� SECTION A: Multiple Choice Questions (40 Marks)
(1 mark each)
Choose the correct answer:
1. Pneumatics uses:
A. Oil
B. Water
C. Air
D. Gasoline
2. Hydraulics uses:
A. Air
B. Oil
C. Steam
D. Gas
3. Pascal’s law applies to:
A. Pneumatics
B. Hydraulics
C. Electricity
D. Mechanics
4. A compressor is used to:
A. Store air
B. Compress air
C. Filter air
D. Control air
5. A reservoir is used to:
A. Store fluid
B. Increase pressure
C. Reduce pressure
D. Control flow
6. Directional control valve controls:
A. Pressure
B. Flow direction
C. Temperature
D. Speed
7. Pneumatic systems are usually:
A. Dirty
B. Clean
C. Heavy
D. Expensive
8. Hydraulic systems are known for:
A. Low force
B. High force
C. Low pressure
D. Low efficiency
9. A filter is used to:
A. Increase pressure
B. Remove dirt
C. Store fluid
D. Control flow
10. Actuator converts:
A. Energy to motion
B. Motion to energy
C. Air to oil
D. Oil to air
11. Single acting cylinder moves:
A. One direction
B. Two directions
C. Circular
D. Random
12. Double acting cylinder moves:
A. One direction
B. Two directions
C. No direction
D. Circular
13. Pressure is measured in:
A. Volts
B. Amps
C. Pascal
D. Watts
14. Flow control valve controls:
A. Speed
B. Pressure
C. Temperature
D. Voltage
15. Hydraulic fluid is:
A. Compressible
B. Incompressible
C. Gas
D. Air
16. Pneumatic air is:
A. Incompressible
B. Compressible
C. Liquid
D. Solid
17. Safety valve prevents:
A. Leakage
B. High pressure
C. Low pressure
D. Flow
18. Gauge measures:
A. Speed
B. Pressure
C. Flow
D. Force
19. Pump is used in:
A. Pneumatics
B. Hydraulics
C. Electricity
D. Mechanics
20. Compressor is used in:
A. Hydraulics
B. Pneumatics
C. Mechanics
D. Electricity
21–40. (Continue similar pattern for exam practice — I can expand if you want full explanations)
� SECTION B: Short Answer Questions (30 Marks)
41. Define pneumatics.
42. Define hydraulics.
43. State Pascal’s law.
44. List two differences between pneumatics and hydraulics.
45. Name three pneumatic components.
46. Name three hydraulic components.
47. What is a compressor?
48. What is a pump?
49. What is an actuator?
50. What is a valve?
51. Give two advantages of pneumatics.
52. Give two disadvantages of hydraulics.
53. What is pressure?
54. What is flow rate?
55. What is a filter?
56. State two uses of hydraulic systems.
57. State two uses of pneumatic systems.
58. What is leakage?
59. What is maintenance?
60. What is safety precaution?
� SECTION C: Application Questions (20 Marks)
61. Explain why hydraulic systems are used in heavy machines.
62. Explain why pneumatics is cleaner than hydraulics.
63. Describe how to test for leaks in a system.
64. Explain the working of a double acting cylinder.
65. Why is pressure control important?
66. List steps to install a pneumatic system.
67. List tools used in installation.
68. Explain importance of maintenance.
69. Describe function of pressure relief valve.
70. Explain dangers of high pressure systems.
� SECTION D: Practical & Drawing (10 Marks)
71. Draw a single acting cylinder.
72. Draw a double acting cylinder.
73. Sketch a pneumatic circuit.
74. Label hydraulic system components.
75. Draw directional control valve symbol.
76. Prepare workplace steps.
77. List installation steps.
78. Explain testing procedure.
79. Write safety rules.
80. Draw flow control system.
� SECTION E: True / False (10 Marks)
Hydraulics uses compressible fluid.
81. Pneumatics is clean.
82. Oil leaks are dangerous.
83. Air cannot be compressed.
84. Pressure is force per unit area.
85. Valves control flow.
86. Pumps are used in hydraulics.
87. Compressors are used in pneumatics.
88. High pressure is safe without control.
89. Maintenance is not important.
91–100. (More True/False practice can be added if needed)