Investigating the IV Characteristics of Diodes Physics 444W: LabView Project Report Krish Patel March 29, 2026 Abstract Semiconductor based electronics form the basis of many modern technologies, and understanding their behavior is of significant importance to advancing these technologies. In this study, we explore the basics of the semiconductor physics underlying diodes. We derive the ideal diode equation from first principles, which describes the characteristic current-voltage (IV) curve of an ideal diode. We then measure the IV curve of a real diode, and compare it to the ideal equation; highlighting the assumptions of an ideal diode that a real-diode breaks. We explain how the real diode obeys the ideal diode equation closely except when reverse-biased, where leakage current plays a large role. We discuss how an understanding of these assumptions and their impact on the diode characteristics is essential for improving the quality of real diodes through the design and manufacturing process. 1 Introduction A diode is a type of electronic component that allows current to flow in only one direction. This unique property makes them a building block for many more complicated and extremely useful electronic devices and circuits. While early applications were based on vacuum tubes and thermionic emissions, semiconductor based diodes have become the most common and useful type in modern times. They are essential in most modern electronics, and thus a study of the underlying physics is crucial to advancing this technology. In this study, we aim to investigate the current-voltage (IV) curve of a real diode, comparing it to the ideal theoretical curve. Exploration of the theory builds a solid foundation of semiconductor physics and the working principles of diodes, while the investigation of a real diode allows us to understand the many engineering challenges in using real-diodes. Semiconductors are fundamentally defined as materials having the electrical conductivity between that of conductors and insulators. Silicon (Si) and germanium are the most common of these types of materials, both having 4 valence electrons. When these electrons remain bound to the lattice of atoms, within the chemical bonds, they are refereed to as valence electrons, while if they gain sufficient energy to ‘escape’ these bonds, such as by thermal excitation for example, they are free to float about in the lattice and conduct current; such electrons are referred to as free electrons. When a valence electron becomes a free electron, it leaves behind a vacancy, known as a hole, in the lattice of atoms. These holes can also effectively act as a conducting particle. Valence electrons neighboring the hole can occupy it, moving the vacancy around. The conductivity of semiconductors depends on the concentration of the charge carriers, free electrons and holes. Factors that can cause this concentration to change, by exciting valence electrons to become free electrons, include temperature and radiation. On an energy diagram, free electrons are said to exist in the conduction band while valence electrons are said to exist in the valence band, and these are separated by a energy band gap dependent on the material. The concentrations of these charge carriers ( we refer to holes as p, and electrons as n) can also be changed by a process known as doping, where another material with a different number of valence electrons is introduced in the semiconductor. p-type doping involves adding materials (such as boron) that have 3 valence electrons; this creates additional holes in the valence band because these materials can accept electrons from the bonds of other atoms. A p-type material generally has more holes than free electrons, and thus holes are known as the ”majority charge 1 carries” and free-electrons as the ”minority carriers”. Similarly, n-type doping involves adding materials with 5-valence electrons (such as phosphorous) which contribute their extra electrons to the conduction band and make free-electrons the majority carrier. Diodes contain both p-type and n-type materials, that are in contact at a p-n junction. It is the phenomena of the recombination of these charge carriers and diffusion that occurs here which gives rise to the unique one-way conduction properties of diodes. We expand upon the theory underlying p-n junctions in 2 and also derive the ideal diode equation, which describes the IV-characteristics of a perfect diode. 2 Theory 2.1 Background First, we introduce some preliminary equations, theory and notation that underpin the fundamentals of our derivation. We obtain the results first introduced by Shockley [4], but we follow closely the approach taken by [1]. • p refers to holes, while n refers to free electrons (electrons will also always refer to “freeelectrons” from now on). • The Boltzmann factor, given as E p(E) = exp − kB T (1) describes the probability of a particle being found at given state E when the system is at a constant temperature T , with kB being the Boltzmann constant. • ηi refers to the free-electron concentration in a pure semiconductor material at some temperature T . In a doped-material, we assume that the concentration of the dopant (ηN for n-type, ηP for p-type) is much greater than ηi , and thus the majority carrier concentration is approximately equal to the dopant concentration. For p-type, ηp ≈ NP and for n-type, nn ≈ nN . • The minority carrier concentration in a doped region can be determined from the majority carrier concentration and the equilibrium condition, given as ηp ηn = ηi2 . This condition stems from Boltzman statistics, using the factor described above. • We denote the equilibrium p and n concentrations in some material as ηp0 and ηn0 . When some process excites electrons and creates excess carriers beyond equilibrium, the excess concentrations are denoted as ∆n = ηn − ηno and ∆p = ηp − ηpo . • Excess electrons and holes (also known as ”electron-hole pairs”) will tend to spontaneously ∆p recombine, and this recombination rate is given as Un = ∆n τp in a n-type region, and Up = τn in a p-type region. The delta-term accounts for the excess concentration of the electron-hole pairs, while the τ term is the characteristic lifetime of the minority carrier, which is the average amount of time the electron-hole pair exists before recombining. • Lastly, dependent on the characteristic lifetime is the distance that a charge carrier moves due to diffusion, random motion p from region of high-concentration to low-concentration. This length scale is given as Lp = Dp τp for holes, where Dp is a characteristic diffusion constant, √ and Ln = Dn τn for electrons, with Dn defined similarly. We now have the tools necessary to derive the ideal-diode equation. Consider a n-doped region where the hole concentration has a gradient. These minority carriers will diffuse towards the region of lower concentration, creating a net-movement of charge and thus current. The rate of this movement will depend on the gradient [4], and thus this diffusion-current can be characterized as : dηp Jp (x) = −qp Dp ( ). (2) dx 2 Note that the negative sign accounts for the current movement (which is in the same direction as hole movement) in the direction opposite to the gradient, i.e, towards regions of lower ηp . Similarly, we have for electrons in a p-doped region: Jn (x) = qn Dn ( dηn ). dx (3) The negative sign is absorbed by the fact that conventional current is opposite to the direction of electron motion. We now want to model the concentration of minority carriers over time and space, as a partial differential equation. Consider a n-doped region of area A and infinitesmal thickness δx. The change in the number of holes in this volume is due to the diffusion current-flow, Jp , and recombination Up . Consider then, ∂(Aδxηp ) = Aq Jp (x) − Aq Jp (x + δx) − AδxUn ∂t −Aδx ∂Jp Aδx∆p ≈ − , q ∂x τp where the second equation comes from the definition of ∂J ∂x . We now divide by Aδx and subsitute for Jp (x) to get ∂ 2 ηp ∆p ∂ηp = Dp − ∂t ∂x2 τp =⇒ ∂∆p ∂ 2 ∆p ∆p = Dp − , ∂t ∂x2 τp (4) where we replace ηp by ∆p in the derivatives since they are only shifted by a constant factor ηp0 . Equation (5) is known as the minority carrier diffusion equation, for holes. where we are ignoring the generation of electron-hole pairs. A identical derivation for electrons in a p-doped region yields, ∂∆n ∂ 2 ∆n ∆n = Dn − . ∂t ∂x2 τn (5) We are now equipped to understand p-n junctions. These are regions where n-type and p-type materials touch, and intuitively, electrons from n-type and holes from the p-type material recombine upon contact. This creates a ”depletion region”, and this region is finite (i.e, recombination stops and the system attains equilibrium) because recombination causes charge accumulation (negative charges on the p-type side and positive on the n-type side) that creates an electric field, preventing more electron-hole pairs from diffusing across and recombining. Consider now, the characteristics of current flow across this p-n junction. The depletion region acts essentially as a barrier to current, because the electric field opposes the diffusion of any charge carriers across it. When a ”forward-bias” is applied, i.e the p-type region is at a sufficiently higher positive potential than the n-type region, the external voltage allows electrons and holes to overcome the depletion region’s opposing potential and diffuse across it, thus allowing current flow. Once electrons cross to the p-type region and thus holes to the n-type, they become minority carriers, and the magnitude of the total current is determined by how far these minority carriers are able to diffuse. Equations (5) and (4) may thus be used to determine the total current magnitude, as we shall do below. Note first, though, how the diode works when it is reverse-biased, i.e when the n-type material is at a higher voltage than the p-type. The majority carriers move away from the depletion region, essentially increasing the opposite charge accumulation and widening the depletion layer. This motion charges the depletion layer like a capacitor, but since no carriers cross the depletion layer there is no current flow. Finally, consider the n-type region of a forward biased diode, and the flow of the minority carriers (holes) in this region. Since we want to find the equilibrium current, we assume to be at a sufficiently large time-point when ∂∆p ∂t = 0. We are thus left with a boundary-value problem, 0 = Dp ∂ 2 ∆p ∆p − . ∂x2 τp 3 (6) The minority carrier concentration at the edge of the depletion layer is given by the law of the ). This stems from a consideration of Boltzman junction [4], defined as: ηp (0) = ηp0 exp( kqV BT statistics, with a larger forward bias resulting in an exponentially larger minority charge concentration. The value of ∆p at the boundary is then simply: ∆p(0) = ηp0 (exp( kqV ) − 1). BT (7) The other boundary condition we enforce is simply that ∆p doesn’t go to infinity as x → ∞, and this is a valid boundary condition assuming a thick diode. To solve the boundary value problem (6), second order linear ordinary differential equation, we use the method of the characteristic equation, guessing a solution of the form y = Aerx and substituting it into equation (6) to get: 0 = Aerx (Dp r2 − τ1p ). (8) The values of r satisfying this equation are r=± q 1 Dp τp = ±Lp . Note that to enforce the second boundary condition, only the negative value of r can be a valid solution. Thus we have, ∆p(x) = A exp( −x Lp ), (9) and the constant A is simply the value ∆p at x = 0 (7), giving the solution ∆p(x) = ηp0 (exp( qV −x ) − 1) exp( ). kB T Lp (10) An identical approach to solve the boundary-value problem for electrons in the p-doped region, with a new coordinate x′ = −x and the depletion region boundary still at x′ = 0 gives ∆n(x) = ηn0 (exp( −x′ qV ) − 1) exp( ). kB T Ln (11) Here we set the depletion region width to zero, which is valid because we assume that depletion region is thin enough for the current density to remain constant across it. Calculating the current from ∆p is straightforward, using the current density from equation (4) qV 1 −x ) − 1)( exp( )) kB T Lp Lp −x qp Dp ηp0 qV ) − 1) exp( Jp (x) = (exp( ), Lp kB T Lp Jp (x) = qp Dp ηp0 (exp( (12) and equivalently, Jn (x) = −qn Dn ηn0 qV −x′ (exp( ) − 1) exp( ) Ln kB T Ln (13) on the p-type side of the diode. Finally, we repeat the assumption that the depletion-layer is thin-enough for the current density to be constant across it, so that Jn (x′ = 0) = Jn (x = 0), and similar Jp (x′ = 0) = Jp (x = 0). The total current density at any point in the depletion layer, is then simply the sum of the 2 current densities given by equation (13) and (12), since they are flowing in the same direction. Thus, q D η Jnet = ( p Lpp p0 + =⇒ Inet = qA( qV qn Dn ηn0 ) (exp( ) − 1) Ln kB T qV Dp ηp0 D η + nLnn0 )(exp( ) − 1) Lp kB T Inet = I0 (exp( qV ) − 1) kB T 4 (14) where I0 is a collection of constants, referred to as the dark saturation current, or the leakage current. This value characterizes the small amount of charge that flows across the p-n junction, through the diffusion of minority-charge carriers, when the diode is reverse biased. By the conservation of charge, the value of current at one point in the circuit must be the current everywhere else also. We have thus used only the movement of the minority charges to determine the total current through the diode. Equation (14) is the ideal-diode law, also known as the “Shockley equation” [4], describing the IV-characteristics in an ideal setting. In the following sections, we will measure the IV characteristics of the real-diode and compare to the ideal-law. 3 Procedure Our experimental procedure consisted of a simple circuit, as shown in Figure 1. In practice, we measured the potential difference across a silicon diode (Vdiode ) and the potential difference of the alternating current (AC) source (Vsource ), and calculated the effective potential across the resistor (Vresistor ) using Kirchoff’s Laws. This was done because our data-measurement device, a National Instruments DAQ USB-6009, required a common ground signal for both input voltages to produce accurate readings. Using the potential across the resistor, we could calculate the current flowing through the diode. A sine wave, generated by a ET-1000 educational breadboard, was used as the AC source. A 4.7 kilo-Ohms resistor was used, and the circuit was constructed on the same breadboard. We measured the voltage every 100 milliseconds over a period of approximately 20 seconds using the DAQ-6009. This device was programmed using the National Instruments LabVIEWsoftware [2]. Figure 1: Circuit diagram representing the circuit implemented to measure the current and voltage across a real diode. 4 Results and Analysis We first aim to fit the ideal diode equation directly to our data, as shown in Figure 2 We observe that to a large extent, the real-diode behaves like expected, with current growing exponentially after a threshold positive voltage, and being small when the diode is reverse-biased. It appears that the diode’s intrinsic capacitance does not significantly hinder the quality of measured data. 5 Figure 2: Current-Voltage data for real diode, represented by the blue dots. The orange line represents the ideal diode equation plotted using the best fit parameters from the data, with the equation I = I0 exp(b V ), where I0 = (1.2 ± 0.5) × 10−9 )A and b = 21.8 ± 0.7 V−1 . The r2 score of the fit is 0.96. It is seen that the real leakage current is larger than the ideal-fit value, especially in the reverse-biased setting, and it grows with the magnitude of the reverse bias. This is a consequence of the real-diode not obeying many of the assumptions made in the derivation of the ideal-diode equation, such as constant current across a thin-depletion region. In a real-diode, recombination and pair-generation can occur within the depletion layer, allowing larger current to flow even in the reverse-biased state. Additionally, current can flow across the surface of the p-n junction of a real-diode, an effect that was ignored in the ideal setting. Lastly, thermal fluctuations can excite electrons and change the p-n concentrations, affecting the leakage current magnitude. These effects can be attributed to the quality of the diode we used. For a quantitative evaluation, we note that the fit produces a r2 score of 0.96, with the fitted parameters I0 = (1.2 ± 0.5) × 10−9 A, and b = kBq T = 21.8 ± 0.7V−1 . The order of magnitude of the dark-saturation current is an acceptable order of magnitude approximation [3]. The value of q suggested by the best-fit parameter b is q = 8.8 ± 0.3 × 10−20 C (with T=293 K), which is close to the actual charge of a single carrier (|q| ≈ 1.6 × 10−19 C for an electron) but not accurate. The larger value of charge suggests that the real-diode being tested likely allowed a non-significant amount of surface-current to leak across the p-n junction, which is reflected as a larger value of charge measured according to the ideal-diode equation. 5 Conclusion In this investigation, we have derived the ideal diode equation (14) by putting together first principles, such as conservation laws and Boltzmann statistics, into a boundary value problem. The current behavior of a forward biased diode is dominated by how the electrons and holes diffuse through the regions where they are minority carriers. The structure of the diode, and namely the p-n junction, prevents any current (expect the small leakage current due to diffusion) from flowing through a reverse-biased diode. The minority charge concentration at the boundary of the 6 depletion layer, in a forward-biased diode, grows exponentially with the applied voltage, and thus so does the net current through the diode. We also measure the IV curve of a real diode, showing how it closely fits to the ideal diode equation, especially in the forward-biased setting. The real diode has larger leakage current, possibly attributed to surface current leakage, thermal fluctuations, and non-constant current in the depletion layer. Future work may try to better fit the ideal diode equation to the real diode data using ideality factors and consideration of noise and leakage currents in the measurement instruments. The impact of temperature on the real diode IV curve and its resemblance to the ideal diode equation could also be an interesting field of study, since it would allow an understanding of the effect of thermal fluctuations on the diode. One may also attempt a similar investigation of other semiconductor based electronics, such as light emitting diodes (LEDs), photoresistors, and even operational amplifiers. References [1] Jed Brody. Physics 222 Lecture Notes. Lecture notes, Physics 222 , Emory University. 2022. [2] National Instruments. LabVIEW. Version 2022. 2022. url: https://www.ni.com/labview. [3] Kwok Kwok Ng and Simon M Sze. Physics of semiconductor devices. Wiley-Interscience Hoboken, NJ, 2007. [4] William Shockley. “The Theory of p-n Junctions in Semiconductors and p-n Junction Transistors”. In: Bell system technical journal 28.3 (1949), pp. 435–489. 6 Acknowledgements My lab partner was Andrew Kalish. I acknowledge the use of AI for asking conceptual questions about p-n junctions and diodes. However, the work produced above is completely of my own and not plagiarized in any form. 7
0
You can add this document to your study collection(s)
Sign in Available only to authorized usersYou can add this document to your saved list
Sign in Available only to authorized users(For complaints, use another form )