PRODUCT DATA SHEET
SUPERLIFE-316 Low VOC
10-1418 Stainless Steel Gray
DESCRIPTION
Superlife-316 is a single component, water-base acrylic emulsion coating
pigmented with alloy 316 stainless steel flake. It is non-flammable, low VOC, and
offers superb exterior durability. It has excellent adhesion and abrasion resistance.
USES
Superlife-316 DTMR, a liquid stainless steel coating that can be used as a direct to
metal primer and/or topcoat on properly prepared steel, galvanized steel, tin,
aluminum and concrete. It can also be used as a topcoat over primed steel
surfaces and most previously painted surfaces in corrosive atmospheres. It has
the ability to adhere to metal surfaces with slight contamination of oils or greases.
See surface preparation section below.
APPEARANCE
Low sheen metallic gray
RECOMMENDED PRIMERS
PrimeLock Low VOC Gray, Prime Solution 5250 Red/5253 Gray, Steel Plus Epoxy
Primer
PHYSICAL PROPERTIES
WEIGHT PER GALLON
SOLIDS BY WEIGHT
SOLIDS BY VOLUME
RECOMMENDED DFT
WFT TO ACHIEVE DFT
THEORETICAL
COVERAGE @1 MIL DFT
ACTUAL COVERAGE AT
RECOMMENDED DFT
DRY TIME @77OF
AND 50% HUMIDITY
HEAT RESISTANCE
OF DRIED FILM
SHELF-LIFE
PACKAGING
SURFACE PREPARATION
GENERAL
APPLICATION
THINING
ROLLER/BRUSH
AIR-ATOMIZED SPRAY
AIRLESS SPRAY
CLEANUP
9.7 Lbs
43.0%
33.4%
2.5 mils
7.5 mils
533 sq. ft./gal
213 sq. ft./gal
Tack Free: 30-45 minutes
Handle: 1 hour
Recoat: 1-2 hours
Full Cure: 7 days (can be accelerated)
400oF
2 year
1 gallon, 5 gallon and 55 gallon drum
Quality paint jobs occur with quality preparation, products and application. Quality
preparation includes cleaning the surface to be painted to remove all contaminants
by washing with BC4000 or other suitable cleaner. Thoroughly cured old coatings
may require scuff sanding for maximum adhesion.
Apply only when air and surface temperatures are between 50oF and 100oF and
surface temperature is at least 5oF above the dew point.
Use clean water. Thinning is normally not required. Use 5%-10% if needed
(approximately 1/2 pint per gallon)
Use clean water. Thinning is normally not required. Use 5%-10% if needed
(approximately 1/2 pint per gallon)
Use clean water. Thinning is normally not required. Use 5%-10% if needed
(approximately 1/2 pint per gallon)
Soap and water
EQUIPMENT RECOMMENDATION
FILTER
Use 50 mesh stainless steel screen or nylon bag when needed
BRUSH
Use quality synthetic bristle brush
ROLLER
Use quality roller cover
AIR ATOMIZED SPRAY
Follow equipment manufacturers nozzle and needle selection recommendation for
use with heavy latex paints. Spray at 45-60 psi.
2000-2500 psi with 0.017 to 0.021 tip.
100-120oF
AIRLESS SPRAY
HOT SPRAY
SAFETY INFORMATION
VOC
FLASH POINT
USDA
WARNING
100 g/L or .84 Lbs/gal
N/A
Authorized by USDS for use in federally inspected meat and poultry plants.
Do not take internally. Close containers tightly after use and keep upright. In case
of spillage, absorb and dispose of in accordance with locally applicable regulations.
California Prop 65 Warning: Detectable amounts of chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm, may be found
in this product or its vapor. For specific information refer to the Material Safety
Data Sheet(MSDS).
*** FOR INDUSTRIAL USE ONLY. KEEP OUT OF REACH OF CHILDREN. ***
Product Number
10-1418-01
10-1418-05
10-1418-55
PRODUCT ORDERING INFORMATION
Size
Weight/Case (Lbs)
Gallon
40
5 gallon
53
55 gallon
585
Case quantity
4
1
1
BURKE INDUSTRIAL COATINGS
6OO S 7th Place, Suite 108, Ridgefield, WA 98642
Phone: 360-887-8819 Toll Free: 800-348-3245 Fax: 360-887-8825
www.burkeindustrialcoatings.com
Date Revised: 11-16-2015