Take note that you need to have 3 designs in this semester: shafts, screws, and springs
A soft copy of 2D CAD, and Simulation will also be required. Use this format for your 3
designs.
Timeline for the submission of design
Checking for Design
Submission of Design
1st Design
By sched
October 8
2nd Design
By sched
November 12
3rd Design
By sched
December 10
Failure to submit the first design will not be able to proceed to 2nd design and 3rd design
Failure to submit the second design will not be able to proceed to 3rd design
Checking of Designs will be accommodated with prior schedule only.
Statement of the Problem
Put your problem statement here
Sketch of the Assembly (Not to Scale)
Design Computations
Given;
Type of driver =
Transmitted power
Voltage
Motor Speed
Speed reducer ratio = (if there is)
Driven = 85rpm
Required:
Design a chain drive transmission system for the installation.
Solution:
For Design Power,
Formula
Note: Since the driven machinery is the __________, the designer assumes that the
_____________________.
Find reference for your assumptions
Driving Source
Driven Machine
Thus;
Formula
Where;
XXXXXXX = XXXXXXXXXXXX
𝑠𝑢𝑏𝑠𝑡𝑖𝑡𝑢𝑡𝑖𝑜𝑛𝑠
𝐚𝐧𝐬𝐰𝐞𝐫𝐬
Guide in selecting pitch
900
Pmax =[ 𝑛 ]
2⁄
3
Where;
n = rpm of driving sprocket =
n = ooooo rpm
𝑜𝑜𝑜𝑜𝑜
𝑜𝑜𝑜𝑜𝑜
Thus;
900
Pmax = [ 𝑛 ]
2⁄
3
𝐏𝐦𝐚𝐱 = 𝐨𝐨𝐨𝐨𝐨𝐨 𝐢𝐧.
𝐏𝐦𝐚𝐱 > P - It means that in designing the roller chain,
????????????????????.
Solving for the number of teeth:
The designer assumes the no. of teeth for small sprocket = 000000000
From (find reference or site), with justification
By ratio and proportion,
nd = ND
d
D
N
ooooo
ooooo
= n = oooo = oooo
𝐧𝐨. 𝐨𝐟 𝐭𝐞𝐞𝐭𝐡 𝐨𝐟 𝐛𝐢𝐠 𝐬𝐩𝐫𝐨𝐜𝐤𝐞𝐭 = 𝐨𝐨𝐨𝐨𝐨
Include figures / illustrations
Find reference
Number of teeth on driving sprocket
Tooth correction factor
Thus; 𝐊 𝟏 = 𝟎𝟎𝟎𝟎𝟎
For selecting the chain number, include justification
Table taken from the web / book:
(put site / reference)
Input figure / illustration
The readings taken from the chart:
1. For _________ strand the chain number is _______________
2. For _________ strand the chain number is ____________
3. For ____________ strand the chain number is RC___________
Try ________________ with __________ strand;
Finding for Power Rating/Strand by Interpolation
Where: n = 0000000rpm
ANSI CHAIN NUMBER
Sprocket Speed rpm
show interpolation procedure
𝐑𝐚𝐭𝐢𝐧𝐠
𝐏𝐨𝐰𝐞𝐫 𝐒𝐭𝐫𝐚𝐧𝐝 = 0000000 hp/strand
Table _____________ Multiple-Strand Factors ___________________
K2
Number of Strands
Thus; 𝐊 𝟐 = 𝟎𝟎𝟎𝟎𝟎𝟎𝟎
For fully adjusted power rating
Fully Adjusted Power Rating = 𝑓𝑖𝑛𝑑 𝑓𝑜𝑟𝑚𝑢𝑙𝑎
Where:
K1 = 000000000000
K 2 = 0000000000000000
Rating
Power Strand = 0000000000 hp/strand
Fully Adjusted Power Rating = 𝑠𝑢𝑏𝑠𝑡𝑖𝑡𝑢𝑡𝑖𝑜𝑛
𝐅𝐮𝐥𝐥𝐲 𝐀𝐝𝐣𝐮𝐬𝐭𝐞𝐝 𝐏𝐨𝐰𝐞𝐫 𝐑𝐚𝐭𝐢𝐧𝐠 = 𝐚𝐧𝐬𝐰𝐞𝐫
Note: Try 1, 2, 3, & 4 strands
Justification in finding the type of RC and number of strands
Source of Table
RC
Pitch
Width
Min.
Average
Roller
Multiple
chain
Tensile
Weight
Diameter
Strand
No.
strength
Spacing
Insert figure / illurstration
Find site / reference for the chain type
Chain Pitch
Roller
no.
Pin
Roller link plate
diameter
Width Diameter
thickness
Table ______ Properties of Standard Roller Chains (Regular) taken from
_____by___________ pg.______
Chain
Pitch
A
B
C
no.
Solving for the pitch diameter of small sprocket;
d = 𝑓𝑜𝑟𝑚𝑢𝑙𝑎
Where;
Insert figure /
illustration
D
E
J
p = pitch = 00000
t = teeth of the driver = 00000
d = 𝑠𝑢𝑏𝑠𝑡𝑖𝑡𝑢𝑡𝑖𝑜𝑛
𝐝 = 𝐚𝐧𝐬𝐰𝐞𝐫
Solving for pitch diameter of big sprocket;
n
D
=d
N
D = 𝑓𝑜𝑟𝑚𝑢𝑙𝑎
Where;
d = diameter of small sprocket = 0000
n = revolution of the reducer = 0000
N = revolution of the driven = 00000
D = 𝑠𝑢𝑏𝑠𝑡𝑖𝑡𝑢𝑡𝑖𝑜𝑛
𝐃 = 𝐚𝐧𝐬𝐰𝐞𝐫
Solving for the Center Distance, C
C = 𝑓𝑜𝑟𝑚𝑢𝑙𝑎
Insert figure / illustration
Where;
Insert figure / illustration
d = diameter of small sprocket = 000000
D = diameter of big sprocket = 000000
C = 𝑠𝑢𝑏𝑠𝑡𝑖𝑡𝑢𝑡𝑖𝑜𝑛
𝐂 = 𝐚𝐧𝐬𝐰𝐞𝐫
Solving for the length of chain, L
L = 𝑓𝑜𝑟𝑚𝑢𝑙𝑎
Where;
no. of teeth of big sprocket = 000000
no. of teeth of small sprocket = 0000000
Insert figure / illustration
p = pitch = 0000000
C = Center Distance = 000000
L = 𝑠𝑢𝑏𝑠𝑡𝑖𝑡𝑢𝑡𝑖𝑜𝑛
𝐋 = 𝐚𝐧𝐬𝐰𝐞𝐫
From ____________________
It’s preferable to have an even number than to have an odd number of pitches for
roller chain so that the use of an offset connecting link will not be necessary. (you can
revise the justification depending on the necessity of your design)
For actual Center Distance of Chain
formula
Insert figure / illustration
substitution
𝑎𝑛𝑠𝑤𝑒𝑟
Solving for the diameter of shaft of the driver sprocket, 𝐃𝐬𝐡 ;
Dsh = 3
80Hp
(Taken from PSME CODE) you can use other resources
n1
Where;
Hp = driven transmitted power = 00000
Insert figure / illustration
N = rpm of small sprocket = 00000
Thus;
Dsh = 𝑠𝑢𝑏𝑠𝑡𝑖𝑡𝑢𝑡𝑖𝑜𝑛
Dsh = answer
From ____________ for ____________________
Say use: 𝐃𝐬𝐡 = 𝟎𝟎𝟎𝟎𝟎𝟎𝟎𝟎𝟎
Solving for the diameter shaft of the driven sprocket, 𝐃𝐛𝐡 ;
Dbh = 3
53.3Hp
(Taken from PSME CODE) you can use other resources
N
Where;
Hp = driven transmitted power = 30hp
N = rpm of big sprocket = 85 rpm
Insert figure / illustration
Thus;
Dbh = 𝑠𝑢𝑏𝑠𝑡𝑖𝑡𝑢𝑡𝑖𝑜𝑛
Dbh = answer
From ____________ for ____________________
Say use: 𝟎𝟎𝟎𝟎𝟎𝟎𝟎.
Solving for the Caliper Diameter
Note: since number of teeth is ___________________________.
Table ______________________
Caliper Diameter = Caliper factor x Pitch − Roller Diameter
Outside Diameter
No. Teeth
Pitch Diameter
Turned
Topping Hob
Cut
Solving for the Caliper Diameter of the Driver
Insert figure / illustration
Caliper Diameter of 𝐃𝐫𝐢𝐯𝐞𝐫 = source and formula
Where;
Caliper Factor
Pitch = 000000000in (source.)
Caliper Factor = 00000000000 (source)
Roller Diameter = 00000000 (source)
Thus;
Caliper Diameter = substitution
𝐂𝐚𝐥𝐢𝐩𝐞𝐫 𝐃𝐢𝐚𝐦𝐞𝐭𝐞𝐫 = 𝐚𝐧𝐬𝐰𝐞𝐫
Solving for the Caliper Diameter of the Driven
Insert figure / illustration
Use same procedures
Solving for the sprocket dimensions
From ___________________________________
Typical proportions for multiple strand roller chain sprocket
Formula for single strand
From _________________________________
Formula
Solving for the hub dimensions
Insert figure / illustration
For the small sprocket
Solving for the Hub diameter (𝐇𝐃 )
Solving for the Length of hub (L)
For the driven sprocket
Solving for the Hub diameter (𝐇𝐃 )
Solving for the Length of hub (L)
For C,
For C’
For E:
For F:
For G:
For R:
Refer to the figure.
From table ______________.
Std. Chain No.
Width of Chain, W
Maximum Sprocket
Flange Thickness , t
Single Strand
Sprocket Tooth Section Profile Dimension
Std.
Chain
Depth of
Width of
Minimum
Chain
Pitch, P
Chamfer,
Chamfer,
Radius,
h or c
g or e
Rc
no.
Transverse Pitch K
Standard
Heavy
Series
Series
Solving for the key dimensions
Insert figure / illustration
Justification for the type of key to be used
From ___________________________________________
Shaft Diameter
W
Note: all dimensions are all in inches
Solving for the bottom diameter of the sprocket, 𝐁𝐃
T
For the Driver:
𝐁𝐝 = 𝐏𝐝 − 𝐃𝐫 (taken from Kent’s Mechanical Engineers Handbook)
Where:
𝐏𝐝 = Pitch Diameter
𝐃𝐫 = roller Diameter
From __________________________
RC
Pitch
Width
Min.
Average
Roller
Multiple
chain
Tensile
Weight
Diameter
Strand
No.
strength
Spacing
Thus:
For the Driven:
𝐁𝐃 = 𝐏𝐃 − 𝐃𝐃 (taken from Kent’s Mechanical Engineers Handbook)
Where:
𝐏𝐝 = Pitch Diameter
𝐃𝐫 = roller Diameter
From _________________________
RC
Pitch
Width
Min.
Average
Roller
Multiple
chain
Tensile
Weight
Diameter
Strand
No.
strength
Thus:
Solving for pitch angle, θ:
From:
P
D = sinθ (taken from DOME by Faires, Pg. 464)
Where:
P = pitch
Diameter of the Driver =
Diameter of the Driven =
For driver:
P
sinθ = D
θ=
θ=
Spacing
For driven:
P
sinθ = D
θ=
θ=
Material for sprocket: __________________________
Include specification for the type of material and its table
----table----
The designer has chosen justification
Materials and Properties
Justification
Selection of Materials for Chain,
Material for chain:
Include table and specification
---table--The designer has chosen justification
Material used in Shaft: _______________:
Include table and specification
---table--The designer has chosen justification
SPECIFICATIONS
Type of motor
00000000
Transmitted power
00000000
Maximum pitch, Pmax
00000000
Service Factor, SF
00000000
Design Power
00000000
Power rating/stands
00000000
Tooth correction factor, k1
00000000
Number of strand
00000000
Chain number
00000000
Strand factor, k2
00000000
Fully adjusted power rating
00000000
Chain Pitch, P
00000000
Roller Diameter, RD
00000000
Length of chain, L
00000000
Center distance, C
00000000
Type of key
00000000
Width of chain
00000000
Flange thickness, t
00000000
Depth chamber, h
00000000
Width of chamber, g
00000000
Pin diameter, B
00000000
Thickness of link plates, H
00000000
For driven
Speed of sprocket, n
00000000
Number of teeth, t
00000000
Pitch diameter, PD
00000000
Bottom diameter, BD
00000000
Caliper diameter, CD
00000000
Shaft diameter, 𝐷𝑠
00000000
Width of key, b
00000000
Thickness of key, b
00000000
Length of key,
00000000
Length of hub, L
00000000
Hub diameter, HD
00000000
For driver
Speed of sprocket, N
00000000
Number of teeth, t
00000000
Pitch diameter, PD
00000000
Bottom diameter, BD
00000000
Caliper diameter, CD
00000000
Shaft diameter, 𝐷𝑠
00000000
Width of key, b
00000000
Thickness of key, b
00000000
Length of key,
00000000
Length of hub, L
00000000
Hub diameter, HD
00000000
BIBLIOGRAPHY
Include all references you have used