Features of MTT Measurement and Test Laboratory (MTL): TEMPEST tests and measurements;
dangerous/hazardous electromagnetic emissions and acoustic impact research, measurement, and evaluation.
The MTT Measurement and Test Laboratory (MTL) is the only lab in Europe able to conduct all types of tests, evaluations, and measurements not only
of MTT developed and manufactured cryptographic equipment but third-party military and civil data transfer equipment (mobile phones, radio
transceivers, routers, switches, servers, displays, etc.).
The Measurement and Test Laboratory will be equipment with the field world-leading and most recent measurement equipment (Keysight,
Rohde&Schwarz, Bruel & Kjær). The measurement equipment manufacturers will perform constant service and technical support therefore ensuring
the measurement highest standards.
The Measurement and Test Laboratory enables to conduct TEMPEST compliance tests based on MTT-developed methods and technologies aimed at
confidential information leak prevention. The Lab constantly improves confidential information leak channel detection. The Lab results are used for
MTT cryptographic equipment development to resist hacker attacks and prevent confidential information leak in compliance with the TEMPEST.
Moreover, the Lab enables to test equipment for GSM, Bluetooth, and LTE standard compliance both at physical and protocol level. The Lab pays
special attention to equipment electromagnetic emissions analysis that may be hazardous for humans.
The Lab acoustic section enables to test and measure complete range of mobile voice communication devices acoustic properties as well as speech
transfer quality. This matter is critical for voice data channel security equipment development. The MTT topmost priority is the voice high quality and
high information security level.
The Measurement and Test Laboratory is based on … leased premises (occupying 140 m2). The Lab deployment term is three months. Lab personnel
consists of five highly qualified experts showing extreme expertise in modern measurement and test equipment, modern test methods, test results
preparation and processing in compliance with EU and US standards ensuring the production of high-quality telecommunication equipment.
The Measurement and Test Laboratory will comply with all ISO 27001 international standard requirements, therefore enabling to successfully pass
state certification in Switzerland.
Attachment 1: Measurement and Test Laboratory Equipment Cost
MTT Measurement and Test Laboratory Equipment List for Acoustic Measurements, Electromagnetic Compatibility Tests and Mobile
Device Standards Compliance Verification (ITU-T, MIL-STD, ETSI)
№
Name
1
R&S FSW spectrum analyzer
Qty
.
1
Price
(EUR)
100000
Subtotal
(EUR)
100000
2
R&S UPV audio analyzer
1
47000
47000
3
R&S SMA 100A signal
generator
Broadband radio
communication
tester R&S CMW500
Oscilloscope RTM2054
HM8112-3 multimeter
Universal anechoic screened
camera
1
28000
28000
1
380000
380000
1
1
1
23000
2000
405000
23000
2000
405000
Research of the examined product's temporary signal parameters
Research of electric signal parameters of the examined product
The screened anechoic camera is intended for measuring the electromagnetic
compatibility, measuring the electromagnetic fields (emission) from the
examined product and research of external electromagnetic impact on working
efficiency of the examined product.
8
Keysight N9038A measuring
receiver
1
95600
95600
9
N9038A-UK6 Commercial
calibration certificate with test
data
EM-Lab software complex
1
690
690
Execution of measurements on electromagnetic compatibility, measurements of
levels of electromagnetic fields (emission) in terms of compliance to
requirements of CISPR and MIL-STD, and execution of spectral analysis of
signals from the examined product in the screened anechoic camera in the range
of frequencies from 20Hz to 26GHz.
Execution of Keysight N9038A receiver calibration of t (p. 8)
1
4790
4790
4
5
6
7
10
Note
Research of the examined product's transceiver's quality parameters in terms of
compliance to GSM, Bluetooth, 802.11g/n standards.
Execution of voice quality research for an examined product on
recommendations of PESQMOS and POLQA.
Execution of acoustic tests and measurements, electromagnetic compatibility
tests
Research of the examined product's transceiver's quality parameters in terms of
compliance to GSM, Bluetooth, 802.11g/n standards.
Software for automation of measurements by the Keysight N9038A receiver (p.
8)
11
Set of Antennas on CISPR
11,15,22, GOST P
1
24600
24600
12
Set of Antennas on MILSTD461/state standard
specification PB6601
Automated ECU-6 complex
1
30700
30700
1
165000
165000
Acoustic camera Head and
Torso Test Enclosure (ETSLindgren)
Bruel & Kjaer 4128 Head and
Torso Simulator - HATS
1
250000
250000
1
110000
110000
16
Direct Current source for
mobile communication
devices with battery emulator
and 66321D voltmeter
2
3000
6000
17
Laptop (Core i3,
4GB RAM, 500GB HDD is
not worse)
Desktop computer
(Core i5, 8GB RAM is not
worse, than 1 TB HDD)
2
1300
2600
5
1000
5000
19
Accessories for measuring
equipment (adapters, cables,
connectors)
1
5000
5000
20
21
Printer/scanner/photocopier
PC desk
1
6
150
150
150
900
13
14
15
18
Execution of measurements of electromagnetic compatibility, measurements of
levels of electromagnetic fields (emission) in terms of compliance to the
requirements of CISPR 11,15,22, GOST P
Execution of measurements of electromagnetic compatibility, measurements of
levels of electromagnetic fields (emission) in terms of compliance to the
requirements of MIL-STD461/state standard specification PB6601
The automated complex for stability tests of resistance to electromagnetic
influence in term of IEC 61000-4-3, 3m 10B/m from 9kHz to 6 GHz
Execution of acoustic research of the examined product.
A simulator of a human torso and a head with an artificial ear and a mouth with
the generator of different types of acoustic signals and the software for the
analysis of acoustic characteristics of the examined product
Power supply of the tested product.
Organization and automation of electromagnetic compatibility testing, measuring
of electromagnetic fields, verification of compliance of the physical and protocol
layer to GSM, Bluetooth, WCDMA, 3GPP standards; acoustic tests.
Processing testing results in terms of electromagnetic compatibility, measuring of
electromagnetic fields, verification of compliance of the physical and protocol
layer to GSM, Bluetooth, WCDMA, 3GPP standards ; acoustic research.
Preparation of reports.
High-frequency cables, connectors, adapters for testing of a product for
electromagnetic compatibility, measuring of electromagnetic fields, verification
of compliance of the physical and protocol layer to GSM, Bluetooth, WCDMA,
3GPP standards.
Printout of reports and technical documentation.
22
23
24
Chair for PC operator
Tool kit
MTT Measurement and Test
Laboratory service, test, and
maintenance
TOTAL
8
1
1
150
100
30000
1200
100
30000
1717330
Installation and connection of the tested products to the metering equipment.
Annual MTT Lab measurement and test equipment service, test, and
maintenance expenses (by equipment suppliers or the certified organizations)