Section 1: Bleed Air & Pneumatic System
1. What is the primary source of high-pressure bleed air during low engine power settings
on the ground or in flight?
A. 6th stage compressor
B. High-Pressure (HP) engine compressor stage
C. APU compressor only
D. Low-Pressure (LP) turbine stage
2. Which valve closes automatically if a bleed leak is detected in the high-pressure bleed
line?
A. Crossbleed Valve (XBLEED)
B. Associated High-Pressure Bleed Valve (HPBV) and Engine Bleed Valve (EBV)
C. Emergency Ram Air Valve
D. Overboard Exhaust Valve (OEV)
3. What is the main function of the High-Pressure (HP) Bleed Valve during high-power
engine settings?
A. Opens to dump excess pressure overboard
B. Closes to allow the LP stage to supply bleed air efficiently
C. Modulates to control cabin temperature
D. Directs air exclusively to the anti-ice system
4. How does the Engine Bleed System maintain temperature limits prior to sending bleed
air to the ECS packs?
A. By mixing cold ram air directly into the ducting
B. Via the Precooler using engine fan bypass air
C. By cycling the pack flow control valves
D. Through electric duct heaters
5. Under what condition will the Overpressure Shutoff Valve (OPSV) automatically close?
A. When engine RPM drops below 50%
B. When downstream pneumatic line pressure exceeds safe operational limits
C. When cabin differential pressure reaches maximum
D. When ambient temperature drops below freezing
Section 2: Air Conditioning Packs & Temperature Control
6. What is the main function of the Primary Heat Exchanger in the ECS pack assembly?
A. To reheat air prior to entering the cabin
B. To provide initial cooling of high-temperature bleed air using ambient ram air
C. To strip moisture out of recirculated air
D. To regulate wing anti-ice pressure
7. What mechanism prevents icing inside the Condenser/Reheater section of the air
conditioning pack?
A. An electric heating element
B. The Anti-Ice Bypass Valve
C. Thermal insulation blankets
D. Continuous spray of hot bleed air
8. During single-pack operation in flight, how does the Air Management System (AMS)
controller adjust airflow?
A. Reduces flow to 50% to save fuel
B. Opens the Gasper valve to full
C. Increases airflow through the operating pack to High Flow mode
D. Shuts down cabin recirculation fans
9. What component modulates the bypass flow of hot air to adjust temperature in specific
conditioned air zones?
A. Overboard Exhaust Valve
B. Trim Air Valve (TAV)
C. Emergency Ram Air Valve
D. High-Pressure Bleed Valve
10. What is the physical location of the dual Air Conditioning Packs on the Embraer 170?
A. Tailcone area behind the pressure bulkhead
B. Forward cargo compartment floor
C. Wing-to-body fairing (belly fairing area) forward of the main landing gear well
D. Directly above the cockpit ceiling
Section 3: Cabin Pressure Control System (CPCS)
11. What is the primary role of the Outflow Valve (OFV) in the CPCS?
A. Directs fresh air into the cockpit
B. Modulates the exhaust of cabin air to maintain desired cabin pressure
C. Equalizes pressure between the forward and aft cargo bays
D. Supplies high-pressure air to the gasper outlets
12. How do the two automatic channels of the CPCS Controller operate?
A. Both run simultaneously at all times
B. They alternate automatically after each flight cycle
C. Channel A handles climb; Channel B handles descent
D. Channel B only activates during single-pack operations
13. At what cabin altitude will the CPCS trigger a CABIN ALTITUDE HIGH warning
message on the EICAS?
A. $8,000\text{ ft}$
B. $9,700\text{ ft}$ (or $10,000\text{ ft}$ depending on software standard)
C. $12,500\text{ ft}$
D. $14,000\text{ ft}$
14. What is the purpose of the Negative Pressure Relief Function built into the Outflow
Valve assembly?
A. Prevents ambient pressure from exceeding cabin pressure by more than $0.5\text{ psi}$
B. Increases cabin climb rate during emergency descents
C. Releases pressure from the water storage tanks
D. Dumps cabin pressure rapidly when landing gear touches down
15. What happens when the CPCS DUMP switch on the overhead panel is pressed?
A. Opens all cargo doors automatically
B. Depressurizes the cabin at $1,200\text{ ft/min}$ up to $12,400\text{ ft}$, turns off packs and
recirc fans
C. Deploys the Ram Air Turbine immediately
D. Closes the Outflow Valve completely
Section 4: Avionics & Emergency Systems
16. How many cooling fans are assigned to the Forward Avionics Compartment?
A. 1
B. 2
C. 3
D. 4
17. Which set of conditions automatically configures Electronic Rack Ventilation into
'Flight Mode'?
A. Engine 1 ON and APU BLEED switch OFF
B. Altitude $> 10,000\text{ ft}$ and speed $> 200\text{ kts}$
C. TLA $> 60^{\circ}$ and parking brake released
D. Main gear squat switch in AIR mode only
18. What proportion of fresh vs. recirculated air is maintained by the cabin distribution
system under normal conditions?
A. 70% fresh / 30% recirculated
B. 52% fresh / 48% recirculated
C. 40% fresh / 60% recirculated
D. 100% fresh air
19. Under what specific conditions will the AMS open the Emergency Ram Air Valve?
A. Cabin altitude $> 10,000\text{ ft}$
B. Altitude $< 25,000\text{ ft}$ and failure of both Air Conditioning Packs
C. Ground operation with ambient temperature $> 40^{\circ}\text{C}$
D. Whenever the APU Bleed is unavailable in flight
20. What is the fail-safe position of the Emergency Ram Air Valve upon total loss of
electrical power?
A. Open
B. Closed
C. Modulating
D. Half-open position
21. Where is the ground high-pressure air connector located on the E170?
A. Right-hand wing-to-body fairing
B. Left-hand wing-to-body fairing
C. Aft fuselage near the APU inlet
D. Nose landing gear wheel well
22. If the APU is supplying bleed air on the ground and Engine 1 is started, how does the
AMS manage the APU Bleed Valve?
A. Keeps it open to assist with pack operation
B. Closes it automatically during engine start to prevent backflow
C. Modulates it to half-open position
D. Opens the Crossbleed Valve automatically
23. What triggers a BLEED 1(2) LEAK EICAS message?
A. Overpressure in the high-stage compressor line
B. Continuous loop sensing of high temperature along the bleed ducting
C. Failure of the Precooler temperature sensor
D. Opening of the Overpressure Shutoff Valve
24. The Precooler regulates downstream bleed air temperature to approximately what
target under normal conditions?
A. $120\,^\circ\text{C}$
B. $200\,^\circ\text{C}$
C. $280\,^\circ\text{C}$
D. $350\,^\circ\text{C}$
Section 2: Packs & Temperature Control Logic
25. What happens to the Pack Valves during an engine start sequence in flight?
A. Both remain open at normal flow
B. They close automatically to provide maximum air for engine start
C. They switch to High Flow mode
D. Emergency Ram Air opens automatically
26. What component regulates water drainage from the water separator/collector back into
the ram air duct?
A. High-Pressure Bleed Valve
B. Water Injector / Spray Nozzle
C. Gasper Fan
D. Recirculation Shutoff Valve
27. What is the primary function of the Condenser in the air conditioning pack?
A. To heat ram air before it enters the heat exchanger
B. To cool the air leaving the compressor stage so moisture condenses out
C. To prevent cabin air from entering the avionics compartment
D. To regulate the ground air conditioning connection
28. If the Temperature Controller loses all cabin temperature selector inputs, how does it
control zone temperature?
A. Shuts down both packs immediately
B. Drives the trim air valves to 100% open
C. Maintains a fixed default supply temperature schedule
D. Opens the emergency ram air valve
Section 3: CPCS & Pressurization Scenarios
29. What happens if the pilot sets the CPCS mode to MANUAL and uses the manual
control switch?
A. Channel A continues to run in the background
B. DC electrical power directly drives the manual motor on the Outflow Valve
C. The AMS overrides manual inputs above $25{,}000\text{ ft}$
D. The DUMP switch functionality is disabled
30. What is the maximum differential pressure ($\Delta P$) permitted under normal
operating schedules at high altitude (above $37{,}000\text{ ft}$)?
A. $7.77\text{ psid}$
B. $8.32\text{ psid}$
C. $8.80\text{ psid}$
D. $9.10\text{ psid}$
31. How does the CPCS prevent cabin pressure altitude from exceeding structural limits if
both auto channels fail?
A. Mechanical safety relief valves open at maximum differential pressure
B. The APU starts automatically to add pressure
C. The Emergency Ram Air valve opens
D. The Gasper shutoff valve closes
32. What causes the Cabin Altitude logic to enter "Aborted Takeoff Mode"?
A. Parking brake set while engines are running
B. Throttle retarded to idle before takeoff velocity/liftoff while cabin is pre-pressurized
C. Engine failure on takeoff roll
D. Rapid loss of bleed pressure below $1{,}000\text{ ft}$
Section 4: Avionics Cooling & Cargo Ventilation
33. How does the Forward Avionics Cooling system behave when the aircraft is in flight
and ambient temperature is very low?
A. Both Fan 1 and Fan 2 run at maximum speed
B. System switches to natural convection / differential pressure driving flow, saving fan wear
C. Heated bleed air is injected directly into the racks
D. Middle Avionics Fan 3 takes over all cooling
34. What is the purpose of the Smoke Evacuation Mode in the avionics ventilation system?
A. Reverses fan direction to push smoke into the cargo bay
B. Closes supply valves and opens the Overboard Exhaust Valve to draw smoke out
C. Directs gasper air into the electronic racks
D. Increases recirculation fan speed to filter smoke through HEPA filters
35. If cargo fire system bottle 1 is discharged into the Forward Cargo Bay, what signals the
cargo fan to stop?
A. Smoke detector / Fire protection system signal to the AMS
B. High temperature sensor in the aft bulkhead
C. CPCS DUMP switch activation
D. Manual toggle on the maintenance panel
36. Where is the Gasper Air Fan physically located?
A. In the nose landing gear bay
B. In the aft equipment bay / air conditioning bay area
C. Inside the cockpit center pedestal
D. In the tailcone next to the APU
Section 5: Distribution & Maintenance Operations
37. Which EICAS message indicates that a HEPA recirculation filter is clogged or
restricted?
A. RECIRC FAN FAIL
B. RECIRC FILTER AIRFLOW / Maintenance status message
C. PACK 1 OVHT
D. RAM AIR OPEN
38. What is the default position of the Check Valves in the cabin recirculation line?
A. Spring-loaded closed (opens with airflow)
B. Motor-driven fully open
C. Solenoid-latched closed
D. Variable position modulated by AMS
39. During a dual pack failure scenario at $18{,}000\text{ ft}$, what provides fresh air to
the cabin?
A. APU compressor automatically
B. Emergency Ram Air Valve opening due to system logic
C. Outflow valve fully open
D. Cargo ventilation fan operating in reverse
40. Why must maintenance personnel inspect duct tie-down straps during structural or
ECS checks?
A. To ensure electrical grounding of the carbon fiber ducts
B. To prevent duct movement, disconnection, or chafing against surrounding aircraft structure
C. To measure duct internal pressure limits
D. To calibrate the trim air valve position sensors
Question
#
Correct Answer
1
B — High-Pressure (HP) engine compressor stage
2
B — Associated High-Pressure Bleed Valve (HPBV) and Engine Bleed
Valve (EBV)
3
B — Closes to allow the LP stage to supply bleed air efficiently
4
B — Via the Precooler using engine fan bypass air
5
B — When downstream pneumatic line pressure exceeds safe operational
limits
Question
#
Correct Answer
6
B — To provide initial cooling of high-temperature bleed air using ambient
ram air
7
B — The Anti-Ice Bypass Valve
8
C — Increases airflow through the operating pack to High Flow mode
9
B — Trim Air Valve (TAV)
10
C — Wing-to-body fairing (belly fairing area) forward of the main landing
gear well
11
B — Modulates the exhaust of cabin air to maintain desired cabin pressure
12
B — They alternate automatically after each flight cycle
13
B — $9,700\text{ ft}$ (or $10,000\text{ ft}$ depending on software
standard)
14
A — Prevents ambient pressure from exceeding cabin pressure by more than
$0.5\text{ psi}$
15
B — Depressurizes the cabin at $1,200\text{ ft/min}$ up to $12,400\text{
ft}$, turns off packs and recirc fans
16
B — 2 (Fan 1 and Fan 2)
17
C — TLA $> 60^{\circ}$ and parking brake released
18
B — 52% fresh / 48% recirculated
19
B — Altitude $< 25,000\text{ ft}$ and failure of both Air Conditioning
Packs
20
B — Closed (spring-loaded to closed position)
21
A — Right-hand wing-to-body fairing
22
B — Closes it automatically during engine start to prevent backflow
Question
#
Correct Answer
23
B — Continuous loop sensing of high temperature along the bleed
ducting
24
B — $200\,^\circ\text{C}$
25
B — They close automatically to provide maximum air for engine start
26
B — Water Injector / Spray Nozzle
27
B — To cool the air leaving the compressor stage so moisture condenses
out
28
C — Maintains a fixed default supply temperature schedule
29
B — DC electrical power directly drives the manual motor on the
Outflow Valve
30
B — $8.32\text{ psid}$
31
A — Mechanical safety relief valves open at maximum differential
pressure
32
B — Throttle retarded to idle before takeoff velocity/liftoff while cabin
is pre-pressurized
33
B — System switches to natural convection / differential pressure
driving flow, saving fan wear
34
B — Closes supply valves and opens the Overboard Exhaust Valve to
draw smoke out
35
A — Smoke detector / Fire protection system signal to the AMS
36
B — In the aft equipment bay / air conditioning bay area
37
B — RECIRC FILTER AIRFLOW / Maintenance status message
38
A — Spring-loaded closed (opens with airflow)
39
B — Emergency Ram Air Valve opening due to system logic
Question
#
Correct Answer
40
B — To prevent duct movement, disconnection, or chafing against
surrounding aircraft structure
Here are 20 additional multiple-choice questions focusing on more detailed component
operations, system logic, and maintenance scenarios for the Embraer 170 Environmental Control
System.
E170 ECS Multiple-Choice Quiz (Part 2)
Section 1: Pneumatics & Bleed Air System
21. Where is the ground high-pressure air connector located on the E170?
A. Right-hand wing-to-body fairing
B. Left-hand wing-to-body fairing
C. Aft fuselage near the APU inlet
D. Nose landing gear wheel well
22. If the APU is supplying bleed air on the ground and Engine 1 is started, how does the
AMS manage the APU Bleed Valve?
A. Keeps it open to assist with pack operation
B. Closes it automatically during engine start to prevent backflow
C. Modulates it to half-open position
D. Opens the Crossbleed Valve automatically
23. What triggers a BLEED 1(2) LEAK EICAS message?
A. Overpressure in the high-stage compressor line
B. Continuous loop sensing of high temperature along the bleed ducting
C. Failure of the Precooler temperature sensor
D. Opening of the Overpressure Shutoff Valve
24. The Precooler regulates downstream bleed air temperature to approximately what
target under normal conditions?
A. $120\,^\circ\text{C}$
B. $200\,^\circ\text{C}$
C. $280\,^\circ\text{C}$
D. $350\,^\circ\text{C}$
Section 2: Packs & Temperature Control Logic
25. What happens to the Pack Valves during an engine start sequence in flight?
A. Both remain open at normal flow
B. They close automatically to provide maximum air for engine start
C. They switch to High Flow mode
D. Emergency Ram Air opens automatically
26. What component regulates water drainage from the water separator/collector back into
the ram air duct?
A. High-Pressure Bleed Valve
B. Water Injector / Spray Nozzle
C. Gasper Fan
D. Recirculation Shutoff Valve
27. What is the primary function of the Condenser in the air conditioning pack?
A. To heat ram air before it enters the heat exchanger
B. To cool the air leaving the compressor stage so moisture condenses out
C. To prevent cabin air from entering the avionics compartment
D. To regulate the ground air conditioning connection
28. If the Temperature Controller loses all cabin temperature selector inputs, how does it
control zone temperature?
A. Shuts down both packs immediately
B. Drives the trim air valves to 100% open
C. Maintains a fixed default supply temperature schedule
D. Opens the emergency ram air valve
Section 3: CPCS & Pressurization Scenarios
29. What happens if the pilot sets the CPCS mode to MANUAL and uses the manual
control switch?
A. Channel A continues to run in the background
B. DC electrical power directly drives the manual motor on the Outflow Valve
C. The AMS overrides manual inputs above $25{,}000\text{ ft}$
D. The DUMP switch functionality is disabled
30. What is the maximum differential pressure ($\Delta P$) permitted under normal
operating schedules at high altitude (above $37{,}000\text{ ft}$)?
A. $7.77\text{ psid}$
B. $8.32\text{ psid}$
C. $8.80\text{ psid}$
D. $9.10\text{ psid}$
31. How does the CPCS prevent cabin pressure altitude from exceeding structural limits if
both auto channels fail?
A. Mechanical safety relief valves open at maximum differential pressure
B. The APU starts automatically to add pressure
C. The Emergency Ram Air valve opens
D. The Gasper shutoff valve closes
32. What causes the Cabin Altitude logic to enter "Aborted Takeoff Mode"?
A. Parking brake set while engines are running
B. Throttle retarded to idle before takeoff velocity/liftoff while cabin is pre-pressurized
C. Engine failure on takeoff roll
D. Rapid loss of bleed pressure below $1{,}000\text{ ft}$
Section 4: Avionics Cooling & Cargo Ventilation
33. How does the Forward Avionics Cooling system behave when the aircraft is in flight
and ambient temperature is very low?
A. Both Fan 1 and Fan 2 run at maximum speed
B. System switches to natural convection / differential pressure driving flow, saving fan wear
C. Heated bleed air is injected directly into the racks
D. Middle Avionics Fan 3 takes over all cooling
34. What is the purpose of the Smoke Evacuation Mode in the avionics ventilation system?
A. Reverses fan direction to push smoke into the cargo bay
B. Closes supply valves and opens the Overboard Exhaust Valve to draw smoke out
C. Directs gasper air into the electronic racks
D. Increases recirculation fan speed to filter smoke through HEPA filters
35. If cargo fire system bottle 1 is discharged into the Forward Cargo Bay, what signals the
cargo fan to stop?
A. Smoke detector / Fire protection system signal to the AMS
B. High temperature sensor in the aft bulkhead
C. CPCS DUMP switch activation
D. Manual toggle on the maintenance panel
36. Where is the Gasper Air Fan physically located?
A. In the nose landing gear bay
B. In the aft equipment bay / air conditioning bay area
C. Inside the cockpit center pedestal
D. In the tailcone next to the APU
Section 5: Distribution & Maintenance Operations
37. Which EICAS message indicates that a HEPA recirculation filter is clogged or
restricted?
A. RECIRC FAN FAIL
B. RECIRC FILTER AIRFLOW / Maintenance status message
C. PACK 1 OVHT
D. RAM AIR OPEN
38. What is the default position of the Check Valves in the cabin recirculation line?
A. Spring-loaded closed (opens with airflow)
B. Motor-driven fully open
C. Solenoid-latched closed
D. Variable position modulated by AMS
39. During a dual pack failure scenario at $18{,}000\text{ ft}$, what provides fresh air to
the cabin?
A. APU compressor automatically
B. Emergency Ram Air Valve opening due to system logic
C. Outflow valve fully open
D. Cargo ventilation fan operating in reverse
40. Why must maintenance personnel inspect duct tie-down straps during structural or
ECS checks?
A. To ensure electrical grounding of the carbon fiber ducts
B. To prevent duct movement, disconnection, or chafing against surrounding aircraft structure
C. To measure duct internal pressure limits
D. To calibrate the trim air valve position sensors
Answer Key
Question
#
Correct Answer
21
A — Right-hand wing-to-body fairing
22
B — Closes it automatically during engine start to prevent backflow
23
B — Continuous loop sensing of high temperature along the bleed ducting
24
B — $200\,^\circ\text{C}$
25
B — They close automatically to provide maximum air for engine start
26
B — Water Injector / Spray Nozzle
27
B — To cool the air leaving the compressor stage so moisture condenses out
28
C — Maintains a fixed default supply temperature schedule
29
B — DC electrical power directly drives the manual motor on the Outflow
Valve
30
B — $8.32\text{ psid}$
31
A — Mechanical safety relief valves open at maximum differential pressure
32
B — Throttle retarded to idle before takeoff velocity/liftoff while cabin is
pre-pressurized
33
B — System switches to natural convection / differential pressure driving
flow, saving fan wear
34
B — Closes supply valves and opens the Overboard Exhaust Valve to draw
smoke out
35
A — Smoke detector / Fire protection system signal to the AMS
36
B — In the aft equipment bay / air conditioning bay area
37
B — RECIRC FILTER AIRFLOW / Maintenance status message
Question
#
Correct Answer
38
A — Spring-loaded closed (opens with airflow)
39
B — Emergency Ram Air Valve opening due to system logic
40
B — To prevent duct movement, disconnection, or chafing against
surrounding aircraft structure
41. How does the AMS controller respond if a bleed air over-temperature condition is
detected in Engine 1 Bleed Line?
A. Automatically opens the Crossbleed Valve and turns on the APU
B. Closes Engine 1 Bleed Valve (EBV) and High-Pressure Bleed Valve (HPBV)
C. Drives the Precooler Fan Air Valve (FAV) fully closed
D. Deploys the Emergency Ram Air Valve
42. Under normal engine start on the ground using crossbleed air, what position must the
Crossbleed Valve (XBLEED) be in?
A. Auto (switches open based on system demand) or forced Open
B. Forced Closed
C. Modulating at 50%
D. High Flow mode
43. What is the role of the Fan Air Valve (FAV) in the precooler system?
A. Regulates fuel flow to the engine fan
B. Controls the amount of cold engine fan bypass air entering the precooler
C. Directly vents hot bleed air overboard
D. Meters supply air to the Gasper distribution system
44. What happens to the APU Bleed Valve if an APU bleed leak is detected by the leak
detection loops?
A. It modulates to lower pressure
B. It automatically closes, and the APU BLEED switch light indicates a leak fault
C. Crossbleed valve opens automatically to compensate
D. The APU automatically performs an emergency shut down after 5 minutes
Section 2: Pack Operations & Zone Temperature Control
45. What component is responsible for mixing cold air from the pack with hot trim air
before distribution to the cabin?
A. Gasper Fan
B. Air Conditioning Mixing Chamber (Manifold)
C. Precooler
D. Condenser
46. If the Flight Deck zone temperature selector is turned to full COLD, how does the AMS
adjust the Flight Deck Trim Air Valve?
A. Opens the Trim Air Valve fully
B. Closes the Trim Air Valve to eliminate hot air addition
C. Drives the Pack Flow Control Valve closed
D. Increases recirculation fan speed to maximum
47. What is the function of the Water Injector inside the air conditioning pack ram air
duct?
A. To wash the HEPA filters during flight
B. To spray collected moisture onto the secondary heat exchanger matrix to increase cooling
efficiency
C. To prevent fuel ice formation on the wing leading edge
D. To humidify the passenger cabin air
48. If both Air Conditioning Packs are turned OFF manually in flight below $25{,}000\text{
ft}$, what message appears on the EICAS?
A. PACK 1(2) OFF and RAM AIR OPEN (if emergency ram air conditions are met)
B. CPCS AUTO FAIL
C. BLEED AIR LEAK
D. FORWARD CARGO FAN
Section 3: CPCS & Safety Mechanisms
49. What secondary safety feature prevents over-pressurization of the fuselage if the CPCS
fails to open the Outflow Valve?
A. Emergency Ram Air Valve
B. Positive Safety Pressure Relief Valves (Mechanical)
C. Overboard Exhaust Valve
D. Cockpit Pressure DUMP Switch
50. During ground operations before engine start, what is the nominal position of the
Outflow Valve (OFV)?
A. Fully closed to hold ground pressure
B. Fully open to prevent cabin pressurization on the ground
C. Half-open for pre-cooling
D. Modulating rapidly
51. When the CPCS is operating in 'GRADUAL PRESSURIZATION' mode during
descent, what triggers the final depressurization to ambient pressure?
A. Passing $10{,}000\text{ ft}$ MSL
B. Landing gear touchdown / weight-on-wheels (WOW) signal
C. Flaps set to Full Landing position
D. Shutting down Engine 1
52. What cabin rate of climb limit is automatically maintained by the CPCS during a
normal climb phase?
A. $300\text{ ft/min}$
B. $500\text{ to } 800\text{ ft/min}$
C. $1{,}500\text{ ft/min}$
D. $2{,}500\text{ ft/min}$
Section 4: Equipment Cooling & Smoke Operations
53. Where does the exhaust air from the Middle Avionics Bay discharge during flight when
under pressure differential?
A. Into the Forward Cargo Bay
B. Underfloor area / Outboard towards the outflow valve airflow path
C. Directly into the Flight Deck footwells
D. Back into the engine inlet cowl
54. What happens to the Forward Avionics Cooling System if ambient temperature on the
ground is below $30\,^\circ\text{C}$?
A. Only Fan 1 operates (Fan 2 remains standby/alternating)
B. Both Fan 1 and Fan 2 operate continuously
C. All fans turn off and natural convection is used
D. Emergency Ram Air opens
55. When the CPCS DUMP switch is activated, to what maximum cabin altitude will the
system allow the cabin to climb?
A. $8{,}000\text{ ft}$
B. $10{,}000\text{ ft}$
C. $12{,}400\text{ ft}$ ($\pm 400\text{ ft}$)
D. $15{,}000\text{ ft}$
56. How is cargo compartment temperature controlled in the optional Forward Cargo
Heating system?
A. By modulating a dedicated Trim Air Valve or cycling an electric heater unit based on zone
thermostats
B. By opening the Emergency Ram Air Valve
C. By directing engine exhaust around the cargo liner
D. By cycling the main Pack Flow Control Valve
Section 5: Recirculation & Maintenance Checks
57. What component prevents backflow of cabin air through an inactive Recirculation
Fan?
A. High-Pressure Shutoff Valve
B. Non-Return / Check Valve installed downstream of the fan
C. Outflow Valve
D. Gasper Shutoff Valve
58. What is the main maintenance hazard when servicing or replacing HEPA filters in the
cabin recirculation system?
A. High internal electrical charge
B. Exposure to accumulated biological dust/particulates requiring PPE (gloves and mask)
C. Rapid decompression hazard
D. High-temperature fluid burns
59. If the Cabin Recirculation Fans are turned OFF by selecting the switch to OFF, how
does the AMS adjust fresh air pack flow?
A. Reduces pack flow by 50%
B. Increases pack flow to compensate for the lost recirculated air volume
C. Trips the packs OFF
D. Opens the Overboard Exhaust Valve
60. Which system page on the Multifunction Display (MFD) displays real-time duct
temperatures, valve positions, and pack pressures for maintenance troubleshooting?
A. MFD Fuel Page
B. MFD ECS Synoptic / Maintenance Page
C. MFD Hydraulics Page
D. MFD Flight Control Page
Here are 20 more multiple-choice practice questions (Questions 41–60) focusing on advanced
system logic, abnormal procedures, and maintenance considerations for the Embraer 170 ECS.
E170 ECS Multiple-Choice Quiz (Part 3)
Section 1: Pneumatic Control & Crossbleed Logic
41. How does the AMS controller respond if a bleed air over-temperature condition is
detected in Engine 1 Bleed Line?
A. Automatically opens the Crossbleed Valve and turns on the APU
B. Closes Engine 1 Bleed Valve (EBV) and High-Pressure Bleed Valve (HPBV)
C. Drives the Precooler Fan Air Valve (FAV) fully closed
D. Deploys the Emergency Ram Air Valve
42. Under normal engine start on the ground using crossbleed air, what position must the
Crossbleed Valve (XBLEED) be in?
A. Auto (switches open based on system demand) or forced Open
B. Forced Closed
C. Modulating at 50%
D. High Flow mode
43. What is the role of the Fan Air Valve (FAV) in the precooler system?
A. Regulates fuel flow to the engine fan
B. Controls the amount of cold engine fan bypass air entering the precooler
C. Directly vents hot bleed air overboard
D. Meters supply air to the Gasper distribution system
44. What happens to the APU Bleed Valve if an APU bleed leak is detected by the leak
detection loops?
A. It modulates to lower pressure
B. It automatically closes, and the APU BLEED switch light indicates a leak fault
C. Crossbleed valve opens automatically to compensate
D. The APU automatically performs an emergency shut down after 5 minutes
Section 2: Pack Operations & Zone Temperature Control
45. What component is responsible for mixing cold air from the pack with hot trim air
before distribution to the cabin?
A. Gasper Fan
B. Air Conditioning Mixing Chamber (Manifold)
C. Precooler
D. Condenser
46. If the Flight Deck zone temperature selector is turned to full COLD, how does the AMS
adjust the Flight Deck Trim Air Valve?
A. Opens the Trim Air Valve fully
B. Closes the Trim Air Valve to eliminate hot air addition
C. Drives the Pack Flow Control Valve closed
D. Increases recirculation fan speed to maximum
47. What is the function of the Water Injector inside the air conditioning pack ram air
duct?
A. To wash the HEPA filters during flight
B. To spray collected moisture onto the secondary heat exchanger matrix to increase cooling
efficiency
C. To prevent fuel ice formation on the wing leading edge
D. To humidify the passenger cabin air
48. If both Air Conditioning Packs are turned OFF manually in flight below $25{,}000\text{
ft}$, what message appears on the EICAS?
A. PACK 1(2) OFF and RAM AIR OPEN (if emergency ram air conditions are met)
B. CPCS AUTO FAIL
C. BLEED AIR LEAK
D. FORWARD CARGO FAN
Section 3: CPCS & Safety Mechanisms
49. What secondary safety feature prevents over-pressurization of the fuselage if the CPCS
fails to open the Outflow Valve?
A. Emergency Ram Air Valve
B. Positive Safety Pressure Relief Valves (Mechanical)
C. Overboard Exhaust Valve
D. Cockpit Pressure DUMP Switch
50. During ground operations before engine start, what is the nominal position of the
Outflow Valve (OFV)?
A. Fully closed to hold ground pressure
B. Fully open to prevent cabin pressurization on the ground
C. Half-open for pre-cooling
D. Modulating rapidly
51. When the CPCS is operating in 'GRADUAL PRESSURIZATION' mode during
descent, what triggers the final depressurization to ambient pressure?
A. Passing $10{,}000\text{ ft}$ MSL
B. Landing gear touchdown / weight-on-wheels (WOW) signal
C. Flaps set to Full Landing position
D. Shutting down Engine 1
52. What cabin rate of climb limit is automatically maintained by the CPCS during a
normal climb phase?
A. $300\text{ ft/min}$
B. $500\text{ to } 800\text{ ft/min}$
C. $1{,}500\text{ ft/min}$
D. $2{,}500\text{ ft/min}$
Section 4: Equipment Cooling & Smoke Operations
53. Where does the exhaust air from the Middle Avionics Bay discharge during flight when
under pressure differential?
A. Into the Forward Cargo Bay
B. Underfloor area / Outboard towards the outflow valve airflow path
C. Directly into the Flight Deck footwells
D. Back into the engine inlet cowl
54. What happens to the Forward Avionics Cooling System if ambient temperature on the
ground is below $30\,^\circ\text{C}$?
A. Only Fan 1 operates (Fan 2 remains standby/alternating)
B. Both Fan 1 and Fan 2 operate continuously
C. All fans turn off and natural convection is used
D. Emergency Ram Air opens
55. When the CPCS DUMP switch is activated, to what maximum cabin altitude will the
system allow the cabin to climb?
A. $8{,}000\text{ ft}$
B. $10{,}000\text{ ft}$
C. $12{,}400\text{ ft}$ ($\pm 400\text{ ft}$)
D. $15{,}000\text{ ft}$
56. How is cargo compartment temperature controlled in the optional Forward Cargo
Heating system?
A. By modulating a dedicated Trim Air Valve or cycling an electric heater unit based on zone
thermostats
B. By opening the Emergency Ram Air Valve
C. By directing engine exhaust around the cargo liner
D. By cycling the main Pack Flow Control Valve
Section 5: Recirculation & Maintenance Checks
57. What component prevents backflow of cabin air through an inactive Recirculation
Fan?
A. High-Pressure Shutoff Valve
B. Non-Return / Check Valve installed downstream of the fan
C. Outflow Valve
D. Gasper Shutoff Valve
58. What is the main maintenance hazard when servicing or replacing HEPA filters in the
cabin recirculation system?
A. High internal electrical charge
B. Exposure to accumulated biological dust/particulates requiring PPE (gloves and mask)
C. Rapid decompression hazard
D. High-temperature fluid burns
59. If the Cabin Recirculation Fans are turned OFF by selecting the switch to OFF, how
does the AMS adjust fresh air pack flow?
A. Reduces pack flow by 50%
B. Increases pack flow to compensate for the lost recirculated air volume
C. Trips the packs OFF
D. Opens the Overboard Exhaust Valve
60. Which system page on the Multifunction Display (MFD) displays real-time duct
temperatures, valve positions, and pack pressures for maintenance troubleshooting?
A. MFD Fuel Page
B. MFD ECS Synoptic / Maintenance Page
C. MFD Hydraulics Page
D. MFD Flight Control Page
Answer Key
Question
#
Correct Answer
41
B — Closes Engine 1 Bleed Valve (EBV) and High-Pressure Bleed Valve
(HPBV)
42
A — Auto (switches open based on system demand) or forced Open
43
B — Controls the amount of cold engine fan bypass air entering the
precooler
44
B — It automatically closes, and the APU BLEED switch light indicates a
leak fault
45
B — Air Conditioning Mixing Chamber (Manifold)
46
B — Closes the Trim Air Valve to eliminate hot air addition
47
B — To spray collected moisture onto the secondary heat exchanger matrix
to increase cooling efficiency
48
A — PACK 1(2) OFF and RAM AIR OPEN (if emergency ram air
conditions are met)
49
B — Positive Safety Pressure Relief Valves (Mechanical)
50
B — Fully open to prevent cabin pressurization on the ground
51
B — Landing gear touchdown / weight-on-wheels (WOW) signal
52
B — $500\text{ to } 800\text{ ft/min}$
Question
#
Correct Answer
53
B — Underfloor area / Outboard towards the outflow valve airflow path
54
A — Only Fan 1 operates (Fan 2 remains standby/alternating)
55
C — $12{,}400\text{ ft}$ ($\pm 400\text{ ft}$)
56
A — By modulating a dedicated Trim Air Valve or cycling an electric heater
unit based on zone thermostats
57
B — Non-Return / Check Valve installed downstream of the fan
58
B — Exposure to accumulated biological dust/particulates requiring PPE
(gloves and mask)
59
B — Increases pack flow to compensate for the lost recirculated air volume
60
B — MFD ECS Synoptic / Maintenance Page
E170 ECS Multiple-Choice Quiz (Part 3)
Section 1: Pneumatic Control & Crossbleed Logic
41. How does the AMS controller respond if a bleed air over-temperature condition is
detected in Engine 1 Bleed Line?
A. Automatically opens the Crossbleed Valve and turns on the APU
B. Closes Engine 1 Bleed Valve (EBV) and High-Pressure Bleed Valve (HPBV)
C. Drives the Precooler Fan Air Valve (FAV) fully closed
D. Deploys the Emergency Ram Air Valve
42. Under normal engine start on the ground using crossbleed air, what position must the
Crossbleed Valve (XBLEED) be in?
A. Auto (switches open based on system demand) or forced Open
B. Forced Closed
C. Modulating at 50%
D. High Flow mode
43. What is the role of the Fan Air Valve (FAV) in the precooler system?
A. Regulates fuel flow to the engine fan
B. Controls the amount of cold engine fan bypass air entering the precooler
C. Directly vents hot bleed air overboard
D. Meters supply air to the Gasper distribution system
44. What happens to the APU Bleed Valve if an APU bleed leak is detected by the leak
detection loops?
A. It modulates to lower pressure
B. It automatically closes, and the APU BLEED switch light indicates a leak fault
C. Crossbleed valve opens automatically to compensate
D. The APU automatically performs an emergency shut down after 5 minutes
Section 2: Pack Operations & Zone Temperature Control
45. What component is responsible for mixing cold air from the pack with hot trim air
before distribution to the cabin?
A. Gasper Fan
B. Air Conditioning Mixing Chamber (Manifold)
C. Precooler
D. Condenser
46. If the Flight Deck zone temperature selector is turned to full COLD, how does the AMS
adjust the Flight Deck Trim Air Valve?
A. Opens the Trim Air Valve fully
B. Closes the Trim Air Valve to eliminate hot air addition
C. Drives the Pack Flow Control Valve closed
D. Increases recirculation fan speed to maximum
47. What is the function of the Water Injector inside the air conditioning pack ram air
duct?
A. To wash the HEPA filters during flight
B. To spray collected moisture onto the secondary heat exchanger matrix to increase cooling
efficiency
C. To prevent fuel ice formation on the wing leading edge
D. To humidify the passenger cabin air
48. If both Air Conditioning Packs are turned OFF manually in flight below $25{,}000\text{
ft}$, what message appears on the EICAS?
A. PACK 1(2) OFF and RAM AIR OPEN (if emergency ram air conditions are met)
B. CPCS AUTO FAIL
C. BLEED AIR LEAK
D. FORWARD CARGO FAN
Section 3: CPCS & Safety Mechanisms
49. What secondary safety feature prevents over-pressurization of the fuselage if the CPCS
fails to open the Outflow Valve?
A. Emergency Ram Air Valve
B. Positive Safety Pressure Relief Valves (Mechanical)
C. Overboard Exhaust Valve
D. Cockpit Pressure DUMP Switch
50. During ground operations before engine start, what is the nominal position of the
Outflow Valve (OFV)?
A. Fully closed to hold ground pressure
B. Fully open to prevent cabin pressurization on the ground
C. Half-open for pre-cooling
D. Modulating rapidly
51. When the CPCS is operating in 'GRADUAL PRESSURIZATION' mode during
descent, what triggers the final depressurization to ambient pressure?
A. Passing $10{,}000\text{ ft}$ MSL
B. Landing gear touchdown / weight-on-wheels (WOW) signal
C. Flaps set to Full Landing position
D. Shutting down Engine 1
52. What cabin rate of climb limit is automatically maintained by the CPCS during a
normal climb phase?
A. $300\text{ ft/min}$
B. $500\text{ to } 800\text{ ft/min}$
C. $1{,}500\text{ ft/min}$
D. $2{,}500\text{ ft/min}$
Section 4: Equipment Cooling & Smoke Operations
53. Where does the exhaust air from the Middle Avionics Bay discharge during flight when
under pressure differential?
A. Into the Forward Cargo Bay
B. Underfloor area / Outboard towards the outflow valve airflow path
C. Directly into the Flight Deck footwells
D. Back into the engine inlet cowl
54. What happens to the Forward Avionics Cooling System if ambient temperature on the
ground is below $30\,^\circ\text{C}$?
A. Only Fan 1 operates (Fan 2 remains standby/alternating)
B. Both Fan 1 and Fan 2 operate continuously
C. All fans turn off and natural convection is used
D. Emergency Ram Air opens
55. When the CPCS DUMP switch is activated, to what maximum cabin altitude will the
system allow the cabin to climb?
A. $8{,}000\text{ ft}$
B. $10{,}000\text{ ft}$
C. $12{,}400\text{ ft}$ ($\pm 400\text{ ft}$)
D. $15{,}000\text{ ft}$
56. How is cargo compartment temperature controlled in the optional Forward Cargo
Heating system?
A. By modulating a dedicated Trim Air Valve or cycling an electric heater unit based on zone
thermostats
B. By opening the Emergency Ram Air Valve
C. By directing engine exhaust around the cargo liner
D. By cycling the main Pack Flow Control Valve
Section 5: Recirculation & Maintenance Checks
57. What component prevents backflow of cabin air through an inactive Recirculation
Fan?
A. High-Pressure Shutoff Valve
B. Non-Return / Check Valve installed downstream of the fan
C. Outflow Valve
D. Gasper Shutoff Valve
58. What is the main maintenance hazard when servicing or replacing HEPA filters in the
cabin recirculation system?
A. High internal electrical charge
B. Exposure to accumulated biological dust/particulates requiring PPE (gloves and mask)
C. Rapid decompression hazard
D. High-temperature fluid burns
59. If the Cabin Recirculation Fans are turned OFF by selecting the switch to OFF, how
does the AMS adjust fresh air pack flow?
A. Reduces pack flow by 50%
B. Increases pack flow to compensate for the lost recirculated air volume
C. Trips the packs OFF
D. Opens the Overboard Exhaust Valve
60. Which system page on the Multifunction Display (MFD) displays real-time duct
temperatures, valve positions, and pack pressures for maintenance troubleshooting?
A. MFD Fuel Page
B. MFD ECS Synoptic / Maintenance Page
C. MFD Hydraulics Page
D. MFD Flight Control Page
Here are 20 more multiple-choice practice questions (Questions 41–60) focusing on advanced
system logic, abnormal procedures, and maintenance considerations for the Embraer 170 ECS.
E170 ECS Multiple-Choice Quiz (Part 3)
Section 1: Pneumatic Control & Crossbleed Logic
41. How does the AMS controller respond if a bleed air over-temperature condition is
detected in Engine 1 Bleed Line?
A. Automatically opens the Crossbleed Valve and turns on the APU
B. Closes Engine 1 Bleed Valve (EBV) and High-Pressure Bleed Valve (HPBV)
C. Drives the Precooler Fan Air Valve (FAV) fully closed
D. Deploys the Emergency Ram Air Valve
42. Under normal engine start on the ground using crossbleed air, what position must the
Crossbleed Valve (XBLEED) be in?
A. Auto (switches open based on system demand) or forced Open
B. Forced Closed
C. Modulating at 50%
D. High Flow mode
43. What is the role of the Fan Air Valve (FAV) in the precooler system?
A. Regulates fuel flow to the engine fan
B. Controls the amount of cold engine fan bypass air entering the precooler
C. Directly vents hot bleed air overboard
D. Meters supply air to the Gasper distribution system
44. What happens to the APU Bleed Valve if an APU bleed leak is detected by the leak
detection loops?
A. It modulates to lower pressure
B. It automatically closes, and the APU BLEED switch light indicates a leak fault
C. Crossbleed valve opens automatically to compensate
D. The APU automatically performs an emergency shut down after 5 minutes
Section 2: Pack Operations & Zone Temperature Control
45. What component is responsible for mixing cold air from the pack with hot trim air
before distribution to the cabin?
A. Gasper Fan
B. Air Conditioning Mixing Chamber (Manifold)
C. Precooler
D. Condenser
46. If the Flight Deck zone temperature selector is turned to full COLD, how does the AMS
adjust the Flight Deck Trim Air Valve?
A. Opens the Trim Air Valve fully
B. Closes the Trim Air Valve to eliminate hot air addition
C. Drives the Pack Flow Control Valve closed
D. Increases recirculation fan speed to maximum
47. What is the function of the Water Injector inside the air conditioning pack ram air
duct?
A. To wash the HEPA filters during flight
B. To spray collected moisture onto the secondary heat exchanger matrix to increase cooling
efficiency
C. To prevent fuel ice formation on the wing leading edge
D. To humidify the passenger cabin air
48. If both Air Conditioning Packs are turned OFF manually in flight below $25{,}000\text{
ft}$, what message appears on the EICAS?
A. PACK 1(2) OFF and RAM AIR OPEN (if emergency ram air conditions are met)
B. CPCS AUTO FAIL
C. BLEED AIR LEAK
D. FORWARD CARGO FAN
Section 3: CPCS & Safety Mechanisms
49. What secondary safety feature prevents over-pressurization of the fuselage if the CPCS
fails to open the Outflow Valve?
A. Emergency Ram Air Valve
B. Positive Safety Pressure Relief Valves (Mechanical)
C. Overboard Exhaust Valve
D. Cockpit Pressure DUMP Switch
50. During ground operations before engine start, what is the nominal position of the
Outflow Valve (OFV)?
A. Fully closed to hold ground pressure
B. Fully open to prevent cabin pressurization on the ground
C. Half-open for pre-cooling
D. Modulating rapidly
51. When the CPCS is operating in 'GRADUAL PRESSURIZATION' mode during
descent, what triggers the final depressurization to ambient pressure?
A. Passing $10{,}000\text{ ft}$ MSL
B. Landing gear touchdown / weight-on-wheels (WOW) signal
C. Flaps set to Full Landing position
D. Shutting down Engine 1
52. What cabin rate of climb limit is automatically maintained by the CPCS during a
normal climb phase?
A. $300\text{ ft/min}$
B. $500\text{ to } 800\text{ ft/min}$
C. $1{,}500\text{ ft/min}$
D. $2{,}500\text{ ft/min}$
Section 4: Equipment Cooling & Smoke Operations
53. Where does the exhaust air from the Middle Avionics Bay discharge during flight when
under pressure differential?
A. Into the Forward Cargo Bay
B. Underfloor area / Outboard towards the outflow valve airflow path
C. Directly into the Flight Deck footwells
D. Back into the engine inlet cowl
54. What happens to the Forward Avionics Cooling System if ambient temperature on the
ground is below $30\,^\circ\text{C}$?
A. Only Fan 1 operates (Fan 2 remains standby/alternating)
B. Both Fan 1 and Fan 2 operate continuously
C. All fans turn off and natural convection is used
D. Emergency Ram Air opens
55. When the CPCS DUMP switch is activated, to what maximum cabin altitude will the
system allow the cabin to climb?
A. $8{,}000\text{ ft}$
B. $10{,}000\text{ ft}$
C. $12{,}400\text{ ft}$ ($\pm 400\text{ ft}$)
D. $15{,}000\text{ ft}$
56. How is cargo compartment temperature controlled in the optional Forward Cargo
Heating system?
A. By modulating a dedicated Trim Air Valve or cycling an electric heater unit based on zone
thermostats
B. By opening the Emergency Ram Air Valve
C. By directing engine exhaust around the cargo liner
D. By cycling the main Pack Flow Control Valve
Section 5: Recirculation & Maintenance Checks
57. What component prevents backflow of cabin air through an inactive Recirculation
Fan?
A. High-Pressure Shutoff Valve
B. Non-Return / Check Valve installed downstream of the fan
C. Outflow Valve
D. Gasper Shutoff Valve
58. What is the main maintenance hazard when servicing or replacing HEPA filters in the
cabin recirculation system?
A. High internal electrical charge
B. Exposure to accumulated biological dust/particulates requiring PPE (gloves and mask)
C. Rapid decompression hazard
D. High-temperature fluid burns
59. If the Cabin Recirculation Fans are turned OFF by selecting the switch to OFF, how
does the AMS adjust fresh air pack flow?
A. Reduces pack flow by 50%
B. Increases pack flow to compensate for the lost recirculated air volume
C. Trips the packs OFF
D. Opens the Overboard Exhaust Valve
60. Which system page on the Multifunction Display (MFD) displays real-time duct
temperatures, valve positions, and pack pressures for maintenance troubleshooting?
A. MFD Fuel Page
B. MFD ECS Synoptic / Maintenance Page
C. MFD Hydraulics Page
D. MFD Flight Control Page
Answer Key
Question
#
Correct Answer
41
B — Closes Engine 1 Bleed Valve (EBV) and High-Pressure Bleed Valve
(HPBV)
42
A — Auto (switches open based on system demand) or forced Open
43
B — Controls the amount of cold engine fan bypass air entering the
precooler
44
B — It automatically closes, and the APU BLEED switch light indicates a
leak fault
45
B — Air Conditioning Mixing Chamber (Manifold)
46
B — Closes the Trim Air Valve to eliminate hot air addition
Question
#
Correct Answer
47
B — To spray collected moisture onto the secondary heat exchanger matrix
to increase cooling efficiency
48
A — PACK 1(2) OFF and RAM AIR OPEN (if emergency ram air
conditions are met)
49
B — Positive Safety Pressure Relief Valves (Mechanical)
50
B — Fully open to prevent cabin pressurization on the ground
51
B — Landing gear touchdown / weight-on-wheels (WOW) signal
52
B — $500\text{ to } 800\text{ ft/min}$
53
B — Underfloor area / Outboard towards the outflow valve airflow path
54
A — Only Fan 1 operates (Fan 2 remains standby/alternating)
55
C — $12{,}400\text{ ft}$ ($\pm 400\text{ ft}$)
56
A — By modulating a dedicated Trim Air Valve or cycling an electric heater
unit based on zone thermostats
57
B — Non-Return / Check Valve installed downstream of the fan
58
B — Exposure to accumulated biological dust/particulates requiring PPE
(gloves and mask)
59
B — Increases pack flow to compensate for the lost recirculated air volume
60
B — MFD ECS Synoptic / Maintenance Page
Part 2: Q&A
1. During normal operation, each ECS cooling pack is
controlled to provide:
A. 40% of the total fresh airflow reference
B. 50% of the total fresh airflow reference
C. 67% of the total fresh airflow reference
D. 75% of the total fresh airflow reference
Answer: B
Each cooling pack normally supplies half of the total fresh airflow.
2. During single-engine bleed with dual-pack operation, the
AMS reduces total fresh airflow to:
A. 50%
B. 67%
C. 75%
D. 100%
Answer: C
During single-engine bleed and dual-pack operation, the AMS limits total fresh airflow to 75%
of the reference.
3. Under which condition will the opposite-side air
conditioning pack automatically shut down during singleengine bleed operation?
A. Wing anti-ice selected ON
B. Slat anti-ice selected ON
C. Engine anti-ice selected ON
D. Crossbleed valve OPEN
Answer: B
The opposite pack is turned OFF when slat anti-ice is required during single-engine bleed
operation.
4. Which parameters are used by the AMS to calculate pack
airflow?
A. Differential pressure only
B. Differential pressure and manifold pressure
C. Differential pressure, manifold pressure and pack inlet temperature
D. Pack outlet temperature and manifold pressure
Answer: C
The AMS calculates airflow using:
Venturi differential pressure
Bleed manifold pressure
Pack inlet temperature
5. What is the primary purpose of the flow sensing venturi?
A. Reduce bleed air temperature
B. Measure bleed air pressure
C. Calculate airflow into the ECS
D. Control pack bypass operation
Answer: C
The venturi creates a pressure differential used to calculate airflow.
6. Which component directly receives the AMS torquemotor command to regulate pack airflow?
A. Pack bypass valve
B. Flow control valve
C. Pack shutoff valve
D. Precooler valve
Answer: B
The AMS sends a torque-motor current command to the flow control valve.
7. Which statement correctly describes the recirculation
airflow?
A. 60% fresh air and 40% recirculated air
B. 52% fresh air and 48% recirculated air
C. 48% fresh air and 52% recirculated air
D. 75% fresh air and 25% recirculated air
Answer: B
Approximately 52% fresh air and 48% recirculated air enter the cockpit and cabin.
8. Both recirculation fans will be commanded OFF when:
A. One ECS pack fails.
B. The RECIRC switch is OFF.
C. Smoke is detected in the recirculation bay.
D. Both B and C.
Answer: D
Both fans are commanded OFF if the RECIRC switch is OFF or smoke is detected in the
recirculation bay.
9. Which statement is true regarding single-pack operation
in flight?
A. Right pack alone operates both recirculation fans.
B. Left pack alone operates both recirculation fans.
C. Both fans are OFF whenever only one pack operates.
D. Only the left fan remains ON regardless of the operating pack.
Answer: B
With only the left pack operating in flight, both recirculation fans remain ON. With only the
right pack, the left fan is OFF.
10. The ozone converter is installed:
A. Downstream of the cooling pack.
B. Upstream of the flow sensing venturi.
C. Downstream of the pack bypass valve.
D. Inside the mixing manifold.
Answer: B
The ozone converter is installed upstream of the flow sensing venturi.
11. The ozone converter reduces ozone concentration by:
A. Filtration.
B. Condensation.
C. Catalytic conversion of ozone into oxygen.
D. Mixing with recirculated air.
Answer: C
The catalytic material converts ozone molecules into oxygen molecules.
12. Which sensor provides the AMS with the airflow
measurement signal?
A. Pack temperature sensor
B. Bleed pressure switch
C. Venturi differential pressure sensor
D. Ambient pressure sensor
Answer: C
The venturi differential pressure sensor provides a 0–10 VDC signal for airflow calculation.
13. A single ECS pack is capable of maintaining adequate
pressurization and temperature control up to:
A. 25,000 ft
B. 31,000 ft
C. 35,000 ft
D. Maximum certified altitude
Answer: B
A single pack can maintain adequate pressurization and temperature control up to 31,000 ft.
14. Which component removes moisture from the
conditioned air inside the cooling pack?
A. Reheater
B. Water collector
C. Air cycle machine
D. Ozone converter
Answer: B
The water collector removes condensed moisture from the pack airflow.
15. The Air Cycle Machine produces cooling primarily by:
A. Refrigerant compression.
B. Expansion through cooling turbines.
C. Vapor compression.
D. Electric refrigeration.
Answer: B
Cooling is produced by expansion through the ACM turbines.
Excellent. This is exactly the style I recommend for your exam preparation. We'll build a
comprehensive ATA 21 GenFam Level 2/3 question bank that covers every system, logic
sequence, protection feature, and operational mode in the manual—not just definitions. I'll
continue with questions 16–30 in the same style.
16. Which component provides the AMS with the
differential pressure used to calculate pack airflow?
A. Pack inlet temperature sensor
B. Differential pressure sensor mounted on the venturi duct
C. Bleed manifold pressure sensor
D. Pack outlet pressure transducer
Answer: B
The differential pressure sensor mounted on the venturi duct measures the pressure drop across
the venturi, allowing the AMS to calculate pack airflow.
17. The venturi differential pressure sensor outputs:
A. 0–5 VAC
B. 4–20 mA
C. 0–10 VDC
D. ARINC 429 digital data
Answer: C
The sensor provides a 0 to 10 VDC signal to the AMS controller.
18. The flow control valve is located:
A. Downstream of the cooling pack.
B. Upstream of the cooling pack.
C. Downstream of the mixing manifold.
D. Between the ACM and condenser.
Answer: B
The pack flow control valve is installed upstream of each ECS pack.
19. Which type of valve is incorporated in the pack flow
control valve?
A. Ball valve
B. Butterfly valve
C. Gate valve
D. Spool valve
Answer: B
The flow control valve is a pneumatically actuated butterfly valve controlled by a torque motor.
20. What is the purpose of the locking screw installed on the
flow control valve actuator?
A. Adjust pack airflow.
B. Lock the valve in the OPEN position.
C. Lock the valve in the CLOSED position.
D. Calibrate the torque motor.
Answer: C
The locking screw can mechanically lock the valve closed for maintenance.
21. During normal operation, Engine 1 normally supplies
bleed air to:
A. Both packs.
B. Pack 2 only.
C. Pack 1 only.
D. Either pack depending on temperature.
Answer: C
Engine 1 normally supplies Pack 1, while Engine 2 supplies Pack 2.
22. Which statement regarding single-pack capability is
correct?
A. A single pack provides full airflow to maximum altitude.
B. A single pack maintains adequate pressurization and temperature control up to 31,000 ft.
C. Single-pack operation is prohibited above FL250.
D. A single pack supplies only the cockpit.
Answer: B
A single ECS pack is capable of maintaining adequate cabin pressurization and temperature
control up to 31,000 ft.
23. The primary function of the ozone converter is to:
A. Remove moisture from bleed air.
B. Reduce carbon dioxide concentration.
C. Convert ozone into oxygen.
D. Remove dust particles.
Answer: C
The ozone converter uses catalytic material to convert ozone molecules into oxygen.
24. The ozone converter is installed:
A. Upstream of the flow sensing venturi.
B. Downstream of the cooling pack.
C. Inside the ACM.
D. Downstream of the mixing manifold.
Answer: A
The ozone converter is located upstream of the flow sensing venturi.
25. Which statement best describes the Air Cycle Machine?
A. It uses refrigerant gas and a compressor.
B. It is an electrically driven refrigeration unit.
C. It uses air as the refrigerant and cooling turbines.
D. It contains hydraulic cooling pumps.
Answer: C
The ACM is an air-cycle refrigeration system that uses air as the refrigerant.
26. Which ACM component removes moisture from the
conditioned air?
A. Condenser/Reheater
B. Water Collector
C. Fan Rotor
D. Compressor Rotor
Answer: B
The water collector removes condensed moisture before conditioned air enters the cabin.
27. The Air Cycle Machine rotating assembly is supported
by:
A. Roller bearings lubricated by engine oil.
B. Ball bearings lubricated by grease.
C. Hydrodynamic foil-type bearings requiring no scheduled maintenance.
D. Magnetic bearings.
Answer: C
The ACM uses hydrodynamic foil bearings that require no scheduled maintenance.
28. Which component of the ACM is driven by the turbine
rotors?
A. Outflow valve.
B. Compressor rotor and cooling fan.
C. Water collector.
D. Pack bypass valve.
Answer: B
The turbine rotors drive both the compressor rotor and the cooling fan rotor.
29. Approximately how often is the cabin air completely
exchanged during normal operation?
A. Every 30–45 seconds.
B. Every 2.5–3.5 minutes.
C. Every 10 minutes.
D. Every 15 minutes.
Answer: B
Cabin air is exchanged approximately every 2.5–3.5 minutes (18–25 times per hour).
30. During normal operation, the conditioned air supplied to
the cabin is mixed with:
A. Ram air.
B. Hydraulic cooling air.
C. Filtered recirculated air.
D. Ambient fuselage air.
Answer: C
The conditioned pack air is mixed with an equal quantity of filtered recirculated air before
distribution.
Great. We'll continue in the same Embraer GenFam Level 3 style. The next section begins
covering the Cooling Pack (Air Cycle Machine) in more depth.
ATA 21 – Air Conditioning
Questions 31–45 (Cooling Pack & Air Cycle Machine)
31. The primary function of the Air Cycle Machine (ACM) is to:
A. Increase bleed air pressure before distribution.
B. Cool and dehumidify bleed air supplied to the cockpit and cabin.
C. Regulate cabin differential pressure.
D. Control the recirculation airflow.
Answer: B
The ACM is the refrigeration unit within the cooling pack that cools and dehumidifies bleed air
before it enters the cabin distribution system.
32. Which component is NOT part of the cooling pack?
A. Dual heat exchanger
B. Air cycle machine
C. Water collector
D. Outflow valve
Answer: D
The outflow valve belongs to the pressurization system, not the cooling pack. The cooling pack
consists of the dual heat exchanger, ACM, condenser/reheater, water collector, valves and
sensors.
33. Excess heat from the cooling pack is removed by:
A. Cabin recirculated air.
B. Hydraulic fluid.
C. Outside ram air flowing through the heat exchangers.
D. Electric cooling fans.
Answer: C
The dual heat exchangers use outside ram air to remove heat from the bleed air.
34. Which statement best describes the refrigeration cycle used by the ECS
pack?
A. Vapour-compression refrigeration using refrigerant.
B. Air-cycle refrigeration using bleed air.
C. Liquid cooling using glycol.
D. Refrigeration using hydraulic oil.
Answer: B
The ECS pack is an air-cycle refrigeration system that uses compressed air rather than
refrigerant.
35. The Air Cycle Machine compressor is driven by:
A. An electric motor.
B. The engine accessory gearbox.
C. The turbine rotors through a common shaft.
D. Hydraulic pressure.
Answer: C
The turbine rotors drive the compressor rotor through the common rotating assembly.
36. Which ACM component provides the cooling energy used to condition the
bleed air?
A. Compressor
B. Cooling turbines
C. Water collector
D. Condenser
Answer: B
Cooling is produced by expansion through the cooling turbines.
37. The ACM rotating assembly consists of:
A. Independent compressor and turbine shafts.
B. Four rotors connected into a single rotating assembly.
C. Two electric motors driving two turbines.
D. Three gear-driven shafts.
Answer: B
The fan, compressor and two turbine rotors rotate as one assembly locked together by a tie rod.
38. Which bearing type supports the ACM rotating assembly?
A. Ball bearings
B. Roller bearings
C. Hydrodynamic foil bearings
D. Needle bearings
Answer: C
The ACM uses hydrodynamic foil-type journal and thrust bearings.
39. The primary advantage of the ACM foil bearings is that they:
A. Require engine oil lubrication.
B. Require periodic grease servicing.
C. Require no scheduled maintenance.
D. Operate only during cruise.
Answer: C
The hydrodynamic foil bearings require no scheduled maintenance.
40. The tie rod installed through the ACM rotating assembly serves to:
A. Balance the compressor.
B. Hold the shaft and rotors together axially.
C. Drive the cooling fan independently.
D. Increase compressor speed.
Answer: B
The tie rod holds all rotor components together under high preload, allowing them to operate as
one shaft.
41. The pack bypass valve primarily controls:
A. Cabin pressure.
B. Pack temperature.
C. Ram-air flow through the heat exchangers.
D. Engine bleed pressure.
Answer: B
The pack bypass valve modulates pack operation by controlling pack temperature.
42. Which statement regarding ECS packs is correct?
A. Pack 1 cools only the cockpit.
B. Each pack normally conditions half of the aircraft fresh airflow.
C. Pack 2 supplies all cabin zones during cruise.
D. Both packs always operate together.
Answer: B
Each pack normally conditions approximately half of the total fresh airflow.
43. The conditioned air leaving each cooling pack is:
A. Directed directly overboard.
B. Mixed with filtered recirculated air before cabin distribution.
C. Sent directly to the cockpit only.
D. Routed through the outflow valve.
Answer: B
The conditioned air is mixed with filtered recirculated air before entering the distribution ducts.
44. Moisture removed from the pack airflow is collected by the:
A. Condenser only.
B. Water collector.
C. Mixing manifold.
D. Flow control valve.
Answer: B
The water collector removes condensed moisture from the conditioned air.
45. Which statement best describes the relationship between the pack flow
control valve and the pack bypass valve?
A. Both regulate cabin pressurization.
B. The flow control valve regulates airflow into the pack, while the pack bypass valve regulates
pack operating temperature.
C. Both regulate bleed pressure entering the engine.
D. Both are mechanically linked and always move together.
Answer: B
The flow control valve meters the quantity of bleed air entering the pack, while the pack bypass
valve regulates the pack's cooling performance and outlet temperature.
Perfect. We'll continue in the same Embraer GenFam Level 3 style. These questions move into
Cooling Pack Control and Temperature Regulation, which is heavily tested because it
focuses on logic rather than simple component identification.
ATA 21 – Air Conditioning
Questions 46–60 (Cooling Pack Control & Temperature
Regulation)
46. Which valve is directly modulated by the AMS to maintain the commanded
pack airflow?
A. Pack bypass valve
B. Flow control valve
C. Outflow valve
D. Trim air valve
Answer: B
The AMS modulates the pack flow control valve using a torque motor to achieve the desired
pack airflow.
47. The AMS determines the desired position of the flow control valve using:
A. Cabin altitude only
B. Differential pressure, manifold pressure and pack inlet temperature
C. Cabin temperature only
D. Ram-air temperature only
Answer: B
The AMS uses these three parameters to calculate airflow before positioning the valve.
48. Which component provides position feedback of the pack flow control valve?
A. RVDT
B. LVDT
C. Closed-position switch
D. Potentiometer
Answer: C
The flow control valve incorporates a closed-position switch to provide position feedback to the
AMS.
49. If the flow control valve is mechanically locked for maintenance, it is locked
in the:
A. Full OPEN position
B. Half OPEN position
C. CLOSED position
D. Modulating position
Answer: C
The actuator locking screw locks the valve closed.
50. Which statement correctly describes the pack flow control valve actuator?
A. Electrically actuated butterfly valve
B. Pneumatically actuated butterfly valve controlled by a torque motor
C. Hydraulically actuated poppet valve
D. Electrically driven gate valve
Answer: B
The valve is pneumatically actuated and modulated by a torque motor under AMS control.
51. The primary purpose of the condenser/reheater assembly is to:
A. Increase bleed pressure
B. Improve moisture removal efficiency
C. Pressurize the cabin
D. Drive the ACM compressor
Answer: B
The condenser/reheater improves the condensation and separation of moisture before the air
enters the cabin.
52. Which component actually separates condensed water from the conditioned
airflow?
A. ACM compressor
B. Water collector
C. Dual heat exchanger
D. Pack bypass valve
Answer: B
The water collector removes condensed moisture from the airflow.
53. Why is moisture removed from the conditioned air?
A. To increase cabin pressure
B. To prevent icing and improve passenger comfort
C. To reduce bleed pressure
D. To increase ACM speed
Answer: B
Removing moisture prevents excessive humidity, reduces icing within the pack, and improves
cabin comfort.
54. The dual heat exchanger removes heat from bleed air using:
A. Cabin recirculated air
B. Outside ram air
C. Hydraulic fluid
D. Fuel
Answer: B
Ram air flowing through the heat exchanger removes heat from the bleed air.
55. Which statement regarding the Air Cycle Machine compressor is correct?
A. It is electrically driven.
B. It is hydraulically driven.
C. It is driven by the turbine rotors through the common shaft.
D. It is driven directly by engine bleed pressure.
Answer: C
The compressor is mechanically driven by the turbine rotors through the common rotating
assembly.
56. The cooling pack uses which medium as the refrigerant?
A. R134a
B. Ammonia
C. Air
D. Nitrogen
Answer: C
The ECS cooling pack is an air-cycle refrigeration system using air as the refrigerant.
57. Which statement best describes the ACM cooling process?
A. Compression alone cools the air.
B. Expansion through the cooling turbines produces the cooling effect.
C. Condensation provides all of the cooling.
D. Electric refrigeration cools the cabin air.
Answer: B
Cooling occurs when compressed air expands through the ACM turbines.
58. During normal operation, the conditioned air delivered to the cabin is:
A. 100% fresh bleed air.
B. Mixed with approximately an equal quantity of filtered recirculated air.
C. Mixed with outside ram air.
D. Mixed with cargo compartment ventilation air.
Answer: B
Conditioned air is mixed with filtered recirculated air before cabin distribution.
59. The ACM fan primarily assists in:
A. Cooling the heat exchangers by increasing ram-air flow.
B. Driving the compressor.
C. Pressurizing the cabin.
D. Operating the outflow valve.
Answer: A
The ACM fan improves airflow through the heat exchangers, increasing cooling efficiency.
60. Which statement best explains why the ACM requires no scheduled bearing
maintenance?
A. The bearings are permanently grease packed.
B. The bearings are lubricated by engine oil.
C. The ACM uses hydrodynamic foil bearings that operate without conventional lubrication.
D. The bearings are replaced at every C-check.
Answer: C
The ACM uses hydrodynamic foil-type bearings that require no scheduled maintenance.
Perfect. We'll continue in the same Embraer GenFam Level 3 style. These questions move into
Cooling Pack Control and Temperature Regulation, which is heavily tested because it
focuses on logic rather than simple component identification.
ATA 21 – Air Conditioning
Questions 46–60 (Cooling Pack Control & Temperature
Regulation)
46. Which valve is directly modulated by the AMS to maintain the commanded
pack airflow?
A. Pack bypass valve
B. Flow control valve
C. Outflow valve
D. Trim air valve
Answer: B
The AMS modulates the pack flow control valve using a torque motor to achieve the desired
pack airflow.
47. The AMS determines the desired position of the flow control valve using:
A. Cabin altitude only
B. Differential pressure, manifold pressure and pack inlet temperature
C. Cabin temperature only
D. Ram-air temperature only
Answer: B
The AMS uses these three parameters to calculate airflow before positioning the valve.
48. Which component provides position feedback of the pack flow control valve?
A. RVDT
B. LVDT
C. Closed-position switch
D. Potentiometer
Answer: C
The flow control valve incorporates a closed-position switch to provide position feedback to the
AMS.
49. If the flow control valve is mechanically locked for maintenance, it is locked
in the:
A. Full OPEN position
B. Half OPEN position
C. CLOSED position
D. Modulating position
Answer: C
The actuator locking screw locks the valve closed.
50. Which statement correctly describes the pack flow control valve actuator?
A. Electrically actuated butterfly valve
B. Pneumatically actuated butterfly valve controlled by a torque motor
C. Hydraulically actuated poppet valve
D. Electrically driven gate valve
Answer: B
The valve is pneumatically actuated and modulated by a torque motor under AMS control.
51. The primary purpose of the condenser/reheater assembly is to:
A. Increase bleed pressure
B. Improve moisture removal efficiency
C. Pressurize the cabin
D. Drive the ACM compressor
Answer: B
The condenser/reheater improves the condensation and separation of moisture before the air
enters the cabin.
52. Which component actually separates condensed water from the conditioned
airflow?
A. ACM compressor
B. Water collector
C. Dual heat exchanger
D. Pack bypass valve
Answer: B
The water collector removes condensed moisture from the airflow.
53. Why is moisture removed from the conditioned air?
A. To increase cabin pressure
B. To prevent icing and improve passenger comfort
C. To reduce bleed pressure
D. To increase ACM speed
Answer: B
Removing moisture prevents excessive humidity, reduces icing within the pack, and improves
cabin comfort.
54. The dual heat exchanger removes heat from bleed air using:
A. Cabin recirculated air
B. Outside ram air
C. Hydraulic fluid
D. Fuel
Answer: B
Ram air flowing through the heat exchanger removes heat from the bleed air.
55. Which statement regarding the Air Cycle Machine compressor is correct?
A. It is electrically driven.
B. It is hydraulically driven.
C. It is driven by the turbine rotors through the common shaft.
D. It is driven directly by engine bleed pressure.
Answer: C
The compressor is mechanically driven by the turbine rotors through the common rotating
assembly.
56. The cooling pack uses which medium as the refrigerant?
A. R134a
B. Ammonia
C. Air
D. Nitrogen
Answer: C
The ECS cooling pack is an air-cycle refrigeration system using air as the refrigerant.
57. Which statement best describes the ACM cooling process?
A. Compression alone cools the air.
B. Expansion through the cooling turbines produces the cooling effect.
C. Condensation provides all of the cooling.
D. Electric refrigeration cools the cabin air.
Answer: B
Cooling occurs when compressed air expands through the ACM turbines.
58. During normal operation, the conditioned air delivered to the cabin is:
A. 100% fresh bleed air.
B. Mixed with approximately an equal quantity of filtered recirculated air.
C. Mixed with outside ram air.
D. Mixed with cargo compartment ventilation air.
Answer: B
Conditioned air is mixed with filtered recirculated air before cabin distribution.
59. The ACM fan primarily assists in:
A. Cooling the heat exchangers by increasing ram-air flow.
B. Driving the compressor.
C. Pressurizing the cabin.
D. Operating the outflow valve.
Answer: A
The ACM fan improves airflow through the heat exchangers, increasing cooling efficiency.
60. Which statement best explains why the ACM requires no scheduled bearing
maintenance?
A. The bearings are permanently grease packed.
B. The bearings are lubricated by engine oil.
C. The ACM uses hydrodynamic foil bearings that operate without conventional lubrication.
D. The bearings are replaced at every C-check.
Answer: C
Excellent. From this point onward, we're entering what I consider the highest-yield section of
ATA 21 for Embraer GenFam. Most airline technical exams focus heavily on AMS
temperature control logic, trim air, and zone control rather than simple component
identification.
ATA 21 – Air Conditioning
Questions 61–75 (Temperature Control & Trim Air)
61. Which cockpit control allows independent selection of the flight deck
temperature?
A. PACK 1 switch
B. CKPT temperature selector knob
C. RECIRC switch
D. PRESS MODE selector
Answer: B
The CKPT selector allows the crew to select a cockpit temperature between 19°C and 30°C.
62. The passenger cabin temperature selector allows temperature selection
between:
A. 16°C and 26°C
B. 18°C and 28°C
C. 19°C and 30°C
D. 20°C and 32°C
Answer: C
The passenger cabin selector provides a selectable range of 19°C to 30°C.
63. When the cockpit temperature selector is placed to ATTND, cabin
temperature is controlled from the:
A. MCDU
B. Flight Attendant Panel
C. EICAS
D. CPCS Controller
Answer: B
Selecting ATTND transfers cabin zone temperature control to the Flight Attendant Panel.
64. The optional trim air system provides independent temperature control for:
A. Cockpit and avionics bay
B. Cockpit and cargo compartment
C. Forward and aft passenger cabin zones
D. Flight deck and nose compartment
Answer: C
The optional trim air system provides independent temperature control of the forward and aft
passenger cabin zones.
65. The trim air system uses bleed air supplied from:
A. Pack 1
B. Pack 2
C. The APU only
D. Both packs simultaneously
Answer: B
Trim air uses hot bleed air from Pack 2 for zone temperature trimming.
66. The purpose of the trim air system is to:
A. Increase cabin pressurization.
B. Improve temperature control by adding controlled hot bleed air.
C. Increase pack airflow.
D. Cool avionics equipment.
Answer: B
Trim air improves cabin temperature control by introducing controlled hot bleed air into the
mixer.
67. If the aircraft is not equipped with the optional trim air system:
A. Independent forward and aft cabin temperature control is unavailable.
B. Cockpit temperature control is unavailable.
C. Pack operation is inhibited.
D. Recirculation fans remain OFF.
Answer: A
Without trim air, independent control of the forward and aft cabin zones is not available.
68. Which statement best describes trim air operation?
A. It cools conditioned air using ram air.
B. It reheats already conditioned pack air.
C. It bypasses the ACM.
D. It replaces pack cooling during cruise.
Answer: B
Trim air reheats conditioned air to achieve the desired zone temperature.
69. Which component primarily determines the quantity of fresh air entering
each cooling pack?
A. Trim air valve
B. Flow control valve
C. Pack bypass valve
D. Outflow valve
Answer: B
The flow control valve regulates bleed airflow entering each cooling pack.
70. Temperature control within individual passenger zones is achieved by
varying:
A. Ram-air flow through the heat exchangers.
B. Cabin outflow valve position.
C. The amount of hot trim air mixed with conditioned air.
D. Recirculation fan speed.
Answer: C
Zone temperature is controlled by varying the quantity of hot trim air mixed with conditioned air.
71. Which statement regarding trim air is correct?
A. It supplies cooled air directly from the ACM.
B. It uses hot bleed air to fine-tune cabin temperature.
C. It replaces the cooling pack during single-pack operation.
D. It is required for cockpit temperature control.
Answer: B
Trim air adds controlled hot bleed air to conditioned air for fine temperature adjustment.
72. The AMS controls cabin temperature primarily by regulating:
A. Cabin altitude.
B. Engine N2.
C. Cooling pack output and trim air.
D. Outflow valve position.
Answer: C
The AMS controls cabin temperature by managing cooling pack performance and trim air (where
installed).
73. Which ECS feature is customer selectable?
A. Cooling packs
B. Ozone converters
C. Flow control valves
D. Recirculation fans
Answer: B
The ozone converter installation is a customer-selectable option.
74. Which system function provides the CPCS with airflow information to
anticipate cabin pressure changes?
A. Recirculation system
B. ECS flow rate calculation by the AMS
C. Trim air system
D. Ram-air system
Answer: B
The ECS supplies airflow rate data used by the CPCS to anticipate cabin pressure changes.
75. The primary controller responsible for all ECS functions is:
A. FADEC
B. CPCS
C. AMS controller located in SPDA 2
D. MAU 1
Answer: C
All air conditioning functions are controlled by the AMS, which is located in SPDA 2.
Excellent. This is the section that most Embraer operators emphasize during GenFam because it
tests system logic and mode transitions, not just component knowledge.
ATA 21 – Air Conditioning
Questions 76–90 (Cabin Pressurization Control System –
CPCS Operating Modes)
76. The primary function of the Cabin Pressurization Control System (CPCS) is
to:
A. Regulate pack outlet temperature.
B. Control cabin pressure by modulating the outflow valve.
C. Control trim air temperature.
D. Regulate bleed air pressure entering the packs.
Answer: B
The CPCS automatically maintains cabin pressurization by controlling the position of the
outflow valve throughout the flight.
77. Which component is the primary actuator used by the CPCS to regulate
cabin pressure?
A. Pack Flow Control Valve
B. Trim Air Valve
C. Outflow Valve
D. Safety Relief Valve
Answer: C
The CPCS regulates cabin pressure by continuously positioning the outflow valve.
78. During Ground Mode, the outflow valve is normally:
A. Fully closed.
B. Modulating to maintain cabin altitude.
C. Fully open.
D. Open 50%.
Answer: C
On the ground, the cabin is unpressurized and the outflow valve remains fully open.
79. The primary purpose of Ground Mode is to:
A. Pressurize the cabin before engine start.
B. Keep the aircraft unpressurized while on the ground.
C. Increase pack airflow.
D. Perform cabin leak checks.
Answer: B
Ground Mode keeps cabin pressure equal to ambient pressure.
80. During Taxi-to-Takeoff Mode, the CPCS begins to:
A. Fully open the outflow valve.
B. Gradually pre-pressurize the cabin.
C. Dump cabin pressure.
D. Disable automatic pressurization.
Answer: B
The CPCS begins pre-pressurizing the cabin to minimize pressure transients at liftoff.
81. Why does the CPCS pre-pressurize the cabin before takeoff?
A. To improve engine performance.
B. To reduce passenger discomfort during liftoff.
C. To increase bleed pressure.
D. To improve pack efficiency.
Answer: B
Pre-pressurization minimizes the sudden pressure change experienced during rotation.
82. During Climb Mode, the CPCS primarily controls:
A. Cabin temperature.
B. Cabin altitude by modulating the outflow valve.
C. Bleed manifold pressure.
D. ACM turbine speed.
Answer: B
During climb, the CPCS schedules cabin altitude by controlling outflow valve position.
83. Which statement best describes Cruise Mode?
A. Cabin altitude continuously increases.
B. Cabin pressure is maintained near the scheduled cruise cabin altitude.
C. The outflow valve is fully closed.
D. The safety valve regulates cabin pressure.
Answer: B
During cruise, the CPCS maintains the programmed cabin altitude.
84. During Descent Mode, the CPCS:
A. Gradually opens the outflow valve to reduce cabin differential pressure.
B. Closes the outflow valve.
C. Commands both packs OFF.
D. Activates the dump function.
Answer: A
The CPCS gradually opens the outflow valve to allow cabin pressure to decrease at a controlled
rate.
85. Which operating mode prepares the cabin to match airport elevation before
touchdown?
A. Cruise Mode
B. Ground Mode
C. Descent Mode
D. Taxi Mode
Answer: C
Descent Mode schedules the cabin altitude toward the destination airport elevation.
86. After landing, the CPCS transitions from Landing Mode to:
A. Cruise Mode
B. Climb Mode
C. Ground Mode
D. Dump Mode
Answer: C
Once landing is complete, the CPCS returns to Ground Mode with the outflow valve fully open.
87. Which statement correctly describes the Landing Mode?
A. The cabin is rapidly depressurized.
B. The cabin pressure is equalized with ambient pressure before Ground Mode.
C. The outflow valve remains fully closed.
D. Cabin differential pressure increases.
Answer: B
Landing Mode equalizes cabin and ambient pressure before Ground Mode.
88. The CPCS primarily determines cabin pressure by comparing:
A. Cabin temperature and outside air temperature.
B. Cabin pressure and ambient pressure.
C. Bleed pressure and hydraulic pressure.
D. Pack airflow and engine thrust.
Answer: B
The CPCS monitors cabin pressure relative to outside ambient pressure to regulate differential
pressure.
89. Which system provides the mechanical means of changing cabin pressure?
A. Cooling Pack
B. Recirculation System
C. Outflow Valve
D. Trim Air System
Answer: C
Changing the outflow valve opening changes the amount of air leaving the cabin, thereby
controlling cabin pressure.
90. Which statement best explains why the outflow valve is continuously
modulated during flight?
A. To maintain engine bleed pressure.
B. To regulate cabin pressure while balancing the inflow from the ECS packs.
C. To cool the avionics compartment.
D. To regulate trim air flow.
Answer: B
Since the ECS continuously supplies conditioned air, the CPCS modulates the outflow valve to
maintain the required cabin pressure by balancing inflow and outflow.
0
You can add this document to your study collection(s)
Sign in Available only to authorized usersYou can add this document to your saved list
Sign in Available only to authorized users(For complaints, use another form )