IEEE C80216m-10/1029
Le
Project
IEEE 802.16 Broadband Wireless Access Working Group <http://ieee802.org/16>
Title
Carrier switching operation for E-MBS receiving
Date
Submitted
2010-08-13
Source(s)
Nan Li，Kaiying Lv，Bo Sun
E-mail: lv.kaiying@zte.com.cn
Feng Xie，Yuqin Chen
ZTE Corporation
Re:
Sponsor ballot comment on P802.16m/D7
Abstract
This contribution proposes texts on carrier switching operation for E-MBS receiving in
connected state.
Purpose
To be discussed and adopted.
Notice
Release
Patent
Policy
This document does not represent the agreed views of the IEEE 802.16 Working Group or any of its subgroups. It
represents only the views of the participants listed in the “Source(s)” field above. It is offered as a basis for
discussion. It is not binding on the contributor(s), who reserve(s) the right to add, amend or withdraw material
contained herein.
The contributor grants a free, irrevocable license to the IEEE to incorporate material contained in this contribution,
and any modifications thereof, in the creation of an IEEE Standards publication; to copyright in the IEEE’s name
any IEEE Standards publication even though it may include portions of this contribution; and at the IEEE’s sole
discretion to permit others to reproduce in whole or in part the resulting IEEE Standards publication. The
contributor also acknowledges and accepts that this contribution may be made public by IEEE 802.16.
The contributor is familiar with the IEEE-SA Patent Policy and Procedures:
<http://standards.ieee.org/guides/bylaws/sect6-7.html#6> and
<http://standards.ieee.org/guides/opman/sect6.html#6.3>.
Further information is located at <http://standards.ieee.org/board/pat/pat-material.html> and
<http://standards.ieee.org/board/pat>.
IEEE C80216m-10/1029
Carrier switching operation for E-MBS receiving
Nan Li, Kaiying Lv, Bo Sun, Feng Xie，Yuqin Chen
ZTE Corporation
1. Problem Statement
According to 802.16m/D6, if a carrier-switching enabled AMS subscribes E-MBS service flows transmitted
on carriers other than the AMS’s primary carrier, it shall perform carrier switching to receive those E-MBS
service flows. However, in EMBS deployment, based on EMBS application design, the AMS doesn’t need
to receive and decode all subscribed service flows simultaneously. While in this case, the ABS, in current
D6, could not detect when exactly the AMS receives its favorite EMBS service flows and when is possible
to schedule unicast services for the AMS. The ABS has to assume that the AMS receive all subscribed
service flows and then schedule unicast services for this AMS with lowest scheduling efficiency. Especially
for free Broadcast service which does not need any join procedure in application layer, there will be no DSA
procedure in the air interface between the ABS and the AMS. Neither can the ABS schedule unicast services
efficiently under this scenario.
2. Proposed Schemes
We propose that for a carrier switching enabled AMS, which performs primary to secondary carrier
switching for E-MBS, before the AMS start receiving EMBS data or the AMS decides to change its current
receiving service flows, it shall send the information about which E-MBS service(s) it intends to receive to
the ABS before switching.
To provide this information, an E-MBS Connection Bitmap combined with an E-MBS Zone Bitmap could
be used. Before switching, the AMS sends an E-MBS Connection Bitmap in an AAI_EMBS-REV-IND
message to the ABS. Each bit of the E-MBS Connection Bitmap maps to an E-MBS connection. The LSB of
the bitmap presents the E-MBS connection with the lowest E-MBS ID +FID value. The E-MBS service(s)
the AMS has subscribed are mapped in ascending order of their E-MBS ID+FID value from LSB to MSB of
the bitmap. The corresponding bit will be set to 1 if the AMS is going to receive relative E-MBS service. A
value 0 means the AMS does not intend to receive the E-MBS service. An E-MBS Zone Bitmap could also
be included to indicate which zone a specified E-MBS connection belongs to. An example of E-MBS
Connection Bitmap is shown as follows.
Table 1 AAI_EMBS-REV-IND parameters
M/O
Attributes / Array of attributes
Size
(bits)
Value/Notes
M
Action code
1
0b0: E-MBS Connection
Bitmap has been
changed
Conditions
IEEE C80216m-10/1029
0b1:AMS stops
receiving E-MBS service
O
E-MBS Zone Bitmap
7
Shall be
included if the
value of Action
code is 0
O
E-MBS Connection Bitmap
16
Shall be
included if the
value of Action
code is 0
After receiving an AAI_EMBS-REV-IND message, the ABS transmits an AAI_EMBS-REV-RSP message
in response. An Action Time may be included in the AAI_EMBS-REV-RSP message to indicate the time
the ABS allows the AMS to start carrier switching. When the AMS changes the concurrent receiving EMBS service(s), it sends the message with an updated E-MBS ID +FID list/ E-MBS Connection Bitmap to
the ABS.
Meanwhile, the ABS should pre-define a minimal time interval for the AMS to perform carrier switching.
After decoding AAI_E-MBS-CFG Message, E-MBS MAP Message or E-MBS service data burst, if the time
interval between the current E-MBS relative control message / E-MBS data burst and the next one is shorter
than or equal to the minimal time interval, the AMS should not switch back to the primary carrier. And the
ABS should not consider the AMS is available on the primary carrier.
3. Text Proposal
======================== Start of Proposed Text =====================
[Change text in P870, Line 46, 16.9.2.4 E-MBS Operation on the multi-carrier deployment as follows:]
The AMS with only one transceiver may perform primary to secondary carrier switching where E-MBS
configuration message and the E-MBS data are transmitted on an alternative carrier to the AMS and other
communication with ABS is performed in the primary carrier. The AMS sends an AAI_EMBS-REV-IND
message to the ABS to inform the ABS which E-MBS service(s) it intends to receive. After receiving an
AAI_EMBS-REV-IND message, the ABS transmits an AAI_EMBS-REV-RSP message in response. An
Action Time may be included in the AAI_EMBS-REV-RSP message to indicate the time the ABS allows
the AMS to start performing carrier switching. The ABS schedules unicast services for the AMS on its
primary carrier based on AAI_EMBS-REV-IND message. When the AMS changes the concurrent receiving
E-MBS service(s), it sends the message with an updated E-MBS Connection Bitmap and/or E-MBS Zone
Bitmap.
The ABS pre-defines a minimal time interval (e.g., 3 subframes) for indicating whether the AMS needs to
perform carrier switching back to primary carrier. After decoding AAI_E-MBS-CFG Message, E-MBS
IEEE C80216m-10/1029
MAP Message or E-MBS service data burst, if AMS detects the time interval between the current E-MBS
relative control message / E-MBS data burst and the next one is shorter than or equal to the minimal time
interval, the AMS should not switch back to the primary carrier. The ABS should not assume the AMS is
available on the primary carrier.
…
[Insert the following text to 16.2.3:]
16.2.3.x AAI_EMBS-REV-IND
The AMS sends an AAI_EMBS-REV-IND message to inform the ABS which E-MBS service(s) the AMS
intends to receive. Table XXX shows the parameters for AAI_EMBS-REV-IND message:
Table XXX AAI_EMBS-REV-IND parameters
M/O
Attributes
attributes
/
Array
of Size
(bits)
Value/Notes
Conditions
M
Action code
1
0b0: E-MBS Connection Bitmap
indicating currently receiving services
0b1: AMS stops receiving E-MBS
service
O
E-MBS Zone Bitmap
7
Each bit of the bitmap presents an E- Shall be included
MBS zone supported by the ABS. The if the value of
E-MBS zones are mapped from LSB Action code is 0
to MSB in ascending order of the
value of Zone ID.
For each bit:
Value 0: The AMS does not intend to
receive E-MBS service in the specific
zone.
Value 1: The AMS is going to receive
E-MBS service in the specific zone.
O
E-MBS Connection Bitmap
16
Each bit of the bitmap presents an EMBS connection in one E-MBS Zone.
The E-MBS service(s) are mapped in
ascending order of their E-MBS
ID+FID value from LSB to MSB of
the bitmap.
Shall be included
if the value of
Action code is 0.
Shall be included
for each E-MBS
zone as indicated
in E-MBS Zone
For each bit:
Bitmap
with
Value 0: The AMS does not intend to value of “1”.
IEEE C80216m-10/1029
receive the E-MBS service.
Value 1: The AMS is going to receive
relative E-MBS service.
16.2.3.y AAI_EMBS-REV-RSP
The AAI_EMBS-REV-RSP message is transmitted by the ABS in response to an AAI_EMBS-REV-IND
message sent by the AMS.
Table XXX AAI_EMBS-REV-RSP parameters
M/O
Attributes / Array of attributes
Size
Value/Notes
Conditions
(bits)
M
Action code
1
0b0：confirm AMS’s
switching
0b1：refuse AMS to
leave the primary carrier
or confirm AMS of
stopping receiving EMBS service
O
Action Time
4
Indicates the switching
May be
time by frame number
the AMS could start
carrier switching.
included when
action
code=0b0.
============================== End of Proposed Text ============================