Inductive Sensor
with Analog Output
IW045CM65MG3
Part Number
Technical Data
Inductive Data
Working Range
1,5...4,5 mm
Measuring Range
3 mm
Measuring Distance
Correction Factors Stainless Steel V2A/CuZn/Al
Mounting
Mounting A/B/C/D in mm
Standard Target FE360, thickness 1 mm
Linearity
Resolution
Electrical Data
3 mm
1,2/1,2/1,2
flush
0/18/13,5/0
18 × 18 mm
<1%
1 µm
Supply Voltage
18...30 V DC
Cut-Off Frequency
900 Hz
Current Consumption (Ub = 24 V)
Temperature Drift (-10 °C < Tu ≤ 50 °C)
Temperature Drift (50 °C < Tu ≤ 70 °C)
Temperature Range
Analog Output
Load Current Voltage Output
Resistant to Magnetic Fields
Short Circuit Protection
Reverse Polarity Protection
Protection Class
Mechanical Data
< 30 mA
5 µm/K
6 µm/K
-10...70 °C
0...10 V
< 1 mA
yes
yes
yes
III
Housing Material
CuZn, nickel-plated
Degree of Protection
IP67
Full Encapsulation
Connection
yes
M12 × 1; 4-pin
Analog Output
Connection Diagram No.
Suitable Connection Equipment No.
Suitable Mounting Technology No.
Complementary Products
Analog Evaluation Unit AW02
Inductive Sensors
2
1 = Analog Output Indicator
All dimensions in mm (1 mm = 0.03937 Inch)
Legend
PoE
ower over Ethernet
IN
Safety Input
OSSD
Safety Output
Signal
Signal Output
BI_D+/– Ethernet Gigabit bidirect. data line (A-D)
EN0 RS422 Encoder 0-pulse 0/ (TTL)
PT
Platinum measuring resistor
nc
U
W
W–
O
O–
BZ
A MV
a
b
SY
SY–
E+
S+
SnR
Rx+/–
Tx+/–
B US
La
Mag
RES
EDM
ENARS422
Not connected
Test Input
Test Input inverted
Trigger Input
Ground for the Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Ground for the Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Encoder A/Ā (TTL)
Mounting
IND. CONT. EQ
72HL / E189727
For use in class 2 circuits
ENBRS422 Encoder B/ (TTL)
ENA
Encoder A
ENB
Encoder B
AMIN
Digital output MIN
AMAX
Digital output MAX
AOK
Digital output OK
SY In
Synchronization In
SY OUT Synchronization OUT
OLT
Brightness output
M
Maintenance
rsv
Reserved
Wire Colors according to DIN IEC 60757
BK
Black
BN
Brown
RD
Red
OG
Orange
YE
Yellow
GN
Green
BU
Blue
VT
Violet
GY
Grey
WH
White
PK
Pink
GNYE
Green/Yellow
V0-31.03.2023
E
T
Z
S
RxD
TxD
RDY
GND
CL
E/A
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Specifications are subject to change without notice
+
–
~
A
Ā
V
