possible.
Call a poison control center or doctor for further treatment advice.
Ingestion:
Call a poison control center or doctor immediately for treatment advice. Have person sip a
glass of water if able to swallow. Do not induce vomiting unless told to do so by a poison
control center or doctor. Do not give anything by mouth to an unconscious person.
Section V Fire Fighting Measures
Flash Point: None @ 102 °C (Open Cup)
Upper & Lower Flame Limits: Not determined.
Extinguishing Media: Use any agent appropriate for surrounding fire.
Fire Fighting Equipment & Instructions: Firefighters should wear full protective clothing including
self-contained breathing apparatus. Cool fire exposed containers with spray.
Hazardous Combustion Products: Irritating and toxic gases or fumes may be released during a fire.
Page 1 of 4
MSDS For Forcefield® MoldBlaster (Ready To Use)
Section VI Accidental Release Measures
Spill and Leak Procedures:
Emergency Action: Isolate spill or leak area immediately. Keep unauthorized personnel away.
Stay upwind.
Spill Cleanup:
Ventilate closed spaces before entering. Floor will be slippery. Do not touch
or walk through spilled material. Stop leak if you can do it without risk.
Prevent entry into waterways, sewers, basements or confined areas. Absorb or
cover with dry earth, sand, or other non-combustible material and transfer to
containers.
Large Spills:
Dike far ahead of liquid spill for later disposal.
Waste Disposal:
Dispose of only by methods approved by and used in accordance with local,
state, and federal regulations.
Section VII Handling & Storage
Handling Procedures: Avoid contact with skin and eyes. Use good personal hygiene practices. Wash
hands before eating, drinking, smoking, or using toilet facilities. Wash thoroughly after
work using soap and water.
Storage Procedures: Keep the container tightly closed and in a cool, well-ventilated place. Keep from
freezing.
Section VIII Exposure Controls/ Personal Protection
Engineering Controls: Provide adequate local exhaust ventilation to if necessary to maintain
worker exposure below exposure limits.
Personal Protective Equipment:
Eyes/Face:
Wear safety glasses or chemical goggles.
Skin:
Use impervious gloves (rubber or neoprene). Wear protective clothing.
Respiratory: Not normally required.
General:
Eye wash fountain and emergency showers are recommended.
The following ingredients have established exposure guidelines: (All TWAs are for 8-hour period.)
(Values are presented for ingredients present in sufficient quantity to warrant disclosure. Some
ingredients present at below OSHA and/or WHMIS disclosure values are not presented. eg., glycerin)
Ingredient
Isopropyl
Alcohol
CAS# Exposure Guideline
67-63-0 ACGIH TLV (2004) OSHA PEL & NIOSH REL
OSHA PEL
NIOSH (Pocket Guide)
Canadian Provinces (except BC)
British Columbia
Mexico
Monoethanolamine 67-63-0 ACGIH TLV (2004) OSHA PEL & NIOSH REL
OSHA PEL
NIOSH (Pocket Guide)
Canadian Provinces
Mexico
Page 2 of 4
MSDS For Forcefield® MoldBlaster (Ready To Use)
Guideline Value
200 ppm (TWA)
400 ppm (TWA)
400 ppm (TWA)
400 ppm (TWA)
200 ppm (TWA)
400 ppm (TWA)
3 ppm (TWA)
3 ppm (TWA)
3 ppm (TWA)
3 ppm (TWA)
3 ppm (TWA)
Section IX Physical & Chemical Properties
Flash Point:
None @ 102°C (Open Cup) Specific Gravity:
0.9992
Percent Volatiles:
Not determined
Vapor Pressure:
Not determined
VOC Content:
Not determined
Vapor Density:
Not determined
Viscosity:
0.955 cs
Evaporation Rate:
Not determined
Pour Point:
Not determined
pH:
7.99
Appearance and Odor: Clear, colorless to straw colored liquid with mild citrus odor.
Section X Stability & Reactivity
Chemical Stability: Material is stable.
Conditions to Avoid: Keep away from heat and strong oxidizing agents.
Incompatibilities:
Strong oxidizing agents, reducing agents.
Hazardous Decomposition: Carbon monoxide, carbon dioxide and toxic hydrogen chloride vapors.
Hazardous Polymerization: Will not occur.
Section XI Toxicological Information
Carcinogenicity:
No Carcinogenicity data available for this product. There are no chemical
ingredients that are listed as potential of know carcinogens.
Acute Oral LD50:
> 5000 mg/kg (rat)
Acute Dermal:
> 2000 mg/kg (rat)
Primary Skin:
Not an irritant.
Primary Eye:
Mildly irritating.
Section XII Ecological Information
Ecotoxicity:
No data available for this product, but is considered toxic to fish.
Section XIII Transport Information
DOT Hazard Class: Not regulated.
DOT Proper Shipping Name: Not applicable
Section XIII Regulatory Information
TSCA Status: While all ingredients are listed on the TSCA Chemical Inventory, this product is regulated
as a pesticide under the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA) and not
subject to the TSCA Inventory rules for FIFRA uses.
Other Chemical Inventories: All components of this product are listed on the following inventories:
Canada (DSL), European Union, China, Korean and Philippines. One or more ingredients are not
listed on the following inventories: Australia and Japan.
CERCL/SARA:
SARA Title III, Sections 311/312 – This product contains no ingredients subject to the reporting
requirement of this provision.
SARA Title 313 – This product contains no ingredients subject to the reporting requirement of this
provision.
Reportable Quantities/Threshold Planning Quantities: This product contains no ingredients
subject to the reporting requirement of this provision.
Page 3 of 4
MSDS For Forcefield® MoldBlaster (Ready To Use)
State & Provincial Right to Know & Selected Regulatory Lists: The following ingredients appear
on the various state right to know lists and/or California’s Proposition 65 List.
Chemical Name
State List
Ethanol
AZ, CA, CAP65R, CT, FL, ID, MA, MN, NJ, PA, RI
Benzyl Chloride (Trace Impurity < 10 ppm) AZ, CA, CAR65C, FL, IL, MA, MN, NJ, PA
AZ – Arizona Ambient Air Quality Guidelines
CT – Connecticut Hazardous Air Pollutants
CA – California Director’s List of Hazardous Substances
CA65C – California Prop 65 Carcinogen
CA65R – California Prop 65 Reproductive Toxin
FL – Florida Substances List
ID – Idaho Non-Carcinogen Toxic Air Pollutants
IL – Illinois Toxic Air Contaminant – Carcinogenic
MA – Massachusetts Right to Know List
MN – Minnesota Hazardous Substances List
NJ – New Jersey Right to Know List
PA – Pennsylvania Right to Know List
RI – Rhode Island Hazardous Substances List
Disclaimer: As the handling and use of products under user’s conditions are beyond our control, no
warranty, expressed or implied, including, but not limited to merchantability or fitness for a particular use,
is made concerning this product. The user assumes all risk of use or handling whether or not in accordance
with any directions or suggestions of the supplier. Seller shall not be liable to purchaser or any other
person for loss or damages directly or indirectly arising from the use of our products, from breach of any
warranty or from any other cause, the exclusive remedy against the seller being to require replacement or
repair of defective goods.
Page 4 of 4
MSDS For Forcefield® MoldBlaster (Ready To Use)