2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
Register
LOGIN
EMAIL US
THE IMPORTANCE OF PCB TRACE
WIDTHS IN PCB DESIGN
The Importance of PCB Trace Widths in PCB Design
There are several factors that drive trace width, length, and style during the PCB design process of your next PCB prototype. This article will
dive into a variety of applications that demand specific trace layout characteristics and how or when to incorporate them into your PCB design.
What is Trace Width?
Let’s start with the basics. What exactly is trace width and why is specifying a particular trace width so important? The point of a PCB trace is to
connect any kind of electrical signal, whether it be analog, digital, or power, from one junction to another.
The junction can be the pin of a component, a branch off of a larger trace or plane, or an empty pad or test-point intended for probing. Trace
widths are often measured in mils, or thousands of an inch. A standard trace width for an ordinary signal (no special requirements) may be in
the 7-12 mil range and be as long as a few inches, but there are many things that should be considered when defining the width and length of a
trace.
The application will often drive the trace widths and types in a PCB design and at a certain point, there is usually a balance with regards to PCB
fabrication cost, board density/size, and performance. If a board has specific design requirements such as speed optimization, noise or
coupling mitigation, or high current/voltage, the trace widths and types might be more important than optimizing for manufacturing cost of the
bare PCB or overall board size.
Get your PCBs Built-Fast.
CONTACT US FOR A PCB QUOTE
or call us at 1-800-SFC-5143
Trace-Related Specifications in PCB Fabrication
As a general rule, the following trace-related specifications begin to drive up bare PCB fabrication costs.
The costs become considerably higher due to tighter PCB tolerances and higher end equipment needed to both manufacture and inspect or
test the PCBs:
Trace widths narrower than 5 mils (0.005”)
Trace spacing closer than 5 mils
Via holes with a diameter smaller than 8 mils
Trace thickness thinner or thicker than 1 ounce (which equates to 1.4 mils)
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
1/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
Differential pairs and controlled lengths or trace impedance
High density designs incorporating PCB footprints such as very fine pitch BGAs or high signal count parallel buses might require trace widths
as thin as 2.5 mils and special kinds of vias such as laser-drilled micro-vias containing diameters of 6 mils or less. In contrast, some high-power
designs might require very large traces or planes consuming an entire layer and at thicker ounce pours than standard. Space constrained
applications might require very thin boards containing several layers and a limited copper pour thickness of half an ounce (0.7 mil thickness).
In some other cases, a design with high speed communication from one peripheral to another might require traces with controlled impedance
and specific width and spacing from each other to minimize reflections and inductive coupling. Or the design might need to be a certain length
to match other associated signals in a bus. High voltage applications require certain safety features such as minimized distance between two
exposed differential signals to prevent arcing. Whatever the feature or characteristic, trace definition matters so let’s explore a variety of
applications.
Exclusive: Get our FREE Intro to Flex
Circuits E-Book
Subscribe to our email list below and we'll send you
our e-book
Introduction to Flex PCBs.
Enter Email Address
Sign Up
By submitting, you agree to receive emails from San
Francisco Circuits. We will never sell or distribute your
information to 3rd parties. You will be able to unsubscribe
any time.
Various Trace Widths and Thicknesses
It’s common for a PCB to contain a variety of trace widths as they are dependent on the needs of the signal (as shown in Figure 1). The thinner
traces shown are for general purpose TTL (Transistor-Transistor Logic) level signals with no special requirements for high current or noise
protection.
These would be the most common types of traces on a circuit board.
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
2/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
Figure 1. Example of a 4-layer board containing varying trace widths and types
The thicker traces have been optimized for current carrying capacity and are used for peripherals or power-related functions that demand
higher power, such as fans, motors, and general power delivery to lower level components. And there’s even a differential signal (USB high
speed) shown in the top-left section of the figure with specific spacing and width defined to meet 90-Ohm impedance requirements. Figure 2
shows a slightly denser board with 6 layers and a BGA (ball grid array) component requiring thinner traces.
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
3/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
Example of a 6-layer board containing a 256-pin BGA component with 5-mil trace widths
How is PCB Trace Width Calculated?
Let's walk through the process of calculating for a certain trace width for a power signal delivering current from one power component to a
peripheral. In this example, we’ll be calculating the minimum trace width for a power-path used for a DC motor. The power-path starts at a fuse,
travels through an H-bridge (a component used to manage power delivery across a DC’s motor windings), and ends at the motor’s connector.
The average continuous max current demanded by the DC motor will be around 2 Amps.
Now, a PCB trace acts as a resistor and the longer and narrower the trace, the more resistance is added. If the trace isn’t properly defined, the
high current could damage the trace and/or introduce significant voltage drop to the motor (resulting in a slower speed). NetC21_2 shown in
Figure 3 is about 0.8” long and needs to carry 2 Amps max. If we assume some general things like a 1-ounce copper pour and ambient roomtemperature during normal operation, we have what we need to calculate both the minimum trace width and expected voltage drop at that
width.
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
4/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
Example of optimized trace width for DC motor's power-path
How do you Calculate PCB Trace Resistance?
The following is an equation used for trace area:
Area[mils²] = ( Current[Amps] / (k*( Temp_Rise[°C] )^b) )^(1/c) where following IPC guidelines for an external (or top/bottom) layer, k =
0.048, b = 0.44, c = 0.725. Note that the only variable we really need to plug in here is current.
And using this area in the following equation will give us the necessary width which tells us how wide our trace needs to be to carry the current
without any potential issues:
Width[mils] = Area[mils^2]/(Thickness[oz]*1.378[mils/oz]) where 1.378 is associated with the standard 1 ounce pour thickness.
By plugging in 2 amps into the above calculation we get around 30 mils minimum for the trace.
But what this doesn’t tell us is what the voltage drop will be. This is a bit more involved as it requires a calculation of the trace’s resistance
which can be calculated per the equation shown in Figure 4.
Figure 4. Formula for PCB trace resistance
In this formula, ρ = resistivity of copper, α = temperature coefficient of copper, T = trace thickness, W = trace width, L = trace length, and t =
temperature. If all the associated values are plugged in for a 0.8inch long trace at 30mils width, we find that the trace resistance will be around
0.03? and will drop the voltage about 26mV which would be more than OK for the application. It’s helpful to know what impacts these values.
PCB Trace Spacing & Length
For digital designs with high speed communication, specific spacing and tuned lengths may be required to minimize cross-talk, coupling, and
reflections. Some common applications for this are USB-based serial differential signals, and RAM-based parallel differential signals. Generally,
USB 2.0 will require differential pair routing at speeds of 480Mbit/s (USB high speed class) or higher. This is partly because high-speed USB
generally operates at a much lower voltage and differential, bringing the overall signal level closer to the noise floor.
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
5/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
There are three important things to consider when routing high speed USB lines: trace width, trace spacing, and trace length.
All are important but the most critical out of the three is making sure the two traces are matched as closely as possible in length. As a general
rule of thumb, if the traces differ any more than 50 mils in length from each other (for high speed USB), it significantly increases risk of
reflections which could result in poor communication. 90 Ohm matched impedance is a common specification for differential pair routing and to
achieve this, the traces should be optimized in width and spacing.
Figure 5 shows an example of a differential pair routed for a high-speed USB interface, containing 12-mil wide traces at 15-mil spacing.
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
6/14
2/1/25, 9:20 PM
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
The Importance of PCB Trace Widths in PCB Design
7/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
Figure 5. Differential routing for USB2.0 high speed
An interface for a memory-based component containing a parallel interface, such as DDR3-SDRAM, will be much more tightly constrained in
terms of trace length. Most higher-end PCB design software will have length-tuning features that will optimize trace length to match all
associated signals in a parallel bus. Figure 6 shows an example of a DDR3 layout with length-tuned traces.
Figure 6. Example of length-tuned DDR3 memory traces
Ground-Filled Traces and Planes
Some applications with noise-sensitive components such as wireless chips or antennas may require a little extra protection. Designing traces
and planes with embedded ground vias can greatly help minimize coupling picked up by nearby traces or planes and also off-board signals that
creep into the board edge.
Figure 7 shows an example of a Bluetooth module placed near the edge of a board with its antenna (labelled via silkscreen “ANT”) on the
outside of a thick trace containing embedded vias connected to a ground plane. This helps isolate the antenna from the other on-board circuitry
and planes.
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
8/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
Figure 7. Bluetooth module with a ground-via embedded trace to help with noise suppression
Another method of this ground-via embedded trace (or polygon plane in this instance) could be used to protect the boards circuitry from
outside, off-board wireless signals. Figure 8 shows a noise-sensitive PCB with a ground-via embedded plane along the perimeter of the board.
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
9/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
Figure 8. Ground plane with vias lining a sensitive PCB to protect against off-board interference
Best-Practices for PCB Routing
Many things drive trace characteristics in the PCB world so make sure to follow best practices when routing your next PCB and you’ll find that
balance between PCB fab cost, circuit density, and overall performance.
If you’re looking for a quote for your next PCB application, connect with our team of experts to help you get exactly what you need at the right
price. We specialize in PCB fabrication and PCB assembly conforming to intricate designs typical boardhouses can't manufacture or assemble.
Let us help you bring your design into reality.
Get your PCBs Built-Fast.
CONTACT US FOR A PCB QUOTE
or call us at 1-800-SFC-5143
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
10/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
PCB School
NIST 800-171 Compliance for PCB Manufacturers: Protect Your Data & Contracts
Discover why NIST 800-171 compliance is essential for PCB manufacturers. As a PCB buyer, learn how this cybersecurity framework
safeguards your sensitive data & ensure you are engaged with a boardhouse that meets these requirements.
Read More
PCB School
High-Speed Circuit Design for Modern Circuitry
San Francisco Circuits covers board-level tips for the design & layout of high-speed circuits in advanced applications.
Read More
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
11/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
PCB School
PCB Line Spacing: A Comprehensive Breakdown for High Voltage Applications
PCB line tracing relates to both function and safety in circuitry. We discuss the significance of careful line tracing through both
clearance and creepage.
Read More
PCB School
Via Tenting Principles in PCB Layouts
Via tenting is the application of soldermask to encase or seal the via’s opening. A via is essentially a hole drilled into the PCB that
facilitates connections between multiple PCB layers. An untented via, on the other hand, remains uncovered by a soldermask layer.
The decision to expose or cover these vias carries both advantages and disadvantages contingent upon your specific design and
manufacturing requirements.
Read More
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
12/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
PCB School
PCB Assembly Drawings: Polarities, Pin1 & Anode/Cathode Markings
The Essential Guide to PCB Assembly Drawings: Understanding Polarities, Pin1 Marking & Anode/Cathode Markings. Learn more
about understanding the XY File, component locations, & polarized component orientations.
Read More
PCB School
PCB Insertion Loss
This article explores insertion loss: its properties, how loss occurs throughout a signal path in a system, and things we can do to
minimize it.
Read More
About Us
Contact Us
Terms & Privacy
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
Site Map
13/14
2/1/25, 9:20 PM
The Importance of PCB Trace Widths in PCB Design
San Francisco Circuits, Inc.
San Francisco Circuits - San Diego
1660 S Amphlett Blvd #200
San Mateo,CA 94402
3914 Murphy Canyon Rd., Suite A244
San Diego, CA 92123
Toll-Free: (800)732-5143
E-mail: sales@sfcircuits.com
Local: (858)576-7202
Follow us
©Copyright 2005 - 2025 - San Francisco Circuits, Inc. - All rights reserved
Latest News
09-09-2024
San Francisco Circuits covers board-level tips for the design & layout of high-speed circuits in advanced applications.
Read more
06-10-2024
PCB Line Spacing: A Comprehensive Breakdown for High Voltage Applications. As PCBs become more complicated, more precise
measurements and spacing are required. This article explains PCB line spacing, tracing, clearance, and creepage.
Read more
User Login
Email
Password
Remember me
Login
Get a quote
Forgot Password
https://www.sfcircuits.com/pcb-school/pcb-trace-widths
14/14