EXP 16:
Hooke’s Law and Simple Harmonic Motion
Physic Lab I
Due Date: [redacted]
Statement of purpose:
To determine Hooke’s Law and Simple Harmonic Motion by testing rubber band and spring
elongation.
1
Data:
Data Table 1
2
Data Table 2
3
Data Table 3
4
Sample calculation:
Computed spring constant k:
k=
4 · π2
4 · (3.14)2
=
= 9.70 N/m
k
4.06
Percent difference (of k’s in B and C):
C −B
9.70 − 9.53
× 100% =
× 100% = 1.77%
(C + B)/2
(9.70 + 9.53)/2
Graph:
Answer the Question:
4. Interpret the x-intercept of the straight line of the T 2 versus m graph of part C.
5
6
When straight line of T 2 had change to be the x-intercept instead of y-intercept the value of
slope had decrease. [PORTION OF SPRING THAT MOVES UP AND DOWN, PORTION AT
DOWN. OSCILLATION has the same mass values?]
5. For a mass oscillating on a spring, at what positions do the (a) velocity (b) acceleration of
the mass have maximum values?
Velocity has maximum value at the middle of the displacement because the velocity at the upper
and lower limits of the displacement are zero and when they reach those points the velocity start
changing its direction and increasing its magnitude. However, the acceleration has its maximum
value at the upper and lower limits of the displacement because at those points the acceleration
is so strong that it change the direction of the velocity.
Analysis of data and summary of principles used:
An elastic material tends to return to its original form or shape after being deformed. Hence,
elasticity implies a restoring force that can give rise to vibrations or oscillations. The fact that for
many elastic substances the deformation is directly proportional to a restoring force that resists
the deformation was first demonstrated by Robert Hooke. Hooke’s law is expressed mathemat­
ically as F = −kx (with X0 = 0); where ∆x is the linear deformation or displacement of the
spring and X0 is its initial position. The minus sign indicates that the force and displacement
are in opposite directions. In term of Young’s modulus and stress and strain; Hooke’s law was
form F = (Y A/L0 ) ∆L. So, k = Y A/L0 and k called as spring constant.
The first experiment is the Rubber-Band Elongation; the rubber band was hung on a support
and suspend a weight hanger from it. It was added 150g to the weight hanger and record the
total suspended weight (m1g) in Data Table. Add appropriate 100g weights to the weight hanger
one at a time, and record the total suspended weight on the meter stick after each elongation
(y2,y3...). Then plot the total suspended weight force versus elongation position (mg versus y),
and draw an smooth curve that best fits the data points.
The second experiment is to test the spring elongation by repeat the same procedures above but
using the coil spring instead of the rubber band. After the procedure had done, plot the mg
versus y on the same sheet of graph paper used as above, and draw the straight line that best
fits the second data. Then determine the slope of the line (the spring constant k) and record in
the data table. And the slope of the line is 9.53(N/m).
The third experiment is to test the Period of Oscillation. On the weight hanger suspended from
the spring, place a 150kg mass prevent the spring from oscillation too fast and to prevent the
hanger from moving relative to the end of the spring during oscillations. When it is pulled down
10cm and released; record the total mass in Data Table 3. Using the laboratory stopwatch,
release the spring weight hanger from the predetermined initial displacement and determine the
time it takes for the mass to make 10 complete cycles. The same procedure was repeated by
adding 100kg for each time. After the procedure was repeated, calculated the average period
of each oscillation with its respective mass and plot a graph of average period squared versus
the mass, and draw the straight line that best fits the data to find the slope of the graph which
the slope of the graph come out to be 4.06 N/m. Finally compare this value of k with that
determined from the slope of the spring elongation graph by computing the percent difference
which come out to be 1.77 % difference.
The errors in this lab experiment was that the weights were not well calibrated. In addition we
are not considering the mass or weight of the spring which was affecting the system. Another
source of error was our inaccuracy to measure the elongation of the spring as well as the time
7
the spring took to complete 10 oscillations.
WHY WAS THIS EXPANDED ON ERRORS INACCURATE? [handwritten annotation]
EXPERIMENT 16
Hooke’s Law and Simple Harmonic Motion
Laboratory Report
Graph #2, #1
F(x) is a function of m. F = −k ∆L
L0
Fs
k = ∆L
, k = Newtons per meter [?]
A. Rubber-Band Elongation
DATA TABLE 1
8
B. Spring Elongation
DATA TABLE 2
k (slope of graph) (units)
Calculations (show work)
k = 1055 [units not fully specified — Don’t forget units]
Don’t forget units
(continued)
207
9