Advances in Wind Engineering 2 (2025) 100083 Contents lists available at ScienceDirect Advances in Wind Engineering journal homepage: www.keaipublishing.com/en/journals/awe Study on liquid film dynamics and aerodynamic characteristics of train-bridge system under wind-rain interaction effects using Eulerian-Lagrangian approach ]] ]] ]]]]]] Mingwei Donga, , Rui Lia, Jianlin Xua, Yongxing Jiaa, Yonggang Yanga, Tao Zhaoa, Jiahui Chenb ⁎ a b School of Mechanical Engineering, Lanzhou Jiaotong University, Lanzhou, China School of Civil Engineering, Central South University, Changsha, China A R T I C L E I N F O Keywords: High-speed train Wind–rain coupling Aerodynamic characteristics Numerical simulation A B S T R A C T This study investigated liquid film dynamics and aerodynamic performances of a high-speed train on bridges in rainy conditions using Eulerian-Lagrangian approach. The effects of rainfall intensity and train speed on liquid film distribution and dynamics as well as aerodynamic performances of the train were investigated system­ atically. The spatial distribution of raindrops and liquid film properties on the train were examined, followed by an analysis of the impacts of rainfall/train speed on the aerodynamic characteristics of the train—including forces, pressure distributions and wake dynamics. Aerodynamic characteristics around the train and in the wake were quantified via probe points. It was found that rainfall intensity is the main factor for liquid-phase dis­ tribution on the train. Windward surfaces exhibited significant raindrop accumulation, with liquid film thickness increasing synchronously with both rainfall intensity and train speed. At 350 km/h, the maximum liquid volume fraction (LVF) increased by 243.9 % as rainfall intensity rose from 100 to 500 mm/h. The maximum liquid film velocity increased by 43.21 % when train speed rose from 250 to 350 km/h under 500 mm/h rainfall. While both rainfall and train speed influence aerodynamic forces of the train, train speed governs global variation trends. Leeward flow demonstrated heightened sensitivity to rainfall, exhibiting substantial disparities in velocity, pressure and turbulent kinetic energy (TKE) distributions. Flow disturbance amplitude at probe points pro­ gressively decayed with increasing height. 1. Introduction High-speed railways are continually extending towards coastal and mountainous regions with their rapid development. Consequently, the percentage of bridges in the high-speed railway has been increasing stea­ dily. However, the frequency of trains encountering severe weather con­ ditions (e.g., strong winds and heavy rain) during operation is also growing, which could lead to major train accidents, including train derailments or collisions (Ning, 2024). When a train is on a bridge and subjected to severe wind and rain, the surrounding flow field experiences stronger fluctuations (Zhang et al., 2025b). Therefore, it is essential to conduct a thorough study of the flow field characteristics around the train on the bridge under wind–rain conditions to evaluate the operational safety of high-speed trains. In natural rainy conditions, the raindrop size distribution varies significantly with different rainfall intensities (Zhang et al., 2025a). Under varying rainfall intensities, raindrops of different sizes experi­ ence different aerodynamic effects (Singh et al., 2021). The main raindrop size distribution models currently used are the Best empirical distribution, the Marshall-Palmer (M-P) distribution, and the Gamma distribution (Lei et al., 2022). The motion of the raindrops is influenced by the wind-driven rain effect (Zhao, 2022). During the motion process, raindrops are influenced by the wind-driven rain effect. Under the ac­ tion of aerodynamic drag, the velocity of the raindrops gradually tends to become consistent with the surrounding flow field (Li et al., 2025). Some researchers have conducted wind tunnel tests on airfoils in rainy conditions (Bezos et al., 1992; Hansman and Craig, 1987). Other re­ searchers have investigated the aerodynamics of high-speed trains under wind-rain coupling via wind tunnel tests at different wind speeds, yaw angles, and rainfall intensities (Peng et al., 2021). The study de­ monstrated that rainfall significantly affects train aerodynamic loads, Peer review under the responsibility of Editorial Board of Advances in Wind Engineering. Corresponding author. E-mail address: 2766433600@qq.com (M. Dong). ⁎ https://doi.org/10.1016/j.awe.2025.100083 Received 1 August 2025; Received in revised form 23 October 2025; Accepted 31 October 2025 Available online 5 November 2025 2950-6018/© 2025 The Authors. Publishing services by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/). M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 influencing different coefficients in distinct patterns and to varying degrees across yaw angles. However, wind tunnel testing faces limita­ tions including high costs and difficulties in precise precipitation con­ trol. Consequently, numerical simulation has become the preferred method for investigating wind-rain two-phase flow aerodynamics. The commonly used methods for simulating two-phase flow are the Eulerian–Eulerian method, based on phase volume fraction, and the Eulerian–Lagrangian method, which creates discrete phase injection sources. The Eulerian–Eulerian method efficiently simulates overall rainfall without tracking individual raindrop trajectories, but cannot capture discrete raindrop motion or phenomena such as collision, splashing, and water film formation. Some researchers have used the Eulerian–Eulerian method to study the impact of the wind–rain cou­ pling effect on the aerodynamic characteristics of high-speed trains (Yue et al., 2016). Compared to pure crosswind, the wind–rain en­ vironment further reduces operational safety. Li et al. (2024c) analyzed the aerodynamic characteristics, wind–rain phase distribution, and flow field mechanisms during the train-passing process. The research in­ dicates that rainfall alters the pressure coefficient distribution on the train, and this phenomenon is particularly pronounced at the head and tail of the train. Ouyang et al. (2023) studied the flow field character­ istics of high-speed trains passing through tunnel entrances under strong wind–rain conditions. The study indicated that the rainfall phase increases the average wind–rain load and has differing effects on in­ dividual trains. During the passing process, the rain-induced load am­ plitude increases, further affecting the train's safety. The Eulerian–Lagrangian method combines the advantages of both the Eulerian and Lagrangian methods. It allows the overall flow field information to be obtained through Eulerian grids while capturing local details using Lagrangian particle tracking. This method provides more accurate results in simulating the complex process of rainfall. The Eulerian-Lagrangian method's precise raindrop trajectory tracking en­ abled its early application in wind-driven rain research. Wang et al. (2020) combined measurements and simulations to study typhoon flow fields on low-rise buildings. Huang et al. (2019) employed the M-P raindrop spectrum to analyze rain load distribution on large-span bridges, providing theoretical support for bridge design in extreme wind-rain environments. Subsequent applications to moving objects include several key studies. Wu and Cao (2017) investigated coupled raindrop icing and heavy rainfall effects on airfoils, finding 17 % maximum lift reduction from icing and 60 % drag increase from rain­ fall. Fatahian et al. (2020) proposed a DPM-VOF coupling method for airfoil water film simulation. Patel et al. (2022) used LES with La­ grangian particle tracking to examine vehicle-rain interactions. Raeesi et al. (2023) reported 11.7 % drag increase in rainy conditions, with tire splash contributing over 40 % to this effect. Some scholars have applied Eulerian–Lagrangian simulations to trains. Yu et al. (2021a,b, 2022) investigated train aerodynamic characteristics and safety in strong wind-rain environments using this method. Sheng et al. (2022, 2025a,b) developed an aerodynamic model based on the M-P raindrop spectrum, demonstrating altered forces and moments across train components due to rain loads. Sun and Du (2018) created a UDF for raindrop spectrum modeling, comparing three rainfall models and analyzing aerodynamic variations with rainfall intensity, crosswind, and train speed. Li et al. (2024a) used instantaneous rainfall intensity to study raindrop impacts and found that raindrop accumulation forms water films on train surfaces. The thickness and coverage of these films increase with rainfall duration, leading to higher surface roughness and friction coefficients. When the train operates on the bridge under wind and rain condi­ tions, the characteristics of the surrounding flow field are significantly degraded. Researchers explored the impact of wind–rain environments on the aerodynamic performance of intercity trains on elevated bridges (Zeng et al., 2023a,b). The study showed that the raindrop density on the train and bridge surfaces increases with rising wind speed and rainfall intensity. In the wind–rain environment, crosswind plays a dominant role, and the pressure coefficient on the train surface in­ creases with higher crosswind speed and rainfall intensity. Researchers (Zoumb et al., 2025) investigated the high-speed train–bridge system under wind–rain coupling and found that the effect of rainfall loads on the system response is non-negligible. Wang et al. (2023) established a mathematical model for train overturning under crosswind based on a bridge section and studied train safety under wind–rain coupling. Compared with strong wind alone, the critical overturning wind speeds on the windward and leeward sides decrease under wind–rain coupling, with a more significant decrease on the leeward side. The aforementioned scholars have studied the aerodynamic per­ formance of trains in wind and rain environments and achieved notable results. However, several issues remain unresolved. Most studies using the Eulerian–Eulerian approach have revealed the influence of wind–­ rain coupling on aerodynamic forces. Yet, due to the limitations of this method, it cannot accurately capture raindrop impingement, splashing, or the flow behavior of liquid films on the train surface. The liquid film, as a direct factor altering surface flow conditions, plays a key role in explaining the fundamental mechanisms of aerodynamic variation (Hu et al., 2024). In addition, although the Eulerian–Lagrangian method has been applied in train-related research, most studies have focused on open-track conditions. When trains operate on bridges, the bridge structure significantly alters the surrounding flow field and the wind–rain distribution, causing more complex flow separation and in­ terference effects. However, studies on the aerodynamic and liquid-film dynamic responses of the coupled train–bridge system under wind–rain conditions are still limited. In terms of research scope, existing work often examines only a single variable and does not systematically reveal the coupling mechanisms between train speed and rainfall intensity or their combined effects on liquid-phase distribution and aerodynamic behavior. To bridge the aforementioned research gap, this study develops a refined three-dimensional numerical model of the coupled train–bridge system based on the Eulerian–Lagrangian approach and the SST k–ω turbulence model. The primary objectives of this work are as follows: (1) To accurately capture the detailed behavior of two-phase wind–rain flow within the train–bridge coupled system under bridge en­ vironments, with particular emphasis on the formation and dis­ tribution of liquid films on the train surface. (2) To analyze the aerodynamic loads and surrounding flow-field characteristics of the train under various combinations of train speeds and rainfall intensities. (3) To elucidate the intrinsic relationship between liquid-film dynamics and variations in aerodynamic behavior, thereby providing a robust theoretical basis for evaluating the operational safety of trains on bridges under complex weather conditions. 2. Method 2.1. Geometrical model The three-train CRH2 high-speed train model used in this study is shown in Fig. 1. It has a length (L) of 76.4 m, a width (W) of 3.38 m, and a height (H) of 3.7 m. The bogie is simplified and the pantograph is excluded from this model (Chen et al., 2024) to improve the compu­ tational efficiency according to EN 14067–6 (2018). The bridge model is shown in Fig. 2. The model adopts the 32 m prestressed concrete double-track simply supported beam bridge specified in Tongqiao [2016] 2311-I of China Railway (2016). The width of the bridge deck is 13.4 m, the height from the bottom of the beam to the track bottom is 3.54 m, and the center-to-center distance between the tracks is 5 m. The disturbance induced by the bridge piers is primarily confined to the region beneath the bridge deck, while it exerts almost no influence on the flow field surrounding the train. In the calculation, the influence of the bridge piers and the track is neglected (Chen et al., 2024), and the 2 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 1. Train model (unit: m). ui =0 xi ui (1) 2u 1 p i +v + fi xi x j xj ui = xj (2) In the equation: ui represents the Reynolds-averaged velocity com­ ponents, ρ is the fluid density, p is the pressure, v is the fluid dynamic viscosity, and fi is the body force term. In order to close the RANS equations and accurately simulate the complex turbulent effects in the flow field, especially the flow separa­ tion near the wall, the SST k-ω (Menter, 1994) two-equation turbulence model proposed by Menter is selected. This model combines the ad­ vantages of the k-ω model in the near-wall region with the robustness of the k-ε model in the far-field region, achieving high precision. The raindrop size distribution in reality is non-homogeneous. In this study, the Best distribution (Lei, 2015) for raindrop sizes is adopted, in which the relationship of particle diameter can be expressed as: Fig. 2. Bridge model (unit: mm). track height is simulated with a 200 mm clearance between the train body and the ground. The train is fully situated on the bridge and oc­ cupies the right side of the bridge deck. This study investigates the aerodynamic characteristics and liquidphase distribution of trains on bridges under crosswind and rainfall conditions. The numerical simulations were performed using STARCCM+ software, employing the Eulerian-Lagrangian method coupled with the SST k-ω turbulence model. The simulation parameters include: 90° crosswind at 17.1 m/s (Grade 7 wind according to GB/T 28591–2012), with rainfall intensities of 100, 300, and 500 mm/h (Lei, 2015), plus a no-rain condition for comparison, at various train speeds. F (D ) = 1 exp (3) (4) a = ARp 2.2. Multiphase flow model DP n a In the equation, F(D) denotes the fraction of the total raindrop volume contributed by raindrops with diameters smaller than D. DP represents the raindrop diameter (mm). R is the rainfall intensity (mm/h). A and P are empirical constants, with A = 1.3, P = 0.232. In numerical simulations, the modal raindrop diameter—corresponding to the size with the largest number of raindrops under a given rainfall intensity—is typically selected as the representative raindrop diameter. This diameter can be expressed as: By simulating the actual rainfall environment, the EulerianLagrangian model treats air as the continuous phase and raindrop particles as the discrete phase. These two phases are coupled within the flow field and solved through numerical methods. The detailed simu­ lation procedure is illustrated in Fig. 3. This study employs a numerical simulation approach based on the Reynolds-Averaged Navier-Stokes (RANS) equations to calculate the three-dimensional, steady, incompressible turbulent flow in the ex­ ternal flow field around high-speed trains. The fundamental flow dy­ namics are described by the continuity and momentum equations, as presented below: DP = a 1 b 1 b b (5) In the equation, b is an empirical constant, with b = 2.25. According to the above formula, the raindrop diameters corresponding to rainfall rates of 100, 300, and 500 mm/h are 2.91, 3.76, and 4.23 mm, re­ spectively. When the raindrop falls and contacts the train body, the Bai-Gosman model (Bai and Gosman, 1995) is employed to predict the outcomes of raindrop impacts on the train surface or liquid film, as depicted in Fig. 4. In the simulation, this collision model is incorporated into the Lagrangian framework. When raindrops collide with the train surface, four types of phenomena—Adhere, Rebound, Spread, and Splash—occur, depending on the impact energy level. In addition, according to Li et al. (2024b), the maximum thickness of the liquid film formed on the automotive body Fig. 4. Bai-Gosman collision model: (a) Adhere, (b) Rebound, (c) Spread, (d) Break-up and Rebound, (e) Break-up and Spread, (f) Splash. Fig. 3. Simulation flow diagram. 3 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 5. Computational domain and boundary conditions. surface was set to 4.95 mm to maintain the physical parameters within conventional limits. velocities of the train and the crosswind were imposed in the positive xdirection and the positive y-direction, respectively. EFMN and AEND are pressure outlets. The top surface ABFE is a slip wall. To simulate the relative motion between the train and the bridge and ground, the bottom surface CDNM and bridge were defined as no-slip moving wall with the train speed in the opposite direction. The rainfall plane and its position are shown in Fig. 6. A densesparse region configuration was adopted, with a raindrop-refinement region set around the train body. Under different working conditions, the position of the refinement region was adjusted to ensure that raindrops fully covered the train body and the surrounding flow field. A sparse region was defined in the area farther from the train. The number of raindrop injection points in the refinement region was 80,000, while in the sparse region it was 40,000. For the discrete phase (raindrops), the train surface was modeled using the Bai-Gosman col­ lision model, where physical phenomena such as splashing, rebounding, and water film formation occur when raindrops collide with the train body. The outer surfaces of the computational domain and the bridge were treated as "escape" boundaries, where raindrops are considered to exit the domain upon contact and computation is terminated. 2.3. Grid and boundary The computational domain is set according to the guidelines in Railway Aerodynamics, Part 4 – Train Aerodynamic Performance Simulation Specifications (TB/T 3503.4-2018, 2018) to allow the full development of the flow field and to minimize the impact of boundaries. As shown in Fig. 5, the computational domain was defined with a width of 50H and a height of 20H, where H denotes the train height. The upstream distance from the velocity inlet to the front of the train was set to 100H, while the downstream distance from the pressure outlet to the rear of the train was set to 80H. The vertical distance from the bottom surface of the bridge to the domain boundary of the computational domain was specified as 10 m. The computational domain was meshed using the trimmed mesh method. To accurately capture the aerodynamic features around the train, four locally refined mesh regions were applied in areas with substantial flow variation, including the vicinity of the train body, the wake region, and the leeward side. The specific mesh dimensions are provided in Table 1. The train surface boundary layer was modeled with six layers, and the bridge surface with four layers, using a layer thickness growth rate of 1.2. The walladjacent mesh was configured to maintain y⁺ values below 60, and a high-y⁺ wall function approach was adopted. For the remaining surfaces in the computational domain, no boundary layer was applied. The total number of cells in the computational domain reached approximately 29.67 million. As shown in Fig. 5, for the continuous phase (air), the train and bridge surfaces were modeled as smooth surfaces to reduce computational cost and enhance numerical stability. ABCD and BFMC are velocity inlets, where the 3. Validation and verification of the numerical model 3.1. Aerodynamic force coefficients The aerodynamic force of the train is determined according to EN 14067–4 (2013), to facilitate comparison with wind tunnel test results. The drag coefficient CD , lateral force coefficient CS , and lift coeffi­ cient CL are defined as follows: Table 1 Grid dimensions (unit: m). External area Bridge Train body Bogie and windshield Encryption block 1 Encryption block 2 Encryption block 3 Encryption block 4 Minimum dimension Minimum dimension Prismatic layer thickness 1.44 0.1 0.1 0.05 0.09 0.18 0.36 0.72 1.44 0.02 0.01 0.01 0.09 0.18 0.36 0.72 / 0.0073 0.0073 0.0073 - 4 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 6. Rainfall plane. tests and numerical simulations. As shown in Fig. 8, the numerical si­ mulation results closely align with the wind tunnel test results, with the maximum relative error between the two remaining within 10 %. This suggests that the turbulence model selected for this study is appro­ priate, and the computed results are highly reliable. 3.3. Independence study To study the influences of different turbulence models on the si­ mulation results, the Standard k-ε, Spalart–Allmaras, and SST k-ω tur­ bulence models were compared by the simulations of the train running at 250 km/h under crosswind and a rainfall intensity of 500 mm/h. The key aerodynamic coefficients obtained by each model are presented in Fig. 9. The discrepancies among different turbulence models are less than 5 %, indicating that the SST k-ω model is suitable for use in this research. To evaluate the effects of grid number and particle count variations on the numerical simulation results, five grid schemes were established under conditions of 500 mm/h rainfall intensity and a train speed of 250 km/h, as detailed in Table 2. The evaluation was conducted by comparing the aerodynamic force coefficients of the leading car, the maximum liquid film flow velocity on the train surface, and the max­ imum raindrop liquid volume fraction (LVF) in the surrounding flow field. The convergence behavior is illustrated in Fig. 10. The data in­ dicate that with increasing grid resolution and raindrop number, the force coefficients and rainfall parameters exhibit only minor fluctua­ tions. These results confirm the convergence of the simulation with respect to raindrop count. Considering computational costs, Mesh 3 was selected as the final simulation scheme. In addition to conducting independence validations for the turbu­ lence model, grid, and particle count, the independence of the liquidfilm parameters was also examined. A sensitivity analysis was per­ formed by comparing three maximum liquid-film thicknesses (0.00295 mm, 0.00495 mm, and 0.00695 mm) under conditions of 500 mm/h rainfall intensity and a train speed of 250 km/h, as Fig. 7. Wind tunnel test model. CD = CS = CL = Cx 0.5 U 2S (6) Cy (7) 0.5 U 2S Cz 0.5 U 2S (8) 3 In the equations, is the air density; = 1.225 kg/m ; Cx, Cy, and Cz represent the drag force, lateral force, and lift force, respectively; S is the train's frontal projected area; and U is the relative velocity. 3.2. Validation with wind tunnel test of the train To verify the reliability of the numerical method used, a comparison of the numerical simulation results with the wind tunnel test data (Zhang et al., 2018) was conducted. The wind tunnel test model is shown in Fig. 7. Fig. 8 presents a comparison of CL and CD values of the head car at different wind direction angles, obtained from wind-tunnel Fig. 8. Comparisons of the numerical simulation and wind tunnel test (Zhang et al., 2018). 5 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 9. Aerodynamic coefficients predicted by different turbulence models. Table 2 Grid and particle schemes. Mesh 1 Mesh 2 Mesh 3 Mesh 4 Mesh 5 Fig. 11. Liquid film thickness independence curve. Number of Grid Cells Number of Particles (dense coverage/sparse coverage) 12.79 million 29.67 million 29.67 million 29.67 million 44.81 million (80,000/40,000) (20,000/10,000) (80,000/40,000) (240,000/160,000) (80,000/40,000) obviously on the windward side of the train and dispersing on the leeward side. As rainfall intensity increases, the distribution patterns around the train remain consistent. Raindrop impingements under crosswind focus on the front part of the head car and the windward side. When striking these windward surfaces, raindrops undergo two distinct separation stages. The first-stage separation occurs immediately upon impact, with droplets rapidly ejected due to surface impingement. The second-stage separation results from crosswind-induced instability of the adhering water film, eventually causing boundary layer detach­ ment on the leeward side. The domain around the train was divided into three zones (Z1, Z2, Z3) based on LVF gradients. After raindrop impingement, a thin accu­ mulation band formed at the train bottom and extended leeward across the roof, marking the Z1-Z2 boundary. A distinct secondary accumula­ tion band separated at the windward upper corner, adhering to the roof before extending leeward to the ground, delineating Z3 from Z2. Fig. 12 shows Z2 contains the highest raindrop accumulation, while Z3 shows negligible LVF, defining a "rain-free zone". A key spatial trend is that Z1 maintains a constant cross-sectional area along the train length. On the other hand, the LVF increases rearward, primarily due to raindrop ac­ cumulation at the tail car. Z2 shows a decreasing cross-sectional area but progressively increasing LVF, indicating enhanced leeward accu­ mulation at the tail car. Z3 expands dramatically from head to tail, maintaining near-zero LVF due to crosswind-driven droplet detachment on the leeward side. With increasing rainfall intensity, LVF in Z1 and Z2 increases, showing enhanced raindrop accumulation. Maximum LVF rose from 1.54 × 10⁻⁴ at 100 mm/h to 8.47 × 10⁻⁴ at 500 mm/h, a 450 % increase. The "rain-free zone" Z3 remains consistent across rainfall intensities. To examine the effects of the train speed on raindrop distribution, Fig. 13 presents the LVF distributions at 500 mm/h for train speeds of 250 km/h, 300 km/h, and 350 km/h. While raindrop distribution illustrated in Fig. 11. The results demonstrate that variations in liquidfilm thickness have a negligible influence on the simulation outcomes. Based on relevant literature and the validation findings, a liquid-film thickness of 0.00495 mm was ultimately selected for the simulations. 4. Results and discussions 4.1. Liquid flow dynamics of raindrops 4.1.1. Raindrops around the train There is a mutual interaction between rainfall and the flow field. When a train runs in rainy weather, the surrounding flow field strongly influences raindrop trajectories, leading to a highly non-uniform rain­ drop distribution. Rain affects both droplet impact and detachment on the train surface and modifies the flow field through droplet accumu­ lation and splashing. This section examines how crosswind influences raindrop volume fraction under varying rainfall intensities and train speeds. Fig. 12 shows liquid volume fraction on three streamwise crosssections (located in the head car, middle car, and tail car, respectively) and on the horizontal plane cross-section at a train speed of 350 km/h with different rainfall intensities. Crosswind significantly affects rain­ drop distributions. The raindrops deflect markedly, accumulating Fig. 10. Grid and particle count independence curves. 6 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 12. Liquid volume fraction around the train at different rainfall intensities: (a) 100 mm/h, (b) 300 mm/h, (c) 500 mm/h. Fig. 13. Liquid volume fraction around the train at different train speeds: (a) 250 km/h, (b) 300 km/h, (c) 350 km/h. patterns remain consistent at different speeds, the maximum LVF in Z2 decreases from 6.36 × 10⁻⁴ (250 km/h) to 4.78 × 10⁻⁴ (350 km/h), re­ presenting a 24.9 % reduction. Cross-sectional analysis reveals nar­ rowing of the "rain-free zone" Z3. With the increase of train speed, the angle between the boundary of Z3 and the leeward side of the train contracts from 12.24° to 11.17° and further to 9.43° at corresponding speeds. Generally, in contrast to rainfall intensity, train speed pre­ dominantly influences leeward rain-free zone (Z3) morphology rather than the LVF magnitude. Overall, rainfall intensity directly affects the liquid phase distribution by altering the LVF in the flow around the train, whereas train speed has a relatively smaller impact on the LVF itself and primarily influences the liquid phase distribution by affecting the surrounding flow field. Based on Figs. 12 and 13, the quantitative analysis of the maximum LVF around the train is presented in Table 3. Under a constant train speed, the maximum LVF increases markedly with increasing rainfall intensity. At a speed of 350 km/h, when the rainfall intensity rises from 100 mm/h to 500 mm/h, the maximum LVF increases from 0.000532 to 0.00183—an increase exceeding 243.9 %. This directly indicates the growth in raindrop number density per unit volume. Under the same rainfall intensity, the maximum LVF generally rises with increasing train speed, a trend that becomes more evident under moderate and heavy rainfall conditions (300 and 500 mm/h). This suggests that higher train speeds enhance the coupling between airflow and rain­ drops, causing more raindrops to accumulate in critical regions such as the train head. In summary, both stronger rainfall and higher train speeds jointly contribute to a substantial increase in raindrop con­ centration around the train, thereby intensifying raindrop impact and local accumulation on the train surface. 4.1.2. Liquid film flow on the train The wall film on the train surface was formed and impacted by the aerodynamic shear forces. Liquid film separation occurs when local thickness reaches a critical value or when the film encounters geome­ trically discontinuous regions. This section investigates the effect of crosswinds on liquid film thickness at different rainfall intensities and train speeds. Fig. 14 presents liquid film thickness distributions on the head car, roof, and tail car at different rainfall intensities when the train runs at 350 km/h in crosswind. At the train nose, intense raindrop impact and high-speed airflow shear forces caused ultrashort raindrop contact time, resulting in splash-dominated patterns rather than con­ tinuous liquid film formation. Consequently, liquid film thickness ap­ proaches zero in this region. Striated accumulations inclined from the top to bottom corner of the head car formed due to crosswind. These accumulations focused on the leeward side of the cab window and thickened with increasing rainfall intensity. Liquid film formed at the head flowed rearward along the roof, coalescing on the windward side and interrupting at inter-car gaps. With increasing rainfall intensity, liquid film coverage expanded across more surface areas, reaching maximum coverage on the head car at 500 mm/h. At the tail car, raindrop accumulation formed thicker liquid films around the cab window region, where maximum film thickness occurred due to enhanced water accumulation from flow separation. Fig. 15 illustrates liquid film thickness on windward and leeward sur­ faces at different rainfall intensities. On the windward side, striated accumulation patterns remained consistent across rainfall intensities, progressively thickening from head to tail. Increased rainfall intensity thickened the striated film in the head and middle cars but thinned it in the tail car, indicating weakened raindrop accumulation due to en­ hanced flow separation. Conversely, leeward side distributions showed opposite patterns in which thickened films dominated the head and middle cars, while tail car accumulation weakened relative to the Table 3 Maximum LVF around the train. Train speeds (km/h) 250 300 350 Rainfall intensities (mm/h) 100 300 500 0.000421 0.000492 0.000532 0.00113 0.00135 0.00162 0.00119 0.00135 0.00183 7 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 14. Liquid film thickness on the train at different rainfall intensities: (a) 100 mm/h, (b) 300 mm/h, (c) 500 mm/h. Fig. 15. Liquid film thickness on the windward and leeward sides of the train at different rainfall intensities: (a) 100 mm/h, (b) 300 mm/h, (c) 500 mm/h. windward side. Higher rainfall intensities thickened the leeward stri­ ated film and enhanced accumulation in the tail car. Variation of the running speed alters the flow around the train, thus affecting surface liquid distribution. Fig. 16 shows liquid film thickness on the head car, tail car, and roof surfaces at 500 mm/h rainfall in crosswinds at different train speeds. The thickness of the liquid film on the head car and the roof gradually increases with train speed while the striated accumula­ tion patterns remain consistent. Compared with Fig. 12, the influences of train speed are less pronounced than those of rainfall intensity. Fig. 17 displays the windward and leeward side film thickness at 500 mm/h rainfall under different train speeds. Windward raindrop accumulation pre­ dominated on the middle/tail cars. An increase in train speed to 300 km/h induced film coalescence and thickening on the middle car versus dispersion and thinning on the tail car. At 350 km/h, this trend reversed, with middle car films thinning while tail car zones exhibited localized thickening. Lee­ ward striated accumulation exhibited speed-invariant persistence on the head and the middle cars, while film thickness grew with train speed. Lo­ cally thickened films developed in the middle of the tail car due to focused raindrop accumulation. The flow of the liquid film on the surface of the train exhibits sig­ nificant variation at different rainfall intensities and train speeds. Figs. 18 and 19 compare the influences of the rainfall intensity and train speed on the velocity distributions of the liquid film on both windward and leeward sides of the train, respectively. In Fig. 18, the distribution of liquid film velocity on the train surface at different rainfall intensities when the train speed is 350 km/h is displayed. As shown in Fig. 18(c), raindrops striking the front part and windward side surface of the train lead to the formation of liquid film with discontinuous velocity dis­ tribution resembling dashed lines. On the windward side, band-shaped high-speed liquid film formed on the middle and rear parts of the train. With increasing rainfall intensity, the overall film velocity on the windward side increases. At 100 mm/h, a single high-speed band ap­ pears on the middle car while at 500 mm/h, this develops into two distinct high-speed bands. Owing to the contraction of the cross-sec­ tional area in the streamlined part of the tail, a lower-velocity liquid film formed. The magnitude increases and then decreases with in­ creasing rainfall intensity. Combined with the analysis of Fig. 14, it is evident that areas with thicker liquid film correspond directly to zones of higher velocity. Thicker liquid film represents accumulation of raindrops. To stabilize the formed thicker film, liquid tends to flow into it and more high-velocity film will emerge in this area. In contrast, the leeward side of the train, influenced by Z3 in Fig. 12, was generally shielded from direct raindrop impact, resulting in a more uniform liquid film velocity distribution. Liquid film with velocity approaching zero formed from the middle of the head car to the inter-car gap. Although velocity rose slightly on the middle and tail cars, it remained low Fig. 16. Liquid film thickness on the train at different train speeds: (a) 250 km/h, (b) 300 km/h, (c) 350 km/h. Fig. 17. Liquid film thickness on the windward and leeward sides of the train at different train speeds: (a) 250 km/h, (b) 300 km/h, (c) 350 km/h. 8 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 18. Liquid film velocity on the train at different rainfall intensities: (a) 100 mm/h, (b) 300 mm/h, (c) 500 mm/h. Fig. 19. Liquid film velocity on the train at different train speeds: (a) 250 km/h, (b) 300 km/h, (c) 350 km/h. dependent variation. On the leeward side, however, velocity gradients of the liquid film on the head car are more sensitive to train speed. Velocity magnitude of the dotted liquid film increases with train speed. Overall, the liquid film velocity on the train surface is jointly affected by rainfall intensity and the surrounding airflow. Rainfall intensity predominantly influences the windward side, while train speed has a greater effect on the leeward side. Quantitative data on the maximum liquid-film flow velocity on the train surface are presented in Table 4. The results indicate that the film velocity increases with both train speed and rainfall intensity. At a speed of 250 km/ h, the maximum film velocity rises from 7.14 m/s at a rainfall intensity of 100 mm/h to 15.25 m/s at 500 mm/h, representing an increase of 113.59 %. Under a rainfall intensity of 500 mm/h, when the train speed increases from 250 km/h to 350 km/h, the maximum film velocity further surges from 15.25 m/s to 21.84 m/s, corresponding to a 43.21 % increase. The higher train speed generates stronger aerodynamic shear forces that directly accelerate the liquid-film flow, while greater rainfall intensity provides a larger liquid supply, promoting the formation of thicker films and consequently higher flow velocities. Such high-speed liquid-film motion may intensify surface erosion and potentially compromise the stability of the train. Table 4 Maximum film velocity on train surface (unit: m/s). Train speeds (km/h) 250 300 350 Rainfall intensities (mm/h) 100 300 500 7.14 9.96 12.96 9.39 16.71 17.10 15.25 18.83 21.84 overall. Compared to the windward side of the train, rainfall intensity has only subtle influences on the leeward side. However, two variations were observed: rainfall-dependent increases that the velocity gradients on the head car, and the velocity of dotted liquid films on the tail formed by raindrop impacts. Fig. 19 shows the distribution of liquid film velocity at different train speeds under a fixed rainfall intensity of 500 mm/h. The overall pattern resembles that in Fig. 18. As train speed increases, liquid film velocity on the windward side rises significantly. This is because a faster train increases the frequency and energy of raindrop impacts. On the leeward side, faster train speeds enhance the surrounding airflow, leading to a gradual increase in film velocity, though still considerably lower than on the windward side. On the windward side, variations in film velocity due to train speed are smaller than those caused by rainfall intensity. The aerodynamic response to train speed manifests in liquid film dynamics. Train speed primarily influences the liquid film in two positions on the train: the banded high-speed films on the middle and tail cars, and the low-speed film on the streamlined part of the tail. As train speed increases, both underwent acceleration. Notably, at 350 km/h, the banded high-speed film separates into two distinct bands, a phenomenon analogous to rainfall intensity- 4.2. Aerodynamic characteristics of the train 4.2.1. Aerodynamic forces When the train speed is constant, variations in rainfall intensity influence the aerodynamic forces acting on the train. Fig. 20 compares the aerodynamic forces at the train speed of 350 km/h under different rainfall intensities. At a train speed of 350 km/h, the effects of rain-free condition and varying rainfall intensities on the side forces (Fy), lift (Fz), and drag (Fx) on the head, middle, and tail cars differ. Raindrop impacts Fig. 20. Variation of aerodynamic forces with different rainfall intensities at the train speed of 350 km/h: (a) head car, (b) middle car, (c) tail car. 9 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Table 5 Aerodynamic force comparison. This study Literature (Gong et al., 2025) Train speed / (km/h) Wind speed / (m/s) Fy / kN Fz / kN 350 350 17.2 12 54.05 49.82 29.17 19.50 Fig. 21. Variation of aerodynamic forces with different train speed at 500 mm/h rainfall: (a) head car, (b) middle car, (c) tail car. maximum pressure increases from 3559.3 Pa (rain-free) to 4169.1 Pa (500 mm/h), a 17.13 % rise. At 300 km/h, the maximum pressure in­ creases from 4630.6 Pa to 5573.6 Pa (a 20.36 % rise), while at 350 km/ h the maximum pressure increases from 6009.1 Pa to 7417.3 Pa (a 23.43 % rise). These results demonstrate an amplified effect induced by rainfall on nose pressure with increasing train speed. Flow separation leads to a pronounced negative pressure region in the wake of the train. Fig. 23 presents streamwise pressure distributions in the wake in varying conditions. A distinct low-pressure region emerges in the wake, with the negative pressure zone progressively expanding with the increased train speed due to intensified flow separation at the tail. The negative pressure zone also attenuates with increasing rainfall intensity. Due to the interaction between the airflow and raindrops, rainfall reduces ne­ gative pressure magnitudes on the leeward side and the wake region. Cor­ respondingly, the surrounding flow field alters the trajectories of raindrops, with aerodynamic drag accelerating raindrops toward local airflow velocity. Larger velocity differentials produce greater drag forces exerted on rain­ drops. Simultaneously, raindrops act as discrete mass points in the flow field, exerting significant counter-drag in the air. This momentum exchange decelerates the airflow around the train. Raindrops detaching from the train initially exhibit low velocity but are rapidly accelerated by aerodynamic drag. The most pronounced raindrop detachments occur in the wake. Conversely, minimal raindrop movement occurs in the rain-free zone ad­ jacent to the tail, where the flow field remains unchanged. Therefore, compared to the rain-free condition, the flow field velocity in rainfall con­ ditions decreases, resulting in a lower negative pressure peak. on the train nose and windward surfaces result in increased side forces and drag for the head, middle, and tail cars as the rainfall intensity increases. Compared to the rain-free condition, both drag and side forces for the head, middle and tail cars increase, with this effect be­ coming more pronounced as rainfall intensity increases. As shown in the liquid film analysis in Fig. 14, the overall film thickness increases, and the downward impact of raindrops contributes to a reduction in lift with higher rainfall intensity. The lift of the head, middle, and tail cars decreases in the rain and continues to decline as rainfall intensity in­ creased. Comparing the aerodynamic forces of the head car in rain-free condition and 500 mm/h rainfall, the side force increases by 1.61 %, drag increases by 31.27 %, and lift decreases by 4.88 %. To ensure the accuracy of the results, the train's lateral and lift forces calculated for the pure-wind condition at a speed of 350 km/h were compared with the simulation results reported in the literature (Gong et al., 2025). As shown in Table 5, the aerodynamic forces obtained in this study agree well with the published results in both magnitude and trend. This comparison confirms the reliability of the present numerical model for aerodynamic simulations under pure-wind conditions. Under the constant rainfall intensity, train speed is the governing factor for aerodynamic forces. Fig. 21 compares the side forces, lift forces, and drag forces acting on the head, middle, and tail cars at different train speeds under a constant rainfall intensity of 500 mm/h. As the train speed in­ creases, the airflow and raindrop impacts on the windward side of the head car intensify, leading to progressively greater drag and side forces on the head car. The lift on the head car decreases as speed increases. For the middle car, both drag and lift increases with train speed, while the side force decreases. For the tail car, the side force is significantly smaller than that of the head and middle cars and decreases as train speed increases. Drag in­ creases with train speed, while lift initially increases and then decreases as train speed increases. 4.3. Characteristics of the flow around the train Fig. 24 illustrates the configuration of probe points around the train according to the specifications in EN 14067–4 (2013). On both the wind­ ward and leeward sides of the train, three sets of probe points (L1–3, R1–3) are placed 2.5 m from the center of the rail, at heights of 0.5 m, 1.5 m, and 3.0 m above the bridge deck. 2000 probe points for each position are placed 40 m in front of and 60 m behind the train along the train running direction. The spacing between adjacent points is 0.0882 m. 4.2.2. Pressure distributions on the head The nose region of the head car experiences the most intense aerodynamic loads and dynamic raindrop impacts during the highspeed train operation, being the initial contact zone for airflow and raindrops. Fig. 22 compares the surface pressure on the train nose under varying train speeds and rainfall intensities. The positive pressure zone near the nose's windward side expands and extends further windward with increasing rainfall intensity. A detailed comparison between the maximum nose pressure in rain-free and 500 mm/h rainfall conditions reveals progressive pressure enhancements. At 250 km/h, the 4.3.1. Velocity distributions Rainfall influences the velocity distributions of the flow field around the train. Figs. 25 and 26 present the influences of rainfall intensity and train speed on the velocity of the probe points, respectively. The results are nondimensionalized by U/U∞. 10 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 22. Pressure distributions on the head car at different rainfall intensities: (a) 0 mm/h, (b) 100 mm/h, (c) 300 mm/h, (d) 500 mm/h. Fig. 23. Pressure distributions in the wake at different rainfall intensities: (a) 0 mm/h, (b) 100 mm/h, (c) 300 mm/h, (d) 500 mm/h. The overall velocity distribution exhibits a similar trend in different conditions. Taking the case of the train running at 350 km/h under a rainfall intensity of 500 mm/h as an example, on the windward side of the train, the incoming flow velocity decreases sharply at the nose of the train (x = 0 m), forming a local minimum. This minimum becomes less pronounced with increasing height. Subsequently, the velocity gradually increases at the cab window of the head car, recovering to­ ward the free-stream velocity and forming the first local maximum. This peak is most prominent at location R1 and becomes progressively less distinct at R2 and R3. At the rear end of the train (x = 76.4 m), due to the sudden discontinuity of the streamlined tail, a second velocity peak appears. In the wake region after the train, the flow gradually recovers to the incoming velocity. On the leeward side of the train, the incoming flow velocity rises sharply at the train nose (x = 0 m), forming an initial velocity peak. This is followed by a rapid decrease in velocity, with a general downward trend observed along the train body (0 m < x < 76.4 m). At location L1, the velocity distribution is notably irre­ gular, with fluctuations along the train body. As the height increases, the velocity profiles become progressively smoother. Similar to the windward side, at the rear part of the train, the flow velocity of the Fig. 24. Measurement points around the train. 11 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 25. Comparison of probe-point velocity distributions along the train at different rainfall intensities. probe points increases again before gradually recovering to the freestream velocity. In Fig. 25, it can be observed that the impact of rainfall intensity on the windward side flow field is minimal, with the velocity distribution remaining almost unchanged. The most pronounced influences induced by rainfall occur in the rear part of L1 and the front parts of L2 and L3, as shown in the enlarged area in Fig. 25. In Fig. 26, on the windward side of the train (R1, R2, R3), the velocity in front of the train (x < 0 m) and in the wake region (x > 76 m) decreases as the train speed increases. As the probe points approach the front of the train, the velocity drops sharply, reaching the minimum at the nose. At R1, the maximum ve­ locity around the head increases with the train speed while that de­ creases around the tail. Afterward, the velocity gradually recovers in the transition section of the train body. As shown in Fig. 26, the fluc­ tuations of the velocity attenuate with the increase of the train speed. On the leeward side of the train (L1, L2, L3), as the train speed increases, the maximum and minimum velocity at the train's head and tail de­ crease. Moreover, in the wake region (x > 76.4 m), higher train speed results in a longer distance required for the local velocity to recover to the free-stream velocity. Fig. 26. Comparison of probe-point velocity distributions along the train at different train speeds. 12 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 27. Probe-point pressure coefficient distributions under varying rainfall intensities around the train. Fig. 28. Probe-point pressure coefficient distributions under varying train speeds around the train. 4.3.2. Pressure distributions Figs. 27 and 28 present the influences of rainfall intensity and train speed on pressure distributions of the probe points, respectively. Ac­ cording to Bernoulli's principle, the pressure distributions exhibit op­ posite trends to the velocity distributions. Taking the case of the train running at 350 km/h with a rainfall intensity of 500 mm/h as an ex­ ample, on the windward side of the train, raindrops and air impact the nose of the head car, causing a rapid rise in pressure and the formation of a pronounced positive pressure peak (x = 0 m), followed by a smaller negative pressure peak. Additionally, at R3, the peak is noticeably lower than at R1 and R2. As the air flows along the train body, the pressure gradually decreases at the surrounding probe points. When the air reaches and leaves the train tail, the pressure drops sharply again, re­ sulting in a prominent negative pressure peak. This is followed by a secondary, smaller positive pressure peak in the train's wake region (x > 76.4 m), before finally stabilizing back to the ambient pressure. On the leeward side of the train, the pressure distribution is different from that on the windward side. A smaller positive pressure peak (x = 0 m) is first formed at the probe points around the head of the train, followed by a sharp decrease with a larger negative pressure 13 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Fig. 29. Turbulent kinetic energy (TKE) distributions at probe points under varying rainfall intensities around the train. Fig. 30. Turbulent kinetic energy (TKE) distributions at probe points under varying train speeds around the train. peak. The difference between positive and negative pressure peaks narrows as the height increases. Significant pressure fluctuations occur around the train and attenuate as the height increases. The pressure rises sharply around the rear part of the train and recovers to the am­ bient pressure in the wake. In Fig. 27, at different rainfall intensities, the trends on the wind­ ward side and leeward side are generally consistent. On the leeward side, the impact of rainfall intensity on the pressure coefficient is more significant around the body and in the wake region. As shown in the enlarged area in Fig. 27, the negative pressure peak is significantly lower in rain-free condition than in the rainy conditions. In Fig. 28, on the windward side around the train nose, the pressure fluctuation is most significant at 250 km/h. The average pressure along the train body decreases with train speed. On the leeward side, the maximum positive pressure around the nose and the average pressure along the train body increase with train speed. 4.3.3. TKE distributions Figs. 29 and 30 present the influences of rainfall intensity and train speed on turbulence kinetic energy (TKE) distributions of the probe 14 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 points, respectively. The TKE data has been nondimensionalized by TKE/(U∞)2. As a key parameter of turbulence intensity, the spatial distributions and evolutionary patterns of TKE provide important in­ sights into understanding the complex flow around the train. On the windward side of the train, TKE distributions vary with the height of probe points. Two peaks are formed around the head and in the wake at R1. TKE rises become less significant with increasing height. Only a small peak is noticed around the head at R2 and the TKE at R3 shows no significant variation. On the leeward side of the train, TKE increases sharply around the nose of the train at L1, forming the first peak. It then decreases rapidly and fluctuates along the train body. TKE rises slightly in the wake before ultimately diminishing to zero at a greater distance from the train. The intensity of TKE on the leeward side also decreases with height. At L2, the first peak becomes less discernible, with a gen­ erally lower TKE value. At L3, the first peak is no longer noticeable, and TKE fluctuates around the tail and further diminishes. In Fig. 29, on the windward side, the variation trends of different rainfall intensities are consistent. In the enlarged area on the left side of L1, in rainy conditions, the peak points are slightly delayed compared to rain-free conditions. At L2, the effect of different rainfall intensities on TKE is mainly concentrated around the head car. In the enlarged area locations of L2, the TKE peak at the rainfall intensity of 500 mm/h is much higher than in other conditions. At L3, TKE in the wake is smaller in rainy conditions than in rain-free conditions. In Fig. 30, on the windward side at R1, the peak values decrease with the increase of train speed. On the leeward side, different train speeds exhibit similar pat­ terns and TKE decreases with the increase of train speed. negligible effects on windward surfaces but significantly affects the leeward flow, particularly around the head car and in the wake. Train speed predominantly influences the overall distribution of flow velocity, pressure and TKE. On the leeward side, the fluctua­ tions in the flow around the train attenuate in both magnitude and complexity with increasing probe height. CRediT authorship contribution statement Mingwei Dong: Writing – review & editing, Writing – original draft, Visualization, Validation, Software, Methodology. Rui Li: Writing – review & editing, Methodology, Funding acquisition. Jianlin Xu: Visualization, Supervision. Yongxing Jia: Formal analysis. Yonggang Yang: Validation. Tao Zhao: Resources. Jiahui Chen: Resources, Data curation. Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influ­ ence the work reported in this paper. Acknowledgements This study was supported by the Gansu Provincial Science and Technology Department (Grant No. 22JR11RA150). References 5. Conclusions Bai, C., Gosman, A.D., 1995. Development of methodology for spray impingement si­ mulation. Sae Transactions 1. https://doi.org/10.4271/950283 Bezos, G.M., Dunham Jr., R.E., Gentry Jr., G.L., Melson Jr., W.E., 1992. Wind tunnel aerodynamic characteristics of a transport-type airfoil in a simulated heavy rain environment. NASA Langley Research Center, Hampton, VA, United States. https:// ntrs.nasa.gov/citations/19920022288. Chen, J.H., Li, R., Xu, J.L., Li, P., Zhao, W.H., Zheng, P.J., Jin, K.L., 2024. Study on the aerodynamic performances and the operational safety of the vehicle-bridge system under the crosswind. Mechanics Based Design of Structures and Machines 52, 7962–7984. https://doi.org/10.1080/15397734.2024.2313604 China Railway, 2016. Track precast ballastless track post-tensioned prestressed concrete simply supported box girder for high-speed railway with a design speed of 350 km/h (single line) - span 31.5 m. Tongqiao [2016] 2311-I, China Railway Corporation Construction Document No. [2016] 135. (in Chinese). EN 14067-4, 2013. Railway applications - Aerodynamics - Part 4: Requirements and test procedures for aerodynamics on open track. EN 14067-6, 2018. Railway applications - Aerodynamics - Part 6: Requirements and test procedures for cross wind assessment. Fatahian, H., Salarian, H., Nimvari, M.E., Khaleghinia, J., 2020. Numerical simulation of the effect of rain on aerodynamic performance and aeroacoustic mechanism of an airfoil via a two-phase flow approach. SN Applied Sciences 2, 867. https://doi.org/ 10.1007/s42452-020-2685-4 Gong, K., Bian, W.J., Liu, L.Y., Sun, L.X., Qin, J.L., Lou, J.L., 2025. Operational safety analysis of high-speed trains at 350 km/h and above under crosswind conditions. Journal of Beijing Jiaotong University 49, 167–173. https://doi.org/10.11860/j.issn. 1673-0291.20240035. (in Chinese). Hansman Jr, R.J., Craig, A.P., 1987. Low Reynolds number tests of NACA 64-210, NACA 0012, and Wortmann FX67-K170 airfoils in rain. Journal of Aircraft 24, 559–566. https://doi.org/10.2514/3.45476 Hu, X.J., Liu, L.H., Wang, J.Y., Guo, P., Hang, Z.H., Xin, L., 2024. Aerodynamic char­ acteristics and liquid film movement morphology of the DrivAer model in rainfall environments. Physics of Fluids 36, 123326. https://doi.org/10.1063/5.0237651 Huang, S.H., Li, Q.S., Liu, M., Chen, F.B., Liu, S., 2019. Numerical simulation of winddriven rain on a long-span bridge. International Journal of Structural Stability and Dynamics 19, 1950149. https://doi.org/10.1142/S0219455419501499 Lei, X., 2015. Study about wind (rain) effects and vibration control of flexible structural members in long-span bridge. Hunan University, China. (in Chinese). Lei, X., Shen, L., Chen, Z.Q., Niu, W.H., Wei, C.L., Zhang, X.W., 2022. Experimental analysis of additional aerodynamic effects caused by wind-driven rain on bridge main girder. Journal of Central South University 29, 2743–2756. https://doi.org/10.1007/ s11771-022-5115-5 Li, Z.X., Bian, R.F., Zhang, L., Chen, B., 2025. Wind-driven rain on low-rise gable-roof buildings considering interference effects. Journal of Building Engineering 105, 112501. https://doi.org/10.1016/j.jobe.2025.112501 Li, R., Chen, J.H., Li, P., 2024c. Research on influences of wind barriers on aerodynamic characteristics of train−bridge system in crosswind. Journal of Central South University (Science and Technology) 55, 3982–3997. https://doi.org/10.11817/j. issn.1672-7207.2024.10.030. (in Chinese). In this paper, Eulerian–Lagrangian approach was applied to study the influences of rainfall intensity and train speed on the liquid flow characteristics and aerodynamic performances of the train running on a bridge in the crosswind. The main conclusions are as follows: (1) In rainy conditions, rainfall intensity dominates liquid film dis­ tribution on the train, while train speed indirectly influences the dynamics of liquid film by affecting the flow field around the train. (2) The spatial distribution of raindrop volume fraction exhibits sig­ nificant discontinuity. At a train speed of 350 km/h, the maximum LVF around the train increased by 243.9 % when the rainfall in­ tensity rose from 100 mm/h to 500 mm/h. The liquid film thickness increases with both rainfall intensity and train speed. The flow velocity of the liquid film is affected by both rainfall and train speed. The increase in train speed from 250 to 350 km/h under a rainfall intensity of 500 mm/h resulted in a 43.21 % rise in the maximum liquid film velocity. Notably, while rainfall intensity predominantly affects windward-side film velocity, train speed is found to be the dominant factor for leeward-side velocity via wake flow modulation. (3) At a fixed train speed, both the side and drag forces increase with intensified rainfall. This phenomenon arises from raindrop im­ pingement on the train nose and windward surfaces, concurrently resulting in reduced lift. Notably, intensified rainfall amplifies raindrop impacts on the train nose, inducing expansion and en­ hancement of the windward positive pressure zone while attenu­ ating the negative pressure zone in the wake region. Conversely, increased train speed promotes spatial extension of the negative pressure zone within the wake of the train. At constant rainfall intensity, train speed predominantly influences the aerodynamic performances. As the speed increases, the side force on the head car rises, whereas it decreases for the middle and tail cars. The lift force decreases for the head car but increases for the middle car, while drag increases for all cars. (4) Rainfall intensity and train speed exhibit shared features in their influences on the flow around the train. Rainfall intensity imposes 15 M. Dong, R. Li, J. Xu et al. Advances in Wind Engineering 2 (2025) 100083 Li, G.Z., Deng, E., Ni, Y.Q., Ouyang, D.H., Yang, W.C., 2024a. Nonlinear spatiotemporal characteristics of wind-rain flow around the trains passing through the tunnel en­ trance during rainstorms. Nonlinear Dynamics 112, 13825–13843. https://doi.org/ 10.1007/s11071-024-09777-4 Li, M.X., Yu, M.G., Liu, J.L., Sheng, X.G., 2024b. Analysis of water film distribution and aerodynamic performances of high-speed train under rainfall environment. Chinese Journal of Mechanical Engineering 37, 137. https://doi.org/10.1186/s10033-02401120-7 Menter, F.R., 1994. Two-equation eddy-viscosity turbulence models for engineering ap­ plications. AIAA Journal 32, 1598–1605. https://doi.org/10.2514/3.12149 Ning, L., 2024. Study on disaster chain risk of railway accidents in perilous mountainous area based on multi-factor coupling. Dalian Jiaotong University, China. https://doi. org/10.26990/d.cnki.gsltc.2024.000050. (in Chinese). Ouyang, D.H., Deng, E., Ni, Y.Q., Yang, W.C., Chen, Z.W., 2023. Evolution of flow field around high-speed trains meeting at the tunnel entrance under strong wind-rain environments. Journal of Wind Engineering and Industrial Aerodynamics 241, 105537. https://doi.org/10.1016/j.jweia.2023.105537 Patel, P.Y., Liu, J.H., Vantsevich, V.V., Koomullil, R.P., 2022. Modelling effect of rain on aerodynamic performance of the Ahmed body. AIAA SCITECH 2022 Forum, CFD Applications II. https://doi.org/10.2514/6.2022-0335 Peng, Y.H., He, X.H., Jing, H.Q., Xie, N.C., 2021. Study on aerodynamic characteristics of high-speed train during wind-rain coupling through wind tunnel test. Journal of Central South University (Science and Technology) 52, 3353–3365. https://doi.org/ 10.11817/j.issn.1672-7207.2021.09.037. (in Chinese). Raeesi, A., McAuliffe, B., Galler, J., 2023. Impact of precipitation drag on a road vehicle. SAE Technical Paper 2023-01-0792. https://doi.org/10.4271/2023-01-0792. Sheng, X.G., Yu, M.G., Liu, J.L., 2022. Analysis of rain load and aerodynamic char­ acteristics of high-speed train under heavy rainfall environment based on M-P rain­ drop size distribution. Acta Aerodynamica Sinica 40, 122–128. https://doi.org/10. 7638/kqdlxxb-2021.0245. (in Chinese). Sheng, X.G., Yu, M.G., Dai, Z.Y., Zhang, Q., 2025a. Effect of raindrop particle size dis­ tribution on aerodynamic performance of high-speed train. Journal of Mechanical Engineering 61, 238–248. https://doi.org/10.3901/JME.2025.06.238. (in Chinese). Sheng, X.G., Yu, M.G., Li, M.X., Liu, J.L., 2025b. Coupling mechanism of airflow field and rain field of high-speed train under heavy rainfall environment. Journal of Mechanical Engineering 61, 241–250. https://doi.org/10.3901/JME.2025.12.241. (in Chinese). Singh, N., Kroells, M., Li, C.X., Ching, E., Ihme, M., Hogan, C.J., Schwartzentruber, T.E., 2021. General drag coefficient for flow over spherical particles. AIAA Journal 60, 587–597. https://doi.org/10.2514/1.J060648 Sun, Z.B., Du, L.M., 2018. Influence of rainfall on aerodynamic characteristics of high speed trains based on gamma rainfall spectrum. Journal of Dalian Jiaotong University 39, 24–29. https://doi.org/10.13291/j.cnki.djdxac.2018.06.006. (in Chinese). TB/T 3503.4-2018, 2018. Railway applications - Aerodynamics - Part 4: Requirements for train aerodynamic simulation. (in Chinese). Wang, X.J., Li, Q.S., Li, J.C., 2020. Field measurements and numerical simulations of wind-driven rain on a low-rise building during typhoons. Journal of Wind Engineering and Industrial Aerodynamics 204, 104274. https://doi.org/10.1016/j. jweia.2020.104274 Wang, H., Si, T.W., Zheng, S.X., Ma, S., Zhou, Y.Q., 2023. Safety of metro train operation on Nanjing Dashengguan Yangtze river bridge under combined wind-rain action. Urban Mass Transit 26, 111–117. https://doi.org/10.16037/j.1007-869x.2023.06. 020. (in Chinese). Wu, Z.L., Cao, Y.H., 2017. Airfoil performance degradation by coupling effects of su­ percooled raindrop icing and heavy rainfall. Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering 231, 2384–2395. https://doi.org/10.1177/0954410016664930 Yu, M.G., Liu, J.L., Dai, Z.Y., 2021a. Aerodynamic characteristics of a high-speed train exposed to heavy rain environment based on non-spherical raindrop. Journal of Wind Engineering and Industrial Aerodynamics 211, 104532. https://doi.org/10.1016/j. jweia.2021.104532 Yu, M.G., Liu, J.L., Li, T., Zhang, Q., 2021b. Operational safety characteristics of highspeed train under strong wind and rainfall environment. Journal of Mechanical Engineering 57, 172–180. https://doi.org/10.3901/JME.2021.20.172. 193 (in Chinese). Yu, M.G., Liu, J.L., Zhang, Q., Dai, Z.Y., 2022. Unsteady aerodynamic characteristics on trains exposed to strong wind and rain environment. Journal of Wind Engineering and Industrial Aerodynamics 226, 105032. https://doi.org/10.1016/j.jweia.2022.105032 Yue, Y.F., Zeng, Q.L., Li, Z.S., Lu, F.A., 2016. Numerical simulating effects of rain-loaded wind on the aerodynamic characteristics and running stability of high-speed trains. Journal of Desert Research 36, 943–950. https://doi.org/10.7522/j.issn.1000-694X. 2015.00112. (in Chinese). Zeng, G.Z., Li, Z.W., Huang, S., Chen, Z.W., 2023a. Aerodynamic characteristics of in­ tercity train running on bridge under wind and rain environment. Alexandria Engineering Journal 66, 873–889. https://doi.org/10.1016/j.aej.2022.10.058 Zeng, G.Z., Li, Z.W., Huang, S., Chen, Z.W., 2023b. Influence of wind and rain environ­ ment on operational safety of intercity train running on the viaduct. International Journal of Numerical Methods for Heat & Fluid Flowing 33, 1584–1608. https://doi. org/10.1108/HFF-12-2022-0693 Zhang, W.Z., Hu, Y.X., Zeng, S.Q., Tan, L.F., 2025b. Performance analysis of high-speed trains passing through a multi-span railway cable-stayed bridge under cross winds. Journal of Railway Science and Engineering Journal of Railway Science and Engineering 22, 1899–1911. https://doi.org/10.19713/j.cnki.43-1423/u. T20241580. (in Chinese). Zhang, L., Yang, M.Z., Liang, X.F., 2018. Experimental study on the effect of wind angles on pressure distribution of train streamlined zone and train aerodynamic forces. Journal of Wind Engineering and Industrial Aerodynamics 174, 330–343. https://doi. org/10.1016/j.jweia.2018.01.024 Zhang, W.T., Ye, G.L., Leung, J.C.H., Zhang, B.L., 2025a. Microphysical characteristics of summer precipitation over the Taklamakan desert based on GPM-DPR data from 2014 to 2023. Atmosphere 16, 354. https://doi.org/10.3390/atmos16040354 Zhao, C.Y., 2022. Driving rainfall by wind: Changes in raindrop characteristics and rainfall erosivity. Beijing Forestry University, China. https://doi.org/10.26949/d. cnki.gblyu.2022.000301. (in Chinese). Zoumb, P.A.W., Bwemba, C., Mbessa, M., Moussus, T.W., Kemta, L.P., 2025. Train-bridge interaction under correlated wind and rain using machine learning. Advances in Structural Engineering 28, 1627–1644. https://doi.org/10.1177/ 13694332251313867 16
0
You can add this document to your study collection(s)
Sign in Available only to authorized usersYou can add this document to your saved list
Sign in Available only to authorized users(For complaints, use another form )