Uploaded by omar.ali.mog

Transmission Line Structure Standard

advertisement
December 29, 2021
December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
TABLE OF CONTENTS
1.
SCOPE
2.
CONTENTS
3.
BILL OF MATERIALS (BOM)
4.
LINE HARDWARE FITTINGS
4.1
INSULATOR ASSEMBLIES / STRINGS
4.2
SHIELDWIRE (OPGW/OGW) FITTINGS
4.3
CONDUCTOR FITTINGS
5.
STRUCTURE GROUNDING DETAILS
6.
STRUCTURE FOUNDATION DETAILS
7.
STRUCTURE, PHASE IDENTIFICATION AND DANGER SIGN PLATE DETAILS
8.
STRUCTURE ANTI-CLIMBING GUARD DETAILS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 2 OF 138
TRANSMISSION CONSTRUCTION STANDARD
1.
TCS-P-122.21, Rev. 01
SCOPE
This Standard describes the details of hardware assemblies, grounding arrangements,
foundations, identifications of structures and phases, anti-climbing and danger sign plates for
steel structures to be used for 69 kV, 110kV, 115 kV, 132kV, 230 kV and 380 kV transmission
lines in the System of National Grid, Saudi Arabia.
The drawings included in this standard show provisional structure details for transmission
lines. Manufacturer/contractor/design engineer shall develop the detailed designs based on
these drawings and considering the requirements specified in the relevant engineering and
material standards.
2.
CONTENTS
2.1
Section 3.0 of this standard contains the Bill of Materials (BOM) for each assembly
drawing along with respective drawing codes.
2.2
Section 4.0 details the arrangement of various types of hardware assemblies such as
conductor suspension, tension / dead end and jumper assemblies for single, twin and
quad bundle conductors, and suspension and tension / dead end assemblies for
conventional and OPGW type overhead ground wires. This section also contains the
details of twin and quad-bundle spacer dampers and full tension conductor splices.
2.3
For standardization purposes, following abbreviations shall be used to describe
various types of hardware assemblies for conductor and overhead ground wire.
2.3.1 SS
Shieldwire Suspension Assembly (first ‘S’ stands for shield wire
and second ‘S’ for suspension)
2.3.2 ST
Shieldwire Tension Assembly (‘S’ stands for shield wire and ‘T’
for Tension)
2.3.3 OPS
Optical Fiber Shieldwire Suspension Assembly (‘OP’ stands for
optical and ‘S’ for suspension).
2.3.4 OPT (S)
Optical Fiber Shieldwire Tension Assembly (‘OP’ stands for
optical and ‘T’ for tension, and ‘S’ for Splicing)
2.3.5 OPT (NS) Optical Fiber Shieldwire Tension Assembly (‘OP’ stands for
optical and ‘T’ for tension, and ‘NS’ for Non-Splicing)
2.3.6 SCS
Single Conductor Suspension Assembly (first ‘S’ stands for
single, ‘C’ for conductor and second ‘S’ for suspension)
2.3.7 SCJS
Single Conductor Jumper Suspension Assembly (first ‘S’ stands
for single, ‘C’ for Conductor ‘J’ for jumper and second ‘S’ for
suspension)
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 3 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
2.3.8 SCDS
Single Conductor Double Suspension Assembly (first ‘S’ stands
for single, ‘C’ for conductor and ‘D’ for double and second ‘S’ for
suspension)
2.3.9 SCT
Single Conductor Tension Assembly (‘S’ stands for single, ‘C’ for
conductor and ‘T’ for tension)
2.3.10 SCDT
Single Conductor Double Tension Assembly (‘S’ stands for
single, ‘C’ for conductor, first ‘D’ for double and second ‘T’ for
tension)
2.3.11 CS (2)
Twin Bundle Conductor Suspension Assembly (‘C’ stands for
conductor, ‘S’ for suspension and ‘(2)’ for twin bundle)
2.3.12 JS (2)
Twin Bundle Conductor Jumper Suspension Assembly (‘J’ stands
for jumper, ‘S’ for suspension and ‘(2)’ for twin bundle)
2.3.13 CDS (2)
Twin Bundle Conductor Double Suspension Assembly (‘C’ stands
for conductor, ‘D’ for double, ‘S’ for suspension and ‘(2)’ for twin
bundle)
2.3.14 CT (2)
Twin Bundle Conductor Tension Assembly (‘C’ stands for
conductor, ‘T’ for tension and ‘(2)’ for twin bundle)
2.3.15 CST (2)
Twin Bundle Conductor Slack Tension Assembly (‘C’ stands for
conductor, ‘S’ for slack, ‘T’ for tension and’ (2)’ for twin bundle)
2.3.16 VS (4)
Quad Bundle Conductor Vee Suspension Assembly (‘V’ stands
for Vee, ‘S’ for suspension and ‘(4)’ for quad bundle)
2.3.17 IS (4)
Quad Bundle Conductor Vertical Single Suspension Assembly (‘I’
stands for vertical, ‘S’ for suspension and ‘(4)’ for quad bundle)
2.3.18 IDS (4)
Quad Bundle Conductor Vertical Double Suspension Assembly
(‘I’ stands for vertical, ‘D’ for double, ‘S’ for suspension and ‘(4)’
for quad bundle)
2.3.19 VJ (4)
Quad Bundle Conductor Vee Jumper Suspension Assembly (‘V’
stands for Vee, ‘J’ for jumper and ‘(4)’ for quad bundle)
2.3.20 VJG (4)
Quad Bundle Conductor Vee Jumper Suspension Assembly (‘V’
stands for Vee, ‘J’ for jumper, ‘G’ for Gantry and ‘(4)’ for quad
bundle)
2.3.21 IJ (4)
Quad Bundle Conductor Vertical Jumper Suspension Assembly
(‘I’ stands for vertical, ‘J’ for jumper and ‘(4) for quad bundle)
2.3.22 CT2 (4)
Quad Bundle Conductor Tension Assembly (‘C’ stands for
conductor, ‘T’ for tension, subscript ‘2’ for double tension strings
and ‘(4)’ for quad bundle)
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 4 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
2.3.23 CST2 (4)
Quad Bundle Conductor Slack Tension Assembly (‘C’ stands for
conductor, ‘S’ for slack, ‘T’ for tension, subscript ‘2’ for double
tension strings and ‘(4)’ for quad bundle)
2.3.24 CT4 (4)
Quad Bundle Conductor Tension Assembly (‘C’ stands for
conductor, ‘T’ for tension, subscript ‘4’ for quad tension strings
and ‘(4)’ for quad bundle)
2.4
Assembly types SS, ST, OPS and OPT (S) & OPT (NS) shall be used for shield wires
(OPGW / OGW) on 69 kV to 380 kV transmission lines.
2.5
Assembly types SCS, SCJS and SCT shall mainly be used for conductors on 69 kV to
132 kV transmission lines.
2.6
Assembly types CS (2), JS (2), CT (2) and CST (2) shall be used on 69 kV to 230kV
transmission lines, whereas assembly types VS (4), IS (4), IDS (4), VJ (4), VJG (4),
IJ (4), CT2 (4), CST2 (4) and CT4 (4) shall mainly be used on 380 kV transmission
lines.
2.7
Assembly types SCDS and CDS (2) shall be used on 69kV to 230kV transmission
lines for overhead crossing with other transmission lines of the same or lower voltage.
However, assembly type SCDT shall be used on 69kV to 230kV single conductor per
phase transmission lines when anchor structures are used for crossing of major
highways/expressways.
2.8
Suspension type insulator assemblies shall not be used on running line angle
suspension structures when line deflection angle exceeds 10º and instead of tension /
dead-end type insulator assemblies shall be used on tension/angle structures.
2.9
The number and type of insulators (porcelain/glass fog type or aero form, porcelain
long rod and composite) required for various types of assemblies to be installed in
National Grid, Saudi Arabia System shall be determined based on creepage distance
requirements as specified in the relevant engineering standard and /or as specified in
the Project Scope of Work/Technical Specifications.
2.10
The rating (vertical load withstand capability) of AGS (Armor Grip Suspension) Unit
shall be at least equal to the rated strength of conductor and shall be 120kN maximum
if rated strength of conductor exceeds 120kN. The rating of AGS Unit shall be reduced
to 80kN & 60kN if rating of OGW/OPGW is 120kN and 70kN respectively.
2.11
The line hardware fittings, when required to be used with heat-resistant type
conductors, shall be suitable for high-temperature operation compatible with the
conductors.
2.12
All line hardware fittings shall be suitable for live-line (hot-line) maintenance and
operations. Necessary provisions such as maintenance holes etc., shall be provided in
the yoke plates and other fittings to facilitate repair / maintenance works.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 5 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
2.13
In case of multiple parallel strings, the spacing between two strings may be increased
to avoid the clashing of strings and to accommodate the arcing/corona devices
particularly for log-rod and composite insulators.
2.14
Section 5.0 describes the various arrangements for grounding of transmission line
latticed type as well as monopole type steel structures. Grounding by means of driven
ground rods, radial and continuous counterpoise arrangements is described.
2.15
Section 6.0 gives the details of various types of foundations to be used in National
Grid, Saudi Arabia System for latticed type steel structures. The foundations covered
in this section include soil pier type, spread footing type, rock-pier type and rock
anchor type.
2.16
Section 7.0 contains the structure, phase identification and danger sign plate details
for latticed steel structures and steel monopole for ground & aerial inspection and
installation of danger sign plate (bone & skull) on latticed steel structures /steel
monopoles.
2.17
Section 8.0 deals with the anti-climbing guard arrangement to be installed on latticed
steel structures and steel monopoles.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 6 OF 138
TRANSMISSION CONSTRUCTION STANDARD
3.0
TCSP12221R01/MAT
TCS-P-122.21, Rev. 01
BILL OF MATERIALS (BOM)
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 7 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
120
Description
Single Conductor Suspension Assembly Type SCS for 69kV
to 132kV with Cap & Pin Suspension Insulators
Figure TC-2221-0100-00
201
Hardware Fitting: Hinge / Universal Joint / Shackle
Pcs
120
1
202
Hardware Fitting: Ball Eye Twisted
Pcs
120
1
203
Hardware Fitting: Arcing Ring Upper (cold end)
Pcs
200
204
205
206
Insulator: Cap & Pin Suspension
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Socket Tongue / Eye Straight
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Pcs
Pcs
Set
111
Set
120
Single Conductor Jumper Suspension Assembly Type SCJS
for 69kV to 132kV with Cap & Pin Suspension Insulators
Figure TC-2221-0200-00
1
120
120
*
1
1
1
201
Hardware Fitting: Hinge / Universal Joint / Shackle
Pcs
120
1
202
Hardware Fitting: Ball Eye Twisted
Pcs
120
1
203
Hardware Fitting: Arcing Ring Upper (cold end)
Pcs
200
Insulator: Cap & Pin Suspension
Pcs
204
205
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Socket Tongue / Eye Straight
206
1
111
*
Pcs
Pcs
120
1
1
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
1
210
Counter Weight Assembly with Bolts
Set
1
211
Counter Weight (25X4=100kg) Or (25X2=50kg) As required
Set
1
Single Conductor Double Suspension Assembly Type SCDS
for 69kV to 132kV with Cap & Pin Suspension Insulators
Figure TC-2221-0300-00
214
215
216
217
218
200
*
Qty
Hardware Fitting: Hinge / Universal Joint / Shackle
Hardware Fitting: Double Tongue Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Cap & Pin Suspension
Set
240
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
240
240
240
120
111
1
1
2
2
2
*
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 8 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
219
205
221
206
Description
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Socket Tongue / Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Single Conductor Tension Assembly Type SCT for 69kV to
132kV with Cap & Pin Suspension Insulators
Figure TC-2221-0400-00
Pcs
Pcs
Pcs
Set
120
180
120
Set
180
Qty
2
2
1
1
223
Hardware Fitting: Hinge / Universal Joint /Shackle
Pcs
180
1
224
225
220
226
227
228
Hardware Fitting: Ball Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Cap & Pin Suspension
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Socket Tongue / Eye Straight
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
180
180
180
1
1
*
1
1
1
229
Hardware Fitting: Compression Dead End Clamp
Set
95 % UTS
1
Set
360
Single Conductor Double Tension Assembly Type SCDT for
69kV to 132kV with Cap & Pin Suspension Insulators
Figure TC-2221-0500-00
*
Breaking
Load (kN)
160
232
233
Hardware Fitting: Hinge / Universal Joint / Shackle
Hardware Fitting: Double Tongue Twisted / Universal Joint
Pcs
Pcs
360
360
1
1
234
235
236
220
237
238
239
228
229
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Cap & Pin Suspension
Hardware Fitting: Socket Tongue / Clevis
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
360
210
2
2
1
*
2
1
1
1
1
160
210
210
180
95 % UTS
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 9 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
120
Description
Single Conductor Suspension Assembly Type SCS for 69kV to
132kV with Porcelain Long Rod insulators
Figure TC-2221-0600-00
241
Hardware Fitting: Hinge / Universal Joint
Pcs
160
1
243
244
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Pcs
Pcs
160
1
1
245
246
247
248
Insulator: Porcelain Long Rod
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Double Tongue / Eye Twisted
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Pcs
Pcs
Set
120
*
1
1
1
Set
120
Single Conductor Jumper Suspension Assembly Type SCJS for
69kV to 132kV with Porcelain Long Rod insulators
Figure TC-2221-0700-00
160
120
241
Hardware Fitting: Hinge / Universal Joint
Pcs
160
1
243
244
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Pcs
Pcs
160
1
1
245
246
Insulator: Porcelain Long Rod
Hardware Fitting: Arcing Ring Lower (hot end)
Pcs
Pcs
120
*
1
247
248
Hardware Fitting: Double Tongue / Eye Twisted
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Set
160
120
1
1
249
251
Counter Weight Assembly with Bolts
Counter Weight (25X4=100kg) Or (25X2=50kg) As required
Set
Set
Single Conductor Double Suspension Assembly Type SCDS
for 69kV to 132kV with Porcelain Long Rod insulators
Figure TC-2221-0800-00
*
Qty
1
1
Set
240
253
254
255
268
244
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue Twisted / Clevis Eye
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue Twisted / Clevis Eye
Hardware Fitting: Arcing Ring Upper (cold end)
Pcs
Pcs
Pcs
Pcs
Pcs
240
240
240
210
1
1
2
4
2
245
Insulator: Porcelain Long Rod
Pcs
120
*
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 10 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
246
256
248
Description
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Double Tongue / Clevis Eye Straight
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Single Conductor Tension Assembly Type SCT for 69kV to
132kV with Porcelain Long Rod insulators
Figure TC-2221-0900-00
242
257
244
250
246
257
260
261
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Single Conductor Double Tension Assembly Type SCDT for
69kV to 132kV with Porcelain Long Rod insulators
Figure TC-2221-1000-00
265
266
267
268
244
250
246
268
260
261
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue Twisted / Clevis Eye
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Single Conductor Suspension Assembly Type SCS for 69kV to
132kV with Composite Insulators
Figure TC-2221-1100-00
272
*
Hardware Fitting: Hinge / Universal Joint
Breaking
Load (kN)
Pcs
Pcs
Set
210
120
Set
180
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
180
180
180
180
95 % UTS
Set
360
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
360
360
360
210
210
180
95 % UTS
Set
120
Pcs
120
Qty
2
1
1
160
160
1
1
1
*
1
1
1
1
1
1
2
4
2
*
2
1
1
1
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 11 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
273
274
275
276
277
278
279
Description
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Composite
Corona Control Ring (hot end)
Hardware Fitting: Arcing Horn Lower (hot end)
Hardware Fitting: Socket Tongue / Eye Straight
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Single Conductor Jumper Suspension Assembly Type SCJS
for 69kV to 132kV with Composite Insulators
Figure TC-2221-1200-00
*
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
120
Set
120
120
120
272
273
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Ball Eye Twisted
Pcs
Pcs
274
275
276
277
278
279
283
284
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Composite
Corona Control Ring (hot end)
Hardware Fitting: Arcing Horn Lower (hot end)
Hardware Fitting: Socket Tongue / Eye Straight
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Counter Weight Assembly with Bolts
Counter Weight (25X4=100kg) Or (25X2=50kg) As required
Pcs
Pcs
Pcs
Pcs
Pcs
Set
Set
Set
Single Conductor Double Suspension Assembly Type SCDS
for 69kV to 132kV with Composite Insulators
Figure TC-2221-1300-00
Breaking
Load (kN)
111
120
120
111
120
120
Set
240
240
240
120
Qty
1
1
*
1
1
1
1
1
1
1
*
1
1
1
1
1
1
287
288
289
290
275
276
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Clevis
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Composite
Corona Control Ring (hot end)
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
291
Hardware Fitting: Arcing Horn Lower (hot end)
Pcs
292
Hardware Fitting: Socket Clevis
Pcs
120
2
293
Hardware Fitting: Clevis Tongue / Eye Twisted
Pcs
180
1
279
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
1
111
1
2
2
2
*
2
2
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 12 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
180
Description
Single Conductor Tension Assembly Type SCT for 69kV to
132kV with Composite Insulators
Figure TC-2221-1400-00
296
297
298
299
300
301
302
303
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue / Ball Eye Straight
Hardware Fitting: Ball Clevis
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Composite
Corona Control Ring (hot end)
Hardware Fitting: Arcing Horn Lower (hot end)
Hardware Fitting: Socket Clevis / Eye
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
180
180
180
180
1
1
1
1
*
1
1
1
304
305
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Pcs
Set
180
95 % UTS
1
1
Set
360
Single Conductor Double Tension Assembly Type SCDT for
69kV to 132kV with Composite Insulators
Figure TC-2221-1500-00
160
308
309
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Pcs
Pcs
360
360
2
2
310
Hardware Fitting: Ball Clevis
Pcs
210
2
311
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
300
Insulator: Composite
Pcs
301
Corona Control Ring (hot end)
Pcs
2
312
Hardware Fitting: Arcing Horn Lower (hot end)
Pcs
1
313
Hardware Fitting: Socket Clevis
Pcs
210
2
314
Hardware Fitting: Hinge / Universal Joint
Pcs
210
1
304
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
180
1
305
Hardware Fitting: Compression Dead End Clamp
Pcs
95 % UTS
1
Set
120
Pcs
120
Twin Bundle Conductor Suspension Assembly Type CS (2)
for 69kV to 230kV with Cap & Pin Suspension Insulators
Figure TC-2221-1600-00
201
*
Qty
Hardware Fitting: Hinge / Universal Joint / Shackle
1
160
*
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 13 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
202
203
200
318
319
320
321
206
Description
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Cap & Pin Suspension
Hardware Fitting: Arcing Horn Lower (hot end)
Hardware Fitting: Socket Tongue / Clevis Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Twin Bundle Conductor Suspension Assembly Type CS (2) for
69kV to 230kV with Cap & Pin Suspension Insulators
Figure TC-2221-1700-00
Pcs
Pcs
120
Pcs
Pcs
111
Pcs
Pcs
Set
120
160
160
120
Set
180
Pcs
Qty
1
1
*
1
1
1
2
2
223
325
326
Hardware Fitting: Hinge / Universal Joint / Shackle
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
Pcs
Pcs
180
180
1
1
1
220
327
328
329
322
206
Insulator: Cap & Pin Suspension
Hardware Fitting: Arcing Horn Lower (hot end)
Hardware Fitting: Socket Tongue / Clevis Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Pcs
Pcs
Pcs
Pcs
Set
160
*
1
1
1
2
2
Set
120
Twin Bundle Conductor Jumper Suspension Assembly Type JS
(2) for 69kV to 230kV with Cap & Pin Suspension Insulators
Figure TC-2221-1800-00
*
Breaking
Load (kN)
180
180
180
120
201
Hardware Fitting: Hinge / Universal Joint / Shackle
Pcs
120
1
202
Hardware Fitting: Ball Eye Twisted
Pcs
120
1
203
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
200
Insulator: Cap & Pin Suspension
Pcs
318
Hardware Fitting: Arcing Horn Lower (hot end)
Pcs
319
Hardware Fitting: Socket Tongue / Clevis Twisted
Pcs
120
1
320
Hardware Fitting: Triangular Yoke Plate
Pcs
160
1
321
Hardware Fitting: Double Tongue Twisted / Shackle
Pcs
160
2
206
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
2
1
111
*
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 14 OF 138
TRANSMISSION CONSTRUCTION STANDARD
Drawing
Code
210
211
Description
Counter Weight Assembly with Bolts
Counter Weight (25X4=100kg) Or (25X2=50kg) As required
Twin Bundle Conductor Double Suspension Assembly Type CDS
(2) for 69kV to 230kV with Cap & Pin Suspension Insulators
Figure TC-2221-1900-00
TCS-P-122.21, Rev. 01
Unit
Breaking
Load (kN)
Set
Set
Qty
1
1
Set
240
214
215
216
217
218
200
327
Hardware Fitting: Hinge / Universal Joint / Shackle
Hardware Fitting: Double Tongue Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis Straight
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Cap & Pin Suspension
Hardware Fitting: Arcing Horn Lower (hot end)
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
240
240
240
120
205
Hardware Fitting: Socket Tongue / Eye Straight
Pcs
120
2
321
206
Hardware Fitting: Double Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Set
160
120
2
2
Set
360
Twin Bundle Conductor Tension Assembly Type CT (2) for 69kV
to 230kV with Cap & Pin Suspension Insulators
Figure TC-2221-2000-00
111
1
2
2
2
2
*
2
232
233
234
336
218
220
337
Hardware Fitting: Hinge / Universal Joint / Shackle
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Cap & Pin Suspension
Hardware Fitting: Arcing Horn Lower (hot end)
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
360
360
360
210
338
Hardware Fitting: Socket Tongue / Clevis Twisted
Pcs
210
2
339
340
228
229
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Double Tongue Twisted / Shackle
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Pcs
Pcs
Pcs
Set
360
210
180
95 % UTS
1
2
2
2
*
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
160
1
1
1
2
2
*
2
PAGE 15 OF 138
TRANSMISSION CONSTRUCTION STANDARD
Drawing
Code
Description
Twin Bundle Conductor Slack Tension Assembly Type CST (2) for
69kV to 230kV with Cap & Pin Suspension Insulators
Figure TC-2221-2100-00
223
224
225
220
226
344
345
322
228
229
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Ball Eye Straight
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Cap & Pin Suspension
Hardware Fitting: Arcing Horn Lower (hot end)
Hardware Fitting: Socket Tongue / Clevis Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue Twisted / Shackle
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Twin Bundle Conductor Suspension Assembly Type CS (2) for
69kV to 230kV with Porcelain Long Rod Insulators
Figure TC-2221-2200-00
241
243
244
245
246
349
350
248
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Twin Bundle Conductor Jumper Suspension Assembly Type JS (2)
for 69kV to 230kV with Porcelain Long Rod Insulators
Figure TC-2221-2300-00
241
243
244
245
246
349
*
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Triangular Yoke Plate
TCS-P-122.21, Rev. 01
Unit
Breaking
Load (kN)
Set
180
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
180
180
180
180
180
180
95 % UTS
Set
120
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
160
160
Set
120
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
160
160
160
120
160
160
120
120
160
Qty
1
1
1
*
1
1
1
2
2
2
1
2
1
*
1
1
2
2
1
2
1
*
1
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 16 OF 138
TRANSMISSION CONSTRUCTION STANDARD
Drawing
Code
350
248
249
251
Description
Hardware Fitting: Double Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Counter Weight Assembly with Bolts
Counter Weight (25X4=100kg) Or (25X2=50kg) As required
Twin Bundle Conductor Double Suspension Assembly Type CDS
(2) for 69kV to 230kV with Porcelain Long Rod Insulators
Figure TC-2221-2400-00
TCS-P-122.21, Rev. 01
Unit
Breaking
Load (kN)
Pcs
Set
Set
Set
160
120
Set
240
Qty
2
2
1
1
354
355
356
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue Straight
Hardware Fitting: Triangular Yoke Plate
Pcs
Pcs
Pcs
240
240
240
1
1
1
357
244
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Pcs
Pcs
210
4
2
245
Insulator: Porcelain Long Rod
Pcs
120
*
246
Hardware Fitting: Arcing Ring Lower (hot end)
Pcs
358
350
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Double Tongue Twisted / Shackle
Pcs
Pcs
280
160
1
2
248
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
2
Set
360
Twin Bundle Conductor Tension Assembly Type CT (2) for 69kV
to 230kV with Porcelain Long Rod Insulators
Figure TC-2221-2500-00
2
265
Hardware Fitting: Hinge / Universal Joint
Pcs
360
1
266
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Pcs
360
1
267
Hardware Fitting: Triangular Yoke Plate
Pcs
360
1
268
244
250
246
365
366
260
261
Hardware Fitting: Double Tongue Twisted / Clevis Eye
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Double Tongue Twisted / Shackle
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
210
4
2
*
2
1
2
2
2
*
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
160
360
210
180
95 % UTS
PAGE 17 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
180
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
180
180
180
180
180
180
95 % UTS
Set
120
Twin Bundle Conductor Slack Tension Assembly Type CST (2)
for 69kV to 230kV with Porcelain Long Rod Insulators
Figure TC-2221-2600-00
242
257
244
250
246
269
370
367
260
261
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Arcing Ring Lower (hot end)
Hardware Fitting: Double Tongue Twisted / Clevis Eye
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue Twisted / Shackle
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Twin Bundle Conductor Suspension Assembly Type CS (2) for
69kV to 230kV with Composite Insulators
Figure TC-2221-2700-00
160
Qty
1
1
1
*
1
1
1
2
2
2
272
273
274
275
276
277
374
375
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Composite
Corona Control Ring (hot end)
Hardware Fitting: Arcing Horn Lower (hot end)
Hardware Fitting: Socket Tongue / Clevis Twisted
Hardware Fitting: Triangular Yoke Plate
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
120
120
120
160
1
1
1
*
1
1
1
1
376
279
Hardware Fitting: Double Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Set
160
120
2
2
Set
120
Pcs
Pcs
Pcs
120
120
Twin Bundle Conductor Jumper Suspension Assembly Type JS
(2) for 69kV to 230kV with Composite Insulators
Figure TC-2221-2800-00
272
273
274
*
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
111
1
1
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 18 OF 138
TRANSMISSION CONSTRUCTION STANDARD
Drawing
Code
275
276
277
374
375
376
279
283
284
TCS-P-122.21, Rev. 01
Description
Insulator: Composite
Corona Control Ring (hot end)
Hardware Fitting: Arcing Horn Lower (hot end)
Hardware Fitting: Socket Tongue / Clevis Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Counter Weight Assembly with Bolts
Counter Weight (25X4=100kg) Or (25X2=50kg) As required
Twin Bundle Conductor Double Suspension Assembly Type CDS
(2) for 69kV to 230kV with Composite Insulators
Figure TC-2221-2900-00
287
288
289
290
275
276
291
292
380
376
279
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Clevis
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Composite
Corona Control Ring (hot end)
Hardware Fitting: Arcing Horn Lower (hot end)
Hardware Fitting: Socket Clevis
Hardware Fitting: Rectangular Yoke
Hardware Fitting: Clevis Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Twin Bundle Conductor Tension Assembly Type CT (2) for 69kV
to 230kV with Composite Insulators
Figure TC-2221-3000-00
*
Unit
Breaking
Qty
Load (kN)
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
Set
Set
111
Set
240
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
240
240
120
Set
360
360
360
210
308
309
310
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Clevis
Pcs
Pcs
Pcs
311
300
301
312
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Composite
Corona Control Ring (hot end)
Hardware Fitting: Arcing Horn Lower (hot end)
Pcs
Pcs
Pcs
Pcs
120
160
160
120
111
120
240
160
120
160
*
1
1
1
1
2
2
1
1
1
1
2
2
*
2
2
2
1
2
2
2
1
2
1
*
2
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 19 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Description
313
Hardware Fitting: Socket Clevis
Pcs
210
2
384
Hardware Fitting: Rectangular Yoke
Pcs
360
1
385
Hardware Fitting: Clevis Tongue Twisted / Shackle
Pcs
210
2
304
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
180
2
305
Hardware Fitting: Compression Dead End Clamp
Set
95 % UTS
2
Set
180
Twin Bundle Conductor Slack Tension Assembly Type CST (2)
for 69kV to 230kV with Composite Insulators
Figure TC-2221-3100-00
*
Breaking
Qty
Load (kN)
296
Hardware Fitting: Hinge / Universal Joint
Pcs
180
1
388
Hardware Fitting: Ball Eye Straight
Pcs
180
1
299
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
300
Insulator: Composite
Pcs
301
Corona Control Ring (hot end)
Pcs
1
302
Hardware Fitting: Arcing Horn Lower (hot end)
Pcs
1
303
Hardware Fitting: Socket Clevis
Pcs
180
1
377
Hardware Fitting: Double Tongue Twisted / Shackle
Pcs
180
1
389
Hardware Fitting: Triangular Yoke Plate
Pcs
180
1
377
Hardware Fitting: Double Tongue Twisted / Shackle
Pcs
180
2
304
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
180
2
305
Hardware Fitting: Compression Dead End Clamp
Set
95 % UTS
2
1
160
*
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 20 OF 138
TRANSMISSION CONSTRUCTION STANDARD
Drawing
Code
Description
Quad Bundle Conductor Vee Suspension (Square Orientation)
Assembly Type VS (4) for 380kV with Cap & Pin Insulators
Figure TC-2221-3200-00
401
402
403
404
400
405
406
407
408
409
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Eye Straight
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Suspension Cap & Pin
Hardware Fitting: Socket Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Hardware Fitting: Clevis Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Quad Bundle Conductor Vee Suspension (Diamond Orientation)
Assembly Type VS (4) for 380kV with Cap & Pin Insulators
Figure TC-2221-3300-00
401
402
403
404
400
405
406
413
408
409
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Eye Straight
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Suspension Cap & Pin
Hardware Fitting: Socket Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Hardware Fitting: Quad Yoke Plate (Diamond Configuration)
Hardware Fitting: Clevis Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Quad Bundle Conductor Vertical Suspension (Square Orientation)
Assembly Type IS (4) for 380kV with Cap & Pin Insulators
Figure TC-2221-3400-00
401
417
404
400
*
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Ball Eye Straight
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Suspension Cap & Pin
TCS-P-122.21, Rev. 01
Unit
Breaking
Load (kN)
Set
360
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
180
180
210
Set
360
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
180
180
210
Set
180
Pcs
Pcs
Pcs
Pcs
180
210
160
210
180
180
120
160
210
180
180
120
160
Qty
2
2
2
2
*
2
2
1
4
4
2
2
2
2
*
2
2
1
4
4
1
1
1
*
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 21 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Description
Unit
405
406
418
Hardware Fitting: Socket Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Pcs
Pcs
Pcs
210
180
1
1
1
408
409
Hardware Fitting: Clevis Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Set
180
120
4
4
Set
360
Quad Bundle Conductor Vertical Double Suspension (Square
Orientation) Assembly Type IDS (4) for 380kV with Cap &
Pin Insulators
Figure TC-2221-3500-00
421
422
423
403
424
400
405
406
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Suspension Cap & Pin
Hardware Fitting: Socket Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
360
360
360
210
425
408
409
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Hardware Fitting: Clevis Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Pcs
Set
180
180
120
Set
360
Quad Bundle Conductor Vee Jumper Suspension (Square
Orientation) Assembly Type VJ (4) for 380kV with Cap &
Pin Insulators
Figure TC-2221-3600-00
*
Breaking
Qty
Load (kN)
160
210
1
1
1
2
2
*
2
2
1
4
4
401
402
403
404
400
405
406
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Eye Straight
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Suspension Cap & Pin
Hardware Fitting: Socket Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
180
180
210
407
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Pcs
180
1
408
Hardware Fitting: Clevis Tongue Twisted / Shackle
Pcs
180
4
160
210
2
2
2
2
*
2
2
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 22 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Description
Unit
409
428
429
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Counter Weight Assembly with Bolts
Counter Weight (50X4=200kg) Or (50X2=100kg) As required
Set
Set
Set
120
Set
360
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
180
180
210
Set
180
Quad Bundle Conductor Vee Jumper Suspension (Square
Orientation) Assembly Type VJG (4) for 380kV with Cap & Pin
Insulators
Figure TC-2221-3700-00
401
412
403
404
400
405
406
407
408
409
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Eye Straight
Hardware Fitting: Ball Eye Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Suspension Cap & Pin
Hardware Fitting: Socket Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Hardware Fitting: Clevis Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Quad Bundle Conductor Vertical Jumper Suspension (Square
Orientation) Assembly Type IJ (4) for 380kV with Cap & Pin
Insulators
Figure TC-2221-3800-00
*
Breaking
Load (kN)
160
210
180
180
120
Qty
4
1
1
2
2
2
2
*
2
2
1
4
4
401
417
404
400
405
406
Hardware Fitting: Hinge / Universal Joint /
Hardware Fitting: Ball Eye Straight
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Suspension Cap & Pin
Hardware Fitting: Socket Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
180
210
433
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Pcs
180
1
408
Hardware Fitting: Clevis Tongue Twisted / Shackle
Pcs
180
4
409
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
4
428
Counter Weight Assembly with Bolts
Set
1
429
Counter Weight (50X4=200kg) Or (50X2=100kg) As required
Set
1
160
210
1
1
1
*
1
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 23 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
460
Description
Quad Bundle Conductor Tension (Square Orientation)
Assembly Type CT2 (4) for 380kV with Cap & Pin Insulators
Figure TC-2221-3900-00
438
439
440
441
442
450
443
444
445
446
447
448
449
Hardware Fitting: Hinge / Universal Joint / Shackle
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Insulator: Suspension Cap & Pin
Hardware Fitting: Socket Tongue / Clevis
Hardware Fitting: Yoke with Strap
Hardware Fitting: Ball Eye / Clevis
Hardware Fitting: Socket Tongue / Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Double Tongue Twisted / Universal Joint
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
460
460
460
230
460
230
1
1
1
2
2
*
2
1
2
2
1
1
2
451
452
453
454
455
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Pcs
Pcs
Pcs
Set
Set
340
210
210
180
95 % UTS
2
2
2
4
4
Set
460
Quad Bundle Conductor Tension (Diamond Orientation)
Assembly Type CT2 (4) for 380kV with Cap & Pin Insulators
Figure TC-2221-4000-00
*
Qty
210
230
460
230
230
438
Hardware Fitting: Hinge / Universal Joint / Shackle
Pcs
460
1
439
Hardware Fitting: Double Tongue Twisted
Pcs
460
1
440
Hardware Fitting: Triangular Yoke Plate
Pcs
460
1
441
Hardware Fitting: Ball Eye / Clevis Twisted
Pcs
230
2
442
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
450
Insulator: Suspension Cap & Pin
Pcs
210
*
443
Hardware Fitting: Socket Tongue / Clevis
Pcs
230
2
444
Hardware Fitting: Yoke with Strap
Pcs
460
1
445
Hardware Fitting: Ball Eye / Clevis
Pcs
230
2
2
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 24 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
*
Description
Breaking
Load (kN)
Qty
446
447
460
Hardware Fitting: Socket Tongue / Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Hardware Fitting: Trapezoid Yoke Plate
Pcs
Pcs
Pcs
230
460
2
1
1
461
462
463
464
465
466
454
455
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Clevis Tongue / Eye Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
Set
210
210
360
210
210
210
180
95 % UTS
1
2
1
1
2
1
4
4
Quad Bundle Conductor Slack Tension (Square Orientation)
Assembly Type CST2 (4) for 380kV with Cap & Pin Insulators
Figure TC-2221-4100-00
Set
440
470
471
472
473
442
Hardware Fitting: Hinge / Universal Joint / Shackle
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
Pcs
Pcs
Pcs
Pcs
360
360
360
180
1
1
1
2
2
450
474
475
445
446
Insulator: Suspension Cap & Pin
Hardware Fitting: Socket Tongue / Clevis
Hardware Fitting: Yoke with Strap
Hardware Fitting: Ball Eye / Clevis
Hardware Fitting: Socket Tongue / Clevis Twisted
Pcs
Pcs
Pcs
Pcs
Pcs
210
180
360
230
230
*
2
1
2
2
447
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Pcs
476
Hardware Fitting: Trapezoid Yoke Plate
Pcs
360
1
449
477
452
453
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
Pcs
Pcs
Pcs
230
320
210
210
2
2
2
2
454
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Set
180
4
455
Hardware Fitting: Compression Dead End Clamp
Set
95 % UTS
4
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 25 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
440
Description
Quad Bundle Conductor Slack Tension (Diamond Orientation)
Assembly Type CST2 (4) for 380kV with Cap & Pin Insulators
Figure TC-2221-4200-00
Qty
470
Hardware Fitting: Hinge / Universal Joint / Shackle
Pcs
360
1
471
472
473
442
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
Pcs
Pcs
Pcs
360
360
180
1
1
2
2
450
474
475
445
446
447
481
482
483
477
484
485
486
Insulator: Suspension Cap & Pin
Hardware Fitting: Socket Tongue / Clevis
Hardware Fitting: Yoke with Strap
Hardware Fitting: Ball Eye / Clevis
Hardware Fitting: Socket Tongue / Clevis Twisted
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Clevis Tongue / Eye Twisted
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
210
180
360
230
230
360
210
210
320
210
210
210
*
2
1
2
2
1
1
1
2
1
1
2
1
454
455
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Set
Set
180
95 % UTS
4
4
Set
860
Quad Bundle Conductor Tension (Square Orientation) Assembly
Type CT4 (4) for 380kV with Cap & Pin Insulators
Figure TC-2221-4300-00
489
490
491
Hardware Fitting: Hinge / Universal Joint / Shackle
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Triangular Yoke Plate
Pcs
Pcs
Pcs
860
860
860
1
1
1
492
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Pcs
460
2
493
Hardware Fitting: Triangular Yoke Plate
Pcs
460
2
494
Hardware Fitting: Ball Eye / Clevis Straight
Pcs
240
4
495
*
Hardware Fitting: Arcing Horn upper (cold end)
Pcs
2
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 26 OF 138
TRANSMISSION CONSTRUCTION STANDARD
Drawing
Code
Description
TCS-P-122.21, Rev. 01
Unit
Breaking
Load (kN)
Qty
450
Insulator: Suspension Cap & Pin
Pcs
210
*
496
Hardware Fitting: Socket Tongue / Clevis
Pcs
240
4
497
Hardware Fitting: Ball Eye / Clevis
Pcs
240
4
498
Hardware Fitting: Yoke with Strap
Pcs
860
2
499
Hardware Fitting: Socket Tongue / Clevis Twisted
240
4
500
Hardware Fitting: Guard Ring / Arc Racket Lower (hot end)
Pcs
501
502
503
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Yoke with Strap
Pcs
Pcs
Pcs
860
240
860
2
4
2
504
Hardware Fitting: Double Tongue Straight / Universal Joint
Pcs
240
2
505
454
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
Set
240
180
2
4
455
Hardware Fitting: Compression Dead End Clamp
Set
95 % UTS
4
Set
360
Quad Bundle Conductor Vee Suspension (Square Orientation)
Assembly Type VS (4) for 380kV with Porcelain Long Rod
Insulators
Figure TC-2221-4400-00
1
515
516
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Double Eye Straight
Pcs
Pcs
210
210
2
2
517
518
519
520
Hardware Fitting: Clevis Tongue / Double Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Pcs
Pcs
Pcs
Pcs
210
320
2
6
2
*
521
Hardware Fitting: Intermediate Arcing Ring
Pcs
4
522
Hardware Fitting: Guard Ring / Arcing Ring lower (hot end)
Pcs
2
523
524
Hardware Fitting: Clevis Tongue / Eye Straight
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Pcs
Pcs
320
210
2
1
525
Hardware Fitting: Clevis Tongue Twisted / Shackle
Pcs
210
4
526
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
4
*
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
160
PAGE 27 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
360
Description
Quad Bundle Conductor Vee Jumper Suspension (Square
Orientation) Assembly Type VJ (4) for 380kV with Porcelain
Long Rod Insulators
Figure TC-2221-4500-00
515
Hardware Fitting: Hinge / Universal Joint
Pcs
210
2
516
517
Hardware Fitting: Clevis Tongue / Double Eye Straight
Hardware Fitting: Clevis Tongue / Double Eye Straight
Pcs
Pcs
210
210
2
2
518
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Pcs
320
6
519
520
521
522
523
524
525
526
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Intermediate Arcing Ring
Hardware Fitting: Guard Ring / Arcing Ring lower (hot end)
Hardware Fitting: Clevis Tongue / Eye Straight
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Hardware Fitting: Clevis Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
531
Counter Weight Assembly with Bolts
Set
1
532
Counter Weight (50X4=200kg) Or (50X2=100kg) As required
Set
1
Quad Bundle Conductor Vee Jumper Suspension (Square
Orientation) Assembly Type VJG (4) for 380kV with Porcelain
Long Rod Insulators
Figure TC-2221-4600-00
*
Qty
160
320
210
210
120
Set
360
2
*
4
2
2
1
4
4
515
518
519
520
521
522
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Intermediate Arcing Ring
Hardware Fitting: Guard Ring / Arcing Ring lower (hot end)
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
210
320
523
Hardware Fitting: Clevis Tongue / Eye Straight
Pcs
320
2
524
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Pcs
210
1
525
Hardware Fitting: Clevis Tongue Twisted / Shackle
Pcs
210
4
526
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
4
160
2
6
2
*
4
2
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 28 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
180
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Set
Set
Set
210
320
Set
680
Description
Quad Bundle Conductor Vertical Jumper Suspension (Square
Orientation) Assembly Type IJ (4) for 380kV with Porcelain
Long Rod Insulators
Figure TC-2221-4700-00
515
518
519
520
521
522
523
537
525
526
531
532
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Intermediate Arcing Ring
Hardware Fitting: Guard Ring / Arcing Ring lower (hot end)
Hardware Fitting: Clevis Tongue / Eye Straight
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Hardware Fitting: Clevis Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Counter Weight Assembly with Bolts
Counter Weight (50X4=200kg) Or (50X2=100kg) As required
Quad Bundle Conductor Tension (Square Orientation)
Assembly Type CT2 (4) for 380kV with Porcelain Long Rod
Insulators
Figure TC-2221-4800-00
*
Qty
1
3
1
*
2
1
1
1
4
4
1
1
160
320
210
210
120
546
547
548
549
550
551
552
553
554
555
556
557
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Eye Straight
Hardware Fitting: Double Tongue / Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Intermediate Arcing Ring
Hardware Fitting: Guard Ring / Arcing Ring lower (hot end)
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
340
360
340
340
680
340
340
210
2
1
6
2
*
4
2
2
1
2
2
2
558
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
210
2
559
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
210
4
560
Hardware Fitting: Compression Dead End Clamp
Set
95 % UTS
4
330
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 29 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
440
Description
Quad Bundle Conductor Slack Tension (Square Orientation)
Assembly Type CST2 (4) for 380kV with Porcelain Long Rod
Insulators
Figure TC-2221-4900-00
566
567
568
549
570
551
552
569
571
572
573
557
558
559
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Eye Straight
Hardware Fitting: Double Tongue / Eye Straight
Hardware Fitting: Arcing Ring Upper (cold end)
Insulator: Porcelain Long Rod
Hardware Fitting: Intermediate Arcing Ring
Hardware Fitting: Guard Ring / Arcing Ring lower (hot end)
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
360
360
320
320
440
320
320
210
210
210
2
1
6
2
*
4
2
2
1
2
2
2
2
4
560
Hardware Fitting: Compression Dead End Clamp
Set
95 % UTS
4
Set
360
180
180
210
Quad Bundle Conductor Vee Suspension (Square Orientation)
Assembly Type VS (4) for 380kV with Composite Insulators
Figure TC-2221-5000-00
*
Qty
210
600
601
602
603
604
605
606
607
608
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Double Eye Straight
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Hardware Fitting: Corona Control Ring (cold end)
Insulator: Composite
Hardware Fitting: Corona Control Ring (hot end)
Hardware Fitting: Socket Clevis Twisted
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
210
180
2
2
2
2
2
*
2
2
1
609
Hardware Fitting: Clevis Tongue Twisted / Shackle
Pcs
180
4
610
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
4
160
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 30 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
360
180
180
210
Description
Quad Bundle Conductor Vee Suspension (Diamond Orientation)
Assembly Type VS (4) for 380kV with Composite Insulators
Figure TC-2221-5100-00
Qty
600
601
602
603
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Double Eye Straight
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
Pcs
Pcs
Pcs
604
Hardware Fitting: Corona Control Ring (cold end)
Pcs
605
Insulator: Composite
606
Hardware Fitting: Corona Control Ring (hot end)
Pcs
607
Hardware Fitting: Socket Clevis Twisted
Pcs
210
2
615
Hardware Fitting: Quad Yoke Plate (Diamond Orientation)
Pcs
180
1
609
Hardware Fitting: Clevis Tongue Twisted / Shackle
Pcs
180
4
610
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
4
Set
360
180
180
210
2
160
Quad Bundle Conductor Vee Jumper Suspension (Square
Orientation) Assembly Type VJ (4) for 380kV with Composite
Insulators
Figure TC-2221-5200-00
2
2
2
2
*
2
600
601
602
603
604
605
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Clevis Tongue / Double Eye Straight
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Hardware Fitting: Corona Control Ring (cold end)
Insulator: Composite
Pcs
Pcs
Pcs
Pcs
Pcs
606
Hardware Fitting: Corona Control Ring (hot end)
Pcs
607
Hardware Fitting: Socket Clevis Twisted
Pcs
210
2
608
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Pcs
180
1
609
Hardware Fitting: Clevis Tongue Twisted / Shackle
Pcs
180
4
610
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Set
120
4
620
621
Counter Weight Assembly with Bolts
Counter Weight (50X4=200kg) Or (50X2=100kg) As required
Set
Set
*
160
2
2
2
2
2
*
2
1
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 31 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Set
360
180
210
Description
Quad Bundle Conductor Vee Jumper Suspension (Square
Orientation) Assembly Type VJG (4) for 380kV with Composite
Insulators
Figure TC-2221-5300-00
600
602
603
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
Pcs
Pcs
604
605
606
607
608
609
610
Hardware Fitting: Corona Control Ring (cold end)
Insulator: Composite
Hardware Fitting: Corona Control Ring (hot end)
Hardware Fitting: Socket Clevis Twisted
Hardware Fitting: Quad Yoke Plate (Square Orientation)
Hardware Fitting: Clevis Tongue Twisted / Shackle
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Quad Bundle Conductor Tension (Square Orientation) Assembly
Type CT4 (4) for 380kV with Composite Insulators
Figure TC-2221-5400-00
*
160
Pcs
Pcs
Pcs
Pcs
Set
210
180
180
120
Set
680
628
629
630
631
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Arcing Horn Upper (cold end)
Hardware Fitting: Double Tongue Twisted / Universal Joint
Pcs
Pcs
Pcs
Pcs
680
680
632
633
634
605
636
637
638
639
640
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Corona Control Ring (cold end)
Insulator: Composite
Hardware Fitting: Corona Control Ring (hot end)
Hardware Fitting: Socket Tongue / Clevis
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Guard Ring / Arcing Racket (hot end)
Hardware Fitting: Double Tongue Twisted / Universal Joint
Pcs
Pcs
Pcs
360
210
641
Hardware Fitting: Yoke with Strap
642
360
Qty
2
2
2
2
*
2
2
1
4
4
1
1
1
2
210
2
4
4
*
4
4
2
1
4
Pcs
340
2
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
180
2
643
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
210
2
644
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
180
4
160
Pcs
Pcs
Pcs
Pcs
Pcs
230
680
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 32 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Qty
Set
95 % UTS
4
Set
680
645
Description
Hardware Fitting: Compression Dead End Clamp
Quad Bundle Conductor Tension (Diamond Orientation)
Assembly Type CT4 (4) for 380kV with Composite Insulators
Figure TC-2221-5500-00
628
Hardware Fitting: Hinge / Universal Joint
Pcs
680
1
629
Hardware Fitting: Triangular Yoke Plate
Pcs
680
1
630
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
631
632
633
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis Twisted
Pcs
Pcs
Pcs
634
Hardware Fitting: Corona Control Ring (cold end)
Pcs
605
636
637
Insulator: Composite
Hardware Fitting: Corona Control Ring (hot end)
Hardware Fitting: Socket Tongue / Clevis
Pcs
Pcs
230
*
4
4
651
Hardware Fitting: Trapezoid Yoke Plate
Pcs
680
2
639
640
652
653
654
Hardware Fitting: Guard Ring / Arcing Racket (hot end)
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
Pcs
Pcs
Pcs
Pcs
210
360
320
180
1
6
1
2
1
655
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
210
2
656
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
210
1
644
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
180
4
645
Hardware Fitting: Compression Dead End Clamp
Set
95 % UTS
4
Quad Bundle Conductor Slack Tension (Square Orientation)
Assembly Type CST2 (4) for 380kV with Composite
Insulators
Figure TC-2221-5600-00
Set
440
Hardware Fitting: Hinge / Universal Joint
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Pcs
Pcs
Pcs
360
360
360
665
631
632
*
1
360
360
210
2
2
4
4
160
1
1
1
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 33 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Breaking
Load (kN)
Qty
230
230
2
2
Description
666
667
Hardware Fitting: Clevis Tongue / Ball Clevis Twisted
Hardware Fitting: Ball Eye Straight
Pcs
Pcs
668
Hardware Fitting: Arcing Horn Upper (cold end)
Pcs
2
669
670
671
672
673
674
675
676
642
643
Hardware Fitting: Corona Control Ring (cold end)
Insulator: Composite
Hardware Fitting: Corona Control Ring Lower (hot end)
Hardware Fitting: Socket Tongue / Clevis
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Guard Ring / Arcing Racket (hot end)
Hardware Fitting: Double Tongue Twisted / Universal Joint
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
210
240
180
210
2
*
2
2
1
1
2
2
2
2
644
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Pcs
180
4
645
Hardware Fitting: Compression Dead End Clamp
Set
95 % UTS
4
Set
440
Quad Bundle Conductor Slack Tension (Diamond
Orientation) Assembly Type CST2 (4) for 380kV with
Composite Insulators
Figure TC-2221-5700-00
*
210
230
440
665
Hardware Fitting: Hinge / Universal Joint
Pcs
360
1
631
Hardware Fitting: Double Tongue Twisted / Universal Joint
Pcs
360
1
632
682
668
669
Hardware Fitting: Triangular Yoke Plate
Hardware Fitting: Ball Eye / Clevis Twisted
Hardware Fitting: Arcing Horn Upper (cold end)
Hardware Fitting: Corona Control Ring (cold end)
Pcs
Pcs
Pcs
Pcs
360
230
1
2
2
2
670
671
672
683
674
684
685
Insulator: Composite
Hardware Fitting: Corona Control Ring Lower (hot end)
Hardware Fitting: Socket Tongue / Clevis
Hardware Fitting: Trapezoid Yoke Plate
Hardware Fitting: Guard Ring / Arcing Racket (hot end)
Hardware Fitting: Double Tongue / Clevis Eye Twisted
Hardware Fitting: Triangular Yoke Plate
210
*
2
2
1
1
2
1
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
230
440
210
240
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 34 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Description
Unit
Breaking
Load (kN)
Qty
686
687
688
689
644
645
Hardware Fitting: Extension Link
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Double Tongue / Clevis Eye Straight
Hardware Fitting: Adjustable Extension Link 265 to 450 mm
Hardware Fitting: Compression Dead End Clamp
Pcs
Pcs
Pcs
Pcs
Pcs
Set
180
180
210
210
180
95 % UTS
2
1
2
1
4
4
Set
70/120
120
120
60/80
Optical Fiber (OPGW) Shieldwire Suspension Assembly Type
OPS
Figure TC-2221-5800-00
715
716
717
Hardware Fitting: Shackle
Hardware Fitting: Double Eye Twisted / Chain Link
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Pcs
Pcs
Pcs
718
Hardware Fitting: Parallel Groove Clamp
Pcs
1
719
Hardware Fitting: Tower Connection Clamp
Pcs
1
Optical Fiber (OPGW) Shieldwire Tension Assembly (Splicing)
Type OPT (S)
Figure TC-2221-5900-00
715
724
725
726
727
728
Hardware Fitting: Shackle
Hardware Fitting: Chain Link / Clevis Eye Straight
Hardware Fitting: Thimble Clevis
Hardware Fitting: Preformed Dead End
Hardware Fitting: Parallel Groove Clamp
Hardware Fitting: Tower Connection / Earthing Clamp
Optical Fiber (OPGW) Shieldwire Tension Assembly (Non
Splicing) Type OPT (NS)
Figure TC-2221-6000-00
Set
120
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
120
140
120
95 % UTS
Set
120
1
1
1
1
1
1
1
1
1
715
724
Hardware Fitting: Shackle
Hardware Fitting: Chain Link / Clevis Eye Straight
Pcs
Pcs
120
140
1
1
725
726
Hardware Fitting: Thimble Clevis
Hardware Fitting: Preformed Dead End
Pcs
Pcs
120
95 % UTS
1
1
*
Insulators as per relevant TES & TMSS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 35 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
727
728
Description
Hardware Fitting: Parallel Groove Clamp
Hardware Fitting: Tower Connection / Earthing Clamp
Breaking
Load (kN)
Pcs
Pcs
Qty
1
1
Vibration Damper for OPGW
Figure TC-2221-6100-00
Shieldwire (OGW) Suspension Assembly Type SS
Figure TC-2221-6200-00
Set
70/120
735
736
737
738
Hardware Fitting: Shackle
Hardware Fitting: Double Eye Twisted / Chain Link
Suspension Unit: Armor Grip Suspension (AGS) Clamp
Hardware Fitting: Parallel Groove Clamp
Pcs
Pcs
Pcs
Pcs
120
120
60/80
739
Hardware Fitting: Tower Connection / Earthing Clamp
Pcs
Shieldwire (OGW) Tension Assembly Type ST
Set
120
Pcs
Pcs
Pcs
Pcs
120
95% UTS
1
1
1
1
1
Figure TC-2221-6300-00
735
740
741
742
Hardware Fitting: Shackle
Hardware Fitting: Compression Deadend Clamp
Hardware Fitting: Parallel Groove Clamp
Hardware Fitting: Tower Connection / Earthing Clamp
1
1
1
1
Vibration Damper for OGW
Figure TC-2221-6400-00
Conductor Splice, Repair Sleeve, Quad & Twin bundle Spacer
Dampers, Vibration Damper and ACSR/AW Condor
Conductor
FIGURE TC-2221-6500-00 to FIGURE TC-2221-7000-00
Full Tension Splice / Compression Mid span Joint
FIGURE TC-2221-6500-00
TCSP12221R01/MAT
EA
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 36 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
Drawing
Code
Unit
Description
Breaking
Load
(kN)
Qty
Compression Repair Sleeve
FIGURE TC-2221-6600-00
EA
Quad Spacer Damper (450mm bundle spacing)
FIGURE TC-2221-6700-00
EA
Twin Spacer Damper (450mm bundle spacing)
FIGURE TC-2221-6800-00
EA
Vibration Damper for Conductors
FIGURE TC-2221-6900-00
EA
ACSR/AW Condor Conductors
FIGURE TC-2221-7000-00
EA
Latticed Steel Tower and Steel Pole Grounding
Figure TC-2221-7100-00 ----- Figure TC-2221-8000-00
765
766
767
768
769
770
771
772
773
774
*
Counterpoise as per TES-P-122.10
Compression Terminal Lug
Ground Rod 16 mm (5/8 inch) 3000 mm Length
Mold: Thermite Welding, Type GR
Mold: Thermite Welding, Type GT
Mold: Thermite Welding, Type SS
Compound: Galvanic Corrosion, Inhibitor
Mold: Thermite Welding, Type RRC
Mold: Thermite Welding, Type VSC
Galvanized Steel Wire Or Copper Clad Steel Grounding
Conductor AWG
m
EA
EA
EA
EA
EA
EA
EA
EA
*
*
*
*
*
*
*
*
*
m
*
Quantities to be determined by the manufacturer
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 37 OF 138
TRANSMISSION CONSTRUCTION STANDARD
Drawing
Code
Description
TCS-P-122.21, Rev. 01
Unit
Breaking
Load (kN)
Qty
Structure Foundation Details
Foundation Layout Plan
FIGURE TC-2221-8100-00
EA
Pier Type Foundation
FIGURE TC-2221-8200-00
EA
Spread Footing Type Foundation
FIGURE TC-2221-8300-00
EA
Rock Pier Type Foundation
FIGURE TC-2221-8400-00
EA
Rock Anchor Type Foundation
FIGURE TC-2221-8500-00
EA
Structure Identification Detail (Aerial / Ground Inspection,
Phase & Danger Plates)
Figure TC-2221-8600-00 ----- Figure TC-2221-9200-00
784
Tag: Metal, Aluminum, Tower Identification,
125x175x1 mm, Black Embossed Letter 150 mm High on
Yellow Background, As Required Letter
Tag: Metal, Aluminum, Tower Identification,
125x175x1 mm, Black Embossed Digit 150 mm High on
Yellow Background, As Required Digit
Tag: Metal, Aluminum, Tower Identification,
60x90x1 mm, Black Embossed Letter 75 mm High on Yellow
Background, As Required Letter
Tag: Metal, Aluminum, Tower Identification,
60x90x1 mm Black Embossed Digit 75 mm High on Yellow
Background, As Required Digit
Holder: Channel, Vertical, For 60x90 mm Tower ID Tags
785
Holder: Channel, Horizontal, for 125x175 mm Tower ID Tags
EA
786
Bar: Flat, Galvanized, Steel, 3x40x610 mm
EA
787
Bar: Flat, Galvanized, Steel, 3x40x825 mm
EA
788
Bolt: Steel, Hex Head With Nut, Galvanized, 10x40 mm.
EA
780
781
782
783
TCSP12221R01/MAT
EA
*
EA
*
EA
*
EA
*
EA
*
*
*
*
*
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 38 OF 138
TRANSMISSION CONSTRUCTION STANDARD
Drawing
Code
789
790
791
792
793
794
795
796
797
TCS-P-122.21, Rev. 01
Breaking
Load (kN)
Description
Unit
Qty
Washer: Spring Lock, Stainless Steel 11.5 mm diameter
Washer: Round, Stainless Steel 11.5 mm diameter
Stud: Steel, Shot-Fired, 10 mm diameter x 6 mm Long
Holder: Channel, Vertical, for 125x175 mm Tower ID Tags
Plate: Phase, Identification, Aluminum, 100 mm diameter
Bolt: M10, Complete with flat & spring washers, nut and lock
nut (all of stainless steel)
Bar: Flat, Galvanized, 4 mm Thickness, Length As Required
Sign: Danger, High Voltage (Bone & Skull)
255x510 mm, C=25
Bolt: M14 with nut and washer (all of stainless steel)
EA
EA
EA
EA
EA
*
*
*
*
*
EA
*
EA
*
EA
*
EA
*
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
*
*
*
*
*
*
*
*
*
*
*
* Quantities to be determined by the manufacturer
Anti-Climbing Guard Details (Towers & Steel Poles)
Figure TC-2221-9300-00 ---Figure TC-2221-9500-00
800
801
802
803
804
805
806
807
808
809
810
Washer: Lock, Galvanized, For 14 mm Diameter Bolt
Washer: Round, Galvanized, For 14 mm Diameter Bolt
Bar: Angle, Galvanized, 50x50x6 mm, 1550 mm Long
Fastener: Steel, Galvanized, 27x90x6 mm
Bolt: Machine, Galvanized, M14x60 mm Long
Bolt: Machine, Galvanized, M14x35 mm Long
Wire: Barbed, Galvanized
Frame: Angle, Galvanized, 40x40x4 mm, Length As Required
Device: Locking, Complete with L-key and M14 bolt
Frame: Steel, Galvanized, Bar 40x5 mm, Length As Required
Bolt: Steel, Galvanized, M14x50 with nut & washer
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 39 OF 138
TRANSMISSION CONSTRUCTION STANDARD
4.1
TCSP12221R01/MAT
TCS-P-122.21, Rev. 01
INSULATOR ASSEMBLIES / STRINGS
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 40 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-0100-00
SINGLE CONDUCTOR SUSPENSION ASSEMBLY SCS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 41 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-0200-00
SINGLE CONDUCTOR JUMPER SUSPENSION ASSEMBLY SCJS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 42 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-0300-00
SINGLE CONDUCTOR DOUBLE SUSPENSION ASSEMBLY SCDS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES AND ON SMALL RUNNING
ANGLE TYPE SUSPENSION STRUCTURES WHEN THERE IS AN OVERHEAD LINE CROSSING WITH
ANOTHER TRANSMISSION LINE.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 43 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-0400-00
SINGLE CONDUCTOR TENSION ASSEMBLY SCT
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR ALL TYPES OF TENSION/ANGLE AND TERMINAL/
DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 44 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-0500-00
SINGLE CONDUCTOR DOUBLE TENSION ASSEMBLY SCDT
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TENSION/TERMINAL/DEADEND TOWERS FOR CROSSING
OF MAJOR HIGHWAYS/EXPRESSWAYS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL AND SHALL BE PORCELAIN/GLASS
FOG TYPE OR AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 45 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-0600-00
SINGLE CONDUCTOR SUSPENSION ASSEMBLY SCS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 46 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-0700-00
SINGLE CONDUCTOR JUMPER SUSPENSION ASSEMBLY SCJS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 47 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-0800-00
SINGLE CONDUCTOR DOUBLE SUSPENSION ASSEMBLY SCDS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES AND ON SMALL RUNNING
ANGLE TYPE SUSPENSION STRUCTURES WHEN THERE IS AN OVERHEAD LINE CROSSING WITH
ANOTHER TRANSMISSION LINE.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 48 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-0900-00
SINGLE CONDUCTOR TENSION ASSEMBLY SCT
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR ALL TYPES OF TENSION/ANGLE AND TERMINAL
/DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 49 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1000-00
SINGLE CONDUCTOR DOUBLE TENSION ASSEMBLY SCDT
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TENSION /TERMINAL/DEADEND TOWERS FOR CROSSING
OF MAJOR HIGHWAYS/EXPRESSWAYS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 50 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1100-00
SINGLE CONDUCTOR SUSPENSION ASSEMBLY SCS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 51 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1200-00
SINGLE CONDUCTOR JUMPER SUSPENSION ASSEMBLY SCJS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 52 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1300-00
SINGLE CONDUCTOR DOUBLE SUSPENSION ASSEMBLY SCDS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES AND ON SMALL RUNNING
ANGLE TYPE SUSPENSION STRUCTURES WHEN THERE IS AN OVERHEAD LINE CROSSING WITH
ANOTHER TRANSMISSION LINE.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 53 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1400-00
SINGLE CONDUCTOR TENSION ASSEMBLY SCT
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR ALL TYPES OF TENSION/ANGLE AND TERMINAL/
DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 54 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1500-00
SINGLE CONDUCTOR DOUBLE TENSION ASSEMBLY SCDT
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TENSION/TERMINAL/DEADEND TOWERS FOR CROSSING
OF MAJOR HIGHWAYS/EXPRESSWAYS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 55 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1600-00
TWIN BUNDLE CONDUCTOR SUSPENSION ASSEMBLY CS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES.
3.
FOR 230kV TRANSMISSION LINES THE ARCING HORN SHOWN FOR LINE SIDE SHALL BE
RACKET/RING TYPE DESIGN.
4.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES)
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 56 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1700-00
TWIN BUNDLE CONDUCTOR SUSPENSION ASSEMBLY CS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON SMALL RUNNING ANGLE TYPE SUSPENSION STRUCTURES
FOR 69kV TO 230kV TRANSMISSION LINES WHEN LINE ANGLE IS UP TO 10O.
3.
FOR 230kV TRANSMISSION LINES THE ARCING HORN SHOWN FOR LINE SIDE SHALL BE
RACKET/RING TYPE DESIGN.
4.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 57 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1800-00
TWIN BUNDLE CONDUCTOR JUMPER SUSPENSION ASSEMBLY JS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS.
3.
FOR 230kV TRANSMISSION LINES THE ARCING HORN SHOWN FOR LINE SIDE SHALL BE
RACKET/RING TYPE DESIGN.
4.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 58 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-1900-00
TWIN BUNDLE CONDUCTOR DOUBLE SUSPENSION ASSEMBLY CDS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES AND ON SMALL ANGLE
SUSPENSION TYPE STRUCTURES WHEN THERE IS AN OVERHEAD LINE CROSSING WITH
ANOTHER TRANSMISSION LINE.
3.
FOR 230kV TRANSMISSION LINES THE ARCING HORN SHOWN FOR LINE SIDE SHALL BE
RACKET/RING TYPE DESIGN.
4.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 59 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2000-00
TWIN BUNDLE CONDUCTOR TENSION ASSEMBLY CT (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR ALL TYPES OF TENSION/ANGLE AND TERMINAL/
DEADEND TOWERS.
3.
FOR 230kV TRANSMISSION LINES THE ARCING HORN SHOWN FOR LINE SIDE SHALL BE
RACKET/RING TYPE DESIGN.
4.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 60 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2100-00
TWIN BUNDLE CONDUCTOR SLACK TENSION ASSEMBLY CST (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY IS INTENDED TO BE USED FOR DEADEND SLACK SPAN.
3.
FOR 230kV TRANSMISSION LINES THE ARCING HORN SHOWN FOR LINE SIDE SHALL BE
RACKET/RING TYPE DESIGN
4.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 61 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2200-00
TWIN BUNDLE CONDUCTOR SUSPENSION ASSEMBLY CS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 62 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2300-00
TWIN BUNDLE CONDUCTOR JUMPER SUSPENSION ASSEMBLY JS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 63 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2400-00
TWIN BUNDLE CONDUCTOR DOUBLE SUSPENSION ASSEMBLY CDS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO LIST OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES AND ON SMALL ANGLE
SUSPENSION TYPE STRUCTURES WHEN THERE IS AN OVERHEAD LINE CROSSING WITH
ANOTHER TRANSMISSION LINE.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 64 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2500-00
TWIN BUNDLE CONDUCTOR TENSION ASSEMBLY CT (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR ALL TYPES OF TENSION/ANGLE AND TERMINAL/
DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 65 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2600-00
TWIN BUNDLE CONDUCTOR SLACK TENSION ASSEMBLY CST (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY IS INTENDED TO BE USED FOR DEADEND SLACK SPAN.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 66 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2700-00
TWIN BUNDLE CONDUCTOR SUSPENSION ASSEMBLY CS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 67 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2800-00
TWIN BUNDLE CONDUCTOR JUMPER SUSPENSION ASSEMBLY JS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO LIST OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 68 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-2900-00
TWIN BUNDLE CONDUCTOR DOUBLE SUSPENSION ASSEMBLY CDS (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE STRUCTURES AND ON SMALL ANGLE
SUSPENSION TYPE STRUCTURES WHEN THERE IS AN OVERHEAD LINE CROSSING WITH
ANOTHER TRANSMISSION LINE.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 69 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-3000-00
TWIN BUNDLE CONDUCTOR TENSION ASSEMBLY CT (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR ALL TYPES OF TENSION/ANGLE AND TERMINAL/
DEADEND TOWERS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 70 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-3100-00
TWIN BUNDLE CONDUCTOR SLACK TENSION ASSEMBLY CST (2)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY IS INTENDED TO BE USED FOR DEADEND SLACK SPAN.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
4.
CONTROL CORONA RING TO BE USED FOR THE ENERGIZED END ONCE TRANSMISSION LINES
OPERATED AT 110kV AND ABOVE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 71 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-3200-00
QUAD BUNDLE CONDUCTOR VEE SUSPENSION ASSEMBLY VS (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT SUSPENSION TOWERS FOR 380kV
TRANSMISSION LINES CONSTRUCTED WITH SQUARE ORIENTATION.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 72 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-3300-00
QUAD BUNDLE CONDUCTOR VEE SUSPENSION ASSEMBLY VS (4)
(DIAMOND ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT SUSPENSION TOWERS FOR 380kV
TRANSMISSION LINES CONSTRUCTED WITH DIAMOND ORIENTATION.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 73 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-3400-00
QUAD BUNDLE CONDUCTOR VERTICAL SUSPENSION ASSEMBLY IS (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT SUSPENSION TOWERS FOR 380kV
TRANSMISSION LINES CONSTRUCTED WITH SQUARE ORIENTATION.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 74 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-3500-00
QUAD BUNDLE CONDUCTOR VERTICAL DOUBLE SUSPENSION ASSEMBLY IDS (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO LIST OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT TYPE SUSPENSION TOWERS FOR 380kV
TRANSMISSION LINES CROSSING WITH ROADS (OTHER THAN MAJOR HIGHWAYS).
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 75 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-3600-00
QUAD BUNDLE CONDUCTOR VEE JUMPER SUSPENSION ASSEMBLY VJ (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS FOR 380kV TRANSMISSION LINES.
3.
THIS ASSEMBLY SHALL ALSO BE USED FOR THE CENTRE PHASE ON 380kV SINGLE CIRCUIT
TOWERS TO BE USED FOR SERIES COMPENSATION AND LINE TRANSPOSITION.
4.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 76 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-3700-00
QUAD BUNDLE CONDUCTOR VEE JUMPER SUSPENSION ASSEMBLY VJG (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON GANTRY STRUCTURES FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 77 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-3800-00
QUAD BUNDLE CONDUCTOR VERTICAL JUMPER SUSPENSION ASSEMBLY IJ (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS FOR 380kV TRANSMISSION LINES. BOX
TYPE CROSS-ARM SHALL REQUIRE TWO JUMPER ASSEMBLIES ONE AT EACH END OF THE BOX.
WHEN LINE ANGLE IS 60O OR MORE.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 78 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-3900-00
QUAD BUNDLE CONDUCTOR TENSION ASSEMBLY CT2 (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON ALL TYPES OF ANGLE STRAIN TOWERS AND DEADEND
TOWERS FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 79 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-4000-00
QUAD BUNDLE CONDUCTOR TENSION ASSEMBLY CT2 (4)
(DIAMOND ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS)
2.
THIS ASSEMBLY SHALL BE USED ON ALL TYPES OF ANGLE STRAIN TOWERS AND DEADEND
TOWERS FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES)
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 80 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-4100-00
QUAD BUNDLE CONDUCTOR SLACK TENSION ASSEMBLY CST2 (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED IN GANTRY SPAN ON DEADEND TYPE (TERMINALS) TOWERS
AND GANTRY STRUCTURE FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 81 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-4200-00
QUAD BUNDLE CONDUCTOR SLACK TENSION ASSEMBLY CST2 (4)
(DIAMOND ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED IN GANTRY SPAN ON DEADEND TYPE (TERMINAL) TOWERS
AND GANTRY STRUCTURE FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 82 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-4300-00
QUAD BUNDLE CONDUCTOR TENSION ASSEMBLY CT4 (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON ALL TYPES OF ANGLE STRAIN TOWERS AND DEADEND
TOWERS FOR 380kV TRANSMISSION LINES WHEN INDICATED IN SOW/TS.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL PORCELAIN/GLASS FOG TYPE OR
AEROFORM, AS SPECIFIED IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 83 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-4400-00
QUAD BUNDLE CONDUCTOR VEE SUSPENSION ASSEMBLY VS (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT SUSPENSION TOWERS FOR 380kV
TRANSMISSION LINES CONSTRUCTED WITH SQUARE ORIENTATION.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 84 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-4500-00
QUAD BUNDLE CONDUCTOR VEE JUMPER SUSPENSION ASSEMBLY VJ (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 85 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-4600-00
QUAD BUNDLE CONDUCTOR VEE JUMPER SUSPENSION ASSEMBLY VJG (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON GANTRY STRUCTURES FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 86 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-4700-00
QUAD BUNDLE CONDUCTOR VERTICAL JUMPER SUSPENSION ASSEMBLY IJ (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS FOR 380kV TRANSMISSION LINES. BOX
TYPE CROSS-ARM SHALL REQUIRE TWO JUMPER ASSEMBLIES ONE AT EACH END OF THE BOX
WHEN LINE ANGLE IS 60O OR MORE.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 87 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-4800-00
QUAD BUNDLE CONDUCTOR TENSION ASSEMBLY CT2 (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (SEE BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON ALL TYPES OF ANGLE STRAIN TOWERS AND DEADEND
TOWERS FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 88 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-4900-00
QUAD BUNDLE CONDUCTOR SLACK TENSION ASSEMBLY CST2 (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (SEE BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED IN GANTRY SPAN ON DEADEND TYPE (TERMINALS) TOWERS
AND GANTRY STRUCTURE FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL LONG ROD PORCELAIN AS SPECIFIED
IN THE RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 89 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-5000-00
QUAD BUNDLE CONDUCTOR VEE SUSPENSION ASSEMBLY VS (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT SUSPENSION TOWERS FOR 380kV
TRANSMISSION LINES CONSTRUCTED WITH SQUARE ORIENTATION.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 90 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-5100-00
QUAD BUNDLE CONDUCTOR VEE SUSPENSION ASSEMBLY VS (4)
(DIAMOND ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON TANGENT SUSPENSION TOWERS FOR 380kV
TRANSMISSION LINES CONSTRUCTED WITH DIAMOND ORIENTATION.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 91 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-5200-00
QUAD BUNDLE CONDUCTOR VEE JUMPER SUSPENSION ASSEMBLY VJ (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED FOR INNER AND OUTER JUMPER LOOPS FOR ALL TYPES OF
TENSION/ANGLE AND TERMINAL/DEADEND TOWERS FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 92 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-5300-00
QUAD BUNDLE CONDUCTOR VEE JUMPER SUSPENSION ASSEMBLY VJG (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON GANTRY STRUCTURES FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 93 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-5400-00
QUAD BUNDLE CONDUCTOR TENSION ASSEMBLY CT4 (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (SEE BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON ALL TYPES OF ANGLE STRAIN TOWERS AND DEADEND
TOWERS FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 94 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-5500-00
QUAD BUNDLE CONDUCTOR TENSION ASSEMBLY CT4 (4)
(DIAMOND ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (SEE BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED ON ALL TYPES OF ANGLE STRAIN TOWERS AND DEADEND
TOWERS FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 95 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-5600-00
QUAD BUNDLE CONDUCTOR SLACK TENSION ASSEMBLY CST2 (4)
(SQUARE ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (SEE BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED IN GANTRY SPAN ON DEADEND TYPE (TERMINALS) TOWERS
AND GANTRY STRUCTURE FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 96 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
ORIENTATION OF
JUMPER TERMINALS
FIGURE TC-2221-5700-00
QUAD BUNDLE CONDUCTOR SLACK TENSION ASSEMBLY CST2 (4)
(DIAMOND ORIENTATION)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (SEE BILL OF MATERIALS).
2.
THIS ASSEMBLY SHALL BE USED IN GANTRY SPAN ON DEADEND TYPE (TERMINALS) TOWERS
AND GANTRY TOWERS FOR 380kV TRANSMISSION LINES.
3.
THE INSULATORS SHOWN IN THE FIGURE ARE TYPICAL COMPOSITE AS SPECIFIED IN THE
RELEVANT ENGINEERING STANDARD (TES).
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 97 OF 138
TRANSMISSION CONSTRUCTION STANDARD
4.2
TCSP12221R01/MAT
TCS-P-122.21, Rev. 01
SHIELDWIRE (OPGW/OGW) FITTINGS
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 98 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-5800-00
OPTICAL FIBER (OPGW) SHIELDWIRE SUSPENSION ASSEMBLY OPS
FIGURE TC-2221-5900-00
OPTICAL FIBER (OPGW) SHIELDWIRE TENSION ASSEMBLY (SPLICING) OPT (S)
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 99 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-6000-00
OPTICAL FIBER (OPGW) SHIELDWIRE TENSION ASSEMBLY (NON-SPLICING) OPT (NS)
FIGURE TC-2221- 6100-00
VIBRATION DAMPER OPTICAL FIBER (OPGW)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
OPS ASSEMBLY SHALL BE USED ON TANGENT SUSPENSION TOWERS AND SIMILARLY OPT (S)
/ OPT (NS) ASSEMBLY TO BE USED FOR SPLICING AND NON SPLICING PURPOSE RESPECTIVELY.
3.
OPS ASSEMBLY SHALL BE WITH TWO LINKS AS PER ABOVE DRAWING. THE ASSEMBLY SHALL
BE ABLE TO ARTICULATE IN BOTH DIRECTIONS; TRANSVERSE & LONGITUDINAL AND THERE
SHALL BE SUFFICIENT CLEARANCE FROM THE STRUCTURE TO AVOID ANY OBSTRUCTION
WITH THE METAL PARTS.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 100 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-6200-00
SHIELD WIRE (OGW) SUSPENSION ASSEMBLY SS
FIGURE TC-2221-6300-00
SHIELD WIRE (OGW) TENSION ASSEMBLY ST
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 101 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
.
FIGURE TC-2221- 6400-00
VIBRATION DAMPER FOR SHIELD WIRE (OGW)
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
SS ASSEMBLY SHALL BE USED ON TANGENT SUSPENSION TOWERS AND ST ASSEMBLY TO BE
USED FOR ALL TYPE OF ANGLE STRAIN / DEAD END TOWERS.
3.
VIBRATION DAMPER SHALL BE USED AS PER APPROVED DAMPING STUDY IN ACCORDANCE
WITH MANUFACTURER’S RECOMMENDATIONS.
4.
SS ASSEMBLY SHALL BE WITH TWO LINKS AS PER ABOVE DRAWING. THE ASSEMBLY SHALL
BE ABLE TO ARTICULATE IN BOTH DIRECTIONS; TRANSVERSE AND LONGITUDINAL AND
THERE SHALL BE SUFFICIENT CLEARANCE FROM THE STRUCTURE TO AVOID ANY
OBSTRUCTION WITH THE METAL PARTS.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 102 OF 138
TRANSMISSION CONSTRUCTION STANDARD
4.3
TCSP12221R01/MAT
TCS-P-122.21, Rev. 01
CONDUCTOR FITTINGS
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 103 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
.
FIGURE TC-2221-6500-00
FULL TENSION SPLICE / COMPRESSION MID SPAN JOINT
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
ALL SPLICES SHALL BE MADE 15 METEERS AWAY FROM STRUCTURES AND NO SPLICE SHALL
BE MADE IN DEADEND SPAN.
3.
AS A RULE NOT MORE THAN ONE JOINT OR SPLICE SHALL BE MADE IN ANY ONE CONDUCTOR
IN ANY ONE SPAN.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 104 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-6600-00
COMPRESSION REPAIR SLEEVE
NOTE:
1.
REPAIR SLEEVE SHALL BE USED ON SLIGHTLY DAMAGED STRANDS OF PHASE CONDUCTORS.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 105 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-6700-00
TYPICAL QUAD BUNDLE SPACER DAMPERS
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
QUAD BUNDLE SPACER DAMPERS WITH SQUARE ORIENTATION SHALL BE USED ON 380kV
TRANSMISSION LINES FOR IN-SPAN POSITIONING AS WELL AS ON THE JUMPER LOOPS.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 106 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-6800-00
TWIN CONDUCTOR BUNDLE SPACER DAMPER
NOTE:
1.
TWIN BUNDLE SPACER DAMPERS WITH HORIZONTAL ORIENTATION SHALL BE USED ON
132kV-230kV TRANSMISSION LINES FOR IN-SPAN POSITIONING AS WELL AS ON THE JUMPER
LOOPS.
2.
THE DAMPING SYSTEM FOR TWIN BUNDLE CONDUCTORS SHALL COMPRISE SPACER DAMPER
AND VIBRATION DAMPER AT BOTH SPAN EXTREMITIES.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 107 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221- 6900-00
VIBRATION DAMPER FOR CONDUCTOR
NOTE:
1.
NUMBER IN A CIRCLE INDICATES DRAWING CODE (REFER TO BILL OF MATERIALS).
2.
VIBRATION DAMPERS SHALL BE USED ON ALL SINGLE CONDUCTOR TRANSMISSION LINES
(69kV-132kV) TO CONTROL AEOLIAN VIBRATION.
3.
VIBRATION DAMPER BOLTS SHALL ALWAYS BE WITH THEIR HEADS FACING TOWARDS
GROUND.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 108 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TYPE
TCS-P-122.21, Rev. 01
POSITION
TYPE
-
ALUM. CLAD STEEL WIRE
CENTER WRIE
01 X 3.081 mm.
-
ALUM. CLAD STEEL WIRE
FIRST LAYER
06 X 3.081 mm.
-
ALUMINIUM WIRE
SECOND LAYER
12 X 3.081 mm.
-
ALUMINIUM WIRE
THIRD LAYER
18 X 3.081 mm.
-
ALUMINIUM WIRE
FOURTH LAYER
24 X 3.081 mm.
FIGURE TC-2221- 7000-00
ACSR/AW CONDOR CONDUCTOR (CROSS SECTION DRAWING)
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 109 OF 138
TRANSMISSION CONSTRUCTION STANDARD
5.0
TCSP12221R01/MAT
TCS-P-122.21, Rev. 01
STRUCTURE GROUNDING DETAILS
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 110 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-7100-00
LATTICE STEEL TOWER GROUNDING INSTALLATION
NOTE:
1.
REINFORCING BARS OF EACH FOOTING SHALL BE BONDED WITH THE CORRESPONDING STUB
ANGLE AT ATLEAST TWO POINTS.
2.
THE SIZE OF GROUNDING CONDUCTOR SHALL BE AS PER TES-P-122.10.
3.
LATTICED STEEL STRUCTURES SHALL BE GROUNDED ON ITS TWO OPPOSITE LEGS BY MEANS
OF COUNTERPOISE AND TWO THERMIT COUPLED GROUND RODS EXTENDED OUTWARD AT
180O OR IN LINE WITH TWO OPPOSITE LEGS.
4.
ALL BENDS IN THE GROUNDING CONDUCTOR SHALL HAVE A BENDING RADIUS EQUAL TO OR
GREATER THAN 75 mm.
5.
THE COUNTERPOISE SHALL BE PARALLEL TO THE TRANSMISSION LINE.
6.
WHEN A CONTINUOUS COUNTERPOISE IS REQUIRED AT A PARTICULAR TOWER SITE AND
EITHER OR BOTH OF THE ADJACENT SITES ARE PROTECTED BY GROUND RODS, THE GROUND
WIRE SHALL BE TERMINATED AT THESE SITES BY A GT TYPE CONNECTION PER DETAIL 3.
7.
COUNTERPOISE SHALL BE BURRIED 500 mm BELOW GRADE. WHEN ROCK SURFACES ARE
ENCOUNTERED, ROCK SHALL BE CUT 150 mm DEEP. THE COUNTERPOSIE SHALL BE LAID IN
THE TRENCH AND THE TRENCH SHALL THEN BE FILLED WITH CONCRETE.
8.
COUNTERPOISE SHALL BE BURRIED TO A MINIMUM DEPTH OF 1800 mm IN DUNE AREAS WHEN
THE POTENTIAL EXISTS FOR THE COUNTERPOISE TO BECOME EXPOSED DUE TO SHIFTING
SAND.
9.
SPACERS SHALL BE USED TO AVOID ANY CONTACT BETWEEN THE REINFORCEMENT BARS
AND THE GROUNDING CONDUCTOR.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 111 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-7200-00
GROUNDING CONNECTIONS DETAILS
Legend for Grounding Connections:
GT: Through Cable to Ground Rod
GB: Ground Rod Splice
TCSP12221R01/MAT
GR: Single Cable to Top of Ground Rod
SS: Horizontal Cable-to-Cable Splice
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 112 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-7300-00
GROUNDING CONNECTIONS DETAILS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 113 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-7400-00
PROCEDURE FOR ADDITIONAL TOWER GROUNDING
NOTE:
1.
FOR 230kV AND 380kV TRANSMISSION LINES STRUCTURE FOOTING RESISTANCE SHALL BE 3
OHMS OR LESS WITHIN 3km OF SUBSTATIONS AND 10 OHMS OR LESS ELSEWHERE. HOWEVER,
FOR 69kV, 110kV, 115kV AND 132kV TRANSMISSION LINES THE REQUIRED RESISTANCE MAY BE
10 OHMS OR LESS WITHIN 1.6KM OF SUSBSTATIONS AND 20 OHMS OR LESS ELSEWHERE.
MEASUREMENTS SHALL BE MADE AFTER BACKFILL UNDER NORMAL SOIL CONDITION AND
BEFORE GROUND IS CONNECTED TO STUB ANGLE.
2.
BOND ALL FOUR STUB ANGLES AS SHOWN IN STEP 1 AND FOLLOW THE PROCEDURE AS
SHOWN IN STEP 2, THEN MAKE TOWER FOOTING MEASUREMENT. IF THE REQUIREMENTS OF
PROCEDURE 1 ARE OBTAINED THEN NO OTHER STEPS NEED TO BE TAKEN.
3.
IF THE REQUIREMENTS OF PROCEDURE 1 ARE NOT OBTAINED AFTER DOING STEP 2, FOLLOW
THE PROCEDURE SHOWN IN STEPS 3 TO 5 UNTIL THE REQUIREMENTS OF PROCEDURE 1 ARE
OBTAINED, MAKING A RESISTANCE MEASUREMENT AFTER EACH STEP.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 114 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-7500-00
PROCEDURE FOR ADDITIONAL TOWER GROUNDING
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 115 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-7600-00
PROCEDURE FOR ADDITIONAL TOWER GROUNDING
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 116 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-7700-00
STEEL MONOPOLE GROUNDING INSTALLATION
1.
ANCHOR BOLTS (TWO BOLTS) SHALL BE CONNECTED WITH THE REINFORCEMENT OF
CONCRETE FOOTING.
2.
SIZE OF GROUNDING SHALL BE PER TES-P-122.10
3.
MONOPOLE STEEL STRUCTURES SHALL BE GROUNDED BY MEANS OF TWO COUNTERPOISE
AND TWO THERMITE COUPLED GROUND RODS, INSTALLED 8 METERS AWAY FROM THE
FOUNDATION IN OPPOSITE DIRECTION WITH EACH OTHER.
4.
ALL BENDS IN CONDUCTOR SHALL HAVE A BENDING RADIUS EQUAL TO OR GREATER THAN
75 MM.
5.
WHEN COMTINUOUS COUNTERPOISE IS REQUIRED AT A PARTICULAR MONOPOLE SITE AND
EITHER OR BOTH OF THE ADJACENT SITES ARE PROTECTED BY GROUNDIN RODS, THE
GROUND WIRE SHALL BE TERMINATED AT THESE SITES BY A GT TYPE CONNECTION PER
DETAIL 3.
6.
COUNTERPOISE SHALL BE BURIED 500mm BELOW GRADE. WHEN ROCK IS ENCOUNTERED,
ROCK SHALL BE CUT 150mm DEEP. THE CONUTERPOISE SHALL BE LAID IN THE TRENCH AND
THE TRENCH SHALL THEN BE FILLED WITH CONCRETE.
7.
COUNTERPOISE SHALL BE BURIED TO A MAXIMUM DEPTH OF 1800mm IN DUNE AREAS WHERE
THE POTENTIAL EXISTS FOR THE COUNTERPOISE TO BECOME EXPOSED DUE TO SHIFTING
SAND.
8.
THE COUNTERPOISE SHALL BE PARALLEL TO THE TRANSMISSION LINE.
9.
SPACERS SHALL BE USED TO AVOID ANY CONTACT BETWEEN THE REINFORCEMENT BARS
AND THE GROUNDING CONDUCTOR.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 117 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-7800-00
PROCEDURE FOR ADDITIONAL MONOPOLE GROUNDING
NOTE:
1.
FOR 230kV AND 380kV TRANSMISSION LINES STRUCTURE FOOTING RESISTANCE SHALL BE 3
OHMS OR LESS WITHIN 3km OF SUBSTATIONS AND 10 OHMS OR LESS ELSEWHERE. HOWEVER,
FOR 69kV, 110kV, 115kV AND 132kV TRANSMISSION LINES THE REQUIRED RESISTANCE MAY BE
10 OHMS OR LESS WITHIN 1.6KM OF SUSBSTATIONS AND 20 OHMS OR LESS ELSEWHERE.
MEASUREMENTS SHALL BE MADE AFTER BACKFILL UNDER NORMAL SOIL CONDITION AND
BEFORE GROUND IS CONNECTED TO STEEL MONOPOLE.
2.
BOND TWO ANCHOR BOLTS AS SHOWN IN STEP 1 AND FOLLOW THE PROCEDURE AS SHOWN
IN STEP 2, THEN MAKE MONOPOLE FOOTING RESISTANCE MEASUREMENT. IF THE
REQUIREMENTS OF PROCEDURE 1 ARE OBTAINED THEN NO OTHER STEPS NEED TO BE TAKEN.
3.
IF THE REQUIREMENTS OF PROCEDURE 1 ARE NOT OBTAINED AFTER DOING STEP 2, FOLLOW
THE PROCEDURE SHOWN IN STEPS 3 TO 5 UNTIL THE REQUIREMENTS OF PROCEDURE 1 ARE
OBTAINED, MAKING A RESISTANCE MEASUREMENT AFTER EACH STEP.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 118 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-7900-00
PROCEDURE FOR ADDITIONAL MONOPOLE GROUNDING
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 119 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8000-00
PROCEDURE FOR ADDITIONAL MONOPOLE GROUNDING
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 120 OF 138
TRANSMISSION CONSTRUCTION STANDARD
6.0
TCSP12221R01/MAT
TCS-P-122.21, Rev. 01
STRUCTURE FOUNDATION DETAILS
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 121 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8100-00
FOUNDATION LAYOUT PLAN
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 122 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8200-00
PIER TYPE FOUNDATION
NOTE:
1
THE POLYURETHANE COATING AND COAL TAR EPOXY COATING SHALL BE APPLIED PER
TCS-P-122.05.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 123 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8300-00
SPREAD FOOTING TYPE FOUNDATION
NOTE:
1
CONRETE BONDING AGENT SHALL BE APPLIED AT THE TWO WAY CONSTRUCTION JOINT.
2
THE PEDESTAL OF THE FOOTING SHALL BE BATTERED ALONG THE TOWER LEG SLOPE.
3
THE POLYURETHANE COATING AND COAL TAR EPOXY COATING SHALL BE APPLIED PER
TCS-P-122.05.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 124 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8400-00
ROCK PIER TYPE FOUNDATION
NOTE:
1
THE POLYURETHANE COATING AND COAL TAR EPOXY COATING SHALL BE APPLIED PER
TCS-P-122.05.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 125 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8500-00
ROCK ANCHOR TYPE FOUNDATION
NOTE:
1
THE POLYURETHANE COATING AND COAL TAR EPOXY COATING SHALL BE APPLIED PER
TCS-P-122.05.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 126 OF 138
TRANSMISSION CONSTRUCTION STANDARD
7.0
TCS-P-122.21, Rev. 01
STRUCTURE, PHASE IDENTIFICATION AND DANGER SIGN PLATE DETAILS
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 127 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8600-00
LATTICED TOWER IDENTIFICATION FOR AERIAL INSPECTION
SUSPENSION AND SMALL ANGLE TOWERS
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS, REFER BILL OF MATERIAL.
2.
THE AERIAL LINE IDENTIFICATION PLATES SHALL BE INSTALLED ON EVERY TENTH
STRUCTURE, THE FIRST STRUCTURE, THE LAST STRUCTURE, AND ON BOTH STRUCTURES
ADJACENT TO A HIGHWAY CROSSING, A RAIL ROAD CROSSING AND AN ACCESS ROAD
CROSSING.
3
TOWER TAGS SHALL BE INSTALLED ON THE TRANSVERSE FACE READABLE IN THE DIRECTION
OF INCREASING STATION NUMBERS.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 128 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8700-00
LATTICED TOWER IDENTIFICATION FOR AERIAL INSPECTION
MEDIUM AND HEAVY ANGLE TOWERS
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS, REFER BILL OF MATERIAL.
2.
THE AERIAL LINE IDENTIFICATION PLATES SHALL BE INSTALLED ON EVERY TENTH
STRUCTURE, THE FIRST STRUCTURE, THE LAST STRUCTURE, AND ON BOTH STRUCTURES
ADJACENT TO A HIGHWAY CROSSING, A RAIL ROAD CROSSING AND AN ACCESS ROAD
CROSSING.
3
TOWER TAGS SHALL BE INSTALLED ON THE TRANSVERSE FACE READABLE IN THE DIRECTION
OF INCREASING STATION NUMBERS.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 129 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8800-00
TOWER IDENTIFICATION FOR GROUND INSPECTION
ALL TOWER TYPES
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS, REFER BILL OF MATERIAL.
2.
ALL BOLT HOLE DIAMTERS SHALL BE 2MM LARGER THAN THE BOLT DIA.
3
ALL NEW CUTS AND DRILLED HOLES IN GALVANIZED METAL SHALL BE TREATED WITH RUST
INHIBITING COMPOUND BEFORE ASSEMBLING.
4
TOWER TAGS SHALL BE INSTALLED ON THE TRANSVERSE FACE READABLE IN THE DIRECTION
OF INCREASING STATION NUMBERS.
5
TOWER IDENTIFICATION TAGS FOR GROUND INSPECTION SHALL BE INSTALLED ON THE
TOWER LEG WITHOUT STEP BOLT.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 130 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-8900-00
STEEL MONOPOLE IDENTIFICATION DETAILS
FOR AERIAL AND GROUND INSPECTION (ALL TYPES)
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS, REFER BILL OF MATERIAL.
2
ALL NEW CUTS AND DRILLED HOLES IN GALVANIZED METAL SHALL BE TREATED WITH RUST
INHIBITING COMPOUND BEFORE ASSEMBLING.
3
STEEL MONOPOLE TAGS SHALL BE INSTALLED ON THE TRANSVERSE FACE READABLE IN THE
DIRECTION OF INCREASING STATION NUMBERS.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 131 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-9000-00
PHASE IDENTIFICATION PLATES DETAILS
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS. REFER BILL OF MATERIAL.
2
ALL NEW CUTS AND DRILLED HOLES IN GALVANIZED METAL SHALL BE TREATED WITH RUST
INHIBITING COMPOUND BEFORE ASSEMBLING.
3
PHASE IDENTIFICATION PLATES SHALL BE INSTALLED ON THE TRANSVERSE FACE READABLE
IN THE DIRECTION OF INCREASING STATION NUMBERS.
4
THE FLAT BAR SHALL BE FIXED WITH M14 GALVANIZED BOLT, NUT AND WASHER.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 132 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-9100-00
DANGER SIGN PLATE DETAILS
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS, REFER BILL OF MATERIAL.
2
THE PLATE SHALL BE FITTED WITH M14 BOLTS OF STAINLESS STEEL MATERIAL.
3
LETTERS AND SYMBOLS SHALL BE SCALED IN PROPORTION TO OVERALL PLATE DIMENSIONS.
4
CORNERS OF SIGNS SHALL BE ROUNDED AND EDGES SHALL BE SMOOTHED SO AS TO AVOID
INJURY.
5
DANGER PLATE SHALL BE INSTALLED ON EVERY TOWER.
6
THE SIGN PLATE SHALL BE MADE OF 2MM THICK ALUMINUM ALLOY PLATE OR STAINLESS
STEEL SHEET.
7
HIGH GLOSS ENAMEL PAINT REQUIREMENTS SHALL CONFORM TO 78-TMSS-4, 78-TMSS-03 AND
ENGINEERING STANDARD TES-H.107.01.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 133 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-9200-00
DANGER SIGN PLATE INSTALLATION
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS, REFER BILL OF MATERIAL.
2
DANGER SIGN PLATE TO BE MOUNTED ON BOTH TRANSVERSE TOWER FACES ON LEGS WITH
STEP BOLTS.
3
DANGER SIGN PLATES SHALL BE INSTALLED ON EVERY STRUCTURE, ABOVE THE STRUCTURE
IDENTIFICATION PLATES, WITHOUT CLIMBING BARRIERS.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 134 OF 138
TRANSMISSION CONSTRUCTION STANDARD
8.0
TCSP12221R01/MAT
TCS-P-122.21, Rev. 01
STRUCTURE ANTI-CLIMBING GUARD DETAILS
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 135 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-9300-00
ANTI CLIMBING GUARD FOR STEEL TOWERS
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS, REFER BILL OF MATERIAL
2
FOR INSTALLATION AND FABRICATION DETAILS, SEE FIGURE FIGURE TC-2221-9400-00
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 136 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-9400-00
ANTI CLIMBING GUARD INSTALLATION AND FABRICATION DETAILS
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS.
2
ALL NEW CUTS AND DRILLED HOLES IN GALVANIZED METAL SHALL BE TREATED WITH RUST
INHIBITING COMPOUND BEFORE ASSEMBLING.
3
FABRICATE STEEL FASTENER FROM 90 X 27 X 6 MM ANGLE BAR.
4
LENGTH OF BARBED WIRE VARIES IN ACCORDANCE WITH TOWER TYPE AND HEIGHT.
5
INSTALL ANTI CLIMBING GUARD TO TRANSMISSION TOWER FOUR (4) METER ABOVE GROUND
SURFACE.
6
THE GATE SHALL OPEN UPWARDS AND ITS MOVEMENT SHALL BE IN THE RANGE OF 1200 TO
1400.
7
APPROPRIATE ‘L’ KEYS SHALL BE SUPPLIED. THE DIMENSIONS OF GATE SHALL BE FINALIZED
AFTER INSTALLATION OF A SAMPLE ON THE TOWER IN THE FIELD.
8
THE GATE SHALL BE INSTALLED ON THE TOWER LEG WITH STEP BOLTS.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 137 OF 138
TRANSMISSION CONSTRUCTION STANDARD
TCS-P-122.21, Rev. 01
FIGURE TC-2221-9500-00
ANTI CLIMBING GUARD FOR STEEL MONOPOLE
NOTE:
1.
ALL DIMENSIONS ARE IN MILLIMETERS, REFER BILL OF MATERIAL
2
LENGTH OF BARBED WIRE VARIES IN ACCORDANCE WITH THE TYPE OF POLE.
3
INSTALL ANTI CLIMBING GUARD ON STEEL POLE FOUR (4) METER ABOVE GROUND SURFACE.
TCSP12221R01/MAT
Date of Approval: December 29, 2021
License=BUREAU VERITAS SA-KSA BRANCH/SA-11111528-t Not For Resale ,12/23/2024 2:48:48 AM Saudi Time
PAGE 138 OF 138
Thank you for accessing National Grid SA Transmission Standard . You can provide your valuable feedback for same
standard here. Kindly use below given link or scan below given QRCode to open Feedback Form.
https://www.se.com.sa/Rehabilitation-Manufacturers/FeedbackForm.aspx
Download