Product Specification MHT1844M

advertisement
Product Specification MHT1844M
20th February 2014 Page 1 of 2
fibreflow Blown Fibre: Direct Bury, Metal-free, filled.
10mm and 12mm
GENERIC DETAILS:
MICRODUCTS (at 20C):
Primary m/d outer diameter, nom
Primary m/d inner diameter, nom
Primary m/d specification
Mass of individual primary m/d, nom
Max pull tension, single m/d
Load to cause 15% crush: typical
Min bend radius of primary m/d*
10.0mm
8.0mm
MHT 773
27g/m
200N (20kg)
200N
100mm
12.0mm (std)
10.0mm
MHT 2100
33g/m
240N (24kg)
370N
140mm
12.0mm (special)
9.4mm
MHT 1375
42g/m
300N (30kg)
500N
120mm
*This radius relates to the m/d capability only, and does not indicate a suitable radius for blowing fibre.
1.
2.
3.
M/ds are compatible with designated connectors.
Max air pressure for blowing, all m/ds: 15bar.
Storage of unprotected m/d: Indoors and well shielded from daylight.
INNER FILLER:
1. Filler thickness at m/d position 1.0mm nominal
2. Filler Removal: using ripcord provided (not shown on images).
PE OUTER SHEATH:
1. Sheath thickness is according to diameter.
2. The PE sheath shall be light stabilised and coloured (normally orange).
3. Normal printing includes product ident, metre marks and other data by arrangement.
4. Sheath Removal: using sheath removal tools, consult Emtelle or see website.
TUBE AND ASSEMBLY TESTS:
1. Crush test
2. Impact test:
3. Kink test:
4. Flexibility test:
test method IEC 60794-1-2-E3:
test method IEC 60794-1-2-E4:
test method IEC 60794-1-2-E10:
test method IEC 60794-1-2-E11:
Procedure to IEC 60794-5
Procedure to IEC 60794-5
Procedure to IEC 60794-5
Procedure to IEC 60794-5
This document is intended as a guide only. Whilst the information it contains is believed to be correct, Emtelle can take no responsibility for actions taken based on the
information contained in this document. Emtelle reserves the right to make changes to this document without notice. All sales of product are subject to Emtelle's terms and
conditions of sale only, which can be found on Emtelle's website.
This document is protected by copyright (c) Emtelle UK Limited [2009]. The products depicted are protected by intellectual property rights. Any unauthorized copying of this
document or of our products is prohibited and Emtelle UK Limited will take action to prevent any infringement of its rights and to claim damages for the loss that it suffers.
www.emtelle.com
Product Specification MHT1844M
20th February 2014 Page 2 of 2
PRODUCT-SPECIFIC DETAILS:
type
3DBfmf (10)
4DBfmf (10)
5DBfmf (10)
7DBfmf (10)
OD nom
mm
28.0
30.5
33.4
36.4
Outer Filler
Microduct
4/2.5
4/2.5
3/2.1
N/A
Mass nom
g/m
483
543
619
699
Min Bend
Rad mm*
420
520
570
620
Max Pull
force N**
2200
2400
2700
3000
Max Pull
force kg**
220
240
270
300
3DBfmf (12/10)
4DBfmf (12/10)
5DBfmf (12/10)
7DBfmf (12/10)
32.3
35.4
38.4
42.4
5/3.5
5/3.5
4/2.5
N/A
611
684
751
876
550
600
650
700
2600
2800
3300
3800
260
280
330
380
3DBfmf (12/9.4)
4DBfmf (12/9.4)
5DBfmf (12/9.4)
7DBfmf (12/9.4)
32.3
35.4
38.4
42.4
5/3.5
5/3.5
4/2.5
N/A
638
719
795
937
550
600
650
700
2800
3000
3600
4200
280
300
360
420
NOTES:
Bend Radius:
*These radius values relate only to the physical cable performance, not to recommended blowing
radii. See Installation manual for blowing advice.
Force:
** These products are normally buried, not pulled, but pulling is acceptable. After applying pulling
tensions, allow time for the pulled product to relax. See Installation manual.
Note 1: Diameters and thicknesses are measured to the nearest 0.1mm.
Note 2: ‘nominal’ data is based on middle-spec, and is for information only, not for inspection purposes.
Note 3: Sketches are for information purposes only, and should not be used for inspection.
Note 4: When interpreting performance data and installing m/ds, bundles, or fibre units, it is
assumed that the user has been trained by Emtelle.
Note 5: All data is believed to be accurate but
Note 6: Users must establish the suitability of these products for their own applications.
This document is intended as a guide only. Whilst the information it contains is believed to be correct, Emtelle can take no responsibility for actions taken based on the
information contained in this document. Emtelle reserves the right to make changes to this document without notice. All sales of product are subject to Emtelle's terms and
conditions of sale only, which can be found on Emtelle's website.
This document is protected by copyright (c) Emtelle UK Limited [2009]. The products depicted are protected by intellectual property rights. Any unauthorized copying of this
document or of our products is prohibited and Emtelle UK Limited will take action to prevent any infringement of its rights and to claim damages for the loss that it suffers.
www.emtelle.com
Download