9. Constrained motion of connected particles
2/31. The deceleration of the mass center 𝐺𝐺 of a car during a crash test is measured by an
accelerometer with the results shown, where the distance 𝑥𝑥 moved by 𝐺𝐺 after impact is 0.8 m.
Obtain a close approximation to the initial impact velocity 𝑣𝑣 from the data given.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 7th ed., John Wiley & Sons, Inc., 2012. Problem 2/31 ]
𝑣𝑣𝑣𝑣𝑣𝑣 = 𝑎𝑎𝑎𝑎𝑎𝑎
0
1 2
𝑣𝑣 2
2
� 𝑣𝑣𝑣𝑣𝑣𝑣 = 0 − 𝑣𝑣 = −
2
2
𝑣𝑣
0.8
� 𝑎𝑎𝑎𝑎𝑎𝑎 = 𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴 𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢𝑢 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 = 0.8 −6𝑔𝑔 +
0
𝑣𝑣 2
−
= −58.86 →
2
1
0.6 −4𝑔𝑔 = −58.86 𝑚𝑚/𝑠𝑠 2
2
𝑣𝑣 = 10.85 𝑚𝑚/𝑠𝑠 = 39.06 𝑘𝑘𝑘𝑘/ℎ𝑟𝑟
∗ 𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷
1
2/158. During a portion of a vertical loop, an airplane flies in an arc of radius 𝜌𝜌 = 600 m with a
constant speed 𝑣𝑣 = 400 km/h. When the airplane is at 𝐴𝐴, the angle made by 𝑣𝑣 with the
horizontal is 𝛽𝛽 = 30°, and radar tracking gives 𝑟𝑟 = 800 m and 𝜃𝜃 = 30°. Calculate 𝑣𝑣𝑟𝑟 , 𝑣𝑣𝜃𝜃 , 𝑎𝑎𝑟𝑟 ,
and 𝜃𝜃̈ for this instant.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 7th ed., John Wiley & Sons, Inc., 2012. Problem 2/158 ]
1,000
= 111.11 𝑚𝑚/𝑠𝑠
𝑣𝑣 = 400
3,600
𝜌𝜌 = 600 𝑚𝑚,
𝑛𝑛
𝑛𝑛
𝑎𝑎
𝑎𝑎
𝑡𝑡
𝑣𝑣
𝑟𝑟
30° 30°
30°
30°
𝑣𝑣
𝑡𝑡
𝜃𝜃
𝜔𝜔 = 𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶 → 𝛼𝛼 = 0, 𝑎𝑎𝑡𝑡 = 0 𝑚𝑚/𝑠𝑠 2
𝑛𝑛
𝑡𝑡
𝑣𝑣 2 111.112
=
= 20.58 𝑚𝑚/𝑠𝑠 2
𝑎𝑎 = 𝑎𝑎𝑛𝑛 =
𝜌𝜌
600
𝑣𝑣𝑟𝑟 = 𝑟𝑟̇ = 𝑣𝑣 � 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 = 96.22 𝑚𝑚/𝑠𝑠
𝑟𝑟 = 800 𝑚𝑚
𝑣𝑣𝜃𝜃 = 𝑟𝑟𝜃𝜃̇ = 𝑣𝑣 � 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠 = 55.56 𝑚𝑚/𝑠𝑠
𝑎𝑎𝑟𝑟 = 𝑟𝑟̈ − 𝑟𝑟𝜃𝜃̇ 2 = 𝑎𝑎 � 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 = 10.29 𝑚𝑚/𝑠𝑠 2
𝑎𝑎𝜃𝜃 = 𝑟𝑟𝜃𝜃̈ + 2𝑟𝑟̇ 𝜃𝜃̇ = −𝑎𝑎 � 𝑠𝑠𝑠𝑠𝑠𝑠60 = −17.82 𝑚𝑚/𝑠𝑠 2
→ 𝜃𝜃̈ =
−17.82 − 2𝑟𝑟̇ 𝜃𝜃̇
𝑟𝑟
𝜃𝜃̇ =
𝜃𝜃̈ =
𝑟𝑟̇ = 96.22 𝑚𝑚/𝑠𝑠
55.56
= 0.06945 𝑟𝑟𝑟𝑟𝑟𝑟/𝑠𝑠
800
−17.82 − 2(96.22)(0.06945)
800
= −0.039 𝑟𝑟𝑟𝑟𝑟𝑟/𝑠𝑠 2
2
2/193. While running toward the sideline at a speed 𝑣𝑣𝑄𝑄 = 7 m/s, the football quarterback 𝑄𝑄
throws a pass to the stationary receiver 𝑅𝑅. The speed of the ball relative to the quarterback is
18 m/s. Treat the problem as two-dimensional.
1) At what angle 𝛼𝛼 should the quarterback release the ball?
2) Determine the speed of the ball.
[ Adapted from Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 7th ed., John Wiley & Sons, Inc., 2012. Problem 2/193 ]
𝑣𝑣𝑄𝑄
𝜃𝜃
𝛽𝛽
𝑣𝑣𝐵𝐵
𝑣𝑣𝐵𝐵/𝑄𝑄
𝜃𝜃 = tan−1
𝛼𝛼
12
= 71.57°
4
𝑣𝑣⃑𝐵𝐵 = 𝑣𝑣⃑𝑄𝑄 + 𝑣𝑣⃑𝐵𝐵/𝑄𝑄
𝑣𝑣𝐵𝐵/𝑄𝑄
𝑣𝑣𝑄𝑄
7(𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠.57)
=
→ 𝛼𝛼 = sin−1
= 21.65°
𝑠𝑠𝑠𝑠𝑠𝑠𝛼𝛼 𝑠𝑠𝑠𝑠𝑠𝑠𝜃𝜃
18
𝛽𝛽 = 180 − 71.57 − 21.65 = 86.78°
𝜃𝜃
𝑣𝑣𝐵𝐵/𝑄𝑄
𝑣𝑣𝐵𝐵
=
𝑠𝑠𝑠𝑠𝑠𝑠𝛽𝛽 𝑠𝑠𝑠𝑠𝑠𝑠𝜃𝜃
18(𝑠𝑠𝑠𝑠𝑠𝑠86.78)
𝑣𝑣𝐵𝐵 =
= 18.94 𝑚𝑚/𝑠𝑠
𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠.57
3
2/220. The power winches on the industrial scaffold enable it to be raised or lowered. For
rotation in the senses indicated, the scaffold is being raised. If each drum has a diameter of
200 mm and turns at the rate of 40 rev/min, determine the upward velocity 𝑣𝑣 of the scaffold.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 7th ed., John Wiley & Sons, Inc., 2012. Problem 2/220 ]
𝐿𝐿1 = 𝑙𝑙1 + 2 𝑙𝑙1 − 𝑙𝑙2 − ∆ + 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐
𝐿𝐿̇ 1 = 3𝑙𝑙1̇ − 2𝑙𝑙2̇ = −𝜔𝜔𝑟𝑟𝑑𝑑𝑑𝑑𝑑𝑑𝑑𝑑
𝑙𝑙1
𝐿𝐿2 = 𝑙𝑙1 − ∆ + 𝑙𝑙2
𝐿𝐿̇ 2 = 𝑙𝑙1̇ + 𝑙𝑙2̇ = 0 → 𝑙𝑙1̇ = −𝑙𝑙2̇
3𝑙𝑙1̇ − 2(−𝑙𝑙1̇ ) = −𝜔𝜔𝑟𝑟𝑑𝑑𝑑𝑑𝑑𝑑𝑑𝑑
4.19 0.1
𝑙𝑙1̇ = −
= −0.0838 𝑚𝑚/𝑠𝑠
5
𝑣𝑣 = −𝑙𝑙1̇ = 0.0838 𝑚𝑚/𝑠𝑠 = 83.8 𝑚𝑚𝑚𝑚/𝑠𝑠
∆
𝑙𝑙2
𝑣𝑣
𝑟𝑟𝑑𝑑𝑑𝑑𝑑𝑑𝑑𝑑 = 0.1 𝑚𝑚
𝜔𝜔 = 40 ∗
2𝜋𝜋
= 4.19 𝑟𝑟𝑟𝑟𝑟𝑟/𝑠𝑠
60
4
3/23 If the coefficients of static and kinetic friction between the 20-kg block A and the
100-kg cart B are both essentially the same value of 0.50, determine the acceleration of
each part for (a) P = 60 N and (b) P = 40 N.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 6th ed., SI version, John Wiley & Sons, Inc., 2008. Problem 3/23 ]
P = 60 N
𝑚𝑚𝑚𝑚
𝑁𝑁
𝑓𝑓
𝑁𝑁1
𝑓𝑓
𝑁𝑁
2𝑃𝑃
𝐴𝐴: Σ𝐹𝐹𝑥𝑥 = 𝑚𝑚𝑎𝑎𝑥𝑥
120 − 𝜇𝜇𝜇𝜇 = 𝑚𝑚𝐴𝐴 𝑎𝑎𝐴𝐴
𝑎𝑎𝐴𝐴 =
120 − 0.5(20)(9.81)
= 1.095 𝑚𝑚/𝑠𝑠 2
20
𝐵𝐵: Σ𝐹𝐹𝑥𝑥 = 𝑚𝑚𝑎𝑎𝑥𝑥
𝑁𝑁2
𝜇𝜇𝜇𝜇 = 𝑚𝑚𝐵𝐵 𝑎𝑎𝐵𝐵
𝑎𝑎𝐵𝐵 =
0.5(20)(9.81)
= 0.981 𝑚𝑚/𝑠𝑠 2
100
3/23 If the coefficients of static and kinetic friction between the 20-kg block A and the
100-kg cart B are both essentially the same value of 0.50, determine the acceleration of
each part for (a) P = 60 N and (b) P = 40 N.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 6th ed., SI version, John Wiley & Sons, Inc., 2008. Problem 3/23 ]
P = 40 N
𝑚𝑚𝑚𝑚
𝑁𝑁
𝑁𝑁1
𝑚𝑚𝑚𝑚
𝑁𝑁2
𝑓𝑓
2𝑃𝑃
2𝑃𝑃
𝐴𝐴: Σ𝐹𝐹𝑥𝑥 = 𝑚𝑚𝑎𝑎𝑥𝑥
80 − 𝜇𝜇𝜇𝜇 = 𝑚𝑚𝐴𝐴 𝑎𝑎𝐴𝐴
𝑎𝑎𝐴𝐴 =
80 − 0.5(20)(9.81)
= −0.905 𝑚𝑚/𝑠𝑠 2
20
𝐴𝐴 + 𝐵𝐵: Σ𝐹𝐹𝑥𝑥 = 𝑚𝑚𝑎𝑎𝑥𝑥
2𝑃𝑃 = 𝑚𝑚𝑚𝑚
𝑎𝑎 =
2(40)
= 0.667 𝑚𝑚/𝑠𝑠 2
120
Not possible
3/83. The car has a speed of 70 km/h at the bottom of the dip when the driver applies
the breaks, causing a deceleration of 0.5g. What is the minimum seat cushion angle 𝜃𝜃 for
which a package will not slide forwards? The coefficient of static friction between the
package and the seat cushion is (a) 0.2 and (b) 0.4.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 6th ed., SI version, John Wiley & Sons, Inc., 2008. Problem 3/83 ]
𝑛𝑛
𝑚𝑚𝑚𝑚
𝑁𝑁
𝑓𝑓
𝑡𝑡
Σ𝐹𝐹𝑡𝑡 = 𝑚𝑚𝑎𝑎𝑡𝑡
𝑣𝑣 = 70 ∗
−𝜇𝜇𝑆𝑆 𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁 − 𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁 = 𝑚𝑚(−0.5𝑔𝑔)
0.5𝑚𝑚𝑚𝑚
𝑁𝑁 =
𝜇𝜇𝑆𝑆 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 + 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠
1,000
= 19.44 𝑚𝑚/𝑠𝑠
3,600
Σ𝐹𝐹𝑛𝑛 = 𝑚𝑚𝑎𝑎𝑛𝑛
𝑣𝑣 2
𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁 − 𝜇𝜇𝑆𝑆 𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁𝑁 − 𝑚𝑚𝑚𝑚 = 𝑚𝑚
𝜌𝜌
0.5𝑚𝑚𝑚𝑚
𝜇𝜇𝑆𝑆 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 + 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠
𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 − 𝜇𝜇𝑆𝑆 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠 − 𝑚𝑚𝑚𝑚 = 4.724𝑚𝑚
3/83. The car has a speed of 70 km/h at the bottom of the dip when the driver applies
the breaks, causing a deceleration of 0.5g. What is the minimum seat cushion angle 𝜃𝜃 for
which a package will not slide forwards? The coefficient of static friction between the
package and the seat cushion is (a) 0.2 and (b) 0.4.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 6th ed., SI version, John Wiley & Sons, Inc., 2008. Problem 3/83 ]
0.5𝑚𝑚𝑚𝑚
𝜇𝜇𝑆𝑆 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 + 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠
𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 − 𝜇𝜇𝑆𝑆 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠 − 𝑚𝑚𝑚𝑚 = 4.724𝑚𝑚
4.724 + 9.81
𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 − 𝜇𝜇𝑆𝑆 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠 =
𝜇𝜇𝑆𝑆 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 + 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠
0.5 9.81
= 2.963𝜇𝜇𝑆𝑆 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 + 2.963𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠
1 − 2.963𝜇𝜇𝑠𝑠 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐 = (𝜇𝜇𝑠𝑠 + 2.963)𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠
1 − 2.963𝜇𝜇𝑠𝑠
𝑡𝑡𝑡𝑡𝑡𝑡𝜃𝜃 =
𝜇𝜇𝑠𝑠 + 2.963
𝑎𝑎) 𝜇𝜇𝑠𝑠 = 0.2
𝑏𝑏) 𝜇𝜇𝑠𝑠 = 0.4
→
→
𝜃𝜃 = 7.34°
𝜃𝜃 = −3.15°
3/163 If the system is released from rest, determine the speeds of both masses after B has
moved 1 m. Neglect friction and the masses of the pulleys.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 6th ed., SI version, John Wiley & Sons, Inc., 2008. Problem 3/163 ]
Direction of motion ?
𝑚𝑚𝐴𝐴 𝑔𝑔
𝑁𝑁2
3𝑇𝑇
𝑁𝑁1
2𝑇𝑇
𝑚𝑚𝑚𝑚
Assume equilibrium
3𝑇𝑇 − 𝑚𝑚𝐴𝐴 𝑔𝑔𝑔𝑔𝑔𝑔𝑔𝑔𝑔𝑔 = 0
40 9.81 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠
= 44.74 𝑁𝑁
𝑇𝑇 =
3
𝑚𝑚𝑚𝑚 − 2𝑇𝑇 = 0
𝑚𝑚 =
2(44.74)
= 9.12 𝑘𝑘𝑘𝑘
9.81
𝑚𝑚𝐵𝐵 = 8 < 9.12
Not equilibrium
B moves up & A moves down
3/163 If the system is released from rest, determine the speeds of both masses after B has
moved 1 m. Neglect friction and the masses of the pulleys.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 6th ed., SI version, John Wiley & Sons, Inc., 2008. Problem 3/163 ]
′
𝑇𝑇1 + 𝑉𝑉𝑔𝑔𝑔 + 𝑈𝑈1−2
= 𝑇𝑇2 + 𝑉𝑉𝑔𝑔𝑔
′
𝑇𝑇1 = 0, 𝑉𝑉𝑔𝑔𝑔 = 0, 𝑈𝑈1−2
=0
1
1
2
𝑇𝑇2 = 𝑚𝑚𝐴𝐴 𝑣𝑣𝐴𝐴 + 𝑚𝑚𝐵𝐵 𝑣𝑣𝐵𝐵2 = 20𝑣𝑣𝐴𝐴2 + 4𝑣𝑣𝐵𝐵2
2
2
𝑉𝑉𝑔𝑔𝑔 = −𝑚𝑚𝐴𝐴 𝑔𝑔∆ℎ𝐴𝐴 + 𝑚𝑚𝐵𝐵 𝑔𝑔∆ℎ𝐵𝐵 = −392.4∆ℎ𝐴𝐴 + 78.48(1)
0 = 20𝑣𝑣𝐴𝐴2 + 4𝑣𝑣𝐵𝐵2 − 392.4∆ℎ𝐴𝐴 + 78.48
3/163 If the system is released from rest, determine the speeds of both masses after B has
moved 1 m. Neglect friction and the masses of the pulleys.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 6th ed., SI version, John Wiley & Sons, Inc., 2008. Problem 3/163 ]
0 = 20𝑣𝑣𝐴𝐴2 + 4𝑣𝑣𝐵𝐵2 − 392.4∆ℎ𝐴𝐴 + 78.48
Constrained motion
𝐿𝐿 = 3𝑙𝑙𝐴𝐴 + 2𝑙𝑙𝐵𝐵 + 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐
0 = 3𝑙𝑙𝐴𝐴̇ + 2𝑙𝑙𝐵𝐵̇
(1)
𝑙𝑙𝐴𝐴
𝐿𝐿 = 3 𝑙𝑙𝐴𝐴 + ∆𝑙𝑙𝐴𝐴 + 2 𝑙𝑙𝐵𝐵 + ∆𝑙𝑙𝐵𝐵 + 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐
2 − 1 ∶
∆𝑙𝑙𝐵𝐵 = −1 ∶
0 = 20
0 = 3∆𝑙𝑙𝐴𝐴 + 2∆𝑙𝑙𝐵𝐵
2
∆𝑙𝑙𝐴𝐴 =
3
𝑚𝑚
∆𝑙𝑙𝐴𝐴
𝑙𝑙𝐵𝐵
(2)
∆ℎ𝐴𝐴
2
2
− 𝑣𝑣𝐵𝐵 + 4𝑣𝑣𝐵𝐵2 − 392.4(0.228) + 78.48
3
∆ℎ𝐴𝐴 = ∆𝑙𝑙𝐴𝐴 𝑠𝑠𝑠𝑠𝑠𝑠𝑠𝑠 = 0.228 𝑚𝑚
→ 𝑣𝑣𝐵𝐵 = −0.923 𝑚𝑚/𝑠𝑠 (up)
2
3
𝑣𝑣𝐴𝐴 = − 𝑣𝑣𝐵𝐵 = 0.615 𝑚𝑚/𝑠𝑠 (down)
3/148 The 1.5-kg slider C moves along the fixed rod under the action of the spring whose
unstretched length is 0.3 m. If the velocity of the slider is 2 m/s at point A and 3 m/s at point
B, calculate the work Uƒ done by friction between these two points. Also, determine the
average friction force acting on the slider between A and B if the length of the path is 0.70 m.
The x-y plane is horizontal.
[ Meriam, J.L. and Kraige, L.G., Engineering Mechanics: Dynamics, 7th ed., John Wiley & Sons, Inc., 2012. Problem 3/148 ]
′
𝑇𝑇1 + 𝑉𝑉𝑒𝑒𝑒 + 𝑉𝑉𝑔𝑔𝑔 + 𝑈𝑈1−2
= 𝑇𝑇2 + 𝑉𝑉𝑒𝑒𝑒 +𝑉𝑉𝑔𝑔𝑔
′
𝑈𝑈1−2
= ∆𝑇𝑇 + ∆𝑉𝑉𝑒𝑒 + ∆𝑉𝑉𝑔𝑔
1
1
2
2
∆𝑇𝑇 = 𝑚𝑚 𝑣𝑣2 − 𝑣𝑣1 = 1.5 32 − 22 = 3.75 𝐽𝐽
2
2
1
1
∆𝑉𝑉𝑒𝑒 = 𝑘𝑘 𝑥𝑥22 − 𝑥𝑥12 = 800 0.12 − 0.22 = −12 𝐽𝐽
2
2
∆𝑉𝑉𝑔𝑔 = 𝑚𝑚𝑚𝑚 ℎ2 − ℎ1 = 1.5(9.81)(0.4 − 0) = 5.886 𝐽𝐽
′
𝑈𝑈1−2
= 3.75 − 12 + 5.886 = −2.364 𝐽𝐽
′
𝑈𝑈1−2
= −𝑓𝑓 ∗ 𝑠𝑠
→ 𝑓𝑓 =
2.364
= 3.377 𝑁𝑁
0.7