DAVAO ORIENTAL STATE UNIVERSITY
FACULTY OF COMPUTING, DATA SCIENCE, ENGINEERING & TECHNOLOGY
BS IN CIVIL ENGINEERING
CE 121 FUNDAMENTALS OF SURVEYING
FIELDWORK No. 2: TAPING OVER SMOOTH AND LEVEL GROUND
1. Objective:
a. To determine the horizontal length of a line over a smooth and level ground with the tape
supported throughout its length
2. Instruments & accessories:
a. Steel tape (preferably 30 m or 50 m steel tape)
b. Range poles
c. Pegs
d. Markers (paint, stone, hubs etc.)
3. Location
a. DORSU Main Ground
4. Procedure
In taping, there are 2 tapemen, the forward or front tapeman and the rear tapeman. A thid may act as a
recorder or clearing man. If there are only 2 performing the taping, the rear tapeman shall act as
recorder.
a. Both front and rear tapemen count the number of pins, a set being 11 pins. One is left with the
rear tapeman, while the 10 pins are brought forward along the line by the front tapeman who also
drags the tape holding the zero end. When the tape is about to be fully unrolled from the reel, the
rear tapeman shouts “tape” to warn the front tapeman to stop.
b. The front tapeman then stays to one side of the line and waits for an alignment signal from the
rear tapeman. The rear tapeman aligns the pin held by the front tapeman by waving his rights
hand towards the right with the palm towards direction of motion, or with the left hand for a left
motion. Long waves mean fast movement, and short waves mean slow motion. When the front
pin or range pole is on the line, the rear tapeman shows either hand palm forward and waves in
front, notifying the front tapeman for correct alignment.
c. The front tapeman now faces the rear tapeman. Rear tapeman places the end graduation of the
tape on the point behind and shouts “all right here”. Front tapeman pulls the tape about 10lbs,
transfer the pin at the zero mark and shouts back “all right”. The rear tapeman drops the rear end
of the tape, picks up the pin and shouts “forward”. Similar procedure is continued until no more
pin is left with the front tapeman.
d. The front tapeman now waits for the rear tapeman to catch up with him and they both count the
number of pins, the eleventh pin on the ground not included. One tally is then recorded.
e. Repeat the procedure until the last full tape length before the end of the line.
M.RANGEL
1
f. The fractional tape length is measured by placing a full meter-mark against the last pin with the
end of the line contained within the first fractional or graduated meter (from zero mark to 1m
mark). That portion of the tape which protrudes beyond the end of the line is then subtracted from
the full meter-mark opposite the last pin.
g. After the measure of the whole line is completed, a second measurement should be made along
the opposite direction. The mean of the two measurements is taken as the most probable value of
the length of the line.
IMPORTANT NOTES:
There are 2 important properties of a line namely: Direction and Distance. The most common
method of measuring distances is by taping or chaining. Hence the beginner must endeavor to put
emphasis on this field procedure to achieve speed and accuracy in measurements of distances.
When long tapes are used especially during windy days, the following procedure is suggested:
When alignment is given, front tapeman faces rear tapeman. Automatically, rear tapeman puts
end mark against point, while front tapeman pulls the tape and transfers the front marking pin at
zero mark. He then suddenly releases pressure on tape, thus notifying the rear tapeman that
measurement has been made. No shouting then is necessary with this procedure which is very
useful in professional survey field practice.
5. Observation Sheets/ Data
6. Computation
The acceptable precision should be at least 1/1000 whenever possible. If not attained, repeat the
measurement.
7. Illustration/ Sketch
a. Draw a detailed sketch of the polygon and surrounding area with each point of the polygon
labeled.
M.RANGEL
2
8. Remarks and Conclusion
Refer to the sample notes
M.RANGEL
3