WCDMA Radio Network Configuration
Parameters
DN00211177
Issue 12B
Approval Date 2013-06-13
Nokia Siemens Networks is continually striving to reduce the adverse environmental effects of
its products and services. We would like to encourage you as our customers and users to join
us in working towards a cleaner, safer environment. Please recycle product packaging and
follow the recommendations for power use and proper disposal of our products and their components.
If you should have questions regarding our Environmental Policy or any of the environmental
services we offer, please contact us at Nokia Siemens Networks for any additional information.
WCDMA Radio Network Configuration Parameters
The information in this document is subject to change without notice and describes only the
product defined in the introduction of this documentation. This documentation is intended for the
use of Nokia Siemens Networks customers only for the purposes of the agreement under which
the document is submitted, and no part of it may be used, reproduced, modified or transmitted
in any form or means without the prior written permission of Nokia Siemens Networks. The
documentation has been prepared to be used by professional and properly trained personnel,
and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes
customer comments as part of the process of continuous development and improvement of the
documentation.
The information or statements given in this documentation concerning the suitability, capacity,
or performance of the mentioned hardware or software products are given "as is" and all liability
arising in connection with such hardware or software products shall be defined conclusively and
finally in a separate agreement between Nokia Siemens Networks and the customer. However,
Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions
contained in the document are adequate and free of material errors and omissions. Nokia
Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which
may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO
EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED
TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY
OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION
IN IT.
This documentation and the product it describes are considered protected by copyrights and
other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark
of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective
owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2013. All rights reserved
f Important Notice on Product Safety
This product may present safety risks due to laser, electricity, heat, and other sources
of danger.
Only trained and qualified personnel may install, operate, maintain or otherwise handle
this product and only after having carefully read the safety information applicable to this
product.
The safety information is provided in the Safety Information section in the “Legal, Safety
and Environmental Information” part of this document or documentation set.
The same text in German:
f Wichtiger Hinweis zur Produktsicherheit
Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder
andere Gefahrenquellen ausgehen.
Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch
geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheitsanforderungen erfolgen.
Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal,
Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentationssatzes.
2
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table of Contents
This document has 3727 pages.
1
1.1
1.1.1
1.1.1.1
1.1.2
1.1.2.1
1.1.3
1.1.3.1
1.1.3.2
1.1.4
1.1.4.1
1.1.4.2
1.1.4.3
1.1.5
1.1.5.1
1.1.5.2
1.1.5.3
1.1.5.4
1.1.5.5
1.1.5.6
1.1.5.7
1.1.5.8
1.1.5.9
1.1.5.10
1.1.6
1.1.6.1
1.1.6.2
1.1.6.3
1.1.7
1.1.7.1
1.1.7.2
1.1.7.3
1.1.7.4
1.1.7.5
1.1.8
1.1.8.1
1.1.8.2
1.1.8.3
1.1.9
1.1.9.1
1.1.9.2
1.1.10
1.1.10.1
DN00211177
Issue 12B
Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
New Parameters in RNC RN7.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
ADJD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
AdjdSRBHopsId (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 177
ADJS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
SRBHopsIdentifier (SRB HOPS Identifier). . . . . . . . . . . . . . . . . . . . . . 177
CBCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
ETWSsupportEnabled (ETWS Support Enabled) . . . . . . . . . . . . . . . . 178
IUOIdentifier (IUO Object Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . 178
COSITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
COSITEChangeOrigin (COSITE Change origin) . . . . . . . . . . . . . . . . . 178
COSITEId (COSITE Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
SharingState (Sharing State) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
COSRNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
AdditionalStateInfo (Additional State Information) . . . . . . . . . . . . . . . . 179
AdminStateInfo (Admin State Info) . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
AdministrativeState (Administrative State). . . . . . . . . . . . . . . . . . . . . . 179
AvailabilityStatus (Availability Status) . . . . . . . . . . . . . . . . . . . . . . . . . 180
ClusterIfState (Cluster Interface State) . . . . . . . . . . . . . . . . . . . . . . . . 180
COSRNCChangeOrigin (COSRNC Change origin). . . . . . . . . . . . . . . 180
COSRNCId (COSRNC Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
OperationalState (Operational State ) . . . . . . . . . . . . . . . . . . . . . . . . . 181
PeerRNCIPAddress (Peer RNC IP Address). . . . . . . . . . . . . . . . . . . . 181
RNCOMConnState (RNC-RNC O&M Connection State) . . . . . . . . . . 181
IUCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
CNId (Core Network Identity). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
CSFlexiIuWeight (CS Flexible Iu Weight) . . . . . . . . . . . . . . . . . . . . . . 182
IUOIdentifier (IUO Object Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . 182
IUO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
CSCNDRXLength (CN CS domain specific DRX cycle length) . . . . . . 182
PSCNDRXLength (CN PS domain specific DRX cycle length) . . . . . . 183
IuBarringRecoveryTimerCS (Iu service barring recovery timer for CS) 183
IuBarringRecoveryTimerPS (Iu service barring recovery timer for PS) 183
IubTransportSharingInd (Iub Transport Sharing index) . . . . . . . . . . . . 184
IUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
CNId (Core Network Identity). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
IUOIdentifier (IUO Object Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . 184
PSFlexiIuWeight (PS Flexible Iu Weight). . . . . . . . . . . . . . . . . . . . . . . 185
IUR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
AppAwareRANEnabled (Application Aware RAN Enabled). . . . . . . . . 185
MaxFPDLFrameSizeIur (Maximum FP downlink frame size Iur) . . . . . 185
PFL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
PFLDBHSDAMR (Preferred Frequency Layer for DB-DC-HSDPA AMR) .
186
Id:0900d805809d7397
3
WCDMA Radio Network Configuration Parameters
1.1.10.2
1.1.10.3
1.1.10.4
1.1.10.5
1.1.10.6
1.1.10.7
1.1.10.8
1.1.11
1.1.11.1
1.1.11.2
1.1.11.3
1.1.11.4
1.1.11.5
1.1.11.6
1.1.11.7
1.1.11.8
1.1.11.9
1.1.11.10
1.1.11.11
1.1.11.12
1.1.11.13
1.1.11.14
1.1.11.15
1.1.11.16
1.1.11.17
1.1.11.18
1.1.11.19
1.1.11.20
1.1.11.21
1.1.11.22
4
PFLDBHSDAMRNRT (Preferred Frequency Layer for DB-DC-HSDPA
AMR and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
PFLDBHSDNRT (Preferred Frequency Layer for DB-DC-HSDPA NRT) . .
186
PFLDBHSDStr (Preferred Frequency Layer for DB-DC-HSDPA Streaming)
186
PFLDBHSDAMR/PrefLayerDBHSDAMR (Preferred Layer for DB-DC-HSDPA AMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
PFLDBHSDAMRNRT/PrefLayerDBHSDAMRNRT (Preferred Layer for
DB-DC-HSDPA AMR and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
PFLDBHSDNRT/PrefLayerDBHSDNRT (Preferred Layer for DB-DC-HSDPA NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
PFLDBHSDStr/PrefLayerDBHSDStr (Preferred Layer for DB-DC-HSDPA
Streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
RNAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
RNARDSACGuardTime (Access class restriction guard time) . . . . . . . 188
RNARDSACCell_DCH (Access class restriction level for Cell_DCH) . 188
RNARDSACCell_PCH (Access class restriction level for Cell_PCH) . . 189
AutoACRestForCellPCH (Access Restriction for Cell_PCH state UE) . 189
AutoACDecRestHysNRTQ (Automatic Access Class Decrease Restriction
Level Hysteresis for NRT queue length trigger) . . . . . . . . . . . . . . . . . . 189
AutoACDecRestHysRTWP (Automatic Access Class Decrease Restriction
Level Hysteresis for Received Total Wideband Power trigg) . . . . . . . . 189
AutoACIncRestHysNRTQ (Automatic Access Class Increase Restriction
Level Hysteresis for NRT queue length trigger) . . . . . . . . . . . . . . . . . . 190
AutoACIncRestHysRTWP (Automatic Access Class Increase Restriction
Level Hysteresis for Received Total Wideband Powertrigge) . . . . . . . . 190
AutoACMaxRestLevel (Automatic Access Class Maximum Restriction Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
AutoACRLevelUpdInt (Automatic Access Class Restriction Level Update
Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
AutoACRTrigRNCLoad (Automatic Access Class Restriction Trigger of
RNC Load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
DynHSUPABLERThrBurstyTP (Bursty Data throughput threshold per TTI)
191
DynHSUPABurstyPeriod (Bursty Period for Dyn HSUPA BLER) . . . . . 191
ULFastOLPCDTXthld (DTX threshold for uplink faster outer loop). . . . 192
FOLPCSIRTgtModInt (Faster OLPC SIR target modification interval) . 192
FOLPCStepSizSIRTgt (Faster OLPC step size of SIR target changes) 192
L1BurstDataBLERTrgtEDCH (Layer1 Bursty Data BLER target for E-DCH)
193
L1ContBLERTrgtEDCH10 (Layer1 Continuous BLER target for E-DCH TTI
10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
L1ContBLERTrgtEDCH2 (Layer1 Continuous BLER target for E-DCH TTI
2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
L1PeakRateBLERTrgtEDCH (Layer1 Peak Data Rate BLER target for EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
PagingRestrictionInd (Paging Restriction Indication for PPAC) . . . . . . 194
DynHSUPABLERMaxRateThrC10 (Peak rate thr for cont data of Dyn HSUPA BLER 10 ms TTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.11.23
1.1.11.24
1.1.11.25
1.1.11.26
1.1.11.27
1.1.11.28
1.1.11.29
1.1.11.30
1.1.11.31
1.1.11.32
1.1.11.33
1.1.11.34
1.1.11.35
1.1.11.36
1.1.11.37
1.1.11.38
1.1.11.39
1.1.12
1.1.12.1
1.1.12.2
1.1.12.3
1.1.12.4
1.1.12.5
1.1.12.6
1.1.12.7
1.1.12.8
1.1.12.9
1.1.12.10
1.1.12.11
1.1.12.12
1.1.12.13
DN00211177
Issue 12B
DynHSUPABLERMaxRateThrC2 (Peak rate thr for cont data of Dyn HSUPA BLER 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
DynHSUPABLERMaxRateThrB (Peak rate threshold for bursty data of Dyn
HSUPA BLER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
PTTUEMappingARPCap (PTT UE mapping for ARP pre-emption capability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
PTTUEMappingARPVul (PTT UE mapping for ARP pre-emption vulnerability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
PTTUEMappingARPPrioLevel (PTT UE mapping for ARP priority level) .
196
PTTUEMappingARPQue (PTT UE Mapping for ARP queuing allowed) . .
197
PTTUEMappingSignInd (PTT UE mapping for Signaling indication) . . 197
PTTUEMappingTC (PTT UE mapping for Traffic Class) . . . . . . . . . . . 198
PTTUEMappingTHP (PTT UE mapping for Traffic handling priority). . 198
RAU_LAU_RestrictionInd (RAU and LAU Restriction Indication for PPAC)
199
DynHSUPABLERBurstDataRx (Retransmissions in Dyn HSUPA BLER for
Bursty Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
DynHSUPABLERContDataRx10 (Retransmissions in Dyn HSUPA BLER
for Cont Data 10msTTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
DynHSUPABLERContDataRx2 (Retransmissions in Dyn HSUPA BLER for
Cont Data 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
DynHSUPABLERPeakRateRx (Retransmissions in Dyn HSUPA BLER for
Peak data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
RRCConnSetupMsgSize (RRC Connection Setup Message Size Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
DynHSUPABLERAlgTrgTime (Time to trigger Dyn HSUPA BLER Algorithm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
DynHSUPABLERFrameWinSiz (Window size for FP Frames Measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
RNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
AlarmSetforWCELBLINIT (Alarm Set for WCEL BL-INIT) . . . . . . . . . . 202
DSCPStatisticsGroupTCPack (DSCP code for DL TCP Ack statistics) 202
DSCPStatisticsGroupA (DSCP statistics group A ) . . . . . . . . . . . . . . . 202
DSCPStatisticsGroupB (DSCP statistics group B) . . . . . . . . . . . . . . . 202
DSCPStatisticsGroupC (DSCP statistics group C) . . . . . . . . . . . . . . . 203
MACLogicalChPriority (MAC logical channel priority definition) . . . . . 203
MACLogicalChPriority/MACLogChPriSRB1 (MAC logical channel priority
for SRB1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
MACLogicalChPriority/MACLogChPriSRB2 (MAC logical channel priority
for SRB2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
MACLogicalChPriority/MACLogChPriSRB3 (MAC logical channel priority
for SRB3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
RncClientTLSMode (RNC Client TLS Mode). . . . . . . . . . . . . . . . . . . . 204
CBCSourceIPAddress (Source IP address for IuBC interface) . . . . . . 204
UePeriodicMeasCpuLimit (UE Periodic Measurement Report CPU Limit)
204
UePeriodicMeasInterval (UE Periodic Measurement Report Measurements Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Id:0900d805809d7397
5
WCDMA Radio Network Configuration Parameters
1.1.12.14
1.1.13
1.1.13.1
1.1.13.2
1.1.13.3
1.1.13.4
1.1.13.5
1.1.13.6
1.1.13.7
1.1.13.8
1.1.13.9
1.1.13.10
1.1.13.11
1.1.13.12
1.1.13.13
1.1.13.14
1.1.14
1.1.14.1
1.1.14.2
1.1.14.3
1.1.14.4
1.1.14.5
1.1.14.6
1.1.14.7
1.1.14.8
1.1.14.9
1.1.14.10
1.1.14.11
1.1.14.12
1.1.14.13
1.1.14.14
1.1.14.15
1.1.14.16
1.1.14.17
1.1.14.18
1.1.14.19
1.1.14.20
1.1.14.21
1.1.14.22
1.1.14.23
6
WCELIdleAlarmTimeout (WCEL Idle Alarm Timeout) . . . . . . . . . . . . . 205
RNFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
AutoACResEnabled (Automatic Access Class Restriction Enabled) . . 205
CSFBEnabled (CSFB Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
DCH00SuppOnIurEnabled (DCH 0/0 Support On Iur Enabled) . . . . . . 206
DCHtoPCHEnabled (Enabling direct Cell_DCH to PCH state transition) . .
206
FastPCHSwitchEnabled (Enabling Fast Cell_PCH Switching feature) . 206
FasterOLPCEnabled (Faster OLPC Enabled) . . . . . . . . . . . . . . . . . . . 206
FemtoHandoverControl (Femto Handover Control) . . . . . . . . . . . . . . . 207
FlexULRLCEnabled (Flexible UL RLC Enabled) . . . . . . . . . . . . . . . . . 207
HSUPADynBLEREnabled (HSUPA Dynamic BLER Enabled) . . . . . . . 207
IFHOOverIurExt (IFHO Over Iur Extension) . . . . . . . . . . . . . . . . . . . . . 207
LFDProfEnabled (LFD profiling Enabled) . . . . . . . . . . . . . . . . . . . . . . . 208
PPACEnabled (Paging Permission With Access Control Enabled) . . . 208
PTTEnabled (Push to talk enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
SRVCCEnabled (SRVCC Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
RNHSPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
AARConfigTable (Application Aware RAN Configuration Table) . . . . . 209
AARConfigTable/AppGrpId (Application Group Identifier) . . . . . . . . . . 210
AARConfigTable/DSCPCode1 (DSCP Code1). . . . . . . . . . . . . . . . . . . 210
AARConfigTable/DSCPCode2 (DSCP Code2). . . . . . . . . . . . . . . . . . . 211
AARConfigTable/DSCPCode3 (DSCP Code3). . . . . . . . . . . . . . . . . . . 211
AARConfigTable/DSCPCode4 (DSCP Code4). . . . . . . . . . . . . . . . . . . 212
AARConfigTable/DSCPCode5 (DSCP Code5). . . . . . . . . . . . . . . . . . . 212
VCPHSDPAPrevDuration (Duration of HSDPA prevention for Voice Call
Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
MaxEHARQReTxPSconv10 (E-DCH max number of retransmissions PS
conv E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
MaxEHARQReTxPSconv2 (E-DCH max number of retransmissions PS
conv E-TTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
PowerOffsetEHARQPSConv (HARQ power offset for E-DCH MAC-d flow
of PS conv) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
DiscardTimerPTT (HSDPA Discard Timer for the PTT) . . . . . . . . . . . . 214
T1PTT (HSDPA re-ordering rel timer T1 for the PTT) . . . . . . . . . . . . . 214
VCPHSDPAUserIncr (HSDPA user increment for the Voice Call Priority) .
214
MEHHSUPAUserIncr (HSUPA user increment for the Mass Event Handler)
215
InitialSPINRT (Initial SPI for PS NRT RAB) . . . . . . . . . . . . . . . . . . . . . 215
AARConfigTable/Precedence (Precedence) . . . . . . . . . . . . . . . . . . . . 215
PTTRLCPDUSizeHSDSCH (RLC PDU size for PTT mapped to HS-DSCH)
216
AARConfigTable/TargetSPIforSPI0 (Target SPI for SPI 0) . . . . . . . . . 216
AARConfigTable/TargetSPIforSPI1 (Target SPI for SPI 1) . . . . . . . . . 216
AARConfigTable/TargetSPIforSPI10 (Target SPI for SPI 10) . . . . . . . 217
AARConfigTable/TargetSPIforSPI11 (Target SPI for SPI 11) . . . . . . . 217
AARConfigTable/TargetSPIforSPI2 (Target SPI for SPI 2 ) . . . . . . . . . 218
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.14.24
1.1.14.25
1.1.14.26
1.1.14.27
1.1.14.28
1.1.14.29
1.1.14.30
1.1.14.31
1.1.14.32
1.1.14.33
1.1.15
1.1.15.1
1.1.15.2
1.1.16
1.1.16.1
1.1.16.2
1.1.16.3
1.1.16.4
1.1.17
1.1.17.1
1.1.17.2
1.1.17.3
1.1.17.4
1.1.17.5
1.1.17.6
1.1.17.7
1.1.17.8
1.1.17.9
1.1.17.10
1.1.17.11
1.1.17.12
1.1.17.13
DN00211177
Issue 12B
AARConfigTable/TargetSPIforSPI3 (Target SPI for SPI 3 ) . . . . . . . . 218
AARConfigTable/TargetSPIforSPI4 (Target SPI for SPI 4) . . . . . . . . . 219
AARConfigTable/TargetSPIforSPI5 (Target SPI for SPI 5) . . . . . . . . . 219
AARConfigTable/TargetSPIforSPI6 (Target SPI for SPI 6) . . . . . . . . . 220
AARConfigTable/TargetSPIforSPI7 (Target SPI for SPI 7) . . . . . . . . . 220
AARConfigTable/TargetSPIforSPI8 (Target SPI for SPI 8) . . . . . . . . . 221
AARConfigTable/TargetSPIforSPI9 (Target SPI for SPI 9) . . . . . . . . . 221
MEHCQIFeedbackCycle (Temporary CQI feedback cycle for the Mass
Event Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
SmartHSPATimeToTrigger (Time-to-trigger for Smartphone throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
SmartHSPATputAveWin (Window size for Smartphone throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
RNMOBI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
SmartLTELayeringServ (Smart LTE Layering service control) . . . . . . 222
SmartLTELayeringPrevT (Timer for Smart LTE Layering Prevention) 223
RNPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
SmartInactTimerFACH (Inactivity Timer for Smart Phones in Cell_FACH)
223
SmartInactivityTimerDCH (Inactivity timer for Smartphone DCH) . . . . 223
PTTDormancyTimer (PTT dormancy timer). . . . . . . . . . . . . . . . . . . . . 224
MEHTVMPendingTime (Temporary TVM pending time for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
RNRLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
AMRLCHSRACHPS (AM RLC configuration for PS NRT with HS-RACH)
224
AMRLCHSRACHPS/AMRLCHSRACHPSMaxDAT (AM RLC MaxDAT
transmissions for PS NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . 225
AMRLCHSRACHPS/AMRLCHSRACHPSMaxMRW (AM RLC MaxMRW
transmissions for PS NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . 225
AMRLCHSRACHPS/AMRLCHSRACHPSMaxRST (AM RLC MaxRST
transmissions for PS NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . 226
AMRLCHSRACHPS/AMRLCHSRACHPSPollPDU (AM RLC period
Poll_PDU for PS NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . 226
AMRLCRTTPollPDUSatellite (AM RLC period Poll_PDU with satellite Iub)
226
AMRLCHSRACHPS/AMRLCHSRACHPSPollSDU (AM RLC period
Poll_SDU for PS NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . 227
AMRLCHSRACHPS/AMRLCHSRACHPSPollWin (AM RLC period
Poll_Window for PS NRT with HS-RACH). . . . . . . . . . . . . . . . . . . . . . 227
AMRLCSRB3n4RespTime (AM RLC round trip time for SRB3 and SRB4)
227
AMRLCRespTimeHSSRB (AM RLC round trip time for SRBs with HS-RACH/HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
AMRLCHSRACHPS/HSRACHAMRLCRespHSFACH (AM RLC round trip
time with HS-RACH/HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
AMRLCHSRACHPS/AMRLCHSRACHPSPeriodMax (AM RLC status period max for PS NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . 228
AMRLCSRB3n4PeriodMax (AM RLC status period max for SRB3 and
SRB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
Id:0900d805809d7397
7
WCDMA Radio Network Configuration Parameters
1.1.17.14
1.1.17.15
1.1.17.16
1.1.17.17
1.1.17.18
1.1.17.19
1.1.18
1.1.18.1
1.1.18.2
1.1.18.3
1.1.18.4
1.1.18.5
1.1.18.6
1.1.18.7
1.1.18.8
1.1.18.9
1.1.19
1.1.19.1
1.1.19.2
1.1.19.3
1.1.19.4
1.1.19.5
1.1.19.6
1.1.19.7
1.1.19.8
1.1.19.9
1.1.20
1.1.20.1
1.1.20.2
1.1.20.3
1.1.21
1.1.21.1
1.1.21.2
1.1.21.3
1.1.21.4
1.1.21.5
8
AMRLCPeriodMaxHSSRB (AM RLC status period max for SRBs with HSRACH/HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
AMRLCHSRACHPS/AMRLCHSRACHPSPeriodMin (AM RLC status period min for PS NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
AMRLCHSRACHPS/AMRLCHSRACHPSTriggers (AM RLC status report
triggers for PS NRT with HS-RACH). . . . . . . . . . . . . . . . . . . . . . . . . . . 230
AMRLCOnDCHSRB136OffSat (AM RLC timer offset for SRB13.6 with satellite DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
RLCConfOptionFPS (RLC Conf option switch for Fast Cell_PCH Switching) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
UMRLCPTTDiscardTime (UM RLC SDU discard time in UE for PTT) . 231
RNTRM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
ActivityFactorForHSPA/AfPTTDL (Activity Factor for PTT RAB in Downlink) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
ActivityFactorForHSPA/AfPTTUL (Activity Factor for PTT RAB in Uplink) .
232
DSCPBTSOMToBTS (DSCP for BTS OM towards BTS) . . . . . . . . . . . 232
DSCPBTSOMToOMS (DSCP for BTS OM towards OMS). . . . . . . . . . 232
DSCPForGTPSignalling (DSCP for GTP signalling). . . . . . . . . . . . . . . 232
RespSyncModEnableIP (IP Iub DCH Sync Modifiable) . . . . . . . . . . . . 233
RespSyncTimerIP (IP Response synchronization timer for DL synch
frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
RespSyncTimerSatIP (IP Response synchronization timer with Satellite
Iub) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
RespSyncCounterIP (Response synchronization counter for DL synch
frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
VCEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . . . 233
FastActOfTargetServCell (Faster Activation Of Target Serving Cell) . . 234
FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . . . 234
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . . . 234
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay) . . 235
HSPASCCSpecificATO (HSPA SCC Specific ATO Value). . . . . . . . . . 235
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
SRBHopsIdentifier (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . 236
WACSetIdentifier (WAC Parameter Set Identifier) . . . . . . . . . . . . . . . . 236
WAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
InactHSRACH (Inactive HS-RACH capable UE) . . . . . . . . . . . . . . . . . 236
WACChangeOrigin (WAC Change origin) . . . . . . . . . . . . . . . . . . . . . . 236
WACId (WAC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
WBTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
RRMULDCHActivityFactor/RRMULActivityFactorPTT (Average relative
UL data rate for RBs of PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
PWSMEnableWakeUpTime (Enable cell activation based on time of day)
237
HSUPACCEnabled (HSUPA Congestion Control activation) . . . . . . . . 237
IPBasedRouteIdIub3 (IP Based Route Id Iub 3) . . . . . . . . . . . . . . . . . . 238
IPBasedRouteIdIub4 (IP Based Route Id Iub 4) . . . . . . . . . . . . . . . . . . 238
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.21.6
1.1.21.7
1.1.21.8
1.1.21.9
1.1.21.10
1.1.21.11
1.1.21.12
1.1.22
1.1.22.1
1.1.22.2
1.1.22.3
1.1.22.4
1.1.22.5
1.1.22.6
1.1.22.7
1.1.22.8
1.1.22.9
1.1.22.10
1.1.22.11
1.1.22.12
1.1.22.13
1.1.22.14
1.1.22.15
1.1.22.16
1.1.22.17
1.1.22.18
1.1.22.19
1.1.22.20
1.1.22.21
1.1.22.22
1.1.22.23
1.1.22.24
1.1.22.25
1.1.22.26
1.1.22.27
1.1.22.28
1.1.22.29
1.1.22.30
DN00211177
Issue 12B
IubTransportSharing (Iub Transport Sharing activation) . . . . . . . . . . . 238
MaxFPDLFrameSizeIub (Maximum FP downlink frame size Iub) . . . . 239
TQMId2 (TQM Object Identifier 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
TQMId3 (TQM Object Identifier 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
TQMId4 (TQM Object Identifier 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
PWSMAVTrafficVERLogic (Traffic verification logic in PWSM cell activation process) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
WBTSSWBuildId (WBTS SW build identifier) . . . . . . . . . . . . . . . . . . . 241
WCEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
HSRACHTransmisBackOff (Additional E-DCH transmission back off for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
AppAwareRANCapability (Application Aware RAN Capability) . . . . . . 241
AppAwareRANEnabled (Application Aware RAN Enabled). . . . . . . . . 242
AutoACResULOLThr (Automatic Access Class Restriction Uplink Overload Threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
AutoACRPrxTotalAvgWs (Automatic Access Class window size for averaging PrxTotal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
HSRACHSubChannelNumber (Available Sub Channel Number for HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No). 243
CodeTreeOptimisationGuardTime (Code Tree Optimisation Guard Time)
243
HSRACHImplicitRelease (Common E-DCH implicit release for HS-RACH)
243
HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell)
244
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
DefMeasCtrlReading (Deferred Measurement Control Reading) . . . . 245
DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . . . 245
DRXCycleHSFACH (Discontinuous Reception Cycle HS-FACH) . . . . 245
HSFACHVolThrDLPTT (DL traffic volume measurement threshold of HSFACH for PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
SmartTrafVolThrDL (DL traffic volume threshold for Smartphone) . . . 246
AutoACDSACRestriction (Domain Specific Access Class Restriction) 246
DRXInterruptHSDSCHData (DRX Interruption by HS-DSCH data). . . 246
DBandHSDPAEnabled (Dual Band HSDPA Enabled). . . . . . . . . . . . . 247
FastHSPAMobilityEnabled (Fast HSPA Mobility Enabled) . . . . . . . . . 248
FastActOfTargetServCell (Faster Activation Of Target Serving Cell) . 249
FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . . . 249
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . . 250
SRBHSPAFmcsId (FMCS identifier for standalone SRB on HSPA) . . 250
HappyBitDelayConHSRACH (Happy bit delay condition for HS-RACH) . .
250
T321 (High Speed Cell FACH DRX operation timer) . . . . . . . . . . . . . . 250
HSFACHCapability (High Speed FACH Capability). . . . . . . . . . . . . . . 250
HSRACHCapability (High Speed RACH Capability) . . . . . . . . . . . . . . 251
HSRACHEnabled (High Speed RACH Enabled) . . . . . . . . . . . . . . . . . 251
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay). . 251
Id:0900d805809d7397
9
WCDMA Radio Network Configuration Parameters
1.1.22.31
1.1.22.32
1.1.22.33
1.1.22.34
1.1.22.35
1.1.22.36
1.1.22.37
1.1.22.38
1.1.22.39
1.1.22.40
1.1.22.41
1.1.22.42
1.1.22.43
1.1.22.44
1.1.22.45
1.1.22.46
1.1.22.47
1.1.22.48
1.1.22.49
1.1.22.50
1.1.22.51
1.1.22.52
1.1.22.53
1.1.22.54
1.1.22.55
1.1.22.56
1.1.22.57
1.1.22.58
1.1.22.59
1.1.22.60
1.1.22.61
10
RXBurstHSFACH (HS-FACH Reception Burst) . . . . . . . . . . . . . . . . . . 251
AmpliRatioOptHSRACH (HS-RACH amplitude ratio optimized for low/high
bit rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
HSRACHMPO (HS-RACH Measurement Power Offset) . . . . . . . . . . . 252
MEHHSDPAUserNbrCQI (HSDPA CQI user number for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
HSFACHRABDRAEnabled (HSFACH direct resource allocation for NRT
HSPA RAB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
HSFACHRel8ConSetupEC (HSFACH Rel8UE EstCause mapping in RRC
con setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
HSPA128UsersPerCell (HSPA 128 Users per Cell) . . . . . . . . . . . . . . . 253
HSPASCCSpecificATO (HSPA SCC Specific ATO Value). . . . . . . . . . 254
MEHHSUPAUserNbr2msTTI (HSUPA E-DCH 2 ms TTI user number for
the Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
DRXInactiveTimerHSFACH (Inactivity Supervision Timer of HS-FACH for
DRX User ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
LayeringRRCRelEnabled (Layering in RRC Connection Release Enabled)
255
MEHLoadStateTtT (Load state time-to-trigger for the Mass Event Handler)
255
MassEventHandler (Mass Event Handler functions) . . . . . . . . . . . . . . 256
HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
HSRACHMaxPeriodCollis (Max period for collision resolution phase for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
PrxTargetPSMaxtHSRACH (Max PS target interference level with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
PtxTargetPSMaxtHSRACH (Max PS target power level with HS-RACH) .
257
HSRACHMaxAllocTimeCCCH (Maximum E-DCH resource alloc time for
CCCH for HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
HSRACHMaxTotSymbolRate (Maximum total uplink symbol rate of the
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
MBLBLoadInfoDistr (MBLB Load Information Distribution). . . . . . . . . . 258
HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
HSRACHCommonEDCHRes (Number of Common E-DCH Resources for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
ActivationTimeOffset (Offset for activation time). . . . . . . . . . . . . . . . . . 259
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA). . . . 260
OffsetToBeginCTCHBSIndex (Offset to Begin CTCH Block Set Index) 260
PowerOffsetPreamHSRACH (Power Offset Last Transmitted Preamble for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No) . 261
MEHQueueThreshold (Scheduling queue threshold for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
SABEnabled (Service Area Broadcast Enabled) . . . . . . . . . . . . . . . . . 262
SmartLTELayeringEnabled (Smart LTE Layering Enabled) . . . . . . . . . 262
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.62
1.1.22.63
1.1.22.64
1.1.22.65
1.1.22.66
1.1.22.67
1.1.22.68
1.1.22.69
1.1.22.70
1.1.22.71
1.1.22.72
1.1.22.73
1.1.22.74
1.1.22.75
1.1.22.76
1.1.22.77
1.1.22.78
1.1.22.79
1.1.22.80
1.1.22.81
1.1.22.82
1.1.23
1.1.23.1
1.1.23.2
1.1.23.3
1.1.23.4
1.1.23.5
1.1.23.6
1.1.23.7
DN00211177
Issue 12B
SmartLTELayeringUA (Smart LTE Layering NRT user amount threshold)
263
SmartLTELayeringRSCP (Smart LTE Layering RSCP threshold). . . . 263
SmartLTELayeringTSysSel (Smart LTE Layering Target System Selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
LayeringRRCConnRelTargFreq/TargetFrequency (Target frequency) 264
LayeringRRCConnRelTargFreq (Target frequency for layering in RRC
Connection Release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
VCPMaxHSDPAUsers (Temporary max number of HSDPA users for the
VCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
MEHMaxHSUPAUsers (Temporary max number of HSUPA users for the
Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
HSRACHActivityThr (Threshold of the E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
HSRACHActTimeToTrigger (Time to trigger for activity measurement on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
HSRACHTimeToTrigger (Traffic volume measurement time to trigger of
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
UEDRXCapability (UE DRX in Cell_FACH capability). . . . . . . . . . . . . 266
HSFACHDRXEnabled (UE DRX with High Speed Cell FACH Enabled) . .
266
UePeriodicMeasEnabled (UE Periodic Measurement Report Enabled) 266
MEHULLHSDPAUALimit (UL load based HSDPA user amount limit for the
MEH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
HSRACHVolThrUL (UL traffic volume measurement threshold of HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
SmartTrafVolThrUL (UL traffic volume threshold for Smartphone) . . . 268
HSRACHExtendedAI (Use of Extended Acquisition Indicator HS-RACH).
268
VoiceCallPriority (Voice Call Prioritisation During High Traffic Load) . 268
VCPPtxOffset (Voice Call Priority target threshold for HSDPA prevention)
269
WACSetIdentifier (WAC Parameter Set Identifier). . . . . . . . . . . . . . . . 269
HSRACHActivityAveWin (Window size of E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269
WRAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
L1BLERTEDCHPSConvSpe10 (BLER target for PS Conversational
speech E-TTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
L1BLERTEDCHPSConvSpe2 (BLER target for PS Conversational speech
E-TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
EbNoDCHRateGain/EbNoDCHRateGainPSConvSpe (Data rate gain for
the Eb/N0 of the PS conv speech). . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
EbNoEDCHPSConvSpeech (Eb/N0 planned for E-DCH PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
EDCHBLERAdjPSConvSpe10 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 10 ms). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
EDCHBLERAdjPSConvSpe2 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 2 ms). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
SIRDPCCHInitialEDCH (Initial SIR target for UL DPCCH with E-DCH) 273
Id:0900d805809d7397
11
WCDMA Radio Network Configuration Parameters
1.1.23.8
1.1.23.9
1.1.23.10
1.1.23.11
1.1.23.12
1.1.23.13
1.2
1.2.1
1.2.1.1
1.2.2
1.2.2.1
1.2.2.2
1.2.3
1.2.3.1
1.2.3.2
1.2.3.3
1.2.3.4
1.2.3.5
1.2.3.6
1.2.3.7
1.2.4
1.2.4.1
1.2.5
1.2.5.1
1.2.5.2
1.2.5.3
1.2.5.4
1.2.5.5
1.2.5.6
1.2.5.7
1.2.6
1.2.6.1
1.2.6.2
1.2.7
1.2.7.1
1.2.7.2
1.2.8
1.2.8.1
1.2.8.2
12
SIRDPCCHInitialEDCH/SIRDPCCHInitialEDCHPTT10MS (Initial SIR target for UL DPCCH with E-TTI 10 ms - PTT) . . . . . . . . . . . . . . . . . . . . . 273
SIRDPCCHInitialEDCH/SIRDPCCHInitialEDCHPTT2MS (Initial SIR target
for UL DPCCH with E-TTI 2 ms - PTT) . . . . . . . . . . . . . . . . . . . . . . . . . 274
EbNoOfPSConvSpe/EbNoDCHOfPSConvSpe (Planned Eb/N0 of the PS
conversational speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
EbNoOfPSConvSpe/EbNoDCHOfPSConvSpeQua (Quality target of the
PS conversational speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
EbNoOfPSConvSpe (Rate matching with the PS conversational speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
SIRDPCCHInitialDCH/SIRDPCCHInitialDCHPSConvSpe (UL SIR target
regardless of DL channel - PS conv speech) . . . . . . . . . . . . . . . . . . . . 275
Changed parameters in RNC RN7.0 . . . . . . . . . . . . . . . . . . . . . . . . . . 276
ADJD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
AdjdRTWithHSDPAHopsId (HSDPA HOPS identifier for speech services)
276
ADJG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
AdjgSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . 277
ADJGId (Inter-system adjacency identifier) . . . . . . . . . . . . . . . . . . . . . 279
ADJI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
BlindHOTargetCell (Blind HO target cell) . . . . . . . . . . . . . . . . . . . . . . . 279
AdjiCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
AdjiSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . . 280
AdjiMCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
AdjiMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
AdjiMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . 282
AdjiRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
ADJL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
AdjLEARFCN (E-UTRA Absolute Radio Frequency Channel Number) 283
ADJS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
AdjsCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
RTWithHSDPAHopsIdentifier (HSDPA HOPS identifier for speechservices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
AdjsSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . 285
AdjsMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
AdjsMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
AdjsMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 287
AdjsRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
CBCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
CBCIPaddress (IP address of the CBC) . . . . . . . . . . . . . . . . . . . . . . . . 288
CBCIPaddrType (Type of CBC IP address) . . . . . . . . . . . . . . . . . . . . . 288
CMOB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
CMOBId (Congestion Management Group Identifier). . . . . . . . . . . . . . 289
TrafficRestriction (Traffic Restriction) . . . . . . . . . . . . . . . . . . . . . . . . . . 289
COCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
AAL2TP/AAL2SignLinkVCI (AAL2 signalling link Virtual Channel Identifier)
289
AAL2SignLinkTP/AAL2SigEarlyPacketDiscard (AAL2 SL Early Packet Discard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.8.3
1.2.8.4
1.2.8.5
1.2.8.6
1.2.8.7
1.2.8.8
1.2.8.9
1.2.8.10
1.2.8.11
1.2.8.12
1.2.8.13
1.2.8.14
1.2.8.15
1.2.8.16
1.2.8.17
1.2.9
1.2.9.1
1.2.10
1.2.10.1
1.2.11
1.2.11.1
1.2.11.2
1.2.12
1.2.12.1
1.2.13
1.2.13.1
1.2.13.2
1.2.13.3
1.2.13.4
1.2.13.5
1.2.13.6
1.2.13.7
1.2.13.8
1.2.14
1.2.14.1
1.2.14.2
1.2.14.3
1.2.15
1.2.15.1
1.2.15.2
1.2.15.3
1.2.15.4
DN00211177
Issue 12B
AAL2SignLinkTP/AAL2SigPartialPacketDiscard (AAL2 SL Partial Packet
Discard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
CNBAPTP/CNBAPEarlyPacketDiscard (C-NBAP Early Packet Discard) .
290
CNBAPTP/CNBAPPartialPacketDiscard (C-NBAP Partial Packet Discard)
290
CNBAPTP/CNBAPCDVT01Ing (C-NBAP VCLtp CDVT ingress) . . . . 290
CNBAPTP/CNBAPVCI (C-NBAP Virtual Channel Identifier) . . . . . . . . 290
CNBAPTP/CNBAPVPI (C-NBAP Virtual Path Identifier) . . . . . . . . . . . 290
DNBAPTP/DNBAPEarlyPacketDiscard (D-NBAP Early Packet Discard) .
291
DNBAPTP/DNBAPVCI (D-NBAP Virtual Channel Identifier) . . . . . . . . 291
DNBAPTP/DNBAPVPI (D-NBAP Virtual Path Identifier) . . . . . . . . . . . 291
DNBAPTP/DNBAPPartialPacketDiscard (DNBAP Partial Packet Discard)
291
VPLTP (Virtual Path Link termination point) . . . . . . . . . . . . . . . . . . . . 291
VPLTP/VPLTPCDVT01Egr (VPLtp CDVT egress) . . . . . . . . . . . . . . . 291
VPLTP/VPLTPAdmState (VPLtp effective administrative state) . . . . . 292
VPLTP/VPLTPPCR01Egr (VPLtp PCR egress) . . . . . . . . . . . . . . . . . 292
VPLTP/VPLTPTrafficShaping (VPLtp VP level traffic shaping) . . . . . . 292
FMCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
IMSIbasedGsmHo (IMSI Based GSM HO) . . . . . . . . . . . . . . . . . . . . . 292
HOPG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
AdjgPriorityCoverage (Ncell Priority for Coverage HO) . . . . . . . . . . . . 293
HOPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
AdjiPriorityCoverage (Ncell Priority for Coverage IFHO) . . . . . . . . . . . 293
AdjiPriorityQuality (Ncell Priority for Quality IFHO) . . . . . . . . . . . . . . . 294
HOPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
HSDPAAvailabilityIur (HSDPA availability of the neighbouring DRNC cell)
294
IPQM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
BackgroundTCToDSCP (Background TC to DSCP mapping). . . . . . . 294
IPQMChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 294
ConversationalTCToDSCP (Conversational TC to DSCP mapping) . . 295
InteractiveTHP1TCToDSCP (Interactive THP1 TC to DSCP mapping) 295
InteractiveTHP2TCToDSCP (Interactive THP2 TC to DSCP mapping) 295
InteractiveTHP3TCToDSCP (Interactive THP3 TC to DSCP mapping) 295
IPQMId (IP Qos Management Identifier) . . . . . . . . . . . . . . . . . . . . . . . 295
StreamingTCToDSCP (Streaming TC to DSCP mapping) . . . . . . . . . 296
IUCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
NetworkInd (Network indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . . 296
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . . 297
IUCSIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
DestIPAddressCS (IP address for the IUCS destination subnet) . . . . 298
IPBasedRouteIdCS (IP Based Route Identifier for IUCS) . . . . . . . . . . 299
IPNetmaskCS (IP netmask for the IUCS destination subnet) . . . . . . . 300
IPQMIdCS (IPQM object id for IuCS). . . . . . . . . . . . . . . . . . . . . . . . . . 301
Id:0900d805809d7397
13
WCDMA Radio Network Configuration Parameters
1.2.16
1.2.16.1
1.2.16.2
1.2.16.3
1.2.16.4
1.2.16.5
1.2.16.6
1.2.16.7
1.2.16.8
1.2.16.9
1.2.16.10
1.2.16.11
1.2.16.12
1.2.16.13
1.2.17
1.2.17.1
1.2.17.2
1.2.17.3
1.2.17.4
1.2.17.5
1.2.18
1.2.18.1
1.2.18.2
1.2.18.3
1.2.18.4
1.2.18.5
1.2.19
1.2.19.1
1.2.19.2
1.2.19.3
1.2.19.4
1.2.19.5
1.2.19.6
1.2.19.7
1.2.19.8
1.2.19.9
1.2.19.10
1.2.19.11
1.2.19.12
1.2.19.13
1.2.19.14
14
IUO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
PLMNid/MCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . 301
PLMNid/MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . 302
PLMNid/MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . 302
NRILengthForCSCN (NRI length for CS Core Networks) . . . . . . . . . . . 302
NRILengthForPSCN (NRI length for PS Core Networks) . . . . . . . . . . . 303
NullNRIForCSPool (Null NRI value for CS Pool) . . . . . . . . . . . . . . . . . 303
NullNRIForPSPool (Null NRI value for PS Pool). . . . . . . . . . . . . . . . . . 304
OperatorWeight (Operator Weight). . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
PLMNid (PLMN identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
SharedAreaPLMNid/SharedAreaMCC (Shared area Mobile Country Code)
306
SharedAreaPLMNid/SharedAreaMNC (Shared area Mobile Network
Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
SharedAreaPLMNid/SharedAreaMNClength (Shared area Mobile Network
Code Length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
SharedAreaPLMNid (Shared area PLMN identity) . . . . . . . . . . . . . . . . 308
IUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
PSCNNRI/NRIMaxForPSCN (Maximum value of NRI range for PS Core
routing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
PSCNNRI/NRIMinForPSCN (Minimum value of NRI range for PS Core
routing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
NetworkInd (Network indicator). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . . 309
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . . . 310
IUPSIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
DestIPAddressPS (IP address for the IUPS destination subnet) . . . . . 311
IPBasedRouteIdPS (IP Based Route Identifier for IUPS) . . . . . . . . . . . 312
IPNetmaskPS (IP netmask for the IUPS destination subnet) . . . . . . . . 313
IPQMIdPS (IPQM object id for IuPS) . . . . . . . . . . . . . . . . . . . . . . . . . . 314
IUPSIPId (IUPSIP Identifier ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
IUR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
HSDPACCEnabledIur (HSDPA Congestion Control activation Iur) . . . 315
HSPAOverIur (HSPA over Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
IBTSSharing (IBTS Sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
MaxIurNRTHSDSCHBitRate (Maximum NRT HS-DSCH MAC-d flow bit
rate over Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
NeighbouringPLMNid/MCC (Mobile Country Code) . . . . . . . . . . . . . . . 316
NeighbouringPLMNid/MNC (Mobile Network Code) . . . . . . . . . . . . . . . 316
NeighbouringPLMNid/MNCLength (Mobile Network Code Length) . . . 317
NRncId (Neighbour RNC identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
NRncNetworkInd (Network indicator of neighbour RNC) . . . . . . . . . . . 318
OverbookingSwitchIur (Overbooking Switch Iur) . . . . . . . . . . . . . . . . . 318
NRncVersion (Release version of Neighbouring RNC) . . . . . . . . . . . . 318
NRncRelocationSupport (Serving RNC Relocation Support of neighbour
RNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
NRncSignPointCode (Signalling point code of neighbour RNC). . . . . . 319
NeighbouringRNWElement (Type of the Neighbouring RNW Element) 319
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.19.15
1.2.20
1.2.20.1
1.2.20.2
1.2.21
1.2.21.1
1.2.22
1.2.22.1
1.2.22.2
1.2.22.3
1.2.22.4
1.2.22.5
1.2.23
1.2.23.1
1.2.23.2
1.2.23.3
1.2.23.4
1.2.23.5
1.2.23.6
1.2.23.7
1.2.23.8
1.2.23.9
1.2.23.10
1.2.23.11
1.2.23.12
1.2.23.13
1.2.23.14
1.2.23.15
1.2.23.16
1.2.23.17
1.2.23.18
1.2.24
1.2.24.1
1.2.24.2
1.2.24.3
1.2.24.4
1.2.24.5
1.2.24.6
1.2.25
DN00211177
Issue 12B
IurUPSupport (User Plane support of Iur connection) . . . . . . . . . . . . . 320
PFL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
AMRToNonPreferredLayer (AMR to Non Preferred Layer) . . . . . . . . . 320
LaySelLowLoadPref (Layer Selection Low Load Preferred) . . . . . . . . 320
PREBTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
TechnologyInformation (Technology Information) . . . . . . . . . . . . . . . . 320
RNAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
DLmaxBitRatePerSF/DLmaxBitRateSF128 (Maximum DL bit rate with
spreading factor 128) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
PCrangeDL (Radio link downlink power control range) . . . . . . . . . . . . 321
SRBDelay (SRB delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
UlScrCodeMin (Uplink scrambling code minimum value) . . . . . . . . . . 322
LoadBasedAMRCodecMode (Usage of Load based AMR codec mode selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
RNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
CommonMCC (Common MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
CommonMNC (Common MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
ExtendedULDLactivationTmr (Extended Cell_FACH inactivity supervision
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
LCSfunctionality (LCS functionality). . . . . . . . . . . . . . . . . . . . . . . . . . . 325
ConnectionRetryCounter (OAM Connection Establishment Retry Counter)
325
SIB11_priority (Priority for SIB11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
SIB15_priority (Priority for SIB15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
SIB18_priority (Priority for SIB18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
SIB19Priority (Priority for SIB19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
SIB3_priority (Priority for SIB3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
PageRep1stInterv (Repetition interval of the first repeated connected
mode paging procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
RestrictionInterval (Restriction Interval) . . . . . . . . . . . . . . . . . . . . . . . . 328
RNCIPAddress (RNC IP-address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
RncOptions (RNC Options) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
ServingOMS (Serving OMS ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
ServingOMSAdminSetting (Serving OMS Admin Setting) . . . . . . . . . . 333
ServingOMSSwoRequest (Serving OMS Switchover Request) . . . . . 334
ULBLERConfInterval (Uplink measured BLER confidence interval) . . 335
RNFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
SignConnActivitySupervision (Activity supervision for NAS signaling connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
CapaSmartphoneEnabled (Capacity Increase for Smartphones Enabled)
336
HSDPA16KBPSReturnChannel (HSDPA 16 kbps UL DCH return channel
on/off switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
MOCNenabled (Multi-Operator Core Network enabled) . . . . . . . . . . . 337
PSOpThroUsage (Throughput based optimisation of the PS algorithm usage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
WireLessPriorityService (Usage of the Wireless Priority Service) . . . . 339
RNHSPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
Id:0900d805809d7397
15
WCDMA Radio Network Configuration Parameters
1.2.25.1
1.2.25.2
1.2.25.3
1.2.25.4
1.2.25.5
1.2.25.6
1.2.25.7
1.2.25.8
1.2.25.9
1.2.25.10
1.2.25.11
1.2.25.12
1.2.25.13
1.2.25.14
1.2.25.15
1.2.26
1.2.26.1
1.2.26.2
1.2.26.3
1.2.26.4
1.2.26.5
1.2.27
1.2.27.1
1.2.27.2
1.2.27.3
1.2.27.4
1.2.27.5
1.2.27.6
1.2.27.7
1.2.27.8
16
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
CPCNRT10msTTI/N10msCQIFeedbackCPC (CQI Feedback Cycle for
CPC NRT 10ms TTI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
CPCNRT2msTTI/N2msCQIFeedbackCPC (CQI Feedback Cycle for CPC
NRT 2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
CPCStreaming2msTTI/S2msCQIFeedbackCPC (CQI Feedback Cycle for
CPC Str 2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
CPCVoice2msTTI/V2msCQIFeedbackCPC (CQI Feedback Cycle for CPC
Voi 2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343
DCellVsMIMOPreference (Dual Cell versus MIMO preference) . . . . . . 343
HSDPAPeakRateLimitRABMax (HSDPA peak rate limitation to the RAB
maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343
HSPANBRValues (HSPA NBR values) . . . . . . . . . . . . . . . . . . . . . . . . 344
MACdflowthroughputRelThr (Low throughput threshold of the MAC-d flow)
344
MACdflowutilStrTtT (Low util time to trigger of MAC-d flow for streaming) .
345
HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346
MaxBitRateNRTMACDFlow (Maximum bit rate of NRT MAC-d flow) . . 347
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA). . . . 348
UPResAllocInCellDCHWait (Retry time for u-plane resource allocation in
Cell_DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
HSDPACellChangeRepetitionTime (Window for max repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
RNMOBI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell
selection). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
IBTSRabCombSupport (RAB Combinations Supported by FD-BTS) . . 352
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
RNPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
TrafVolThresholdDLHigh (Downlink traffic volume measurement high
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
TrafVolTimeToTriggerDL (Downlink traffic volume measurement time to
trigger). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
DCHUtilLowerDowngradeThrBitRate (Lower downgrade threshold) . . 356
CrQueuingTimeDL (Maximum downlink capacity request queuing time) . .
357
CrQueuingTimeUL (Maximum uplink capacity request queuing time) . 358
ActivationTimeOffset (Offset for activation time). . . . . . . . . . . . . . . . . . 358
TrafVolThresholdULHigh (Uplink traffic volume measurement high threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
TrafVolTimeToTriggerUL (Uplink traffic volume measurement time to trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.28
1.2.28.1
1.2.28.2
1.2.28.3
1.2.28.4
1.2.28.5
1.2.28.6
1.2.28.7
1.2.28.8
1.2.28.9
1.2.28.10
1.2.28.11
1.2.28.12
1.2.28.13
1.2.28.14
1.2.29
1.2.29.1
1.2.29.2
1.2.29.3
1.2.29.4
1.2.29.5
1.2.29.6
1.2.29.7
1.2.29.8
1.2.29.9
1.2.29.10
1.2.30
1.2.30.1
DN00211177
Issue 12B
RNRLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
AMRLCMaximumBufferUE/AMRLCMaximumBufferUE1k (AM RLC maximum buffer allocation for UE capability 1000) . . . . . . . . . . . . . . . . . . . 360
AMRLCMaximumBufferUE/AMRLCMaximumBufferUE1150 (AM RLC
maximum buffer allocation for UE capability 1150) . . . . . . . . . . . . . . . 361
AMRLCMaximumBufferUE/AMRLCMaximumBufferUE1250 (AM RLC
maximum buffer allocation for UE capability 1250) . . . . . . . . . . . . . . . 361
AMRLCOnDCHOfNRTPS/AMRLCOnDCHOfNRTPSMaxRST (AM RLC
MaxRST transmissions for PS NRT with DCH) . . . . . . . . . . . . . . . . . . 361
AMRLCOnEDCHOfNRTPS/AMRLCOnEDCHOfNRTPSMaxRST (AM
RLC maxRST transmissions for PS NRT with E-DCH) . . . . . . . . . . . . 362
AMRLCOnHSDSCHOfNRTPS/AMRLCOnHSDSCHOfNRTPSMaxRST
(AM RLC maxRST transmissions for PS NRT with HS-DSCH). . . . . . 362
AMRLCOnDCHOfNRTPS/AMRLCOnDCHOfNRTPSPollPDU (AM RLC
period Poll_PDU for PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . 362
AMRLCOnDCHOfNRTPS/AMRLCOnDCHOfNRTPSFilterReTX (AM RLC
retransmission filter for PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . 363
AMRLCOnHSDSCHOfNRTPS/AMRLCOnHSDSCHOfNRTPSFilterReTX
(AM RLC retransmission filter for PS NRT with HS-DSCH). . . . . . . . . 363
AMRLCOnHSDSCHOfStrPS/HSDSCHStrPSFilterReTX (AM RLC retransmission filter for PS stream with HS-DSCH) . . . . . . . . . . . . . . . . . . . . 364
AMRLCOnDCHOfStream/AMRLCOnDCHOfStreamFilterReTX (AM RLC
retransmission filter for PS streaming with DCH). . . . . . . . . . . . . . . . . 364
AMRLCOnDCHOfNRTPS/AMRLCOnDCHOfNRTPSPeriodMax (AM RLC
status period max for PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . 365
AMRLCOnEDCHOfNRTPS/AMRLCOnEDCHOfNRTPSPeriodMax (AM
RLC status period max for PS NRT with E-DCH) . . . . . . . . . . . . . . . . 365
AMRLCOnHSDSCHOfNRTPS/AMRLCOnHSDSCHOfNRTPSPeriodMax
(AM RLC status period max for PS NRT with HS-DSCH) . . . . . . . . . . 365
RNTRM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
ActivityFactorForAMRDCHTrafficBearers (Activity factor for AMR DCH
traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
ActivityFactorForCSDCHTrafficBearers (Activity factor for CS DCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
ActivityFactorForDCCHTrafficBearers (Activity factor for DCCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
ActivityFactorForFACHRACHTrafficBearers (Activity factor for FACH and
RACH traffic bearers). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
ActivityFactorForFACHRACHTrafficBearers/AfFACHCCDL (Activity factor
for FACH-C/C DL bearer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
ActivityFactorForHSPA (Activity factor for HSPA bearers) . . . . . . . . . 366
ActivityFactorForNRTDCHTrafficBearers (Activity factor for NRT DCH traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
ActivityFactorForPCHTrafficBearers (Activity factor for PCH traffic bearers)
367
ActivityFactorForRTPSTrafficBearers (Activity factor for RT PS traffic bearers). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
EchoRequestSending (Echo Request Sending) . . . . . . . . . . . . . . . . . 368
VBTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
ControllerIdPair/IHSPAadapterId (I-HSPA Adapter Identifier) . . . . . . . 368
Id:0900d805809d7397
17
WCDMA Radio Network Configuration Parameters
1.2.30.2
1.2.30.3
1.2.31
1.2.31.1
1.2.31.2
1.2.32
1.2.32.1
1.2.33
1.2.33.1
1.2.33.2
1.2.33.3
1.2.33.4
1.2.33.5
1.2.33.6
1.2.33.7
1.2.33.8
1.2.33.9
1.2.33.10
1.2.33.11
1.2.33.12
1.2.33.13
1.2.33.14
1.2.33.15
1.2.33.16
1.2.33.17
1.2.33.18
1.2.33.19
1.2.33.20
1.2.33.21
1.2.33.22
1.2.33.23
1.2.33.24
1.2.33.25
1.2.33.26
1.2.33.27
1.2.34
1.2.34.1
18
ControllerIdPair (Neighbouring FD-BTS Identifier and Its SRNC Identifier)
368
ControllerIdPair/ServingRNCId (Serving RNC Identifier) . . . . . . . . . . . 368
VCEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
WANE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
WANEName (WANE Name). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
WBTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
RRMULDCHActivityFactor (Average UL DCH data rates for the radio bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
BTSIPAddress (BTS O&M IP address). . . . . . . . . . . . . . . . . . . . . . . . . 371
BTSSupportForHSPACM (BTS Support For HSPA CM) . . . . . . . . . . . 371
COCOId (Connection Configuration Identifier) . . . . . . . . . . . . . . . . . . . 371
PWSMShutdownEndHour (Hour when the cell shutdown window ends) . .
372
PWSMShutdownBeginHour (Hour when the cell shutdown window starts)
373
HSDPACCEnabled (HSDPA Congestion Control activation) . . . . . . . . 373
HSDPAIurWeight (HSDPA Iur Weight) . . . . . . . . . . . . . . . . . . . . . . . . . 374
HSDPAOperIdWeightPair/HSDPAOperatorId (HSDPA Operator Identifier)
375
HSDPAOperIdWeightPair/HSDPAOperatorWeight (HSDPA Operator
Weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
HSDPAUserHysterisis (HSDPA User Hysterisis) . . . . . . . . . . . . . . . . . 377
HSDPAUserThreshold (HSDPA User Threshold). . . . . . . . . . . . . . . . . 377
ICREnabled (ICR Enabled). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
IPBasedRouteIdIub (IP Based Route Id Iub) . . . . . . . . . . . . . . . . . . . . 378
IPBasedRouteIdIub2 (IP Based Route Id Iub 2) . . . . . . . . . . . . . . . . . . 378
DelayThresholdMax2msTTI (Maximum Threshold for HSUPA congestion
delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
DelayThresholdMax (Maximum Threshold for HSUPA congestion handling
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
DelayThresholdMid2msTTI (Middle Threshold for HSUPA congestion delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
DelayThresholdMid (Middle Threshold value for HSUPA congestion delay)
380
PWSMShutdownEndMin (Minute when the cell shutdown window ends) .
381
PWSMShutdownBeginMin (Minute when the cell shutdown window starts)
381
NESWVersion (NE-SW-Version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
NEType (NE-type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
RFSharingState (RF Sharing State) . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
SatelliteIubUsage (Satellite Iub Usage) . . . . . . . . . . . . . . . . . . . . . . . . 382
SchedulingPeriod (Scheduling period) . . . . . . . . . . . . . . . . . . . . . . . . . 383
TQMId (TQM object identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
WCEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384
AllowedPreambleSignatures (Allowed preamble signatures) . . . . . . . . 384
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.34.2
1.2.34.3
1.2.34.4
1.2.34.5
1.2.34.6
1.2.34.7
1.2.34.8
1.2.34.9
1.2.34.10
1.2.34.11
1.2.34.12
1.2.34.13
1.2.34.14
1.2.34.15
1.2.34.16
1.2.34.17
1.2.34.18
1.2.34.19
1.2.34.20
1.2.34.21
1.2.34.22
1.2.34.23
1.2.34.24
1.2.34.25
1.2.34.26
1.2.34.27
1.2.34.28
1.2.34.29
1.2.34.30
1.2.34.31
1.2.34.32
1.2.34.33
1.2.34.34
1.2.34.35
1.2.34.36
1.2.34.37
DN00211177
Issue 12B
BlindHOEcNoThrTarget (Blind HO EcNo threshold for target cell) . . . 384
KforCTCH (CBS frame offset (K)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
CellRange (Cell range) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
CPCEnabled (CPC enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387
CTCHCapaHighPri (CTCH capacity for High Priority CBS messages) 387
DCellHSDPAEnabled (DC HSDPA Enabled) . . . . . . . . . . . . . . . . . . . 388
OCULNRTDCHGrantedMinAllocT (DCH time limit for UL NRT DCH overload in E-DCH cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
TrafVolThresholdDLLow (Downlink traffic volume measurement low
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
EVAMInUse (EVAM in use) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
PtxFDPCHMax (F-DPCH maximum transmission power) . . . . . . . . . . 391
PtxFDPCHMin (F-DPCH minimum transmission power) . . . . . . . . . . . 391
Tcell (Frame timing offset of a cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
WCELGlobalCNid (Global CN Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
HSDPAenabled (HSDPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for speech services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
RTWithHSDPAFmciIdentifier (HSDPA FMCI identifier for speech services)
396
RTWithHSDPAFmcsIdentifier (HSDPA FMCS identifier for speech services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for speech services)
398
HSPAQoSEnabled (HSPA QoS enabled) . . . . . . . . . . . . . . . . . . . . . . 400
ICRCapability (ICR Capability). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401
IncomingLTEISHO (Incoming ISHO from LTE) . . . . . . . . . . . . . . . . . . 402
LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402
UsersPerHSSCCHCode (Max nbr of conv users per reserved HS-SCCH
code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
PrxMaxOrigTargetBTS (Max target received wide band original power for
BTS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
PrxMaxTargetBTS (Maximum target received wide band power for BTS)
404
MBLBRABSetupMultiRAB (MBLB in RAB Setup for Multi RAB) . . . . . 404
PtxTargetPSMin (Min DCH PS target for dynamic HSDPA pwr allocation)
405
PrxTargetPSMin (Min PS target in HSPA-DCH interference sharing) . 405
MultiplePLMNListIncluded (Multiple PLMN List Included) . . . . . . . . . . 406
NbrOfSCCPCHs (Number of SCCPCHs) . . . . . . . . . . . . . . . . . . . . . . 406
CPICHtoRefRABoffset (Offset of the P-CPICH and reference service powers). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
NforCTCH (Period of CTCH allocation (N)) . . . . . . . . . . . . . . . . . . . . . 408
EvamNumPhaseOffset (Phase offset amount) . . . . . . . . . . . . . . . . . . 409
PowerOffsetLastPreamblePRACHmessage (Power offset last preamble
and PRACH message). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
PowerRampStepPRACHpreamble (Power ramp step on PRACH preamble) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
RACHCapacity (RACH Capacity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
Id:0900d805809d7397
19
WCDMA Radio Network Configuration Parameters
1.2.34.38
1.2.34.39
1.2.34.40
1.2.34.41
1.2.34.42
1.2.34.43
1.2.34.44
1.2.34.45
1.2.34.46
1.2.34.47
1.2.34.48
1.2.34.49
1.2.34.50
1.2.34.51
1.2.34.52
1.2.34.53
1.2.34.54
1.2.34.55
1.2.35
1.2.35.1
1.2.35.2
1.2.35.3
1.2.35.4
1.2.36
1.2.36.1
1.2.36.2
1.3
1.3.1
1.3.1.1
1.3.1.2
1.3.1.3
1.3.1.4
1.3.2
1.3.2.1
1.3.2.2
1.3.2.3
1.3.2.4
1.3.2.5
1.3.2.6
1.3.2.7
1.3.2.8
20
RACH_tx_Max (RACH maximum number of preamble cycles) . . . . . . 409
RNARGroupId (Radio Network Access Regulation Function Group Id) 410
RsrvdSignaturesOffset (Reserved E-RGCH and E-HICH signatures per
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
CSGroupId (Restriction Group Id for Circuit Switched Acces) . . . . . . . 410
PSGroupId (Restriction Group Id for Packet Switched Acces) . . . . . . . 410
RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
SectorID (Sector Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
SACB (Service Area Code for SAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
EvamTSweep (Sweep time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
T315 (T315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
HSFACHActivityThr (Threshold of the HS-DSCH MAC-d flow of PS RB on
HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
HSFACHActTimeToTrigger (Time to trigger for activity measurement on
HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
HSFACHRLCTimeToTrigger (Time to trigger for RLC measurement on
HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
PtxPrimaryCPICH (Transmission power of the primary CPICH channel) . .
414
URAId (URA identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
UTRAN_DRX_length (UTRAN DRX cycle length) . . . . . . . . . . . . . . . . 415
WCelState (WCDMA Cell Operational State) . . . . . . . . . . . . . . . . . . . . 416
LHOWinSizeONCapaReqRejRate (Window size for NRT load measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
WLCSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
WLCSEUtranCellId/WLCSECId (Cell Identifier) . . . . . . . . . . . . . . . . . . 417
WLCSEUtranCellId/WLCSEMNC (Mobile Network Code) . . . . . . . . . . 417
WLCSEUtranCellId/WLCSEMNCLength (Mobile Network Code Length) .
418
WLCSEUtranCellId/WLCSERncId (RNC Identifier) . . . . . . . . . . . . . . . 418
WRAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418
EbNoDCHRateGain (Data rate gain in the Eb/N0 definition) . . . . . . . . 418
SIRDPCCHInitialDCH (Initial SIR target for UL DPCCH with DPDCH) 420
Removed Parameters in RNC RN7.0 . . . . . . . . . . . . . . . . . . . . . . . . . . 422
CBCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
CBCPLMNId (CBC PLMN id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
CBCPLMNId/MCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . 422
CBCPLMNId/MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . 422
CBCPLMNId/MNCLength (Mobile Network Code Length) . . . . . . . . . . 422
IUCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
CNDRXLength (CN domain specific DRX cycle length) . . . . . . . . . . . . 422
GlobalCNId/CNId (Core Network Identity) . . . . . . . . . . . . . . . . . . . . . . 422
GlobalCNId (GlobalCNId) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
Iufailure (Iu interface failure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423
IuBarringRecoveryTimer (Iu service barring recovery timer) . . . . . . . . 423
GlobalCNId/MCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . 423
GlobalCNId/MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . 423
GlobalCNId/MNCLength (Mobile Network Code Length) . . . . . . . . . . . 423
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.3.3
1.3.3.1
1.3.3.2
1.3.3.3
1.3.3.4
1.3.3.5
1.3.3.6
1.3.3.7
1.3.3.8
1.3.4
1.3.4.1
DN00211177
Issue 12B
1.3.5
1.3.6
1.3.6.1
1.3.6.2
1.3.6.3
1.3.6.4
1.3.7
1.3.8
1.3.9
1.3.9.1
1.3.10
1.3.11
1.3.11.1
1.3.11.2
1.4
1.4.1
1.4.2
1.4.3
1.4.4
1.4.5
1.4.6
IUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423
CNDRXLength (CN domain specific DRX cycle length) . . . . . . . . . . . 423
GlobalCNId/CNId (Core Network Identity) . . . . . . . . . . . . . . . . . . . . . . 423
GlobalCNId (GlobalCNId) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423
Iufailure (Iu interface failure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423
IuBarringRecoveryTimer (Iu service barring recovery timer) . . . . . . . . 423
GlobalCNId/MCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . 423
GlobalCNId/MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . 424
GlobalCNId/MNCLength (Mobile Network Code Length) . . . . . . . . . . 424
IUR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
maxHSDPAFPSizeForATMIur (Maximum HS-DSCH FP size for ATM Iur)
424
RNAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
RNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
SIB12_priority (Priority for SIB12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
SIB4_priority (Priority for SIB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
SIB6_priority (Priority for SIB6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
SIB7_priority (Priority for SIB7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
RNHSPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
RNPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
RNTRM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
SignallingToDSCP (Signalling to DSCP mapping) . . . . . . . . . . . . . . . 425
VCEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
WCEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
WCELGlobalCNid/WCELCSCNId (CS Core Network Identity) . . . . . . 425
WCELGlobalCNid/WCELPSCNId (PS Core Network Identity) . . . . . . 425
Moved Parameters in RNC RN7.0. . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
Parameters moved from IUCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
Parameters moved from IUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
Parameters moved from RNAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426
Parameters moved from RNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426
Parameters moved from RNHSPA . . . . . . . . . . . . . . . . . . . . . . . . . . . 426
Parameters moved from RNPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
2
2.1
2.2
Introduction to RNC radio network configuration parameters . . . . . . . 429
Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
How to read parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
ADJD Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
ADJDChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 431
ADJDId (Identifier of additional intra-frequency adjacency). . . . . . . . . 432
AdjdCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433
AdjdCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . 434
AdjdDERR (Disable Effect on Reporting Range). . . . . . . . . . . . . . . . . 435
AdjdHSDPAHopsId (HSDPA HOPS identifier) . . . . . . . . . . . . . . . . . . 436
AdjdLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
AdjdMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438
AdjdMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
Id:0900d805809d7397
21
WCDMA Radio Network Configuration Parameters
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
3.18
AdjdMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 440
AdjdNRTHopsId (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 441
AdjdRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442
AdjdRNCId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
AdjdRTHopsId (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 444
AdjdRTWithHSDPAHopsId (HSDPA HOPS identifier for speech services)
445
AdjdSRBHopsId (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 446
AdjdScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . 448
AdjdTxDiv (Tx Diversity Indicator). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
ADJG Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
ADJGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 450
ADJGId (Inter-system adjacency identifier) . . . . . . . . . . . . . . . . . . . . . 451
ADJGType (Inter-system Neighbour Cell Type) . . . . . . . . . . . . . . . . . . 452
AdjgBCC (Base Station Colour Code) . . . . . . . . . . . . . . . . . . . . . . . . . 453
AdjgBCCH (BCCH ARFCN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454
AdjgBandIndicator (Band Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . 455
AdjgCI (Cell Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456
AdjgLAC (Location Area Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457
AdjgMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
AdjgMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
AdjgMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 460
AdjgNCC (Network Colour Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
AdjgSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . 462
AdjgTxPwrMaxRACH (Maximum UE TX Power on RACH) . . . . . . . . . 465
AdjgTxPwrMaxTCH (Maximum UE TX Power on TCH) . . . . . . . . . . . . 466
NrtHopgIdentifier (NRT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 468
RtHopgIdentifier (RT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 469
5
5.1
5.2
5.3
5.4
5.5
ADJI Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
ADJIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
ADJIId (Inter-frequency adjacency identifier) . . . . . . . . . . . . . . . . . . . . 472
AdjiCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
AdjiCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . . 474
AdjiComLoadMeasDRNCCellNCHO (NCHO activity of common load measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
AdjiEcNoOffsetNCHO (CPICH EcNo offset for the non-critical HO procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 476
AdjiHandlingBlockedCellSLHO (Handling of blocked IF neighbour cell in
SLHO procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478
AdjiLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479
AdjiMCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480
AdjiMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481
AdjiMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . 482
AdjiNCHOHSPASupport (ADJI HSPA Cell for Non Critical Handover) 483
AdjiRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
AdjiRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
AdjiSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . . 486
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
22
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
DN00211177
Issue 12B
5.16
5.17
5.18
5.19
5.20
5.21
5.22
5.23
AdjiScrCode (Primary Scrambling Code). . . . . . . . . . . . . . . . . . . . . . . 490
AdjiTxDiv (Tx Diversity Indicator). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491
AdjiTxPwrDPCH (Maximum UE TX Power on DPCH). . . . . . . . . . . . . 492
AdjiTxPwrRACH (Maximum UE TX Power on RACH). . . . . . . . . . . . . 493
AdjiUARFCN (UTRA Absolute Radio Frequency Channel Number) . . 494
BlindHOTargetCell (Blind HO target cell). . . . . . . . . . . . . . . . . . . . . . . 497
NrtHopiIdentifier (NRT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 498
RtHopiIdentifier (RT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 499
6
6.1
6.2
6.3
6.4
6.5
ADJL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501
ADJLChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 501
ADJLId (Identifier of inter- system adjacency to LTE). . . . . . . . . . . . . 502
AdjLEARFCN (E-UTRA Absolute Radio Frequency Channel Number) 503
AdjLMeasBw (Measurement Bandwidth). . . . . . . . . . . . . . . . . . . . . . . 504
HopLIdentifier (HOPL Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
7.12
7.13
7.14
7.15
7.16
7.17
7.18
7.19
7.20
7.21
ADJS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
ADJSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 507
ADJSId (Intra-frequency adjacency identifier) . . . . . . . . . . . . . . . . . . . 508
AdjsCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
AdjsCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . 510
AdjsDERR (Disable Effect on Reporting Range) . . . . . . . . . . . . . . . . . 511
AdjsEcNoOffset (CPICH Ec/No Offset) . . . . . . . . . . . . . . . . . . . . . . . . 512
AdjsLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
AdjsMCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
AdjsMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
AdjsMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 516
AdjsRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
AdjsRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518
AdjsSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . 519
AdjsScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . 522
AdjsTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523
AdjsTxPwrRACH (Maximum UE TX Power on RACH) . . . . . . . . . . . . 524
HSDPAHopsIdentifier (HSDPA HOPS identifier). . . . . . . . . . . . . . . . . 525
NrtHopsIdentifier (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 526
RTWithHSDPAHopsIdentifier (HSDPA HOPS identifier for speechservices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527
RtHopsIdentifier (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 528
SRBHopsIdentifier (SRB HOPS Identifier). . . . . . . . . . . . . . . . . . . . . . 529
8
8.1
8.2
8.3
8.4
8.5
8.6
8.7
CBCI Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531
CBCIChangeOrigin (CBCI Change Origin) . . . . . . . . . . . . . . . . . . . . . 531
CBCIId (CBCI Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532
CBCIPaddrType (Type of CBC IP address). . . . . . . . . . . . . . . . . . . . . 533
CBCIPaddress (IP address of the CBC) . . . . . . . . . . . . . . . . . . . . . . . 534
ETWSsupportEnabled (ETWS Support Enabled) . . . . . . . . . . . . . . . . 535
ICSUforCBC (ICSU for CBC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536
IUOIdentifier (IUO Object Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . 537
9
CMOB Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538
Id:0900d805809d7397
23
WCDMA Radio Network Configuration Parameters
9.1
9.2
9.3
9.4
9.5
9.6
9.7
ACBarredListSystem (Access Class Barred List given by System) . . . 538
CMOBChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 540
CMOBId (Congestion Management Group Identifier). . . . . . . . . . . . . . 541
CellAccessRestriction (Cell Access Restriction) . . . . . . . . . . . . . . . . . . 542
RestrictionGroupName (Restriction group name) . . . . . . . . . . . . . . . . . 543
RestrictionGroupType (Restriction group type). . . . . . . . . . . . . . . . . . . 544
TrafficRestriction (Traffic Restriction) . . . . . . . . . . . . . . . . . . . . . . . . . . 545
10
10.1
10.2
10.3
10.4
COCO Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547
AAL2LossRatio (AAL2 CPS-SDU loss ratio) . . . . . . . . . . . . . . . . . . . . 547
AAL2Multiplexing (BTS AAL2 multiplexing) . . . . . . . . . . . . . . . . . . . . . 548
AAL2MuxDelay (AAL2 CPS-SDU multiplexing delay) . . . . . . . . . . . . . 549
AAL2QueueHSDPAWithFC (AAL2 Queue Length for HSDPA With Flow
Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
AAL2QueueHSDPAWithoutFC (AAL2 Queue Length for HSDPA Without
Flow Control). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
AAL2QueueHSUPA (AAL2 Queue Length for HSUPA) . . . . . . . . . . . . 552
AAL2QueueNRTDCHWithFC (AAL2 Queue Length for NRT DCH With
Flow Control). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553
AAL2QueueNRTDCHWithoutFC (AAL2 Queue Length for NRT DCH Without Flow Control). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554
AAL2QueueRTDCH (AAL2 Queue Length for RT DCH) . . . . . . . . . . . 555
AAL2SignLinkTP (AAL2 signalling link configuration). . . . . . . . . . . . . . 556
AAL2SigCDVT01Egr (AAL2 signalling link VCLtp CDVT egress) . . . . 557
AAL2SigCDVT01Ing (AAL2 signalling link VCLtp CDVT ingress) . . . . 558
AAL2SigEarlyPacketDiscard (AAL2 SL Early Packet Discard). . . . . . . 559
AAL2SigEgressMDCR (AAL2 SL Egress Minimum Desired Cell Rate) 560
AAL2SigEgressUBRShare (AAL2 SL Egress UBR Share Weight Of Excessive Bandwidth). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
AAL2SigIngressMDCR (AAL2 SL Ingress Minimum Desired Cell Rate) . .
562
AAL2SigIngressUBRShare (AAL2 SL Ingress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563
AAL2SigPCR01Egr (AAL2 signalling link VCLtp PCR egress). . . . . . . 564
AAL2SigPCR01Ing (AAL2 signalling link VCLtp PCR ingress). . . . . . . 565
AAL2SigPartialPacketDiscard (AAL2 SL Partial Packet Discard). . . . . 566
AAL2SigServiceCategory (AAL2 SL Service Category) . . . . . . . . . . . . 567
AAL2SigTPAdmState (AAL2 signalling link VCLtp effective administrative
state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568
AAL2SignLinkATMIfId (AAL2 signalling link ATM interface Identifier) . 569
AAL2SignLinkTPId (AAL2 signalling link termination point Identifier ) . 570
AAL2SignLinkVCI (AAL2 signalling link Virtual Channel Identifier) . . . 571
AAL2SignLinkVPI (AAL2 signalling link Virtual Path Identifier). . . . . . . 572
AAL2TP (AAL2 user plane link configuration). . . . . . . . . . . . . . . . . . . . 573
AAL2FallbAttribute (AAL2 Fallback attribute) . . . . . . . . . . . . . . . . . . . . 575
AAL2PathId (AAL type 2 path identifier) . . . . . . . . . . . . . . . . . . . . . . . . 576
AAL2PathType (AAL2 Path Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577
AAL2SignLinkATMIfId (AAL2 signalling link ATM interface Identifier) . 579
AAL2SignLinkVCI (AAL2 signalling link Virtual Channel Identifier) . . . 580
10.5
10.6
10.7
10.8
10.9
10.10
10.11
10.12
10.13
10.14
10.15
10.16
10.17
10.18
10.19
10.20
10.21
10.22
10.23
10.24
10.25
10.26
10.27
10.28
10.29
10.30
10.31
10.32
24
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
10.33
10.34
10.35
10.36
10.37
10.38
10.39
10.40
10.41
10.42
10.43
10.44
10.45
10.46
10.47
10.48
10.49
10.50
10.51
10.52
10.53
10.54
10.55
10.56
10.57
10.58
10.59
10.60
10.61
10.62
10.63
10.64
10.65
10.66
10.67
10.68
10.69
10.70
10.71
10.72
10.73
10.74
DN00211177
Issue 12B
AAL2SignLinkVPI (AAL2 sign link reference Virtual Path Identifier) . . 581
AAL2UPATMIfId (AAL2 user plane ATM interface Identifier) . . . . . . . 582
AAL2UPCDVT01Egr (AAL2 user plane link VCLtp CDVT egress) . . . 583
AAL2UPCDVT01Ing (AAL2 user plane link VCLtp CDVT ingress) . . . 584
AAL2UPEgressMDCR (AAL2 UP Egress Minimum Desired Cell Rate) 585
AAL2UPEgressUBRShare (AAL2 UP Egress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586
AAL2UPIngressMDCR (AAL2 UP Ingress Minimum Desired Cell Rate). .
587
AAL2UPIngressUBRShare (AAL2 UP Ingress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588
AAL2UPPCR01Egr (AAL2 user plane link VCLtp PCR egress) . . . . . 589
AAL2UPPCR01Ing (AAL2 user plane link VCLtp PCR ingress) . . . . . 590
AAL2UPServiceCategory (AAL2 UP Service Category) . . . . . . . . . . . 591
AAL2UPTPAdmState (AAL2 user plane link VCLtp effective administrative
state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592
AAL2UPUsage (AAL2 User Plane VCC Usage) . . . . . . . . . . . . . . . . . 593
AAL2UPVCI (AAL2 user plane Virtual Channel Identifier). . . . . . . . . . 595
AAL2UPVPI (AAL2 user plane Virtual Path Identifier) . . . . . . . . . . . . . 596
ANI (Adjacent AAL type 2 node identifier) . . . . . . . . . . . . . . . . . . . . . . 597
COCOA2EA (AAL type 2 end point address for Iub) . . . . . . . . . . . . . . 598
DATree (Iub Digit analysis tree). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
Route (Route identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 601
VCCInBundle (VCC In Bundle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 602
WAMId (WAM identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 603
ATMEPProfileId (ATM End Point Profile Id). . . . . . . . . . . . . . . . . . . . . 604
ATMInterface (ATM interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605
ATMIfAdmState (ATM interface administrative state) . . . . . . . . . . . . . 606
ATMIfMaxBandwidthEgr (ATM interface maximum bandwidth egress) 607
ATMIfMaxBandwidthIng (ATM interface maximum bandwidth ingress) 608
ATMIfMaxVCIBits (ATM interface maximum VCI bits). . . . . . . . . . . . . 609
ATMIfMaxVPIBits (ATM interface maximum VPI bits) . . . . . . . . . . . . . 609
ATMIfPhysicalTTPId (ATM interface physical TTP). . . . . . . . . . . . . . . 610
ATMInterfaceID (ATM interface identifier) . . . . . . . . . . . . . . . . . . . . . . 611
ATMInterfaceType (ATM interface type) . . . . . . . . . . . . . . . . . . . . . . . 612
CNBAPTP (C-NBAP signalling link configuration) . . . . . . . . . . . . . . . . 613
CNBAPCDVT01Egr (C-NBAP VCLtp CDVT egress). . . . . . . . . . . . . . 614
CNBAPCDVT01Ing (C-NBAP VCLtp CDVT ingress) . . . . . . . . . . . . . 615
CNBAPEarlyPacketDiscard (C-NBAP Early Packet Discard) . . . . . . . 616
CNBAPEgressMDCR (C-NBAP Egress Minimum Desired Cell Rate). 617
CNBAPEgressUBRShare (C-NBAP Egress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 618
CNBAPICSUIndex (ICSU index for C-NBAP link) . . . . . . . . . . . . . . . . 619
CNBAPIngressMDCR (C-NBAP Ingress Minimum Desired Cell Rate) 620
CNBAPIngressUBRShare (C-NBAP Ingress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621
CNBAPOpState (Operational Status of C-NBAP link) . . . . . . . . . . . . . 622
CNBAPPCR01Egr (C-NBAP VCLtp PCR egress) . . . . . . . . . . . . . . . . 623
Id:0900d805809d7397
25
WCDMA Radio Network Configuration Parameters
10.75
10.76
10.77
10.78
10.79
10.80
10.81
10.82
10.83
10.84
10.85
10.86
10.87
10.88
10.89
10.90
10.91
10.92
10.93
10.94
10.95
10.96
10.97
10.98
10.99
10.100
10.101
10.102
10.103
10.104
10.105
10.106
10.107
10.108
10.109
10.110
10.111
10.112
10.113
10.114
10.115
10.116
10.117
10.118
26
CNBAPPCR01Ing (C-NBAP VCLtp PCR ingress) . . . . . . . . . . . . . . . . 624
CNBAPPartialPacketDiscard (C-NBAP Partial Packet Discard). . . . . . 625
CNBAPServiceCategory (C-NBAP Service Category) . . . . . . . . . . . . . 626
CNBAPTPATMIfId (C-NBAP ATM interface identifier) . . . . . . . . . . . . . 627
CNBAPTPAdmState (C-NBAP VCLtp effective administrative state) . . 628
CNBAPVCI (C-NBAP Virtual Channel Identifier) . . . . . . . . . . . . . . . . . 629
CNBAPVPI (C-NBAP Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . 630
COCOChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 631
COCOId (Connection Configuration Identifier) . . . . . . . . . . . . . . . . . . . 632
CalculateCDVT (Calculate CDVT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633
CreateATMTP (Create ATM termination points) . . . . . . . . . . . . . . . . . . 634
DNBAPTP (D-NBAP signalling link configuration) . . . . . . . . . . . . . . . . 635
CControlPortID (Communication Control Port) . . . . . . . . . . . . . . . . . . . 636
DNBAPATMIfId (D-NBAP ATM interface identifier) . . . . . . . . . . . . . . . 637
DNBAPCDVT01Egr (D-NBAP VCLtp CDVT egress) . . . . . . . . . . . . . . 638
DNBAPCDVT01Ing (D-NBAP VCLtp CDVT ingress) . . . . . . . . . . . . . . 639
DNBAPEarlyPacketDiscard (D-NBAP Early Packet Discard) . . . . . . . . 640
DNBAPEgressMDCR (D-NBAP Egress Minimum Desired Cell Rate) . 641
DNBAPEgressUBRShare (D-NBAP Egress UBR Share Weight Of Excessive Bandwidth). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642
DNBAPICSUIndex (ICSU index for D-NBAP link) . . . . . . . . . . . . . . . . 643
DNBAPIngressMDCR (D-NBAP Ingress Minimum Desired Cell Rate) 644
DNBAPIngressUBRShare (D-NBAP Ingress UBR Share Weight Of Excessive Bandwidth). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645
DNBAPOpState (Operational Status of D-NBAP link) . . . . . . . . . . . . . 646
DNBAPPCR01Egr (D-NBAP VCLtp PCR egress) . . . . . . . . . . . . . . . . 647
DNBAPPCR01Ing (D-NBAP VCLtp PCR ingress) . . . . . . . . . . . . . . . . 648
DNBAPPartialPacketDiscard (DNBAP Partial Packet Discard) . . . . . . 649
DNBAPServiceCategory (D-NBAP Service Category) . . . . . . . . . . . . . 650
DNBAPTPAdmState (D-NBAP VCLtp effective administrative state) . . 651
DNBAPVCI (D-NBAP Virtual Channel Identifier) . . . . . . . . . . . . . . . . . 652
DNBAPVPI (D-NBAP Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . 653
DynNRTDCHSchedPathSwitch (Dynamic NRT DCH Scheduling With Path
Selection Switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654
GenerateAAL2Num (Generate AAL2 user plane link numbers) . . . . . . 655
InternalHSDPAFCMethodBTS (Internal HSDPA Flow Control Method for
BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657
VCCBundleParams (VCC Bundle parameters) . . . . . . . . . . . . . . . . . . 658
VCCBundleEBS (VCC Bundle Excess Bandwidth Share) . . . . . . . . . . 659
VCCBundleId (VCC Bundle identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 660
VCCBundlePCR (VCC Bundle Peak Cell Rate) . . . . . . . . . . . . . . . . . . 661
VPLTP (Virtual Path Link termination point) . . . . . . . . . . . . . . . . . . . . . 662
COCOVPI (Virtual Path Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663
VPLTPATMIfId (VPLtp ATM interface identifier) . . . . . . . . . . . . . . . . . . 664
VPLTPAdmState (VPLtp effective administrative state) . . . . . . . . . . . . 665
VPLTPCDVT01Egr (VPLtp CDVT egress) . . . . . . . . . . . . . . . . . . . . . . 665
VPLTPEgressMDCR (VPLTP Egress Minimum Desired Cell Rate) . . . 666
VPLTPPCR01Egr (VPLtp PCR egress) . . . . . . . . . . . . . . . . . . . . . . . . 667
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
10.119
10.120
10.121
VPLTPServiceCategory (VPLtp Service Category) . . . . . . . . . . . . . . . 668
VPLTPTrafficShaping (VPLtp VP level traffic shaping) . . . . . . . . . . . . 669
WBTSId (WBTS Identification). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 670
11
11.1
11.2
11.3
COSITE Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 672
COSITEChangeOrigin (COSITE Change origin) . . . . . . . . . . . . . . . . . 672
COSITEId (COSITE Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673
SharingState (Sharing State) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674
12
12.1
12.2
12.3
12.4
12.5
12.6
12.7
12.8
12.9
12.10
COSRNC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 676
AdditionalStateInfo (Additional State Information) . . . . . . . . . . . . . . . . 676
AdminStateInfo (Admin State Info) . . . . . . . . . . . . . . . . . . . . . . . . . . . 677
AdministrativeState (Administrative State). . . . . . . . . . . . . . . . . . . . . . 678
AvailabilityStatus (Availability Status) . . . . . . . . . . . . . . . . . . . . . . . . . 679
COSRNCChangeOrigin (COSRNC Change origin). . . . . . . . . . . . . . . 681
COSRNCId (COSRNC Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682
ClusterIfState (Cluster Interface State) . . . . . . . . . . . . . . . . . . . . . . . . 683
OperationalState (Operational State ) . . . . . . . . . . . . . . . . . . . . . . . . . 684
PeerRNCIPAddress (Peer RNC IP Address). . . . . . . . . . . . . . . . . . . . 685
RNCOMConnState (RNC-RNC O&M Connection State) . . . . . . . . . . 686
13
13.1
FMCG Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 688
AMRDirReCell (Usage of Directed Retry of AMR call Inter-system Handov)
688
DLDPCHTxPwrClOffset (DL DPCH Transmission Power Cancellation Offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 689
FMCGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 690
FMCGId (FMCG identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691
GSMcauseCPICHEcNo (GSM HO caused by CPICH Ec/No). . . . . . . 692
GSMcauseCPICHrscp (GSM HO caused by CPICH RSCP). . . . . . . . 694
GSMcauseTxPwrDL (GSM HO caused by DL DPCH TX Power) . . . . 695
GSMcauseTxPwrUL (GSM HO caused by UE TX Power) . . . . . . . . . 697
GSMcauseUplinkQuality (GSM HO caused by UL DCH Quality) . . . . 699
GsmDLTxPwrThrAMR (DL DPCH TX Power Threshold for AMR) . . . 700
GsmDLTxPwrThrCS (DL DPCH TX Power Threshold for CS) . . . . . . 701
GsmDLTxPwrThrNrtPS (DL DPCH TX Power Threshold for NRT PS) 702
GsmDLTxPwrThrRtPS (DL DPCH TX Power Threshold for RT PS) . . 703
GsmMaxMeasPeriod (Maximum Measurement Period) . . . . . . . . . . . 705
GsmMeasAveWindow (Measurement Averaging Window) . . . . . . . . . 706
GsmMeasRepInterval (Measurement Reporting Interval) . . . . . . . . . . 707
GsmMinHoInterval (Minimum Interval Between HOs) . . . . . . . . . . . . . 708
GsmMinMeasInterval (Minimum Measurement Interval) . . . . . . . . . . . 708
GsmMinSLHOInterval (Minimum interval between repetitive inter-RAT
SLHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710
GsmNcellSearchPeriod (GSM Neighbour Cell Search Period) . . . . . . 711
GsmUETxPwrFilterCoeff (UE TX Power Filter Coefficient) . . . . . . . . . 712
GsmUETxPwrThrAMR (UE TX Power Threshold for AMR) . . . . . . . . 713
GsmUETxPwrThrCS (UE TX Power Threshold for CS) . . . . . . . . . . . 714
GsmUETxPwrThrNrtPS (UE TX Power Threshold for NRT PS) . . . . . 716
13.2
13.3
13.4
13.5
13.6
13.7
13.8
13.9
13.10
13.11
13.12
13.13
13.14
13.15
13.16
13.17
13.18
13.19
13.20
13.21
13.22
13.23
13.24
DN00211177
Issue 12B
Id:0900d805809d7397
27
WCDMA Radio Network Configuration Parameters
13.25
13.26
13.27
13.28
13.29
13.30
13.31
13.32
14
14.1
14.2
14.3
14.4
14.5
14.6
14.7
14.8
14.9
14.10
14.11
14.19
14.20
14.21
14.22
14.23
14.24
14.25
14.26
14.27
FMCI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727
FMCIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 727
FMCIId (FMCI identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 728
IFHOcauseCPICHEcNo (IFHO caused by CPICH Ec/No) . . . . . . . . . . 729
IFHOcauseCPICHrscp (IFHO caused by CPICH RSCP) . . . . . . . . . . . 730
IFHOcauseTxPwrDL (IFHO caused by DL DPCH TX Power) . . . . . . . 732
IFHOcauseTxPwrUL (IFHO caused by UE TX Power). . . . . . . . . . . . . 734
IFHOcauseUplinkQuality (IFHO caused by UL DCH Quality). . . . . . . . 736
IMSIbasedIFHO (IMSI Based IFHO). . . . . . . . . . . . . . . . . . . . . . . . . . . 737
InterFreqDLTxPwrThrAMR (DL DPCH TX Power Threshold for AMR) 738
InterFreqDLTxPwrThrCS (DL DPCH TX Power Threshold for CS) . . . 739
InterFreqDLTxPwrThrNrtPS (DL DPCH TX Power Threshold for NRT PS)
740
InterFreqDLTxPwrThrRtPS (DL DPCH TX Power Threshold for RT PS) . .
741
InterFreqMaxMeasPeriod (Maximum Measurement Period) . . . . . . . . 743
InterFreqMeasAveWindow (Measurement Averaging Window) . . . . . . 744
InterFreqMeasRepInterval (Measurement Reporting Interval) . . . . . . . 745
InterFreqMinHoInterval (Minimum Interval Between HOs) . . . . . . . . . . 746
InterFreqMinMeasInterval (Minimum Measurement Interval) . . . . . . . . 747
InterFreqMinSLHOInterval (Minimum interval between repetitive IF
SLHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748
InterFreqNcellSearchPeriod (Neighbour Cell Search Period). . . . . . . . 749
InterFreqUETxPwrFilterCoeff (UE TX Power Filter Coefficient) . . . . . . 750
InterFreqUETxPwrThrAMR (UE TX Power Threshold for AMR) . . . . . 751
InterFreqUETxPwrThrCS (UE TX Power Threshold for CS) . . . . . . . . 753
InterFreqUETxPwrThrNrtPS (UE TX Power Threshold for NRT PS) . . 754
InterFreqUETxPwrThrRtPS (UE TX Power Threshold for RT PS) . . . . 755
InterFreqUETxPwrTimeHyst (UE TX Power Time Hysteresis) . . . . . . . 756
MBLBMobilityOffset (MBLB due to Mobility EcNo Offset). . . . . . . . . . . 757
MBLBMobilityRABComb (MBLB due to Mobility RAB Combinations) . 759
15
15.1
15.2
15.3
15.4
FMCS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 760
ActiveSetWeightingCoefficient (Active Set Weighting Coefficient) . . . . 760
AdditionReportingInterval (Addition Reporting Interval) . . . . . . . . . . . . 761
AdditionTime (Addition Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 762
AdditionWindow (Addition Window) . . . . . . . . . . . . . . . . . . . . . . . . . . . 764
14.12
14.13
14.14
14.15
14.16
14.17
14.18
28
GsmUETxPwrThrRtPS (UE TX Power Threshold for RT PS) . . . . . . . 717
GsmUETxPwrTimeHyst (UE TX Power Time Hysteresis) . . . . . . . . . . 718
IMSIbasedGsmHo (IMSI Based GSM HO) . . . . . . . . . . . . . . . . . . . . . . 720
ISHOClcauseCPICHEcNo (ISHO Cancellation caused by CPICH Ec/No) .
721
ISHOClcauseCPICHrscp (ISHO Cancellation caused by CPICH RSCP). .
722
ISHOClcauseTxPwrDL (ISHO Cancellation caused by DL DPCH TX Power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
ISHOClcauseTxPwrUL (ISHO Cancellation caused by UE TX Power) 724
MaxBSICIdentTime (Maximum BSIC Identification Time) . . . . . . . . . . 725
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
DN00211177
Issue 12B
15.5
15.6
15.7
15.8
15.9
15.10
15.11
15.12
15.13
15.14
15.15
15.16
15.17
15.18
15.19
15.20
15.21
15.22
15.23
15.24
15.25
15.26
15.27
DSRepBasedSHO (Detected Set Reporting Based SHO). . . . . . . . . . 765
DropReportingInterval (Drop Reporting Interval) . . . . . . . . . . . . . . . . . 767
DropTime (Drop Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 768
DropWindow (Drop Window) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 770
EDCHAddEcNoOffset (Allow E-DCH usage EcNo offset) . . . . . . . . . . 771
EDCHRemEcNoOffset (CPICH EcNo offset E-DCH usage removal) . 772
EcNoFilterCoefficient (CPICH Ec/No Filter Coefficient). . . . . . . . . . . . 774
FMCSChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . . 775
FMCSId (FMCS identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 776
HHoEcNoCancel (CPICH Ec/No HHO Cancellation). . . . . . . . . . . . . . 777
HHoEcNoCancelTime (CPICH Ec/No HHO Cancellation Time) . . . . . 779
HHoEcNoThreshold (CPICH Ec/No HHO Threshold) . . . . . . . . . . . . . 782
HHoEcNoTimeHysteresis (CPICH Ec/No HHO Time Hysteresis) . . . . 783
HHoRscpCancel (CPICH RSCP HHO Cancellation) . . . . . . . . . . . . . . 785
HHoRscpCancelTime (CPICH RSCP HHO Cancellation Time) . . . . . 787
HHoRscpFilterCoefficient (CPICH RSCP HHO Filter Coefficient) . . . . 790
HHoRscpThreshold (CPICH RSCP HHO Threshold) . . . . . . . . . . . . . 791
HHoRscpTimeHysteresis (CPICH RSCP HHO Time Hysteresis) . . . . 793
IMSIbasedSHO (IMSI Based SHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . 795
MaxActiveSetSize (Maximum Active Set Size) . . . . . . . . . . . . . . . . . . 796
ReplacementReportingInterval (Replacement Reporting Interval) . . . 797
ReplacementTime (Replacement Time) . . . . . . . . . . . . . . . . . . . . . . . 799
ReplacementWindow (Replacement Window). . . . . . . . . . . . . . . . . . . 801
16
16.1
16.2
16.3
16.4
16.5
16.6
16.7
16.8
16.9
16.10
16.11
16.12
16.13
HOPG Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 803
AdjgHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . 803
AdjgHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . . 804
AdjgMinRxLevNCHO (Minimum RX level for non-critical HO). . . . . . . 805
AdjgPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . . 806
AdjgPenaltyTimeNCHO (Penalty time for GSM cell in non-critical HO) 807
AdjgPriorityCoverage (Ncell Priority for Coverage HO) . . . . . . . . . . . . 808
AdjgPrioritySLHO (Neighbour cell priority for SLHO). . . . . . . . . . . . . . 809
AdjgQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . 810
AdjgQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . 811
AdjgRxLevMinHO (Minimum RX Level for Coverage HO). . . . . . . . . . 812
AdjgTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . . 813
HOPGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 814
HOPGId (HOPG Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 816
17
17.1
17.2
17.3
17.4
17.5
17.6
17.7
17.8
HOPI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 817
AdjiEcNoMargin (CPICH Ec/No Margin for IFHO) . . . . . . . . . . . . . . . . 817
AdjiHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . . 818
AdjiHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . . 819
AdjiMinEcNo (Minimum CPICH Ec/No for IFHO). . . . . . . . . . . . . . . . . 820
AdjiMinEcNoNCHO (Minimum CPICH Ec/No for non-critical IFHO) . . 820
AdjiMinRSCP (Minimum CPICH RSCP for IFHO) . . . . . . . . . . . . . . . . 821
AdjiMinRscpNCHO (Minimum CPICH RSCP for non-critical IFHO) . . 822
AdjiPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . . 823
Id:0900d805809d7397
29
WCDMA Radio Network Configuration Parameters
17.9
17.15
17.16
17.17
17.18
17.19
17.20
17.21
17.22
17.23
17.24
17.25
AdjiPenaltyTimeNCHO (Penalty time for WCDMA cell in non-critical HO) .
824
AdjiPlossMargin (Pathloss Margin for IFHO) . . . . . . . . . . . . . . . . . . . . 825
AdjiPriorityCoverage (Ncell Priority for Coverage IFHO) . . . . . . . . . . . 826
AdjiPriorityDCellCAHO (Neighbour cell priority for DC HSDPA Capa Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 827
AdjiPriorityHSCAHO (Neighbour Cell Priority for HSPA Capability Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 829
AdjiPriorityMIMOCAHO (Neighbour cell priority for MIMO Capa Based HO)
830
AdjiPriorityQuality (Ncell Priority for Quality IFHO) . . . . . . . . . . . . . . . . 831
AdjiPrioritySLHO (Neighbour cell priority for service and load IFHO) . . 832
AdjiQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . . 833
AdjiQoffset2 (Cell Re-selection Quality Offset 2) . . . . . . . . . . . . . . . . . 834
AdjiQqualMin (Cell Re-selection Minimum Quality) . . . . . . . . . . . . . . . 835
AdjiQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . . 836
AdjiTempOffset1 (Cell Re-selection Temporary Offset 1). . . . . . . . . . . 837
AdjiTempOffset2 (Cell Re-selection Temporary Offset 2). . . . . . . . . . . 838
BlindHORSCPThr (Blind HO RSCP threshold). . . . . . . . . . . . . . . . . . . 840
HOPIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 841
HOPIId (HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 842
18
18.1
18.2
18.3
18.4
18.5
18.6
HOPL Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 843
AdjLAbsPrioCellReselec (Cell Reselection Absolute Priority) . . . . . . . 843
AdjLQrxlevminEUTRA (Cell Reselection Minimum RX level) . . . . . . . . 844
AdjLThreshigh (Cell Reselection Threshold high). . . . . . . . . . . . . . . . . 845
AdjLThreslow (Cell Reselection Threshold low) . . . . . . . . . . . . . . . . . . 845
HOPLChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 846
HOPLId (HOPL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 848
19
19.1
19.2
19.3
19.4
19.5
19.6
19.7
19.8
19.9
19.10
19.11
19.12
19.13
19.14
19.15
19.16
19.17
HOPS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 849
AdjsHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . . 849
AdjsHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . . 850
AdjsPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . . 851
AdjsQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . . 852
AdjsQoffset2 (Cell Re-selection Quality Offset 2) . . . . . . . . . . . . . . . . . 853
AdjsQqualMin (Cell Re-selection Minimum Quality) . . . . . . . . . . . . . . . 854
AdjsQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . . 855
AdjsTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . . . 856
AdjsTempOffset2 (Cell Re-selection Temporary Offset 2) . . . . . . . . . . 857
EcNoAveragingWindow (CPICH Ec/No Averaging Window) . . . . . . . . 858
EnableInterRNCsho (Enable Inter-RNC Soft Handover) . . . . . . . . . . . 859
EnableRRCRelease (Enable RRC Connection Release) . . . . . . . . . . . 860
HHOMarginAverageEcNo (HHO Margin for Average Ec/No) . . . . . . . . 862
HHOMarginPeakEcNo (HHO Margin for Peak Ec/No) . . . . . . . . . . . . . 863
HOPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 864
HOPSId (HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865
HSDPAAvailabilityIur (HSDPA availability of the neighbouring DRNC cell)
866
17.10
17.11
17.12
17.13
17.14
30
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
19.18
DN00211177
Issue 12B
19.19
19.20
HSUPAAvailabilityIur (HSUPA availability of the neighbouring DRNC cell)
867
ReleaseMarginAverageEcNo (Release Margin for Average Ec/No) . . 868
ReleaseMarginPeakEcNo (Release Margin for Peak Ec/No) . . . . . . . 869
20
20.1
20.2
20.3
20.4
20.5
20.6
20.7
20.8
20.9
20.10
20.11
20.12
20.13
20.14
20.15
20.16
IPNB Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 871
CNBAP (C-NBAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 871
CNBAPConnOpState (C-NBAP connection operational state) . . . . . . 872
CNBAPICSUIndex (ICSU index for C-NBAP link) . . . . . . . . . . . . . . . . 873
SCTPPortNumberCNBAP (SCTP Port Number for C-NBAP) . . . . . . . 873
DNBAP (D-NBAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 874
CControlPortID (Communication Control Port identifier) . . . . . . . . . . . 875
DNBAPConnOpState (D-NBAP connection operational state) . . . . . . 876
DNBAPICSUIndex (ICSU index for D-NBAP link) . . . . . . . . . . . . . . . . 877
SCTPPortNumberDNBAP (SCTP Port Number for D-NBAP) . . . . . . . 878
IPBasedRouteId (IP Based Route Identification) . . . . . . . . . . . . . . . . . 879
IPNBChangeOrigin (IPNB Change origin) . . . . . . . . . . . . . . . . . . . . . . 880
IPNBId (IPNB object identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
MinSCTPPortIub (Minimum SCTP port number) . . . . . . . . . . . . . . . . . 882
NBAPDSCP (NBAP DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 883
NodeBIPAddress (Control Plane Destination Address Iub) . . . . . . . . . 884
WBTSId (WBTS identification). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 885
21
21.1
21.2
21.3
21.4
21.5
21.6
21.7
21.8
IPQM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 887
BackgroundTCToDSCP (Background TC to DSCP mapping). . . . . . . 887
ConversationalTCToDSCP (Conversational TC to DSCP mapping) . . 888
IPQMChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 889
IPQMId (IP Qos Management Identifier) . . . . . . . . . . . . . . . . . . . . . . . 890
InteractiveTHP1TCToDSCP (Interactive THP1 TC to DSCP mapping) 891
InteractiveTHP2TCToDSCP (Interactive THP2 TC to DSCP mapping) 892
InteractiveTHP3TCToDSCP (Interactive THP3 TC to DSCP mapping) 893
StreamingTCToDSCP (Streaming TC to DSCP mapping) . . . . . . . . . 894
22
22.1
22.2
22.3
22.4
22.5
22.6
22.7
22.8
22.9
22.10
22.11
22.12
22.13
22.14
22.15
IUCS Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896
AAL2PTSigForIuCS (AAL2PT signalling for IuCS) . . . . . . . . . . . . . . . 896
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . . 897
CNId (Core Network Identity). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 898
CSCNNRI (NRI for CS Core routing) . . . . . . . . . . . . . . . . . . . . . . . . . . 899
NRIMaxForCSCN (Maximum value of NRI range for CS Core routing) 900
NRIMinForCSCN (Minimum value of NRI range for CS Core routing) 901
CSFlexiIuWeight (CS Flexible Iu Weight) . . . . . . . . . . . . . . . . . . . . . . 902
DefaultCN (Default Core Network). . . . . . . . . . . . . . . . . . . . . . . . . . . . 904
IUCSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 905
IUCSId (IuCS Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 906
IUOIdentifier (IUO Object Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . 907
IuState (State of Iu interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 908
MinUDPPortCS (Minimum UDP Port) . . . . . . . . . . . . . . . . . . . . . . . . . 909
NetworkInd (Network indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910
RelocationSupport (Serving RNC Relocation Support) . . . . . . . . . . . . 912
Id:0900d805809d7397
31
WCDMA Radio Network Configuration Parameters
32
22.16
22.17
22.18
22.19
22.20
22.21
RtcpActivation (RTCP activation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . . . 914
TRafC (TRafC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915
TRatC (TRatC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 916
TigOR (TigOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917
TinTR (TinTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 918
23
23.1
23.2
23.3
23.4
23.5
23.6
IUCSIP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 920
DestIPAddressCS (IP address for the IUCS destination subnet) . . . . . 920
IPBasedRouteIdCS (IP Based Route Identifier for IUCS). . . . . . . . . . . 921
IPNetmaskCS (IP netmask for the IUCS destination subnet) . . . . . . . . 922
IPQMIdCS (IPQM object id for IuCS) . . . . . . . . . . . . . . . . . . . . . . . . . . 924
IUCSIPChangeOrigin (IUCSIP Change Origin) . . . . . . . . . . . . . . . . . . 925
IUCSIPId (IUCSIP Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 926
24
24.1
24.2
24.3
24.4
24.5
24.6
24.7
24.8
24.9
24.10
24.11
24.12
24.13
24.14
24.15
24.16
24.17
24.18
24.19
24.20
24.21
24.22
24.23
24.24
24.25
24.26
24.27
24.28
24.29
24.30
24.31
24.32
IUO Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 928
CSCNDRXLength (CN CS domain specific DRX cycle length) . . . . . . 928
CS_T3212 (T3212) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 929
ICROperatorId (ICR Operator Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 930
ICROperatorName (ICR Operator Name). . . . . . . . . . . . . . . . . . . . . . . 931
ICRPLMNid (ICR PLMN Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 932
MCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 934
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . . . 935
IUOChangeOrigin (IUO Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . 936
IUOId (IUO Identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 937
IuBarringDelayTimerCS (Iu Barring Delay Timer for CS) . . . . . . . . . . . 938
IuBarringDelayTimerPS (Iu Barring Delay Timer for PS) . . . . . . . . . . . 939
IuBarringRecoveryGroupCS (Iu Barring Recovery Group for CS) . . . . 940
IuBarringRecoveryGroupPS (Iu Barring Recovery Group for PS) . . . . 941
IuBarringRecoveryTimerCS (Iu service barring recovery timer for CS) 942
IuBarringRecoveryTimerPS (Iu service barring recovery timer for PS) 943
IubTransportSharingInd (Iub Transport Sharing index) . . . . . . . . . . . . 945
NRILengthForCSCN (NRI length for CS Core Networks) . . . . . . . . . . . 946
NRILengthForPSCN (NRI length for PS Core Networks) . . . . . . . . . . . 947
NullNRIForCSPool (Null NRI value for CS Pool) . . . . . . . . . . . . . . . . . 948
NullNRIForPSPool (Null NRI value for PS Pool). . . . . . . . . . . . . . . . . . 949
OperatorWeight (Operator Weight). . . . . . . . . . . . . . . . . . . . . . . . . . . . 950
PLMNid (PLMN identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 952
MCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . . . 955
PSCNDRXLength (CN PS domain specific DRX cycle length). . . . . . . 956
PS_NMO (Network Mode of Operation) . . . . . . . . . . . . . . . . . . . . . . . . 958
SharedAreaPLMNid (Shared area PLMN identity) . . . . . . . . . . . . . . . . 959
SharedAreaMCC (Shared area Mobile Country Code). . . . . . . . . . . . . 961
SharedAreaMNC (Shared area Mobile Network Code) . . . . . . . . . . . . 962
SharedAreaMNClength (Shared area Mobile Network Code Length) . 963
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
25
25.1
25.2
25.3
25.4
25.5
25.6
25.7
25.8
25.9
25.10
25.11
25.12
25.13
25.14
25.15
25.16
25.17
25.18
25.19
25.20
IUPS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 964
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . . 964
CNId (Core Network Identity). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965
CellFACHRelocSupport (Cell_FACH state Serving RNC Relocation Support ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 966
DefaultCN (Default Core Network). . . . . . . . . . . . . . . . . . . . . . . . . . . . 967
IUOIdentifier (IUO Object Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . 968
IUPSChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . . . 969
IUPSId (IuPS Interface Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 970
IuState (State of Iu interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971
NetworkInd (Network indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 972
PSCNNRI (NRI for PS Core routing) . . . . . . . . . . . . . . . . . . . . . . . . . . 974
NRIMaxForPSCN (Maximum value of NRI range for PS Core routing) 975
NRIMinForPSCN (Minimum value of NRI range for PS Core routing). 976
PSFlexiIuWeight (PS Flexible Iu Weight). . . . . . . . . . . . . . . . . . . . . . . 977
RelocationSupport (Serving RNC Relocation Support) . . . . . . . . . . . . 979
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . . 980
TDataFwd (T DATAfwd). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 981
TRafC (TRafC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 982
TRatC (TRatC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983
TigOR (TigOR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983
TinTR (TinTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 984
26
26.1
26.2
26.3
26.4
26.5
26.6
IUPSIP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 986
DestIPAddressPS (IP address for the IUPS destination subnet). . . . . 986
IPBasedRouteIdPS (IP Based Route Identifier for IUPS) . . . . . . . . . . 988
IPNetmaskPS (IP netmask for the IUPS destination subnet) . . . . . . . 989
IPQMIdPS (IPQM object id for IuPS) . . . . . . . . . . . . . . . . . . . . . . . . . . 991
IUPSIPChangeOrigin (IUPSIP Change Origin) . . . . . . . . . . . . . . . . . . 992
IUPSIPId (IUPSIP Identifier ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 993
27
27.1
27.2
27.3
IUR Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 995
AAL2PTSigForIur (AAL2PT signalling for Iur) . . . . . . . . . . . . . . . . . . . 995
AppAwareRANEnabled (Application Aware RAN Enabled). . . . . . . . . 996
CellFACHnRncRelocSupport (Cell_FACH state Serving RNC Relocation
Support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 997
DSCPHighIur (DSCP high priority for Iur) . . . . . . . . . . . . . . . . . . . . . . 998
DSCPLowIur (Low priority DSCP for Iur) . . . . . . . . . . . . . . . . . . . . . . . 999
DSCPMedDCHIur (DSCP medium priority on R99 DCH for Iur) . . . . 1000
DelayThresholdMaxIur (Maximum Threshold for HSUPA congestion handling delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1001
DelayThresholdMidIur (Middle Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1002
DelayThresholdMinIur (Minimum Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1004
HSDPACCEnabledIur (HSDPA Congestion Control activation Iur) . . 1005
HSDPAULCToDSCPIur (HSDPA UL FP Control traffic to DSCP mapping
Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006
HSPAOverIur (HSPA over Iur). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
27.4
27.5
27.6
27.7
27.8
27.9
27.10
27.11
27.12
DN00211177
Issue 12B
Id:0900d805809d7397
33
WCDMA Radio Network Configuration Parameters
27.13
27.14
27.15
27.16
27.17
27.18
27.19
27.20
27.21
27.22
27.23
27.24
27.25
27.26
27.27
27.28
27.29
27.30
27.31
27.32
27.33
27.34
27.35
27.36
27.37
27.38
27.39
28
28.1
28.2
28.3
28.4
28.5
28.6
28.7
28.8
28.9
28.10
34
HSUPADLCToDSCPIur (HSUPA DL FP Control traffic to DSCP mapping
Iur). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1009
IBTSSharing (IBTS Sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010
IPBasedRouteIdIur (IP based route identifier) . . . . . . . . . . . . . . . . . . 1011
IURChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1012
IURId (Iur Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1013
InterfaceMode (Configure the IUR in a special mode) . . . . . . . . . . . . 1014
IurUPSupport (User Plane support of Iur connection) . . . . . . . . . . . . 1015
MaxFPDLFrameSizeIur (Maximum FP downlink frame size Iur) . . . . 1016
MaxIurNRTHSDSCHBitRate (Maximum NRT HS-DSCH MAC-d flow bit
rate over Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1017
MinUDPPortIur (Minimum UDP port value) . . . . . . . . . . . . . . . . . . . . 1018
NRncId (Neighbour RNC identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . 1019
NRncNetworkInd (Network indicator of neighbour RNC) . . . . . . . . . . 1021
NRncRelocationSupport (Serving RNC Relocation Support of neighbour
RNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1022
NRncSignPointCode (Signalling point code of neighbour RNC). . . . . 1023
NRncVersion (Release version of Neighbouring RNC) . . . . . . . . . . . 1024
NeighbouringPLMNid (Neighbouring PLMN identity) . . . . . . . . . . . . . 1026
MCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1028
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . . 1029
NeighbouringRNWElement (Type of the Neighbouring RNW Element) . . .
1030
OverbookingSwitchIur (Overbooking Switch Iur) . . . . . . . . . . . . . . . . 1031
ProbabilityFactorMaxIur (ProbabilityFactor for Congestion Indication sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1032
RNSAPCongAndPreemption (RNSAP Congestion And Preemption) 1033
ToAWEOffsetNRTDCHIP (ToAWE Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1034
ToAWEOffsetRTDCHIP (ToAWE Offset for RT DCH connections over IP)
1035
ToAWSOffsetNRTDCHIP (ToAWS Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1036
ToAWSOffsetRTDCHIP (ToAWS Offset for RT DCH connections over IP)
1037
PFL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1038
AMRToNonPreferredLayer (AMR to Non Preferred Layer) . . . . . . . . 1038
BlindHORSCPThrAbove (Blind HO RSCP threshold above) . . . . . . . 1039
BlindHORSCPThrBelow (Blind HO RSCP threshold below) . . . . . . . 1040
LaySelLowLoadPref (Layer Selection Low Load Preferred) . . . . . . . . 1041
LaySelWeightBand (Layer Selection Weight of Band) . . . . . . . . . . . . 1042
LaySelWeightLoad (Layer Selection Weight of Load) . . . . . . . . . . . . 1042
LaySelWeightPrefLayer (Layer Selection Weight of Preferred Layer) 1043
LaySelWeightRSCP (Layer Selection Weight of RSCP) . . . . . . . . . . 1044
PFL64QAMAMR (Preferred Frequency Layer for 64QAM AMR) . . . . 1045
PrefLayer64QAMAMR (Preferred Layer for 64QAM AMR) . . . . . . . . 1046
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
28.11
28.12
28.13
28.14
28.15
28.16
28.17
28.18
28.19
28.20
28.21
28.22
28.23
28.24
28.25
28.26
28.27
28.28
28.29
28.30
28.31
28.32
28.33
28.34
28.35
28.36
28.37
28.38
28.39
28.40
28.41
28.42
28.43
DN00211177
Issue 12B
PFL64QAMAMRNRT (Preferred Frequency Layer for 64QAM AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1047
PrefLayer64QAMAMRNRT (Preferred Layer for 64QAM AMR and NRT).
1048
PFL64QAMNRT (Preferred Frequency Layer for 64QAM NRT) . . . . 1049
PrefLayer64QAMNRT (Preferred Layer for 64QAM NRT). . . . . . . . . 1050
PFL64QAMStr (Preferred Frequency Layer for 64QAM Streaming) . 1051
PrefLayer64QAMStr (Preferred Layer for 64QAM Streaming) . . . . . 1052
PFLCSHSAMR (Preferred Frequency Layer for CS voice HSPA AMR) . .
1053
PrefLayerCSHSAMR (Preferred Layer for CS voice HSPA AMR). . . 1054
PFLCSHSAMRNRT (Preferred Frequency Layer for CS voice HSPA AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1055
PrefLayerCSHSAMRNRT (Preferred Layer for CS voice HSPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1056
PFLCSHSNRT (Preferred Frequency Layer for CS voice HSPA NRT). . .
1057
PrefLayerCSHSNRT (Preferred Layer for CS voice HSPA NRT) . . . 1058
PFLCSHSStr (Preferred Frequency Layer for CS voice HSPA Streaming)
1059
PrefLayerCSHSStr (Preferred Layer for CS voice HSPA Streaming) 1060
PFLChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 1061
PFLDBHSDAMR (Preferred Frequency Layer for DB-DC-HSDPA AMR) .
1063
PrefLayerDBHSDAMR (Preferred Layer for DB-DC-HSDPA AMR) . 1063
PFLDBHSDAMRNRT (Preferred Frequency Layer for DB-DC-HSDPA
AMR and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1065
PrefLayerDBHSDAMRNRT (Preferred Layer for DB-DC-HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1066
PFLDBHSDNRT (Preferred Frequency Layer for DB-DC-HSDPA NRT) .
1067
PrefLayerDBHSDNRT (Preferred Layer for DB-DC-HSDPA NRT) . . 1067
PFLDBHSDStr (Preferred Frequency Layer for DB-DC-HSDPA Streaming)
1069
PrefLayerDBHSDStr (Preferred Layer for DB-DC-HSDPA Streaming) . . .
1069
PFLDCHSDAMR (Preferred Frequency Layer for DC-HSDPA AMR) 1070
PrefLayerDCHSDAMR (Preferred Layer for DC-HSDPA AMR) . . . . 1071
PFLDCHSDAMRNRT (Preferred Frequency Layer for DC-HSDPA AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1072
PrefLayerDCHSDAMRNRT (Preferred Layer for DC-HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1073
PFLDCHSDNRT (Preferred Frequency Layer for DC-HSDPA NRT) 1074
PrefLayerDCHSDNRT (Preferred Layer for DC-HSDPA NRT) . . . . . 1075
PFLDCHSDStr (Preferred Frequency Layer for DC-HSDPA Streaming) .
1076
PrefLayerDCHSDStr (Preferred Layer for DC-HSDPA Streaming) . . 1077
PFLDCMIAMR (Preferred Frequency Layer for DC and MIMO AMR) 1078
PrefLayerDCMIAMR (Preferred Layer for DC and MIMO AMR) . . . . 1079
Id:0900d805809d7397
35
WCDMA Radio Network Configuration Parameters
28.44
28.45
28.46
28.47
28.48
28.49
28.50
28.51
28.52
28.53
28.54
28.55
28.56
28.57
28.58
28.59
28.60
28.61
28.62
28.63
28.64
28.65
28.66
28.67
28.68
28.69
28.70
28.71
28.72
28.73
28.74
28.75
28.76
28.77
28.78
28.79
28.80
36
PFLDCMIAMRNRT (Preferred Frequency Layer for DC and MIMO AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1080
PrefLayerDCMIAMRNRT (Preferred Layer for DC and MIMO AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1081
PFLDCMINRT (Preferred Frequency Layer for DC and MIMO NRT) . 1082
PrefLayerDCMINRT (Preferred Layer for DC and MIMO NRT) . . . . . 1083
PFLDCMIStr (Preferred Frequency Layer for DC and MIMO Streaming). .
1084
PrefLayerDCMIStr (Preferred Layer for DC and MIMO Streaming) . . 1085
PFLFDPCHAMR (Preferred Frequency Layer for FDPCH AMR) . . . . 1086
PrefLayerFDPCHAMR (Preferred Layer for F-DPCH AMR) . . . . . . . . 1087
PFLFDPCHAMRNRT (Preferred Frequency Layer for FDPCH AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1088
PrefLayerFDPCHAMRNRT (Preferred Layer for F-DPCH AMR and NRT)
1089
PFLFDPCHNRT (Preferred Frequency Layer for FDPCH NRT) . . . . 1090
PrefLayerFDPCHNRT (Preferred Layer for F-DPCH NRT) . . . . . . . . 1091
PFLFDPCHStr (Preferred Frequency Layer for FDPCH Streaming) . 1092
PrefLayerFDPCHStr (Preferred Layer for F-DPCH Streaming) . . . . . 1093
PFLFastMovUECS (Preferred Frequency Layer for fast moving UE CS). .
1094
PrefLayerFastMovUECS (Preferred Layer for fast moving UE CS) . . 1095
PFLFastMovUEPS (Preferred Frequency Layer for fast moving UE PS) . .
1096
PrefLayerFastMovUEPS (Preferred Layer for fast moving UE PS) . . 1097
PFLHSDPAAMR (Preferred Frequency Layer for HSDPA AMR) . . . . 1098
PrefLayerHSDPAAMR (Preferred Layer for HSDPA AMR) . . . . . . . . 1099
PFLHSDPAAMRNRT (Preferred Frequency Layer for HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100
PrefLayerHSDPAAMRNRT (Preferred Layer for HSDPA AMR and NRT) .
1101
PFLHSDPANRT (Preferred Frequency Layer for HSDPA NRT) . . . . 1102
PrefLayerHSDPANRT (Preferred Layer for HSDPA NRT) . . . . . . . . . 1103
PFLHSDPAStr (Preferred Frequency Layer for HSDPA Streaming) . 1104
PrefLayerHSDPAStr (Preferred Layer for HSDPA Streaming) . . . . . . 1105
PFLHSPAAMR (Preferred Frequency Layer for HSPA AMR) . . . . . . 1106
PrefLayerHSPAAMR (Preferred Layer for HSPA AMR) . . . . . . . . . . . 1107
PFLHSPAAMRNRT (Preferred Frequency Layer for HSPA AMR and NRT)
1108
PrefLayerHSPAAMRNRT (Preferred Layer for HSPA AMR and NRT) . . .
1109
PFLHSPANRT (Preferred Frequency Layer for HSPA NRT) . . . . . . . 1110
PrefLayerHSPANRT (Preferred Layer for HSPA NRT) . . . . . . . . . . . 1111
PFLHSPAStr (Preferred Frequency Layer for HSPA Streaming) . . . . 1112
PrefLayerHSPAStr (Preferred Layer for HSPA Streaming) . . . . . . . . 1113
PFLIdentifier (PFL Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1114
PFLMIMOAMR (Preferred Frequency Layer for MIMO AMR) . . . . . . 1115
PrefLayerMIMOAMR (Preferred Layer for MIMO AMR) . . . . . . . . . . . 1116
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
28.81
28.90
28.91
28.92
28.93
28.94
PFLMIMOAMRNRT (Preferred Frequency Layer for MIMO AMR and NRT)
1117
PrefLayerMIMOAMRNRT (Preferred Layer for MIMO AMR and NRT) . . .
1118
PFLMIMONRT (Preferred Frequency Layer for MIMO NRT) . . . . . . 1119
PrefLayerMIMONRT (Preferred Layer for MIMO NRT) . . . . . . . . . . . 1120
PFLMIMOStr (Preferred Frequency Layer for MIMO Streaming) . . . 1121
PrefLayerMIMOStr (Preferred Layer for MIMO Streaming) . . . . . . . . 1122
PFLR99AMR (Preferred Frequency Layer for R99 AMR) . . . . . . . . . 1123
PrefLayerR99AMR (Preferred Layer for R99 AMR). . . . . . . . . . . . . . 1124
PFLR99AMRNRT (Preferred Frequency Layer for R99 AMR and NRT). .
1125
PrefLayerR99AMRNRT (Preferred Layer for R99 AMR and NRT) . . 1126
PFLR99NRT (Preferred Frequency Layer for R99 NRT). . . . . . . . . . 1127
PrefLayerR99NRT (Preferred Layer for R99 NRT) . . . . . . . . . . . . . . 1128
PFLR99Str (Preferred Frequency Layer for R99 Streaming). . . . . . . 1129
PrefLayerR99Str (Preferred Layer for R99 Streaming) . . . . . . . . . . . 1130
29
29.1
29.2
29.3
29.4
29.5
29.6
PREBTS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1132
AutoConnHWID (Auto Connection Hardware ID) . . . . . . . . . . . . . . . 1132
AutoConnSiteID (Auto Connection site ID) . . . . . . . . . . . . . . . . . . . . 1133
BTSID (BTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1134
PREBTSID (PREBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1135
TechnologyInformation (Technology Information) . . . . . . . . . . . . . . . 1136
Version (Version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1137
30
30.1
30.2
30.3
30.4
30.5
30.6
RNAC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1138
AMRLoadTxPower (Indicator for downlink radio power load) . . . . . . 1138
AMRNumofReconf (AMRNumofReconf) . . . . . . . . . . . . . . . . . . . . . . 1139
AMRwinSizeSCload (AMRwinSizeSCload) . . . . . . . . . . . . . . . . . . . . 1139
AdjustmentPeriod (Adjustment period time) . . . . . . . . . . . . . . . . . . . 1140
AdjustmentRatio (Adjustment ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . 1142
AutoACDecRestHysNRTQ (Automatic Access Class Decrease Restriction
Level Hysteresis for NRT queue length trigger). . . . . . . . . . . . . . . . . 1143
AutoACDecRestHysRTWP (Automatic Access Class Decrease Restriction
Level Hysteresis for Received Total Wideband Power trigg). . . . . . . 1144
AutoACIncRestHysNRTQ (Automatic Access Class Increase Restriction
Level Hysteresis for NRT queue length trigger). . . . . . . . . . . . . . . . . 1145
AutoACIncRestHysRTWP (Automatic Access Class Increase Restriction
Level Hysteresis for Received Total Wideband Powertrigge) . . . . . . 1146
AutoACMaxRestLevel (Automatic Access Class Maximum Restriction Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1148
AutoACRLevelUpdInt (Automatic Access Class Restriction Level Update
Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149
AutoACRTrigRNCLoad (Automatic Access Class Restriction Trigger of
RNC Load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150
AutoACRestForCellPCH (Access Restriction for Cell_PCH state UE) 1152
BitRateSetPSNRT (Bit rate set for PS NRT DCHs) . . . . . . . . . . . . . . 1153
DCHSlopeOfTheCurve (DCH slope of the curve) . . . . . . . . . . . . . . . 1155
28.82
28.83
28.84
28.85
28.86
28.87
28.88
28.89
30.7
30.8
30.9
30.10
30.11
30.12
30.13
30.14
30.15
DN00211177
Issue 12B
Id:0900d805809d7397
37
WCDMA Radio Network Configuration Parameters
30.16
30.17
30.18
30.19
30.20
30.21
30.22
30.23
30.24
30.25
30.26
30.27
30.28
30.29
30.30
30.31
30.32
30.33
30.34
30.35
30.36
30.37
30.38
30.39
30.40
30.41
30.42
30.43
30.44
30.45
30.46
38
DLInLoopPCStepSizeCPC (DL inner loop PC step size for CPC users) . .
1156
DLLoadSource (DL Load Source). . . . . . . . . . . . . . . . . . . . . . . . . . . . 1157
DLmaxBitRatePerSF (Maximum DL bit rate per spreading factor) . . . 1158
DLmaxBitRateSF128 (Maximum DL bit rate with spreading factor 128) . .
1159
DLmaxBitRateSF16 (Maximum DL bit rate with spreading factor 16) 1161
DLmaxBitRateSF256 (Maximum DL bit rate with spreading factor 256) . .
1162
DLmaxBitRateSF32 (Maximum DL bit rate with spreading factor 32) 1163
DLmaxBitRateSF64 (Maximum DL bit rate with spreading factor 64) 1164
DLpuncturingLimit (Downlink puncturing limit) . . . . . . . . . . . . . . . . . . 1165
DownlinkInnerLoopPCStepSize (Power-adjusting step size in WCDMA
BTS for DL closed loop PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1167
DynHSUPABLERAlgTrgTime (Time to trigger Dyn HSUPA BLER Algorithm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1168
DynHSUPABLERBurstDataRx (Retransmissions in Dyn HSUPA BLER for
Bursty Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1169
DynHSUPABLERContDataRx10 (Retransmissions in Dyn HSUPA BLER
for Cont Data 10msTTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1170
DynHSUPABLERContDataRx2 (Retransmissions in Dyn HSUPA BLER for
Cont Data 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1172
DynHSUPABLERFrameWinSiz (Window size for FP Frames Measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1173
DynHSUPABLERMaxRateThrB (Peak rate threshold for bursty data of Dyn
HSUPA BLER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1174
DynHSUPABLERMaxRateThrC10 (Peak rate thr for cont data of Dyn HSUPA BLER 10 ms TTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1175
DynHSUPABLERMaxRateThrC2 (Peak rate thr for cont data of Dyn HSUPA BLER 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1176
DynHSUPABLERPeakRateRx (Retransmissions in Dyn HSUPA BLER for
Peak data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1178
DynHSUPABLERThrBurstyTP (Bursty Data throughput threshold per TTI)
1179
DynHSUPABurstyPeriod (Bursty Period for Dyn HSUPA BLER) . . . . 1180
EDCHSlopeOfTheCurve (EDCH slope of the curve) . . . . . . . . . . . . . 1181
ExpectReorderingPDCP (Expect Reordering for PDCP) . . . . . . . . . . 1182
FOLPCSIRTgtModInt (Faster OLPC SIR target modification interval) 1183
FOLPCStepSizSIRTgt (Faster OLPC step size of SIR target changes) . . .
1184
FmaxPeriodPDCP (F Max Period for PDCP) . . . . . . . . . . . . . . . . . . . 1186
FmaxTimePDCP (F Max Time for PDCP) . . . . . . . . . . . . . . . . . . . . . 1187
FreePtxSafetyMarginStr (Safety margin for free transmitted power for
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1188
GainFactorControlPartPRACHmessage (Gain factor for control part of
PRACH message). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189
PrachBetaC120 (Gain factor for control part of PRACH message with 120
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1190
PrachBetaC15 (Gain factor for control part of PRACH message with 15
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1191
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
30.47
30.48
30.49
30.50
30.51
30.52
30.53
30.54
30.55
30.56
30.57
30.58
30.59
30.60
30.61
30.62
30.63
30.64
30.65
30.66
30.67
30.68
30.69
30.70
30.71
30.72
30.73
30.74
30.75
DN00211177
Issue 12B
PrachBetaC30 (Gain factor for control part of PRACH message with 30
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1192
PrachBetaC60 (Gain factor for control part of PRACH message with 60
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1193
GainFactorDataPartPRACHmessage (Gain factor for data part of PRACH
message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1194
PrachBetaD120 (Gain factor for data part of PRACH message with 120
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1196
PrachBetaD15 (Gain factor for data part of PRACH message with 15 ksps)
1197
PrachBetaD30 (Gain factor for data part of PRACH message with 30 ksps)
1198
PrachBetaD60 (Gain factor for data part of PRACH message with 60 ksps)
1199
HSFACHDiscardTimer (Discard Timer for BCCH, CCCH and DCCH data
on HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200
HSFACHResetTimer (MAC-ehs Reset Timer for xCCH data on HS-FACH)
1201
HeaderCompressionMethod (Header compression algorithm of PDCP). .
1202
ICRHostOperatorId (ICR Host Operator Identifier) . . . . . . . . . . . . . . 1203
L1BurstDataBLERTrgtEDCH (Layer1 Bursty Data BLER target for E-DCH)
1205
L1ContBLERTrgtEDCH10 (Layer1 Continuous BLER target for E-DCH TTI
10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1206
L1ContBLERTrgtEDCH2 (Layer1 Continuous BLER target for E-DCH TTI
2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1207
L1PeakRateBLERTrgtEDCH (Layer1 Peak Data Rate BLER target for EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1209
LoadBasedAMRCodecMode (Usage of Load based AMR codec mode selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1210
MaxAdjustmentStep (Maximum adjustment step) . . . . . . . . . . . . . . . 1211
MaxFreezingTime (Maximum freezing time) . . . . . . . . . . . . . . . . . . . 1212
MaxHeaderPDCP (Max Header for PDCP) . . . . . . . . . . . . . . . . . . . . 1213
MaxNumberOfReAttemptsCong (Maximum number of re-attempts to hunt
resources) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1214
MinPrefChange (Trigger for sending the updated reference power to BTSs)
1215
NonTCPspacePDCP (Non-TCP Space for PDCP) . . . . . . . . . . . . . . 1217
PCPreamble (Uplink DPCCH power control preamble). . . . . . . . . . . 1218
PCrangeDL (Radio link downlink power control range) . . . . . . . . . . . 1219
PTTUEMappingARPCap (PTT UE mapping for ARP pre-emption capability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1220
PTTUEMappingARPPrioLevel (PTT UE mapping for ARP priority level) .
1222
PTTUEMappingARPQue (PTT UE Mapping for ARP queuing allowed) . .
1224
PTTUEMappingARPVul (PTT UE mapping for ARP pre-emption vulnerability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1225
PTTUEMappingSignInd (PTT UE mapping for Signaling indication) . 1227
Id:0900d805809d7397
39
WCDMA Radio Network Configuration Parameters
30.76
30.77
30.78
30.79
30.80
30.81
30.82
30.83
30.84
30.85
30.86
30.87
30.88
30.89
30.90
30.91
30.92
30.93
30.94
30.95
30.96
30.97
30.98
30.99
30.100
30.101
30.102
30.103
30.104
30.105
30.106
31
31.1
31.2
31.3
31.4
31.5
31.6
31.7
40
PTTUEMappingTC (PTT UE mapping for Traffic Class) . . . . . . . . . . 1229
PTTUEMappingTHP (PTT UE mapping for Traffic handling priority) . 1230
PagingRestrictionInd (Paging Restriction Indication for PPAC) . . . . . 1232
PeriodULRCAMR (Period for CS AMR RRC TFC control requests) . 1233
PrefSubtract (Reference power subtraction parameter) . . . . . . . . . . . 1235
RAU_LAU_RestrictionInd (RAU and LAU Restriction Indication for PPAC)
1236
RNACChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 1237
RNACId (RNAC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1238
RNARDSACCell_DCH (Access class restriction level for Cell_DCH) 1239
RNARDSACCell_PCH (Access class restriction level for Cell_PCH) . 1241
RNARDSACGuardTime (Access class restriction guard time) . . . . . . 1242
RRCConnSetupMsgSize (RRC Connection Setup Message Size Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1243
SRBDelay (SRB delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1245
SignallingLinkInactivityTimer (Signalling link inactivity timer) . . . . . . . 1246
StepSizeForDCHBLER (Step Size for DCH BLER calculation) . . . . . 1247
StepSizeForEDCHBLER (Step Size for EDCH BLER calculation) . . . 1248
TCPspacePDCP (TCP Space for PDCP) . . . . . . . . . . . . . . . . . . . . . . 1249
TDMultForHSDPAStreaming (Transfer Delay multiplier for HSDPA streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250
TFDCHZeroBitRate (Zero size transport block to L1 CRC calculation) . . .
1251
ULFastOLPCDTXthld (DTX threshold for uplink faster outer loop). . . 1253
ULmaxBitRatePerSF (Maximum UL bit rate per spreading factor) . . . 1254
ULmaxBitRateSF128 (Maximum UL bit rate with spreading factor 128) . .
1255
ULmaxBitRateSF16 (Maximum UL bit rate with spreading factor 16) 1256
ULmaxBitRateSF256 (Maximum UL bit rate with spreading factor 256) . .
1257
ULmaxBitRateSF32 (Maximum UL bit rate with spreading factor 32) 1258
ULmaxBitRateSF64 (Maximum UL bit rate with spreading factor 64) 1260
ULmaxBitRateSF8 (Maximum UL bit rate with spreading factor 8) . . 1261
ULpuncturingLimit (Uplink puncturing limit) . . . . . . . . . . . . . . . . . . . . 1262
UlScrCodeMin (Uplink scrambling code minimum value) . . . . . . . . . . 1263
UpLinkInitialTransmitPowerMode (Initial transmit power in uplink compressed mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1265
UpLinkRecoveryPeriodPowerMode (Recovery Period Power in UL Compressed Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1266
RNC Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1268
AlarmSetforWCELBLINIT (Alarm Set for WCEL BL-INIT) . . . . . . . . . 1268
CBCSourceIPAddress (Source IP address for IuBC interface) . . . . . 1269
CSAttachDetachAllowed (Attach-detach allowed) . . . . . . . . . . . . . . . 1270
CommonMCC (Common MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1271
CommonMNC (Common MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1272
CommonMNCLength (Common MNC Length) . . . . . . . . . . . . . . . . . . 1273
ConnectionRetryCounter (OAM Connection Establishment Retry Counter)
1274
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
31.8
31.9
31.10
31.11
31.12
31.13
31.14
31.15
31.16
31.17
31.18
31.19
31.20
31.21
31.22
31.23
31.24
31.25
31.26
31.27
31.28
31.29
31.30
31.31
31.32
31.33
31.34
31.35
31.36
31.37
31.38
31.39
31.40
31.41
31.42
31.43
31.44
31.45
31.46
31.47
31.48
31.49
DN00211177
Issue 12B
DLBLERConfInterval (Downlink measured BLER confidence interval) . . .
1275
DSCPStatisticsGroupA (DSCP statistics group A ) . . . . . . . . . . . . . . 1277
DSCPStatisticsGroupB (DSCP statistics group B) . . . . . . . . . . . . . . 1278
DSCPStatisticsGroupC (DSCP statistics group C) . . . . . . . . . . . . . . 1279
DSCPStatisticsGroupTCPack (DSCP code for DL TCP Ack statistics). . .
1280
EmergencyCallRedirectTimer (Emergency Call Redirect Timer). . . . 1282
ExtendedULDLactivationTmr (Extended Cell_FACH inactivity supervision
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1283
LCSSupportForAnchoring (LCS Support for Anchoring) . . . . . . . . . . 1284
LCSfunctionality (LCS functionality). . . . . . . . . . . . . . . . . . . . . . . . . . 1285
MACLogicalChPriority (MAC logical channel priority definition) . . . . 1286
MACLogChPriSRB1 (MAC logical channel priority for SRB1) . . . . . . 1287
MACLogChPriSRB2 (MAC logical channel priority for SRB2) . . . . . . 1288
MACLogChPriSRB3 (MAC logical channel priority for SRB3) . . . . . . 1288
N302 (N302) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1289
N304 (N304) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1290
N308 (N308) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1291
OMSBackupIpAddress (OMS Backup IP Address) . . . . . . . . . . . . . . 1292
OMSIpAddress (OMS IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 1293
PWSMDuration (Duration of low traffic for cell shutdown) . . . . . . . . . 1294
PWSMExceededTrafficDur (Time limit for traffic to activate a shutdown
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1295
PageRep1stInterv (Repetition interval of the first repeated connected
mode paging procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1296
PageRep2ndInterv (Repetition interval of the second repeated connected
mode paging procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1298
RANAPprocInitWait (RANAP initiation timer). . . . . . . . . . . . . . . . . . . 1299
RNCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 1300
RNCIPAddress (RNC IP-address) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1302
RNCName (RNC name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1303
RTservicesForPS (PS domain RT service) . . . . . . . . . . . . . . . . . . . . 1304
RestrictionInterval (Restriction Interval) . . . . . . . . . . . . . . . . . . . . . . . 1305
RncClientTLSMode (RNC Client TLS Mode). . . . . . . . . . . . . . . . . . . 1306
RncId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1307
RncOptions (RNC Options) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1308
SIB11_priority (Priority for SIB11) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1315
SIB15_priority (Priority for SIB15) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1316
SIB18_priority (Priority for SIB18) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1317
SIB19Priority (Priority for SIB19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1318
SIB1_priority (Priority for SIB1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1319
SIB2_priority (Priority for SIB2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1320
SIB3_priority (Priority for SIB3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1321
SIB5_priority (Priority for SIB5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1322
SecOMSIpAddress (Secondary OMS IP address) . . . . . . . . . . . . . . 1323
ServingOMS (Serving OMS ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1324
ServingOMSAdminSetting (Serving OMS Admin Setting) . . . . . . . . . 1326
Id:0900d805809d7397
41
WCDMA Radio Network Configuration Parameters
31.50
31.51
31.52
31.53
31.54
31.55
31.56
31.57
31.58
31.59
31.60
31.61
31.62
31.63
31.64
31.65
31.66
31.67
31.68
31.69
31.70
31.71
31.72
31.73
31.74
31.75
31.76
31.77
31.78
31.79
31.80
31.81
31.82
42
ServingOMSSwoRequest (Serving OMS Switchover Request) . . . . . 1327
T302 (T302) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1329
T304 (T304) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1330
T305 (T305) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1331
T307 (T307) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1332
T308 (T308) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1333
T309 (T309) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1335
T314 (T314) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1335
T316 (T316) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1337
T317 (T317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1338
ToAWE_NRT_DCH_tti10 (Time of Arrival Window Endpoint for NRT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1339
ToAWE_NRT_DCH_tti20 (Time of Arrival Window Endpoint for NRT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1340
ToAWE_NRT_DCH_tti40 (Time of Arrival Window Endpoint for NRT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1341
ToAWE_RT_DCH_tti10 (Time of Arrival Window Endpoint for RT DCH (TTI
10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1343
ToAWE_RT_DCH_tti20 (Time of Arrival Window Endpoint for RT DCH (TTI
20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1344
ToAWE_RT_DCH_tti40 (Time of Arrival Window Endpoint for RT DCH (TTI
40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1345
ToAWE_Speech (Time of Arrival Window Endpoint for speech services) .
1346
ToAWS_NRT_DCH_tti10 (Time of Arrival Window Startpoint for NRT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1347
ToAWS_NRT_DCH_tti20 (Time of Arrival Window Startpoint for NRT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1348
ToAWS_NRT_DCH_tti40 (Time of Arrival Window Startpoint for NRT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1349
ToAWS_RT_DCH_tti10 (Time of Arrival Window Startpoint for RT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1350
ToAWS_RT_DCH_tti20 (Time of Arrival Window Startpoint for RT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1351
ToAWS_RT_DCH_tti40 (Time of Arrival Window Startpoint for RT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1352
ToAWS_Speech (Time of Arrival Window Startpoint for speech services).
1353
TraceLCSHorizAccur (Trace LCS Horizontal Accuracy). . . . . . . . . . . 1354
TraceLCSPriority (Trace LCS Priority) . . . . . . . . . . . . . . . . . . . . . . . . 1355
TraceLCSVertAccur (Trace LCS Vertical Accuracy). . . . . . . . . . . . . . 1356
TraceLCSWaitPeriod (Trace LCS Wait Period) . . . . . . . . . . . . . . . . . 1357
ULBLERConfInterval (Uplink measured BLER confidence interval) . . 1358
UL_DLcapacityReqWait (Waiting time for UL/DL capacity request) . . 1359
UePeriodicMeasCpuLimit (UE Periodic Measurement Report CPU Limit) .
1361
UePeriodicMeasInterval (UE Periodic Measurement Report Measurements Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1362
WCELIdleAlarmTimeout (WCEL Idle Alarm Timeout) . . . . . . . . . . . . 1363
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
32
32.1
32.2
32.3
32.4
32.5
32.6
32.7
32.8
32.9
32.10
32.11
32.12
32.13
32.14
32.15
32.16
32.17
32.18
32.19
32.20
32.21
32.22
32.23
32.24
32.25
32.26
32.27
32.28
32.29
32.30
32.31
32.32
32.33
32.34
32.35
32.36
32.37
DN00211177
Issue 12B
RNFC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1365
AMRWithEDCH (Usage of AMR service with E-DCH). . . . . . . . . . . . 1365
AMRWithHSDSCH (Usage of AMR service with HS-DSCH). . . . . . . 1366
AutoACResEnabled (Automatic Access Class Restriction Enabled). 1368
AutomDLPlanUpdEnabled (Automatic DL Plan update enabled) . . . 1370
CCCHforCUCallowed (Usage of CCCH for Cell/URA Update Confirm allowed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1371
CMmasterSwitch (Compressed mode master switch) . . . . . . . . . . . . 1372
CSFBEnabled (CSFB Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1373
CUCforPCHtoDCHallowed (Direct State Transition From Cell_PCH to
Cell_DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1374
CVUserInactInSignConnRel (Cause value usage in NAS signaling connection release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1375
CapaSmartphoneEnabled (Capacity Increase for Smartphones Enabled)
1377
DCH00SuppOnIurEnabled (DCH 0/0 Support On Iur Enabled). . . . . 1378
DCHBitRateBalancing (DCH bit rate balancing on/off switch) . . . . . . 1379
DCHScheOverIur (DCH Scheduling Over Iur) . . . . . . . . . . . . . . . . . . 1380
DCHtoPCHEnabled (Enabling direct Cell_DCH to PCH state transition) .
1380
DLOptimisationUsage (Dynamic link optimisation usage) . . . . . . . . . 1381
DynUsageHSDPAReturnChannel (Dynamic usage of UL NRT DCH HSDPA return Channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1383
EUTRAdetection (E-UTRA detection) . . . . . . . . . . . . . . . . . . . . . . . . 1384
EmergencyCallISHOSupport (Emergency Call lSHO Support) . . . . . 1385
EmergencyCallRedirect (Emergency Call Redirect) . . . . . . . . . . . . . 1386
FRLCEnabled (Flexible RLC Enabled) . . . . . . . . . . . . . . . . . . . . . . . 1387
FastDormancyEnabled (Fast Dormancy activation / de-activation parameter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1388
FastPCHSwitchEnabled (Enabling Fast Cell_PCH Switching feature)1389
FasterOLPCEnabled (Faster OLPC Enabled) . . . . . . . . . . . . . . . . . . 1391
FemtoHandoverControl (Femto Handover Control). . . . . . . . . . . . . . 1392
FlexULRLCEnabled (Flexible UL RLC Enabled) . . . . . . . . . . . . . . . . 1393
FlexUpgrUsage (Usage of the Flexible Upgrade of the NRT DCH data rate)
1394
HLSModeSelection (Higher Layer Scheduling mode selection) . . . . 1396
HSDPA16KBPSReturnChannel (HSDPA 16 kbps UL DCH return channel
on/off switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1397
HSDPA48UsersEnabled (HSDPA 48 users enabled) . . . . . . . . . . . . 1398
HSDPADynamicResourceAllocation (HSDPA Dynamic Resource Allocation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400
HSDPAMobility (Serving HS-DSCH cell change and SHO on/off switch) .
1401
HSPAInterRNCMobility (HSPA Inter-RNC Mobility) . . . . . . . . . . . . . 1402
HSPAOverIurExt (HSPA Over Iur Extension) . . . . . . . . . . . . . . . . . . 1404
HSUPADynBLEREnabled (HSUPA Dynamic BLER Enabled) . . . . . 1405
IFHOOverIurExt (IFHO Over Iur Extension) . . . . . . . . . . . . . . . . . . . 1406
ISHOCancellation (Inter-System Handover Cancellation) . . . . . . . . . 1407
ISHOInIurMobility (ISHO In Iur Mobility) . . . . . . . . . . . . . . . . . . . . . . 1408
Id:0900d805809d7397
43
WCDMA Radio Network Configuration Parameters
32.38
32.57
32.58
IntelligentEmergencyCallISHOSupport (Intelligent Emergency Call ISHO
Support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1409
IuPSrelWait3G2GMultiServ (Time supervision for releasing Iu-PS connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410
LFDProfEnabled (LFD profiling Enabled) . . . . . . . . . . . . . . . . . . . . . . 1412
MIBPLMNIdIncluded (MIB PLMN Identity Included) . . . . . . . . . . . . . . 1412
MOCNenabled (Multi-Operator Core Network enabled) . . . . . . . . . . . 1414
PBSpolicy (Priority based scheduling policy) . . . . . . . . . . . . . . . . . . . 1415
PPACEnabled (Paging Permission With Access Control Enabled) . . 1417
PSOpThroUsage (Throughput based optimisation of the PS algorithm usage). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1419
PTTEnabled (Push to talk enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 1421
PWSMDriftAllowed (Cell shutdown allowed with drifting UE) . . . . . . . 1423
PostVerifPeriodDLSynch (Post-verification period in downlink synchronization) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1424
PowerBalancing (Power Balancing on/off) . . . . . . . . . . . . . . . . . . . . . 1425
RABDRAEnabled (Usage of the direct resource allocation for PS NRT HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1427
RNFCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 1429
RNFCId (RNFC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1430
RRCSetupCCHEnabledR99 (RRC setup on CCH enabled for R99 UE) . .
1431
SLHOCmAllowedNRT (CM allowed for NRT connection in SLHO) . . 1433
SRVCCEnabled (SRVCC Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 1433
SignConnActivitySupervision (Activity supervision for NAS signaling connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1435
WPSCallRestriction (Restricting overloaded WPS calls) . . . . . . . . . . 1437
WireLessPriorityService (Usage of the Wireless Priority Service) . . . 1439
33
33.1
33.2
33.3
33.4
33.5
33.6
33.7
33.8
33.9
33.10
33.11
33.12
33.13
33.14
33.15
33.16
33.17
33.18
33.19
RNHSPA Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1441
AARConfigTable (Application Aware RAN Configuration Table) . . . . 1441
AppGrpId (Application Group Identifier) . . . . . . . . . . . . . . . . . . . . . . . 1442
DSCPCode1 (DSCP Code1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1443
DSCPCode2 (DSCP Code2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1445
DSCPCode3 (DSCP Code3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1446
DSCPCode4 (DSCP Code4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1448
DSCPCode5 (DSCP Code5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1449
Precedence (Precedence) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1450
TargetSPIforSPI0 (Target SPI for SPI 0) . . . . . . . . . . . . . . . . . . . . . . 1451
TargetSPIforSPI1 (Target SPI for SPI 1) . . . . . . . . . . . . . . . . . . . . . . 1453
TargetSPIforSPI10 (Target SPI for SPI 10) . . . . . . . . . . . . . . . . . . . . 1455
TargetSPIforSPI11 (Target SPI for SPI 11) . . . . . . . . . . . . . . . . . . . . 1456
TargetSPIforSPI2 (Target SPI for SPI 2 ) . . . . . . . . . . . . . . . . . . . . . . 1458
TargetSPIforSPI3 (Target SPI for SPI 3 ) . . . . . . . . . . . . . . . . . . . . . . 1460
TargetSPIforSPI4 (Target SPI for SPI 4) . . . . . . . . . . . . . . . . . . . . . . 1461
TargetSPIforSPI5 (Target SPI for SPI 5) . . . . . . . . . . . . . . . . . . . . . . 1463
TargetSPIforSPI6 (Target SPI for SPI 6) . . . . . . . . . . . . . . . . . . . . . . 1465
TargetSPIforSPI7 (Target SPI for SPI 7) . . . . . . . . . . . . . . . . . . . . . . 1466
TargetSPIforSPI8 (Target SPI for SPI 8) . . . . . . . . . . . . . . . . . . . . . . 1468
32.39
32.40
32.41
32.42
32.43
32.44
32.45
32.46
32.47
32.48
32.49
32.50
32.51
32.52
32.53
32.54
32.55
32.56
44
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
33.20
33.21
33.22
33.23
33.24
33.25
33.26
33.27
33.28
33.29
33.30
33.31
33.32
33.33
33.34
33.35
33.36
33.37
33.38
33.39
33.40
33.41
33.42
33.43
33.44
33.45
33.46
33.47
33.48
33.49
33.50
33.51
33.52
33.53
33.54
33.55
33.56
33.57
33.58
DN00211177
Issue 12B
TargetSPIforSPI9 (Target SPI for SPI 9) . . . . . . . . . . . . . . . . . . . . . . 1470
ARPWeight (ARP based weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1471
WeightForARP1 (Weight for ARP1). . . . . . . . . . . . . . . . . . . . . . . . . . 1473
WeightForARP2 (Weight for ARP2). . . . . . . . . . . . . . . . . . . . . . . . . . 1474
WeightForARP3 (Weight for ARP3). . . . . . . . . . . . . . . . . . . . . . . . . . 1475
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA) . . 1476
CPCNRT10msTTI (CPC NRT 10 ms TTI) . . . . . . . . . . . . . . . . . . . . . 1477
N10msCPCOptObjective (CPC Optimization objective NRT 10ms TTI) . .
1478
N10msCQIDTXTimer (CQI DTX Timer NRT 10ms TTI) . . . . . . . . . . 1479
N10msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 10ms TTI)
1481
N10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle NRT
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1482
N10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 NRT
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1483
N10msMACDTXCycle (MAC DTX Cycle NRT 10ms TTI) . . . . . . . . . 1485
N10msMACInacThr (MAC Inactivity Threshold NRT 10ms TTI) . . . . 1486
N10msUEDPCCHburst1 (UE DPCCH burst1 NRT 10ms TTI) . . . . . 1487
N10msUEDPCCHburst2 (UE DPCCH burst2 NRT 10ms TTI) . . . . . 1488
N10msUEDRXCycle (UE DRX Cycle NRT 10ms TTI) . . . . . . . . . . . 1489
N10msUEDTXCycle1 (UE DTX Cycle 1 NRT 10ms TTI) . . . . . . . . . 1490
N10msUEDTXCycle2 (UE DTX Cycle 2 NRT 10ms TTI) . . . . . . . . . 1492
N10msUEDTXLongPreamble (UE DTX Long Preamble N10ms) . . . 1493
CPCNRT2msTTI (CPC NRT 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . 1494
N2msCPCOptObjective (CPC Optimization objective NRT 2ms TTI) 1495
N2msCQIDTXTimer (CQI DTX Timer NRT 2ms TTI) . . . . . . . . . . . . 1496
N2msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 2ms TTI). .
1498
N2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle NRT
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1499
N2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 NRT
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1501
N2msMACDTXCycle (MAC DTX Cycle NRT 2ms TTI) . . . . . . . . . . . 1502
N2msMACInacThr (MAC Inactivity Threshold NRT 2ms TTI) . . . . . . 1503
N2msUEDPCCHburst1 (UE DPCCH burst1 NRT 2ms TTI) . . . . . . . 1505
N2msUEDPCCHburst2 (UE DPCCH burst2 NRT 2ms TTI) . . . . . . . 1506
N2msUEDRXCycle (UE DRX Cycle NRT 2ms TTI) . . . . . . . . . . . . . 1507
N2msUEDTXCycle1 (UE DTX Cycle 1 NRT 2ms TTI) . . . . . . . . . . . 1508
N2msUEDTXCycle2 (UE DTX Cycle 2 NRT 2ms TTI) . . . . . . . . . . . 1509
N2msUEDTXLongPreamble (UE DTX Long Preamble NRT 2ms TTI) . . .
1511
CPCStreaming10msTTI (CPC Streaming 10 ms TTI) . . . . . . . . . . . . 1512
S10msCPCOptObjective (CPC Optimization objective Str 10ms TTI) 1513
S10msCQIDTXTimer (CQI DTX Timer Str 10ms TTI) . . . . . . . . . . . . 1514
S10msCQIFeedbackCPC (CQI Feedback Cycle for CPC Str 10ms TTI) .
1516
S10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Str
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1517
Id:0900d805809d7397
45
WCDMA Radio Network Configuration Parameters
33.59
33.60
33.61
33.62
33.63
33.64
33.65
33.66
33.67
33.68
33.69
33.70
33.71
33.72
33.73
33.74
33.75
33.76
33.77
33.78
33.79
33.80
33.81
33.82
33.83
33.84
33.85
33.86
33.87
33.88
33.89
33.90
33.91
33.92
33.93
33.94
33.95
33.96
33.97
33.98
46
S10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Str
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1518
S10msMACDTXCycle (MAC DTX Cycle Str 10ms TTI) . . . . . . . . . . . 1520
S10msMACInacThr (MAC Inactivity Threshold Str 10ms TTI) . . . . . . 1521
S10msUEDPCCHburst1 (UE DPCCH burst1 Str 10ms TTI) . . . . . . . 1522
S10msUEDPCCHburst2 (UE DPCCH burst2 Str 10ms TTI) . . . . . . . 1523
S10msUEDRXCycle (UE DRX Cycle Str 10ms TTI) . . . . . . . . . . . . . 1524
S10msUEDTXCycle1 (UE DTX Cycle 1 Str 10ms TTI) . . . . . . . . . . . 1525
S10msUEDTXCycle2 (UE DTX Cycle 2 Str 10ms TTI) . . . . . . . . . . . 1527
S10msUEDTXLongPreamble (UE DTX Long Preamble Str 10ms TTI) . . .
1528
CPCStreaming2msTTI (CPC Streaming 2 ms TTI) . . . . . . . . . . . . . . 1529
S2msCPCOptObjective (CPC Optimization objective Str 2ms TTI) . . 1530
S2msCQIDTXTimer (CQI DTX Timer Str 2ms TTI) . . . . . . . . . . . . . . 1531
S2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Str 2ms TTI)1533
S2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Str
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1534
S2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Str
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1535
S2msMACDTXCycle (MAC DTX Cycle Str 2ms TTI) . . . . . . . . . . . . . 1537
S2msMACInacThr (MAC Inactivity Threshold Str 2ms TTI) . . . . . . . . 1538
S2msUEDPCCHburst1 (UE DPCCH burst1 Str 2ms TTI) . . . . . . . . . 1539
S2msUEDPCCHburst2 (UE DPCCH burst2 Str 2ms TTI) . . . . . . . . . 1540
S2msUEDRXCycle (UE DRX Cycle Str 2ms TTI) . . . . . . . . . . . . . . . 1541
S2msUEDTXCycle1 (UE DTX Cycle 1 Str 2ms TTI) . . . . . . . . . . . . . 1542
S2msUEDTXCycle2 (UE DTX Cycle 2 Str 2ms TTI) . . . . . . . . . . . . . 1544
S2msUEDTXLongPreamble (UE DTX Long Preamble Str 2ms TTI) . 1545
CPCVoice10msTTI (CPC Voice 10 ms TTI) . . . . . . . . . . . . . . . . . . . . 1546
V10msCPCOptObjective (CPC Optimization objective Voi 10ms TTI)1548
V10msCQIDTXTimer (CQI DTX Timer Voi 10ms TTI) . . . . . . . . . . . . 1549
V10msCQIFeedbackCPC (CQI Feedback Cycle for CPC Voi 10ms TTI) .
1550
V10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Voi
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1552
V10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Voi
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1553
V10msMACDTXCycle (MAC DTX Cycle Voi 10ms TTI). . . . . . . . . . . 1554
V10msMACInacThr (MAC Inactivity Threshold Voi 10ms TTI) . . . . . . 1555
V10msUEDPCCHburst1 (UE DPCCH burst1 Voi 10ms TTI) . . . . . . . 1557
V10msUEDPCCHburst2 (UE DPCCH burst2 Voi 10ms TTI) . . . . . . . 1558
V10msUEDRXCycle (UE DRX Cycle Voi 10ms TTI) . . . . . . . . . . . . . 1559
V10msUEDTXCycle1 (UE DTX Cycle 1 Voi 10ms TTI) . . . . . . . . . . . 1560
V10msUEDTXCycle2 (UE DTX Cycle 2 Voi 10ms TTI) . . . . . . . . . . . 1561
V10msUEDTXLongPreamble (UE DTX Long Preamble Voi 10ms TTI). . .
1562
CPCVoice2msTTI (CPC Voice 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . 1563
V2msCPCOptObjective (CPC Optimization objective Voi 2ms TTI) . . 1565
V2msCQIDTXTimer (CQI DTX Timer Voi 2ms TTI) . . . . . . . . . . . . . . 1566
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
33.99
33.100
33.101
33.102
33.103
33.104
33.105
33.106
33.107
33.108
33.109
33.110
33.111
33.112
33.113
33.114
33.115
33.116
33.117
33.118
33.119
33.120
33.121
33.122
33.123
33.124
33.125
33.126
33.127
33.128
33.129
33.130
DN00211177
Issue 12B
V2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Voi 2ms TTI) . . .
1567
V2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Voi
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1568
V2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Voi
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1570
V2msMACDTXCycle (MAC DTX Cycle Voi 2ms TTI) . . . . . . . . . . . . 1571
V2msMACInacThr (MAC Inactivity Threshold Voi 2ms TTI) . . . . . . . 1572
V2msUEDPCCHburst1 (UE DPCCH burst1 Voi 2ms TTI) . . . . . . . . 1574
V2msUEDPCCHburst2 (UE DPCCH burst2 Voi 2ms TTI) . . . . . . . . 1575
V2msUEDRXCycle (UE DRX Cycle Voi 2ms TTI). . . . . . . . . . . . . . . 1576
V2msUEDTXCycle1 (UE DTX Cycle 1 Voi 2ms TTI). . . . . . . . . . . . . 1577
V2msUEDTXCycle2 (UE DTX Cycle 2 Voi 2ms TTI). . . . . . . . . . . . . 1578
V2msUEDTXLongPreamble (UE DTX Long Preamble Voi 2ms TTI) 1580
CPICHECNOSRBHSPA (CPICH EcNo for SRB on HSPA) . . . . . . . 1581
CPICHECNOThreEDCH2MS (CPICH ECNO Threshold for E-DCH TTI 2
ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1582
CPICHRSCPThreEDCH2MS (CPICH RSCP Threshold for E-DCH TTI 2
ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1583
CPICHRSCPThreSRBHSDPA (CPICH RSCP Threshold for SRBs on HSDPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1584
DCellVsMIMOPreference (Dual Cell versus MIMO preference) . . . . 1584
DiscardTimerHSCSVoice (HSDPA Discard Timer for the CS voice service)
1586
DiscardTimerPTT (HSDPA Discard Timer for the PTT). . . . . . . . . . . 1587
EDCHCTSwitchGuardTimer (E-DCH channel type switch guard timer) . .
1588
EDCHMACdflowtputStrTtT (Low throughput time to trigger for streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1589
EDCHMaxHARQReTxStr (E-DCH max number of HARQ retransmissions
for streaming). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1591
EDCHMaxHarqReTxSRB (E-DCH maximum # of HARQ retransmissions
for 10 ms SRB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1592
EDCHMaxHarqReTxSRB2MS (E-DCH maximum # of HARQ retransmissions for 2 ms SRB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1593
EDCHMaxNumberOfHARQReTx (E-DCH maximum number of HARQ retransmissions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1594
EDCHQOSClasses (E-DCH QoS classes) . . . . . . . . . . . . . . . . . . . . 1595
EnablDelayHHO (Enabling Delay HHO) . . . . . . . . . . . . . . . . . . . . . . 1596
EnablDelayStand (Enabling Delay Standard) . . . . . . . . . . . . . . . . . . 1597
FDPCHAllocMinInterval (Minimum interval between F-DPCH allocations)
1598
FDPCHAndSRBOnHSPATC (F-DPCH and SRBs on HSPA per TC) 1600
FDPCHSetupEC (DCH instead of F-DPCH based on Establishment
Cause) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1601
FactorEDCHMaxBRPSstream (Factor E-DCH max. Bit Rate for PS
streaming RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1603
FactorEDCHMaxBitRate (Factor to calculate EDCH maximum bit rate) . .
1605
Id:0900d805809d7397
47
WCDMA Radio Network Configuration Parameters
33.131
33.132
33.133
33.134
33.135
33.136
33.137
33.138
33.139
33.140
33.141
33.142
33.143
33.144
33.145
33.146
33.147
33.148
33.149
33.150
33.151
33.152
33.153
33.154
33.155
33.156
33.157
33.158
33.159
33.160
33.161
33.162
33.163
33.164
33.165
33.166
33.167
33.168
48
FactorEDCHMaxBitRate2NRT (Factor E-DCH max. Bit Rate for 2 NRT
RAB combinations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1606
FactorEDCHMaxBitRate3NRT (Factor E-DCH max. Bit Rate for 3 NRT
RAB combinations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1607
HSDPACPICHCTSRepPer (DCH to HS-DSCH switch CPICH Ec/No reporting period) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1608
HSDPACPICHEcNoThreshold (CPICH Ec/No threshold for serving HSDSCH cell change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1609
HSDPACellChangeRepetitionTime (Window for max repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1610
HSDPAChaTypeSwitchWindow (HSDPA channel type switching window)
1611
HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1612
HSDPAPeakRateLimitRABMax (HSDPA peak rate limitation to the RAB
maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1614
HSDPAPriority (HSDPA priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1615
HSDPARRCdiversity (SHO of the HSDPA capable UE) . . . . . . . . . . 1617
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1618
HSDSCHCTSwitchGuardTimer (HS-DSCH channel type switch guard timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1620
HSDSCHGuardTimerLowThroughput (HS-DSCH guard timer due to low
throughput) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1621
HSDSCHQoSclasses (HS-DSCH QoS classes). . . . . . . . . . . . . . . . . 1622
HSPANBRValues (HSPA NBR values) . . . . . . . . . . . . . . . . . . . . . . . 1623
NBRForPri0DL (Downlink NBR for Priority value 0) . . . . . . . . . . . . . . 1625
NBRForPri0UL (Uplink NBR for Priority value 0) . . . . . . . . . . . . . . . . 1626
NBRForPri10DL (Downlink NBR for Priority value 10) . . . . . . . . . . . . 1627
NBRForPri10UL (Uplink NBR for Priority value 10) . . . . . . . . . . . . . . 1628
NBRForPri11DL (Downlink NBR for Priority value 11) . . . . . . . . . . . . 1629
NBRForPri11UL (Uplink NBR for Priority value 11) . . . . . . . . . . . . . . 1630
NBRForPri12DL (Downlink NBR for Priority value 12) . . . . . . . . . . . . 1631
NBRForPri12UL (Uplink NBR for Priority value 12) . . . . . . . . . . . . . . 1632
NBRForPri1DL (Downlink NBR for Priority value 1) . . . . . . . . . . . . . . 1633
NBRForPri1UL (Uplink NBR for Priority value 1) . . . . . . . . . . . . . . . . 1635
NBRForPri2DL (Downlink NBR for Priority value 2) . . . . . . . . . . . . . . 1636
NBRForPri2UL (Uplink NBR for Priority value 2) . . . . . . . . . . . . . . . . 1637
NBRForPri3DL (Downlink NBR for Priority value 3) . . . . . . . . . . . . . . 1638
NBRForPri3UL (Uplink NBR for Priority value 3) . . . . . . . . . . . . . . . . 1639
NBRForPri4DL (Downlink NBR for Priority value 4) . . . . . . . . . . . . . . 1640
NBRForPri4UL (Uplink NBR for Priority value 4) . . . . . . . . . . . . . . . . 1641
NBRForPri5DL (Downlink NBR for Priority value 5) . . . . . . . . . . . . . . 1642
NBRForPri5UL (Uplink NBR for Priority value 5) . . . . . . . . . . . . . . . . 1643
NBRForPri6DL (Downlink NBR for Priority value 6) . . . . . . . . . . . . . . 1644
NBRForPri6UL (Uplink NBR for Priority value 6) . . . . . . . . . . . . . . . . 1645
NBRForPri7DL (Downlink NBR for Priority value 7) . . . . . . . . . . . . . . 1646
NBRForPri7UL (Uplink NBR for Priority value 7) . . . . . . . . . . . . . . . . 1647
NBRForPri8DL (Downlink NBR for Priority value 8) . . . . . . . . . . . . . . 1648
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
33.169
33.170
33.171
33.172
33.173
33.174
33.175
33.176
33.177
33.178
33.179
33.180
33.181
33.182
33.183
33.184
33.185
33.186
33.187
33.188
33.189
33.190
33.191
33.192
33.193
33.194
33.195
33.196
33.197
DN00211177
Issue 12B
NBRForPri8UL (Uplink NBR for Priority value 8) . . . . . . . . . . . . . . . . 1649
NBRForPri9DL (Downlink NBR for Priority value 9) . . . . . . . . . . . . . 1650
NBRForPri9UL (Uplink NBR for Priority value 9) . . . . . . . . . . . . . . . . 1651
HSPDSCHAdjustPeriod (HS-PDSCH code adjustment period) . . . . 1652
HappyBitDelayConditionEDCH (Happy bit delay condition for E-DCH). . .
1653
HsdschGuardTimerHO (HS-DSCH guard time after switching to DCH due
to HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1654
InacUserNbrXXXOverNRT (Inactive users number in XXX over NRT) . . .
1655
InacUsersOverloadFact (Inactive users overload preventive factor) . 1656
InitialSPINRT (Initial SPI for PS NRT RAB) . . . . . . . . . . . . . . . . . . . . 1658
MACdflowthroughputRelThr (Low throughput threshold of the MAC-d flow)
1660
MACdflowthroughputTimetoTrigger (Low throughput time to trigger of the
MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1661
MACdflowtputStrTtT (Low throughput time to trigger of streaming MAC-d
flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1662
MACdflowutilStrTtT (Low util time to trigger of MAC-d flow for streaming)
1663
MEHCQIFeedbackCycle (Temporary CQI feedback cycle for the Mass
Event Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1665
MEHHSUPAUserIncr (HSUPA user increment for the Mass Event Handler)
1666
MaxBitRateNRTMACDFlow (Maximum bit rate of NRT MAC-d flow) 1668
MaxCSDelayRNCETTI10 (Max buffer time of the HS CS voice in RNC ETTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1670
MaxCSDelayRNCETTI2 (Max buffer time of the HS CS voice in RNC E-TTI
2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1672
MaxCSDelayUE (Max buffer time of the HS CS voice in UE) . . . . . . 1674
MaxEHARQReTxCSAMR10 (E-DCH max number of retransmissions CS
voice E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1675
MaxEHARQReTxCSAMR2 (E-DCH max number of retransmissions CS
voice E-TTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1676
MaxEHARQReTxPSconv10 (E-DCH max number of retransmissions PS
conv E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1677
MaxEHARQReTxPSconv2 (E-DCH max number of retransmissions PS
conv E-TTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1678
MaxReWaitTime (Maximum Reordering Wait Time for MAC-es) . . . 1679
MaxReWaitTime2msTTI (Maximum Reordering Wait Time for Mac-es EDCH 2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1680
MaxReWaitTime2msTTI16 (Maximum reordering wait time parameter for
MAC-es E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1681
MaxReWaitTimeRT (Maximum MAC-es Reordering Wait time for RT user)
1682
MaxSetOfEDPDCHCSAMR10 (Maximum Set of E-DPDCHs for CS voice
E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1683
MaxSetOfEDPDCHCSAMR2 (Maximum Set of E-DPDCHs for CS voice ETTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1684
Id:0900d805809d7397
49
WCDMA Radio Network Configuration Parameters
33.198
33.220
33.221
33.222
33.223
33.224
33.225
33.226
33.227
33.228
33.229
NRTRBBRWithEDCHStr (NRT RB user bit rate with E-DCH streaming) . .
1685
PTTRLCPDUSizeHSDSCH (RLC PDU size for PTT mapped to HS-DSCH)
1687
PeriodicityForSI (Periodicity for scheduling info) . . . . . . . . . . . . . . . . 1688
PowerOffsetEHARQPSConv (HARQ power offset for E-DCH MAC-d flow
of PS conv) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1689
PowerOffsetEHARQVoice (HARQ power offset for E-DCH MAC-d flow of
CS voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1690
PowerOffsetForSI (Power Offset for Scheduling Info) . . . . . . . . . . . . 1691
RNHSPAChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 1692
RNHSPAId (RNHSPA Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1693
SmartHSPATimeToTrigger (Time-to-trigger for Smartphone throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1694
SmartHSPATputAveWin (Window size for Smartphone throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1695
T1HSCSVoice (HSDPA re-ordering release timer T1 for the CS voice) . . .
1696
T1HSFACH (HSDPA re-ordering release timer T1 for xCCH on HS-FACH)
1698
T1PTT (HSDPA re-ordering rel timer T1 for the PTT) . . . . . . . . . . . . 1699
TGPLAMRHSDPAInterFreq (TGPL for AMR and HSDPA and IF measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1701
TGPLHSDPAInterFreq (TGPL for HSDPA and IF measurement) . . . 1702
ThresholdMaxEDPDCHSR (Threshold to define maximum E-DPDCH SR)
1703
ThresholdMaxEDPDCHSR1920kbps (Threshold to define maximum EDPDCH SR 1920 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1704
ThresholdMaxEDPDCHSR3840kbps (Threshold to define maximum EDPDCH SR 3840 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1706
ThresholdMaxEDPDCHSR960kbps (Threshold to define maximum EDPDCH SR 960 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1707
UPResAllocInCellDCHWait (Retry time for u-plane resource allocation in
Cell_DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1708
VCPHSDPAPrevDuration (Duration of HSDPA prevention for Voice Call
Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1710
VCPHSDPAUserIncr (HSDPA user increment for the Voice Call Priority) .
1711
WeightDCH (Weight of NRT DCH UE) . . . . . . . . . . . . . . . . . . . . . . . . 1713
WeightDCHBG (Weight of NRT DCH UE BG RAB) . . . . . . . . . . . . . . 1714
WeightDCHTHP1 (Weight of NRT DCH UE THP1 RAB) . . . . . . . . . . 1715
WeightDCHTHP2 (Weight of NRT DCH UE THP2 RAB) . . . . . . . . . . 1716
WeightDCHTHP3 (Weight of NRT DCH UE THP3 RAB) . . . . . . . . . . 1717
WeightHSPA (Weight of HSPA UE) . . . . . . . . . . . . . . . . . . . . . . . . . . 1718
WeightHSPABG (Weight of HSPA UE BG RAB) . . . . . . . . . . . . . . . . 1720
WeightHSPATHP1 (Weight of HSPA UE THP1 RAB) . . . . . . . . . . . . 1721
WeightHSPATHP2 (Weight of HSPA UE THP2 RAB) . . . . . . . . . . . . 1722
WeightHSPATHP3 (Weight of HSPA UE THP3 RAB) . . . . . . . . . . . . 1723
34
RNMOBI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1725
33.199
33.200
33.201
33.202
33.203
33.204
33.205
33.206
33.207
33.208
33.209
33.210
33.211
33.212
33.213
33.214
33.215
33.216
33.217
33.218
33.219
50
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
34.1
34.2
34.3
34.4
34.5
34.6
34.7
34.8
34.9
34.10
34.11
34.12
34.13
34.14
34.15
34.16
34.17
34.18
34.19
34.20
34.21
34.22
34.23
34.24
34.25
34.26
34.27
34.28
34.29
34.30
34.31
34.32
34.33
34.34
DN00211177
Issue 12B
AnchorFmciIdentifier (Anchor FMCI Identifier). . . . . . . . . . . . . . . . . . 1725
AnchorFmcsIdentifier (Anchor FMCS Identifier) . . . . . . . . . . . . . . . . 1726
AnchorHopiIdentifier (Anchor HOPI Identifier) . . . . . . . . . . . . . . . . . . 1726
AnchorHopsIdentifier (Anchor HOPS Identifier). . . . . . . . . . . . . . . . . 1727
CellReselectionObservingTime (Cell Reselection Observing Time) . 1728
DRRCForHSDPALayerServices (Services for DRRC connection setup for
HSDPA layer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1730
DefaultAuthorisedNetworkId (Identifier of the Default Authorised Network)
1731
DirectedRRCForHSDPALayerEnhanc (DRRC connection setup for HSDPA layer enhancements) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1732
DisablePowerInHSDPALayeringDecision (Disable power in decision making for HSDPA layering). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1734
EcnoDifferenceThreshold (CPICH EcNo Difference Threshold) . . . . 1736
EnableULQualDetRep (Quality deterioration report from UL OLPC controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1737
FastDormOverCpcPri (Fast Dormancy and CPC priority) . . . . . . . . . 1738
FastUECancel (Fast UE Cancellation). . . . . . . . . . . . . . . . . . . . . . . . 1739
FastUEPeriod (Fast UE evaluation period) . . . . . . . . . . . . . . . . . . . . 1740
FastUEThreshold (Fast UE Threshold) . . . . . . . . . . . . . . . . . . . . . . . 1741
GANetwARFCN (GAN ARFCN). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1742
GANetwBCC (GAN BCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1743
GANetwNCC (GAN NCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1744
GapPositionSingleFrame (Gap position single frame). . . . . . . . . . . . 1745
GsmHandoverAMR (Handover of AMR Service to GSM) . . . . . . . . . 1746
GsmHandoverCS (Handover of CS Service to GSM) . . . . . . . . . . . . 1748
GsmHandoverNrtPS (Handover of NRT PS Service to GSM). . . . . . 1749
GsmHandoverRtPS (Handover of RT PS Service to GSM). . . . . . . . 1751
HSCAHORabCombSupport (RAB Combinations Supported by HSCAHO)
1752
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1753
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1755
HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1756
HSDPALayerLoadShareThreshold (HSDPA layers load sharing threshold)
1758
HSDPASIRErrorAveWindow (Averaging window of the SIRerror measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1759
HSDPASIRErrorFilterCoefficient (Higher layer filtering coefficient for HSDPA SIRerror) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1760
HSDPASIRErrorReportPeriod (Reporting period of the SIRerror measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1762
HSDPASIRErrorServCell (SIRerror threshold for the serving HS-DSCH
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1763
HSDPASIRErrorTargetCell (SIRerror threshold for the target cell) . . 1764
HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1765
Id:0900d805809d7397
51
WCDMA Radio Network Configuration Parameters
34.35
34.36
34.37
34.38
34.39
34.40
34.41
34.42
34.43
34.44
34.45
34.46
34.47
34.48
34.49
34.50
34.51
34.52
34.53
34.54
34.55
34.56
34.57
34.58
34.59
34.60
34.61
34.62
34.63
34.64
34.65
52
HSPADRNCEcNoOffset (DRNC Ec/No offset for HSPA Inter-RNC Cell
Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1767
HSPADRNCSIRErrorOffset (SIR error offset for HSPA Inter-RNC Cell
Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1768
IBTSRabCombSupport (RAB Combinations Supported by FD-BTS) . 1770
LHOMinNrtDchAllocTime (Load handover minimum NRT DCH allocation
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1771
LowerRxTxTimeDiff (Lower Rx-Tx Time Difference Threshold) . . . . . 1772
MBLBGuardTimer (MBLB Guard Timer). . . . . . . . . . . . . . . . . . . . . . . 1773
MaxCellReselections (Max cell reselections) . . . . . . . . . . . . . . . . . . . 1774
MaxNumISHOClPerAS (Max Number of ISHO Cancellations Per Active
Set for a U) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1776
MultipleBSICIdent (Multiple BSIC Identification) . . . . . . . . . . . . . . . . . 1777
NCHOFilterCoeffComLoadMeasDRNCCell (NCHO filter coefficient common load meas DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1778
NCHOHystComLoadMeasDRNCCell (NCHO hysteresis common load
measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1780
NCHOThrComLoadMeasDRNCCell (NCHO threshold common load measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1781
PreferBandForLayering (Preferred Band for Layering). . . . . . . . . . . . 1782
RANAPCauseLoadHO (RANAP cause to indicate load handover) . . 1783
RANAPCause1LoadHO (RANAP cause 1 to indicate load handover) 1784
RANAPCause2LoadHO (RANAP cause 2 to indicate load handover) 1785
RANAPCause3LoadHO (RANAP cause 3 to indicate load handover) 1786
RANAPCauseServHO (RANAP cause to indicate service handover) 1787
RANAPCause1ServHO (RANAP cause 1 to indicate service handover) . .
1788
RANAPCause2ServHO (RANAP cause 2 to indicate service handover) . .
1789
RANAPCause3ServHO (RANAP cause 3 to indicate service handover) . .
1790
RNMOBIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 1791
RNMOBIId (RNMOBI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1793
SLHOHandlingOfCellLoadMeasNotAct (SLHO handling of cell load measurement is not active) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1794
SLHOProfileBackgroundPSNRTData (Service profile for background PS
NRT data in SLHO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1795
SLHOProfileConvCSSpeech (Service profile for conversational CS speech
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1797
SLHOProfileConvCSTData (Service profile for conversational CS T data in
SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1799
SLHOProfileConvPSRTData (Service profile for conversational PS RT
data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1801
SLHOProfileConvPSSpeech (Service profile for conversational PS speech
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1803
SLHOProfileInteractivePSNRTData (Service profile for interactive PS NRT
data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1805
SLHOProfileStreamCSNTData (Service profile for streaming CS NT data
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1807
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
34.66
34.67
34.68
34.69
34.70
34.71
34.72
34.73
34.74
34.75
34.76
34.77
34.78
34.79
34.80
34.81
34.82
34.83
34.84
34.85
34.86
34.87
34.88
34.89
34.90
34.91
34.92
34.93
DN00211177
Issue 12B
SLHOProfileStreamPSRTData (Service profile for streaming PS RT data in
SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1809
SLHOUseBackgroundPSNRTData (Use of SLHO for background PS NRT
data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1811
SLHOUseConvCSSpeech (Use of SLHO for conversational CS speech).
1813
SLHOUseConvCSTData (Use of SLHO for conversational CS transparent
data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1815
SLHOUseConvPSRTData (Use of SLHO for conversational PS RT data)
1817
SLHOUseConvPSSpeech (Use of SLHO for conversational PS speech) .
1819
SLHOUseInteractivePSNRTData (Use of SLHO for interactive PS NRT data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1821
SLHOUseStreamCSNTData (Use of SLHO for streaming CS non-transparent data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1824
SLHOUseStreamPSRTData (Use of SLHO for streaming PS RT data) . .
1825
ServBtwnHSDPALayers (Services between HSDPA layers). . . . . . . 1827
ServicesToHSDPALayer (Services to HSDPA layer in state transition) . .
1828
SmartLTELayeringPrevT (Timer for Smart LTE Layering Prevention) . . .
1830
SmartLTELayeringServ (Smart LTE Layering service control) . . . . . 1831
TGPLdoubleframeNRTPSgsm (Transmision gap pattern length in case of
double frame: NRT PS service and GSM measurement) . . . . . . . . . 1832
TGPLdoubleframeNRTPSinterFreq (Transmision gap pattern length in
case of double frame: NRT PS service and IF measurement) . . . . . 1833
TGPLsingleframeAMRgsm (Transmision gap pattern length in case of single frame: AMR service and GSM measurement) . . . . . . . . . . . . . . . 1834
TGPLsingleframeAMRinterFreq (Transmision gap pattern length in case of
single frame: AMR service and IF measurement) . . . . . . . . . . . . . . . 1835
TGPLsingleframeCSgsm (Transmision gap pattern length in case of single
frame: CS service and GSM measurement) . . . . . . . . . . . . . . . . . . . 1836
TGPLsingleframeCSinterFreq (Transmision gap pattern length in case of
single frame: CS service and IF measurement). . . . . . . . . . . . . . . . . 1837
TGPLsingleframeNRTPSgsm (Transmision gap pattern length in case of
single frame: NRT PS service and GSM measurement) . . . . . . . . . . 1838
TGPLsingleframeNRTPSinterFreq (Transmision gap pattern length in case
of single frame: NRT PS service and IF measurement) . . . . . . . . . . 1839
TGPLsingleframeRTPSgsm (Transmision gap pattern length in case of
single frame: RT PS service and GSM measurement) . . . . . . . . . . . 1841
TGPLsingleframeRTPSinterFreq (Transmision gap pattern length in case
of single frame: RT PS service and IF measurement) . . . . . . . . . . . . 1842
TRelocOverall (T RelocOverall) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1843
TRelocPrep (T RelocPrep). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1844
UEQualityRepInterv (UE Quality Measurement Reporting Interval) . 1845
UETxPowerMaxRef (Maximum Reference UE transmission power). 1846
ULQualDetRepThreshold (UL quality deterioration reporting threshold) . .
1847
Id:0900d805809d7397
53
WCDMA Radio Network Configuration Parameters
34.94
UpperRxTxTimeDiff (Upper Rx-Tx Time Difference Threshold) . . . . . 1848
35
35.1
35.2
RNPS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1850
ActivationTimeOffset (Offset for activation time). . . . . . . . . . . . . . . . . 1850
CellDCHtestTmr (Test timer for inactivity supervision in Cell_DCH state) .
1851
CrQueuingTimeDL (Maximum downlink capacity request queuing time) . .
1852
CrQueuingTimeUL (Maximum uplink capacity request queuing time) 1854
DCHUtilBelowDowngradeThr (Threshold below the downgrade bit rate). .
1855
DCHUtilHighAveWin (Window size for the high throughput measurement)
1856
DCHUtilHighBelowNRTDataRateThr (Threshold below the NRT DCH data
rate). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1858
DCHUtilHighTimeToTrigger (Time to trigger for the high throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1860
DCHUtilLowerAveWinBitRate (Window size for the lower throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1861
DCHUtilLowerAveWin128 (Lower measurement window size for NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1863
DCHUtilLowerAveWin256 (Lower measurement window size for NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1865
DCHUtilLowerAveWin32 (Lower measurement window size for NRT DCH
of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1867
DCHUtilLowerAveWin384 (Lower measurement window size for NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1869
DCHUtilLowerAveWin64 (Lower measurement window size for NRT DCH
of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1871
DCHUtilLowerDowngradeThrBitRate (Lower downgrade threshold) . 1873
DCHUtilLowerDowngradeThr128 (Lower downgrade threshold for the NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1875
DCHUtilLowerDowngradeThr256 (Lower downgrade threshold for the NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1877
DCHUtilLowerDowngradeThr32 (Lower downgrade threshold for the NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1878
DCHUtilLowerDowngradeThr384 (Lower downgrade threshold for the NRT
DCH of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1879
DCHUtilLowerDowngradeThr64 (Lower downgrade threshold for the NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1880
DCHUtilLowerTimeToTriggerBitRate (Time to trigger for the lower throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1882
DCHUtilLowerTimeToTrigger128 (Lower time to trigger for the NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1884
DCHUtilLowerTimeToTrigger256 (Lower time to trigger for the NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1885
DCHUtilLowerTimeToTrigger32 (Lower time to trigger for the NRT DCH of
32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1886
DCHUtilLowerTimeToTrigger384 (Lower time to trigger for the NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1887
35.3
35.4
35.5
35.6
35.7
35.8
35.9
35.10
35.11
35.12
35.13
35.14
35.15
35.16
35.17
35.18
35.19
35.20
35.21
35.22
35.23
35.24
35.25
54
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
35.26
35.27
35.28
35.29
35.30
35.31
35.32
35.33
35.34
35.35
35.36
35.37
35.38
35.39
35.40
35.41
35.42
35.43
35.44
35.45
35.46
35.47
35.48
35.49
35.50
35.51
35.52
DN00211177
Issue 12B
DCHUtilLowerTimeToTrigger64 (Lower time to trigger for the NRT DCH of
64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1888
DCHUtilMeasGuardTime (Guard time for throughput measurement) 1889
DCHUtilUpperAveWinBitRate (Window size for the upper throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1890
DCHUtilUpperAveWin128 (Upper measurement window size for NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1892
DCHUtilUpperAveWin256 (Upper measurement window size for NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1894
DCHUtilUpperAveWin32 (Upper measurement window size for NRT DCH
of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1896
DCHUtilUpperAveWin384 (Upper measurement window size for NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1898
DCHUtilUpperAveWin64 (Upper measurement window size for NRT DCH
of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900
DCHUtilUpperDowngradeThrBitRate (Upper downgrade threshold). 1902
DCHUtilUpperDowngradeThr128 (Upper downgrade threshold for the NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1904
DCHUtilUpperDowngradeThr256 (Upper downgrade threshold for the NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1906
DCHUtilUpperDowngradeThr32 (Upper downgrade threshold for the NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1907
DCHUtilUpperDowngradeThr384 (Upper downgrade threshold for the NRT
DCH of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1908
DCHUtilUpperDowngradeThr64 (Upper downgrade threshold for the NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1909
DCHUtilUpperTimeToTriggerBitRate (Time to trigger for the upper
throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1910
DCHUtilUpperTimeToTrigger128 (Upper time to trigger for the NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1913
DCHUtilUpperTimeToTrigger256 (Upper time to trigger for the NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1914
DCHUtilUpperTimeToTrigger32 (Upper time to trigger for the NRT DCH of
32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1915
DCHUtilUpperTimeToTrigger384 (Upper time to trigger for the NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1916
DCHUtilUpperTimeToTrigger64 (Upper time to trigger for the NRT DCH of
64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1917
DLOptimisationProhibitTime (Dynamic Link Optimisation prohibit time) . .
1918
DLOptimisationPwrOffset (Power offset for dynamic link optimisation) . . .
1919
FactorMinPBSinterval (Factor to determine minimum PBS interval) . 1920
HSFACHDiscardTimerDTCH (Discard Timer for DTCH data on HS-FACH)
1922
HSFACHRestTimerDTCH (MAC-ehs Reset Timer for DTCH data on HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1923
ICRDowngradeDelayTimer (ICR Downgrade Delay Timer). . . . . . . . 1924
InactDetForStreamingRB (Inactivation detection for streaming radio bearer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1925
Id:0900d805809d7397
55
WCDMA Radio Network Configuration Parameters
35.53
35.54
35.55
35.56
35.57
35.58
35.59
35.60
35.61
35.62
35.63
35.64
35.65
35.66
35.67
35.68
35.69
35.70
35.71
35.72
35.73
35.74
35.75
35.76
35.77
35.78
35.79
35.80
35.81
35.82
35.83
35.84
56
IurPriority (Priority handling over Iur-interface) . . . . . . . . . . . . . . . . . . 1926
MEHTVMPendingTime (Temporary TVM pending time for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1928
PTTDormancyTimer (PTT dormancy timer) . . . . . . . . . . . . . . . . . . . . 1929
QoSPriorityMapping (QoS Priority Mapping) . . . . . . . . . . . . . . . . . . . 1930
PriForBackARP1 (Priority for Background TC with ARP 1) . . . . . . . . 1933
PriForBackARP2 (Priority for Background TC with ARP 2) . . . . . . . . 1935
PriForBackARP3 (Priority for Background TC with ARP 3) . . . . . . . . 1936
PriForConvOnHSPA (Priority for conversational on HSPA) . . . . . . . . 1937
PriForHSFACHDTCH (Priority for PS data over HSPA on CELL_FACH
state.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1938
PriForIntSignaling (Priority for Interactive TC marked for signaling use) . .
1939
PriForIntTHP1ARP1 (Priority for Interactive TC with THP 1 and ARP 1) . .
1941
PriForIntTHP1ARP2 (Priority for Interactive TC with THP 1 and ARP 2) . .
1942
PriForIntTHP1ARP3 (Priority for Interactive TC with THP 1 and ARP 3) . .
1944
PriForIntTHP2ARP1 (Priority for Interactive TC with THP 2 and ARP 1) . .
1945
PriForIntTHP2ARP2 (Priority for Interactive TC with THP 2 and ARP 2) . .
1946
PriForIntTHP2ARP3 (Priority for Interactive TC with THP 2 and ARP 3) . .
1947
PriForIntTHP3ARP1 (Priority for Interactive TC with THP 3 and ARP 1) . .
1949
PriForIntTHP3ARP2 (Priority for Interactive TC with THP 3 and ARP 2) . .
1950
PriForIntTHP3ARP3 (Priority for Interactive TC with THP 3 and ARP 3) . .
1951
PriForSRBsOnHSPA (Priority for SRBs on HSPA). . . . . . . . . . . . . . . 1952
PriForStreamARP1 (Priority for Streaming traffic class with ARP1) . . 1953
PriForStreamARP2 (Priority for Streaming traffic class with ARP2) . . 1955
PriForStreamARP3 (Priority for Streaming traffic class with ARP3) . . 1956
RNPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 1958
RNPSId (RNPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1959
RTOverNRTPriThresholdARP1 (RT-over-NRT priority threshold for ARP1)
1960
RTOverNRTPriThresholdARP2 (RT-over-NRT priority threshold for ARP2)
1961
RTOverNRTPriThresholdARP3 (RT-over-NRT priority threshold for ARP3)
1962
SmartInactTimerFACH (Inactivity Timer for Smart Phones in Cell_FACH)
1964
SmartInactivityTimerDCH (Inactivity timer for Smartphone DCH) . . . 1965
ToCellFACHinTest (Test switch for Iu release in Cell_DCH state) . . . 1966
TrafVolThresholdDLHigh (Downlink traffic volume measurement high
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1967
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
35.85
35.86
35.87
35.88
35.89
35.90
35.91
35.92
35.93
35.94
35.95
35.96
35.97
35.98
35.99
35.100
35.101
35.102
36
36.1
36.2
36.3
36.4
36.5
36.6
36.7
DN00211177
Issue 12B
TrafVolThresholdDLHighBitRate (Traffic volume threshold for downlink
NRT DCH bit rates) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1969
TrafVolThresholdDLHighDCH128 (Traffic volume threshold for DL NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1971
TrafVolThresholdDLHighDCH16 (Traffic volume threshold for DL NRT
DCH of 16 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1973
TrafVolThresholdDLHighDCH256 (Traffic volume threshold for DL NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1975
TrafVolThresholdDLHighDCH32 (Traffic volume threshold for DL NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1977
TrafVolThresholdDLHighDCH64 (Traffic volume threshold for DL NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1979
TrafVolThresholdDLHighDCH8 (Traffic volume threshold for DL NRT DCH
of 8 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1981
TrafVolThresholdULHigh (Uplink traffic volume measurement high threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1983
TrafVolThresholdULHighBitRate (Traffic volume threshold for uplink NRT
DCH bit rates) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1985
TrafVolThresholdULHighDCH128 (Traffic volume threshold for UL NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1987
TrafVolThresholdULHighDCH16 (Traffic volume threshold for UL NRT
DCH of 16 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1989
TrafVolThresholdULHighDCH256 (Traffic volume threshold for UL NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1991
TrafVolThresholdULHighDCH32 (Traffic volume threshold for UL NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1993
TrafVolThresholdULHighDCH64 (Traffic volume threshold for UL NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1995
TrafVolThresholdULHighDCH8 (Traffic volume threshold for UL NRT DCH
of 8 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1997
TrafVolTimeToTriggerDL (Downlink traffic volume measurement time to
trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1999
TrafVolTimeToTriggerUL (Uplink traffic volume measurement time to trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000
ULLoadStateTTT (UL loaded state time to trigger) . . . . . . . . . . . . . . 2002
RNRLC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2004
AMRLCBufMaxOverbook2NRT (AM RLC buffer max total overbooking for
2 PS RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2004
AMRLCBufMaxOverbook3NRT (AM RLC buffer max overbooking for more
than 2 PS RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2005
AMRLCHSFACHPS (AM RLC configuration for PS NRT with HS-FACH)
2006
AMRLCHSFACHPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2007
AMRLCHSFACHPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2008
AMRLCHSFACHPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2010
AMRLCHSFACHPSPeriodMax (AM RLC status period max for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2011
Id:0900d805809d7397
57
WCDMA Radio Network Configuration Parameters
36.8
36.9
36.10
36.11
36.12
36.13
36.14
36.15
36.16
36.17
36.18
36.19
36.20
36.21
36.22
36.23
36.24
36.25
36.26
36.27
36.28
36.29
36.30
36.31
36.32
58
AMRLCHSFACHPSPeriodMin (AM RLC status period min for PS NRT with
HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2012
AMRLCHSFACHPSPollPDU (AM RLC period Poll_PDU for PS NRT with
HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2013
AMRLCHSFACHPSPollSDU (AM RLC period Poll_SDU for PS NRT with
HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2015
AMRLCHSFACHPSPollWin (AM RLC period Poll_Window for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2016
AMRLCHSFACHPSTriggers (AM RLC status report triggers for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2017
AMRLCRespHSFACHandRACH (AM RLC round trip time with HSDSCH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2019
HSFACHAMRLCRespHSRACH (AM RLC round trip time with HSDSCH/HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2020
AMRLCHSRACHPS (AM RLC configuration for PS NRT with HS-RACH).
2022
AMRLCHSRACHPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with HS-RACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2023
AMRLCHSRACHPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with HS-RACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2024
AMRLCHSRACHPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with HS-RACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2025
AMRLCHSRACHPSPeriodMax (AM RLC status period max for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2026
AMRLCHSRACHPSPeriodMin (AM RLC status period min for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2028
AMRLCHSRACHPSPollPDU (AM RLC period Poll_PDU for PS NRT with
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2029
AMRLCHSRACHPSPollSDU (AM RLC period Poll_SDU for PS NRT with
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2030
AMRLCHSRACHPSPollWin (AM RLC period Poll_Window for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2031
AMRLCHSRACHPSTriggers (AM RLC status report triggers for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2033
HSRACHAMRLCRespHSFACH (AM RLC round trip time with HS-RACH/HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2035
AMRLCMaximumBufferUE (AM RLC maximum buffer allocation for UE) .
2036
AMRLCMaximumBufferUE100 (AM RLC maximum buffer allocation for UE
capability 100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2038
AMRLCMaximumBufferUE1150 (AM RLC maximum buffer allocation for
UE capability 1150). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2039
AMRLCMaximumBufferUE1250 (AM RLC maximum buffer allocation for
UE capability 1250). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2040
AMRLCMaximumBufferUE150 (AM RLC maximum buffer allocation for UE
capability 150) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2041
AMRLCMaximumBufferUE1k (AM RLC maximum buffer allocation for UE
capability 1000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2042
AMRLCMaximumBufferUE200 (AM RLC maximum buffer allocation for UE
capability 200) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2043
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
36.33
36.34
36.35
36.36
36.37
36.38
36.39
36.40
36.41
36.42
36.43
36.44
36.45
36.46
36.47
36.48
36.49
36.50
36.51
36.52
36.53
36.54
36.55
36.56
36.57
DN00211177
Issue 12B
AMRLCMaximumBufferUE300 (AM RLC maximum buffer allocation for UE
capability 300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2044
AMRLCMaximumBufferUE50 (AM RLC maximum buffer allocation for UE
capability 50) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2045
AMRLCMaximumBufferUE500 (AM RLC maximum buffer allocation for UE
capability 500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2046
AMRLCMaximumBufferUE750 (AM RLC maximum buffer allocation for UE
capability 750) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2047
AMRLCmaximumBufferUE400 (AM RLC maximum buffer allocation for UE
capability 400) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2049
AMRLCOnDCHOfNRTPS (AM RLC configuration for PS NRT with DCH)
2050
AMRLCOnDCHOfNRTPSCount (AM RLC status reports count for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2051
AMRLCOnDCHOfNRTPSFilterReTX (AM RLC retransmission filter for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2053
AMRLCOnDCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2055
AMRLCOnDCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2056
AMRLCOnDCHOfNRTPSMaxRST (AM RLC MaxRST transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2058
AMRLCOnDCHOfNRTPSPeriodMax (AM RLC status period max for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2059
AMRLCOnDCHOfNRTPSPeriodMin (AM RLC status period min for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2060
AMRLCOnDCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2061
AMRLCOnDCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2063
AMRLCOnDCHOfNRTPSPollWindow (AM RLC period Poll_Window for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2064
AMRLCOnDCHOfNRTPSTriggers (AM RLC status report triggers for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2065
AMRLCOnDCHOfSRB136 (AM RLC configuration for SRB13.6 with DCH)
2068
AMRLCOnDCHOfSRB136MaxDAT (AM RLC MaxDAT transmissions for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2069
AMRLCOnDCHOfSRB136PeriodMax (AM RLC status period max for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2070
AMRLCOnDCHOfSRB136PeriodMin (AM RLC status period min for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2071
AMRLCOnDCHOfSRB136PollPDU (AM RLC period Poll_PDU for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2072
AMRLCOnDCHOfSRB136PollSDU (AM RLC period Poll_SDU for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2074
AMRLCOnDCHOfSRB136PollWindow (AM RLC period Poll_Window for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2075
AMRLCOnDCHOfSRB136Triggers (AM RLC status report triggers for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2076
Id:0900d805809d7397
59
WCDMA Radio Network Configuration Parameters
36.58
36.59
36.60
36.61
36.62
36.63
36.64
36.65
36.66
36.67
36.68
36.69
36.70
36.71
36.72
36.73
36.74
36.75
36.76
36.77
36.78
36.79
36.80
36.81
36.82
60
AMRLCOnDCHOfSRB34 (AM RLC configuration for SRB3.4 with DCH) .
2078
AMRLCOnDCHOfSRB34MaxDAT (AM RLC MaxDAT transmissions for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2079
AMRLCOnDCHOfSRB34PeriodMax (AM RLC status period max for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2080
AMRLCOnDCHOfSRB34PeriodMin (AM RLC status period min for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2082
AMRLCOnDCHOfSRB34PollPDU (AM RLC period Poll_PDU for SRB3.4
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2083
AMRLCOnDCHOfSRB34PollSDU (AM RLC period Poll_SDU for SRB3.4
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2084
AMRLCOnDCHOfSRB34PollWindow (AM RLC period Poll_Window for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2085
AMRLCOnDCHOfSRB34Triggers (AM RLC status report triggers for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2086
AMRLCOnDCHOfStream (AM RLC configuration for PS streaming with
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2088
AMRLCOnDCHOfStreamCount (AM RLC status reports count for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2089
AMRLCOnDCHOfStreamDiscardTime (AM RLC SDU discard time for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2091
AMRLCOnDCHOfStreamFilterReTX (AM RLC retransmission filter for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2092
AMRLCOnDCHOfStreamMaxDAT (AM RLC MaxDAT transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2094
AMRLCOnDCHOfStreamMaxMRW (AM RLC MaxMRW transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2095
AMRLCOnDCHOfStreamMaxRST (AM RLC MaxRST transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2097
AMRLCOnDCHOfStreamPeriodMax (AM RLC status period max for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2098
AMRLCOnDCHOfStreamPeriodMin (AM RLC status period min for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2099
AMRLCOnDCHOfStreamPollPDU (AM RLC period Poll_PDU for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2100
AMRLCOnDCHOfStreamPollSDU (AM RLC period Poll_SDU for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2102
AMRLCOnDCHOfStreamPollWindow (AM RLC period Poll_Window for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2103
AMRLCOnDCHOfStreamTriggers (AM RLC status report triggers for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2104
AMRLCOnDCHSRB136OffSat (AM RLC timer offset for SRB13.6 with satellite DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2106
AMRLCOnEDCHOfNRTPS (AM RLC configuration for PS NRT with EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2108
AMRLCOnEDCHOfNRTPSCount (AM RLC status reports count for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2109
AMRLCOnEDCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2111
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
36.83
36.84
36.85
36.86
36.87
36.88
36.89
36.90
36.91
36.92
36.93
36.94
36.95
36.96
36.97
36.98
36.99
36.100
36.101
36.102
36.103
36.104
36.105
36.106
36.107
DN00211177
Issue 12B
AMRLCOnEDCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions
for PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2112
AMRLCOnEDCHOfNRTPSMaxRST (AM RLC maxRST transmissions for
PS NRT with E-DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2113
AMRLCOnEDCHOfNRTPSPeriodMax (AM RLC status period max for PS
NRT with E-DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2114
AMRLCOnEDCHOfNRTPSPeriodMin (AM RLC status period min for PS
NRT with E-DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2116
AMRLCOnEDCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS
NRT with E-DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2117
AMRLCOnEDCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS
NRT with E-DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2118
AMRLCOnEDCHOfNRTPSPollWindow (AM RLC period Poll_Window for
PS NRT with E-DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2119
AMRLCOnEDCHOfNRTPSTriggers (AM RLC status report triggers for PS
NRT with E-DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2120
AMRLCOnEDCHOfStrPS (AM RLC configuration for PS streaming with EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2122
EDCHStrPSCount (AM RLC status reports count for PS streaming E-DCH)
2124
EDCHStrPSDiscardTime (AM RLC SDU discard time for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2126
EDCHStrPSMaxDAT (AM RLC MaxDAT transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2127
EDCHStrPSMaxMRW (AM RLC MaxMRW transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2128
EDCHStrPSMaxRST (AM RLC maxRST transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2129
EDCHStrPSPeriodMax (AM RLC status period max for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2130
EDCHStrPSPeriodMin (AM RLC status period min for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2132
EDCHStrPSPollPDU (AM RLC period Poll_PDU for PS streaming E-DCH)
2133
EDCHStrPSPollSDU (AM RLC period Poll_SDU for PS streaming E-DCH)
2134
EDCHStrPSPollWindow (AM RLC period Poll_Window for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2135
EDCHStrPSTriggers (AM RLC status report triggers for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2136
AMRLCOnFACHOfPS (AM RLC configuration for PS NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2138
AMRLCOnFACHOfPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2140
AMRLCOnFACHOfPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2141
AMRLCOnFACHOfPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with FACH/RAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2142
AMRLCOnFACHOfPSPeriodMax (AM RLC status period max for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2143
Id:0900d805809d7397
61
WCDMA Radio Network Configuration Parameters
36.108
36.109
36.110
36.111
36.112
36.113
36.114
36.115
36.116
36.117
36.118
36.119
36.120
36.121
36.122
36.123
36.124
36.125
36.126
36.127
36.128
36.129
36.130
36.131
36.132
62
AMRLCOnFACHOfPSPeriodMin (AM RLC status period min for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2144
AMRLCOnFACHOfPSPollPDU (AM RLC period Poll_PDU for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2145
AMRLCOnFACHOfPSPollSDU (AM RLC period Poll_SDU for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2147
AMRLCOnFACHOfPSPollWindow (AM RLC period Poll_Window for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2148
AMRLCOnFACHOfPSTriggers (AM RLC status report triggers for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2149
AMRLCOnFACHOfSRB (AM RLC configuration for SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2151
AMRLCOnFACHOfSRBMaxDAT (AM RLC MaxDAT transmissions for
SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2152
AMRLCOnFACHOfSRBPeriodMax (AM RLC status period max for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2154
AMRLCOnFACHOfSRBPeriodMin (AM RLC status period min for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2155
AMRLCOnFACHOfSRBPollPDU (AM RLC period Poll_PDU for SRB with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2156
AMRLCOnFACHOfSRBPollSDU (AM RLC period Poll_SDU for SRB with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2158
AMRLCOnFACHOfSRBPollWindow (AM RLC period Poll_Window for
SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2159
AMRLCOnFACHOfSRBTriggers (AM RLC status report triggers for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2160
AMRLCOnHSDSCHOfNRTPS (AM RLC configuration for PS NRT with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2162
AMRLCOnHSDSCHOfNRTPSCount (AM RLC status reports count for PS
NRT with HS-DSCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2163
AMRLCOnHSDSCHOfNRTPSFilterReTX (AM RLC retransmission filter
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2165
AMRLCOnHSDSCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2167
AMRLCOnHSDSCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2168
AMRLCOnHSDSCHOfNRTPSMaxRST (AM RLC maxRST transmissions
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2169
AMRLCOnHSDSCHOfNRTPSPeriodMax (AM RLC status period max for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2170
AMRLCOnHSDSCHOfNRTPSPeriodMin (AM RLC status period min for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2172
AMRLCOnHSDSCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS
NRT with HS-DSCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2173
AMRLCOnHSDSCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS
NRT with HS-DSCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2174
AMRLCOnHSDSCHOfNRTPSPollWindow (AM RLC period Poll_Window
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2175
AMRLCOnHSDSCHOfNRTPSTriggers (AM RLC status report triggers for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2176
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
36.133
36.134
36.135
36.136
36.137
36.138
36.139
36.140
36.141
36.142
36.143
36.144
36.145
36.146
36.147
36.148
36.149
36.150
36.151
36.152
36.153
36.154
36.155
36.156
36.157
DN00211177
Issue 12B
AMRLCOnHSDSCHOfStrPS (AM RLC configuration for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2179
HSDSCHStrDiscardTime (AM RLC SDU discard time for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2180
HSDSCHStrPSCount (AM RLC status reports count for PS stream with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2182
HSDSCHStrPSFilterReTX (AM RLC retransmission filter for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2183
HSDSCHStrPSMaxDAT (AM RLC MaxDAT transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2185
HSDSCHStrPSMaxMRW (AM RLC MaxMRW transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2186
HSDSCHStrPSMaxRST (AM RLC maxRST transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2187
HSDSCHStrPSPeriodMax (AM RLC status period max for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2188
HSDSCHStrPSPeriodMin (AM RLC status period min for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2190
HSDSCHStrPSPollPDU (AM RLC period Poll_PDU for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2191
HSDSCHStrPSPollSDU (AM RLC period Poll_SDU for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2192
HSDSCHStrPSPollWindow (AM RLC period Poll_Window for PS streaming with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2193
HSDSCHStrPSTriggers (AM RLC status report triggers for PS str with HSDSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2194
AMRLCPeriodMaxHSSRB (AM RLC status period max for SRBs with HSRACH/HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2197
AMRLCRTTPollPDUSatellite (AM RLC period Poll_PDU with satellite Iub)
2198
AMRLCRelatTXWindow (AM RLC relative transmission window sizes) . .
2199
AMRLCRelatTXWindowRate1 (AM RLC relative Tx window size defining
data rate 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2200
AMRLCRelatTXWindowRate1Size (AM RLC relative Tx window size assigned to data rate 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2201
AMRLCRelatTXWindowRate2 (AM RLC relative Tx window size defining
data rate 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2203
AMRLCRelatTXWindowRate2Size (AM RLC relative Tx window size assigned to data rate 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2204
AMRLCRelatTXWindowRate3 (AM RLC relative Tx window size defining
data rate 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2205
AMRLCRelatTXWindowRate3Size (AM RLC relative Tx window size assigned to data rate 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2206
AMRLCRelatTXWindowRate4 (AM RLC relative Tx window size defining
data rate 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2207
AMRLCRelatTXWindowRate4Size (AM RLC relative Tx window size assigned to data rate 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2208
AMRLCRelatTXWindowRate5 (AM RLC relative Tx window size defining
data rate 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2209
Id:0900d805809d7397
63
WCDMA Radio Network Configuration Parameters
36.158
36.159
36.160
36.161
36.162
36.163
36.164
36.165
36.166
36.167
36.168
36.169
36.170
36.171
36.172
36.173
36.174
36.175
36.176
36.177
36.178
36.179
36.180
36.181
36.182
36.183
36.184
64
AMRLCRelatTXWindowRate5Size (AM RLC relative Tx window size assigned to data rate 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2210
AMRLCRelatTXWindowRate6 (AM RLC relative Tx window size defining
data rate 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2211
AMRLCRelatTXWindowRate6Size (AM RLC relative Tx window size assigned to data rate 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2212
AMRLCRelatTXWindowRate7 (AM RLC relative Tx window size defining
data rate 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2213
AMRLCRelatTXWindowRate7Size (AM RLC relative Tx window size assigned to data rate 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2214
AMRLCRelatTXWindowRate8 (AM RLC relative Tx window size defining
data rate 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2215
AMRLCRelatTXWindowRate8Size (AM RLC relative Tx window size assigned to data rate 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2216
AMRLCRespTimeDCH (AM RLC round trip times with DCH) . . . . . . 2217
AMRLCRespTimeDCH10 (AM RLC round trip time with DCH/DCH of TTI
10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2218
AMRLCRespTimeDCH20 (AM RLC round trip time with DCH/DCH of TTI
20 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2219
AMRLCRespTimeDCH40 (AM RLC round trip time with DCH/DCH of TTI
40 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2220
AMRLCRespTimeDCHRevHSDSCH (AM RLC round trip time for
DCH/HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2221
AMRLCRespTimeRevEDCH (AM RLC round trip time for E-DCH/DCH) . .
2222
AMRLCRespTimeEDCH (AM RLC round trip time with E-DCH) . . . . 2223
AMRLCRespTimeFACHAndRACH (AM RLC round trip time with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2224
AMRLCRespTimeHSDSCH (AM RLC round trip times with HS-DSCH) . .
2225
AMRLCRespTimeHSDSCHRevDCH (AM RLC round trip time with HSDSCH/DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2226
AMRLCRespTimeHSDSCHRevEDCH (AM RLC round trip time with HSDSCH/E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2227
AMRLCRespTimeHSSRB (AM RLC round trip time for SRBs with HS-RACH/HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2228
AMRLCSRB3n4PeriodMax (AM RLC status period max for SRB3 and
SRB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2229
AMRLCSRB3n4RespTime (AM RLC round trip time for SRB3 and SRB4)
2230
AMRLCSRBHSPA (AM RLC configuration for SRB on HSPA) . . . . . 2232
AMRLCRespTimeSRBHSPA (AM RLC round trip time for SRB on HSPA)
2233
AMRLCSRBHSPAMaxDAT (AM RLC MaxDAT transmissions for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2234
AMRLCSRBHSPAPeriodMax (AM RLC status period max for SRB on HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2235
AMRLCSRBHSPAPeriodMin (AM RLC status period min for SRB on HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2236
AMRLCSRBHSPAPollPDU (AM RLC period Poll_PDU for SRB on HSPA)
2237
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
36.185
36.186
36.187
36.188
36.189
36.190
36.191
36.192
36.193
36.194
36.195
36.196
36.197
36.198
36.199
36.200
37
37.1
37.2
37.3
37.4
37.5
37.6
37.7
37.8
37.9
37.10
37.11
37.12
37.13
37.14
37.15
DN00211177
Issue 12B
AMRLCSRBHSPAPollSDU (AM RLC period Poll_SDU for SRB on HSPA)
2239
AMRLCSRBHSPAPollWindow (AM RLC period Poll_Window for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2240
AMRLCSRBHSPATriggers (AM RLC status report triggers for SRB on HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2241
AMRLCTXWindowSizeSRB (AM RLC transmission window sizes for SRBs
2, 3 and 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2243
AMRLCTXWindowSizeSRB2 (AM RLC transmission window size for SRB
2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2244
AMRLCTXWindowSizeSRB3 (AM RLC transmission window size for SRB
3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2245
AMRLCTXWindowSizeSRB4 (AM RLC transmission window size for SRB
4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2247
PDUSizeBitRateThr (Bit rate threshold for RLC PDU size 656 with HSDSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2248
PDUSizeCodeThreshold (Number of HS-PDSCH codes for greater RLC
PDU size). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2249
PDUSizeSIRThr (SIR threshold for RLC PDU size 656 with HS-DSCH). .
2251
RLCConfOptionFPS (RLC Conf option switch for Fast Cell_PCH Switching) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2252
RNRLCChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . 2254
RNRLCId (RNRLC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2255
SDUdiscardModeRTPS (SDU discard mode for RT PS RAB employing
RLC AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2256
UMRLCEVoiceDiscardTime (UM RLC SDU discard time in UE for CS voice
over HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2257
UMRLCPTTDiscardTime (UM RLC SDU discard time in UE for PTT) 2258
RNTRM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2260
A2EA (AAL type 2 end point address for Iur). . . . . . . . . . . . . . . . . . . 2260
ActivityFactorForAMRDCHTrafficBearers (Activity factor for AMR DCH
traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2262
Af122AMRDL (Activity factor for 12.2 / 12.65 AMR DCH DL bearer) 2263
Af122AMRUL (Activity factor for 12.2 / 12.65 AMR DCH UL bearer) 2264
Af59AMRDL (Activity factor for 5.9 AMR DCH DL bearer) . . . . . . . . 2265
Af59AMRUL (Activity factor for 5.9 AMR DCH UL bearer) . . . . . . . . 2266
ActivityFactorForCSDCHTrafficBearers (Activity factor for CS DCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2267
Af144CSStreDL (Activity factor for 14.4 CS streaming DL bearer) . . 2268
Af144CSStreUL (Activity factor for 14.4 CS streaming UL bearer) . . 2269
Af576CSStreDL (Activity factor for 57.6 CS streaming DL bearer) . . 2270
Af576CSStreUL (Activity factor for 57.6 CS streaming UL bearer) . . 2271
Af64CSConDL (Activity factor for 64 CS conversational DL bearer) . 2272
Af64CSConUL (Activity factor for 64 CS conversational UL bearer) . 2273
ActivityFactorForDCCHTrafficBearers (Activity factor for DCCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2274
Af128And136DCCHDL (Activity factor for 12.8/13.6 DCCH DL bearer) . .
2275
Id:0900d805809d7397
65
WCDMA Radio Network Configuration Parameters
37.16
37.17
37.18
37.19
37.20
37.21
37.22
37.23
37.24
37.25
37.26
37.27
37.28
37.29
37.30
37.31
37.32
37.33
37.34
37.35
37.36
37.37
37.38
37.39
37.40
37.41
37.42
37.43
37.44
37.45
37.46
37.47
37.48
37.49
37.50
37.51
37.52
37.53
37.54
37.55
37.56
37.57
37.58
66
Af128And136DCCHUL (Activity factor for 12.8/13.6 DCCH UL bearer). . .
2276
Af16And17DCCHDL (Activity factor for 1.6/1.7 DCCH DL bearer) . . . 2277
Af16And17DCCHUL (Activity factor for 1.6/1.7 DCCH UL bearer) . . . 2278
Af32And34DCCHDL (Activity factor for 3.2/3.4 DCCH DL bearer) . . . 2279
Af32And34DCCHUL (Activity factor for 3.2/3.4 DCCH UL bearer) . . . 2280
ActivityFactorForFACHRACHTrafficBearers (Activity factor for FACH and
RACH traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2281
AfFACHCCDL (Activity factor for FACH-C/C DL bearer) . . . . . . . . . . 2282
AfFACHCIDL (Activity factor for FACH-C/I DL bearer) . . . . . . . . . . . . 2283
AfFACHContUL (Activity factor for FACH control UL bearer) . . . . . . . 2284
AfFACHSDL (Activity factor for FACH-S DL bearer) . . . . . . . . . . . . . 2285
AfFACHUDL (Activity factor for FACH-U DL bearer) . . . . . . . . . . . . . 2286
AfRACH208UL (Activity factor for RACH 20.8 UL bearer) . . . . . . . . . 2287
AfRACHContDL (Activity factor for RACH control DL bearer) . . . . . . 2288
ActivityFactorForHSPA (Activity factor for HSPA bearers) . . . . . . . . . 2289
AfPTTDL (Activity Factor for PTT RAB in Downlink) . . . . . . . . . . . . . 2290
AfPTTUL (Activity Factor for PTT RAB in Uplink) . . . . . . . . . . . . . . . . 2291
AfRTHSDPA (Activity factor for RT HSDPA bearer) . . . . . . . . . . . . . . 2292
AfRTHSUPA (Activity factor for RT HSUPA bearer) . . . . . . . . . . . . . . 2293
AfSRBOnHSDPA (Activity factor for SRB on HSDPA bearer) . . . . . . 2294
AfSRBOnHSUPA (Activity factor for SRB on HSUPA bearer) . . . . . . 2295
ActivityFactorForNRTDCHTrafficBearers (Activity factor for NRT DCH traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2296
Af128NRTDCHDL (Activity factor for 128 NRT DCH DL bearer) . . . . 2297
Af128NRTDCHUL (Activity factor for 128 NRT DCH UL bearer) . . . . 2298
Af16NRTDCHDL (Activity factor for 16 NRT DCH DL bearer) . . . . . . 2299
Af16NRTDCHUL (Activity factor for 16 NRT DCH UL bearer) . . . . . . 2300
Af256NRTDCHDL (Activity factor for 256 NRT DCH DL bearer) . . . . 2301
Af256NRTDCHUL (Activity factor for 256 NRT DCH UL bearer) . . . . 2302
Af32NRTDCHDL (Activity factor for 32 NRT DCH DL bearer) . . . . . . 2303
Af32NRTDCHUL (Activity factor for 32 NRT DCH UL bearer) . . . . . . 2304
Af384NRTDCHDL (Activity factor for 384 NRT DCH DL bearer) . . . . 2305
Af384NRTDCHUL (Activity factor for 384 NRT DCH UL bearer) . . . . 2306
Af64NRTDCHDL (Activity factor for 64 NRT DCH DL bearer) . . . . . . 2307
Af64NRTDCHUL (Activity factor for 64 NRT DCH UL bearer) . . . . . . 2308
Af8NRTDCHDL (Activity factor for 8 NRT DCH DL bearer) . . . . . . . . 2309
Af8NRTDCHUL (Activity factor for 8 NRT DCH UL bearer) . . . . . . . . 2310
ActivityFactorForPCHTrafficBearers (Activity factor for PCH traffic bearers)
2311
AfPCHContUL (Activity factor for PCH control UL bearer) . . . . . . . . . 2312
AfPCHDL (Activity factor for PCH DL bearer). . . . . . . . . . . . . . . . . . . 2313
ActivityFactorForRTPSTrafficBearers (Activity factor for RT PS traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2314
Af128RTPSAMDL (Activity factor for 128 RT PS AM DL bearer) . . . . 2316
Af128RTPSAMUL (Activity factor for 128 RT PS AM UL bearer) . . . . 2317
Af128RTPSUMDL (Activity factor for 128 RT PS UM DL bearer). . . . 2318
Af128RTPSUMUL (Activity factor for 128 RT PS UM UL bearer). . . . 2319
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
37.59
37.60
37.61
37.62
37.63
37.64
37.65
37.66
37.67
37.68
37.69
37.70
37.71
37.72
37.73
37.74
37.75
37.76
37.77
37.78
37.79
37.80
37.81
37.82
37.83
37.84
37.85
37.86
37.87
37.88
37.89
37.90
37.91
37.92
37.93
37.94
37.95
37.96
37.97
37.98
DN00211177
Issue 12B
Af16RTPSAMDL (Activity factor for 16 RT PS AM DL bearer) . . . . . 2320
Af16RTPSAMUL (Activity factor for 16 RT PS AM UL bearer) . . . . . 2321
Af16RTPSUMDL (Activity factor for 16 RT PS UM DL bearer) . . . . . 2322
Af16RTPSUMUL (Activity factor for 16 RT PS UM UL bearer) . . . . . 2323
Af256RTPSAMDL (Activity factor for 256 RT PS AM DL bearer) . . . 2324
Af256RTPSUMDL (Activity factor for 256 RT PS UM DL bearer) . . . 2325
Af32RTPSAMDL (Activity factor for 32 RT PS AM DL bearer) . . . . . 2326
Af32RTPSAMUL (Activity factor for 32 RT PS AM UL bearer) . . . . . 2327
Af32RTPSUMDL (Activity factor for 32 RT PS UM DL bearer) . . . . . 2328
Af32RTPSUMUL (Activity factor for 32 RT PS UM UL bearer) . . . . . 2329
Af64RTPSAMDL (Activity factor for 64 RT PS AM DL bearer) . . . . . 2330
Af64RTPSAMUL (Activity factor for 64 RT PS AM UL bearer) . . . . . 2331
Af64RTPSUMDL (Activity factor for 64 RT PS UM DL bearer) . . . . . 2332
Af64RTPSUMUL (Activity factor for 64 RT PS UM UL bearer) . . . . . 2333
Af8RTPSAMDL (Activity factor for 8 RT PS AM DL bearer) . . . . . . . 2334
Af8RTPSAMUL (Activity factor for 8 RT PS AM UL bearer) . . . . . . . 2335
Af8RTPSUMDL (Activity factor for 8 RT PS UM DL bearer) . . . . . . . 2336
Af8RTPSUMUL (Activity factor for 8 RT PS UM UL bearer) . . . . . . . 2337
DSCPBTSOMToBTS (DSCP for BTS OM towards BTS) . . . . . . . . . 2338
DSCPBTSOMToOMS (DSCP for BTS OM towards OMS) . . . . . . . . 2338
DSCPForGTPSignalling (DSCP for GTP signalling) . . . . . . . . . . . . . 2339
EchoRequestSending (Echo Request Sending) . . . . . . . . . . . . . . . . 2340
HSDPAFlowControlLowThresholdDedicatedVCC (HSDPA flow control
AAL2 low threshold for dedicated VCC) . . . . . . . . . . . . . . . . . . . . . . 2342
HSDPAFlowControlLowThresholdSharedVCC (HSDPA flow control AAL2
low threshold for shared VCC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2343
HSDPAFlowControlTargetDelayDedicatedVCC (HSDPA flow control
AAL2 target delay for dedicated VCC). . . . . . . . . . . . . . . . . . . . . . . . 2344
HSDPAFlowControlTargetDelaySharedVCC (HSDPA flow control AAL2
target delay for shared VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2345
IPStackErrorTimer (IP Stack Error timer). . . . . . . . . . . . . . . . . . . . . . 2346
IuDATree (Iu-CS Digit analysis tree) . . . . . . . . . . . . . . . . . . . . . . . . . 2347
IubDATree (Iub Digit analysis tree) . . . . . . . . . . . . . . . . . . . . . . . . . . 2348
IurDATree (Iur Digit analysis tree) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2348
N3Requests (N3-REQUESTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2349
NRTDCHFlowControlTargetDelay (NRTDCH Flow Control Target Delay)
2350
RNTRMChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 2351
RNTRMId (RNTRM Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2353
RespSyncCounterIP (Response synchronization counter for DL synch
frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2354
RespSyncModEnableIP (IP Iub DCH Sync Modifiable) . . . . . . . . . . . 2355
RespSyncTimerIP (IP Response synchronization timer for DL synch
frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2356
RespSyncTimerSatIP (IP Response synchronization timer with Satellite
Iub). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2357
T3Response (T3-RESPONSE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2358
THP1DelaySensitivitySwitch (THP 1 Delay Sensitivity Switch) . . . . . 2359
Id:0900d805809d7397
67
WCDMA Radio Network Configuration Parameters
37.99
37.100
37.101
37.102
37.103
37.104
38
38.1
38.2
38.3
38.4
38.5
38.6
38.7
38.8
38.9
38.10
38.11
38.12
38.13
38.14
38.15
38.16
38.17
38.18
38.19
38.20
38.21
38.22
38.23
38.24
38.25
38.26
38.27
38.28
38.29
38.30
38.31
38.32
38.33
38.34
38.35
38.36
68
THP2DelaySensitivitySwitch (THP 2 Delay Sensitivity Switch) . . . . . 2360
THP3DelaySensitivitySwitch (THP 3 Delay Sensitivity Switch) . . . . . 2361
ToAWEOffsetForOverbook (ToAWE Offset for overbooked NRT DCH
AAL2 connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2362
ToAWSOffsetForOverbook (ToAWS Offset for overbooked NRT DCH
AAL2 connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2364
ULCACSwitch (Enhanced UL CAC Algorithm Switch) . . . . . . . . . . . . 2365
UsedSRBALCSet (Used SRB ALC set) . . . . . . . . . . . . . . . . . . . . . . . 2366
TQM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2370
AFForHSPATrafficBearers (Activity Factor For HSPA Traffic Bearers) . . .
2370
AfHSDPAQoSPri0 (Activity Factor HSDPA QoSPri0). . . . . . . . . . . . . 2372
AfHSDPAQoSPri1 (Activity Factor HSDPA QoSPri1). . . . . . . . . . . . . 2373
AfHSDPAQoSPri10 (Activity Factor HSDPA QoSPri10). . . . . . . . . . . 2374
AfHSDPAQoSPri11 (Activity Factor HSDPA QoSPri11). . . . . . . . . . . 2375
AfHSDPAQoSPri12 (Activity Factor HSDPA QoSPri12). . . . . . . . . . . 2376
AfHSDPAQoSPri13 (Activity Factor HSDPA QoSPri13). . . . . . . . . . . 2377
AfHSDPAQoSPri14 (Activity Factor HSDPA QoSPri14). . . . . . . . . . . 2378
AfHSDPAQoSPri15 (Activity Factor HSDPA QoSPri15). . . . . . . . . . . 2379
AfHSDPAQoSPri2 (Activity Factor HSDPA QoSPri2). . . . . . . . . . . . . 2380
AfHSDPAQoSPri3 (Activity Factor HSDPA QoSPri3). . . . . . . . . . . . . 2381
AfHSDPAQoSPri4 (Activity Factor HSDPA QoSPri4). . . . . . . . . . . . . 2382
AfHSDPAQoSPri5 (Activity Factor HSDPA QoSPri5). . . . . . . . . . . . . 2383
AfHSDPAQoSPri6 (Activity Factor HSDPA QoSPri6). . . . . . . . . . . . . 2384
AfHSDPAQoSPri7 (Activity Factor HSDPA QoSPri7). . . . . . . . . . . . . 2385
AfHSDPAQoSPri8 (Activity Factor HSDPA QoSPri8). . . . . . . . . . . . . 2386
AfHSDPAQoSPri9 (Activity Factor HSDPA QoSPri9). . . . . . . . . . . . . 2387
AfHSUPAQoSPri0 (Activity Factor HSUPA QoSPri0). . . . . . . . . . . . . 2388
AfHSUPAQoSPri1 (Activity Factor HSUPA QoSPri1). . . . . . . . . . . . . 2389
AfHSUPAQoSPri10 (Activity Factor HSUPA QoSPri10). . . . . . . . . . . 2390
AfHSUPAQoSPri11 (Activity Factor HSUPA QoSPri11). . . . . . . . . . . 2391
AfHSUPAQoSPri12 (Activity Factor HSUPA QoSPri12). . . . . . . . . . . 2392
AfHSUPAQoSPri13 (Activity Factor HSUPA QoSPri13). . . . . . . . . . . 2393
AfHSUPAQoSPri14 (Activity Factor HSUPA QoSPri14). . . . . . . . . . . 2394
AfHSUPAQoSPri15 (Activity Factor HSUPA QoSPri15). . . . . . . . . . . 2395
AfHSUPAQoSPri2 (Activity Factor HSUPA QoSPri2). . . . . . . . . . . . . 2396
AfHSUPAQoSPri3 (Activity Factor HSUPA QoSPri3). . . . . . . . . . . . . 2397
AfHSUPAQoSPri4 (Activity Factor HSUPA QoSPri4). . . . . . . . . . . . . 2398
AfHSUPAQoSPri5 (Activity Factor HSUPA QoSPri5). . . . . . . . . . . . . 2399
AfHSUPAQoSPri6 (Activity Factor HSUPA QoSPri6). . . . . . . . . . . . . 2400
AfHSUPAQoSPri7 (Activity Factor HSUPA QoSPri7). . . . . . . . . . . . . 2401
AfHSUPAQoSPri8 (Activity Factor HSUPA QoSPri8). . . . . . . . . . . . . 2402
AfHSUPAQoSPri9 (Activity Factor HSUPA QoSPri9). . . . . . . . . . . . . 2403
FallbackForDCHQoSPri0 (Fallback for DCH QoS Priority 0 Mapping)2404
FallbackForDCHQoSPri1 (Fallback for DCH QoS Priority 1 Mapping)2405
FallbackForDCHQoSPri10 (Fallback for DCH QoS Priority 10 Mapping). .
2406
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
38.37
38.38
38.39
38.40
38.41
38.42
38.43
38.44
38.45
38.46
38.47
38.48
38.49
38.50
38.51
38.52
38.53
38.54
38.55
38.56
38.57
38.58
38.59
38.60
38.61
38.62
38.63
38.64
38.65
DN00211177
Issue 12B
FallbackForDCHQoSPri11 (Fallback for DCH QoS Priority 11 Mapping) .
2407
FallbackForDCHQoSPri12 (Fallback for DCH QoS Priority 12 Mapping) .
2408
FallbackForDCHQoSPri13 (Fallback for DCH QoS Priority 13 Mapping) .
2409
FallbackForDCHQoSPri14 (Fallback for DCH QoS Priority 14 Mapping) .
2410
FallbackForDCHQoSPri15 (Fallback for DCH QoS Priority 15 Mapping) .
2412
FallbackForDCHQoSPri2 (Fallback for DCH QoS Priority 2 Mapping)2413
FallbackForDCHQoSPri3 (Fallback for DCH QoS Priority 3 Mapping)2414
FallbackForDCHQoSPri4 (Fallback for DCH QoS Priority 4 Mapping)2415
FallbackForDCHQoSPri5 (Fallback for DCH QoS Priority 5 Mapping)2416
FallbackForDCHQoSPri6 (Fallback for DCH QoS Priority 6 Mapping)2417
FallbackForDCHQoSPri7 (Fallback for DCH QoS Priority 7 Mapping)2418
FallbackForDCHQoSPri8 (Fallback for DCH QoS Priority 8 Mapping)2420
FallbackForDCHQoSPri9 (Fallback for DCH QoS Priority 9 Mapping)2421
FallbackForHSPAQoSPri0 (Fallback for HSPA QoS Priority 0 Mapping) .
2422
FallbackForHSPAQoSPri1 (Fallback for HSPA QoS Priority 1 Mapping) .
2423
FallbackForHSPAQoSPri10 (Fallback for HSPA QoS Priority 10 Mapping)
2424
FallbackForHSPAQoSPri11 (Fallback for HSPA QoS Priority 11 Mapping)
2425
FallbackForHSPAQoSPri12 (Fallback for HSPA QoS Priority 12 Mapping)
2426
FallbackForHSPAQoSPri13 (Fallback for HSPA QoS Priority 13 Mapping)
2428
FallbackForHSPAQoSPri14 (Fallback for HSPA QoS Priority 14 Mapping)
2429
FallbackForHSPAQoSPri15 (Fallback for HSPA QoS Priority 15 Mapping)
2430
FallbackForHSPAQoSPri2 (Fallback for HSPA QoS Priority 2 Mapping) .
2431
FallbackForHSPAQoSPri3 (Fallback for HSPA QoS Priority 3 Mapping) .
2432
FallbackForHSPAQoSPri4 (Fallback for HSPA QoS Priority 4 Mapping) .
2433
FallbackForHSPAQoSPri5 (Fallback for HSPA QoS Priority 5 Mapping) .
2434
FallbackForHSPAQoSPri6 (Fallback for HSPA QoS Priority 6 Mapping) .
2436
FallbackForHSPAQoSPri7 (Fallback for HSPA QoS Priority 7 Mapping) .
2437
FallbackForHSPAQoSPri8 (Fallback for HSPA QoS Priority 8 Mapping) .
2438
FallbackForHSPAQoSPri9 (Fallback for HSPA QoS Priority 9 Mapping) .
2439
Id:0900d805809d7397
69
WCDMA Radio Network Configuration Parameters
38.66
38.67
38.68
38.69
38.70
38.71
38.72
38.73
38.74
38.75
38.76
38.77
38.78
38.79
38.80
38.81
38.82
38.83
38.84
38.85
38.86
38.87
38.88
38.89
38.90
38.91
70
QosPriToAAL2PT (Qos Priority To AAL2PT ). . . . . . . . . . . . . . . . . . . 2440
CSTrafficToAAL2PT (CS Traffic to AAL2 Path Type mapping) . . . . . 2443
DCHQoSPri0ToAAL2PT (DCH QoSPri0 to AAL2 Path Type mapping) . . .
2444
DCHQoSPri10ToAAL2PT (DCH QoSPri10 to AAL2 Path Type mapping) .
2446
DCHQoSPri11ToAAL2PT (DCH QoSPri11 to AAL2 Path Type mapping) .
2448
DCHQoSPri12ToAAL2PT (DCH QoSPri12 to AAL2 Path Type mapping) .
2449
DCHQoSPri13ToAAL2PT (DCH QoSPri13 to AAL2 Path Type mapping) .
2451
DCHQoSPri14ToAAL2PT (DCH QoSPri14 to AAL2 Path Type mapping) .
2453
DCHQoSPri15ToAAL2PT (DCH QoSPri15 to AAL2 Path Type mapping) .
2454
DCHQoSPri1ToAAL2PT (DCH QoSPri1 to AAL2 Path Type mapping) . . .
2456
DCHQoSPri2ToAAL2PT (DCH QoSPri2 to AAL2 Path Type mapping) . . .
2458
DCHQoSPri3ToAAL2PT (DCH QoSPri3 to AAL2 Path Type mapping) . . .
2459
DCHQoSPri4ToAAL2PT (DCH QoSPri4 to AAL2 Path Type mapping) . . .
2461
DCHQoSPri5ToAAL2PT (DCH QoSPri5 to AAL2 Path Type mapping) . . .
2463
DCHQoSPri6ToAAL2PT (DCH QoSPri6 to AAL2 Path Type mapping) . . .
2464
DCHQoSPri7ToAAL2PT (DCH QoSPri7 to AAL2 Path Type mapping) . . .
2466
DCHQoSPri8ToAAL2PT (DCH QoSPri8 to AAL2 Path Type mapping) . . .
2468
DCHQoSPri9ToAAL2PT (DCH QoSPri9 to AAL2 Path Type mapping) . . .
2469
HSPAQoSPri0ToAAL2PT (HSPA QoSPri0 to AAL2 Path Type mapping) .
2471
HSPAQoSPri10ToAAL2PT (HSPA QoSPri10 to AAL2 Path Type mapping)
2473
HSPAQoSPri11ToAAL2PT (HSPA QoSPri11 to AAL2 Path Type mapping)
2475
HSPAQoSPri12ToAAL2PT (HSPA QoSPri12 to AAL2 Path Type mapping)
2477
HSPAQoSPri13ToAAL2PT (HSPA QoSPri13 to AAL2 Path Type mapping)
2479
HSPAQoSPri14ToAAL2PT (HSPA QoSPri14 to AAL2 Path Type mapping)
2481
HSPAQoSPri15ToAAL2PT (HSPA QoSPri15 to AAL2 Path Type mapping)
2483
HSPAQoSPri1ToAAL2PT (HSPA QoSPri1 to AAL2 Path Type mapping) .
2485
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
38.92
38.93
38.94
38.95
38.96
38.97
38.98
38.99
38.100
38.101
38.102
38.103
38.104
38.105
38.106
38.107
38.108
38.109
38.110
38.111
38.112
38.113
38.114
38.115
38.116
38.117
38.118
38.119
38.120
38.121
38.122
38.123
38.124
38.125
38.126
38.127
38.128
38.129
38.130
38.131
DN00211177
Issue 12B
HSPAQoSPri2ToAAL2PT (HSPA QoSPri2 to AAL2 Path Type mapping)
2487
HSPAQoSPri3ToAAL2PT (HSPA QoSPri3 to AAL2 Path Type mapping)
2489
HSPAQoSPri4ToAAL2PT (HSPA QoSPri4 to AAL2 Path Type mapping)
2491
HSPAQoSPri5ToAAL2PT (HSPA QoSPri5 to AAL2 Path Type mapping)
2493
HSPAQoSPri6ToAAL2PT (HSPA QoSPri6 to AAL2 Path Type mapping)
2495
HSPAQoSPri7ToAAL2PT (HSPA QoSPri7 to AAL2 Path Type mapping)
2497
HSPAQoSPri8ToAAL2PT (HSPA QoSPri8 to AAL2 Path Type mapping)
2499
HSPAQoSPri9ToAAL2PT (HSPA QoSPri9 to AAL2 Path Type mapping)
2501
PchFachRachToAAL2PT (PCH FACH to AAL2 Path Type mapping) 2503
SRBToAAL2PT (SRB to AAL2 Path Type mapping) . . . . . . . . . . . . . 2505
QosPriToDSCP (Qos Priority To DSCP) . . . . . . . . . . . . . . . . . . . . . . 2506
CSTrafficToDSCP (CS Traffic to DSCP mapping). . . . . . . . . . . . . . . 2509
DCHQoSPri0ToDSCP (DCH QoSPri0 to DSCP mapping) . . . . . . . . 2510
DCHQoSPri10ToDSCP (DCH QoSPri10 to DSCP mapping) . . . . . . 2511
DCHQoSPri11ToDSCP (DCH QoSPri11 to DSCP mapping) . . . . . . 2512
DCHQoSPri12ToDSCP (DCH QoSPri12 to DSCP mapping) . . . . . . 2513
DCHQoSPri13ToDSCP (DCH QoSPri13 to DSCP mapping) . . . . . . 2514
DCHQoSPri14ToDSCP (DCH QoSPri14 to DSCP mapping) . . . . . . 2516
DCHQoSPri15ToDSCP (DCH QoSPri15 to DSCP mapping) . . . . . . 2517
DCHQoSPri1ToDSCP (DCH QoSPri1 to DSCP mapping) . . . . . . . . 2518
DCHQoSPri2ToDSCP (DCH QoSPri2 to DSCP mapping) . . . . . . . . 2519
DCHQoSPri3ToDSCP (DCH QoSPri3 to DSCP mapping) . . . . . . . . 2520
DCHQoSPri4ToDSCP (DCH QoSPri4 to DSCP mapping) . . . . . . . . 2521
DCHQoSPri5ToDSCP (DCH QoSPri5 to DSCP mapping) . . . . . . . . 2522
DCHQoSPri6ToDSCP (DCH QoSPri6 to DSCP mapping) . . . . . . . . 2524
DCHQoSPri7ToDSCP (DCH QoSPri7 to DSCP mapping) . . . . . . . . 2525
DCHQoSPri8ToDSCP (DCH QoSPri8 to DSCP mapping) . . . . . . . . 2526
DCHQoSPri9ToDSCP (DCH QoSPri9 to DSCP mapping) . . . . . . . . 2527
HSPAQoSPri0ToDSCP (HSPA QoSPri0 to DSCP mapping) . . . . . . 2528
HSPAQoSPri10ToDSCP (HSPA QoSPri10 to DSCP mapping) . . . . 2529
HSPAQoSPri11ToDSCP (HSPA QoSPri11 to DSCP mapping) . . . . 2530
HSPAQoSPri12ToDSCP (HSPA QoSPri12 to DSCP mapping) . . . . 2532
HSPAQoSPri13ToDSCP (HSPA QoSPri13 to DSCP mapping) . . . . 2533
HSPAQoSPri14ToDSCP (HSPA QoSPri14 to DSCP mapping) . . . . 2534
HSPAQoSPri15ToDSCP (HSPA QoSPri15 to DSCP mapping) . . . . 2535
HSPAQoSPri1ToDSCP (HSPA QoSPri1 to DSCP mapping) . . . . . . 2536
HSPAQoSPri2ToDSCP (HSPA QoSPri2 to DSCP mapping) . . . . . . 2538
HSPAQoSPri3ToDSCP (HSPA QoSPri3 to DSCP mapping) . . . . . . 2539
HSPAQoSPri4ToDSCP (HSPA QoSPri4 to DSCP mapping) . . . . . . 2540
HSPAQoSPri5ToDSCP (HSPA QoSPri5 to DSCP mapping) . . . . . . 2541
Id:0900d805809d7397
71
WCDMA Radio Network Configuration Parameters
38.132
38.133
38.134
38.135
38.136
38.137
38.138
38.139
HSPAQoSPri6ToDSCP (HSPA QoSPri6 to DSCP mapping) . . . . . . . 2542
HSPAQoSPri7ToDSCP (HSPA QoSPri7 to DSCP mapping) . . . . . . . 2544
HSPAQoSPri8ToDSCP (HSPA QoSPri8 to DSCP mapping) . . . . . . . 2545
HSPAQoSPri9ToDSCP (HSPA QoSPri9 to DSCP mapping) . . . . . . . 2546
PchFachRachToDSCP (PCH FACH RACH to DSCP mapping) . . . . 2547
SRBToDSCP (SRB to DSCP mapping) . . . . . . . . . . . . . . . . . . . . . . . 2548
TQMChangeOrigin (TQM Change origin) . . . . . . . . . . . . . . . . . . . . . . 2549
TQMId (TQM object identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2550
39
39.1
VBTS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2552
ControllerIdPair (Neighbouring FD-BTS Identifier and Its SRNC Identifier)
2552
IHSPAadapterId (I-HSPA Adapter Identifier) . . . . . . . . . . . . . . . . . . . 2553
ServingRNCId (Serving RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2553
DediMeasRepPeriodCSdata (Dedicated Measurement Reporting Period
CS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2554
DediMeasRepPeriodPSdata (Dedicated Measurement Reporting Period
PS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2555
DedicatedMeasReportPeriod (Dedicated Measurement Reporting Period)
2556
HARQRVConfiguration (HARQ RV Configuration) . . . . . . . . . . . . . . . 2557
MeasFiltCoeff (Measurement filter coefficient) . . . . . . . . . . . . . . . . . . 2559
NodeBRABReconfigSupport (NodeB PS RAB reconfiguration Support) . .
2560
VBTSChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . . 2561
VBTSId (VBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2563
39.2
39.3
39.4
39.5
39.6
39.7
39.8
39.9
39.10
39.11
40
40.1
40.2
40.3
40.4
40.5
40.6
40.7
40.8
40.9
40.10
40.11
40.12
40.13
40.14
40.15
40.16
40.17
40.18
40.19
72
VCEL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2564
CSAMRModeSET (Configured CS AMR mode sets) . . . . . . . . . . . . . 2564
CSAMRModeSETWB (Configured CS WAMR mode sets) . . . . . . . . 2565
DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . . 2567
EDCHMinimumSetETFCI (E-DCH minimum set E-TFCI). . . . . . . . . . 2568
EbNoSetIdentifier (Eb/No parameter set identifier). . . . . . . . . . . . . . . 2569
FastActOfTargetServCell (Faster Activation Of Target Serving Cell) . 2570
FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . . 2571
HHoMaxAllowedBitrateDL (Maximum allowed DL user bit rate in HHO) . .
2573
HHoMaxAllowedBitrateUL (Maximum allowed UL user bit rate in HHO) . .
2574
HSDPAFmcgIdentifier (HSDPA FMCG identifier) . . . . . . . . . . . . . . . . 2575
HSDPAFmciIdentifier (HSDPA FMCI identifier) . . . . . . . . . . . . . . . . . 2576
HSDPAFmcsIdentifier (HSDPA FMCS identifier) . . . . . . . . . . . . . . . . 2577
HSDPAHopsIdentifier (HSDPA HOPS identifier) . . . . . . . . . . . . . . . . 2578
HSDPAenabled (HSDPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2579
HSPAFmcsIdentifier (HSPA FMCS identifier). . . . . . . . . . . . . . . . . . . 2581
HSPASCCSpecificATO (HSPA SCC Specific ATO Value). . . . . . . . . 2582
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay) . 2583
HSUPAEnabled (HSUPA enabled). . . . . . . . . . . . . . . . . . . . . . . . . . . 2584
InitialBitRateDL (Initial bit rate in downlink). . . . . . . . . . . . . . . . . . . . . 2585
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
40.20
40.21
40.22
40.23
40.24
40.25
40.26
40.27
40.28
40.29
40.30
40.31
40.32
40.33
40.34
40.35
40.36
40.37
40.38
40.39
40.40
40.41
40.42
40.43
40.44
40.45
40.46
40.47
40.48
40.49
40.50
40.51
40.52
40.53
41
41.1
41.2
DN00211177
Issue 12B
InitialBitRateUL (Initial bit rate in uplink) . . . . . . . . . . . . . . . . . . . . . . 2587
LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2589
MaxBitRateDLPSNRT (Maximum downlink bit rate for PS domain NRT data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2590
MaxBitRateULPSNRT (Maximum uplink bit rate for PS domain NRT data)
2591
MaxTotalUplinkSymbolRate (Maximum total uplink symbol rate) . . . 2593
MinAllowedBitRateDL (Minimum allowed bit rate in downlink) . . . . . 2594
MinAllowedBitRateUL (Minimum allowed bit rate in uplink). . . . . . . . 2595
NrtFmcgIdentifier (NRT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . 2597
NrtFmciIdentifier (NRT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2598
NrtFmcsIdentifier (NRT FMCS Identifier). . . . . . . . . . . . . . . . . . . . . . 2599
NrtHopgIdentifier (NRT HOPG Identifier). . . . . . . . . . . . . . . . . . . . . . 2600
NrtHopiIdentifier (NRT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2601
NrtHopsIdentifier (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . 2602
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2603
PtxOffsetHSSCCH (The power offset of the HS-SCCH) . . . . . . . . . . 2604
RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2605
RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for AMR multi-service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2606
RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for AMR multi-service)
2608
RTwithHSDPAFmciIdentifier (HSDPA FMCI identifier for AMR multi-service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2609
RTwithHSDPAFmcsIdentifier (HSDPA FMCS identifier for AMR multi-service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2610
RTwithHSDPAHopsIdentifier (HSDPA HOPS identifier for AMR multi-service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2611
RelocComm_in_InterRNC_HHO (Usage of Relocation Commit procedure
in inter RNC HHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2612
RtFmcgIdentifier (RT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2614
RtFmciIdentifier (RT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 2615
RtFmcsIdentifier (RT FMCS Identifier). . . . . . . . . . . . . . . . . . . . . . . . 2616
RtHopgIdentifier (RT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2616
RtHopiIdentifier (RT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 2617
RtHopsIdentifier (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2618
RxDivIndicator (Rx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . 2619
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . 2620
SRBHopsIdentifier (SRB HOPS Identifier). . . . . . . . . . . . . . . . . . . . . 2621
VCELChangeOrigin (Change Origin). . . . . . . . . . . . . . . . . . . . . . . . . 2622
VCELId (VCEL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2624
WACSetIdentifier (WAC Parameter Set Identifier). . . . . . . . . . . . . . . 2624
WAC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2626
DCHUtilRelAveWin (Window size for the release throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2626
DCHUtilRelThrDL (Threshold for the downlink DCH release measurement)
2627
Id:0900d805809d7397
73
WCDMA Radio Network Configuration Parameters
41.3
41.4
41.5
41.6
41.7
41.8
41.9
41.10
41.11
41.12
41.13
41.14
41.15
41.16
41.17
41.18
41.19
41.20
41.21
41.22
41.23
41.24
41.25
41.26
41.27
41.28
41.29
74
DCHUtilRelThrUL (Threshold for the uplink DCH release measurement) .
2630
DCHUtilRelTimeToTrigger (Time to trigger for the release throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2632
EDCHMACdFlowThroughputAveWin (Window size of E-DCH MAC-d flow
throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2633
EDCHMACdFlowThroughputRelThr (Low throughput threshold of the EDCH MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2634
EDCHMACdFlowThroughputTimetoTrigger (Low throughput time to trigger
of the E-DCH MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2635
HSDPAInitialBRULStrNRT (Initial bitrate for HSDPA UL DCH for NRT with
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2636
HSDPAMaxBitrateUL (Maximum bit rate for HSDPA UL DCH return channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2638
HSDPAMinBRULStrNRT (Min bitrate for HSDPA UL DCH for NRT with
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2639
HSDPAinitialBitrateUL (Initial bitrate for HSDPA associated UL DCH) . . .
2641
HSDPAminAllowedBitrateUL (Minimum bitrate for HSDPA associated UL
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2642
InactCPCBatOptT (Inactive CPC user with battery optimization timer) . . .
2643
InactCPCNoBatOptT (Inactive CPC user without battery optimization timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2646
InactHSRACH (Inactive HS-RACH capable UE) . . . . . . . . . . . . . . . . 2652
InactNonCPCBatOptT (Inactive nonCPC user with battery optimization
timer). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2653
InactNonCPCNoBatOptT (Inactive nonCPC user without battery optimization timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2659
InactivityTimerDownlinkDCH (Inactivity timer for downlink DCH) . . . . 2665
InactivityTimerDownlinkDCH128 (Inactivity timer for downlink 128kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2666
InactivityTimerDownlinkDCH16 (Inactivity timer for downlink 16kbps DCH)
2667
InactivityTimerDownlinkDCH256 (Inactivity timer for downlink 256kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2668
InactivityTimerDownlinkDCH32 (Inactivity timer for downlink 32kbps DCH)
2669
InactivityTimerDownlinkDCH320 (Inactivity timer for downlink 320kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2670
InactivityTimerDownlinkDCH384 (Inactivity timer for downlink 384kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2671
InactivityTimerDownlinkDCH64 (Inactivity timer for downlink 64kbps DCH)
2672
InactivityTimerDownlinkDCH8 (Inactivity timer for downlink 8kbps DCH) .
2673
InactivityTimerUplinkDCH (Inactivity timer for uplink DCH) . . . . . . . . 2674
InactivityTimerUplinkDCH128 (Inactivity timer for uplink 128kbps DCH) . .
2676
InactivityTimerUplinkDCH16 (Inactivity timer for uplink 16kbps DCH) 2677
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
41.30
41.55
41.56
41.57
41.58
41.59
InactivityTimerUplinkDCH256 (Inactivity timer for uplink 256kbps DCH). .
2678
InactivityTimerUplinkDCH32 (Inactivity timer for uplink 32kbps DCH) 2679
InactivityTimerUplinkDCH320 (Inactivity timer for uplink 320kbps DCH). .
2680
InactivityTimerUplinkDCH384 (Inactivity timer for uplink 384kbps DCH). .
2681
InactivityTimerUplinkDCH64 (Inactivity timer for uplink 64kbps DCH) 2682
InactivityTimerUplinkDCH8 (Inactivity timer for uplink 8kbps DCH). . 2683
MACdflowthroughputAveWin (Window size of the MAC-d flow throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2684
MACdflowutilRelThr (Low utilisation threshold of the MAC-d flow) . . 2685
MACdflowutilTimetoTrigger (Low utilization time to trigger of the MAC-d
flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2686
MSActivitySupervision (Time supervision of user inactivity (for NRT RBs))
2687
PrxNoiseMaxTuneAbsolute (Absolute limit in uplink noise autotuning) . . .
2689
TrafVolPendingTimeDL (Downlink traffic volume measurement pending
time after trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2690
TrafVolPendingTimeUL (Uplink traffic volume measurement pending time
after trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2692
TrafVolThresholdULLow (Uplink traffic volume measurement low threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2694
UL_DL_activation_timer (UL/DL activation timer) . . . . . . . . . . . . . . . 2696
WACChangeOrigin (WAC Change origin) . . . . . . . . . . . . . . . . . . . . . 2696
WACId (WAC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2698
WaitTimeRRC (Wait time in RRC connection request rejection) . . . . 2699
WaitTimeRRCbackground (RRC wait time for background causes) 2700
WaitTimeRRCconversational (RRC wait time for conversational causes)
2701
WaitTimeRRCemergency (RRC wait time for emergency causes) . 2702
WaitTimeRRChighPrioritySignalling (RRC wait time for high priority signalling causes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2703
WaitTimeRRCinterRATreselection (RRC wait time for inter-RAT re-selection causes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2704
WaitTimeRRCinteractive (RRC wait time for interactive causes) . . 2705
WaitTimeRRClowPrioritySignalling (RRC wait time for low priority signalling causes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2707
WaitTimeRRCother (RRC wait time for other causes) . . . . . . . . . . . 2708
WaitTimeRRCregistration (RRC wait time for registration causes) . 2709
WaitTimeRRCstreaming (RRC wait time for streaming causes) . . . 2710
WaitTimeRRCsubscribed (RRC wait time for subscribed causes) . 2711
WaitTimeRRCunknown (RRC wait time for unknown causes) . . . . . 2712
42
42.1
42.2
42.3
42.4
WANE Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2713
AuthorisedNetworkId (Authorised Network Identifier) . . . . . . . . . . . . 2713
AuthorisedNetworkPLMN (Authorised Network PLMN). . . . . . . . . . . 2714
AuthorisedNetworkMCC (Authorised Network Mobile Country Code) 2715
AuthorisedNetworkMNC (Authorised Network Mobile Network Code) 2716
41.31
41.32
41.33
41.34
41.35
41.36
41.37
41.38
41.39
41.40
41.41
41.42
41.43
41.44
41.45
41.46
41.47
41.48
41.49
41.50
41.51
41.52
41.53
41.54
DN00211177
Issue 12B
Id:0900d805809d7397
75
WCDMA Radio Network Configuration Parameters
42.5
42.6
42.7
42.8
43
43.1
43.2
43.3
43.4
43.5
43.6
43.7
43.8
43.9
43.10
43.11
43.12
43.13
43.14
43.15
43.16
43.17
43.18
43.19
43.20
43.21
43.22
43.23
43.24
43.25
43.26
43.27
43.28
43.29
43.30
43.31
76
AuthorisedNetworkMNClength (Authorised Network Mobile Network Code
Length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2717
Technology (Technology used in the Authorised Network) . . . . . . . . 2717
WANEChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 2718
WANEName (WANE Name). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2720
WBTS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2721
ATMInterfaceID (ATM interface identifier) . . . . . . . . . . . . . . . . . . . . . 2721
AdminWBTSState (Admin WBTS State). . . . . . . . . . . . . . . . . . . . . . . 2722
BTSAdditionalInfo (BTS Additional Information) . . . . . . . . . . . . . . . . . 2723
BTSFallbackEnabled (BTS Fallback enabled) . . . . . . . . . . . . . . . . . . 2724
BTSIPAddress (BTS O&M IP address). . . . . . . . . . . . . . . . . . . . . . . . 2725
BTSSupportForHSPACM (BTS Support For HSPA CM) . . . . . . . . . . 2726
BlindHOIntraBTSQCheck (Blind HO Intra BTS Quality Check) . . . . . 2727
BlindTFdetectionUsage (Blind transport format detection capability of BTS)
2728
BroadcastSIB15 (Broadcast SIB15) . . . . . . . . . . . . . . . . . . . . . . . . . . 2729
BroadcastSIB15_2 (Broadcast SIB15.2). . . . . . . . . . . . . . . . . . . . . . . 2730
BroadcastSIB15_3 (Broadcast SIB15.3). . . . . . . . . . . . . . . . . . . . . . . 2731
COCOId (Connection Configuration Identifier) . . . . . . . . . . . . . . . . . . 2732
DCHnumberRL (Number of DCHs per RL capability of BTS) . . . . . . . 2734
DCNLinkStatus (O&M DCN link status) . . . . . . . . . . . . . . . . . . . . . . . 2735
DCNSecurityStatus (O&M DCN secure link status) . . . . . . . . . . . . . . 2736
DLORLAveragingWindowSize (Tx power of radio link averaging window
size for DLO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2737
DSCPHigh (DSCP high priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2738
DSCPLow (DSCP Low priority). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2740
DSCPMedDCH (DSCP medium priority DCH) . . . . . . . . . . . . . . . . . . 2741
DSCPMedHSPA (DSCP Medium priority HSPA) . . . . . . . . . . . . . . . . 2742
DediMeasRepPeriodCSdata (Dedicated Measurement Reporting Period
CS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2743
DediMeasRepPeriodPSdata (Dedicated Measurement Reporting Period
PS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2744
DedicatedMeasReportPeriod (Dedicated Measurement Reporting Period)
2745
DelayThresholdMax (Maximum Threshold for HSUPA congestion handling
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2746
DelayThresholdMax2msTTI (Maximum Threshold for HSUPA congestion
delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2748
DelayThresholdMid (Middle Threshold value for HSUPA congestion delay)
2749
DelayThresholdMid2msTTI (Middle Threshold for HSUPA congestion delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2750
DelayThresholdMin (Minimum Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2751
DelayThresholdMin2msTTI (Minimum Threshold for HSUPA congestion
delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2752
HARQRVConfiguration (HARQ RV Configuration) . . . . . . . . . . . . . . . 2754
HSDPA14MbpsPerUser (HSDPA14MbpsPerUser) . . . . . . . . . . . . . . 2755
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
43.32
43.33
43.34
43.35
43.36
43.37
43.38
43.39
43.40
43.41
43.42
43.43
43.44
43.45
43.46
43.47
43.48
43.49
43.50
43.51
43.52
43.53
43.54
43.55
43.56
43.57
43.58
43.59
43.60
43.61
43.62
43.63
43.64
43.65
43.66
43.67
43.68
43.69
43.70
43.71
DN00211177
Issue 12B
HSDPACCEnabled (HSDPA Congestion Control activation) . . . . . . 2756
HSDPAIurWeight (HSDPA Iur Weight) . . . . . . . . . . . . . . . . . . . . . . . 2758
HSDPAOperIdWeightPair (HSDPA Operator Identifier Weight Pair). 2759
HSDPAOperatorId (HSDPA Operator Identifier) . . . . . . . . . . . . . . . . 2760
HSDPAOperatorWeight (HSDPA Operator Weight) . . . . . . . . . . . . . 2761
HSDPAULCToDSCP (HSDPA UL FP Control traffic to DSCP mapping) .
2763
HSDPAUserHysterisis (HSDPA User Hysterisis) . . . . . . . . . . . . . . . 2764
HSDPAUserThreshold (HSDPA User Threshold) . . . . . . . . . . . . . . . 2765
HSUPACCEnabled (HSUPA Congestion Control activation) . . . . . . 2766
HSUPADLCToDSCP (HSUPA DL FP Control traffic to DSCP mapping) .
2767
HSUPAXUsersEnabled (HSUPA x users enabled) . . . . . . . . . . . . . . 2768
ICREnabled (ICR Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2771
IPBasedRouteIdIub (IP Based Route Id Iub) . . . . . . . . . . . . . . . . . . . 2772
IPBasedRouteIdIub2 (IP Based Route Id Iub 2) . . . . . . . . . . . . . . . . 2773
IPBasedRouteIdIub3 (IP Based Route Id Iub 3) . . . . . . . . . . . . . . . . 2774
IPBasedRouteIdIub4 (IP Based Route Id Iub 4) . . . . . . . . . . . . . . . . 2776
IPNBId (IPNB object identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2777
InactCACThresholdATM (Inactive users CAC Threshold for ATM) . . 2779
InactCACThresholdIP (Inactive users CAC Threshold for IP) . . . . . . 2780
InactUsersCIDThreshold (Inactive users Connection ID Threshold) . 2781
IntelligentSDPrioHO (Priorized Handover Type in Intelligent Shutdown) .
2782
IubTransportFallback (Iub Transport Fallback Mapping) . . . . . . . . . . 2783
IubTransportMedia (Iub Transport Media Selection) . . . . . . . . . . . . . 2785
IubTransportSharing (Iub Transport Sharing activation) . . . . . . . . . . 2788
LoadControlPeriodPS (PS load control period) . . . . . . . . . . . . . . . . . 2789
MDCBufferingTime (MDC Buffering Time) . . . . . . . . . . . . . . . . . . . . 2790
MaxDCHuserRateRLDL (Max DL user rate per RL) . . . . . . . . . . . . . 2791
MaxDCHuserRateRLUL (Max UL user rate per RL) . . . . . . . . . . . . . 2792
MaxFPDLFrameSizeIub (Maximum FP downlink frame size Iub) . . . 2793
MaxNumberEDCHLCG (Maximum number of E-DCHs in the local cell
group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2795
MeasFiltCoeff (Measurement filter coefficient) . . . . . . . . . . . . . . . . . 2796
MinUDPPortIub (Minimum UDP port value for the Iub) . . . . . . . . . . . 2798
NBAPCommMode (NBAP Communication Mode) . . . . . . . . . . . . . . 2799
NESWVersion (NE-SW-Version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2800
NEType (NE-type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2801
NbrOfOverbookedHSDPAUsers (Number of overbooked HSDPA users).
2802
NodeBRABReconfigSupport (NodeB PS RAB reconfiguration Support). .
2803
OverbookingSwitch (Overbooking Switch). . . . . . . . . . . . . . . . . . . . . 2804
PDUSize656WithHSDSCH (Usage of RLC PDU size 656 with HS-DSCH)
2805
PSAveragingWindowSize (Load measurement averaging window size for
packet scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2807
Id:0900d805809d7397
77
WCDMA Radio Network Configuration Parameters
43.72
43.73
43.74
43.75
43.76
43.77
43.78
43.79
43.80
43.81
43.82
43.83
43.84
43.85
43.86
43.87
43.88
43.89
43.90
43.91
43.92
43.93
43.94
43.95
43.96
43.97
43.98
43.99
43.100
43.101
78
PSRLAveragingWindowSize (Tx power of radio link averaging window size
for PS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2808
PWSMAVTrafficVERLogic (Traffic verification logic in PWSM cell activation process) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2810
PWSMEnableWakeUpTime (Enable cell activation based on time of day)
2811
PWSMInUse (The PWSM usage in BTS) . . . . . . . . . . . . . . . . . . . . . . 2812
PWSMRemCellSDBeginHour (PWSM Shutdown Time Begin Hour for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2814
PWSMRemCellSDBeginMin (PWSM Shutdown Time Begin Minute for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2815
PWSMRemCellSDEndHour (PWSM Shutdown Time End Hour for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2816
PWSMRemCellSDEndMin (PWSM Shutdown Time End Minute for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2817
PWSMShutdownBeginHour (Hour when the cell shutdown window starts)
2818
PWSMShutdownBeginMin (Minute when the cell shutdown window starts)
2819
PWSMShutdownEndHour (Hour when the cell shutdown window ends) . .
2820
PWSMShutdownEndMin (Minute when the cell shutdown window ends) .
2822
PWSMWeekday (Weekend for shutdown) . . . . . . . . . . . . . . . . . . . . . 2823
ProbabilityFactorMax (ProbabilityFactor for Congestion Indication sending)
2824
ProbabilityFactorMax2msTTI (ProbabilityFactor for Congestion Indication
sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2825
PrxAlpha (Type of measurement filter for uplink total received power) . . .
2826
PrxMeasAveWindow (Number of frames to be used averaging in PrxTotal
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2827
PrxTargetPSAdjustPeriod (PS target tune period in HSPA-DCH interference sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2828
PtxAlpha (Type of measurement filter for downlink total transmitted power)
2829
PtxDPCHmax (DPCH downlink transmission power maximum value) 2830
PtxDPCHmin (DPCH downlink transmission power minimum value) . 2832
PtxMeasAveWindow (Number of frames to be used averaging in PtxTotal
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2833
R99OperIdWeightPair (R99 Operator Identifier Weight Pair) . . . . . . . 2834
R99OperatorId (R99 Operator Identifier) . . . . . . . . . . . . . . . . . . . . . . 2835
R99OperatorWeight (R99 Operator Weight). . . . . . . . . . . . . . . . . . . . 2836
RACHloadIndicationPeriod (RACH load indication period). . . . . . . . . 2838
RFSharingState (RF Sharing State) . . . . . . . . . . . . . . . . . . . . . . . . . . 2839
RRIndPeriod (Radio Resource Indication Period) . . . . . . . . . . . . . . . 2840
RRMULDCHActivityFactor (Average UL DCH data rates for the radio bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2842
RRMULActivityFactorPTT (Average relative UL data rate for RBs of PTT)
2843
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
43.102
43.103
43.104
43.105
43.106
43.107
43.108
43.109
43.110
43.111
43.112
43.113
43.114
43.115
43.116
43.117
43.118
43.119
43.120
43.121
43.122
43.123
43.124
43.125
43.126
43.127
43.128
43.129
43.130
43.131
43.132
43.133
43.134
DN00211177
Issue 12B
RRMULDCHActivityFactorCSAMR (Average UL DCH data rate for RBs of
CS AMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2844
RRMULDCHActivityFactorCSNTData (Average UL DCH data rate for RB
of CS NT-data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2845
RRMULDCHActivityFactorCSTData (Average UL DCH data rate for RB of
CS T-data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2846
RRMULDCHActivityFactorPSBackgr (Average UL DCH data rate for RB of
PS background RAB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2847
RRMULDCHActivityFactorPSStream (Average UL DCH data rate for RB of
PS Streaming RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2848
RRMULDCHActivityFactorPSTHP1 (Average UL DCH data rate for RB of
PS THP1 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2849
RRMULDCHActivityFactorPSTHP2 (Average UL DCH data rate for RB of
PS THP2 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2850
RRMULDCHActivityFactorPSTHP3 (Average UL DCH data rate for RB of
PS THP3 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2851
RRMULDCHActivityFactorSRB (Average UL DCH data rate for SRB) . . .
2852
ReleaseTimerForSharedHSDPAallocation (Release timer for shared HSDPA allocation). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2853
SatelliteIubUsage (Satellite Iub Usage) . . . . . . . . . . . . . . . . . . . . . . . 2854
SchedulingPeriod (Scheduling period). . . . . . . . . . . . . . . . . . . . . . . . 2856
SharedHSDPAVCCSelectionMethod (Shared HSDPA AAL2 VCC selection method) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2857
SharedHSDPAallocation (Shared HSDPA AAL2 allocation) . . . . . . . 2858
TQMId (TQM object identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2859
TQMId2 (TQM Object Identifier 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2861
TQMId3 (TQM Object Identifier 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2862
TQMId4 (TQM Object Identifier 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2864
TargetId (Network Element Target Identifier). . . . . . . . . . . . . . . . . . . 2865
ToAWEOffsetNRTDCHIP (ToAWE Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2866
ToAWEOffsetRTDCHIP (ToAWE Offset for RT DCH connections over IP)
2867
ToAWSOffsetNRTDCHIP (ToAWS Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2869
ToAWSOffsetRTDCHIP (ToAWS Offset for RT DCH connections over IP)
2870
VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2871
VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2872
WBTSChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . 2873
WBTSId (WBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2875
WBTSName (WCDMA BTS name) . . . . . . . . . . . . . . . . . . . . . . . . . . 2875
WBTSSWBuildId (WBTS SW build identifier) . . . . . . . . . . . . . . . . . . 2876
WinACRABsetupDL (DL measurement averaging window for AC) . . 2877
WinACRABsetupUL (UL measurement averaging window for AC) . . 2878
WinLCHSDPA (PtxnonHSPA averaging window size for LC) . . . . . . 2879
WinLCHSUPA (Non E-DCH ST interference averaging window size for LC)
2881
Id:0900d805809d7397
79
WCDMA Radio Network Configuration Parameters
44
44.1
44.2
44.3
44.4
44.5
44.6
44.7
44.8
44.9
44.10
44.11
44.12
44.13
44.14
44.15
44.16
44.17
44.18
44.19
44.20
44.21
44.22
44.23
44.24
44.25
44.26
44.27
44.28
44.29
44.30
44.31
44.32
44.33
44.34
44.35
44.36
44.37
44.38
44.39
44.40
80
WCEL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2883
ACBarredList (Access Class Barred list) . . . . . . . . . . . . . . . . . . . . . . 2883
AICHTraTime (AICH Transmission Timing) . . . . . . . . . . . . . . . . . . . . 2885
AMROverSC (AMROverSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2886
AMROverTransmission (AMROverTransmission) . . . . . . . . . . . . . . . 2887
AMROverTxNC (AMROverTxNC). . . . . . . . . . . . . . . . . . . . . . . . . . . . 2888
AMROverTxNonHSPA (AMROverTxNonHSPA) . . . . . . . . . . . . . . . . 2889
AMROverTxTotal (AMROverTxTotal) . . . . . . . . . . . . . . . . . . . . . . . . . 2890
AMRSF (AMRSF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2891
AMRTargetSC (AMRTargetSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2892
AMRTargetTransmission (AMRTargetTransmission) . . . . . . . . . . . . . 2893
AMRTargetTxNC (AMRTargetTxNC) . . . . . . . . . . . . . . . . . . . . . . . . . 2894
AMRTargetTxNonHSPA (AMRTargetTxNonHSPA) . . . . . . . . . . . . . . 2895
AMRTargetTxTotal (AMRTargetTxTotal) . . . . . . . . . . . . . . . . . . . . . . 2896
AMRUnderSC (AMRUnderSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2897
AMRUnderTransmission (AMRUnderTransmission) . . . . . . . . . . . . . 2899
AMRUnderTxNC (AMRUnderTxNC). . . . . . . . . . . . . . . . . . . . . . . . . . 2900
AMRUnderTxNonHSPA (AMRUnderTxNonHSPA) . . . . . . . . . . . . . . 2901
AMRUnderTxTotal (AMRUnderTxTotal) . . . . . . . . . . . . . . . . . . . . . . . 2902
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA). . . 2903
AbsPrioCellReselec (Absolute priority level for cell reselection). . . . . 2904
ActivationTimeOffset (Offset for activation time). . . . . . . . . . . . . . . . . 2905
AdminCellState (Administrative Cell State). . . . . . . . . . . . . . . . . . . . . 2907
AdminPICState (Admin PIC state) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2908
AllowedPreambleSignatures (Allowed preamble signatures) . . . . . . . 2909
AllowedRACHSubChannels (Allowed RACH subchannels) . . . . . . . . 2911
AltScramblingCodeCM (Compressed Mode: Alternative scrambling code)
2912
AmpliRatioOptHSRACH (HS-RACH amplitude ratio optimized for low/high
bit rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2913
AppAwareRANCapability (Application Aware RAN Capability) . . . . . 2914
AppAwareRANEnabled (Application Aware RAN Enabled) . . . . . . . . 2915
AssignedPICPool (Cell assigned to PIC pool) . . . . . . . . . . . . . . . . . . 2916
AutoACDSACRestriction (Domain Specific Access Class Restriction). . . .
2918
AutoACRPrxTotalAvgWs (Automatic Access Class window size for averaging PrxTotal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2920
AutoACResULOLThr (Automatic Access Class Restriction Uplink Overload Threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2922
BlindHOEcNoThrTarget (Blind HO EcNo threshold for target cell) . . . 2923
BlindHORSCPThrTarget (Blind HO RSCP threshold for target cell) . 2924
CCHSetupEnabled (RRC Connection Setup on CCH Enabled). . . . . 2925
CIRForFDPCH (Carrier to interference ratio for F-DPCH) . . . . . . . . . 2926
CId (Cell identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2927
CPCEnabled (CPC enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2928
CPICHEcNoSRBMapRRC (CPICH Ec/No thr for SRB mapping in RRC setup). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2929
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
44.41
44.42
44.43
44.44
44.45
44.46
44.47
44.48
44.49
44.50
44.51
44.52
44.53
44.54
44.55
44.56
44.57
44.58
44.59
44.60
44.61
44.62
44.63
44.64
44.65
44.66
44.67
44.68
44.69
44.70
44.71
44.72
44.73
44.74
44.75
44.76
44.77
44.78
DN00211177
Issue 12B
CPICHRSCPSRBMapRRC (CPICH RSCP thr for SRB mapping in RRC
setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2930
CPICHtoRefRABoffset (Offset of the P-CPICH and reference service powers). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2932
CSAMRModeSET (Configured CS AMR mode sets) . . . . . . . . . . . . 2933
CSAMRModeSETWB (Configured CS WAMR mode sets) . . . . . . . . 2935
CSGroupId (Restriction Group Id for Circuit Switched Acces). . . . . . 2936
CTCHCapaHighPri (CTCH capacity for High Priority CBS messages) . . .
2937
CUCEcNoThreshold (CPICH Ec/No Threshold Value For CUC Usage) . .
2938
CUCRSCPThreshold (CPICH RSCP Threshold Value For CUC Usage) .
2940
CableLoss (Cable Loss). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2942
CellAdditionalInfo (Cell Additional Information) . . . . . . . . . . . . . . . . . 2943
CellBarred (Cell Barred). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2944
CellRange (Cell range) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2945
CellSelQualMeas (Measurement to be used as quality measure). . . 2947
CellWeightForHSDPALayering (Cell weight for HSDPA layering). . . 2948
Cell_Reserved (Cell Reserved for operator use) . . . . . . . . . . . . . . . . 2949
CodeTreeOptTimer (Code tree optimisation timer) . . . . . . . . . . . . . . 2951
CodeTreeOptimisation (Code tree optimisation) . . . . . . . . . . . . . . . . 2951
CodeTreeOptimisationGuardTime (Code Tree Optimisation Guard Time)
2952
CodeTreeUsage (Code Tree Usage). . . . . . . . . . . . . . . . . . . . . . . . . 2953
DBandHSDPAEnabled (Dual Band HSDPA Enabled). . . . . . . . . . . . 2954
DCellAndMIMOUsage (DC-HSDPA and MIMO Usage) . . . . . . . . . . 2956
DCellHSDPACapaHO (DC HSDPA Capability HO). . . . . . . . . . . . . . 2957
DCellHSDPAEnabled (DC HSDPA Enabled) . . . . . . . . . . . . . . . . . . 2959
DCellHSDPAFmcsId (DC HSDPA FMCS Identifier) . . . . . . . . . . . . . 2962
DLLoadStateTTT (DL loaded state time to trigger) . . . . . . . . . . . . . . 2963
DPCHOverHSPDSCHThreshold (NRT DPCH over HS-PDSCH code offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2965
DPCModeChangeSupport (DPC Mode Change Support) . . . . . . . . . 2966
DRRCprxMargin (Prx Margin for DRRC) . . . . . . . . . . . . . . . . . . . . . . 2967
DRRCprxOffset (Prx Offset for DRRC) . . . . . . . . . . . . . . . . . . . . . . . 2968
DRRCptxMargin (Ptx Margin for DRRC) . . . . . . . . . . . . . . . . . . . . . . 2969
DRRCptxOffset (Ptx Offset for DRRC) . . . . . . . . . . . . . . . . . . . . . . . 2970
DRXCycleHSFACH (Discontinuous Reception Cycle HS-FACH) . . . 2971
DRXInactiveTimerHSFACH (Inactivity Supervision Timer of HS-FACH for
DRX User ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2972
DRXInterruptHSDSCHData (DRX Interruption by HS-DSCH data). . 2973
DefMeasCtrlReading (Deferred Measurement Control Reading) . . . 2974
DeltaPrxMaxDown (Maximum uplink power decrease in packet scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2975
DeltaPrxMaxUp (Maximum uplink power increase in packet scheduling) .
2976
DeltaPtxMaxDown (Maximum downlink power decrease in packet scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2978
Id:0900d805809d7397
81
WCDMA Radio Network Configuration Parameters
44.79
44.80
44.81
44.82
44.83
44.84
44.85
44.86
44.87
44.88
44.89
44.90
44.91
44.92
44.93
44.94
44.95
44.96
44.97
44.98
44.99
44.100
44.101
44.102
44.103
44.104
44.105
44.106
44.107
44.108
44.109
44.110
44.111
44.112
44.113
44.114
44.115
44.116
82
DeltaPtxMaxUp (Maximum downlink power increase in packet scheduling)
2979
DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . . 2980
DirectedRRCEnabled (Directed RRC connection setup enabled) . . . 2981
DirectedRRCForHSDPALayerEnabled (Directed RRC connection setup
for HSDPA layer enabled). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2982
EDCHCapability (E-DCH Capability) . . . . . . . . . . . . . . . . . . . . . . . . . 2984
EDCHMinSetETFCIT0 (E-DCH minimum set E-TFCI 10 ms TTI table 0) .
2985
EDCHMinimumSetETFCI (E-DCH minimum set E-TFCI 10 ms TTI table 1)
2986
EDCHOpState (Operational E-DCH state) . . . . . . . . . . . . . . . . . . . . . 2987
EVAMCapability (EVAM capability) . . . . . . . . . . . . . . . . . . . . . . . . . . 2988
EVAMInUse (EVAM in use) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2989
EbNoSetIdentifier (Eb/No parameter set identifier). . . . . . . . . . . . . . . 2990
EvamDInit (Initial phase offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2991
EvamNumPhaseOffset (Phase offset amount) . . . . . . . . . . . . . . . . . . 2992
EvamTKeep (Keep time). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2993
EvamTSweep (Sweep time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2994
FDPCHCodeChangeEnabled (F-DPCH code change enabled). . . . . 2995
FDPCHEnabled (F-DPCH enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2996
FDPCHSetup (F-DPCH setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2997
FachLoadMarginCCH (Margin for FACH load for downlink channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2998
FachLoadThresholdCCH (Threshold for FACH load for downlink channel
type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2999
FastActOfTargetServCell (Faster Activation Of Target Serving Cell) . 3000
FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . . 3002
FastHSPAMobilityEnabled (Fast HSPA Mobility Enabled) . . . . . . . . . 3003
HCS_PRIO (HCS priority level for a cell) . . . . . . . . . . . . . . . . . . . . . . 3005
HHoMaxAllowedBitrateDL (Maximum allowed DL user bit rate in HHO) . .
3006
HHoMaxAllowedBitrateUL (Maximum allowed UL user bit rate in HHO) . .
3007
HSCapabilityHONumbUE (HSPA Capability Based Handover Max Number of UE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3009
HSCapabilityHOPeriod (HSPA Capability Based Handover Period) . 3010
HSDPA64QAMallowed (HSDPA 64 QAM allowed) . . . . . . . . . . . . . . 3011
HSDPA64UsersEnabled (HSDPA 64 users enabled). . . . . . . . . . . . . 3013
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No) 3015
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No) 3016
HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3017
HSDPAFmcgIdentifier (HSDPA FMCG identifier) . . . . . . . . . . . . . . . . 3019
HSDPAFmciIdentifier (HSDPA FMCI identifier) . . . . . . . . . . . . . . . . . 3020
HSDPAFmcsIdentifier (HSDPA FMCS identifier) . . . . . . . . . . . . . . . . 3021
HSDPALayeringCommonChEnabled (HSDPA layering for UEs in common
channels enabled). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3022
HSDPAMPO (HSDPA Measurement Power Offset) . . . . . . . . . . . . . . 3023
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
44.117
44.118
44.119
44.120
44.121
44.122
44.123
44.124
44.125
44.126
44.127
44.128
44.129
44.130
44.131
44.132
44.133
44.134
44.135
44.136
44.137
44.138
44.139
44.140
44.141
44.142
44.143
44.144
44.145
44.146
44.147
44.148
44.149
DN00211177
Issue 12B
HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3024
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3026
HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell)
3027
HSDPAcapability (HSDPA Capability) . . . . . . . . . . . . . . . . . . . . . . . . 3029
HSDPAenabled (HSDPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 3030
HSDSCHOpState (Operational HS-DSCH state) . . . . . . . . . . . . . . . 3032
HSFACHActTimeToTrigger (Time to trigger for activity measurement on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3033
HSFACHActivityAveWin (Window size of HS-DSCH MAC-d flow of PS RB
on HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3035
HSFACHActivityThr (Threshold of the HS-DSCH MAC-d flow of PS RB on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3036
HSFACHCapability (High Speed FACH Capability). . . . . . . . . . . . . . 3037
HSFACHDRXEnabled (UE DRX with High Speed Cell FACH Enabled) . .
3038
HSFACHEnabled (High Speed Cell_FACH DL Enabled) . . . . . . . . . 3039
HSFACHRABDRAEnabled (HSFACH direct resource allocation for NRT
HSPA RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3040
HSFACHRLCTimeToTrigger (Time to trigger for RLC measurement on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3041
HSFACHRel7ConSetupEC (HSFACH Rel7UE EstCause mapping in RRC
con setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3043
HSFACHRel8ConSetupEC (HSFACH Rel8UE EstCause mapping in RRC
con setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3045
HSFACHVolThrDL (DL traffic volume measurement threshold of HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3047
HSFACHVolThrDLPTT (DL traffic volume measurement threshold of HSFACH for PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3049
HSLoadStateHSDBRLimit (HSPA load state HSDPA bit rate limit). . 3050
HSLoadStateHSDOffset (HSPA load state HSDPA power Offset) . . 3051
HSLoadStateHSUBRLimit (HSPA load state E-DCH bit rate limit) . . 3052
HSLoadStateHSUOffset (HSPA load state HSUPA power Offset) . . 3053
HSLoadStateHSUResThr (HSPA Load State HSUPA Resource Threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3054
HSPA128UsersPerCell (HSPA 128 Users per Cell) . . . . . . . . . . . . . 3055
HSPA72UsersPerCell (HSPA 72 Users per Cell) . . . . . . . . . . . . . . . 3057
HSPACapaHO (HSPA Capability Based Handover) . . . . . . . . . . . . . 3059
HSPAFmcsIdentifier (HSPA FMCS identifier) . . . . . . . . . . . . . . . . . . 3061
HSPAQoSEnabled (HSPA QoS enabled) . . . . . . . . . . . . . . . . . . . . . 3062
HSPASCCSpecificATO (HSPA SCC Specific ATO Value) . . . . . . . . 3066
HSPDSCHCodeSet (HS-PDSCH code set). . . . . . . . . . . . . . . . . . . . 3067
HSPDSCHMarginSF128 (HS-PDSCH code upgrade margin for SF128
codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3069
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay). 3071
HSRACHActTimeToTrigger (Time to trigger for activity measurement on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3072
Id:0900d805809d7397
83
WCDMA Radio Network Configuration Parameters
44.150
44.151
44.152
44.153
44.154
44.155
44.156
44.157
44.158
44.159
44.160
44.161
44.162
44.163
44.164
44.165
44.166
44.167
44.168
44.169
44.170
44.171
44.172
44.173
44.174
44.175
44.176
44.177
44.178
44.179
44.180
44.181
84
HSRACHActivityAveWin (Window size of E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3074
HSRACHActivityThr (Threshold of the E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3075
HSRACHCapability (High Speed RACH Capability) . . . . . . . . . . . . . . 3076
HSRACHCommonEDCHRes (Number of Common E-DCH Resources for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3077
HSRACHEnabled (High Speed RACH Enabled) . . . . . . . . . . . . . . . . 3078
HSRACHExtendedAI (Use of Extended Acquisition Indicator HS-RACH) .
3079
HSRACHImplicitRelease (Common E-DCH implicit release for HS-RACH)
3080
HSRACHMPO (HS-RACH Measurement Power Offset) . . . . . . . . . . 3082
HSRACHMaxAllocTimeCCCH (Maximum E-DCH resource alloc time for
CCCH for HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3083
HSRACHMaxPeriodCollis (Max period for collision resolution phase for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3084
HSRACHMaxTotSymbolRate (Maximum total uplink symbol rate of the
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3085
HSRACHSubChannelNumber (Available Sub Channel Number for HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3086
HSRACHTimeToTrigger (Traffic volume measurement time to trigger of
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3088
HSRACHTransmisBackOff (Additional E-DCH transmission back off for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3090
HSRACHVolThrUL (UL traffic volume measurement threshold of HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3091
HSUPA16QAMAllowed (HSUPA 16QAM usage allowed in a cell). . . 3092
HSUPA2MSTTIEnabled (HSUPA 2 ms TTI enabled). . . . . . . . . . . . . 3093
HSUPAEnabled (HSUPA enabled). . . . . . . . . . . . . . . . . . . . . . . . . . . 3094
HSUPAUserLimit16QAM (HSUPA user limit for 16QAM usage) . . . . 3097
HappyBitDelayConHSRACH (Happy bit delay condition for HS-RACH) . .
3098
HspaMultiNrtRabSupport (HSPA multi NRT RAB Support) . . . . . . . . 3099
ICRCapability (ICR Capability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3100
IncomingLTEISHO (Incoming ISHO from LTE) . . . . . . . . . . . . . . . . . 3101
InitialBitRateDL (Initial bit rate in downlink). . . . . . . . . . . . . . . . . . . . . 3102
InitialBitRateUL (Initial bit rate in uplink) . . . . . . . . . . . . . . . . . . . . . . . 3104
InterFreqScaleTresel (Scaling factor of Treselection in inter-frequency
case) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3105
InterRATScaleTresel (Scaling factor of Treselection in inter-RAT case) . .
3106
IntraFreq_Cell_Reselect_Ind (Intra-frequency cell re-selection indicator) .
3108
KforCTCH (CBS frame offset (K)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3109
LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3110
LHOCapaReqRejRateDL (Load HO DL NRT capacity request rejection
rate). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3112
LHOCapaReqRejRateUL (Load HO UL NRT capacity request rejection
rate). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3114
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
44.182
44.183
44.184
44.185
44.186
44.187
44.188
44.189
44.190
44.191
44.192
44.193
44.194
44.195
44.196
44.197
44.198
44.199
44.200
44.201
44.202
44.203
44.204
44.205
44.206
44.207
44.208
44.209
44.210
44.211
DN00211177
Issue 12B
LHODelayOFFCapaReqRejRate (Delay to broadcast NRT load based HO
state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3115
LHODelayOFFHardBlocking (Delay to broadcast hard blocking load based
HO state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3116
LHODelayOFFInterference (Delay to broadcast interference load based
HO state over) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3117
LHODelayOFFResRateSC (Delay to broadcast DL SC load based HO
state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3119
LHOHardBlockingBaseLoad (Load HO hard blocking base load) . . . 3120
LHOHardBlockingRatio (Load HO hard blocking ratio) . . . . . . . . . . . 3121
LHOHystTimeCapaReqRejRate (Hysteresis for NRT load measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3122
LHOHystTimeHardBlocking (Hysteresis for hard blocking measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3123
LHOHystTimeInterference (Hysteresis for interference measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3124
LHOHystTimeResRateSC (Hysteresis for DL SC measurement of LHO) .
3125
LHONRTTrafficBaseLoad (Load HO NRT traffic base load) . . . . . . . 3127
LHONumbUEInterFreq (Number of UEs in inter-frequency load HO ) 3128
LHONumbUEInterRAT (Number of UEs in inter-RAT load HO ) . . . . 3129
LHOPwrOffsetDL (Load HO DL power offset) . . . . . . . . . . . . . . . . . . 3130
LHOPwrOffsetUL (Load HO UL power offset) . . . . . . . . . . . . . . . . . . 3131
LHOResRateSC (Load HO reservation rate of DL spreading codes) 3132
LHOWinSizeOFFCapaReqRejRate (Window size for NRT load measurement to stop LHOs ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3134
LHOWinSizeOFFHardBlocking (Window size for hard blocking measurement to stop LHOs ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3135
LHOWinSizeOFFInterference (Window size for interference measurement
to stop LHOs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3136
LHOWinSizeOFFResRateSC (Window size for DL SC reservation rate
measurement to stop LHOs ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3137
LHOWinSizeONCapaReqRejRate (Window size for NRT load measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3138
LHOWinSizeONHardBlocking (Window size for hard blocking measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3139
LHOWinSizeONInterference (Window size for interference measurement
to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3140
LHOWinSizeONResRateSC (Window size for DL SC reservation rate
measurement to start LHOs ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3142
LTECellReselection (LTE Cell Reselection) . . . . . . . . . . . . . . . . . . . 3143
LayeringRRCConnRelTargFreq (Target frequency for layering in RRC
Connection Release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3144
TargetFrequency (Target frequency) . . . . . . . . . . . . . . . . . . . . . . . . . 3145
LayeringRRCRelEnabled (Layering in RRC Connection Release Enabled)
3146
LcrId (Local cell resource identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 3147
LoadBasedCPICHEcNoSRBHSPA (Load Based CPICH EcNo for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3148
Id:0900d805809d7397
85
WCDMA Radio Network Configuration Parameters
44.212
44.213
44.214
44.215
44.216
44.217
44.218
44.219
44.220
44.221
44.222
44.223
44.224
44.225
44.226
44.227
44.228
44.229
44.230
44.231
44.232
44.233
44.234
44.235
44.236
44.237
44.238
44.239
44.240
44.241
44.242
44.243
44.244
86
LoadBasedCPICHEcNoThreEDCH2MS (Load Based CPICH EcNo
Threshold for E-DCH TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3149
MBLBInactivityEnabled (MBLB in Inactivity Enabled). . . . . . . . . . . . . 3150
MBLBLoadInfoDistr (MBLB Load Information Distribution). . . . . . . . . 3151
MBLBMobilityEnabled (MBLB in Mobility Enabled) . . . . . . . . . . . . . . 3153
MBLBRABSetupEnabled (MBLB in RAB Setup Enabled) . . . . . . . . . 3154
MBLBRABSetupMultiRAB (MBLB in RAB Setup for Multi RAB) . . . . 3155
MBLBStateTransEnabled (MBLB in State Transition Enabled) . . . . . 3156
MEHHSDPAUserNbrCQI (HSDPA CQI user number for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3158
MEHHSUPAUserNbr2msTTI (HSUPA E-DCH 2 ms TTI user number for
the Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3159
MEHLoadStateTtT (Load state time-to-trigger for the Mass Event Handler)
3160
MEHMaxHSUPAUsers (Temporary max number of HSUPA users for the
Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3162
MEHQueueThreshold (Scheduling queue threshold for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3163
MEHULLHSDPAUALimit (UL load based HSDPA user amount limit for the
MEH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3165
MHA (MHA used) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3167
MIMOEnabled (MIMO Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3169
MIMOHSDPACapaHO (MIMO HSDPA Capability Handover) . . . . . . 3171
MIMOWith64QAMUsage (MIMO with 64QAM usage) . . . . . . . . . . . . 3172
MassEventHandler (Mass Event Handler functions) . . . . . . . . . . . . . 3173
MaxBitRateDLPSNRT (Maximum downlink bit rate for PS domain NRT data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3175
MaxBitRateULPSNRT (Maximum uplink bit rate for PS domain NRT data)
3177
MaxCodeReleases (Max Code Releases) . . . . . . . . . . . . . . . . . . . . . 3178
MaxDLPowerCapability (Maximum DL Power Capability) . . . . . . . . . 3179
MaxIncrInterferenceUL (Max increment in the received wide band interference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3180
MaxNbrOfHSSCCHCodes (Maximum number of HS-SCCH codes) . 3182
MaxNumbHSDPAUsersS (Max number HSDPA users per MAChs/ehs
scheduler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3183
MaxNumbHSDSCHMACdFS (Max number HSDSCH MACd flows per
MAChs/ehs scheduler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3184
MaxNumberEDCHCell (Maximum number of E-DCHs in the cell) . . . 3186
MaxNumberHSDPAUsers (Maximum number of HSDPA users) . . . . 3188
MaxNumberHSDSCHMACdFlows (Maximum number of HS-DSCH MACd flows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3189
MaxNumberUECmHO (Maximum number of UEs in CM due to critical HO
measurement ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3191
MaxNumberUECmSLHO (Maximum number of UEs in CM due to SLHO
measurement ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3192
MaxNumberUEHSPACmHO (Max number of UEs in HSDPA CM due to
critical HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3194
MaxNumberUEHSPACmNCHO (Max number of UEs in HSDPA CM due
to NCHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3195
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
44.245
44.246
44.247
44.248
44.249
44.250
44.251
44.252
44.253
44.254
44.255
44.256
44.257
44.258
44.259
44.260
44.261
44.262
44.263
44.264
44.265
44.266
44.267
44.268
44.269
44.270
44.271
44.272
44.273
44.274
44.275
44.276
44.277
44.278
44.279
44.280
DN00211177
Issue 12B
MaxTotalUplinkSymbolRate (Maximum total uplink symbol rate) . . . 3197
MinAllowedBitRateDL (Minimum allowed bit rate in downlink) . . . . . 3199
MinAllowedBitRateUL (Minimum allowed bit rate in uplink). . . . . . . . 3201
MultiplePLMNListIncluded (Multiple PLMN List Included) . . . . . . . . . 3203
N300 (N300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3204
N312 (N312) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3205
N312Conn (N312 for connected mode) . . . . . . . . . . . . . . . . . . . . . . . 3206
N313 (N313) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3208
N315 (N315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3209
NASsignVolThrDL (Downlink NAS signalling volume threshold) . . . . 3211
NASsignVolThrUL (Uplink NAS signalling volume threshold) . . . . . . 3213
NCr (Maximum number of cell reselections) . . . . . . . . . . . . . . . . . . . 3214
NbrOfSCCPCHs (Number of SCCPCHs) . . . . . . . . . . . . . . . . . . . . . 3216
NforCTCH (Period of CTCH allocation (N)) . . . . . . . . . . . . . . . . . . . . 3217
NonHCSNcr (Maximum number of cell reselections in non-HCS case) . .
3219
NonHCSTcrMax (Evaluating period for amount of reselections in nonHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3220
NonHCSTcrMaxHyst (Hysteresis to revert from UE measurement in nonHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3222
NonHSEventECommMeas (Event E measurement of non HS transmitted
carrier power). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3223
NrtFmcgIdentifier (NRT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . 3225
NrtFmciIdentifier (NRT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 3226
NrtFmcsIdentifier (NRT FMCS Identifier). . . . . . . . . . . . . . . . . . . . . . 3227
NumberEDCHReservedSHOBranchAdditions (Number of E-DCHs reserved for SHO branch additions) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3228
OCULNRTDCHGrantedMinAllocT (DCH time limit for UL NRT DCH overload in E-DCH cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3229
OCdlNrtDCHgrantedMinAllocT (Threshold for DL NRT DCH allocation time
in enhanced overload control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3231
OffsetToBeginCTCHBSIndex (Offset to Begin CTCH Block Set Index) . .
3232
PBSgrantedMinDCHallocT (PBS granted min DCH allocation time) . 3233
PBSgrantedMinDCHallocTequalP (PBS granted min DCH allocation time
equal priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3234
PBSgrantedMinDCHallocThigherP (PBS granted min DCH allocation time
higher priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3235
PBSgrantedMinDCHallocTlowerP (PBS granted min DCH allocation time
lower priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3237
PCH24kbpsEnabled (Activate \ Deactivate support for 24kbps PCH) 3238
PFLIdentifier (PFL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3239
PICState (PIC state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3240
PI_amount (Number of PI per frame). . . . . . . . . . . . . . . . . . . . . . . . . 3241
PRACHDelayRange (PRACH Propagation Delay Statistics Cell Range) .
3242
PRACHRequiredReceivedCI (Required received C/I on PRACH at WCDMA BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3243
PRACHScramblingCode (PRACH scrambling code). . . . . . . . . . . . . 3244
Id:0900d805809d7397
87
WCDMA Radio Network Configuration Parameters
44.281
44.282
44.283
44.284
44.285
44.286
44.287
44.288
44.289
44.290
44.291
44.292
44.293
44.294
44.295
44.296
44.297
44.298
44.299
44.300
44.301
44.302
44.303
44.304
44.305
44.306
44.307
44.308
44.309
44.310
44.311
44.312
44.313
44.314
44.315
44.316
88
PRACH_preamble_retrans (PRACH Preamble Retrans Max) . . . . . . 3245
PSGroupId (Restriction Group Id for Packet Switched Acces) . . . . . . 3246
PTxPICH (Transmission power of the PICH channel) . . . . . . . . . . . . 3247
PWSMAVLimitDCHSDPA (Limit for DC HSDPA users in activation) . 3249
PWSMAVLimitNRTHSDPA (Limit for NRT HSDPAs for Cell Activation Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3250
PWSMAVLimitRTDCH (RT DCH power limit for activation) . . . . . . . . 3251
PWSMAVLimitRTHSDPA (Limit for RT HSDPAs for Cell Activation Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3251
PWSMAVPwrNRTHSDPA (NRT HSDPA power per user limit) . . . . . 3252
PWSMAVPwrRTHSDPA (RT HSDPA power limit for activation) . . . . 3253
PWSMCellGroup (The PWSM cell group of a cell.) . . . . . . . . . . . . . . 3254
PWSMEXPwrLimit (Power limit for virtual AC) . . . . . . . . . . . . . . . . . . 3255
PWSMEXUsrLimit (User limit for virtual AC). . . . . . . . . . . . . . . . . . . . 3256
PWSMSDLimitDCHSDPA (Limit for DC HSDPA users in shutdown) . 3257
PWSMSDLimitNRTDCH (NRT DCH limit for shutdown) . . . . . . . . . . 3258
PWSMSDLimitNRTHSDPA (Limit for NRT HSDPAs for Cell Shutdown Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3259
PWSMSDLimitRTDCH (RT DCH limit for shutdown) . . . . . . . . . . . . . 3260
PWSMSDLimitRTHSDPA (Limit for RT HSDPAs for Cell Shutdown Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3261
PWSMSDPwrNRTHSDPA (NRT HSDPA power per user margin). . . 3262
PWSMSDPwrRTDCH (RT DCH Power limit for shutdown) . . . . . . . . 3262
PWSMSDPwrRTHSDPA (RT HSDPA power limit for shutdown) . . . . 3263
PWSMShutdownOrder (The shutdown order of cells in one PWSM cell
group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3264
PWSMShutdownRemCell (Shutdown of a remaining cell) . . . . . . . . . 3265
PowerOffsetLastPreamblePRACHmessage (Power offset last preamble
and PRACH message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3266
PowerOffsetPreamHSRACH (Power Offset Last Transmitted Preamble for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3268
PowerOffsetSCCPCHTFCI (Power offset for S-CCPCH TFCI) . . . . . 3269
PO1_15 (Power offset for SCCPCH TFCI (15 ksps)) . . . . . . . . . . . . . 3270
PO1_30 (Power offset for SCCPCH TFCI (30 ksps)) . . . . . . . . . . . . . 3271
PO1_60 (Power offset for SCCPCH TFCI (60 ksps)) . . . . . . . . . . . . . 3272
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3274
PowerRampStepPRACHpreamble (Power ramp step on PRACH preamble) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3275
PowerSaveHSPAType (HSPA Type of Cell in Power Saving Mode) . 3276
PriScrCode (Primary downlink scrambling code) . . . . . . . . . . . . . . . . 3278
PrxLoadMarginDCH (Interference margin for the minimum UL DCH load)
3279
PrxLoadMarginEDCH (Interference margin for the minimum E-DCH load)
3281
PrxLoadMarginMaxDCH (Interference margin for the maximum UL DCH
load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3282
PrxMaxOrigTargetBTS (Max target received wide band original power for
BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3284
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
44.317
44.318
44.319
44.320
44.321
44.322
44.323
44.324
44.325
44.326
44.327
44.328
44.329
44.330
44.331
44.332
44.333
44.334
44.335
44.336
44.337
44.338
44.339
44.340
44.341
44.342
44.343
44.344
44.345
44.346
44.347
44.348
44.349
44.350
44.351
44.352
44.353
44.354
DN00211177
Issue 12B
PrxMaxTargetBTS (Maximum target received wide band power for BTS)
3285
PrxMeasFilterCoeff (Filtering Coefficient of PrxTotal measurement). 3286
PrxNoise (Uplink noise level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3288
PrxNoiseAutotuning (PrxNoise autotuning allowed) . . . . . . . . . . . . . 3289
PrxOffset (Offset for received power) . . . . . . . . . . . . . . . . . . . . . . . . 3290
PrxOffsetWPS (Offset for received Wireless Priority Service power) 3291
PrxTarget (Target for received power). . . . . . . . . . . . . . . . . . . . . . . . 3292
PrxTargetMax (Maximum target for the received total wideband power) .
3293
PrxTargetPSMax (Max PS target in HSPA-DCH interference sharing) . . .
3295
PrxTargetPSMaxtHSRACH (Max PS target interference level with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3296
PrxTargetPSMin (Min PS target in HSPA-DCH interference sharing) 3297
PrxTargetPSStepDown (PS target step down in HSPA-DCH interference
sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3299
PrxTargetPSStepUp (PS target step up in HSPA-DCH interference sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3300
PrxTotalReportPeriod (Reporting period for the RTWP measurements). .
3301
PtxAICH (Transmission power of the AICH channel) . . . . . . . . . . . . 3302
PtxBCCHHSPDSCH (HS-PDSCH Power of HS-FACH for BCCH) . . 3303
PtxBCCHHSSCCH (HS-SCCH Power of HS-FACH for BCCH) . . . . 3304
PtxCellMax (Cell maximum transmission power). . . . . . . . . . . . . . . . 3305
PtxDLabsMax (Planned maximum downlink transmission power of a radio
link) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3307
PtxFDPCHMax (F-DPCH maximum transmission power) . . . . . . . . . 3308
PtxFDPCHMin (F-DPCH minimum transmission power) . . . . . . . . . . 3309
PtxHighHSDPAPwr (High threshold of PtxTotal for dynamic HSDPA pwr alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3311
PtxMarginCCH (Margin for total downlink transmission power for downlink
channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3312
PtxMaxEHICH (The Maximum transmission power E-HICH) . . . . . . 3313
PtxMaxHSDPA (Maximum allowed HSDPA power) . . . . . . . . . . . . . 3314
PtxMeasFilterCoeff (Filtering Coefficient of PtxTotal measurement) . 3315
PtxOffset (Offset for transmitted power) . . . . . . . . . . . . . . . . . . . . . . 3316
PtxOffsetEAGCH (The transmission power offset of the E-AGCH) . . 3318
PtxOffsetEAGCHDPCCH (The power offset of the E-AGCH) . . . . . . 3319
PtxOffsetEHICHDPCCH (The power offset of the E-HICH). . . . . . . . 3320
PtxOffsetERGCH (The transmission power offset of the E-RGCH). . 3322
PtxOffsetERGCHDPCCH (The power offset of the E-RGCH) . . . . . . 3323
PtxOffsetExxCH2ms (The power offset of E-xxCH for 2ms TTI) . . . . 3325
PtxOffsetExxCHSHO (The power offset of E-xxCH for SHO) . . . . . . 3326
PtxOffsetFDPCHSHO (The power offset of F-DPCH for SHO) . . . . . 3327
PtxOffsetHSDPA (Offset for transmitted non-HSDPA power) . . . . . . 3328
PtxOffsetHSSCCH (The power offset of the HS-SCCH) . . . . . . . . . . 3329
PtxOffsetWPS (Offset for transmitted Wireless Priority Service power) . .
3330
Id:0900d805809d7397
89
WCDMA Radio Network Configuration Parameters
44.355
44.356
44.357
44.358
44.359
44.360
44.361
44.362
44.363
44.364
44.365
44.366
44.367
44.368
44.369
44.370
44.371
44.372
44.373
44.374
44.375
44.376
44.377
44.378
44.379
44.380
44.381
44.382
44.383
44.384
44.385
44.386
44.387
44.388
90
PtxPSstreamAbsMax (Maximum transmitted code power of PS streaming
RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3331
PtxPrimaryCCPCH (Transmission power of the primary CCPCH channel)
3333
PtxPrimaryCPICH (Transmission power of the primary CPICH channel) . .
3334
PtxPrimarySCH (Transmission power of the primary SCH channel) . 3336
PtxSCCPCH1 (Tx power of S-CCPCH for PCH/FACH(s) or standalone
FACH(s)). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3337
PtxSCCPCH2 (Tx power of S-CCPCH for Standalone PCH) . . . . . . . 3339
PtxSCCPCH2SF128 (Tx power of S-CCPCH for Standalone PCH SF 128)
3340
PtxSCCPCH3 (Tx power of S-CCPCH for SAB). . . . . . . . . . . . . . . . . 3342
PtxSecSCH (Transmission power of the secondary SCH channel) . . 3343
PtxTarget (Target for transmitted power) . . . . . . . . . . . . . . . . . . . . . . 3344
PtxTargetHSDPA (Target for transmitted non-HSDPA power). . . . . . 3345
PtxTargetPSAdjustPeriod (DCH PS target adjust period for dyn HSDPA
pwr alloc). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3347
PtxTargetPSMax (Max DCH PS target for dynamic HSDPA pwr allocation)
3348
PtxTargetPSMaxtHSRACH (Max PS target power level with HS-RACH) .
3350
PtxTargetPSMin (Min DCH PS target for dynamic HSDPA pwr allocation)
3351
PtxTargetPSStepDown (DCH PS target step down for dynamic HSDPA
pwr alloc). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3352
PtxTargetPSStepUp (DCH PS target step up for dynamic HSDPA pwr alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3353
PtxTargetTotMax (Maximum value for dynamic total tx power) . . . . . 3355
PtxTargetTotMin (Minimum value for dynamic total tx power) . . . . . . 3356
PtxThresholdCCH (Threshold for total downlink transmission power for
downlink channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3358
PtxTotalReportPeriod (Reporting period for the TCP measurements.) . . .
3359
QHCS (Quality threshold level for HCS) . . . . . . . . . . . . . . . . . . . . . . . 3360
Qhyst1 (Cell reselection hysteresis 1) . . . . . . . . . . . . . . . . . . . . . . . . 3361
Qhyst1FACH (Cell reselection hysteresis 1 for FACH). . . . . . . . . . . . 3362
Qhyst1PCH (Cell reselection hysteresis 1 for PCH) . . . . . . . . . . . . . . 3363
Qhyst2 (Cell reselection hysteresis 2) . . . . . . . . . . . . . . . . . . . . . . . . 3364
Qhyst2FACH (Cell reselection hysteresis 2 for FACH). . . . . . . . . . . . 3365
Qhyst2PCH (Cell reselection hysteresis 2 for PCH) . . . . . . . . . . . . . . 3366
QqualMin (Minimum required quality level in the cell) . . . . . . . . . . . . 3367
QrxlevMin (Minimum required RX level in the cell) . . . . . . . . . . . . . . . 3368
RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3369
RACHCapacity (RACH Capacity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3371
RACHInterFreqMesQuant (RACH Inter Frequency Measurement Quantity)
3372
RACHIntraFreqMesQuant (RACH Intra Frequency Measurement Quantity)
3373
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
44.389
44.390
44.391
44.392
44.393
44.394
44.395
44.396
44.397
44.398
44.399
44.400
44.401
44.402
44.403
44.404
44.405
44.406
44.407
44.408
44.409
44.410
44.411
44.412
44.413
44.414
44.415
44.416
44.417
44.418
44.419
44.420
DN00211177
Issue 12B
RACH_Tx_NB01max (RACH random back-off upper bound) . . . . . . 3375
RACH_Tx_NB01min (RACH random back-off lower bound). . . . . . . 3376
RACH_tx_Max (RACH maximum number of preamble cycles). . . . . 3378
RACHloadReportPeriod (Reporting period of Acknowledged PRACH Preambles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3379
RACHmeasFilterCoeff (Filtering Coefficient of PRACH measurement). . .
3380
RNARGroupId (Radio Network Access Regulation Function Group Id) . .
3383
RRCconnRepTimer1 (RRC connection setup Retransmission Timer1) . .
3384
RRCconnRepTimer2 (RRC connection setup Retransmission Timer2) . .
3385
RSEPSEventECommMeas (Event E measurement of RSEPS) . . . . 3386
RTWPEventECommHyst (Hysteresis time of RTWP Event E measurements) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3387
RTWPEventECommMeas (Event E measurement of received total wide
band power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3388
RTWPMeasFilterCoeff (Filtering Coefficient of RTWP common measurements) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3390
RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for speech services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3392
RTWithHSDPAFmciIdentifier (HSDPA FMCI identifier for speech services)
3393
RTWithHSDPAFmcsIdentifier (HSDPA FMCS identifier for speech services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3395
RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for speech services)
3396
RXBurstHSFACH (HS-FACH Reception Burst). . . . . . . . . . . . . . . . . 3398
RachLoadMarginCCH (Margin for RACH load for downlink channel type
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3399
RachLoadThresholdCCH (Threshold for RACH load for downlink channel
type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3400
RefServForCodePower (Reference service in the max code power definition) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3401
RelocComm_in_InterRNC_HHO (Usage of Relocation Commit procedure
in inter RNC HHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3402
RsrvdSignaturesOffset (Reserved E-RGCH and E-HICH signatures per
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3403
RtFmcgIdentifier (RT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 3405
RtFmciIdentifier (RT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 3406
RtFmcsIdentifier (RT FMCS Identifier). . . . . . . . . . . . . . . . . . . . . . . . 3407
RxDivIndicator (Rx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . 3408
SABEnabled (Service Area Broadcast Enabled) . . . . . . . . . . . . . . . . 3409
SAC (Service Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3410
SACB (Service Area Code for SAB) . . . . . . . . . . . . . . . . . . . . . . . . . 3411
SHCS_RAT (Threshold for inter-RAT measurement rules in HCS). . 3413
SHCS_RATConn (Threshold for inter-RAT measurement for connected
mode ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3414
SIB4Indicator (Indicator of SIB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3415
Id:0900d805809d7397
91
WCDMA Radio Network Configuration Parameters
44.421
44.422
44.423
44.424
44.425
44.426
44.427
44.428
44.429
44.430
44.431
44.432
44.433
44.434
44.435
44.436
44.437
44.438
44.439
44.440
44.441
44.442
44.443
44.444
44.445
44.446
44.447
44.448
44.449
44.450
44.451
44.452
44.453
44.454
44.455
44.456
44.457
44.458
44.459
44.460
44.461
92
SIB7factor (SIB7 expiration time factor) . . . . . . . . . . . . . . . . . . . . . . . 3416
SIRDPCCHOffsetEDPCH (SIR target offset for DPCCH with E-DPCH) . .
3417
SRBBitRateRRCSetupEC (SRB DCH bit rate in RRC setup based on EC)
3418
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . . 3419
SRBHSPAFmcsId (FMCS identifier for standalone SRB on HSPA) . . 3420
SRBMapRRCSetupEC (SRB mapping in RRC setup based on EC) . 3422
SectorID (Sector Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3423
ServHONumbUEInterFreq (Number of inter-frequency service HOs) 3425
ServHONumbUEInterRAT (Number of inter-RAT service HOs) . . . . . 3426
ServHOPeriodInterFreq (Period to start inter-frequency service HOs)3428
ServHOPeriodInterRAT (Period to start inter-RAT service HOs) . . . . 3429
ShutdownStepAmount (Shutdown step amount) . . . . . . . . . . . . . . . . 3430
ShutdownWindow (Shutdown window). . . . . . . . . . . . . . . . . . . . . . . . 3431
Sintersearch (S intersearch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3432
SintersearchConn (S intersearch for connected mode) . . . . . . . . . . . 3433
Sintrasearch (S intrasearch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3435
SintrasearchConn (S intrasearch for connected mode) . . . . . . . . . . . 3436
Slimit_SearchRAT (S limit,SearchRAT) . . . . . . . . . . . . . . . . . . . . . . . 3437
Slimit_SearchRATConn (S limit,SearchRAT for connected mode) . . 3438
SmartLTELayeringEnabled (Smart LTE Layering Enabled) . . . . . . . . 3439
SmartLTELayeringRSCP (Smart LTE Layering RSCP threshold) . . . 3441
SmartLTELayeringTSysSel (Smart LTE Layering Target System Selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3443
SmartLTELayeringUA (Smart LTE Layering NRT user amount threshold)
3444
SmartTrafVolThrDL (DL traffic volume threshold for Smartphone) . . . 3445
SmartTrafVolThrUL (UL traffic volume threshold for Smartphone) . . . 3447
SpeedScaleTresel (Scaling factor of Treselection for UE in high mobility) .
3448
Sprioritysearch1 (S prioritysearch1) . . . . . . . . . . . . . . . . . . . . . . . . . . 3449
Sprioritysearch2 (S prioritysearch2) . . . . . . . . . . . . . . . . . . . . . . . . . . 3451
SsearchHCS (S searchHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452
SsearchHCSConn (S searchHCS for connected mode). . . . . . . . . . . 3453
Ssearch_RAT (S searchRAT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3454
Ssearch_RATConn (S searchRAT for connected mode) . . . . . . . . . . 3455
T300 (T300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3457
T312 (T312) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3458
T312Conn (T312 for connected mode). . . . . . . . . . . . . . . . . . . . . . . . 3459
T313 (T313) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3460
T315 (T315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3461
T321 (High Speed Cell FACH DRX operation timer) . . . . . . . . . . . . . 3462
TBarred (Cell barred period) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3463
TCPEventECommHyst (Hysteresis time of TCP Event E measurements) .
3465
TCPEventECommMeas (Event E measurement of transmitted carrier power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3466
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
44.462
44.463
44.464
44.465
44.466
44.467
44.468
44.469
44.470
44.471
44.472
44.473
44.474
44.475
44.476
44.477
44.478
44.479
44.480
44.481
44.482
44.483
44.484
44.485
44.486
44.487
44.488
44.489
44.490
44.491
44.492
44.493
44.494
44.495
44.496
DN00211177
Issue 12B
TCPMeasFilterCoeff (Filtering Coefficient of TCP common measurements)
3467
TCrmax (Evaluating period for amount of cell reselections) . . . . . . . 3469
TCrmaxHyst (Hysteresis to revert from UE high-mobility measurements)
3470
TPCCommandERTarget (TPC command error rate target) . . . . . . . 3471
TargetNSEDCHToTotalEDCHPR (Target non-serving E-DCH to total EDCH power ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3473
Tcell (Frame timing offset of a cell) . . . . . . . . . . . . . . . . . . . . . . . . . . 3474
Threshservlow (Thresh serving low) . . . . . . . . . . . . . . . . . . . . . . . . . 3477
ToAWE_CCH (Time of Arrival Window Endpoint for common channels) .
3478
ToAWS_CCH (Time of Arrival Window Startpoint for common channels).
3479
TrafVolThresholdDLLow (Downlink traffic volume measurement low
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3481
Treselection (Cell reselection triggering time) . . . . . . . . . . . . . . . . . . 3482
TreselectionFACH (Cell reselection triggering time for FACH) . . . . . 3483
TreselectionPCH (Cell reselection triggering time for PCH) . . . . . . . 3485
UARFCN (UTRA Absolute Radio Frequency Channel Number) . . . . 3486
UEDRXCapability (UE DRX in Cell_FACH capability). . . . . . . . . . . . 3489
UEtxPowerMaxDPCH (Maximum UE transmission power on DPCH) 3490
UEtxPowerMaxPRACH (Maximum UE transmission power on PRACH) .
3491
UEtxPowerMaxPRACHConn (Max UE transmission power on PRACH for
connected mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3492
ULLoadStateHSUBRLimit (UL loaded state for HSPAusers bit rate limit) .
3494
ULLoadStateHSUOffset (UL loaded state for HSPA users offset). . . 3495
URAId (URA identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3496
UTRAN_DRX_length (UTRAN DRX cycle length). . . . . . . . . . . . . . . 3497
UePeriodicMeasEnabled (UE Periodic Measurement Report Enabled) . .
3498
UseOfHCS (Use of HCS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3499
UsersPerHSSCCHCode (Max nbr of conv users per reserved HS-SCCH
code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3500
VCPMaxHSDPAUsers (Temporary max number of HSDPA users for the
VCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3501
VCPPtxOffset (Voice Call Priority target threshold for HSDPA prevention)
3502
VoiceCallPriority (Voice Call Prioritisation During High Traffic Load) 3504
VoiceOverrideSTHSUPA (Override switch for voice services in the HSUPA
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3505
WACSetIdentifier (WAC Parameter Set Identifier). . . . . . . . . . . . . . . 3506
WCELChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . 3507
WCELGlobalCNid (Global CN Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3508
WCELMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . 3510
WCELMNC (Mobile Network Code). . . . . . . . . . . . . . . . . . . . . . . . . . 3510
WCELMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . 3511
Id:0900d805809d7397
93
WCDMA Radio Network Configuration Parameters
44.497
WCelState (WCDMA Cell Operational State) . . . . . . . . . . . . . . . . . . . 3512
45
45.1
45.2
45.3
45.4
WLCSE Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3515
AntBearing (Antenna Bearing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3515
AntHPBW (Antenna HPBW (Half Power Beam Width) for Cell) . . . . . 3516
AntennaCoord (Antenna Coordinates) . . . . . . . . . . . . . . . . . . . . . . . . 3516
AntennaCoordAltitudeDirect (Antenna Coordinates Altitude Direction) . . .
3518
AntennaCoordAltitudeGround (Antenna Coordinates Altitude of Ground
Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3519
AntennaCoordLatitudeDegrees (Antenna Coordinates Latitude Degrees) .
3520
AntennaCoordLatitudeFractions (Antenna Coordinates Latitude Fractions)
3521
AntennaCoordLatitudeMinutes (Antenna Coordinates Latitude Minutes). .
3522
AntennaCoordLatitudeSeconds (Antenna Coordinates Latitude Seconds)
3523
AntennaCoordLatitudeSign (Antenna Coordinates Latitude Sign) . . . 3524
AntennaCoordLongitudeDegrees (Antenna Coordinates Longitude Degrees) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3525
AntennaCoordLongitudeFractions (Antenna Coordinates Longitude Fractions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3526
AntennaCoordLongitudeMinutes (Antenna Coordinates Longitude Minutes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3527
AntennaCoordLongitudeSeconds (Antenna Coordinates Longitude Seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3528
AntennaCoordLongitudeSign (Antenna Coordinates Longitude Sign) 3529
CovType (Coverage Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3530
EnvCharact (Environment characterisation) . . . . . . . . . . . . . . . . . . . . 3531
MaxCellBackRad (Maximum Cell back radius). . . . . . . . . . . . . . . . . . 3532
MaxCellRad (Maximum cell radius) . . . . . . . . . . . . . . . . . . . . . . . . . . 3533
RepeaterExist (Repeater exist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3534
WLCSEChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 3535
WLCSEUtranCellId (LCSE UTRAN Cell Id) . . . . . . . . . . . . . . . . . . . . 3536
WLCSECId (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3537
WLCSEMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . 3538
WLCSEMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . 3538
WLCSEMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . 3539
WLCSERncId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3540
WLCSEid (WLCSE Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3541
45.5
45.6
45.7
45.8
45.9
45.10
45.11
45.12
45.13
45.14
45.15
45.16
45.17
45.18
45.19
45.20
45.21
45.22
45.23
45.24
45.25
45.26
45.27
45.28
46
46.1
46.2
46.3
46.4
46.5
94
WRAB Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3543
DeltaSIR (Delta SIR in the compressed mode) . . . . . . . . . . . . . . . . . 3543
DeltaSIRAfterDownlink (Downlink delta SIR after in the compressed mode)
3544
DeltaSIRAfterUplink (Uplink delta SIR after in the compressed mode) . . .
3545
DeltaSIRDownlink (Downlink delta SIR in the compressed mode) . . . 3546
DeltaSIRUplink (Uplink delta SIR in the compressed mode) . . . . . . . 3547
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
46.6
46.7
46.8
46.9
46.10
46.11
46.12
46.13
46.14
46.15
46.16
46.17
46.18
46.19
46.20
46.21
46.22
46.23
46.24
46.25
46.26
46.27
46.28
46.29
46.30
46.31
46.32
46.33
46.34
46.35
46.36
46.37
DN00211177
Issue 12B
DownlinkOrthog (Downlink orthogonality factor) . . . . . . . . . . . . . . . . 3547
EDCHBLERAdjCSVoice10 (HARQ threshold for OLPC of HS CS voice ETTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3549
EDCHBLERAdjCSVoice2 (HARQ threshold for OLPC of HS CS voice ETTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3550
EDCHBLERAdjPSConvSpe10 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 10 ms). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3551
EDCHBLERAdjPSConvSpe2 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 2 ms). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3553
EbNoDCHOfPSNRT (Rate matching with the PS NRT DCH) . . . . . . 3554
EbNoDCHOfPSNRTPriQua (Primary quality target of the PS NRT DCH).
3555
EbNoDCHOfPSNRTPrim (Primary Eb/N0 of the PS NRT DCH) . . . . 3556
EbNoDCHOfPSNRTSec (Secondary Eb/N0 of the PS NRT DCH) . . 3558
EbNoDCHOfPSNRTSecQua (Secondary quality target of the PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3560
EbNoDCHOfPSNRTSelQuaDL (Quality target selector for DL PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3561
EbNoDCHOfPSNRTSelQuaUL (Quality target selector for UL PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3563
EbNoDCHOfPSStr (Rate matching with the PS streaming DCH) . . . 3564
EbNoDCHOfPSStrPriQua (Primary quality target of the PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3566
EbNoDCHOfPSStrPrim (Primary Eb/N0 of the PS streaming DCH) . 3567
EbNoDCHOfPSStrSec (Secondary Eb/N0 of the PS streaming DCH)3569
EbNoDCHOfPSStrSecQua (Secondary quality target of the PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3571
EbNoDCHOfPSStrSelQuaDL (Quality target selector for DL PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3572
EbNoDCHOfPSStrSelQuaUL (Quality target selector for UL PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3574
EbNoDCHOfSRB (Rate matching with the SRB DCH) . . . . . . . . . . . 3575
EbNoDCHOfSRB136 (Planned Eb/N0 of the SRB13.6 DCH) . . . . . . 3576
EbNoDCHOfSRB136Qua (Quality target of the SRB13.6 DCH) . . . . 3578
EbNoDCHOfSRB34 (Planned Eb/N0 of the SRB3.4 DCH) . . . . . . . . 3579
EbNoDCHOfSRB34Qua (Quality target of the SRB3.4 DCH) . . . . . . 3580
EbNoDCHRateGain (Data rate gain in the Eb/N0 definition). . . . . . . 3581
EbNoDCHRateGainCSAMR (Data rate gain for the Eb/N0 of the CS AMR)
3583
EbNoDCHRateGainCSData (Data rate gain for the Eb/N0 of the CS data)
3585
EbNoDCHRateGainPSConvSpe (Data rate gain for the Eb/N0 of the PS
conv speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3587
EbNoDCHRateGainPSData (Data rate gain for the Eb/N0 of the PS data
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3589
EbNoDCHRateGainSFDown (Data rate gain selector for the Eb/N0 of the
DL DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3591
EbNoDCHRateGainSFUp (Data rate gain selector for the Eb/N0 of the UL
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3592
EbNoDCHRateGainSRB (Data rate gain for the Eb/N0 of the SRB) . 3594
Id:0900d805809d7397
95
WCDMA Radio Network Configuration Parameters
46.38
46.39
46.40
46.41
46.42
46.43
46.44
46.45
46.46
46.47
46.48
46.49
46.50
46.51
46.52
46.53
46.54
46.55
46.56
46.57
46.58
46.59
46.60
46.61
46.62
46.63
46.64
46.65
46.66
46.67
46.68
46.69
46.70
96
EbNoDCHRxDiv2 (Cell offset in the UL Eb/N0, 2-way Rx diversity). . 3595
EbNoDCHRxDiv4 (Cell offset in the UL Eb/N0, 4-way Rx diversity). . 3597
EbNoDCHTxDiv (Cell offset in the DL Eb/N0 definition). . . . . . . . . . . 3598
EbNoEDCHCSAMR (Eb/N0 planned for the E-DCH MAC-d flow of CS
voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3599
EbNoEDCHOfPSStr (EbNo for E-DCH Streaming) . . . . . . . . . . . . . . 3600
EDCHPSStr128Kbps (EbNo for E-DCH Streaming 128Kbps) . . . . . . 3601
EDCHPSStr16Kbps (EbNo for E-DCH Streaming 16Kbps) . . . . . . . . 3602
EDCHPSStr248Kbps (EbNo for E-DCH Streaming 248Kbps) . . . . . . 3603
EDCHPSStr32Kbps (EbNo for E-DCH Streaming 32Kbps) . . . . . . . . 3604
EDCHPSStr64Kbps (EbNo for E-DCH Streaming 64Kbps) . . . . . . . . 3605
EDCHPSStr8Kbps (EbNo for E-DCH Streaming 8Kbps) . . . . . . . . . . 3606
EDCHPSStrOver248Kbps (EbNo for E-DCH Streaming over 248Kbps) . .
3607
EbNoEDCHPSConvSpeech (Eb/N0 planned for E-DCH PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3608
EbNoOfCSData (Rate matching with the CS data services) . . . . . . . 3610
EbNoDCHOfCSDataNT (Planned Eb/N0 of the CS non transparent data)
3611
EbNoDCHOfCSDataNTQua (Quality target of the CS non transparent data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3613
EbNoDCHOfCSDataT (Planned Eb/N0 of the CS transparent data) . 3614
EbNoDCHOfCSDataTQua (Quality target of the CS transparent data) . . .
3616
EbNoOfCSNBAMR (Rate matching with the CS NB-AMR) . . . . . . . . 3617
EbNoDCHOfCSNBAMR122 (Planned Eb/N0 of the CS NB-AMR 12.2). . .
3618
EbNoDCHOfCSNBAMR59 (Planned Eb/N0 of the CS NB-AMR 5.9). 3620
EbNoDCHOfCSNBAMRQua (Quality target of the CS NB AMR) . . . . 3621
EbNoDCHOfCSNBAMRb (Planned Eb/N0 the CS NB-AMR subflow B) . .
3622
EbNoDCHOfCSNBAMRc (Planned Eb/N0 the CS NB-AMR subflow C) . .
3623
EbNoOfCSWBAMR (Rate matching with the CS WB-AMR) . . . . . . . 3625
EbNoDCHOfCSWBAMR1265 (Planned Eb/N0 of the CS WB-AMR 12.65)
3626
EbNoDCHOfCSWBAMRQua (Quality target of the CS WB-AMR) . . . 3628
EbNoDCHOfCSWBAMRb (Planned Eb/N0 the CS WB-AMR subflow B) .
3629
EbNoOfPSConvSpe (Rate matching with the PS conversational speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3630
EbNoDCHOfPSConvSpe (Planned Eb/N0 of the PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3631
EbNoDCHOfPSConvSpeQua (Quality target of the PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3633
L1BLERTEDCHPSConvSpe10 (BLER target for PS Conversational
speech E-TTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3634
L1BLERTEDCHPSConvSpe2 (BLER target for PS Conversational speech
E-TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3635
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
46.71
46.72
46.73
46.74
46.75
46.76
46.77
46.78
46.79
46.80
46.81
46.82
46.83
46.84
46.85
46.86
46.87
46.88
46.89
46.90
46.91
46.92
46.93
46.94
46.95
DN00211177
Issue 12B
L1BLERTEDCHVoice10 (BLER target for the HS CS voice E-TTI 10 ms)
3637
L1BLERTEDCHVoice2 (BLER target for the HS CS voice E-TTI 2 ms) . .
3638
SIRDPCCHInitialDCH (Initial SIR target for UL DPCCH with DPDCH) . . .
3639
SIRDPCCHInitialDCH128 (UL SIR target without HS-DPCCH - DPDCH SF
128) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3641
SIRDPCCHInitialDCH16 (UL SIR target without HS-DPCCH - DPDCH SF
16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3643
SIRDPCCHInitialDCH256 (UL SIR target without HS-DPCCH - DPDCH SF
256) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3644
SIRDPCCHInitialDCH32 (UL SIR target without HS-DPCCH - DPDCH SF
32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3645
SIRDPCCHInitialDCH4 (UL SIR target without HS-DPCCH - DPDCH SF 4)
3646
SIRDPCCHInitialDCH64 (UL SIR target without HS-DPCCH - DPDCH SF
64) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3647
SIRDPCCHInitialDCH8 (UL SIR target without HS-DPCCH and DPDCH
SF 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3648
SIRDPCCHInitialDCHHS128 (UL SIR target with HS-DPCCH - DPDCH SF
128) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3650
SIRDPCCHInitialDCHHS16 (UL SIR target with HS-DPCCH - DPDCH SF
16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3651
SIRDPCCHInitialDCHHS256 (UL SIR target with HS-DPCCH - DPDCH SF
256) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3652
SIRDPCCHInitialDCHHS32 (UL SIR target with HS-DPCCH - DPDCH SF
32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3653
SIRDPCCHInitialDCHHS4 (UL SIR target with HS-DPCCH - DPDCH SF 4)
3654
SIRDPCCHInitialDCHHS64 (UL SIR target with HS-DPCCH - DPDCH SF
64) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3655
SIRDPCCHInitialDCHHS8 (UL SIR target with HS-DPCCH - DPDCH SF 8)
3657
SIRDPCCHInitialDCHMax (Maximum SIR target for UL DPCCH with DPDCH only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3658
SIRDPCCHInitialDCHMin (Minimum SIR target for UL DPCCH with DPDCH only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3659
SIRDPCCHInitialDCHOffset (SIR target for UL outerloop power control
with DPDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3660
SIRDPCCHInitialDCHPSConvSpe (UL SIR target regardless of DL channel - PS conv speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3661
SIRDPCCHInitialDCHRxDiv2 (SIR target for UL DPCCH with DPDCH, 2way Rx diversity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3663
SIRDPCCHInitialDCHRxDiv4 (SIR target for UL DPCCH with DPDCH, 4way Rx diversity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3664
SIRDPCCHInitialEDCH (Initial SIR target for UL DPCCH with E-DCH) . .
3666
SIRDPCCHInitialEDCHPTT10MS (Initial SIR target for UL DPCCH with ETTI 10 ms - PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3667
Id:0900d805809d7397
97
WCDMA Radio Network Configuration Parameters
46.96
46.97
46.98
SIRDPCCHInitialEDCHPTT2MS (Initial SIR target for UL DPCCH with ETTI 2 ms - PTT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3668
WRABChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 3669
WRABId (WRAB Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3671
47
47.1
47.2
47.3
47.4
47.5
47.6
47.7
47.8
47.9
WSG Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3672
GSMRoaming (GSM Roaming allowed) . . . . . . . . . . . . . . . . . . . . . . . 3672
HomePLMN (Subscriber Home PLMN) . . . . . . . . . . . . . . . . . . . . . . . 3672
HomePlmnMCC (Home PLMN Mobile Country Code) . . . . . . . . . . . . 3673
HomePlmnMNC (Home PLMN Mobile Network Code). . . . . . . . . . . . 3674
HomePlmnMNCLength (Home PLMN Mobile Network Code Length) 3675
OperatorName (Name of the subscriber home PLMN). . . . . . . . . . . . 3676
SubscriberGroupId (Subscriber Group Identifier) . . . . . . . . . . . . . . . . 3677
WSGAuthorisedNetworkId (Identifier of the Authorised Network) . . . 3678
WSGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 3679
48
48.1
48.2
48.3
48.4
48.5
48.6
48.7
48.8
WSMLC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3681
CiPosCalcInSAS (Cell-ID based Position Calculation in SAS) . . . . . . 3681
ConfAreaLevel (Confidence Area Level) . . . . . . . . . . . . . . . . . . . . . . 3682
EmergencyShapeList (Shape Priority List for Emergency Calls) . . . . 3683
EmArc (Arc Priority for Emergency Calls) . . . . . . . . . . . . . . . . . . . . . . 3684
EmPoint (Point Priority for Emergency Calls) . . . . . . . . . . . . . . . . . . . 3686
EmPointAndAlt (Point And Altitude Priority for Emergency Calls) . . . 3687
EmPointAndCircle (Point And Circle Priority For Emergency Calls) . . 3689
EmPointAndEll3D (3D Point And Ellipse Priority For Emergency Calls) . .
3691
EmPointAndEllipse (Point And Ellipse Priority For Emergency Calls) 3693
EmPolygon (Polygon Priority for Emergency Calls) . . . . . . . . . . . . . . 3695
LCSCapacityUsage (LCS Capacity Usage) . . . . . . . . . . . . . . . . . . . . 3697
LCSInterfaceOption (LCS Interface option) . . . . . . . . . . . . . . . . . . . . 3698
LCSShapeConversion (LCS Shape Conversion) . . . . . . . . . . . . . . . . 3699
NetworkBasedAGPS (Network based A-GPS) . . . . . . . . . . . . . . . . . . 3700
NetworkIndicatorForSAS (Network indicator for SAS) . . . . . . . . . . . . 3701
OperationalMode (SMLC Operational Mode) . . . . . . . . . . . . . . . . . . . 3703
PartialAGPSDataDelivery (Partial A-GPS data delivery) . . . . . . . . . . 3704
PeriodicalReportingCapacityUsage (PeriodicalReportingCapacityUsage) .
3705
PreferredAGPSMethod (Preferred A-GPS method) . . . . . . . . . . . . . . 3706
RNCDelayTolRespTime (Location Reporting Delay Tolerant response
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3707
RNCLowDelayResponseTime (Location Reporting Low Delay Response
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3708
ShapeList (Shape Priority List for Non-Emergency Calls) . . . . . . . . . 3709
Arc (Arc Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3710
Point (Point Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3712
PointAndAlt (Point And Altitude Priority) . . . . . . . . . . . . . . . . . . . . . . . 3714
PointAndCircle (Point And Uncertainty Circle Priority) . . . . . . . . . . . . 3715
PointAndEll3D (3D Point And Ellipse Priority) . . . . . . . . . . . . . . . . . . 3717
PointAndEllipse (Point And Uncertainty Ellipse Priority). . . . . . . . . . . 3719
48.9
48.10
48.11
48.12
48.13
48.14
48.15
48.16
48.17
48.18
48.19
48.20
48.21
48.22
48.23
48.24
48.25
48.26
48.27
48.28
98
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
48.29
48.30
48.31
48.32
48.33
DN00211177
Issue 12B
Polygon (Polygon Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3721
SignallingPointCodeOfSAS (Signalling Point Code of SAS) . . . . . . . 3723
UEBasedAGPS (UE based A-GPS) . . . . . . . . . . . . . . . . . . . . . . . . . 3724
WSMLCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 3725
WSMLCid (WSMLC Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3726
Id:0900d805809d7397
99
WCDMA Radio Network Configuration Parameters
List of Tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 26
Table 27
Table 28
Table 29
Table 30
Table 31
Table 32
Table 33
Table 34
Table 35
Table 36
Table 37
Table 38
Table 39
Table 40
Table 41
Table 42
Table 43
100
How to read parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
ADJDChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 431
ADJDId (Identifier of additional intra-frequency adjacency) . . . . . . . . . 432
AdjdCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433
AdjdCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . 434
AdjdDERR (Disable Effect on Reporting Range) . . . . . . . . . . . . . . . . . 435
AdjdHSDPAHopsId (HSDPA HOPS identifier) . . . . . . . . . . . . . . . . . . 436
AdjdLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
AdjdMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438
AdjdMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
AdjdMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 440
AdjdNRTHopsId (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 441
AdjdRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442
AdjdRNCId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
AdjdRTHopsId (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 444
AdjdRTWithHSDPAHopsId (HSDPA HOPS identifier for speech services)
445
AdjdSRBHopsId (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 446
AdjdScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . 448
AdjdTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
ADJGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 450
ADJGId (Inter-system adjacency identifier) . . . . . . . . . . . . . . . . . . . . . 451
ADJGType (Inter-system Neighbour Cell Type) . . . . . . . . . . . . . . . . . 452
AdjgBCC (Base Station Colour Code) . . . . . . . . . . . . . . . . . . . . . . . . . 453
AdjgBCCH (BCCH ARFCN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454
AdjgBandIndicator (Band Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . 455
AdjgCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456
AdjgLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457
AdjgMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
AdjgMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
AdjgMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 460
AdjgNCC (Network Colour Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
AdjgSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . 462
AdjgTxPwrMaxRACH (Maximum UE TX Power on RACH) . . . . . . . . . 465
AdjgTxPwrMaxTCH (Maximum UE TX Power on TCH) . . . . . . . . . . . 466
NrtHopgIdentifier (NRT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 468
RtHopgIdentifier (RT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 469
ADJIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
ADJIId (Inter-frequency adjacency identifier) . . . . . . . . . . . . . . . . . . . . 472
AdjiCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
AdjiCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . . 474
AdjiComLoadMeasDRNCCellNCHO (NCHO activity of common load measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
AdjiEcNoOffsetNCHO (CPICH EcNo offset for the non-critical HO
procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 476
AdjiHandlingBlockedCellSLHO (Handling of blocked IF neighbour cell in
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 44
Table 45
Table 46
Table 47
Table 48
Table 49
Table 50
Table 51
Table 52
Table 53
Table 54
Table 55
Table 56
Table 57
Table 58
Table 59
Table 60
Table 61
Table 62
Table 63
Table 64
Table 65
Table 66
Table 67
Table 68
Table 69
Table 70
Table 71
Table 72
Table 73
Table 74
Table 75
Table 76
Table 77
Table 78
Table 79
Table 80
Table 81
Table 82
Table 83
Table 84
Table 85
Table 86
Table 87
DN00211177
Issue 12B
SLHO procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478
AdjiLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479
AdjiMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480
AdjiMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481
AdjiMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 482
AdjiNCHOHSPASupport (ADJI HSPA Cell for Non Critical Handover) . .
483
AdjiRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
AdjiRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
AdjiSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . 486
AdjiScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . 490
AdjiTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491
AdjiTxPwrDPCH (Maximum UE TX Power on DPCH) . . . . . . . . . . . . 492
AdjiTxPwrRACH (Maximum UE TX Power on RACH) . . . . . . . . . . . . 493
AdjiUARFCN (UTRA Absolute Radio Frequency Channel Number) . 494
BlindHOTargetCell (Blind HO target cell) . . . . . . . . . . . . . . . . . . . . . . 497
NrtHopiIdentifier (NRT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 498
RtHopiIdentifier (RT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 499
ADJLChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 501
ADJLId (Identifier of inter- system adjacency to LTE) . . . . . . . . . . . . 502
AdjLEARFCN (E-UTRA Absolute Radio Frequency Channel Number) . .
503
AdjLMeasBw (Measurement Bandwidth) . . . . . . . . . . . . . . . . . . . . . . 504
HopLIdentifier (HOPL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
ADJSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 507
ADJSId (Intra-frequency adjacency identifier) . . . . . . . . . . . . . . . . . . 508
AdjsCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
AdjsCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . 510
AdjsDERR (Disable Effect on Reporting Range) . . . . . . . . . . . . . . . . 511
AdjsEcNoOffset (CPICH Ec/No Offset) . . . . . . . . . . . . . . . . . . . . . . . . 512
AdjsLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
AdjsMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
AdjsMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
AdjsMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . 516
AdjsRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
AdjsRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518
AdjsSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . 519
AdjsScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . 522
AdjsTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523
AdjsTxPwrRACH (Maximum UE TX Power on RACH) . . . . . . . . . . . . 524
HSDPAHopsIdentifier (HSDPA HOPS identifier) . . . . . . . . . . . . . . . . 525
NrtHopsIdentifier (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . 526
RTWithHSDPAHopsIdentifier (HSDPA HOPS identifier for
speechservices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527
RtHopsIdentifier (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 528
SRBHopsIdentifier (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . 529
CBCIChangeOrigin (CBCI Change Origin) . . . . . . . . . . . . . . . . . . . . . 531
CBCIId (CBCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532
Id:0900d805809d7397
101
WCDMA Radio Network Configuration Parameters
Table 88
Table 89
Table 90
Table 91
Table 92
Table 93
Table 94
Table 95
Table 96
Table 97
Table 98
Table 99
Table 100
Table 101
Table 102
Table 103
Table 104
Table 105
Table 106
Table 107
Table 108
Table 109
Table 110
Table 111
Table 112
Table 113
Table 114
Table 115
Table 116
Table 117
Table 118
Table 119
Table 120
Table 121
Table 122
Table 123
Table 124
Table 125
Table 126
102
CBCIPaddrType (Type of CBC IP address) . . . . . . . . . . . . . . . . . . . . . 533
CBCIPaddress (IP address of the CBC) . . . . . . . . . . . . . . . . . . . . . . . 534
ETWSsupportEnabled (ETWS Support Enabled) . . . . . . . . . . . . . . . . 535
ICSUforCBC (ICSU for CBC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536
IUOIdentifier (IUO Object Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 537
ACBarredListSystem (Access Class Barred List given by System) . . . 538
CMOBChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 540
CMOBId (Congestion Management Group Identifier) . . . . . . . . . . . . . 541
CellAccessRestriction (Cell Access Restriction) . . . . . . . . . . . . . . . . . 542
RestrictionGroupName (Restriction group name) . . . . . . . . . . . . . . . . 543
RestrictionGroupType (Restriction group type) . . . . . . . . . . . . . . . . . . 544
TrafficRestriction (Traffic Restriction) . . . . . . . . . . . . . . . . . . . . . . . . . . 545
AAL2LossRatio (AAL2 CPS-SDU loss ratio) . . . . . . . . . . . . . . . . . . . . 547
AAL2Multiplexing (BTS AAL2 multiplexing) . . . . . . . . . . . . . . . . . . . . . 548
AAL2MuxDelay (AAL2 CPS-SDU multiplexing delay) . . . . . . . . . . . . . 549
AAL2QueueHSDPAWithFC (AAL2 Queue Length for HSDPA With Flow
Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
AAL2QueueHSDPAWithoutFC (AAL2 Queue Length for HSDPA Without
Flow Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
AAL2QueueHSUPA (AAL2 Queue Length for HSUPA) . . . . . . . . . . . 552
AAL2QueueNRTDCHWithFC (AAL2 Queue Length for NRT DCH With
Flow Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553
AAL2QueueNRTDCHWithoutFC (AAL2 Queue Length for NRT DCH Without Flow Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554
AAL2QueueRTDCH (AAL2 Queue Length for RT DCH) . . . . . . . . . . . 555
AAL2SignLinkTP (AAL2 signalling link configuration) . . . . . . . . . . . . . 556
AAL2SigCDVT01Egr (AAL2 signalling link VCLtp CDVT egress) . . . . 557
AAL2SigCDVT01Ing (AAL2 signalling link VCLtp CDVT ingress) . . . . 558
AAL2SigEarlyPacketDiscard (AAL2 SL Early Packet Discard) . . . . . . 559
AAL2SigEgressMDCR (AAL2 SL Egress Minimum Desired Cell Rate) . .
560
AAL2SigEgressUBRShare (AAL2 SL Egress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
AAL2SigIngressMDCR (AAL2 SL Ingress Minimum Desired Cell Rate) . .
562
AAL2SigIngressUBRShare (AAL2 SL Ingress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563
AAL2SigPCR01Egr (AAL2 signalling link VCLtp PCR egress) . . . . . . 564
AAL2SigPCR01Ing (AAL2 signalling link VCLtp PCR ingress) . . . . . . 565
AAL2SigPartialPacketDiscard (AAL2 SL Partial Packet Discard) . . . . 566
AAL2SigServiceCategory (AAL2 SL Service Category) . . . . . . . . . . . 567
AAL2SigTPAdmState (AAL2 signalling link VCLtp effective administrative
state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568
AAL2SignLinkATMIfId (AAL2 signalling link ATM interface Identifier) . 569
AAL2SignLinkTPId (AAL2 signalling link termination point Identifier ) . 570
AAL2SignLinkVCI (AAL2 signalling link Virtual Channel Identifier) . . . 571
AAL2SignLinkVPI (AAL2 signalling link Virtual Path Identifier) . . . . . . 572
AAL2TP (AAL2 user plane link configuration) . . . . . . . . . . . . . . . . . . . 573
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 127
Table 128
Table 129
Table 130
Table 131
Table 132
Table 133
Table 134
Table 135
Table 136
Table 137
Table 138
Table 139
Table 140
Table 141
Table 142
Table 143
Table 144
Table 145
Table 146
Table 147
Table 148
Table 149
Table 150
Table 151
Table 152
Table 153
Table 154
Table 155
Table 156
Table 157
Table 158
Table 159
Table 160
Table 161
Table 162
Table 163
Table 164
Table 165
Table 166
Table 167
DN00211177
Issue 12B
AAL2FallbAttribute (AAL2 Fallback attribute) . . . . . . . . . . . . . . . . . . . 575
AAL2PathId (AAL type 2 path identifier) . . . . . . . . . . . . . . . . . . . . . . . 576
AAL2PathType (AAL2 Path Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . 577
AAL2SignLinkATMIfId (AAL2 signalling link ATM interface Identifier) 579
AAL2SignLinkVCI (AAL2 signalling link Virtual Channel Identifier) . . 580
AAL2SignLinkVPI (AAL2 sign link reference Virtual Path Identifier) . . 581
AAL2UPATMIfId (AAL2 user plane ATM interface Identifier) . . . . . . . 582
AAL2UPCDVT01Egr (AAL2 user plane link VCLtp CDVT egress) . . . 583
AAL2UPCDVT01Ing (AAL2 user plane link VCLtp CDVT ingress) . . . 584
AAL2UPEgressMDCR (AAL2 UP Egress Minimum Desired Cell Rate) . .
585
AAL2UPEgressUBRShare (AAL2 UP Egress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586
AAL2UPIngressMDCR (AAL2 UP Ingress Minimum Desired Cell Rate) .
587
AAL2UPIngressUBRShare (AAL2 UP Ingress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588
AAL2UPPCR01Egr (AAL2 user plane link VCLtp PCR egress) . . . . . 589
AAL2UPPCR01Ing (AAL2 user plane link VCLtp PCR ingress) . . . . . 590
AAL2UPServiceCategory (AAL2 UP Service Category) . . . . . . . . . . . 591
AAL2UPTPAdmState (AAL2 user plane link VCLtp effective administrative
state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592
AAL2UPUsage (AAL2 User Plane VCC Usage) . . . . . . . . . . . . . . . . . 593
AAL2UPVCI (AAL2 user plane Virtual Channel Identifier) . . . . . . . . . 595
AAL2UPVPI (AAL2 user plane Virtual Path Identifier) . . . . . . . . . . . . 596
ANI (Adjacent AAL type 2 node identifier) . . . . . . . . . . . . . . . . . . . . . 597
COCOA2EA (AAL type 2 end point address for Iub) . . . . . . . . . . . . . 598
DATree (Iub Digit analysis tree) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
Route (Route identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 601
VCCInBundle (VCC In Bundle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 602
WAMId (WAM identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 603
ATMEPProfileId (ATM End Point Profile Id) . . . . . . . . . . . . . . . . . . . . 604
ATMInterface (ATM interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605
ATMIfAdmState (ATM interface administrative state) . . . . . . . . . . . . . 606
ATMIfMaxBandwidthEgr (ATM interface maximum bandwidth egress) . .
607
ATMIfMaxBandwidthIng (ATM interface maximum bandwidth ingress) . .
608
ATMIfMaxVCIBits (ATM interface maximum VCI bits) . . . . . . . . . . . . 609
ATMIfMaxVPIBits (ATM interface maximum VPI bits) . . . . . . . . . . . . 609
ATMIfPhysicalTTPId (ATM interface physical TTP) . . . . . . . . . . . . . . 610
ATMInterfaceID (ATM interface identifier) . . . . . . . . . . . . . . . . . . . . . 611
ATMInterfaceType (ATM interface type) . . . . . . . . . . . . . . . . . . . . . . . 612
CNBAPTP (C-NBAP signalling link configuration) . . . . . . . . . . . . . . . 613
CNBAPCDVT01Egr (C-NBAP VCLtp CDVT egress) . . . . . . . . . . . . . 614
CNBAPCDVT01Ing (C-NBAP VCLtp CDVT ingress) . . . . . . . . . . . . . 615
CNBAPEarlyPacketDiscard (C-NBAP Early Packet Discard) . . . . . . . 616
CNBAPEgressMDCR (C-NBAP Egress Minimum Desired Cell Rate) 617
Id:0900d805809d7397
103
WCDMA Radio Network Configuration Parameters
Table 168
Table 169
Table 170
Table 171
Table 172
Table 173
Table 174
Table 175
Table 176
Table 177
Table 178
Table 179
Table 180
Table 181
Table 182
Table 183
Table 184
Table 185
Table 186
Table 187
Table 188
Table 189
Table 190
Table 191
Table 192
Table 193
Table 194
Table 195
Table 196
Table 197
Table 198
Table 199
Table 200
Table 201
Table 202
Table 203
Table 204
Table 205
Table 206
Table 207
Table 208
Table 209
104
CNBAPEgressUBRShare (C-NBAP Egress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 618
CNBAPICSUIndex (ICSU index for C-NBAP link) . . . . . . . . . . . . . . . . 619
CNBAPIngressMDCR (C-NBAP Ingress Minimum Desired Cell Rate) 620
CNBAPIngressUBRShare (C-NBAP Ingress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621
CNBAPOpState (Operational Status of C-NBAP link) . . . . . . . . . . . . . 622
CNBAPPCR01Egr (C-NBAP VCLtp PCR egress) . . . . . . . . . . . . . . . . 623
CNBAPPCR01Ing (C-NBAP VCLtp PCR ingress) . . . . . . . . . . . . . . . . 624
CNBAPPartialPacketDiscard (C-NBAP Partial Packet Discard) . . . . . 625
CNBAPServiceCategory (C-NBAP Service Category) . . . . . . . . . . . . 626
CNBAPTPATMIfId (C-NBAP ATM interface identifier) . . . . . . . . . . . . 627
CNBAPTPAdmState (C-NBAP VCLtp effective administrative state) . 628
CNBAPVCI (C-NBAP Virtual Channel Identifier) . . . . . . . . . . . . . . . . . 629
CNBAPVPI (C-NBAP Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . 630
COCOChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 631
COCOId (Connection Configuration Identifier) . . . . . . . . . . . . . . . . . . 632
CalculateCDVT (Calculate CDVT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633
CreateATMTP (Create ATM termination points) . . . . . . . . . . . . . . . . . 634
DNBAPTP (D-NBAP signalling link configuration) . . . . . . . . . . . . . . . . 635
CControlPortID (Communication Control Port) . . . . . . . . . . . . . . . . . . 636
DNBAPATMIfId (D-NBAP ATM interface identifier) . . . . . . . . . . . . . . . 637
DNBAPCDVT01Egr (D-NBAP VCLtp CDVT egress) . . . . . . . . . . . . . . 638
DNBAPCDVT01Ing (D-NBAP VCLtp CDVT ingress) . . . . . . . . . . . . . 639
DNBAPEarlyPacketDiscard (D-NBAP Early Packet Discard) . . . . . . . 640
DNBAPEgressMDCR (D-NBAP Egress Minimum Desired Cell Rate) . 641
DNBAPEgressUBRShare (D-NBAP Egress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642
DNBAPICSUIndex (ICSU index for D-NBAP link) . . . . . . . . . . . . . . . . 643
DNBAPIngressMDCR (D-NBAP Ingress Minimum Desired Cell Rate) 644
DNBAPIngressUBRShare (D-NBAP Ingress UBR Share Weight Of Excessive Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645
DNBAPOpState (Operational Status of D-NBAP link) . . . . . . . . . . . . . 646
DNBAPPCR01Egr (D-NBAP VCLtp PCR egress) . . . . . . . . . . . . . . . . 647
DNBAPPCR01Ing (D-NBAP VCLtp PCR ingress) . . . . . . . . . . . . . . . . 648
DNBAPPartialPacketDiscard (DNBAP Partial Packet Discard) . . . . . . 649
DNBAPServiceCategory (D-NBAP Service Category) . . . . . . . . . . . . 650
DNBAPTPAdmState (D-NBAP VCLtp effective administrative state) . 651
DNBAPVCI (D-NBAP Virtual Channel Identifier) . . . . . . . . . . . . . . . . . 652
DNBAPVPI (D-NBAP Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . 653
DynNRTDCHSchedPathSwitch (Dynamic NRT DCH Scheduling With Path
Selection Switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654
GenerateAAL2Num (Generate AAL2 user plane link numbers) . . . . . 655
InternalHSDPAFCMethodBTS (Internal HSDPA Flow Control Method for
BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657
VCCBundleParams (VCC Bundle parameters) . . . . . . . . . . . . . . . . . . 658
VCCBundleEBS (VCC Bundle Excess Bandwidth Share) . . . . . . . . . . 659
VCCBundleId (VCC Bundle identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 660
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 210
Table 211
Table 212
Table 213
Table 214
Table 215
Table 216
Table 217
Table 218
Table 219
Table 220
Table 221
Table 222
Table 223
Table 224
Table 225
Table 226
Table 227
Table 228
Table 229
Table 230
Table 231
Table 232
Table 233
Table 234
Table 235
Table 236
Table 237
Table 238
Table 239
Table 240
Table 241
Table 242
Table 243
Table 244
Table 245
Table 246
Table 247
Table 248
Table 249
Table 250
Table 251
Table 252
Table 253
Table 254
DN00211177
Issue 12B
VCCBundlePCR (VCC Bundle Peak Cell Rate) . . . . . . . . . . . . . . . . . 661
VPLTP (Virtual Path Link termination point) . . . . . . . . . . . . . . . . . . . . 662
COCOVPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663
VPLTPATMIfId (VPLtp ATM interface identifier) . . . . . . . . . . . . . . . . . 664
VPLTPAdmState (VPLtp effective administrative state) . . . . . . . . . . . 665
VPLTPCDVT01Egr (VPLtp CDVT egress) . . . . . . . . . . . . . . . . . . . . . 665
VPLTPEgressMDCR (VPLTP Egress Minimum Desired Cell Rate) . . 666
VPLTPPCR01Egr (VPLtp PCR egress) . . . . . . . . . . . . . . . . . . . . . . . 667
VPLTPServiceCategory (VPLtp Service Category) . . . . . . . . . . . . . . 668
VPLTPTrafficShaping (VPLtp VP level traffic shaping) . . . . . . . . . . . . 669
WBTSId (WBTS Identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 670
COSITEChangeOrigin (COSITE Change origin) . . . . . . . . . . . . . . . . 672
COSITEId (COSITE Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673
SharingState (Sharing State) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674
AdditionalStateInfo (Additional State Information) . . . . . . . . . . . . . . . 676
AdminStateInfo (Admin State Info) . . . . . . . . . . . . . . . . . . . . . . . . . . . 677
AdministrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . 678
AvailabilityStatus (Availability Status) . . . . . . . . . . . . . . . . . . . . . . . . . 679
COSRNCChangeOrigin (COSRNC Change origin) . . . . . . . . . . . . . . 681
COSRNCId (COSRNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682
ClusterIfState (Cluster Interface State) . . . . . . . . . . . . . . . . . . . . . . . . 683
OperationalState (Operational State ) . . . . . . . . . . . . . . . . . . . . . . . . . 684
PeerRNCIPAddress (Peer RNC IP Address) . . . . . . . . . . . . . . . . . . . 685
RNCOMConnState (RNC-RNC O&M Connection State) . . . . . . . . . . 686
AMRDirReCell (Usage of Directed Retry of AMR call Inter-system
Handov) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 688
DLDPCHTxPwrClOffset (DL DPCH Transmission Power Cancellation
Offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 689
FMCGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 690
FMCGId (FMCG identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691
GSMcauseCPICHEcNo (GSM HO caused by CPICH Ec/No) . . . . . . 692
GSMcauseCPICHrscp (GSM HO caused by CPICH RSCP) . . . . . . . 694
GSMcauseTxPwrDL (GSM HO caused by DL DPCH TX Power) . . . 695
GSMcauseTxPwrUL (GSM HO caused by UE TX Power) . . . . . . . . . 697
GSMcauseUplinkQuality (GSM HO caused by UL DCH Quality) . . . . 699
GsmDLTxPwrThrAMR (DL DPCH TX Power Threshold for AMR) . . . 700
GsmDLTxPwrThrCS (DL DPCH TX Power Threshold for CS) . . . . . . 701
GsmDLTxPwrThrNrtPS (DL DPCH TX Power Threshold for NRT PS) 702
GsmDLTxPwrThrRtPS (DL DPCH TX Power Threshold for RT PS) . 703
GsmMaxMeasPeriod (Maximum Measurement Period) . . . . . . . . . . . 705
GsmMeasAveWindow (Measurement Averaging Window) . . . . . . . . 706
GsmMeasRepInterval (Measurement Reporting Interval) . . . . . . . . . 707
GsmMinHoInterval (Minimum Interval Between HOs) . . . . . . . . . . . . 708
GsmMinMeasInterval (Minimum Measurement Interval) . . . . . . . . . . 708
GsmMinSLHOInterval (Minimum interval between repetitive inter-RAT
SLHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710
GsmNcellSearchPeriod (GSM Neighbour Cell Search Period) . . . . . 711
GsmUETxPwrFilterCoeff (UE TX Power Filter Coefficient) . . . . . . . . 712
Id:0900d805809d7397
105
WCDMA Radio Network Configuration Parameters
Table 255
Table 256
Table 257
Table 258
Table 259
Table 260
Table 261
Table 262
Table 263
Table 264
Table 265
Table 266
Table 267
Table 268
Table 269
Table 270
Table 271
Table 272
Table 273
Table 274
Table 275
Table 276
Table 277
Table 278
Table 279
Table 280
Table 281
Table 282
Table 283
Table 284
Table 285
Table 286
Table 287
Table 288
Table 289
Table 290
Table 291
Table 292
Table 293
Table 294
Table 295
Table 296
106
GsmUETxPwrThrAMR (UE TX Power Threshold for AMR) . . . . . . . . 713
GsmUETxPwrThrCS (UE TX Power Threshold for CS) . . . . . . . . . . . 714
GsmUETxPwrThrNrtPS (UE TX Power Threshold for NRT PS) . . . . . 716
GsmUETxPwrThrRtPS (UE TX Power Threshold for RT PS) . . . . . . . 717
GsmUETxPwrTimeHyst (UE TX Power Time Hysteresis) . . . . . . . . . . 718
IMSIbasedGsmHo (IMSI Based GSM HO) . . . . . . . . . . . . . . . . . . . . . 720
ISHOClcauseCPICHEcNo (ISHO Cancellation caused by CPICH Ec/No)
721
ISHOClcauseCPICHrscp (ISHO Cancellation caused by CPICH RSCP) .
722
ISHOClcauseTxPwrDL (ISHO Cancellation caused by DL DPCH TX
Power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
ISHOClcauseTxPwrUL (ISHO Cancellation caused by UE TX Power) 724
MaxBSICIdentTime (Maximum BSIC Identification Time) . . . . . . . . . . 725
FMCIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 727
FMCIId (FMCI identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 728
IFHOcauseCPICHEcNo (IFHO caused by CPICH Ec/No) . . . . . . . . . 729
IFHOcauseCPICHrscp (IFHO caused by CPICH RSCP) . . . . . . . . . . 730
IFHOcauseTxPwrDL (IFHO caused by DL DPCH TX Power) . . . . . . . 732
IFHOcauseTxPwrUL (IFHO caused by UE TX Power) . . . . . . . . . . . . 734
IFHOcauseUplinkQuality (IFHO caused by UL DCH Quality) . . . . . . . 736
IMSIbasedIFHO (IMSI Based IFHO) . . . . . . . . . . . . . . . . . . . . . . . . . . 737
InterFreqDLTxPwrThrAMR (DL DPCH TX Power Threshold for AMR) 738
InterFreqDLTxPwrThrCS (DL DPCH TX Power Threshold for CS) . . . 739
InterFreqDLTxPwrThrNrtPS (DL DPCH TX Power Threshold for NRT PS)
740
InterFreqDLTxPwrThrRtPS (DL DPCH TX Power Threshold for RT PS) .
741
InterFreqMaxMeasPeriod (Maximum Measurement Period) . . . . . . . . 743
InterFreqMeasAveWindow (Measurement Averaging Window) . . . . . 744
InterFreqMeasRepInterval (Measurement Reporting Interval) . . . . . . 745
InterFreqMinHoInterval (Minimum Interval Between HOs) . . . . . . . . . 746
InterFreqMinMeasInterval (Minimum Measurement Interval) . . . . . . . 747
InterFreqMinSLHOInterval (Minimum interval between repetitive IF
SLHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748
InterFreqNcellSearchPeriod (Neighbour Cell Search Period) . . . . . . . 749
InterFreqUETxPwrFilterCoeff (UE TX Power Filter Coefficient) . . . . . 750
InterFreqUETxPwrThrAMR (UE TX Power Threshold for AMR) . . . . . 751
InterFreqUETxPwrThrCS (UE TX Power Threshold for CS) . . . . . . . . 753
InterFreqUETxPwrThrNrtPS (UE TX Power Threshold for NRT PS) . . 754
InterFreqUETxPwrThrRtPS (UE TX Power Threshold for RT PS) . . . 755
InterFreqUETxPwrTimeHyst (UE TX Power Time Hysteresis) . . . . . . 756
MBLBMobilityOffset (MBLB due to Mobility EcNo Offset) . . . . . . . . . . 757
MBLBMobilityRABComb (MBLB due to Mobility RAB Combinations) . 759
ActiveSetWeightingCoefficient (Active Set Weighting Coefficient) . . . 760
AdditionReportingInterval (Addition Reporting Interval) . . . . . . . . . . . . 761
AdditionTime (Addition Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 762
AdditionWindow (Addition Window) . . . . . . . . . . . . . . . . . . . . . . . . . . . 764
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 297
Table 298
Table 299
Table 300
Table 301
Table 302
Table 303
Table 304
Table 305
Table 306
Table 307
Table 308
Table 309
Table 310
Table 311
Table 312
Table 313
Table 314
Table 315
Table 316
Table 317
Table 318
Table 319
Table 320
Table 321
Table 322
Table 323
Table 324
Table 325
Table 326
Table 327
Table 328
Table 329
Table 330
Table 331
Table 332
Table 333
Table 334
Table 335
Table 336
Table 337
Table 338
Table 339
Table 340
Table 341
DN00211177
Issue 12B
DSRepBasedSHO (Detected Set Reporting Based SHO) . . . . . . . . . 765
DropReportingInterval (Drop Reporting Interval) . . . . . . . . . . . . . . . . 767
DropTime (Drop Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 768
DropWindow (Drop Window) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 770
EDCHAddEcNoOffset (Allow E-DCH usage EcNo offset) . . . . . . . . . 771
EDCHRemEcNoOffset (CPICH EcNo offset E-DCH usage removal) . 772
EcNoFilterCoefficient (CPICH Ec/No Filter Coefficient) . . . . . . . . . . . 774
FMCSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 775
FMCSId (FMCS identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 776
HHoEcNoCancel (CPICH Ec/No HHO Cancellation) . . . . . . . . . . . . . 777
HHoEcNoCancelTime (CPICH Ec/No HHO Cancellation Time) . . . . . 779
HHoEcNoThreshold (CPICH Ec/No HHO Threshold) . . . . . . . . . . . . . 782
HHoEcNoTimeHysteresis (CPICH Ec/No HHO Time Hysteresis) . . . 783
HHoRscpCancel (CPICH RSCP HHO Cancellation) . . . . . . . . . . . . . 785
HHoRscpCancelTime (CPICH RSCP HHO Cancellation Time) . . . . . 787
HHoRscpFilterCoefficient (CPICH RSCP HHO Filter Coefficient) . . . 790
HHoRscpThreshold (CPICH RSCP HHO Threshold) . . . . . . . . . . . . . 791
HHoRscpTimeHysteresis (CPICH RSCP HHO Time Hysteresis) . . . 793
IMSIbasedSHO (IMSI Based SHO) . . . . . . . . . . . . . . . . . . . . . . . . . . 795
MaxActiveSetSize (Maximum Active Set Size) . . . . . . . . . . . . . . . . . . 796
ReplacementReportingInterval (Replacement Reporting Interval) . . . 797
ReplacementTime (Replacement Time) . . . . . . . . . . . . . . . . . . . . . . . 799
ReplacementWindow (Replacement Window) . . . . . . . . . . . . . . . . . . 801
AdjgHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . 803
AdjgHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . 804
AdjgMinRxLevNCHO (Minimum RX level for non-critical HO) . . . . . . 805
AdjgPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . 806
AdjgPenaltyTimeNCHO (Penalty time for GSM cell in non-critical HO) . .
807
AdjgPriorityCoverage (Ncell Priority for Coverage HO) . . . . . . . . . . . 808
AdjgPrioritySLHO (Neighbour cell priority for SLHO) . . . . . . . . . . . . . 809
AdjgQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . 810
AdjgQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . 811
AdjgRxLevMinHO (Minimum RX Level for Coverage HO) . . . . . . . . . 812
AdjgTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . . 813
HOPGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 814
HOPGId (HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 816
AdjiEcNoMargin (CPICH Ec/No Margin for IFHO) . . . . . . . . . . . . . . . 817
AdjiHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . 818
AdjiHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . . 819
AdjiMinEcNo (Minimum CPICH Ec/No for IFHO) . . . . . . . . . . . . . . . . 820
AdjiMinEcNoNCHO (Minimum CPICH Ec/No for non-critical IFHO) . . 820
AdjiMinRSCP (Minimum CPICH RSCP for IFHO) . . . . . . . . . . . . . . . 821
AdjiMinRscpNCHO (Minimum CPICH RSCP for non-critical IFHO) . . 822
AdjiPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . . 823
AdjiPenaltyTimeNCHO (Penalty time for WCDMA cell in non-critical HO)
824
Id:0900d805809d7397
107
WCDMA Radio Network Configuration Parameters
Table 342
Table 343
Table 344
Table 345
Table 346
Table 347
Table 348
Table 349
Table 350
Table 351
Table 352
Table 353
Table 354
Table 355
Table 356
Table 357
Table 358
Table 359
Table 360
Table 361
Table 362
Table 363
Table 364
Table 365
Table 366
Table 367
Table 368
Table 369
Table 370
Table 371
Table 372
Table 373
Table 374
Table 375
Table 376
Table 377
Table 378
Table 379
Table 380
Table 381
Table 382
Table 383
Table 384
108
AdjiPlossMargin (Pathloss Margin for IFHO) . . . . . . . . . . . . . . . . . . . . 825
AdjiPriorityCoverage (Ncell Priority for Coverage IFHO) . . . . . . . . . . . 826
AdjiPriorityDCellCAHO (Neighbour cell priority for DC HSDPA Capa Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 827
AdjiPriorityHSCAHO (Neighbour Cell Priority for HSPA Capability Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 829
AdjiPriorityMIMOCAHO (Neighbour cell priority for MIMO Capa Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 830
AdjiPriorityQuality (Ncell Priority for Quality IFHO) . . . . . . . . . . . . . . . 831
AdjiPrioritySLHO (Neighbour cell priority for service and load IFHO) . 832
AdjiQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . . 833
AdjiQoffset2 (Cell Re-selection Quality Offset 2) . . . . . . . . . . . . . . . . . 834
AdjiQqualMin (Cell Re-selection Minimum Quality) . . . . . . . . . . . . . . . 835
AdjiQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . . 836
AdjiTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . . . 837
AdjiTempOffset2 (Cell Re-selection Temporary Offset 2) . . . . . . . . . . 838
BlindHORSCPThr (Blind HO RSCP threshold) . . . . . . . . . . . . . . . . . . 840
HOPIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 841
HOPIId (HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 842
AdjLAbsPrioCellReselec (Cell Reselection Absolute Priority) . . . . . . . 843
AdjLQrxlevminEUTRA (Cell Reselection Minimum RX level) . . . . . . . 844
AdjLThreshigh (Cell Reselection Threshold high) . . . . . . . . . . . . . . . . 845
AdjLThreslow (Cell Reselection Threshold low) . . . . . . . . . . . . . . . . . 845
HOPLChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 846
HOPLId (HOPL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 848
AdjsHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . 849
AdjsHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . . 850
AdjsPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . . 851
AdjsQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . 852
AdjsQoffset2 (Cell Re-selection Quality Offset 2) . . . . . . . . . . . . . . . . 853
AdjsQqualMin (Cell Re-selection Minimum Quality) . . . . . . . . . . . . . . 854
AdjsQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . 855
AdjsTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . . . 856
AdjsTempOffset2 (Cell Re-selection Temporary Offset 2) . . . . . . . . . . 857
EcNoAveragingWindow (CPICH Ec/No Averaging Window) . . . . . . . . 858
EnableInterRNCsho (Enable Inter-RNC Soft Handover) . . . . . . . . . . . 859
EnableRRCRelease (Enable RRC Connection Release) . . . . . . . . . . 860
HHOMarginAverageEcNo (HHO Margin for Average Ec/No) . . . . . . . 862
HHOMarginPeakEcNo (HHO Margin for Peak Ec/No) . . . . . . . . . . . . 863
HOPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 864
HOPSId (HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865
HSDPAAvailabilityIur (HSDPA availability of the neighbouring DRNC cell)
866
HSUPAAvailabilityIur (HSUPA availability of the neighbouring DRNC cell)
867
ReleaseMarginAverageEcNo (Release Margin for Average Ec/No) . . 868
ReleaseMarginPeakEcNo (Release Margin for Peak Ec/No) . . . . . . . 869
CNBAP (C-NBAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 871
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 385
Table 386
Table 387
Table 388
Table 389
Table 390
Table 391
Table 392
Table 393
Table 394
Table 395
Table 396
Table 397
Table 398
Table 399
Table 400
Table 401
Table 402
Table 403
Table 404
Table 405
Table 406
Table 407
Table 408
Table 409
Table 410
Table 411
Table 412
Table 413
Table 414
Table 415
Table 416
Table 417
Table 418
Table 419
Table 420
Table 421
Table 422
Table 423
Table 424
Table 425
Table 426
Table 427
Table 428
DN00211177
Issue 12B
CNBAPConnOpState (C-NBAP connection operational state) . . . . . . 872
CNBAPICSUIndex (ICSU index for C-NBAP link) . . . . . . . . . . . . . . . 873
SCTPPortNumberCNBAP (SCTP Port Number for C-NBAP) . . . . . . 873
DNBAP (D-NBAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 874
CControlPortID (Communication Control Port identifier) . . . . . . . . . . 875
DNBAPConnOpState (D-NBAP connection operational state) . . . . . . 876
DNBAPICSUIndex (ICSU index for D-NBAP link) . . . . . . . . . . . . . . . 877
SCTPPortNumberDNBAP (SCTP Port Number for D-NBAP) . . . . . . 878
IPBasedRouteId (IP Based Route Identification) . . . . . . . . . . . . . . . . 879
IPNBChangeOrigin (IPNB Change origin) . . . . . . . . . . . . . . . . . . . . . 880
IPNBId (IPNB object identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
MinSCTPPortIub (Minimum SCTP port number) . . . . . . . . . . . . . . . . 882
NBAPDSCP (NBAP DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 883
NodeBIPAddress (Control Plane Destination Address Iub) . . . . . . . . 884
WBTSId (WBTS identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 885
BackgroundTCToDSCP (Background TC to DSCP mapping) . . . . . . 887
ConversationalTCToDSCP (Conversational TC to DSCP mapping) . 888
IPQMChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 889
IPQMId (IP Qos Management Identifier) . . . . . . . . . . . . . . . . . . . . . . . 890
InteractiveTHP1TCToDSCP (Interactive THP1 TC to DSCP mapping) . .
891
InteractiveTHP2TCToDSCP (Interactive THP2 TC to DSCP mapping) . .
892
InteractiveTHP3TCToDSCP (Interactive THP3 TC to DSCP mapping) . .
893
StreamingTCToDSCP (Streaming TC to DSCP mapping) . . . . . . . . . 894
AAL2PTSigForIuCS (AAL2PT signalling for IuCS) . . . . . . . . . . . . . . . 896
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . 897
CNId (Core Network Identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 898
CSCNNRI (NRI for CS Core routing) . . . . . . . . . . . . . . . . . . . . . . . . . 899
NRIMaxForCSCN (Maximum value of NRI range for CS Core routing) . .
900
NRIMinForCSCN (Minimum value of NRI range for CS Core routing) 901
CSFlexiIuWeight (CS Flexible Iu Weight) . . . . . . . . . . . . . . . . . . . . . . 902
DefaultCN (Default Core Network) . . . . . . . . . . . . . . . . . . . . . . . . . . . 904
IUCSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 905
IUCSId (IuCS Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 906
IUOIdentifier (IUO Object Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 907
IuState (State of Iu interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 908
MinUDPPortCS (Minimum UDP Port) . . . . . . . . . . . . . . . . . . . . . . . . . 909
NetworkInd (Network indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910
RelocationSupport (Serving RNC Relocation Support) . . . . . . . . . . . 912
RtcpActivation (RTCP activation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . . 914
TRafC (TRafC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915
TRatC (TRatC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 916
TigOR (TigOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917
TinTR (TinTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 918
Id:0900d805809d7397
109
WCDMA Radio Network Configuration Parameters
Table 429
Table 430
Table 431
Table 432
Table 433
Table 434
Table 435
Table 436
Table 437
Table 438
Table 439
Table 440
Table 441
Table 442
Table 443
Table 444
Table 445
Table 446
Table 447
Table 448
Table 449
Table 450
Table 451
Table 452
Table 453
Table 454
Table 455
Table 456
Table 457
Table 458
Table 459
Table 460
Table 461
Table 462
Table 463
Table 464
Table 465
Table 466
Table 467
Table 468
Table 469
Table 470
Table 471
Table 472
Table 473
Table 474
110
DestIPAddressCS (IP address for the IUCS destination subnet) . . . . 920
IPBasedRouteIdCS (IP Based Route Identifier for IUCS) . . . . . . . . . . 921
IPNetmaskCS (IP netmask for the IUCS destination subnet) . . . . . . . 922
IPQMIdCS (IPQM object id for IuCS) . . . . . . . . . . . . . . . . . . . . . . . . . . 924
IUCSIPChangeOrigin (IUCSIP Change Origin) . . . . . . . . . . . . . . . . . . 925
IUCSIPId (IUCSIP Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 926
CSCNDRXLength (CN CS domain specific DRX cycle length) . . . . . . 928
CS_T3212 (T3212) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 929
ICROperatorId (ICR Operator Identifier) . . . . . . . . . . . . . . . . . . . . . . . 930
ICROperatorName (ICR Operator Name) . . . . . . . . . . . . . . . . . . . . . . 931
ICRPLMNid (ICR PLMN Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 932
MCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 934
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . . 935
IUOChangeOrigin (IUO Change Origin) . . . . . . . . . . . . . . . . . . . . . . . 936
IUOId (IUO Identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 937
IuBarringDelayTimerCS (Iu Barring Delay Timer for CS) . . . . . . . . . . 938
IuBarringDelayTimerPS (Iu Barring Delay Timer for PS) . . . . . . . . . . . 939
IuBarringRecoveryGroupCS (Iu Barring Recovery Group for CS) . . . . 940
IuBarringRecoveryGroupPS (Iu Barring Recovery Group for PS) . . . . 941
IuBarringRecoveryTimerCS (Iu service barring recovery timer for CS) 942
IuBarringRecoveryTimerPS (Iu service barring recovery timer for PS) 943
IubTransportSharingInd (Iub Transport Sharing index) . . . . . . . . . . . . 945
NRILengthForCSCN (NRI length for CS Core Networks) . . . . . . . . . . 946
NRILengthForPSCN (NRI length for PS Core Networks) . . . . . . . . . . 947
NullNRIForCSPool (Null NRI value for CS Pool) . . . . . . . . . . . . . . . . . 948
NullNRIForPSPool (Null NRI value for PS Pool) . . . . . . . . . . . . . . . . . 949
OperatorWeight (Operator Weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . 950
PLMNid (PLMN identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 952
MCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . . 955
PSCNDRXLength (CN PS domain specific DRX cycle length) . . . . . . 956
PS_NMO (Network Mode of Operation) . . . . . . . . . . . . . . . . . . . . . . . 958
SharedAreaPLMNid (Shared area PLMN identity) . . . . . . . . . . . . . . . 959
SharedAreaMCC (Shared area Mobile Country Code) . . . . . . . . . . . . 961
SharedAreaMNC (Shared area Mobile Network Code) . . . . . . . . . . . . 962
SharedAreaMNClength (Shared area Mobile Network Code Length) . 963
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . . 964
CNId (Core Network Identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965
CellFACHRelocSupport (Cell_FACH state Serving RNC Relocation Support ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 966
DefaultCN (Default Core Network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967
IUOIdentifier (IUO Object Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 968
IUPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 969
IUPSId (IuPS Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 970
IuState (State of Iu interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 475
Table 476
Table 477
Table 478
Table 479
Table 480
Table 481
Table 482
Table 483
Table 484
Table 485
Table 486
Table 487
Table 488
Table 489
Table 490
Table 491
Table 492
Table 493
Table 494
Table 495
Table 496
Table 497
Table 498
Table 499
Table 500
Table 501
Table 502
Table 503
Table 504
Table 505
Table 506
Table 507
Table 508
Table 509
Table 510
Table 511
Table 512
Table 513
Table 514
Table 515
DN00211177
Issue 12B
NetworkInd (Network indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 972
PSCNNRI (NRI for PS Core routing) . . . . . . . . . . . . . . . . . . . . . . . . . 974
NRIMaxForPSCN (Maximum value of NRI range for PS Core routing) 975
NRIMinForPSCN (Minimum value of NRI range for PS Core routing) 976
PSFlexiIuWeight (PS Flexible Iu Weight) . . . . . . . . . . . . . . . . . . . . . . 977
RelocationSupport (Serving RNC Relocation Support) . . . . . . . . . . . 979
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . . 980
TDataFwd (T DATAfwd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 981
TRafC (TRafC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 982
TRatC (TRatC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983
TigOR (TigOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983
TinTR (TinTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 984
DestIPAddressPS (IP address for the IUPS destination subnet) . . . . 986
IPBasedRouteIdPS (IP Based Route Identifier for IUPS) . . . . . . . . . . 988
IPNetmaskPS (IP netmask for the IUPS destination subnet) . . . . . . . 989
IPQMIdPS (IPQM object id for IuPS) . . . . . . . . . . . . . . . . . . . . . . . . . 991
IUPSIPChangeOrigin (IUPSIP Change Origin) . . . . . . . . . . . . . . . . . . 992
IUPSIPId (IUPSIP Identifier ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 993
AAL2PTSigForIur (AAL2PT signalling for Iur) . . . . . . . . . . . . . . . . . . . 995
AppAwareRANEnabled (Application Aware RAN Enabled) . . . . . . . . 996
CellFACHnRncRelocSupport (Cell_FACH state Serving RNC Relocation
Support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 997
DSCPHighIur (DSCP high priority for Iur) . . . . . . . . . . . . . . . . . . . . . . 998
DSCPLowIur (Low priority DSCP for Iur) . . . . . . . . . . . . . . . . . . . . . . 999
DSCPMedDCHIur (DSCP medium priority on R99 DCH for Iur) . . . 1000
DelayThresholdMaxIur (Maximum Threshold for HSUPA congestion handling delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1001
DelayThresholdMidIur (Middle Threshold value for HSUPA congestion
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1002
DelayThresholdMinIur (Minimum Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1004
HSDPACCEnabledIur (HSDPA Congestion Control activation Iur) . 1005
HSDPAULCToDSCPIur (HSDPA UL FP Control traffic to DSCP mapping
Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006
HSPAOverIur (HSPA over Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
HSUPADLCToDSCPIur (HSUPA DL FP Control traffic to DSCP mapping
Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1009
IBTSSharing (IBTS Sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010
IPBasedRouteIdIur (IP based route identifier) . . . . . . . . . . . . . . . . . 1011
IURChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 1012
IURId (Iur Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1013
InterfaceMode (Configure the IUR in a special mode) . . . . . . . . . . . 1014
IurUPSupport (User Plane support of Iur connection) . . . . . . . . . . . 1015
MaxFPDLFrameSizeIur (Maximum FP downlink frame size Iur) . . . 1016
MaxIurNRTHSDSCHBitRate (Maximum NRT HS-DSCH MAC-d flow bit
rate over Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1017
MinUDPPortIur (Minimum UDP port value) . . . . . . . . . . . . . . . . . . . 1018
NRncId (Neighbour RNC identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 1019
Id:0900d805809d7397
111
WCDMA Radio Network Configuration Parameters
Table 516
Table 517
Table 518
Table 519
Table 520
Table 521
Table 522
Table 523
Table 524
Table 525
Table 526
Table 527
Table 528
Table 529
Table 530
Table 531
Table 532
Table 533
Table 534
Table 535
Table 536
Table 537
Table 538
Table 539
Table 540
Table 541
Table 542
Table 543
Table 544
Table 545
Table 546
Table 547
Table 548
Table 549
Table 550
Table 551
Table 552
112
NRncNetworkInd (Network indicator of neighbour RNC) . . . . . . . . . . 1021
NRncRelocationSupport (Serving RNC Relocation Support of neighbour
RNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1022
NRncSignPointCode (Signalling point code of neighbour RNC) . . . . 1023
NRncVersion (Release version of Neighbouring RNC) . . . . . . . . . . . 1024
NeighbouringPLMNid (Neighbouring PLMN identity) . . . . . . . . . . . . . 1026
MCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1028
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . 1029
NeighbouringRNWElement (Type of the Neighbouring RNW Element) . .
1030
OverbookingSwitchIur (Overbooking Switch Iur) . . . . . . . . . . . . . . . . 1031
ProbabilityFactorMaxIur (ProbabilityFactor for Congestion Indication
sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1032
RNSAPCongAndPreemption (RNSAP Congestion And Preemption) 1033
ToAWEOffsetNRTDCHIP (ToAWE Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1034
ToAWEOffsetRTDCHIP (ToAWE Offset for RT DCH connections over IP)
1035
ToAWSOffsetNRTDCHIP (ToAWS Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1036
ToAWSOffsetRTDCHIP (ToAWS Offset for RT DCH connections over IP)
1037
AMRToNonPreferredLayer (AMR to Non Preferred Layer) . . . . . . . . 1038
BlindHORSCPThrAbove (Blind HO RSCP threshold above) . . . . . . . 1039
BlindHORSCPThrBelow (Blind HO RSCP threshold below) . . . . . . . 1040
LaySelLowLoadPref (Layer Selection Low Load Preferred) . . . . . . . 1041
LaySelWeightBand (Layer Selection Weight of Band) . . . . . . . . . . . . 1042
LaySelWeightLoad (Layer Selection Weight of Load) . . . . . . . . . . . . 1042
LaySelWeightPrefLayer (Layer Selection Weight of Preferred Layer) 1043
LaySelWeightRSCP (Layer Selection Weight of RSCP) . . . . . . . . . . 1044
PFL64QAMAMR (Preferred Frequency Layer for 64QAM AMR) . . . 1045
PrefLayer64QAMAMR (Preferred Layer for 64QAM AMR) . . . . . . . . 1046
PFL64QAMAMRNRT (Preferred Frequency Layer for 64QAM AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1047
PrefLayer64QAMAMRNRT (Preferred Layer for 64QAM AMR and NRT) .
1048
PFL64QAMNRT (Preferred Frequency Layer for 64QAM NRT) . . . . 1049
PrefLayer64QAMNRT (Preferred Layer for 64QAM NRT) . . . . . . . . . 1050
PFL64QAMStr (Preferred Frequency Layer for 64QAM Streaming) . 1051
PrefLayer64QAMStr (Preferred Layer for 64QAM Streaming) . . . . . 1052
PFLCSHSAMR (Preferred Frequency Layer for CS voice HSPA AMR) . .
1053
PrefLayerCSHSAMR (Preferred Layer for CS voice HSPA AMR) . . . 1054
PFLCSHSAMRNRT (Preferred Frequency Layer for CS voice HSPA AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1055
PrefLayerCSHSAMRNRT (Preferred Layer for CS voice HSPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1056
PFLCSHSNRT (Preferred Frequency Layer for CS voice HSPA NRT) . . .
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 553
Table 554
Table 555
Table 556
Table 557
Table 558
Table 559
Table 560
Table 561
Table 562
Table 563
Table 564
Table 565
Table 566
Table 567
Table 568
Table 569
Table 570
Table 571
Table 572
Table 573
Table 574
Table 575
Table 576
Table 577
Table 578
Table 579
Table 580
Table 581
Table 582
Table 583
Table 584
DN00211177
Issue 12B
1057
PrefLayerCSHSNRT (Preferred Layer for CS voice HSPA NRT) . . . 1058
PFLCSHSStr (Preferred Frequency Layer for CS voice HSPA Streaming)
1059
PrefLayerCSHSStr (Preferred Layer for CS voice HSPA Streaming) 1060
PFLChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 1061
PFLDBHSDAMR (Preferred Frequency Layer for DB-DC-HSDPA AMR)
1063
PrefLayerDBHSDAMR (Preferred Layer for DB-DC-HSDPA AMR) . 1063
PFLDBHSDAMRNRT (Preferred Frequency Layer for DB-DC-HSDPA
AMR and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1065
PrefLayerDBHSDAMRNRT (Preferred Layer for DB-DC-HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1066
PFLDBHSDNRT (Preferred Frequency Layer for DB-DC-HSDPA NRT) .
1067
PrefLayerDBHSDNRT (Preferred Layer for DB-DC-HSDPA NRT) . 1067
PFLDBHSDStr (Preferred Frequency Layer for DB-DC-HSDPA
Streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069
PrefLayerDBHSDStr (Preferred Layer for DB-DC-HSDPA Streaming) . .
1069
PFLDCHSDAMR (Preferred Frequency Layer for DC-HSDPA AMR) 1070
PrefLayerDCHSDAMR (Preferred Layer for DC-HSDPA AMR) . . . . 1071
PFLDCHSDAMRNRT (Preferred Frequency Layer for DC-HSDPA AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1072
PrefLayerDCHSDAMRNRT (Preferred Layer for DC-HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1073
PFLDCHSDNRT (Preferred Frequency Layer for DC-HSDPA NRT) 1074
PrefLayerDCHSDNRT (Preferred Layer for DC-HSDPA NRT) . . . . 1075
PFLDCHSDStr (Preferred Frequency Layer for DC-HSDPA Streaming) .
1076
PrefLayerDCHSDStr (Preferred Layer for DC-HSDPA Streaming) . 1077
PFLDCMIAMR (Preferred Frequency Layer for DC and MIMO AMR) . . .
1078
PrefLayerDCMIAMR (Preferred Layer for DC and MIMO AMR) . . . . 1079
PFLDCMIAMRNRT (Preferred Frequency Layer for DC and MIMO AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1080
PrefLayerDCMIAMRNRT (Preferred Layer for DC and MIMO AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1081
PFLDCMINRT (Preferred Frequency Layer for DC and MIMO NRT) 1082
PrefLayerDCMINRT (Preferred Layer for DC and MIMO NRT) . . . . 1083
PFLDCMIStr (Preferred Frequency Layer for DC and MIMO Streaming) .
1084
PrefLayerDCMIStr (Preferred Layer for DC and MIMO Streaming) . 1085
PFLFDPCHAMR (Preferred Frequency Layer for FDPCH AMR) . . . 1086
PrefLayerFDPCHAMR (Preferred Layer for F-DPCH AMR) . . . . . . . 1087
PFLFDPCHAMRNRT (Preferred Frequency Layer for FDPCH AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1088
PrefLayerFDPCHAMRNRT (Preferred Layer for F-DPCH AMR and NRT)
1089
Id:0900d805809d7397
113
WCDMA Radio Network Configuration Parameters
Table 585
Table 586
Table 587
Table 588
Table 589
Table 590
Table 591
Table 592
Table 593
Table 594
Table 595
Table 596
Table 597
Table 598
Table 599
Table 600
Table 601
Table 602
Table 603
Table 604
Table 605
Table 606
Table 607
Table 608
Table 609
Table 610
Table 611
Table 612
Table 613
Table 614
Table 615
Table 616
Table 617
Table 618
Table 619
Table 620
Table 621
Table 622
Table 623
114
PFLFDPCHNRT (Preferred Frequency Layer for FDPCH NRT) . . . . 1090
PrefLayerFDPCHNRT (Preferred Layer for F-DPCH NRT) . . . . . . . . 1091
PFLFDPCHStr (Preferred Frequency Layer for FDPCH Streaming) . 1092
PrefLayerFDPCHStr (Preferred Layer for F-DPCH Streaming) . . . . . 1093
PFLFastMovUECS (Preferred Frequency Layer for fast moving UE CS) .
1094
PrefLayerFastMovUECS (Preferred Layer for fast moving UE CS) . . 1095
PFLFastMovUEPS (Preferred Frequency Layer for fast moving UE PS) .
1096
PrefLayerFastMovUEPS (Preferred Layer for fast moving UE PS) . . 1097
PFLHSDPAAMR (Preferred Frequency Layer for HSDPA AMR) . . . 1098
PrefLayerHSDPAAMR (Preferred Layer for HSDPA AMR) . . . . . . . . 1099
PFLHSDPAAMRNRT (Preferred Frequency Layer for HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100
PrefLayerHSDPAAMRNRT (Preferred Layer for HSDPA AMR and NRT)
1101
PFLHSDPANRT (Preferred Frequency Layer for HSDPA NRT) . . . . 1102
PrefLayerHSDPANRT (Preferred Layer for HSDPA NRT) . . . . . . . . 1103
PFLHSDPAStr (Preferred Frequency Layer for HSDPA Streaming) . 1104
PrefLayerHSDPAStr (Preferred Layer for HSDPA Streaming) . . . . . 1105
PFLHSPAAMR (Preferred Frequency Layer for HSPA AMR) . . . . . . 1106
PrefLayerHSPAAMR (Preferred Layer for HSPA AMR) . . . . . . . . . . 1107
PFLHSPAAMRNRT (Preferred Frequency Layer for HSPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1108
PrefLayerHSPAAMRNRT (Preferred Layer for HSPA AMR and NRT) . . .
1109
PFLHSPANRT (Preferred Frequency Layer for HSPA NRT) . . . . . . 1110
PrefLayerHSPANRT (Preferred Layer for HSPA NRT) . . . . . . . . . . . 1111
PFLHSPAStr (Preferred Frequency Layer for HSPA Streaming) . . . 1112
PrefLayerHSPAStr (Preferred Layer for HSPA Streaming) . . . . . . . . 1113
PFLIdentifier (PFL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1114
PFLMIMOAMR (Preferred Frequency Layer for MIMO AMR) . . . . . . 1115
PrefLayerMIMOAMR (Preferred Layer for MIMO AMR) . . . . . . . . . . 1116
PFLMIMOAMRNRT (Preferred Frequency Layer for MIMO AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1117
PrefLayerMIMOAMRNRT (Preferred Layer for MIMO AMR and NRT) . . .
1118
PFLMIMONRT (Preferred Frequency Layer for MIMO NRT) . . . . . . 1119
PrefLayerMIMONRT (Preferred Layer for MIMO NRT) . . . . . . . . . . . 1120
PFLMIMOStr (Preferred Frequency Layer for MIMO Streaming) . . . 1121
PrefLayerMIMOStr (Preferred Layer for MIMO Streaming) . . . . . . . . 1122
PFLR99AMR (Preferred Frequency Layer for R99 AMR) . . . . . . . . . 1123
PrefLayerR99AMR (Preferred Layer for R99 AMR) . . . . . . . . . . . . . . 1124
PFLR99AMRNRT (Preferred Frequency Layer for R99 AMR and NRT) . .
1125
PrefLayerR99AMRNRT (Preferred Layer for R99 AMR and NRT) . . 1126
PFLR99NRT (Preferred Frequency Layer for R99 NRT) . . . . . . . . . . 1127
PrefLayerR99NRT (Preferred Layer for R99 NRT) . . . . . . . . . . . . . . 1128
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 624
Table 625
Table 626
Table 627
Table 628
Table 629
Table 630
Table 631
Table 632
Table 633
Table 634
Table 635
Table 636
Table 637
Table 638
Table 639
Table 640
Table 641
Table 642
Table 643
Table 644
Table 645
Table 646
Table 647
Table 648
Table 649
Table 650
Table 651
Table 652
Table 653
Table 654
Table 655
Table 656
Table 657
Table 658
DN00211177
Issue 12B
PFLR99Str (Preferred Frequency Layer for R99 Streaming) . . . . . . 1129
PrefLayerR99Str (Preferred Layer for R99 Streaming) . . . . . . . . . . . 1130
AutoConnHWID (Auto Connection Hardware ID) . . . . . . . . . . . . . . . 1132
AutoConnSiteID (Auto Connection site ID) . . . . . . . . . . . . . . . . . . . . 1133
BTSID (BTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1134
PREBTSID (PREBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1135
TechnologyInformation (Technology Information) . . . . . . . . . . . . . . 1136
Version (Version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1137
AMRLoadTxPower (Indicator for downlink radio power load) . . . . . . 1138
AMRNumofReconf (AMRNumofReconf) . . . . . . . . . . . . . . . . . . . . . . 1139
AMRwinSizeSCload (AMRwinSizeSCload) . . . . . . . . . . . . . . . . . . . 1139
AdjustmentPeriod (Adjustment period time) . . . . . . . . . . . . . . . . . . . 1140
AdjustmentRatio (Adjustment ratio) . . . . . . . . . . . . . . . . . . . . . . . . . 1142
AutoACDecRestHysNRTQ (Automatic Access Class Decrease Restriction
Level Hysteresis for NRT queue length trigger) . . . . . . . . . . . . . . . . 1143
AutoACDecRestHysRTWP (Automatic Access Class Decrease Restriction
Level Hysteresis for Received Total Wideband Power trigg) . . . . . . 1144
AutoACIncRestHysNRTQ (Automatic Access Class Increase Restriction
Level Hysteresis for NRT queue length trigger) . . . . . . . . . . . . . . . . 1145
AutoACIncRestHysRTWP (Automatic Access Class Increase Restriction
Level Hysteresis for Received Total Wideband Powertrigge) . . . . . . 1146
AutoACMaxRestLevel (Automatic Access Class Maximum Restriction
Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1148
AutoACRLevelUpdInt (Automatic Access Class Restriction Level Update
Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149
AutoACRTrigRNCLoad (Automatic Access Class Restriction Trigger of
RNC Load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150
AutoACRestForCellPCH (Access Restriction for Cell_PCH state UE) . . .
1152
BitRateSetPSNRT (Bit rate set for PS NRT DCHs) . . . . . . . . . . . . . 1153
DCHSlopeOfTheCurve (DCH slope of the curve) . . . . . . . . . . . . . . . 1155
DLInLoopPCStepSizeCPC (DL inner loop PC step size for CPC users) .
1156
DLLoadSource (DL Load Source) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1157
DLmaxBitRatePerSF (Maximum DL bit rate per spreading factor) . . 1158
DLmaxBitRateSF128 (Maximum DL bit rate with spreading factor 128) .
1159
DLmaxBitRateSF16 (Maximum DL bit rate with spreading factor 16) 1161
DLmaxBitRateSF256 (Maximum DL bit rate with spreading factor 256) .
1162
DLmaxBitRateSF32 (Maximum DL bit rate with spreading factor 32) 1163
DLmaxBitRateSF64 (Maximum DL bit rate with spreading factor 64) 1164
DLpuncturingLimit (Downlink puncturing limit) . . . . . . . . . . . . . . . . . 1165
DownlinkInnerLoopPCStepSize (Power-adjusting step size in WCDMA
BTS for DL closed loop PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1167
DynHSUPABLERAlgTrgTime (Time to trigger Dyn HSUPA BLER
Algorithm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1168
DynHSUPABLERBurstDataRx (Retransmissions in Dyn HSUPA BLER for
Bursty Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1169
Id:0900d805809d7397
115
WCDMA Radio Network Configuration Parameters
Table 659
Table 660
Table 661
Table 662
Table 663
Table 664
Table 665
Table 666
Table 667
Table 668
Table 669
Table 670
Table 671
Table 672
Table 673
Table 674
Table 675
Table 676
Table 677
Table 678
Table 679
Table 680
Table 681
Table 682
Table 683
Table 684
Table 685
Table 686
116
DynHSUPABLERContDataRx10 (Retransmissions in Dyn HSUPA BLER
for Cont Data 10msTTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1170
DynHSUPABLERContDataRx2 (Retransmissions in Dyn HSUPA BLER for
Cont Data 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1172
DynHSUPABLERFrameWinSiz (Window size for FP Frames
Measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1173
DynHSUPABLERMaxRateThrB (Peak rate threshold for bursty data of Dyn
HSUPA BLER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1174
DynHSUPABLERMaxRateThrC10 (Peak rate thr for cont data of Dyn HSUPA BLER 10 ms TTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1175
DynHSUPABLERMaxRateThrC2 (Peak rate thr for cont data of Dyn HSUPA BLER 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1176
DynHSUPABLERPeakRateRx (Retransmissions in Dyn HSUPA BLER for
Peak data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1178
DynHSUPABLERThrBurstyTP (Bursty Data throughput threshold per TTI)
1179
DynHSUPABurstyPeriod (Bursty Period for Dyn HSUPA BLER) . . . 1180
EDCHSlopeOfTheCurve (EDCH slope of the curve) . . . . . . . . . . . . . 1181
ExpectReorderingPDCP (Expect Reordering for PDCP) . . . . . . . . . . 1182
FOLPCSIRTgtModInt (Faster OLPC SIR target modification interval) . . .
1183
FOLPCStepSizSIRTgt (Faster OLPC step size of SIR target changes) . .
1184
FmaxPeriodPDCP (F Max Period for PDCP) . . . . . . . . . . . . . . . . . . . 1186
FmaxTimePDCP (F Max Time for PDCP) . . . . . . . . . . . . . . . . . . . . . 1187
FreePtxSafetyMarginStr (Safety margin for free transmitted power for
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1188
GainFactorControlPartPRACHmessage (Gain factor for control part of
PRACH message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189
PrachBetaC120 (Gain factor for control part of PRACH message with 120
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1190
PrachBetaC15 (Gain factor for control part of PRACH message with 15
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1191
PrachBetaC30 (Gain factor for control part of PRACH message with 30
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1192
PrachBetaC60 (Gain factor for control part of PRACH message with 60
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1193
GainFactorDataPartPRACHmessage (Gain factor for data part of PRACH
message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1194
PrachBetaD120 (Gain factor for data part of PRACH message with 120
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1196
PrachBetaD15 (Gain factor for data part of PRACH message with 15 ksps)
1197
PrachBetaD30 (Gain factor for data part of PRACH message with 30 ksps)
1198
PrachBetaD60 (Gain factor for data part of PRACH message with 60 ksps)
1199
HSFACHDiscardTimer (Discard Timer for BCCH, CCCH and DCCH data
on HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200
HSFACHResetTimer (MAC-ehs Reset Timer for xCCH data on HS-FACH)
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 687
Table 688
Table 689
Table 690
Table 691
Table 692
Table 693
Table 694
Table 695
Table 696
Table 697
Table 698
Table 699
Table 700
Table 701
Table 702
Table 703
Table 704
Table 705
Table 706
Table 707
Table 708
Table 709
Table 710
Table 711
Table 712
Table 713
Table 714
Table 715
Table 716
Table 717
Table 718
Table 719
Table 720
DN00211177
Issue 12B
1201
HeaderCompressionMethod (Header compression algorithm of PDCP) .
1202
ICRHostOperatorId (ICR Host Operator Identifier) . . . . . . . . . . . . . . 1203
L1BurstDataBLERTrgtEDCH (Layer1 Bursty Data BLER target for EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1205
L1ContBLERTrgtEDCH10 (Layer1 Continuous BLER target for E-DCH TTI
10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1206
L1ContBLERTrgtEDCH2 (Layer1 Continuous BLER target for E-DCH TTI
2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1207
L1PeakRateBLERTrgtEDCH (Layer1 Peak Data Rate BLER target for EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1209
LoadBasedAMRCodecMode (Usage of Load based AMR codec mode
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1210
MaxAdjustmentStep (Maximum adjustment step) . . . . . . . . . . . . . . 1211
MaxFreezingTime (Maximum freezing time) . . . . . . . . . . . . . . . . . . . 1212
MaxHeaderPDCP (Max Header for PDCP) . . . . . . . . . . . . . . . . . . . 1213
MaxNumberOfReAttemptsCong (Maximum number of re-attempts to hunt
resources) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1214
MinPrefChange (Trigger for sending the updated reference power to
BTSs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1215
NonTCPspacePDCP (Non-TCP Space for PDCP) . . . . . . . . . . . . . . 1217
PCPreamble (Uplink DPCCH power control preamble) . . . . . . . . . . 1218
PCrangeDL (Radio link downlink power control range) . . . . . . . . . . 1219
PTTUEMappingARPCap (PTT UE mapping for ARP pre-emption
capability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1220
PTTUEMappingARPPrioLevel (PTT UE mapping for ARP priority level) .
1222
PTTUEMappingARPQue (PTT UE Mapping for ARP queuing allowed) . .
1224
PTTUEMappingARPVul (PTT UE mapping for ARP pre-emption
vulnerability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1225
PTTUEMappingSignInd (PTT UE mapping for Signaling indication) 1227
PTTUEMappingTC (PTT UE mapping for Traffic Class) . . . . . . . . . 1229
PTTUEMappingTHP (PTT UE mapping for Traffic handling priority) 1230
PagingRestrictionInd (Paging Restriction Indication for PPAC) . . . . 1232
PeriodULRCAMR (Period for CS AMR RRC TFC control requests) 1233
PrefSubtract (Reference power subtraction parameter) . . . . . . . . . . 1235
RAU_LAU_RestrictionInd (RAU and LAU Restriction Indication for PPAC)
1236
RNACChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 1237
RNACId (RNAC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1238
RNARDSACCell_DCH (Access class restriction level for Cell_DCH) 1239
RNARDSACCell_PCH (Access class restriction level for Cell_PCH) 1241
RNARDSACGuardTime (Access class restriction guard time) . . . . . 1242
RRCConnSetupMsgSize (RRC Connection Setup Message Size
Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1243
SRBDelay (SRB delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1245
SignallingLinkInactivityTimer (Signalling link inactivity timer) . . . . . . 1246
Id:0900d805809d7397
117
WCDMA Radio Network Configuration Parameters
Table 721
Table 722
Table 723
Table 724
Table 725
Table 726
Table 727
Table 728
Table 729
Table 730
Table 731
Table 732
Table 733
Table 734
Table 735
Table 736
Table 737
Table 738
Table 739
Table 740
Table 741
Table 742
Table 743
Table 744
Table 745
Table 746
Table 747
Table 748
Table 749
Table 750
Table 751
Table 752
Table 753
Table 754
Table 755
Table 756
Table 757
Table 758
Table 759
118
StepSizeForDCHBLER (Step Size for DCH BLER calculation) . . . . . 1247
StepSizeForEDCHBLER (Step Size for EDCH BLER calculation) . . 1248
TCPspacePDCP (TCP Space for PDCP) . . . . . . . . . . . . . . . . . . . . . 1249
TDMultForHSDPAStreaming (Transfer Delay multiplier for HSDPA
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250
TFDCHZeroBitRate (Zero size transport block to L1 CRC calculation) . . .
1251
ULFastOLPCDTXthld (DTX threshold for uplink faster outer loop) . . 1253
ULmaxBitRatePerSF (Maximum UL bit rate per spreading factor) . . 1254
ULmaxBitRateSF128 (Maximum UL bit rate with spreading factor 128) . .
1255
ULmaxBitRateSF16 (Maximum UL bit rate with spreading factor 16) 1256
ULmaxBitRateSF256 (Maximum UL bit rate with spreading factor 256) . .
1257
ULmaxBitRateSF32 (Maximum UL bit rate with spreading factor 32) 1258
ULmaxBitRateSF64 (Maximum UL bit rate with spreading factor 64) 1260
ULmaxBitRateSF8 (Maximum UL bit rate with spreading factor 8) . . 1261
ULpuncturingLimit (Uplink puncturing limit) . . . . . . . . . . . . . . . . . . . . 1262
UlScrCodeMin (Uplink scrambling code minimum value) . . . . . . . . . 1263
UpLinkInitialTransmitPowerMode (Initial transmit power in uplink compressed mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1265
UpLinkRecoveryPeriodPowerMode (Recovery Period Power in UL Compressed Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1266
AlarmSetforWCELBLINIT (Alarm Set for WCEL BL-INIT) . . . . . . . . . 1268
CBCSourceIPAddress (Source IP address for IuBC interface) . . . . . 1269
CSAttachDetachAllowed (Attach-detach allowed) . . . . . . . . . . . . . . . 1270
CommonMCC (Common MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1271
CommonMNC (Common MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1272
CommonMNCLength (Common MNC Length) . . . . . . . . . . . . . . . . . 1273
ConnectionRetryCounter (OAM Connection Establishment Retry Counter)
1274
DLBLERConfInterval (Downlink measured BLER confidence interval) . . .
1275
DSCPStatisticsGroupA (DSCP statistics group A ) . . . . . . . . . . . . . . 1277
DSCPStatisticsGroupB (DSCP statistics group B) . . . . . . . . . . . . . . 1278
DSCPStatisticsGroupC (DSCP statistics group C) . . . . . . . . . . . . . . 1279
DSCPStatisticsGroupTCPack (DSCP code for DL TCP Ack statistics) . . .
1280
EmergencyCallRedirectTimer (Emergency Call Redirect Timer) . . . . 1282
ExtendedULDLactivationTmr (Extended Cell_FACH inactivity supervision
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1283
LCSSupportForAnchoring (LCS Support for Anchoring) . . . . . . . . . . 1284
LCSfunctionality (LCS functionality) . . . . . . . . . . . . . . . . . . . . . . . . . . 1285
MACLogicalChPriority (MAC logical channel priority definition) . . . . 1286
MACLogChPriSRB1 (MAC logical channel priority for SRB1) . . . . . . 1287
MACLogChPriSRB2 (MAC logical channel priority for SRB2) . . . . . . 1288
MACLogChPriSRB3 (MAC logical channel priority for SRB3) . . . . . . 1288
N302 (N302) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1289
N304 (N304) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1290
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 760
Table 761
Table 762
Table 763
Table 764
Table 765
Table 766
Table 767
Table 768
Table 769
Table 770
Table 771
Table 772
Table 773
Table 774
Table 775
Table 776
Table 777
Table 778
Table 779
Table 780
Table 781
Table 782
Table 783
Table 784
Table 785
Table 786
Table 787
Table 788
Table 789
Table 790
Table 791
Table 792
Table 793
Table 794
Table 795
Table 796
Table 797
Table 798
Table 799
Table 800
DN00211177
Issue 12B
N308 (N308) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1291
OMSBackupIpAddress (OMS Backup IP Address) . . . . . . . . . . . . . 1292
OMSIpAddress (OMS IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 1293
PWSMDuration (Duration of low traffic for cell shutdown) . . . . . . . . 1294
PWSMExceededTrafficDur (Time limit for traffic to activate a shutdown
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1295
PageRep1stInterv (Repetition interval of the first repeated connected
mode paging procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1296
PageRep2ndInterv (Repetition interval of the second repeated connected
mode paging procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1298
RANAPprocInitWait (RANAP initiation timer) . . . . . . . . . . . . . . . . . . 1299
RNCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 1300
RNCIPAddress (RNC IP-address) . . . . . . . . . . . . . . . . . . . . . . . . . . 1302
RNCName (RNC name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1303
RTservicesForPS (PS domain RT service) . . . . . . . . . . . . . . . . . . . . 1304
RestrictionInterval (Restriction Interval) . . . . . . . . . . . . . . . . . . . . . . 1305
RncClientTLSMode (RNC Client TLS Mode) . . . . . . . . . . . . . . . . . . 1306
RncId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1307
RncOptions (RNC Options) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1308
SIB11_priority (Priority for SIB11) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1315
SIB15_priority (Priority for SIB15) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1316
SIB18_priority (Priority for SIB18) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1317
SIB19Priority (Priority for SIB19) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1318
SIB1_priority (Priority for SIB1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1319
SIB2_priority (Priority for SIB2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1320
SIB3_priority (Priority for SIB3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1321
SIB5_priority (Priority for SIB5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1322
SecOMSIpAddress (Secondary OMS IP address) . . . . . . . . . . . . . . 1323
ServingOMS (Serving OMS ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1324
ServingOMSAdminSetting (Serving OMS Admin Setting) . . . . . . . . 1326
ServingOMSSwoRequest (Serving OMS Switchover Request) . . . . 1327
T302 (T302) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1329
T304 (T304) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1330
T305 (T305) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1331
T307 (T307) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1332
T308 (T308) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1333
T309 (T309) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1335
T314 (T314) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1335
T316 (T316) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1337
T317 (T317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1338
ToAWE_NRT_DCH_tti10 (Time of Arrival Window Endpoint for NRT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1339
ToAWE_NRT_DCH_tti20 (Time of Arrival Window Endpoint for NRT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1340
ToAWE_NRT_DCH_tti40 (Time of Arrival Window Endpoint for NRT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1341
ToAWE_RT_DCH_tti10 (Time of Arrival Window Endpoint for RT DCH (TTI
10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1343
Id:0900d805809d7397
119
WCDMA Radio Network Configuration Parameters
Table 801
Table 802
Table 803
Table 804
Table 805
Table 806
Table 807
Table 808
Table 809
Table 810
Table 811
Table 812
Table 813
Table 814
Table 815
Table 816
Table 817
Table 818
Table 819
Table 820
Table 821
Table 822
Table 823
Table 824
Table 825
Table 826
Table 827
Table 828
Table 829
Table 830
Table 831
Table 832
Table 833
120
ToAWE_RT_DCH_tti20 (Time of Arrival Window Endpoint for RT DCH (TTI
20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1344
ToAWE_RT_DCH_tti40 (Time of Arrival Window Endpoint for RT DCH (TTI
40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1345
ToAWE_Speech (Time of Arrival Window Endpoint for speech services) .
1346
ToAWS_NRT_DCH_tti10 (Time of Arrival Window Startpoint for NRT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1347
ToAWS_NRT_DCH_tti20 (Time of Arrival Window Startpoint for NRT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1348
ToAWS_NRT_DCH_tti40 (Time of Arrival Window Startpoint for NRT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1349
ToAWS_RT_DCH_tti10 (Time of Arrival Window Startpoint for RT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1350
ToAWS_RT_DCH_tti20 (Time of Arrival Window Startpoint for RT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1351
ToAWS_RT_DCH_tti40 (Time of Arrival Window Startpoint for RT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1352
ToAWS_Speech (Time of Arrival Window Startpoint for speech services)
1353
TraceLCSHorizAccur (Trace LCS Horizontal Accuracy) . . . . . . . . . . 1354
TraceLCSPriority (Trace LCS Priority) . . . . . . . . . . . . . . . . . . . . . . . . 1355
TraceLCSVertAccur (Trace LCS Vertical Accuracy) . . . . . . . . . . . . . 1356
TraceLCSWaitPeriod (Trace LCS Wait Period) . . . . . . . . . . . . . . . . . 1357
ULBLERConfInterval (Uplink measured BLER confidence interval) . 1358
UL_DLcapacityReqWait (Waiting time for UL/DL capacity request) . 1359
UePeriodicMeasCpuLimit (UE Periodic Measurement Report CPU Limit)
1361
UePeriodicMeasInterval (UE Periodic Measurement Report Measurements Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1362
WCELIdleAlarmTimeout (WCEL Idle Alarm Timeout) . . . . . . . . . . . . 1363
AMRWithEDCH (Usage of AMR service with E-DCH) . . . . . . . . . . . . 1365
AMRWithHSDSCH (Usage of AMR service with HS-DSCH) . . . . . . . 1366
AutoACResEnabled (Automatic Access Class Restriction Enabled) . 1368
AutomDLPlanUpdEnabled (Automatic DL Plan update enabled) . . . 1370
CCCHforCUCallowed (Usage of CCCH for Cell/URA Update Confirm
allowed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1371
CMmasterSwitch (Compressed mode master switch) . . . . . . . . . . . . 1372
CSFBEnabled (CSFB Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1373
CUCforPCHtoDCHallowed (Direct State Transition From Cell_PCH to
Cell_DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1374
CVUserInactInSignConnRel (Cause value usage in NAS signaling connection release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1375
CapaSmartphoneEnabled (Capacity Increase for Smartphones Enabled)
1377
DCH00SuppOnIurEnabled (DCH 0/0 Support On Iur Enabled) . . . . . 1378
DCHBitRateBalancing (DCH bit rate balancing on/off switch) . . . . . . 1379
DCHScheOverIur (DCH Scheduling Over Iur) . . . . . . . . . . . . . . . . . . 1380
DCHtoPCHEnabled (Enabling direct Cell_DCH to PCH state transition) .
1380
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 834
Table 835
Table 836
Table 837
Table 838
Table 839
Table 840
Table 841
Table 842
Table 843
Table 844
Table 845
Table 846
Table 847
Table 848
Table 849
Table 850
Table 851
Table 852
Table 853
Table 854
Table 855
Table 856
Table 857
Table 858
Table 859
Table 860
Table 861
Table 862
Table 863
Table 864
Table 865
Table 866
Table 867
Table 868
Table 869
Table 870
DN00211177
Issue 12B
DLOptimisationUsage (Dynamic link optimisation usage) . . . . . . . . 1381
DynUsageHSDPAReturnChannel (Dynamic usage of UL NRT DCH HSDPA return Channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1383
EUTRAdetection (E-UTRA detection) . . . . . . . . . . . . . . . . . . . . . . . . 1384
EmergencyCallISHOSupport (Emergency Call lSHO Support) . . . . 1385
EmergencyCallRedirect (Emergency Call Redirect) . . . . . . . . . . . . . 1386
FRLCEnabled (Flexible RLC Enabled) . . . . . . . . . . . . . . . . . . . . . . . 1387
FastDormancyEnabled (Fast Dormancy activation / de-activation
parameter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1388
FastPCHSwitchEnabled (Enabling Fast Cell_PCH Switching feature) . . .
1389
FasterOLPCEnabled (Faster OLPC Enabled) . . . . . . . . . . . . . . . . . 1391
FemtoHandoverControl (Femto Handover Control) . . . . . . . . . . . . . 1392
FlexULRLCEnabled (Flexible UL RLC Enabled) . . . . . . . . . . . . . . . 1393
FlexUpgrUsage (Usage of the Flexible Upgrade of the NRT DCH data
rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1394
HLSModeSelection (Higher Layer Scheduling mode selection) . . . . 1396
HSDPA16KBPSReturnChannel (HSDPA 16 kbps UL DCH return channel
on/off switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1397
HSDPA48UsersEnabled (HSDPA 48 users enabled) . . . . . . . . . . . . 1398
HSDPADynamicResourceAllocation (HSDPA Dynamic Resource
Allocation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400
HSDPAMobility (Serving HS-DSCH cell change and SHO on/off switch)
1401
HSPAInterRNCMobility (HSPA Inter-RNC Mobility) . . . . . . . . . . . . . 1402
HSPAOverIurExt (HSPA Over Iur Extension) . . . . . . . . . . . . . . . . . . 1404
HSUPADynBLEREnabled (HSUPA Dynamic BLER Enabled) . . . . . 1405
IFHOOverIurExt (IFHO Over Iur Extension) . . . . . . . . . . . . . . . . . . . 1406
ISHOCancellation (Inter-System Handover Cancellation) . . . . . . . . 1407
ISHOInIurMobility (ISHO In Iur Mobility) . . . . . . . . . . . . . . . . . . . . . . 1408
IntelligentEmergencyCallISHOSupport (Intelligent Emergency Call ISHO
Support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1409
IuPSrelWait3G2GMultiServ (Time supervision for releasing Iu-PS
connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410
LFDProfEnabled (LFD profiling Enabled) . . . . . . . . . . . . . . . . . . . . . 1412
MIBPLMNIdIncluded (MIB PLMN Identity Included) . . . . . . . . . . . . . 1412
MOCNenabled (Multi-Operator Core Network enabled) . . . . . . . . . . 1414
PBSpolicy (Priority based scheduling policy) . . . . . . . . . . . . . . . . . . 1415
PPACEnabled (Paging Permission With Access Control Enabled) . 1417
PSOpThroUsage (Throughput based optimisation of the PS algorithm
usage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1419
PTTEnabled (Push to talk enabled) . . . . . . . . . . . . . . . . . . . . . . . . . 1421
PWSMDriftAllowed (Cell shutdown allowed with drifting UE) . . . . . . 1423
PostVerifPeriodDLSynch (Post-verification period in downlink
synchronization) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1424
PowerBalancing (Power Balancing on/off) . . . . . . . . . . . . . . . . . . . . 1425
RABDRAEnabled (Usage of the direct resource allocation for PS NRT
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1427
RNFCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 1429
Id:0900d805809d7397
121
WCDMA Radio Network Configuration Parameters
Table 871
Table 872
Table 873
Table 874
Table 875
Table 876
Table 877
Table 878
Table 879
Table 880
Table 881
Table 882
Table 883
Table 884
Table 885
Table 886
Table 887
Table 888
Table 889
Table 890
Table 891
Table 892
Table 893
Table 894
Table 895
Table 896
Table 897
Table 898
Table 899
Table 900
Table 901
Table 902
Table 903
Table 904
Table 905
Table 906
Table 907
Table 908
Table 909
Table 910
Table 911
Table 912
122
RNFCId (RNFC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1430
RRCSetupCCHEnabledR99 (RRC setup on CCH enabled for R99 UE) . .
1431
SLHOCmAllowedNRT (CM allowed for NRT connection in SLHO) . . 1433
SRVCCEnabled (SRVCC Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 1433
SignConnActivitySupervision (Activity supervision for NAS signaling
connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1435
WPSCallRestriction (Restricting overloaded WPS calls) . . . . . . . . . . 1437
WireLessPriorityService (Usage of the Wireless Priority Service) . . . 1439
AARConfigTable (Application Aware RAN Configuration Table) . . . . 1441
AppGrpId (Application Group Identifier) . . . . . . . . . . . . . . . . . . . . . . . 1442
DSCPCode1 (DSCP Code1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1443
DSCPCode2 (DSCP Code2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1445
DSCPCode3 (DSCP Code3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1446
DSCPCode4 (DSCP Code4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1448
DSCPCode5 (DSCP Code5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1449
Precedence (Precedence) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1450
TargetSPIforSPI0 (Target SPI for SPI 0) . . . . . . . . . . . . . . . . . . . . . . 1451
TargetSPIforSPI1 (Target SPI for SPI 1) . . . . . . . . . . . . . . . . . . . . . . 1453
TargetSPIforSPI10 (Target SPI for SPI 10) . . . . . . . . . . . . . . . . . . . . 1455
TargetSPIforSPI11 (Target SPI for SPI 11) . . . . . . . . . . . . . . . . . . . . 1456
TargetSPIforSPI2 (Target SPI for SPI 2 ) . . . . . . . . . . . . . . . . . . . . . 1458
TargetSPIforSPI3 (Target SPI for SPI 3 ) . . . . . . . . . . . . . . . . . . . . . 1460
TargetSPIforSPI4 (Target SPI for SPI 4) . . . . . . . . . . . . . . . . . . . . . . 1461
TargetSPIforSPI5 (Target SPI for SPI 5) . . . . . . . . . . . . . . . . . . . . . . 1463
TargetSPIforSPI6 (Target SPI for SPI 6) . . . . . . . . . . . . . . . . . . . . . . 1465
TargetSPIforSPI7 (Target SPI for SPI 7) . . . . . . . . . . . . . . . . . . . . . . 1466
TargetSPIforSPI8 (Target SPI for SPI 8) . . . . . . . . . . . . . . . . . . . . . . 1468
TargetSPIforSPI9 (Target SPI for SPI 9) . . . . . . . . . . . . . . . . . . . . . . 1470
ARPWeight (ARP based weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1471
WeightForARP1 (Weight for ARP1) . . . . . . . . . . . . . . . . . . . . . . . . . . 1473
WeightForARP2 (Weight for ARP2) . . . . . . . . . . . . . . . . . . . . . . . . . . 1474
WeightForARP3 (Weight for ARP3) . . . . . . . . . . . . . . . . . . . . . . . . . . 1475
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA) . . 1476
CPCNRT10msTTI (CPC NRT 10 ms TTI) . . . . . . . . . . . . . . . . . . . . . 1477
N10msCPCOptObjective (CPC Optimization objective NRT 10ms TTI) . .
1478
N10msCQIDTXTimer (CQI DTX Timer NRT 10ms TTI) . . . . . . . . . . 1479
N10msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 10ms TTI)
1481
N10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle NRT
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1482
N10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 NRT
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1483
N10msMACDTXCycle (MAC DTX Cycle NRT 10ms TTI) . . . . . . . . . 1485
N10msMACInacThr (MAC Inactivity Threshold NRT 10ms TTI) . . . . 1486
N10msUEDPCCHburst1 (UE DPCCH burst1 NRT 10ms TTI) . . . . . 1487
N10msUEDPCCHburst2 (UE DPCCH burst2 NRT 10ms TTI) . . . . . 1488
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 913
Table 914
Table 915
Table 916
Table 917
Table 918
Table 919
Table 920
Table 921
Table 922
Table 923
Table 924
Table 925
Table 926
Table 927
Table 928
Table 929
Table 930
Table 931
Table 932
Table 933
Table 934
Table 935
Table 936
Table 937
Table 938
Table 939
Table 940
Table 941
Table 942
Table 943
Table 944
Table 945
Table 946
Table 947
Table 948
Table 949
Table 950
DN00211177
Issue 12B
N10msUEDRXCycle (UE DRX Cycle NRT 10ms TTI) . . . . . . . . . . . 1489
N10msUEDTXCycle1 (UE DTX Cycle 1 NRT 10ms TTI) . . . . . . . . . 1490
N10msUEDTXCycle2 (UE DTX Cycle 2 NRT 10ms TTI) . . . . . . . . . 1492
N10msUEDTXLongPreamble (UE DTX Long Preamble N10ms) . . . 1493
CPCNRT2msTTI (CPC NRT 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . 1494
N2msCPCOptObjective (CPC Optimization objective NRT 2ms TTI) 1495
N2msCQIDTXTimer (CQI DTX Timer NRT 2ms TTI) . . . . . . . . . . . . 1496
N2msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 2ms TTI) .
1498
N2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle NRT
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1499
N2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 NRT
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1501
N2msMACDTXCycle (MAC DTX Cycle NRT 2ms TTI) . . . . . . . . . . 1502
N2msMACInacThr (MAC Inactivity Threshold NRT 2ms TTI) . . . . . 1503
N2msUEDPCCHburst1 (UE DPCCH burst1 NRT 2ms TTI) . . . . . . . 1505
N2msUEDPCCHburst2 (UE DPCCH burst2 NRT 2ms TTI) . . . . . . . 1506
N2msUEDRXCycle (UE DRX Cycle NRT 2ms TTI) . . . . . . . . . . . . . 1507
N2msUEDTXCycle1 (UE DTX Cycle 1 NRT 2ms TTI) . . . . . . . . . . . 1508
N2msUEDTXCycle2 (UE DTX Cycle 2 NRT 2ms TTI) . . . . . . . . . . . 1509
N2msUEDTXLongPreamble (UE DTX Long Preamble NRT 2ms TTI) . .
1511
CPCStreaming10msTTI (CPC Streaming 10 ms TTI) . . . . . . . . . . . 1512
S10msCPCOptObjective (CPC Optimization objective Str 10ms TTI) . . .
1513
S10msCQIDTXTimer (CQI DTX Timer Str 10ms TTI) . . . . . . . . . . . 1514
S10msCQIFeedbackCPC (CQI Feedback Cycle for CPC Str 10ms TTI) .
1516
S10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Str
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1517
S10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Str
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1518
S10msMACDTXCycle (MAC DTX Cycle Str 10ms TTI) . . . . . . . . . . 1520
S10msMACInacThr (MAC Inactivity Threshold Str 10ms TTI) . . . . . 1521
S10msUEDPCCHburst1 (UE DPCCH burst1 Str 10ms TTI) . . . . . . 1522
S10msUEDPCCHburst2 (UE DPCCH burst2 Str 10ms TTI) . . . . . . 1523
S10msUEDRXCycle (UE DRX Cycle Str 10ms TTI) . . . . . . . . . . . . 1524
S10msUEDTXCycle1 (UE DTX Cycle 1 Str 10ms TTI) . . . . . . . . . . 1525
S10msUEDTXCycle2 (UE DTX Cycle 2 Str 10ms TTI) . . . . . . . . . . 1527
S10msUEDTXLongPreamble (UE DTX Long Preamble Str 10ms TTI) . .
1528
CPCStreaming2msTTI (CPC Streaming 2 ms TTI) . . . . . . . . . . . . . 1529
S2msCPCOptObjective (CPC Optimization objective Str 2ms TTI) . 1530
S2msCQIDTXTimer (CQI DTX Timer Str 2ms TTI) . . . . . . . . . . . . . 1531
S2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Str 2ms TTI) . . .
1533
S2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Str
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1534
S2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Str
Id:0900d805809d7397
123
WCDMA Radio Network Configuration Parameters
Table 951
Table 952
Table 953
Table 954
Table 955
Table 956
Table 957
Table 958
Table 959
Table 960
Table 961
Table 962
Table 963
Table 964
Table 965
Table 966
Table 967
Table 968
Table 969
Table 970
Table 971
Table 972
Table 973
Table 974
Table 975
Table 976
Table 977
Table 978
Table 979
Table 980
Table 981
Table 982
Table 983
Table 984
Table 985
Table 986
Table 987
Table 988
124
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1535
S2msMACDTXCycle (MAC DTX Cycle Str 2ms TTI) . . . . . . . . . . . . 1537
S2msMACInacThr (MAC Inactivity Threshold Str 2ms TTI) . . . . . . . 1538
S2msUEDPCCHburst1 (UE DPCCH burst1 Str 2ms TTI) . . . . . . . . . 1539
S2msUEDPCCHburst2 (UE DPCCH burst2 Str 2ms TTI) . . . . . . . . . 1540
S2msUEDRXCycle (UE DRX Cycle Str 2ms TTI) . . . . . . . . . . . . . . . 1541
S2msUEDTXCycle1 (UE DTX Cycle 1 Str 2ms TTI) . . . . . . . . . . . . . 1542
S2msUEDTXCycle2 (UE DTX Cycle 2 Str 2ms TTI) . . . . . . . . . . . . . 1544
S2msUEDTXLongPreamble (UE DTX Long Preamble Str 2ms TTI) 1545
CPCVoice10msTTI (CPC Voice 10 ms TTI) . . . . . . . . . . . . . . . . . . . 1546
V10msCPCOptObjective (CPC Optimization objective Voi 10ms TTI) . . .
1548
V10msCQIDTXTimer (CQI DTX Timer Voi 10ms TTI) . . . . . . . . . . . 1549
V10msCQIFeedbackCPC (CQI Feedback Cycle for CPC Voi 10ms TTI) .
1550
V10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Voi
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1552
V10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Voi
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1553
V10msMACDTXCycle (MAC DTX Cycle Voi 10ms TTI) . . . . . . . . . . 1554
V10msMACInacThr (MAC Inactivity Threshold Voi 10ms TTI) . . . . . 1555
V10msUEDPCCHburst1 (UE DPCCH burst1 Voi 10ms TTI) . . . . . . 1557
V10msUEDPCCHburst2 (UE DPCCH burst2 Voi 10ms TTI) . . . . . . 1558
V10msUEDRXCycle (UE DRX Cycle Voi 10ms TTI) . . . . . . . . . . . . . 1559
V10msUEDTXCycle1 (UE DTX Cycle 1 Voi 10ms TTI) . . . . . . . . . . . 1560
V10msUEDTXCycle2 (UE DTX Cycle 2 Voi 10ms TTI) . . . . . . . . . . . 1561
V10msUEDTXLongPreamble (UE DTX Long Preamble Voi 10ms TTI) . .
1562
CPCVoice2msTTI (CPC Voice 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . 1563
V2msCPCOptObjective (CPC Optimization objective Voi 2ms TTI) . 1565
V2msCQIDTXTimer (CQI DTX Timer Voi 2ms TTI) . . . . . . . . . . . . . 1566
V2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Voi 2ms TTI) . . .
1567
V2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Voi
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1568
V2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Voi
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1570
V2msMACDTXCycle (MAC DTX Cycle Voi 2ms TTI) . . . . . . . . . . . . 1571
V2msMACInacThr (MAC Inactivity Threshold Voi 2ms TTI) . . . . . . . 1572
V2msUEDPCCHburst1 (UE DPCCH burst1 Voi 2ms TTI) . . . . . . . . 1574
V2msUEDPCCHburst2 (UE DPCCH burst2 Voi 2ms TTI) . . . . . . . . 1575
V2msUEDRXCycle (UE DRX Cycle Voi 2ms TTI) . . . . . . . . . . . . . . . 1576
V2msUEDTXCycle1 (UE DTX Cycle 1 Voi 2ms TTI) . . . . . . . . . . . . . 1577
V2msUEDTXCycle2 (UE DTX Cycle 2 Voi 2ms TTI) . . . . . . . . . . . . . 1578
V2msUEDTXLongPreamble (UE DTX Long Preamble Voi 2ms TTI) 1580
CPICHECNOSRBHSPA (CPICH EcNo for SRB on HSPA) . . . . . . . 1581
CPICHECNOThreEDCH2MS (CPICH ECNO Threshold for E-DCH TTI 2
ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1582
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 989
CPICHRSCPThreEDCH2MS (CPICH RSCP Threshold for E-DCH TTI 2
ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1583
Table 990 CPICHRSCPThreSRBHSDPA (CPICH RSCP Threshold for SRBs on
HSDPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1584
Table 991 DCellVsMIMOPreference (Dual Cell versus MIMO preference) . . . . 1584
Table 992 DiscardTimerHSCSVoice (HSDPA Discard Timer for the CS voice
service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1586
Table 993 DiscardTimerPTT (HSDPA Discard Timer for the PTT) . . . . . . . . . . 1587
Table 994 EDCHCTSwitchGuardTimer (E-DCH channel type switch guard timer) . .
1588
Table 995 EDCHMACdflowtputStrTtT (Low throughput time to trigger for streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1589
Table 996 EDCHMaxHARQReTxStr (E-DCH max number of HARQ retransmissions
for streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1591
Table 997 EDCHMaxHarqReTxSRB (E-DCH maximum # of HARQ retransmissions
for 10 ms SRB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1592
Table 998 EDCHMaxHarqReTxSRB2MS (E-DCH maximum # of HARQ retransmissions for 2 ms SRB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1593
Table 999 EDCHMaxNumberOfHARQReTx (E-DCH maximum number of HARQ
retransmissions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1594
Table 1000 EDCHQOSClasses (E-DCH QoS classes) . . . . . . . . . . . . . . . . . . . . 1595
Table 1001 EnablDelayHHO (Enabling Delay HHO) . . . . . . . . . . . . . . . . . . . . . . 1596
Table 1002 EnablDelayStand (Enabling Delay Standard) . . . . . . . . . . . . . . . . . . 1597
Table 1003 FDPCHAllocMinInterval (Minimum interval between F-DPCH allocations)
1598
Table 1004 FDPCHAndSRBOnHSPATC (F-DPCH and SRBs on HSPA per TC) 1600
Table 1005 FDPCHSetupEC (DCH instead of F-DPCH based on Establishment
Cause) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1601
Table 1006 FactorEDCHMaxBRPSstream (Factor E-DCH max. Bit Rate for PS
streaming RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1603
Table 1007 FactorEDCHMaxBitRate (Factor to calculate EDCH maximum bit rate) .
1605
Table 1008 FactorEDCHMaxBitRate2NRT (Factor E-DCH max. Bit Rate for 2 NRT
RAB combinations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1606
Table 1009 FactorEDCHMaxBitRate3NRT (Factor E-DCH max. Bit Rate for 3 NRT
RAB combinations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1607
Table 1010 HSDPACPICHCTSRepPer (DCH to HS-DSCH switch CPICH Ec/No reporting period) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1608
Table 1011 HSDPACPICHEcNoThreshold (CPICH Ec/No threshold for serving HSDSCH cell change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1609
Table 1012 HSDPACellChangeRepetitionTime (Window for max repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1610
Table 1013 HSDPAChaTypeSwitchWindow (HSDPA channel type switching window)
1611
Table 1014 HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1612
Table 1015 HSDPAPeakRateLimitRABMax (HSDPA peak rate limitation to the RAB
maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1614
Table 1016 HSDPAPriority (HSDPA priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1615
Table 1017 HSDPARRCdiversity (SHO of the HSDPA capable UE) . . . . . . . . . 1617
DN00211177
Issue 12B
Id:0900d805809d7397
125
WCDMA Radio Network Configuration Parameters
Table 1018 HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1618
Table 1019 HSDSCHCTSwitchGuardTimer (HS-DSCH channel type switch guard
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1620
Table 1020 HSDSCHGuardTimerLowThroughput (HS-DSCH guard timer due to low
throughput) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1621
Table 1021 HSDSCHQoSclasses (HS-DSCH QoS classes) . . . . . . . . . . . . . . . . 1622
Table 1022 HSPANBRValues (HSPA NBR values) . . . . . . . . . . . . . . . . . . . . . . . 1623
Table 1023 NBRForPri0DL (Downlink NBR for Priority value 0) . . . . . . . . . . . . . 1625
Table 1024 NBRForPri0UL (Uplink NBR for Priority value 0) . . . . . . . . . . . . . . . . 1626
Table 1025 NBRForPri10DL (Downlink NBR for Priority value 10) . . . . . . . . . . . 1627
Table 1026 NBRForPri10UL (Uplink NBR for Priority value 10) . . . . . . . . . . . . . . 1628
Table 1027 NBRForPri11DL (Downlink NBR for Priority value 11) . . . . . . . . . . . 1629
Table 1028 NBRForPri11UL (Uplink NBR for Priority value 11) . . . . . . . . . . . . . . 1630
Table 1029 NBRForPri12DL (Downlink NBR for Priority value 12) . . . . . . . . . . . 1631
Table 1030 NBRForPri12UL (Uplink NBR for Priority value 12) . . . . . . . . . . . . . . 1632
Table 1031 NBRForPri1DL (Downlink NBR for Priority value 1) . . . . . . . . . . . . . 1633
Table 1032 NBRForPri1UL (Uplink NBR for Priority value 1) . . . . . . . . . . . . . . . . 1635
Table 1033 NBRForPri2DL (Downlink NBR for Priority value 2) . . . . . . . . . . . . . 1636
Table 1034 NBRForPri2UL (Uplink NBR for Priority value 2) . . . . . . . . . . . . . . . . 1637
Table 1035 NBRForPri3DL (Downlink NBR for Priority value 3) . . . . . . . . . . . . . 1638
Table 1036 NBRForPri3UL (Uplink NBR for Priority value 3) . . . . . . . . . . . . . . . . 1639
Table 1037 NBRForPri4DL (Downlink NBR for Priority value 4) . . . . . . . . . . . . . 1640
Table 1038 NBRForPri4UL (Uplink NBR for Priority value 4) . . . . . . . . . . . . . . . . 1641
Table 1039 NBRForPri5DL (Downlink NBR for Priority value 5) . . . . . . . . . . . . . 1642
Table 1040 NBRForPri5UL (Uplink NBR for Priority value 5) . . . . . . . . . . . . . . . . 1643
Table 1041 NBRForPri6DL (Downlink NBR for Priority value 6) . . . . . . . . . . . . . 1644
Table 1042 NBRForPri6UL (Uplink NBR for Priority value 6) . . . . . . . . . . . . . . . . 1645
Table 1043 NBRForPri7DL (Downlink NBR for Priority value 7) . . . . . . . . . . . . . 1646
Table 1044 NBRForPri7UL (Uplink NBR for Priority value 7) . . . . . . . . . . . . . . . . 1647
Table 1045 NBRForPri8DL (Downlink NBR for Priority value 8) . . . . . . . . . . . . . 1648
Table 1046 NBRForPri8UL (Uplink NBR for Priority value 8) . . . . . . . . . . . . . . . . 1649
Table 1047 NBRForPri9DL (Downlink NBR for Priority value 9) . . . . . . . . . . . . . 1650
Table 1048 NBRForPri9UL (Uplink NBR for Priority value 9) . . . . . . . . . . . . . . . . 1651
Table 1049 HSPDSCHAdjustPeriod (HS-PDSCH code adjustment period) . . . . 1652
Table 1050 HappyBitDelayConditionEDCH (Happy bit delay condition for E-DCH) . . .
1653
Table 1051 HsdschGuardTimerHO (HS-DSCH guard time after switching to DCH due
to HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1654
Table 1052 InacUserNbrXXXOverNRT (Inactive users number in XXX over NRT) . . .
1655
Table 1053 InacUsersOverloadFact (Inactive users overload preventive factor) . 1656
Table 1054 InitialSPINRT (Initial SPI for PS NRT RAB) . . . . . . . . . . . . . . . . . . . . 1658
Table 1055 MACdflowthroughputRelThr (Low throughput threshold of the MAC-d flow)
1660
Table 1056 MACdflowthroughputTimetoTrigger (Low throughput time to trigger of the
MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1661
Table 1057 MACdflowtputStrTtT (Low throughput time to trigger of streaming MAC-d
126
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1662
Table 1058 MACdflowutilStrTtT (Low util time to trigger of MAC-d flow for streaming)
1663
Table 1059 MEHCQIFeedbackCycle (Temporary CQI feedback cycle for the Mass
Event Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1665
Table 1060 MEHHSUPAUserIncr (HSUPA user increment for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1666
Table 1061 MaxBitRateNRTMACDFlow (Maximum bit rate of NRT MAC-d flow) 1668
Table 1062 MaxCSDelayRNCETTI10 (Max buffer time of the HS CS voice in RNC ETTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1670
Table 1063 MaxCSDelayRNCETTI2 (Max buffer time of the HS CS voice in RNC E-TTI
2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1672
Table 1064 MaxCSDelayUE (Max buffer time of the HS CS voice in UE) . . . . . . 1674
Table 1065 MaxEHARQReTxCSAMR10 (E-DCH max number of retransmissions CS
voice E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1675
Table 1066 MaxEHARQReTxCSAMR2 (E-DCH max number of retransmissions CS
voice E-TTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1676
Table 1067 MaxEHARQReTxPSconv10 (E-DCH max number of retransmissions PS
conv E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1677
Table 1068 MaxEHARQReTxPSconv2 (E-DCH max number of retransmissions PS
conv E-TTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1678
Table 1069 MaxReWaitTime (Maximum Reordering Wait Time for MAC-es) . . . 1679
Table 1070 MaxReWaitTime2msTTI (Maximum Reordering Wait Time for Mac-es EDCH 2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1680
Table 1071 MaxReWaitTime2msTTI16 (Maximum reordering wait time parameter for
MAC-es E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1681
Table 1072 MaxReWaitTimeRT (Maximum MAC-es Reordering Wait time for RT user)
1682
Table 1073 MaxSetOfEDPDCHCSAMR10 (Maximum Set of E-DPDCHs for CS voice
E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1683
Table 1074 MaxSetOfEDPDCHCSAMR2 (Maximum Set of E-DPDCHs for CS voice ETTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1684
Table 1075 NRTRBBRWithEDCHStr (NRT RB user bit rate with E-DCH streaming) .
1685
Table 1076 PTTRLCPDUSizeHSDSCH (RLC PDU size for PTT mapped to HSDSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1687
Table 1077 PeriodicityForSI (Periodicity for scheduling info) . . . . . . . . . . . . . . . 1688
Table 1078 PowerOffsetEHARQPSConv (HARQ power offset for E-DCH MAC-d flow
of PS conv) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1689
Table 1079 PowerOffsetEHARQVoice (HARQ power offset for E-DCH MAC-d flow of
CS voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1690
Table 1080 PowerOffsetForSI (Power Offset for Scheduling Info) . . . . . . . . . . . 1691
Table 1081 RNHSPAChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . 1692
Table 1082 RNHSPAId (RNHSPA Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1693
Table 1083 SmartHSPATimeToTrigger (Time-to-trigger for Smartphone throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1694
Table 1084 SmartHSPATputAveWin (Window size for Smartphone throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1695
Table 1085 T1HSCSVoice (HSDPA re-ordering release timer T1 for the CS voice) . .
1696
DN00211177
Issue 12B
Id:0900d805809d7397
127
WCDMA Radio Network Configuration Parameters
Table 1086 T1HSFACH (HSDPA re-ordering release timer T1 for xCCH on HS-FACH)
1698
Table 1087 T1PTT (HSDPA re-ordering rel timer T1 for the PTT) . . . . . . . . . . . . 1699
Table 1088 TGPLAMRHSDPAInterFreq (TGPL for AMR and HSDPA and IF
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1701
Table 1089 TGPLHSDPAInterFreq (TGPL for HSDPA and IF measurement) . . . 1702
Table 1090 ThresholdMaxEDPDCHSR (Threshold to define maximum E-DPDCH SR)
1703
Table 1091 ThresholdMaxEDPDCHSR1920kbps (Threshold to define maximum EDPDCH SR 1920 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1704
Table 1092 ThresholdMaxEDPDCHSR3840kbps (Threshold to define maximum EDPDCH SR 3840 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1706
Table 1093 ThresholdMaxEDPDCHSR960kbps (Threshold to define maximum EDPDCH SR 960 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1707
Table 1094 UPResAllocInCellDCHWait (Retry time for u-plane resource allocation in
Cell_DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1708
Table 1095 VCPHSDPAPrevDuration (Duration of HSDPA prevention for Voice Call
Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1710
Table 1096 VCPHSDPAUserIncr (HSDPA user increment for the Voice Call Priority)
1711
Table 1097 WeightDCH (Weight of NRT DCH UE) . . . . . . . . . . . . . . . . . . . . . . . 1713
Table 1098 WeightDCHBG (Weight of NRT DCH UE BG RAB) . . . . . . . . . . . . . 1714
Table 1099 WeightDCHTHP1 (Weight of NRT DCH UE THP1 RAB) . . . . . . . . . 1715
Table 1100 WeightDCHTHP2 (Weight of NRT DCH UE THP2 RAB) . . . . . . . . . 1716
Table 1101 WeightDCHTHP3 (Weight of NRT DCH UE THP3 RAB) . . . . . . . . . 1717
Table 1102 WeightHSPA (Weight of HSPA UE) . . . . . . . . . . . . . . . . . . . . . . . . . . 1718
Table 1103 WeightHSPABG (Weight of HSPA UE BG RAB) . . . . . . . . . . . . . . . . 1720
Table 1104 WeightHSPATHP1 (Weight of HSPA UE THP1 RAB) . . . . . . . . . . . . 1721
Table 1105 WeightHSPATHP2 (Weight of HSPA UE THP2 RAB) . . . . . . . . . . . . 1722
Table 1106 WeightHSPATHP3 (Weight of HSPA UE THP3 RAB) . . . . . . . . . . . . 1723
Table 1107 AnchorFmciIdentifier (Anchor FMCI Identifier) . . . . . . . . . . . . . . . . . . 1725
Table 1108 AnchorFmcsIdentifier (Anchor FMCS Identifier) . . . . . . . . . . . . . . . . 1726
Table 1109 AnchorHopiIdentifier (Anchor HOPI Identifier) . . . . . . . . . . . . . . . . . . 1726
Table 1110 AnchorHopsIdentifier (Anchor HOPS Identifier) . . . . . . . . . . . . . . . . . 1727
Table 1111 CellReselectionObservingTime (Cell Reselection Observing Time) . 1728
Table 1112 DRRCForHSDPALayerServices (Services for DRRC connection setup for
HSDPA layer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1730
Table 1113 DefaultAuthorisedNetworkId (Identifier of the Default Authorised Network)
1731
Table 1114 DirectedRRCForHSDPALayerEnhanc (DRRC connection setup for HSDPA layer enhancements) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1732
Table 1115 DisablePowerInHSDPALayeringDecision (Disable power in decision making for HSDPA layering) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1734
Table 1116 EcnoDifferenceThreshold (CPICH EcNo Difference Threshold) . . . . 1736
Table 1117 EnableULQualDetRep (Quality deterioration report from UL OLPC
controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1737
Table 1118 FastDormOverCpcPri (Fast Dormancy and CPC priority) . . . . . . . . . 1738
Table 1119 FastUECancel (Fast UE Cancellation) . . . . . . . . . . . . . . . . . . . . . . . . 1739
Table 1120 FastUEPeriod (Fast UE evaluation period) . . . . . . . . . . . . . . . . . . . . 1740
128
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1121 FastUEThreshold (Fast UE Threshold) . . . . . . . . . . . . . . . . . . . . . . . 1741
Table 1122 GANetwARFCN (GAN ARFCN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1742
Table 1123 GANetwBCC (GAN BCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1743
Table 1124 GANetwNCC (GAN NCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1744
Table 1125 GapPositionSingleFrame (Gap position single frame) . . . . . . . . . . . 1745
Table 1126 GsmHandoverAMR (Handover of AMR Service to GSM) . . . . . . . . . 1746
Table 1127 GsmHandoverCS (Handover of CS Service to GSM) . . . . . . . . . . . . 1748
Table 1128 GsmHandoverNrtPS (Handover of NRT PS Service to GSM) . . . . . 1749
Table 1129 GsmHandoverRtPS (Handover of RT PS Service to GSM) . . . . . . . 1751
Table 1130 HSCAHORabCombSupport (RAB Combinations Supported by HSCAHO)
1752
Table 1131 HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1753
Table 1132 HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1755
Table 1133 HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1756
Table 1134 HSDPALayerLoadShareThreshold (HSDPA layers load sharing
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1758
Table 1135 HSDPASIRErrorAveWindow (Averaging window of the SIRerror
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1759
Table 1136 HSDPASIRErrorFilterCoefficient (Higher layer filtering coefficient for HSDPA SIRerror) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1760
Table 1137 HSDPASIRErrorReportPeriod (Reporting period of the SIRerror
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1762
Table 1138 HSDPASIRErrorServCell (SIRerror threshold for the serving HS-DSCH
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1763
Table 1139 HSDPASIRErrorTargetCell (SIRerror threshold for the target cell) . 1764
Table 1140 HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1765
Table 1141 HSPADRNCEcNoOffset (DRNC Ec/No offset for HSPA Inter-RNC Cell
Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1767
Table 1142 HSPADRNCSIRErrorOffset (SIR error offset for HSPA Inter-RNC Cell
Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1768
Table 1143 IBTSRabCombSupport (RAB Combinations Supported by FD-BTS) 1770
Table 1144 LHOMinNrtDchAllocTime (Load handover minimum NRT DCH allocation
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1771
Table 1145 LowerRxTxTimeDiff (Lower Rx-Tx Time Difference Threshold) . . . . 1772
Table 1146 MBLBGuardTimer (MBLB Guard Timer) . . . . . . . . . . . . . . . . . . . . . . 1773
Table 1147 MaxCellReselections (Max cell reselections) . . . . . . . . . . . . . . . . . . 1774
Table 1148 MaxNumISHOClPerAS (Max Number of ISHO Cancellations Per Active
Set for a U) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1776
Table 1149 MultipleBSICIdent (Multiple BSIC Identification) . . . . . . . . . . . . . . . . 1777
Table 1150 NCHOFilterCoeffComLoadMeasDRNCCell (NCHO filter coefficient common load meas DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1778
Table 1151 NCHOHystComLoadMeasDRNCCell (NCHO hysteresis common load
measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1780
Table 1152 NCHOThrComLoadMeasDRNCCell (NCHO threshold common load measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1781
Table 1153 PreferBandForLayering (Preferred Band for Layering) . . . . . . . . . . . 1782
DN00211177
Issue 12B
Id:0900d805809d7397
129
WCDMA Radio Network Configuration Parameters
Table 1154 RANAPCauseLoadHO (RANAP cause to indicate load handover) . . 1783
Table 1155 RANAPCause1LoadHO (RANAP cause 1 to indicate load handover) . . .
1784
Table 1156 RANAPCause2LoadHO (RANAP cause 2 to indicate load handover) . . .
1785
Table 1157 RANAPCause3LoadHO (RANAP cause 3 to indicate load handover) . . .
1786
Table 1158 RANAPCauseServHO (RANAP cause to indicate service handover) 1787
Table 1159 RANAPCause1ServHO (RANAP cause 1 to indicate service handover) .
1788
Table 1160 RANAPCause2ServHO (RANAP cause 2 to indicate service handover) .
1789
Table 1161 RANAPCause3ServHO (RANAP cause 3 to indicate service handover) .
1790
Table 1162 RNMOBIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 1791
Table 1163 RNMOBIId (RNMOBI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1793
Table 1164 SLHOHandlingOfCellLoadMeasNotAct (SLHO handling of cell load measurement is not active) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1794
Table 1165 SLHOProfileBackgroundPSNRTData (Service profile for background PS
NRT data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1795
Table 1166 SLHOProfileConvCSSpeech (Service profile for conversational CS speech
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1797
Table 1167 SLHOProfileConvCSTData (Service profile for conversational CS T data in
SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1799
Table 1168 SLHOProfileConvPSRTData (Service profile for conversational PS RT
data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1801
Table 1169 SLHOProfileConvPSSpeech (Service profile for conversational PS speech
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1803
Table 1170 SLHOProfileInteractivePSNRTData (Service profile for interactive PS NRT
data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1805
Table 1171 SLHOProfileStreamCSNTData (Service profile for streaming CS NT data
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1807
Table 1172 SLHOProfileStreamPSRTData (Service profile for streaming PS RT data in
SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1809
Table 1173 SLHOUseBackgroundPSNRTData (Use of SLHO for background PS NRT
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1811
Table 1174 SLHOUseConvCSSpeech (Use of SLHO for conversational CS speech) .
1813
Table 1175 SLHOUseConvCSTData (Use of SLHO for conversational CS transparent
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1815
Table 1176 SLHOUseConvPSRTData (Use of SLHO for conversational PS RT data)
1817
Table 1177 SLHOUseConvPSSpeech (Use of SLHO for conversational PS speech) .
1819
Table 1178 SLHOUseInteractivePSNRTData (Use of SLHO for interactive PS NRT
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1821
Table 1179 SLHOUseStreamCSNTData (Use of SLHO for streaming CS non-transparent data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1824
Table 1180 SLHOUseStreamPSRTData (Use of SLHO for streaming PS RT data) . .
1825
130
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1181 ServBtwnHSDPALayers (Services between HSDPA layers) . . . . . . 1827
Table 1182 ServicesToHSDPALayer (Services to HSDPA layer in state transition) . .
1828
Table 1183 SmartLTELayeringPrevT (Timer for Smart LTE Layering Prevention) . .
1830
Table 1184 SmartLTELayeringServ (Smart LTE Layering service control) . . . . . 1831
Table 1185 TGPLdoubleframeNRTPSgsm (Transmision gap pattern length in case of
double frame: NRT PS service and GSM measurement) . . . . . . . . . 1832
Table 1186 TGPLdoubleframeNRTPSinterFreq (Transmision gap pattern length in
case of double frame: NRT PS service and IF measurement) . . . . . 1833
Table 1187 TGPLsingleframeAMRgsm (Transmision gap pattern length in case of single frame: AMR service and GSM measurement) . . . . . . . . . . . . . . 1834
Table 1188 TGPLsingleframeAMRinterFreq (Transmision gap pattern length in case of
single frame: AMR service and IF measurement) . . . . . . . . . . . . . . . 1835
Table 1189 TGPLsingleframeCSgsm (Transmision gap pattern length in case of single
frame: CS service and GSM measurement) . . . . . . . . . . . . . . . . . . . 1836
Table 1190 TGPLsingleframeCSinterFreq (Transmision gap pattern length in case of
single frame: CS service and IF measurement) . . . . . . . . . . . . . . . . 1837
Table 1191 TGPLsingleframeNRTPSgsm (Transmision gap pattern length in case of
single frame: NRT PS service and GSM measurement) . . . . . . . . . 1838
Table 1192 TGPLsingleframeNRTPSinterFreq (Transmision gap pattern length in case
of single frame: NRT PS service and IF measurement) . . . . . . . . . . 1839
Table 1193 TGPLsingleframeRTPSgsm (Transmision gap pattern length in case of
single frame: RT PS service and GSM measurement) . . . . . . . . . . . 1841
Table 1194 TGPLsingleframeRTPSinterFreq (Transmision gap pattern length in case
of single frame: RT PS service and IF measurement) . . . . . . . . . . . 1842
Table 1195 TRelocOverall (T RelocOverall) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1843
Table 1196 TRelocPrep (T RelocPrep) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1844
Table 1197 UEQualityRepInterv (UE Quality Measurement Reporting Interval) . 1845
Table 1198 UETxPowerMaxRef (Maximum Reference UE transmission power) 1846
Table 1199 ULQualDetRepThreshold (UL quality deterioration reporting threshold) .
1847
Table 1200 UpperRxTxTimeDiff (Upper Rx-Tx Time Difference Threshold) . . . . 1848
Table 1201 ActivationTimeOffset (Offset for activation time) . . . . . . . . . . . . . . . . 1850
Table 1202 CellDCHtestTmr (Test timer for inactivity supervision in Cell_DCH state)
1851
Table 1203 CrQueuingTimeDL (Maximum downlink capacity request queuing time) .
1852
Table 1204 CrQueuingTimeUL (Maximum uplink capacity request queuing time) 1854
Table 1205 DCHUtilBelowDowngradeThr (Threshold below the downgrade bit rate) .
1855
Table 1206 DCHUtilHighAveWin (Window size for the high throughput measurement)
1856
Table 1207 DCHUtilHighBelowNRTDataRateThr (Threshold below the NRT DCH data
rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1858
Table 1208 DCHUtilHighTimeToTrigger (Time to trigger for the high throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1860
Table 1209 DCHUtilLowerAveWinBitRate (Window size for the lower throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1861
Table 1210 DCHUtilLowerAveWin128 (Lower measurement window size for NRT DCH
DN00211177
Issue 12B
Id:0900d805809d7397
131
WCDMA Radio Network Configuration Parameters
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1863
Table 1211 DCHUtilLowerAveWin256 (Lower measurement window size for NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1865
Table 1212 DCHUtilLowerAveWin32 (Lower measurement window size for NRT DCH
of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1867
Table 1213 DCHUtilLowerAveWin384 (Lower measurement window size for NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1869
Table 1214 DCHUtilLowerAveWin64 (Lower measurement window size for NRT DCH
of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1871
Table 1215 DCHUtilLowerDowngradeThrBitRate (Lower downgrade threshold) . 1873
Table 1216 DCHUtilLowerDowngradeThr128 (Lower downgrade threshold for the NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1875
Table 1217 DCHUtilLowerDowngradeThr256 (Lower downgrade threshold for the NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1877
Table 1218 DCHUtilLowerDowngradeThr32 (Lower downgrade threshold for the NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1878
Table 1219 DCHUtilLowerDowngradeThr384 (Lower downgrade threshold for the NRT
DCH of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1879
Table 1220 DCHUtilLowerDowngradeThr64 (Lower downgrade threshold for the NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1880
Table 1221 DCHUtilLowerTimeToTriggerBitRate (Time to trigger for the lower throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1882
Table 1222 DCHUtilLowerTimeToTrigger128 (Lower time to trigger for the NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1884
Table 1223 DCHUtilLowerTimeToTrigger256 (Lower time to trigger for the NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1885
Table 1224 DCHUtilLowerTimeToTrigger32 (Lower time to trigger for the NRT DCH of
32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1886
Table 1225 DCHUtilLowerTimeToTrigger384 (Lower time to trigger for the NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1887
Table 1226 DCHUtilLowerTimeToTrigger64 (Lower time to trigger for the NRT DCH of
64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1888
Table 1227 DCHUtilMeasGuardTime (Guard time for throughput measurement) 1889
Table 1228 DCHUtilUpperAveWinBitRate (Window size for the upper throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1890
Table 1229 DCHUtilUpperAveWin128 (Upper measurement window size for NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1892
Table 1230 DCHUtilUpperAveWin256 (Upper measurement window size for NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1894
Table 1231 DCHUtilUpperAveWin32 (Upper measurement window size for NRT DCH
of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1896
Table 1232 DCHUtilUpperAveWin384 (Upper measurement window size for NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1898
Table 1233 DCHUtilUpperAveWin64 (Upper measurement window size for NRT DCH
of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900
Table 1234 DCHUtilUpperDowngradeThrBitRate (Upper downgrade threshold) . 1902
Table 1235 DCHUtilUpperDowngradeThr128 (Upper downgrade threshold for the NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1904
Table 1236 DCHUtilUpperDowngradeThr256 (Upper downgrade threshold for the NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1906
132
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1237 DCHUtilUpperDowngradeThr32 (Upper downgrade threshold for the NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1907
Table 1238 DCHUtilUpperDowngradeThr384 (Upper downgrade threshold for the NRT
DCH of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1908
Table 1239 DCHUtilUpperDowngradeThr64 (Upper downgrade threshold for the NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1909
Table 1240 DCHUtilUpperTimeToTriggerBitRate (Time to trigger for the upper
throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1910
Table 1241 DCHUtilUpperTimeToTrigger128 (Upper time to trigger for the NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1913
Table 1242 DCHUtilUpperTimeToTrigger256 (Upper time to trigger for the NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1914
Table 1243 DCHUtilUpperTimeToTrigger32 (Upper time to trigger for the NRT DCH of
32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1915
Table 1244 DCHUtilUpperTimeToTrigger384 (Upper time to trigger for the NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1916
Table 1245 DCHUtilUpperTimeToTrigger64 (Upper time to trigger for the NRT DCH of
64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1917
Table 1246 DLOptimisationProhibitTime (Dynamic Link Optimisation prohibit time) . .
1918
Table 1247 DLOptimisationPwrOffset (Power offset for dynamic link optimisation) . .
1919
Table 1248 FactorMinPBSinterval (Factor to determine minimum PBS interval) 1920
Table 1249 HSFACHDiscardTimerDTCH (Discard Timer for DTCH data on HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1922
Table 1250 HSFACHRestTimerDTCH (MAC-ehs Reset Timer for DTCH data on HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1923
Table 1251 ICRDowngradeDelayTimer (ICR Downgrade Delay Timer) . . . . . . . 1924
Table 1252 InactDetForStreamingRB (Inactivation detection for streaming radio
bearer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1925
Table 1253 IurPriority (Priority handling over Iur-interface) . . . . . . . . . . . . . . . . . 1926
Table 1254 MEHTVMPendingTime (Temporary TVM pending time for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1928
Table 1255 PTTDormancyTimer (PTT dormancy timer) . . . . . . . . . . . . . . . . . . . 1929
Table 1256 QoSPriorityMapping (QoS Priority Mapping) . . . . . . . . . . . . . . . . . . 1930
Table 1257 PriForBackARP1 (Priority for Background TC with ARP 1) . . . . . . . 1933
Table 1258 PriForBackARP2 (Priority for Background TC with ARP 2) . . . . . . . 1935
Table 1259 PriForBackARP3 (Priority for Background TC with ARP 3) . . . . . . . 1936
Table 1260 PriForConvOnHSPA (Priority for conversational on HSPA) . . . . . . . 1937
Table 1261 PriForHSFACHDTCH (Priority for PS data over HSPA on CELL_FACH
state.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1938
Table 1262 PriForIntSignaling (Priority for Interactive TC marked for signaling use) .
1939
Table 1263 PriForIntTHP1ARP1 (Priority for Interactive TC with THP 1 and ARP 1) .
1941
Table 1264 PriForIntTHP1ARP2 (Priority for Interactive TC with THP 1 and ARP 2) .
1942
Table 1265 PriForIntTHP1ARP3 (Priority for Interactive TC with THP 1 and ARP 3) .
1944
Table 1266 PriForIntTHP2ARP1 (Priority for Interactive TC with THP 2 and ARP 1) .
DN00211177
Issue 12B
Id:0900d805809d7397
133
WCDMA Radio Network Configuration Parameters
1945
Table 1267 PriForIntTHP2ARP2 (Priority for Interactive TC with THP 2 and ARP 2) .
1946
Table 1268 PriForIntTHP2ARP3 (Priority for Interactive TC with THP 2 and ARP 3) .
1947
Table 1269 PriForIntTHP3ARP1 (Priority for Interactive TC with THP 3 and ARP 1) .
1949
Table 1270 PriForIntTHP3ARP2 (Priority for Interactive TC with THP 3 and ARP 2) .
1950
Table 1271 PriForIntTHP3ARP3 (Priority for Interactive TC with THP 3 and ARP 3) .
1951
Table 1272 PriForSRBsOnHSPA (Priority for SRBs on HSPA) . . . . . . . . . . . . . . 1952
Table 1273 PriForStreamARP1 (Priority for Streaming traffic class with ARP1) . 1953
Table 1274 PriForStreamARP2 (Priority for Streaming traffic class with ARP2) . 1955
Table 1275 PriForStreamARP3 (Priority for Streaming traffic class with ARP3) . 1956
Table 1276 RNPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 1958
Table 1277 RNPSId (RNPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1959
Table 1278 RTOverNRTPriThresholdARP1 (RT-over-NRT priority threshold for
ARP1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1960
Table 1279 RTOverNRTPriThresholdARP2 (RT-over-NRT priority threshold for
ARP2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1961
Table 1280 RTOverNRTPriThresholdARP3 (RT-over-NRT priority threshold for
ARP3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1962
Table 1281 SmartInactTimerFACH (Inactivity Timer for Smart Phones in Cell_FACH)
1964
Table 1282 SmartInactivityTimerDCH (Inactivity timer for Smartphone DCH) . . . 1965
Table 1283 ToCellFACHinTest (Test switch for Iu release in Cell_DCH state) . . 1966
Table 1284 TrafVolThresholdDLHigh (Downlink traffic volume measurement high
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1967
Table 1285 TrafVolThresholdDLHighBitRate (Traffic volume threshold for downlink
NRT DCH bit rates) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1969
Table 1286 TrafVolThresholdDLHighDCH128 (Traffic volume threshold for DL NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1971
Table 1287 TrafVolThresholdDLHighDCH16 (Traffic volume threshold for DL NRT
DCH of 16 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1973
Table 1288 TrafVolThresholdDLHighDCH256 (Traffic volume threshold for DL NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1975
Table 1289 TrafVolThresholdDLHighDCH32 (Traffic volume threshold for DL NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1977
Table 1290 TrafVolThresholdDLHighDCH64 (Traffic volume threshold for DL NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1979
Table 1291 TrafVolThresholdDLHighDCH8 (Traffic volume threshold for DL NRT DCH
of 8 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1981
Table 1292 TrafVolThresholdULHigh (Uplink traffic volume measurement high
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1983
Table 1293 TrafVolThresholdULHighBitRate (Traffic volume threshold for uplink NRT
DCH bit rates) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1985
Table 1294 TrafVolThresholdULHighDCH128 (Traffic volume threshold for UL NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1987
Table 1295 TrafVolThresholdULHighDCH16 (Traffic volume threshold for UL NRT
134
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
DCH of 16 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1989
Table 1296 TrafVolThresholdULHighDCH256 (Traffic volume threshold for UL NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1991
Table 1297 TrafVolThresholdULHighDCH32 (Traffic volume threshold for UL NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1993
Table 1298 TrafVolThresholdULHighDCH64 (Traffic volume threshold for UL NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1995
Table 1299 TrafVolThresholdULHighDCH8 (Traffic volume threshold for UL NRT DCH
of 8 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1997
Table 1300 TrafVolTimeToTriggerDL (Downlink traffic volume measurement time to
trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1999
Table 1301 TrafVolTimeToTriggerUL (Uplink traffic volume measurement time to
trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000
Table 1302 ULLoadStateTTT (UL loaded state time to trigger) . . . . . . . . . . . . . . 2002
Table 1303 AMRLCBufMaxOverbook2NRT (AM RLC buffer max total overbooking for
2 PS RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2004
Table 1304 AMRLCBufMaxOverbook3NRT (AM RLC buffer max overbooking for more
than 2 PS RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2005
Table 1305 AMRLCHSFACHPS (AM RLC configuration for PS NRT with HS-FACH)
2006
Table 1306 AMRLCHSFACHPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2007
Table 1307 AMRLCHSFACHPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2008
Table 1308 AMRLCHSFACHPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2010
Table 1309 AMRLCHSFACHPSPeriodMax (AM RLC status period max for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2011
Table 1310 AMRLCHSFACHPSPeriodMin (AM RLC status period min for PS NRT with
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2012
Table 1311 AMRLCHSFACHPSPollPDU (AM RLC period Poll_PDU for PS NRT with
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2013
Table 1312 AMRLCHSFACHPSPollSDU (AM RLC period Poll_SDU for PS NRT with
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2015
Table 1313 AMRLCHSFACHPSPollWin (AM RLC period Poll_Window for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2016
Table 1314 AMRLCHSFACHPSTriggers (AM RLC status report triggers for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2017
Table 1315 AMRLCRespHSFACHandRACH (AM RLC round trip time with HSDSCH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2019
Table 1316 HSFACHAMRLCRespHSRACH (AM RLC round trip time with HSDSCH/HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2020
Table 1317 AMRLCHSRACHPS (AM RLC configuration for PS NRT with HS-RACH)
2022
Table 1318 AMRLCHSRACHPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2023
Table 1319 AMRLCHSRACHPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2024
Table 1320 AMRLCHSRACHPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2025
Table 1321 AMRLCHSRACHPSPeriodMax (AM RLC status period max for PS NRT
DN00211177
Issue 12B
Id:0900d805809d7397
135
WCDMA Radio Network Configuration Parameters
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2026
Table 1322 AMRLCHSRACHPSPeriodMin (AM RLC status period min for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2028
Table 1323 AMRLCHSRACHPSPollPDU (AM RLC period Poll_PDU for PS NRT with
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2029
Table 1324 AMRLCHSRACHPSPollSDU (AM RLC period Poll_SDU for PS NRT with
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2030
Table 1325 AMRLCHSRACHPSPollWin (AM RLC period Poll_Window for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2031
Table 1326 AMRLCHSRACHPSTriggers (AM RLC status report triggers for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2033
Table 1327 HSRACHAMRLCRespHSFACH (AM RLC round trip time with HS-RACH/HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2035
Table 1328 AMRLCMaximumBufferUE (AM RLC maximum buffer allocation for UE) .
2036
Table 1329 AMRLCMaximumBufferUE100 (AM RLC maximum buffer allocation for UE
capability 100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2038
Table 1330 AMRLCMaximumBufferUE1150 (AM RLC maximum buffer allocation for
UE capability 1150) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2039
Table 1331 AMRLCMaximumBufferUE1250 (AM RLC maximum buffer allocation for
UE capability 1250) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2040
Table 1332 AMRLCMaximumBufferUE150 (AM RLC maximum buffer allocation for UE
capability 150) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2041
Table 1333 AMRLCMaximumBufferUE1k (AM RLC maximum buffer allocation for UE
capability 1000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2042
Table 1334 AMRLCMaximumBufferUE200 (AM RLC maximum buffer allocation for UE
capability 200) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2043
Table 1335 AMRLCMaximumBufferUE300 (AM RLC maximum buffer allocation for UE
capability 300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2044
Table 1336 AMRLCMaximumBufferUE50 (AM RLC maximum buffer allocation for UE
capability 50) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2045
Table 1337 AMRLCMaximumBufferUE500 (AM RLC maximum buffer allocation for UE
capability 500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2046
Table 1338 AMRLCMaximumBufferUE750 (AM RLC maximum buffer allocation for UE
capability 750) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2047
Table 1339 AMRLCmaximumBufferUE400 (AM RLC maximum buffer allocation for UE
capability 400) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2049
Table 1340 AMRLCOnDCHOfNRTPS (AM RLC configuration for PS NRT with DCH)
2050
Table 1341 AMRLCOnDCHOfNRTPSCount (AM RLC status reports count for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2051
Table 1342 AMRLCOnDCHOfNRTPSFilterReTX (AM RLC retransmission filter for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2053
Table 1343 AMRLCOnDCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2055
Table 1344 AMRLCOnDCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2056
Table 1345 AMRLCOnDCHOfNRTPSMaxRST (AM RLC MaxRST transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2058
Table 1346 AMRLCOnDCHOfNRTPSPeriodMax (AM RLC status period max for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2059
136
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1347 AMRLCOnDCHOfNRTPSPeriodMin (AM RLC status period min for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2060
Table 1348 AMRLCOnDCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2061
Table 1349 AMRLCOnDCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2063
Table 1350 AMRLCOnDCHOfNRTPSPollWindow (AM RLC period Poll_Window for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2064
Table 1351 AMRLCOnDCHOfNRTPSTriggers (AM RLC status report triggers for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2065
Table 1352 AMRLCOnDCHOfSRB136 (AM RLC configuration for SRB13.6 with DCH)
2068
Table 1353 AMRLCOnDCHOfSRB136MaxDAT (AM RLC MaxDAT transmissions for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2069
Table 1354 AMRLCOnDCHOfSRB136PeriodMax (AM RLC status period max for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2070
Table 1355 AMRLCOnDCHOfSRB136PeriodMin (AM RLC status period min for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2071
Table 1356 AMRLCOnDCHOfSRB136PollPDU (AM RLC period Poll_PDU for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2072
Table 1357 AMRLCOnDCHOfSRB136PollSDU (AM RLC period Poll_SDU for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2074
Table 1358 AMRLCOnDCHOfSRB136PollWindow (AM RLC period Poll_Window for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2075
Table 1359 AMRLCOnDCHOfSRB136Triggers (AM RLC status report triggers for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2076
Table 1360 AMRLCOnDCHOfSRB34 (AM RLC configuration for SRB3.4 with DCH)
2078
Table 1361 AMRLCOnDCHOfSRB34MaxDAT (AM RLC MaxDAT transmissions for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2079
Table 1362 AMRLCOnDCHOfSRB34PeriodMax (AM RLC status period max for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2080
Table 1363 AMRLCOnDCHOfSRB34PeriodMin (AM RLC status period min for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2082
Table 1364 AMRLCOnDCHOfSRB34PollPDU (AM RLC period Poll_PDU for SRB3.4
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2083
Table 1365 AMRLCOnDCHOfSRB34PollSDU (AM RLC period Poll_SDU for SRB3.4
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2084
Table 1366 AMRLCOnDCHOfSRB34PollWindow (AM RLC period Poll_Window for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2085
Table 1367 AMRLCOnDCHOfSRB34Triggers (AM RLC status report triggers for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2086
Table 1368 AMRLCOnDCHOfStream (AM RLC configuration for PS streaming with
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2088
Table 1369 AMRLCOnDCHOfStreamCount (AM RLC status reports count for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2089
Table 1370 AMRLCOnDCHOfStreamDiscardTime (AM RLC SDU discard time for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2091
Table 1371 AMRLCOnDCHOfStreamFilterReTX (AM RLC retransmission filter for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2092
Table 1372 AMRLCOnDCHOfStreamMaxDAT (AM RLC MaxDAT transmissions for
DN00211177
Issue 12B
Id:0900d805809d7397
137
WCDMA Radio Network Configuration Parameters
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2094
Table 1373 AMRLCOnDCHOfStreamMaxMRW (AM RLC MaxMRW transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2095
Table 1374 AMRLCOnDCHOfStreamMaxRST (AM RLC MaxRST transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2097
Table 1375 AMRLCOnDCHOfStreamPeriodMax (AM RLC status period max for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2098
Table 1376 AMRLCOnDCHOfStreamPeriodMin (AM RLC status period min for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2099
Table 1377 AMRLCOnDCHOfStreamPollPDU (AM RLC period Poll_PDU for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2100
Table 1378 AMRLCOnDCHOfStreamPollSDU (AM RLC period Poll_SDU for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2102
Table 1379 AMRLCOnDCHOfStreamPollWindow (AM RLC period Poll_Window for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2103
Table 1380 AMRLCOnDCHOfStreamTriggers (AM RLC status report triggers for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2104
Table 1381 AMRLCOnDCHSRB136OffSat (AM RLC timer offset for SRB13.6 with satellite DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2106
Table 1382 AMRLCOnEDCHOfNRTPS (AM RLC configuration for PS NRT with EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2108
Table 1383 AMRLCOnEDCHOfNRTPSCount (AM RLC status reports count for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2109
Table 1384 AMRLCOnEDCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2111
Table 1385 AMRLCOnEDCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions
for PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2112
Table 1386 AMRLCOnEDCHOfNRTPSMaxRST (AM RLC maxRST transmissions for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2113
Table 1387 AMRLCOnEDCHOfNRTPSPeriodMax (AM RLC status period max for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2114
Table 1388 AMRLCOnEDCHOfNRTPSPeriodMin (AM RLC status period min for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2116
Table 1389 AMRLCOnEDCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2117
Table 1390 AMRLCOnEDCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2118
Table 1391 AMRLCOnEDCHOfNRTPSPollWindow (AM RLC period Poll_Window for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2119
Table 1392 AMRLCOnEDCHOfNRTPSTriggers (AM RLC status report triggers for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2120
Table 1393 AMRLCOnEDCHOfStrPS (AM RLC configuration for PS streaming with EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2122
Table 1394 EDCHStrPSCount (AM RLC status reports count for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2124
Table 1395 EDCHStrPSDiscardTime (AM RLC SDU discard time for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2126
Table 1396 EDCHStrPSMaxDAT (AM RLC MaxDAT transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2127
Table 1397 EDCHStrPSMaxMRW (AM RLC MaxMRW transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2128
138
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1398 EDCHStrPSMaxRST (AM RLC maxRST transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2129
Table 1399 EDCHStrPSPeriodMax (AM RLC status period max for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2130
Table 1400 EDCHStrPSPeriodMin (AM RLC status period min for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2132
Table 1401 EDCHStrPSPollPDU (AM RLC period Poll_PDU for PS streaming E-DCH)
2133
Table 1402 EDCHStrPSPollSDU (AM RLC period Poll_SDU for PS streaming E-DCH)
2134
Table 1403 EDCHStrPSPollWindow (AM RLC period Poll_Window for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2135
Table 1404 EDCHStrPSTriggers (AM RLC status report triggers for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2136
Table 1405 AMRLCOnFACHOfPS (AM RLC configuration for PS NRT with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2138
Table 1406 AMRLCOnFACHOfPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2140
Table 1407 AMRLCOnFACHOfPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2141
Table 1408 AMRLCOnFACHOfPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with FACH/RAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2142
Table 1409 AMRLCOnFACHOfPSPeriodMax (AM RLC status period max for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2143
Table 1410 AMRLCOnFACHOfPSPeriodMin (AM RLC status period min for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2144
Table 1411 AMRLCOnFACHOfPSPollPDU (AM RLC period Poll_PDU for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2145
Table 1412 AMRLCOnFACHOfPSPollSDU (AM RLC period Poll_SDU for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2147
Table 1413 AMRLCOnFACHOfPSPollWindow (AM RLC period Poll_Window for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2148
Table 1414 AMRLCOnFACHOfPSTriggers (AM RLC status report triggers for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2149
Table 1415 AMRLCOnFACHOfSRB (AM RLC configuration for SRB with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2151
Table 1416 AMRLCOnFACHOfSRBMaxDAT (AM RLC MaxDAT transmissions for
SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2152
Table 1417 AMRLCOnFACHOfSRBPeriodMax (AM RLC status period max for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2154
Table 1418 AMRLCOnFACHOfSRBPeriodMin (AM RLC status period min for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2155
Table 1419 AMRLCOnFACHOfSRBPollPDU (AM RLC period Poll_PDU for SRB with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2156
Table 1420 AMRLCOnFACHOfSRBPollSDU (AM RLC period Poll_SDU for SRB with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2158
Table 1421 AMRLCOnFACHOfSRBPollWindow (AM RLC period Poll_Window for
SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2159
Table 1422 AMRLCOnFACHOfSRBTriggers (AM RLC status report triggers for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2160
Table 1423 AMRLCOnHSDSCHOfNRTPS (AM RLC configuration for PS NRT with
DN00211177
Issue 12B
Id:0900d805809d7397
139
WCDMA Radio Network Configuration Parameters
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2162
Table 1424 AMRLCOnHSDSCHOfNRTPSCount (AM RLC status reports count for PS
NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2163
Table 1425 AMRLCOnHSDSCHOfNRTPSFilterReTX (AM RLC retransmission filter
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2165
Table 1426 AMRLCOnHSDSCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2167
Table 1427 AMRLCOnHSDSCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2168
Table 1428 AMRLCOnHSDSCHOfNRTPSMaxRST (AM RLC maxRST transmissions
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2169
Table 1429 AMRLCOnHSDSCHOfNRTPSPeriodMax (AM RLC status period max for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2170
Table 1430 AMRLCOnHSDSCHOfNRTPSPeriodMin (AM RLC status period min for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2172
Table 1431 AMRLCOnHSDSCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS
NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2173
Table 1432 AMRLCOnHSDSCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS
NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2174
Table 1433 AMRLCOnHSDSCHOfNRTPSPollWindow (AM RLC period Poll_Window
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2175
Table 1434 AMRLCOnHSDSCHOfNRTPSTriggers (AM RLC status report triggers for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2176
Table 1435 AMRLCOnHSDSCHOfStrPS (AM RLC configuration for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2179
Table 1436 HSDSCHStrDiscardTime (AM RLC SDU discard time for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2180
Table 1437 HSDSCHStrPSCount (AM RLC status reports count for PS stream with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2182
Table 1438 HSDSCHStrPSFilterReTX (AM RLC retransmission filter for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2183
Table 1439 HSDSCHStrPSMaxDAT (AM RLC MaxDAT transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2185
Table 1440 HSDSCHStrPSMaxMRW (AM RLC MaxMRW transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2186
Table 1441 HSDSCHStrPSMaxRST (AM RLC maxRST transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2187
Table 1442 HSDSCHStrPSPeriodMax (AM RLC status period max for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2188
Table 1443 HSDSCHStrPSPeriodMin (AM RLC status period min for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2190
Table 1444 HSDSCHStrPSPollPDU (AM RLC period Poll_PDU for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2191
Table 1445 HSDSCHStrPSPollSDU (AM RLC period Poll_SDU for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2192
Table 1446 HSDSCHStrPSPollWindow (AM RLC period Poll_Window for PS streaming with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2193
Table 1447 HSDSCHStrPSTriggers (AM RLC status report triggers for PS str with HSDSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2194
Table 1448 AMRLCPeriodMaxHSSRB (AM RLC status period max for SRBs with HSRACH/HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2197
140
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1449 AMRLCRTTPollPDUSatellite (AM RLC period Poll_PDU with satellite Iub)
2198
Table 1450 AMRLCRelatTXWindow (AM RLC relative transmission window sizes) . .
2199
Table 1451 AMRLCRelatTXWindowRate1 (AM RLC relative Tx window size defining
data rate 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2200
Table 1452 AMRLCRelatTXWindowRate1Size (AM RLC relative Tx window size assigned to data rate 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2201
Table 1453 AMRLCRelatTXWindowRate2 (AM RLC relative Tx window size defining
data rate 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2203
Table 1454 AMRLCRelatTXWindowRate2Size (AM RLC relative Tx window size assigned to data rate 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2204
Table 1455 AMRLCRelatTXWindowRate3 (AM RLC relative Tx window size defining
data rate 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2205
Table 1456 AMRLCRelatTXWindowRate3Size (AM RLC relative Tx window size assigned to data rate 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2206
Table 1457 AMRLCRelatTXWindowRate4 (AM RLC relative Tx window size defining
data rate 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2207
Table 1458 AMRLCRelatTXWindowRate4Size (AM RLC relative Tx window size assigned to data rate 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2208
Table 1459 AMRLCRelatTXWindowRate5 (AM RLC relative Tx window size defining
data rate 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2209
Table 1460 AMRLCRelatTXWindowRate5Size (AM RLC relative Tx window size assigned to data rate 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2210
Table 1461 AMRLCRelatTXWindowRate6 (AM RLC relative Tx window size defining
data rate 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2211
Table 1462 AMRLCRelatTXWindowRate6Size (AM RLC relative Tx window size assigned to data rate 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2212
Table 1463 AMRLCRelatTXWindowRate7 (AM RLC relative Tx window size defining
data rate 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2213
Table 1464 AMRLCRelatTXWindowRate7Size (AM RLC relative Tx window size assigned to data rate 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2214
Table 1465 AMRLCRelatTXWindowRate8 (AM RLC relative Tx window size defining
data rate 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2215
Table 1466 AMRLCRelatTXWindowRate8Size (AM RLC relative Tx window size assigned to data rate 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2216
Table 1467 AMRLCRespTimeDCH (AM RLC round trip times with DCH) . . . . . 2217
Table 1468 AMRLCRespTimeDCH10 (AM RLC round trip time with DCH/DCH of TTI
10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2218
Table 1469 AMRLCRespTimeDCH20 (AM RLC round trip time with DCH/DCH of TTI
20 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2219
Table 1470 AMRLCRespTimeDCH40 (AM RLC round trip time with DCH/DCH of TTI
40 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2220
Table 1471 AMRLCRespTimeDCHRevHSDSCH (AM RLC round trip time for
DCH/HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2221
Table 1472 AMRLCRespTimeRevEDCH (AM RLC round trip time for E-DCH/DCH) .
2222
Table 1473 AMRLCRespTimeEDCH (AM RLC round trip time with E-DCH) . . . 2223
Table 1474 AMRLCRespTimeFACHAndRACH (AM RLC round trip time with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2224
Table 1475 AMRLCRespTimeHSDSCH (AM RLC round trip times with HS-DSCH) .
DN00211177
Issue 12B
Id:0900d805809d7397
141
WCDMA Radio Network Configuration Parameters
2225
Table 1476 AMRLCRespTimeHSDSCHRevDCH (AM RLC round trip time with HSDSCH/DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2226
Table 1477 AMRLCRespTimeHSDSCHRevEDCH (AM RLC round trip time with HSDSCH/E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2227
Table 1478 AMRLCRespTimeHSSRB (AM RLC round trip time for SRBs with HS-RACH/HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2228
Table 1479 AMRLCSRB3n4PeriodMax (AM RLC status period max for SRB3 and
SRB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2229
Table 1480 AMRLCSRB3n4RespTime (AM RLC round trip time for SRB3 and SRB4)
2230
Table 1481 AMRLCSRBHSPA (AM RLC configuration for SRB on HSPA) . . . . . 2232
Table 1482 AMRLCRespTimeSRBHSPA (AM RLC round trip time for SRB on HSPA)
2233
Table 1483 AMRLCSRBHSPAMaxDAT (AM RLC MaxDAT transmissions for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2234
Table 1484 AMRLCSRBHSPAPeriodMax (AM RLC status period max for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2235
Table 1485 AMRLCSRBHSPAPeriodMin (AM RLC status period min for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2236
Table 1486 AMRLCSRBHSPAPollPDU (AM RLC period Poll_PDU for SRB on HSPA)
2237
Table 1487 AMRLCSRBHSPAPollSDU (AM RLC period Poll_SDU for SRB on HSPA)
2239
Table 1488 AMRLCSRBHSPAPollWindow (AM RLC period Poll_Window for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2240
Table 1489 AMRLCSRBHSPATriggers (AM RLC status report triggers for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2241
Table 1490 AMRLCTXWindowSizeSRB (AM RLC transmission window sizes for SRBs
2, 3 and 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2243
Table 1491 AMRLCTXWindowSizeSRB2 (AM RLC transmission window size for SRB
2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2244
Table 1492 AMRLCTXWindowSizeSRB3 (AM RLC transmission window size for SRB
3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2245
Table 1493 AMRLCTXWindowSizeSRB4 (AM RLC transmission window size for SRB
4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2247
Table 1494 PDUSizeBitRateThr (Bit rate threshold for RLC PDU size 656 with HSDSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2248
Table 1495 PDUSizeCodeThreshold (Number of HS-PDSCH codes for greater RLC
PDU size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2249
Table 1496 PDUSizeSIRThr (SIR threshold for RLC PDU size 656 with HS-DSCH) . .
2251
Table 1497 RLCConfOptionFPS (RLC Conf option switch for Fast Cell_PCH
Switching) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2252
Table 1498 RNRLCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 2254
Table 1499 RNRLCId (RNRLC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2255
Table 1500 SDUdiscardModeRTPS (SDU discard mode for RT PS RAB employing
RLC AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2256
Table 1501 UMRLCEVoiceDiscardTime (UM RLC SDU discard time in UE for CS voice
over HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2257
142
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1502 UMRLCPTTDiscardTime (UM RLC SDU discard time in UE for PTT) . . .
2258
Table 1503 A2EA (AAL type 2 end point address for Iur) . . . . . . . . . . . . . . . . . . 2260
Table 1504 ActivityFactorForAMRDCHTrafficBearers (Activity factor for AMR DCH
traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2262
Table 1505 Af122AMRDL (Activity factor for 12.2 / 12.65 AMR DCH DL bearer) 2263
Table 1506 Af122AMRUL (Activity factor for 12.2 / 12.65 AMR DCH UL bearer) 2264
Table 1507 Af59AMRDL (Activity factor for 5.9 AMR DCH DL bearer) . . . . . . . . 2265
Table 1508 Af59AMRUL (Activity factor for 5.9 AMR DCH UL bearer) . . . . . . . . 2266
Table 1509 ActivityFactorForCSDCHTrafficBearers (Activity factor for CS DCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2267
Table 1510 Af144CSStreDL (Activity factor for 14.4 CS streaming DL bearer) . . 2268
Table 1511 Af144CSStreUL (Activity factor for 14.4 CS streaming UL bearer) . . 2269
Table 1512 Af576CSStreDL (Activity factor for 57.6 CS streaming DL bearer) . . 2270
Table 1513 Af576CSStreUL (Activity factor for 57.6 CS streaming UL bearer) . . 2271
Table 1514 Af64CSConDL (Activity factor for 64 CS conversational DL bearer) 2272
Table 1515 Af64CSConUL (Activity factor for 64 CS conversational UL bearer) 2273
Table 1516 ActivityFactorForDCCHTrafficBearers (Activity factor for DCCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2274
Table 1517 Af128And136DCCHDL (Activity factor for 12.8/13.6 DCCH DL bearer) . .
2275
Table 1518 Af128And136DCCHUL (Activity factor for 12.8/13.6 DCCH UL bearer) . .
2276
Table 1519 Af16And17DCCHDL (Activity factor for 1.6/1.7 DCCH DL bearer) . . 2277
Table 1520 Af16And17DCCHUL (Activity factor for 1.6/1.7 DCCH UL bearer) . . 2278
Table 1521 Af32And34DCCHDL (Activity factor for 3.2/3.4 DCCH DL bearer) . . 2279
Table 1522 Af32And34DCCHUL (Activity factor for 3.2/3.4 DCCH UL bearer) . . 2280
Table 1523 ActivityFactorForFACHRACHTrafficBearers (Activity factor for FACH and
RACH traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2281
Table 1524 AfFACHCCDL (Activity factor for FACH-C/C DL bearer) . . . . . . . . . 2282
Table 1525 AfFACHCIDL (Activity factor for FACH-C/I DL bearer) . . . . . . . . . . . 2283
Table 1526 AfFACHContUL (Activity factor for FACH control UL bearer) . . . . . . 2284
Table 1527 AfFACHSDL (Activity factor for FACH-S DL bearer) . . . . . . . . . . . . 2285
Table 1528 AfFACHUDL (Activity factor for FACH-U DL bearer) . . . . . . . . . . . . 2286
Table 1529 AfRACH208UL (Activity factor for RACH 20.8 UL bearer) . . . . . . . . 2287
Table 1530 AfRACHContDL (Activity factor for RACH control DL bearer) . . . . . 2288
Table 1531 ActivityFactorForHSPA (Activity factor for HSPA bearers) . . . . . . . . 2289
Table 1532 AfPTTDL (Activity Factor for PTT RAB in Downlink) . . . . . . . . . . . . 2290
Table 1533 AfPTTUL (Activity Factor for PTT RAB in Uplink) . . . . . . . . . . . . . . . 2291
Table 1534 AfRTHSDPA (Activity factor for RT HSDPA bearer) . . . . . . . . . . . . . 2292
Table 1535 AfRTHSUPA (Activity factor for RT HSUPA bearer) . . . . . . . . . . . . . 2293
Table 1536 AfSRBOnHSDPA (Activity factor for SRB on HSDPA bearer) . . . . . 2294
Table 1537 AfSRBOnHSUPA (Activity factor for SRB on HSUPA bearer) . . . . . 2295
Table 1538 ActivityFactorForNRTDCHTrafficBearers (Activity factor for NRT DCH traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2296
Table 1539 Af128NRTDCHDL (Activity factor for 128 NRT DCH DL bearer) . . . 2297
Table 1540 Af128NRTDCHUL (Activity factor for 128 NRT DCH UL bearer) . . . 2298
Table 1541 Af16NRTDCHDL (Activity factor for 16 NRT DCH DL bearer) . . . . . 2299
DN00211177
Issue 12B
Id:0900d805809d7397
143
WCDMA Radio Network Configuration Parameters
Table 1542 Af16NRTDCHUL (Activity factor for 16 NRT DCH UL bearer) . . . . . . 2300
Table 1543 Af256NRTDCHDL (Activity factor for 256 NRT DCH DL bearer) . . . . 2301
Table 1544 Af256NRTDCHUL (Activity factor for 256 NRT DCH UL bearer) . . . . 2302
Table 1545 Af32NRTDCHDL (Activity factor for 32 NRT DCH DL bearer) . . . . . . 2303
Table 1546 Af32NRTDCHUL (Activity factor for 32 NRT DCH UL bearer) . . . . . . 2304
Table 1547 Af384NRTDCHDL (Activity factor for 384 NRT DCH DL bearer) . . . . 2305
Table 1548 Af384NRTDCHUL (Activity factor for 384 NRT DCH UL bearer) . . . . 2306
Table 1549 Af64NRTDCHDL (Activity factor for 64 NRT DCH DL bearer) . . . . . . 2307
Table 1550 Af64NRTDCHUL (Activity factor for 64 NRT DCH UL bearer) . . . . . . 2308
Table 1551 Af8NRTDCHDL (Activity factor for 8 NRT DCH DL bearer) . . . . . . . . 2309
Table 1552 Af8NRTDCHUL (Activity factor for 8 NRT DCH UL bearer) . . . . . . . . 2310
Table 1553 ActivityFactorForPCHTrafficBearers (Activity factor for PCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2311
Table 1554 AfPCHContUL (Activity factor for PCH control UL bearer) . . . . . . . . 2312
Table 1555 AfPCHDL (Activity factor for PCH DL bearer) . . . . . . . . . . . . . . . . . . 2313
Table 1556 ActivityFactorForRTPSTrafficBearers (Activity factor for RT PS traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2314
Table 1557 Af128RTPSAMDL (Activity factor for 128 RT PS AM DL bearer) . . . 2316
Table 1558 Af128RTPSAMUL (Activity factor for 128 RT PS AM UL bearer) . . . 2317
Table 1559 Af128RTPSUMDL (Activity factor for 128 RT PS UM DL bearer) . . . 2318
Table 1560 Af128RTPSUMUL (Activity factor for 128 RT PS UM UL bearer) . . . 2319
Table 1561 Af16RTPSAMDL (Activity factor for 16 RT PS AM DL bearer) . . . . . 2320
Table 1562 Af16RTPSAMUL (Activity factor for 16 RT PS AM UL bearer) . . . . . 2321
Table 1563 Af16RTPSUMDL (Activity factor for 16 RT PS UM DL bearer) . . . . . 2322
Table 1564 Af16RTPSUMUL (Activity factor for 16 RT PS UM UL bearer) . . . . . 2323
Table 1565 Af256RTPSAMDL (Activity factor for 256 RT PS AM DL bearer) . . . 2324
Table 1566 Af256RTPSUMDL (Activity factor for 256 RT PS UM DL bearer) . . . 2325
Table 1567 Af32RTPSAMDL (Activity factor for 32 RT PS AM DL bearer) . . . . . 2326
Table 1568 Af32RTPSAMUL (Activity factor for 32 RT PS AM UL bearer) . . . . . 2327
Table 1569 Af32RTPSUMDL (Activity factor for 32 RT PS UM DL bearer) . . . . . 2328
Table 1570 Af32RTPSUMUL (Activity factor for 32 RT PS UM UL bearer) . . . . . 2329
Table 1571 Af64RTPSAMDL (Activity factor for 64 RT PS AM DL bearer) . . . . . 2330
Table 1572 Af64RTPSAMUL (Activity factor for 64 RT PS AM UL bearer) . . . . . 2331
Table 1573 Af64RTPSUMDL (Activity factor for 64 RT PS UM DL bearer) . . . . . 2332
Table 1574 Af64RTPSUMUL (Activity factor for 64 RT PS UM UL bearer) . . . . . 2333
Table 1575 Af8RTPSAMDL (Activity factor for 8 RT PS AM DL bearer) . . . . . . . 2334
Table 1576 Af8RTPSAMUL (Activity factor for 8 RT PS AM UL bearer) . . . . . . . 2335
Table 1577 Af8RTPSUMDL (Activity factor for 8 RT PS UM DL bearer) . . . . . . . 2336
Table 1578 Af8RTPSUMUL (Activity factor for 8 RT PS UM UL bearer) . . . . . . . 2337
Table 1579 DSCPBTSOMToBTS (DSCP for BTS OM towards BTS) . . . . . . . . . 2338
Table 1580 DSCPBTSOMToOMS (DSCP for BTS OM towards OMS) . . . . . . . . 2338
Table 1581 DSCPForGTPSignalling (DSCP for GTP signalling) . . . . . . . . . . . . . 2339
Table 1582 EchoRequestSending (Echo Request Sending) . . . . . . . . . . . . . . . . 2340
Table 1583 HSDPAFlowControlLowThresholdDedicatedVCC (HSDPA flow control
AAL2 low threshold for dedicated VCC) . . . . . . . . . . . . . . . . . . . . . . 2342
Table 1584 HSDPAFlowControlLowThresholdSharedVCC (HSDPA flow control AAL2
low threshold for shared VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2343
Table 1585 HSDPAFlowControlTargetDelayDedicatedVCC (HSDPA flow control
144
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
AAL2 target delay for dedicated VCC) . . . . . . . . . . . . . . . . . . . . . . . 2344
Table 1586 HSDPAFlowControlTargetDelaySharedVCC (HSDPA flow control AAL2
target delay for shared VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2345
Table 1587 IPStackErrorTimer (IP Stack Error timer) . . . . . . . . . . . . . . . . . . . . . 2346
Table 1588 IuDATree (Iu-CS Digit analysis tree) . . . . . . . . . . . . . . . . . . . . . . . . . 2347
Table 1589 IubDATree (Iub Digit analysis tree) . . . . . . . . . . . . . . . . . . . . . . . . . . 2348
Table 1590 IurDATree (Iur Digit analysis tree) . . . . . . . . . . . . . . . . . . . . . . . . . . 2348
Table 1591 N3Requests (N3-REQUESTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2349
Table 1592 NRTDCHFlowControlTargetDelay (NRTDCH Flow Control Target Delay)
2350
Table 1593 RNTRMChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 2351
Table 1594 RNTRMId (RNTRM Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2353
Table 1595 RespSyncCounterIP (Response synchronization counter for DL synch
frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2354
Table 1596 RespSyncModEnableIP (IP Iub DCH Sync Modifiable) . . . . . . . . . . 2355
Table 1597 RespSyncTimerIP (IP Response synchronization timer for DL synch
frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2356
Table 1598 RespSyncTimerSatIP (IP Response synchronization timer with Satellite
Iub) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2357
Table 1599 T3Response (T3-RESPONSE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2358
Table 1600 THP1DelaySensitivitySwitch (THP 1 Delay Sensitivity Switch) . . . . 2359
Table 1601 THP2DelaySensitivitySwitch (THP 2 Delay Sensitivity Switch) . . . . 2360
Table 1602 THP3DelaySensitivitySwitch (THP 3 Delay Sensitivity Switch) . . . . 2361
Table 1603 ToAWEOffsetForOverbook (ToAWE Offset for overbooked NRT DCH
AAL2 connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2362
Table 1604 ToAWSOffsetForOverbook (ToAWS Offset for overbooked NRT DCH
AAL2 connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2364
Table 1605 ULCACSwitch (Enhanced UL CAC Algorithm Switch) . . . . . . . . . . . 2365
Table 1606 UsedSRBALCSet (Used SRB ALC set) . . . . . . . . . . . . . . . . . . . . . . 2366
Table 1607 AFForHSPATrafficBearers (Activity Factor For HSPA Traffic Bearers) . .
2370
Table 1608 AfHSDPAQoSPri0 (Activity Factor HSDPA QoSPri0) . . . . . . . . . . . . 2372
Table 1609 AfHSDPAQoSPri1 (Activity Factor HSDPA QoSPri1) . . . . . . . . . . . . 2373
Table 1610 AfHSDPAQoSPri10 (Activity Factor HSDPA QoSPri10) . . . . . . . . . . 2374
Table 1611 AfHSDPAQoSPri11 (Activity Factor HSDPA QoSPri11) . . . . . . . . . . 2375
Table 1612 AfHSDPAQoSPri12 (Activity Factor HSDPA QoSPri12) . . . . . . . . . . 2376
Table 1613 AfHSDPAQoSPri13 (Activity Factor HSDPA QoSPri13) . . . . . . . . . . 2377
Table 1614 AfHSDPAQoSPri14 (Activity Factor HSDPA QoSPri14) . . . . . . . . . . 2378
Table 1615 AfHSDPAQoSPri15 (Activity Factor HSDPA QoSPri15) . . . . . . . . . . 2379
Table 1616 AfHSDPAQoSPri2 (Activity Factor HSDPA QoSPri2) . . . . . . . . . . . . 2380
Table 1617 AfHSDPAQoSPri3 (Activity Factor HSDPA QoSPri3) . . . . . . . . . . . . 2381
Table 1618 AfHSDPAQoSPri4 (Activity Factor HSDPA QoSPri4) . . . . . . . . . . . . 2382
Table 1619 AfHSDPAQoSPri5 (Activity Factor HSDPA QoSPri5) . . . . . . . . . . . . 2383
Table 1620 AfHSDPAQoSPri6 (Activity Factor HSDPA QoSPri6) . . . . . . . . . . . . 2384
Table 1621 AfHSDPAQoSPri7 (Activity Factor HSDPA QoSPri7) . . . . . . . . . . . . 2385
Table 1622 AfHSDPAQoSPri8 (Activity Factor HSDPA QoSPri8) . . . . . . . . . . . . 2386
Table 1623 AfHSDPAQoSPri9 (Activity Factor HSDPA QoSPri9) . . . . . . . . . . . . 2387
Table 1624 AfHSUPAQoSPri0 (Activity Factor HSUPA QoSPri0) . . . . . . . . . . . . 2388
DN00211177
Issue 12B
Id:0900d805809d7397
145
WCDMA Radio Network Configuration Parameters
Table 1625 AfHSUPAQoSPri1 (Activity Factor HSUPA QoSPri1) . . . . . . . . . . . . 2389
Table 1626 AfHSUPAQoSPri10 (Activity Factor HSUPA QoSPri10) . . . . . . . . . . 2390
Table 1627 AfHSUPAQoSPri11 (Activity Factor HSUPA QoSPri11) . . . . . . . . . . 2391
Table 1628 AfHSUPAQoSPri12 (Activity Factor HSUPA QoSPri12) . . . . . . . . . . 2392
Table 1629 AfHSUPAQoSPri13 (Activity Factor HSUPA QoSPri13) . . . . . . . . . . 2393
Table 1630 AfHSUPAQoSPri14 (Activity Factor HSUPA QoSPri14) . . . . . . . . . . 2394
Table 1631 AfHSUPAQoSPri15 (Activity Factor HSUPA QoSPri15) . . . . . . . . . . 2395
Table 1632 AfHSUPAQoSPri2 (Activity Factor HSUPA QoSPri2) . . . . . . . . . . . . 2396
Table 1633 AfHSUPAQoSPri3 (Activity Factor HSUPA QoSPri3) . . . . . . . . . . . . 2397
Table 1634 AfHSUPAQoSPri4 (Activity Factor HSUPA QoSPri4) . . . . . . . . . . . . 2398
Table 1635 AfHSUPAQoSPri5 (Activity Factor HSUPA QoSPri5) . . . . . . . . . . . . 2399
Table 1636 AfHSUPAQoSPri6 (Activity Factor HSUPA QoSPri6) . . . . . . . . . . . . 2400
Table 1637 AfHSUPAQoSPri7 (Activity Factor HSUPA QoSPri7) . . . . . . . . . . . . 2401
Table 1638 AfHSUPAQoSPri8 (Activity Factor HSUPA QoSPri8) . . . . . . . . . . . . 2402
Table 1639 AfHSUPAQoSPri9 (Activity Factor HSUPA QoSPri9) . . . . . . . . . . . . 2403
Table 1640 FallbackForDCHQoSPri0 (Fallback for DCH QoS Priority 0 Mapping) . . .
2404
Table 1641 FallbackForDCHQoSPri1 (Fallback for DCH QoS Priority 1 Mapping) . . .
2405
Table 1642 FallbackForDCHQoSPri10 (Fallback for DCH QoS Priority 10 Mapping) .
2406
Table 1643 FallbackForDCHQoSPri11 (Fallback for DCH QoS Priority 11 Mapping) .
2407
Table 1644 FallbackForDCHQoSPri12 (Fallback for DCH QoS Priority 12 Mapping) .
2408
Table 1645 FallbackForDCHQoSPri13 (Fallback for DCH QoS Priority 13 Mapping) .
2409
Table 1646 FallbackForDCHQoSPri14 (Fallback for DCH QoS Priority 14 Mapping) .
2410
Table 1647 FallbackForDCHQoSPri15 (Fallback for DCH QoS Priority 15 Mapping) .
2412
Table 1648 FallbackForDCHQoSPri2 (Fallback for DCH QoS Priority 2 Mapping) . . .
2413
Table 1649 FallbackForDCHQoSPri3 (Fallback for DCH QoS Priority 3 Mapping) . . .
2414
Table 1650 FallbackForDCHQoSPri4 (Fallback for DCH QoS Priority 4 Mapping) . . .
2415
Table 1651 FallbackForDCHQoSPri5 (Fallback for DCH QoS Priority 5 Mapping) . . .
2416
Table 1652 FallbackForDCHQoSPri6 (Fallback for DCH QoS Priority 6 Mapping) . . .
2417
Table 1653 FallbackForDCHQoSPri7 (Fallback for DCH QoS Priority 7 Mapping) . . .
2418
Table 1654 FallbackForDCHQoSPri8 (Fallback for DCH QoS Priority 8 Mapping) . . .
2420
Table 1655 FallbackForDCHQoSPri9 (Fallback for DCH QoS Priority 9 Mapping) . . .
2421
Table 1656 FallbackForHSPAQoSPri0 (Fallback for HSPA QoS Priority 0 Mapping) .
2422
Table 1657 FallbackForHSPAQoSPri1 (Fallback for HSPA QoS Priority 1 Mapping) .
146
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
2423
Table 1658 FallbackForHSPAQoSPri10 (Fallback for HSPA QoS Priority 10 Mapping)
2424
Table 1659 FallbackForHSPAQoSPri11 (Fallback for HSPA QoS Priority 11 Mapping)
2425
Table 1660 FallbackForHSPAQoSPri12 (Fallback for HSPA QoS Priority 12 Mapping)
2426
Table 1661 FallbackForHSPAQoSPri13 (Fallback for HSPA QoS Priority 13 Mapping)
2428
Table 1662 FallbackForHSPAQoSPri14 (Fallback for HSPA QoS Priority 14 Mapping)
2429
Table 1663 FallbackForHSPAQoSPri15 (Fallback for HSPA QoS Priority 15 Mapping)
2430
Table 1664 FallbackForHSPAQoSPri2 (Fallback for HSPA QoS Priority 2 Mapping) .
2431
Table 1665 FallbackForHSPAQoSPri3 (Fallback for HSPA QoS Priority 3 Mapping) .
2432
Table 1666 FallbackForHSPAQoSPri4 (Fallback for HSPA QoS Priority 4 Mapping) .
2433
Table 1667 FallbackForHSPAQoSPri5 (Fallback for HSPA QoS Priority 5 Mapping) .
2434
Table 1668 FallbackForHSPAQoSPri6 (Fallback for HSPA QoS Priority 6 Mapping) .
2436
Table 1669 FallbackForHSPAQoSPri7 (Fallback for HSPA QoS Priority 7 Mapping) .
2437
Table 1670 FallbackForHSPAQoSPri8 (Fallback for HSPA QoS Priority 8 Mapping) .
2438
Table 1671 FallbackForHSPAQoSPri9 (Fallback for HSPA QoS Priority 9 Mapping) .
2439
Table 1672 QosPriToAAL2PT (Qos Priority To AAL2PT ) . . . . . . . . . . . . . . . . . . 2440
Table 1673 CSTrafficToAAL2PT (CS Traffic to AAL2 Path Type mapping) . . . . 2443
Table 1674 DCHQoSPri0ToAAL2PT (DCH QoSPri0 to AAL2 Path Type mapping) . .
2444
Table 1675 DCHQoSPri10ToAAL2PT (DCH QoSPri10 to AAL2 Path Type mapping)
2446
Table 1676 DCHQoSPri11ToAAL2PT (DCH QoSPri11 to AAL2 Path Type mapping)
2448
Table 1677 DCHQoSPri12ToAAL2PT (DCH QoSPri12 to AAL2 Path Type mapping)
2449
Table 1678 DCHQoSPri13ToAAL2PT (DCH QoSPri13 to AAL2 Path Type mapping)
2451
Table 1679 DCHQoSPri14ToAAL2PT (DCH QoSPri14 to AAL2 Path Type mapping)
2453
Table 1680 DCHQoSPri15ToAAL2PT (DCH QoSPri15 to AAL2 Path Type mapping)
2454
Table 1681 DCHQoSPri1ToAAL2PT (DCH QoSPri1 to AAL2 Path Type mapping) . .
2456
Table 1682 DCHQoSPri2ToAAL2PT (DCH QoSPri2 to AAL2 Path Type mapping) . .
2458
Table 1683 DCHQoSPri3ToAAL2PT (DCH QoSPri3 to AAL2 Path Type mapping) . .
2459
DN00211177
Issue 12B
Id:0900d805809d7397
147
WCDMA Radio Network Configuration Parameters
Table 1684 DCHQoSPri4ToAAL2PT (DCH QoSPri4 to AAL2 Path Type mapping) . .
2461
Table 1685 DCHQoSPri5ToAAL2PT (DCH QoSPri5 to AAL2 Path Type mapping) . .
2463
Table 1686 DCHQoSPri6ToAAL2PT (DCH QoSPri6 to AAL2 Path Type mapping) . .
2464
Table 1687 DCHQoSPri7ToAAL2PT (DCH QoSPri7 to AAL2 Path Type mapping) . .
2466
Table 1688 DCHQoSPri8ToAAL2PT (DCH QoSPri8 to AAL2 Path Type mapping) . .
2468
Table 1689 DCHQoSPri9ToAAL2PT (DCH QoSPri9 to AAL2 Path Type mapping) . .
2469
Table 1690 HSPAQoSPri0ToAAL2PT (HSPA QoSPri0 to AAL2 Path Type mapping)
2471
Table 1691 HSPAQoSPri10ToAAL2PT (HSPA QoSPri10 to AAL2 Path Type
mapping) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2473
Table 1692 HSPAQoSPri11ToAAL2PT (HSPA QoSPri11 to AAL2 Path Type
mapping) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2475
Table 1693 HSPAQoSPri12ToAAL2PT (HSPA QoSPri12 to AAL2 Path Type
mapping) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2477
Table 1694 HSPAQoSPri13ToAAL2PT (HSPA QoSPri13 to AAL2 Path Type
mapping) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2479
Table 1695 HSPAQoSPri14ToAAL2PT (HSPA QoSPri14 to AAL2 Path Type
mapping) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2481
Table 1696 HSPAQoSPri15ToAAL2PT (HSPA QoSPri15 to AAL2 Path Type
mapping) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2483
Table 1697 HSPAQoSPri1ToAAL2PT (HSPA QoSPri1 to AAL2 Path Type mapping)
2485
Table 1698 HSPAQoSPri2ToAAL2PT (HSPA QoSPri2 to AAL2 Path Type mapping)
2487
Table 1699 HSPAQoSPri3ToAAL2PT (HSPA QoSPri3 to AAL2 Path Type mapping)
2489
Table 1700 HSPAQoSPri4ToAAL2PT (HSPA QoSPri4 to AAL2 Path Type mapping)
2491
Table 1701 HSPAQoSPri5ToAAL2PT (HSPA QoSPri5 to AAL2 Path Type mapping)
2493
Table 1702 HSPAQoSPri6ToAAL2PT (HSPA QoSPri6 to AAL2 Path Type mapping)
2495
Table 1703 HSPAQoSPri7ToAAL2PT (HSPA QoSPri7 to AAL2 Path Type mapping)
2497
Table 1704 HSPAQoSPri8ToAAL2PT (HSPA QoSPri8 to AAL2 Path Type mapping)
2499
Table 1705 HSPAQoSPri9ToAAL2PT (HSPA QoSPri9 to AAL2 Path Type mapping)
2501
Table 1706 PchFachRachToAAL2PT (PCH FACH to AAL2 Path Type mapping) 2503
Table 1707 SRBToAAL2PT (SRB to AAL2 Path Type mapping) . . . . . . . . . . . . . 2505
Table 1708 QosPriToDSCP (Qos Priority To DSCP) . . . . . . . . . . . . . . . . . . . . . . 2506
Table 1709 CSTrafficToDSCP (CS Traffic to DSCP mapping) . . . . . . . . . . . . . . . 2509
Table 1710 DCHQoSPri0ToDSCP (DCH QoSPri0 to DSCP mapping) . . . . . . . . 2510
Table 1711 DCHQoSPri10ToDSCP (DCH QoSPri10 to DSCP mapping) . . . . . . 2511
148
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1712 DCHQoSPri11ToDSCP (DCH QoSPri11 to DSCP mapping) . . . . . . 2512
Table 1713 DCHQoSPri12ToDSCP (DCH QoSPri12 to DSCP mapping) . . . . . . 2513
Table 1714 DCHQoSPri13ToDSCP (DCH QoSPri13 to DSCP mapping) . . . . . . 2514
Table 1715 DCHQoSPri14ToDSCP (DCH QoSPri14 to DSCP mapping) . . . . . . 2516
Table 1716 DCHQoSPri15ToDSCP (DCH QoSPri15 to DSCP mapping) . . . . . . 2517
Table 1717 DCHQoSPri1ToDSCP (DCH QoSPri1 to DSCP mapping) . . . . . . . . 2518
Table 1718 DCHQoSPri2ToDSCP (DCH QoSPri2 to DSCP mapping) . . . . . . . . 2519
Table 1719 DCHQoSPri3ToDSCP (DCH QoSPri3 to DSCP mapping) . . . . . . . . 2520
Table 1720 DCHQoSPri4ToDSCP (DCH QoSPri4 to DSCP mapping) . . . . . . . . 2521
Table 1721 DCHQoSPri5ToDSCP (DCH QoSPri5 to DSCP mapping) . . . . . . . . 2522
Table 1722 DCHQoSPri6ToDSCP (DCH QoSPri6 to DSCP mapping) . . . . . . . . 2524
Table 1723 DCHQoSPri7ToDSCP (DCH QoSPri7 to DSCP mapping) . . . . . . . . 2525
Table 1724 DCHQoSPri8ToDSCP (DCH QoSPri8 to DSCP mapping) . . . . . . . . 2526
Table 1725 DCHQoSPri9ToDSCP (DCH QoSPri9 to DSCP mapping) . . . . . . . . 2527
Table 1726 HSPAQoSPri0ToDSCP (HSPA QoSPri0 to DSCP mapping) . . . . . . 2528
Table 1727 HSPAQoSPri10ToDSCP (HSPA QoSPri10 to DSCP mapping) . . . . 2529
Table 1728 HSPAQoSPri11ToDSCP (HSPA QoSPri11 to DSCP mapping) . . . . 2530
Table 1729 HSPAQoSPri12ToDSCP (HSPA QoSPri12 to DSCP mapping) . . . . 2532
Table 1730 HSPAQoSPri13ToDSCP (HSPA QoSPri13 to DSCP mapping) . . . . 2533
Table 1731 HSPAQoSPri14ToDSCP (HSPA QoSPri14 to DSCP mapping) . . . . 2534
Table 1732 HSPAQoSPri15ToDSCP (HSPA QoSPri15 to DSCP mapping) . . . . 2535
Table 1733 HSPAQoSPri1ToDSCP (HSPA QoSPri1 to DSCP mapping) . . . . . . 2536
Table 1734 HSPAQoSPri2ToDSCP (HSPA QoSPri2 to DSCP mapping) . . . . . . 2538
Table 1735 HSPAQoSPri3ToDSCP (HSPA QoSPri3 to DSCP mapping) . . . . . . 2539
Table 1736 HSPAQoSPri4ToDSCP (HSPA QoSPri4 to DSCP mapping) . . . . . . 2540
Table 1737 HSPAQoSPri5ToDSCP (HSPA QoSPri5 to DSCP mapping) . . . . . . 2541
Table 1738 HSPAQoSPri6ToDSCP (HSPA QoSPri6 to DSCP mapping) . . . . . . 2542
Table 1739 HSPAQoSPri7ToDSCP (HSPA QoSPri7 to DSCP mapping) . . . . . . 2544
Table 1740 HSPAQoSPri8ToDSCP (HSPA QoSPri8 to DSCP mapping) . . . . . . 2545
Table 1741 HSPAQoSPri9ToDSCP (HSPA QoSPri9 to DSCP mapping) . . . . . . 2546
Table 1742 PchFachRachToDSCP (PCH FACH RACH to DSCP mapping) . . . 2547
Table 1743 SRBToDSCP (SRB to DSCP mapping) . . . . . . . . . . . . . . . . . . . . . . 2548
Table 1744 TQMChangeOrigin (TQM Change origin) . . . . . . . . . . . . . . . . . . . . . 2549
Table 1745 TQMId (TQM object identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2550
Table 1746 ControllerIdPair (Neighbouring FD-BTS Identifier and Its SRNC Identifier)
2552
Table 1747 IHSPAadapterId (I-HSPA Adapter Identifier) . . . . . . . . . . . . . . . . . . 2553
Table 1748 ServingRNCId (Serving RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . 2553
Table 1749 DediMeasRepPeriodCSdata (Dedicated Measurement Reporting Period
CS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2554
Table 1750 DediMeasRepPeriodPSdata (Dedicated Measurement Reporting Period
PS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2555
Table 1751 DedicatedMeasReportPeriod (Dedicated Measurement Reporting Period)
2556
Table 1752 HARQRVConfiguration (HARQ RV Configuration) . . . . . . . . . . . . . . 2557
Table 1753 MeasFiltCoeff (Measurement filter coefficient) . . . . . . . . . . . . . . . . . 2559
Table 1754 NodeBRABReconfigSupport (NodeB PS RAB reconfiguration Support) .
2560
DN00211177
Issue 12B
Id:0900d805809d7397
149
WCDMA Radio Network Configuration Parameters
Table 1755 VBTSChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . . 2561
Table 1756 VBTSId (VBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2563
Table 1757 CSAMRModeSET (Configured CS AMR mode sets) . . . . . . . . . . . . 2564
Table 1758 CSAMRModeSETWB (Configured CS WAMR mode sets) . . . . . . . . 2565
Table 1759 DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . . 2567
Table 1760 EDCHMinimumSetETFCI (E-DCH minimum set E-TFCI) . . . . . . . . . 2568
Table 1761 EbNoSetIdentifier (Eb/No parameter set identifier) . . . . . . . . . . . . . . 2569
Table 1762 FastActOfTargetServCell (Faster Activation Of Target Serving Cell) 2570
Table 1763 FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . . 2571
Table 1764 HHoMaxAllowedBitrateDL (Maximum allowed DL user bit rate in HHO) . .
2573
Table 1765 HHoMaxAllowedBitrateUL (Maximum allowed UL user bit rate in HHO) . .
2574
Table 1766 HSDPAFmcgIdentifier (HSDPA FMCG identifier) . . . . . . . . . . . . . . . 2575
Table 1767 HSDPAFmciIdentifier (HSDPA FMCI identifier) . . . . . . . . . . . . . . . . . 2576
Table 1768 HSDPAFmcsIdentifier (HSDPA FMCS identifier) . . . . . . . . . . . . . . . 2577
Table 1769 HSDPAHopsIdentifier (HSDPA HOPS identifier) . . . . . . . . . . . . . . . . 2578
Table 1770 HSDPAenabled (HSDPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2579
Table 1771 HSPAFmcsIdentifier (HSPA FMCS identifier) . . . . . . . . . . . . . . . . . . 2581
Table 1772 HSPASCCSpecificATO (HSPA SCC Specific ATO Value) . . . . . . . . 2582
Table 1773 HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay) . 2583
Table 1774 HSUPAEnabled (HSUPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2584
Table 1775 InitialBitRateDL (Initial bit rate in downlink) . . . . . . . . . . . . . . . . . . . . 2585
Table 1776 InitialBitRateUL (Initial bit rate in uplink) . . . . . . . . . . . . . . . . . . . . . . 2587
Table 1777 LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2589
Table 1778 MaxBitRateDLPSNRT (Maximum downlink bit rate for PS domain NRT
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2590
Table 1779 MaxBitRateULPSNRT (Maximum uplink bit rate for PS domain NRT data)
2591
Table 1780 MaxTotalUplinkSymbolRate (Maximum total uplink symbol rate) . . . 2593
Table 1781 MinAllowedBitRateDL (Minimum allowed bit rate in downlink) . . . . . 2594
Table 1782 MinAllowedBitRateUL (Minimum allowed bit rate in uplink) . . . . . . . . 2595
Table 1783 NrtFmcgIdentifier (NRT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . 2597
Table 1784 NrtFmciIdentifier (NRT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2598
Table 1785 NrtFmcsIdentifier (NRT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . . 2599
Table 1786 NrtHopgIdentifier (NRT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . 2600
Table 1787 NrtHopiIdentifier (NRT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2601
Table 1788 NrtHopsIdentifier (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . 2602
Table 1789 PowerOffsetUpdMsgSize (Power Offset Update Message Size
Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2603
Table 1790 PtxOffsetHSSCCH (The power offset of the HS-SCCH) . . . . . . . . . . 2604
Table 1791 RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2605
Table 1792 RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2606
Table 1793 RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2608
Table 1794 RTwithHSDPAFmciIdentifier (HSDPA FMCI identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2609
150
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1795 RTwithHSDPAFmcsIdentifier (HSDPA FMCS identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2610
Table 1796 RTwithHSDPAHopsIdentifier (HSDPA HOPS identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2611
Table 1797 RelocComm_in_InterRNC_HHO (Usage of Relocation Commit procedure
in inter RNC HHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2612
Table 1798 RtFmcgIdentifier (RT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2614
Table 1799 RtFmciIdentifier (RT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2615
Table 1800 RtFmcsIdentifier (RT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2616
Table 1801 RtHopgIdentifier (RT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2616
Table 1802 RtHopiIdentifier (RT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2617
Table 1803 RtHopsIdentifier (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2618
Table 1804 RxDivIndicator (Rx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . 2619
Table 1805 SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . 2620
Table 1806 SRBHopsIdentifier (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . 2621
Table 1807 VCELChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . 2622
Table 1808 VCELId (VCEL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2624
Table 1809 WACSetIdentifier (WAC Parameter Set Identifier) . . . . . . . . . . . . . . 2624
Table 1810 DCHUtilRelAveWin (Window size for the release throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2626
Table 1811 DCHUtilRelThrDL (Threshold for the downlink DCH release
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2627
Table 1812 DCHUtilRelThrUL (Threshold for the uplink DCH release measurement)
2630
Table 1813 DCHUtilRelTimeToTrigger (Time to trigger for the release throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2632
Table 1814 EDCHMACdFlowThroughputAveWin (Window size of E-DCH MAC-d flow
throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2633
Table 1815 EDCHMACdFlowThroughputRelThr (Low throughput threshold of the EDCH MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2634
Table 1816 EDCHMACdFlowThroughputTimetoTrigger (Low throughput time to trigger
of the E-DCH MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2635
Table 1817 HSDPAInitialBRULStrNRT (Initial bitrate for HSDPA UL DCH for NRT with
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2636
Table 1818 HSDPAMaxBitrateUL (Maximum bit rate for HSDPA UL DCH return
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2638
Table 1819 HSDPAMinBRULStrNRT (Min bitrate for HSDPA UL DCH for NRT with
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2639
Table 1820 HSDPAinitialBitrateUL (Initial bitrate for HSDPA associated UL DCH) . .
2641
Table 1821 HSDPAminAllowedBitrateUL (Minimum bitrate for HSDPA associated UL
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2642
Table 1822 InactCPCBatOptT (Inactive CPC user with battery optimization timer) . .
2643
Table 1823 InactCPCNoBatOptT (Inactive CPC user without battery optimization
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2646
Table 1824 InactHSRACH (Inactive HS-RACH capable UE) . . . . . . . . . . . . . . . 2652
Table 1825 InactNonCPCBatOptT (Inactive nonCPC user with battery optimization
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2653
Table 1826 InactNonCPCNoBatOptT (Inactive nonCPC user without battery optimiza-
DN00211177
Issue 12B
Id:0900d805809d7397
151
WCDMA Radio Network Configuration Parameters
tion timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2659
Table 1827 InactivityTimerDownlinkDCH (Inactivity timer for downlink DCH) . . . 2665
Table 1828 InactivityTimerDownlinkDCH128 (Inactivity timer for downlink 128kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2666
Table 1829 InactivityTimerDownlinkDCH16 (Inactivity timer for downlink 16kbps DCH)
2667
Table 1830 InactivityTimerDownlinkDCH256 (Inactivity timer for downlink 256kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2668
Table 1831 InactivityTimerDownlinkDCH32 (Inactivity timer for downlink 32kbps DCH)
2669
Table 1832 InactivityTimerDownlinkDCH320 (Inactivity timer for downlink 320kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2670
Table 1833 InactivityTimerDownlinkDCH384 (Inactivity timer for downlink 384kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2671
Table 1834 InactivityTimerDownlinkDCH64 (Inactivity timer for downlink 64kbps DCH)
2672
Table 1835 InactivityTimerDownlinkDCH8 (Inactivity timer for downlink 8kbps DCH) .
2673
Table 1836 InactivityTimerUplinkDCH (Inactivity timer for uplink DCH) . . . . . . . . 2674
Table 1837 InactivityTimerUplinkDCH128 (Inactivity timer for uplink 128kbps DCH) . .
2676
Table 1838 InactivityTimerUplinkDCH16 (Inactivity timer for uplink 16kbps DCH) . . . .
2677
Table 1839 InactivityTimerUplinkDCH256 (Inactivity timer for uplink 256kbps DCH) . .
2678
Table 1840 InactivityTimerUplinkDCH32 (Inactivity timer for uplink 32kbps DCH) . . . .
2679
Table 1841 InactivityTimerUplinkDCH320 (Inactivity timer for uplink 320kbps DCH) . .
2680
Table 1842 InactivityTimerUplinkDCH384 (Inactivity timer for uplink 384kbps DCH) . .
2681
Table 1843 InactivityTimerUplinkDCH64 (Inactivity timer for uplink 64kbps DCH) . . . .
2682
Table 1844 InactivityTimerUplinkDCH8 (Inactivity timer for uplink 8kbps DCH) . . 2683
Table 1845 MACdflowthroughputAveWin (Window size of the MAC-d flow throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2684
Table 1846 MACdflowutilRelThr (Low utilisation threshold of the MAC-d flow) . . 2685
Table 1847 MACdflowutilTimetoTrigger (Low utilization time to trigger of the MAC-d
flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2686
Table 1848 MSActivitySupervision (Time supervision of user inactivity (for NRT RBs))
2687
Table 1849 PrxNoiseMaxTuneAbsolute (Absolute limit in uplink noise autotuning) . . .
2689
Table 1850 TrafVolPendingTimeDL (Downlink traffic volume measurement pending
time after trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2690
Table 1851 TrafVolPendingTimeUL (Uplink traffic volume measurement pending time
after trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2692
Table 1852 TrafVolThresholdULLow (Uplink traffic volume measurement low
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2694
Table 1853 UL_DL_activation_timer (UL/DL activation timer) . . . . . . . . . . . . . . . 2696
152
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1854 WACChangeOrigin (WAC Change origin) . . . . . . . . . . . . . . . . . . . . 2696
Table 1855 WACId (WAC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2698
Table 1856 WaitTimeRRC (Wait time in RRC connection request rejection) . . . 2699
Table 1857 WaitTimeRRCbackground (RRC wait time for background causes) 2700
Table 1858 WaitTimeRRCconversational (RRC wait time for conversational causes)
2701
Table 1859 WaitTimeRRCemergency (RRC wait time for emergency causes) 2702
Table 1860 WaitTimeRRChighPrioritySignalling (RRC wait time for high priority signalling causes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2703
Table 1861 WaitTimeRRCinterRATreselection (RRC wait time for inter-RAT re-selection causes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2704
Table 1862 WaitTimeRRCinteractive (RRC wait time for interactive causes) . . 2705
Table 1863 WaitTimeRRClowPrioritySignalling (RRC wait time for low priority signalling causes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2707
Table 1864 WaitTimeRRCother (RRC wait time for other causes) . . . . . . . . . . . 2708
Table 1865 WaitTimeRRCregistration (RRC wait time for registration causes) 2709
Table 1866 WaitTimeRRCstreaming (RRC wait time for streaming causes) . . 2710
Table 1867 WaitTimeRRCsubscribed (RRC wait time for subscribed causes) . 2711
Table 1868 WaitTimeRRCunknown (RRC wait time for unknown causes) . . . . 2712
Table 1869 AuthorisedNetworkId (Authorised Network Identifier) . . . . . . . . . . . . 2713
Table 1870 AuthorisedNetworkPLMN (Authorised Network PLMN) . . . . . . . . . . 2714
Table 1871 AuthorisedNetworkMCC (Authorised Network Mobile Country Code) 2715
Table 1872 AuthorisedNetworkMNC (Authorised Network Mobile Network Code) . . .
2716
Table 1873 AuthorisedNetworkMNClength (Authorised Network Mobile Network Code
Length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2717
Table 1874 Technology (Technology used in the Authorised Network) . . . . . . . 2717
Table 1875 WANEChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 2718
Table 1876 WANEName (WANE Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2720
Table 1877 ATMInterfaceID (ATM interface identifier) . . . . . . . . . . . . . . . . . . . . 2721
Table 1878 AdminWBTSState (Admin WBTS State) . . . . . . . . . . . . . . . . . . . . . . 2722
Table 1879 BTSAdditionalInfo (BTS Additional Information) . . . . . . . . . . . . . . . . 2723
Table 1880 BTSFallbackEnabled (BTS Fallback enabled) . . . . . . . . . . . . . . . . . 2724
Table 1881 BTSIPAddress (BTS O&M IP address) . . . . . . . . . . . . . . . . . . . . . . . 2725
Table 1882 BTSSupportForHSPACM (BTS Support For HSPA CM) . . . . . . . . . 2726
Table 1883 BlindHOIntraBTSQCheck (Blind HO Intra BTS Quality Check) . . . . 2727
Table 1884 BlindTFdetectionUsage (Blind transport format detection capability of
BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2728
Table 1885 BroadcastSIB15 (Broadcast SIB15) . . . . . . . . . . . . . . . . . . . . . . . . . 2729
Table 1886 BroadcastSIB15_2 (Broadcast SIB15.2) . . . . . . . . . . . . . . . . . . . . . . 2730
Table 1887 BroadcastSIB15_3 (Broadcast SIB15.3) . . . . . . . . . . . . . . . . . . . . . . 2731
Table 1888 COCOId (Connection Configuration Identifier) . . . . . . . . . . . . . . . . . 2732
Table 1889 DCHnumberRL (Number of DCHs per RL capability of BTS) . . . . . . 2734
Table 1890 DCNLinkStatus (O&M DCN link status) . . . . . . . . . . . . . . . . . . . . . . 2735
Table 1891 DCNSecurityStatus (O&M DCN secure link status) . . . . . . . . . . . . . 2736
Table 1892 DLORLAveragingWindowSize (Tx power of radio link averaging window
size for DLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2737
Table 1893 DSCPHigh (DSCP high priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2738
DN00211177
Issue 12B
Id:0900d805809d7397
153
WCDMA Radio Network Configuration Parameters
Table 1894 DSCPLow (DSCP Low priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2740
Table 1895 DSCPMedDCH (DSCP medium priority DCH) . . . . . . . . . . . . . . . . . 2741
Table 1896 DSCPMedHSPA (DSCP Medium priority HSPA) . . . . . . . . . . . . . . . 2742
Table 1897 DediMeasRepPeriodCSdata (Dedicated Measurement Reporting Period
CS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2743
Table 1898 DediMeasRepPeriodPSdata (Dedicated Measurement Reporting Period
PS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2744
Table 1899 DedicatedMeasReportPeriod (Dedicated Measurement Reporting Period)
2745
Table 1900 DelayThresholdMax (Maximum Threshold for HSUPA congestion handling
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2746
Table 1901 DelayThresholdMax2msTTI (Maximum Threshold for HSUPA congestion
delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2748
Table 1902 DelayThresholdMid (Middle Threshold value for HSUPA congestion
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2749
Table 1903 DelayThresholdMid2msTTI (Middle Threshold for HSUPA congestion delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2750
Table 1904 DelayThresholdMin (Minimum Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2751
Table 1905 DelayThresholdMin2msTTI (Minimum Threshold for HSUPA congestion
delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2752
Table 1906 HARQRVConfiguration (HARQ RV Configuration) . . . . . . . . . . . . . . 2754
Table 1907 HSDPA14MbpsPerUser (HSDPA14MbpsPerUser) . . . . . . . . . . . . . . 2755
Table 1908 HSDPACCEnabled (HSDPA Congestion Control activation) . . . . . . 2756
Table 1909 HSDPAIurWeight (HSDPA Iur Weight) . . . . . . . . . . . . . . . . . . . . . . . 2758
Table 1910 HSDPAOperIdWeightPair (HSDPA Operator Identifier Weight Pair) . 2759
Table 1911 HSDPAOperatorId (HSDPA Operator Identifier) . . . . . . . . . . . . . . . . 2760
Table 1912 HSDPAOperatorWeight (HSDPA Operator Weight) . . . . . . . . . . . . . 2761
Table 1913 HSDPAULCToDSCP (HSDPA UL FP Control traffic to DSCP mapping) .
2763
Table 1914 HSDPAUserHysterisis (HSDPA User Hysterisis) . . . . . . . . . . . . . . . 2764
Table 1915 HSDPAUserThreshold (HSDPA User Threshold) . . . . . . . . . . . . . . . 2765
Table 1916 HSUPACCEnabled (HSUPA Congestion Control activation) . . . . . . 2766
Table 1917 HSUPADLCToDSCP (HSUPA DL FP Control traffic to DSCP mapping) .
2767
Table 1918 HSUPAXUsersEnabled (HSUPA x users enabled) . . . . . . . . . . . . . . 2768
Table 1919 ICREnabled (ICR Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2771
Table 1920 IPBasedRouteIdIub (IP Based Route Id Iub) . . . . . . . . . . . . . . . . . . . 2772
Table 1921 IPBasedRouteIdIub2 (IP Based Route Id Iub 2) . . . . . . . . . . . . . . . . 2773
Table 1922 IPBasedRouteIdIub3 (IP Based Route Id Iub 3) . . . . . . . . . . . . . . . . 2774
Table 1923 IPBasedRouteIdIub4 (IP Based Route Id Iub 4) . . . . . . . . . . . . . . . . 2776
Table 1924 IPNBId (IPNB object identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2777
Table 1925 InactCACThresholdATM (Inactive users CAC Threshold for ATM) . . 2779
Table 1926 InactCACThresholdIP (Inactive users CAC Threshold for IP) . . . . . . 2780
Table 1927 InactUsersCIDThreshold (Inactive users Connection ID Threshold) . 2781
Table 1928 IntelligentSDPrioHO (Priorized Handover Type in Intelligent Shutdown) .
2782
Table 1929 IubTransportFallback (Iub Transport Fallback Mapping) . . . . . . . . . . 2783
Table 1930 IubTransportMedia (Iub Transport Media Selection) . . . . . . . . . . . . . 2785
154
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1931 IubTransportSharing (Iub Transport Sharing activation) . . . . . . . . . . 2788
Table 1932 LoadControlPeriodPS (PS load control period) . . . . . . . . . . . . . . . . 2789
Table 1933 MDCBufferingTime (MDC Buffering Time) . . . . . . . . . . . . . . . . . . . . 2790
Table 1934 MaxDCHuserRateRLDL (Max DL user rate per RL) . . . . . . . . . . . . . 2791
Table 1935 MaxDCHuserRateRLUL (Max UL user rate per RL) . . . . . . . . . . . . . 2792
Table 1936 MaxFPDLFrameSizeIub (Maximum FP downlink frame size Iub) . . 2793
Table 1937 MaxNumberEDCHLCG (Maximum number of E-DCHs in the local cell
group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2795
Table 1938 MeasFiltCoeff (Measurement filter coefficient) . . . . . . . . . . . . . . . . . 2796
Table 1939 MinUDPPortIub (Minimum UDP port value for the Iub) . . . . . . . . . . 2798
Table 1940 NBAPCommMode (NBAP Communication Mode) . . . . . . . . . . . . . . 2799
Table 1941 NESWVersion (NE-SW-Version) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2800
Table 1942 NEType (NE-type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2801
Table 1943 NbrOfOverbookedHSDPAUsers (Number of overbooked HSDPA users)
2802
Table 1944 NodeBRABReconfigSupport (NodeB PS RAB reconfiguration Support) .
2803
Table 1945 OverbookingSwitch (Overbooking Switch) . . . . . . . . . . . . . . . . . . . . 2804
Table 1946 PDUSize656WithHSDSCH (Usage of RLC PDU size 656 with HS-DSCH)
2805
Table 1947 PSAveragingWindowSize (Load measurement averaging window size for
packet scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2807
Table 1948 PSRLAveragingWindowSize (Tx power of radio link averaging window size
for PS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2808
Table 1949 PWSMAVTrafficVERLogic (Traffic verification logic in PWSM cell activation process) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2810
Table 1950 PWSMEnableWakeUpTime (Enable cell activation based on time of day)
2811
Table 1951 PWSMInUse (The PWSM usage in BTS) . . . . . . . . . . . . . . . . . . . . . 2812
Table 1952 PWSMRemCellSDBeginHour (PWSM Shutdown Time Begin Hour for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2814
Table 1953 PWSMRemCellSDBeginMin (PWSM Shutdown Time Begin Minute for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2815
Table 1954 PWSMRemCellSDEndHour (PWSM Shutdown Time End Hour for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2816
Table 1955 PWSMRemCellSDEndMin (PWSM Shutdown Time End Minute for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2817
Table 1956 PWSMShutdownBeginHour (Hour when the cell shutdown window starts)
2818
Table 1957 PWSMShutdownBeginMin (Minute when the cell shutdown window starts)
2819
Table 1958 PWSMShutdownEndHour (Hour when the cell shutdown window ends) .
2820
Table 1959 PWSMShutdownEndMin (Minute when the cell shutdown window ends)
2822
Table 1960 PWSMWeekday (Weekend for shutdown) . . . . . . . . . . . . . . . . . . . . 2823
Table 1961 ProbabilityFactorMax (ProbabilityFactor for Congestion Indication
sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2824
Table 1962 ProbabilityFactorMax2msTTI (ProbabilityFactor for Congestion Indication
sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2825
DN00211177
Issue 12B
Id:0900d805809d7397
155
WCDMA Radio Network Configuration Parameters
Table 1963 PrxAlpha (Type of measurement filter for uplink total received power) . . .
2826
Table 1964 PrxMeasAveWindow (Number of frames to be used averaging in PrxTotal
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2827
Table 1965 PrxTargetPSAdjustPeriod (PS target tune period in HSPA-DCH interference sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2828
Table 1966 PtxAlpha (Type of measurement filter for downlink total transmitted power)
2829
Table 1967 PtxDPCHmax (DPCH downlink transmission power maximum value) . . .
2830
Table 1968 PtxDPCHmin (DPCH downlink transmission power minimum value) 2832
Table 1969 PtxMeasAveWindow (Number of frames to be used averaging in PtxTotal
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2833
Table 1970 R99OperIdWeightPair (R99 Operator Identifier Weight Pair) . . . . . . 2834
Table 1971 R99OperatorId (R99 Operator Identifier) . . . . . . . . . . . . . . . . . . . . . . 2835
Table 1972 R99OperatorWeight (R99 Operator Weight) . . . . . . . . . . . . . . . . . . . 2836
Table 1973 RACHloadIndicationPeriod (RACH load indication period) . . . . . . . . 2838
Table 1974 RFSharingState (RF Sharing State) . . . . . . . . . . . . . . . . . . . . . . . . . 2839
Table 1975 RRIndPeriod (Radio Resource Indication Period) . . . . . . . . . . . . . . . 2840
Table 1976 RRMULDCHActivityFactor (Average UL DCH data rates for the radio
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2842
Table 1977 RRMULActivityFactorPTT (Average relative UL data rate for RBs of PTT)
2843
Table 1978 RRMULDCHActivityFactorCSAMR (Average UL DCH data rate for RBs of
CS AMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2844
Table 1979 RRMULDCHActivityFactorCSNTData (Average UL DCH data rate for RB
of CS NT-data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2845
Table 1980 RRMULDCHActivityFactorCSTData (Average UL DCH data rate for RB of
CS T-data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2846
Table 1981 RRMULDCHActivityFactorPSBackgr (Average UL DCH data rate for RB of
PS background RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2847
Table 1982 RRMULDCHActivityFactorPSStream (Average UL DCH data rate for RB of
PS Streaming RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2848
Table 1983 RRMULDCHActivityFactorPSTHP1 (Average UL DCH data rate for RB of
PS THP1 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2849
Table 1984 RRMULDCHActivityFactorPSTHP2 (Average UL DCH data rate for RB of
PS THP2 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2850
Table 1985 RRMULDCHActivityFactorPSTHP3 (Average UL DCH data rate for RB of
PS THP3 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2851
Table 1986 RRMULDCHActivityFactorSRB (Average UL DCH data rate for SRB) . . .
2852
Table 1987 ReleaseTimerForSharedHSDPAallocation (Release timer for shared HSDPA allocation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2853
Table 1988 SatelliteIubUsage (Satellite Iub Usage) . . . . . . . . . . . . . . . . . . . . . . . 2854
Table 1989 SchedulingPeriod (Scheduling period) . . . . . . . . . . . . . . . . . . . . . . . . 2856
Table 1990 SharedHSDPAVCCSelectionMethod (Shared HSDPA AAL2 VCC selection method) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2857
Table 1991 SharedHSDPAallocation (Shared HSDPA AAL2 allocation) . . . . . . . 2858
Table 1992 TQMId (TQM object identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2859
Table 1993 TQMId2 (TQM Object Identifier 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2861
156
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 1994 TQMId3 (TQM Object Identifier 3) . . . . . . . . . . . . . . . . . . . . . . . . . . 2862
Table 1995 TQMId4 (TQM Object Identifier 4) . . . . . . . . . . . . . . . . . . . . . . . . . . 2864
Table 1996 TargetId (Network Element Target Identifier) . . . . . . . . . . . . . . . . . . 2865
Table 1997 ToAWEOffsetNRTDCHIP (ToAWE Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2866
Table 1998 ToAWEOffsetRTDCHIP (ToAWE Offset for RT DCH connections over IP)
2867
Table 1999 ToAWSOffsetNRTDCHIP (ToAWS Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2869
Table 2000 ToAWSOffsetRTDCHIP (ToAWS Offset for RT DCH connections over IP)
2870
Table 2001 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2871
Table 2002 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2872
Table 2003 WBTSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 2873
Table 2004 WBTSId (WBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2875
Table 2005 WBTSName (WCDMA BTS name) . . . . . . . . . . . . . . . . . . . . . . . . . . 2875
Table 2006 WBTSSWBuildId (WBTS SW build identifier) . . . . . . . . . . . . . . . . . . 2876
Table 2007 WinACRABsetupDL (DL measurement averaging window for AC) . 2877
Table 2008 WinACRABsetupUL (UL measurement averaging window for AC) . 2878
Table 2009 WinLCHSDPA (PtxnonHSPA averaging window size for LC) . . . . . 2879
Table 2010 WinLCHSUPA (Non E-DCH ST interference averaging window size for
LC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2881
Table 2011 ACBarredList (Access Class Barred list) . . . . . . . . . . . . . . . . . . . . . 2883
Table 2012 AICHTraTime (AICH Transmission Timing) . . . . . . . . . . . . . . . . . . . 2885
Table 2013 AMROverSC (AMROverSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2886
Table 2014 AMROverTransmission (AMROverTransmission) . . . . . . . . . . . . . . 2887
Table 2015 AMROverTxNC (AMROverTxNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2888
Table 2016 AMROverTxNonHSPA (AMROverTxNonHSPA) . . . . . . . . . . . . . . . 2889
Table 2017 AMROverTxTotal (AMROverTxTotal) . . . . . . . . . . . . . . . . . . . . . . . . 2890
Table 2018 AMRSF (AMRSF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2891
Table 2019 AMRTargetSC (AMRTargetSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2892
Table 2020 AMRTargetTransmission (AMRTargetTransmission) . . . . . . . . . . . . 2893
Table 2021 AMRTargetTxNC (AMRTargetTxNC) . . . . . . . . . . . . . . . . . . . . . . . . 2894
Table 2022 AMRTargetTxNonHSPA (AMRTargetTxNonHSPA) . . . . . . . . . . . . . 2895
Table 2023 AMRTargetTxTotal (AMRTargetTxTotal) . . . . . . . . . . . . . . . . . . . . . 2896
Table 2024 AMRUnderSC (AMRUnderSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2897
Table 2025 AMRUnderTransmission (AMRUnderTransmission) . . . . . . . . . . . . 2899
Table 2026 AMRUnderTxNC (AMRUnderTxNC) . . . . . . . . . . . . . . . . . . . . . . . . . 2900
Table 2027 AMRUnderTxNonHSPA (AMRUnderTxNonHSPA) . . . . . . . . . . . . . 2901
Table 2028 AMRUnderTxTotal (AMRUnderTxTotal) . . . . . . . . . . . . . . . . . . . . . . 2902
Table 2029 ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA) . . 2903
Table 2030 AbsPrioCellReselec (Absolute priority level for cell reselection) . . . . 2904
Table 2031 ActivationTimeOffset (Offset for activation time) . . . . . . . . . . . . . . . . 2905
Table 2032 AdminCellState (Administrative Cell State) . . . . . . . . . . . . . . . . . . . . 2907
Table 2033 AdminPICState (Admin PIC state) . . . . . . . . . . . . . . . . . . . . . . . . . . 2908
Table 2034 AllowedPreambleSignatures (Allowed preamble signatures) . . . . . . 2909
Table 2035 AllowedRACHSubChannels (Allowed RACH subchannels) . . . . . . . 2911
Table 2036 AltScramblingCodeCM (Compressed Mode: Alternative scrambling code)
DN00211177
Issue 12B
Id:0900d805809d7397
157
WCDMA Radio Network Configuration Parameters
2912
Table 2037 AmpliRatioOptHSRACH (HS-RACH amplitude ratio optimized for low/high
bit rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2913
Table 2038 AppAwareRANCapability (Application Aware RAN Capability) . . . . . 2914
Table 2039 AppAwareRANEnabled (Application Aware RAN Enabled) . . . . . . . . 2915
Table 2040 AssignedPICPool (Cell assigned to PIC pool) . . . . . . . . . . . . . . . . . . 2916
Table 2041 AutoACDSACRestriction (Domain Specific Access Class Restriction) . . .
2918
Table 2042 AutoACRPrxTotalAvgWs (Automatic Access Class window size for averaging PrxTotal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2920
Table 2043 AutoACResULOLThr (Automatic Access Class Restriction Uplink Overload Threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2922
Table 2044 BlindHOEcNoThrTarget (Blind HO EcNo threshold for target cell) . . 2923
Table 2045 BlindHORSCPThrTarget (Blind HO RSCP threshold for target cell) . 2924
Table 2046 CCHSetupEnabled (RRC Connection Setup on CCH Enabled) . . . . 2925
Table 2047 CIRForFDPCH (Carrier to interference ratio for F-DPCH) . . . . . . . . . 2926
Table 2048 CId (Cell identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2927
Table 2049 CPCEnabled (CPC enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2928
Table 2050 CPICHEcNoSRBMapRRC (CPICH Ec/No thr for SRB mapping in RRC
setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2929
Table 2051 CPICHRSCPSRBMapRRC (CPICH RSCP thr for SRB mapping in RRC
setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2930
Table 2052 CPICHtoRefRABoffset (Offset of the P-CPICH and reference service
powers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2932
Table 2053 CSAMRModeSET (Configured CS AMR mode sets) . . . . . . . . . . . . 2933
Table 2054 CSAMRModeSETWB (Configured CS WAMR mode sets) . . . . . . . . 2935
Table 2055 CSGroupId (Restriction Group Id for Circuit Switched Acces) . . . . . . 2936
Table 2056 CTCHCapaHighPri (CTCH capacity for High Priority CBS messages) . . .
2937
Table 2057 CUCEcNoThreshold (CPICH Ec/No Threshold Value For CUC Usage) . .
2938
Table 2058 CUCRSCPThreshold (CPICH RSCP Threshold Value For CUC Usage) .
2940
Table 2059 CableLoss (Cable Loss) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2942
Table 2060 CellAdditionalInfo (Cell Additional Information) . . . . . . . . . . . . . . . . . 2943
Table 2061 CellBarred (Cell Barred) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2944
Table 2062 CellRange (Cell range) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2945
Table 2063 CellSelQualMeas (Measurement to be used as quality measure) . . . 2947
Table 2064 CellWeightForHSDPALayering (Cell weight for HSDPA layering) . . . 2948
Table 2065 Cell_Reserved (Cell Reserved for operator use) . . . . . . . . . . . . . . . . 2949
Table 2066 CodeTreeOptTimer (Code tree optimisation timer) . . . . . . . . . . . . . . 2951
Table 2067 CodeTreeOptimisation (Code tree optimisation) . . . . . . . . . . . . . . . . 2951
Table 2068 CodeTreeOptimisationGuardTime (Code Tree Optimisation Guard Time)
2952
Table 2069 CodeTreeUsage (Code Tree Usage) . . . . . . . . . . . . . . . . . . . . . . . . . 2953
Table 2070 DBandHSDPAEnabled (Dual Band HSDPA Enabled) . . . . . . . . . . . . 2954
Table 2071 DCellAndMIMOUsage (DC-HSDPA and MIMO Usage) . . . . . . . . . . 2956
Table 2072 DCellHSDPACapaHO (DC HSDPA Capability HO) . . . . . . . . . . . . . . 2957
Table 2073 DCellHSDPAEnabled (DC HSDPA Enabled) . . . . . . . . . . . . . . . . . . 2959
158
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 2074 DCellHSDPAFmcsId (DC HSDPA FMCS Identifier) . . . . . . . . . . . . . 2962
Table 2075 DLLoadStateTTT (DL loaded state time to trigger) . . . . . . . . . . . . . . 2963
Table 2076 DPCHOverHSPDSCHThreshold (NRT DPCH over HS-PDSCH code
offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2965
Table 2077 DPCModeChangeSupport (DPC Mode Change Support) . . . . . . . . 2966
Table 2078 DRRCprxMargin (Prx Margin for DRRC) . . . . . . . . . . . . . . . . . . . . . 2967
Table 2079 DRRCprxOffset (Prx Offset for DRRC) . . . . . . . . . . . . . . . . . . . . . . . 2968
Table 2080 DRRCptxMargin (Ptx Margin for DRRC) . . . . . . . . . . . . . . . . . . . . . . 2969
Table 2081 DRRCptxOffset (Ptx Offset for DRRC) . . . . . . . . . . . . . . . . . . . . . . . 2970
Table 2082 DRXCycleHSFACH (Discontinuous Reception Cycle HS-FACH) . . 2971
Table 2083 DRXInactiveTimerHSFACH (Inactivity Supervision Timer of HS-FACH for
DRX User ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2972
Table 2084 DRXInterruptHSDSCHData (DRX Interruption by HS-DSCH data) . 2973
Table 2085 DefMeasCtrlReading (Deferred Measurement Control Reading) . . . 2974
Table 2086 DeltaPrxMaxDown (Maximum uplink power decrease in packet
scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2975
Table 2087 DeltaPrxMaxUp (Maximum uplink power increase in packet scheduling)
2976
Table 2088 DeltaPtxMaxDown (Maximum downlink power decrease in packet
scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2978
Table 2089 DeltaPtxMaxUp (Maximum downlink power increase in packet scheduling)
2979
Table 2090 DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . 2980
Table 2091 DirectedRRCEnabled (Directed RRC connection setup enabled) . . 2981
Table 2092 DirectedRRCForHSDPALayerEnabled (Directed RRC connection setup
for HSDPA layer enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2982
Table 2093 EDCHCapability (E-DCH Capability) . . . . . . . . . . . . . . . . . . . . . . . . 2984
Table 2094 EDCHMinSetETFCIT0 (E-DCH minimum set E-TFCI 10 ms TTI table 0)
2985
Table 2095 EDCHMinimumSetETFCI (E-DCH minimum set E-TFCI 10 ms TTI table 1)
2986
Table 2096 EDCHOpState (Operational E-DCH state) . . . . . . . . . . . . . . . . . . . . 2987
Table 2097 EVAMCapability (EVAM capability) . . . . . . . . . . . . . . . . . . . . . . . . . 2988
Table 2098 EVAMInUse (EVAM in use) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2989
Table 2099 EbNoSetIdentifier (Eb/No parameter set identifier) . . . . . . . . . . . . . . 2990
Table 2100 EvamDInit (Initial phase offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2991
Table 2101 EvamNumPhaseOffset (Phase offset amount) . . . . . . . . . . . . . . . . . 2992
Table 2102 EvamTKeep (Keep time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2993
Table 2103 EvamTSweep (Sweep time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2994
Table 2104 FDPCHCodeChangeEnabled (F-DPCH code change enabled) . . . . 2995
Table 2105 FDPCHEnabled (F-DPCH enabled) . . . . . . . . . . . . . . . . . . . . . . . . . 2996
Table 2106 FDPCHSetup (F-DPCH setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2997
Table 2107 FachLoadMarginCCH (Margin for FACH load for downlink channel type
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2998
Table 2108 FachLoadThresholdCCH (Threshold for FACH load for downlink channel
type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2999
Table 2109 FastActOfTargetServCell (Faster Activation Of Target Serving Cell) 3000
Table 2110 FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . 3002
Table 2111 FastHSPAMobilityEnabled (Fast HSPA Mobility Enabled) . . . . . . . . 3003
DN00211177
Issue 12B
Id:0900d805809d7397
159
WCDMA Radio Network Configuration Parameters
Table 2112 HCS_PRIO (HCS priority level for a cell) . . . . . . . . . . . . . . . . . . . . . . 3005
Table 2113 HHoMaxAllowedBitrateDL (Maximum allowed DL user bit rate in HHO) . .
3006
Table 2114 HHoMaxAllowedBitrateUL (Maximum allowed UL user bit rate in HHO) . .
3007
Table 2115 HSCapabilityHONumbUE (HSPA Capability Based Handover Max Number of UE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3009
Table 2116 HSCapabilityHOPeriod (HSPA Capability Based Handover Period) 3010
Table 2117 HSDPA64QAMallowed (HSDPA 64 QAM allowed) . . . . . . . . . . . . . . 3011
Table 2118 HSDPA64UsersEnabled (HSDPA 64 users enabled) . . . . . . . . . . . . 3013
Table 2119 HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No) 3015
Table 2120 HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No) 3016
Table 2121 HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3017
Table 2122 HSDPAFmcgIdentifier (HSDPA FMCG identifier) . . . . . . . . . . . . . . . 3019
Table 2123 HSDPAFmciIdentifier (HSDPA FMCI identifier) . . . . . . . . . . . . . . . . . 3020
Table 2124 HSDPAFmcsIdentifier (HSDPA FMCS identifier) . . . . . . . . . . . . . . . 3021
Table 2125 HSDPALayeringCommonChEnabled (HSDPA layering for UEs in common
channels enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3022
Table 2126 HSDPAMPO (HSDPA Measurement Power Offset) . . . . . . . . . . . . . 3023
Table 2127 HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3024
Table 2128 HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3026
Table 2129 HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3027
Table 2130 HSDPAcapability (HSDPA Capability) . . . . . . . . . . . . . . . . . . . . . . . . 3029
Table 2131 HSDPAenabled (HSDPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 3030
Table 2132 HSDSCHOpState (Operational HS-DSCH state) . . . . . . . . . . . . . . . 3032
Table 2133 HSFACHActTimeToTrigger (Time to trigger for activity measurement on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3033
Table 2134 HSFACHActivityAveWin (Window size of HS-DSCH MAC-d flow of PS RB
on HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3035
Table 2135 HSFACHActivityThr (Threshold of the HS-DSCH MAC-d flow of PS RB on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3036
Table 2136 HSFACHCapability (High Speed FACH Capability) . . . . . . . . . . . . . . 3037
Table 2137 HSFACHDRXEnabled (UE DRX with High Speed Cell FACH Enabled) . .
3038
Table 2138 HSFACHEnabled (High Speed Cell_FACH DL Enabled) . . . . . . . . . 3039
Table 2139 HSFACHRABDRAEnabled (HSFACH direct resource allocation for NRT
HSPA RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3040
Table 2140 HSFACHRLCTimeToTrigger (Time to trigger for RLC measurement on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3041
Table 2141 HSFACHRel7ConSetupEC (HSFACH Rel7UE EstCause mapping in RRC
con setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3043
Table 2142 HSFACHRel8ConSetupEC (HSFACH Rel8UE EstCause mapping in RRC
con setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3045
Table 2143 HSFACHVolThrDL (DL traffic volume measurement threshold of HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3047
Table 2144 HSFACHVolThrDLPTT (DL traffic volume measurement threshold of HS-
160
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
FACH for PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3049
Table 2145 HSLoadStateHSDBRLimit (HSPA load state HSDPA bit rate limit) . 3050
Table 2146 HSLoadStateHSDOffset (HSPA load state HSDPA power Offset) . . 3051
Table 2147 HSLoadStateHSUBRLimit (HSPA load state E-DCH bit rate limit) . . 3052
Table 2148 HSLoadStateHSUOffset (HSPA load state HSUPA power Offset) . . 3053
Table 2149 HSLoadStateHSUResThr (HSPA Load State HSUPA Resource
Threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3054
Table 2150 HSPA128UsersPerCell (HSPA 128 Users per Cell) . . . . . . . . . . . . . 3055
Table 2151 HSPA72UsersPerCell (HSPA 72 Users per Cell) . . . . . . . . . . . . . . . 3057
Table 2152 HSPACapaHO (HSPA Capability Based Handover) . . . . . . . . . . . . 3059
Table 2153 HSPAFmcsIdentifier (HSPA FMCS identifier) . . . . . . . . . . . . . . . . . . 3061
Table 2154 HSPAQoSEnabled (HSPA QoS enabled) . . . . . . . . . . . . . . . . . . . . . 3062
Table 2155 HSPASCCSpecificATO (HSPA SCC Specific ATO Value) . . . . . . . . 3066
Table 2156 HSPDSCHCodeSet (HS-PDSCH code set) . . . . . . . . . . . . . . . . . . . 3067
Table 2157 HSPDSCHMarginSF128 (HS-PDSCH code upgrade margin for SF128
codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3069
Table 2158 HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay) 3071
Table 2159 HSRACHActTimeToTrigger (Time to trigger for activity measurement on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3072
Table 2160 HSRACHActivityAveWin (Window size of E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3074
Table 2161 HSRACHActivityThr (Threshold of the E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3075
Table 2162 HSRACHCapability (High Speed RACH Capability) . . . . . . . . . . . . . 3076
Table 2163 HSRACHCommonEDCHRes (Number of Common E-DCH Resources for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3077
Table 2164 HSRACHEnabled (High Speed RACH Enabled) . . . . . . . . . . . . . . . 3078
Table 2165 HSRACHExtendedAI (Use of Extended Acquisition Indicator HS-RACH)
3079
Table 2166 HSRACHImplicitRelease (Common E-DCH implicit release for HS-RACH)
3080
Table 2167 HSRACHMPO (HS-RACH Measurement Power Offset) . . . . . . . . . 3082
Table 2168 HSRACHMaxAllocTimeCCCH (Maximum E-DCH resource alloc time for
CCCH for HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3083
Table 2169 HSRACHMaxPeriodCollis (Max period for collision resolution phase for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3084
Table 2170 HSRACHMaxTotSymbolRate (Maximum total uplink symbol rate of the
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3085
Table 2171 HSRACHSubChannelNumber (Available Sub Channel Number for HSRACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3086
Table 2172 HSRACHTimeToTrigger (Traffic volume measurement time to trigger of
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3088
Table 2173 HSRACHTransmisBackOff (Additional E-DCH transmission back off for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3090
Table 2174 HSRACHVolThrUL (UL traffic volume measurement threshold of HSRACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3091
Table 2175 HSUPA16QAMAllowed (HSUPA 16QAM usage allowed in a cell) . . 3092
Table 2176 HSUPA2MSTTIEnabled (HSUPA 2 ms TTI enabled) . . . . . . . . . . . . 3093
Table 2177 HSUPAEnabled (HSUPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 3094
DN00211177
Issue 12B
Id:0900d805809d7397
161
WCDMA Radio Network Configuration Parameters
Table 2178 HSUPAUserLimit16QAM (HSUPA user limit for 16QAM usage) . . . . 3097
Table 2179 HappyBitDelayConHSRACH (Happy bit delay condition for HS-RACH) . .
3098
Table 2180 HspaMultiNrtRabSupport (HSPA multi NRT RAB Support) . . . . . . . . 3099
Table 2181 ICRCapability (ICR Capability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3100
Table 2182 IncomingLTEISHO (Incoming ISHO from LTE) . . . . . . . . . . . . . . . . . 3101
Table 2183 InitialBitRateDL (Initial bit rate in downlink) . . . . . . . . . . . . . . . . . . . . 3102
Table 2184 InitialBitRateUL (Initial bit rate in uplink) . . . . . . . . . . . . . . . . . . . . . . 3104
Table 2185 InterFreqScaleTresel (Scaling factor of Treselection in inter-frequency
case) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3105
Table 2186 InterRATScaleTresel (Scaling factor of Treselection in inter-RAT case) . .
3106
Table 2187 IntraFreq_Cell_Reselect_Ind (Intra-frequency cell re-selection indicator) .
3108
Table 2188 KforCTCH (CBS frame offset (K)) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3109
Table 2189 LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3110
Table 2190 LHOCapaReqRejRateDL (Load HO DL NRT capacity request rejection
rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3112
Table 2191 LHOCapaReqRejRateUL (Load HO UL NRT capacity request rejection
rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3114
Table 2192 LHODelayOFFCapaReqRejRate (Delay to broadcast NRT load based HO
state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3115
Table 2193 LHODelayOFFHardBlocking (Delay to broadcast hard blocking load based
HO state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3116
Table 2194 LHODelayOFFInterference (Delay to broadcast interference load based
HO state over) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3117
Table 2195 LHODelayOFFResRateSC (Delay to broadcast DL SC load based HO
state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3119
Table 2196 LHOHardBlockingBaseLoad (Load HO hard blocking base load) . . . 3120
Table 2197 LHOHardBlockingRatio (Load HO hard blocking ratio) . . . . . . . . . . . 3121
Table 2198 LHOHystTimeCapaReqRejRate (Hysteresis for NRT load measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3122
Table 2199 LHOHystTimeHardBlocking (Hysteresis for hard blocking measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3123
Table 2200 LHOHystTimeInterference (Hysteresis for interference measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3124
Table 2201 LHOHystTimeResRateSC (Hysteresis for DL SC measurement of LHO) .
3125
Table 2202 LHONRTTrafficBaseLoad (Load HO NRT traffic base load) . . . . . . . 3127
Table 2203 LHONumbUEInterFreq (Number of UEs in inter-frequency load HO ) . . .
3128
Table 2204 LHONumbUEInterRAT (Number of UEs in inter-RAT load HO ) . . . . 3129
Table 2205 LHOPwrOffsetDL (Load HO DL power offset) . . . . . . . . . . . . . . . . . . 3130
Table 2206 LHOPwrOffsetUL (Load HO UL power offset) . . . . . . . . . . . . . . . . . . 3131
Table 2207 LHOResRateSC (Load HO reservation rate of DL spreading codes) 3132
Table 2208 LHOWinSizeOFFCapaReqRejRate (Window size for NRT load measurement to stop LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3134
Table 2209 LHOWinSizeOFFHardBlocking (Window size for hard blocking measurement to stop LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3135
Table 2210 LHOWinSizeOFFInterference (Window size for interference measurement
162
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
to stop LHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3136
Table 2211 LHOWinSizeOFFResRateSC (Window size for DL SC reservation rate
measurement to stop LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3137
Table 2212 LHOWinSizeONCapaReqRejRate (Window size for NRT load measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3138
Table 2213 LHOWinSizeONHardBlocking (Window size for hard blocking measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3139
Table 2214 LHOWinSizeONInterference (Window size for interference measurement
to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3140
Table 2215 LHOWinSizeONResRateSC (Window size for DL SC reservation rate
measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3142
Table 2216 LTECellReselection (LTE Cell Reselection) . . . . . . . . . . . . . . . . . . . 3143
Table 2217 LayeringRRCConnRelTargFreq (Target frequency for layering in RRC
Connection Release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3144
Table 2218 TargetFrequency (Target frequency) . . . . . . . . . . . . . . . . . . . . . . . . 3145
Table 2219 LayeringRRCRelEnabled (Layering in RRC Connection Release Enabled)
3146
Table 2220 LcrId (Local cell resource identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 3147
Table 2221 LoadBasedCPICHEcNoSRBHSPA (Load Based CPICH EcNo for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3148
Table 2222 LoadBasedCPICHEcNoThreEDCH2MS (Load Based CPICH EcNo
Threshold for E-DCH TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3149
Table 2223 MBLBInactivityEnabled (MBLB in Inactivity Enabled) . . . . . . . . . . . . 3150
Table 2224 MBLBLoadInfoDistr (MBLB Load Information Distribution) . . . . . . . . 3151
Table 2225 MBLBMobilityEnabled (MBLB in Mobility Enabled) . . . . . . . . . . . . . 3153
Table 2226 MBLBRABSetupEnabled (MBLB in RAB Setup Enabled) . . . . . . . . 3154
Table 2227 MBLBRABSetupMultiRAB (MBLB in RAB Setup for Multi RAB) . . . 3155
Table 2228 MBLBStateTransEnabled (MBLB in State Transition Enabled) . . . . 3156
Table 2229 MEHHSDPAUserNbrCQI (HSDPA CQI user number for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3158
Table 2230 MEHHSUPAUserNbr2msTTI (HSUPA E-DCH 2 ms TTI user number for
the Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3159
Table 2231 MEHLoadStateTtT (Load state time-to-trigger for the Mass Event Handler)
3160
Table 2232 MEHMaxHSUPAUsers (Temporary max number of HSUPA users for the
Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3162
Table 2233 MEHQueueThreshold (Scheduling queue threshold for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3163
Table 2234 MEHULLHSDPAUALimit (UL load based HSDPA user amount limit for the
MEH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3165
Table 2235 MHA (MHA used) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3167
Table 2236 MIMOEnabled (MIMO Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3169
Table 2237 MIMOHSDPACapaHO (MIMO HSDPA Capability Handover) . . . . . 3171
Table 2238 MIMOWith64QAMUsage (MIMO with 64QAM usage) . . . . . . . . . . . 3172
Table 2239 MassEventHandler (Mass Event Handler functions) . . . . . . . . . . . . 3173
Table 2240 MaxBitRateDLPSNRT (Maximum downlink bit rate for PS domain NRT
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3175
Table 2241 MaxBitRateULPSNRT (Maximum uplink bit rate for PS domain NRT data)
3177
Table 2242 MaxCodeReleases (Max Code Releases) . . . . . . . . . . . . . . . . . . . . 3178
DN00211177
Issue 12B
Id:0900d805809d7397
163
WCDMA Radio Network Configuration Parameters
Table 2243 MaxDLPowerCapability (Maximum DL Power Capability) . . . . . . . . . 3179
Table 2244 MaxIncrInterferenceUL (Max increment in the received wide band
interference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3180
Table 2245 MaxNbrOfHSSCCHCodes (Maximum number of HS-SCCH codes) . 3182
Table 2246 MaxNumbHSDPAUsersS (Max number HSDPA users per MAChs/ehs
scheduler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3183
Table 2247 MaxNumbHSDSCHMACdFS (Max number HSDSCH MACd flows per
MAChs/ehs scheduler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3184
Table 2248 MaxNumberEDCHCell (Maximum number of E-DCHs in the cell) . . 3186
Table 2249 MaxNumberHSDPAUsers (Maximum number of HSDPA users) . . . 3188
Table 2250 MaxNumberHSDSCHMACdFlows (Maximum number of HS-DSCH MACd flows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3189
Table 2251 MaxNumberUECmHO (Maximum number of UEs in CM due to critical HO
measurement ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3191
Table 2252 MaxNumberUECmSLHO (Maximum number of UEs in CM due to SLHO
measurement ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3192
Table 2253 MaxNumberUEHSPACmHO (Max number of UEs in HSDPA CM due to
critical HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3194
Table 2254 MaxNumberUEHSPACmNCHO (Max number of UEs in HSDPA CM due
to NCHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3195
Table 2255 MaxTotalUplinkSymbolRate (Maximum total uplink symbol rate) . . . 3197
Table 2256 MinAllowedBitRateDL (Minimum allowed bit rate in downlink) . . . . . 3199
Table 2257 MinAllowedBitRateUL (Minimum allowed bit rate in uplink) . . . . . . . . 3201
Table 2258 MultiplePLMNListIncluded (Multiple PLMN List Included) . . . . . . . . . 3203
Table 2259 N300 (N300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3204
Table 2260 N312 (N312) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3205
Table 2261 N312Conn (N312 for connected mode) . . . . . . . . . . . . . . . . . . . . . . . 3206
Table 2262 N313 (N313) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3208
Table 2263 N315 (N315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3209
Table 2264 NASsignVolThrDL (Downlink NAS signalling volume threshold) . . . . 3211
Table 2265 NASsignVolThrUL (Uplink NAS signalling volume threshold) . . . . . . 3213
Table 2266 NCr (Maximum number of cell reselections) . . . . . . . . . . . . . . . . . . . 3214
Table 2267 NbrOfSCCPCHs (Number of SCCPCHs) . . . . . . . . . . . . . . . . . . . . . 3216
Table 2268 NforCTCH (Period of CTCH allocation (N)) . . . . . . . . . . . . . . . . . . . . 3217
Table 2269 NonHCSNcr (Maximum number of cell reselections in non-HCS case) . .
3219
Table 2270 NonHCSTcrMax (Evaluating period for amount of reselections in nonHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3220
Table 2271 NonHCSTcrMaxHyst (Hysteresis to revert from UE measurement in nonHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3222
Table 2272 NonHSEventECommMeas (Event E measurement of non HS transmitted
carrier power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3223
Table 2273 NrtFmcgIdentifier (NRT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . 3225
Table 2274 NrtFmciIdentifier (NRT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 3226
Table 2275 NrtFmcsIdentifier (NRT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . . 3227
Table 2276 NumberEDCHReservedSHOBranchAdditions (Number of E-DCHs reserved for SHO branch additions) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3228
Table 2277 OCULNRTDCHGrantedMinAllocT (DCH time limit for UL NRT DCH overload in E-DCH cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3229
164
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 2278 OCdlNrtDCHgrantedMinAllocT (Threshold for DL NRT DCH allocation time
in enhanced overload control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3231
Table 2279 OffsetToBeginCTCHBSIndex (Offset to Begin CTCH Block Set Index) . .
3232
Table 2280 PBSgrantedMinDCHallocT (PBS granted min DCH allocation time) 3233
Table 2281 PBSgrantedMinDCHallocTequalP (PBS granted min DCH allocation time
equal priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3234
Table 2282 PBSgrantedMinDCHallocThigherP (PBS granted min DCH allocation time
higher priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3235
Table 2283 PBSgrantedMinDCHallocTlowerP (PBS granted min DCH allocation time
lower priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3237
Table 2284 PCH24kbpsEnabled (Activate \ Deactivate support for 24kbps PCH) 3238
Table 2285 PFLIdentifier (PFL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3239
Table 2286 PICState (PIC state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3240
Table 2287 PI_amount (Number of PI per frame) . . . . . . . . . . . . . . . . . . . . . . . . 3241
Table 2288 PRACHDelayRange (PRACH Propagation Delay Statistics Cell Range) .
3242
Table 2289 PRACHRequiredReceivedCI (Required received C/I on PRACH at WCDMA BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3243
Table 2290 PRACHScramblingCode (PRACH scrambling code) . . . . . . . . . . . . 3244
Table 2291 PRACH_preamble_retrans (PRACH Preamble Retrans Max) . . . . . 3245
Table 2292 PSGroupId (Restriction Group Id for Packet Switched Acces) . . . . . 3246
Table 2293 PTxPICH (Transmission power of the PICH channel) . . . . . . . . . . . 3247
Table 2294 PWSMAVLimitDCHSDPA (Limit for DC HSDPA users in activation) 3249
Table 2295 PWSMAVLimitNRTHSDPA (Limit for NRT HSDPAs for Cell Activation
Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3250
Table 2296 PWSMAVLimitRTDCH (RT DCH power limit for activation) . . . . . . . 3251
Table 2297 PWSMAVLimitRTHSDPA (Limit for RT HSDPAs for Cell Activation
Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3251
Table 2298 PWSMAVPwrNRTHSDPA (NRT HSDPA power per user limit) . . . . 3252
Table 2299 PWSMAVPwrRTHSDPA (RT HSDPA power limit for activation) . . . 3253
Table 2300 PWSMCellGroup (The PWSM cell group of a cell.) . . . . . . . . . . . . . 3254
Table 2301 PWSMEXPwrLimit (Power limit for virtual AC) . . . . . . . . . . . . . . . . . 3255
Table 2302 PWSMEXUsrLimit (User limit for virtual AC) . . . . . . . . . . . . . . . . . . . 3256
Table 2303 PWSMSDLimitDCHSDPA (Limit for DC HSDPA users in shutdown) 3257
Table 2304 PWSMSDLimitNRTDCH (NRT DCH limit for shutdown) . . . . . . . . . 3258
Table 2305 PWSMSDLimitNRTHSDPA (Limit for NRT HSDPAs for Cell Shutdown
Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3259
Table 2306 PWSMSDLimitRTDCH (RT DCH limit for shutdown) . . . . . . . . . . . . 3260
Table 2307 PWSMSDLimitRTHSDPA (Limit for RT HSDPAs for Cell Shutdown
Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3261
Table 2308 PWSMSDPwrNRTHSDPA (NRT HSDPA power per user margin) . . 3262
Table 2309 PWSMSDPwrRTDCH (RT DCH Power limit for shutdown) . . . . . . . 3262
Table 2310 PWSMSDPwrRTHSDPA (RT HSDPA power limit for shutdown) . . . 3263
Table 2311 PWSMShutdownOrder (The shutdown order of cells in one PWSM cell
group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3264
Table 2312 PWSMShutdownRemCell (Shutdown of a remaining cell) . . . . . . . . 3265
Table 2313 PowerOffsetLastPreamblePRACHmessage (Power offset last preamble
and PRACH message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3266
DN00211177
Issue 12B
Id:0900d805809d7397
165
WCDMA Radio Network Configuration Parameters
Table 2314 PowerOffsetPreamHSRACH (Power Offset Last Transmitted Preamble for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3268
Table 2315 PowerOffsetSCCPCHTFCI (Power offset for S-CCPCH TFCI) . . . . . 3269
Table 2316 PO1_15 (Power offset for SCCPCH TFCI (15 ksps)) . . . . . . . . . . . . 3270
Table 2317 PO1_30 (Power offset for SCCPCH TFCI (30 ksps)) . . . . . . . . . . . . 3271
Table 2318 PO1_60 (Power offset for SCCPCH TFCI (60 ksps)) . . . . . . . . . . . . 3272
Table 2319 PowerOffsetUpdMsgSize (Power Offset Update Message Size
Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3274
Table 2320 PowerRampStepPRACHpreamble (Power ramp step on PRACH
preamble) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3275
Table 2321 PowerSaveHSPAType (HSPA Type of Cell in Power Saving Mode) 3276
Table 2322 PriScrCode (Primary downlink scrambling code) . . . . . . . . . . . . . . . . 3278
Table 2323 PrxLoadMarginDCH (Interference margin for the minimum UL DCH load)
3279
Table 2324 PrxLoadMarginEDCH (Interference margin for the minimum E-DCH load)
3281
Table 2325 PrxLoadMarginMaxDCH (Interference margin for the maximum UL DCH
load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3282
Table 2326 PrxMaxOrigTargetBTS (Max target received wide band original power for
BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3284
Table 2327 PrxMaxTargetBTS (Maximum target received wide band power for BTS)
3285
Table 2328 PrxMeasFilterCoeff (Filtering Coefficient of PrxTotal measurement) . 3286
Table 2329 PrxNoise (Uplink noise level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3288
Table 2330 PrxNoiseAutotuning (PrxNoise autotuning allowed) . . . . . . . . . . . . . 3289
Table 2331 PrxOffset (Offset for received power) . . . . . . . . . . . . . . . . . . . . . . . . 3290
Table 2332 PrxOffsetWPS (Offset for received Wireless Priority Service power) 3291
Table 2333 PrxTarget (Target for received power) . . . . . . . . . . . . . . . . . . . . . . . . 3292
Table 2334 PrxTargetMax (Maximum target for the received total wideband power) .
3293
Table 2335 PrxTargetPSMax (Max PS target in HSPA-DCH interference sharing) . . .
3295
Table 2336 PrxTargetPSMaxtHSRACH (Max PS target interference level with HSRACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3296
Table 2337 PrxTargetPSMin (Min PS target in HSPA-DCH interference sharing) 3297
Table 2338 PrxTargetPSStepDown (PS target step down in HSPA-DCH interference
sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3299
Table 2339 PrxTargetPSStepUp (PS target step up in HSPA-DCH interference
sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3300
Table 2340 PrxTotalReportPeriod (Reporting period for the RTWP measurements) . .
3301
Table 2341 PtxAICH (Transmission power of the AICH channel) . . . . . . . . . . . . 3302
Table 2342 PtxBCCHHSPDSCH (HS-PDSCH Power of HS-FACH for BCCH) . . 3303
Table 2343 PtxBCCHHSSCCH (HS-SCCH Power of HS-FACH for BCCH) . . . . 3304
Table 2344 PtxCellMax (Cell maximum transmission power) . . . . . . . . . . . . . . . . 3305
Table 2345 PtxDLabsMax (Planned maximum downlink transmission power of a radio
link) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3307
Table 2346 PtxFDPCHMax (F-DPCH maximum transmission power) . . . . . . . . . 3308
Table 2347 PtxFDPCHMin (F-DPCH minimum transmission power) . . . . . . . . . . 3309
166
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 2348 PtxHighHSDPAPwr (High threshold of PtxTotal for dynamic HSDPA pwr
alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3311
Table 2349 PtxMarginCCH (Margin for total downlink transmission power for downlink
channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3312
Table 2350 PtxMaxEHICH (The Maximum transmission power E-HICH) . . . . . . 3313
Table 2351 PtxMaxHSDPA (Maximum allowed HSDPA power) . . . . . . . . . . . . . 3314
Table 2352 PtxMeasFilterCoeff (Filtering Coefficient of PtxTotal measurement) 3315
Table 2353 PtxOffset (Offset for transmitted power) . . . . . . . . . . . . . . . . . . . . . . 3316
Table 2354 PtxOffsetEAGCH (The transmission power offset of the E-AGCH) . 3318
Table 2355 PtxOffsetEAGCHDPCCH (The power offset of the E-AGCH) . . . . . 3319
Table 2356 PtxOffsetEHICHDPCCH (The power offset of the E-HICH) . . . . . . . 3320
Table 2357 PtxOffsetERGCH (The transmission power offset of the E-RGCH) . 3322
Table 2358 PtxOffsetERGCHDPCCH (The power offset of the E-RGCH) . . . . . 3323
Table 2359 PtxOffsetExxCH2ms (The power offset of E-xxCH for 2ms TTI) . . . 3325
Table 2360 PtxOffsetExxCHSHO (The power offset of E-xxCH for SHO) . . . . . . 3326
Table 2361 PtxOffsetFDPCHSHO (The power offset of F-DPCH for SHO) . . . . 3327
Table 2362 PtxOffsetHSDPA (Offset for transmitted non-HSDPA power) . . . . . 3328
Table 2363 PtxOffsetHSSCCH (The power offset of the HS-SCCH) . . . . . . . . . 3329
Table 2364 PtxOffsetWPS (Offset for transmitted Wireless Priority Service power) . .
3330
Table 2365 PtxPSstreamAbsMax (Maximum transmitted code power of PS streaming
RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3331
Table 2366 PtxPrimaryCCPCH (Transmission power of the primary CCPCH channel)
3333
Table 2367 PtxPrimaryCPICH (Transmission power of the primary CPICH channel) .
3334
Table 2368 PtxPrimarySCH (Transmission power of the primary SCH channel) 3336
Table 2369 PtxSCCPCH1 (Tx power of S-CCPCH for PCH/FACH(s) or standalone
FACH(s)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3337
Table 2370 PtxSCCPCH2 (Tx power of S-CCPCH for Standalone PCH) . . . . . . 3339
Table 2371 PtxSCCPCH2SF128 (Tx power of S-CCPCH for Standalone PCH SF 128)
3340
Table 2372 PtxSCCPCH3 (Tx power of S-CCPCH for SAB) . . . . . . . . . . . . . . . . 3342
Table 2373 PtxSecSCH (Transmission power of the secondary SCH channel) . 3343
Table 2374 PtxTarget (Target for transmitted power) . . . . . . . . . . . . . . . . . . . . . 3344
Table 2375 PtxTargetHSDPA (Target for transmitted non-HSDPA power) . . . . . 3345
Table 2376 PtxTargetPSAdjustPeriod (DCH PS target adjust period for dyn HSDPA
pwr alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3347
Table 2377 PtxTargetPSMax (Max DCH PS target for dynamic HSDPA pwr allocation)
3348
Table 2378 PtxTargetPSMaxtHSRACH (Max PS target power level with HS-RACH)
3350
Table 2379 PtxTargetPSMin (Min DCH PS target for dynamic HSDPA pwr allocation)
3351
Table 2380 PtxTargetPSStepDown (DCH PS target step down for dynamic HSDPA
pwr alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3352
Table 2381 PtxTargetPSStepUp (DCH PS target step up for dynamic HSDPA pwr
alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3353
Table 2382 PtxTargetTotMax (Maximum value for dynamic total tx power) . . . . 3355
DN00211177
Issue 12B
Id:0900d805809d7397
167
WCDMA Radio Network Configuration Parameters
Table 2383 PtxTargetTotMin (Minimum value for dynamic total tx power) . . . . . . 3356
Table 2384 PtxThresholdCCH (Threshold for total downlink transmission power for
downlink channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3358
Table 2385 PtxTotalReportPeriod (Reporting period for the TCP measurements.) . . .
3359
Table 2386 QHCS (Quality threshold level for HCS) . . . . . . . . . . . . . . . . . . . . . . 3360
Table 2387 Qhyst1 (Cell reselection hysteresis 1) . . . . . . . . . . . . . . . . . . . . . . . . 3361
Table 2388 Qhyst1FACH (Cell reselection hysteresis 1 for FACH) . . . . . . . . . . . 3362
Table 2389 Qhyst1PCH (Cell reselection hysteresis 1 for PCH) . . . . . . . . . . . . . 3363
Table 2390 Qhyst2 (Cell reselection hysteresis 2) . . . . . . . . . . . . . . . . . . . . . . . . 3364
Table 2391 Qhyst2FACH (Cell reselection hysteresis 2 for FACH) . . . . . . . . . . . 3365
Table 2392 Qhyst2PCH (Cell reselection hysteresis 2 for PCH) . . . . . . . . . . . . . 3366
Table 2393 QqualMin (Minimum required quality level in the cell) . . . . . . . . . . . . 3367
Table 2394 QrxlevMin (Minimum required RX level in the cell) . . . . . . . . . . . . . . 3368
Table 2395 RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3369
Table 2396 RACHCapacity (RACH Capacity) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3371
Table 2397 RACHInterFreqMesQuant (RACH Inter Frequency Measurement
Quantity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3372
Table 2398 RACHIntraFreqMesQuant (RACH Intra Frequency Measurement
Quantity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3373
Table 2399 RACH_Tx_NB01max (RACH random back-off upper bound) . . . . . . 3375
Table 2400 RACH_Tx_NB01min (RACH random back-off lower bound) . . . . . . . 3376
Table 2401 RACH_tx_Max (RACH maximum number of preamble cycles) . . . . . 3378
Table 2402 RACHloadReportPeriod (Reporting period of Acknowledged PRACH
Preambles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3379
Table 2403 RACHmeasFilterCoeff (Filtering Coefficient of PRACH measurement) . . .
3380
Table 2404 RNARGroupId (Radio Network Access Regulation Function Group Id) . .
3383
Table 2405 RRCconnRepTimer1 (RRC connection setup Retransmission Timer1) . .
3384
Table 2406 RRCconnRepTimer2 (RRC connection setup Retransmission Timer2) . .
3385
Table 2407 RSEPSEventECommMeas (Event E measurement of RSEPS) . . . . 3386
Table 2408 RTWPEventECommHyst (Hysteresis time of RTWP Event E
measurements) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3387
Table 2409 RTWPEventECommMeas (Event E measurement of received total wide
band power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3388
Table 2410 RTWPMeasFilterCoeff (Filtering Coefficient of RTWP common
measurements) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3390
Table 2411 RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3392
Table 2412 RTWithHSDPAFmciIdentifier (HSDPA FMCI identifier for speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3393
Table 2413 RTWithHSDPAFmcsIdentifier (HSDPA FMCS identifier for speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3395
Table 2414 RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for speech services)
3396
Table 2415 RXBurstHSFACH (HS-FACH Reception Burst) . . . . . . . . . . . . . . . . . 3398
168
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 2416 RachLoadMarginCCH (Margin for RACH load for downlink channel type
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3399
Table 2417 RachLoadThresholdCCH (Threshold for RACH load for downlink channel
type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3400
Table 2418 RefServForCodePower (Reference service in the max code power
definition) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3401
Table 2419 RelocComm_in_InterRNC_HHO (Usage of Relocation Commit procedure
in inter RNC HHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3402
Table 2420 RsrvdSignaturesOffset (Reserved E-RGCH and E-HICH signatures per
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3403
Table 2421 RtFmcgIdentifier (RT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 3405
Table 2422 RtFmciIdentifier (RT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 3406
Table 2423 RtFmcsIdentifier (RT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 3407
Table 2424 RxDivIndicator (Rx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . 3408
Table 2425 SABEnabled (Service Area Broadcast Enabled) . . . . . . . . . . . . . . . 3409
Table 2426 SAC (Service Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3410
Table 2427 SACB (Service Area Code for SAB) . . . . . . . . . . . . . . . . . . . . . . . . . 3411
Table 2428 SHCS_RAT (Threshold for inter-RAT measurement rules in HCS) . 3413
Table 2429 SHCS_RATConn (Threshold for inter-RAT measurement for connected
mode ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3414
Table 2430 SIB4Indicator (Indicator of SIB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3415
Table 2431 SIB7factor (SIB7 expiration time factor) . . . . . . . . . . . . . . . . . . . . . . 3416
Table 2432 SIRDPCCHOffsetEDPCH (SIR target offset for DPCCH with E-DPCH) .
3417
Table 2433 SRBBitRateRRCSetupEC (SRB DCH bit rate in RRC setup based on EC)
3418
Table 2434 SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . 3419
Table 2435 SRBHSPAFmcsId (FMCS identifier for standalone SRB on HSPA) . 3420
Table 2436 SRBMapRRCSetupEC (SRB mapping in RRC setup based on EC) 3422
Table 2437 SectorID (Sector Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3423
Table 2438 ServHONumbUEInterFreq (Number of inter-frequency service HOs) 3425
Table 2439 ServHONumbUEInterRAT (Number of inter-RAT service HOs) . . . . 3426
Table 2440 ServHOPeriodInterFreq (Period to start inter-frequency service HOs) . . .
3428
Table 2441 ServHOPeriodInterRAT (Period to start inter-RAT service HOs) . . . 3429
Table 2442 ShutdownStepAmount (Shutdown step amount) . . . . . . . . . . . . . . . 3430
Table 2443 ShutdownWindow (Shutdown window) . . . . . . . . . . . . . . . . . . . . . . . 3431
Table 2444 Sintersearch (S intersearch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3432
Table 2445 SintersearchConn (S intersearch for connected mode) . . . . . . . . . . 3433
Table 2446 Sintrasearch (S intrasearch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3435
Table 2447 SintrasearchConn (S intrasearch for connected mode) . . . . . . . . . . 3436
Table 2448 Slimit_SearchRAT (S limit,SearchRAT) . . . . . . . . . . . . . . . . . . . . . . 3437
Table 2449 Slimit_SearchRATConn (S limit,SearchRAT for connected mode) . 3438
Table 2450 SmartLTELayeringEnabled (Smart LTE Layering Enabled) . . . . . . . 3439
Table 2451 SmartLTELayeringRSCP (Smart LTE Layering RSCP threshold) . . 3441
Table 2452 SmartLTELayeringTSysSel (Smart LTE Layering Target System
Selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3443
Table 2453 SmartLTELayeringUA (Smart LTE Layering NRT user amount threshold)
3444
DN00211177
Issue 12B
Id:0900d805809d7397
169
WCDMA Radio Network Configuration Parameters
Table 2454 SmartTrafVolThrDL (DL traffic volume threshold for Smartphone) . . 3445
Table 2455 SmartTrafVolThrUL (UL traffic volume threshold for Smartphone) . . 3447
Table 2456 SpeedScaleTresel (Scaling factor of Treselection for UE in high mobility)
3448
Table 2457 Sprioritysearch1 (S prioritysearch1) . . . . . . . . . . . . . . . . . . . . . . . . . . 3449
Table 2458 Sprioritysearch2 (S prioritysearch2) . . . . . . . . . . . . . . . . . . . . . . . . . . 3451
Table 2459 SsearchHCS (S searchHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3452
Table 2460 SsearchHCSConn (S searchHCS for connected mode) . . . . . . . . . . 3453
Table 2461 Ssearch_RAT (S searchRAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3454
Table 2462 Ssearch_RATConn (S searchRAT for connected mode) . . . . . . . . . 3455
Table 2463 T300 (T300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3457
Table 2464 T312 (T312) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3458
Table 2465 T312Conn (T312 for connected mode) . . . . . . . . . . . . . . . . . . . . . . . 3459
Table 2466 T313 (T313) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3460
Table 2467 T315 (T315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3461
Table 2468 T321 (High Speed Cell FACH DRX operation timer) . . . . . . . . . . . . . 3462
Table 2469 TBarred (Cell barred period) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3463
Table 2470 TCPEventECommHyst (Hysteresis time of TCP Event E measurements)
3465
Table 2471 TCPEventECommMeas (Event E measurement of transmitted carrier
power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3466
Table 2472 TCPMeasFilterCoeff (Filtering Coefficient of TCP common
measurements) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3467
Table 2473 TCrmax (Evaluating period for amount of cell reselections) . . . . . . . 3469
Table 2474 TCrmaxHyst (Hysteresis to revert from UE high-mobility measurements)
3470
Table 2475 TPCCommandERTarget (TPC command error rate target) . . . . . . . 3471
Table 2476 TargetNSEDCHToTotalEDCHPR (Target non-serving E-DCH to total EDCH power ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3473
Table 2477 Tcell (Frame timing offset of a cell) . . . . . . . . . . . . . . . . . . . . . . . . . . 3474
Table 2478 Threshservlow (Thresh serving low) . . . . . . . . . . . . . . . . . . . . . . . . . 3477
Table 2479 ToAWE_CCH (Time of Arrival Window Endpoint for common channels) .
3478
Table 2480 ToAWS_CCH (Time of Arrival Window Startpoint for common channels) .
3479
Table 2481 TrafVolThresholdDLLow (Downlink traffic volume measurement low
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3481
Table 2482 Treselection (Cell reselection triggering time) . . . . . . . . . . . . . . . . . . 3482
Table 2483 TreselectionFACH (Cell reselection triggering time for FACH) . . . . . 3483
Table 2484 TreselectionPCH (Cell reselection triggering time for PCH) . . . . . . . 3485
Table 2485 UARFCN (UTRA Absolute Radio Frequency Channel Number) . . . . 3486
Table 2486 UEDRXCapability (UE DRX in Cell_FACH capability) . . . . . . . . . . . . 3489
Table 2487 UEtxPowerMaxDPCH (Maximum UE transmission power on DPCH) 3490
Table 2488 UEtxPowerMaxPRACH (Maximum UE transmission power on PRACH) .
3491
Table 2489 UEtxPowerMaxPRACHConn (Max UE transmission power on PRACH for
connected mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3492
Table 2490 ULLoadStateHSUBRLimit (UL loaded state for HSPAusers bit rate limit) .
3494
170
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 2491 ULLoadStateHSUOffset (UL loaded state for HSPA users offset) . . 3495
Table 2492 URAId (URA identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3496
Table 2493 UTRAN_DRX_length (UTRAN DRX cycle length) . . . . . . . . . . . . . . 3497
Table 2494 UePeriodicMeasEnabled (UE Periodic Measurement Report Enabled) . .
3498
Table 2495 UseOfHCS (Use of HCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3499
Table 2496 UsersPerHSSCCHCode (Max nbr of conv users per reserved HS-SCCH
code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3500
Table 2497 VCPMaxHSDPAUsers (Temporary max number of HSDPA users for the
VCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3501
Table 2498 VCPPtxOffset (Voice Call Priority target threshold for HSDPA prevention)
3502
Table 2499 VoiceCallPriority (Voice Call Prioritisation During High Traffic Load) 3504
Table 2500 VoiceOverrideSTHSUPA (Override switch for voice services in the HSUPA
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3505
Table 2501 WACSetIdentifier (WAC Parameter Set Identifier) . . . . . . . . . . . . . . 3506
Table 2502 WCELChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 3507
Table 2503 WCELGlobalCNid (Global CN Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3508
Table 2504 WCELMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . 3510
Table 2505 WCELMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . 3510
Table 2506 WCELMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . 3511
Table 2507 WCelState (WCDMA Cell Operational State) . . . . . . . . . . . . . . . . . . 3512
Table 2508 AntBearing (Antenna Bearing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3515
Table 2509 AntHPBW (Antenna HPBW (Half Power Beam Width) for Cell) . . . . 3516
Table 2510 AntennaCoord (Antenna Coordinates) . . . . . . . . . . . . . . . . . . . . . . . 3516
Table 2511 AntennaCoordAltitudeDirect (Antenna Coordinates Altitude Direction) . .
3518
Table 2512 AntennaCoordAltitudeGround (Antenna Coordinates Altitude of Ground
Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3519
Table 2513 AntennaCoordLatitudeDegrees (Antenna Coordinates Latitude Degrees)
3520
Table 2514 AntennaCoordLatitudeFractions (Antenna Coordinates Latitude
Fractions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3521
Table 2515 AntennaCoordLatitudeMinutes (Antenna Coordinates Latitude Minutes) .
3522
Table 2516 AntennaCoordLatitudeSeconds (Antenna Coordinates Latitude Seconds)
3523
Table 2517 AntennaCoordLatitudeSign (Antenna Coordinates Latitude Sign) . . 3524
Table 2518 AntennaCoordLongitudeDegrees (Antenna Coordinates Longitude
Degrees) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3525
Table 2519 AntennaCoordLongitudeFractions (Antenna Coordinates Longitude
Fractions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3526
Table 2520 AntennaCoordLongitudeMinutes (Antenna Coordinates Longitude
Minutes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3527
Table 2521 AntennaCoordLongitudeSeconds (Antenna Coordinates Longitude
Seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3528
Table 2522 AntennaCoordLongitudeSign (Antenna Coordinates Longitude Sign) . . .
3529
Table 2523 CovType (Coverage Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3530
DN00211177
Issue 12B
Id:0900d805809d7397
171
WCDMA Radio Network Configuration Parameters
Table 2524 EnvCharact (Environment characterisation) . . . . . . . . . . . . . . . . . . . 3531
Table 2525 MaxCellBackRad (Maximum Cell back radius) . . . . . . . . . . . . . . . . . 3532
Table 2526 MaxCellRad (Maximum cell radius) . . . . . . . . . . . . . . . . . . . . . . . . . . 3533
Table 2527 RepeaterExist (Repeater exist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3534
Table 2528 WLCSEChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 3535
Table 2529 WLCSEUtranCellId (LCSE UTRAN Cell Id) . . . . . . . . . . . . . . . . . . . . 3536
Table 2530 WLCSECId (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3537
Table 2531 WLCSEMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . 3538
Table 2532 WLCSEMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . 3538
Table 2533 WLCSEMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . 3539
Table 2534 WLCSERncId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3540
Table 2535 WLCSEid (WLCSE Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3541
Table 2536 DeltaSIR (Delta SIR in the compressed mode) . . . . . . . . . . . . . . . . . 3543
Table 2537 DeltaSIRAfterDownlink (Downlink delta SIR after in the compressed
mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3544
Table 2538 DeltaSIRAfterUplink (Uplink delta SIR after in the compressed mode) . . .
3545
Table 2539 DeltaSIRDownlink (Downlink delta SIR in the compressed mode) . . 3546
Table 2540 DeltaSIRUplink (Uplink delta SIR in the compressed mode) . . . . . . . 3547
Table 2541 DownlinkOrthog (Downlink orthogonality factor) . . . . . . . . . . . . . . . . 3547
Table 2542 EDCHBLERAdjCSVoice10 (HARQ threshold for OLPC of HS CS voice ETTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3549
Table 2543 EDCHBLERAdjCSVoice2 (HARQ threshold for OLPC of HS CS voice ETTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3550
Table 2544 EDCHBLERAdjPSConvSpe10 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3551
Table 2545 EDCHBLERAdjPSConvSpe2 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3553
Table 2546 EbNoDCHOfPSNRT (Rate matching with the PS NRT DCH) . . . . . . 3554
Table 2547 EbNoDCHOfPSNRTPriQua (Primary quality target of the PS NRT DCH) .
3555
Table 2548 EbNoDCHOfPSNRTPrim (Primary Eb/N0 of the PS NRT DCH) . . . . 3556
Table 2549 EbNoDCHOfPSNRTSec (Secondary Eb/N0 of the PS NRT DCH) . . 3558
Table 2550 EbNoDCHOfPSNRTSecQua (Secondary quality target of the PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3560
Table 2551 EbNoDCHOfPSNRTSelQuaDL (Quality target selector for DL PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3561
Table 2552 EbNoDCHOfPSNRTSelQuaUL (Quality target selector for UL PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3563
Table 2553 EbNoDCHOfPSStr (Rate matching with the PS streaming DCH) . . . 3564
Table 2554 EbNoDCHOfPSStrPriQua (Primary quality target of the PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3566
Table 2555 EbNoDCHOfPSStrPrim (Primary Eb/N0 of the PS streaming DCH) . 3567
Table 2556 EbNoDCHOfPSStrSec (Secondary Eb/N0 of the PS streaming DCH) . . .
3569
Table 2557 EbNoDCHOfPSStrSecQua (Secondary quality target of the PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3571
Table 2558 EbNoDCHOfPSStrSelQuaDL (Quality target selector for DL PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3572
172
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 2559 EbNoDCHOfPSStrSelQuaUL (Quality target selector for UL PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3574
Table 2560 EbNoDCHOfSRB (Rate matching with the SRB DCH) . . . . . . . . . . . 3575
Table 2561 EbNoDCHOfSRB136 (Planned Eb/N0 of the SRB13.6 DCH) . . . . . 3576
Table 2562 EbNoDCHOfSRB136Qua (Quality target of the SRB13.6 DCH) . . . 3578
Table 2563 EbNoDCHOfSRB34 (Planned Eb/N0 of the SRB3.4 DCH) . . . . . . . 3579
Table 2564 EbNoDCHOfSRB34Qua (Quality target of the SRB3.4 DCH) . . . . . 3580
Table 2565 EbNoDCHRateGain (Data rate gain in the Eb/N0 definition) . . . . . . 3581
Table 2566 EbNoDCHRateGainCSAMR (Data rate gain for the Eb/N0 of the CS AMR)
3583
Table 2567 EbNoDCHRateGainCSData (Data rate gain for the Eb/N0 of the CS data)
3585
Table 2568 EbNoDCHRateGainPSConvSpe (Data rate gain for the Eb/N0 of the PS
conv speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3587
Table 2569 EbNoDCHRateGainPSData (Data rate gain for the Eb/N0 of the PS data
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3589
Table 2570 EbNoDCHRateGainSFDown (Data rate gain selector for the Eb/N0 of the
DL DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3591
Table 2571 EbNoDCHRateGainSFUp (Data rate gain selector for the Eb/N0 of the UL
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3592
Table 2572 EbNoDCHRateGainSRB (Data rate gain for the Eb/N0 of the SRB) 3594
Table 2573 EbNoDCHRxDiv2 (Cell offset in the UL Eb/N0, 2-way Rx diversity) . 3595
Table 2574 EbNoDCHRxDiv4 (Cell offset in the UL Eb/N0, 4-way Rx diversity) . 3597
Table 2575 EbNoDCHTxDiv (Cell offset in the DL Eb/N0 definition) . . . . . . . . . . 3598
Table 2576 EbNoEDCHCSAMR (Eb/N0 planned for the E-DCH MAC-d flow of CS
voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3599
Table 2577 EbNoEDCHOfPSStr (EbNo for E-DCH Streaming) . . . . . . . . . . . . . 3600
Table 2578 EDCHPSStr128Kbps (EbNo for E-DCH Streaming 128Kbps) . . . . . 3601
Table 2579 EDCHPSStr16Kbps (EbNo for E-DCH Streaming 16Kbps) . . . . . . . 3602
Table 2580 EDCHPSStr248Kbps (EbNo for E-DCH Streaming 248Kbps) . . . . . 3603
Table 2581 EDCHPSStr32Kbps (EbNo for E-DCH Streaming 32Kbps) . . . . . . . 3604
Table 2582 EDCHPSStr64Kbps (EbNo for E-DCH Streaming 64Kbps) . . . . . . . 3605
Table 2583 EDCHPSStr8Kbps (EbNo for E-DCH Streaming 8Kbps) . . . . . . . . . 3606
Table 2584 EDCHPSStrOver248Kbps (EbNo for E-DCH Streaming over 248Kbps) .
3607
Table 2585 EbNoEDCHPSConvSpeech (Eb/N0 planned for E-DCH PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3608
Table 2586 EbNoOfCSData (Rate matching with the CS data services) . . . . . . 3610
Table 2587 EbNoDCHOfCSDataNT (Planned Eb/N0 of the CS non transparent data)
3611
Table 2588 EbNoDCHOfCSDataNTQua (Quality target of the CS non transparent
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3613
Table 2589 EbNoDCHOfCSDataT (Planned Eb/N0 of the CS transparent data) 3614
Table 2590 EbNoDCHOfCSDataTQua (Quality target of the CS transparent data) . .
3616
Table 2591 EbNoOfCSNBAMR (Rate matching with the CS NB-AMR) . . . . . . . 3617
Table 2592 EbNoDCHOfCSNBAMR122 (Planned Eb/N0 of the CS NB-AMR 12.2) . .
3618
Table 2593 EbNoDCHOfCSNBAMR59 (Planned Eb/N0 of the CS NB-AMR 5.9) 3620
DN00211177
Issue 12B
Id:0900d805809d7397
173
WCDMA Radio Network Configuration Parameters
Table 2594 EbNoDCHOfCSNBAMRQua (Quality target of the CS NB AMR) . . . 3621
Table 2595 EbNoDCHOfCSNBAMRb (Planned Eb/N0 the CS NB-AMR subflow B) . .
3622
Table 2596 EbNoDCHOfCSNBAMRc (Planned Eb/N0 the CS NB-AMR subflow C) . .
3623
Table 2597 EbNoOfCSWBAMR (Rate matching with the CS WB-AMR) . . . . . . . 3625
Table 2598 EbNoDCHOfCSWBAMR1265 (Planned Eb/N0 of the CS WB-AMR 12.65)
3626
Table 2599 EbNoDCHOfCSWBAMRQua (Quality target of the CS WB-AMR) . . 3628
Table 2600 EbNoDCHOfCSWBAMRb (Planned Eb/N0 the CS WB-AMR subflow B) .
3629
Table 2601 EbNoOfPSConvSpe (Rate matching with the PS conversational speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3630
Table 2602 EbNoDCHOfPSConvSpe (Planned Eb/N0 of the PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3631
Table 2603 EbNoDCHOfPSConvSpeQua (Quality target of the PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3633
Table 2604 L1BLERTEDCHPSConvSpe10 (BLER target for PS Conversational
speech E-TTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3634
Table 2605 L1BLERTEDCHPSConvSpe2 (BLER target for PS Conversational speech
E-TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3635
Table 2606 L1BLERTEDCHVoice10 (BLER target for the HS CS voice E-TTI 10 ms)
3637
Table 2607 L1BLERTEDCHVoice2 (BLER target for the HS CS voice E-TTI 2 ms) . .
3638
Table 2608 SIRDPCCHInitialDCH (Initial SIR target for UL DPCCH with DPDCH) . . .
3639
Table 2609 SIRDPCCHInitialDCH128 (UL SIR target without HS-DPCCH - DPDCH SF
128) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3641
Table 2610 SIRDPCCHInitialDCH16 (UL SIR target without HS-DPCCH - DPDCH SF
16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3643
Table 2611 SIRDPCCHInitialDCH256 (UL SIR target without HS-DPCCH - DPDCH SF
256) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3644
Table 2612 SIRDPCCHInitialDCH32 (UL SIR target without HS-DPCCH - DPDCH SF
32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3645
Table 2613 SIRDPCCHInitialDCH4 (UL SIR target without HS-DPCCH - DPDCH SF
4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3646
Table 2614 SIRDPCCHInitialDCH64 (UL SIR target without HS-DPCCH - DPDCH SF
64) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3647
Table 2615 SIRDPCCHInitialDCH8 (UL SIR target without HS-DPCCH and DPDCH
SF 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3648
Table 2616 SIRDPCCHInitialDCHHS128 (UL SIR target with HS-DPCCH - DPDCH SF
128) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3650
Table 2617 SIRDPCCHInitialDCHHS16 (UL SIR target with HS-DPCCH - DPDCH SF
16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3651
Table 2618 SIRDPCCHInitialDCHHS256 (UL SIR target with HS-DPCCH - DPDCH SF
256) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3652
Table 2619 SIRDPCCHInitialDCHHS32 (UL SIR target with HS-DPCCH - DPDCH SF
32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3653
Table 2620 SIRDPCCHInitialDCHHS4 (UL SIR target with HS-DPCCH - DPDCH SF
4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3654
174
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Table 2621 SIRDPCCHInitialDCHHS64 (UL SIR target with HS-DPCCH - DPDCH SF
64) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3655
Table 2622 SIRDPCCHInitialDCHHS8 (UL SIR target with HS-DPCCH - DPDCH SF
8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3657
Table 2623 SIRDPCCHInitialDCHMax (Maximum SIR target for UL DPCCH with DPDCH only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3658
Table 2624 SIRDPCCHInitialDCHMin (Minimum SIR target for UL DPCCH with DPDCH only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3659
Table 2625 SIRDPCCHInitialDCHOffset (SIR target for UL outerloop power control
with DPDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3660
Table 2626 SIRDPCCHInitialDCHPSConvSpe (UL SIR target regardless of DL channel - PS conv speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3661
Table 2627 SIRDPCCHInitialDCHRxDiv2 (SIR target for UL DPCCH with DPDCH, 2way Rx diversity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3663
Table 2628 SIRDPCCHInitialDCHRxDiv4 (SIR target for UL DPCCH with DPDCH, 4way Rx diversity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3664
Table 2629 SIRDPCCHInitialEDCH (Initial SIR target for UL DPCCH with E-DCH) . .
3666
Table 2630 SIRDPCCHInitialEDCHPTT10MS (Initial SIR target for UL DPCCH with ETTI 10 ms - PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3667
Table 2631 SIRDPCCHInitialEDCHPTT2MS (Initial SIR target for UL DPCCH with ETTI 2 ms - PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3668
Table 2632 WRABChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 3669
Table 2633 WRABId (WRAB Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3671
Table 2634 GSMRoaming (GSM Roaming allowed) . . . . . . . . . . . . . . . . . . . . . . 3672
Table 2635 HomePLMN (Subscriber Home PLMN) . . . . . . . . . . . . . . . . . . . . . . 3672
Table 2636 HomePlmnMCC (Home PLMN Mobile Country Code) . . . . . . . . . . . 3673
Table 2637 HomePlmnMNC (Home PLMN Mobile Network Code) . . . . . . . . . . . 3674
Table 2638 HomePlmnMNCLength (Home PLMN Mobile Network Code Length) . . .
3675
Table 2639 OperatorName (Name of the subscriber home PLMN) . . . . . . . . . . . 3676
Table 2640 SubscriberGroupId (Subscriber Group Identifier) . . . . . . . . . . . . . . . 3677
Table 2641 WSGAuthorisedNetworkId (Identifier of the Authorised Network) . . 3678
Table 2642 WSGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 3679
Table 2643 CiPosCalcInSAS (Cell-ID based Position Calculation in SAS) . . . . . 3681
Table 2644 ConfAreaLevel (Confidence Area Level) . . . . . . . . . . . . . . . . . . . . . 3682
Table 2645 EmergencyShapeList (Shape Priority List for Emergency Calls) . . . 3683
Table 2646 EmArc (Arc Priority for Emergency Calls) . . . . . . . . . . . . . . . . . . . . . 3684
Table 2647 EmPoint (Point Priority for Emergency Calls) . . . . . . . . . . . . . . . . . . 3686
Table 2648 EmPointAndAlt (Point And Altitude Priority for Emergency Calls) . . 3687
Table 2649 EmPointAndCircle (Point And Circle Priority For Emergency Calls) . 3689
Table 2650 EmPointAndEll3D (3D Point And Ellipse Priority For Emergency Calls) .
3691
Table 2651 EmPointAndEllipse (Point And Ellipse Priority For Emergency Calls) 3693
Table 2652 EmPolygon (Polygon Priority for Emergency Calls) . . . . . . . . . . . . . 3695
Table 2653 LCSCapacityUsage (LCS Capacity Usage) . . . . . . . . . . . . . . . . . . . 3697
Table 2654 LCSInterfaceOption (LCS Interface option) . . . . . . . . . . . . . . . . . . . 3698
Table 2655 LCSShapeConversion (LCS Shape Conversion) . . . . . . . . . . . . . . . 3699
Table 2656 NetworkBasedAGPS (Network based A-GPS) . . . . . . . . . . . . . . . . . 3700
DN00211177
Issue 12B
Id:0900d805809d7397
175
WCDMA Radio Network Configuration Parameters
Table 2657 NetworkIndicatorForSAS (Network indicator for SAS) . . . . . . . . . . . . 3701
Table 2658 OperationalMode (SMLC Operational Mode) . . . . . . . . . . . . . . . . . . 3703
Table 2659 PartialAGPSDataDelivery (Partial A-GPS data delivery) . . . . . . . . . . 3704
Table 2660 PeriodicalReportingCapacityUsage (PeriodicalReportingCapacityUsage)
3705
Table 2661 PreferredAGPSMethod (Preferred A-GPS method) . . . . . . . . . . . . . 3706
Table 2662 RNCDelayTolRespTime (Location Reporting Delay Tolerant response
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3707
Table 2663 RNCLowDelayResponseTime (Location Reporting Low Delay Response
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3708
Table 2664 ShapeList (Shape Priority List for Non-Emergency Calls) . . . . . . . . . 3709
Table 2665 Arc (Arc Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3710
Table 2666 Point (Point Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3712
Table 2667 PointAndAlt (Point And Altitude Priority) . . . . . . . . . . . . . . . . . . . . . . 3714
Table 2668 PointAndCircle (Point And Uncertainty Circle Priority) . . . . . . . . . . . . 3715
Table 2669 PointAndEll3D (3D Point And Ellipse Priority) . . . . . . . . . . . . . . . . . . 3717
Table 2670 PointAndEllipse (Point And Uncertainty Ellipse Priority) . . . . . . . . . . 3719
Table 2671 Polygon (Polygon Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3721
Table 2672 SignallingPointCodeOfSAS (Signalling Point Code of SAS) . . . . . . . 3723
Table 2673 UEBasedAGPS (UE based A-GPS) . . . . . . . . . . . . . . . . . . . . . . . . . 3724
Table 2674 WSMLCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 3725
Table 2675 WSMLCid (WSMLC Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3726
176
Id:0900d805809d7397
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Summary of changes
1 Summary of changes
Changes between document issues are cumulative. Therefore, the latest document
issue contains all changes made to previous issues..
Changes between Issue 12A (2013-03-15, RU40) and Issue 12B (2013-06-13,
RU40).
1.1
New Parameters in RNC RN7.0
1.1.1
ADJD
1.1.1.1
AdjdSRBHopsId (SRB HOPS Identifier)
Description
This parameter identifies the parameter set (HOPS object) which controls the intrafrequency handover to the additional neighbor cell when a user has standalone
SRB allocated on DCH or on HSPA.
If the value of this parameter is "Not defined" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled", then:
- the ADJD parameter AdjdRTHopsId identifies the HOPS parameter set when
the standalone SRB is allocated on DCH, and
- the ADJD parameter AdjdHSDPAHopsId identifies the HOPS parameter set
when the standalone SRB is allocated on HSPA.
Related features
Soft Handover Based on Detected Set Reporting (optional) AND Fast HSPA
Mobility (optional)
1.1.2
1.1.2.1
ADJS
SRBHopsIdentifier (SRB HOPS Identifier)
Description
This parameter identifies the parameter set (HOPS object) controlling the intra-frequency handovers of a user having standalone SRB allocated on DCH or on HSPA.
If the value of this parameter is "Not defined" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled", the ADJS parameter RtHopsIdentifier
identifies the HOPS parameter set when the standalone SRB is allocated on DCH,
and the ADJS parameter HSDPAHopsIdentifier identifies the HOPS parameter set
when the standalone SRB is allocated on HSPA.
Related features
Fast HSPA Mobility (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
177
Summary of changes
1.1.3
1.1.3.1
WCDMA Radio Network Configuration Parameters
CBCI
ETWSsupportEnabled (ETWS Support Enabled)
Description
This parameter enables/disables ETWS Support feature for the CBC.
DRX cycle length parameters CNDRXLength and UTRAN_DRX_length shall
be less than 4000ms for enabling ETWS support functionality in RNC.
Related features
( Service Area Broadcast (optional) OR SAB Support with 2 SCCPCHs (optional)
) AND 3GPP Rel8 CBS ETWS support (optional)
1.1.3.2
IUOIdentifier (IUO Object Identifier)
Description
The IUO identification gives the reference to the IUO object used for the CBCI. The
IUO object contains Iu Operator information.
Related features
Service Area Broadcast (optional) OR SAB Support with 2 SCCPCHs (optional)
1.1.4
1.1.4.1
Description
COSITE
COSITEChangeOrigin (COSITE Change origin)
This parameter defines the origin of the last configuration action affecting the object.
1.1.4.2
COSITEId (COSITE Identifier)
Description
This parameter uniquely identifies the COSITE object.
Related features
RNC co-siting (standard)
1.1.4.3
SharingState (Sharing State)
Description
Identifies the role of the Controller in Co-site configuration. For example, Co-site
Master or Co-site Resource.
Co-site Master is the RNC containing the configuration of the shared Radio
Network.
Co-site Resource is the RNC providing the additional resources for the Radio
Network managed by the Co-site Master.
Related features
RNC co-siting (standard)
178
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.5
1.1.5.1
Summary of changes
COSRNC
AdditionalStateInfo (Additional State Information)
Description
This parameter provides additional information in case the Availability Status is
Failed or Degraded. It also provides information when the initialization of co-siting
functionality is ongoing and when the initialization is complete.
If Availability Status is Degraded then this parameter identifies whether its due
to "O&M I/F Failure" or "OMS connection mismatch".
Related features
RNC co-siting (standard)
1.1.5.2
AdminStateInfo (Admin State Info)
Description
This parameter provides information about the status of the COSRNC administrative state modification operation initiated by the operator.
Note! Deletion of COSRNC object shall not be allowed in case COSRNCAdministrativeState is other than Locked or value of COSRNC-AdminStateInfo is
Operation Ongoing (1).
Related features
RNC co-siting (standard)
1.1.5.3
AdministrativeState (Administrative State)
Description
This parameter provides the Administrative control of the co-siting functionality.
User can decide when to take the co-siting functionality into use (locked->unlocked)
or vice-versa (unlocked->locked). ShuttingDown is meant to gracefully terminate
the co-siting.
Note! AdministrativeState transition from Locked to ShuttingDown is not
allowed.
Note! While COSRNC object creation AdministrativeState is not allowed to have
ShuttingDown as the initial value, it could only be Locked or Unlocked.
Note! Deletion of COSRNC object shall not be allowed in case COSRNCAdministrativeState is other than Locked or value of COSRNC-AdminStateInfo is
Operation Ongoing (1).
Related features
RNC co-siting (standard)
DN00211177
Issue 12B
Id:0900d805809da32a
179
Summary of changes
1.1.5.4
WCDMA Radio Network Configuration Parameters
AvailabilityStatus (Availability Status)
Description
This parameter indicates the current availability status of the resources needed for
co-siting functionality.
- <empty>
Resources are ready without any restrictions. OperationalState
is Enabled.
- Off-line
Resources need routine initialization before they could be
ready. OperationalState is Disabled.
- Failed
Resources cannot work due to some error (for example,
cluster I/F failure). OperationalState is Disabled.
- Degraded
Resource are ready but with some restrictions. RNC-RNC
BTS O&M I/F may not be available or RNCs might be connected to different
OMSes. OperationalState is Enabled.
If, Availability Status is Offline or Failed then Operational State can only have
"Disabled" as valid value.
If , Availability Status is 0 or Degraded then Operational State can only have
"Enabled" as valid value.
Related features
RNC co-siting (standard)
1.1.5.5
ClusterIfState (Cluster Interface State)
Description
This field indicates the state of the interface between RNCs in RNC cluster as visible
on co-site Master RNC. It shall have three possible values Enabled (1), Disabled (0)
and Not Known (255).
Related features
RNC co-siting (standard)
1.1.5.6
Description
COSRNCChangeOrigin (COSRNC Change origin)
This parameter defines the origin of the last configuration action affecting the object.
1.1.5.7
COSRNCId (COSRNC Identifier)
Description
This parameter contains the RNCId of the other RNC in the Co-siting. For example,
in an cRNC-mcRNC co-siting pair, the mcRNC's COSRNCId shall contain the
RNCId of the cRNC and vice-versa.
Related features
RNC co-siting (standard)
180
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.5.8
Summary of changes
OperationalState (Operational State )
Description
This field indicates whether the system is capable of Co-siting or not. Co-siting functionality shall work if the Operational State is Enabled and the Administrative State
is Unlocked.
If, Operational State is Enabled then Availability Status could have only these
values: <Empty>(0) or Degraded.
If, Operational State is Disabled then Availability Status could have only these
values: Offline or Failed
Related features
RNC co-siting (standard)
1.1.5.9
PeerRNCIPAddress (Peer RNC IP Address)
Description
This is the O&M IP Address of the counterpart RNC in Co-site configuration. The
RNC in Co-site Resource role shall attempt RNC-RNC O&M I/F connection at this
IP Address. The value has to be set by the operator in the Co-site Resource only
and the value is updated automatically by the Co-site Master upon successful
establishment of the RNC-RNC O&M I/F. The value in Co-site Master indicates the
IP Address of the Co-site Resource.
Related features
RNC co-siting (standard)
1.1.5.10
RNCOMConnState (RNC-RNC O&M Connection State)
Description
This field indicates the state of the RNC-RNC O&M connection as visible on co-site
Master RNC. It can have three possible values Enabled (1), Disabled (0) and Not
Known (255).
Related features
RNC co-siting (standard)
1.1.6
1.1.6.1
Description
DN00211177
Issue 12B
IUCS
CNId (Core Network Identity)
This parameter describes the Core Network Identity of the CN connected to the Iu
interface.
Id:0900d805809da32a
181
Summary of changes
1.1.6.2
WCDMA Radio Network Configuration Parameters
CSFlexiIuWeight (CS Flexible Iu Weight)
Description
This parameter defines weight value of each CS CN node (Iu interface) for Flexible
Iu feature load sharing. FlexiIuWeight is used for the weighted round robin method
to select a CN node to balance the load between the available CN nodes. Load
sharing of Iu nodes is defined by configuring FlexiIuWeight of the interface.
The weight value used in load sharing decision is weight value of CN node
divided by sum of all weight values of CN nodes for the domain of one operator.
User divides weights among all CN nodes of the domain/operator for example
like this:
MSS1 60
MSS2 50
MSS3 40
Thus the actual weight value used in load sharing calculation for e.g. MSS1
would be individual weigh value divided by sum of weight values,
60/(60+50+40)=0.4
If the weight value is identical for all CN nodes, it means that the equal load is
shared among all CN nodes. If the weight value is default value (0) for this node, it
means that this node is not used for load sharing.
Related features
Flexible Iu (optional)
1.1.6.3
Description
The IUO identification gives the reference to the IUO object used for the IUCS. The
IUO object contains Iu Operator information
1.1.7
1.1.7.1
Description
182
IUOIdentifier (IUO Object Identifier)
IUO
CSCNDRXLength (CN CS domain specific DRX cycle length)
The DRX cycle length is used for the CN domain to count paging occasions for discontinuous reception. This parameter is given separately for the CS domain and the
PS domain.
(The duration of the DRX cycle is 2 <power> k frames, where "k" is the used
DRX cycle length coefficient for CN.)
This parameter is part of System Information Block 1.
As per 3GPP the UE may be attached to different CN domains with different
CN domain specific DRX cycle lengths. The UE shall store each CN domain specific
DRX cycle length for each CN domain the UE is attached to and use the shortest of
those DRX cycle lengths.
In-case of MOCN all operators must define the same value of DRX cycle length
and in case of either MORAN (without MOCN at the same time) or MORAN with
Flex IU, DRX cycle length can be operator specific parameter.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.7.2
Description
Summary of changes
PSCNDRXLength (CN PS domain specific DRX cycle length)
The DRX cycle length is used for the CN domain to count paging occasions for discontinuous reception. This parameter is given separately for the CS domain and the
PS domain.
(The duration of the DRX cycle is 2 <power> k frames, where "k" is the used
DRX cycle length coefficient for CN.)
This parameter is part of System Information Block 1.
The UE shall store each CN domain specific DRX cycle length for each CN
domain the UE is attached to and use the shortest of those DRX cycle lengths.
In-case of MOCN all operators must define the same value of DRX cycle length
and in case of either MORAN (without MOCN at the same time) or MORAN with
Flex IU, DRX cycle length can be operator specific parameter.
1.1.7.3
IuBarringRecoveryTimerCS (Iu service barring recovery timer for
CS)
Description
The parameter defines the timer to phase the system information message sending
after IuCS link recovery. When an IuCS link fails, the related CN service is barred
by sending the system information messages to the UEs without the failed service
CN domain. When the failed link is recovered, the system information messages are
sent again with the recovered service CN domain information. The system information sending is phased according to the given parameter to avoid the high load of
the simultaneous network access attempts by the UEs.
Related features
RNC license control for Iu link break protection (optional)
1.1.7.4
IuBarringRecoveryTimerPS (Iu service barring recovery timer for
PS)
Description
The parameter defines the timer to phase the system information message sending
after IuPS link recovery. When an IuPS link fails, the related CN service is barred
by sending the system information messages to the UEs without the failed service
CN domain. When the failed link is recovered, the system information messages are
sent again with the recovered service CN domain information. The system information sending is phased according to the given parameter to avoid the high load of
the simultaneous network access attempts by the UEs.
Related features
RNC license control for Iu link break protection (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
183
Summary of changes
1.1.7.5
WCDMA Radio Network Configuration Parameters
IubTransportSharingInd (Iub Transport Sharing index)
Description
With Iub Transport Solution for Network Sharing feature operator may define PLMN
id specific transport resource and transport priority allocation. PLMN id specific
transport resource index within the IUO instance refers to WBTS object IP Based
Route and TQM identifiers in the following manner:
IUO - IubTransportSharingInd
- Enum value 0: Feature disabled for the PLMN id / Operator
- Enum value 1: WBTS - IPBasedRouteId or TQMId
- Enum value 2: WBTS - IPBasedRouteId2 or TQMId2
- Enum value 3: WBTS - IPBasedRouteId3 or TQMId3
- Enum value 4: WBTS - IPBasedRouteId4 or TQMId4
Example: For the PLMN id x within IUO instance y enum value 2 has been set.
For the user plane transport bearer setup having the matching PLMN id allocation
system chooses IP Based Route id reference from the WBTS - IPBasedRouteId2
attribute. Similarly TQMId2 will be selected if the Iub Transport QoS feature is configured. Thus the given IP Based Route definition is used for the PLMN x related call
setups.
Note: The first IP Based Route identifier (WBTS - IPBasedRouteId) or TQM
object identifier (WBTS - TQMId) is selected for the setup when the PLMN id is not
known or when the referred IP Based Route attribute is has unspecified value. The
PLMN id is not known with MOCN feature within the initial RRC connection setup
when the RAB has not been established yet.
Related features
Multi-Operator Core Network (optional) OR Multioperator RAN (optional)
1.1.8
1.1.8.1
Description
184
CNId (Core Network Identity)
This parameter describes the Core Network Identity of the CN connected to the Iu
interface.
1.1.8.2
Description
IUPS
IUOIdentifier (IUO Object Identifier)
The IUO identification gives the reference to the IUO object used for the IUPS. The
IUO object contains Iu Operator information.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.8.3
Summary of changes
PSFlexiIuWeight (PS Flexible Iu Weight)
Description
This parameter defines weight value of each PS CN node (Iu interface) for Flexible
Iu feature load sharing. FlexiIuWeight is used for the weighted round robin method
to select a CN node to balance the load between the available CN nodes. Load
sharing of Iu nodes is defined by configuring FlexiIuWeight of the interface.
The weight value used in load sharing decision is weight value of CN node
divided by sum of all weight values of CN nodes for the domain of one operator.
User divides weights among all CN nodes of the domain/operator for example
like this:
SGSN1 60
SGSN2 50
SGSN3 40
Thus the actual weight value used in load sharing calculation for e.g. SGSN1
would be individual weigh value divided by sum of weight values,
60/(60+50+40)=0.4
If the weight value is identical for all CN nodes, it means that the equal load is
shared among all CN nodes. If the weight value is default value (0) for this node, it
means that this node is not used for load sharing.
Related features
Flexible Iu (optional)
1.1.9
1.1.9.1
IUR
AppAwareRANEnabled (Application Aware RAN Enabled)
Description
This parameter defines whether the feature Application Aware RAN is enabled or
not in the corresponding Drift RNC.This parameter value is checked only when the
serving HSDPA/HSPA cell is under Drift RNC.
Dynamic service or application prioritization for the HSDPA scheduling is
applied over Iur towards a corresponding Drift RNC if this parameter value is set to
‘Enabled’.
By enabling this parameter it is interpretive so that all BTSs under the Drift RNC
are supporting RAN2509 feature. This parameter does not have any affect in the
drifting RNC.
Related features
Application Aware RAN (optional)
1.1.9.2
Description
DN00211177
Issue 12B
MaxFPDLFrameSizeIur (Maximum FP downlink frame size Iur)
The user plane frame size can be limited with this parameter in order to avoid IP
layer fragmentation. The RNC takes the value into account in DL User Plane traffic
processing and limits the maximum HS-DSCH FP frame size accordingly. The
value has to be planned according to the minimum IP layer MTU along the path to
the DRNC and BTS. The parameter is applied in SRNC to both ATM and IP Iur interfaces.
The IP and UDP header overheads have to be subtracted from the IP interface
MTU value (e.g. IPv4 IP header 20 bytes, UDP header 8 bytes) when adjusting the
value since the parameter directly controls the user plane FP frame size.
Id:0900d805809da32a
185
Summary of changes
Related features
1.1.10
1.1.10.1
WCDMA Radio Network Configuration Parameters
IP Based Iur (optional) OR HSPA Inter-RNC Cell Change (optional)
PFL
PFLDBHSDAMR (Preferred Frequency Layer for DB-DC-HSDPA
AMR)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has only an AMR RAB allocated. (CS RABs other than AMR use the same parameter as AMR.)
Child parameters
•
Related features
Multi-Band Load Balancing (optional)
1.1.10.2
PrefLayerDBHSDAMR
PFLDBHSDAMRNRT (Preferred Frequency Layer for DB-DC-HSDPA
AMR and NRT)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has an AMR RAB, 0...1 streaming RAB, and 1...3 NRT RAB(s) allocated. (CS RABs
other than AMR use the same parameter as AMR.)
Child parameters
•
Related features
Multi-Band Load Balancing (optional)
1.1.10.3
PrefLayerDBHSDAMRNRT
PFLDBHSDNRT (Preferred Frequency Layer for DB-DC-HSDPA
NRT)
Description
This parameter defines the preferred layers for DB-DC-HSDPA capable UE that has
only NRT RAB(s) allocated.
Child parameters
•
Related features
Multi-Band Load Balancing (optional)
1.1.10.4
PrefLayerDBHSDNRT
PFLDBHSDStr (Preferred Frequency Layer for DB-DC-HSDPA
Streaming)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has a streaming RAB and 0...3 NRT RAB(s) allocated.
Child parameters
•
Related features
Multi-Band Load Balancing (optional)
186
PrefLayerDBHSDStr
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.10.5
Summary of changes
PFLDBHSDAMR/PrefLayerDBHSDAMR (Preferred Layer for DB-DCHSDPA AMR)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has only an AMR RAB allocated. (CS RABs other than AMR use the same parameter as AMR.)
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency of the preferred cell. Up to eight different preferred layers
can be defined.
Parent parameter
PFLDBHSDAMR
Related features
Multi-Band Load Balancing (optional)
1.1.10.6
PFLDBHSDAMRNRT/PrefLayerDBHSDAMRNRT (Preferred Layer
for DB-DC-HSDPA AMR and NRT)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has an AMR RAB, 0...1 streaming RAB, and 1...3 NRT RAB(s) allocated. (CS RABs
other than AMR use the same parameter as AMR.)
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency of the preferred cell. Up to eight different preferred layers
can be defined.
Parent parameter
PFLDBHSDAMRNRT
Related features
Multi-Band Load Balancing (optional)
1.1.10.7
PFLDBHSDNRT/PrefLayerDBHSDNRT (Preferred Layer for DB-DCHSDPA NRT)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has only NRT RAB(s) allocated.
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency of the preferred cell. Up to eight different preferred layers
can be defined.
Parent parameter
PFLDBHSDNRT
Related features
Multi-Band Load Balancing (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
187
Summary of changes
1.1.10.8
WCDMA Radio Network Configuration Parameters
PFLDBHSDStr/PrefLayerDBHSDStr (Preferred Layer for DB-DCHSDPA Streaming)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has a streaming RAB and 0...3 NRT RAB(s) allocated.
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency of the preferred cell. Up to eight different preferred layers
can be defined.
Parent parameter
PFLDBHSDStr
Related features
Multi-Band Load Balancing (optional)
1.1.11
1.1.11.1
RNAC
RNARDSACGuardTime (Access class restriction guard time)
Description
This parameter defines the guard time for the state transitions with RNAR and
DSAC features. If timer is running then the original state transition is done.
If the minimum value is used, timer is not used and state transitions can be
done. This causes extra signalling because UE can activate immediately again.
Related features
Radio Network Access Regulation Function (optional)
1.1.11.2
RNARDSACCell_DCH (Access class restriction level for Cell_DCH)
Description
This parameter defines the threshold of access class restriction level. If the access
class restriction level goes above the threshold, whenever UE becomes inactive
RNC does not transfer UE to Cell_FACH or Cell/URA_PCH but releases the UE to
the idle if the following is true:
- the last digit of the IMSI of the UE matches the restricted access class and
RNARDSACGuardTimer is not running.
If the minimum parameter value is used, UE's can be moved to IDLE with low
access class restriction level. If the maximum parameter value is used UE can be
moved to IDLE only when the all access classes are restricted.
The functionality is applied in cells as enabled with CMOB-TrafficRestriction.
Related features
Radio Network Access Regulation Function (optional)
188
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.11.3
Summary of changes
RNARDSACCell_PCH (Access class restriction level for Cell_PCH)
Description
This parameter defines the threshold of access class restriction level. If the access
class restriction level goes above the threshold, whenever UE becomes active in
Cell/URA_PCH, RNC does not move UE to Cell_FACH/DCH if the following is true:
- the last digit of the IMSI of the UE matches the restricted access class and
RNARDSACGuardTimer is not running.
If the minimum parameter value is used, UE's is not moved to Cell_FACH/DCH
with low access class restriction level. If the maximum parameter value is used UE
will not be moved to Cell_FACH/DCH when the all access classes are restricted.
The functionality is applied in cells as enabled with CMOB-TrafficRestriction.
Related features
Radio Network Access Regulation Function (optional)
1.1.11.4
AutoACRestForCellPCH (Access Restriction for Cell_PCH state UE)
Description
This parameter defines the threshold of access class restriction level. If the access
class restriction level goes above the threshold, when ever UE becomes inactive
RNC does not transfer UE to Cell_FACH or Cell/URA_PCH but releases the UE to
the idle if the following is true:
- the last digit of the IMSI of the UE matches the restricted access class in the
current and in the following restriction step
If the minimum parameter value is used UE's will be permitted to do the RRC
connection after the release sooner than if the maximum value is used.
Related features
Automatic access class restriction (optional)
1.1.11.5
AutoACDecRestHysNRTQ (Automatic Access Class Decrease
Restriction Level Hysteresis for NRT queue length trigger)
Description
This parameter defines the time period during which the averaged length of the NRT
scheduling queue must be continuously lesser than the threshold value to indicate
AC restriction level to be decreased.
Related features
Automatic access class restriction (optional)
1.1.11.6
AutoACDecRestHysRTWP (Automatic Access Class Decrease
Restriction Level Hysteresis for Received Total Wideband Power
trigg)
Description
This parameter defines the time period during which the UL load of the cell due to
total received wideband power must be continuously less than the threshold value
to indicate AC restriction level to be decreased.
Related features
Automatic access class restriction (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
189
Summary of changes
1.1.11.7
WCDMA Radio Network Configuration Parameters
AutoACIncRestHysNRTQ (Automatic Access Class Increase
Restriction Level Hysteresis for NRT queue length trigger)
Description
This parameter defines the time period during which the average length of the NRT
scheduling queue continuously exceeded the threshold value, indicating that AC
restriction level needs to be increased.
Related features
Automatic access class restriction (optional)
1.1.11.8
AutoACIncRestHysRTWP (Automatic Access Class Increase
Restriction Level Hysteresis for Received Total Wideband Powertrigge)
Description
This parameter defines the time period during which the UL cell load, because of
the total received wide band power, must be continuously greater than the threshold
value to indicate that AC restriction level needs to be increased.
Related features
Automatic access class restriction (optional)
1.1.11.9
AutoACMaxRestLevel (Automatic Access Class Maximum Restriction Level)
Description
This parameter defines the maximum number of Access Classes (AC0, AC1, ...,
AC9) that are restricted in a cell at the same time.
- 10% indicates that one Access Class is barred in a cell
- 20% indicates that two ACs are barred at the same time
...
- 90% indicates that nine ACs are barred at the same time
Note: All ACs shall not be barred. Maximum restriction level shall be used 90%.
Related features
Automatic access class restriction (optional)
1.1.11.10
AutoACRLevelUpdInt (Automatic Access Class Restriction Level
Update Interval)
Description
The parameter defines the time interval how often the access class restriction level
can updated in System Information broadcast SIB3 during automatic access class
restriction. The trigger for the automatic access class restriction is CN overload,
RNC overload or Cell specific UL overload. If the minimum value is configured, the
automatic access class restriction level is updated frequently. If the maximum value
is configured the automatic access class restriction level is updated very rarely.
Ideally the value of AutoACRLevelUpdInt is half of the value of the RNC-RestrictionInterval.
Related features
Automatic access class restriction (optional)
190
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.11.11
Summary of changes
AutoACRTrigRNCLoad (Automatic Access Class Restriction
Trigger of RNC Load)
Description
This parameter defines the threshold for the RNC average unit load to start access
class restriction procedure in Radio Network Controller. The RNC average unit load
is determined by the S-RNTI allocation failure rate in the UE traffic handling units of
the Radio Network Controller. The Trigger starts the automatic access class restriction procedure in all of the cells in Radio Network Controller. The Minimum value
triggers the Automatic Access Class Restriction procedure in a minor RNC overload
situation. The Maximum value starts the Automatic Access Class Restriction procedure only in a very severe RNC overload.
Related features
Automatic access class restriction (optional)
1.1.11.12
DynHSUPABLERThrBurstyTP (Bursty Data throughput threshold
per TTI)
Description
This parameter defines the throughput threshold in number of FP frames per TTI
(10ms). It is used by the outer loop power control of the RNC to check the bursty
data rate condition for Dynamic HSUPA BLER. In case of 2ms TTI, this same
parameter is used with multiple of 5.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
1.1.11.13
DynHSUPABurstyPeriod (Bursty Period for Dyn HSUPA BLER)
Description
This parameter defines minimum period which the BLER state must be bursty
before outer loop power control state can be changed from the bursty BLER state
to continuous BLER state, or from peak or continuous BLER state to bursty BLER
state. It is allowed to change BLER state from bursty or continuous BLER state to
the peak BLER state without waiting for the expiration of the timer set by the parameter DynHSUPABurstyPeriod. Change from peak BLER state to bursty or continuous BLER state is performed if throughput falls below
DynHSUPABLERMaxRateThrB or DynHSUPABLERMaxRateThrC10/
DynHSUPABLERMaxRateThrC2, correspondingly and condition has been valid
time defined with the parameter DynHSUPABurstyPeriod.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
191
Summary of changes
1.1.11.14
WCDMA Radio Network Configuration Parameters
ULFastOLPCDTXthld (DTX threshold for uplink faster outer loop)
Description
This parameter determines the maximum length of the DTX period. During the DTX
period the in-active UL OLPC entity is not allowed to transmit the SIR target modification commands. In case, the controlled bearer has been in DTX for more than
DTX period value and being activated (data available on the Transport Channel),
the UL outer loop PC Entity is allowed to send SIR Target up modification command
to the UL outer loop PC controller.
0 : DTX period value defined as internal constant (200 ms)
1 : DTX period is fixed as zero so that all OLPC entities are always at least
semi-active state and able to send SIR target increase command anytime
The value of this parameter is used, if RNFC-FasterOLPCEnabled parameter
is set to Enabled. Short descriptionThis Parameter determines the maximum
length of the DTX period that does not affect the functionality of the faster UL outer
loop PC.
Related features
Faster OLPC (standard)
1.1.11.15
FOLPCSIRTgtModInt (Faster OLPC SIR target modification interval)
Description
This parameter defines the minimum interval between two SIR target modification
commands sent by OLPC entity of UL NRT return channel over the DMPG-DMPG
interface.
The value of this parameter is used, if RNFC-FasterOLPCEnabled parameter
is set to Enabled. Otherwise, RNC internal constant value 500 ms is used.
If the minimum value of parameter is used, OLPC entity sends SIR modification
command more frequently than if the maximum value is used. Short description
This parameter defines the minimum interval between two SIR target modification
commands sent by OLPC entity of UL NRT return channel over the DMPG-DMPG
interface.
Related features
Faster OLPC (standard)
1.1.11.16
FOLPCStepSizSIRTgt (Faster OLPC step size of SIR target changes)
Description
This Parameter defines the minimum step size of the SIR target modification a PC
Entity of UL NRT return channel can request in case Faster OLPC is enabled.
The value of this parameter is used, if RNFC-FasterOLPCEnabled parameter
is set to Enabled. Otherwise, RNC internal constant value 0.3 dB is used.
If the minimum value of parameter is used, OLPC adjust SIR target more frequently in smaller steps than if the maximum value is used. Short descriptionThis
Parameter defines the minimum step size of the SIR target modification a PC Entity
of UL NRT return channel can request in case Faster OLPC is enabled.
Related features
Faster OLPC (standard)
192
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.11.17
Summary of changes
L1BurstDataBLERTrgtEDCH (Layer1 Bursty Data BLER target for EDCH)
Description
This parameter defines L1 BLER target for the E-DCH MAC-d flow of PS NRT
service. It is used by the outer loop power control of the RNC for bursty data.
Value of the parameter equals to the log10 of the BLER value.
10^-1 = 0.1 i.e. BLER target is 10%.
Note: BLER target defined by this parameter is used after number of retransmission defined by parameter “Retransmissions in Dyn HSUPA BLER for Bursty
Data”.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
1.1.11.18
L1ContBLERTrgtEDCH10 (Layer1 Continuous BLER target for EDCH TTI 10 ms)
Description
This parameter defines L1 BLER target for the E-DCH MAC-d flow of PS NRT
service when TTI = 10 ms. It is used by the outer loop power control of the RNC for
continuous transmission that provides better throughput and coverage.
Value of the parameter equals to the log10 of the BLER value.
10^-0.7 = 0.199 i.e. BLER target is 20%.
High BLER values increase latency due to HARQ retransmissions in L1, especially this is valid when E-DCH TTI = 10 ms is used.
Note: BLER target defined by this parameter is used after number of retransmission defined by parameter “Retransmissions in Dyn HSUPA BLER for Cont Data
10 ms TTI”.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
1.1.11.19
L1ContBLERTrgtEDCH2 (Layer1 Continuous BLER target for E-DCH
TTI 2 ms)
Description
This parameter defines L1 BLER target for the E-DCH MAC-d flow of PS NRT
service when TTI = 2 ms. It is used by the outer loop power control of the RNC for
continuous transmission that provides better throughput and coverage.
Value of the parameter equals to the log10 of the BLER value.
10^-1 = 0.1 i.e. BLER target is 10%.
High BLER values increase latency due to HARQ retransmissions in L1. When
E-DCH TTI = 2 ms is used latency increase is however small because HARQ period
is 16 ms.
Note: BLER target defined by this parameter is used after number of retransmission defined by parameter “Retransmissions in Dyn HSUPA BLER for Cont Data
2 ms TTI”.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
193
Summary of changes
WCDMA Radio Network Configuration Parameters
1.1.11.20
L1PeakRateBLERTrgtEDCH (Layer1 Peak Data Rate BLER target for
E-DCH)
Description
This parameter defines the L1 BLER target for the E-DCH MAC-d flow of PS NRT
service. It is used by the outer loop power control of the RNC for peak data rate.
The value of the parameter is equals to the log10 of the BLER value.
Examples:
10^-2 = 0.01 i.e. BLER target is 1%.
10^-1.3 = 0.05 i.e. BLER target is 5%.
Note: The BLER target that is defined by this parameter is used after the number
of retransmission defined by the parameter “Retransmissions in Dyn HSUPA BLER
for Peak data”.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
1.1.11.21
PagingRestrictionInd (Paging Restriction Indication for PPAC)
Description
The parameter defines the paging response restriction per CN domain. Valid when
RNFC - PPACEnabled parameter is enabled.
Related features
Paging Permission with Access Control (standard)
1.1.11.22
DynHSUPABLERMaxRateThrC10 (Peak rate thr for cont data of Dyn
HSUPA BLER 10 ms TTI )
Description
This parameter defines the peak rate threshold in relation to the UE's maximum
data rate when E-DCH TTI is equivalent to 10 ms. This parameter is used by the
dynamic HSUPA BLER algorithm. The outer loop power control of the RNC applies
the parameter when UE is currently using continuous data. If the current throughput
exceeds the value of the parameter, then OLPC is configured to use the peak data
rate configuration.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
1.1.11.23
DynHSUPABLERMaxRateThrC2 (Peak rate thr for cont data of Dyn
HSUPA BLER 2 ms TTI)
Description
This parameter defines the peak rate threshold in relation to the UE's maximum
data rate when E-DCH TTI is equivalent to 2 ms. This parameter is used by the
dynamic HSUPA BLER algorithm. The outer loop power control of the RNC applies
the parameter when UE is currently using continuous data. If the current throughput
exceeds the value of the parameter, then OLPC is configured to use the peak data
rate configuration.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
194
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.11.24
Summary of changes
DynHSUPABLERMaxRateThrB (Peak rate threshold for bursty data
of Dyn HSUPA BLER)
Description
This parameter defines the peak rate threshold in relation to the UE's maximum
data rate. This parameter is used by the dynamic HSUPA BLER algorithm. The
outer loop power control of the RNC applies this parameter when UE is currently
using bursty data. If the current throughput exceeds the value of the parameter, then
the OLPC is configured to use the peak data rate configuration.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
1.1.11.25
PTTUEMappingARPCap (PTT UE mapping for ARP pre-emption
capability)
Description
The parameter defines value of the ARP pre-emption capability that is used to
identify a RAB as PTT RAB. If the value of this parameter does not match with the
related RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
195
Summary of changes
WCDMA Radio Network Configuration Parameters
1.1.11.26
PTTUEMappingARPVul (PTT UE mapping for ARP pre-emption vulnerability)
Description
The parameter defines value of the ARP pre-emption vulnerability that is used to
identify a RAB as PTT RAB. If the value of this parameter does not match with the
related RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
1.1.11.27
PTTUEMappingARPPrioLevel (PTT UE mapping for ARP priority
level)
Description
The parameter defines value of the ARP priority level that is used to identify a RAB
as PTT RAB. If the value of this parameter does not match with the related RAB
parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
196
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.11.28
Summary of changes
PTTUEMappingARPQue (PTT UE Mapping for ARP queuing
allowed)
Description
The parameter defines value of the ARP queuing allowed that is used to identify a
RAB as PTT RAB. If the value of this parameter does not match with the related
RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
1.1.11.29
PTTUEMappingSignInd (PTT UE mapping for Signaling indication)
Description
The parameter defines value of the Signaling indication that is used to identify a
RAB as PTT RAB. If the value of this parameter does not match with the related
RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
197
Summary of changes
1.1.11.30
WCDMA Radio Network Configuration Parameters
PTTUEMappingTC (PTT UE mapping for Traffic Class)
Description
The parameter defines value of the Traffic Class RAB parameter that is used to
identify a RAB as PTT RAB. If the value of this parameter does not match with the
related RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
1.1.11.31
PTTUEMappingTHP (PTT UE mapping for Traffic handling priority)
Description
The parameter defines value of the THP that is used to identify a RAB as PTT RAB.
If the value of this parameter does not match with the related RAB parameter value,
then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
The parameter is valid only in case of Interactive Traffic Class.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
198
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.11.32
Summary of changes
RAU_LAU_RestrictionInd (RAU and LAU Restriction Indication for
PPAC)
Description
The parameter defines routing area update, location update and initial direct
transfer restriction per CN domain. Valid when RNFC - PPACEnabled parameter is
enabled.
Related features
Paging Permission with Access Control (standard)
1.1.11.33
Description
DynHSUPABLERBurstDataRx (Retransmissions in Dyn HSUPA
BLER for Bursty Data)
This management parameter defines the L1 HARQ retransmissions threshold for
the outer loop power control entities dedicated to the E-DCH MAC-d flows of the PS
NRT RABs. Its value is used by the outer loop power control of the RNC for the
detection of the block error when the L1 BLER target is defined with the management parameter "Layer1 Bursty Data BLER target for E-DCH". Block error occurs if
the number of the retransmissions equals to or is bigger than the value of the
parameter or an E-HARQ failure has been observed. Outer loop power control
adjusts the uplink DPCCH SIR target after block errors occurs.
Note: Parameter values 2 and 3 will produce high BLER for first transmission.
Also those values will increase SIR target increase interval and thus effective BLER
is even higher.
Related features
1.1.11.34
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DynHSUPABLERContDataRx10 (Retransmissions in Dyn HSUPA
BLER for Cont Data 10msTTI)
Description
This management parameter defines the L1 HARQ retransmissions threshold for
the outer loop power control entities dedicated to the E-DCH 10 ms TTI MAC-d
flows of the PS NRT RABs. Its value is used by the outer loop power control of the
RNC for the detection of the block error when the L1 BLER target is defined with the
management parameter "Layer1 Continuous BLER target for E-DCH". Block error
occurs if the number of the retransmissions equals to or is bigger than the value of
the parameter or an E-HARQ failure has been observed. Outer loop power control
adjusts the uplink DPCCH SIR target after block errors occurs.
Note: Parameter values 2 and 3 will produce high BLER for first transmission.
Also those values will increase SIR target increase interval and thus effective BLER
is even higher.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
199
Summary of changes
1.1.11.35
WCDMA Radio Network Configuration Parameters
DynHSUPABLERContDataRx2 (Retransmissions in Dyn HSUPA
BLER for Cont Data 2 ms TTI)
Description
This management parameter defines the L1 HARQ retransmissions threshold for
the outer loop power control entities dedicated to the E-DCH 2 ms TTI MAC-d flows
of the PS NRT RABs. Its value is used by the outer loop power control of the RNC
for the detection of the block error when the L1 BLER target is defined with the management parameter "Layer1 Continuous BLER target for E-DCH". Block error
occurs if the number of the retransmissions equals to or is bigger than the value of
the parameter or an E-HARQ failure has been observed. Outer loop power control
adjusts the uplink DPCCH SIR target after block errors occurs.
Note: Parameter values 2 and 3 will produce high BLER for first transmission.
Also those values will increase SIR target increase interval and thus effective BLER
is even higher.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
1.1.11.36
Description
DynHSUPABLERPeakRateRx (Retransmissions in Dyn HSUPA
BLER for Peak data)
This management parameter defines the L1 HARQ retransmissions threshold for
the outer loop power control entities dedicated to the E-DCH MAC-d flows of the PS
NRT RABs. Its value is used by the outer loop power control of the RNC for the
detection of the block error when the L1 BLER target is defined with the management parameter "Layer1 Peak Data Rate BLER target for E-DCH". Block error
occurs if the number of the retransmissions equals to or is bigger than the value of
the parameter or an E-HARQ failure has been observed. Outer loop power control
adjusts the uplink DPCCH SIR target after block errors occurs.
Note: Parameter values 2 and 3 will produce high BLER for first transmission.
Also those values will increase SIR target increase interval and thus effective BLER
is even higher.
Related features
200
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.11.37
Summary of changes
RRCConnSetupMsgSize (RRC Connection Setup Message Size
Optimisation)
Description
This parameter indicates whether the RRC CONNECTION SETUP message size
optimisation functionality is enabled.
When enabled, this functionality introduces message size optimisation for RRC:
RRC CONNECTION SETUP message, which is achieved by sending Complete
Configuration (CC) with single Cell_DCH mapping. Because Cell_FACH mapping
is removed, RRC Connection Setup message size is reduced from 2 to 1 TB (Transport Block) resulting faster and more reliable signaling.
Other option for optimising RRC Connection Setup message is to use Default
Configuration (DC).
If either of above option is activated, RACH/FACH RB mapping information for
SRBs is provided after RRC connection setup procedure during the first Radio
Bearer Setup procedure, but with a separate Radio Bearer Reconfiguration procedure.
The RRC CONNECTION SETUP message size is not optimised if either the
value of this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
The complete parameter value descriptions are the following: 0 (Disabled), 1
(Default Configuration for rel6 and newer UEs and Complete Configuration with
dual mapping for rel5 and older UEs), 2 (Complete Configuration for rel5 and older
UEs with single mapping and Complete Configuration with dual mapping for rel6
and newer UEs), 3 (Default Configuration for rel6 and newer UEs and Complete
Configuration with single mapping for rel5 and older UEs), 4 (Complete Configuration for rel6 and newer UEs with single mapping and Complete Configuration with
dual mapping for rel5 and older UEs), 6 (Complete Configuration for all UEs with
single mapping)
Related features
Fast HSPA Mobility (optional)
1.1.11.38
DynHSUPABLERAlgTrgTime (Time to trigger Dyn HSUPA BLER
Algorithm)
Description
This parameter indicates the number of TTIs (10ms) after that Dynamic HSUPA
BLER Algorithm shall be triggered by outer loop power control in the RNC. This is
time to trigger type parameter. In case of 2ms TTI, this same parameter is used with
multiple of 5.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
1.1.11.39
Description
DN00211177
Issue 12B
DynHSUPABLERFrameWinSiz (Window size for FP Frames Measurement)
This parameter defines the size of the sliding averaging window for FP frames measurement of the E-DCH FP. The measurement measures the number of FP frames
transmitted by the E-DCH FP during the sliding measurement window. The parameter value 0 means that the E-DCH FP frames measurement is not performed.
Id:0900d805809da32a
201
Summary of changes
Related features
1.1.12
1.1.12.1
Description
WCDMA Radio Network Configuration Parameters
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
RNC
AlarmSetforWCELBLINIT (Alarm Set for WCEL BL-INIT)
This parameter is used to enable or disable the alarm setting for WCEL objects that
stay in BL-INIT state for excessive time.
Notes: activation (alarms get set after certain time for BL-INIT WCELs) and
deactivation (alarms are not set for BL-INIT WCELs, alarms set prior to deactivation
will stay active).
1.1.12.2
DSCPStatisticsGroupTCPack (DSCP code for DL TCP Ack statistics)
Description
This parameter defines which Iu-PS GTP user plane data DSCP code is mapped to
counter M1022Cxx DL TCP ACKs. This parameter defines the value of a DSCP
code that the operator sets for DL TCP ACKs for a specific UL data. This DSCP
value will be mapped to one of the six application groups configured by operator.
This parameter is used to update cell level counter to track number of incoming
DL TCP ACK packets with this specific DSCP marking.
Related features
Application Aware RAN (optional)
1.1.12.3
DSCPStatisticsGroupA (DSCP statistics group A )
Description
This parameter defines which Iu-PS GTP user plane data DSCP code is mapped to
counter M1022Cxx IUPS DSCP CLASS A. This parameter defines the value of a
DSCP level that the operator chooses to monitor in a cell.
This parameter is used to update cell level counter to track number of incoming
DL packets with DSCP marking A.
Related features
Application Aware RAN (optional)
1.1.12.4
DSCPStatisticsGroupB (DSCP statistics group B)
Description
This parameter defines which Iu-PS GTP user plane data DSCP code is mapped to
counter M1022Cxx IUPS DSCP CLASS B. This parameter defines the value of a
DSCP level that the operator chooses to monitor in a cell.
This parameter is used to update cell level counter to track number of incoming
DL packets with DSCP marking B.
Related features
Application Aware RAN (optional)
202
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.12.5
Summary of changes
DSCPStatisticsGroupC (DSCP statistics group C)
Description
This parameter defines which Iu-PS GTP user plane data DSCP code is mapped to
counter M1022Cxx IUPS DSCP CLASS C. This parameter defines the value of a
DSCP level that the operator chooses to monitor in a cell.
This parameter is used to update cell level counter to track number of incoming
DL packets with DSCP marking C.
Related features
Application Aware RAN (optional)
1.1.12.6
MACLogicalChPriority (MAC logical channel priority definition)
Description
This parameter defines MAC logical channel priority for Signalling Radio Bearers
SRB1, SRB2 and SRB3.
The MAC logical channel priority for SRB1, SRB2 and SRB3 can be defined
based on domain and Traffic Class (TC) .
These priorities are values in the range of 1 - 3. (1 is the highest and 3 is the
lowest priority).
For example, see the following prioritization orders:
Priority Default Config#1
1 SRBs (1-3) SRB 1
2 SRB 2
3 SRB 3
Child parameters
•
•
•
Related features
Fast Cell_PCH Switching (optional)
1.1.12.7
MACLogChPriSRB1
MACLogChPriSRB2
MACLogChPriSRB3
MACLogicalChPriority/MACLogChPriSRB1 (MAC logical channel
priority for SRB1)
Description
This parameter defines MAC logical channel priority for Signalling Radio Bearer1
Parent parameter
MACLogicalChPriority
Related features
Fast Cell_PCH Switching (optional)
1.1.12.8
MACLogicalChPriority/MACLogChPriSRB2 (MAC logical channel
priority for SRB2)
Description
This parameter defines MAC logical channel priority for Signalling Radio Bearer2
Parent parameter
MACLogicalChPriority
Related features
Fast Cell_PCH Switching (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
203
Summary of changes
1.1.12.9
WCDMA Radio Network Configuration Parameters
MACLogicalChPriority/MACLogChPriSRB3 (MAC logical channel
priority for SRB3)
Description
This parameter defines MAC logical channel priority for Signalling Radio Bearer3
Parent parameter
MACLogicalChPriority
Related features
Fast Cell_PCH Switching (optional)
1.1.12.10
Description
1.1.12.11
RncClientTLSMode (RNC Client TLS Mode)
Parameter defines the BTS O&M client connection mode which RNC uses when
connecting to OMS.
Off = Only insecure connection establishment is allowed
Probing = Both secure and insecure connection establishments are allowed
Forced = Only secure connection establishment is allowed
Parameter defines the RNC TLS Mode parameter value for the BTS O&M client,
which is used in start-up to determine the correct security operational mode of the
BTS O&M connection establishment towards OMS. Parameter can be configured
locally in RNC.
CBCSourceIPAddress (Source IP address for IuBC interface)
Description
Source IP address used for SABP application towards one CBC. Same address can
be used for max 4 CBCs.
Examples:
IPv4, 255.255.255.255, 1.1.1.1
Related features
Source IP on ICSU used for IuBC interface (standard) AND Service Area Broadcast (optional)
1.1.12.12
UePeriodicMeasCpuLimit (UE Periodic Measurement Report CPU
Limit)
Description
If the CPU load of a unit rises over this limit, no new measurements are started
regarding to feature UE Periodic Measurement Report.
Related features
UE Periodic Measurement Report (optional)
1.1.12.13
UePeriodicMeasInterval (UE Periodic Measurement Report Measurements Interval)
Description
The operator can set the interval for UE Periodical Measurement Reports.
Related features
UE Periodic Measurement Report (optional)
204
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.12.14
Description
Summary of changes
WCELIdleAlarmTimeout (WCEL Idle Alarm Timeout)
This parameter determines time interval after which WCELs staying in BL-INIT state
are informed to the user via alarms.
1.1.13
1.1.13.1
RNFC
AutoACResEnabled (Automatic Access Class Restriction Enabled)
Description
This parameter enables/disables the use of Automatic Access Class restriction in
the RNC for different overload triggers. Activation and deactivation can be done
separately for different overload triggers.
‘Automatic Access Class Restriction’ uses a binary notation of 4 bits where:
- bit 0 indicates whether or not the feature is activated for the Total Received
wideband power
- bit 1 indicates whether or not the feature is activated for NRT scheduling queue
length
- bit 2 indicates whether or not the feature is activated for the CN overload
- bit 3 indicates whether or not the feature is activated for the RNC overload
If a bit is set to 1, the feature is activated for the corresponding overload trigger.
If a bit is set to 0, the feature is not activated for the corresponding overload trigger
e.g. If a bit0 is set to 1 then Total Received wideband power trigger is activated. If
a bit0 is set to 0 then Total Received wideband power trigger is de-activated.
Active triggers can restricted the number of UE Access Classes using SIB
messages in case overload is detected due to those triggers. Restricted access
classes cannot access radio network.
Automatic Access Class restriction feature is enabled, if at least one bit (bit0,
bit1, bit2, bit3) is set to 1.
Note: Parameters of mass event handler must be configured if NRT queue
length functionality is activated (bit1 is set to 1).
Related features
Automatic access class restriction (optional)
1.1.13.2
CSFBEnabled (CSFB Enabled)
Description
The parameter indicates whether CS Fallback (RAN2435) functionality is enabled
in the RNC or not.
CSFB functionality is activated in the cell only if both parameters CSFBEnabled
(for RNC) and IncomingLTEISHO (for cell) are in state Enabled. RAN 2435 SRVCC
from LTE and CCSFB with HO feature needs license RAN2067 LTE InterworkingISHO from LTE
Related features
SRVCC from LTE and CSFB with HO (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
205
Summary of changes
1.1.13.3
WCDMA Radio Network Configuration Parameters
DCH00SuppOnIurEnabled (DCH 0/0 Support On Iur Enabled)
Description
This parameter defines whether the AMR with DCH 0/0 Support on Iur feature is
enabled in the RNC. When enabled in the RNC, this feature introduces DRNC
support for establishing DCH 0/0 PS RB on Iur.
The feature is out of use in the RNC if either the state of the license is "Off/Config", or the value of this parameter is set to 'Disabled'.
Related features
AMR with DCH (0,0) Support on Iur (optional)
1.1.13.4
Description
DCHtoPCHEnabled (Enabling direct Cell_DCH to PCH state transition)
This parameter defines whether direct transition from Cell_DCH to Cell_PCH is
allowed or not.
1.1.13.5
FastPCHSwitchEnabled (Enabling Fast Cell_PCH Switching feature)
Description
This parameter enables/disables the RAN2494 (Fast Cell_PCH Switching) feature.
Fast Cell PCH Switching feature attempts to make faster transition from
Cell/URA_PCH / Cell_FACH to Cell_DCH.
Related features
Fast Cell_PCH Switching (optional)
1.1.13.6
FasterOLPCEnabled (Faster OLPC Enabled)
Description
This parameter determines the Activation/Deactivation of Faster Outer Loop Power
Control functionality in use.
If the parameter is set to enabled, following parameters are used to determine
the value of Discontinuous transmission period value, minimum step size for SIR
target modification and SIR target modification interval
•ULFastOLPCDTXthld
•FOLPCStepSizSIRTgt
•FOLPCSIRTgtModInt
which makes the OLPC to adjust the SIR target of the call faster.
Otherwise, legacy handling i.e. internal constant values are followed to determine these values.
Related features
Faster OLPC (standard)
206
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.13.7
Summary of changes
FemtoHandoverControl (Femto Handover Control)
Description
This parameter determines whether or not the Femto Handover Control feature is
enabled in the RNC. When the Femto Handover Control feature is enabled in the
RNC, the RNC excludes specified neighbour cells from the neighbour cell lists that
are signaled to the UE in CELL_DCH state of connected mode. Consequently, intrafrequency, inter-frequency and inter-system handovers are disabled to the specified
neighbour cells when the Femto Handover Control feature is enabled in the RNC.
If the Femto Handover Control feature is disabled in the RNC, all neighbour
cells are included in the neighbour cell lists that are signaled to the UE in
CELL_DCH state of connected mode and subscribers are allowed to make handovers to all neighbour cells.
The parameters ADJS–AdjsSIB, ADJI–AdjiSIB and ADJG–AdjgSIB specify the
intra-frequency, inter-frequency and GSM neighbour cells which are excluded from
the neighbour cell lists that are signaled to the UE in CELL_DCH state.
Note that this parameter or the Femto Handover Control feature does not have
any effect to the information broadcasted in the System Information Block
11&12&18 messages.
Related features
Femto Handover Control (optional)
1.1.13.8
FlexULRLCEnabled (Flexible UL RLC Enabled)
Description
This parameter enables/disables use of feature Flexible UL RLC. If the parameter
is enabled (1), then feature Flexible UL RLC is used in the RNC. If the parameter is
disabled (0), then feature Flexible UL RLC is not used in the RNC.
Related features
( HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional) OR HSUPA 60 Users per
BTS (optional) ) AND HSDPA with QPSK and 5 Codes (optional) AND HSDPA
Dynamic Resource Allocation (optional)
1.1.13.9
HSUPADynBLEREnabled (HSUPA Dynamic BLER Enabled)
Description
This parameter Enables/Disables the Dynamic adjustment of HSUPA BLER.
Dynamic HSUPA BLER estimation algorithm defines BLER target for peak data
rate, bursty data rate and continuous data rate separately
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
1.1.13.10
IFHOOverIurExt (IFHO Over Iur Extension)
Description
This parameter enables or disables the IFHO Over Iur Enhancements functionality
introduced by IUR Mobility Enhancements feature in the RNC.
Related features
I-BTS Sharing (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
207
Summary of changes
1.1.13.11
WCDMA Radio Network Configuration Parameters
LFDProfEnabled (LFD profiling Enabled)
Description
LFD (Legacy Fast Dormancy) profiling Enabled parameter Enables/Disables the
use of LFD Profiling in RNC.
Related features
Fast Dormancy Profiling (optional)
1.1.13.12
PPACEnabled (Paging Permission With Access Control Enabled)
Description
The parameter defines whether or not the PPAC feature is enabled in the RNC.
When enabled in the RNC, this feature introduces possibility for UE to answer to
paging message or perform routing or location update even though the access class
of the UE is barred.
The feature is out of use in the RNC if the value of this parameter is set to
'Disabled'.
Before enabling the feature the paging response restriction per CN domain shall
be defined with parameter RNAC - PagingRestrictionInd and the routing/location
area update restriction per CN domain shall be defined with parameter RNAC –
RAU_LAU_RestrictionInd. By default all paging responses and RAU/LAU are
restricted.
Related features
Paging Permission with Access Control (standard)
1.1.13.13
PTTEnabled (Push to talk enabled)
Description
The parameter enables/disables RAN2300 Optimized push to talk experience
feature. It also allows/denies use of different transport channel types for UE with
push to talk (PTT) RAB. If the transport type is not allowed to be used, then that configuration is not used for PTT UE.
If the parameter value is changed, then the new value is used just for the RAB
setups done after the parameter change (already setup RABs are not affected).
The following alternatives can be used:
- feature is disabled
- DCH/DCH allowed
- DCH/DCH and DCH/HS-DSCH allowed for radio bearers
- DCH/DCH, DCH/HS-DSCH and E-DCH/HS-DSCH allowed for radio bearers
- all supported combinations allowed (also SRBs on HSPA and SRBs on
HSUPA).
Use of different transport channel types can be defined also based on Traffic
Class and Traffic Handling Priority with the parameters: FDPCHAndSRBOnHSPATC, EDCHQOSClasses and HSDSCHQoSclasses. PTT RAB is handled there
according of it's Traffic Class received from core network in RAB parameters.
Notice: If use of some configuration for PTT is enabled with this parameter, it
does not mean directly that configuration will be used, because use of different configurations depends on UE and BTS capabilities, other activated features and
resource situation in RAN.
Notice: feature is not supported by NB/RSxxx BTS, so it must not be activated
if there are those BTSs under the RNC.
Related features
Optimised push to talk experience (optional)
208
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.13.14
Summary of changes
SRVCCEnabled (SRVCC Enabled)
Description
The parameter indicates whether Single Radio Voice Call Continuity (RAN2435)
functionality is enabled in the RNC or not.
SRVCC functionality is activated in the cell only if both parameters SRVCCEnabled (for RNC)and IncomingLTEISHO (for cell) are in state Enabled. SRVCC from
LTE feature needs license for RAN2067 LTE Interworking-ISHO from LTE
Related features
SRVCC from LTE and CSFB with HO (optional)
1.1.14
1.1.14.1
Description
DN00211177
Issue 12B
RNHSPA
AARConfigTable (Application Aware RAN Configuration Table)
This parameter defines the configuration table needed for each application group in
case of Application Aware RAN feature. This parameter indicates that Application
Group Id, DSCP codes (upto 5 unique codes), Precedence and Target SPI for each
Initial SPI value assigned to the corresponding application group.
In case of Application Aware RAN feature a maximum of 6 Application groups
can be defined and for each Application Group a maximum of five unique DSCP
codes are allowed.
For each Application Group a unique Precedence value is assigned. Precedence value dictates what SPI should be chosen when packets belonging to
multiple application groups are detected by the RNC. In such cases the target SPI
shall be defined by the Application group having the lowest precedence value. The
lowest value of precedence means highest priority during rule evaluation.
With Application Aware RAN feature ,Initial SPI of the radio bearer is demoted
or promoted in the RNC PDCP layer according to Deep Packet Inspection (DPI)
marking. Operator can configure the promotion/demotion of the initial SPI or not to
change the initial SPI for certain type of data as pleased. Target SPI indicates the
new SPI value assigned to an application group after promotion or demotion of inital
SPI or no change action.
Id:0900d805809da32a
209
Summary of changes
WCDMA Radio Network Configuration Parameters
Child parameters
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Related features
Application Aware RAN (optional)
1.1.14.2
AppGrpId
DSCPCode1
DSCPCode2
DSCPCode3
DSCPCode4
DSCPCode5
Precedence
TargetSPIforSPI0
TargetSPIforSPI1
TargetSPIforSPI10
TargetSPIforSPI11
TargetSPIforSPI2
TargetSPIforSPI3
TargetSPIforSPI4
TargetSPIforSPI5
TargetSPIforSPI6
TargetSPIforSPI7
TargetSPIforSPI8
TargetSPIforSPI9
AARConfigTable/AppGrpId (Application Group Identifier)
Description
Identifier of the Application Group in case of Application Aware RAN feature.A set
of applications requiring the same treatment at RAN might be grouped by the
operator into Application Groups. There can be maximum of six Application Groups
defined by the operator in case of Application Aware RAN feature.
Default value or special value '255' means that the Application Group Identifier
has not been defined by the operator and hence cannot be used.Allowed range is
1 to 6 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.3
Description
210
AARConfigTable/DSCPCode1 (DSCP Code1)
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature. One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.4
Summary of changes
AARConfigTable/DSCPCode2 (DSCP Code2)
Description
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature.One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.5
Description
AARConfigTable/DSCPCode3 (DSCP Code3)
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature.One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
211
Summary of changes
1.1.14.6
WCDMA Radio Network Configuration Parameters
AARConfigTable/DSCPCode4 (DSCP Code4)
Description
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature.One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.7
AARConfigTable/DSCPCode5 (DSCP Code5)
Description
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature.One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.8
VCPHSDPAPrevDuration (Duration of HSDPA prevention for Voice
Call Priority)
Description
The parameter determines the minimum duration of HSDPA prevention for the
Voice Call Prioritisation during High Traffic Load.
The shorter the value of the parameter, the shorter duration the HSDPA prevention is applied. Correspondingly, the longer value of the parameter, the longer
duration the HSDPA prevention is applied.
Special value 0 means that AMR prioritisation is applied without HSDPA prevention.
The function is switched on/off by the WCEL-VoiceCallPriority parameter.
Related features
Voice Call Priorization during High Traffic Load (optional)
212
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.14.9
Summary of changes
MaxEHARQReTxPSconv10 (E-DCH max number of retransmissions
PS conv E-TTI 10)
Description
This parameter determines the maximum number of HARQ retransmissions for the
E-DCH MAC-d flow of the PS conversational or push to talk RAB when the E-TTI is
10 ms.
Information is signaled to UE using RRC: E-DCH MAC-d flow maximum number
of retransmissions information element and to BTS using NBAP: Maximum Number
of Retransmissions for E-DCH information element.
Use of too high or low value can cause voice quality problems (delay or data
loss).
Related features
Optimised push to talk experience (optional)
1.1.14.10
MaxEHARQReTxPSconv2 (E-DCH max number of retransmissions
PS conv E-TTI 2)
Description
This parameter determines the maximum number of HARQ retransmissions for the
E-DCH MAC-d flow of the PS conversational or push to talk RAB when the E-TTI is
2 ms.
Information is signaled to UE using RRC: E-DCH MAC-d flow maximum number
of retransmissions information element and to BTS using NBAP: Maximum Number
of Retransmissions for E-DCH information element.
Use of too high or low value can cause voice quality problems (delay or data
loss).
Related features
Optimised push to talk experience (optional)
1.1.14.11
PowerOffsetEHARQPSConv (HARQ power offset for E-DCH MAC-d
flow of PS conv)
Description
This parameter defines the HARQ power offset value for the E-DCH MAC-d flow of
the PS conversational or push to talk service. The parameter is applicable if another
E-DCH MAC-d flow than one of the signaling link can be multiplexed within the
MAC-e PDU with the E-DCH MAC-d flow of the PS conversational, or if the power
offset of the signaling link E-DCH MAC-d flow equals to 0 dB. Power offset value is
used for both E-TTI values 2 ms and 10 ms.
Use of high value wastes radio resources and use of low value can cause voice
quality problems.
Related features
Optimised push to talk experience (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
213
Summary of changes
1.1.14.12
WCDMA Radio Network Configuration Parameters
DiscardTimerPTT (HSDPA Discard Timer for the PTT)
Description
The parameter defines the HSDPA Discard Timer value for the HS-DSCH MAC-d
flow of the PTT bearer. Discard Timer defines the time to live for a MAC-hs/ehs SDU
starting from the instant of its arrival into an HSDPA Priority Queue. BTS can use it
as delay information for guiding the scheduling.
Too small value can cause dropping the data too soon and too big value can
cause extra delay for data. In both cases the voice quality is weaken.
Related features
Optimised push to talk experience (optional)
1.1.14.13
T1PTT (HSDPA re-ordering rel timer T1 for the PTT)
Description
The parameter defines the value of the HSDPA re-ordering release timer T1 for the
HS-DSCH MAC-d flow of the PTT bearer. In the expiration of the timer, the reordering entity in the UE releases MAC-ehs PDUs to the upper layers even though there
were outstanding PDUs with lower sequence numbers. BTS might use the timer to
stop the HSDPA retransmission of the associated MAC-ehs PDUs.
Too small or big value weakens the voice quality.
Related features
Optimised push to talk experience (optional)
1.1.14.14
VCPHSDPAUserIncr (HSDPA user increment for the Voice Call Priority)
Description
The parameter determines the HSDPA user increment for the Voice Call Prioritisation during High Traffic Load. The HSDPA user increment defines how fast the
original maximum number of HSDPA users in the cell is restored after HSDPA prevention ceases.
The Voice Call Prioritisation during High Traffic Load uses the temporary
maximum number of HSDPA users to limit HS-DSCH allocations in the cell during
high load. When the usage of the maximum number of HSDPA users ceases, the
original maximum number of HSDPA users is restored gradually. The value of the
parameter defines how many HSDPA users can be added per second after HSDPA
prevention ceases.
Special value (0) means that restoration happens immediately. The value 1
restores the original maximum number of HSDPA users slowly, the value 10
restores the original value fast. The fast or immediate restoration is seen as oscillation between low and high maximum number of users if load varies in the cell.
Temporary maximum number of HSDPA users is defined by the WCEL-VCPMaxHSDPAUsers parameter.
Usage of the function is controlled by the WCEL-VoiceCallPriority parameter.
Related features
Voice Call Priorization during High Traffic Load (optional)
214
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.14.15
Summary of changes
MEHHSUPAUserIncr (HSUPA user increment for the Mass Event
Handler)
Description
The parameter determines the HSUPA user increment for the Mass Event Handler.
The HSUPA user increment determines how fast the original maximum number of
HSUPA users in the cell is restored after the high load state ceases.
The Mass Event Handler uses the temporary maximum number of HSUPA
users to limit E-DCH allocations in the cell during the high load state. When the
usage of the maximum number of HSUPA users ceases, the original maximum
number of HSUPA users is restored gradually. The value of the parameter defines
how many HSUPA users can be added per second after the high load state ceases.
Special value (0) means that restoration happens immediately. The value 1
restores the original maximum number of HSUPA users slowly, the value 10
restores the original value fast. The fast or immediate restoration is seen as oscillation between low and high maximum number of users if load varies in the cell.
Temporary maximum number of HSUPA users is defined by the WCEL-MEHMaxHSUPAUsers parameter.
Related features
Mass Event Handler (optional)
1.1.14.16
InitialSPINRT (Initial SPI for PS NRT RAB)
Description
This parameter defines the Initial Scheduling Priority Indicator to be used for the PS
NRT HSPA or HSDPA RAB incase of Application Aware RAN feature. The Initial
Scheduling Priority Indicator for PS NRT HSPA/HSDPA RAB is set according to this
parameter when Qos Aware Scheduling feature is disabled while Application Aware
RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial Scheduling Priority Indicator is choosen
according to the principles defined by Qos Aware HSPA Scheduling feature ie
based on the TC/THP/ARP combination via RNPS-QosPriorityMapping parameter.
Values "5"(SPI 5) and "6" (SPI 6) define the Initial SPI to be either 5 or 6 for the
NRT bearers when the RAN1262 Qos feature is disabled to get better differentiation
when doing SPI promotion / demotions for the data between bearers .
Related features
Application Aware RAN (optional)
1.1.14.17
AARConfigTable/Precedence (Precedence)
Description
This parameter defines the precedence value assigned to a corresponding Application Group incase of Application Aware RAN feature.Precedence value dictates
what SPI should be chosen when packets belonging to multiple application groups
are detected by the RNC. The lowest value of precedence means highest priority.Default value or special value '255' means that the Precedence value has not
been defined by the operator for a given application group and hence cannot be
used.Allowed range is 1 to 6 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
215
Summary of changes
1.1.14.18
WCDMA Radio Network Configuration Parameters
PTTRLCPDUSizeHSDSCH (RLC PDU size for PTT mapped to HSDSCH)
Description
The parameter defines the possible RLC PDU sizes for PTT service in case of HSDSCH.
If the use of 656 is allowed with this parameter, then the selection of DL RLC
PDU size is done according of UE and BTS capability and activation of 656 with the
RNP parameter PDUSize656WithHSDSCH.
With the smaller value it takes more time to transfer data, but less power is
needed.
Related features
Optimised push to talk experience (optional)
1.1.14.19
AARConfigTable/TargetSPIforSPI0 (Target SPI for SPI 0)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 0 in case of Application Aware RAN feature. This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 0 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
0 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.20
Description
216
AARConfigTable/TargetSPIforSPI1 (Target SPI for SPI 1)
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 1 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 1 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
1 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.21
Summary of changes
AARConfigTable/TargetSPIforSPI10 (Target SPI for SPI 10)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 10 in case of Application Aware RAN feature.This parameter indicates the new SPI assigned to a given application group after promotion or
demotion of Initial SPI 10 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
10 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.22
AARConfigTable/TargetSPIforSPI11 (Target SPI for SPI 11)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 11 in case of Application Aware RAN feature.This parameter indicates the new SPI assigned to a given application group after promotion or
demotion of Initial SPI 11 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
11 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
217
Summary of changes
1.1.14.23
WCDMA Radio Network Configuration Parameters
AARConfigTable/TargetSPIforSPI2 (Target SPI for SPI 2 )
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 2 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 2 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
2 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.24
AARConfigTable/TargetSPIforSPI3 (Target SPI for SPI 3 )
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 3 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 3 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
3 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
218
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.14.25
Summary of changes
AARConfigTable/TargetSPIforSPI4 (Target SPI for SPI 4)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 4 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 4 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
4 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.26
AARConfigTable/TargetSPIforSPI5 (Target SPI for SPI 5)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 5 in case of Application Aware RAN feature. This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 0 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
5 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
219
Summary of changes
1.1.14.27
WCDMA Radio Network Configuration Parameters
AARConfigTable/TargetSPIforSPI6 (Target SPI for SPI 6)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 6 in case of Application Aware RAN feature. This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 6 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
6 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.28
AARConfigTable/TargetSPIforSPI7 (Target SPI for SPI 7)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 8 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 8 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
8 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
220
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.14.29
Summary of changes
AARConfigTable/TargetSPIforSPI8 (Target SPI for SPI 8)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 8 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 8 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
8 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
1.1.14.30
AARConfigTable/TargetSPIforSPI9 (Target SPI for SPI 9)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 9 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 9 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
9 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
221
Summary of changes
1.1.14.31
WCDMA Radio Network Configuration Parameters
MEHCQIFeedbackCycle (Temporary CQI feedback cycle for the
Mass Event Handler)
Description
The parameter determines the temporary CQI feedback cycle for the Mass Event
Handler.
Temporary CQI feedback cycle is used for a user not using CPC if the number
of HSDPA users attains or exceeds the threshold defined by the parameter WCELMEHHSDPAUserNbrCQI.
The longer the CQI feedback value, the less UL interference caused by the
periodical CQI reporting of the HSDPA UE. The longer CQI feedback cycle may
affect negatively to HSDPA scheduling performance.
The function is switched on/off by the WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
1.1.14.32
SmartHSPATimeToTrigger (Time-to-trigger for Smartphone
throughput measurement)
Description
Parameter defines the time-to-trigger values of the HS-DSCH MAC-d flow low utilisation measurement and E-DCH MAC-d flow low throughput measurement for the
identified Smartphone instead of the MACdflowutilTimetoTrigger and EDCHMACdFlowThroughputTimetoTrigger parameters.
Related features
Fast Dormancy Profiling (optional)
1.1.14.33
SmartHSPATputAveWin (Window size for Smartphone throughput
measurement)
Description
Parameter defines the HS-DSCH and E-DCH sliding averaging window sizes of the
throughput measurements for the identified Smartphone instead of the MACdflowthroughputAveWin and EDCHMACdFlowThroughputAveWin parameters.
The throughput measurement measures the number of bits transmitted by
MAC-d entity during the sliding measurement window defined by this parameter.
Value 0 means that the MAC-d flow throughput measurement is not activated.
Related features
Fast Dormancy Profiling (optional)
1.1.15
1.1.15.1
RNMOBI
SmartLTELayeringServ (Smart LTE Layering service control)
Description
The parameter defines what services are allowed to be moved to LTE by Smart LTE
Layering feature. Only services of PS domain can be controlled with this parameter.
UEs with services not supported in LTE should not be redirected to LTE,
because it is possible that those UEs comes back to WCDMA right away.
Smart LTE Layering is enabled with the SmartLTELayeringEnabled parameter.
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
222
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.15.2
Summary of changes
SmartLTELayeringPrevT (Timer for Smart LTE Layering Prevention)
Description
The parameter defines a minimum time that the UE must be in WCDMA system
after RRC Connection Setup Complete has been received or when Relocation
Request for PS service is received from LTE. An UE can be redirected to LTE by
Smart LTE Layering feature after the timer defined by this parameter expires. When
this timer is running the Smart LTE Layering is not triggered.
Setting timer value too low may cause ping pong redirections between WCDMA
and LTE. Setting timer value too high may cause that redirection to LTE is not triggered as frequently as would be most effective
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
1.1.16
1.1.16.1
RNPS
SmartInactTimerFACH (Inactivity Timer for Smart Phones in
Cell_FACH)
Description
Inactivity Timer for Smart Phones in Cell_FACH is used on MAC -c to detect the idle
periods on data transmission (NRT RBs and SRBs) for the LFDphones in
CELL_FACH state. Based on this timer the MAC -c shall give No_Data indication to
RRC, which further can change the state of the UE from Cell_FACH state to the
Cell_PCH state (or URA_PCH state).
Related features
Fast Dormancy Profiling (optional)
1.1.16.2
SmartInactivityTimerDCH (Inactivity timer for Smartphone DCH)
Description
Parameter defines the time indicating how long the radio and transmission
resources are reserved for Smartphone after inactivity detection on DCH. The
parameter is used for the identified Smartphone instead of the InactivityTimerDownlinkDCH and InactivityTimerUplinkDCH parameters.
This parameter defines the value for each DCH bit rate in downlink and uplink.
Parameter value 255 means that Smartphone specific DCH inactivity timers
are not used.
Related features
Fast Dormancy Profiling (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
223
Summary of changes
1.1.16.3
WCDMA Radio Network Configuration Parameters
PTTDormancyTimer (PTT dormancy timer)
Description
The parameter defines how long the PTT RAB which is identified as inactive is
allowed to keep the dedicated resources for radio bearer. If the dormancy timer
expires, then the dedicated resources of PTT radio bearer are released.
DCH transport channel type resource release is done when inactivity has lasted
the time which is defined by the PTTDormancyTimer parameter. E-DCH and HSDSCH transport channel type radio resource release is done when NRT service
specific conditions based inactivity has lasted the time which is defined by the
PTTDormancyTimer parameter.
Too small value of this timer causes extra signaling and setup delay for PTT
service. Too big value of this timer causes wasting of RAN resources.
Related features
Optimised push to talk experience (optional)
1.1.16.4
MEHTVMPendingTime (Temporary TVM pending time for the Mass
Event Handler)
Description
The parameter determines the increased TVM pending time during high load for the
Mass Event Handler.
If the high load state is detected based on the average length of the NRT scheduling queue, the increased TVM pending time is taken into use instead of the values
defined by the TrafVolPendingTimeUL and TrafVolPendingTimeDL parameters.
"Pending time after trigger" IE and "Tx interruption after trigger" IE are reconfigured
to UE.
The longer "Pending time after trigger" and "Tx interruption after trigger"
prevents UE from sending frequent and repetitive UL capacity requests and data
during high load. This will decrease UL interference and RACH load in the network.
Increased TVM pending time defined by this parameter is used only if the value
is longer than the values defined by the TrafVolPendingTimeUL and TrafVolPendingTimeDL parameters.
Functionality is switched on/off by the WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
1.1.17
1.1.17.1
Description
224
RNRLC
AMRLCHSRACHPS (AM RLC configuration for PS NRT with HSRACH)
This parameter defines the retransmission parameters for the AM RLC of the PS
RAB using E-DCH in its data transfer direction on CELL_FACH state. The parameter enables to activate the RLC polling and status reporting triggers and define their
values. The parameter also defines whether the SDU discard or No_discard after
MaxDAT number of transmissions is used as the general SDU discard mode and
the values for the numbers of the transmissions of the RLC PDUs. The RLC entity
of the UE can be configured to use the in-sequence delivery of the SDUs.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Child parameters
•
•
•
•
•
•
•
•
•
•
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.2
Summary of changes
AMRLCHSRACHPSMaxDAT
AMRLCHSRACHPSMaxMRW
AMRLCHSRACHPSMaxRST
AMRLCHSRACHPSPeriodMax
AMRLCHSRACHPSPeriodMin
AMRLCHSRACHPSPollPDU
AMRLCHSRACHPSPollSDU
AMRLCHSRACHPSPollWin
AMRLCHSRACHPSTriggers
HSRACHAMRLCRespHSFACH
AMRLCHSRACHPS/AMRLCHSRACHPSMaxDAT (AM RLC MaxDAT
transmissions for PS NRT with HS-RACH)
Description
This parameter defines the value of the RLC protocol parameter MaxDAT for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter
defines the maximum number of transmissions for the AMD PDU, which is set equal
to the MaxDAT-1. The value of the parameter is signalled to the RLC entity of the
UE rounded up to the closest value allowed in the RRC signaling.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.3
AMRLCHSRACHPS/AMRLCHSRACHPSMaxMRW (AM RLC
MaxMRW transmissions for PS NRT with HS-RACH)
Description
This parameter defines the value of the RLC protocol parameter MaxMRW for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter
defines the maximum number of transmissions for the move MRW command, which
is set equal to the MaxMRW-1. The value of the parameter is signalled to the RLC
entity of the UE rounded up to the closest value allowed in the RRC signalling. The
parameter is significant only if the SDU discard after MaxDAT retransmissions is
applied.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
225
Summary of changes
WCDMA Radio Network Configuration Parameters
1.1.17.4
AMRLCHSRACHPS/AMRLCHSRACHPSMaxRST (AM RLC MaxRST
transmissions for PS NRT with HS-RACH)
Description
This parameter defines the value of the RLC protocol parameter MaxRST for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter
defines the maximum number of transmissions for the RLC RESET PDU, which is
set equal to the MaxRST-1. The value of the parameter is signalled to the RLC entity
of the UE rounded up to the closest value allowed in the RRC signalling.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.5
AMRLCHSRACHPS/AMRLCHSRACHPSPollPDU (AM RLC period
Poll_PDU for PS NRT with HS-RACH)
Description
This parameter defines the minimum value of the RLC protocol parameter
Poll_PDU for the AM RLC entity of the PS radio bearers when data is transferred
over HS-RACH on CELL_FACH state using E-DCH transport channel. The value of
the parameter indicates how often the sender polls the receiver in accordance with
the activation of the poll trigger 'polling every Poll_PDU PDU'. The value of the
parameter is expressed in relation to the size of the allocated transmission window
for the AMR RLC entity. It is transformed into the corresponding number of the AMD
PDUs rounding up to the closest integer and it is configured to the AM RLC entity.
Poll_PDU can be set to a bigger value with other means. The value is signalled to
the RLC entity of the UE rounded up to the closest value or down to the maximum
value allowed in the RRC signalling. The trigger is applied if it has been activated
with the "AM RLC status report triggers for PS NRT with HS-RACH" parameter.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.6
AMRLCRTTPollPDUSatellite (AM RLC period Poll_PDU with satellite
Iub)
Description
This parameter defines the AM RLC Round Trip Time (RTT) for the data transfer
when the radio bearer is mapped to the DCH, HS-DSCH or E-DCH and satellite Iub
is applied. The parameter is used to define the AM RLC status reporting and polling
period lengths.
This parameter is not taken into account when Satellite Iub is disabled for the
BTS.
When value is changed it is taken into account only for new connections.
Related features
Satellite Iub (optional)
226
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.17.7
Summary of changes
AMRLCHSRACHPS/AMRLCHSRACHPSPollSDU (AM RLC period
Poll_SDU for PS NRT with HS-RACH)
Description
This parameter defines the value of the RLC protocol parameter Poll_SDU for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter indicates in number of the RLC SDUs how often the sender polls the receiver in accordance with the activation of the poll trigger 'polling every Poll_SDU SDU'. The value
is signalled to the RLC entity of the UE rounded up to the closest value or down to
the maximum value allowed in the RRC signalling. The trigger is applied if it has
been activated with the "AM RLC status report triggers for PS NRT with HS-RACH"
parameter.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.8
AMRLCHSRACHPS/AMRLCHSRACHPSPollWin (AM RLC period
Poll_Window for PS NRT with HS-RACH)
Description
This parameter defines the value of the RLC protocol parameter Poll_window for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter indicates how often the sender polls the receiver in accordance with the activation of
the poll trigger 'window based polling'. The value is signalled to the RLC entity of the
UE rounded up to the closest value allowed in the RRC signalling. The trigger is
applied if it has been activated with the "AM RLC status report triggers for PS NRT
with HS-RACH" parameter.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.9
AMRLCSRB3n4RespTime (AM RLC round trip time for SRB3 and
SRB4)
Description
The parameter defines the AMRLC Round Trip Time (RTT) for the data transfer for
SRB3 and SRB4 for all kinds of variations of transport channel used or SRB bitrate.
It is used to estimate the average response time from the moment when the AM
RLC entity sends an AMD PDU to its peer entity with the poll bit set to the receiving
moment of the corresponding status PDU. The RTT depends on the L1/L2 processing delay of the UE and the RNC, type of the reverse transport channel - DCH, HSDSCH or E-DCH, processing delay of the BTS, the Uu interface delay, and the Iub
transfer delay. The parameter is used to define the AM RLC status reporting and
polling period lengths.
Related features
Fast Cell_PCH Switching (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
227
Summary of changes
1.1.17.10
WCDMA Radio Network Configuration Parameters
AMRLCRespTimeHSSRB (AM RLC round trip time for SRBs with
HS-RACH/HS-FACH)
Description
This parameter defines the AM RLC Round Trip Time (RTT) for the UL/DL SRB data
transfer when the singnalling radio bearer is mapped to HS-RACH in UL and HSFACH in DL on CELL_FACH state (UL SRB using E-DCH transport channel and DL
SRB using HS-DSCH transport channel). It is used to estimate the average
response time from the moment that the AM RLC entity sends an AMD PDU to its
peer entity with the poll bit set to the receiving moment of the corresponding status
PDU. The RTT depends on the L1/L2 processing delay of the UE and the RNC, processing delay of the BTS, the Uu interface delay, and the Iub transfer delay. The
parameter is used to define the AM RLC status reporting and polling period lengths.
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.11
AMRLCHSRACHPS/HSRACHAMRLCRespHSFACH (AM RLC round
trip time with HS-RACH/HS-FACH)
Description
This parameter defines the AM RLC Round Trip Time (RTT) for the UL data transfer
when the radio bearer is mapped to the HS-RACH on CELL_FACH state using EDCH transport channel and the reverse transport channel is the HS-DSCH. It is
used to estimate the average response time from the moment that the AM RLC
entity sends an AMD PDU to its peer entity with the poll bit set to the receiving
moment of the corresponding status PDU. The RTT depends on the L1/L2 processing delay of the UE and the RNC, processing delay of the BTS, the Uu interface
delay, and the Iub transfer delay. The parameter is used to define the AM RLC
status reporting and polling period lengths.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.12
AMRLCHSRACHPS/AMRLCHSRACHPSPeriodMax (AM RLC status
period max for PS NRT with HS-RACH)
Description
This parameter defines the maximum status reporting period of the AM RLC in
relation to the RLC round trip time for the PS radio bearers when data is transferred
over HS-RACH on CELL_FACH state using E-DCH transpport channel. The
maximum value is used as the value of the AM RLC timers Timer_Poll,
Timer_poll_periodic, Timer_status_periodic, and Timer_MRW and Timer_RST in
accordance with their activations with the "AM RLC status report triggers for PS
NRT with HS-RACH" parameter. The value is configured as such to the RLC entity
of the RNC. The value is signalled to the RLC entity of the UE rounded up to the
closest value or down to the maximum value allowed in the RRC signalling.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
228
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.17.13
Summary of changes
AMRLCSRB3n4PeriodMax (AM RLC status period max for SRB3 and
SRB4)
Description
The parameter defines the maximum status reporting period of the AM RLC in
relation to the RLC round trip time for SRB3 and SRB4 for all kinds of variations of
transport channel used or SRB bitrate. The maximum value is used as the value of
the AM RLC timers Timer_Poll, Timer_poll_periodic, Timer_status_periodic, and
Timer_RST in accordance to their activation with the appropriate "AM RLC status
report triggers" parameters. The values of the timers are configured as such to the
RLC entity of the RNC. The values of the timers are signalled to the RLC entity of
the UE rounded up to the closest value or down to the maximum value allowed in
the RRC signalling.
Related features
Fast Cell_PCH Switching (optional)
1.1.17.14
AMRLCPeriodMaxHSSRB (AM RLC status period max for SRBs with
HS-RACH/HS-FACH)
Description
This parameter defines the maximum status reporting period of the AM RLC in
relation to the RLC round trip time for the UL/DL SRB data transfer when the signalling radio bearer is mapped to HS-RACH in UL and HS-FACH in DL on on
CELL_FACH state (UL SRB using E-DCH transport channel and DL SRB using HSDSCH transport channel). The maximum value is used as the value of the AM RLC
timers Timer_Poll, Timer_poll_periodic, Timer_status_periodic, and Timer_MRW
and Timer_RST in accordance with their activations with the “AM RLC status report
triggers for SRB with FACH/RACH” parameter. The value is configured as such to
the RLC entity of the RNC. The value is signalled to the RLC entity of the UE
rounded up to the closest value or down to the maximum value allowed in the RRC
signalling.
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.15
AMRLCHSRACHPS/AMRLCHSRACHPSPeriodMin (AM RLC status
period min for PS NRT with HS-RACH)
Description
This parameter defines the minimum status reporting period of the AM RLC for the
PS radio bearers when data is transferred over HS-RACH on CELL_FACH state
using E-DCH transport channel. The value of the parameter is set to the AM RLC
timers Timer_Poll_Prohibit and Timer_Status_Prohibit in accordance with their activations with the "AM RLC status report triggers for PS NRT with HS-RACH" parameter. The value is configured as such to the RLC entity of the RNC. The value is
signalled to the RLC entity of the UE rounded up to the closest value or down to the
maximum value allowed in the RRC signalling.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
229
Summary of changes
1.1.17.16
WCDMA Radio Network Configuration Parameters
AMRLCHSRACHPS/AMRLCHSRACHPSTriggers (AM RLC status
report triggers for PS NRT with HS-RACH)
Description
This enables to activate and deactivate the polling and status reporting triggers and
the RLC timers for the AM RLC entity of the PS RAB in HS-RACH on CELL_FACH
state using E-DCH transport channel in its data transfer direction. The following
triggers and timers and period definition methods are controlled with the parameter:
"Timer poll periodic" to set the timer for the timer-based polling,
"Timer status periodic" to set the timer for the timer-based status reporting,
"Timer poll" to set the timer for a sent poll,
"Timer poll prohibit" to set the timer for filtering out polls in the sender,
"Timer status" prohibit to set the timer for filtering out status reports in the
receiver,
"Poll PDU" to set the trigger polling every Poll_PDU PDU,
"Poll SDU" to set the trigger polling every Poll_SDU SDU,
"Poll window" to set the window-based polling trigger,
"Last transmission PDU poll" to set the polling trigger for the last AMD PDU
scheduled for the first transmission,
"Last retransmission PDU poll" to set the polling trigger for the last AMD PDU
scheduled for the retransmission,
"Missing PDU indicator" to set the receiver to detect the missing AMD PDUs,
"SDU discard after MaxDAT transmissions" to define statically whether the
SDU discard after MaxDAT retransmissions or No_discard after MaxDAT transmissions shall be used,
"In sequency delivery of SDUs in UE" to define whether the RLC entity of the
UE is to deliver the received SDUs upper layers in sequency regardless of the value
of the RAB attribute Delivery Order.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
1.1.17.17
AMRLCOnDCHSRB136OffSat (AM RLC timer offset for SRB13.6 with
satellite DCH)
Description
This parameter defines the offset value for the maximum status reporting period of
the AM SRB 13.6 kbps when the signalling is transferred in the DCH configuration
over the satellite Iub. Value of the parameter is added to the per-ms-value of the
management parameter “AM RLC status period max for SRB13.6 with DCH”.
Parameter is not applied when the satellite Iub is disabled with the management
parameter “Satellite Iub Usage”. The final values of the maximum status reporting
timers are configured as such to the RLC entity of the RNC. The values of the timers
are signalled to the RLC entity of the UE rounded up to the closest value or down
to the maximum value allowed in the RRC signalling.
When value is changed it is taken into account only for new connections.
Related features
Satellite Iub (optional)
230
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.17.18
Summary of changes
RLCConfOptionFPS (RLC Conf option switch for Fast Cell_PCH
Switching)
Description
RNC defines RLC parameters for new radio link based on the used service of the
UE during RRC state transition from CELL_PCH to CELL_DCH. If the RLC parameters defined for the new radio link are identical with the previous RLC configuration,
then RLC configuration does not need to change in UE or RNC RLC entity when
Fast Cell_PCH Switching functionality is applied. If Fast Cell_PCH Switching functionality is applied and the RLC parameters defined for the new radio link are not
identical with the previous RLC configuration, then there are two options. The first
option is that RLC parameter configuration is done in the legacy way. The second
option is that the existing RLC configuration is used during radio link setup and then
RLC parameters are reconfigured when UE is in cell_dch state. This parameter is
used to select the option.
This parameter is related to RNFC-FastPCHSwitchEnabled which is the feature
optionality parameter for Fast Cell_PCH Switching feature. Therefore RLCConfOptionFPS parameter is only relevant when corresponding feature optionality parameter (RNFC-FastPCHSwitchEnabled) is enabled
Related features
Fast Cell_PCH Switching (optional)
1.1.17.19
UMRLCPTTDiscardTime (UM RLC SDU discard time in UE for PTT)
Description
The parameter defines the SDU discard timer value for the UM RLC entity of the UE
for push to talk service. The value of the parameter is signaled as such to UE.
Discard time is applied in the uplink transmission.
With the default value of the parameter timer based SDU discard is not used
by the UE. This is selected as default, so that data would not be discarded too early
in setup cases (discard of setup data cause setup delay). After setup phase too low
or too high value can cause voice quality problems.
Related features
Optimised push to talk experience (optional)
1.1.18
1.1.18.1
RNTRM
ActivityFactorForHSPA/AfPTTDL (Activity Factor for PTT RAB in
Downlink)
Description
This parameter defines the activity factor for the PTT transport bearer Connection
Admission Control reservation in downlink direction. The activity factor value 1
means that the transport layer bit rates are not scaled for the CAC function. The
value 0.50 for example means that the average part of the logical CAC input values
is scaled to half of the default value. After parameter modification, the new parameter value is taken into use at next new transport bearer establishment. The existing
bearers’ logical CAC reservations are not modified.
This parameter is applied when PTT RAB is on HSPA or R99 DCH transport
channels.
Parent parameter
ActivityFactorForHSPA
DN00211177
Issue 12B
Id:0900d805809da32a
231
Summary of changes
Related features
1.1.18.2
WCDMA Radio Network Configuration Parameters
Transport Bearer Tuning (optional) AND Optimised push to talk experience
(optional)
ActivityFactorForHSPA/AfPTTUL (Activity Factor for PTT RAB in
Uplink)
Description
This parameter defines the activity factor for the PTT transport bearer Connection
Admission Control reservation in uplink direction. The activity factor value 1 means
that the transport layer bit rates are not scaled for the CAC function. The value 0.50
for example means that the average part of the logical CAC input values is scaled
to half of the default value. After parameter modification, the new parameter value
is taken into use at next new transport bearer establishment. The existing bearers’
logical CAC reservations are not modified.
This parameter is applied when PTT RAB is on HSPA or R99 DCH transport
channels.
Parent parameter
ActivityFactorForHSPA
Related features
Transport Bearer Tuning (optional) AND Optimised push to talk experience
(optional)
1.1.18.3
DSCPBTSOMToBTS (DSCP for BTS OM towards BTS)
Description
This parameter specifies the Differentiated Services Code Point (DSCP) for BTS
O&M messages towards BTS. The DSCP value is used in IP packet to define PerHop-Behaviour.
Related features
IP Based Iub for Flexi WCDMA BTS (optional) OR Dual Iub for Flexi WCDMA BTS
(optional)
1.1.18.4
DSCPBTSOMToOMS (DSCP for BTS OM towards OMS)
Description
This parameter specifies the Differentiated Services Code Point (DSCP) for BTS
O&M messages towards OMS. The DSCP value is used in IP packet to define PerHop-Behaviour.
Related features
IP Based Iub for Flexi WCDMA BTS (optional) OR Dual Iub for Flexi WCDMA BTS
(optional)
1.1.18.5
Description
232
DSCPForGTPSignalling (DSCP for GTP signalling)
This parameter specifies the Differentiated Services Code Point (DSCP) for GTP
signalling traffic. The DSCP value is used in IP packet to define Per-Hop-Behaviour.
The configured DSCP value is applied also for GTP ECHO REQUEST messages. The GTP ECHO functionality is activated for the Iu-PS interface with attribute
RNTRM - EchoRequestSending.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.18.6
Description
Summary of changes
RespSyncModEnableIP (IP Iub DCH Sync Modifiable)
This parameter enables the modification of IP Iub Synchronization.
1.1.18.7
Description
RespSyncTimerIP (IP Response synchronization timer for DL synch
frame)
If no response from BTS has been received to DL synchronization control frame
within time interval defined by RespSyncTimerIP, a new DL synchronization control
frame will be sent. The number of retransmission is defined in RespSyncCounterIP,
which is set upon creation of the FP entity.
Overall IP transport synchronization period is defined by RespSyncTimerIP and
RespSyncCounterIP parameters.
1.1.18.8
RespSyncTimerSatIP (IP Response synchronization timer with Satellite Iub)
Description
If no response from BTS has been received to DL synchronization control frame
within time interval defined by RespSyncTimerSatIP, a new DL synchronization
control frame will be sent. The number of retransmission is defined in RespSyncCounterIP, which is set upon creation of the FP entity.
Overall IP transport synchronization period is defined by RespSyncTimerSatIP
and RespSyncCounterIP parameters.
Related features
Satellite Iub (optional)
1.1.18.9
Description
RespSyncCounterIP (Response synchronization counter for DL
synch frame)
Defines the number how often DL synchronization frame can be resent upon one
transport channel synchronization procedure for IP transport. Overall IP transport
synchronization period is defined by RespSyncTimerIP, RespSyncCounterIP
(RespSyncTimerSatIP and RespSyncCounterIP if Satelite Iub is enabled) parameters.
1.1.19
1.1.19.1
VCEL
DirectSCCEnabled (Direct SCC Enabled)
Description
This parameter determines if a serving HS-DSCH cell change procedure can be
started during anchoring immediately after the intra-frequency measurement event
1A or 1C triggered ASU procedure without waiting a new measurement report to
trigger the serving HS-DSCH cell change.
A new measurement report is required to trigger the serving HS-DSCH cell
change during anchoring if the value of this parameter is "Disabled".
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
233
Summary of changes
WCDMA Radio Network Configuration Parameters
1.1.19.2
FastActOfTargetServCell (Faster Activation Of Target Serving Cell)
Description
This parameter indicates whether the Faster Activation of Target Serving Cell functionality is enabled in the cell during anchoring.
When enabled in the cell, this functionality introduces faster activation of target
serving cell by applying HSPA SCC specific ATO values, see VCEL parameter
HSPASCCSpecificATO. HSPA SCC specific ATO (Activation Time Offset) value is
applied, when SCC is performed with RRC: RADIO BEARER RECONFIGURATION message, DL SRB is mapped to DCH and Delay Restriction Flag IE is used
(see parameter FastCompletionOfSCC). HSPA SCC specific ATO value enables
setting SCC activation time even more aggressive, without impacting other procedures.
The formula to calculate the absolute CFN with this new ATO value is the following:
Absolute CFN = AT - HSPASCCSpecificATO
where AT = the activation time, which RNC has produced internally for a synchronised radio link handling procedure. About AT calculation, see parameter
RNPS- ActivationTimeOffset.
The Faster Activation of Target Serving Cell is not applied if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.19.3
FastCompletionOfSCC (Faster Completion of SCC Procedure)
Description
This parameter indicates whether the Faster Completion of SCC Procedure functionality is enabled in the cell during anchoring.
When enabled in the cell, this functionality introduces faster completion of SCC
procedure by including the Delay Restriction Flag IE in RRC: RADIO BEARER
RECONFIGURATION message. Inclusion is done on condition that RL is not reconfigured during SCC and UE is rel6 or newer. The included IE indicates that UE shall
send RRC: RADIO BEARER RECONFIGURATION COMPLETE message as soon
as possible without waiting CFN to elapse, but still perform the serving cell change
based on received CFN.
The Faster Completion of SCC Procedure is not applied if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.19.4
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH)
Description
This parameter identifies the measurement control parameter set (FMCS object)
controlling the intra-frequency measurements of a user having standalone SRB
allocated on DCH during anchoring.
If the value of this parameter is "Not defined", the VCEL parameter RtFmcsIdentifier identifies the FMCS parameter set for standalone SRB during anchoring.
Related features
I-BTS Sharing (optional) AND Fast HSPA Mobility (optional)
234
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.19.5
Summary of changes
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay)
Description
This parameter determines how much the HS-DPCCH power offset update is
delayed after the active set update during anchoring. The delay enables that serving
HS-DSCH cell change (or the next active set update) can be executed immediately
after the previous active set update without waiting for the HS-DPCCH power offset
update procedure to complete.
Recommended value is 3000 ms. The HS-DPCCH power offset update is not
delayed during anchoring if the value of this parameter is 0 ms.
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.19.6
HSPASCCSpecificATO (HSPA SCC Specific ATO Value)
Description
This parameter indicates the range of the HSPASCCSpecificATO parameter during
anchoring. Range is from 0 ms to 300 ms with a step of 10 ms. Default value of the
parameter is 100 ms.
If too high value is applied, timing of synchronized SCC procedure is jeopardised.
If too low value is applied, synchronized SCC procedure is delayed.
The HSPASCCSpecificATO is not applied if either the value of VCEL parameter
FastActOfTargetServCell is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.19.7
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation)
Description
This parameter indicates whether the Power Offset Update Message Size Optimisation functionality is enabled in the cell during anchoring.
When enabled in the cell, this functionality introduces message size optimisation for RRC: PHYSICAL CHANNEL RECONFIGURATION message, which is used
to update HS-DPCCH power offsets. Unnecessary IEs (namely Downlink information common for all radio links IE and Downlink information per radio link list IE) are
omitted resulting that message size is reduced. In some cases it will reduce from 2
to 1 TB (Transport Block). Message size reduction leads to faster and more reliable
signaling.
The Power Offset Update message size is not optimised if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
Fast HSPA Mobility (optional) AND HSPA Inter-RNC Cell Change (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
235
Summary of changes
1.1.19.8
WCDMA Radio Network Configuration Parameters
SRBHopsIdentifier (SRB HOPS Identifier)
Description
This parameter identifies the parameter set (HOPS object) controlling the intra-frequency handovers of a user having standalone SRB allocated on DCH during
anchoring.
If the value of this parameter is "Not defined", the VCEL parameter RtHopsIdentifier identifies the HOPS parameter set for standalone SRB during anchoring.
Related features
I-BTS Sharing (optional) AND Fast HSPA Mobility (optional)
1.1.19.9
Description
WACSetIdentifier (WAC Parameter Set Identifier)
Pointer to the WAC object identifier. Defines the WAC parameter set to be used in
this Virtual cell.
1.1.20
1.1.20.1
WAC
InactHSRACH (Inactive HS-RACH capable UE)
Description
The parameter defines how long inactive HS-RACH capable UE is kept in Cell_DCH
state after time to triggers for HSDPA low utilization and E-DCH low throughput
have triggered when the HS-RACH is configured in the main cell of the UE active
set cells. The main cell is the cell having best CPICH EcNo value reported by the
UE.
When low utilization is detected for HSDPA MAC-d flow (MACdflowutilTimetoTrigger) and low throughput for E-DCH MAC-d flow (EDCHMACdFlowThroughputTimetoTrigger), the RB can be released. When this has happened to all the RBs
of the user, the user can be transferred to Cell_FACH state. Instead of state transition the user can be kept longer in the Cell_DCH state. This timer defines how much
longer the user can be kept in Cell_DCH state even if it is inactive all the period.
This timer is applicable only if UE is HS-RACH capable and the HS-RACH has
been configured in the "main cell" of the active set of the UE.
Note special value '255': UE capability of HS-RACH is not taken into account,
that is this timer is not used.
Related features
High speed Cell_FACH Uplink (optional)
1.1.20.2
Description
This parameter defines the origin of the last configuration action affecting the object.
1.1.20.3
Description
236
WACChangeOrigin (WAC Change origin)
WACId (WAC Identifier)
Identifies the WAC object instance uniquely. The default parameter set is in the
WAC object instance with WACId=1.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.21
1.1.21.1
Summary of changes
WBTS
RRMULDCHActivityFactor/RRMULActivityFactorPTT (Average
relative UL data rate for RBs of PTT)
Description
The parameter defines the average UL data rate in relation to its maximum allocated
transport channel data rate for the RB of the PTT RAB.
Too small value can drive a cell to overload, because too many PTT users
are admitted. Too big value causes extra congestion for the PTT service.
Parent parameter
RRMULDCHActivityFactor
Related features
Optimised push to talk experience (optional)
1.1.21.2
PWSMEnableWakeUpTime (Enable cell activation based on time of
day)
Description
This parameter defines whether a non-remaining cell that was previously shut down
becomes active regardless of the traffic when the shutdown time limit ends. The end
of the shutdown time limit is controlled by the following parameters:
WBTS – PWSMShutdownEndHour,
WBTS – PWSMShutdownEndMin
Related features
Power Saving Mode for BTS (optional)
1.1.21.3
HSUPACCEnabled (HSUPA Congestion Control activation)
Description
This parameter enables the HSUPA Congestion Control for applicable E-DCH
bearers regardless of the TTI value. If the parameter value is set to Enabled, the
HSUPA congestion control is activated. When it is set to Disabled, there will not be
any HSUPA congestion control handling in the RNC for the BTS in concern. If
parameter is modified online it will not have effect on the existing bearers but new
value will be taken into account for the new establishments.
HSUPA Congestion Control functionality is enabled by default for the BTSs that
has HSUPA activated cells.
In case the HSPA QoS Aware scheduling is activated for any of the cells of the
BTS then Iub Transport QoS license is required for activating the HSUPA congestion control. In respect of the parameter values and licenses it means that whenever
both WCEL-HSPAQoSEnabled and WBTS-HSUPACCEnabled are activated at the
same time for the given BTS the license combination “HSDPA Congestion Control
(optional) AND QoS Aware HSPA Scheduling (optional) AND Iub Transport QoS
(optional)” is required.
Related features
HSUPA Congestion Control (standard) AND HSUPA (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
237
Summary of changes
1.1.21.4
WCDMA Radio Network Configuration Parameters
IPBasedRouteIdIub3 (IP Based Route Id Iub 3)
Description
The IPBasedRouteIdIub refers to the logical IP Based Route entity configured in the
IP layer with MML or IP Plan interface. The IP Based Route configured for the Iub
interface is used for the user plane connections towards the BTS controlling the
interface unit and port selection along with the source IP address and UDP port
selection. This parameter is applied when the IP over Ethernet transport option is
used.
With Iub Transport Solution for Network Sharing feature operator may define
additional IP Based Route references for user plane traffic. With different IP Based
Route identifiers user plane bearers with certain CN PLMN id can be assigned to
specific transport resource.
Note: The first IP Based Route identifier (WBTS - IPBasedRouteId) is selected
for the setup when the PLMN id is not known or when the referred IP Based Route
Id attribute has unspecified value.
Related features
IP Based Iub for Flexi WCDMA BTS (optional) AND ( Multi-Operator Core Network
(optional) OR Multioperator RAN (optional) )
1.1.21.5
IPBasedRouteIdIub4 (IP Based Route Id Iub 4)
Description
The IPBasedRouteIdIub refers to the logical IP Based Route entity configured in the
IP layer with MML or IP Plan interface. The IP Based Route configured for the Iub
interface is used for the user plane connections towards the BTS controlling the
interface unit and port selection along with the source IP address and UDP port
selection. This parameter is applied when the IP over Ethernet transport option is
used.
With Iub Transport Solution for Network Sharing feature operator may define
additional IP Based Route references for user plane traffic. With different IP Based
Route identifiers user plane bearers with certain CN PLMN id can be assigned to
specific transport resource.
Note: The first IP Based Route identifier (WBTS - IPBasedRouteId) is selected
for the setup when the PLMN id is not known or when the referred IP Based Route
Id attribute has unspecified value.
Related features
IP Based Iub for Flexi WCDMA BTS (optional) AND ( Multi-Operator Core Network
(optional) OR Multioperator RAN (optional) )
1.1.21.6
IubTransportSharing (Iub Transport Sharing activation)
Description
This attribute enables or disables the Iub Transport Sharing functionality for the
given BTS. With Iub Transport Solution for Network Sharing feature operator may
define PLMN id specific transport resource and transport priority allocation. PLMN
id specific transport resource index is defined with IUO - IubTransportSharingInd
parameter.
Related features
Multi-Operator Core Network (optional) OR Multioperator RAN (optional)
238
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.21.7
Summary of changes
MaxFPDLFrameSizeIub (Maximum FP downlink frame size Iub)
Description
The user plane frame size can be limited with this parameter in order to avoid IP
layer fragmentation. The RNC takes the value into account at DL User Plane traffic
processing and limits the maximum HS-DSCH FP frame size accordingly. The
value has to be planned according to the minimum IP layer MTU along the path to
the BTS. The IP and UDP header overheads have to be subtracted from the IP interface MTU value (e.g. IPv4 IP header 20 bytes, UDP header 8 bytes) when adjusting
the value since the parameter directly controls the user plane FP frame size.
Part of the BTS variants cannot handle bigger than 1428 FP frames. RNC keeps
the maximum FP frame size always limited to 1428 and additionally obeys parameter values configured to lower than 1428.
Related features
IP Based Iub for Flexi WCDMA BTS (optional) OR IP Based Iub for UltraSite
WCDMA BTS (optional)
1.1.21.8
TQMId2 (TQM Object Identifier 2)
Description
The TQM identification gives the reference to the TQM object (Transport QoS
Mapping) used for the WBTS. The TQM object defines the transport bearer prioritization mapping based on the air interface channel type and the radio network layer
scheduling priority.
If the TQM is not related to the WBTS then the basic RT/NRT DSCP mapping
is applied according to the DSCP definitions in the WBTS object.
With Iub Transport Solution for Network Sharing feature operator may define
additional TQM instance references for user plane traffic. With PLMN id specific
TQM configuration different DSCP allocation schemes can be implemented in
between the operators.
Note: The first TQM object identifier (WBTS - TQMId) is selected for the setup
when the PLMN id is not known or when the referred TQMId attribute has unspecified value.
Related features
Iub Transport QoS (optional) AND ( Multi-Operator Core Network (optional) OR
Multioperator RAN (optional) )
DN00211177
Issue 12B
Id:0900d805809da32a
239
Summary of changes
1.1.21.9
WCDMA Radio Network Configuration Parameters
TQMId3 (TQM Object Identifier 3)
Description
The TQM identification gives the reference to the TQM object (Transport QoS
Mapping) used for the WBTS. The TQM object defines the transport bearer prioritization mapping based on the air interface channel type and the radio network layer
scheduling priority.
If the TQM is not related to the WBTS then the basic RT/NRT DSCP mapping
is applied according to the DSCP definitions in the WBTS object.
With Iub Transport Solution for Network Sharing feature operator may define
additional TQM instance references for user plane traffic. With PLMN id specific
TQM configuration different DSCP allocation schemes can be implemented in
between the operators.
Note: The first TQM object identifier (WBTS - TQMId) is selected for the setup
when the PLMN id is not known or when the referred TQMId attribute is has unspecified value.
Related features
Iub Transport QoS (optional) AND ( Multi-Operator Core Network (optional) OR
Multioperator RAN (optional) )
1.1.21.10
TQMId4 (TQM Object Identifier 4)
Description
The TQM identification gives the reference to the TQM object (Transport QoS
Mapping) used for the WBTS. The TQM object defines the transport bearer prioritization mapping based on the air interface channel type and the radio network layer
scheduling priority.
If the TQM is not related to the WBTS then the basic RT/NRT DSCP mapping
is applied according to the DSCP definitions in the WBTS object.
With Iub Transport Solution for Network Sharing feature operator may define
additional TQM instance references for user plane traffic. With PLMN id specific
TQM configuration different DSCP allocation schemes can be implemented in
between the operators.
Note: The first TQM object identifier (WBTS - TQMId) is selected for the setup
when the PLMN id is not known or when the referred TQMId attribute is has unspecified value.
Related features
Iub Transport QoS (optional) AND ( Multi-Operator Core Network (optional) OR
Multioperator RAN (optional) )
240
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.21.11
Summary of changes
PWSMAVTrafficVERLogic (Traffic verification logic in PWSM cell
activation process)
Description
This parameter defines the traffic verification logic in PWSM cell activation process
of non-remaining cells.
When the value of the parameter is set to “All criteria”, all criteria for different
RB types have to be fulfilled to initiate the cell activation. When the value of this
parameter is set to “At least one criterion”, at least one criterion for one RB type has
to be fulfilled to initiate the cell activation. When the value of this parameter is set to
“RT and NRT HSDPA power or any other criteria”, either the criteria for both RT and
NRT HSDPA power have to be fulfilled or any other criteria for any RB type have to
be fulfilled to initiate the cell activation.
Related features
Power Saving Mode for BTS (optional)
1.1.21.12
Description
WBTSSWBuildId (WBTS SW build identifier)
This parameter indicates the BTS SW build version information. RNC gets the
parameter value from BTS NE.
1.1.22
1.1.22.1
WCEL
HSRACHTransmisBackOff (Additional E-DCH transmission back off
for HS-RACH)
Description
This parameter determines the Additional E-DCH transmission back off for HSRACH. The time has been defined as the terms of TTIs. For DTCH/DCCH transmissions, the UE calculates maximum period for collision resolution phase from the
allowed start time of the E-DCH transmission. With E-TTI=10ms the allowed start
time of the E-DCH transmission is 1 + "Additional E-DCH transmission back off"
after start of the DPCCH transmission.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.2
AppAwareRANCapability (Application Aware RAN Capability)
Description
This parameter defines the Application Aware RAN capability of the local cell.
Related features
Application Aware RAN (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
241
Summary of changes
1.1.22.3
WCDMA Radio Network Configuration Parameters
AppAwareRANEnabled (Application Aware RAN Enabled)
Description
This parameter defines whether the feature Application Aware RAN is enabled or
not in the cell. The following functionalities can be activated/deactivated with this
parameter:
•dynamic service or application prioritization for the HSDPA scheduling
•dynamic demotion of UL bulk traffic
Prioritization can be done between bearers each carrying multiple services.
This parameter value is checked only for the serving HSDPA cell.
Related features
Application Aware RAN (optional)
1.1.22.4
AutoACResULOLThr (Automatic Access Class Restriction Uplink
Overload Threshold)
Description
This parameter defines the threshold for the UL interference load to start barring
access classes. The parameter defines the offset from the planned target level PrxTarget in case of non-HSPA cell and PrxMaxTargetBTS for HSPA configured cell.
Low offset value is used in case of non-HSPA cell and high offset value for
HSPA configured cell.
Related features
Automatic access class restriction (optional)
1.1.22.5
AutoACRPrxTotalAvgWs (Automatic Access Class window size for
averaging PrxTotal)
Description
This parameter defines the window size for arithmetical averaging of PrxTotal measurement results. The parameter defines window size in terms of number of
samples of PrxTotal. The averaged value is used by Cell specific load control to
estimate overload situation in a cell. Detected overload can trigger restriction of
access classes in the cell. The higher the value is the higher is averaging and vice
versa.
Related features
Automatic access class restriction (optional)
1.1.22.6
HSRACHSubChannelNumber (Available Sub Channel Number for
HS-RACH)
Description
This parameter determines the avaliable sub channel numbers used with HSRACH. When the HS-RACH is used, the information is signaled to UEs via
RRC:SIB5/5bis. Each bit indicates availability for a subchannel, where the subchannels are numbered "subchannel 0" to "subchannel 11". The value 1 of a bit indicates
that the corresponding subchannel is available and the value 0 indicates that it is
not available.
When the value ‘0000 0000 0000’ is set, the value is same than indicated in
the IE “Available Sub Channel Number” in the IE “PRACH system information list”
and defined by AllowedRACHSubChannels parameter.
Related features
High speed Cell_FACH Uplink (optional)
242
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.7
Summary of changes
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No)
Description
This parameter determines the averaging window for the periodical CPICH Ec/No
measurement reporting, which is used as a criterion for the serving HS-DSCH cell
change procedure. Averaging is executed in the RNC.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNMOBI
(RNC level) parameter HSDPACPICHAveWindow determines the averaging
window for the periodical CPICH Ec/No measurement reporting.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.22.8
CodeTreeOptimisationGuardTime (Code Tree Optimisation Guard
Time)
Description
This parameter determines how long a DPCH must be allocated before it can be
reconfigured to a better position in the code tree.
The guard time secures that a serving HS-DSCH cell change or active set
update procedure can be executed immediately after the DPCH allocation without
waiting for the code tree optimisation procedure to complete. Recommended value
is 3 seconds in cells which are serving high mobility UEs.
The guard time is not used if either the value of this parameter is 0 s or the
value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
Fast HSPA Mobility (optional)
1.1.22.9
HSRACHImplicitRelease (Common E-DCH implicit release for HSRACH)
Description
This parameter determines the use of Common E-DCH implicit release indicator.
The value other than infinity means that implicit release is in use and the value is
directly set in the "E-DCH transmission continuation back off" IE of SIB5/5bis when
the HS-RACH is used in the cell. Infinity means that implicit release is not in use and
other values that implicit release is in use.
Related features
High speed Cell_FACH Uplink (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
243
Summary of changes
1.1.22.10
WCDMA Radio Network Configuration Parameters
HSDPAServCellWindow (CPICH Ec/No window for serving HSDSCH cell)
Description
This parameter determines the maximum allowed difference between the CPICH
Ec/No of the best active set cell and the CPICH Ec/No of the serving HS-DSCH cell.
If the difference between the averaged CPICH Ec/No values exceeds the value of
this parameter, serving HS-DSCH cell change procedure is initiated.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNMOBI
(RNC level) parameter HSDPAServCellWindow determines the maximum allowed
difference between the best active set cell and the serving HS-DSCH cell.
The WCEL parameters HSDPACPICHReportPeriod and HSDPACPICHAveWindow (or the corresponding RNMOBI parameters) determine the
reporting period of the periodical intra-frequency CPICH Ec/No measurement,
which is used as a criterion for the serving HS-DSCH cell change procedure, and
the averaging window for the periodical CPICH Ec/No measurement reports
respectively.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.22.11
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH
cell selection)
Description
This parameter determines the maximum allowed difference between the CPICH
Ec/No of the best active set cell and the CPICH Ec/No of the serving HS-DSCH cell
when SRBs are mapped on E-DCH/HS-DSCH. If the difference between the
averaged CPICH Ec/No values exceeds the value of this parameter, serving HSDSCH cell change procedure is initiated. If the serving HS-DSCH cell change fails,
SRBs are switched to E-DCH/DCH or DCH/DCH configuration.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNHSPA
(RNC level) parameter HSDPASRBWindow determines the maximum allowed difference between the best active set cell and the serving HS-DSCH cell.
The WCEL parameters HSDPACPICHReportPeriod and HSDPACPICHAveWindow (or the corresponding RNMOBI parameters) determine the
reporting period of the periodical intra-frequency CPICH Ec/No measurement,
which is used as a criterion for the serving HS-DSCH cell change procedure, and
the averaging window for the periodical CPICH Ec/No measurement reports
respectively.
Related features
Fractional DPCH (optional) AND Fast HSPA Mobility (optional)
244
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.12
Summary of changes
DefMeasCtrlReading (Deferred Measurement Control Reading)
Description
This parameter indicates whether the Deferred Measurement Control Reading functionality is enabled in the cell.
When enabled in the cell, this functionality introduces faster RACH access for
Rel-7 and newer UEs by including the Deferred measurement control reading
support IE in SIB3. The included IE indicates to UE that reading of SIB11, SIB11bis
and SIB12 can be skipped before RACH access. This means that UE can send
RRC CONNECTION REQUEST, CELL UPDATE or URA UPDATE without reading
first the above mentioned SIBs.
This functionality speeds up setup times after cell selection/re-selection and
the gain depends on SIB contents and scheduling.
The Deferred Measurement Control Reading is not applied if either the value
of this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
Fast HSPA Mobility (optional)
1.1.22.13
DirectSCCEnabled (Direct SCC Enabled)
Description
This parameter determines if a serving HS-DSCH cell change procedure can be
started immediately after the intra-frequency measurement event 1A or 1C triggered ASU procedure without waiting a new measurement report to trigger the
serving HS-DSCH cell change.
A new measurement report is required to trigger the serving HS-DSCH cell
change if either the value of this parameter or the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.22.14
DRXCycleHSFACH (Discontinuous Reception Cycle HS-FACH)
Description
This parameter indicates the length of the DRX Cycle during DRX operation in High
Speed CELL_FACH.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.15
HSFACHVolThrDLPTT (DL traffic volume measurement threshold of
HS-FACH for PTT)
Description
The parameter defines, in bits, the threshold of data in the RLC buffers of PTT RB
that triggers the downlink traffic volume measurement report (capacity request) on
MAC, when UE is able to use HS-DSCH in Cell_FACH state in DL.
Below the threshold, RNC sends data on HS-FACH and UE is not moved to
Cell_DCH state.
Too low value of this parameter causes waisting of dedicated resources, delay
and signaling load, because UE is moved to Cell_DCH sate too easily.
Too high value of this parameter causes loading of common channels.
Related features
Optimised push to talk experience (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
245
Summary of changes
1.1.22.16
WCDMA Radio Network Configuration Parameters
SmartTrafVolThrDL (DL traffic volume threshold for Smartphone)
Description
The parameter defines, in bytes, the threshold of data in the RLC buffers of SRB3,
SRB4 and all NRT RBs that trigger the downlink traffic volume measurement report
(capacity request) on MAC, when UE is in Cell_FACH state. Otherwise, RNC sends
data on FACH. The parameter is used for the identified Smartphone instead of the
TrafVolThresholdDLLow parameter.
Related features
Fast Dormancy Profiling (optional)
1.1.22.17
AutoACDSACRestriction (Domain Specific Access Class Restriction)
Description
This parameter defines the particular CN domain (CS domain, PS domain, or both)
and the Cell Access Restriction for which the Access Classes (ACs) are restricted
from accessing the radio network in the cell. The parameter can be set to the following values:
Restrict CS and PS domain: Rel-6 or newer UE is restricted from accessing the
RAN for both CS and PS domains for all the ACs that are in the CN domain AC
barred list in that cell.
Restrict PS Domain: Rel-6 or newer UE is restricted from accessing the RAN
for the PS domain for all the ACs in the CN domain-specific AC barred list in that
cell.
Restrict CS Domain: Rel-6 or newer UE is restricted from accessing the RAN
for the CS domain for all the ACs in the CN domain-specific AC barred list in that
cell.
Restrict PS Domain and Cell Access: Rel-6 or newer UE is restricted from
accessing the RAN for the PS domain for all the ACs in the AC barred list that is CN
domain-specific in that cell. Also, the Rel-5 or older UEs are restricted from accessing the RAN for all the ACs in the Access Class Barred List in that cell.
Restrict CS Domain and Cell Access: Rel-6 or newer UEs are restricted from
accessing the RAN for the CS domain for all the ACs in the CN domain-specific AC
barred list in that cell. Also, the Rel-5 or older UEs are restricted from accessing the
RAN for all the ACs in the Access Class Barred List in that cell.
Restrict CS and PS domain and Cell Access: Rel-6 or newer UE is restricted
from accessing the RAN for both CS and PS domains for all the ACs in the CN
domain-specific AC barred lists. Also, the Rel-5 or older UEs are restricted from
accessing the RAN for all the ACs in the Access Class Barred List in that cell.
Cell Access Restriction: All the UEs, regardless of their release versions, are
restricted from accessing the RAN (regardless of their CN domain) for all the ACs
in the Access Class Barred List in that cell.
Related features
Automatic access class restriction (optional)
1.1.22.18
DRXInterruptHSDSCHData (DRX Interruption by HS-DSCH data)
Description
This parameter indicates whether DRX operation in High Speed CELL_FACH can
be interrupted by HS-DSCH data or not.
Related features
High speed Cell_FACH Uplink (optional)
246
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.19
Summary of changes
DBandHSDPAEnabled (Dual Band HSDPA Enabled)
Description
Parameter enables / disables the Dual Band Dual Cell HSDPA (DB-DC-HSDPA)
usage in the cell. Dual Cell HSDPA (DC-HSDPA) must be enabled in the DB-DCHSDPA cell.
DB-DC-HSDPA cannot be used simultaneously with MIMO for the UE. DB-DCHSDPA with the single cell HSUPA can be activated for the UE. MIMO configuration
is not specifically restricted in the DB-DC-HSDPA cell but MIMO can be used irrespective of the DB-DC-HSDPA configuration in the cell.
NOTE: DB-DC-HSDPA cell pair must be configured in the frequency bands,
which support Dual Band HSDPA operation. System supported DL band combinations are: I&VIII, II&IV or I&V.
Related features
Dual-Cell HSDPA 42Mbps (optional) AND Dual Band HSDPA 42 Mbps (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
247
Summary of changes
1.1.22.20
WCDMA Radio Network Configuration Parameters
FastHSPAMobilityEnabled (Fast HSPA Mobility Enabled)
Description
This parameter indicates whether or not the Fast HSPA Mobility feature is enabled
in the cell. Before the feature is enabled in the cell, the system checks that the
maximum amount of Fast HSPA Mobility -capable cells does not exceeded the limit
set by the capacity license.
When the Fast HSPA Mobility feature is enabled in the cell, it is possible to
make use of the following parameters:
- WCEL - ActivationTimeOffset
- WCEL - ATOSRBsOnHSPA
- WCEL - SRBDCHFmcsId
- WCEL - SRBHSPAFmcsId
- VCEL - SRBDCHFmcsId
- ADJS - SRBHopsIdentifier
- ADJD - AdjdSRBHopsId
- VCEL - SRBHopsIdentifier
- WCEL - HSDPAMaxCellChangeRepetition
- WCEL - HSDPASRBWindow
- WCEL - HSDPACPICHReportPeriod
- WCEL - HSDPACPICHAveWindow
- WCEL - HSDPAServCellWindow
- WCEL - HSDPACellChangeMinInterval
- WCEL - FastCompletionOfSCC
- VCEL - FastCompletionOfSCC
- WCEL - HSPASCCSpecificATO
- VCEL - HSPASCCSpecificATO
- WCEL - FastActOfTargetServCell
- VCEL - FastActOfTargetServCell
- WCEL - PowerOffsetUpdMsgSize
- VCEL - PowerOffsetUpdMsgSize
- WCEL - HSPwrOffsetUpdateDelay
- VCEL - HSPwrOffsetUpdateDelay
- WCEL - DirectSCCEnabled
- VCEL - DirectSCCEnabled
- RNC - RRCConnSetupMsgSize
- WCEL - DefMeasCtrlReading
- WCEL - CodeTreeOptimisationGuardTime
Related features
Fast HSPA Mobility (optional)
248
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.21
Summary of changes
FastActOfTargetServCell (Faster Activation Of Target Serving Cell)
Description
This parameter indicates whether the Faster Activation of Target Serving Cell functionality is enabled in the cell.
When enabled in the cell, this functionality introduces faster activation of target
serving cell by applying HSPA SCC specific ATO values, see WCEL parameter
HSPASCCSpecificATO. HSPA SCC specific ATO (Activation Time Offset) value is
applied, when SCC is performed with RRC: RADIO BEARER RECONFIGURATION message, DL SRB is mapped to DCH and Delay Restriction Flag IE is used
(see parameter FastCompletionOfSCC). HSPA SCC specific ATO value enables
setting SCC activation time even more aggressive, without impacting other procedures. When applied, HSPASCCSpecificATO overrides other cell level ATO parameters during SCC.
The formula to calculate the absolute CFN with this new ATO value is the following:
Absolute CFN = AT - HSPASCCSpecificATO
where AT = the activation time, which RNC has produced internally for a synchronised radio link handling procedure. About AT calculation, see parameter
RNPS- ActivationTimeOffset.
The Faster Activation of Target Serving Cell is not applied if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.22.22
FastCompletionOfSCC (Faster Completion of SCC Procedure)
Description
This parameter indicates whether the Faster Completion of SCC Procedure functionality is enabled in the cell.
When enabled in the cell, this functionality introduces faster completion of SCC
procedure by including the Delay Restriction Flag IE in RRC: RADIO BEARER
RECONFIGURATION message. Inclusion is done on condition that RL is not reconfigured during SCC and UE is rel6 or newer. The included IE indicates that UE shall
send RRC: RADIO BEARER RECONFIGURATION COMPLETE message as soon
as possible without waiting CFN to elapse, but still perform the serving cell change
based on received CFN.
The Faster Completion of SCC Procedure is not applied if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
249
Summary of changes
1.1.22.23
WCDMA Radio Network Configuration Parameters
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH)
Description
This parameter identifies the measurement control parameter set (FMCS object)
controlling the intra-frequency measurements of a user having standalone SRB
allocated on DCH.
If the value of this parameter is "Not defined" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled", the WCEL parameter RtFmcsIdentifier identifies the FMCS parameter set for standalone SRB on DCH.
Related features
Fast HSPA Mobility (optional)
1.1.22.24
SRBHSPAFmcsId (FMCS identifier for standalone SRB on HSPA)
Description
This parameter identifies the measurement control parameter set (FMCS object)
controlling the intra-frequency measurements of a user having standalone SRB
allocated on HSPA.
If the value of this parameter is "Not defined" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled", the WCEL parameter HSPAFmcsIdentifier identifies the FMCS parameter set for standalone SRB on HSPA.
Related features
Fractional DPCH (optional) AND Fast HSPA Mobility (optional)
1.1.22.25
HappyBitDelayConHSRACH (Happy bit delay condition for HSRACH)
Description
This parameter determines the value for the Happy bit delay condition information
element for HS-RACH. The information element is signalled to the UE using the
RRC:SIB/5bis message for the UEs on CELL_FACH state using HS-RACH. The UE
utilises information for setting the E-DCH related happy bit. The happy bit is signalled to the BTS in E-DPCCH.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.26
T321 (High Speed Cell FACH DRX operation timer)
Description
This parameter indicates the time the UE waits until initiating DRX operation in High
Speed CELL_FACH. UE enters HS-DSCH DRX cycle after the expiry of this timer
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.27
HSFACHCapability (High Speed FACH Capability)
Description
Parameter indicates the high speed FACH capability of the cell.
Related features
High speed Cell_FACH DL (optional)
250
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.28
Summary of changes
HSRACHCapability (High Speed RACH Capability)
Description
Parameter indicates the high speed RACH capability of the cell. The cell is HSRACH capable, if the BTS informs itself to be Common E-DCH Capable, E-AI
Capable and ACK-NACK and CQI Capable.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.29
HSRACHEnabled (High Speed RACH Enabled)
Description
The parameter enables / disables the use of HS-RACH in UL in the cell, that is the
use of HSUPA in the cell for the UE on CELL_FACH state.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.30
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay)
Description
This parameter determines how much the HS-DPCCH power offset update is
delayed after the active set update. The delay enables that serving HS-DSCH cell
change (or the next active set update) can be executed immediately after the
previous active set update without waiting for the HS-DPCCH power offset update
procedure to complete.
Recommended value is 3000 ms in cells which are serving high mobility UEs.
The HS-DPCCH power offset update is not delayed if either the value of this parameter is 0 ms or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.22.31
RXBurstHSFACH (HS-FACH Reception Burst)
Description
This parameter indicates the period within the DRX Cycle that the UE continuously
receives HS-DSCH.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.32
AmpliRatioOptHSRACH (HS-RACH amplitude ratio optimized for
low/high bit rate)
Description
This parameter determines the use of low or high bit rate optimised reference amplitude ratios of E-DPCH(s) relative to the amplitude ratio of DPCCH for certain ETFC(s) in case of HS-RACH.
Related features
High speed Cell_FACH Uplink (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
251
Summary of changes
1.1.22.33
WCDMA Radio Network Configuration Parameters
HSRACHMPO (HS-RACH Measurement Power Offset)
Description
This parameter defines the HSDPA Measurement Power Offset signaled to BTS
when the HS-RACH is setup in the cell. Measurement Power Offset defines the
default power offset between HS-PDSCH and P-CPICH.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.34
MEHHSDPAUserNbrCQI (HSDPA CQI user number for the Mass
Event Handler)
Description
The parameter determines the number of HSDPA users in the cell to trigger usage
of the increased CQI feedback cycle for the Mass Event Handler.
The increased CQI feedback value is valid for a user not using CPC. The value
for the temporary CQI feedback cycle to be used instead of the fixed 4 ms is defined
by the RNHSPA-MEHCQIFeedbackCycle parameter.
If the value 0 is set to the parameter, the increased CQI feedback cycle is used
for every HSDPA UE not using CPC.
The function is switched on/off by the WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
1.1.22.35
HSFACHRABDRAEnabled (HSFACH direct resource allocation for
NRT HSPA RAB)
Description
The parameter enables/disables the use of the direct dedicated resource allocation
for HSPA (parameter RABDRAEnabled) to CELL_DCH state in case of HS RACH
is supported by RNC and HS RACH Capable (Rel8) UE.
If the parameter is set as disabled (default), HS RACH capable (Rel8) UE is
kept in high speed common channels (HS-DSCH and E-DCH) on CELL_FACH
state.
If the parameter is set as enabled, dedicated resource allocation is tried for PS
data of interactive and background traffic classes during the NRT RAB setup phase
as described in parameter RABDRAEnabled.
0 (Disabled): High speed common channels are preferred for HS RACH
Capable (Rel8)UE on Cell_FACH state.
1 (Enabled): Direct dedicated resource allocation for HSPA can be applied for
HS RACH Capable (Rel8) UE on Cell_FACH state.
Related features
High speed Cell_FACH Uplink (optional)
252
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.36
Description
Summary of changes
HSFACHRel8ConSetupEC (HSFACH Rel8UE EstCause mapping in
RRC con setup)
This parameter defines the Establishment Cause (EC) values which prefer new high
speed common channels (HS FACH/HS RACH) usage for Rel8 UEs.
Establishment Cause is RRC information element which is received from the
UE in the RRC message RRC Connection Request.
The value 1 means that certain Establishment Cause prefers high speed
common channels in the RRC connection setup.
The value 0 means that certain Establishment Cause prefers SRB mapping to
the dedicated channel (DCH) or to the dedicated high speed packet access channel
(HSPA i.e. on HS-DSCH/E-DCH) in the RRC connection setup.
Bit 9: Emergency call does not effect, SRBs of emergency call are always
mapped to DCH in the RRC connection setup.
The parameter FDPCHSetup defines allocation procedure of the F-DPCH in
the RRC connection setup.
The parameter HSFACHRABDRAEnabled defines when direct resource allocation of the dedicated channels for HSPA for Rel8 UE is not allowed after RAB
setup comes.
Related features
1.1.22.37
Description
DN00211177
Issue 12B
High speed Cell_FACH Uplink (optional)
HSPA128UsersPerCell (HSPA 128 Users per Cell)
This parameter determines whether the “HSPA 128 users per cell“ feature is
enabled in the cell or not. If this feature is enabled, a maximum of 128 HSDPA and
128 serving HSUPA users can be admitted per cell, if BTS also supports 128 HSPA
users per cell (Rel2 baseband HW).
If this feature is not enabled, the RNC allows only 16, 48, 64 or 72 HSDPA
users per cell (see HSDPA48UsersEnabled, HSDPA64UsersEnabled,
HSPA72UsersPerCell) and only 3, 12, 60 users per BTS or LCG or 72 HSUPA
users per cell (see HSUPAXUsersEnabled, HSPA72UsersPerCell).
User amounts can also be restricted with the following parameters:
- WCEL-MaxNumberEDCHCell
- WBTS-MaxNumberEDCHLCG
- WCEL-MaxNumberHSDSCHMACdFlows
- WCEL-MaxNumberHSDPAUsers
- WCEL-MaxNumbHSDPAUsersS
- WCEL-MaxNumbHSDSCHMACdFS
It is recommended to have features Continuous Packet Connectivity (CPCEnabled) and Fractional DPCH (FDPCHEnabled) enabled in the cell so that high
amount of HSPA users is possible. Also feature HSUPA Downlink Physical Channel
Power Control should be in use in BTS so that DL control channel power consumption is in lower level so that more resources is left for user data (more RT users and
more user data).
Note: Simultaneous usage of HSPA 128 users per cell and CPC (enabled with
parameter WCEL-CPCEnabled) requires license to be installed for ‘CPC for 128
HSPA Users’ in RNC and the feature administrative state set as “ON”. Otherwise
HSPA 128 users per cell cannot be enabled.
Id:0900d805809da32a
253
Summary of changes
Related features
1.1.22.38
WCDMA Radio Network Configuration Parameters
HSPA 72 Users Per Cell (optional) AND HSPA 128 users per cell (optional)
HSPASCCSpecificATO (HSPA SCC Specific ATO Value)
Description
This parameter indicates the range of the HSPASCCSpecificATO parameter.
Range is from 0 ms to 300 ms with a step of 10 ms. Default value of the parameter
is 100 ms.
If too high value is applied, timing of synchronized SCC procedure is jeopardised.
If too low value is applied, synchronized SCC procedure is delayed.
The HSPASCCSpecificATO is not applied if either the value of the WCEL
parameter FastActOfTargetServCell is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.22.39
MEHHSUPAUserNbr2msTTI (HSUPA E-DCH 2 ms TTI user number
for the Mass Event)
Description
The parameter determines the number of HSUPA users in the cell to trigger usage
of the E-DCH 10 ms TTI (E-DCH 2 ms TTI prevention) for the Mass Event Handler.
If the value 0 is set to the parameter, the E-DCH 10 ms TTI is used for every
HSUPA UE.
The function is switched on/off by the WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
1.1.22.40
DRXInactiveTimerHSFACH (Inactivity Supervision Timer of HSFACH for DRX User )
Description
This timer is used on MAC -c to detect the idle periods on data transmission (NRT
HSPA RBs and SRBs) for the Rel8 and newer UEs on CELL_FACH using HSFACH with DRX Mode.
Based on this timer the MAC -c shall give No_Data indication to RRC, which
further can change the state of the UE from Cell_FACH state to the Cell_PCH state
(or URA_PCH state).
Related features
High speed Cell_FACH Uplink (optional)
254
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.41
Summary of changes
LayeringRRCRelEnabled (Layering in RRC Connection Release
Enabled)
Description
This parameter defines whether the layering in RRC Connection Release is enabled
in the cell. Layering in RRC Connection Release directs UE to other frequency layer
in RRC Connection Release.
Target frequencies and frequency ranges are defined with parameters under
LayeringRRCConnRelTargFreq structure. If no target frequencies are defined, no
layering is done in RRC Connection Release due to Layering in RRC connection
Release.
Related features
Layering in RRC Connection Release (optional)
1.1.22.42
MEHLoadStateTtT (Load state time-to-trigger for the Mass Event
Handler)
Description
The parameter determines the load state time-to-trigger for the Mass Event
Handler.
The Mass Event Handler uses the load state time-to-trigger for setting the load
state on and off. If the averaged queue length attains or exceeds the threshold
defined by the WCEL-MEHQueueThreshold parameter, the load state functions will
be taken into use after the time-to-trigger defined by the WCEL-MEHLoadStateTtT
parameter expires. If the averaged queue length goes below the threshold defined
by the WCEL-MEHQueueThreshold parameter, the load state functions will cease
after the time-to-trigger defined by the WCEL-MEHLoadStateTtT parameter multiplied by two expires.
The shorter the value of the parameter, the faster the load state functions turn
on and off. Correspondingly, the longer the value of the parameter, the slower the
load state functions turn on and off.
Available load state functions utilising time-to-trigger (controlled by the WCELMassEventHandler parameter):
- Increased TVM pending time
- Temporary maximum bit rate for UL DCH
- Temporary maximum number of HSUPA users
In addition to the Mass Event Handler, also the Automatic Access Class Restriction feature utilises the time-to-trigger for load detection.
Related features
Mass Event Handler (optional) OR Automatic access class restriction (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
255
Summary of changes
1.1.22.43
WCDMA Radio Network Configuration Parameters
MassEventHandler (Mass Event Handler functions)
Description
The parameter determines the Mass Event Handler functions in use.
The functions that are related to the Mass Event Handler are the following:
Bit 0: Increased TVM pending time
Increased TVM pending time is used during high load state.
Bit 1: Temporary maximum bit rate for UL DCH
Temporary maximum bit rate is set to the minimum bit rate for UL DCH during
high load state.
Bit 2: Temporary maximum number of HSUPA users
Temporary maximum number of HSUPA users is used during high load state.
Bit 3: Increased CQI feedback cycle
Increased CQI feedback cycle is used if the number of HSDPA users in the cell
exceeds a pre-defined threshold.
Bit 4: Load based E-DCH 2 ms TTI prevention
E-DCH 10 ms TTI is used instead of E-DCH 2 ms TTI if the number of HSUPA
users in the cell exceeds a pre-defined threshold.
Bit 5: UL load based AC for HSPA+ features
Single Cell HSDPA allocation is done instead of HSPA+, if the load based AC
exceeds the pre-defined threshold or the mass event load state of the cell is active.
Bit value 0: Function is disabled.
Bit value 1: Function is enabled.
Related features
Mass Event Handler (optional)
1.1.22.44
HSDPAMaxCellChangeRepetition (Max number of repetitive serving
HS-DSCH cell changes)
Description
This parameter determines the maximum number of repetitive serving HS-DSCH
cell changes during a predefined time period. If the maximum number of serving
HS-DSCH cell changes is exceeded, HS-DSCH is released. When the value of this
parameter is set to 0, the CTS to DCH due to repetitive SCC's is disabled.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNHSPA
(RNC level) parameter HSDPAMaxCellChangeRepetition determines the
maximum number of repetitive serving HS-DSCH cell changes during a predefined
time period.
The RNHSPA parameter HSDPACellChangeRepetitionTime determines the
time period during which the maximum number of repetitive serving HS-DSCH cell
changes is
counted.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.22.45
Description
256
HSRACHMaxPeriodCollis (Max period for collision resolution phase
for HS-RACH)
This parameter determines the Maximum period for collision resolution phase. The
time has been defined as the terms of TTIs.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Related features
1.1.22.46
Summary of changes
High speed Cell_FACH Uplink (optional)
PrxTargetPSMaxtHSRACH (Max PS target interference level with
HS-RACH)
Description
This parameter defines the the maximum allowed target level for the UL PS NRT
DCH packet scheduling when the HS-RACH has been set up in the cell.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.47
PtxTargetPSMaxtHSRACH (Max PS target power level with HSRACH)
Description
This parameter defines the the maximum allowed target level for the DL PS NRT
DCH packet scheduling when the HS-RACH has been set up in the cell.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.48
HSRACHMaxAllocTimeCCCH (Maximum E-DCH resource alloc time
for CCCH for HS-RACH)
Description
This parameter determines the maximum E-DCH resource allocation for CCCH.
The time has been defined as the terms of TTIs.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.49
HSRACHMaxTotSymbolRate (Maximum total uplink symbol rate of
the HS-RACH)
Description
This parameter determines the planned maximum total uplink symbol rate of the
HS-RACH (maximum total symbol rate of the E-DPDCH(s) in CELL_FACH state) of
the UE in the cell.
Information is signaled to the UE using the RRC SIB5/5bis: Maximum channelisation codes IE and to the BTS using the NBAP PHYSICAL SHARED CHANNEL
RECONFIGURATION REQUEST message: Maximum Set of E-DPDCHs IE within
Common E-DCH System Information.
Related features
High speed Cell_FACH Uplink (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
257
Summary of changes
1.1.22.50
WCDMA Radio Network Configuration Parameters
MBLBLoadInfoDistr (MBLB Load Information Distribution)
Description
This parameter defines whether the HSPA load information (used in Multi-Band
Load Balancing) of the cell is distributed inside the RNC. This same information is
distributed also in case if any of Multi-Band Load Balancing triggers (MBLBRABSetupEnabled, MBLBStateTransEnabled, MBLBInactivityEnabled, MBLBMobilityEnabled) is enabled in the cell. If any of above triggering parameter and this parameter
is not enabled the HSPA load information of this cell is not distributed inside the
RNC meaning that HSPA load information of this cell is not available for Multi-Band
Load Balancing decision making. If the HSPA load information distribution is activated, HS-DSCH and E-DCH provided bit rate measurements are also activated in
the cell. It is better not to set this parameter enabled if the cell cannot be Multi-Band
Load Balancing target cell to avoid unnecessary internal message load and to avoid
unnecessary measurements to be activated.
Note! From the cell where HSDPA is not enabled the HSPA load information
is not distributed and HS-DSCH and E-DCH provided bit rate measurements are not
activated.
Related features
Multi-Band Load Balancing (optional)
1.1.22.51
HSDPACellChangeMinInterval (Minimum interval between serving
HS-DSCH cell changes)
Description
This parameter determines the minimum interval between serving HS-DSCH cell
changes when the periodical CPICH Ec/No reporting indicates that the maximum
allowed difference between the CPICH Ec/No of the best active set cell and the
CPICH Ec/No of the serving HS-DSCH cell is exceeded. Timer is started after every
successfully executed serving HS-DSCH cell change. During the time period,
serving HS-DSCH cell changes triggered by the periodical CPICH Ec/No reporting
are forbidden. If the value of this parameter is set to 0, serving HS-DSCH cell
changes are not restricted.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNMOBI
(RNC level) parameter HSDPACellChangeMinInterval determines the minimum
interval between serving HS-DSCH cell changes.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
258
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.52
Summary of changes
HSRACHCommonEDCHRes (Number of Common E-DCH
Resources for HS-RACH)
Description
This parameter defines the number of Common E-DCH Resources of the HS-RACH
configuration in the cell. Common E-DCH resource(s) is(are) setup in the cell when
the HS-RACH is setup in the cell. Common E-DCH resources configured during HSRACH setup are under direct control of the Node B and are shared by UEs in
CELL_FACH and IDLE mode. The RNC is not involved in the assignment of these
resources to UEs. Since only one cell is involved in the resource allocation, soft
handover is not possible.
Note that the number of configured Common E-DCH resources is practically
same as maximum number of HS-RACH user can send data within same TTI on
HS-RACH in the cell.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.53
ActivationTimeOffset (Offset for activation time)
Description
This parameter determines the offset value that is added to the activation time,
which RNC has produced internally for a synchronised radio link handling procedure. Connection Frame Number (CFN) which is set to the "activation time" fields of
the NBAP and RRC messages indicate the activation time of the reconfiguration.
Value of the CFN is produced by adding (modulo 256) the sum of the RRC message
length and the calculated SRB bit rate dependent offset value, and the value of this
parameter to the current CFN provided by the Frame Protocol (FP). Activation time
offset represents the AM RLC retransmissions of the SRB and the processing delay
of RNC and BTS. This parameter is applicable when the DL SL is mapped on DCH.
Too low activation time offset value increases the possibility of UE and radio
interface failures. Too high activation time offset value delays the mobility control of
the fast moving UEs.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNPS (RNC
level) parameter ActivationTimeOffset determines the offset for the activation time.
Related features
Fast HSPA Mobility (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
259
Summary of changes
1.1.22.54
WCDMA Radio Network Configuration Parameters
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA)
Description
This parameter determines the offset value that is added to the activation time,
which RNC has produced internally for a synchronised radio link handling procedure. Connection Frame Number (CFN) which is set to the "activation time" fields of
the NBAP and RRC messages indicate the activation time of the reconfiguration.
Value of the CFN is produced by adding (modulo 256) the value of this parameter
to the current CFN provided by the Frame Protocol (FP). This parameter is applicable when the SRBs are mapped on E-DCH/HS-DSCH.
Too low activation time offset value increases the possibility of UE and radio
interface failures. Too high activation time offset value delays the mobility control of
the fast moving UEs.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNHSPA
(RNC level) parameter ATOSRBsOnHSPA determines the offset for the activation
time.
Related features
Fractional DPCH (optional) AND Fast HSPA Mobility (optional)
1.1.22.55
OffsetToBeginCTCHBSIndex (Offset to Begin CTCH Block Set
Index)
Description
Controls the frequency of idle schedule messages for Service Area Broadcast.
Smaller values mean more frequent scheduling and faster response, but increase
UE battery consumption. Values below 16 restrict maximum message size gradually. The parameter is a pointer to the first CTCH Block Set (BS) of the next CBS
Schedule Period relative to the CTCH BS index of the first part of the current BMC
Schedule Message.
With the default value 255 scheduling time period is the longest having long
intervals in sending the block sets thus consuming the least UE battery capacity.
OffsetToBeginCTCHBSIndex parameter is applicable when WCEL-SABEnabled is set as Enabled.
Related features
( Service Area Broadcast (optional) OR SAB Support with 2 SCCPCHs (optional)
) AND Terminal Battery Drain Prevention in Cell Broadcast (optional)
1.1.22.56
PowerOffsetPreamHSRACH (Power Offset Last Transmitted
Preamble for HS-RACH)
Description
This parameter defines the power offset between the last transmitted preamble and
the initial power of the DPCCH transmission ("Power offset P p-e") in HS-RACH (the
Enhanced Uplink in CELL_FACH state and Idle mode).
Related features
High speed Cell_FACH Uplink (optional)
260
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.57
Summary of changes
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation)
Description
This parameter indicates whether the Power Offset Update Message Size Optimisation functionality is enabled in the cell.
When enabled in the cell, this functionality introduces message size optimisation for RRC: PHYSICAL CHANNEL RECONFIGURATION message, which is used
to update HS-DPCCH power offsets. Unnecessary IEs (namely Downlink information common for all radio links IE and Downlink information per radio link list IE) are
omitted resulting that message size is reduced. In some cases it will reduce from 2
to 1 TB (Transport Block). Message size reduction leads to faster and more reliable
signaling.
The Power Offset Update message size is not optimised if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
Fast HSPA Mobility (optional)
1.1.22.58
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No)
Description
This parameter determines the reporting period of the CPICH Ec/No measurement,
which is used as a criterion for the serving HS-DSCH cell change procedure.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNMOBI
(RNC level) parameter HSDPACPICHReportPeriod determines the reporting
period of the CPICH Ec/No measurement.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
1.1.22.59
MEHQueueThreshold (Scheduling queue threshold for the Mass
Event Handler)
Description
The parameter determines the scheduling queue threshold for the Mass Event
Handler.
The Mass Event Handler uses the scheduling queue threshold for detection of
the load state. If the averaged queue length attains or exceeds the threshold defined
by this parameter, the load state functions will be taken into use after time-to-trigger
defined by the WCEL-MEHLoadStateTtT parameter expires.
The lower the value of the parameter, the lower load is needed to trigger the
load state functions on. Correspondingly, the higher the value of the parameter, the
higher load is needed to trigger load state functions on.
The available load state functions utilising the scheduling queue length (controlled by the WCEL-MassEventHandler parameter):
- Increased TVM pending time
- Temporary maximum bit rate for UL DCH
- Temporary maximum number of HSUPA users
In addition to the Mass Event Handler, also the Automatic Access Class Restriction feature utilises the scheduling queue length for load detection.
Related features
Mass Event Handler (optional) OR Automatic access class restriction (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
261
Summary of changes
1.1.22.60
WCDMA Radio Network Configuration Parameters
SABEnabled (Service Area Broadcast Enabled)
Description
This parameter enables Service Area Broadcast in a WCDMA cell. If the parameter
value is set as Enabled, Service Area Broadcast is activated. When it is set to Disabled, there will not be any Service Area Broadcast handling in the WCEL.
For activation of RAN2527 SAB Support with 2SCCPCHs, License for legacy
SAB and RAN 2527 are required.
Related features
Service Area Broadcast (optional) OR SAB Support with 2 SCCPCHs (optional)
1.1.22.61
SmartLTELayeringEnabled (Smart LTE Layering Enabled)
Description
The parameter indicates whether or not the Smart LTE Layering feature is enabled
in the cell. It also defines what triggering points are used. The following two triggering points are available:
- RRC state change of the UE away from CELL_DCH state
- channel type switch from HSPA or from HSDPA to DCH.
- CS RAB release.
Channel type switch means here cases where HS-DSCH is tried to be switched
to DCH (E-DCH/HS-DSCH --> DCH/DCH or DCH/HS-DSCH --> DCH/DCH) with
some other bit rate than 0 (pure release cases are excluded).
CS RAB release trigger means case where an UE has CS RAB and at least
one active PS RAB and then CR RAB is released (UE would stay in CELL_DCH
state in WCDMA).
Cell specific CPICH RSCP threshold for the functionality is set with the SmartLTELayeringRSCP parameter.
Cell specific user amount threshold for the functionality is set with the SmartLTELayeringUA parameter.
Services that the UE to be redirected to LTE can be using are set with the SmartLTELayeringServ parameter.
The minimum time that the UE must be in WCDMA system after RRC Connection Setup Complete has been received or when Relocation Request for PS service
is received is set with the parameter SmartLTELayeringPrevT.
Redirection allowance to FDD LTE, TDD LTE or both of them is set with the
SmartLTELayeringTSysSel parameter.
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
262
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.62
Summary of changes
SmartLTELayeringUA (Smart LTE Layering NRT user amount
threshold)
Description
The parameter defines a user amount threshold that must be exceeded before
Smart LTE Layering can be done. User amount is checked in cell level and just NRT
users (Interactive and Background) are counted.
An user is counted in those cells where the user in question has DCH, HSDSCH or E-DCH.
If the NRT user amount check allows the Smart LTE layering, then it is not
prevented again right after NRT user amount is smaller than the parameter value,
but there is a fixed hysteresis of 5 users. When the user amount is more than 5
users below of the parameter value, then the Smart LTE layering is not allowed
anymore.
Checking of user amount can be deactivated by setting the value 0.
Real default value for this threshold cannot be defined, because it depends on
radio network planning.
If too small value is used, then too many UEs might be redirected to LTE and
there are free capacity in WCDMA side. If too big value is used, then too many UEs
stays in WCDMA side and so causes load there when there could be free capacity
in LTE side.
Smart LTE Layering is enabled with the SmartLTELayeringEnabled parameter.
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
1.1.22.63
SmartLTELayeringRSCP (Smart LTE Layering RSCP threshold)
Description
The parameter defines CPICH RSCP threshold that must be exceeded before
Smart LTE Layering can be done. The parameter can be used for example cases
where WCDMA and LTE cells are co-located and LTE cell has smaller coverage.
Checking of CPICH RSCP can be deactivated by setting the value 0.
Real default value for this threshold cannot be defined, because it depends on
radio network planning.
If too small value is used, then redirection can be done to too weak LTE cell
causing that UE comes back to WCDMA. If too big value is used, then redirection is
not done when it should be done.
Smart LTE Layering is enabled with the SmartLTELayeringEnabled parameter.
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
1.1.22.64
Description
DN00211177
Issue 12B
SmartLTELayeringTSysSel (Smart LTE Layering Target System
Selection)
The parameter indicates if the redirection is allowed to FDD LTE, TDD LTE or to
both of them. If redirection is prevented to FDD or to TDD, then neighbor frequencies in question are not given to UE at all.
The parameter is used only in those cells where the Smart LTE Layering feature
is activated (SmartLTELayeringEnabled).
Id:0900d805809da32a
263
Summary of changes
Related features
1.1.22.65
WCDMA Radio Network Configuration Parameters
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
LayeringRRCConnRelTargFreq/TargetFrequency (Target frequency)
Description
This parameter defines the target frequency for layering in RRC connection release.
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency.
Default value 0 means that UE is not directed to other frequency in RRC
Connection Release due to Layering in RRC connection Release.
Parent parameter
LayeringRRCConnRelTargFreq
Related features
Layering in RRC Connection Release (optional)
1.1.22.66
LayeringRRCConnRelTargFreq (Target frequency for layering in
RRC Connection Release)
Description
This parameter structure defines the possible target frequencies for layering in RRC
connection release. Up to 8 different FDD UMTS frequencies can be defined. If
there are several target frequencies defined RNC fills the frequencies in round robin
order (in ICSU level) to consecutive RRC Connection Release messages at the cell.
Child parameters
•
Related features
Layering in RRC Connection Release (optional)
1.1.22.67
TargetFrequency
VCPMaxHSDPAUsers (Temporary max number of HSDPA users for
the VCP)
Description
The parameter determines the temporary maximum number of HSDPA users
allowed during the HSDPA prevention for the Voice Call Prioritisation during High
Traffic Load.
The lower the value of the parameter, the fewer users are allowed during the
HSDPA prevention.
The function is switched on/off by the WCEL-VoiceCallPriority parameter.
Related features
Voice Call Priorization during High Traffic Load (optional)
264
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.68
Summary of changes
MEHMaxHSUPAUsers (Temporary max number of HSUPA users for
the Mass Event)
Description
The parameter determines the temporary maximum number of HSUPA users for
the Mass Event Handler.
The Mass Event Handler uses the temporary maximum number of HSUPA
users to limit E-DCH allocations during high load. Detection of the high load is based
on the average scheduling queue length. Threshold for the average scheduling
queue length is defined by the WCEL-MEHQueueThreshold parameter.
If the value 0 is set to the parameter, HSUPA allocations are prevented in the
cell during the high load state.
Usage of the temporary maximum number of HSUPA users is controlled by the
WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
1.1.22.69
HSRACHActivityThr (Threshold of the E-DCH MAC-d flow of PS RB
on HS-RACH)
Description
This parameter defines the activity threshold for the activity measurement of the EDCH MAC-d flow of PS RB on CELL_FACH state using HS-RACH. The threshold
is defined as a number of bits per second. The activity measurement measures the
number of bits transmitted by the E-DCH MAC-d flow during the sliding measurement window. The sliding measurement window is defined with the HSRACHActivityAveWin parameter. If the result of the activity measurement is more than or equal
to the threshold, the HSRACHActTimeTrigger is started.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.70
HSRACHActTimeToTrigger (Time to trigger for activity measurement on HS-RACH)
Description
This parameter defines the activity time to the trigger timer for the activity measurement of the E-DCH MAC-d flow of PS RB on CELL_RACH state using HS-RACH.
If the result of the activity measurement is higher than or equal to the HSRACHActivityThr, the HSRACHActTimeToTrigger is started. If the result of the activity measurement is lower than the HSRACHActivityThr, the HSRACHActTimeToTrigger is
stopped and reset. If the timer expires, it triggers a uplink capacity request with state
change request from CELL_RACH to CELL_DCH.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.71
Description
DN00211177
Issue 12B
HSRACHTimeToTrigger (Traffic volume measurement time to
trigger of HS-RACH)
This parameter defines, in ms, the period between the timing of event detection and
timing of sending a traffic volume measurement report for the UEs on CELL_FACH
state using HS-RACH in UL. This parameter is sent to the UE using an RRC: MEASUREMENT CONTROL message.
Id:0900d805809da32a
265
Summary of changes
Related features
1.1.22.72
WCDMA Radio Network Configuration Parameters
High speed Cell_FACH Uplink (optional)
UEDRXCapability (UE DRX in Cell_FACH capability)
Description
RAN1908: UE DRX in Cell_FACH feature enables discontinuous reception (UE
DRX) for High Speed Cell_FACH for Rel8 or newer UE releases. This parameter
defines the Cell specific UE DRX capability as received from the BTS.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.73
HSFACHDRXEnabled (UE DRX with High Speed Cell FACH Enabled)
Description
This parameter Enables/Disables the use of DRX in High Speed CELL_FACH in the
cell.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.74
UePeriodicMeasEnabled (UE Periodic Measurement Report
Enabled)
Description
The operator can enable or disable the UE Periodic Measurement Report feature
with this parameter in this cell.
Related features
UE Periodic Measurement Report (optional)
266
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.75
Summary of changes
MEHULLHSDPAUALimit (UL load based HSDPA user amount limit
for the MEH)
Description
The parameter sets limit for the UL load based HSDPA user amount in the cell. If
the calculated UL load based HSDPA user amount exceeds this limit, then SCHSDPA is used in the cell for new HS-DSCH allocations. The purpose of the check
is to control the UL load that is caused by HSDPA users. This parameter has no
impact on UL transport channel type selection.
The calculation of UL load based HSDPA user amount takes the following things
into account:
- HSDPA user type (SC/DC/MIMO)
- amount of CPC users of the cell
- amount of non-CPC users of the cell with normal CQI feedback cycle
- amount of non-CPC users with extended CQI feedback cycle (MEH)
- amount of DCH users of the cell
The UL load based HSDPA user amount check is deactivated totally by using
value 0.
Small values of the parameter prevents use of DC/MIMO easily, which leads
to low DL peak rates.
Big values of the parameter do not protect UL from extra L1 control channel
load caused by DC/MC/MIMO users, which leads to a low user data throughput.
Also the mass event load state of the cell prevents the allocation of
DC/MC/MIMO, regardless of the value of MEHULLHSDPAUALimit.
With the default value 30, it is possible to allocate:
- 18 MIMO/DC calls
- 11 MIMO/DC calls and 11 SC HSDPA calls
- 1 MIMO/DC call and 28 SC HSDPA calls
This with no UL DCH allocations in the cell and with normal CQI allocations (no
CPC users and no MEH CQI usage)
Notice that WCEL – MassEventHandler must be also configured to activate the
functionality.
Related features
Mass Event Handler (optional)
1.1.22.76
HSRACHVolThrUL (UL traffic volume measurement threshold of HSRACH)
Description
This parameter defines, in bytes, the threshold of data in the RLC buffers of SRB0,
SRB1, SRB2, SRB3, SRB4 and all NRT RBs that triggers the uplink traffic volume
measurement report, when the UE is in Cell_FACH state and using HS-RACH. Otherwise, UE sends data on HS-RACH. This parameter is sent to the UE using an
RRC: MEASUREMENT CONTROL message.
Related features
High speed Cell_FACH Uplink (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
267
Summary of changes
1.1.22.77
WCDMA Radio Network Configuration Parameters
SmartTrafVolThrUL (UL traffic volume threshold for Smartphone)
Description
The parameter defines, in bytes, the threshold of data in the RLC buffers of SRB3,
SRB4 and all NRT RBs that trigger the uplink traffic volume measurement report
(capacity request) on MAC, when UE is in Cell_FACH state. Otherwise, RNC sends
data on FACH. The parameter is used for the identified Smartphone instead of the
TrafVolThresholdULLow parameter.
Related features
Fast Dormancy Profiling (optional)
1.1.22.78
HSRACHExtendedAI (Use of Extended Acquisition Indicator HSRACH)
Description
This parameter determines the use of Extended Acquisition Indicators (E-AI). TRUE
indicates that E-AI is used when HS-RACH is configured. FALSE indicates that EAI is not used when the HS-RACH is configured.
The original AICH signature space can be extended from 16 signatures (as
defined in Rel99) to totally 32 signatures by the using of the E-AI. Extended Acquisition Indicators (E-AI) represents a set of values corresponding to a set of E-DCH
resource configurations.
When the E-AI is used, indication is signaled to BTS by NBAP:PHYSICAL
SHARAED CHANNEL RECONFIGURATION message to UEs via RRC:SIB5/5bis.
Related features
High speed Cell_FACH Uplink (optional)
1.1.22.79
VoiceCallPriority (Voice Call Prioritisation During High Traffic Load)
Description
The parameter enables/disables the Voice Call Prioritisation During High Traffic
Load feature in the cell.
Related features
Voice Call Priorization during High Traffic Load (optional)
268
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.22.80
Summary of changes
VCPPtxOffset (Voice Call Priority target threshold for HSDPA prevention)
Description
The parameter determines the level of the estimated non-controllable DL power to
start HSDPA prevention in the cell. The level is expressed in dB below WCEL-PtxTarget.
If the estimated non-controllable power is equal or higher than the level determined (PtxTarget – VCPPtxOffset), HSDPA prevention, that is the temporary
maximum number of HSDPA users (TMHD) determined by the WCEL-VCPMaxHSDPAUsers parameter, is taken into use.
The parameter provides possibility to use HSDPA prevention (TMHD) in a
reactive or proactive mode.
The reactive mode (default 0 dB) means that TMHD is taken into use when the
estimated non-controllable DL power meets PtxTarget. This is recommended value
if PtxOffset > 0 dB because AMR CS DCH user can be admitted up to (PtxTarget +
PtxOffset).
The proactive mode (value > 0 dB) means that TMHD is taken into use before
the estimated non-controllable DL power meets PtxTarget. This is recommended if
PtxOffset = 0 or very close to PtxTarget because HSDPA traffic is started to be
limited before possible AMR CS DCH congestion.
The function is switched on/off by the WCEL-VoiceCallPriority parameter.
Related features
Voice Call Priorization during High Traffic Load (optional)
1.1.22.81
Description
1.1.22.82
WACSetIdentifier (WAC Parameter Set Identifier)
Pointer to the WAC object identifier. Defines the WAC parameter set to be used in
this cell.
HSRACHActivityAveWin (Window size of E-DCH MAC-d flow of PS
RB on HS-RACH)
Description
This parameter defines the size of the sliding averaging window for the activity measurement of the E-DCH MAC-d flow of PS RB when the UE is on CELL_FACH state
using HS-RACH. The activity measurement measures the number of bits transmitted by the E-DCH mac-d flow during the sliding measurement window. The value 0
of the parameter means that the E-DCH MAC-d flow activity measurement is not
performed.
Related features
High speed Cell_FACH Uplink (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
269
Summary of changes
1.1.23
1.1.23.1
WCDMA Radio Network Configuration Parameters
WRAB
L1BLERTEDCHPSConvSpe10 (BLER target for PS Conversational
speech E-TTI 10 ms)
Description
This parameter defines the L1 BLER target for the E-DCH MAC-d flow of the PS
conversational speech RB (Source Statistics Descriptor PS core network has set as
a "speech" or in case of push to talk service) when the E-TTI equals to 10 ms. It is
used by the outer loop power control of the RNC. E-HARQ retransmission threshold
for the block error detection is defined with the management parameter "HARQ
threshold for OLPC of PS Conv Speech E-TTI 10 ms".
Use of too high value wastes radio resources and too low value causes voice
quality problems.
Value of the parameter equals to the log10 of the BLER value.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
1.1.23.2
L1BLERTEDCHPSConvSpe2 (BLER target for PS Conversational
speech E-TTI 2 ms)
Description
This parameter defines the L1 BLER target for the E-DCH MAC-d flow of the PS
conversational speech RB (Source Statistics Descriptor PS core network has set as
a "speech" or in case of push to talk service) when the E-TTI equals to 2 ms. It is
used by the outer loop power control of the RNC. E-HARQ retransmission threshold
for the block error detection is defined with the management parameter "HARQ
threshold for OLPC of PS Conv Speech E-TTI 2 ms".
Use of too high value wastes radio resources and too low value causes voice
quality problems.
Value of the parameter equals to the log10 of the BLER value.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
270
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.23.3
Summary of changes
EbNoDCHRateGain/EbNoDCHRateGainPSConvSpe (Data rate gain
for the Eb/N0 of the PS conv speech)
Description
This parameter defines the value of the data rate gain for the planned Eb/N0s of the
DCHs which transfer the radio bearers of the PS conversational speech RABs. Data
services are generally encoded with Turbo, which becomes more efficient with the
higher data rates, in the same way as interleaving does. Higher transmission power
is used for the DPCCH with the higher data rates; it improves the channel estimation
and consequently the Eb/N0 performance. Therefore the rate matching Eb/N0s can
be reduced also for the low data rate bearers when they are transferred in the multiservice configuration of an aggregate data rate which is high enough. The selector
parameters "Data rate gain selector for the Eb/N0 of the UL DCH" and "Data rate
gain selector for the Eb/N0 of the DL DCH" define the physical channel data rates
(spreading factors) for which the data rate gain is valid. If the value of the selector
parameter shows that with the maximum DPDCH data rate the gain is applicable,
then the value of the actual gain parameter is added to the value of the rate
matching Eb/N0 value of the data service.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
The parameter is significant with the push to talk services. To modify this
parameter, you must manually lock and later unlock all WCEL objects related to this
WRAB. This will severely impact the network. You can avoid it by creating a new
WRAB and gradually transferring the WCELs to this one.
Parent parameter
EbNoDCHRateGain
Related features
Optimised push to talk experience (optional)
1.1.23.4
EbNoEDCHPSConvSpeech (Eb/N0 planned for E-DCH PS conversational speech)
Description
Parameter defines the planned Eb/N0 for E-DCHs which are transferring radio
bearers of the PS conversational speech RABs (value of Source Statistics Descriptor is "speech" or in case of push to talk service). Parameter is applied in the definition of the load factor which is used in admission control and packet scheduling
algorithms of the radio resource management.
Use of too high value wastes radio resources and too low value causes quality
problems.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
271
Summary of changes
1.1.23.5
WCDMA Radio Network Configuration Parameters
EDCHBLERAdjPSConvSpe10 (HARQ threshold for OLPC of PS
Conv Speech E-TTI 10 ms)
Description
Management parameter defines the L1 HARQ retransmissions threshold for the
outerloop power control dedicated to the E-DCH MAC-d flow of the PS conversational speech RB (Source Statistics Descriptor PS core network has set as a
"speech" or in case of push to talk service) when the E-TTI equals to 10 ms. Its value
is used by the outer loop power control of the RNC for the detection of the block
error. Block error is occurred if the number of the retransmissions equals to the
value of the parameter or a HARQ failure has observed. Outerloop power control
adjusts the uplink DPCCH SIR target after the occurred block errors. This threshold
value is used when the BLER target has been defined with the management parameter “BLER target for PS Conversational speech E-TTI 10 ms”.
Use of too high or low value causes voice quality problems (delay or data loss).
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
1.1.23.6
EDCHBLERAdjPSConvSpe2 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 2 ms)
Description
Management parameter defines the L1 HARQ retransmissions threshold for the
outerloop power control dedicated to the E-DCH MAC-d flow of the PS conversational speech RB (Source Statistics Descriptor PS core network has set as a
"speech" or in case of push to talk service) when the E-TTI equals to 2 ms. Its value
is used by the outer loop power control of the RNC for the detection of the block
error. Block error is occurred if the number of the retransmissions equals to the
value of the parameter or a HARQ failure has observed. Outerloop power control
adjusts the uplink DPCCH SIR target after the occurred block errors. This threshold
value is used when the BLER target has been defined with the management parameter “BLER target for PS Conversational speech E-TTI 2 ms”.
Use of too high or low value causes voice quality problems (delay or data loss).
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
272
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.23.7
Summary of changes
SIRDPCCHInitialEDCH (Initial SIR target for UL DPCCH with E-DCH)
Description
The parameter defines the initial SIR target for the UL DPCCH when the radio link
has E-DCH configured in the uplink transfer direction. The parameter is used only
in case of push to talk service.
The value of the parameter is used in the configuration of the SIR target for the
uplink outer loop power controller of the RNC.
The values of E-TTI for PTT initial SIR targets are defined assuming 1-way
receiver diversity. The Initial SIR target values for the 2- and 4-way receiver diversity
cases are achieved by adding particular offset values to the 1-way receiver diversity
values of the initial SIR targets. The offset values are defined with two management
parameters (SIRDPCCHInitialDCHRxDiv2 and SIRDPCCHInitialDCHRxDiv4).
The initial SIR target value is sent to the BTS and to the outer loop power controller of the RNC.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Child parameters
•
•
Related features
Optimised push to talk experience (optional)
1.1.23.8
SIRDPCCHInitialEDCHPTT10MS
SIRDPCCHInitialEDCHPTT2MS
SIRDPCCHInitialEDCH/SIRDPCCHInitialEDCHPTT10MS (Initial SIR
target for UL DPCCH with E-TTI 10 ms - PTT)
Description
This parameter defines the initial SIR target of UL DPCCH when the radio link has
E-DCH configured with E-TTI=10ms for RB of PTT. One-way receiver diversity is
assumed.
Use of too high value wastes radio resources and too low value causes quality
problems.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
Parent parameter
SIRDPCCHInitialEDCH
Related features
Optimised push to talk experience (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
273
Summary of changes
1.1.23.9
WCDMA Radio Network Configuration Parameters
SIRDPCCHInitialEDCH/SIRDPCCHInitialEDCHPTT2MS (Initial SIR
target for UL DPCCH with E-TTI 2 ms - PTT)
Description
This parameter defines the initial SIR target of UL DPCCH when the radio link has
E-DCH configured with E-TTI=2ms for RB of PTT. One-way receiver diversity is
assumed.
Use of too high value wastes radio resources and too low value causes quality
problems.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
Parent parameter
SIRDPCCHInitialEDCH
Related features
Optimised push to talk experience (optional)
1.1.23.10
EbNoOfPSConvSpe/EbNoDCHOfPSConvSpe (Planned Eb/N0 of the
PS conversational speech)
Description
This parameter defines the planned Eb/N0 for the PS conversational speech
service.
The management parameter EbNoDCHOfPSConvSpeQua defines the
appropriate value of the quality target. This parameter is applicable for all DCH user
data rates when the 1-way receiver diversity is assumed. The value of the parameter represents the low data rate value without the possible data rate gain. The data
rate gain value is defined separately with the management parameter EbNoDCHRateGainPSConvSpe. The decision whether the data rate gain is applied with a
particular physical channel data rate is done with the management parameters
EbNoDCHRateGainSFUp for uplink and EbNoDCHRateGainSFDown for downlink.
The final planned Eb/N0 value is obtained by adding the data rate gain to the Eb/N0
value of the parameter. The resulting Eb/N0 value is applied in producing the
service specific rate matching attributes.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
Parent parameter
EbNoOfPSConvSpe
Related features
Optimised push to talk experience (optional)
274
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.1.23.11
Summary of changes
EbNoOfPSConvSpe/EbNoDCHOfPSConvSpeQua (Quality target of
the PS conversational speech)
Description
The parameter defines the quality target for the PS conversational speech service.
The same quality target is used for both uplink and the downlink transfer directions.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
Parent parameter
EbNoOfPSConvSpe
Related features
Optimised push to talk experience (optional)
1.1.23.12
EbNoOfPSConvSpe (Rate matching with the PS conversational
speech services)
Description
The parameters of this structure define the quality targets of the PS conversational
speech service and the planned Eb/N0s of their DCHs.
An additional management parameter is introduced to assign a data rate gain
value for higher data rate services; the final Eb/N0 values are achieved by adding
the data rate gain to the quality target specific Eb/N0 values. The planned Eb/N0s
are applied in producing the service specific rate matching attributes.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
Child parameters
•
•
Related features
Optimised push to talk experience (optional)
1.1.23.13
EbNoDCHOfPSConvSpe
EbNoDCHOfPSConvSpeQua
SIRDPCCHInitialDCH/SIRDPCCHInitialDCHPSConvSpe (UL SIR
target regardless of DL channel - PS conv speech)
Description
This parameter defines the initial SIR target for the UL DPCCH when the radio link
has only DCHs configured in the uplink transfer direction for PS conversational
speech RB regardless of used DL channel. One-way receiver diversity is assumed.
Too low value causes too low success rate for first data packets. Too high
value causes UL power spiking
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
Parent parameter
SIRDPCCHInitialDCH
Related features
Optimised push to talk experience (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
275
Summary of changes
WCDMA Radio Network Configuration Parameters
1.2
Changed parameters in RNC RN7.0
1.2.1
ADJD
1.2.1.1
Field
AdjdRTWithHSDPAHopsId (HSDPA HOPS identifier for speech services)
RNC RN6.0 2.0
RNC RN7.0
Full Name
HSDPA HOPS identifier for AMR multiservice
HSDPA HOPS identifier for speech
services
Description
The parameter identifies the parameter
set (HOPS object) which controls the
intra-frequency handover to the additional neighbour cell when a user has HSDSCH allocated simultaneously with the
AMR speech CS RAB.
The parameter identifies the parameter
set (HOPS object) which controls the
intra-frequency handover to the additional neighbour cell when a user has HSDSCH allocated simultaneously with the
AMR speech CS RAB or when the user
has push to talk allocated on HS-DSCH.
Related parameters
HOPSId of HOPS - Check that the
relevant HOPS object exists in the database.
HOPSId of HOPS - Check that the
relevant HOPS object exists in the database.
HSDPAenabled of WCEL - If AMR
service can be used with HS-DSCH and
HSDPA is enabled in the parent cell of
the additional intra-frequency neighbour
cell, the special value 'Not defined' is not
allowed for AdjdRTWithHSDPAHopsId.
HSDPAenabled of WCEL - If AMR
service can be used with HS-DSCH and
HSDPA is enabled in the parent cell of
the additional intra-frequency neighbour
cell, the special value 'Not defined' is not
allowed for AdjdRTWithHSDPAHopsId.
AMRWithHSDSCH of RNFC - If AMR
service can be used with HS-DSCH and
HSDPA is enabled in the parent cell of
the additional intra-frequency neighbour
cell, the special value 'Not defined' is not
allowed for AdjdRTWithHSDPAHopsId.
AMRWithHSDSCH of RNFC - If AMR
service can be used with HS-DSCH and
HSDPA is enabled in the parent cell of
the additional intra-frequency neighbour
cell, the special value 'Not defined' is not
allowed for AdjdRTWithHSDPAHopsId.
PTTEnabled of RNFC - If use of HSDPA
is enabled for PTT with the parameter
PTTEnabled (value > 1) and HSDPA is
enabled in the parent cell of the additional
intra-frequency neighbour cell, the
special value 'Not defined' is not allowed
for AdjdRTWithHSDPAHopsId.
Related features
276
Soft Handover Based on Detected Set
Reporting (optional) AND HSDPA
(optional)
Id:0900d805809da32a
Soft Handover Based on Detected Set
Reporting (optional) AND HSDPA
(optional)
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.2
1.2.2.1
Field
Description
DN00211177
Issue 12B
Summary of changes
ADJG
AdjgSIB (Include in System Information)
RNC RN6.0 2.0
RNC RN7.0
The parameter indicates whether the
GSM neighbour cell is included in the
System Information Block
11&11bis&12&18 for the cell selection
and re-selection procedures. The GSM
neighbour cell is included in the system
information when the value of the parameter is "SIB". The GSM neighbour cell is
included in the extended system information when the value of the parameter is
"SIBbis". The value of the parameter is
set by the system for the GAN neighbour
cell.
If the Wireless Priority Service feature
is enabled, then the parameter Include in
System Information shall be set to have
value "SIB" for ADJG-0.
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47. When HCS is used, the
capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which are included in the System
Information, exceeds the physical size of
SIB data, the NBAP interface is not able
to pack the neighbour cell information
into the SIB data and the scheduling of
the system information blocks fails. The
cell is blocked by the system and an
alarm 7771 WCDMA CELL OUT OF USE
(BCCH scheduling error) is reported for
the cell.
The parameter indicates whether the
GSM neighbour cell is included in the
System Information Block
11&11bis&12&18 for the cell selection
and re-selection procedures. The parameter also indicates whether the GSM
neighbour cell is monitored for the intersystem handover in CELL_DCH state of
connected mode. The GSM neighbour
cell is included in the system information
when the value of the parameter is "For
SIB and CELL DCH meas" or "For SIB
only". The GSM neighbour cell is
included in the extended system information when the value of the parameter is
"For SIBbis and CELL DCH meas" or
"For SIBbis only". The value of the
parameter is set by the system for the
GAN neighbour cell.
The GSM neighbour cell is monitored
for the inter-system handover regardless
of the value of the parameter AdjgSIB if
the value of the RNFC parameter FemtoHandoverControl is "Disabled". If the
value of the RNFC parameter FemtoHandoverControl is "Enabled":
- the GSM neighbour cell is monitored
for the inter-system handover if the value
of the parameter AdjgSIB is set to "For
CELL DCH meas only", "For SIB and
CELL DCH meas" or "For SIBbis and
CELL DCH meas".
- the GSM neighbour cell is not monitored for the inter-system handover if the
value of the parameter AdjgSIB is set to
"For SIB only" or "For SIBbis only".
If the Wireless Priority Service feature
is enabled, then the parameter Include in
System Information shall be set to have
value "For SIB and CELL DCH meas" for
ADJG-0.
Id:0900d805809da32a
277
Summary of changes
Field
WCDMA Radio Network Configuration Parameters
RNC RN6.0 2.0
RNC RN7.0
Note: The parameter AdjgSIB does not
affect GSM measurements in
CELL_DCH state of the connected mode.
That is, all GSM neighbour cells are monitored for the inter-system handover
regardless of the value of the parameter
AdjgSIB.
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47 when all cell re-selection
parameters are broadcasted. When HCS
is used, the capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which are included in the System
Information, exceeds the physical size of
SIB data, the NBAP interface is not able
to pack the neighbour cell information
into the SIB data and the scheduling of
the system information blocks fails. The
cell is blocked by the system and an
alarm 7771 WCDMA CELL OUT OF USE
(BCCH scheduling error) is reported for
the cell.
Range and step
0 (No), 1 (SIB), 2 (SIBbis)
0 (For CELL DCH meas only), 1 (For SIB
and CELL DCH meas), 2 (For SIBbis and
CELL DCH meas), 3 (For SIB only), 4
(For SIBbis only)
Default value notes
The GSM neighbour cell is included in the
system information.
The GSM neighbour cell is included in the
system information and monitored for the
inter-system handover.
278
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Related parameters
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
AdjiSIB of ADJI - Parameter indicates
whether the inter-frequency neighbour
cell is included in the System Information
for the cell selection and re-selection procedures.
AdjiSIB of ADJI - Parameter indicates
whether the inter-frequency neighbour
cell is included in the System Information
for the cell selection and re-selection procedures.
AdjsSIB of ADJS - Parameter indicates
whether the intra-frequency neighbour
cell is included in the system information
for the cell selection and re-selection procedures.
AdjsSIB of ADJS - Parameter indicates
whether the intra-frequency neighbour
cell is included in the system information
for the cell selection and re-selection procedures.
ADJGType of ADJG - Parameter value is
always "No" if the value of ADJGType is
"GAN cell".
ADJGType of ADJG - Parameter value is
always "No" if the value of ADJGType is
"GAN cell".
WireLessPriorityService of RNFC - If
Wireless Priority Service feature is
enabled, then AdjgSIB must be set with
the default value in ADJG-0 instance.
1.2.2.2
ADJGId (Inter-system adjacency identifier)
Field
RNC RN6.0 2.0
Range and step
1.2.3
1.2.3.1
Field
Range and step
1.2.3.2
Field
Description
DN00211177
Issue 12B
0..31, step 1
RNC RN7.0
0..95, step 1
ADJI
BlindHOTargetCell (Blind HO target cell)
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
RNC RN7.0
0 (Disabled), 1 (Enabled)
AdjiCI (Cell Identifier)
RNC RN6.0 2.0
RNC RN7.0
An inter-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJI objects is required.
An inter-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier.
Id:0900d805809da32a
279
Summary of changes
1.2.3.3
Field
Description
280
WCDMA Radio Network Configuration Parameters
AdjiSIB (Include in System Information)
RNC RN6.0 2.0
RNC RN7.0
This parameter indicates whether the
inter-frequency neighbour cell is included
in the System Information Block
11&12&18 for the cell selection and reselection procedures. The inter-frequency neighbour cell is included in the
system information when the value of the
parameter is "SIB". The inter-frequency
neighbour cell is included in the extended
system information when the value of the
parameter is "SIBbis".
The maximum number of inter-frequency neighbour cells that can be
included in the System Information Block
11&12&18 is 32. The neighbouring cells
can be distributed to up to two FDD
carriers (ref. 3GPP TS 25.133).
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47. When HCS is used, the
capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which are included in the System
Information, exceeds the physical size of
SIB data, the NBAP interface is not able
to pack the neighbour cell information
into the SIB data and the scheduling of
the system information blocks fails. The
cell is blocked by the system and an
alarm 7771 WCDMA CELL OUT OF USE
(BCCH scheduling error) is reported for
the cell.
This parameter indicates whether the
inter-frequency neighbour cell is included
in the System Information Block
11&12&18 for the cell selection and reselection procedures. This parameter
also indicates whether the inter-frequency neighbour cell is monitored for
the inter-frequency handover in
CELL_DCH state of connected mode.
The inter-frequency neighbour cell is
included in the system information when
the value of the parameter is "For SIB
and CELL DCH meas" or "For SIB only".
The inter-frequency neighbour cell is
included in the extended system information when the value of the parameter is
"For SIBbis and CELL DCH meas" or
"For SIBbis only".
The inter-frequency neighbour cell is
monitored for the inter-frequency
handover regardless of the value of the
parameter AdjiSIB if the value of the
RNFC parameter FemtoHandoverControl is "Disabled". If the value of the RNFC
parameter FemtoHandoverControl is
"Enabled":
- the inter-frequency neighbour cell
is monitored for the inter-frequency
handover if the value of the parameter
AdjiSIB is set to "For CELL DCH meas
only", "For SIB and CELL DCH meas" or
"For SIBbis and CELL DCH meas".
- the inter-frequency neighbour cell
is not monitored for the inter-frequency
handover if the value of the parameter
AdjiSIB is set to "For SIB only" or "For
SIBbis only".
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
Note: The parameter AdjiSIB does not
affect inter-frequency measurements in
CELL_DCH state of connected mode.
That is, all inter-frequency neighbour
cells are monitored for the inter-frequency handover regardless of the value
of the parameter AdjiSIB.
The maximum number of inter-frequency
neighbour cells that can be included in
the System Information Block 11&12&18
is 32. The neighbouring cells can be distributed to up to two FDD carriers (ref.
3GPP TS 25.133).
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47 when all cell re-selection
parameters are broadcasted. When HCS
is used, the capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which are included in the System
Information, exceeds the physical size of
SIB data, the NBAP interface is not able
to pack the neighbour cell information
into the SIB data and the scheduling of
the system information blocks fails. The
cell is blocked by the system and an
alarm 7771 WCDMA CELL OUT OF USE
(BCCH scheduling error) is reported for
the cell.
Range and step
0 (No), 1 (SIB), 2 (SIBbis)
0 (For CELL DCH meas only), 1 (For SIB
and CELL DCH meas), 2 (For SIBbis and
CELL DCH meas), 3 (For SIB only), 4
(For SIBbis only)
Default value notes
The inter-frequency neighbour cell is
included in the SIB.
The inter-frequency neighbour cell is
included in the SIB and monitored for the
inter-frequency handover.
DN00211177
Issue 12B
Id:0900d805809da32a
281
Summary of changes
1.2.3.4
Field
Description
1.2.3.5
Field
Description
1.2.3.6
Field
Description
282
WCDMA Radio Network Configuration Parameters
AdjiMCC (Mobile Country Code)
RNC RN6.0 2.0
RNC RN7.0
An inter-frequency neighbour cell is identified with UTRAN Cell Identifier which is
composed of Global RNC Identifier and
Cell Identifier. Furthermore, Global RNC
Identifier is composed of RNC Identifier
and PLMN Identifier, which in turn
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJI objects is required.
An inter-frequency neighbour cell is identified with UTRAN Cell Identifier which is
composed of Global RNC Identifier and
Cell Identifier. Furthermore, Global RNC
Identifier is composed of RNC Identifier
and PLMN Identifier, which in turn
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
AdjiMNC (Mobile Network Code)
RNC RN6.0 2.0
RNC RN7.0
An inter-frequency neighbour cell is identified with UTRAN Cell Identifier, which is
composed of Global RNC Identifier and
Cell Identifier. Furthermore, Global RNC
Identifier is composed of RNC Identifier
and PLMN Identifier, which in turn
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJI objects is required.
An inter-frequency neighbour cell is identified with UTRAN Cell Identifier, which is
composed of Global RNC Identifier and
Cell Identifier. Furthermore, Global RNC
Identifier is composed of RNC Identifier
and PLMN Identifier, which in turn
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
AdjiMNCLength (Mobile Network Code Length)
RNC RN6.0 2.0
RNC RN7.0
The parameter defines whether 2 or 3
digits are used in the Mobile Network
Code (MNC).
When this parameter is modified, also
the value of the MNC used by the system
is always changed.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJI objects is required.
The parameter defines whether 2 or 3
digits are used in the Mobile Network
Code (MNC).
When this parameter is modified, also
the value of the MNC used by the system
is always changed.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.3.7
AdjiRNCid (RNC Identifier)
Field
Description
1.2.4
1.2.4.1
RNC RN6.0 2.0
RNC RN7.0
An inter-frequency neighbor cell is identified with UTRAN Cell Identifier, which is
composed of Global RNC Identifier and
Cell Identifier. Global RNC Identifier is
composed of PLMN Identifier and RNC
Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC,
WCEL, and ADJI objects is required.
For RAN 2054 feature “Extension of
RNC ids “ only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
An inter-frequency neighbor cell is identified with UTRAN Cell Identifier, which is
composed of Global RNC Identifier and
Cell Identifier. Global RNC Identifier is
composed of PLMN Identifier and RNC
Identifier.
For RAN 2054 feature “Extension of
RNC ids “ only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
ADJL
AdjLEARFCN (E-UTRA Absolute Radio Frequency Channel
Number)
Field
RNC RN6.0 2.0
Related parameters
1.2.5
1.2.5.1
Field
Description
DN00211177
Issue 12B
Summary of changes
RNC RN7.0
SmartLTELayeringEnabled of WCEL The system prevents removal of the last
LTE neighbor if the Smart LTE Layering
feature is activated to the cell.
ADJS
AdjsCI (Cell Identifier)
RNC RN6.0 2.0
RNC RN7.0
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJS objects is required.
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier.
Id:0900d805809da32a
283
Summary of changes
1.2.5.2
Field
WCDMA Radio Network Configuration Parameters
RTWithHSDPAHopsIdentifier (HSDPA HOPS identifier for speechservices)
RNC RN6.0 2.0
RNC RN7.0
Full Name
HSDPA HOPS identifier for AMR multiservice
HSDPA HOPS identifier for speechservices
Description
This parameter identifies the parameter
set (HOPS object) controlling intra-frequency handovers of a user having HSDSCH allocated simultaneously with
AMR speech CS RAB.
This parameter identifies the parameter
set (HOPS object) controlling intra-frequency handovers of a user having HSDSCH allocated simultaneously with
AMR speech CS RAB or user having
push to talk allocated on HS-DSCH.
Related parameters
HOPSId of HOPS - Parameter must point
to the existing HOPSId.
HOPSId of HOPS - Parameter must point
to the existing HOPSId.
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and Intra-Frequency
Adjacency (ADJS) parent HSDPAenabled are set to enabled, special value
'Not defined' is not allowed.
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and Intra-Frequency
Adjacency (ADJS) parent HSDPAenabled are set to enabled, special value
'Not defined' is not allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and Intra-Frequency Adjacency (ADJS) parent
HSDPAenabled are set to enabled,
special value 'Not defined' is not allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and Intra-Frequency Adjacency (ADJS) parent
HSDPAenabled are set to enabled,
special value 'Not defined' is not allowed.
PTTEnabled of RNFC - If use of HSDPA
is enabled for PTT with the parameter
PTTEnabled (value > 1) and Intra-Frequency Adjacency (ADJS) parent HSDPAenabled are set to enabled, special
value 'Not defined' is not allowed.
Related features
284
HSDPA (optional) AND HSDPA with
HSDPA (optional) AND ( HSDPA with
Simultaneous AMR Voice Call (optional) Simultaneous AMR Voice Call (optional)
OR Optimised push to talk experience
(optional) )
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.5.3
Field
Description
DN00211177
Issue 12B
Summary of changes
AdjsSIB (Include in System Information)
RNC RN6.0 2.0
RNC RN7.0
The parameter determines whether the
intra-frequency neighbour cell is included
in the System Information Block
11&12&18 for the cell selection and reselection procedures. The intra-frequency neighbour cell is included in the
system information when the value of the
parameter is "SIB". The intra-frequency
neighbour cell is included in the extended
system information when the value of the
parameter is "SIBbis".
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47. When HCS is used, the
capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which are included in the System
Information, exceeds the physical size of
SIB data, the NBAP interface is not able
to pack the neighbour cell information
into the SIB data and the scheduling of
the system information blocks fails. The
cell is blocked by the system and an
alarm 7771 WCDMA CELL OUT OF USE
(BCCH scheduling error) is reported for
the cell.
Note: The parameter AdjsSIB does
not affect intra-frequency measurements
in CELL_DCH state of connected mode.
That is, all intra-frequency neighbour
cells are monitored for the soft(er)
handover regardless of the value of the
parameter AdjsSIB.
The parameter determines whether the
intra-frequency neighbour cell is included
in the System Information Block
11&12&18 for the cell selection and reselection procedures. The parameter
also determines whether the intra-frequency neighbour cell is monitored for
the soft(er) handover in CELL_DCH state
of connected mode. The intra-frequency
neighbour cell is included in the system
information when the value of the parameter is "For SIB and CELL DCH meas" or
"For SIB only". The intra-frequency
neighbour cell is included in the extended
system information (SIB11bis) when the
value of the parameter is "For SIBbis and
CELL DCH meas" or "For SIBbis only".
Information included in SIB11bis is not
included in SIB12. SIB12 contains the
cell information which is included in
SIB11.
The intra-frequency neighbour cell is
monitored for the soft(er) handover
regardless of the value of the parameter
AdjsSIB if the value of the RNFC parameter FemtoHandoverControl is "Disabled". If the value of the RNFC
parameter FemtoHandoverControl is
"Enabled":
- the intra-frequency neighbour cell
is monitored for the soft(er) handover if
the value of the parameter AdjsSIB is set
to "For CELL DCH meas only", "For SIB
and CELL DCH meas" or "For SIBbis and
CELL DCH meas".
- the intra-frequency neighbour cell
is not monitored for the soft(er) handover
if the value of the parameter AdjsSIB is
set to "For SIB only" or "For SIBbis only".
Id:0900d805809da32a
285
Summary of changes
Field
WCDMA Radio Network Configuration Parameters
RNC RN6.0 2.0
RNC RN7.0
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47 when all cell re-selection
parameters are broadcasted. When HCS
is used, the capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which are included in the System
Information, exceeds the physical size of
SIB data, the NBAP interface is not able
to pack the neighbour cell information
into the SIB data and the scheduling of
the system information blocks fails. The
cell is blocked by the system and an
alarm 7771 WCDMA CELL OUT OF USE
(BCCH scheduling error) is reported for
the cell.
Range and step
0 (No), 1 (SIB), 2 (SIBbis)
0 (For CELL DCH meas only), 1 (For SIB
and CELL DCH meas), 2 (For SIBbis and
CELL DCH meas), 3 (For SIB only), 4
(For SIBbis only)
Default value notes
The intra-frequency neighbour cell is
included in the System Information.
The intra-frequency neighbour cell is
included in the System Information and
monitored for the soft(er) handover.
286
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.5.4
Field
Description
1.2.5.5
Field
Description
1.2.5.6
Field
Description
DN00211177
Issue 12B
Summary of changes
AdjsMCC (Mobile Country Code)
RNC RN6.0 2.0
RNC RN7.0
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier. Furthermore, the Global RNC Identifier is
composed of the PLMN Identifier, which
consists of the Mobile Country Code
(MCC), the Mobile Network Code (MNC),
and the RNC Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJS objects is required.
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier. Furthermore, the Global RNC Identifier is
composed of the PLMN Identifier, which
consists of the Mobile Country Code
(MCC), the Mobile Network Code (MNC),
and the RNC Identifier.
AdjsMNC (Mobile Network Code)
RNC RN6.0 2.0
RNC RN7.0
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier. Furthermore, the Global RNC Identifier is
composed of the PLMN Identifier, which
consists of the Mobile Country Code
(MCC), the Mobile Network Code (MNC),
and the RNC Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJS objects is required.
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier. Furthermore, the Global RNC Identifier is
composed of the PLMN Identifier, which
consists of the Mobile Country Code
(MCC), the Mobile Network Code (MNC),
and the RNC Identifier.
AdjsMNCLength (Mobile Network Code Length)
RNC RN6.0 2.0
RNC RN7.0
The parameter defines whether 2 or 3
digits are used in the Mobile Network
Code (MNC).
When this parameter is modified also
the MNC value used by the system is
always changed.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJS objects is required.
The parameter defines whether 2 or 3
digits are used in the Mobile Network
Code (MNC).
When this parameter is modified also
the MNC value used by the system is
always changed.
Id:0900d805809da32a
287
Summary of changes
1.2.5.7
WCDMA Radio Network Configuration Parameters
AdjsRNCid (RNC Identifier)
Field
Description
1.2.6
1.2.6.1
Field
RNC RN6.0 2.0
RNC RN7.0
An intra-frequency neighbor cell is identified with the UTRAN Cell Identifier, which
is composed of the Global RNC Identifier
and the Cell Identifier. The Global RNC
Identifier is composed of the PLMN Identifier and the RNC Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC,
WCEL, and ADJS objects is required.
For RAN 2054 feature "Extension of
RNC ids" only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
An intra-frequency neighbor cell is identified with the UTRAN Cell Identifier, which
is composed of the Global RNC Identifier
and the Cell Identifier. The Global RNC
Identifier is composed of the PLMN Identifier and the RNC Identifier.
For RAN 2054 feature "Extension of
RNC ids" only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
CBCI
CBCIPaddress (IP address of the CBC)
RNC RN6.0 2.0
RNC RN7.0
Description
CBC-IP address for the Cell Broadcast
Service. Each CBC can have a maximum
of four different CBC-IP addresses to
control Cell Broadcast Service.
Examples:
IPv4, 255.255.255.255, 1.1.1.1
IPv6,
FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FF
FF:FFFF
CBC-IP address for the Cell Broadcast
Service. Each CBC can have maximum
four different CBC-IP addresses to
control Cell Broadcast Service.
Examples:
IPv4, 255.255.255.255, 1.1.1.1
Range and step
7..39 characters
7..15 characters
Default value notes
The default value is not possible
Default value is not possible
Related features
Service Area Broadcast (optional)
Service Area Broadcast (optional) OR
SAB Support with 2 SCCPCHs (optional)
1.2.6.2
Field
Description
288
CBCIPaddrType (Type of CBC IP address)
RNC RN6.0 2.0
RNC RN7.0
Indicates the used IP-address (Ipv4 or
Ipv6). Only one type of IP-address is
allowed to be used for one CBC.
Indicates the used IP-address (Ipv4).
Only one type of IP-address is allowed to
be used for one CBC.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
Range and step
0 (IP v4), 1 (IP v6)
0 (IP v4)
Related features
Service Area Broadcast (optional)
Service Area Broadcast (optional) OR
SAB Support with 2 SCCPCHs (optional)
1.2.7
1.2.7.1
CMOB
CMOBId (Congestion Management Group Identifier)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
This parameter uniquely identifies the
CMOB (Congestion Management Group)
within the RNC. Parameter values from 4
to 13 are available for the user. Values 1
to 3 are reserved for system usage.
This parameter uniquely identifies the
CMOB (Congestion Management Group)
within the RNC. Parameter values from 4
to 23 are available for the user. Values 1
to 3 are reserved for system usage.
Range and step
1..13, step 1
1..23, step 1
1.2.7.2
TrafficRestriction (Traffic Restriction)
Field
RNC RN6.0 2.0
Range and step
1.2.8
1.2.8.1
Field
Related features
1.2.8.2
Field
Range and step
DN00211177
Issue 12B
0 (disabled), 1 (enabled)
RNC RN7.0
0 (Disabled), 1 (Enabled)
COCO
AAL2TP/AAL2SignLinkVCI (AAL2 signalling link Virtual Channel
Identifier)
RNC RN6.0 2.0
RNC RN7.0
Flexible connection of VPCs for WBTS
object in RNC (optional)
AAL2SignLinkTP/AAL2SigEarlyPacketDiscard (AAL2 SL Early
Packet Discard)
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
RNC RN7.0
0 (Disabled), 1 (Enabled)
Id:0900d805809da32a
289
Summary of changes
1.2.8.3
Field
Range and step
1.2.8.4
Field
Range and step
1.2.8.5
Field
Range and step
1.2.8.6
Field
Related parameters
WCDMA Radio Network Configuration Parameters
AAL2SignLinkTP/AAL2SigPartialPacketDiscard (AAL2 SL Partial
Packet Discard)
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
Field
Related features
1.2.8.8
Field
Related features
290
0 (Disabled), 1 (Enabled)
CNBAPTP/CNBAPEarlyPacketDiscard (C-NBAP Early Packet
Discard)
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
RNC RN7.0
0 (Disabled), 1 (Enabled)
CNBAPTP/CNBAPPartialPacketDiscard (C-NBAP Partial Packet
Discard)
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
RNC RN7.0
0 (Disabled), 1 (Enabled)
CNBAPTP/CNBAPCDVT01Ing (C-NBAP VCLtp CDVT ingress)
RNC RN6.0 2.0
RNC RN7.0
CalculateCDVT of COCO - The parame- CalculateCDVT of COCO - The parameter is mandatory if the CalculateCDVT is ter is mandatory if the CalculateCDVT is
disabled for the COCO.
disabled for the COCO.
CreateATMTP of COCO - The parameter
is mandatory if the CreateATMTP is
disabled for the COCO.
1.2.8.7
RNC RN7.0
CreateATMTP of COCO - The parameter
is mandatory if the CreateATMTP is
enabled for the COCO.
CNBAPTP/CNBAPVCI (C-NBAP Virtual Channel Identifier)
RNC RN6.0 2.0
RNC RN7.0
Flexible connection of VPCs for WBTS
object in RNC (optional)
CNBAPTP/CNBAPVPI (C-NBAP Virtual Path Identifier)
RNC RN6.0 2.0
RNC RN7.0
Flexible connection of VPCs for WBTS
object in RNC (optional)
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.8.9
Field
Range and step
1.2.8.10
Field
Related features
1.2.8.11
Field
Related features
1.2.8.12
Field
Range and step
1.2.8.13
Field
Description
1.2.8.14
Field
Related features
DN00211177
Issue 12B
Summary of changes
DNBAPTP/DNBAPEarlyPacketDiscard (D-NBAP Early Packet
Discard)
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
RNC RN7.0
0 (Disabled), 1 (Enabled)
DNBAPTP/DNBAPVCI (D-NBAP Virtual Channel Identifier)
RNC RN6.0 2.0
RNC RN7.0
Flexible connection of VPCs for WBTS
object in RNC (optional)
DNBAPTP/DNBAPVPI (D-NBAP Virtual Path Identifier)
RNC RN6.0 2.0
RNC RN7.0
Flexible connection of VPCs for WBTS
object in RNC (optional)
DNBAPTP/DNBAPPartialPacketDiscard (DNBAP Partial Packet
Discard)
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
RNC RN7.0
0 (Disabled), 1 (Enabled)
VPLTP (Virtual Path Link termination point)
RNC RN6.0 2.0
RNC RN7.0
The Virtual Path Link termination point
parameters of the COCO object.
The Virtual Path Link termination point
parameters of the COCO object. One
instance shall be configured. With license
“Flexible connection of VPCs for WBTS
object in RNC” more than one instances
can be configured.
VPLTP/VPLTPCDVT01Egr (VPLtp CDVT egress)
RNC RN6.0 2.0
RNC RN7.0
Flexible connection of VPCs for WBTS
object in RNC (optional)
Id:0900d805809da32a
291
Summary of changes
1.2.8.15
WCDMA Radio Network Configuration Parameters
VPLTP/VPLTPAdmState (VPLtp effective administrative state)
Field
RNC RN6.0 2.0
Related features
1.2.8.16
Flexible connection of VPCs for WBTS
object in RNC (optional)
VPLTP/VPLTPPCR01Egr (VPLtp PCR egress)
Field
RNC RN6.0 2.0
Related features
1.2.8.17
RNC RN7.0
Flexible connection of VPCs for WBTS
object in RNC (optional)
VPLTP/VPLTPTrafficShaping (VPLtp VP level traffic shaping)
Field
RNC RN6.0 2.0
Related features
1.2.9
1.2.9.1
Field
RNC RN7.0
Flexible connection of VPCs for WBTS
object in RNC (optional)
FMCG
IMSIbasedGsmHo (IMSI Based GSM HO)
RNC RN6.0 2.0
Related parameters
292
RNC RN7.0
RNC RN7.0
ICREnabled of WBTS - FMCGIMSIBasedGSMHo is not allowed to be
set with 0 (This HO type is not allowed), if
WBTS- ICREnabled parameter is set as
“Enabled”.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.10
1.2.10.1
HOPG
AdjgPriorityCoverage (Ncell Priority for Coverage HO)
Field
Description
1.2.11
1.2.11.1
Field
Description
DN00211177
Issue 12B
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
If there are several GSM neighbour cells
which meet the required radio link properties for the coverage (or quality) reason
handover at the same time, the RNC
ranks the potential target cells according
to priority levels and selects the highest
ranked GSM neighbour cell to be the
target cell.
The priority level of a GSM neighbour
cell is controlled by the parameter GSMncellPriorityCoverage. The range of the
parameter varies from zero to 7. Zero is
the lowest and 7 the highest priority level.
If there are several GSM neighbour cells
which meet the required radio link properties for the coverage (or quality) reason
handover at the same time, the RNC
ranks the potential target cells according
to priority levels and selects the highest
ranked GSM neighbour cell to be the
target cell.
The priority level of a GSM neighbour
cell is controlled by this parameter. The
range of the parameter varies from zero
to 7. Zero is the lowest and 7 the highest
priority level.
HOPI
AdjiPriorityCoverage (Ncell Priority for Coverage IFHO)
RNC RN6.0 2.0
RNC RN7.0
The inter-frequency measurement procedure measures one frequency at a time.
If there is more than one carrier frequency to be measured, the RNC selects
a subset of inter-frequency neighbour
cells (having the same UTRA RF channel
number) which are measured first.
In case of a coverage reason handover, the measurement order is controlled by the parameter
InterFreqNcellPriorityCoverage. The
range of the parameter varies from zero
to 7. Zero is the lowest and 7 the highest
priority level.
The inter-frequency measurement procedure measures one frequency at a time.
If there is more than one carrier frequency to be measured, the RNC selects
a subset of inter-frequency neighbour
cells (having the same UTRA RF channel
number) which are measured first.
In case of a coverage reason handover, the measurement order is controlled by this parameter. The range of
the parameter varies from zero to 7. Zero
is the lowest and 7 the highest priority
level.
Id:0900d805809da32a
293
Summary of changes
1.2.11.2
WCDMA Radio Network Configuration Parameters
AdjiPriorityQuality (Ncell Priority for Quality IFHO)
Field
Description
1.2.12
1.2.12.1
RNC RN6.0 2.0
RNC RN7.0
The inter-frequency measurement procedure measures one frequency at a time.
If there is more than one carrier frequency to be measured, the RNC selects
a subset of inter-frequency neighbour
cells (having the same UTRA RF channel
number) which are measured first.
In case of a quality reason handover,
the measurement order is controlled by
the parameter InterFreqNcellPriorityQuality. The range of the parameter
varies from zero to 7. Zero is the lowest
and 7 the highest priority level.
The inter-frequency measurement procedure measures one frequency at a time.
If there is more than one carrier frequency to be measured, the RNC selects
a subset of inter-frequency neighbour
cells (having the same UTRA RF channel
number) which are measured first.
In case of a quality reason handover,
the measurement order is controlled by
this parameter. The range of the parameter varies from zero to 7. Zero is the
lowest and 7 the highest priority level.
HOPS
HSDPAAvailabilityIur (HSDPA availability of the neighbouring
DRNC cell)
Field
Related parameters
RNC RN6.0 2.0
RNC RN7.0
CSAMRModeSET of VCEL - HSDPA
availability check is valid if HSDPA over
Iur is enabled.
HSPAOverIur of IUR - HSDPA availability
check is valid if HSPA over Iur is enabled.
HSDPAenabled of VCEL - HSDPA availHSPAOverIur of IUR - HSDPA availability ability check is valid if HSDPA over Iur is
check is valid if HSPA over Iur is enabled. enabled.
1.2.13
1.2.13.1
Field
Related features
1.2.13.2
Field
Related features
294
IPQM
BackgroundTCToDSCP (Background TC to DSCP mapping)
RNC RN6.0 2.0
RNC RN7.0
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
IPQMChangeOrigin (Change origin)
RNC RN6.0 2.0
RNC RN7.0
IP based Iu-CS (optional) OR IP based
Iu-PS (optional)
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.13.3
Field
Related features
1.2.13.4
Field
Related features
1.2.13.5
Field
Related features
1.2.13.6
Field
Related features
1.2.13.7
Field
Summary of changes
ConversationalTCToDSCP (Conversational TC to DSCP mapping)
RNC RN6.0 2.0
RNC RN7.0
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
InteractiveTHP1TCToDSCP (Interactive THP1 TC to DSCP mapping)
RNC RN6.0 2.0
RNC RN7.0
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
InteractiveTHP2TCToDSCP (Interactive THP2 TC to DSCP mapping)
RNC RN6.0 2.0
RNC RN7.0
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
InteractiveTHP3TCToDSCP (Interactive THP3 TC to DSCP mapping)
RNC RN6.0 2.0
RNC RN7.0
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
IPQMId (IP Qos Management Identifier)
RNC RN6.0 2.0
Related parameters
RNC RN7.0
IPQMIdCS of IUCSIP - The IPQM object
cannot be deleted in case IUCSIP object
refers to it.
IPQMIdPS of IUPSIP - The IPQM object
cannot be deleted in case IUPSIP object
refers to it.
Related features
DN00211177
Issue 12B
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
Id:0900d805809da32a
295
Summary of changes
1.2.13.8
WCDMA Radio Network Configuration Parameters
StreamingTCToDSCP (Streaming TC to DSCP mapping)
Field
Related features
1.2.14
1.2.14.1
Field
RNC RN6.0 2.0
RNC RN7.0
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
IUCS
NetworkInd (Network indicator)
RNC RN6.0 2.0
Related parameters
RNC RN7.0
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
1.2.14.2
Field
Range and step
296
CNDomainVersion (Release version of Core Network)
RNC RN6.0 2.0
RNC RN7.0
1 (R99), 2 (Rel4), 3 (Rel5), 4 (Rel6), 5
(Rel7), 6 (Rel8), 7 (Rel9)
1 (R99), 2 (Rel4), 3 (Rel5), 4 (Rel6), 5
(Rel7), 6 (Rel8), 7 (Rel9), 8 (Rel10), 9
(Rel11), 10 (Rel12)
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.14.3
Field
Description
Related parameters
Summary of changes
SignPointCode (Signalling point code)
RNC RN6.0 2.0
RNC RN7.0
The code that uniquely identifies the signalling point in the signalling network.
The parameter is not modifiable if the
core network is active. Parameter modification terminates ongoing calls.
The code identifies the signalling point in
the signalling network.
Combination of NetworkInd and SignPointCode uniquely identifies a Signalling Point.
The parameter is not modifiable if the
core network is active. Parameter modification terminates ongoing calls.
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
DN00211177
Issue 12B
Id:0900d805809da32a
297
Summary of changes
1.2.15
1.2.15.1
WCDMA Radio Network Configuration Parameters
IUCSIP
DestIPAddressCS (IP address for the IUCS destination subnet)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
The DestIPAddressCS attribute with the
IPNetmaskCS parameter forms a destination IP subnet definition for the Iu-CS
user plane connections. The RNC
performs the IP Based Route id reference
selection for the new Iu-CS connection in
between the destination IP subnet and
the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUCSIP
object instance needed under the IUCS
object instance. Example IPv4: 0.0.0.0 / 0
-> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUCSIP objects under the IUCS.
Example IPv4: IUCSIP#1 192.168.0.0 /
28 -> IP Based Route id y, IUCSIP#2
192.168.0.16 / 28 -> IP Based Route id z.
This parameter is used with IP over
Ethernet Iu-CS connectivity in cRNC and
mcRNC. In case of I-HSPA the parameter is always used for the Iu-CS connectivity.
The DestIPAddressCS attribute with the
IPNetmaskCS parameter forms a destination IP subnet definition for the Iu-CS
user plane connections. The RNC
performs the IP Based Route id reference
selection for the new Iu-CS connection in
between the destination IP subnet and
the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUCSIP
object instance needed under the IUCS
object instance. Example IPv4: 0.0.0.0 / 0
-> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUCSIP objects under the IUCS.
Example IPv4: IUCSIP#1 192.168.0.0 /
28 -> IP Based Route id y, IUCSIP#2
192.168.0.16 / 28 -> IP Based Route id z.
This parameter is used with IP over
Ethernet Iu-CS connectivity in cRNC and
mcRNC. In case of Flexi Direct RNC the
parameter is always used for the Iu-CS
connectivity.
Default value
-
0.0.0.0
Default value notes
298
Referred IP Based Route gets selected
regardless of the IP address signaled by
the CN.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Related parameters
1.2.15.2
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
IPNetmaskCS of IUCSIP - The IPNetmaskCS with the DestIPAddressCS attribute form the destination IP subnet
definition.
IPNetmaskCS of IUCSIP - The IPNetmaskCS together with the DestIPAddressCS attribute form the destination IP
subnet which must be unique for each
IUCSIP object.
IPBasedRouteIdCS (IP Based Route Identifier for IUCS)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
The IPBasedRouteId refers to the logical
IP Based Route entity configured in the
IP layer with MML or through the IP Plan
interface. The IP Based Route configured
for the Iu-CS interface is used for the user
plane connections towards the Iu-CS CN
element controlling the interface unit and
port selection along with the source IP
address and the UDP port selection. This
parameter is applied when the IP over
Ethernet transport option is used.
The IPBasedRouteId refers to the logical
IP Based Route entity configured in the
IP layer with MML/SCLI or through the IP
Plan interface. The IP Based Route configured for the Iu-CS interface is used for
the user plane connections towards the
Iu-CS CN element controlling the interface unit and port selection along with the
source IP address and the UDP port
selection. This parameter is applied when
the IP over Ethernet transport option is
used.
Default value
0
Default value notes
Value not defined.
Special value
0
DN00211177
Issue 12B
Id:0900d805809da32a
299
Summary of changes
1.2.15.3
Field
Description
WCDMA Radio Network Configuration Parameters
IPNetmaskCS (IP netmask for the IUCS destination subnet)
RNC RN6.0 2.0
RNC RN7.0
The IPNetmaskCS with the DestIPAddressCS attribute forms a destination IP
subnet definition for the Iu-CS user plane
connections. The RNC performs the IP
Based Route id reference selection for
the new Iu-CS connection in between the
destination IP subnet and the destination
IP address (RANAP:Transport Layer
Address) that is received at the RAB
assignment request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUCSIP
object instance needed under the IUCS
object instance. Example IPv4: 0.0.0.0 /
0.0.0.0 -> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUCSIP objects under the IUCS.
Example IPv4: IUCSIP#1 192.168.0.0 /
255.255.255.240 -> IP Based Route id y,
IUCSIP#2 192.168.0.16 /
255.255.255.240 -> IP Based Route id z.
This parameter is used with IP over
Ethernet Iu-CS connectivity in cRNC and
mcRNC. In case of I-HSPA the parameter is always used for the Iu-CS connectivity.
The IPNetmaskCS with the DestIPAddressCS attribute forms a destination IP
subnet definition for the Iu-CS user plane
connections. The RNC performs the IP
Based Route id reference selection for
the new Iu-CS connection in between the
destination IP subnet and the destination
IP address (RANAP:Transport Layer
Address) that is received at the RAB
assignment request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUCSIP
object instance needed under the IUCS
object instance. Example IPv4: 0.0.0.0 /
0.0.0.0 -> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUCSIP objects under the IUCS.
Example IPv4: IUCSIP#1 192.168.0.0 /
255.255.255.240 -> IP Based Route id y,
IUCSIP#2 192.168.0.16 /
255.255.255.240 -> IP Based Route id z.
This parameter is used with IP over
Ethernet Iu-CS connectivity in cRNC and
mcRNC. In case of Flexi Direct RNC the
parameter is always used for the Iu-CS
connectivity.
Default value notes
Related parameters
300
Referred IP Based Route gets selected
regardless of the IP address signaled by
the CN
DestIPAddressCS of IUCSIP - The
IPNetmaskCS with the DestIPAddressCS attribute form the destination IP
subnet definition.
Id:0900d805809da32a
DestIPAddressCS of IUCSIP - The
IPNetmaskCS together with the DestIPAddressCS attribute form the destination IP subnet which must be unique for
each IUCSIP object.
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.15.4
Summary of changes
IPQMIdCS (IPQM object id for IuCS)
Field
RNC RN6.0 2.0
RNC RN7.0
Full Name
IPQM object id for IuItemCS
IPQM object id for IuCS
Description
The IPQM identification gives the reference to the IPQM object used for the CS
CN. The IPQM object defines the UMTS
traffic class to DSCP mapping to be used
for the IP connections at the Iu interface.
IPQM reference needs to be given in the
CN definitions if the IP transport is used
at the interface towards the corresponding CN element.
This parameter is used only with CN
nodes that use the IP over Ethernet as
transmission technology.
The IPQM identification gives the reference to the IPQM object used for the CS
CN. The IPQM object defines the UMTS
traffic class to DSCP mapping to be used
for the IP connections at the Iu interface.
IPQM reference needs to be given in the
CN definitions if the IP transport is used
at the interface towards the corresponding CN element. The referred IPQM
instance has to exist in the system before
IUCSIP is created.
This parameter is used only with CN
nodes that use the IP over Ethernet as
transmission technology.
Range and step
0..8, step 1
1..8, step 1
Default value
0
Default value notes
0 means that the IPQM reference is not
given and default values are used.
Related parameters
1.2.16
1.2.16.1
IPQMId of IPQM - The IPQM object
instance referred by IPQMIdCS has to
exist.
IUO
PLMNid/MCC (Mobile Country Code)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
Unique country identification. MCC
consists of three digits. MCC together
with MNC identifies the PLMN uniquely
(globally).
Unique country identification. MCC
consists of three digits. MCC together
with MNC identifies the PLMN uniquely
(globally).
MCC cannot be modified in case
it is mapped to any WCEL or CBCI
Default value
65535
Default value notes
Not defined
Special value
65535
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
301
Summary of changes
1.2.16.2
WCDMA Radio Network Configuration Parameters
PLMNid/MNC (Mobile Network Code)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
Unique network identification within
country. MNC consists of two or three
digits. MNC together with MCC identifies
the PLMN uniquely (globally).
Unique network identification within
country. MNC consists of two or three
digits. MNC together with MCC identifies
the PLMN uniquely (globally).
MNC cannot be modified in case
it is mapped to any WCEL or CBCI
Default value
65535
Default value notes
Not defined
Special value
65535
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
1.2.16.3
PLMNid/MNCLength (Mobile Network Code Length)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
This parameter defines whether 2 or 3
digits are used in Mobile Network Code.
When this parameter is modified
also the value of MNC used by system is
always changed.
This parameter defines whether 2 or 3
digits are used in Mobile Network Code.
This parameter cannot be modified
in case IUO-PLMNid is mapped to any
WCEL or CBCI.
When this parameter is modified
also the value of MNC used by system is
always changed.
Default value
2
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
1.2.16.4
Field
Description
NRILengthForCSCN (NRI length for CS Core Networks)
RNC RN6.0 2.0
RNC RN7.0
This parameter defines the length (in bits)
of the NRI parameter to be used in the CS
CN selection.
This parameter defines the length (in bits)
of the NRI parameter to be used in the CS
CN selection.
Note that this parameter is visible
only when CS licenses of IuFlex and/or
Multi-Operator Core Network is/are activated. When none of the licenses is activated, the parameter value is handled as
0 in L3 SW.
302
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Related features
1.2.16.5
Field
Description
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
NRILengthForPSCN (NRI length for PS Core Networks)
RNC RN6.0 2.0
RNC RN7.0
This parameter defines the length (in bits)
of the NRI parameter to be used in the PS
CN selection.
This parameter defines the length (in bits)
of the NRI parameter to be used in the PS
CN selection.
IuOperator => NRILengthForPSCN
Note that this parameter is visible
only when PS licenses of IuFlex and/or
Multi-Operator Core Network is/are activated. When none of the licenses is activated, the parameter value is handled as
0 in L3 SW.
Related features
1.2.16.6
Field
Description
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
NullNRIForCSPool (Null NRI value for CS Pool)
RNC RN6.0 2.0
RNC RN7.0
This parameter defines the MSC allocated NRI value to be used in load redistribution. The RNC's NAS node selection
function uses load balancing in routing for
all the UEs using Null NRI.
This parameter defines the operator Null
NRI value for CS domain to select a
certain operator in a Multi Operator Core
Network.
NOTE: All operators must have theirspecific Null NRI.
NOTE: Null NRI value cannot be
given to any MSC of the pool.
NOTE: Operator cannot have same
null-NRI as others.
Related features
DN00211177
Issue 12B
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
Multi-Operator Core Network (optional)
Id:0900d805809da32a
303
Summary of changes
1.2.16.7
Field
Description
WCDMA Radio Network Configuration Parameters
NullNRIForPSPool (Null NRI value for PS Pool)
RNC RN6.0 2.0
RNC RN7.0
This parameter defines the SGSN allocated NRI value to be used in load redistribution. The RNC's NAS node selection
function uses load balancing in routing for
all the UEs using Null NRI.
This parameter defines the operator Null
NRI value for PS domain to select a
certain operator in a Multi Operator Core
Network.
NOTE: All operators must have their
specific Null NRI.
NOTE: Null NRI value cannot be
given to any SGSN of the pool.
NOTE: Operator cannot have same
null-NRI as others.
Related parameters
NRIMaxForPSCN of IUPS NRIMinForPSCN of IUPS NullNRIForPSPool of IUO -
NRIMaxForPSCN of IUPS - The Null NRI
value cannot be given to any SGSN of
the pool.
NRIMinForPSCN of IUPS - The Null NRI
value cannot be given to any SGSN of
the pool.
NullNRIForPSPool of IUO - The operator
cannot have same null-NRI as the others.
Related features
304
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
Id:0900d805809da32a
Multi-Operator Core Network (optional)
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.16.8
Summary of changes
OperatorWeight (Operator Weight)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
This parameter defines the percentage
weight value of each operator in MultiOperator Core Network (MOCN).
Operator weight is used for the weighted
round robin method to select a CN operator. Load sharing among operators is
defined by configuring OperatorWeight.
Weight is divided among all operators
like:
OP1 50%
OP2 30%
OP3 20%
Weight value range is between 0 and
100. The total sum of every operator's
weight is 100 or 0.
If the weight value is 0 for all operators, it means that the equal load is
shared among all operators.
If the weight value is 100 for one
operator and all other operators are 0, it
means the operator with 100% load is the
default operator.
This parameter defines the weight value
of each operator in Multi-Operator Core
Network (MOCN). Operator weight is
used for the weighted round robin
method to select a CN operator. Load
sharing among operators is defined by
configuring OperatorWeight.
Weight is divided among all operators
like:
OP1 60
OP2 50
OP3 40
Thus the actual weight value used in
load sharing calculation for e.g. OP1
would be individual weigh value divided
by sum of weight values,
60/(60+50+40)=0.4. Weight value range
is between 0 and 100.If the weight value
is identical for all operators, it means that
the equal load is shared among all operators.
If the weight value is greater than 0
for one operator and all other operators
are 0, it means this one operator is the
default operator, getting the full load.
Unit
%
1.2.16.9
Field
Description
DN00211177
Issue 12B
PLMNid (PLMN identity)
RNC RN6.0 2.0
RNC RN7.0
A Public Land Mobile Network is uniquely
identified by its PLMN identity. PLMNid
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
PLMN identity is an optional parameter, but needs to be configured with
proper values when configuring the
MOCN feature.
This parameter is primary Public Land
Mobile Network ( PLMN ) identity of the
operator. A Public Land Mobile Network
is uniquely identified by its PLMN identity.
PLMN identity consists of Mobile Country
Code (MCC) and Mobile Network Code
(MNC).
PLMNId cannot be modified if it is
mapped to any WCEL or CBCI.
Id:0900d805809da32a
305
Summary of changes
WCDMA Radio Network Configuration Parameters
Field
Related parameters
RNC RN6.0 2.0
RNC RN7.0
CommonMCC of RNC - Common PLMN
id (CommonMCC and CommonMNC)
can't be the same as any PLMNid in
IuOperator
CommonMCC of RNC - Common PLMN
id (CommonMCC and CommonMNC)
can't be the same as any PLMNid in IUO
instances.
CommonMNC of RNC - Common PLMN
id (CommonMCC and CommonMNC)
can't be the same as any PLMNid in
IuOperator
CommonMNC of RNC - Common PLMN
id (CommonMCC and CommonMNC)
can't be the same as any PLMNid in IUO
instances.
SharedAreaPLMNid of IUO - SharedAreaPLMNid can't be the same as any
primary PLMNid in IUO instances.
Related features
1.2.16.10
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
SharedAreaPLMNid/SharedAreaMCC (Shared area Mobile Country
Code)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
The parameters Shared area mobile
country code and Shared area mobile
network code compose the identifier of a
PLMN to which the subscribers of the
partner operator can have access.
The parameters Shared area mobile
country code and Shared area mobile
network code compose the identifier of a
PLMN to which the subscribers of the
partner operator can have access.
These parameters cannot be
modified in case they are mapped to any
WCEL.
Related parameters
SharedAreaPLMNid of IUO -
Parameter relationships
-
Related features
IMSI Based Handover (optional)
1.2.16.11
Field
Description
306
IMSI Based Handover (optional) OR
Multi-Operator Core Network (optional)
SharedAreaPLMNid/SharedAreaMNC (Shared area Mobile Network
Code)
RNC RN6.0 2.0
RNC RN7.0
The parameters Shared area mobile
country code and Shared area mobile
network code compose the identifier of a
PLMN to which the subscribers of the
partner operator can have access.
The parameters Shared area mobile
country code and Shared area mobile
network code compose the identifier of a
PLMN to which the subscribers of the
partner operator can have access.
These parameters cannot be
modified in case they are mapped to any
WCEL
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Related features
1.2.16.12
Field
Summary of changes
RNC RN6.0 2.0
IMSI Based Handover (optional)
RNC RN7.0
IMSI Based Handover (optional) OR
Multi-Operator Core Network (optional)
SharedAreaPLMNid/SharedAreaMNClength (Shared area Mobile
Network Code Length)
RNC RN6.0 2.0
RNC RN7.0
Description
The parameter defines whether 2 or 3
digits are used in the shared area mobile
network code.
When modifying this parameter,
also the value of the MNC used by the
system is always changed.
The parameter defines whether 2 or 3
digits are used in the shared area mobile
network code.
When modifying this parameter,
also the value of the MNC used by the
system is always changed.
SharedAreaPLMNid cannot be
modified in case it is mapped to any
WCEL.
Related features
IMSI Based Handover (optional)
IMSI Based Handover (optional) OR
Multi-Operator Core Network (optional)
DN00211177
Issue 12B
Id:0900d805809da32a
307
Summary of changes
1.2.16.13
WCDMA Radio Network Configuration Parameters
SharedAreaPLMNid (Shared area PLMN identity)
Field
Description
RNC RN6.0 2.0
RNC RN7.0
The parameter uniquely identifies the
shared Public Land Mobile Network to
which the subscribers of the partner
operator can have access. The SharedAreaPLMNid consists of the Mobile
Country Code (MCC) and Mobile
Network Code (MNC).
This parameter is secondary Public Land
Mobile Network ( PLMN ) identity of the
operator. The parameter uniquely identifies the shared Public Land Mobile
Network to which the subscribers of the
partner operator can have access. The
SharedAreaPLMNid consists of the
Mobile Country Code (MCC) and Mobile
Network Code (MNC). In-case of IMSI
Based HO, Operator can configure
WCEL with SharedAreaPLMNid in
addition to primary PLMNid except when
MOCN or MORAN is configured.. Also
CBCI is associated with SharedAreaPLMNids in case of IMSI based HO
is activated without MORAN and MOCN.
SharedAreaPLMNids are configured
for MOCN in order to support the usage
of several PLMNIds in network. When
routing is based on IMSI and PLMNId in
IMSi matches one of the SharedAreaPLMNids, the UE can be routed to
the CN for which the primary PLMNId has
been configured.
SharedAreaPLMNId cannot be
modified if it is mapped to any WCEL.
Related parameters
Related features
1.2.17
1.2.17.1
Field
Related parameters
308
PLMNid of IUO - Shared area PLMNid
can't be same as any PLMNid in IUO
instances.
IMSI Based Handover (optional)
IMSI Based Handover (optional) OR
Multi-Operator Core Network (optional)
IUPS
PSCNNRI/NRIMaxForPSCN (Maximum value of NRI range for PS
Core routing)
RNC RN6.0 2.0
RNC RN7.0
CNDRXLength of IUPS - NRIMinForPSCN and NRIMaxForPSCN can be configured to have the same value, indicating
one NRI value instead of value range.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.17.2
Field
Related parameters
1.2.17.3
Field
Summary of changes
PSCNNRI/NRIMinForPSCN (Minimum value of NRI range for PS Core
routing)
RNC RN6.0 2.0
RNC RN7.0
CNDRXLength of IUPS - NRIMinForPSCN and NRIMaxForPSCN can be configured to have the same value, indicating
one NRI value instead of value range.
NetworkInd (Network indicator)
RNC RN6.0 2.0
Related parameters
RNC RN7.0
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
1.2.17.4
Field
Range and step
DN00211177
Issue 12B
CNDomainVersion (Release version of Core Network)
RNC RN6.0 2.0
RNC RN7.0
1 (R99), 2 (Rel4), 3 (Rel5), 4 (Rel6), 5
(Rel7), 6 (Rel8), 7 (Rel9)
1 (R99), 2 (Rel4), 3 (Rel5), 4 (Rel6), 5
(Rel7), 6 (Rel8), 7 (Rel9), 8 (Rel10), 9
(Rel11), 10 (Rel12)
Id:0900d805809da32a
309
Summary of changes
1.2.17.5
Field
WCDMA Radio Network Configuration Parameters
SignPointCode (Signalling point code)
RNC RN6.0 2.0
RNC RN7.0
Description
The code that uniquely identifies the signalling point in the signalling network.
The parameter is not modifiable if the
core network is active. Parameter modification terminates ongoing calls.
The code identifies the signaling point in
the signaling network.
Combination of NetworkInd and SignPointCode uniquely identifies a Signalling Point.
The parameter is not modifiable if the
core network is active. Parameter modification terminates ongoing calls.
Related parameters
NetworkInd of IUPS -
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
310
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.18
1.2.18.1
Summary of changes
IUPSIP
DestIPAddressPS (IP address for the IUPS destination subnet)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
The DestIPAddressPS attribute with the
IPNetmaskPS parameter forms a destination IP subnet definition for the Iu-PS
user plane connections (GTP tunnels).
The RNC performs the IP Based Route id
reference selection for the new Iu-PS
connection in between the destination IP
subnet and the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUPSIP
object instance needed under the IUPS
object instance. Example IPv4: 0.0.0.0 / 0
-> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUPSIP objects under the IUPS.
Example IPv4: IUPSIP#1 192.168.0.0 /
28 -> IP Based Route id y, IUPSIP#2
192.168.0.16 / 28 -> IP Based Route id z.
Note: This parameter is configured
in the following cases:
- IP over Ethernet transport option
with cRNC NPGE, mcRNC and I-HSPA
- IP over ATM option with an
cRNC/NPS1 based network interface
- Always used with I-HSPA Iu-PS
configuration
As an exception the parameter is not
used with cRNC GTPU/NIS HW based
Iu-PS interface.
The DestIPAddressPS attribute with the
IPNetmaskPS parameter forms a destination IP subnet definition for the Iu-PS
user plane connections (GTP tunnels).
The RNC performs the IP Based Route id
reference selection for the new Iu-PS
connection in between the destination IP
subnet and the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUPSIP
object instance needed under the IUPS
object instance. Example IPv4: 0.0.0.0 / 0
-> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUPSIP objects under the IUPS.
Example IPv4: IUPSIP#1 192.168.0.0 /
28 -> IP Based Route id y, IUPSIP#2
192.168.0.16 / 28 -> IP Based Route id z.
Note: This parameter is configured
in the following cases:
- IP over Ethernet transport option
with cRNC NPGE, mcRNC and Flexi
Direct RNC
- IP over ATM option with an
cRNC/NPS1 based network interface
- Always used with Flexi Direct RNC
Iu-PS configuration
As an exception the parameter is not
used with cRNC GTPU/NIS HW based
Iu-PS interface.
Default value
-
0.0.0.0
DN00211177
Issue 12B
Id:0900d805809da32a
311
Summary of changes
WCDMA Radio Network Configuration Parameters
Field
RNC RN6.0 2.0
Default value notes
Related features
1.2.18.2
RNC RN7.0
Referred IP Based Route gets selected
regardless of the IP address signaled by
the CN.
IP based Iu-PS (optional)
IP based Iu-PS (optional) OR Basic
functions (standard)
IPBasedRouteIdPS (IP Based Route Identifier for IUPS)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
The IPBasedRouteId refers to the logical
IP Based Route entity configured in the
IP layer with MML or via the IP Plan interface. The IP Based Route configured for
the Iu-PS interface is used for the user
plane connections towards the Iu-PS CN
element controlling the interface unit and
port selection along with the source IP
address and UDP port selection.
Note: This parameter is configured
when the IP over Ethernet transport
option (NPGE) is used and when the
IPoA option is used with an NPS1 based
network interface unit. The parameter is
not used with the GTPU/NIS HW based
Iu-PS interface.
The IPBasedRouteId refers to the logical
IP Based Route entity configured in the
IP layer with MML/SCLI or via the IP Plan
interface. The IP Based Route configured
for the Iu-PS interface is used for the user
plane connections towards the Iu-PS CN
element controlling the interface unit and
port selection along with the source IP
address and UDP port selection.
Note: The IUPSIP parameters are
configured with IP over Ethernet transport option. In addition the IUPSIP configuration is needed with IPA-RNC:NPS1
based network interface unit (IPoA). The
IUPSIP parameters are not used with the
IPA-RNC:GTPU/NIS HW based Iu-PS
interface (IPoA).
Default value
0
Default value notes
Value not defined.
Special value
0
Related features
312
IP based Iu-PS (optional) OR Basic
functions (standard)
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.18.3
Field
Description
DN00211177
Issue 12B
Summary of changes
IPNetmaskPS (IP netmask for the IUPS destination subnet)
RNC RN6.0 2.0
RNC RN7.0
The IPNetmaskPS with the DestIPAddressPS attribute forms a destination IP
subnet definition for the Iu-PS user plane
connections (GTP tunnels). The RNC
performs the IP Based Route id reference
selection for the new Iu-PS connection in
between the destination IP subnet and
the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUPSIP
object instance needed under the IUPS
object instance. Example IPv4: 0.0.0.0 /
0.0.0.0 -> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUPSIP objects under the IUPS.
Example IPv4: IUPSIP#1 192.168.0.0 /
255.255.255.240 -> IP Based Route id y,
IUPSIP#2 192.168.0.16 /
255.255.255.240 -> IP Based Route id z.
Note: This parameter is configured
in the following cases:
- IP over Ethernet transport option
with cRNC NPGE, mcRNC and I-HSPA
- IP over ATM option with an
cRNC/NPS1 based network interface
- Always used with I-HSPA Iu-PS
configuration
As an exception the parameter is not
used with cRNC GTPU/NIS HW based
Iu-PS interface.
The IPNetmaskPS with the DestIPAddressPS attribute forms a destination IP
subnet definition for the Iu-PS user plane
connections (GTP tunnels). The RNC
performs the IP Based Route id reference
selection for the new Iu-PS connection in
between the destination IP subnet and
the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signaled by
the CN and there is only one IUPSIP
object instance needed under the IUPS
object instance. Example IPv4: 0.0.0.0 /
0.0.0.0 -> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUPSIP objects under the IUPS.
Example IPv4: IUPSIP#1 192.168.0.0 /
255.255.255.240 -> IP Based Route id y,
IUPSIP#2 192.168.0.16 /
255.255.255.240 -> IP Based Route id z.
Note: This parameter is configured
in the following cases:
- IP over Ethernet transport option
with cRNC NPGE, mcRNC and Flexi
Direct RNC
- IP over ATM option with an
cRNC/NPS1 based network interface
- Always used with Flexi Direct RNC
Iu-PS configuration
As an exception the parameter is not
used with cRNC GTPU/NIS HW based
Iu-PS interface.
Id:0900d805809da32a
313
Summary of changes
WCDMA Radio Network Configuration Parameters
Field
RNC RN6.0 2.0
Default value notes
Related features
1.2.18.4
RNC RN7.0
Referred IP Based Route gets selected
regardless of the IP address signaled by
the CN.
IP based Iu-PS (optional)
IP based Iu-PS (optional) OR Basic
functions (standard)
IPQMIdPS (IPQM object id for IuPS)
Field
RNC RN6.0 2.0
RNC RN7.0
Full Name
IPQM object id for IuItemPS
IPQM object id for IuPS
Description
The IPQM identification gives the reference to the IPQM object used for the PS
CN. The IPQM object defines the UMTS
traffic class to DSCP mapping to be used
for the IP connections at the Iu interface.
Note: This parameter is configured
when the IP over Ethernet transport
option (NPGE) is used and when the
IPoA option is used with an NPS1 based
network interface unit. The parameter is
not used with the GTPU/NIS HW based
Iu-PS interface.
The IPQM identification gives the reference to the IPQM object used for the PS
CN. The IPQM object defines the UMTS
traffic class to DSCP mapping to be used
for the IP connections at the Iu interface.
The referred IPQM instance has to exist
in the system before IUPSIP is created.
Note for IPA-RNC: This parameter is
configured when the IP over Ethernet
transport option (NPGE) is used and
when the IPoA option is used with an
NPS1 based network interface unit. The
parameter is not used with the GTPU/NIS
HW based Iu-PS
Range and step
0..8, step 1
1..8, step 1
Default value
0
Default value notes
0 means that the IPQM reference is not
given and the default values are used.
Related parameters
IPQMId of IPQM - The IPQM object
instance referred by IPQMIdPS has to
exist.
Related features
IP based Iu-PS (optional) OR Basic
functions (standard)
1.2.18.5
Field
IUPSIPId (IUPSIP Identifier )
RNC RN6.0 2.0
Related features
314
RNC RN7.0
IP based Iu-PS (optional) OR Basic
functions (standard)
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.19
1.2.19.1
Field
IUR
HSDPACCEnabledIur (HSDPA Congestion Control activation Iur)
RNC RN6.0 2.0
Related parameters
1.2.19.2
Field
Related parameters
Summary of changes
RNC RN7.0
HSPAOverIur of IUR - HSDPACCEnabledIur should not be set as Enabled if
HSPAOverIur is Disabled.
HSPAOverIur (HSPA over Iur)
RNC RN6.0 2.0
RNC RN7.0
NRncVersion of IUR - The system checks
if the release version of Neighboring RNC
is Rel'6 or later before the activation of
the HSPA over Iur feature.
IurUPSupport of IUR - IUR-HSPAOverIur
cannot be supported, if IurUPSupport is
not supported.
HSDPADynamicResourceAllocation of
RNFC - The system checks if the HSDPA
Dynamic Resource Allocation feature is
activated before the activation of the
HSPA over Iur feature.
HSDPAMobility of RNFC - The system
checks if the HSDPA Serving Cell
Change feature is activated before the
activation of the HSPA over Iur feature.
NRncVersion of IUR - The system checks
if the release version of Neighboring RNC
is Rel'6 or later before the activation of
the HSPA over Iur feature.
HSDPACCEnabledIur of IUR HSPAOverIur should not be set as
Disabled if HSDPACCEnabledIur is
Enabled.
HSDPADynamicResourceAllocation of
RNFC - The system checks if the HSDPA
Dynamic Resource Allocation feature is
activated before the activation of the
HSPA over Iur feature.
HSDPAMobility of RNFC - The system
checks if the HSDPA Serving Cell
Change feature is activated before the
activation of the HSPA over Iur feature.
AppAwareRANEnabled of IUR - The
system shall prevent the modification of
HSPAOverIur parameter value from '1' to
'0' if AppAwareRANEnabled parameter is
set to Enabled.
DN00211177
Issue 12B
Id:0900d805809da32a
315
Summary of changes
1.2.19.3
Field
Related parameters
WCDMA Radio Network Configuration Parameters
IBTSSharing (IBTS Sharing)
RNC RN6.0 2.0
RNC RN7.0
IurUPSupport of IUR - This parameter
indicates user plane procedure support of
the Iur connection. IBTSSharing parameter can be set to "1" only if the IurUPSupport is "1" for the neighbouring I-HSPA
Adapter.
NRncRelocationSupport of IUR - This
parameter identifies whether a neighbouring RNC supports the relocation of
SRNC or not. IBTSSharing parameter
can be set to '1' only if the neighbouring
Flexi Direct RNC supports relocation of
SRNC.
NRncRelocationSupport of IUR - This
parameter identifies whether a neighbouring RNC supports the relocation of
SRNC or not. IBTSSharing parameter
can be set to '1' only if the neighbouring IHSPA Adapter supports relocation of
SRNC.
NeighbouringRNWElement of IUR NeighbouringRNWElement indicates if
the neighbouring RNC is an 3G WCDMA
RNC or an I-HSPA Adapter. The
IBTSSharing parameter can be set to "1"
only if the neighbouring RNW element is
an I-HSPA Adapter.
1.2.19.4
Field
Range and step
1.2.19.5
Field
Modification
1.2.19.6
Field
NeighbouringRNWElement of IUR NeighbouringRNWElement indicates if
the neighbouring RNC is an 3G WCDMA
RNC or an Flexi Direct RNC. The
IBTSSharing parameter can be set to "1"
only if the neighbouring RNW element is
an Flexi Direct RNC.
MaxIurNRTHSDSCHBitRate (Maximum NRT HS-DSCH MAC-d flow
bit rate over Iur)
RNC RN6.0 2.0
0..9600, step 128
RNC RN7.0
128..9600, step 128
NeighbouringPLMNid/MCC (Mobile Country Code)
RNC RN6.0 2.0
unmodifiable
RNC RN7.0
onLine
NeighbouringPLMNid/MNC (Mobile Network Code)
RNC RN6.0 2.0
RNC RN7.0
Description
Unique network identification within
country. MNC consists of two or three
digits. MNC together with MCC identifies
the PLMN uniquely (globally).
Unique network identification within
country. MNC consists of two or three
digits. MNC together with MCC identifies
the PLMN uniquely (globally).
If you modify the MNC, you might
have to also adjust the MNC length.
Modification
unmodifiable
onLine
316
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Related parameters
1.2.19.7
Field
Summary of changes
RNC RN6.0 2.0
MNCLength of IUR -
RNC RN7.0
MNCLength of IUR - This parameter shall
be defined with 2 digit or 3 digit based on
MNCLength.
NeighbouringPLMNid/MNCLength (Mobile Network Code Length)
RNC RN6.0 2.0
RNC RN7.0
Modification
unmodifiable
onLine
Related parameters
MNC of IUR -
MNC of IUR - This parameter defines
whether 2 or 3 digits are used in the
Mobile Network Code.
1.2.19.8
Field
Description
Related parameters
NRncId (Neighbour RNC identifier)
RNC RN6.0 2.0
RNC RN7.0
This parameter identifies the neighbor
RNC. A unique identification for an RNC
node within the UTRAN.
For RAN 2054 feature "Extension of
RNC ids" only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
This parameter identifies the neighbor
RNC. A unique identification for an RNC
node within the UTRAN.
For RAN 2054 feature "Extension of
RNC ids" only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
NRncVersion of IUR - NRNCID can be
set greater than 4095, if NRncVersion is
Rel7 or higher.
NeighbouringRNWElement of IUR NRNCID can be set greater than 4095
only, if NeighbouringRNWElement is
Flexi Direct RNC.
DN00211177
Issue 12B
Id:0900d805809da32a
317
Summary of changes
1.2.19.9
Field
Related parameters
WCDMA Radio Network Configuration Parameters
NRncNetworkInd (Network indicator of neighbour RNC)
RNC RN6.0 2.0
NetworkInd of IUPS -
RNC RN7.0
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
1.2.19.10
OverbookingSwitchIur (Overbooking Switch Iur)
Field
RNC RN6.0 2.0
RNC RN7.0
Range and step
0 (DISABLED), 1 (ENABLED)
0 (Disabled), 1 (Enabled)
1.2.19.11
Field
NRncVersion (Release version of Neighbouring RNC)
RNC RN6.0 2.0
Related parameters
RNC RN7.0
NRncId of IUR - NRNCID can be set
greater than 4095, if NRncVersion is Rel7
or higher.
NeighbouringRNWElement of IUR NRncVersion must be greater than or
equal to Rel6, if NeighbouringRNWElement is Flexi Direct RNC.
318
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.19.12
Field
Related parameters
1.2.19.13
Field
Summary of changes
NRncRelocationSupport (Serving RNC Relocation Support of neighbour RNC)
RNC RN6.0 2.0
RNC RN7.0
RelocationSupport of IUCS -
NRncSignPointCode (Signalling point code of neighbour RNC)
RNC RN6.0 2.0
RNC RN7.0
Description
The code that uniquely identifies the sig- The code identifies the signalling point in
nalling point in the signalling network.
the signalling network.
Combination of NRncNetworkInd and
NRncSignPointCode uniquely identifies a
Signalling Point.
Related parameters
NRncNetworkInd of IUR SignPointCode of IUPS -
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
1.2.19.14
Field
NeighbouringRNWElement (Type of the Neighbouring RNW
Element)
RNC RN6.0 2.0
RNC RN7.0
Description
This parameter indicates whether the
neighboring WCDMA Controller Node is
a 3G RNC or an I-HSPA Adapter.
This parameter indicates whether the
neighboring WCDMA Controller Node is
a 3G RNC or a Flexi Direct RNC.
Range and step
0 (3G-WCDMA RNC), 1 (I-HSPA
Adapter)
0 (3G-WCDMA RNC), 1 (Flexi Direct
RNC)
DN00211177
Issue 12B
Id:0900d805809da32a
319
Summary of changes
WCDMA Radio Network Configuration Parameters
Field
RNC RN6.0 2.0
Related parameters
RNC RN7.0
NRncId of IUR - NRNCID can be set
greater than 4095 only, if NeighbouringRNWElement is Flexi Direct RNC.
NRncVersion of IUR - NRncVersion must
be greater than or equal to Rel6, if NeighbouringRNWElement is Flexi Direct
RNC.
1.2.19.15
IurUPSupport (User Plane support of Iur connection)
Field
RNC RN6.0 2.0
Related parameters
1.2.20
1.2.20.1
HSPAOverIur of IUR - IurUPSupport
cannot be set to “Not supported” if IURHSPAOverIur is enabled.
PFL
AMRToNonPreferredLayer (AMR to Non Preferred Layer)
Field
Range and step
1.2.20.2
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
1.2.21
1.2.21.1
RNC RN7.0
0 (Disabled), 1 (Enabled)
LaySelLowLoadPref (Layer Selection Low Load Preferred)
Field
Range and step
RNC RN7.0
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
RNC RN7.0
0 (Disabled), 1 (Enabled)
PREBTS
TechnologyInformation (Technology Information)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
This parameter specifies the BTS type
until it has been commissioned. The
Technology Information is reported to the
RNC Mediator from the BTS with the BTS
O&M interface.
This parameter specifies the BTS type
until it has been commissioned. RNC
informs the Technology Information to
the BTS via BTS O&M interface.
Range and step
3 (FlexiBTS)
3 (FlexiBTS), 17 (FlexiLiteBTS)
320
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.22
1.2.22.1
RNAC
DLmaxBitRatePerSF/DLmaxBitRateSF128 (Maximum DL bit rate
with spreading factor 128)
Field
Related parameters
1.2.22.2
RNC RN6.0 2.0
RNC RN7.0
DLmaxBitRateSF256 of RNAC - Value of
the parameter shall be bigger than the
value of the parameter
DLmaxBitRateSF256.
DLmaxBitRateSF256 of RNAC - Value of
the parameter must be bigger than the
value of the parameter
DLmaxBitRateSF256.
DLmaxBitRateSF64 of RNAC - Value of
the parameter shall be smaller than the
value of the parameter
DLmaxBitRateSF64.
DLmaxBitRateSF64 of RNAC - Value of
the parameter must be smaller than the
value of the parameter
DLmaxBitRateSF64.
DLpuncturingLimit of RNAC -
DLpuncturingLimit of RNAC -
PCrangeDL (Radio link downlink power control range)
Field
Default value
1.2.22.3
Field
Description
DN00211177
Issue 12B
Summary of changes
RNC RN6.0 2.0
15
RNC RN7.0
20
SRBDelay (SRB delay)
RNC RN6.0 2.0
RNC RN7.0
The parameter defines the number of
frames after the PC preamble period
during which the transmission of data on
the RRC Signalling Radio Beares should
be suspended by the UE. The SRB delay
can be applied to the physical layer synchronization procedure A when the first
radio link set is established for the UE.
The parameter defines the number of
frames after the PC preamble period
during which the transmission of data on
the RRC Signalling Radio Bearers should
be suspended by the UE. The SRB delay
can be applied to the physical layer synchronization procedure A when the first
radio link set is established for the UE.
Id:0900d805809da32a
321
Summary of changes
1.2.22.4
Field
Description
1.2.22.5
Field
Range and step
322
WCDMA Radio Network Configuration Parameters
UlScrCodeMin (Uplink scrambling code minimum value)
RNC RN6.0 2.0
RNC RN7.0
This parameter defines the minimum
value of the uplink scrambling code.
From RN4.0 Inc 1 onwards, this
parameter is used for defining the start of
the scrambling code value and the range
of the uplink scrambling codes that are
possible to allocate in the RNC. The
range of the uplink scrambling codes allocated by RNC starts from the value of the
UlScrCodeMin parameter and the last
value of the uplink scrambling code is
UlScrCodeMin + the number of ICSU
units * the maximum number of users per
ICSU.
Actually the last indexed value
depends on the value of the UlScrCodeMin. For example, if the value is set to
16777215, it continues allocation from
the value 8192. If the maximum number
of ICSU units is 4 and the maximum
number of users in RNC is 8192, then
RNC allocates the value 16777215 and
values from 8192 to 40959.
The uplink scrambling code is unique
for each MS and it is used continuously,
even if the frequency is changed. The
first 0...8191 scrambling codes are
reserved to be used in inter-RAT handovers from GSM to UTRAN.
All uplink physical channels are subjected to scrambling with a complexvalued scrambling code. The UL DPCH
will be scrambled with a long scrambling
code.
This parameter defines the minimum
value of the uplink scrambling code.
From RN4.0 Inc 1 onwards, this
parameter is used for defining the start of
the scrambling code value and the range
of the uplink scrambling codes that are
possible to allocate in the RNC. The
range of the uplink scrambling codes allocated by RNC starts from the value of the
UlScrCodeMin parameter and the last
value of the uplink scrambling code is
UlScrCodeMin + the number of ICSU
units * the maximum number of users per
ICSU.
Actually the last indexed value
depends on the value of the UlScrCodeMin. For example, if the value is set to
16777215, it continues allocation from
the value 8192. If the maximum number
of ICSU units is 4 and the maximum
number of users in RNC is 8192, then
RNC allocates the value 16777215 and
values from 8192 to 40959.
The uplink scrambling code is unique
for each MS and it is used continuously,
even if the frequency is changed. The
first 0...8191 scrambling codes are
reserved to be used in inter-RAT handovers from GSM to UTRAN.
All uplink physical channels are subjected to scrambling with a complexvalued scrambling code. The UL DPCH
will be scrambled with a long scrambling
code.
Note: If this parameter is modified,
RNC need to be restarted immediately so
that the RNC takes the new value into
use.
LoadBasedAMRCodecMode (Usage of Load based AMR codec
mode selection)
RNC RN6.0 2.0
0 (disabled), 1 (enabled)
Id:0900d805809da32a
RNC RN7.0
0 (Disabled), 1 (Enabled)
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.23
1.2.23.1
Field
Summary of changes
RNC
CommonMCC (Common MCC)
RNC RN6.0 2.0
RNC RN7.0
Description
MCC (Mobile Country Code) part of
Common PLMN Id. Common PLMN Id is
used to represent all the operators in the
multi-operator core network. MCC
consists of three digits. MCC together
with MNC identifies the Common PLMN
id.
Common PLMN id (CommonMCC
and CommonMNC) should not be the
same as any PLMNid in RNC-IuOperator
CommonMCC is modifiable only
when there is no WCEL whose WCELPLMNid is exact same with CommonMCC/CommonMNC
If Common PLMN id is defined,
WCELCSCNId and WCELPSCNId
should not be configured
MCC (Mobile Country Code) part of
Common PLMN Id. Common PLMN Id is
used to represent all the operators in the
multi-operator core network. MCC
consists of three digits. MCC together
with MNC identifies the Common PLMN
id.
Common PLMN id must not be the
same as any primary or shared area
PLMNid in IUO instances.
Related parameters
WCELCSCNId of WCEL - If Common
PLMN id is defined, WCELCSCNId and
WCELPSCNId should not be configured
WCELMCC of WCEL - This parameter is
modifiable only when there is no WCEL
whose PLMNid is exactly the same as
CommonMCC/CommonMNC.
WCELPLMNid of WCEL - This parameter
is modifiable only when there is no WCEL
whose WCELPLMNid is exactly the same
as CommonMCC/CommonMNC
WCELPSCNId of WCEL - If Common
PLMN id is defined, WCELCSCNId and
WCELPSCNId should not be configured
CommonMNC of RNC - MNC of
Common PLMN Id.
DN00211177
Issue 12B
WCELMNC of WCEL - This parameter is
modifiable only when there is no WCEL
whose PLMNid is exactly the same as
CommonMCC/CommonMNC.
WCELMNCLength of WCEL - This
parameter is modifiable only when there
is no WCEL whose PLMNid is exactly the
same as CommonMCC/CommonMNC.
Id:0900d805809da32a
323
Summary of changes
1.2.23.2
Field
WCDMA Radio Network Configuration Parameters
CommonMNC (Common MNC)
RNC RN6.0 2.0
RNC RN7.0
Description
This parameter defines MNC (Mobile
Network Code) part of Common PLMN
Id. Common PLMN Id is used to represent all the operators in the multioperator core network. MNC consists of
two or three digits. MNC together with
MCC identifies the Common PLMN Id.
Common PLMN Id (CommonMCC
and CommonMNC) cannot be the same
as any PLMNId in RNC-IuOperator.
CommonMNC is modifiable only
when there is no WCEL whose WCELPLMNId is exactly the same as CommonMCC/CommonMNC.
This parameter defines MNC (Mobile
Network Code) part of Common PLMN
Id. Common PLMN Id is used to represent all the operators in the multioperator core network. MNC consists of
two or three digits. MNC together with
MCC identifies the Common PLMN Id.
Common PLMN id must not be the
same as any primary or shared area
PLMNid in IUO instances.
Related parameters
WCELCSCNId of WCEL - If Common
PLMN Id is defined, WCELCSCNId and
WCELPSCNId cannot be configured.
WCELMCC of WCEL - This parameter is
modifiable only when there is no WCEL
whose PLMNid is exactly the same as
CommonMCC/CommonMNC.
WCELPLMNid of WCEL - This parameter
is modifiable only when there is no WCEL
whose WCELPLMNId is exactly the
same as CommonMCC/CommonMNC.
WCELPSCNId of WCEL - If Common
PLMN Id is defined, WCELCSCNId and
WCELPSCNId cannot be configured.
CommonMCC of RNC - MCC of
Common PLMN Id.
WCELMNC of WCEL - This parameter is
modifiable only when there is no WCEL
whose PLMNid is exactly the same as
CommonMCC/CommonMNC.
WCELMNCLength of WCEL - This
parameter is modifiable only when there
is no WCEL whose PLMNid is exactly the
same as CommonMCC/CommonMNC.
CommonMNCLength of RNC - MNC
length of Common PLMN Id. Value range
depends on the MNCLength: 00...99 (if
MNCLength is 2) or 000...999 (if MNCLength is 3). If the related parameter
CommonMNCLenth has a default value
of "not defined", then the only allowed
value for the CommonMNC is the default
value "not defined".
324
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.23.3
Summary of changes
ExtendedULDLactivationTmr (Extended Cell_FACH inactivity
supervision timer)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
This parameter defines an extended
Cell_FACH state inactivity supervision
time used by the RNC instead of the
normal UL_DL_Activation_Timer. If set to
a value greater than zero, this value is
used for all UEs not supporting the
Cell/URA_PCH state.
This parameter defines an extended
Cell_FACH state inactivity supervision
time used by the RNC instead of the
normal UL_DL_Activation_Timer. If set to
a value greater than zero, this value is
used for all UEs not supporting the
Cell/URA_PCH state. Otherwise, normal
WAC-UL_DL_Activation_Timer is used
for all UEs not supporting
Cell/URA_PCH.
Related parameters
UL_DL_activation_timer of RNC - If
ExtendedULDLactivationTmr = 0, normal
UL_DL_Activation_Timer is used for all
UEs and no extended time for UEs not
supporting Cell/URA_PCH is used.
1.2.23.4
LCSfunctionality (LCS functionality)
Field
RNC RN6.0 2.0
Related parameters
1.2.23.5
RNC RN7.0
LCSSupportForAnchoring of RNC - LCS
Support in Drift RNC feature can be
enabled only if LCS functionality is
enabled.
ConnectionRetryCounter (OAM Connection Establishment Retry
Counter)
Field
RNC RN6.0 2.0
RNC RN7.0
Range and step
1..20, step 1
1..30, step 1
Default value
10
15
DN00211177
Issue 12B
Id:0900d805809da32a
325
Summary of changes
1.2.23.6
Field
WCDMA Radio Network Configuration Parameters
SIB11_priority (Priority for SIB11)
RNC RN6.0 2.0
RNC RN7.0
Description
The priority of the System Information
Block 11, which is used by the scheduling
algorithm in the RNC to give precedence
to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 11 priority
shall have higher priority value than SIB
1, SIB2, SIB3, SIB5 and SIB7.
System Information Block type 11bis
(SIB11bis) provides extension segments
for SIB11. The value of the SIB11_priority
is used also for SIB11bis.
The priority of the System Information
Block 11, which is used by the scheduling
algorithm in the RNC to give precedence
to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 11 shall
have lower priority than SIB 1, SIB2,
SIB3, and SIB5. The value of the
SIB11_priority is used also for SIB11bis.
Related parameters
SIB18_priority of RNC - The priority of
SIB11 shall not be lower than what is
defined for SIB18.
SIB18_priority of RNC - The priority of
SIB11 shall not be lower than what is
defined for SIB18.
1.2.23.7
Field
Description
1.2.23.8
Field
Description
326
SIB15_priority (Priority for SIB15)
RNC RN6.0 2.0
RNC RN7.0
The parameter defines the priority of the
System Information Block 15, which is
used by the scheduling algorithm in the
RNC to give precedence to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 15 priority
shall have higher priority value than SIB
1, SIB2, SIB3, SIB5 and SIB7.
The parameter defines the priority of the
System Information Block 15, which is
used by the scheduling algorithm in the
RNC to give precedence to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 15 priority
shall have lower than SIB 1, SIB2, SIB3,
and SIB5.
SIB18_priority (Priority for SIB18)
RNC RN6.0 2.0
RNC RN7.0
The priority of the System Information
Block 18, which is used by the scheduling
algorithm in the RNC to give precedence
to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 18 priority
shall have higher priority value than SIB
1, SIB2, SIB3, SIB5 and SIB7.
The priority of the System Information
Block 18, which is used by the scheduling
algorithm in the RNC to give precedence
to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 18 priority
shall have lower than SIB 1, SIB2, SIB3,
and SIB5.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Related parameters
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
SIB11_priority of RNC - The priority of
SIB18 shall not be higher than what is
defined for SIB11
SIB11_priority of RNC - The priority of
SIB18 shall not be higher than what is
defined for SIB11
SIB12_priority of RNC - The priority of
SIB18 shall not be higher than what is
defined for SIB12
1.2.23.9
SIB19Priority (Priority for SIB19)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
This parameter defines the priority of the
System Information Block 19, which is
used by the scheduling algorithm in the
RNC to give precedence to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 19 priority
shall have higher priority value than SIB
1, SIB2, SIB3, SIB5 and SIB7.
This parameter defines the priority of the
System Information Block 19, which is
used by the scheduling algorithm in the
RNC to give precedence to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 19 priority
shall have lower than SIB 1, SIB2, SIB3,
and SIB5.
Default value
3
4
1.2.23.10
SIB3_priority (Priority for SIB3)
Field
Interfaces
1.2.23.11
RNC RN6.0 2.0
RNC RN7.0
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC<->UE
RAC<->RNC, EM<->RNC, RACApp<>RAC
PageRep1stInterv (Repetition interval of the first repeated connected mode paging procedure)
Field
Default value
DN00211177
Issue 12B
RNC RN6.0 2.0
700
RNC RN7.0
1100
Id:0900d805809da32a
327
Summary of changes
Field
Default value notes
1.2.23.12
Field
Description
328
WCDMA Radio Network Configuration Parameters
RNC RN6.0 2.0
RNC RN7.0
DRX Cycle length 640ms assumed. The
first paging repetition should be executed
as soon as possible to emphasize the
response-time for all those mobiles which
have not received the actual paging
message. This will, however, cause the
first repeated paging executed also for a
certain amount of the mobiles that
actually have received the 1st paging, but
there has not been enough time to send
the paging response to the RNC. In
RAN2 it is assumed that the paging load
is not the limiting factor.
DRX Cycle length 640ms assumed. The
first paging repetition should be executed
as soon as possible to emphasize the
response-time for all those mobiles which
have not received the actual paging
message. This will, however, cause the
first repeated paging executed also for a
certain amount of the mobiles that
actually have received the 1st paging, but
there has not been enough time to send
the paging response to the RNC.
RestrictionInterval (Restriction Interval)
RNC RN6.0 2.0
RNC RN7.0
Length of traffic restriction period in RNC
when 'Radio Network Access Regulation
Function' or 'Domain Specific Access
Class Restriction' is active in RNC. RNC
sets timer using parameter value. During
traffic restriction period user defined
amount of Access Classes are prevented
from accessing the network. When timer
set with this parameter value expires new
set of Access Classes are selected to be
'barred' and timer is set again. The
amount of Access Classes to be barred
simultaneously is defined with parameter
CellAccessRestriction.
Length of traffic restriction period in RNC
when 'Radio Network Access Regulation
Function' or 'Domain Specific Access
Class Restriction' or ‘Automatic Access
Class Restriction’ is active in RNC. RNC
sets timer using parameter value. During
traffic restriction period user defined
amount of Access Classes are prevented
from accessing the network. When timer
set with this parameter value expires new
set of Access Classes are selected to be
'barred' and timer is set again. The
amount of Access Classes to be barred
simultaneously is defined with parameter
CMOB -CellAccessRestriction. In case of
the Automatic Access Restriction, the
number of the restricted access classes
is automatically increased or decreased
according to the overload conditions.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Related parameters
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
ACBarredListSystem of CMOB - When
Access Classes to be barred have been
selected, ACBarredListSystem is
updated to show the barring situation.
ACBarredListSystem of CMOB - When
Access Classes to be barred have been
selected, ACBarredListSystem is
updated to show the barring situation.
CellAccessRestriction of CMOB - 'CellAccessRestriction' indicates how many
Access Classes will be barred (out of
Access Classes 0 to 9).
CellAccessRestriction of CMOB - 'CellAccessRestriction' indicates how many
Access Classes will be barred (out of
Access Classes 0 to 9).
RNARDSACGuardTime of RNAC RNARDSACGuardTime shall be smaller
than RestrictionInterval.
Related features
1.2.23.13
Radio Network Access Regulation
Function (optional)
Radio Network Access Regulation
Function (optional) OR Automatic
access class restriction (optional)
RNCIPAddress (RNC IP-address)
Field
RNC RN6.0 2.0
RNC RN7.0
Description
This parameter specifies the RNC (OMU)
IP address that is needed to establish
certain TCP/IP connections to the RNC
OMU.
This parameter specifies the RNC IP
address that is needed to establish
TCP/IP connections to the RNC OMU.
Modification
onLine
unmodifiable
Interfaces
RNC->NetAct topology, RNC->OMS
topology, RNC->OMS topology UI
RNC->NetAct topology, RNC->OMS
topology, RNC->OMS topology UI, RNC>RAC
DN00211177
Issue 12B
Id:0900d805809da32a
329
Summary of changes
1.2.23.14
Field
Range and step
330
WCDMA Radio Network Configuration Parameters
RncOptions (RNC Options)
RNC RN6.0 2.0
RNC RN7.0
0 (Inter System Handover), 1 (Location
Services - RTT), 2 (IMSI Based Handover), 3 (WCDMA 1900), 4 (Multiple
Core Networks Support), 5 (Multioperator RAN), 6 (Service Area Broadcast), 7 (Emergency Inter System Handover), 8 (HSDPA, ChSw, UL DPCHSch,
ResumpT and DirRRCConSetu), 9
(WCDMA 850), 10 (Enhanced Priority
Based Scheduling and OLC), 12 (UE
based A-GPS), 13 (Network based AGPS), 14 (Intelligent Emergency Inter
System Handover), 15 (Connectivity
Support for 512 BTSs), 16 (Load and
Service Based Handover), 17 (Power
Balancing), 18 (Support for Tandem/Transcoder Free Operation), 19
(AMR Codec Sets [12.2,7.95,5.90,4.75]
& [5.90,4.75]), 20 (Wideband AMR
Codec Set [12.65, 8.85, 6.6]), 21
(Throughput Based Optimisation of PS
Algorithm), 22 (Flexible Upgrade of NRT
DCH Data Rate), 23 (Route Selection),
24 (WCDMA 1.7/2.1GHz), 25 (WCDMA
1.7 and 1.8GHz), 26 (Radio Network
Access Regulation), 27 (HSDPA Mob,
SHO, SCC and Soft/softer HO for
DPCH), 29 (HSDPA with AMR ), 30
(WCDMA 900), 31 (Extended Cell
(60km)), 32 (Flexible Connection of
VPCs for WBTS), 33 (Wireless Priority
Service), 34 (Full WCDMA 1900
UARFCN range), 35 (Transport Bearer
Tuning), 36 (Path Selection), 37 (HSDPA
Dynamic Resource Allocation), 38
(HSDPA 10 Codes), 39 (HSDPA 15
Codes), 40 (HSDPA layering for UEs in
common channels), 41 (HSDPA Code
multiplexing), 42 (16 kbps Return Ch
DCH Data Rate Support for HSDPA), 43
(HSDPA 48 users per cell), 44 (Flexible
IU), 45 (Dynamic Scheduling for HSDPA
with Path Selection),
0 (Inter System Handover), 1 (Location
Services - RTT), 2 (IMSI Based Handover), 3 (WCDMA 1900), 4 (Multiple
Core Networks Support), 5 (Multioperator RAN), 6 (Service Area Broadcast), 7 (Emergency Inter System Handover), 8 (HSDPA, ChSw, UL DPCHSch,
ResumpT and DirRRCConSetu), 9
(WCDMA 850), 10 (Enhanced Priority
Based Scheduling and OLC), 12 (UE
based A-GPS), 13 (Network based AGPS), 14 (Intelligent Emergency Inter
System Handover), 15 (Connectivity
Support for 512 BTSs), 16 (Load and
Service Based Handover), 17 (Power
Balancing), 18 (Support for Tandem/Transcoder Free Operation), 19
(AMR Codec Sets [12.2,7.95,5.90,4.75]
& [5.90,4.75]), 20 (Wideband AMR
Codec Set [12.65, 8.85, 6.6]), 21
(Throughput Based Optimisation of PS
Algorithm), 22 (Flexible Upgrade of NRT
DCH Data Rate), 23 (Route Selection),
24 (WCDMA 1.7/2.1GHz), 25 (WCDMA
1.7 and 1.8GHz), 26 (Radio Network
Access Regulation), 27 (HSDPA Mob,
SHO, SCC and Soft/softer HO for
DPCH), 29 (HSDPA with AMR ), 30
(WCDMA 900), 31 (Extended Cell
(60km)), 32 (Flexible Connection of
VPCs for WBTS), 33 (Wireless Priority
Service), 34 (Full WCDMA 1900
UARFCN range), 35 (Transport Bearer
Tuning), 36 (Path Selection), 37 (HSDPA
Dynamic Resource Allocation), 38
(HSDPA 10 Codes), 39 (HSDPA 15
Codes), 40 (HSDPA layering for UEs in
common channels), 41 (HSDPA Code
multiplexing), 42 (16 kbps Return Ch
DCH Data Rate Support for HSDPA), 43
(HSDPA 48 users per cell), 44 (Flexible
IU), 45 (Dynamic Scheduling for HSDPA
with Path Selection),
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
DN00211177
Issue 12B
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
46 (Dynamic Scheduling for NRT DCH
with Path Selection), 47 (Emergency Call
Redirect to GSM), 48 (HSUPA with simultaneous AMR voice call), 49 (HSUPA
Basic 3 users per BTS), 50 (HSUPA
Basic 12 users per BTS), 51 (HSUPA
Basic 24 users per BTS), 52 (RNC GUI
for BTS Connection Resources), 53
(Connectivity Support for 600 BTSs), 54
(RNC Iu Link Break Protection), 55
(HSDPA 10 Mbps per User), 56 (HSPA
Inter RNC Cell Change), 57 (HSUPA 2.0
Mbps), 58 (Extended Cell (35 km)), 59
(Extended Cell (180km)), 60 (Capacity
license for the number of carriers), 61 (IP
based IU-CS), 62 (IP based IU-PS), 63
(HSDPA Congestion Control), 64 (IP
based Iur), 65 (SAS Centric Iupc), 66
(Automated Definition of Neighbouring
Cell), 67 (Detected Set Reporting and
Measurements), 68 (Detected Set
Reporting Based SHO), 69 (NodeB RAB
Reconfig Support), 70 (QoS Aware
HSPA Scheduling), 71 (Streaming QoS
for HSPA), 72 (HSUPA Basic 60 users
per BTS), 73 (NRT Multi-RABs on
HSPA), 74 (HSDPA 14 Mbps per User),
75 (IP Based Iub), 76 (Dual Iub), 77
(HSDPA inter-frequency handover), 78
(Directed Retry of AMR call), 79 (HSDPA
64 Users per Cell), 80 (LCS Support in
Drift RNC), 81 (Iub Transport QOS), 82
(Secure BTS Management Interface), 83
(UTRAN-GAN Interworking), 84 (LCS
periodical reporting), 85 (LCS Shape
Conversion), 86 (Satellite Iub), 87 (Interfrequency Handover over Iur), 88 (I-BTS
Sharing), 89 (Multi-Operator Core Network), 90 (CS Voice Over HSPA), 91
(Power Saving Mode for BTS), 92 (Fractional DPCH), 93 (HSUPA 5.8 Mbps), 94
(HSUPA 2ms TTI), 95 (HSDPA 64QAM),
96 (Continuous Packet Connectivity), 97
(Broadcast of A-GPS Assistance Data),
98 (HSPA Transport Fallback), 99 (Position Information in Subscriber Trace
Report), 100 (24 kbps Paging Channel),
101 (HSPA 72 Users Per Cell),
46 (Dynamic Scheduling for NRT DCH
with Path Selection), 47 (Emergency Call
Redirect to GSM), 48 (HSUPA with simultaneous AMR voice call), 49 (HSUPA
Basic 3 users per BTS), 50 (HSUPA
Basic 12 users per BTS), 51 (HSUPA
Basic 24 users per BTS), 52 (RNC GUI
for BTS Connection Resources), 53
(Connectivity Support for 600 BTSs), 54
(RNC Iu Link Break Protection), 55
(HSDPA 10 Mbps per User), 56 (HSPA
Inter RNC Cell Change), 57 (HSUPA 2.0
Mbps), 58 (Extended Cell (35 km)), 59
(Extended Cell (180km)), 60 (Capacity
license for the number of carriers), 61 (IP
based IU-CS), 62 (IP based IU-PS), 63
(HSDPA Congestion Control), 64 (IP
based Iur), 65 (SAS Centric Iupc), 66
(Automated Definition of Neighbouring
Cell), 67 (Detected Set Reporting and
Measurements), 68 (Detected Set
Reporting Based SHO), 69 (NodeB RAB
Reconfig Support), 70 (QoS Aware
HSPA Scheduling), 71 (Streaming QoS
for HSPA), 72 (HSUPA Basic 60 users
per BTS), 73 (NRT Multi-RABs on
HSPA), 74 (HSDPA 14 Mbps per User),
75 (IP Based Iub), 76 (Dual Iub), 77
(HSDPA inter-frequency handover), 78
(Directed Retry of AMR call), 79 (HSDPA
64 Users per Cell), 80 (LCS Support in
Drift RNC), 81 (Iub Transport QOS), 82
(Secure BTS Management Interface), 83
(UTRAN-GAN Interworking), 84 (LCS
periodical reporting), 85 (LCS Shape
Conversion), 86 (Satellite Iub), 87 (Interfrequency Handover over Iur), 88 (I-BTS
Sharing), 89 (Multi-Operator Core Network), 90 (CS Voice Over HSPA), 91
(Power Saving Mode for BTS), 92 (Fractional DPCH), 93 (HSUPA 5.8 Mbps), 94
(HSUPA 2ms TTI), 95 (HSDPA 64QAM),
96 (Continuous Packet Connectivity), 97
(Broadcast of A-GPS Assistance Data),
98 (HSPA Transport Fallback), 99 (Position Information in Subscriber Trace
Report), 100 (24 kbps Paging Channel),
101 (HSPA 72 Users Per Cell),
Id:0900d805809da32a
331
Summary of changes
Field
332
WCDMA Radio Network Configuration Parameters
RNC RN6.0 2.0
RNC RN7.0
102 (BTS Auto Connection), 103
(Common Channel Setup), 104 (MIMO),
105 (Reserved), 106 (Dual-Cell HSDPA
42Mbps), 107 (LTE Interworking-Cell
Reselection to LTE), 108 (LTE Interworking-ISHO from LTE), 109 (HSUPA
16QAM), 110 (HSPA 128 users), 111
(Multi-Band Load Balancing), 112 (HSFACH), 113 (Reserved), 114 (Bandwidth
utilization classes counters for IP), 116
(BW utilization classes counters for VC
and bundle), 117 (Reserved), 118
(Reserved), 119 (Reserved), 120
(RNC2600 Capacity Increase for Smartphones), 121 (Inter Circle Roaming), 122
(PCAP for CellID Measurement Method),
123 (Enhanced Virtual Antenna Mapping), 124 (Reserved), 125 (Reserved),
126 (Reserved), 127 (Reserved), 128
(Reserved), 129 (Reserved)
102 (BTS Auto Connection), 103
(Common Channel Setup), 104 (MIMO),
106 (Dual-Cell HSDPA 42Mbps), 107
(LTE Interworking-Cell Reselection to
LTE), 108 (LTE Interworking-ISHO from
LTE), 109 (HSUPA 16QAM), 110 (HSPA
128 users), 111 (Multi-Band Load Balancing), 112 (HS-FACH), 114 (Bandwidth utilization classes counters for IP),
116 (BW utilization classes counters for
VC and bundle), 120 (RNC2600 Capacity
Increase for Smartphones), 121 (Inter
Circle Roaming), 122 (PCAP for CellID
Measurement Method), 123 (Enhanced
Virtual Antenna Mapping), 124 (Fast
Dormancy Profiling), 125 (HSPA conversational QoS), 126 (Smart LTE Layering),
127 (Layering in RRC Connection
Release), 128 (Application Aware RAN),
129 (Dual Band HSDPA 42 Mbps), 130
(Fast Cell_PCH Switching), 131 (3GPP
Rel8 CBS ETWS support), 132 (Fast
HSPA Mobility), 133 (AMR with DCH
(0,0) Support for Iur), 134 (Optimised
push to talk experience), 135 (UE
Periodic Measurement Report), 136
(Automatic Access Class Restriction),
138 (SAB Support with 2 SCCPCHs),
139 (Femto Handover Control), 140 (Terminal Battery Drain Prevention in Cell
Broadcas), 141 (Mass Event Handler),
142 (Voice Call Priorization during High
Traffic Load), 143 (High Speed Cell
FACH Uplink), 144 (CPC for 128 HSPA
Users)
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.23.15
Field
Related parameters
1.2.23.16
Field
Description
DN00211177
Issue 12B
Summary of changes
ServingOMS (Serving OMS )
RNC RN6.0 2.0
RNC RN7.0
OMSIpAddress of RNC - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS. When
ServingOMS parameter is set to 1 (primary), then OMSIpAddress value 0.0.0.0
is not allowed.
OMSIpAddress of RNC - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS. When
ServingOMS parameter is set to 1 (primary), then OMSIpAddress value 0.0.0.0
is not allowed.
SecOMSIpAddress of RNC - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC. When ServingOMS parameter is set to 2 (secondary),
then SecOMSIpAddress default value
(0.0.0.0) is not allowed.
SecOMSIpAddress of RNC - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC. When ServingOMS parameter is set to 2 (secondary),
then SecOMSIpAddress default value
(0.0.0.0) is not allowed.
ServingOMSSwoRequest of RNC Serving OMS Switchover Request is
used to trigger the OMS switchover procedure in RNC/ADA.
ServingOMSSwoRequest of RNC Serving OMS Switchover Request is
used to trigger the OMS switchover procedure in RNC.
ServingOMSAdminSetting of RNC Serving OMS Admin Setting specifies if
the automatic OMS switchover is in use
or if RNC/ADA is forced to connect to the
specific IP address.
ServingOMSAdminSetting of RNC Serving OMS Admin Setting specifies if
the automatic OMS switchover is in use
or if RNC is forced to connect to the
specific IP address.
ServingOMSAdminSetting (Serving OMS Admin Setting)
RNC RN6.0 2.0
RNC RN7.0
This parameter specifies if the automatic
OMS switchover is in use or if RNC/ADA
is forced to connect to the specific IP
address.
This parameter specifies if the automatic
OMS switchover is in use or if RNC is
forced to connect to the specific IP
address.
Id:0900d805809da32a
333
Summary of changes
Field
Related parameters
1.2.23.17
Field
Description
334
WCDMA Radio Network Configuration Parameters
RNC RN6.0 2.0
RNC RN7.0
OMSIpAddress of RNC - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS. The
Serving OMS Admin Setting parameter
can force the NE to use the primary OMS
IP Address for the active O&M connection.
OMSIpAddress of RNC - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS. The
Serving OMS Admin Setting parameter
can force the NE to use the primary OMS
IP Address for the active O&M connection.
SecOMSIpAddress of RNC - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC. When ServingOMSAdminSetting parameter is set to 2
(secondary forced), then SecOMSIpAddress parameter should not contain
default value (0.0.0.0).
SecOMSIpAddress of RNC - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC. When ServingOMSAdminSetting parameter is set to 2
(secondary forced), then SecOMSIpAddress parameter should not contain
default value (0.0.0.0).
ServingOMSSwoRequest of RNC Serving OMS Switchover Request
parameter is used to trigger the OMS switchover procedure in RNC/ADA. Serving
OMS Admin Setting should have value
"automatic" to enable the operator controlled OMS switchover. The switchover
can be started with parameter Serving
OMS Switchover Request.
ServingOMSSwoRequest of RNC Serving OMS Switchover Request
parameter is used to trigger the OMS switchover procedure in RNC. Serving OMS
Admin Setting should have value "automatic" to enable the operator controlled
OMS switchover. The switchover can be
started with parameter Serving OMS Switchover Request.
ServingOMSSwoRequest (Serving OMS Switchover Request)
RNC RN6.0 2.0
RNC RN7.0
This parameter is a trigger for the OMS
switchover procedure in RNC/ADA.
Note that a successful parameter
change does not yet guarantee successful OMS switchover, which depends on
several other factors. Check that alarm
2081 "OMS SWITCHOVER HAS BEEN
PERFORMED" is visible after switchover
is requested. The alarm indicates that the
OMS switchover is done successfully.
The value of the parameter is not
stored as such in RNC/ADA. It is just
used for triggering the OMS switchover.
Thus the parameter does not have any
value that is used for describing the situation in the network.
This parameter is a trigger for the OMS
switchover procedure in RNC.
Note that a successful parameter
change does not yet guarantee successful OMS switchover, which depends on
several other factors. Check that alarm
0821 "OMS SWITCHOVER HAS BEEN
PERFORMED" is visible after switchover
is requested. The alarm indicates that the
OMS switchover is done successfully.
The value of the parameter is not
stored as such in RNC. It is just used for
triggering the OMS switchover. Thus the
parameter does not have any value that
is used for describing the situation in the
network.
Id:0900d805809da32a
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
Related parameters
Summary of changes
RNC RN6.0 2.0
RNC RN7.0
OMSIpAddress of RNC - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS.
OMSIpAddress of RNC - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS.
SecOMSIpAddress of RNC - Secondary SecOMSIpAddress of RNC - Secondary
OMS IP address specifies the
sec- OMS IP address specifies the
secondary OMS IP address in RNC.
ondary OMS IP address in RNC.
ServingOMSAdminSetting of RNC Serving OMS Admin Setting specifies if
the automatic OMS switchover is in use
or if RNC/ADA is forced to connect to the
specific IP address. The requested OMS
switchover is possible only when Serving
OMS Admin Setting has the value "automatic".
1.2.23.18
ULBLERConfInterval (Uplink measured BLER confidence interval)
Field
Range and step
1.2.24
1.2.24.1
Field
Related parameters
RNC RN6.0 2.0
RNC RN7.0
7 (75%), 10 (85%), 13 (90%), 16 (95%),
20 (97,5%), 23 (99%), 30 (99,9%), 50
(almost 100%)
7 (75%), 10 (85%), 13 (90%), 16 (95%),
20 (97.5%), 23 (99%), 30 (99.9%), 50
(almost 100%)
RNFC
SignConnActivitySupervision (Activity supervision for NAS signaling connection)
RNC RN6.0 2.0
MSActivitySupervision of RNC - When
there is a PS-RAB configured in the MS,
the supervision of inactive Iu-PS connection is managed by using the MSActivitySupervision timer.
RANAPprocInitWait of RNC - See the
parameter description.
CVUserInactInSignConnRel of RNFC This parameter allows usage of the
RANAP cause value 'User Inactivity' in
RANAP:Iu Release Request procedure
when the RNC is releasing an inactive
signaling connection towards the PS-CN.
DN00211177
Issue 12B
ServingOMSAdminSetting of RNC Serving OMS Admin Setting specifies if
the automatic OMS switchover is in use
or if RNC is forced to connect to the
specific IP address. The requested OMS
switchover is possible only when Serving
OMS Admin Setting has the value "automatic".
RNC RN7.0
RANAPprocInitWait of RNC - See the
parameter description.
CVUserInactInSignConnRel of RNFC This parameter allows usage of the
RANAP cause value 'User Inactivity' in
RANAP:Iu Release Request procedure
when the RNC is releasing an inactive
signaling connection towards the PS-CN.
MSActivitySupervision of WAC - When
there is a PS-RAB configured in the MS,
the supervision of inactive Iu-PS connection is managed by using the MSActivitySupervision timer.
Id:0900d805809da32a
335
Summary of changes
1.2.24.2
Field
Range and step
1.2.24.3
Field
Related parameters
WCDMA Radio Network Configuration Parameters
CapaSmartphoneEnabled (Capacity Increase for Smartphones
Enabled)
RNC RN6.0 2.0
0 (disable), 1 (enable)
0 (Disabled), 1 (Enabled)
HSDPA16KBPSReturnChannel (HSDPA 16 kbps UL DCH return
channel on/off switch)
RNC RN6.0 2.0
RNC RN7.0
HSDPAenabled of WCEL - HSDPA must
be enabled in order to apply 16 kbps
return channel in HSDPA capable cell.
HSDPAenabled of WCEL - HSDPA must
be enabled in order to apply 16 kbps
return channel in HSDPA capable cell.
HSDPAinitialBitrateUL of RNHSPA - In
order to apply 16 kbps UL DCH return
channel, user should set initial bit rate
accordingly.
HSDPAinitialBitrateUL of WAC - In order
to apply 16 kbps UL DCH return channel,
user should set initial bit rate accordingly.
HSDPAminAllowedBitrateUL of
RNHSPA - In order to apply 16 kbps UL
DCH return channel, user should set
minimum bit rate accordingly.
336
RNC RN7.0
Id:0900d805809da32a
HSDPAminAllowedBitrateUL of WAC - In
order to apply 16 kbps UL DCH return
channel, user should set minimum bit
rate accordingly.
PTTEnabled of RNFC - The system
prevents deactivation of the 16 kpbs DCH
return channel for HSDPA feature, if the
PTT feature is enabled.
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
1.2.24.4
Field
Related parameters
Summary of changes
MOCNenabled (Multi-Operator Core Network enabled)
RNC RN6.0 2.0
RNC RN7.0
MultiplePLMNListIncluded of WCEL - To
broadcast multiple PLMN list (IuOperator-PLMNIds) in a cell, this parameter is
set to "Multiple PLMN List broadcasted".
MultiplePLMNListIncluded of WCEL - To
broadcast multiple PLMN list (IuOperator-PLMNIds) in a cell this parameter is
set to 'Multiple PLMN List broadcasted'.
MIBPLMNIdIncluded of RNFC - This
parameter can be modified if MOCNenabled is set to "Disabled".
MIBPLMNIdIncluded of RNFC - This
parameter can be modified if MOCNenabled is set to 'Disabled'.
ICREnabled of WBTS - MOCNenabled is
not allowed to be set to "Enabled" if
ICREnabled has a value "Enabled".
ICREnabled of WBTS - MOCNenabled is
not allowed to be set to "Enabled" if
ICREnabled has a value "Enabled".
CSCNDRXLength of IUO - CSCNDRXLength must be set with same value
among all IU Operators if RNFC-MOCNEnabled parameter is set as enabled.
PSCNDRXLength of IUO - PSCNDRXLength must be set with same value
among all IU Operators if RNFC-MOCNEnabled parameter is set as enabled.
CS_T3212 of IUO - CS_T3212 must be
set with same value among all IU Operators if RNFC-MOCNEnabled parameter
is set as enabled.
PS_NMO of IUO - PS_NMO must be set
with same value among all IU Operators
if RNFC-MOCNEnabled parameter is set
as enabled.
DN00211177
Issue 12B
Id:0900d805809da32a
337
Summary of changes
1.2.24.5
Field
Related parameters
WCDMA Radio Network Configuration Parameters
PSOpThroUsage (Throughput based optimisation of the PS algorithm usage)
RNC RN6.0 2.0
RNC RN7.0
DCHUtilBelowDowngradeThr of RNPS If the parameter PSOpThroUsage is
switched 'On', the value of the related
parameter DCHUtilBelowDowngradeThr
is applicable.
DCHUtilBelowDowngradeThr of RNPS If the parameter PSOpThroUsage is
switched 'On', the value of the related
parameter DCHUtilBelowDowngradeThr
is applicable.
DCHUtilLowerAveWinBitRate of RNPS If the parameter PSOpThroUsage is
switched 'On', the values of the related
parameter DCHUtilLowerAveWinBitRate
are applicable.
DCHUtilLowerAveWinBitRate of RNPS If the parameter PSOpThroUsage is
switched 'On', the values of the related
parameter DCHUtilLowerAveWinBitRate
are applicable.
DCHUtilLowerDowngradeThrBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilLowerDowngradeThrBitRate are applicable.
DCHUtilLowerDowngradeThrBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilLowerDowngradeThrBitRate are applicable.
DCHUtilLowerTimeToTriggerBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilLowerTimeToTriggerBitRate are applicable.
DCHUtilLowerTimeToTriggerBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilLowerTimeToTriggerBitRate are applicable.
DCHUtilMeasGuardTime of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilMeasGuardTime is applicable.
DCHUtilMeasGuardTime of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilMeasGuardTime is applicable.
DCHUtilRelAveWin of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilRelAveWin is applicable.
DCHUtilUpperAveWinBitRate of RNPS If the parameter PSOpThroUsage is
switched 'On', the values of the related
parameter DCHUtilUpperAveWinBitRate
are applicable.
DCHUtilRelThrDL of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilRelThrDL is applicable.
DCHUtilRelThrUL of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilRelThrUL is applicable.
DCHUtilRelTimeToTrigger of RNPS - If
the parameter PSOpThroUsage is
switched 'On', the value of the related
parameter DCHUtilRelTimeToTrigger is
applicable.
338
Id:0900d805809da32a
DCHUtilUpperDowngradeThrBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilUpperDowngradeThrBitRate are applicable.
DCHUtilUpperTimeToTriggerBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilUpperTimeToTriggerBitRate are applicable.
DN00211177
Issue 12B
WCDMA Radio Network Configuration Parameters
Field
RNC RN6.0 2.0
RNC RN7.0
DCHUtilUpperAveWinBitRate of RNPS If the parameter PSOpThroUsage is
switched 'On', the values of the related
parameter DCHUtilUpperAveWinBitRate
are applicable.
DCHUtilRelAveWin of WAC - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilRelAveWin is applicable.
DCHUtilUpperDowngradeThrBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilUpperDowngradeThrBitRate are applicable.
DCHUtilUpperTimeToTriggerBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilUpperTimeToTriggerBitRate are applicable.
1.2.24.6
Field
Related parameters
DN00211177
Issue 12B
Summary of changes
DCHUtilRelThrDL of WAC - If the parameter PSOpThroUsage is switched 'On',
the value of the related parameter
DCHUtilRelThrDL is applicable.
DCHUtilRelThrUL of WAC - If the parameter PSOpThroUsage is switched 'On',
the value of the related parameter
DCHUtilRelThrUL is applicable.
DCHUtilRelTimeToTrigger of WAC - If
the parameter PSOpThroUsage is
switched 'On', the value of the related
parameter DCHUtilRelTimeToTrigger is
applicable.
WireLessPriorityService (Usage of the Wireless Priority Service)
RNC RN6.0 2.0
RNC RN7.0
ADJGId of ADJG - The target cell of
directed retry of WPS call is the cell
whose ADJGId parameter has value
zero.
ADJGId of ADJG - The target cell of
directed retry of WPS call is the cell
whose ADJGId parameter has value
zero.
AdjgSIB of ADJG - If Wireless Priority
Service feature is enabled, then AdjgSIB
shall be set to the default value (Yes).
AdjgSIB of ADJG - If Wireless Priority
Service feature is enabled, then AdjgSIB
must be set with the default value in
ADJG-0 inst