From iMPACT:
-
“Cable Autoconnect” results
GUI --- Auto connect to cable...
// *** BATCH CMD : setCable -port auto
INFO:iMPACT - Digilent Plugin: found 1 device(s).
INFO:iMPACT - Digilent Plugin: opening device: "obp", SN:000000000000
INFO:iMPACT - Digilent Plugin: User Name: obp
INFO:iMPACT - Digilent Plugin: Product Name: Avnet On-Board Programmer
INFO:iMPACT - Digilent Plugin: Serial Number: 000000000000
INFO:iMPACT - Digilent Plugin: Product ID: F030012D
INFO:iMPACT - Digilent Plugin: Firmware Version: 011B
INFO:iMPACT - Digilent Plugin: JTAG Port Number: 0
INFO:iMPACT - Digilent Plugin: JTAG Clock Frequency: 4000000 Hz
-
“Initialize Chain” results:
Attempting to identify devices in the boundary-scan chain configuration...
INFO:iMPACT - Current time: 1/3/2012 11:07:54 AM
// *** BATCH CMD : Identify -inferir
PROGRESS_START - Starting Operation.
Identifying chain contents...'0': : Manufacturer's ID = Xilinx xc6slx9, Version : 0
INFO:iMPACT:1777 Reading C:/Xilinx/13.2/ISE_DS/ISE/spartan6/data/xc6slx9.bsd...
INFO:iMPACT:501 - '1': Added Device xc6slx9 successfully.
------------------------------------------------------------------------------------------------------------------------------------------done.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
// *** BATCH CMD : identifyMPM
-
“Cable Setup” results:
Enumerating cables. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusb_emb.sys found.
Driver version: src=1029, dest=1029.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug
31 2010 X86 32bit SYS 14:35:41, version = 1021.
PROGRESS_END - End Operation.
Elapsed time = 3 sec.
INFO:iMPACT - Digilent Plugin: found 1 device(s).
INFO:iMPACT - Digilent Plugin: opening device: "obp", SN:000000000000
INFO:iMPACT - Digilent Plugin: User Name: obp
INFO:iMPACT - Digilent Plugin: Product Name: Avnet On-Board Programmer
INFO:iMPACT - Digilent Plugin: Serial Number: 000000000000
INFO:iMPACT - Digilent Plugin: Product ID: F030012D
INFO:iMPACT - Digilent Plugin: Firmware Version: 011B
INFO:iMPACT - Digilent Plugin: JTAG Port Number: 0
INFO:iMPACT - Digilent Plugin: JTAG Clock Frequency: 4000000 Hz
-
“Read Device Status” results:
INFO:iMPACT - Current time: 1/3/2012 11:16:49 AM
// *** BATCH CMD : ReadStatusRegister -p 1
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': Reading bootsts register contents...
[0] VALID_0 - ERROR OR END OF STARTUP (EOS) DETECTED
:
1
[1] FALLBACK_0 - FALLBACK RECONFIGURATION ATTEMPT DETECTED
:
0
[2] RESERVED
:
0
[3] WTO_ERROR_0 - WATCHDOG TIME OUT ERROR
:
0
[4] ID_ERROR_0 - FPGA DEVICE IDCODE ERROR
:
0
[5] CRC_ERROR_0 - CYCLIC REDUNDANCY CHECK (CRC) ERROR
:
0
[6] VALID_1 - ERROR OR END OF STARTUP (EOS) DETECTED
:
0
[7] FALLBACK_1 - FALLBACK RECONFIGURATION ATTEMPT DETECTED
:
0
[8] RESERVED
:
0
[9] WTO_ERROR_1 - WATCHDOG TIME OUT ERROR
:
0
[10] ID_ERROR_1 - FPGA DEVICE IDCODE ERROR
:
0
[11] CRC_ERROR_1 - CYCLIC REDUNDANCY CHECK (CRC) ERROR
:
0
[12] STRIKE CNT - STRIKE COUNT FOR FALLBACK ATTEMPTS
:
0
[13] STRIKE_CNT - STRIKE COUNT FOR FALLBACK ATTEMPTS
:
0
[14] STRIKE_CNT - STRIKE COUNT FOR FALLBACK ATTEMPTS
:
0
[15] STRIKE_CNT - STRIKE COUNT FOR FALLBACK ATTEMPTS
:
0
'1': Reading status register contents...
[0] CRC ERROR
:
0
[1] IDCODE ERROR
:
0
[2] DCM LOCK STATUS
:
1
[3] GTS_CFG_B STATUS
:
1
[4] GWE STATUS
:
1
[5] GHIGH STATUS
:
1
[6] DECRYPTION ERROR
:
0
[7] DECRYPTOR ENABLE
:
0
[8] HSWAPEN PIN
:
1
[9] MODE PIN M[0]
:
1
[10] MODE PIN M[1]
:
1
[11] RESERVED
:
0
[12] INIT_B PIN
:
1
[13] DONE PIN
:
1
[14] SUSPEND STATUS
:
0
[15] FALLBACK STATUS
:
0