Flight Training Manual Cessna C172S Rev. 1 01/26/2024 Introduction This Kansas State University Flight Training Manual (FTM) has been designed to provide the pilot with standardized procedures for safe and efficient training operations in the Cessna 172S. It is your responsibility to have a complete and thorough knowledge of these procedures and techniques. Note that this manual does not include all the information found in the Pilot’s Operating Handbook (POH). It is primarily a procedures guide and is to be used as a supplement to the POH, and in conjunction with FAA Handbooks, and the appropriate Airman Certification Standards (ACS). The procedures in this manual are not intended to limit the pilot’s judgment. The pilot can alter procedures to meet existing conditions. No procedure, regardless of how well written, can account for every possible variable; a procedure cannot replace common sense. ©2024 Kansas State University - Salina Aerospace and Technology Campus All Rights Reserved Revision Log Revision Number Date Page Revision Description Initials Original 01/25/2024 All Original Document JG Rev. 1 01/26/2024 3-1 Rev. 1 LJU Misc. Notes Flap speeds This page is intentionally left blank. Table of Contents Section 1: General Information Airpseeds....................................................................................................................1-1 Emergency Airspeeds............................................................................................1-1 Pre- and Post-Maneuver Checklist....................................................................1-2 Training Cruise Flight.............................................................................................1-2 Section 2: Takeoffs, Landings, and Pattern Normal Takeoff, Traffic Pattern, and Landing................................... 2-1 & 2-2 Crosswind Takeoff, Traffic Pattern, and Landing........................................ 2-2 Balked Landing (Go Around).............................................................................. 2-2 Touch and Go........................................................................................................... 2-3 Short-Field Takeoff and Landing...................................................................... 2-3 Soft-Field Takeoff and Landing......................................................................... 2-4 Power-Off 180.......................................................................................................... 2-4 Traffic Pattern Visualized..................................................................................... 2-5 Section 3: Slow Flight and Stalls Maneuvering During Slow Flight...................................................................... 3-1 Power-Off Stall......................................................................................................... 3-1 Power-On Stall......................................................................................................... 3-2 Accelerated Stall..................................................................................................... 3-2 Section 4: Performance Maneuvers Steep Turns............................................................................................................... 4-1 Chandelle.................................................................................................................. 4-1 Lazy Eight.................................................................................................................. 4-1 Steep Spiral............................................................................................................... 4-2 Section 5: Ground Reference Maneuvers Rectangular Course............................................................................................... 5-1 S-Turns........................................................................................................................ 5-1 Turns Around A Point............................................................................................ 5-1 Eights on Pylons...................................................................................................... 5-2 Table of Contents Section 6: Instrument Flight Instrument Rules of Thumb................................................................................ 6-1 The 5 T’s of Instrument Flight............................................................................ 6-2 The STIMEE Check.................................................................................................. 6-3 Instrument Briefings.................................................................................. 6-4 & 6-5 Lost Communications Procedures................................................................... 6-6 Lost Communications in IMC.................................................................. 6-7 & 6-8 Precision Approach Procedures.......................................................... 6-9 & 6-10 Non-Precision Approach Procedures............................................. 6-11 & 6-12 Circling Approach Procedures.......................................................... 6-13 & 6-14 Holding Procedures............................................................................. 6-15 to 6-18 Arc Intercept Procedures..................................................................... 6-19 & 6-20 This page is intentionally left blank. Section 1: General Information Airspeeds All airspeeds used throughout this manual are knots indicated airspeeds (KIAS) and assume zero instrument error. VSO VS1 VR VX VY VFE VA VNO VNE Stall, landing configuration.............. 40 Stall, clean configuration................... 48 Rotation................................................... 55 Best Angle of Climb............................. 62 Best Rate of Climb................................ 74 Maximum Flap Extension.................. 85/110 Maneuvering Speed............................ 105 Maximum Structural Cruising.......... 129 Never Exceed......................................... 163 Emergency Descent.............................125 Best Glide................................................. 68 Airspeeds for Emergency Operations Engine Failure After Takeoff Wing Flaps UP............................................................................ 70 KIAS Wing Flaps 10°............................................................................ 65 KIAS Maneuvering Speed 2550 POUNDS.......................................................................... 105 KIAS 2200 POUNDS............................................................................ 98 KIAS 1900 POUNDS............................................................................ 90 KIAS Maximum Glide...................................................................... 68 KIAS Precautionary Landing with Engine Power..... 65 KIAS Landing Without Engine Power Wing Flaps UP............................................................................ 70 KIAS Wing Flaps 10°-FULL................................................................ 65 KIAS 1-1 General Information Pre- and Post-Maneuver Checklist This checklist is to be performed prior to and at the completion of any maneuver. (H)eight........................................................................................................... As Required (A/R) All maneuvers (except ground reference maneuvers) must be performed at an altitude that allows recovery above 1500 feet AGL. Ground reference maneuvers will be performed at 1000 feet AGL. (E)ngine Instruments/ESP.................................................................................. CHECK/SET A/R (L)ocation ........................................................................................................................... NOTE Note location to ensure that maneuvers are being performed in a safe area away from towns, built-up areas, and airspace. Be within gliding distance of an emergency landing site. In the event of an emergency, be able to notify ATC of your location before landing. (L)ookout ................................................................................................................... COMPLETE Two 90 degree turns or one 180 degree turn with no more than 30 degrees of bank will be executed to be certain that the airspace is clear. Always maintain a constant lookout for traffic. Training Cruise Flight Adjust pitch to maintain altitude. Set power to maintain 90 KIAS (approximately 2100-2300 RPM). Perform Cruise checklist. 1-2 General Information General Briefings Passenger Briefing Once all occupants are seated and before engine start, the PIC must conduct a passenger briefing; the mnemonic “SAFETY” covers all the required briefing items: S - Seat belts, shoulder harnesses and seating position Seat belts - how do they operate? Shoulder harnesses - are they secured? Seating position - are you comfortable? A - Air vents, all environmental factors, and action Air vents - where are they and how do they work? All environmental factors Action - in the event of passenger discomfort or sickness F - Fire extinguisher Fire extinguisher - where is it and how does it work? E - Exit doors, emergency evacuation plan, emergency equipment Exit doors - location and operation Emergency evacuation plan Emergency equipment - location T - Traffic scanning and talking Traffic scanning - includes passengers Talking - sterile cockpit during parts of the flight (especially during taxi, takeoff, and landing) Y - Your questions? 1-3 General Information General Briefings (cont.) Takeoff Briefing Before takeoff, the PIC must conduct a takeoff brief, discussing the following items: Runway number, length, and takeoff distance required Initial heading/direction/altitude OR instrument departure procedure Procedures to be followed in an emergency The following is an example of a takeoff briefing: Today we will be departing on runway ___ on a heading of ___ up to __ feet. We have ___ of available runway and require ___ feet for takeoff. If there is an abnormality or emergency prior to rotation, I will close the throttle and apply maximum braking to stop on the runway. If there is an engine failure after rotation with sufficient runway, I will close the throttle and land straight ahead. Finally, if there is an engine failure after rotation without sufficient runway, I will pitch for best glide and land where practical. 1-4 General Information Section 2: Takeoffs, Landings, and Pattern Normal Takeoff, Traffic Pattern, and Landing Takeoff and Upwind Complete Before Takeoff checklist. Align airplane with runway centerline. Verify correct runway. Advance throttle smoothly to full power. Maintain directional control on the runway centerline. Check engine instruments. Normal static full power 2300-2400 RPM and oil temperature and pressure in green arc. Rotate at 55 KIAS with 10° flaps. Pitch for 10° degrees nose up for 74 KIAS (VY) for climb. Retract flaps at safe altitude and at or above 60 KIAS. Maintain a straight track over the extended runway centerline until 300 feet below traffic pattern altitude and past departure end of runway. Turn with medium bank (do not exceed 30° bank) to crosswind leg or depart the traffic pattern. Crosswind Maintain perpendicular ground track to the runway. Scan for traffic. Turn with medium bank (do not exceed 30° bank) to downwind leg within 1/2-1 miles of the runway. Downwind Level off at pattern altitude. Establish speed of 90 KIAS, power about 2100-2300 RPM. Perform Before Landing checklist. Abeam Touchdown Point Reduce power to 1500-1700 RPM (as required). Verify airspeed is below 110 KIAS. Set flaps to 10° (as required). Establish speed of 80 KIAS. Turn with medium bank (do not exceed 30° bank) to base leg when approximately 45° from touchdown point. 2-1 Takeoffs, Landings, and Pattern Normal Takeoff, Traffic Pattern, and Landing (cont.) Base Maintain perpendicular ground track to the runway. Verify airspeed is below 85 KIAS. Set flaps to 20° (as required). Establish 75 KIAS. Scan final approach for traffic. Turn with medium bank (do not exceed 30° bank) to final approach. Final Approach Align the longitudinal axis of the airplane with the runway centerline. Verify airspeed is below 85 KIAS. Set flaps to 30° upon rolling out from turn (as required). Establish stabilized approach at 65 KIAS. Touchdown smoothly on the main landing gear at the approximate stalling speed with no drift and the airplane over the runway centerline. Keep the nosewheel off the runway with aft control wheel as long as practical. Exit runway and complete the After Landing checklist. Crosswind Takeoff and Landing Takeoff and Upwind Same procedure as a Normal Takeoff. Turn ailerons into the wind. Use rudder to maintain directional control on the runway centerline. Add 5 KIAS to the rotation speed for crosswinds greater than 6 knots. Establish a positive rate of climb. Remove the slip and establish crab angle. Landing Same procedure as a Normal Landing. If winds are strong, consider using less than full flaps. Establish sideslip on final approach. Drift is controlled with aileron and the heading is controlled with rudder. Touchdown on the upwind main wheel first. As airplane slows, increase aileron deflection for ground crosswind correction. Balked Landing (Go-Around) Procedure Make timely decision to discontinue the approach. Apply full power. Retract flaps to 20°. Establish the climb speed at 60 KIAS. Retract flaps to 10° after obstacles are cleared. Retract flaps to 0° after reaching 65 KIAS. 2-2 Takeoffs, Landings, and Pattern Touch and Go Procedure Flaps up. Trim set to takeoff. Apply full power. Use rudder to maintain runway centerline. Rotate at 55 KIAS. Establish 10° pitch for 74 KIAS. Short-Field Takeoff and Landing Takeoff Complete Before Takeoff checklist. Extend flaps to 10°. Utilize the full length of runway. Align airplane with runway centerline. Verify correct runway. Hold brakes and advance throttle smoothly to full power. Check engine instruments Normal static full power 2300-2400 RPM and oil temperature and pressure in green arc. Release brakes. Use rudder to maintain directional control on the runway centerline. Hold elevator slightly tail low. Liftoff at 51 KIAS. Pitch for 56 KIAS until clear of obstacles (approximately 12°-15° nose up). Lower pitch attitude to climb at VY (approximately 10° nose up). Retract flaps when airspeed is greater than 60 KIAS. Landing Same procedure as a Normal Landing using a slower airspeed on final with a steeper angle of descent. Set flaps to full. Fly final approach at 61 KIAS. Touchdown smoothly at approximate stalling speed. Apply maximum braking without wheel lockup with full aft control wheel and flaps up or announce “Maxiumum braking”. 2-3 Takeoffs, Landings, and Pattern Soft-Field Takeoff and Landing Takeoff Complete Before Takeoff checklist. Extend flaps to 10°. Hold control wheel full aft during taxi. Continue rolling from taxiway into the takeoff roll. Advance throttle smoothly to full power. Reduce back elevator pressure to keep nose wheel off the runway. Use rudder to maintain directional control on the runway centerline. Check engine instruments. Normal static full power 2300-2400 RPM and oil temperature and pressure in green arc. As the airplane lifts off, reduce the back pressure to remain in ground effect. Accelerate to 56 KIAS in ground effect. Smoothly pitch to an attitude that will yield VY (74 KIAS) or VX as required. Retract flaps when airspeed is more than 60 KIAS. Landing Same procedure as a Short-Field Landing except... Maintain some power (1000-1200 RPM) during the flare. Touchdown smoothly, power as required. Hold control wheel aft to keep the nosewheel off the runway as long as practical. Power Off 180 Abeam touchdown point, reduce power to idle. Establish 68 KIAS, flaps UP or 10°. Evaluate when to turn base: As wind speed increases, turn base earlier. Evaluate glideslope: If you are high, execute a forward slip (preferred) or extend flaps In strong winds, increase indicated airspeed slightly above 68 KIAS Do not attempt to stretch your glide by pitching up. This will reduce your glide performance. Touchdown at the proper pitch attitude over the runway centerline with no sideload. Do NOT force the airplane onto the touchdown point. Do NOT pitch up excessively (more than 10 degrees nose up) to hold the airplane off the runway. 2-4 Takeoffs, Landings, and Pattern Traffic Pattern Visualized Upwind Downwind Crosswind Maintain perpendicular ground track to the runway. Scan for traffic. |||||| |||||| Turn with medium bank* to downwind leg within 1/2-1 miles of the runway. Level off at pattern altitude. Establish speed of 90 KIAS, power about 2100-2300 RPM. Perform Before Landing checklist. Maintain a straight track over the extended runway centerline until 300 feet below traffic pattern altitude and past departure end of runway. Turn with medium bank* to crosswind leg. 17 | | Abeam Touchdown Point || || Reduce power to 1500-1700 RPM (as required). Verify airspeed is below 110 KIAS. Set flaps to 10° (as required). Establish speed of 80 KIAS. Turn with medium bank* to base leg when approximately 45° from touchdown point. || || ||| ||| 35 |||||| |||||| Final Approach Base Maintain perpendicular ground track to the runway. Verify airspeed is below 85 KIAS. Set flaps to 20° (as required) Establish 75 KIAS. Scan final approach for traffic. Turn with a medium bank* to final approach. Align the longitudinal axis of the airplane with the runway centerline of runway. Verify airspeed is below 85 KIAS. Set flaps to 30° upon rolling out from turn (as required). Establish stabilized approach at 65 KIAS. Execute desired landing. *Do NOT exceed 30° of bank while turning 2-5 Takeoffs, Landings, and Pattern 1-2 General information This page is intentionally left blank. 2-6 Takeoffs, Landings, and Pattern Section 3: Slow Flight and Stalls Maneuvering During Slow Flight Complete Pre-Maneuver Checklist. Reduce power to 1500-1700 RPM (as required). Extend flaps to 10º at 90 KIAS. Extend flaps to 20º at 80 KIAS. Extend flaps to FULL at 75 KIAS. Adjust pitch to establish Minimum Controllable Airspeed (MCA). Add power to maintain altitude (usually bottom of the green arc on tachometer). Add right rudder to maintain coordination and heading. Perform maneuvers as specified. To recover, first apply full power. Retract flaps to 20°. Establish airspeed at 60 KIAS. Retract flaps to 10° above 60 KIAS. Retract flaps to 0° after reaching 65 KIAS. Recover to training cruise flight. Power-Off Stall Complete Pre-Maneuver Checklist. Reduce power to 1500-1700 RPM (as required). Extend flaps to 10º at 90 KIAS. Extend flaps to 20º at 80 KIAS. Extend flaps to FULL at 75 KIAS. Establish a stabilized descent. Maintain initial heading or bank as specified, not to exceed 20° of bank. Reduce power to idle. Increase pitch to a landing attitude (approximately 5-10 degrees nose up). Announce the first indication of a stall. Recover OR execute full stall. Recover promptly by decreasing pitch attitude. Level the wings. Apply max power and coordinate with rudder. Minimize loss of altitude. Retract flaps to 20°. Establish the climb speed at 60 KIAS. Retract flaps to 10° above 60 KIAS. Retract flaps to 0° after reaching 65 KIAS. Recover to training cruse flight. 3-1 Slow Flight and Stalls Power-On Stall Complete Pre-Maneuver Checklist. Reduce power to 1500-1700 RPM. Slow to 74 KIAS (simulating initial climbout VY). Maintain initial heading or bank as specified, not to exceed 20° of bank. Apply max power. Increase pitch up to approximately 18-22 degrees nose up. Announce the first indication of a stall. Recovery OR execute a full stall. Recover promptly by decreasing pitch attitude. Level the wings. Minimize loss of altitude. Accelerate to and climb at 62 KIAS (VX) or 74 KIAS (VY) as specified. Recover to training cruise flight. Accelerated Stall Complete Pre-Maneuver Checklist and ensure adequate altitude is used (Airman Certification Standards require recovery at or above 3,000' AGL). Reduce power to 1500-1700 RPM. Increase pitch to stall attitude while maintaining altitude to slow down. Slow to 75 KIAS (simulating airspeed on base). Upon reaching 75 KIAS, bank to 45° and add elevator back-pressure. Announce the first indication of a stall. Recover promptly at first indication by decreasing pitch attitude. Level the wings. Apply full power. Minimize loss of altitude. Return to original altitude and heading or as specified by the examiner or instructor. 3-2 Slow Flight and Stalls Section 4: Performance Maneuvers Steep Turns Complete Pre-Maneuver Checklist. Establish 95 KIAS, power as required (approximately 2250-2300 RPM). Roll into a 360° turn at an angle of bank of 45° (50° for commercial). Apply power as required to maintain 95 KIAS. Begin rollout 20° before the initial heading is reached. Roll into a 360° turn at an angle of bank of 45° (50° for commercial) in the opposite direction. Begin rollout 20° before the initial heading is reached. Recover to training cruise flight. Chandelle Complete Pre-Maneuver Checklist. Establish 105 KIAS, power as required (approximately 2400 RPM). Select a 90° reference point. Establish a 30° bank turn. Apply full power and increase pitch through 90° of turn. Use rudder to maintain coordination. Hold the pitch attitude and slowly level the wings through the last 90° of turn. Use rudder to maintain coordination. Complete the maneuver at 180° of turn, airspeed just above a stall. Reduce pitch to resume straight and level flight at the final altitude. Lazy Eight Complete Pre-Maneuver Checklist. Establish 105 KIAS, power as required (approximately 2400 RPM). Select reference points at 45°, 90°, 135°, and 180°. Enter a coordinated climbing turn towards the reference point. At 45° of turn, attain 15° of bank and the maximum pitch up. At 90° of turn, attain 30° of bank, level pitch attitude, airspeed approximately 5-10 KIAS above stall speed. At 135° of turn, attain 15° of bank and the maximum pitch down. At 180° of turn, attain straight and level, initial altitude and 105 KIAS. Begin turn in the opposite direction and attain the same standards. 4-1 Performance Maneuvers Steep Spiral Complete Pre-Maneuver Checklist. Enter the maneuver downwind 1/4 to 1/2 mile from the point. Abeam the selected point, reduce power to idle and trim for best glide speed (68 KIAS) and start a turn. Maintain a constant radius through 360° of turn with varying bank and wind drift correction. Maintain coordination using rudder. Perform a clearing burst on the engine on the upwind portion (approximately 2-3 seconds of moderate power about 1500 RPM at most). Complete at least 3 turns. Recover at or above 1500 feet AGL and to training cruise flight. 4-2 Performance Maneuvers Section 5: Ground Reference Maneuvers Rectangular Course Complete Pre-Maneuver Checklist. Establish 90 KIAS, power as required (approximately 2100-2300 RPM). Altitude at 1000 ft. AGL (pattern altitude). Enter the maneuver 45° to the downwind leg. Maintain a ground track parallel to and within 1/2 mile of the course. Apply adequate wind drift correction. Exit at the point of entry. S-Turns Complete Pre-Maneuver Checklist. Establish 90 KIAS, power as required (approximately 2100-2300 RPM). Altitude at 1000 ft. AGL (pattern altitude). Select a line aligned perpendicular to the wind. Enter the maneuver downwind with 1/2 mile distance. Cross the line and roll into a bank to the left. Maintain a constant radius through 180° of turn with varying bank. Cross the line and roll into a bank to the right with the same radius. Maintain a constant radius through 180° of turn with varying bank. Recover to training cruise flight. Turns Around A Point Complete Pre-Maneuver Checklist. Establish 90 KIAS, power as required (approximately 2100-2300 RPM). Altitude at 1000 ft. AGL (pattern altitude). Enter the maneuver downwind approximately 1/2 mile from the point. Cross the line and roll into a bank to the left. Maintain a constant radius through 360° of turn with varying bank and wind drift correction. Recover to training cruise flight. 5-1 Ground Reference Maneuvers Eights on Pylons During preflight, determine the Pivotal Altitude (PA = GS knots²/11.3). Complete Pre-Maneuver Checklist. Select suitable pylons. Establish 95 KIAS, power as required. Enter the maneuver downwind at a 45° angle at the Pivotal Altitude. Maintain the line-of-sight reference line on the pylon with minimum longitudinal movement. If the pylon moves forward of the desired reference point, apply forward elevator pressure. If the pylon moves aft of the desired reference point, apply back elevator pressure. Bring wings level to enter a 45° entry for the second point. Maintain the line-of-sight reference line on the pylon with minimum longitudinal movement. If the pylon moves forward of the desired reference point, apply forward elevator pressure. If the pylon moves aft of the desired reference point, apply back elevator pressure. Rollout on the 45° to the next pylon. Recover to training cruise flight. 5-2 Ground Reference Maneuvers Section 6: Instrument Flight Instrument Rules of Thumb 1. Use of Throttle Make small power changes (less than 200 RPM) and evaluate the result. Then make small adjustments if necessary. 2. Use of Controls: Changes to pitch and bank must be small and must be made smoothly referencing the attitude indicator. Large and abrupt maneuvering will result in overshooting the intended altitude, heading, or airspeed. 3. Heading changes: Use standard rate turns (bank angle calculated with approximately 15% of KTAS). During an actual or simulated gyro failure, use ½ standard rate turns. Once the turn is established, note the angle of bank (AOB) required to maintain the turn. When turning to a heading, begin leveling the wings before reaching the new heading. To calculate how many degrees to lead the level off divide the AOB by 2 (e.g. 20° /2 =10° ). 4. Altitude changes: If 100 feet or less, use pitch only (2°-5° pitch). If more than 100 feet high or low use throttle and pitch. 5. Leveling off from climbs and descents: When leveling off from climb or descent, lead the level off by 10% of the VSI indication. For example, if descending at 500 FPM begin level off 50 feet before reaching the target altitude. When leveling off from a climb, wait until the aircraft reaches the desired cruising airspeed before reducing power. As the aircraft accelerates, trim the aircraft so that minimal pressure is required to maintain altitude. Final trimming is done after the power is reduced and airspeed is stable. 6. Cruise: Choose a cruise power setting that is appropriate for the flight conditions and consider the following: Lesson requirements Distance to travel Weather Aircraft limitations ATC clearance Reaching the desired cruise power setting, set the pitch and then trim so that zero pressure on the yoke is required to maintain the desired pitch attitude. 6-1 Instrument Flight The 5T’s of Instrument Flight (Time, Turn, Twist, Transition, Talk) The purpose of the 5T’s is to remind you to perform tasks that are necessary and critical to instrument flight. The 5T’s must be performed: At every fix, waypoint, and navigational aid. When beginning each turn in a hold. When entering and exiting a DME arc. After receiving a new clearance. When performing each of the 5T’s you must: Verbally call out what action is required. Do the action and call out that it has been completed (e.g. “Turn to heading 150). If the action is not necessary, call out that it is not necessary (e.g. “Turn not necessary”). TIME Time means to start or verify timing. Timing is required when performing holds, some approaches, and timed turns. TURN Turn means to change the aircraft heading to comply with a clearance, intercept or track a course, fly to a navigational aid, and verify that the present heading is correct. TWIST Twist means to change or verify the indicated course on the CDI. TRANSITION Transition means to descend, climb, or change airspeed as needed. TALK Talk means communicating as necessary with ATC or airport/practice area traffic. 6-2 Instrument Flight The STIMEE Check The purpose of the STIMEE check is to remind you to perform necessary tasks and is critical when flying an instrument approach procedure: SELECT Select means to select and load the instrument approach. TUNE Tune means to set and verify the correct communication and navigation frequencies. IDENTIFY Identify means to audibly verify the correct navigational aid is selected by listening to the Morse code. On G1000 aircraft, the navigational aid should be verified by its identifier shown next to the frequency. MARKERS Ensure the audio panel is set to identify marker beacons. ESTIMATE ENTRY Estimate how you will enter the approach or holding pattern. ESTIMATE WIND Estimate the need for wind correction. On G1000 aircraft, there is a magenta diamond near the top of the HSI known as the Current Track Indicator which will help you correct for wind. 6-3 Instrument Flight Instrument Briefings Before the top of descent, prepare for arrival at the airport using the following procedure which may be remembered with the mnemonic AABBC: ATIS Obtain weather information for the destination airport as soon as practical. ATC Contact ATC to request IAP or landing. If landing at uncontrolled airport, state position and intentions over the CTAF when 10 miles from airport. BUILD Configure avionics as necessary for the instrument or visual approach. BRIEF Brief the approach and landing, including any significant weather. If conducting an instrument approach, the following items should be included in the brief (see next page for illustration): 1. Expiration of the approach plate 2. Name of the approach and airport 3. Final approach course and frequency 4. Review notes section and ensure all frequencies are set 5. IAF name and altitude 6. FAF name and altitude 7. MDA or DA 8. MAP 9. Missed approach procedure CHECKLIST Perform the Approach Checklist prior to the initial approach fix (IAF). Perform Before Landing Checklist prior to reaching final approach fix (FAF). 6-4 Instrument Flight Instrument Briefings (cont.) Approach Briefing Visualized 2 3 4 9 5 6 8 7 6-5 Instrument Flight 1 Lost Communications Procedures 1. Troubleshoot Troubleshoot the failure by checking... Frequencies. Check volume. Ammeter: if required, follow the appropriate electrical malfunction checklist. Ensure the headset is plugged in. Check circuit breakers. Check if squelch is operable. Switch radios (COM 1 vs. COM 2). Switch to the last ATC frequency where communication was possible. Switch the headset jack from the currently used side to the opposite side (i.e. pilot to copilot) and use the mic button on the corresponding yoke or handheld mic. If not resolved, continue to step 2. 2. Assess Ask yourself: am I able to continue to a suitable airport in VFR conditions? If yes... Squawk 7600 if able. Remain in VFR conditions and land as soon as practical. If no... Squawk 7600 if able. Make appropriate route and altitude changes applicable to the requirements for lost communications in instrument meteorological conditions (IMC). 6-6 Instrument Flight Lost Communications in IMC 1. Route Select the route applicable to the flight with the mnemonic AVEF in sequential order and fly the first applicable route. A- Assigned If assigned a route from ATC proceed to step 2; if not, proceed to Vectored. V- Vectored If radar vectored, fly from the current position directly to the fix or the route given by ATC. Once reaching the fix, route, or airway specified in the clearance, apply AVEF again to determine the route from there and proceed to step 2. If not vectored, proceed to Expect. E- Expect In the absence of an assigned route, fly the ATC expected route. If no expected route is given, proceed to Filed. F- Filed In the event all of the above do not apply, fly the route that was originally filed on the flight plan. 2. Altitude Use the mnemonic MEA and select the highest of the following three altitudes for each segment of the route: M - Minimum IFR Altitude Minimum IFR altitude for the route segment that the airplane is on. This could be an MEA, MOCA, MCA, OROCA, MSA, or whatever the minimum published altitude is for the location. E - Expected This is the last altitude ATC told you to expect; do not change altitude until the time or fix which ATC told you to expect it by. A - Assigned The altitude assigned by ATC. 3. Arrival at the Clearance Limit Is the clearance limit a fix from which an approach begins? If yes... Start descent and approach as close as possible to the expect further clearance (EFC) time, or, if there is no EFC time assigned, start at the estimated time of arrival (ETA). (Proceed to step D on the next page). If no... If the clearance limit is the destination airport, proceed to step A on the next page. If the clearance limit is not the destination airport, proceed to step C on the next page. 6-7 Instrument Flight Lost Communications in IMC (cont.) Step A: If conditions such as MSA, OROCA, oxygen requirements, icing, and navigation equipment allow it; fly over the airport (proceed to Step C). OR If you determine it is not possible or reasonable to fly over the airport (proceed to Step B). Step B: Use your best judgement on how to proceed to a fix from which an approach begins. The descent and approach will be started as close as possible to the ETA (proceed to Step D). Step C: Leave the clearance limit as close as possible to the EFC, and fly to a fix from where an approach begins. The descent and approach will be started at the ETA (proceed to Step D). OR If no EFC has been given, when the aircraft arrives over your clearance limit, keep flying, and continue past the clearance limit to a fix from which an approach begins. Once reaching a fix from which an approach begins, the descent and approach will be started as close as possible to the ETA (proceed to Step D). Step D: If you arrive at the clearance limit early, hold as depicted, or, if no holding pattern is depicted, hold on the course on which you arrived at the fix in a standard pattern until the EFC/ETA, or if it applies, hold on the procedure turn side of the FAC and descend to the published altitude before continuing on the approach. If it is necessary to loose altitude to descend to the initial approach altitude, remain in the depicted holding pattern and descend to the initial approach altitude before continuing to land (proceed to step 4). 4. Submit NASA Report It is not possible to provide procedures for every lost communications failure situation. If you encounter a scenario or situation which cannot be resolved using the above procedures you should consider it an emergency when in IFR conditions. In this situation, you should squawk 7700 and use your best judgement to decide an appropriate action for the circumstances. 6-8 Instrument Flight Precision Approach Procedures 1. Once given an expected approach: Configure aircraft: approximately 90 KIAS (2100-2300 RPM), flaps 0°. Complete AABBC Check. STIMEE Check. 2. Arriving at the IAF. Perform 5 T’s. Time: N/A. Turn: published approach course. Twist: verify CDI is set to next published course. Transition: set power to approximately 1700-1900 RPM to begin descent to the published glide slope intercept at 90 KIAS with approximate pitch down to 2-4° to descend 500-800 FPM or comply with ATC instructions. Review IAP to verify position, altitude, name of the next fix, and altitude after the next fix. 3. At glideslope (GS) intercept altitude. Level off. Set power for 90 KIAS (2100-2300 RPM). Announce when GS is alive. Complete Before Landing Checklist. Announce when glideslope intercept altitude until the FAF. Review IAP to verify position, altitude, name of the next fix, and altitude after the next fix. 4. When 1 dot below glideslope, perform 5 T’s. Time: not necessary on precision approach. Turn: should be established on final approach course. Twist: CDI matches final approach course. Transition: set power to approximately 1700-1900 RPM, pitch to track glideslope down to DA at 90 KIAS (assuming 3° glideslope, approximate descent can be calculated by groundspeed * 5 (e.g. 90 KTS groundspeed * 5 = approximately 450 FPM to maintain glideslope)). Talk: as required. 5. Track localizer and glideslope to DA. Track the localizer course by keeping the vertical CDI needle centered. When the needle is centered, set heading so that the track displayed on the GPS matches the localizer course. If off course, make heading corrections of 2° to 5° until the needle is centered. Use smaller corrections closer to the runway. Track the glideslope by keeping the horizontal CDI needled centered. If high or low on the glideslope use small pitch changes 1° to 2° to increase or decrease the rate of descent until the needle is centered. Once on glideslope, resume the required descent rate. Maintain 90 KIAS by making small power changes (less than 200 RPM). While descending to the DA, make 1000’, 500’, and 100’ callouts to minimums. 6-9 Instrument Flight Precision Approach Procedures (cont.) 6. Approaching Decision Altitude (DA) If the instructor or examiner asks you to remove your view limiting device: Remove device, look for runway, and announce “runway in sight.” Slowly reduce power to idle. Add flaps slowly to avoid ballooning. Approaching 65 KIAS, increase power to 1500 RPM. Pitch for the aim point and maintain the glideslope. Continue with normal landing procedure. OR If the instructor or examiner does not ask you to remove your view limiting device: At the DA, announce “minimums, missed approach.” Perform go-around and follow missed approach procedure. 1. Prior to the initial approach fix (IAF) Configure aircraft AABBC Check STIMEE Check 2. Arriving at the IAF Perform 5 T’s 3. GS Intercept Altitude Level off and maintain 90 KIAS Before Landing Checklist Report GS Alive 4. 1 Dot Below GS 1 Perform 5 T’s Power approx. 17001900 RPM 5. Track GS and horizontal guidance to DA Maintain proper descent rate Maintain 90 KIAS 6. Decision Altitude Continue to land or begin missed approach 6-10 Instrument Flight Non-Precision Approach Procedures 1. Once given an expected approach: Configure aircraft: approximately 90 KIAS (2100-2300 RPM), flaps 0°. AABBC Check. STIMEE Check. 2. Arriving at the IAF Perform 5 T’s. Time: N/A. Turn: published approach course. Twist: CDI to next published course. Transition: set power to approximately 1700-1900 RPM to begin descent to the published stepdown altitude at 90 KIAS with approximate pitch down to 2-4° to descent 500-800 FPM. Review IAP to verify position, altitude, name of the next fix, and altitude after the next fix. 3. Reaching stepdown altitude Level off. Set power to 90 KIAS (2100-2300 RPM). Maintain published altitude until next stepdown fix or FAF. Complete Before Landing Checklist prior to FAF. Review IAP to verify position, altitude, name of the next fix, and altitude after the next fix. 4. Arriving at FAF: Complete 5 T’s Time: as required. Turn: should be established on final approach course. Twist: CDI matches final approach course. Transition: set power to approximately 1700-1900 RPM, pitch to descend down to MDA at 90 KIAS around 500-800 FPM. Talk: as required. 5. Track localizer and glideslope to DA Track the final approach course by keeping the vertical CDI needle centered. When the needle is centered, set heading so that the track displayed on the GPS matches the final approach course. If off course, make heading corrections of 2° to 5° until the needle is centered. Use smaller corrections closer to the runway. Maintain 90 KIAS by making small power changes (less than 200 RPM). While descending to the MDA, make 1000’, 500’, and 100’ callouts to minimums. 6. At the MDA Level off and set power to maintain 90 KIAS (2100-2300 RPM). Continue to the Missed Approach Point (MAP). If you do not have the runway in sight prior to the visual descent point (VDP), expect to execute the missed approach procedure at the MAP. 6-11 Instrument Flight Non-Precision Approach Procedures (cont.) 7. Arriving at the VDP or MAP If the instructor or examiner asks you to remove your view limiting device: Remove device, look for runway, and announce “runway in sight.” Slowly reduce power to idle. Add flaps slowly to avoid ballooning. Approaching 65 KIAS increase power to 1500 RPM. Pitch for the aim point and maintain the glideslope. Continue with normal landing procedure. OR If the instructor or examiner does not ask you to remove your view limiting device: Remain at MDA until arriving at MAP. At MAP, announce “minimums, missed approach.” Perform go-around and follow missed approach procedure. 1. Prior to the initial approach fix (IAF) Configure aircraft AABBC Check STIMEE Check 3. Reaching the Stepdown altitude Level off Maintain 90 KIAS (approx. 2100-2300 RPM) Complete Before Landing Checklist 2. Arriving at the IAF Perform 5 T’s Begin descent to the published stepdown altitude 5. Track Final Approach Course to MAP 4. FAF Perform 5 T’s Maintain 90 KIAS (approx. 1700-1900 RPM) Descend to MDA (approx. 500-800 FPM) 6. MDA Level off Maintain 90 KIAS (approx. 2100-2300 RPM) 7. Approaching VDP or MAP Runway in sight: continue with normal landing Runway not in sight: remain at MDA until MDA then execute MAP Hold as Published at Fix Missed Approach Procedure 6-12 Instrument Flight Circling Approach Procedures 1. When 1 NM from the runway (not exceeding 1.3 NM) Align the airplane with the downwind leg. Comply with published traffic pattern direction. Maintain 90 KIAS (2100-2300 RPM). Maintain MDA +100'/-0'. 2. Abeam touchdown point Use aiming point markers as an aim point if available. Reduce throttle to 1500-1700 RPM, flaps 10°. Establish 80 KIAS. 3. 45° past the touchdown point Begin base leg. Flaps 20°. Establish 75 KIAS. 4. Continue with normal landing procedures Flaps 30°. Establish stabilized approach at 65 KIAS. NOTE Maintain MDA +100'/-0' until the airplane is in a continuous position to land using a normal descent rate and normal maneuvers. This is typically when the airplane is base-to-final. During a circling approach, you must immediately begin a missed approach “whenever an identifiable part of the airport is not distinctly visible to the pilot during a circling maneuver at or above MDA, unless the inability to see an identifiable part of the airport results only from a normal bank of the aircraft during the circling approach” (14 CFR 91.175). 6-13 Instrument Flight Circling Approach Procedures (cont.) 3. 45° Past touchdown point Begin base leg Flaps 20° Establish 75 KIAS 2. Abeam touchdown point Throttle 1500-1700 RPM Flaps 10° Establish 80 KIAS 1. Approx. 1 NM from RWY Enter downwind Maintain MDA 90 KIAS (2100-2300 RPM) 1. Approx. 1 NM from RWY Enter downwind Maintain MDA 90 KIAS (2100-2300 RPM) 4. Final Flaps FULL Establish 65 KIAS 3. 45° Past touchdown point Begin base leg Flaps 20° Establish 75 KIAS 2. Abeam touchdown point Throttle 1500-1700 RPM Flaps 10° Establish 80 KIAS 6-14 Instrument Flight Holding Procedures 1. Write down and read back clearance 2. Set avionics Select direct to fix in the GPS (Magenta), NAV (Green) needles, or DME/Bearing Pointer Distance. Tune and identify VOR, fix, or waypoint and center the CDI with a TO indication. Turn direct to the fix by using GPS (Magenta) or use NAV (Green) needles. Determine hold entry. 3. Configure aircraft When less than 3 minutes from the holding fix, slow to 90 KIAS (2100-2300 RPM). 4. Cross the fix, turn to entry course After passing the fix (TO/FROM flag flip or DME distance is met), perform 5 T’s. Turn: fly the proper entry. Parallel or direct entry = Outbound course. Teardrop entry = Outbound course +/- 30° (LARS: Left, Add; Right, Subtract). Time: start timer if on a timed hold. Twist: verify CDI set to inbound course. Transition: verify 90 KIAS (2100-2300 RPM, or if descending in hold, 1700-1900 RPM). Talk: report reaching the holding fix, altitude, and time. 5. After 1 minute or DME distance is met, turn inbound Perform 5 T’s. Turn: Direct or teardrop entry: turn to inbound course. Parallel entry: to heading to intercept inbound course. Time: start time when wings level or at assigned DME distance. Twist: verify CDI is set to inbound course. Transition: verify 90 KIAS (2100-2300 RPM). Talk: as required. 6. Continue holding until next clearance is received Each time you turn inbound or outbound, perform 5 T’s. Turn: to inbound or outbound course +/- the wind correction angle on the inbound leg (i.e. inbound leg WCA = 5°, then outbound leg WCA = 15° into the wind). Time: start timer when abeam fix or wings level. The outbound leg should be adjusted so that the inbound leg is 1 minute long (not necessary if in a DME distance hold). When in a headwind outbound, add 1 second for every knot of headwind. When in a tailwind outbound, double every knot of tailwind and subtract that time from 1 minute. Twist: verify CDI is set to inbound course. Transition: verify 90 KIAS (2100-2300 RPM). Talk: as required. 7. Depart the hold Write down and readback the next clearance. Turn to the departure heading. Configure aircraft as necessary to comply with the clearance. If no further clearance is given by EFC time, ask ATC for further instructions. Report leaving the holding fix. 6-15 Instrument Flight Holding Procedures Direct Entry (VOR Hold) Example holding instructions for graphic below: “K-State 44, hold west of the SLN VORTAC on the 250 radial, maintain 5000, expect further clearance at 00:00 Zulu, current time 23:45 Zulu” 6-16 Instrument Flight Holding Procedures Teardrop Entry (GPS Hold) Example holding instructions for graphic below: “K-State 53, hold north of ANTON on the 330 radial, maintain 3300, expect further clearance at 16:00 Zulu, current time 15:36 Zulu.” 6-17 Instrument Flight Holding Procedures Parallel Entry (DME Hold) Example holding instructions for graphic below: “K-State 39, hold northwest of the 10 DME fix on the 310 radial from the SLN VORTAC, 5 mile legs, maintain 7000, expect further clearance at 18:00 Zulu, current time 17:12 Zulu.” 6-18 Instrument Flight Arc Intercept Procedures 1. Write down and readback clearance “K-State 49, turn left heading 300, join the west 7 DME arc for the VOR 17 approach into Salina.” ATC has provided the following: Intercept heading: 300 DME arc radius: 7 NM NAVAID to perform arc from: SLN VORTAC To comply with the clearance, the airplane must intercept the SLN 7 DME arc while on a heading of 340 and fly the arc until turning inbound on the final approach course. 2. Turn to the assigned heading or intercept assigned radial ATC may clear you to join the arc from a heading or by tracking a radial to the arc; turn as necessary to comply with the clearance. 3. Set avionics If using NAV (green) needles: Tune and identify the NAVAID. Enable bearing pointers by selecting “PFD” or “PFD Opt” softkey on the primary flight display and selecting the “Bearing 1” or “Bearing 2” softkey to “call up” the appropriate bearing pointer for distance information. Center CDI with a TO indication to provide the bearing the aircraft is presently on and will help calculate the initial heading to get established on the arc. If using GPS: In the Flight Plan menu, select the DME arc, then select Activate Leg. Follow GPS instructions to fly the arc. 4. 0.5 DME from the arc, lead turn into the arc and perform 5 T’s Turn: initial turn will be to a heading that is 90° from the present bearing and in the direction of the arc Time: not necessary Twist: center CDI when established on the arc Throttle: maintain 90 KIAS (2100-2300 RPM) Talk: not necessary unless instructed by ATC 6-19 Instrument Flight Arc Intercept Procedures (cont.) 5. Turn 10 - Twist 10 or Bearing Pointer Method Turn 10 - Twist 10 Center CDI with a TO indication. Twist CDI 10° in the direction of the arc (course should be in front of the airplane). Turn aircraft 10° in the direction of the arc. As the CDI centers, continue to twist the course 10° and turn the aircraft 10° (as required to maintain correct distance from the NAVAID) until you intercept the end radial or final approach course. The actual headings and flight path around the VOR will look like this: HDG 050 CDI 140 HDG 040 CDI 130 HDG 030 CDI 120 HDG 020 CDI 110 HDG 010 CDI 100 HDG 360 CDI 090 HDG 350 CDI 080 <-260R HDG 300 Bearing Pointer Method Maintain 90° from the station by placing the head of the bearing pointer on the left or right 90° mark on the heading indicator. If DME increases: turn the airplane so that the head of the bearing pointer rises above the left or right 90° mark on the heading indicator. If DME decreases: turn the airplane so that the head of the bearing pointer falls below the left or right 90° mark on the heading indicator. As the DME returns to the desired amount, turn the airplane so that the head of the bearing pointer is on the left or right 90° mark on the heading indicator. Make small corrections (no more than 30° either direction for the bearing pointer). 6. Exit the arc as specified by ATC or examiner 6-20 Instrument Flight
0
You can add this document to your study collection(s)
Sign in Available only to authorized usersYou can add this document to your saved list
Sign in Available only to authorized users(For complaints, use another form )