NORYL™ Resin NHP6011
Polyphenylene Ether
SABIC
www.ulprospector.com
Technical Data
Product Description
NORYL NHP6011 resin is an 8% glass fiber reinforced blend of polyphenylene ether (PPE). This injection moldable grade contains nonbrominated, non-chlorinated flame retardant and carries a CTI 2 and UL94 flame rating of V0 at 1.5mm for thin-wall molding capability. NORYL
NHP6011 is based on a unique co-polymer technology and exhibits high impact, high heat resistance, dimensional stability, hydrolytic stability,
strong electrical performance, low moisture absorption and very low specific gravity. This material is an excellent candidate for electrical vehicle
(EV) battery modules/housings.
General
Material Status
• Commercial: Active
Literature 1
UL Yellow Card 2
Search for UL Yellow Card
Availability
Filler / Reinforcement
Features
Uses
Processing Method
• Brochure - NORYL™ Next Gen Battery Module Solutions (Chinese)
• Drones
• NORYL Resin - Chemical Resistance Properties
• NORYL RESIN SOLUTIONS FOR ELECTRIC VEHICLE BATTERY MODULES
• SABIC NORYL Resin Injection Molding Processing Guide
• SABIC-MOBILITY-ADAS CAMERA FLYER
• SABIC-MOBILITY-ADAS LIDAR FLYER
• E207780-104507609
• SABIC
• NORYL™ Resin
• Africa & Middle East
• Europe
• North America
• Asia Pacific
• Latin America
• Glass Fiber, 8.0% Filler by Weight
• Amorphous
• Good Stiffness
• Hydrolytically Stable
• Bromine Free
• Halogen Free
• Low Moisture Absorption
• Chlorine Free
• High Heat Resistance
• Low Shrinkage
• Flame Retardant
• High Stiffness
• Low Specific Gravity
• Good Dimensional Stability
• High Strength
• Low Warpage
Electrical/Electronic
•
• Electric Vehicle Applications
Applications
• Electrical Parts
• Energy Storage
• Injection Molding
Physical
Density / Specific Gravity
Melt Volume-Flow Rate (MVR) (280°C/10.0 kg)
Molding Shrinkage
Flow
Across Flow
Water Absorption
Nominal Value Unit
1.16 g/cm³
15 cm³/10min
Test Method
ASTM D792
ISO 1183
ISO 1133
Internal Method
0.50 to 0.70 %
0.50 to 0.70 %
0.020 %
0.050 %
Nominal Value Unit
ASTM D570
ISO 62
ASTM D570
ISO 62
ISO 62
ISO 62
Test Method
-- 5
-Tensile Strength
3300 MPa
3300 MPa
ASTM D638
ISO 527-1/1
Break 6
Break
Tensile Elongation
75.0 MPa
75.0 MPa
ASTM D638
ISO 527-2/5
3.0 %
3.0 %
ASTM D638
ISO 527-2/5
24 hr, 23°C
0.10 %
Saturation, 23°C
0.20 %
Equilibrium, 23°C, 50% RH 4
Equilibrium, 23°C, 50% RH
Mechanical
Tensile Modulus
Break 6
Break
1 of 6
Form No. TDS-350291-en
UL LLC ©2022. All rights reserved.
UL Prospector | 800-788-4668 or 307-742-9227 | www.ulprospector.com.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL
assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product
or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The
content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.
Document Created: Tuesday, September 20, 2022
Added to Prospector: May 2021
Last Updated: 6/21/2022
NORYL™ Resin NHP6011
Polyphenylene Ether
SABIC
www.ulprospector.com
Mechanical
Flexural Modulus
Nominal Value Unit
Test Method
50.0 mm Span 7
3000 MPa
ASTM D790
-- 8
3000 MPa
ISO 178
115 MPa
ASTM D790
115 MPa
Nominal Value Unit
ISO 178
Test Method
ISO 179/1eA
Flexural Strength
50.0 mm Span 7
-- 8
Impact
Charpy Notched Impact Strength 9
-30°C
23°C
Charpy Unnotched Impact Strength 9
-30°C
23°C
Notched Izod Impact
-30°C
23°C
-30°C 10
23°C 10
Unnotched Izod Impact
-30°C
23°C
-30°C 10
23°C 10
Instrumented Dart Impact
23°C, Energy at Peak
23°C, Total Energy
Multi-Axial Instrumented Impact Peak Force
23°C
Hardness
Rockwell Hardness (M-Scale)
Ball Indentation Hardness (H 358/30)
Thermal
Deflection Temperature Under Load
0.45 MPa, Unannealed, 3.20 mm
6.0 kJ/m²
10 kJ/m²
ISO 179/1eU
35 kJ/m²
35 kJ/m²
75 J/m
100 J/m
6.0 kJ/m²
ASTM D256
ASTM D256
ISO 180/1A
10 kJ/m²
ISO 180/1A
450 J/m
450 J/m
35 kJ/m²
ASTM D4812
ASTM D4812
ISO 180/1U
35 kJ/m²
ISO 180/1U
ASTM D3763
4.00 J
9.00 J
ASTM D3763
1140 N
Nominal Value Unit
71
161 MPa
Nominal Value Unit
Test Method
ASTM D785
ISO 2039-2
ISO 2039-1
Test Method
140 °C
140 °C
130 °C
130 °C
ASTM D648
ISO 75-2/Bf
ASTM D648
ISO 75-2/Af
--
151 °C
ASTM D1525 11
ISO 306/A50 11
--
139 °C
ASTM D1525 12
ISO 306/B50 12
--
141 °C
0.45 MPa, Unannealed, 4.00 mm, 64.0 mm Span 10
1.8 MPa, Unannealed, 3.20 mm
1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span 10
Vicat Softening Temperature
Ball Pressure Test (123 to 127°C)
CLTE
Flow : -40 to 40°C
Transverse : -40 to 40°C
Pass
3.4E-5 cm/cm/°C
5.5E-5 cm/cm/°C
Thermal Conductivity
0.21 W/m/K
RTI Elec
65.0 °C
2 of 6
ASTM D1525 13
ISO 306/B120 13
IEC 60695-10-2
ASTM E831
ISO 11359-2
ASTM D5930
ISO 8302
UL 746B
Form No. TDS-350291-en
UL LLC ©2022. All rights reserved.
UL Prospector | 800-788-4668 or 307-742-9227 | www.ulprospector.com.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL
assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product
or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The
content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.
Document Created: Tuesday, September 20, 2022
Added to Prospector: May 2021
Last Updated: 6/21/2022
NORYL™ Resin NHP6011
Polyphenylene Ether
SABIC
www.ulprospector.com
Thermal
RTI Imp
RTI Str
Electrical
Nominal Value Unit
65.0 °C
65.0 °C
Nominal Value Unit
Surface Resistivity
2.9E+16 ohms
Volume Resistivity
1.6E+16 ohms·cm
Electric Strength
0.800 mm, in Oil
1.60 mm, in Air
3.20 mm, in Oil
Dielectric Constant
51 kV/mm
28 kV/mm
22 kV/mm
60 Hz
2.73
50 kHz
2.73
1 MHz
3.19
50 Hz
Dissipation Factor
50 Hz
60 Hz
1 MHz
2.73
Arc Resistance 14
Comparative Tracking Index (CTI)
Comparative Tracking Index
High Amp Arc Ignition (HAI) (> 1.5 mm)
High Voltage Arc Resistance to Ignition (HVAR)
Hot-wire Ignition (HWI) (> 1.5 mm)
Flammability
Flame Rating (> 1.5 mm)
Glow Wire Flammability Index
1.5 mm
3.0 mm
Glow Wire Ignition Temperature
1.5 mm
3.0 mm
Injection
Drying Temperature
Drying Time
Suggested Max Moisture
Suggested Shot Size
Rear Temperature
Middle Temperature
Front Temperature
Nozzle Temperature
Processing (Melt) Temp
Mold Temperature
Back Pressure
Screw Speed
Injection Notes
• Drying Time (Cumulative): 8 hr
Test Method
UL 746B
UL 746B
Test Method
ASTM D257
IEC 60093
ASTM D257
IEC 60093
IEC 60243-1
•
•
0.20
0.20
3.7E-3
PLC 7
PLC 2
275 V
PLC 0
PLC 3
PLC 0
Nominal Value Unit
V-0
5VB
ASTM D150
IEC 60250
ASTM D150
ASTM D150
IEC 60250
IEC 60250
ASTM D150
IEC 60250
ASTM D495
UL 746A
IEC 60112
UL 746A
UL 746A
UL 746A
Test Method
UL 94
IEC 60695-2-12
800 °C
825 °C
IEC 60695-2-13
960 °C
960 °C
Nominal Value Unit
105 to 110 °C
3.0 to 4.0 hr
0.020 %
30 to 70 %
250 to 300 °C
260 to 305 °C
270 to 310 °C
280 to 310 °C
280 to 310 °C
75 to 105 °C
0.300 to 0.700 MPa
20 to 100 rpm
3 of 6
Form No. TDS-350291-en
UL LLC ©2022. All rights reserved.
UL Prospector | 800-788-4668 or 307-742-9227 | www.ulprospector.com.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL
assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product
or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The
content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.
Document Created: Tuesday, September 20, 2022
Added to Prospector: May 2021
Last Updated: 6/21/2022
NORYL™ Resin NHP6011
Polyphenylene Ether
SABIC
www.ulprospector.com
Notes
1 These links provide you with access to supplier literature. We work hard to keep them up to date; however you may find the most current literature
from the supplier.
2 A UL Yellow Card contains UL-verified flammability and electrical characteristics. UL Prospector continually works to link Yellow Cards to
individual plastic materials in Prospector, however this list may not include all of the appropriate links. It is important that you verify the association
between these Yellow Cards and the plastic material found in Prospector. For a complete listing of Yellow Cards, visit the UL Yellow Card Search.
3 Typical properties: these are not to be construed as specifications.
4 24 hrs
5 5.0 mm/min
6 Type I, 5.0 mm/min
7 1.3 mm/min
8 2.0 mm/min
9 80*10*4 sp=62mm
10 80*10*4 mm
11 Rate A (50°C/h), Loading 1 (10 N)
12 Rate A (50°C/h), Loading 2 (50 N)
13 Rate B (120°C/h), Loading 2 (50 N)
14 Tungsten Electrode
4 of 6
Form No. TDS-350291-en
UL LLC ©2022. All rights reserved.
UL Prospector | 800-788-4668 or 307-742-9227 | www.ulprospector.com.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL
assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product
or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The
content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.
Document Created: Tuesday, September 20, 2022
Added to Prospector: May 2021
Last Updated: 6/21/2022