Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 4 MB
USB: scanning bus for devices...
Root Hub 0: 3 USB Device(s) found
Root Hub 1: 1 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Clearing DRAM........ done
BIST check passed.
1:00:00.0 Vendor/Device ID = 0x811210b5
1:01:07.0 Vendor/Device ID = 0xc72414e4
Boot Media: nand-flash usb
Net: octeth0
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (246092 bytes)
Loading .rodata @ 0x8f03c1c4 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f838 (16580 bytes)
Loading set_Xcommand_set @ 0x8f0438fc (104 bytes)
Loading .rodata.cst4 @ 0x8f043964 (20 bytes)
Loading .data @ 0x8f044000 (5620 bytes)
Loading .data.rel.ro @ 0x8f0455f4 (120 bytes)
Loading .data.rel @ 0x8f04566c (136 bytes)
Clearing .bss @ 0x8f0456f8 (11912 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console
Found compatible API, ver. 1.7
FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.7
(builder@shoth.juniper.net, Tue May 4 07:15:51 UTC 2010)
Memory: 1024MB
[14]Booting from nand-flash slice 4
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
\
can't load '/kernel'
can't load '/kernel.old'
Press Enter to stop auto bootsequencing and to enter loader prompt.
U-Boot 1.1.6-JNPR-1.7 (Build time: May 4 2010 - 06:59:58)
SRX_240_HIGHMEM board revision major:1, minor:45, serial #: AADS1327
OCTEON CN5230R-SCP pass 2.0, Core clock: 600 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM: 1024 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 4 MB
USB: scanning bus for devices...
Root Hub 0: 3 USB Device(s) found
Root Hub 1: 1 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Clearing DRAM........ done
BIST check passed.
1:00:00.0 Vendor/Device ID = 0x811210b5
1:01:07.0 Vendor/Device ID = 0xc72414e4
Boot Media: nand-flash usb
Net: octeth0
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (246092 bytes)
Loading .rodata @ 0x8f03c1c4 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f838 (16580 bytes)
Loading set_Xcommand_set @ 0x8f0438fc (104 bytes)
Loading .rodata.cst4 @ 0x8f043964 (20 bytes)
Loading .data @ 0x8f044000 (5620 bytes)
Loading .data.rel.ro @ 0x8f0455f4 (120 bytes)
Loading .data.rel @ 0x8f04566c (136 bytes)
Clearing .bss @ 0x8f0456f8 (11912 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console
Found compatible API, ver. 1.7
FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.7
(builder@shoth.juniper.net, Tue May 4 07:15:51 UTC 2010)
Memory: 1024MB
[15]Booting from nand-flash slice 4
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
\
can't load '/kernel'
can't load '/kernel.old'
Press Enter to stop auto bootsequencing and to enter loader prompt.
U-Boot 1.1.6-JNPR-1.7 (Build time: May 4 2010 - 06:59:58)
SRX_240_HIGHMEM board revision major:1, minor:45, serial #: AADS1327
OCTEON CN5230R-SCP pass 2.0, Core clock: 600 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM: 1024 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 4 MB
USB: scanning bus for devices...
Root Hub 0: 3 USB Device(s) found
Root Hub 1: 1 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Clearing DRAM........ done
BIST check passed.
1:00:00.0 Vendor/Device ID = 0x811210b5
1:01:07.0 Vendor/Device ID = 0xc72414e4
Boot Media: nand-flash usb
Net: octeth0
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (246092 bytes)
Loading .rodata @ 0x8f03c1c4 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f838 (16580 bytes)
Loading set_Xcommand_set @ 0x8f0438fc (104 bytes)
Loading .rodata.cst4 @ 0x8f043964 (20 bytes)
Loading .data @ 0x8f044000 (5620 bytes)
Loading .data.rel.ro @ 0x8f0455f4 (120 bytes)
Loading .data.rel @ 0x8f04566c (136 bytes)
Clearing .bss @ 0x8f0456f8 (11912 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console
Found compatible API, ver. 1.7
FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.7
(builder@shoth.juniper.net, Tue May 4 07:15:51 UTC 2010)
Memory: 1024MB
[16]Booting from nand-flash slice 4
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
\
can't load '/kernel'
can't load '/kernel.old'
Press Enter to stop auto bootsequencing and to enter loader prompt.
U-Boot 1.1.6-JNPR-1.7 (Build time: May 4 2010 - 06:59:58)
SRX_240_HIGHMEM board revision major:1, minor:45, serial #: AADS1327
OCTEON CN5230R-SCP pass 2.0, Core clock: 600 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM: 1024 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 4 MB
USB: scanning bus for devices...
Root Hub 0: 3 USB Device(s) found
Root Hub 1: 1 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Clearing DRAM........ done
BIST check passed.
1:00:00.0 Vendor/Device ID = 0x811210b5
1:01:07.0 Vendor/Device ID = 0xc72414e4
Boot Media: nand-flash usb
Net: octeth0
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (246092 bytes)
Loading .rodata @ 0x8f03c1c4 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f838 (16580 bytes)
Loading set_Xcommand_set @ 0x8f0438fc (104 bytes)
Loading .rodata.cst4 @ 0x8f043964 (20 bytes)
Loading .data @ 0x8f044000 (5620 bytes)
Loading .data.rel.ro @ 0x8f0455f4 (120 bytes)
Loading .data.rel @ 0x8f04566c (136 bytes)
Clearing .bss @ 0x8f0456f8 (11912 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console
Found compatible API, ver. 1.7
FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.7
(builder@shoth.juniper.net, Tue May 4 07:15:51 UTC 2010)
Memory: 1024MB
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
No bootable media found. Entering loader prompt.
loader> nextboot usb
Setting next boot dev usb
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
loader> reboot
Resetting...
U-Boot 1.1.6-JNPR-1.7 (Build time: May 4 2010 - 06:59:58)
SRX_240_HIGHMEM board revision major:1, minor:45, serial #: AADS1327
OCTEON CN5230R-SCP pass 2.0, Core clock: 600 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM: 1024 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 4 MB
USB: scanning bus for devices...
Root Hub 0: 4 USB Device(s) found
Root Hub 1: 1 USB Device(s) found
scanning bus for storage devices... 2 Storage Device(s) found
Clearing DRAM........ done
BIST check passed.
1:00:00.0 Vendor/Device ID = 0x811210b5
1:01:07.0 Vendor/Device ID = 0xc72414e4
Boot Media: nand-flash usb
Net: octeth0
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (246092 bytes)
Loading .rodata @ 0x8f03c1c4 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f838 (16580 bytes)
Loading set_Xcommand_set @ 0x8f0438fc (104 bytes)
Loading .rodata.cst4 @ 0x8f043964 (20 bytes)
Loading .data @ 0x8f044000 (5620 bytes)
Loading .data.rel.ro @ 0x8f0455f4 (120 bytes)
Loading .data.rel @ 0x8f04566c (136 bytes)
Clearing .bss @ 0x8f0456f8 (11912 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console
Found compatible API, ver. 1.7
FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.7
(builder@shoth.juniper.net, Tue May 4 07:15:51 UTC 2010)
Memory: 1024MB
[1]Booting from usb slice 2
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
Loading /boot/defaults/loader.conf
Unable to load a kernel!
\
can't load '/kernel'
can't load '/kernel.old'
Press Enter to stop auto bootsequencing and to enter loader prompt.
U-Boot 1.1.6-JNPR-1.7 (Build time: May 4 2010 - 06:59:58)
SRX_240_HIGHMEM board revision major:1, minor:45, serial #: AADS1327
OCTEON CN5230R-SCP pass 2.0, Core clock: 600 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM: 1024 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 4 MB
USB: scanning bus for devices...
Root Hub 0: 4 USB Device(s) found
Root Hub 1: 1 USB Device(s) found
scanning bus for storage devices... 2 Storage Device(s) found
Clearing DRAM........ done
BIST check passed.
1:00:00.0 Vendor/Device ID = 0x811210b5
1:01:07.0 Vendor/Device ID = 0xc72414e4
Boot Media: nand-flash usb
Net: octeth0
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (246092 bytes)
Loading .rodata @ 0x8f03c1c4 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f838 (16580 bytes)
Loading set_Xcommand_set @ 0x8f0438fc (104 bytes)
Loading .rodata.cst4 @ 0x8f043964 (20 bytes)
Loading .data @ 0x8f044000 (5620 bytes)
Loading .data.rel.ro @ 0x8f0455f4 (120 bytes)
Loading .data.rel @ 0x8f04566c (136 bytes)
Clearing .bss @ 0x8f0456f8 (11912 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console
Found compatible API, ver. 1.7
FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.7
(builder@shoth.juniper.net, Tue May 4 07:15:51 UTC 2010)
Memory: 1024MB
[2]Booting from usb slice 3
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
\
can't load '/kernel'
can't load '/kernel.old'
Press Enter to stop auto bootsequencing and to enter loader prompt.
U-Boot 1.1.6-JNPR-1.7 (Build time: May 4 2010 - 06:59:58)
SRX_240_HIGHMEM board revision major:1, minor:45, serial #: AADS1327
OCTEON CN5230R-SCP pass 2.0, Core clock: 600 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM: 1024 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 4 MB
USB: scanning bus for devices...
Root Hub 0: 4 USB Device(s) found
Root Hub 1: 1 USB Device(s) found
scanning bus for storage devices... 2 Storage Device(s) found
Clearing DRAM........ done
BIST check passed.
1:00:00.0 Vendor/Device ID = 0x811210b5
1:01:07.0 Vendor/Device ID = 0xc72414e4
Boot Media: nand-flash usb
Net: octeth0
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (246092 bytes)
Loading .rodata @ 0x8f03c1c4 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f838 (16580 bytes)
Loading set_Xcommand_set @ 0x8f0438fc (104 bytes)
Loading .rodata.cst4 @ 0x8f043964 (20 bytes)
Loading .data @ 0x8f044000 (5620 bytes)
Loading .data.rel.ro @ 0x8f0455f4 (120 bytes)
Loading .data.rel @ 0x8f04566c (136 bytes)
Clearing .bss @ 0x8f0456f8 (11912 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console
Found compatible API, ver. 1.7
FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.7
(builder@shoth.juniper.net, Tue May 4 07:15:51 UTC 2010)
Memory: 1024MB
[3]Booting from usb slice 1
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
Loading /boot/defaults/loader.conf
/kernel data=0xb096a4+0x1345dc syms=[0x4+0x8ae90+0x4+0xc9722]
Hit [Enter] to boot immediately, or space bar for command prompt.
Booting [/kernel]...
Kernel entry at 0x801000e0 ...
init regular console
Primary ICache: Sets 64 Size 128 Asso 4
Primary DCache: Sets 1 Size 128 Asso 64
Secondary DCache: Sets 512 Size 128 Asso 8
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
kld_map_v: 0x8ff80000, kld_map_p: 0x0
Copyright (c) 1996-2013, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
JUNOS 12.1X45-D15.5 #0: 2013-09-19 07:42:15 UTC
builder@svl-junos-pool92.juniper.net:/volume/build/junos/12.1/service/12.1X45-D15.5/objocteon/junos/bsd/kernels/JSRXNLE/kernel
JUNOS 12.1X45-D15.5 #0: 2013-09-19 07:42:15 UTC
builder@svl-junos-pool92.juniper.net:/volume/build/junos/12.1/service/12.1X45-D15.5/objocteon/junos/bsd/kernels/JSRXNLE/kernel
real memory = 1073741824 (1024MB)
avail memory = 509661184 (486MB)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
Security policy loaded: JUNOS MAC/pcap (mac_pcap)
Security policy loaded: JUNOS MAC/runasnonroot (mac_runasnonroot)
netisr_init: !debug_mpsafenet, forcing maxthreads from 4 to 1
cpu0 on motherboard
: CAVIUM's OCTEON 52XX CPU Rev. 0.8 with no FPU implemented
L1 Cache: I size 32kb(128 line), D size 8kb(128 line), sixty four way.
L2 Cache: Size 512kb, 8 way
obio0 on motherboard
uart0: <Octeon-16550 channel 0> on obio0
uart0: console (9600,n,8,1)
twsi0 on obio0
dwc0: <Synopsis DWC OTG Controller Driver> on obio0
usb0: <USB Bus for DWC OTG Controller> on dwc0
usb0: USB revision 2.0
uhub0: vendor 0x0000 DWC OTG root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
uhub1: vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 2
uhub1: single transaction translator
uhub1: 3 ports with 2 removable, self powered
umass0: STMicroelectronics ST72682 High Speed Mode, rev 2.00/2.10, addr 3
umass1: vendor 0x1005 USB FLASH DRIVE, rev 2.00/1.10, addr 4
dwc1: <Synopsis DWC OTG Controller Driver> on obio0
usb1: <USB Bus for DWC OTG Controller> on dwc1
usb1: USB revision 2.0
uhub2: vendor 0x0000 DWC OTG root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 1 port with 1 removable, self powered
cpld0 on obio0
pcib1: <Cavium on-chip PCIe HOST bridge> on obio0
Disabling Octeon big bar support
PCIe: Waiting for port 0 to finish reset
PCIe: Port 0 link active, 2 lanes
PCIe: Waiting for port 1 to finish reset
PCIe: Port 1 link active, 1 lanes
pcib1: Initialized controller
pci0: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> irq 0 at device 0.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <serial bus, USB> at device 2.0 (no driver attached)
pci1: <network> at device 7.0 (no driver attached)
pcib0: <Cavium on-chip PCIe HOST bridge> on obio0
pci2: <PCI bus> on pcib0
pci2: <processor> at device 0.0 (no driver attached)
gblmem0 on obio0
octpkt0: <Octeon RGMII> on obio0
cfi0: <AMD/Fujitsu - 4MB> on obio0
Timecounter "mips" frequency 600000000 Hz quality 0
###PCB Group initialized for udppcbgroup
###PCB Group initialized for tcppcbgroup
da1 at umass-sim1 bus 1 target 0 lun 0
da1: < USB FLASH DRIVE PMAP> Removable Direct Access SCSI-0 device
da1: 40.000MB/s transfers
da1: 1911MB (3913728 512 byte sectors: 255H 63S/T 243C)
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
Ignoring watchdog timeout during boot/reboot
Ignoring watchdog timeout during boot/reboot
Ignoring watchdog timeout during boot/reboot
Ignoring watchdog timeout during boot/reboot
umass0: BBB reset failed, TIMEOUT
Ignoring watchdog timeout during boot/reboot
Ignoring watchdog timeout during boot/reboot
umass0: BBB bulk-in clear stall failed, TIMEOUT
Ignoring watchdog timeout during boot/reboot
Ignoring watchdog timeout during boot/reboot
panic: Hardware watchdog timeout
cpuid = 0
KDB: stack backtrace:
SP 0: not in kernel
uart_z8530_class+0x0 (0,0,0,0) ra 0 sz 0
pid 22, process: idle: cpu0
###Entering boot mastership relinquish phase
KDB: enter: panic
[thread pid 22 tid 100008 ]
Stopped at
db> reset
breakpoint+0x4: jr
ra
U-Boot 1.1.6-JNPR-1.7 (Build time: May 4 2010 - 06:59:58)
SRX_240_HIGHMEM board revision major:1, minor:45, serial #: AADS1327
OCTEON CN5230R-SCP pass 2.0, Core clock: 600 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM: 1024 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 4 MB
USB: scanning bus for devices...
ERROR: CTL:TIMEOUT