CHAPTER 13 DIESEL ENGINE COOLING SYSTEMS Aeration - Correct Answer -A condition in which excessive amounts of air or steam bubbles are dissolved in coolant, diminishing the coolants effectiveness. Cavitation - Correct Answer -Erosion in cylinder blocks walls, heads, and liner sleeves as a result of the collapse of tiny water vapor bubbles formed when coolant vaporizes on hot cylinder wall surfaces. Coolant Extender - Correct Answer -An Additive package that is only used with ELC, which is added at the midpoint of the coolants life. Diesel Coolant Additive (DCA) - Correct Answer -An Additive used to treat cooling systems to reduce the effects of cavitation erosion. Electrolyte - Correct Answer -A substance that can Conduct current. Ethylene-Glycol - Correct Answer -The base chemical from which the majority of Anti-freezes are made. Extended-Life Coolant (ELC) - Correct Answer -Several Types of long-life coolant formulations containing an anti-corrosion additive package that does not deplete; Also known as long-life coolant (LLC). Heat Exchanger - Correct Answer -A system that transfers heat from the coolant to the Atmosphere. Heat Rejection - Correct Answer -The transfer of heat into the cooling system from the combustion chamber. Hybrid Organic Acid Technology (HOAT) - Correct Answer -A combination of IAT And OAT with nitrites added, making it suitable for both use in both light- And Heavy duty systems. Inorganic Additive Technology (IAT) - Correct Answer -A diesel engine cooling system conditioner containing non-carbon-based corrosion inhibitors Such as phosphate, borates, and silicate. Nitrated-Organic Acid Technology (NOAT) - Correct Answer -An ELC Using OAT with Nitrates added. Organic Acid Technology (OAT) - Correct Answer -A category of ELC containing carbon-based corrosion inhibitors. Propylene-Glycol - Correct Answer -An anti-freeze base that is non-toxic and environmentally friendly. Supplemental Coolant Additive (SCA) - Correct Answer -An Additive used to treat cooling systems to reduce the effects of cavitation erosion and optimize cooling system performance. Thermal Efficiency - Correct Answer -The ability of an engine to convert the energy content of fuel into mechanical energy. 40% - Correct Answer -Manufacturers studies report as much as _____ Of all engine maintenance or breakdown is related directly or indirectly to cooling Systems. Over 50% - Correct Answer -Of Catastrophic engine failures can be attributed to cooling system failures 60% - Correct Answer -Of Water pump failures are caused by preventable seal leakage. Diesel Cooling Systems - Correct Answer -Also need specialized attention because of unique heat loads and combustion characteristics that affect coolant maintenance practices. 3900 F - Correct Answer -The Flame Temperature of diesel fuel is approximately The Cooling System Removes - Correct Answer -Excess heat from the engine and releases it to the Atmosphere through the radiator. Todays Engines More Than Half the heat produced from combustion - Correct Answer -Is Wasted through heat radiated from engine surfaces and dissipated from the engine through the cooling system and exhaust gases. Thermal Efficiency Is measured - Correct Answer -As a percentage of the potential energy content in fuel compared with the engines ability to convert the potential energy into mechanical energy. A Simplified Way of Stating Thermal Efficiency - Correct Answer -Would be to compare the mechanical energy available at the flywheel to the cost of fuel. Approximately 45% Thermal Efficiency - Correct Answer -Currently, The best heavy-duty on highway diesel engines operate at. Which means that 45% of the fuel energy released during combustion is converted into mechanical energy and available to the flywheel. 30-35% - Correct Answer -How much of The remaining energy is absorbed by the cooling system. 20-25% - Correct Answer -How much is emitted by the exhaust system. 5% - Correct Answer -Is radiated to the Atmosphere through hot engine parts. Friction And The Energy Required To Move Gases in And Out - Correct Answer -Of the Engine account for the remaining losses in thermal efficiency. More than 50% Thermal Efficiency - Correct Answer -Larger, Slow- Speed Industrial diesel engines used on Ships and for electric power generation can operate at more than. 17% - Correct Answer -Greenhouse Gas (GHG) Emission standards for heavy-duty diesels require an increase in thermal efficiency for diesel engines by 2025. 25-30% Thermal Efficiency - Correct Answer -The Thermal Efficiency of todays diesel engines is almost double that of spark-ignition engines, which operate at up to approximately. Recapturing Energy - Correct Answer -That would normally be lost in the exhaust system to power a turbo charger can increase the thermal efficiency of a diesel engine; This one way that heat energy is removed by diesels. Higher compression Ratios, Lean Burn Combustion, The absence of a throttle Valve. - Correct Answer -Why is the Thermal Efficiency of Diesel Engines higher than that of Petrol Engines? Compression-Ignition Combustion - Correct Answer -Is one of the most thermally efficient processes for converting fuel energy into mechanical energy, It still requires a substantial amount of heat being released to the cooling system. Cooled (EGR) - Correct Answer -Which has been used by diesels for the past decade and a half, places even lager heat load on the cooling system. Up to 30% - Correct Answer -Of intake air mass in most current diesels will include exhaust gases, which can Reach 1200F 1200F - Correct Answer -Exhaust Gases can reach? 400F - Correct Answer -Exhaust Temperatures (1200F) are reduced to how much or less before being mixed with the intake air. Originating from the outlet of the Charge Air Cooler. 15-40% - Correct Answer -Diesel-Powered Vehicles cooling system needs to Dissipate _________ More heat absorbed from exhaust gas. 100% - Correct Answer -Until Model year 2002, when cooled EGR was introduced, Most diesels had how much of exhaust heat passed into the atmosphere. Larger Water pumps, Cooling Fans, And radiator Cross-sectional areas combined with increased under hood airflow are needed to remove the additional heat from the cooling system. - Correct Answer -Engine modifications to deal with the increased heat loads include. Heat Generated By Combustion is - Correct Answer -Rejected and transferred to engine parts and lubrication oil. If Excess heat is not removed from the oil. - Correct Answer -It can lose its viscosity and thin too much to support bearing loads and properly lubricate parts. 250F - Correct Answer -At temperatures above ________, Oil can quickly oxidize and even burn. 400F - Correct Answer -Intake air compressed by the turbocharger easily heats to over? Series Turbo Charging - Correct Answer -Temperatures are even higher than 400 degrees on engines using. Most Engines Use Air To Air After cooling (ATAAC) - Correct Answer -Engine coolant is often used to help reduce charge air temperatures, Which lower Air Inlet Temperatures. Liquid Interstage Coolers - Correct Answer -Are used on Series turbo charged engines to reduce, air temperatures between the LOW- And HIGH- pressure turbochargers. Heat Removed from intake air - Correct Answer -Is simply Transferred to the atmosphere through the radiator. Higher Operating Temperatures - Correct Answer -Will lower the amount of heat rejected, but if temperatures climb even as 12F beyond normal range, cylinder wall wear begins to dramatically increase. 12 F Beyond Normal operating Range - Correct Answer -Cylinder wall wear begins to dramatically increase. Cooling systems must provide - Correct Answer -For expansion of coolant. It Expands - Correct Answer -As engine coolant Warms, An Over-Flow Reservoir - Correct Answer -Is needed to Contain the coolant pushed out of the radiator and engine. Surge Tanks, Overflow Reservoirs And large Radiator Tanks - Correct Answer -Are used to buffer coolant expansion. When the Engine Cools - Correct Answer -Coolant Is drawn back into the radiator through negative pressure induced by the contraction of cool coolant in the closed cooling system. First- Is to maintain pressure greater than atmospheric pressure at the water pump inlet. Second The Second Important reason for pressurizing the cooling system is that it increases the boiling point of water. - Correct Answer -Cooling Systems Are pressurized for two important reasons. Resulting In Cracking of heads and Engine Blocks. - Correct Answer -Even Momentary loss of direct coolant contact with coolant would cause severe thermal stress on these components. Increasing Cooling System Pressure will prevent - Correct Answer -Engine damage and loss of coolant by increasing the temperature at which coolant will boil. Every 1 PSI Increase - Correct Answer -In cooling system pressure increases the boiling point by approximately 3 F, This means 10psi of pressure on the cooling system raises its boiling point to 242 F Pressurizing The Cooling Systems - Correct Answer -Also prevents water from boiling away from the cooling system. The Coolant System Is pressurized by - Correct Answer -Both Coolant expansion and Trapped Air, Including Steam trapped in the radiator during heating. Coolant Systems Must provide for - Correct Answer -Deaeration Of coolant to prevent pumps and coolant passage ways in the cylinder head from becoming Air bound, Or blocked by an accumulation of steam. As Coolant Warms - Correct Answer -Some Vaporization occurs, forming bubbles and vapor pockets. Even When Coolant Is Relatively Cold - Correct Answer -Coolant next to hot interior engine surfaces becomes hotter than surrounding coolant and vaporizes. Galvanic Activity In a cooling System is measured. - Correct Answer -With a Digital Multi Meter. Setting The Multi-Meter to a low-voltage DC Scale - Correct Answer -One test lead is placed in the coolant . The other test lead can be placed anywhere on the engine where metal is exposed. 0.2 Volts or Less - Correct Answer -A cooling System with a level of Additives that is adequate to protect metals from corrosion will test at Will Produce More Voltage - Correct Answer -Coolant that has become depleted of additives or highly acidic or alkaline. 2 Volts - Correct Answer -If the Voltage exceeds ________ the cooling system should be drained and flushed, And new coolant that contains the recommended level of conditioners should be added. Dissimilar Metals In Contact with Engine Coolant - Correct Answer -Cause electrochemical reactions The Coolant Is an electrolyte - Correct Answer -Which means it can conduct current. The Cooling system can behave like a - Correct Answer -Primary battery in which dissimilar metals in the presence of an electrolyte will produce a flow of electric current. Galvanic Effect - Correct Answer -These principle of inducing current flow by using dissimilar metals and electrolyte is called the. Some metals in contact with coolant will be - Correct Answer -Severely and quickly corroded through these chemical reactions. Scale And Deposits On Internal Surfaces - Correct Answer -Within the engine and cooling system can sharply reduce heat transfer. 0.06 - Correct Answer -deposit will reduce heat by 40% 40 percent - Correct Answer -0.06 deposits will reduce heat by how much. Scale - Correct Answer -Can come from Calcium and magnesium in the water used for cooling. Phosphate, Silicate, And Nitrate - Correct Answer -Some scale is produced by additives in the antifreeze such as Hot engine Surfaces where coolant turbulence is low. - Correct Answer -Scale And Deposits formation Commonly occur on. Water - Correct Answer -Is the primary ingredient of engine coolant. Cylinder heads, blocks, water pumps, and radiators - Correct Answer -Frozen Coolant can easily break and Crack Core plugs AKA Frost Plugs - Correct Answer -Are pushed out by frozen coolant, which causes a major loss in coolant. Core Plugs - Correct Answer -Are not designed to relieve pressure from frozen coolant to prevent engine damage. When coolant is Frozen - Correct Answer -It will not flow, which will cause the cylinder components to rapidly over heat, Thermally stressing the cylinder block and head to the point of cracking. Boiling Coolant - Correct Answer -Is not able to effectively absorb heat, because heat it is not in a liquid state. Antifreeze AKA Coolant - Correct Answer -Freeze and boil protection are both provided to the engine by the use of. Core plugs or Frost plugs are used to seal - Correct Answer -passage ways in cylinder blocks and head casting designed to flush sand from casting after manufacturing. Cavitation Erosion is Caused by - Correct Answer -The collapse of tiny water vapor bubbles formed when coolant rapidly heats next to hot surfaces , or the coolant is subjected to a rapid drop in pressure. 60,000 PSI - Correct Answer -Pressure exerted by the force of bubble collapse is reported to be as high as. Chemical Treatment of the cooling systems - Correct Answer -Is the preferred method for minimizing cavitation erosion. Nitrite - Correct Answer -Both new and old formulations of anti-freeze for diesel engines use a critical additive to minimize cavitation erosion. Intake Manifold to circulate coolant, Which lowers air inlet temperatures. - Correct Answer -Liquid heat exchangers, charge air coolers, or after coolers. Oil Cooler Nozzles - Correct Answer -Spray the underside of all engine pistons crowns with oil to remove heat. The heat is absorbed by the oil is removed by the cooling system through the oil cooler. Between 180F And 200F - Correct Answer -Machined Parts operating with close tolerances require consistent operating temperatures. 230F - Correct Answer -An exception is emergency and military engines that are designed to withstand as much as Cavitation Occurs - Correct Answer -More easily if cooling system pressures are abnormally low. The Sharp Increase in Combustion Pressure Also creates - Correct Answer -Temporary pressure voids on the coolant side of the blocks cylinder walls, which produce cavitation erosion. All Diesel cooling Systems - Correct Answer -Need to use special conditioners to prevent or minimize cavitation erosion. Organic Acid technology (OAT) And Inorganic Additive Technology (IAT) - Correct Answer -There are two categories of conditioner. Both OAT And IAT Were primarily developed - Correct Answer -To treat or condition the cooling system to reduce the effects of Cavitation erosion. Nitrite, When Added to Coolant - Correct Answer -Forms a Thin, Protective film on the coolant side of the engine cylinder walls and other surfaces to reduce cavitation erosion. Vapor Implosion In an engine protected by Nitrite - Correct Answer -Will Damage only the nitrite layer, which can be replenished from the nitrite dissolved in the coolant. A cooling System Maintenance - Correct Answer -must include the measurement of the level of nitrite to evaluate the level of this important additive. Coolant in the cylinder of a diesel - Correct Answer -Will lock the engine because cylinders have a very little clearance volume. One side of the head gasket - Correct Answer -Typically has more or larger holes than the other. The largest holes are located - Correct Answer -On the opposite side of the gasket from the thermostat. This requires coolant to flow across the head to properly cool the head before reaching the thermostat housing. Water mixed with Antifreeze And other ingredients - Correct Answer -Is the primary coolant medium to absorb engine heat. Water - Correct Answer -Is the most efficient fluid to transfer heat. pH Levels - Correct Answer -One Major factor affecting the corrosion rate of the metals in an engine is the coolants? 0-14 With 7 Being Neutral - Correct Answer -A materials pH is measured on a scale of 8.5 And 10.5 - Correct Answer -Coolant And pH should be maintained between. If coolant drops below 8.5 - Correct Answer -It will become aggressive to ferrous metals (cast iron and Steel) Aluminum, copper, and brass. If it coolant Increases above 11 - Correct Answer -It will become aggressive to aluminum and Solder in a cooling system. Distilled Water - Correct Answer -Is best for cooling systems because it has no mineral content to scale or deposit, on a cooling system. higher Than 60% or lower than 40% - Correct Answer -The Anti-freeze in the water mixture should never be. coolant with less than 40% - Correct Answer -Concentration of anti-freeze may not contain enough corrosion inhibitors. Over 65% - Correct Answer -Concentration and the coolant will not remove heat effectively and will in fact lose its freeze protection. A 50/50 Mixture - Correct Answer -Is optimal for removing heat and providing corrosion protection. Green Dye - Correct Answer -Is later added for identification. one of the most significant reasons ethylene glycol is dyed is to clearly distinguish it from other coolants, because it is extremely poisonous. Glycerin-Based - Correct Answer -Cummins makes currently produces a anti-freeze, complete that meets the recently developed ASTM international standard for the latest antifreeze technology. The Primary disadvantage Of Glycerin - Correct Answer -Is that its freeze protection temperature is high in comparison to ethylene Glycol. Diluted to a 30/70 Water-to glycerin concentration - Correct Answer -Glycerin can only provide a freeze protection to -36F. At that concentration glycerin-based coolant is not able to remove as much heat as a mixture with higher amount of water. -36F - Correct Answer -Glycerin can only provide a freeze protection to Antifreeze contains Corrosion inhibitors - Correct Answer -To protect cooling systems materials such s cast iron, aluminum, copper, brass, solder and many non- metallics like nylon and silicon. Type 1 conventional Anti-freeze - Correct Answer -uses older additive technology and contains corrosion inhibitors, such as boron, phosphate, sodium silicate. Sodium Silicate - Correct Answer -Is primarily used to protect aluminum and is found in much higher concentration when used in gasoline engines with alumininum cylinder heads. sodium silicate and nitrite - Correct Answer -both these additives together will cause a condition known as silicate dropout. Silicate Dropout - Correct Answer -Is characterized by the appearance of green "Goo" or gel that plugs radiator and heater core tubes, leading to over heating of the engine and even catasphropic failure Phosphate Protects - Correct Answer -Iron And pH control (keeps coolant alkaline between (8.510.5) Nitrite Protects - Correct Answer -Cast iron, Steel, Aluminum, And Solder Type III Fully formulated Propylene Glycol extended-life OAT - Correct Answer -Suggested color Blue Type I Additive Deplete - Correct Answer -Quickly and require monitoring. With time, Many of these Additives other components, Such as phosphorus, drop out with the silicate, coating cooling system component's with a layer of slime and deposits. Type I Anti-freeze - Correct Answer -containing this corrosion inhibitor package should be drained and replaced every two years. Between 3% And 5% Of DCA or SCA - Correct Answer -Is added after the initial mixing of anti-freeze and water to bring the additive package for diesel engines to the correct protection level. Type I Anti-freeze for diesel Engines - Correct Answer -Is different from type I Anti-freeze for gasoline engines and the two should never be exchanged. Gasoline Engines Use Type I Anti-Freeze that contain higher Silicate levels. Only Low-Silicate Anti-freeze - Correct Answer -Should be used in diesel engines because the addition of nitrite to diesel coolant will cause silicate dropout, Which can lead to plugged Radiators, Water pump seal leaks, and overheated engines. Type II Anti-Freeze - Correct Answer -Is made from ethylene glycol. Type III Anti-Freeze - Correct Answer -Is made from propylene Glycol. Type II And Type III - Correct Answer -These Anti-freezes generally do not require An initial charge of DCA or SCA because it is incorporated into the solution during Manufacture. 600,000 Miles on Road, Or 12,000 hours off-road. - Correct Answer -The corrosion inhibitors in these types of ELC Anti-freeze are designed to last. A Coolant Extender - Correct Answer -That contains Nitrite for protection against cavitation erosion has an additive similar to SCA/DCA. 300,000 Miles or 6000 Hours - Correct Answer -A coolant Extender must be added only once at (482,800 km) which is about halfway through the anti-freezes service, if a longer service is expected. Type IV Anti-freeze - Correct Answer -This Red colored anti-freeze is commonly used in todays diesel and gasoline engines, This Type of anti-freeze use non-carboxylate acids, such as benzoate, from benzoic acid, to form the additive package. Currently No Vehicle OEM Uses a factory of NOAT Anti-freeze. - Correct Answer -Nitrated Organic Acid Technology (NOAT) Five years Or 150,000 miles - Correct Answer -The Normal NOAT service life, And uses an extender package halfway through the service life. Mixing IAT with OAT, HOAT, And NOAT Anti-freezes - Correct Answer -Will not damage the engines cooling system. However, mixing anti-freezes nullifies the extended-life attributes of these formulations. 5% to 25% - Correct Answer -Depenfing on the type of formulation, acceptable contamination can range from. Though most OEMs do not recommend contamination of 5% Short Out - Correct Answer -Sensors and other electrical devices that are exposed to engine coolant have the potential to Electrical Current - Correct Answer -Passing through the coolant will quickly erode brass and aluminum oil coolers, injector tubes, and other metals in the cooling system. Ground Straps - Correct Answer -To minimize Electrical Current, engine blocks use a number of what, to not only lower resistance for engine-mounted electrical devices but also to minimize electrical conduction through engine coolant. Electrical Conduction - Correct Answer -Through coolant quickly eliminates nitrite additives in coolant, leading to further engine damage If Coolant is brown in color, - Correct Answer -it often indicates the presence of rust in the coolant. some corrosion inhibitors used to prevent are easily damaged by over heating coolant. coolant that has overheated should not be reused during service. The Primary function of the cooling system - Correct Answer -Is Transferring heat absorbed from the engine to the Atmosphere. Radiators - Correct Answer -Are Heat exchanging devices that release heat into the atmosphere from the engine to the air. Coolant can flow in a radiator in two ways. Down-Flow Radiators - Correct Answer -The coolant will enter through a hose connected to the top of the tank that is carrying hot coolant from the water pump outlet. The coolant will then flow from the top tank, through cooling tubes, and into the bottom tank. In Cross-Flow Radiators - Correct Answer -Coolant will flow from a top-connected hose, through a side-mounted tank, into cooling tubes, and across the radiator to another side -mounted tank. Cross-Flow Radiators Are preferred - Correct Answer -In Vehicles with low-profile aerodynamic hoods because they can be made wider with a lower height profile. In The 1980s - Correct Answer -Most Manufacturers began to use aluminum tube radiators. A Two-Row Aluminum Radiator core - Correct Answer -Also referred to as a double core radiator with a 1" Circumference tubes is equivalent to a five-row copper brass radiator with 1/2" circumference tubes. The 1" Tube Size - Correct Answer -Also increased tube-to-fin contact and cooling capacity by roughly 25% A Vacuum Valve Incorporated into the cap - Correct Answer -Allows Air to coolant to Re-enter the cooling system when the pressure drop after the engine cools. Faulty Vacuum Valves - Correct Answer -Are often identified when the upper radiator hoses collapse after the engine cools or when coolant is lost. 85% - Correct Answer -The Radiator cap is also important to water pump efficiency. When the cooling system is pressurized, the pumps operates much better than the How Much Efficiency without pressure cap. Constant Torque Clamps - Correct Answer -Are the best clamps to use to minimize coolant loss, because they change dimensionally with the expansion and contraction of hoses and connections. Vent Lines - Correct Answer -Located at the highest points on the engine and radiator bleed any steam and air out of the engine and into the surge tank. Pumps can be - Correct Answer -Belt - or gear driven A Gear Driven Pump - Correct Answer -Does not rely on a belt, which minimizes service requirements and is more reliable than a belt for long distances. All Water Pumps - Correct Answer -Are centrifugal turbine pumps, which means they become more efficient the faster they turn. Thermostats - Correct Answer -Regulate the temperature of the engine coolant by modulating or controlling the volume of coolant circulated to the radiator. 180F - Correct Answer -At a predetermined point (82C) The Thermostat will begin to open, and it will continue to open further if the coolant temperature continues to increase. A Blocked Thermostat - Correct Answer -Has a Hollow center. Coolant Flow is Regulated - Correct Answer -By Movement of the outer sleeve to block or open passage ways to either the radiator or bypass hose. Choking And full blocking thermostats operate by using - Correct Answer -A special wax pellet combined with a powered metal tightly squeezed into a copper cup that is equipped with a piston inside a rubber boot. Heat causes the wax pellet to expand, which pushes the piston upward, opening the valve. Engine Fans - Correct Answer -Are designed to increase the airflow across the radiator, which improves the efficiency of heat removal from coolant. A Fan Drive mechanism is used to decouple the fan from the engine when airflow is not required. Correct Answer -To reduce the parasitic loss of power from the engine, which is often more than 25 horsepower (HP) on some heavy duty Fans. An Electrically controlled Variable speed engine fan - Correct Answer -Reduces parasitic power loss and provides optimal ECM control of fan speed. A More Traditional fan engagement Mechanism Is an ON/OFF fan hub - Correct Answer -Which Uses air pressure to either engage or release a spring-loaded friction clutch. 90-120 Seconds - Correct Answer -typically a timer will be connected to the circuit to keep the fan engaged for...to prevent excessive cycling between on and off which will wear out the friction clutch faster. 10-15F - Correct Answer -The temperature at which the fan will engage is how much above the coolant operating temperature. 25HP - Correct Answer -Engine fans consume a lot of power easily 19kW on heavy duty engines, the fan is often activated with the engine brake to increase the engine resistance to driveline rotation. Hose clamps - Correct Answer -help the hose seal at its connections. Constant Torque spring clamps - Correct Answer -Allow hose to ends to thermally expand and contract, which minimize coolant loss from hose clamps. A Refractometer - Correct Answer -Is used to test coolant mixture and freeze protection by testing the fluids ability to bend light. This tester can be used with any type of anti-freeze. A pressure tester, Refractometer - Correct Answer -Common tools needed to service cooling. 15-17 PSI - Correct Answer -An adapter may be required to seal the tool to the neck of the surge tank or radiator. pressurize the system to. White Exhaust Smokes that smells sweet - Correct Answer -Is an indication of an EGR Cooler leak. the problem can worsen with hard acceleration. leaking Head Gaskets, Or Air Compressors Can Consume Coolant - Correct Answer -Loss of engine coolant without any visible external leaks may be caused by a variety of internal leaks or overpressurizing of the cooling system forcing coolant out the over-flow tank. Optical Tachometer - Correct Answer -To evaluate these silicone fluid thermostatic fan clutches, the amount of slippage is measured. This is best done with a Any Fluid Leakage And Damaged Hubs - Correct Answer -Should be taken out of service. A weekend hose may - Correct Answer -collapse and restrict coolant flow. The bottom radiator hose has an internal spring that prevents the hose collapsing when the engine is suddenly accelerated and the water pump draws more coolant. Upper Radiator Hoses - Correct Answer -More commonly fail first. The use of a Hydrometer or Refractometer - Correct Answer -Is Necessary when testing the freeze protection of the coolant in the cooling system. A Refractometer can also be used - Correct Answer -To test the proportions of anti-freeze and water in the coolant mix ( Or the level of freeze protection) by measuring a liquids specific gravity.
0
You can add this document to your study collection(s)
Sign in Available only to authorized usersYou can add this document to your saved list
Sign in Available only to authorized users(For complaints, use another form )