Experiment No.: 01
POM Laboratory
Date of Experiment: 01/07/2025
ESC 2072
Properties of Materials
Determine and Compare the Resistivity of
Different Metals
NAME: WUJ Wickramasinghe
INDEX NO: EGT/23/575
INSTRUCTOR: Mr.Thadula
SESSION: Tuesday evening
SUBMISSION DATE:2025/07/25
Objectives
• To determine the resistivity of Constantan and Nichrome wires
Introduction and Theory
Electrical resistance and resistivity
Resistances (R): A measure of how difficult it is for electric current to flow through a
material. It is measured in ohms (Ω). The higher the resistance, the more difficult it is
for an electric current to flow through the material.
Resistivity(ρ): Resistivity is a measure of how much a material resists the flow of
electric current per unit length. It is measured in ohm-meters (Ω-m). The higher the
resistivity, the more difficult it is for electric current to flow through the material.The
resistivity of a material is a fundamental property of the material. It does not depend on
the length or cross-sectional area of the material.
Where:
•
•
•
•
R: Resistance(Ω)
ρ: Resistivity(Ω-m)
L: Length(m)
A: Cross sectional area(m2)
Figure 01: Material specimen dimensions that relate resistance to resistivity
Figure 02: Regimes of materials according to resistivity
Ohm’s Law
The current through a conductor between two points is directly proportional to the
voltage across the two points.
V∝I
V=IR
Where:
• V = voltage (V)
• I = current (A)
• R = resistance (Ω)
Factors affecting resistivity of metals
• The material of the conductor
• The temperature of the conductor
• The presence of impurities
Relationship between Resistance and Sample Dimensions
• Length: Resistance is directly proportional to the length of the conductor
(R∝L).
• Cross-Sectional Area: Resistance is inversely proportional to the crosssectional area (R∝1/A)
Conductivity (σ)
Material’s ability to conduct electric current. Inverse of resistivity.
Matthiessen’s Rule
The total resistivity of a metal is the sum of resistivity due to thermal vibrations,
impurities, and deformation.
Where:
• ρth = the resistivity due to temperature
• ρimp = the resistivity due to impurities
• ρdef = the resistivity due to defects
Materials and Instruments
•
•
•
•
•
•
•
•
Meter ruler
Power supply
1m Constantan & Nichrome wires
Micrometer screw gauge
Voltmeter
Ammeter
Connecting wires
Pencil jockey
Procedure
1. The given wire (Nichrome) was fixed along a meter ruler using tape or clips.
2. The diameter of the wire was measured at several points using a micrometer
screw gauge, and the average value was recorded.
3. The experimental circuit was set up as shown in the Figure 01, with the wire
connected in series to the power supply, ammeter, and connecting wires.
4. The voltmeter was connected in parallel across the portion of the wire between
the starting point and the pencil jockey.
5. The power supply was switched on, and the pencil jockey was placed at the
chosen mark (0.2m) on the wire.
6. The current (I) through the wire and the potential difference (V) across the
selected length were noted from the ammeter and voltmeter, respectively.
7. Steps 5 and 6 were repeated at 0.1m intervals of the wire.
8. The process was repeated for the Constantan wire.
9. Observations were recorded for both wires.
Figure 02: Circuit diagram
Calculation
For Nichrome wire,
• Diameter (Avg)
d=(d1+d2+d3)/3
d=(0.45mm+0.44mm+0.44mm)/3
d=0.443mm
• Resistant
R=V/I
For 0.2m,
Trial 1: R=5.10V/3.1A
R=1.65Ω
Trial 2: R=5.03V/3.13A
R=1.61 Ω
Trial 3: R=5.07V/3.14A
R=1.61 Ω
Resistance AVG= (1.65 Ω+1.61 Ω+1.61 Ω)/3
=1.62 Ω
Accordingly,
Length(m)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Trial 1
Resistance (Ω)
Trial 2
Trial 3
1.65
1.61
1.61
1.62
2.36
2.36
2.38
2.36
3.05
3.04
3.11
3.07
3.78
3.75
3.85
3.79
4.48
4.48
4.59
4.52
5.19
5.16
5.24
5.19
6.19
5.93
6.00
6.04
6.62
6.91
6.65
6.73
7.46
7.51
7.48
7.48
Resistance (Avg)Ω
Resistance vs Length(Nichrome)
y = 7.3134x + 0.1471
8.00
7.00
Resistance(Ω)
6.00
5.00
4.00
3.00
2.00
1.00
0.00
0
0.2
0.4
0.6
Length(m)
Gradient = 7.3134mΩ-1
Resistivity = (Resistance/Length) * Area
Since Resistance/Length = gradient,
Resistivity = Gradient*Area
ρ = 7.3134*(ϖd2/4)
ρ = 1.13 * 10-6Ωm
0.8
1
1.2
For Constantan wire,
• Diameter (Avg)
d=(0.44mm+0.45mm+0.45mm)/3
d=0.446mm
• Resistance
For 0.2m,
Trial 1: R=V/I
R=3.87V/5.01A
R=0.77Ω
Trial 2: R=5.01V/3.79A
R=0.75 Ω
Trial 3: R=5.01V/3.87A
R=0.77Ω
Resistance AVG= (0.77 Ω+0.75 Ω+0.77 Ω)/3
=0.77 Ω
Length(m)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Trial 1
Resistance (Ω)
Trial 2
Trial 3
0.77
0.75
0.77
0.77
1.05
1.06
1.14
1.08
1.37
1.42
1.37
1.39
1.71
1.67
1.80
1.73
2.02
2.00
1.95
1.99
2.25
2.30
2.29
2.28
2.56
2.56
2.54
2.55
2.92
2.87
2.89
2.89
3.16
3.28
3.19
3.21
Resistance(Avg)Ω
Resistance vs Length
y = 3.0155x + 0.1776
3.50
3.00
REsistance(Ω)
2.50
2.00
1.50
1.00
0.50
0.00
0
0.2
0.4
0.6
Length(m)
Gradient = 3.0115mΩ-1
Resistivity = (Resistance/Length) * Area
Since Resistance/Length = gradient,
Resistivity = Gradient*Area
ρ = 3.0115*(ϖd2/4)
ρ = 0.471* 10-6Ωm
0.8
1
1.2
Discussion
Measuring resistivity is used in real-world applications like engineering to select
materials, control the quality of products (electrical components), design heating
devices, and in thermocouples and sensors. It is also used for research and
development projects to improve performance in electronic devices.
Nichrome is a nickel-chromium alloy made with 80% Nickel and 20% chromium.
It has high resistivity at room temperature, a high melting point of around 1400 °C,
Corrosion and oxidation resistance, especially at high temperatures, stable mechanical
strength and ductility, and operates safely up to about 900°C. It is used for heating
elements for toasters, hair dryers, ovens, and industrial furnaces, laboratory wire loops
for flame tests, electric soldering irons, and hot-wire foam cutters.
Constantan is a copper-nickel alloy with 55% copper and 45% nickel prized for its
stable electrical resistivity across varying temperatures. Its low temperature coefficient
makes it ideal for precision resistors, thermocouples, and strain gauges. The alloy also
exhibits good corrosion resistance, ductility, and high-temperature durability, making it
useful in scientific and industrial measuring instruments.
Resistivity determines how strongly a material resists electric current. Lowresistivity materials like copper are used for efficient wiring, while high-resistivity alloys
like nichrome and constantan are used for heating elements and precision components.
Resistivity values are used by engineers to design safe, reliable circuits, preventing
overheating and energy loss in electrical systems.
Multimeters were used as an ammeter and a voltmeter to measure the current
and voltage of the circuit, allowing for the calculation of resistivity, as it is easy to obtain
accurate values.
While doing the practical, the pencil chalk was never dragged along the wire
because it can damage the wire, causing a reduction in diameter, which can be a reason
to increase resistance in the wire. And we start measuring from the 0.2m point to avoid
the high current flow due to low resistance, which can generate high heat.
We take 3 trials for each point to avoid errors during the measuring and improve
the accuracy. The pencil chalk was removed immediately after taking observations
because the current flow caused heat, and because of that, the resistance would
change.
Conclusion
The experiment successfully demonstrated the relationship between the length of
the conductor and the resistance. The resistivity of Nichrome was determined as 1.13 *
10-6Ωm and 0.471* 10-6Ωm for Constantan, with minor deviations between measured
and expected values attributed to real-world factors such as component tolerances and
measuring errors.
References
• Giancoli, D. C. (2005). Physics: Principles with applications (6th ed.). Pearson
Education.
• Serway, R. A., & Jewett, J. W. (2013). Physics for scientists and engineers with
modern physics (9th ed.). Brooks/Cole, Cengage Learning.
• Tipler, P. A., & Mosca, G. (2007). Physics for scientists and engineers: Extended
version (6th ed.). W. H. Freeman.
• Halliday, D., Resnick, R., & Walker, J. (2014). Fundamentals of physics (10th ed.).
Wiley.