A. Properties of Steam
1. Saturated Liquid
Water that is about to vaporize at a given pressure and temperature.
2. Saturated Vapor
Steam that is about to condense at saturation conditions.
3. Wet Steam
A mixture of saturated liquid and saturated vapor.
4. Superheated Steam
Steam at a temperature higher than the saturation temperature at a given pressure.
5. Quality (Dryness Fraction, x)
The mass fraction of vapor in wet steam.
6. Specific Volume (v)
Volume occupied per unit mass of steam.
7. Specific Enthalpy (h)
Total energy content of steam per unit mass.
8. Specific Entropy (s)
Measure of energy dispersal or disorder per unit mass.
9. Saturation Temperature
Temperature at which water boils at a given pressure.
10. Critical Point
State where liquid and vapor phases become indistinguishable.
B. Steam Tables & Diagrams
11. Steam Tables
Tables listing thermodynamic properties of water and steam.
12. Saturated Steam Table
Contains properties at saturation conditions.
13. Superheated Steam Table
Contains properties at temperatures above saturation.
14. Compressed Liquid
Liquid at a pressure higher than saturation pressure.
15. T–s Diagram
Temperature–entropy plot used to analyze Rankine cycles.
16. h–s (Mollier) Diagram
Enthalpy–entropy plot commonly used for turbine analysis.
C. Heat Engines & Power Cycles
17. Heat Engine
A device that converts heat into work.
18. Thermal Efficiency
Ratio of net work output to heat input.
19. Power Cycle
A thermodynamic cycle that produces net work.
20. Working Fluid
The fluid that undergoes thermodynamic processes in a cycle.
D. Rankine Cycle (General)
21. Rankine Cycle
Ideal cycle that models steam power plants.
22. Boiler
Component where heat is added to water at constant pressure.
23. Steam Turbine
Device that converts steam energy into mechanical work.
24. Condenser
Component where steam rejects heat and becomes liquid.
25. Feedwater Pump
Raises the pressure of liquid water entering the boiler.
E. Ideal Rankine Cycle
26. Ideal Rankine Cycle
Rankine cycle assuming no irreversibilities.
27. Isentropic Process
Process with constant entropy.
28. Isentropic Turbine Expansion
Ideal turbine process with maximum work output.
29. Isentropic Pump Compression
Ideal pumping process with minimum work input.
30. Constant Pressure Heat Addition
Heat addition in the boiler.
31. Constant Pressure Heat Rejection
Heat rejection in the condenser.
F. Reheat Rankine Cycle
32. Reheat
Process of reheating steam between turbine stages.
33. High-Pressure Turbine (HPT)
First turbine stage in a reheat cycle.
34. Low-Pressure Turbine (LPT)
Second turbine stage after reheating.
35. Reheater
Heat exchanger used to raise steam temperature again.
36. Moisture Content
Amount of liquid present in steam at turbine exit.
G. Actual Rankine Cycle
37. Actual Rankine Cycle
Rankine cycle that includes real system losses.
38. Turbine Efficiency
Ratio of actual turbine work to isentropic work.
39. Pump Efficiency
Ratio of isentropic pump work to actual work.
40. Pressure Drop
Loss of pressure due to friction in components.
41. Irreversibility
Loss of useful work due to friction and heat loss.
42. Entropy Generation
Increase in entropy caused by irreversibilities.
H. Performance Parameters
43. Net Work Output
Difference between turbine work and pump work.
44. Back Work Ratio
Ratio of pump work to turbine work.
45. Heat Rate
Heat input required per unit power output.
46. Cycle Efficiency Loss
Reduction in efficiency due to non-ideal processes.
Ideal Rankine Cycle
An idealized, closed thermodynamic cycle that converts heat into mechanical work using
water/steam as the working fluid, assuming no friction, no heat loss to the surroundings,
and perfect efficiency in the pump and turbine
compression process in the pump and the expansion process in the turbine are assumed
to be isentropic (constant entropy
Actual Rankine Cycle
Actual Rankine Cycle is the model used to analyze real-world power plants by
incorporating the irreversibilities (losses) that occur in physical components
A thermodynamic cycle that describes the actual operation of a steam power plant by
including irreversibilities such as fluid friction, heat losses to the surroundings, and nonideal performance of the pump and turbine.
Turbine and Pump: The processes are not isentropic (entropy increases
Boiler and Condenser: Pressure drops occur due to friction in the piping and heat
exchangers
Thermal Efficiency The ratio of the net work output of the cycle to the heat input to the cycle
Specific Enthalpy The total energy content of the fluid per unit mass encompassing its
internal energy and the energy required to push it through the system (flow work).