SHUCARE AUSTRALIA PTY LTD
SHOE CARE PRODUCTS
Material Safety Data Sheet
Hazardous Substance, Dangerous Goods
1. MATERIAL AND SUPPLY COMPANY IDENTIFICATION
Product name: 708 PU ADHESIVE
Distributor:
Shucare Australia Pty Ltd
Street Address:
52 Kolara Rd,
Heidelberg West,
Victoria 3081,
Australia.
Telephone:
+603-9458 4949
Facsimile:
+603-9459 5525
2. HAZARDS IDENTIFICATION
May cause sensitisation by skin contact –irritating to eyes, respiratory system and skin.
Harmful by inhalation, in contact with skin and if swallowed.
3. COMPOSITION INFORMATION
CHEMICAL
Polyurethane Resin
Methylbenzene (Tolune)
Methyl Ethyl Ketone
ENTITY CAS NO.
30662-91-0
108-88-3
78-93-3
PROPOTION
<18%
<30%
>50%
100%
4.FIRST AID MEASURES
General Information
Seek medical assistant if discomfort continues
Inhalation:
Remove victim to fresh air. Remove contaminated clothing and loosen remaining clothing. Allow
patient to assume most comfortable position, keep warm. Keep at rest until fully recovered. Seek
medical advice if effects persist.
Skin contact:
Wash contaminated skin with plenty of water and soap. Remove contaminated clothing before reused.
Seek medical attention in event of irritation.
Eye contact:
Rinsed immediately with plenty of water. In all cases of eyes contamination it is a sensible precaution to
seek medical advice.
Ingestion:
Product name: 708 PU ADHESIVE
Issued: 30th Nov 2010
1
Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink. Never
give anything by the mouth to an unconscious patient. If vomiting occurs give further water. Get to a
doctor or hospital quickly.
Symptom
Until now no symptoms known so far.
Notes to physician:
Treat symptomatically.
5. FIRE- FIGHTING MEASURES
Suitable extinguishing media:
Use dry chemical powder, foam, carbon dioxide, water fog, sand and earth.
Unsuitable extinguish media:
Do not use Water in A Jet
6. ACCIDENTAL RELEASE MEASURES
SMALL SPILLS
Wear protective equipment to prevent skin and eye contamination. Wipe up with absorbent (clean rag or paper
towels). Allow absorbent to dry before disposing with normal household garbage.
LARGE SPILLS
Wear protective equipment to prevent skin and eye contamination and the inhalation of dust. Work up wind or
increase ventilation. Cover with damp absorbent (inert material, sand or soil). Sweep or vacuum up, but avoid
generating dust. Collect and seal in properly labelled containers or drums for disposal.
7.HANDLING AND STORAGE
Handling: Ensure good ventilation during processing.
Storage: Keep container tightly closed and dry.
Protection against fire/explosion: General rules of fire prevention should be observed.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Industrial hygiene: Remove immediately all contaminated clothing. Do not inhale vapours.
Hand protection: Suitable protective gloves.
Eye protection: Protective goggles
9. PHYSICAL AND CHEMICAL PROPERTIES
Form / Colour / Odour:
Viscous liquid.
Colour:
Starcy
Viscosity:
3000-3500 cps
Solid Content:
13-17%
Odour:
Aromatic odour
Melting Temperature:
N App
Boiling temperature:
86 oC
Solubility:
insoluble water.
Specific Gravity (20 °C):
N Av
Density (air=1):
0.87±0.001 g/cm3
Vapour Pressure (20 °C):
N Av
Flash Point (°C):
-9 oC
Product name: 708 PU ADHESIVE
Issued: 30th Nov 2010
2
Ignition Temperature (°C):
N Av
(Typical values only - consult specification sheet)
N Av = Not available
N App = Not applicable
10. STABILITY AND REACTIVITY
Chemical stability: No information available.
Conditions to avoid: Avoid potential sources of ignition.
Hazardous decomposition products: No information available.
Hazardous reactions: No dangerous reaction known.
11. TOXICOLOGICAL INFORMATION
Skin: May cause sensitisation
Eyes: Possibly irritating
12. ECOLOGICAL INFORMATION
Large quantities of product should not be allowed to enter drains or water courses or be deposited where it can
affect ground or surface water.
13. DISPOSAL CONSIDERATIONS
Do not allowed large quantities to enter the drains or water courses or dispose of where ground or surface water
may be affected. Residue s in emptied containers should be covered and should be disposed of in accordance
with regulations made under the control of Pollution & Environmental Protection Acts.
14. TRANSPORT INFORMATION
Dangerous good under the transport regulations.
UN No:
1133
Dangerous Goods Class:
3
Packing Group:
II
15. REGULATORY INFORMATION
The product is classified and labelled for supply in accordance with the Classification of Hazard Chemical. Regulation as
follow:
Classification
Highly Flammable
Harmful
Irritant to skin
R-phrases 43
36/38
S-phrases Z
May causes sensitization by skin contact
Irritant to skin
Keep out of reach of children.
28
After contact with skin, wash immediately with plenty of water
26
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
27
Take off immediately all contaminated clothing
37
Wear suitable gloves
46
If swallowed. Seek medical advice immediately and show this container label.
16. OTHER INFORMATION
The information contained in Safety Data Sheet is based on our present state of knowledge and experience and it
provides guidance on health, safety and environmental aspects. We do, however pass them without any warranty or
property assurances.
Product name: 708 PU ADHESIVE
Issued: 30th Nov 2010
3