MODULE OBJECTIVES
After the completion of this module, student should be able to:

Identify different marking out tools and their usage.

Select the appropriate tool required for marking out.

Mark out work-pieces according to the dimensions given in engineering
drawings.

Distinguish the different hand tools and their uses.

Select the correct tool for the task.

State the care and safe use of hand tools.
3.1. INTRODUCTION TO MARKING OUT
Marking out is the process of transferring a design, layout
or dimensions from the drawing to a work-piece, and it is
considered as the first step in the manufacturing process.
COMMON MARKING OUT TOOLS
1- Scriber
2-Marking blue
3-Punch
4-Engineer’s square
5-Surface plate
6-Surface gauge
7-Angle plate
8-Vee block
9-Spring dividers
10- Ball peen hammer
1- SCRIBER
Scribers are used in metalworking to mark lines on work
pieces prior to manufacturing. They are used instead of
pencils as the marks from pencils can rub off easily.
Scribers consist of a rod of steel that has been sharpened to
a point at one or both ends and they are used to draw
shallow scratches on the surfaces of the work pieces.
There are 2 types of scribers
1- One-end scriber
2- Double-end scriber
2- MARKING BLUE.
Marking blue is a dye used in metalworking to aid in marking out.
It is used to paint a metal object with a very thin layer of dye that can
be scratched off using a scribers to show the bright metal
underneath.
The advantages of using the marking blue are:
 The existing scratches are covered with the dye.
 The new lines have a contrasting background.
3. PUNCH
The punch is a hard metal rod with a shaped tip at one end and a
rounded butt at the other end, which is usually struck by a
hammer.
The most commonly used ones for marking out are:
3-1-Center punch:
It is used as an aid to drilling operations. The center punch forms an
indent in which the tip of the drill fits. A center punch has a point
angle of 90°.
90°
3-1-Prick punch :
It is used to produce a smaller indentation than a center punch,
which acts as a useful datum (standard) point in layout operations.
A prick punch has a point angle of 60°.
60°
3-3- Letter stamps or number stamps:
These are used to print a letter or number into a work piece.
4. ENGINEER’S SQUARE
The engineer’s square is used for checking the straightness of a work
piece. It can also be used for marking perpendicular lines onto a
work piece.
DIFFERENT USES OF ENGINEER’S SQUARE
 Marking on Edges
 Marking on a side
 Checking outside corner
DIFFERENT USES OF ENGINEER’S SQUARE
 Checking inside corner
 Checking flatness
 Measuring short
distances
5. SURFACE PLATE
The surface plate has a high degree of flatness. The flat surface is
being used as a datum surface for marking out and for measuring
purposes. It is also called surface table if it can stand on the floor.
5.1 MAINTAINING THE SURFACE PLATE
 You should
1- Keep the surface in a good condition.
2- Keep the surface lightly oiled to prevent corrosion.
3- Take care when placing marking out tools on the surface.
 You should not
1- Place anything on the surface that would damage it.
2- Drop tools on the surface.
3- Hammer on the surface.
6. SURFACE GAUGE
A surface gauge is used on surface
plates for scribing lines on work
pieces and checking parallel surfaces
and heights.
The surface gauge is used
also in finding the center
of a cylinder and
determining whether a
plane's surface is truly
horizontal.
Checking parallel surfaces and heights
In the example shown the tilt screw was used to set the indicator
reading to zero on a gage block (not shown) of 0.375 inch
thickness. The gage block is then removed and the black part
shown is pushed forward so that the indicator stem rides up over it.
If the indicator reads zero then the part thickness is exactly 0.375..
If the indicator reads -0.002 then the part is 0.373 thick. If the
indicator reads +.002 then the part is 0.377 thick.
7. ANGLE PLATE
The angle plate is used to assist
in holding the work piece
perpendicular to the table.
The angle plate is provided
with holes and slots to
enable the secure
attachment, clamping and
adjusting of work pieces.
8. VEE BLOCK
The Vee blocks are generally used for holding circular work pieces for
marking out or machining.
9. SPRING DIVIDERS
The spring divider is used for scribing arcs or circles. The
below figure shows a circle that was marked by a
spring divider onto a work piece.
10. BALL PEEN HAMMER
The ball-peen hammer is shown in the figure. The crowned, or
rounded, edge (hemispherical head) works metal smoothly without
marking it. The other end of the hammer can be used to strike
punches and chisels