Lecture # 4
Introduction to Fluid Mechanics
Fluid Mechanics-I (ME321)
1
Interesting Phenomenon
Why is it that a drop of blood forms a hump on a horizontal glass?
A drop of mercury forms a near-perfect sphere and can be rolled just
like a steel ball over a smooth surface?
Water droplets from rain or dew hang from branches or leaves of trees?
A soap bubble released into the air forms a spherical shape?
Water drop on lotus leaf
Water repellent and self cleaning effect
Insect walking on water surface
2
Surface Tension – Floating Razor Blade
A heavier-than-water, double-edged steel razor blade can float on water.
Without surface tension, the blade would sink because its weight is greater
than its buoyant force. However, surface tension forces are not large
enough to support a slightly heavier single-edged blade.
3
Interface
Liquid, being unable to expand freely, will form an interface with a
second liquid or gas.
At the interface between a liquid and a gas, or between two immiscible
liquids, forces develop in the liquid surface that cause the surface to
behave as if it were a “skin” or “membrane” stretched over the fluid
mass.
Interface
Less dense
Molecules
High Density
of Molecules
4
Surface Tension
A blade will float on water if placed gently on the surface because the
tension developed in the hypothetical skin supports it.
Small droplets of mercury will form into spheres when placed on a
smooth surface because the cohesive forces in the surface tend to hold
all the molecules together in a compact shape (spherical??).
5
Surface Tension
This surface phenomenon is due to unbalanced
cohesive forces (attractive forces) acting on the
liquid molecules at the fluid surface.
Molecules along the surface are subjected to a
net force toward the interior (pull inwards). The
liquid molecules tend to minimize their surface
area because of surface tension.
The intensity of the molecular attraction per unit
length along any line in the surface is called the
Surface Tension 𝝈 (N/m or lb/ft).
The value of surface tension decreases as
temperature increases
6
Surface Tension in a Spherical Droplet
Free-body diagram: Forces acting on one-half of a liquid drop
Pressure drop across the surface of the droplet. If the drop is cut in half, the force developed
due to surface tension will be 2𝜋𝑅𝜎. This force must be balanced by the pressure difference
∆𝑝, between the internal pressure, and the external pressure, acting over the circular area:
2 R p R 2
p pi pe
2
R
Pressure higher on concave
side. E.g. Balloon
If the interface is curved, then there is a pressure difference across the interface, the
pressure being higher on the concave side (drop of fluid, bubble)
Note that the excess pressure in a droplet or bubble is inversely proportional to the radius.
What about soap bubble?
7
Capillary tube
The rise or fall of liquid in a narrow tube is due to the combined effect of
contact angle and surface tension. This is known as Capillary Effect.
There is an attraction (adhesion) between the wall of the tube and liquid
molecules which is higher than cohesive forces (cohesion) within the
water molecules. Wetting fluid.
8
Liquid rise in Capillary tube
W
This is a liquid–gas–solid
interface
Effect of capillary action in small tubes. (a) Rise of column for a liquid that wets the
tube. (b) Free-body diagram for calculating column height. (c) Depression of
column: If adhesion of molecules is weaker than cohesion between molecules
non wetting liquid
The height h is governed by the value of the surface tension, 𝜎, tube radius, R,
specific weight of the liquid, 𝛾, and the angle of contact, 𝜃 between the fluid and
tube.
Vertical force due to the surface tension balances the weight of the fluid as:
R 2 h 2 R cos
Height, inversely proportional to tube radius.
Capillary action is more for smaller radius.
2 cos
h
Jurin’s Law
9
R
Surface Tension in a Droplet
Contact-angle effects at liquid–gas–solid interface. If θ < 90,
the liquid “wets” the solid (hydrophilic surface); if θ > 90, the
liquid is nonwetting (hydrophobic surface).
10
Capillary rise
11
Liquid rise in Capillary tube
Example 1.8: Pressures are sometime determined by measuring the height of
a column of liquid in a vertical tube. What diameter of clean glass tubing (𝜃 =
0°) is required so that the rise of water at 20ºC in a tube due to capillary action
(as opposed to pressure in the tube) is less than 1.0 mm?
h
2 cos
R
R
2 cos
h
For water at 20ºC (from Table B.2), 𝜎 = 0.0728 N/m and
𝛾 = 9.789 kN/m3. Since 𝜃 = 0° it follows that for h = 1.0
mm,
R
2 0.0728 N/m 1
9.789 10 N/m 1.0 mm 10 m/mm
3
3
3
Allowable capillary rise is decreased, the
diameter of the tube must be significantly
increased
0.0149 m
And the minimum required tube diameter, D, is
D 2 R 0.0298 m 29.8 mm
12
Liquid rise in Capillary tube – Straight channel & Porous media
Leaf
Paper soaking: Capillary
imbibition in porous media
13
Chapter Summary
14
Derive the expression for the surface tension in a half cut soap bubble.
Apply this expression to find out the gage pressure inside the bubble
with a) 0.2 cm diameter and b) 5 cm diameter. Use surface tension 𝜎 =
0.025 N/m. Explain the difference in pressure value for both radii.
Hint: Free-body diagram of a soap bubble given:
15
Sample Problems Chapter 1
Course Book: Fundamentals of Fluid Mechanics, Munson, 7th Edition
Problems:
1.3, 1.6, 1.7, 1.13, 1.15, 1.20, 1.21, 1.30, 1.36, 1.38, 1.41, 1.47, 1.58, 1.64, 1.77, 1.78, 1.86, 1.87,
1.89, 1.104, 1.111, 1.118, 1.124, 1.125, 1.126, 1.129, 1.131.
Quiz 1in next class
Similar to sample problems.
16