Deelan Chan 1918371
M15 Part Report
M15 - Laser Interference Part Report 2 – Introduction (Lasers in the Real World)
The laser. A technological milestone proposed in 1916 by Albert Einstein that identical
photons could be emitted in a simulated environment via excited molecules from a photon.
This was branded ‘negative absorption’ at the time. An idea not fully explored until 1951 by
Charles H. Townes and performed in 1954 where excited ammonia molecules were directed
into a resonance cavity. The oscillations came out at 24 GHz. 1960, the first laser, as we know
it, was designed and produced by Theodore Maiman. Lasers have found themselves in mass
use throughout the world, in many different industrial processes. Laser material processing
was one of the first industrial processes in which lasers were utilised. This worked via the
removal of material by evaporation which allowed much more precise cuts than a physical
piece of equipment. Another use in processing is the use for laser surface modifications.
There are many different lasers utilised, with different operating powers, modes and
durations.
One recent area of study by a team of scientists at the Toyohashi University of Technology,
has been the application and development of a ‘Q switch’ laser. This type of laser is used
quite commonly in surgical procedures as they can create a much cleaner and precise cut
than traditional surgical tools, while also doing less damage. The typical features of this type
of laser, is the minimal size but the very powerful beam it can emit. Q switching is a
technique which releases short, high powered outputs. The team at Toyohashi, utilised this
method, while also adjusting the magnetic material in which the laser beam will travel
through. The laser was also made to a tenth of the size of an American penny. The material
used in this case was a neodymium-yttrium-aluminium-garnet, which is a crystal used a as a
lasing medium. This combination of adjustments allowed the scientists to change the
polarisation of the laser, by manipulating the photons which produced the laser beam. A
smaller laser means that less energy is dissipated within the system during transmission and
more energy is pumped out of the system.
Another recent area of study has been the work done on the architecture for an electrically
pumped organic semiconductor laser diode. This technology is similar to the recent
advancement in technology where LED TV’s have progressed to the newer, more efficient
and vibrant OLED TV’s. The difference being the use of carbon-based organic materials rather
than the typical inorganic semiconductors used in LED’s. These OLED TV’s work by optical
pumping. In lasers, the laser diode must be electrically pumped, to allow integration into
visible and electrical circuits. This has been an obstacle, overcome by the research team at
the Centre for Organic Photonics and Electronics Research (OPERA), Kyushu University,
Japan. Due to the electrical contacts and surfaces, a lot of optical energy is lost. The team has
been working on a proper design for specific resonators and organic semi-conductors.
Observation of atomic diffraction with scattering from crystal surfaces, can be used to
demonstrate optical interferometry. This concept was also used to demonstrate that every
particle exhibits wave-like behaviours. The process of super-imposing two waves upon each
other where constructive and destructive interference can occur, is a demonstration of
optical interference. In constructive interference, a wave of greater amplitude is formed,
while in destructive interference, a wave of lesser amplitude is formed. The observation and
analysis of these interference patterns is called optical interferometry.
Deelan Chan 1918371
M15 Part Report
Within the M15 experiment, we were tasked with using a Michelson interferometer to test
the interference pattern. The Michaelson Interferometer works via splitting the laser beam
into two components. These two beams are then brought back together and recombined,
which will lead to interference. We will use this interferometer to find the fringe pattern,
which can then be used to work out the interference pattern when adjusting the delay of
each fringe test. Lasers are a good source of light for testing the interference pattern due to
its coherent, monochromatic and polarised nature.
1.
J Hecht, Short history of laser development (2010)
091002 doi.org/10.1117/1.3483597
2.
3.
R Poprawe, Tailored Light 2, Springer, Berlin, 2010. 9783642012372 (ISBN)
Roland W. Ohse, Laser application in high temperature materials, Great Britain, 1988.
9789290292401 (ISBN)
4.
Morimoto, R., Goto, T., Taira, T. et al. Randomly polarised beam produced by
magnetooptically Q-switched laser. Sci Rep 7, 15398 (2017).
https://doi.org/10.1038/s41598-017-15826-3
5.
Atula S. D. Sandanayaka et al. (2019) Indication of current-injection lasing from an
organic semiconductor. Appl. Phys. Express 12 061010. https://doi.org/10.7567/18820786/ab1b90
6.
Paul R. Berman, Atom Interferometry (1997), San Diego, USA, 0120924609 (ISBN)
7.
Department of Chemistry, University of Warwick. UK,
Year 1 Main Lab 15 (M15): The Michelson Interferometer