ECEN 103-003
Computer & Electronic Engineering Fundamentals
Laboratory Assignment 11
Branch Current and Nodal Analysis
Written by: Nate O’Connor
Partner: None
Department of Electrical and Computer Engineering
Peter Kiewit Institute
University of Nebraska
Date Performed: <MM/DD/YYYY>
Introduction
The point of this lab is to practice using branch current and nodal analysis on real life circuits and
Multisim circuits. To do this, we had to build a circuit in Multisim and in real life and then measure the circuit at
different points. This lab only took about an hour overall and was not too hard to complete. The following report
will go into detail on the background information needed to complete this lab, the procedure of the lab, and my
personal results from this lab.
Background
To complete this lab, you must know what branch current and nodal analysis are. They are two different methods for
measuring unknown currents and voltages. Branch current is used for measuring currents and voltage in every
branch of a circuit. To do this, you apply a different current to every branch of the circuit and then use Kirchoff's
Current Law and Kirchoff's Voltage Law to find the unknowns. Nodal analysis is where you pick a point or “node”
on the circuit and use Kirchoff’s Current Law at that node to find unknown voltages throughout the circuit. To be
able to use KCL and KVL, you must also know what they are. They are the same idea applied to two different units.
KVL states that the Voltage going into a closed loop must equal the voltage leaving a closed loop. In other words
the sum of all voltages is 0. When using branch analysis you are creating separate closed loops for each current, so
you can use KVL. KCL is the same idea but applied to current, it states that all current entering a node must equal
the current leaving a node. KCL uses the nodes instead of closed loops like KVL, this is why it is handy for nodal
analysis. Using these laws you can find certain values of voltage, current, or resistance at any point in the circuit.
They make it easier to break down and understand what is happening.
Procedure
To start you are going to need an electronics trainer, mutisim, a multimeter, a potentiometer, 5 resistors of
any resistance, and one 100ohm resistor. Start by creating the circuit seen in Figure 1 on the electronics trainer, the
100ohm resistor will be Rs, and E will be 12 volts, not 5. Using a multimeter, measure voltages at the 3 nodes (Va,
Vb, Vc), then using those voltages, calculate the resistance across each resistor. Record all data. Once that is
complete, create the exact same circuit in multisim, as seen in Figure 2, and measure every branch current as well
as the nodes (Va, Vb, Vc). Record the results and compare them to the real life measured results. Once that is
complete use branch current and nodal analysis to theoretically calculate the current and voltages, record results. For
the final part you must use the potentiometer. Replace R3 on your circuit with the 10k potentiometer. Place the
multimeter in series with R5 and set it to the current setting. Incrementally adjust the potentiometer until the current
on the multimeter reads as 0A, this means the bridge is balanced or equal on both sides so nothing runs through it.
Remove the potentiometer without adjusting the nob and measure its resistance. Record results.
2
Results
This lab was not a complete success for me. For IR5 I measured 0.00558A while multsim says it is –0.0038
and the theoretical calculation comes out to –0.0033. This means there is something wrong with my real-life
measurement. My assumption is that I either measured the wrong part of the circuit or that my multimeter probe was
also touching another wire, as all my resistor leads were very close together. Same with IR3, in real life I measured
0.025 while in multsim and theoretically, I measured 0.0141. This 0.025 value is the exact same as my IR1 value, so
this must be some human error on my part like improper calculation of I. Besides those disc
repancies, the other numbers lined up almost perfectly with the expect marginal difference between real-life
measurements and theory. A value of 330 ohms was need on the potentiometer to balance the bridge, meaning there
is no voltage difference on either side. This is due to the fact that R1,R2, and R4 are 330ohm resistors, meaning
there are two 330 ohm resistors on one side, while there is only one 330ohm resistor on the other side. To balance
this out I must add another 330 ohm resistor or chance the potentiometer value to 330ohms. It was very hard to get
the potentiometer right and my real life measurement was way off of 330ohms, I do not think I measured the
resistance correctly as it was at 9kohms, which makes no practical sense. All of these results are seen in Figure 3.
Conclusion
In conclusion this was a good lab for seeing Branch current and nodal analysis in practice instead of just
theory. While I had some issues arise, I feel they were due to human error rather than the design of the lab. This
report went over the background needed to complete this lab (KVL,KCL), the specific procedure to complete this
lab, and my own results.
3
Appendix
Figure 1: Real Circuit
Figure 2: Multisim Circuit
4
Figure 3: Results Table
5