Executive Summary of ASME IX Article I: Welding General Requirements Group Project Prepared by: Omarion Johnson Zachary Redman Azarion Ross Aqeelah Watson Reuben Williams Elijah Wright 05 NOV 2025 Table of Contents Member Responsibilities QW-100 (Scope) to QW-144 (Visual Examination) QW-150 (Tension Tests) to QW-163 (Bend Tests) QW-170 (Toughness Tests) to QW-185.3 (Diffusion Welding) QW-190 (Other Tests and Examinations) to QW-192.2.2 (Stud Weld Tests) QW-193 (Tube to Tube-Sheet Tests) to QW-196.2.2 (Resistance Weld Testing) QW-197 (Laser Beam Welding Lap Joint Tests) - Appendix I 2 2 3 3 3 3 3 Member Responsibilities Zachary Redman shall be responsible for QW100 (Scope) to QW144 (Visual Examination) Azarion Ross shall be responsible for QW150 (Tension Tests) to QW163 (Bend Tests) Omarion Johnson shall be responsible for QW170 (Toughness Tests) to QW185.3 (Diffusion Welding) Aqeelah Watson shall be responsible for QW190 (Other Tests and Examinations) to QW192.2.2 (Stud Weld Tests) Reuben Williams shall be responsible for QW193 (Tube to Tube-Sheet Tests) to QW196.2.2 (Resistance Weld Testing) Elijah Wright shall be responsible for QW197 (Laser Beam Welding Lap Joint Tests) - Appendix I QW-100 (Scope) to QW-144 (Visual Examination) Section QW-100 addresses the scope of this section of the document as it pertains to the preparation of Welding Procedure Specifications, and the qualifications of welding procedures, welders, and welding operators of all types of manual and machine welding processes permitted in this Part. Section QW-101 states that any WPS a company uses shall have been qualified by that company in accordance with Article II OR be an AWS Standard Welding Procedure (found in Mandatory Annex E). The WPS addresses the variables found in whatever procedure the company plans to use in production. Section QW-102 states the basic criteria for establishing if a welder is qualified or not is the welder’s ability to deposit sound weld metal. Section QW-103 covers who is responsible for conducting welder qualification tests, as well as stating that records of test results shall be maintained. Section QW-110 references illustrations of weld orientations found in Figure QW-461.1 or FIgure QW-461.2. Section QW-120 describes test positions for groove welds. Section QW-121 describes the acceptable plate positions. Section QW-122 describes acceptable pipe positions. Section QW-123 describes acceptable positions for stud welds. Section QW-124 states any position other than those described in Sections QW-120 through QW-123 are termed “special positions”. Section QW-130 describes test positions for fillet welds. Section QW-131 describes the acceptable plate positions. Section QW-132 describes acceptable pipe positions. Section QW133 states any position other than those described in Sections QW-130 through QW-132 are termed “special positions”. Section QW-140 covers the different types and purposes of tests and examinations. Section QW-141 covers mechanical tests such as tension tests, guided-bend tests, fillet-weld tests, toughness tests, and stud weld tests. Section QW-142 states that radiographic or ultrasonic testing per QW-191 may be substituted for the mechanical tests of Section QW 141 for grooveweld performance qualification as permitted by QW-304 to prove the welder’s ability to produce a sound weld. Section QW-143 states that radiographic or ultrasonic testing per QW-191 may be substituted for the mechanical tests of Section QW 141 for groove-weld performance qualification as permitted by QW-305 to prove the welding operator’s ability to produce a sound weld. Lastly, Section QW-144 covers the visual examination as described in QW-194, which is used to determine that final weld surfaces meet specified quality standards. In short, if it looks like shit, it ain’t passing. QW-150 (Tension Tests) to QW-163 (Bend Tests) Section QW-150 covers all aspects of the tension tests. Section QW-151 covers the requirement that shall be met in order for a reduced plate and reduced pipe tensile test or tests to be conducted, in accordance with figures QW-462.1(a) through QW- 462.1(e) for the plate, figure QW-462.1(b) for pipe, and QW-153. It also explains the requirements for turned specimens and full-section specimens for pipe which is in accord with figure QW-462.1(e). Section QW-152 describes how the tension test procedure will be conducted. Section QW-153 discusses what the acceptance criteria is according to tensile strength. Section QW-160 covers guided-bend tests. Section QW-161 covers how bend-test specimens must be cut, prepared and tested. It defines the face, root, and side surfaces of each specimen, gives requirements for specimen size, and states that materials with very low elongation must use a macro-etch test instead of a bend test. It also describes the five types of guided-bend test which are transverse side, face, and root bends. Also subsize transverse bends for small pipes and longitudinal face and root bends and explains when each type is used. Lastly, it covers that multiple specimens may be required to cover the full weld area and that all specimens shall meet ASME acceptance requirements. Section QW-162 covers the procedure for guided-bend test in jigs and refers to figures QW466.1, QW-466.2, and QW-466.3 for a visual of what the set up should look like. Section QW163 covers the acceptance criteria for the guided-bend test. QW-170 (Toughness Tests) to QW-185.3 (Diffusion Welding) Section QW-170 addresses the requirements for toughness testing when a referencing code requires it. It states that the test procedures and equipment must follow the rules of the referencing code, or SA-370 if the code does not provide its own rules. Section QW-171 explains general toughness test rules, including acceptance criteria, and notes that toughness specimens must be removed and prepared according to the Section that requires the tests. It also specifies that when qualifying pipe in the 5G or 6G position, specimens must come from the shaded area shown in Figure QW-463.1(f). Section QW-172 describes drop-weight toughness tests, which must also follow the referencing code or ASTM E208 when not specified. The acceptance criteria again come from the Section that requires the test, and specimen location rules match those in QW-171, including the shaded region for 5G or 6G pipe. Section QW-180 covers the required tests for fillet-weld procedure and performance qualification. It explains how the test coupons are to be prepared, cut, and examined for both procedure and performance qualification. Section QW-181 details the dimensions and preparation of fillet-weld specimens for both procedure and performance qualification. Procedure specimens are sectioned and macro-etched, while performance specimens are subjected to fracture testing and macro-examination. Production mockups may also be used under controlled conditions. Section QW-182 explains the fracture test requirements for fillet-weld performance specimens. The specimen is loaded laterally so the root is in tension; it must not show evidence of cracks, incomplete fusion, or excessive inclusions or porosity. Section QW-183 describes macro-examination requirements for procedure specimens. Welds must show complete fusion, no cracks, and no more than 1/8 in. difference between fillet leg lengths. Section QW-184 provides macro-examination criteria for performance specimens. Fusion must be complete, cracks are not permitted, concavity/convexity is limited to 1/16 in., and fillet leg sizes must not differ by more than 1/8 in. Linear root indications up to 1/32 in. are acceptable. Section QW-185 introduces diffusion welding for both procedure and performance qualification. It specifies the minimum size of the test block and the number of interface planes required. Section QW-185.1 states that diffusion-welding test blocks must be at least 8 in. × 8 in. and thick enough to produce at least 50 welded interface planes. Section QW-185.2 requires that six tension tests be performed—three perpendicular and three parallel to the interface planes—and the results must comply with the tension test acceptance criteria of QW-153. Section QW-185.3 mandates microstructural evaluation of at least three cross-sections (top, middle, and bottom thirds of the block). The samples must be polished, etched, free of cracks, and show no incomplete bonding or porosity at or near the bond lines. Examination must be performed at 50× to 100× magnification. QW-190 (Other Tests and Examinations) to QW-192.2.2 (Stud Weld Tests) Section QW-190 covers the different types of extra testing used to qualify welders and welding operators, mainly radiographic and ultrasonic tests. It outlines how these tests must be performed and evaluated Section QW-191.1 covers radiographic testing and how it must follow section V rules. It focuses on ensuring image quality, which determines whether welds are accepted or rejected based on the visibility of discontinuities like cracks, slag, or porosity shown on the X-ray. Section QW-191.2 covers ultrasonic examinations. UT Testing can be used instead of RT for thicker materials and requires a written procedure. Any indication that looks like a crack or lack of fusion is automatically unacceptable. Section QW-191.3 covers records of tests. Requires that all results from RT or UT welder qualification exams be formally documented. Section QW-191.4 covers personnel qualifications. Anyone performing RT or UT must be properly trained and certified under their company’s written practice that meets Section V requirements. Section QW-192 covers how to test stud welding procedures and operators, using bend, hammer, torque, or tensile tests to confirm that each stud weld is strong and has no cracking or separation. Section QW-192.1 describes the procedure qualification for stud welding. A stud/welding procedure must be proven by welding ten studs and testing them. Half by bending/hammering and half by torque or tensile testing to show the welds hold up without cracking. Section QW-192.2 covers performance qualification for stud welding. To qualify a stud-welding operator, they must weld five studs and each one must pass a bend or hammer test with no signs of cracking or separation. QW-193 (Tube to Tube-Sheet Tests) to QW-196.2.2 (Resistance Weld Testing) Section QW-193 covers tube-to-tube sheet weld procedure qualifications using mockups and macro examinations. Qualifies procedures for tube-to-tube sheet welds, common in boilers and heat exchangers. QW-193.1.1 Checks fusion, porosity, cracking, burn-through, through visual inspection QW-193.1.2 Liquid penetrant testingPer Section V, Article 6 QW-193.1.3 magnification after etching to verify fusion and leakage path Strength calculations Weld thickness must be calculated per UW-20.6 to ensure mechanical strength Essential variables Defined in QW-288 adding process-specific requirements QW-194 scope: provides visual examination criteria for weld test coupons Requirements: visual inspection of plate and pipe coupons before mechanical testing. Welds must show complete fusion, no cracks, no porosity and no burn through. Additional testing may include radiography, ultrasonic, bend, or tensile tests depending on WPS. QW-195 - liquid penetrate examination QW-195.1- the liquid penetrant examination in QW-214 for corrosion-resistant weld metal overlay shall meet the requirements of section V, Article 6. The liquid penetrant examiners shall meet the requirements in QW-195.3. The acceptance standards of QW-195.2 shall be met. QW-195.2- liquid penetrant acceptance criteria QW-195.2.1- terminology. Relevant indications with major dimensions greater than 1/16th in. (1.5 mm) Linear indications an indication having a length greater than three times the width. Rounded indicates an indication of circular or elliptical shape with the length equal to or less than three times the width. QW-195.2.2 Acceptance standards. The weld overlay must meet acceptance criteria defined in QW-195.2. These standards specify what types of indications (linear, rounded, etc.) are acceptable or rejectable based on size, number, and distribution. QW-195.3 Personal certification: the organization shall verify the personnel performing the liquid penetrate examinations meet the following requirements, correct vision with corrections if needed, be able to differentiate colors with contrast being used. Shall be checked annually. QW- 196 resistance weld testing QW- 196.1 macro- examination welds shall be cross sectioned, etched, and polished to reveal the weld metal. The section shall be examined at 10x magnification. Porosity shall not exceed one void in the transverse cross section of a specimen. The maximum dimension of any void shall not exceed 10% of the thickness of the weld bead. QW 196.1.2 spot and seam weld minimum diameter or width of weld nugget QW 196.1.3 projection welds the nugget shall not be less than 80% of the width of projection. QW 196.2 Mechanical testing QW 196.2.1- shear test specimens shall be prepared as shown in figure QW 462.9. Test calculations shall be used using table QW/QB-422 for the weaker of the two based metals joined. QW 196.2.2 - peel test shall be prepared as shown in figure QW- 462.8.1 for spot and projection welding And per QW-462.8.2 for seam welds.specimens shall be peeled mechanically and fracture shall occur in the base metal by tearing out the weld in order for the specimen to be acceptable. QW-197 (Laser Beam Welding Lap Joint Tests) - Appendix I Procedure Qualification — QW-197.1 QW-197.1.1 Required Tests ● Six tension-shear specimens required. ● Eight macro-examination specimens required. ● Test coupon must follow Figure QW-464.1. ● Tension-shear specimens must follow dimensions in Fig. QW-464.1 table. ● Longitudinal and transverse sections must be taken near weld centerline (per Fig. QW464.1). ● Longitudinal specimens must have at least 1 in. (25 mm) for examination. ● Transverse specimens must include weld, HAZ, and base metal. ● Specimens must be smoothed, etched (per QW-470), and examined at 25X magnification. ● Fusion zone size and penetration must be measured to 0.01 in. QW-197.1.2 Acceptance Criteria — Tension-Shear Tests ● Must meet requirements of QW-153. QW-197.1.3 Acceptance Criteria — Macro-Examination Each of the eight macro specimens must show: ● (a) Fusion zone outline consistent in size, regular in shape, and uniform in penetration. ● (b) Sound weld metal, complete fusion along bond line, and no cracks in weld metal or HAZ. 2. Performance Qualification — QW-197.2 QW-197.2.1 Required Tests ● One peel test specimen at least 6 in. (150 mm) long (see Fig. QW-464.2(a)). ● Macro specimens as shown in Fig. QW-464.2(b). ● Peel specimen peeled apart to destruction; fusion zone and penetration measured to 0.01 in. ● Macro specimens must be polished, etched, and examined same as QW-197.1. QW-197.2.2 Acceptance Criteria — Peel & Macro ● Average fusion zone dimensions and average penetration must fall within the ranges specified on the WPS used to weld the test coupon
0
You can add this document to your study collection(s)
Sign in Available only to authorized usersYou can add this document to your saved list
Sign in Available only to authorized users(For complaints, use another form )