CRC FIPS Check on ramdisk partition SUCCESS All Good, loading
advertisement
CRC FIPS Check on ramdisk partition SUCCESS All Good, loading linux... ## Booting image at fd800000 ... Image Name: Linux-2.6.26-1.8.3-0 Created: 2011-09-28 12:35:28 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1429285 Bytes = 1.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Booting using the fdt at 0xfdb80000 Loading Device Tree to 007fe000, end 007ffbed ... OK Using Kilauea machine description Linux version 2.6.26-1.8.3-0 (root@p4.rnd.doremilabs.fr) (gcc version 4.0.0 (DENX ELDK 4.1 4.0.0)) #1 Wed Sep 28 14:35:15 CEST 2011 Zone PFN ranges: DMA 0 -> 65536 Normal 65536 -> 65536 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 65536 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: root=/dev/mtdblock0 selinux=1 audit=1 ip=42.0.0.1:42.0.0.6::255.255.255.248:clarity:eth0:off panic=1 console=ttyS0,115200 serialin=0 UIC0 (32 IRQ sources) at DCR 0xc0 UIC1 (32 IRQ sources) at DCR 0xd0 UIC2 (32 IRQ sources) at DCR 0xe0 PID hash table entries: 1024 (order: 10, 4096 bytes) clocksource: timebase mult[a00000] shift[22] registered Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256512k/262144k available (2800k kernel code, 5332k reserved, 112k data, 128k bss, 144k init) SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Mount-cache hash table entries: 512 net_namespace: 192 bytes NET: Registered protocol family 16 PCI: Probing PCI hardware NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order4: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 501 io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered pvr: 0x12911475 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0xef600200 (irq = 26) is a 16550A console [ttyS0] enabled serial8250.0: ttyS1 at MMIO 0xef600300 (irq = 16) is a 16550A ef600200.serial: ttyS0 at MMIO 0xef600200 (irq = 26) is a 16550A ef600300.serial: ttyS1 at MMIO 0xef600300 (irq = 16) is a 16550A brd: module loaded drivers/misc/ubootBootcountAccess.c (124) uboot_bootcount_init: created "/proc/driver/bootcount" PPC 4xx OCP EMAC driver, version 3.54 MAL v2 /plb/mcmal, 4 TX channels, 4 RX channels RGMII /plb/opb/emac-rgmii@ef600b00 initialized with MDIO support /plb/opb/emac-rgmii@ef600b00: input 0 in GMII mode eth0: EMAC-0 /plb/opb/ethernet@ef600900, MAC 00:06:4b:10:19:e5 eth0: found Marvell 88E1111 Ethernet PHY (0x01) fc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 fc000000.nor_flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Creating 8 MTD partitions on "fc000000.nor_flash": 0x00000000-0x01800000 : "ramdisk" 0x01800000-0x01c00000 : "linux" 0x01c00000-0x02b60000 : "nor_jffs2" 0x02b60000-0x02c60000 : "otp" 0x02c60000-0x03b60000 : "ramdisk_rescue" 0x03b60000-0x03f60000 : "linux_rescue" 0x03f60000-0x03fa0000 : "uboot_env" 0x03fa0000-0x04000000 : "uboot" Found 2 partitions NDFC NAND Driver initialized. Chip-Rev: 0x00000111 NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Number of partitions 2 Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit": 0x00000000-0x0c800000 : "secure_log" 0x0c800000-0x10000000 : "nand_jffs2" i2c /dev entries driver pcf8563 0-0051: chip found, driver version 0.4.2 pcf8563 0-0051: rtc core: registered pcf8563 as rtc0 ibm-iic ef600400.i2c: using standard (100 kHz) mode ibm-iic ef600500.i2c: using standard (100 kHz) mode ad7415(): temperature sensor driver initialized TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. eth0: link is down IP-Config: Complete: device=eth0, addr=42.0.0.1, mask=255.255.255.248, gw=255.255.255.255, host=clarity, domain=, nis-domain=(none), bootserver=42.0.0.6, rootserver=42.0.0.6, rootpath= VFS: Mounted root (cramfs filesystem) readonly. Freeing unused kernel memory: 144k init Empty flash at 0x023820dc ends at 0x02382800 Empty flash at 0x023849c0 ends at 0x02385000 Empty flash at 0x023870b8 ends at 0x02387800 Empty flash at 0x02389448 ends at 0x02389800 eth0: link is up, 1000 FDX, pause enabled Empty flash at 0x018a7434 ends at 0x0188a7800 Empty flash at 0x018adad8 ends at 0x018ae000 Empty flash at 0x018ae9b0 ends at 0x018af000 Empty flash at 0x018af9b0 ends at 0x018b0000 Empty flash at 0x030b3150 ends at 0x030b3800 Empty flash at 0x030bd480 ends at 0x030bd800 jffs2_scan_inode_node(): CRC failed on node at 0x046a57d4: Read 0xffffffff, calculated 0x3a1d101f Empty flash at 0x046a5d94 ends at 0x046a6000 Empty flash at 0x046b68b8 ends at 0x046b7000 Empty flash at 0x046bb934 ends at 0x046bc000 JFFS2 notice: (772) check_node_data: wrong data CRC in data node at 0x018ad59c: read 0xa8e7885d, calculated 0xbb84a593. JFFS2 notice: (772) check_node_data: wrong data CRC in data node at 0x030b2ae8: read 0x675afffb, calculated 0xf7fe722a. IMB driver version: 0.2.29. boot_file default load firmware /doremi/data/firmware/imb_firmware.bin (retries left 2) Loading firmware from file '/doremi/data/firmware/imb_firmware.bin' IMB: loading firmware: IMB-FW 30.07t-1. IMB: Firmware CRC is GOOD. IMB: Board revision: revE IMB: FPGA temp: 29. IMB: lock_security(), security lock. IMB: Codec: 0 is ADV212 IMB: Codec: 1 is ADV212 IMB: Codec: 2 is ADV212 IMB: Codec: 3 is ADV212 IMB: declare as SBC405 low profile. IMB: Tamper bus 0, events: high-temp: 0, low-temp: 0, oscillator: 0, TD1: 0, TD2: 0, TD3: 0, TD4: 0. IMB: Tamper bus 0, battery voltage: 3587 mV. IMB: Tamper bus 0, input voltage: 3308 mV. IMB: Tamper bus 0, output voltage: 3308 mV. IMB: Tamper bus 0, temperature: +29 C. IMB: Tamper bus 0, low-temperature threshold: -48 C. IMB: Tamper bus 0, high-temperature threshold: +94 C. IMB: Tamper bus 1, events: high-temp: 0, low-temp: 0, oscillator: 0, TD1: 0, TD2: 0, TD3: 0, TD4: 0. IMB: Tamper bus 1, battery voltage: 3609 mV. IMB: Tamper bus 1, input voltage: 3308 mV. IMB: Tamper bus 1, output voltage: 3308 mV. IMB: Tamper bus 1, temperature: +32 C. IMB: Tamper bus 1, low-temperature threshold: -48 C. IMB: Tamper bus 1, high-temperature threshold: +94 C. IMB: Service door closed! IMB: Physical marriage ok! [Dec 28 11:37:58 2014][INFO ]: --- timezone updated to -21600 seconds --[Dec 28 11:37:58 2014][INFO ]: ANSI PRNG selftest succeeded [Dec 28 11:37:58 2014][INFO ]: FIPS PRNG selftest succeeded [Dec 28 11:37:58 2014][INFO ]: SHA1 selftest succeeded [Dec 28 11:37:58 2014][INFO ]: HMAC selftest succeeded [Dec 28 11:37:58 2014][INFO ]: AES selftest succeeded [Dec 28 11:37:58 2014][INFO ]: DES selftest succeeded [Dec 28 11:37:58 2014][INFO ]: RSA selftest succeeded [Dec 28 11:37:58 2014][INFO ]: CRC selftest succeeded [Dec 28 11:37:58 2014][INFO ]: Media block selftest results: [Dec 28 11:37:58 2014][INFO ]: CRC seltest succeeded. [Dec 28 11:37:58 2014][INFO ]: firmware integrity seltest succeeded. [Dec 28 11:37:58 2014][INFO ]: FPGA AES seltest succeeded. [Dec 28 11:37:58 2014][INFO ]: -------[Dec 28 11:37:58 2014][INFO ]: Checking Ramdisk [Dec 28 11:37:58 2014][INFO ]: Checking ramdisk header: [Dec 28 11:37:58 2014][INFO ]: Ramdisk header check OK [Dec 28 11:37:58 2014][INFO ]: Checking ramdisk: [Dec 28 11:38:00 2014][INFO ]: Ramdisk check OK [Dec 28 11:38:00 2014][INFO ]: fips_check_ramdisk(): partition check OK [Dec 28 11:38:00 2014][INFO ]: -------[Dec 28 11:38:00 2014][INFO ]: Checking linux kernel [Dec 28 11:38:00 2014][INFO ]: Checking linux kernel header: [Dec 28 11:38:00 2014][INFO ]: Linux kernel hreader check OK [Dec 28 11:38:00 2014][INFO ]: Checking linux kernel: [Dec 28 11:38:00 2014][INFO ]: Linux kernel check OK [Dec 28 11:38:00 2014][INFO ]: Checking kernel DTB header: [Dec 28 11:38:00 2014][INFO ]: DTB header check OK [Dec 28 11:38:00 2014][INFO ]: Checking DTB: [Dec 28 11:38:00 2014][INFO ]: DTB check OK [Dec 28 11:38:00 2014][INFO ]: fips_check_linux(): partition check OK [Dec 28 11:38:00 2014][INFO ]: -------[Dec 28 11:38:00 2014][INFO ]: -------[Dec 28 11:38:00 2014][INFO ]: Checking ramdisk rescue [Dec 28 11:38:00 2014][INFO ]: Checking ramdisk header: [Dec 28 11:38:00 2014][INFO ]: Ramdisk header check OK [Dec 28 11:38:00 2014][INFO ]: Checking ramdisk: Enclosure Tamper battery voltage: 2943 mV [Dec 28 11:38:02 2014][INFO ]: Ramdisk check OK [Dec 28 11:38:02 2014][INFO ]: fips_check_ramdisk(): partition check OK [Dec 28 11:38:02 2014][INFO ]: -------[Dec 28 11:38:02 2014][INFO ]: Checking linux rescue kernel [Dec 28 11:38:02 2014][INFO ]: Checking linux kernel header: [Dec 28 11:38:02 2014][INFO ]: Linux kernel header check OK [Dec 28 11:38:02 2014][INFO ]: Checking linux kernel: [Dec 28 11:38:02 2014][INFO ]: Linux kernel check OK [Dec 28 11:38:02 2014][INFO ]: Checking kernel DTB header: [Dec 28 11:38:02 2014][INFO ]: DTB header check OK [Dec 28 11:38:02 2014][INFO ]: Checking DTB: [Dec 28 11:38:02 2014][INFO ]: DTB check OK [Dec 28 11:38:02 2014][INFO ]: fips_check_linux(): partition check OK [Dec 28 11:38:02 2014][INFO ]: -------[Dec 28 11:38:02 2014][INFO ]: Enclosure Monitoring enabled eth0: link is up, 1000 FDX, pause enabled Reconfigured eth0 to: eth0 Link encap:Ethernet HWaddr 00:11:1F:11:A2:21 inet addr:192.168.254.246 Bcast:192.168.254.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:588 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:35200 (34.3 KiB) TX bytes:0 (0.0 B) Interrupt:24 [Dec 28 11:38:02 2014][INFO ]: Starting smond.out [Dec 28 11:38:05 2014][INFO ]: Start '/doremi/bin/smd.out' [Dec 28 11:38:06 2014][INFO ]: Start '/doremi/bin/backplaned.out' IMB: Service door armed [Dec 28 11:38:07 2014][INFO ]: Start '/doremi/bin/clarity_driver.out' IMB: declare as SBC405 full profile. IMB: EDID is good. [Dec 28 11:38:08 2014][INFO ]: Start '/doremi/bin/cpmgrd.out' [Dec 28 11:38:09 2014][INFO ]: Start '/doremi/bin/spbmgrd.out' [Dec 28 11:38:10 2014][INFO ]: Start '/doremi/bin/marriaged.out' [Dec 28 11:38:11 2014][INFO ]: Start '/doremi/bin/smsd.out' [Dec 28 11:38:12 2014][INFO ]: Start '/doremi/bin/drmmcastd.out' [Dec 28 11:38:13 2014][INFO ]: Installed versions [Dec 28 11:38:13 2014][INFO ]: Uboot version : 2.0.7-0 [Dec 28 11:38:13 2014][INFO ]: Ramdisk version : 5.0.31-0 [Dec 28 11:38:13 2014][INFO ]: Ramdisk rescue version : 5.0.19-3 [Dec 28 11:38:13 2014][INFO ]: Kernel version : 1.8.3-0 [Dec 28 11:38:13 2014][INFO ]: Kernel rescue version : 1.8.3-3 [Dec 28 11:38:13 2014][INFO ]: Running software versions [Dec 28 11:38:13 2014][INFO ]: Kernel version : 2.6.26-1.8.3-0 [Dec 28 11:38:13 2014][INFO ]: Standard ramdisk version : 5.0.31-0 [Dec 28 11:38:13 2014][INFO ]: Board status [Dec 28 11:38:13 2014][INFO ]: Temperature [Dec 28 11:38:13 2014][INFO ]: RTC time : 28.500000 : 2014-12-28T17:38:13 [Dec 28 11:38:13 2014][INFO ]: System time : 2014-12-28T17:38:13 [Dec 28 11:38:13 2014][INFO ]: Boot count :1 [Dec 28 11:38:13 2014][INFO ]: Identity set : yes [Dec 28 11:38:13 2014][INFO ]: RTC intrinsic drift set : yes [Dec 28 11:38:13 2014][INFO ]: Clock set : yes [Dec 28 11:38:13 2014][INFO ]: Serial number : 238113 [Dec 28 11:38:13 2014][INFO ]: RTC intrinsic drift :6 [Dec 28 11:38:13 2014][INFO ]: Product name [Dec 28 11:38:13 2014][INFO ]: NAND smd partition [Dec 28 11:38:13 2014][INFO ]: NAND var partition [Dec 28 11:38:13 2014][INFO ]: Projector type [Dec 28 11:38:13 2014][INFO ]: Last reboot date : IMB : mounted : mounted : barco : 2012-11-02T18:03:03 [Dec 28 11:38:13 2014][INFO ]: Dolphin status [Dec 28 11:38:13 2014][INFO ]: Dolphin is running standard firmware [Dec 28 11:38:13 2014][INFO ]: Dolphin version : IMB-FW 30.07t-1 [Dec 28 11:38:13 2014][INFO ]: Dolphin rescue version : IMB-FW 99.03f-1 [Dec 28 11:38:13 2014][INFO ]: End of status [Dec 28 11:38:13 2014][INFO ]: smond.out started successfuly IMB: Marriage armed IMB: lock_security(), security unlock.
