SPEAKER SWITCHING CIRCUIT - NFPA STYLE W
SPEAKERS MUST BE LISTED FOR FIRE PROTECTION. REFER
TO THE RELAY CONTACT RATING TABLE FOR MAXIMUM LOAD.
CONTROL
MODULE
9
)–(
67 8 9
5
10
11
8 43
12
13
2
7 TENS1 0 15 14
6789
6 45
)–(
5
3
2
0
1
2
)–(
)+(
3
)+(
ADDRESS
SUPERVISION
)+(
FCM-1 Supervised Control Module
Installation And Maintenance Instructions
Specifications
Normal Operating Voltage:
Maximum Current Draw:
Average Operating Current:
mode)
AUDIO CIRCUIT
DO NOT LOOP WIRE AROUND TERMINALS
3 & 4. BREAK WIRE TO ENSURE
SUPERVISION OF CONNECTIONS.
)–(
AUDIO AMPLIFIER, 70.7 Vrms MAX.
4
10
ONES
LOOP
)+(
CONNECT
MODULES
TO LISTED
COMPATIBLE
CONNECT
MODULES
TO LISTED
COMPATIBLE
NOTIFIER
CONTROL
PANELS
NOTIFIER
CONTROL
PANELS
ONLYONLY
)–(
FROM PANEL OR
)+( PREVIOUS DEVICE
)–(
)+(
TO NEXT
DEVICE
47 K EOL
RESISTOR
ELR-47K
WIRES MUST BE SUPERVISED PER NFPA
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
ALL WIRING SHOWN IS SUPERVISED.
I56-1169-013
Figure 5. Typical wiring for speaker supervision and switching, NFPA Style Y:
USE ONLY MODELS AA-30, AA100 OR AA-120. AMPLIFIER
MUST PROVIDE WIRING SUPERVISION PER NFPA.
AUDIO CIRCUIT WIRING MUST BE TWISTED PAIR AS A MINIMUM.
SEE NOTIFIER INSTALLATION MANUAL FOR DETAILED INFORMATION.
ALL TERMINAL WIRING IS POWER LIMITED.
MODULE POLARITIES ARE
SHOWN IN ALARM
TO NEXT CONTROL MODULE
LAST MODULE MUST RETURN
WIRES FOR SUPERVISION
Maximum NAC Line Loss:
External Supply Voltage:
Maximum (NAC):
Maximum (Speakers):
Drain on External Supply:
Max NAC Current Ratings:
C0879-01
Temperature Range:
Humidity:
Dimensions:
Accessories:
ALL WIRING SHOWN IS SUPERVISED.
TO NEXT
DEVICE
CONTROL
MODULE
SPEAKERS MUST BE LISTED FOR FIRE PROTECTION. REFER
TO THE RELAY CONTACT RATING TABLE FOR MAXIMUM LOAD.
9
47 K EOL
RESISTOR
IS INTERNAL
AT TERMINALS
8 AND 9
8
)–(
5
4
3
2
67 8 9
10
11
12
13
7 TENS1 0 15 14
)–(
6
5
LOOP
)+(
6789
5
4
3
2
10
ONES
0
1
2
)–(
)+(
3
4
ADDRESS
)+(
BYPASS CAPACITORS : 100
A2143-20 NONPOLARIZED
<10 A LEAKAGE
MODULE POLARITIES ARE
SHOWN IN ALARM
WIRES MUST BE SUPERVISED PER NFPA
CONNECT MODULES TO LISTED COMPATIBLE
NOTIFIER CONTROL PANELS ONLY
)–(
FROM PANEL OR
)+( PREVIOUS DEVICE
)–(
)+(
485µA Max. (LED flashing, NAC shorted)
4 VDC
(between Terminals T3 and T4)
Regulated 24 VDC
70.7 V RMS, 50 W
1.7 mA Maximum using 24 VDC supply; 2.2 mA Maximum using 80 VRMS supply
For class B wiring system, the current rating is 3A
For class A wiring system, the current rating is 2A
32°F to 120°F (0°C to 49°C)
10% to 93% Non-condensing
41/2˝ H × 4˝ W × 11/4˝ D (Mounts to a 4˝ square by 21/8˝ deep box.)
SMB500 Electrical Box; CB500 Barrier
Before Installing
This information is included as a quick reference installation guide. Refer to the control panel installation manual for
detailed system information. If the modules will be installed in an existing operational system, inform the operator and
local authority that the system will be temporarily out of service. Disconnect power to the control panel before installing
the modules.
Figure 6. Typical fault tolerant wiring for speaker supervision and switching, NFPA Style Z:
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
15 to 32 VDC
6.5 mA (LED on)
375µA (LED flashing - in group poll mode) 350µA (LED of flashing - in direct poll
NOTICE: This manual should be left with the owner/user of this equipment.
AUDIO CIRCUIT
DO NOT LOOP WIRE AROUND TERMINALS
3 & 4. BREAK WIRE TO ENSURE
SUPERVISION OF CONNECTIONS.
)–(
AUDIO AMPLIFIER, 70.7 Vrms MAX.
USE ONLY MODELS AA-30, AA100 OR AA-120. AMPLIFIER
)+(
MUST PROVIDE WIRING SUPERVISION PER NFPA.
SUPERVISION
AUDIO CIRCUIT WIRING MUST BE TWISTED PAIR AS A MINIMUM.
SEE NOTIFIER INSTALLATION MANUAL FOR DETAILED INFORMATION.
ALL TERMINAL WIRING IS POWER LIMITED.
TO NEXT CONTROL MODULE
LAST MODULE MUST RETURN
WIRES FOR SUPERVISION
General Description
FCM-1 Supervised Control Modules are intended for use in intelligent, two-wire systems, where the individual address of
each module is selected using the built-in rotary switches. This module is used to switch an external power supply, which
can be a DC power supply or an audio amplifier (up to 80 VRMS), to notification appliances. It also supervises the wiring
to the connected loads and reports their status to the panel as NORMAL, OPEN, or SHORT CIRCUIT. The FCM-1 has two
pairs of output termination points available for fault-tolerant wiring and a panel-controlled LED indicator. This module can
be used to replace a CMX-2 module that has been configured for supervised wiring operation.
Compatibility Requirements
To ensure proper operation, this module shall be connected to a compatible Notifier system control panels only (list available from Notifier).
Mounting
The FCM-1 mounts directly to 4˝ square electrical boxes (see Figure 2A). The box must have a minimum depth of 21/8˝.
Surface mounted electrical boxes (SMB500) are available.
C0880–01
WARNING
All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed)
state during shipping. To ensure that the switch contacts are in their correct state, modules must be made to communicate
with the panel before connecting circuits controlled by the module.
N500-46-00
4
I56-1169-013
© 2006 Notifier
N500-46-00
1
I56-1169-013
Notifier, 12 Clintonville Rd., Northford, CT 06472
Wiring
NOTE: All wiring must conform to applicable local codes, ordinances, and regulations. When using control modules in
nonpower limited applications, the CB500 Module Barrier must be used to meet UL requirements for the separation of
power-limited and nonpower-limited terminals and wiring. The barrier must be inserted into a 4˝ × 4˝ × 21/8˝ junction
box, and the control module must be placed into the barrier and attached to the junction box (Figure 2A). The powerlimited wiring must be placed into the isolated quadrant of the module barrier (Figure 2B).
Figure 3. Typical notification appliance circuit configuration, NFPA Style Y:
1. Install module wiring in accordance with the job drawings and appropriate wiring diagrams.
2. Set the address on the module per job drawings.
Note: Some panels support extended addressing. In order to set the module above address 99 on compatible systems,
carefully remove the stop on the upper rotary switch with thumb in the direction shown in Figure 1A.
3. Secure module to electrical box (supplied by installer), as shown in Figure 2A.
TO NEXT
DEVICE
IMPORTANT: When using the FCM-1 for fire fighter telephone applications, remove Jumper (J1) and discard. The Jumper
is located on the back under the product label as shown in Figure 1B. The module does not provide ring back when used
as a firefighter telephone circuit.
MODULE POLARITIES ARE
SHOWN IN ALARM
)-(
)-(
Figure 1A. Removing rotary switch stop:
Figure 1B. Jumper location:
ONES
LOOP
)-(
)+(
9
0
8
1
67 8 9
5
10
11
4
3
12
13
2
1
7 TENS 0 15 14
6789
5
6 4
3
5 21
0
47K EOL
RESISTOR
ELR-47K
ONES
LOOP
)+(
67 8 9
5
10
11
8 43
12
13
2
7 TENS1 0 15 14
6789
6 45
3
5 21
0
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
FROM PANEL OR
PREVIOUS DEVICE
24 VDC CIRCUIT
DO NOT LOOP WIRE ON TERMINALS
3 & 4. BREAK WIRE RUN TO PROVIDE
SUPERVISION OF CONNECTIONS.
)-(
)+(
2
ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED
)-(
)+(
CONTROL
MODULE
UL LISTED EOL RELAY
SHOWN ENERGIZED
24 VDC COIL
EOLR-1
9
SIGNAL LINE CIRCUIT (SLC)
CONNECT MODULES TO LISTED COMPATIBLE
NOTIFIER CONTROL PANELS ONLY
)-(
)+(
3
4
ADDRESS
)+(
24 VDC POWER SUPPLY
ISOLATED, REGULATED, POWER
LIMITED PER NFPA 70.
LISTED FOR FIRE PROTECTION WITH
BATTERY BACKUP.
TO NEXT CONTROL MODULE OR END-OF-LINE-RELAY.
ONE RELAY REQUIRED FOR EACH CIRCUIT.
SOME CONTROL PANELS HAVE RELAY BUILT IN AND
DO NOT REQUIRE EXTERNAL WIRING. REFER TO
NOTIFIER MANUAL.
0
C0820-01
1
BACK OF
MODULE
2
3
LABEL
4
ADDRESS
Figure 4. Typical fault tolerant notification appliance circuit configuration, NFPA Style Z:
C0218-00
J1 UNDER LABEL
Figure 2A. Module mounting with barrier:
C0458-00
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
ALL WIRING SHOWN IS SUPERVISED
AND POWER LIMITED
Figure 2B:
TO NEXT
DEVICE
CONNECT MODULES TO LISTED COMPATIBLE
NOTIFIER CONTROL PANELS ONLY
)–(
)–(
)+(
)+(
FROM PANEL OR
PREVIOUS DEVICE
CONTROL
MODULE
MODULE POLARITIES ARE
SHOWN IN ALARM
9
8
LO
OP
8
9
4 5 6 78
3
9
10
EN 21
S 0
1 11
1
4 5 6 7 8 5 14 13 2
3
9
ON
2
ES 1
0
AD
DR
ES
S
5
6
7T
4
3
2
1
EOL RESISTOR IS
INTERNAL AT
TERMINALS 8 & 9
0
)–(
LO
OP
8
9
4 5 6 78
3
9
TEN 2
10
S 10
1211
15
4 5 6 7 8 14 13
3
9
ON
2
ES 1
0
AD
DR
ES
S
5
6
7
4
3
2
1
0
ISOLATED
QUADRANT
)–(
6
5
LOOP
)+(
UL LISTED EOL RELAY
SHOWN ENERGIZED
24VDC COIL
EOLR-1
5
4
3
2
67 8 9
10
11
12
13
7 TENS1 0 15 14
6789
5
4
3
2
10
ONES
0
)–(
)+(
1
2
3
4
ADDRESS
)+(
24 VDC CIRCUIT
DO NOT LOOP WIRE ON TERMINALS
3 & 4. BREAK WIRE RUN TO PROVIDE
SUPERVISION OF CONNECTIONS.
)–(
)+(
24 VDC POWER SUPPLY
ISOLATED, REGULATED, POWER
LIMITED PER NFPA 70.
LISTED FOR FIRE PROTECTION WITH
BATTERY BACKUP.
TO NEXT CONTROL MODULE OR END-OF-LINE-RELAY.
ONE RELAY REQUIRED FOR EACH CIRCUIT.
SOME CONTROL PANELS HAVE RELAY BUILT IN AND
DO NOT REQUIRE EXTERNAL WIRING. REFER TO
NOTIFIER MANUAL.
C0821-01
C0219-00
C0217-00
N500-46-00
2
I56-1169-013
N500-46-00
3
I56-1169-013