SD
SD
SD
SD
FE
FE
SD
SD
SD
SD
SD
FE
FE
FACP
MCP
SD
SD
SD
SD
MCP
SD
FE
JUNEL T. PON
PROPOSED LAYOUT PLAN FOR FIRE DETECTION AND ALARM SYSTEM
LOBOC, BOHOL
FDAS LAYOUT
WIRING DIAGRAM
E
1
SD
SD
SD
SD
SD
SD
SD
FE
SD
SD
SD
FE
MCP
SD
SD
MCP
FE
FE
JUNEL T. PON
SD
PROPOSED LAYOUT PLAN FOR FIRE DETECTION AND ALARM SYSTEM
LOBOC, BOHOL
FDAS LAYOUT
WIRING DIAGRAM
E
2
SD
SD
FE
FE
SD
MCP
SD
MCP
SD
FE
JUNEL T. PON
SD
FE
PROPOSED LAYOUT PLAN FOR FIRE DETECTION AND ALARM SYSTEM
LOBOC, BOHOL
FDAS LAYOUT
WIRING DIAGRAM
E
3
SD
FE
SD
SD
SD
SD
FE
MCP
SD
SD
SD
MCP
FE
JUNEL T. PON
FE
PROPOSED LAYOUT PLAN FOR FIRE DETECTION AND ALARM SYSTEM
LOBOC, BOHOL
FDAS LAYOUT
WIRING DIAGRAM
E
4
LEGEND:
GENERAL ELECTRICAL NOTES:
1. EXACT QUANTITIES OF EXISTING DEVICES ARE NOT SHOWN.
2. ALL NEW DEVICES SHALL BE PURCHASED FROM THE BUILDING FIRE
ALARM MAINTENANCE CONTRACTOR TO ENSURE COMPATIBILITY WITH
BUILDING'S FIRE ALARM SYSTEM.
3. REPROGRAMMING OF THE BUILDING FIRE ALARM CONTROL PANEL
SHALL BE DONE BY THE BUILDINGS FIRE ALARM MAINTENANCE
CONTRACTOR.
4. EXISTING BUILDING SYSTEMS ARE NOT SHOWN AND SHALL REMAIN
ACTIVE.
5. OBTAIN PERMISSION FROM THE BUILDING MANAGER PRIOR TO
STARTING OF WORK.
6. PRIOR TO STARTING OF THE FIRE ALARM WORK, THE CONTRACTOR
SHALL CONTACT THE BUILDING FIRE ALARM VENDOR AND THE
BUILDING CHIEF ENGINEER FOR DIRECTIONS.
7. ALL WIRING SHALL BE PER MANUFACTURER'S REQUIREMENT AND
RECOMMENDATION AND MEET APPLICABLE CODE REQUIREMENTS..
8. PROJECT SPECIFIC FIRE ALARM RISER DIAGRAM AND SHOP
DRAWINGS, INCLUDING BATTERY CALCULATIONS AND NOTIFICATION
APPLIANCE CIRCUIT VOLTAGE DROP ANALYSIS PLUS SEQUENCE OF
OPERATIONS, SHALL BE PREPARED AND SUBMITTED, BY THE FIRE
ALARM VENDOR, TO THE PROJECT ENGINEER FOR APPROVAL. ROOM
NAMES AND NUMBERS ON PLANS ARE NOT FOR LABELING OR
PROGRAMMING USE. CONSULT WITH OWNER FOR THIS INFORMATION.
AFTER APPROVAL BY THE ENGINEER, A SUBMITTAL, SIGNED BY A
REGISTERED NICET LEVEL 4, AND ASSOCIATED WITH THE FIRE ALARM
VENDOR, SHALL BE FORWARDED TO THE PROJECT ENGINEER FOR
SUBMITTAL TO THE AUTHORITIES HAVING JURISDICTION
9. ALL FIRE ALARM WIRING SHALL BE TYPE FPLP IN RACEWAY AND SHALL
BE CONCEALED IN WALLS AND CEILINGS SPACES.
10. PLENUM RATED CABLE WITHOUT RACEWAY IS ACCEPTABLE ONLY IN
CONCEALED CEILING SPACES. GALVANIZED EMT (3/4" MIN) SHALL BE
USED FOR ALL RUNS BELOW CEILING. METAL WIREMOLD MAY BE USED
ON CEILINGS WHERE NO ACCESS IS AVAILABLE TO CONCEAL
CABLE-RUN. ALL CONDUITS OR WIREMOLD, WHEN EXPOSED, SHALL BE
PAINTED TO MATCH ADJACENT AREA.
11. ALTERNATE IN ATTIC SPACES. (EXTREME HEAT CONDITIONS) CONTACT
PROJECT ENGINEER FOR RESOLUTION.
12. BE FAMILIAR WITH STRUCTURE PRIOR TO START OF WORK IN ORDER
TO PROVIDE A FIRE ALARM SYSTEM THAT COMPLIES WITH ALL
APPLICABLE CODES, OWNER'S UNDERWRITER REQUIREMENTS, AND
RECOMMENDATIONS OF LOCAL AUTHORITIES HAVING JURISDICTION. IF
CONTRACTOR FAILS TO COMPLY, NO ADDITIONAL COMPENSATION
WILL BE AWARDED FOR WORK THAT IS REASONABLE HAD A
PRE-CONSTRUCTION FIELD SURVEY BEEN COMPLETED.
13. A 100% TOTAL ACCEPTANCE TEST SHALL BE PERFORMED AT THE
COMPLETION OF THE NEW FIRE ALARM SYSTEM INSTALLATION PER
INTERNATIONAL BUILDING CODE (IBC) SEE SPECIFICATIONS FOR
ADDITIONAL REQUIREMENTS
14. ALARM VENDOR SHALL PROVIDE WIRE GUARDS/COVERS ON ALL
PULL-STATIONS, HORN-STROBES, AND DETECTORS LOCATED IN
PUBLIC AREAS SUCH AS, GYMNASIUMS, LOCKER-ROOMS, ETC.
(TYPICAL) LOW PROFILE DETECTORS SHALL BE USED IN ALL
HALLWAYS.
15. FIRE ALARM SPECIFICATIONS SHALL BE USED IN CONJUNCTION WITH
ALL DRAWINGS. ANY DISCREPANCIES SHALL BE BROUGHT TO TO
ATTENTION OF THE ENGINEER FOR RESOLUTION.
16. HEAT DETECTORS IN THE ELEVATOR MACHINE ROOMS AND ELEVATOR
SHAFTS SHALL BE PROGRAMMED TO SIGNAL CONTROL MODULES FOR
ELEVATOR SHUT DOWN VIE A SHUNT TRIP ON THE ELEVATOR FEEDER
PER ASME A17.1
17. PROVIDE DUCT SMOKE DETECTORS IN RETURN DUCTS OF ALL HVAC
SYSTEMS OVER 2000 CFM, OR AS REQUIRED BY INTERNATIONAL
MECHANICAL CODE (IMC). DETECTORS, HOUSINGS, AND SAMPLING
TUBES SHALL BE PROVIDED AND WIRED BY THE ELECTRICAL
CONTRACTOR AND INSTALLED IN THE DUCTWORK BY THE
MECHANICAL CONTRACTOR, UNO.
18. PROVIDE A DEDICATED CONTROL MODULE FOR EACH DETECTOR TO
BE PROGRAMMED
TO SEND A SHUTDOWN SIGNAL TO THE HVAC SYSTEM TO SHUTDOWN
THE FAN, MOTORS, DAMPERS, ETC. ALL LOW VOLTAGE WIRING
BETWEEN THE CONTROL MODULE AND THE HVAC SYSTEM SHALL BE
BY THE ATC CONTRACTOR, UNO.
19. CONTRACTOR SHALL INSTALL ALL ABOVE CEILING DEVICES AFTER ALL
PIPING, DUCTWORK, CONDUITS, ETC ARE INSTALLED SUCH THAT THE
FIRE ALARM DEVICE IS EASILY ACCESSIBLE. COORDINATE LOCATIONS
WITH THE STRUCTURE AND ALL OTHER UTILITIES.
20. PROVIDE A SMALL SCALE FLOORPLAN INCLUDING ROOM
NAMES/NUMBERS, MOUNTED BEHIND A PLEXIGLASS FRAME,
ADJACENT TO THE REMOTE ANNUNCIATOR PANEL.
JUNEL T. PON
AUTOMATIC FIRE
DETECTOR/ CARBON
MONOXIDE DETECTOR
ZONE 7
END OF
THE LINE
- +
MCP
-
+
FIRE ALARM
-
SD
EMERGENCY LIGHT
+
continue
based on
the layout
SD
FIRE EXTINGUISHER
SIXTH FLOOR
EVACUATION AREA
ZONE 6
END OF
THE LINE
- +
MCP
-
+
-
SD
+
continue
based on
the layout
SD
MAIN PANEL BOARD
FIFTH FLOOR
ZONE 5
END OF
THE LINE
- +
MCP
-
+
ESCAPE ROUTE
-
+
SD
SD
FACP
continue
based on
the layout
FOURTH FLOOR
MCP
ADDRESABLE FIRE ALARM
CONTROL PANEL
MANUAL CALL POINT
ZONE 4
END OF
THE LINE
- +
MCP
-
+
-
+
continue
based on
the layout
SD
SD
THIRD FLOOR
ZONE 3
END OF
THE LINE
- +
MCP
-
+
-
SD
+
continue
based on
the layout
SD
SECOND FLOOR
ZONE 2
END OF
THE LINE
- +
MCP
-
+
-
+
SD
SD
continue
based on
the layout
FIRST FLOOR
ZONE 1
END OF
THE LINE
- +
MCP
SD
+
-
+
SD
continue
based on
the layout
BASEMENT
POWER 220V
SOURCE
FIRE ALARM/
BELL
FACP
DC 24V
-
+
-
+
DC 12V DC 12V
BACKUP BATTERY
SUPPLY
RISER DIAGRAM
PROPOSED LAYOUT PLAN FOR FIRE DETECTION AND ALARM SYSTEM
LOBOC, BOHOL
GENERAL NOTES
RISER DIAGRAM
LEGEND
E
5