SECTION 10 21 16.19
SHOWER AND TUB ENCLOSURES
Display hidden notes to specifier. (Don't know how? Click Here)
Copyright 2015 - 2015 ARCAT, Inc. - All rights reserved
PART 1 GENERAL
1.1
SECTION INCLUDES
A.
1.2
1.3
1.4
1.5
Shower and tub enclosures.
RELATED SECTIONS
A.
Section 06 10 00 - Rough Carpentry.
B.
Section 23 05 00 - Common Work Results for HVAC.
C.
Section 26 05 00 - Common Work Results for Electrical.
REFERENCES
A.
International Association of Plumbing and Mechanical Officials (IAPMO) IGC 154-2012 Shower and Tub/Shower Enclosures and Shower Panels.
B.
American Society of Mechanical Engineers (ASME) A112.18.1 - Plumbing Supply Fittings.
C.
Canadian Standards Association (CSA) B125.125.1-11 - Plumbing Supply Fittings.
D.
Uniform Plumbing Code - Canadian (cUPC).
SUBMITTALS
A.
Submit under provisions of Section 01 30 00 - Administrative Requirements.
B.
Product Data: Manufacturer's data sheets on each product to be used, including:
1.
Preparation instructions and recommendations.
2.
Storage and handling requirements and recommendations.
3.
Installation methods and diagrams.
C.
Selection Samples: For each finish product specified, two complete sets of color chips
representing manufacturer's full range of available colors and patterns.
D.
Verification Samples: For each finish product specified, two samples, minimum size 6 inches
(150 mm) square representing actual product, color, and patterns.
QUALITY ASSURANCE
A.
Manufacturer Qualifications: Minimum 5 year experience manufacturing similar products.
B.
Installer Qualifications: Minimum 2 year experience installing similar products.
10 21 16.19-1
C.
1.6
PRE-INSTALLATION MEETINGS
A.
1.7
1.8
Convene minimum two weeks prior to starting work of this section.
DELIVERY, STORAGE, AND HANDLING
A.
Deliver and store products in manufacturer's unopened packaging bearing the brand name
and manufacturer's identification until ready for installation.
B.
Handling: Handle materials to avoid damage.
PROJECT CONDITIONS
A.
1.9
Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and
application workmanship.
1.
Finish areas designated by Architect.
2.
Do not proceed with remaining work until workmanship is approved by Architect.
3.
Refinish mock-up area as required to produce acceptable work.
Maintain environmental conditions (temperature, humidity, and ventilation) within limits
recommended by manufacturer for optimum results. Do not install products under
environmental conditions outside manufacturer's recommended limits.
SEQUENCING
A.
Ensure that products of this section are supplied to affected trades in time to prevent
interruption of construction progress.
1.10 WARRANTY
A.
Manufacturer's standard published limited warranty provisions and term.
PART 2 PRODUCTS
2.1
2.2
MANUFACTURERS
A.
Acceptable Manufacturer: Transolid, a Division of Trumbull Industries, Inc., which is located
at: 400 Dietz Rd.; Warren, OH 44483; Toll Free Tel: 800-766-2452; Fax: 330-339-4426;
Email:request info (sales@transolid.com); Web:www.transolid.com
B.
Substitutions: Not permitted.
C.
Requests for substitutions will be considered in accordance with provisions of Section 01 60
00 - Product Requirements.
SHOWER AND TUB ENCLOSURES
A.
Shower Bases:
1.
Model: Single Threshold Custom Shower Base as manufactured by Transolid.
a.
Material: 100 percent solid surface exterior with reinforced composite substrate.
b.
Threshold: Standard 4 inches (102 mm).
c.
Threshold: Zero Roll-in 7/16 inch (11 mm).
d.
Size: Minimum - 26 inches (660 mm) x 32 inches (813 mm) Maximum - 36
inches (914 mm) x 42 inches (1067 mm).
e.
Size: Minimum - 38 inches (965 mm) x 32 inches (813 mm) Maximum - 48
inches (1219 mm) x 42 inches (1067 mm).
f.
Size: Minimum - 50 inches (1270 mm) x 32 inches (813 mm) Maximum - 60
inches (1524 mm) x 42 inches (1067 mm).
10 21 16.19-2
g.
2.
B.
Size: Minimum - 62 inches (1575 mm) x 32 inches (813 mm) Maximum - 72
inches (1829 mm) x 42 inches (1067 mm).
h.
Size: Minimum - 86 inches (2184 mm) x 32 inches (813 mm) Maximum - 96
inches (2438 mm) x 60 inches (1524 mm).
i.
Drain Location: As indicated or required.
j.
Finish: Bubble pattern texture.
k.
Color: White.
l.
Color: Biscuit.
m.
Color: Matrix Khaki.
Model: Single Threshold Decor Standard Shower Bases as manufactured by
Transolid.
a.
Material: 100 percent solid surface exterior with reinforced composite substrate.
b.
Threshold: Standard 4-1/4 inches (108 mm).
c.
Center Drain: 36 inches (914 mm) x 36 inches (914 mm) PAN3636SCC.
d.
Center Drain: 48 inches (1219 mm) x 34 inches (864 mm) PAN3448SCC.
e.
Tub Replacement End Drain Left (L) Drain: 60 inches (1524 mm) x 32 inches
(813 mm) PAN3260SLC.
f.
Tub Replacement End Drain Right (R) Drain: 60 inches (1524 mm) x 32 inches
(813 mm) PAN3260SRC.
g.
Neo Angle Center Drain: 36 inches (914 mm) x 36 inches (914 mm)
PAN3636NCC.
h.
Neo Angle Center Drain: 38 inches (965 mm) x 38 inches (965 mm)
PAN3838NCC.
i.
Neo Angle Center Drain: 42 inches (1067 mm) x 42 inches (1067 mm)
PAN4242NCC.
j.
Color: White A5.
k.
Color: Cameo A6.
l.
Color: Biscuit A7.
m.
Color: Moonlight A1.
n.
Color: Desert Earth A0.
o.
Color: Seaside A2.
p.
Color: Peppered Sage A3.
q.
Color: Sand Castle A4.
r.
Color: Matrix White A8.
s.
Color: Matrix Dusk B0.
t.
Color: Matrix Khaki B1.
u.
Color: Matrix Sand B2.
v.
Color: Matrix Summit B9.
Shower Bases, Direct-to-Stud/Remodel:
1.
Model: Slim Single Threshold ADA Shower Base - Collapsible Threshold as
manufactured by Transolid.
a.
Material, 100 percent solid surface exterior with reinforced composite substrate.
b.
1 inch (25 mm) collapsible bumper shall allow for wheelchair access into the
shower and protects the rest of the bathroom by containing water inside the
shower.
c.
Features a concealed drain with removable cover that brings both a design
element and comfort to your shower experience. Lift-off cover allows for easy
cleaning.
d.
Meets or exceeds the following specifications:
1)
IAPMO IGC 154-2012.
2)
ASME A112.18.1.
3)
CSA B125.125.1-11.
4)
cUPC.
5)
Shower Base shall be ADA-adaptable and shall comply with the
Americans with Disabilities Act when installed per requirements of the
10 21 16.19-3
2.
3.
2010 ADA Standards for Accessible Design, Section 608 Shower
Compartments, of the Act.
e.
10 Year Limited Residential Warranty / 3 Year Commercial Warranty.
f.
Size: 39-1/2 inches x 37-3/4 inches (1003 mmm x 959 mm) FC3938.
g.
Size: 63-1/2 inches x 37-3/4 inches (1613 mm x 959 mm) FC6338.
h.
Finish: 2-1/4 inches x 2-1/4 inches (57 mm x 57 mm) tile pattern.
i.
Color: 91 White Carrara.
j.
Color: 94 Sand Mountain.
k.
Color: 96 Almond Sky.
l.
Color: 01 White.
m.
Color: 86 Sea Shore.
Model: Slim Single Threshold ADA Shower Base - Trench Drain as manufactured by
Transolid.
a.
Material, 100 percent solid surface exterior with reinforced composite substrate.
b.
1/2 inch (13 mm) solid surface water retainer greatly improves trench drain
performance by directing majority of water to the central drain. Any remaining
water is easily corralled with the trench drain.
c.
Features a concealed drain with removable cover that brings both a design
element and comfort to your shower experience. Lift-off cover allows for easy
cleaning.
d.
Meets or exceeds the following specifications:
1)
IAPMO IGC 154-2012.
2)
ASME A112.18.1.
3)
CSA B125.125.1-11.
4)
cUPC
5)
Shower Base is ADA-adaptable and will comply with the Americans with
Disabilities Act when installed per requirements of the 2010 ADA
Standards for Accessible Design, Section 608 Shower Compartments, of
the Act.
e.
10 Year Limited Residential Warranty / 3 Year Commercial Warranty.
f.
Size: 39-1/2 inches x 37-3/4 inches (1003 mmm x 959 mm) FG3938.
g.
Size: 63-1/2 inches x 37-3/4 inches (1613 mm x 959 mm) FG6338.
h.
Finish: 2-1/4 inches x 2-1/4 inches (57 mm x 57 mm) tile pattern.
i.
Color: 91 White Carrara.
j.
Color: 94 Sand Mountain.
k.
Color: 96 Almond Sky.
l.
Color: 01 White.
m.
Color: 86 Sea Shore.
Model: Slim Single Threshold Retrofit Flush Mount Base as manufactured by
Transolid.
a.
Material, 100 percent solid surface exterior with reinforced composite substrate.
b.
1 inch (25 mm) solid surface water retainer "speed bump" directs water to the
drain and contains water inside shower.
c.
1-3/4 inches (44 mm) flat area in front of water retainer accommodates use of a
shower door.
d.
3/4 inch (19 mm) slim front edge provides flush mounting that would be level
with bathroom floor for easy walk-in entry.
e.
Features a concealed end drain with removable cover that brings both a design
element and comfort to your shower experience. Lift-off cover allows for easy
cleaning.
f.
Meets or exceeds the following specifications:
1)
IAPMO IGC 154-2012.
2)
ASME A112.18.1.
3)
CSA B125.125.1-11.
4)
cUPC.
5)
Shower Base shall be ADA-adaptable and shall comply with the
10 21 16.19-4
4.
C.
Americans with Disabilities Act when installed per requirements of the
2010 ADA Standards for Accessible Design, Section 608 Shower
Compartments, of the Act.
g.
10 Year Limited Residential Warranty / 3 Year Commercial Warranty.
h.
Size: Tub Replacement End Drain Left (L) Drain: 60 inches (1524 mm) x 32
inches (813 mm) FW6032L.
i.
Size: Tub Replacement End Drain Right (R) Drain: 60 inches (1524 mm) x 32
inches (813 mm) FW6032R.
j.
Finish: 2-1/4 inches x 2-1/4 inches (57 mm x 57 mm) tile pattern.
k.
Color: 91 White Carrara.
l.
Color: 92 Silver Mocha.
m.
Color: 94 Sand Mountain.
n.
Color: 96 Almond Sky.
o.
Color: 01 White.
p.
Color: 67 Matrix Khaki.
q.
Color: 08 Biscuit.
r.
Color: 86 Sea Shore.
Model: Slim Single Threshold Shower Base as manufactured by Transolid.
a.
Material, 100 percent solid surface exterior with reinforced composite substrate.
b.
Low threshold minimalist design is only 3 inches (76 mm) high for easy entry
and exit. Drain location: center, left or right hand as indicated or required.
c.
Features a concealed drain with removable cover that brings both a design
element and comfort to your shower experience. Lift-off cover allows for easy
cleaning.
d.
Meets or exceeds the following specifications:
1)
IAPMO IGC 154-2012.
2)
ASME A112.18.1.
3)
CSA B125.125.1-11.
4)
cUPC
e.
10 Year Limited Residential Warranty / 3 Year Commercial Warranty.
f.
Center Drain: 36 inches (914 mm) x 36 inches (914 mm) F3636.
g.
Center Drain: 48 inches (1219 mm) x 34 inches (864 mm) F3448.
h.
Center Drain: 60 inches (1524 mm) x 36 inches (914 mm) F6036.
i.
Tub Replacement End Drain Left (L) Drain: 60 inches (1524 mm) x 30 inches
(762 mm) F6030L.
j.
Tub Replacement End Drain Right (R) Drain: 60 inches (1524 mm) x 30 inches
(762 mm) F6030R.
k.
Tub Replacement End Drain Left (L) Drain: 60 inches (1524 mm) x 32 inches
(813 mm) F06032L.
l.
Tub Replacement End Drain Right (R) Drain: 60 inches (1524 mm) x 32 inches
(813 mm) F06032R.
m.
Finish: 2-1/4 inches x 2-1/4 inches (57 mm x 57 mm) tile pattern.
n.
Color: 91 White Carrara.
o.
Color: 92 Silver Mocha.
p.
Color: 94 Sand Mountain.
q.
Color: 96 Almond Sky.
r.
Color: 01 White.
s.
Color: 67 Matrix Khaki.
t.
Color: 08 Biscuit.
u.
Color: 86 Sea Shore.
Showers:
1.
Decor as manufactured by Transolid.
2.
Shower Walls - General:
a.
Material, 100 percent solid surface exterior with reinforced composite substrate.
b.
Walls shall be designed to be attached to moisture-resistant wall board, or
10 21 16.19-5
directly over tile with supplied adhesive. Walls shall be trimmable for custom fit.
Integrated pieces shall fit together for an easy, clean installation.
Three piece wall kit shall include two end walls, back wall and trim kit which
includes 2 corner cove molding pieces, 2 corner blocks, finish trim to fit along
the top of wall panels and down the outer sides to the shower base, one 11-oz.
tube color-matched caulk, three 11-oz. tubes 100% silicone adhesive and one
roll mounting tape.
e.
Color: A5 White.
f.
Color: A6 Cameo.
g.
Color: A7 Biscuit.
h.
Color: A1 Moonlight.
i.
Color: A0 Desert Earth.
j.
Color: A2 Seaside.
k.
Color: A3 Peppered Sage.
l.
Color: A4 Sand Castle.
m.
Color: A8 Matrix White.
n.
Color: B0 Matrix Dusk.
o.
Color: B1 Matrix Khaki.
p.
Color: B2 Matrix Sand.
q.
Color: B9 Matrix Summit.
r.
5 Year Limited Residential Warranty / 1 Year Commercial Warranty.
s.
Corner soap dish SOAPDISH03.
t.
Window trim kit WTK03636.
u.
Recessed shampoo caddy ACCESS0001.
v.
Recessed shampoo caddy ACCESS0002.
w.
Recessed shampoo caddy ACCESS0003.
x.
Double corner shelf ACCESS0004.
y.
Corner seat SEAT1818.
z.
Shower door.
Model: 36 inches (914 mm) x 36 inches (914 mm) Shower - WK363672/96 as
manufactured by Transolid.
a.
Shower Base: PAN3636SCC.
Model: 48 inches (914 mm) x 36 inches (914 mm) Shower - WK364872/96 as
manufactured by Transolid.
a.
Shower Base: PAN3448SCC.
Model: 60 inches (1524 mm) x 32 inches (813 mm) Shower - WK326072/96 as
manufactured by Transolid.
a.
Shower Base: PAN3260SLC/RC.
Model: 36 inches (914 mm) x 36 inches (914 mm) Neo-Angle Shower WK36NE72/96 as manufactured by Transolid.
a.
Shower Base: PAN3636NCC.
Model: 38 inches (965 mm) x 38 inches (965 mm) Neo-Angle Shower WK38NE72/96 as manufactured by Transolid.
a.
Shower Base: PAN3838NCC.
Model: 42 inches (1067 mm) x 42 inches (1067 mm) Neo-Angle Shower WK42NE72/96 as manufactured by Transolid.
a.
Shower base: PAN4242NCC.
Model: 60 inches (1524 mm) x 32 inches (813 mm) Bathtub Walls - WK326060/72 as
manufactured by Transolid.
c.
d.
3.
4.
5.
6.
7.
8.
9.
D.
Showers, Direct-to-Stud:
1.
Showers - General:
a.
Thick 1/4 inch (6 mm) 100% solid surface material bonded to a 1-1/4 inches (32
mm) thick aluminum honeycomb polyurethane filled backer for superior
strength. Solid surface material shall be easy to clean and shall not support
bacteria growth.
10 21 16.19-6
b.
2.
3.
4.
5.
6.
7.
8.
9.
10.
E.
Three-piece wall design glues directly to studs with supplied adhesive. Back
wall can be alternately installed with aluminum hanging rail provided.
c.
Aluminum channel joints for easy installation and uniform structure.
d.
Four wall shelves included for convenient storage.
e.
Dome top slides in place and sits on top of the shower walls forming a complete
8 feet (2438 mm) shower enclosure. The dome contains waterproof UL
approved 12 volt LED light(s) (40 year life).
f.
Meets or exceeds the following specifications:
1)
IAPMO IGC 154-2012.
2)
ASME A112.18.1.
3)
CSA B125.125.1-11.
4)
cUPC.
g.
10 Year Limited Residential Warranty / 3 Year Commercial Warranty.
h.
Finish: 16 inches x 16 inches (406 mm x 406 mm) square tile pattern.
i.
Transition Color: 91 White Carrara.
j.
Transition Color: 94 Sand Mountain
k.
Transition Color: 96 Almond Sky.
l.
Finish: Plain pattern.
m.
Plain Color: 01 White.
n.
Plain Color: 86 Sea Shore.
Model: 36 inches (914 mm) x 36 inches (914 mm) Shower - DKWF3668 as
manufactured by Transolid.
a.
Shower Base: F3636.
Model: 48 inches (914 mm) x 34 inches (864 mm) Shower - DKWF4848 as
manufactured by Transolid.
a.
Shower Base: F4834.
Model: 60 inches (1524 mm) x 30 inches (762 mm) Shower - DKWF6008 as
manufactured by Transolid.
a.
Shower Base: F6030L/R.
Model: 60 inches (1524 mm) x 32 inches (813 mm) Shower - DKWF6028 as
manufactured by Transolid.
a.
Shower Base: F6032L/R.
Model: 60 inches (1524 mm) x 36 inches (914 mm) Shower - DKWF6068 as
manufactured by Transolid.
a.
Shower Base: F6036.
Model: 39.5 inches x 37.75 inches (1003 mm x 959 mm) ADA Shower - DKWFG3988
(Trench Design) as manufactured by Transolid.
a.
Shower Base: FG3938.
Model: 39.5 inches x 37.75 inches (1003 mm x 959 mm) ADA Shower - DKWFC3988
(Collapsible Threshold) as manufactured by Transolid.
a.
Shower Base: FC3938.
Model: 63.5 inches x 37.75 inches (1613 mm x 959 mm) ADA Shower - DKWFG6388
(Trench Design) as manufactured by Transolid.
a.
Shower Base: FG6338.
Model: 63.5 inches x 37.75 inches (1613 mm x 959 mm) ADA Shower - DKWFC6388
(Collapsible Threshold) as manufactured by Transolid.
a.
Shower Base: FC6338.
Showers, Remodel:
1.
Showers - General:
a.
Thick 1/4 inch (6 mm) 100% solid surface material for superior strength and
easy cleaning. Surface shall not support bacteria growth.
b.
Walls shall be designed to be attached to moisture-resistant wall board, or
directly over tile with supplied adhesive. Walls are trimmable for custom fit.
c.
Integrated pieces shall fit together for an easy, clean installation.
d.
Two wall shelves shall be included for convenient storage.
10 21 16.19-7
e.
2.
3.
4.
5.
Wall kit includes two wrap around front edge trim pieces, front and side top
bullnose trim pieces with coped, mitered inside corners, two inside flat corner
molding pieces, one 1-oz. tube mounting adhesive, four 11-oz. tubes 100%
silicone adhesive and one roll mounting tape.
f.
10 Year Limited Residential Warranty / 3 Year Commercial Warranty.
g.
Extension wall panels add up to 24 inches (305 mm) of height to extend shower
walls to ceiling.
h.
Three wall pockets, horizontal, vertical or arched as indicated or required.
i.
Window trim kit.
j.
Finish: Subway or 16 inches x 16 inches (406 mm x 406 mm) tile pattern by
model.
k.
Transition Color: 11 Storm.
l.
Transition Color: 02 Cameo.
m.
Transition Color: 14 Sand.
n.
Transition Color: 05 Almond.
o.
Finish: Plain pattern.
p.
Plain Color: 01 White.
q.
Plain Color: 08 Biscuit.
r.
Plain Color: 67 Matrix Khaki.
s.
Plain Color: 86 Sea Shore.
Model: 36 inches (914 mm) x 36 inches (914 mm) Shower - RBE3667 as
manufactured by Transolid.
a.
Shower Base:F3636.
Model: 48 inches (914 mm) x 36 inches (914 mm) Shower - RBE4867 as
manufactured by Transolid.
a.
Shower Base: F4834.
Model: 60 inches (1524 mm) x 36 inches (914 mm) Shower - RBE6067 as
manufactured by Transolid.
a.
Shower Base: F6030L/R.
b.
Shower Base: F6032L/R.
c.
Shower Base: F6036.
Model: 60 inches (1524 mm) x 32 inches (813 mm) Tub Walls - RBE6026 as
manufactured by Transolid.
PART 3 EXECUTION
3.1
3.2
3.3
EXAMINATION
A.
Do not begin installation until substrates have been properly prepared.
B.
If substrate preparation is the responsibility of another installer, notify Architect of
unsatisfactory preparation before proceeding.
PREPARATION
A.
Clean surfaces thoroughly prior to installation.
B.
Prepare surfaces using the methods recommended by the manufacturer for achieving the
best result for the substrate under the project conditions.
INSTALLATION
A.
3.4
Install in accordance with manufacturer's instructions and in proper relationship with
adjacent construction.
PROTECTION
10 21 16.19-8
A.
Protect installed products until completion of project.
B.
Touch-up, repair or replace damaged products before Substantial Completion.
END OF SECTION
10 21 16.19-9