INFO
SERVICE
002/2014 - rev.0
NEW SHAFT ADAPTER FOR GEARBOX
ZF AS-TRONIC
with INTARDER 2 and INTARDER 3
D-21P-0-01 - Info Service PZB - rev.2
PZB is informing you that it has been defined and introduced a new adapter shaft, to fit
PTOs onto the ZF AS-TRONIC INTARDER 2 & 3.
Please refer to our documentation and our sales offices for ordering codes and parts
availability.
The use of this new adapter, on this family of transmissions, is strictly required due to
weaknesses of the Gearbox housing itself (please refer to ZF UFB L10/20 - Breakage at
PTO Installation Interface).
The adapter, due to its configuration, shares the load on the back-end of the gearbox case
on a much wider surface that reduces the stress concentration at the PTO mounting position
preventing any failure of the housing itself.
The new Adapter kit includes 5 off supplementary bolts (M12x35 - 8.8); 5 off washers; 1 off
adapter plate, 1 off Gasket; 1 off Bearing; 1 off quill-shaft and 1off circlip.
ADAPTER SHAFT
CODE
GEARBOX
205A683R000
ZF AS-TRONIC with INTARDER 2
205A743R000
ZF AS-TRONIC with INTARDER 3
MOUNTING
INSTRUCTIONS
See page 2
Interpump Hydraulics Spa a socio unico - Business Unit PZB
Sede Legale e Operativa: Via A. Mingozzi, 6 - 40012 Calderara di Reno (BO) - Italy
Tel.: +39 051 6460511 - Fax ITA: +39 051 6460565 - Fax EXPO: +39 051 6460560
E-mail ITA: venditeitalia@pzbitaly.com - E-mail EXPO: info@pzbitaly.com - Web: www.pzbitaly.com
Cap. Soc. Euro 2.631.600,00 i.v. - N. Mecc. BO 056383 - R.E.A. BO 444225 - C.F. 00883010241 - P.Iva IT02128140361
Soggetta ad attività di Direzione e Coordinamento da parte di Interpump Group Spa
Pag.
1/2
INFO
SERVICE
002/2014 - rev.0
MOUNTING INSTRUCTIONS
ADAPTER KIT FOR GEARBOXES
ZF AS-TRONIC with INTARDER 2 and INTARDER 3
5
4
3
2
6
1
B
7
A
Ø 68
8
A
Section A-A
265,55 (INTARDER 2)
278,25 (INTARDER 3)
B
273,3 (INTARDER 2)
286,0 (INTARDER 3)
REF.
1
D-21P-0-01 - Info Service PZB - rev.2
2
3
4
5
6
7
8
CODE
11305536000
11305594000
00701004000
12901574000
00802154000
10701571000
01001016000
00404002000
00106016000
DESCRIPTION
Shaft (for gearboxes with INTARDER 2)
Shaft (for gearboxes with INTARDER 3)
Circlip Seeger 45e UNI 7435
Gasket sp. 0,3 mm
O-Ring
Adapter
Bearing 6009/C3
Washer Schnorr 12 UNI 3703
Screw M12X35
QT.
1
1
1
1
1
1
5
5
- Set assembling operations in order to ensure that all the components are handled with the maximum
cleanliness as possible.
- Dismount the four bolts, the rear PTO opening cover and the plug located on top of the PTO
opening in order to feed the PTO with forced lubrication from the gearbox. Ensure that the adapter
fit properly onto the gearbox plane and in case needed remove the residual paint from the surface
of the transmission.
- Fit the pre-assembled shaft ref. 1 (including components ref. 2 and ref. 6) into the gearbox. Please
pay attention to properly align the shaft spline with the gearbox spline, the shaft must be installed
carefully without hammering on the shaft and has to be fitted by means of the hands only. In case
the shaft is not already pre-assembled, assemble first the circlip ref. 2 onto the shaft and secondly
the bearing ref. 6 using the proper tool in order to prevent any bearing damage.
- Fit the O-Ring ref. 4 on the adapter, the gasket ref. 3 and then the adapter on PTO mounting
surface of gearbox.
- Fit the five screws M12x35 ref. 8 (included in to this kit) together with washer ref. 7 in position ref.
B and tighten with a torque of 67 ± 7 Nm.
Interpump Hydraulics Spa a socio unico - Business Unit PZB
Sede Legale e Operativa: Via A. Mingozzi, 6 - 40012 Calderara di Reno (BO) - Italy
Tel.: +39 051 6460511 - Fax ITA: +39 051 6460565 - Fax EXPO: +39 051 6460560
E-mail ITA: venditeitalia@pzbitaly.com - E-mail EXPO: info@pzbitaly.com - Web: www.pzbitaly.com
Cap. Soc. Euro 2.631.600,00 i.v. - N. Mecc. BO 056383 - R.E.A. BO 444225 - C.F. 00883010241 - P.Iva IT02128140361
Soggetta ad attività di Direzione e Coordinamento da parte di Interpump Group Spa
Pag.
2/2