ECE 477 Final Report  Fall 2013
Team #  Team ID
Due Monday, December 9, at 5:00 PM
Submit “.docx” of completed report on-line
Place a photograph of the project team (annotated with names) along with the
completed project here.
Please delete this text box before printing your report!
Team Members:
#1: ____________________________
Signature: ____________________ Date: _________
#2: ____________________________
Signature: ____________________ Date: _________
#3: ____________________________
Signature: ____________________ Date: _________
#4: ____________________________
Signature: ____________________ Date: _________
CRITERION
Technical content
Design documentation
Technical writing style
Contributions
Editing
Comments:
SCORE
0
0
0
0
0
1
1
1
1
1
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
6
6
6
6
6
MPY
7
7
7
7
7
8
8
8
8
8
9
9
9
9
9
10
10
10
10
10
3
3
2
1
1
TOTAL
PTS
ECE 477 Final Report
Fall 2013
Table of Contents
Abstract ........................................................................................................................................... 1
1.0 Project Overview and Block Diagram ................................................................................. 1
1.1 Sample Heading 2 ...........................................................Error! Bookmark not defined.
1.1.1 Sample Heading 3 ....................................................Error! Bookmark not defined.
2.0 Team Success Criteria and Fulfillment ................................................................................ 1
3.0 Constraint Analysis and Component Selection.................................................................... 1
4.0 Patent Liability Analysis ...................................................................................................... 1
5.0 Reliability and Safety Analysis ............................................................................................ 1
6.0 Ethical and Environmental Impact Analysis........................................................................ 1
7.0 Packaging Design Considerations........................................................................................ 1
8.0 Schematic Design Considerations........................................................................................ 2
9.0 PCB Layout Design Considerations .................................................................................... 2
10.0 Software Design Considerations .......................................................................................... 2
11.0 Version 2 Changes ............................................................................................................... 2
12.0 Summary and Conclusions .................................................................................................. 2
13.0 References ............................................................................................................................ 2
Appendix A: Individual Contributions ..................................................................................... A-1
A.1 Contributions of ?:........................................................................................................ A-1
A.2 Contributions of ?:........................................................................................................ A-1
A.3 Contributions of ?:........................................................................................................ A-1
A.4 Contributions of ?:........................................................................................................ A-1
Appendix B: Packaging ............................................................................................................ B-1
Appendix C: Schematic ............................................................................................................ C-1
Appendix D: PCB Layout Top and Bottom Copper ................................................................ D-1
Appendix E: Parts List Spreadsheet ..........................................................................................E-1
Appendix F: FMECA Worksheet .............................................................................................. F-1
-ii-
ECE 477 Final Report
Fall 2013
NOTE: The text body should be 12 point (Times New Roman), vertical spacing 16 point
Abstract
Place a single-paragraph project abstract here.
1.0 Project Overview and Block Diagram
Place the project overview here – it should include a block diagram along with a photograph of
the completed project.
2.0 Team Success Criteria and Fulfillment
2.1 Test Heading 2
2.1.1 Test Heading 3
Place your list of team success criteria (must be the list written/approved by the course staff)
here along with an assessment of their fulfillment.
3.0 Constraint Analysis and Component Selection
An edited version of Homework #3 should be inserted here – the parts list spreadsheet should be
included as Appendix E.
4.0 Patent Liability Analysis
An edited version of Homework #10 should be inserted here.
5.0 Reliability and Safety Analysis
An edited version of Homework #11 should be inserted here – the FEMCA worksheet should be
included as Appendix F.
6.0 Ethical and Environmental Impact Analysis
An edited version of Homework #12 should be inserted here.
7.0 Packaging Design Considerations
-1-
ECE 477 Final Report
Fall 2013
An edited version of Homework #4 should be inserted here – the packaging illustrations should
be included as Appendix B.
8.0 Schematic Design Considerations
An edited version of Homework #5 should be inserted here – the schematic should be included as
Appendix C.
9.0 PCB Layout Design Considerations
An edited version of Homework #6 should be inserted here – the PCB top and bottom copper
illustrations (with silkscreen) should be included as Appendix D.
10.0 Software Design Considerations
An edited version of Homework #9 should be inserted here – the software listing should be
submitted separately.
11.0 Version 2 Changes
Place the list of “second iteration” changes you would make here (“what you would do now that
you know what you know”).
12.0 Summary and Conclusions
Place a summary of what you accomplished and what you learned here.
13.0 References
Place your complete list of references here.
NOTE: All references should be numbered (1, 2, 3…) and cited in text using
[1], [2], [3]… Use standard IEEE format. All URLs should be hot links.
-2-
ECE 477 Final Report
Appendix A:
Fall 2013
Individual Contributions
Each team member should provide a detailed (one page minimum, two page maximum)
description of his/her individual contributions to the project.
A.1 Contributions of ?:
one page minimum / two page maximum
A.2 Contributions of ?:
one page minimum / two page maximum
A.3 Contributions of ?:
one page minimum / two page maximum
A.4 Contributions of ?:
one page minimum / two page maximum
A-1
ECE 477 Final Report
Appendix B:
Fall 2013
Packaging
Include your packaging illustrations here – note that all figures should be numbered and
captioned.
Sample caption:
Figure B-1. Top view of product packaging.
“B” because this figure is in Appendix B
B-1
ECE 477 Final Report
Appendix C:
Fall 2013
Schematic
A copy of the final schematic should be included here – note that all figures should be numbered
and captioned.
C-1
ECE 477 Final Report
Appendix D:
Fall 2013
PCB Layout Top and Bottom Copper
A copy of the top and bottom copper PCB layout (with silkscreen) should be included here – note
that all figures should be numbered and captioned.
D-1
ECE 477 Final Report
Appendix E:
Fall 2013
Parts List Spreadsheet
A copy of the parts list spreadsheet (bill of materials) should be included here.
E-1
ECE 477 Final Report
Appendix F:
Failure
No.
Fall 2013
FMECA Worksheet
Failure Mode
Possible Causes
Failure Effects
F-1
Method of
Detection
Criticality
Remarks