Piping-classes-exploration-and-production

PETRONAS TECHNICAL STANDARDS DESIGN AND ENGINEERING PRACTICE MANUAL PIPING CLASSES - EXPLORATION AND PRODUCTION PTS 31.38.01.15 January 2010 © 2010 PETROLIAM NASIONAL BERHAD (PETRONAS) All rights reserved. No part of this document may be reproduced, stored in a retrieval system or transmitted in any form or by any means (electronic, mechanical, photocopying, recording or otherwise) without the permission of the copyright owner. PTS 31.38.01.15 January 2010 Page 2 PREFACE PETRONAS Technical Standards (PTS) publications reflect the views, at the time of publication,of PETRONAS OPUs/Divisions. They are based on the experience acquired during the involvement with the design, construction, operation and maintenance of processing units and facilities. Where appropriate they are based on, or reference is made to, national and international standards and codes of practice. The objective is to set the recommended standard for good technical practice to be applied by PETRONAS' OPUs in oil and gas production facilities, refineries, gas processing plants, chemical plants, marketing facilities or any other such facility, and thereby to achieve maximum technical and economic benefit from standardisation. The information set forth in these publications is provided to users for their consideration and decision to implement. This is of particular importance where PTS may not cover every requirement or diversity of condition at each locality. The system of PTS is expected to be sufficiently flexible to allow individual operating units to adapt the information set forth in PTS to their own environment and requirements. When Contractors or Manufacturers/Suppliers use PTS they shall be solely responsible for the quality of work and the attainment of the required design and engineering standards. In particular, for those requirements not specifically covered, it is expected of them to follow those design and engineering practices which will achieve the same level of integrity as reflected in the PTS. If in doubt, the Contractor or Manufacturer/Supplier shall, without detracting from his own responsibility, consult the owner. The right to use PTS rests with three categories of users: 1) 2) 3) PETRONAS and its affiliates. Other parties who are authorised to use PTS subject to appropriate contractual arrangements. Contractors/subcontractors and Manufacturers/Suppliers under a contract with users referred to under 1) and 2) which requires that tenders for projects, materials supplied or - generally - work performed on behalf of the said users comply with the relevant standards. Subject to any particular terms and conditions as may be set forth in specific agreements with users, PETRONAS disclaims any liability of whatsoever nature for any damage (including injury or death) suffered by any company or person whomsoever as a result of or in connection with the use, application or implementation of any PTS, combination of PTS or any part thereof. The benefit of this disclaimer shall inure in all respects to PETRONAS and/or any company affiliated to PETRONAS that may issue PTS or require the use of PTS. Without prejudice to any specific terms in respect of confidentiality under relevant contractual arrangements, PTS shall not, without the prior written consent of PETRONAS, be disclosed by users to any company or person whomsoever and the PTS shall be used exclusively for the purpose they have been provided to the user. They shall be returned after use, including any copies which shall only be made by users with the express prior written consent of PETRONAS. The copyright of PTS vests in PETRONAS. Users shall arrange for PTS to be held in safe custody and PETRONAS may at any time require information satisfactory to PETRONAS in order to ascertain how users implement this requirement. PTS 31.38.01.15 January 2010 Page 3 TABLE OF CONTENTS INTRODUCTION ........................................................................................................... 4 1.1 SCOPE ..................................................................................................................... 4 1.2 DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS .............................................................................................. 4 1.3 DEFINITIONS ......................................................................................................... 4 1.4 CROSS REFERENCES ........................................................................................ 4 1.5 SUMMARY OF CHANGES SINCE THE LAST REVISION ............................. 4 1.5.1 Introduction....................................................................................................... 4 1.5.2 Pressure/temperature rating.......................................................................... 4 1.5.3 Piping classes .................................................................................................. 5 1.5.4 Valves ............................................................................................................... 5 1.5.5 Stud bolts .......................................................................................................... 5 1.5.6 Spectacle blinds/spades ................................................................................ 5 1.5.7 Gaskets ............................................................................................................. 5 1.5.8 Miscellaneous .................................................................................................. 5 1.5.9 Impact testing of austenitic stainless steel .................................................. 6 2. PIPING CLASSES – SERVICES AND MATERIALS SELECTION INDEX ........ 7 3. PIPING CLASSES ........................................................................................................ 8 4. REFERENCES………………………………………………………………………..9 1. APPENDICES APPENDIX A DETAILED CHANGES PER PIPING CLASS………………….10 PTS 31.38.01.15 January 2010 Page 4 1. INTRODUCTION 1.1 SCOPE This PTS contains the piping classes for exploration and production facilities. The basis of design of the piping classes is given in PTS 31.38.01.10 This is a revision of the PTS of the same number dated December 1999; a summary of the changes since the last revision is included in (1.5). The general requirements for piping systems are specified in PTS 31.38.01.11. Excluded from the scope of this PTS are: • oil and gas transmission pipeline systems; • piping classes for refineries and chemical plants, which are included in PTS 31.38.01.12. 1.2 DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS Unless otherwise authorised by PETRONAS, the distribution of this PTS is confined to companies forming part of PETRONAS Group, and to Contractors nominated by them. This PTS is intended for use in exploration and production facilities, within the property limits as defined in ASME B31.3 par. 300.1. If national and/or local regulations exist in which some of the requirements may be more stringent than in this PTS the Contractor shall determine by careful scrutiny which of the requirements are the more stringent and which combination of requirements will be acceptable as regards safety, economic and legal aspects. In all cases the Contractor shall inform the Principal of any deviation from the requirements of this PTS which is considered to be necessary in order to comply with national and/or local regulations. The Principal may then negotiate with the Authorities concerned with the object of obtaining agreement to follow this PTS as closely as possible. 1.3 DEFINITIONS The Contractor is the party which carries out all or part of the design, engineering, procurement, construction, commissioning or management of a project or operation of a facility. The Principal may undertake all or part of the duties of the Contractor. The Principal is the party which initiates, and ultimately pays for, the project. The Principal will generally specify the technical requirements. The Principal may also include an agent or consultant, authorised to act for the Principal. The word shall indicates a requirement. The word should indicates a recommendation. 1.4 CROSS REFERENCES Where cross-references to other parts of this PTS are made, the referenced section number is shown in brackets. Other documents referenced by this PTS are listed in (4). 1.5 SUMMARY OF CHANGES SINCE THE LAST REVISION 1.5.1 Introduction This revision is mainly an update of the existing piping classes to align with the latest developments. The main changes are listed below. An overview of the changes per piping class is given in Appendix A. 1.5.2 Pressure/temperature rating Revisions of ASME B31.3 and ASME B16.5 were issued in January 2004 and November 2003, respectively. The pressure/temperature rating of the piping classes have been recalculated in line with the latest issues of the above codes and standards. PTS 31.38.01.15 January 2010 Page 5 1.5.3 Piping classes Alloy 625, Alloy 825 and 6Mo piping classes with solid and clad material have been developed for the need of recent projects. Piping classes with soft seated ball valves have been replaced due to change from BS 5351 to ISO 17292, which includes a change in pressure/temperature rating. Piping classes with carbon steel galvanised piping are only applicable for fire fighting service and have therefore been removed from this PTS. Piping classes with pipe clamp connectors have not been issued with this revision due to a review on the design verification of the various manufacturer specific clamp connectors. Due to the medium (sodium hypochlorite), titanium piping class 16041 has been subject to fugitive emission tightness class A. 1.5.4 Valves PETRONAS International is working on enhanced group philosophies regarding fugitive emissions on a toxicological and environmental base. This have been applied on the selection of valves and reflect piping classes which are suitable for fugitive emission tightness class A. See PTS 31.38.01.10-Gen, para 3.10. ASTM A216 grade LCB material have been deleted from group piping classes, to be replaced with the now widely available ASTM A216 grade LCC material. This change has allowed higher class ratings for new piping classes. Flanged short pattern triple eccentric butterfly valves have been introduced for DN 200 and larger as an economic alternative for gate valves. Due to a higher performance, these valves have also replaced wafer type butterfly valves class 150 and 300. Dual plate check valves have been introduced for DN 300 and larger sizes, as an economic alternative for swing type check valves. BS 5351 ball valves have been withdrawn and replaced by ISO 17292. Due to a deviation in pressure/temperature rating between both specifications, new piping classes have been developed (see 1.6.3). The maximum temperature of soft seated ball valves have been increased from 120 to 150 °C, which is the maximum allowable temperature for PTFE and Devlon V seats. Ball valves with electroless nickel plated (ENP) balls have been removed from the piping classes and replaced by valves with stainless steel balls. See PTS 39.01.10.11-Gen. 1.5.5 Stud bolts Bolt lengths have been reviewed and verified. 1.5.6 Spectacle blinds/spades Spectacle blinds have been reviewed for ergonomics and limited to the maximum allowable size in accordance with PTS 31.38.01.11-Gen. Spades have been added for all sizes. 1.5.7 Gaskets For pressure classes and sizes up to/incl. DN 600, stainless steel spiral wound graphite gaskets with a stainless steel inner ring and a carbon steel outer ring have been specified. The manufacturing standard for spiral wound gaskets has changed from BS 3381 to ASME B16.20. New gaskets have been introduced for duplex stainless steel and titanium piping classes. 1.5.8 Miscellaneous The maximum size of vents and drains has been increased, relative to the header size. Non-piping items such as level gauges and level displacer have been removed from the piping classes. Thermowells have been PTS 31.38.01.11-Gen. replaced in accordance with new design. See PTS 31.38.01.15 January 2010 Page 6 1.5.9 Impact testing of austenitic stainless steel For application at temperatures below –101 °C, ASME B31.3 para 3.2.3.2.2 requires impact testing at the lower design temperature. This requirement has been reflected in the applicable austenitic stainless steel grade 304 cryogenic piping classes, through impact testing at –196 °C. PTS 31.38.01.15 January 2010 Page 7 2. PIPING CLASSES – SERVICES AND MATERIALS SELECTION INDEX This index is presented as an excel spreadsheet which is attached in the attachment. 31380184 Service and Material Selection Index Reference PTS Piping class PTS PTS Piping Piping class class (old) PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS PTS 1000 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001 1001-20 1001-KS 1002 1002 1002 1002 1002-KS 1003 1003-KS 1005 1007 1007 1007 1007-20 1008 1008-KS 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011-20 1012 1012-20 1013 1013-20 1015 1015-KS 1026 1026-KS 1031 1031-KS 1035 1035-KS 1036 1036-KS 1041 1041-20 1042 1042 1042 1042-20 1055 1055-20 1061 1061-KS 1071 1071-KS 1076 1076-KS 1085 1085 1085 1085 1085 1085 1085 1086 1092 1092-KS 1141 1141-KS 1142 1142-KS 1160 1174 1175 1176 1180 1180 1180 1201 1201 1210 1220 1261 1271 1301 1301-KS 1310 1374 1374-KS 1380 1380 1380 1384 2010 2011 2020 2021 2040 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 31.38.01.12 1021 1021 1021 1021 1021 1021 1021 1021 1021 1021 1021 1021 1021 1021 1021 1021 1021 1021 1023 1372 1372 1372 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1011 1012 1013 1015 1025 1031 1125 1126 1041 1042 1042 1042 1055 1131 1071 1076 1172 1172 1172 1172 1172 1172 1172 1173 1091 1160 1174 1175 1176 1180 1180 1180 1201 1201 1210 1220 1261 1271 1300 1310 1374 2010 2011 2020 2021 2040 Material PN ASME class barg 150 DN DN 300 DN DN 600 DN DN 900 DN DN 1500 DN DN 2500 DN DN (min) (max) (min) (max) (min) (max) (min) (max) (min) (max) (min) (max) 16.0 16.0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 600 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1 1 1 1 1 1 1 1 1 1 1 1 15 1200 15 600 15 600 15 600 15 600 15 600 15 600 15 600 15 600 15 600 15 600 15 600 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 600 600 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1 15 1200 1 1 1 1 1 1 1 1 1 1 1 15 15 15 15 15 15 15 15 15 15 15 1 1 1 15 1200 15 1200 15 1200 1 15 1200 1200 1200 600 600 1200 1200 600 600 600 600 1200 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 600 300 300 1200 1200 1200 1200 1 1 1 1 1 1 1 1 1 1 1 15 15 15 15 15 15 15 15 50 15 15 1200 1200 1200 1200 1200 1200 1200 1200 400 400 1200 1 1 15 15 600 600 1 1 1 1 1 1 1 1 15 1200 15 1200 15 1200 15 1200 15 1200 15 600 15 600 15 1200 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 600 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 600 600 600 600 600 600 600 600 600 600 600 600 600 600 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 600 600 600 600 1200 1200 600 600 600 600 1200 1200 1200 1200 1200 1200 1200 1200 600 600 1200 1200 600 600 1200 1200 1200 1200 1200 1200 1200 600 300 300 1200 1200 1200 1200 900 1200 1200 1200 1200 1200 1200 3 50 400 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 15 25 15 15 15 15 15 15 15 15 15 15 15 15 15 15 1200 150 600 600 300 1200 1200 1200 1200 1200 600 600 1200 1200 1200 1200 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 15 1200 15 1200 15 600 15 600 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 600 600 600 600 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 15 1200 15 1200 9 9 15 15 1200 1200 15 15 15 15 400 400 6 6 6 6 6 6 6 6 15 15 15 15 15 15 15 15 9 9 9 9 9 9 9 9 15 15 15 15 15 15 15 15 1200 1200 1200 1200 1200 1200 1200 1200 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 400 400 400 400 400 400 400 400 6 6 6 6 15 1200 15 1200 15 600 15 600 6 6 6 6 6 6 15 1200 15 1200 15 1200 15 1200 15 600 15 1200 6 6 6 6 15 1200 15 1200 15 1200 15 1200 6 6 6 6 6 6 6 6 6 6 6 6 15 15 15 15 15 15 15 15 15 15 15 15 600 1200 1200 1200 1200 1200 900 600 1200 600 600 600 9 9 9 9 9 9 9 9 9 15 15 15 15 15 15 15 15 15 1200 1200 600 600 15 15 15 15 15 15 15 15 200 200 600 600 1200 1200 1200 1200 600 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 400 400 6 6 1200 1200 1200 1200 1200 1200 1200 1200 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 400 9 9 9 9 9 15 15 15 15 15 600 600 1200 1200 1200 15 15 15 15 150 150 9 9 9 9 9 15 15 15 15 15 1200 1200 600 1200 600 15 15 300 15 15 15 15 600 300 25 25 25 25 15 15 15 15 300 300 500 500 Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Carbon steel LT fine grained Alloy steel (1.25Cr-0.5Mo) Alloy steel (1.25Cr-0.5Mo) Alloy steel (1.25Cr-0.5Mo) Alloy steel (1.25Cr-0.5Mo) Alloy steel (5Cr-0.5Mo) Sour service (note 2) moderate moderate moderate moderate moderate moderate moderate moderate moderate high high high high PWHT Corr. allow. PWHT PWHT PWHT PWHT PWHT PWHT PWHT PWHT PWHT PWHT PWHT high high high high moderate moderate moderate moderate moderate moderate high high moderate moderate moderate PWHT moderate PWHT moderate PWHT moderate PWHT moderate moderate moderate moderate moderate moderate moderate moderate PWHT moderate moderate moderate moderate moderate PWHT high high moderate moderate moderate PWHT moderate PWHT moderate PWHT moderate moderate moderate moderate PWHT PWHT PWHT PWHT 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 1 3 3 3 3 3 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 3 3 1 1 3 3 1 1 3 3 3 3 3 3 1 1 1 1 3 3 1 1 1 1 1 1 1 1 3 3 1 1 3 3 1 1 1 3 1 1 1 1 1 3 1 1 1 1 1 3 3 3 3 3 3 3 1 1 1 1 1 Valve ASME FETC B16.5 (note 13) mat. group A B B B B B B B B B B B B B B B B B B B B A A A A A A A B B B B B A A B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B A A A A A A A B B B B B B B B B A A A A B B B B B B B B B B B 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.3 1.3 1.3 1.3 1.3 1.3 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.9 1.9 1.9 1.9 1.13 Min -20 0 0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20 -20 -20 0 0 0 -20 0 -20 -20 -20/0 -20/0 -20/0 -20 0 -20 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20/0 -20 -20/0 -20 -20/0 -20 0 -20 0 -20 0 -20 0 -20 0 -20 -20/0 -20 -20/0 -20/0 -20/0 -20 -20/0 -20 0 -20 0 -20 0 -20 -50 -50 -50 -50 -50 -50 -50 -50 0 -20 0 -20 0 -20 0 -50 -50 -50 -50 -50 -50 0 0 0 0 0 -35 0 -20 -15 0 -20 -50 -50 -50 -50 -20 -20 0 0 -20 Max 400 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 340 210 210 400 340 150 150 150 150 400 400 400 400 400 400 400 400 150 150 400 340 400 340 150 150 150 150 150 150 150 150 65 150 400 340 400 340 410 340 340 340 340 340 340 90 90 200 200 400 70 150 150 150 400 340 340 340 340 340 450 550 450 538 450 where Tmin is between 0° and -20°C use PC 1000 1001-KS 1001-KS 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1001-20 1002 1002-KS 1002-KS 1002-KS 1003-KS 1005 1007-20 1007-20 1007-20 1008-KS Service index Ball Medium valve incl. Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Benzene Acetone Acetonitrile Air Butane Butene (Butylene) Butanol Diethylene glycol Ethanol Hydrocarbons Hydrocarbons Isobutanol Isopropyl alcohol Methanol (Methyl alcohol) Butanone (Methyl ethyl ketone) Nitrogen Polyols Propane Butanol (Sec-butyl alcohol) Benzene 1,3-Butadiene Hydrogen chloride Phenol Sodium hydroxide (Caustic soda) Y Y 1031-KS 1035-KS Chemical CAS RN formula (see note 5) DMK C6H6 C3H6O C2H3N DEG C3H8 C4H10O 71-43-2 67-64-1 75-05-8 106-97-8 25167-67-3 71-36-3 111-46-6 64-17-5 78-83-1 67-63-0 67-56-1 78-93-3 7727-37-9 74-98-6 78-92-2 C6H6 C4H6 HCl C6H6O 71-43-2 106-99-0 7647-01-0 108-95-2 C4H10 C4H8 C4H10O C4H10O3 C2H6O 9,12 9 IPA MEK unfinished neutral prod. gas liquid SBA gas gas, dry see PTS 31.38.01.11-Gen - Appendix 10 8 lean solvent rich solvent rich solvent lean solvent CO2 case H2S case 7 7 7 7 see PTS 31.38.01.11-Gen - Appendix 10 8 NaOH SBA DEG 3,9,12 3,9,12 3,9 9 IPA MEK gas unfinished neutral prod gas, dry treated non corrosive BFW Amine lean solvent 7 Hydrocarbons with wet H2S 9 1310-73-2 1310-73-2 Xi Xn R45 R46 0 0 0 0 Xn F+ F+ Xi Xn Xn 0 0 0 0 0 0 0 0 0 0 0 0 0 F Xi Xi F F F T Xi F+ Xi F F+ T C C Xi T T Xn R45 R46 R45 R46 Xn R68 C 0 0 0 0 Xi Xi 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Xn Xn F Xi Xi F F F T Xi - 0 - 0 - - 0 Water, sour with high severity HIC - 0 Hydrocarbons with wet H2S 2,9 - 0 1042-20 1042-20 1042-20 Hydrocarbons Hydrocarbons Water, sour with wet H2S with sulfur and/or naphthenic acids with wet H2S 2,9 6,9 - 0 240 0 Water, sour with high severity HIC Hydrogen with or without wet H2S check API 941 for pressure/temperature limit 2 H2 1333-74-0 F+ 0 1071-KS Hydrogen with or without wet H2S check API 941 for pressure/temperature limit 2 H2 1333-74-0 F+ 0 1076-KS Hydrogen with or without wet H2S check API 941 for pressure/temperature limit 2 H2 1333-74-0 F+ 0 1055-20 1061-KS 1092-KS Y Y Y Y Y Y Y Y Y Y Y Y Butane Butene (Butylene) Coolant Hydrocarbons Methanol (Methyl alcohol) Propane Propene (Propylene) Sulphuric acid > 65% wt Hydrogen sulphide gas, dry Hydrogen sulphide gas, dry 1301-KS Heat transfer fluid Hydrocarbons Hydrocarbons Coolant Hydrocarbons Propene (Propylene) Water, cooling Water, fire fighting Sulfur Steam Steam Chlorine Ethylene oxide 1374-KS - Hydrogen fluoride (Hydrofluoric acid) Amine Coolant Hydrocarbons Propene (Propylene) Hydrocarbons Hydrocarbons Steam Steam Hydrocarbons - gas/liquified gas 1142-KS Y Y Y corrosion rate must be checked liquid liquified gas 60% H2O + 40% Methanol with or without wet H2S 1141-KS Y Y 9 0 0 0 0 C 71-36-3 78-92-2 124-38-9 C4H10O3 111-46-6 C2H6O 64-17-5 C4H10O 78-83-1 C3H8O 67-63-0 CH4O 67-56-1 C4H8O 78-93-3 N2 7727-37-9 SO3 7446-11-9 - - with wet H2S T C4H10O C4H10O CO2 - Hydrocarbons F F F NaOH instrument, tool liquid dry non aerated all concentrations, dry anhydrous non corrosive non corrosive with wet H2S with sulfur and/or naphthenic acids finished product C4H10O C3H8O CH4O C4H8O N2 EU Dangerous Substances Directive Danger Classification (for explanation see tab "Dangerous substances") C E F/F+ N O T/T+ Xi Xn Carci Muta nogen gen Min 1041-20 1036-KS Y Y Y Y all concentrations, dry anhydrous non corrosive with wet H2S finished product >= 2%; area A - with tracing; area B see 1011 Short name instrument, tool gas gas >= 2%; area A - without tracing 1012-20 1026-KS Notes Sodium hydroxide (Caustic soda) Air Butanol Butanol (Sec-butyl alcohol) Carbon dioxide Condensate (ex-steam) Diethylene glycol Ethanol Hydrocarbons Hydrocarbons Hydrocarbons Hydrocarbons Isobutanol Isopropyl alcohol Methanol (Methyl alcohol) Butanone (Methyl ethyl ketone) Nitrogen Polyols Sulphur trioxide Water, boiler feed 1015-KS Remarks + water Amine Amine Amine Amine 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 1011-20 - 1013-20 Properties see PTS 31.38.01.11-Gen - Appendix 10 4 4 4 4,9 4 4 4 4 8 C4H10 C4H8 CH4O C3H8 C3H6 H2SO4 2 H2S 2 H2S see PTS 20.05.50.10 4 2,4,9 2,4,9 4 4,9 4 with or without wet H2S with or without wet H2S 60% H2O + 40% Methanol with or without wet H2S sweet sweet saturated saturated, superheated gas/liquid, dry max. 33% rich solvent check oxygen and corrosion rate/life jacketed; inner pipe jacketed; outer pipe superheated superheated with sulfur and/or naphthenic acids 11 S see PTS 31.38.01.11-Gen - Appendix 10 4 see PTS 31.38.01.11-Gen - Appendix 10 8 7 60% H2O + 40% Methanol with or without wet H2S 4 4,9 4 4 9 9 corrosion rate must be checked C3H6 6,9 EO Cl2 C2H4O HF HF C3H6 106-97-8 25167-67-3 67-56-1 74-98-6 115-07-1 7664-93-9 0 F+ F+ -50 F F+ F+ T C 0 7783-06-4 F+ N® T+ 7783-06-4 F+ N® T+ 115-07-1 7704-34-9 7782-50-5 75-21-8 7664-39-3 115-07-1 - -50 -50 -50 -50 -48 0 0 0 F+ N® F+ C T T T+ F+ Xi R45 R46 -50 -50 -50 -50 -48 0 0 130 150 0 -35 0 0 0 -50 -50 -48 400 400 240 Material specification Pipe seamless ASTM ASTM sml wld API welded ASTM A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 A333-6 - 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B 5L-B - A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A672-C65 cl 22 A691-1.25Cr cl 22 A691-1.25Cr cl 22 A691-1.25Cr cl 22 A691-1.25Cr cl 22 A691-5C PTS 31.38.01.84, Jan 2010 ASTM Fittings seamless ASTM seamless ASTM welded ASTM welded ASTM ASTM ASTM ASTM ASTM A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl A671-CC65 cl - A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WPB A234-WP11 A234-WP11 A234-WP11 A234-WP11 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 A420-WPL6 - A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WPBW A234-WP11W A234-WP11W A234-WP11W A234-WP11W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W A420-WPL6W - A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A182-F11 cl 2 A182-F11 cl 2 A182-F11 cl 2 A182-F11 cl 2 Forgings A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl - - A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A516-60/65/70 A387-11 cl 2 A387-11 cl 2 A387-11 cl 2 A387-11 cl 2 Plate Thermowell Meterrun Strainer (Y-type) Sieve Class 150 + 300 Studbolts Bolts ASTM or EN Nuts ASTM or EN Gaskets Type < DN 600 Sealing Winding Reinf Inner ring Centring Type ring > DN 600 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 B564 UNS N04400 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 321 stab HT AISI 316 AISI 321 stab HT AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 321 stab HT AISI 316 AISI 321 stab HT AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7M A193-B7M A193-B7M A193-B7M A193-B7 A193-B7 A193-B7M A193-B7M A193-B7M A193-B7M A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7M A193-B7M A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A320-L7/L43 A320-L7/L43 A320-L7/L43 A320-L7/L43 A320-L7/L43 A320-L7/L43 A320-L7/L43 A320-L7/L43 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A320-L7/L43 A320-L7M A320-L7M A320-L7/L43 A320-L7/L43 A320-L7/L43 A193-B7 A193-B7 A193-B7 A193-B7 A193-B7 A320-L7/L43 A193-B7 A193-B7 A193-B7M A193-B7 A193-B7 A320-L7/L43 A320-L7/L43 A320-L7/L43 A320-L7/L43 A193-B16 EN 10269 - 20CrMoVTiB4-10 A193-B16 EN 10269 - 20CrMoVTiB4-10 A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2HM A194-2HM A194-2HM A194-2HM A194-2H A194-2H A194-2HM A194-2HM A194-2HM A194-2HM A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2HM A194-2HM A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-4 A194-4 A194-4 A194-4 A194-4 A194-4 A194-4 A194-4 A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-2H A194-4 A194-7M A194-7M A194-4 A194-4 A194-4 A194-2H A194-2H A194-2H A194-2H A194-2H A194-4 A194-2H A194-2H A194-2HM A194-2H A194-2H A194-4 A194-4 A194-4 A194-4 A194-4 EN 10269 - 20CrMoVTiB4-10 A194-4 EN 10269 - 20CrMoVTiB4-10 Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Flat ring Flat ring Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Spiral wound Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite PTFE PTFE Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite anti-oxidant Graphite Graphite anti-oxidant AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 321 AISI 316 AISI 321 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 321 AISI 316 AISI 321 CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS CS Max > 150 A106-B 100 A106-B 130 A106-B 50 A106-B 60 A106-B A106-B 200 A106-B 150 A106-B 100 A106-B 200 A106-B 200 A106-B 100 A106-B 100 A106-B 100 A106-B 100 A106-B 200 A106-B 150 A106-B 200 A106-B 200 A106-B A106-B 85 A106-B 35 A106-B 100 A106-B 200 A106-B A106-B 80 A106-B 95 A106-B 110 A106-B 130 A106-B A106-B A106-B 50 A106-B 200 A106-B 200 A106-B 350 A106-B 250 A106-B 150 A106-B 100 A106-B 200 A106-B 330 A106-B 200 A106-B 240 A106-B 100 A106-B 100 A106-B 100 A106-B 100 A106-B 340 A106-B 150 A106-B 340 A106-B 250 A106-B A106-B A106-B A106-B 80 A106-B A106-B 200 A106-B A106-B A106-B 150 A106-B 150 A106-B 200 A106-B A106-B 200 A106-B 330 A106-B 200 A106-B A106-B 200 A106-B A106-B 200 A106-B 230 A106-B 230 A106-B 50 50 150 150 150 40 A106-B 200 A106-B 200 A106-B 400 A106-B 150 150 50 150 150 50 A106-B 50 A106-B 150 A106-B 200 A106-B 400 A106-B 70 50 A106-B 150 95 A106-B 50 150 150 A335-P11 A335-P11 450 A335-P11 538 A335-P11 450 A335-P5 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal Metal grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved Clamp type connector Sealing Grooved Centring Hub Appl profile ring Blind hub code ASTM Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 grooved Graphite AISI 316 AISI 316 grooved Graphite AISI 316 AISI 316 grooved grooved grooved grooved grooved grooved grooved grooved Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 grooved Graphite AISI 316 AISI 316 grooved grooved grooved grooved grooved grooved grooved grooved grooved grooved Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite Graphite AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 321 AISI 316 AISI 321 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 321 AISI 316 AISI 321 - Clamp ASTM - Appl Seal ring code - Valves Appl Body & Bonnet code ASTM forging A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A350-LF2 cl A105 A105 A105 A105 A350-LF2 cl A105 A350-LF2 cl A105 A105 A105 A105 A105 A105 A350-LF2 cl A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A105 A350-LF2 cl A105 A350-LF2 cl A105 A350-LF2 cl A105 A350-LF2 cl A105 A350-LF2 cl A105 A105 A105 A105 A105 A105 A105 A105 A105 A350-LF2 cl A105 A350-LF2 cl A105 A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A105 A350-LF2 cl A105 A350-LF2 cl A105 A350-LF2 cl A105 A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A105 A105 A105 A350-LF2 cl A105 A350-LF2 cl A350-LF2 cl A105 A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A350-LF2 cl A182-F11 cl A182-F11 cl A182-F11 cl A182-F11 cl 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 Check, Gate, Globe Trim AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, Alloy 20 Alloy 20 AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, AISI 316, Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite Alloy 400 AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 321, Stellite AISI 316, Stellite AISI 321, Stellite Body & Bonnet ASTM casting Trim Butterfly Trim Class 150-600 A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A352-LCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A352-LCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A352-LCC A352-LCC A352-LCC A352-LCC A352-LCC A352-LCC A352-LCC A352-LCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A352-LCC A352-LCC A352-LCC A352-LCC A352-LCC A216-WCB/WCC A216-WCB/WCC A216-WCB/WCC AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 316, Stellite AISI 410 AISI 410 AISI 410 AISI 410 AISI 316, Stellite AISI 410 AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 410 AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 410 AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite Alloy 20 Alloy 20 AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 410 AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 410 AISI 410 AISI 410 AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite Alloy 400 AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 316, Stellite AISI 321, Stellite AISI 316, Stellite AISI 321, Stellite CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 CS, Duplex, Stellite AISI 410 LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 410 LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, LTCS, Duplex, Stellite LTCS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 410 LTCS, Duplex, Stellite LTCS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, LTCS, Duplex, Stellite LTCS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, LTCS, Duplex, Stellite LTCS, Alloy 625, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, CS, Duplex, Stellite AISI 410 LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite LTCS, 17-4-PH, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, AISI 316, EPDM AISI 410, AISI 316, EPDM AISI 410, CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, CS, Duplex, Stellite LTCS, Duplex, Stellite CS, Duplex, Stellite CS, Alloy 625, Stellite AISI 316, LTCS, Duplex, Stellite LTCS, Alloy 625, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, LTCS, Duplex, Stellite AISI 316, 1.25Cr-0.5Mo, Duplex, Stellite 1.25Cr-0.5Mo, Alloy 625, Stellite AISI 316, 1.25Cr-0.5Mo, Alloy 625, Stellite 1.25Cr-0.5Mo, Alloy 625, Stellite AISI 321, 1.25Cr-0.5Mo, Duplex, Stellite 1.25Cr-0.5Mo, Alloy 625, Stellite AISI 316, 1.25Cr-0.5Mo, Alloy 625, Stellite 1.25Cr-0.5Mo, Alloy 625, Stellite AISI 321, A216-WCB/WCC A352-LCC A216-WCB/WCC A352-LCC A352-LCC A216-WCB/WCC A352-LCC A352-LCC A352-LCC A352-LCC A352-LCC A217-WC6 A217-WC6 A217-WC6 A217-WC6 Trim Class 900 Dual plate check Ball (ISO 17292) Trim Internal seat Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite FKM FKM Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite Stellite AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, Stellite AISI 316, Stellite AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE AISI 316, PTFE Alloy 400, PTFE AISI 316, Stellite AISI 316, Stellite - Ball (API 6D/ISO 14313) Internal seat Internal seat Class 150-300 Class 600-2500 Plug Trim - - - - - AISI 410 Alloy 400, - General 1 Selection between 1 and 3 mm corrosion allowance ptsending on the corrosivety of the medium has to be selected by the corrosion engineer. 2 For the definition of "High Sour" and "Moderate Sour", see PTS 31.38.01.11, Appendix 10. 3 4 5 6 7 8 9 10 11 12 13 14 15 Notes for R&C piping classes Specific Piping classes 31011 and 31012 are interchangeable. See PTS 30.10.02.31 for low temperature service. Chemical Abstracts Service Registry Number Consult a corrosion engineer for a check on the high temperature sulphidation corrosion rate and select materials accordingly. Amine includes ADIP, MEA, DEA, AD, TEA and Sulfinol: H2S case = H2S/CO2 > 0.01 for gas phase, > 0.02 for liquid phase; CO2 case = H2S/CO2 < 0.01 for gas phase, > 0.02 for liquid phase. Selection shall be carried out by materials engineer on the the basis of the specific process conditions. Hydrocarbon service includes aviation alkylate, LPG, C1-C4, paraffins and olefins, fuel gas, fuel oil, gasoil, gasoline, isopentane, luboil, naphtha, pentane, toluene and xylene. See PTS 31.40.10.19 for the use of GRP piping. See PTS 80.47.10.31 for fire fighting installations. H2 pp < 7 bar; wet H2S < 50 mg/kg; wet HCN < 20 wppm; S < 0.3 wt. %; TAN < 0.3; H2S < 0.01 mol.% See MESC SPE 77/302 for Fugitive Emission Tightness Class Minimum and maximum temperature relate to the design limits of the piping class components inptsendent of the medium The applicable temperature range, encountered in practice, may be determined by the medium, e.g. due to corrosion. These temperatures provides guidance Notes for E&P piping classes Specific 20 Piping classes 31410 and 31411; 31450 and 31451 are interchangeable. Labeling of dangerous substances and preparations Symbols and indications of danger for dangerous substances and preparations [1] E : Explosive O : Oxidizing F+ : Extremely flammable F : Highly flammable T+ : Very toxic C : Corrosive Xn : Harmful Xi : Irritant N : Dangerous to the environment N® : Dangerous to the environment, including R50 Definitions T : Toxic The following substances and preparations are "dangerous" (EC-Directive 92/32/EEC) [2]: Explosive substances and preparations: solid, liquid, pasty or gelatinous substances and preparations which may also react exothermically without atmospheric oxygen thereby quickly evolving gases, and which, under defined test conditions, detonate, quickl Oxidising substances and preparations: substances and preparations which give rise to a highly exothermic reaction in contact with other substances, particularly flammable substances. Extremely flammable substances and preparations: liquid substances and preparations having an extremely low flash-point and a low boiling-point and gaseous substances and preparations which are flammable in contact with air at ambient temperature and pres Highly flammable substances and preparations: - substances and preparations which may become hot and finally catch fire in contact with air at ambient temperature without any application of energy, or - solid substances and preparations which may readily catch fire after brief contact with a source of ignition and which continue to burn or to be consumed after removal of the source of ignition, or - liquid substances and preparations having a very low flash-point, or - substances and preparations which, in contact with water or damp air, evolve highly flammable gases in dangerous quantities. Flammable substances and preparations: liquid substances and preparations having a low flash-point. Very toxic substances and preparations: substances and preparations which in very low quantities cause death or acute or chronic damage to health when inhaled, swallowed or absorbed via the skin. Toxic substances and preparations: substances and preparations which in low quantities cause death or acute or chronic damage to health when inhaled, swallowed or absorbed via the skin. Harmful substances and preparations: substances and preparations which may cause death or acute or chronic damage to health when inhaled, swallowed or absorbed via the skin. Corrosive substances and preparations: substances and preparations which may, on contact with living tissues, destroy them. Irritant substances and preparations: non-corrosive substances and preparations which, through immediate, prolonged or repeated contact with the skin or mucous membrane, may cause inflammation. Sensitizing substances and preparations: substances and preparations which, if they are inhaled or if they penetrate the skin, are capable of eliciting a reaction of hypersensitization such that on further exposure to the substance or preparation, charact Carcinogenic substances and preparations: substances or preparations which, if they are inhaled or ingested or if they penetrate the skin, may induce cancer or increase its incidence. Mutagenic substances and preparations: substances and preparations which, if they are inhaled or ingested or if they penetrate the skin, may induce heritable genetic defects or increase their incidence. Substances and preparations which are toxic for reproduction: substances and preparations which, if they are inhaled or ingested or if they penetrate the skin, may produce, or increase the incidence of, non-heritable adverse effects in the progeny and/or Substances and preparations which are dangerous for the environment: substances and preparations which, were they to enter the environment, would present or may present an immediate or delayed danger for one or more components of the environment. Page 1 of 7 Labeling of dangerous substances and preparations Nature of special risks attributed to dangerous substances and preparations: R- and S-phrases [3] Nature of special risks attributed to dangerous substances and preparations: R-phrases R1 Explosive when dry R2 Risk of explosion by shock, friction, fire or other sources of ignition R3 Extreme risk of explosion by shock, friction, fire or other sources of ignition R4 Forms very sensitive explosive metallic compounds R5 Heating may cause an explosion R6 Explosive with or without contact with air R7 May cause fire R8 Contact with combustible material may cause fire R9 Explosive when mixed with combustible material R 10 Flammable R 11 Highly flammable R 12 Extremely flammable R 14 Reacts violently with water R 15 Contact with water liberates extremely flammable gases R 16 Explosive when mixed with oxidizing substances R 17 Spontaneously flammable in air R 18 In use, may form flammable/explosive vapour-air mixture R 19 May form explosive peroxides R 20 Harmful by inhalation R 21 Harmful in contact with skin R 22 Harmful if swallowed R 23 Toxic by inhalation R 24 Toxic in contact with skin R 25 Toxic if swallowed R 26 Very toxic by inhalation R 27 Very toxic in contact with skin R 28 Very toxic if swallowed R 29 Contact with water liberates toxic gas R 30 Can become highly flammable in use R 31 Contact with acids liberates toxic gas R 32 Contact with acids liberates very toxic gas R 33 Danger of cumulative effects R 34 Causes burns R 35 Causes severe burns R 36 Irritating to eyes R 37 Irritating to respiratory system R 38 Irritating to skin R 39 Danger of very serious irreversible effects R 40 Limited evidence of a carcinogenic effect R 41 Risk of serious damage to eyes R 42 May cause sensitization by inhalation R 43 May cause sensitization by skin contact R 44 Risk of explosion if heated under confinement R 45 May cause cancer R 46 May cause heritable genetic damage R 48 Danger of serious damage to health by prolonged exposure R 49 May cause cancer by inhalation R 50 Very toxic to aquatic organisms R 51 Toxic to aquatic organisms R 52 Harmful to aquatic organisms R 53 May cause long-term adverse effects in the aquatic environment R 54 Toxic to flora R 55 Toxic to fauna R 56 Toxic to soil organisms R 57 Toxic to bees R 58 May cause long-term adverse effects in the environment R 59 Dangerous for the ozone layer R 60 May impair fertility R 61 May cause harm to the unborn child R 62 Possible risk of impaired fertility R 63 Possible risk of harm to the unborn child R 64 May cause harm to breastfed babies R 65 Harmful: may cause lung damage if swallowed R 66 Repeated exposure may cause skin dryness or cracking Page 2 of 7 Labeling of dangerous substances and preparations R 67 Vapours may cause drowsiness and dizziness Page 3 of 7 Labeling of dangerous substances and preparations R 68 R 14/15 R 15/29 R 20/21 R 20/22 R 20/21/22 R 21/22 R 23/24 R 23/25 R 23/24/25 R 24/25 R 26/27 R 26/28 R 26/27/28 R 27/28 R 36/37 R 36/38 R 36/37/38 R 37/38 R 39/23 R 39/24 R 39/25 R 39/23/24 R 39/23/25 R 39/24/25 R 39/23/24/25 R 39/26 R 39/27 R 39/28 R 39/26/27 R 39/26/28 R 39/27/28 R 39/26/27/28 R 42/43 R 48/20 R 48/21 R 48/22 R 48/20/21 R 48/20/22 R 48/21/22 R 48/20/21/22 Possible risk of irreversible effects Reacts violently with water, liberating extremely flammable gases Contact with water liberates toxic, extremely flammable gas Harmful by inhalation and in contact with skin Harmful by inhalation and if swallowed Harmful by inhalation, in contact with skin and if swallowed Harmful in contact with skin and if swallowed Toxic by inhalation and in contact with skin Toxic by inhalation and if swallowed Toxic by inhalation, in contact with skin and if swallowed Toxic in contact with skin and if swallowed Very toxic by inhalation and in contact with skin Very toxic by inhalation and if swallowed Very toxic by inhalation, in contact with skin and if swallowed Very toxic in contact with skin and if swallowed Irritating to eyes and respiratory system Irritating to eyes and skin Irritating to eyes, respiratory system and skin Irritating to respiratory system and skin Toxic: danger of very serious irreversible effects through inhalation Toxic: danger of very serious irreversible effects in contact with skin Toxic: danger of very serious irreversible effects if swallowed Toxic: danger of very serious irreversible effects through inhalation and in contact with skin Toxic: danger of very serious irreversible effects through inhalation and if swallowed Toxic: danger of very serious irreversible effects in contact with skin and if swallowed Toxic: danger of very serious irreversible effects through inhalation, in contact with skin and if swallowed Very toxic: danger of very serious irreversible effects through inhalation Very toxic: danger of very serious irreversible effects in contact with skin Very toxic: danger of very serious irreversible effects if swallowed Very toxic: danger of very serious irreversible effects through inhalation and in contact with skin Very toxic: danger of very serious irreversible effects through inhalation and if swallowed Very toxic: danger of very serious irreversible effects in contact with skin and if swallowed Very toxic: danger of very serious irreversible effects through inhalation, in contact with skin and if swallowed May cause sensitisation by inhalation and skin contact Harmful: danger of serious damage to health by prolonged exposure through inhalation Harmful: danger of serious damage to health by prolonged exposure in contact with skin Harmful: danger of serious damage to health by prolonged exposure if swallowed Harmful: danger of serious damage to health by prolonged exposure through inhalation and in contact with skin Harmful: danger of serious damage to health by prolonged exposure through inhalation and if swallowed Harmful: danger of serious damage to health by prolonged exposure in contact with skin and if swallowed Harmful: danger of serious damage to health by prolonged exposure through inhalation, in contact with skin and if swallowed R 48/23 R 48/24 R 48/25 R 48/23/24 R 48/23/25 R 48/24/25 R 48/23/24/25 Toxic: danger of serious damage to health by prolonged exposure through inhalation Toxic: danger of serious damage to health by prolonged exposure in contact with skin Toxic: danger of serious damage to health by prolonged exposure if swallowed Toxic: danger of serious damage to health by prolonged exposure through inhalation and in contact with skin Toxic: danger of serious damage to health by prolonged exposure through inhalation and if swallowed Toxic: danger of serious damage to health by prolonged exposure in contact with skin and if swallowed Toxic: danger of serious damage to health by prolonged exposure through inhalation, in contact with skin and if swallowed Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment Harmful: possible risk of irreversible effects through inhalation Harmful: possible risk of irreversible effects in contact with skin Harmful: possible risk of irreversible effects if swallowed Harmful: possible risk of irreversible effects through inhalation and in contact with skin Harmful: possible risk of irreversible effects through inhalation and if swallowed Harmful: possible risk of irreversible effects in contact with skin and if swallowed Harmful: possible risk of irreversible effects through inhalation, in contact with skin and if swallowed R 50/53 R 51/53 R 52/53 R 68/20 R 68/21 R 68/22 R 68/20/21 R 68/20/22 R 68/21/22 R 68/20/21/22 Page 4 of 7 Labeling of dangerous substances and preparations Safety advice concerning dangerous substances and preparations: S-phrases S1 Keep locked up S2 Keep out of the reach of children S3 Keep in a cool place S4 Keep away from living quarters S5 Keep contents under ... (appropriate liquid to be specified by the manufacturer) S6 Keep under ... (inert gas to be specified by the manufacturer) S7 Keep container tightly closed S8 Keep container dry S9 Keep container in a well-ventilated place S 12 Do not keep the container sealed S 13 Keep away from food, drink and animal feedingstuffs S 14 Keep away from ... (incompatible materials to be indicated by the manufacturer) S 15 Keep away from heat S 16 Keep away from sources of ignition - No smoking S 17 Keep away from combustible material S 18 Handle and open container with care S 20 When using do not eat or drink S 21 When using do not smoke S 22 Do not breathe dust S 23 Do not breathe gas/fumes/vapour/spray (appropriate wording to be specified by the manufacturer) S 24 Avoid contact with skin S 25 Avoid contact with eyes S 26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice S 27 Take off immediately all contaminated clothing S 28 After contact with skin, wash immediately with plenty of ... (to be specified by the manufacturer) S 29 Do not empty into drains S 30 Never add water to this product S 33 Take precautionary measures against static discharges S 35 This material and its container must be disposed of in a safe way S 36 Wear suitable protective clothing S 37 Wear suitable gloves S 38 In case of insufficient ventilation, wear suitable respiratory equipment S 39 Wear eye/face protection S 40 To clean the floor and all objects contaminated by this material, use ... (to be specified by the manufacturer) S 41 In case of fire and/or explosion do not breathe fumes During fumigation/spraying wear suitable respiratory equipment (appropriate wording to be specified by the S 42 manufacturer) S 43 In case of fire, use ... (indicate in the space the precise type of fire-fighting equipment. If water increases risk, add "Never use water") S 45 S 46 S 47 S 48 S 49 S 50 S 51 S 52 S 53 S 56 S 57 S 59 S 60 S 61 S 62 S 63 S 64 S 1/2 S 3/7 S 3/9/14 S 3/9/14/49 In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible) If swallowed, seek medical advice immediately and show this container or label Keep at temperature not exceeding ... °C (to be specified by the manufacturer) Keep wet with ... (appropriate material to be specified by the manufacturer) Keep only in the original container Do not mix with ... (to be specified by the manufacturer) Use only in well-ventilated areas Not recommended for interior use on large surface areas Avoid exposure - obtain special instructions before use Dispose of this material and its container to hazardous or special waste collection point Use appropriate container to avoid environmental contamination Refer to manufacturer/supplier for information on recovery/recycling This material and its container must be disposed of as hazardous waste Avoid release to the environment. Refer to special instructions/safety data sheets If swallowed, do not induce vomiting: seek medical advice immediately and show this container or label In case of accident by inhalation: remove casualty to fresh air and keep at rest If swallowed, rinse mouth with water (only if the person is conscious) Keep locked up and out of the reach of children Keep container tightly closed in a cool place Keep in a cool, well-ventilated place away from ... (incompatible materials to be indicated by the manufacturer) Keep only in the original container in a cool, well-ventilated place away from ... (incompatible materials to be indicated by the manufacturer) S 3/9/49 S 3/14 S 7/8 S 7/9 S 7/47 Keep only in the original container in a cool, well-ventilated place Keep in a cool place away from ... (incompatible materials to be indicated by the manufacturer) Keep container tightly closed and dry Keep container tightly closed and in a well-ventilated place Keep container tightly closed and at a temperature not exceeding ... °C (to be specified by the manufacturer) Page 5 of 7 Labeling of dangerous substances and preparations S 20/21 When using do not eat, drink or smoke Page 6 of 7 Labeling of dangerous substances and preparations S 24/25 S 27/28 Avoid contact with skin and eyes After contact with skin, take off immediately all contaminated clothing, and wash immediately with plenty of ... (to be specified by the manufacturer) S 29/35 S 29/56 S 36/37 S 36/37/39 S 36/39 S 37/39 S 47/49 Do not empty into drains; dispose of this material and its container in a safe way Do not empty into drains, dispose of this material and its container at hazardous or special waste collection point Wear suitable protective clothing and gloves Wear suitable protective clothing, gloves and eye/face protection Wear suitable protective clothing and eye/face protection Wear suitable gloves and eye/face protection Keep only in the original container at a temperature not exceeding ... °C (to be specified by the manufacturer) References [1] Source: EC-Directive 2001/59/EC ; Annex II [2] Source: EC-Directive 92/32/EEC [3] Source: EC-Directive 2001/59/EC ; Annex III Page 7 of 7 PTS 31.38.01.15 January 2010 Page 8 3. PIPING CLASSES The piping classes for ASME class ratings 150, 300, 600, 900, 1500 and 2500 are contained in separate file with this PTS number. The piping classes are in numerical order within each ASME class rating. PTS 31.38.01.15 January 2010 Page 9 4. REFERENCES In this PTS, reference is made to the following publications: NOTES: 1. Unless specifically designated by date, the latest edition of each publication shall be used, together with any amendments/supplements/revisions thereto. 2. Excluded from this list are the standards referenced in the piping classes themselves, a list of which would be too extensive. PETRONAS STANDARDS Piping classes - Basis of design PTS 31.38.01.10 Piping - General requirements PTS 31.38.01.11 Piping classes - Refining and chemicals PTS 31.38.01.12 Selection of materials for life cycle performance (EP) PTS 39.01.10.11 AMERICAN STANDARDS Pipe flanges and flanged fittings ASME B16.5 Metallic gaskets for pipe flanges ASME B16.20 ring-joint, spiral-wound, and jacketed Process piping ASME B31.3 Issued by: American Society of Mechanical Engineers 345 East 47th Street New York NY 10017 USA Standard specification for steel castings, carbon, suitable for fusion welding, for high-temperature service ASTM A 216 Issued by: American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, USA BRITISH STANDARDS Spiral wound gaskets for steel flanges to BS 1560 BS 3381 Issued by: British Standards Institution 389 Chiswick High Road London W4 4AL UK INTERNATIONAL STANDARDS Metal ball valves for petroleum, petrochemical and allied industries Issued by: International Organisation for Standardisation Case Postale 56 Geneva 20 Switzerland CH-1211 Copies can also be obtained from national standards organizations. ISO 17292 PTS 31.38.01.15 January 2010 Page 10 5. APPENDIX A : DETAILED CHANGES PER PIPING CLASS This index is presented as an excel spreadsheet which is attached in the attachment. 31380115- January 2010 Revision Summa 31380115- January 2006 - Revision Summary.xls E E E E E E E E E E E E A A A A A A A A A A A A A A A A A A A A A A A D D A A C C C C C C C C A A C C A A Valves gate Valves check dual plate Valves butterfly Valves ball (ISO 14313) 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 - Valves ball (ISO 17292) O O O O O O O O O O O O O O O O O O O D D D D C C C C C C B B C D D D C A C C D D C O O O O O - Valves ball (BS 5351) 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 Spade flange C C C C B B O C C C C B B C C C C B B C C C C B B B B B B A A B C C C B O B B C C B C C C C B C C C C P/T rating 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Meterrun 150 300 600 900 1500 2500 300 150 300 600 900 1500 2500 300 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 300 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 Current revision date Gaskets Previous revision date Present revision letter Previous revision letter Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Corrosion allowance 1410 1410 1410 1410 1410 1410 1411 1412 1412 1412 1412 1412 1412 1413 1420 1420 1420 1420 1420 1420 1422 1422 1422 1422 1422 1422 1430 1430 1430 1430 1430 1430 1432 1432 1432 1432 1432 1432 1440 1440 1440 1440 1440 1440 1441 1441 1441 1441 1441 1441 1450 1450 1450 1450 1450 1451 1460 1460 1460 1460 1460 1470 1470 1470 1470 1470 1472 1472 1472 1472 1472 1480 1480 1480 1480 Material Description ASME rating 1 3 6 9 15 25 3 1 3 6 9 15 25 3 1 3 6 9 15 25 1 3 6 9 15 25 1 3 6 9 15 25 1 3 6 9 15 25 1 3 6 9 15 25 1 3 6 9 15 25 1 3 6 9 15 3 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 Base Piping Class Rating PTS 31.38.01.15, January 2010 - Revisions overview C A D D C A A D D A A A A A D A A A A A D Legend A = added C = changed/corrected D = deleted E = extended R = reviewed/corrected Y = yes Remarks Deleted; replaced by PC 11412 Deleted; replaced by PC 31412 Deleted; replaced by PC 61412 Deleted; replaced by PC 91412 Deleted; replaced by PC 151412 Deleted; replaced by PC 251412 Deleted; replaced by PC 31413 New New New New New New New Deleted; replaced by PC 11422 Deleted; replaced by PC 31422 Deleted; replaced by PC 61422 Deleted; replaced by PC 91422 Deleted; replaced by PC 151422 Deleted; replaced by PC 251422 New New New New New New Deleted; replaced by PC 11432 Deleted; replaced by PC 31432 Deleted; replaced by PC 61432 Deleted; replaced by PC 91432 Deleted; replaced by PC 151432 Deleted; replaced by PC 251432 New New New New New New Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Deleted; replaced by PC 11472 Deleted; replaced by PC 31472 Deleted; replaced by PC 61472 Deleted; replaced by PC 91472 Deleted; replaced by PC 151472 New New New New New Deleted; replaced by PC 11482 Deleted; replaced by PC 31482 Deleted; replaced by PC 61482 Deleted; replaced by PC 91482 31380115- January 2006 - Revision Summary.xls 15 1 3 6 9 15 25 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 9 15 25 9 15 25 9 15 25 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1480 1482 1482 1482 1482 1482 1485 1490 1490 1490 1490 1490 1492 1492 1492 1492 1492 1500 1500 1500 1500 1500 1501 1501 1501 1501 1501 1502 1502 1502 1502 1502 1503 1503 1503 1503 1503 1520 1520 1520 1521 1521 1521 1522 1522 1522 3410 3410 3410 3410 3410 3411 3411 3411 3411 3411 3420 3420 3420 3420 3420 3421 3421 3421 3421 3421 3430 3430 3430 3430 3430 3450 3450 3450 3450 3450 3451 3451 3451 3451 3451 3460 3460 3460 3460 3460 Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel Sour Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour 1500 150 300 600 900 1500 2500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 900 1500 2500 900 1500 2500 900 1500 2500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 1 1 1 1 1 1 1 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B C C C C B C C C C B B B B B A C B B B A A C C C C B B B B B A C B C C B C C C C B C C C C B 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 O O O O O O O O O O O O O O O O O O O O O C B B O O O O O O O O O O O O O D C D D C O O O O O - 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 - C C C C C A A A A A D A A A A A D Deleted; replaced by PC 151482 New New New New New New Deleted; replaced by PC 11492 Deleted; replaced by PC 31492 Deleted; replaced by PC 61492 Deleted; replaced by PC 91492 Deleted; replaced by PC 151492 New New New New New Deleted; replaced by PC 11502 Deleted; replaced by PC 31502 Deleted; replaced by PC 61502 Deleted; replaced by PC 91502 Deleted; replaced by PC 151502 Deleted; replaced by PC 11503 Deleted; replaced by PC 31503 Deleted; replaced by PC 61503 Deleted; replaced by PC 91503 Deleted; replaced by PC 151503 New New New New New New New New New New Hold Hold Hold Revised (HOLD) Revised (HOLD) Revised (HOLD) New (HOLD) New (HOLD) New (HOLD) Deleted; replaced by PC 13411 Deleted; replaced by PC 33411 Deleted; replaced by PC 63411 Deleted; replaced by PC 93411 Deleted; replaced by PC 153411 New New New New New Deleted; replaced by PC 13421 Deleted; replaced by PC 33421 Deleted; replaced by PC 63421 Deleted; replaced by PC 93421 Deleted; replaced by PC 153421 New New New New New Revised Revised Revised Revised Revised Deleted; replaced by PC 13451 Deleted; replaced by PC 33451 Deleted; replaced by PC 63451 Deleted; replaced by PC 93451 Deleted; replaced by PC 153451 New New New New New Deleted; replaced by PC 13461 Deleted; replaced by PC 33461 Deleted; replaced by PC 63461 Deleted; replaced by PC 93461 Deleted; replaced by PC 153461 31380115- January 2006 - Revision Summary.xls 1 3 6 9 15 1 3 6 9 1 1 3 6 9 15 25 1 3 6 9 15 25 1 3 6 9 15 25 1 3 6 9 15 25 1 6 9 1 25 1 3 6 9 1 1 3461 3461 3461 3461 3461 3620 3620 3620 3620 3625 3831 3831 3831 3831 3831 3831 3832 3832 3832 3832 3832 3832 3833 3833 3833 3833 3833 3833 3834 3834 3834 3834 3834 3834 6410 6520 6520 6560 6560 6620 6620 6620 6620 8410 8420 Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel 6Mo LT Sour [A] Stainl steel 6Mo LT Sour [A] Stainl steel 6Mo LT Sour [A] Stainl steel 6Mo LT Sour [A] Stainl steel 6Mo LT Sour [A] Duplex stainless steel Duplex stainless steel Duplex stainless steel Duplex stainless steel Duplex stainless steel Duplex stainless steel Duplex stainless steel Sour Duplex stainless steel Sour Duplex stainless steel Sour Duplex stainless steel Sour Duplex stainless steel Sour Duplex stainless steel Sour Duplex stainless steel LT Duplex stainless steel LT Duplex stainless steel LT Duplex stainless steel LT Duplex stainless steel LT Duplex stainless steel LT Duplex stainless steel LT Sour Duplex stainless steel LT Sour Duplex stainless steel LT Sour Duplex stainless steel LT Sour Duplex stainless steel LT Sour Duplex stainless steel LT Sour Titanium Alloy 625 LT Sour [A] Alloy 625 LT Sour [A] Alloy 625 LT Sour Alloy 625 LT Sour Alloy 825 LT Sour [A] Alloy 825 LT Sour [A] Alloy 825 LT Sour [A] Alloy 825 LT Sour [A] Carbon steel Galvanised Carbon steel Galvanised 150 300 600 900 1500 150 300 600 900 150 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 600 900 150 2500 150 300 600 900 150 150 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B B B B B B B B B B B B B B B B B B B B B B B B A C C 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 12/1999 O O O O O O O O O O C C C C C C C C C C C C C C C C C C C C C C C C B O O O O O O O O - 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 - C C C C C C C C C C C C C C C C C C C C C C C C C E E E E E E E E E E E E E E E E E E E E E E E E D A C C C C C A A D D D A C C C C C A A D D D A C C C C C A A D D D A C C C C C A A D D D A New New New New New New New New New New Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised Revised New New New New New New New New Deleted; see PC 18011 Deleted; see PC 18011 General changes (not listed above): 1 Assemblies reviewed and changed, where applicable 2 Ball valves with carbon steel electroless nickel plated balls have been replaced by stainless steel balls; see PTS 39.01.10.11 - Appendix 9 3 Boltsets reviewed and changed, where applicable 4 BS5351 ball valves (withdrawn) replaced by ISO17292 ball valves 5 Butterfly valves triple excentric: minimum size changed to DN 200 6 Graphite tanged insert gaskets replaced by spiral wound gaskets 7 Level displacer chambers removed 8 Level gauges removed; see PTS 31.38.01.10 9 P/T rating reviewed and changed, where applicable 10 Pipe nipples removed 11 Spades added 12 Spectacle blinds limited; see PTS 31.38.01.11, para 8.7.2 13 Spiral wound gaskets changed to ASME B16.20; standardised on innerring and centring ring 14 Swing type checkvalves limited to DN 250 in ball valve piping classes due to the use of dual plate check valves 15 Thermowells replaced; cover flanges removed 16 Small bore ball valves standardised on full bore Headings Ra 1 3 6 9 15 25 3 1 3 6 9 15 25 3 1 3 6 9 15 25 1 3 6 9 15 25 1 3 6 9 15 25 1 3 6 9 15 25 1 1 3 3 6 6 9 9 15 15 25 25 1 1 3 3 6 6 9 9 15 15 25 25 1 1 3 3 6 Base 1410 1410 1410 1410 1410 1410 1411 1412 1412 1412 1412 1412 1412 1413 1420 1420 1420 1420 1420 1420 1422 1422 1422 1422 1422 1422 1430 1430 1430 1430 1430 1430 1432 1432 1432 1432 1432 1432 1440 1440 1440 1440 1440 1440 1440 1440 1440 1440 1440 1440 1441 1441 1441 1441 1441 1441 1441 1441 1441 1441 1441 1441 1450 1450 1450 1450 1450 Material description CARBON STEEL CARBON STEEL CARBON STEEL CARBON STEEL CARBON STEEL CARBON STEEL CARBON STEEL Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel CARBON STEEL SOUR CARBON STEEL SOUR CARBON STEEL SOUR CARBON STEEL SOUR CARBON STEEL SOUR CARBON STEEL SOUR Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour Carbon steel Sour CARBON STEEL CARBON STEEL CARBON STEEL CARBON STEEL CARBON STEEL CARBON STEEL Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel CARBON STEEL Carbon steel CARBON STEEL Carbon steel Ca 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1 1 1 1 1 Class 150 300 600 900 1500 2500 300 150 300 600 900 1500 2500 300 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 300 600 900 1500 2500 150 150 300 300 600 600 900 900 1500 1500 2500 2500 150 150 300 300 600 600 900 900 1500 1500 2500 2500 150 150 300 300 600 Br BD BF BS BS BS BS BF BD BF BS BS BS BS BF BD BF BS BS BS BS BD BF BS BS BS BS BL BP BS BS BS BS BL BP BS BS BS BS BL BL BP BP BS BS BS BS BS BS BS BS BL BL BP BP BS BS BS BS BS BS BS BS BD BD BF BF BS Revision C C C C B B O O O O O O O O C C C C B B O O O O O O C C C C B B O O O O O O D C D C D C D C C B C B C B C B C B C B B A B A C B D C D Page 1 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 Headings 6 9 9 15 15 3 3 1 1 3 3 6 6 9 9 15 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 9 1450 1450 1450 1450 1450 1451 1451 1460 1460 1460 1460 1460 1460 1460 1460 1460 1460 1470 1470 1470 1470 1470 1472 1472 1472 1472 1472 1480 1480 1480 1480 1480 1482 1482 1482 1482 1482 1490 1490 1490 1490 1490 1492 1492 1492 1492 1492 1500 1500 1500 1500 1500 1501 1501 1501 1501 1501 1502 1502 1502 1502 1502 1503 1503 1503 1503 1503 1520 CARBON STEEL Carbon steel CARBON STEEL Carbon steel CARBON STEEL Carbon steel CARBON STEEL Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR CARBON STEEL LT F-GR CARBON STEEL LT F-GR CARBON STEEL LT F-GR CARBON STEEL LT F-GR CARBON STEEL LT F-GR Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour CARBON STEEL LT F-GR CARBON STEEL LT F-GR CARBON STEEL LT F-GR CARBON STEEL LT F-GR CARBON STEEL LT F-GR Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr Carbon steel LT F-Gr CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR CARBON STEEL LT F-GR SOUR Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour Carbon steel LT F-Gr Sour CARBON STEEL SOUR 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 600 900 900 1500 1500 300 300 150 150 300 300 600 600 900 900 1500 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 900 BS BS BS BS BS BF BF BD BD BF BF BS BS BS BS BS BS BC BF BS BS BS BR BF BS BS BS BC BF BS BS BS BC BF BS BS BS BM BP BS BS BS BM BP BS BS BS BM BP BS BS BS BM BP BS BS BS BM BP BS BS BS BM BP BS BS BS BS C D C C B A O C B C B D C D C C B C C C C B O O O O O C C C C B O O O O O C C C C B O O O O O C C C C B B B B B A O O O O O O O O O O C Page 2 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 Headings 15 25 9 9 15 15 25 25 9 15 25 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 1 3 3 6 6 9 9 15 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 15 1 3 6 9 1 1 1 1520 1520 1521 1521 1521 1521 1521 1521 1522 1522 1522 3410 3410 3410 3410 3410 3411 3411 3411 3411 3411 3420 3420 3420 3420 3420 3421 3421 3421 3421 3421 3430 3430 3430 3430 3430 3430 3430 3430 3430 3430 3450 3450 3450 3450 3450 3451 3451 3451 3451 3451 3460 3460 3460 3460 3460 3461 3461 3461 3461 3461 3620 3620 3620 3620 3625 3831 3831 CARBON STEEL SOUR CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour CARBON STEEL SOUR Carbon steel Sour Carbon steel Sour Carbon steel Sour STAINL STEEL AISI 316 STAINL STEEL AISI 316 STAINL STEEL AISI 316 STAINL STEEL AISI 316 STAINL STEEL AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 Stainl steel AISI 316 STAINL STEEL AISI 316 SOUR STAINL STEEL AISI 316 SOUR STAINL STEEL AISI 316 SOUR STAINL STEEL AISI 316 SOUR STAINL STEEL AISI 316 SOUR Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 Sour Stainl steel AISI 316 STAINL STEEL AISI 316 Stainl steel AISI 316 STAINL STEEL AISI 316 Stainl steel AISI 316 STAINL STEEL AISI 316 Stainl steel AISI 316 STAINL STEEL AISI 316 Stainl steel AISI 316 STAINL STEEL AISI 316 STAINL STEEL AISI 316 LT STAINL STEEL AISI 316 LT STAINL STEEL AISI 316 LT STAINL STEEL AISI 316 LT STAINL STEEL AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT Stainl steel AISI 316 LT STAINL STEEL AISI 316 LT SOUR STAINL STEEL AISI 316 LT SOUR STAINL STEEL AISI 316 LT SOUR STAINL STEEL AISI 316 LT SOUR STAINL STEEL AISI 316 LT SOUR Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel AISI 316 LT Sour Stainl steel 6Mo LT Sour [A] Stainl steel 6Mo LT Sour [A] Stainl steel 6Mo LT Sour [A] Stainl steel 6Mo LT Sour [A] Stainl steel 6Mo LT Sour [A] Duplex stainless steel DUPLEX UNS S31803 3 3 3 3 3 3 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1500 2500 900 900 1500 1500 2500 2500 900 1500 2500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 150 300 300 600 600 900 900 1500 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 1500 150 300 600 900 150 150 150 BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS CC CC CA CA CC BS BS B B C B B A B A O O O C C C C B O O O O O B B B C A O O O O O D C C B D C D C C B C C C C B O O O O O C C C C B O O O O O O O O O O C B Page 3 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 01/2000 01/2000 01/2000 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2000 Headings 3 3 6 6 9 9 15 15 25 25 1 1 3 3 6 6 9 9 15 15 25 25 1 1 3 3 6 6 9 9 15 15 25 25 1 1 3 3 6 6 9 9 15 15 25 25 1 6 9 1 25 1 3 6 9 1 1 3831 3831 3831 3831 3831 3831 3831 3831 3831 3831 3832 3832 3832 3832 3832 3832 3832 3832 3832 3832 3832 3832 3833 3833 3833 3833 3833 3833 3833 3833 3833 3833 3833 3833 3834 3834 3834 3834 3834 3834 3834 3834 3834 3834 3834 3834 6410 6520 6520 6560 6560 6620 6620 6620 6620 8410 8420 Duplex stainless steel DUPLEX UNS S31803 Duplex stainless steel DUPLEX UNS S31803 Duplex stainless steel DUPLEX UNS S31803 Duplex stainless steel DUPLEX UNS S31803 Duplex stainless steel DUPLEX UNS S31803 Duplex stainless steel Sour DUPLEX UNS S31803 SOUR Duplex stainless steel Sour DUPLEX UNS S31803 SOUR Duplex stainless steel Sour DUPLEX UNS S31803 SOUR Duplex stainless steel Sour DUPLEX UNS S31803 SOUR Duplex stainless steel Sour DUPLEX UNS S31803 SOUR Duplex stainless steel Sour DUPLEX UNS S31803 SOUR Duplex stainless steel LT DUPLEX UNS S31803 LT Duplex stainless steel LT DUPLEX UNS S31803 LT Duplex stainless steel LT DUPLEX UNS S31803 LT Duplex stainless steel LT DUPLEX UNS S31803 LT Duplex stainless steel LT DUPLEX UNS S31803 LT Duplex stainless steel LT DUPLEX UNS S31803 LT Duplex stainless steel LT Sour DUPLEX UNS S31803 LT SOUR Duplex stainless steel LT Sour DUPLEX UNS S31803 LT SOUR Duplex stainless steel LT Sour DUPLEX UNS S31803 LT SOUR Duplex stainless steel LT Sour DUPLEX UNS S31803 LT SOUR Duplex stainless steel LT Sour DUPLEX UNS S31803 LT SOUR Duplex stainless steel LT Sour DUPLEX UNS S31803 LT SOUR Titanium Alloy 625 LT Sour [A] Alloy 625 LT Sour [A] Alloy 625 LT Sour Alloy 625 LT Sour Alloy 825 LT Sour [A] Alloy 825 LT Sour [A] Alloy 825 LT Sour [A] Alloy 825 LT Sour [A] CARBON STEEL GALVANISED CARBON STEEL GALVANISED 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 300 300 600 600 900 900 1500 1500 2500 2500 150 150 300 300 600 600 900 900 1500 1500 2500 2500 150 150 300 300 600 600 900 900 1500 1500 2500 2500 150 150 300 300 600 600 900 900 1500 1500 2500 2500 150 600 900 150 2500 150 300 600 900 150 150 BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS BS ET CA CA CB BS CB CB CA CA EB EB C B C B C B C B C B C B C B C B C B C B C B C B C B C B C B C B C B C B C B C B C B C B C B B O O O O O O O O B B Page 4 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2000 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 01/2006 12/1998 12/1998 Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev Rev 1 1 1 1 1 1 1 1 1 3 3 3 3 3 3 3 3 3 3 6 6 6 6 6 6 6 6 6 9 9 9 9 9 9 9 9 9 15 15 15 15 1440 1441 1450 1460 3430 3831 3832 3833 3834 1440 1441 1450 1451 1460 3430 3831 3832 3833 3834 1440 1441 1450 1460 3430 3831 3832 3833 3834 1440 1441 1450 1460 3430 3831 3832 3833 3834 3831 3832 3833 3834 Shname TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND TWND Apcode DN1 DN2 Printflag NF22 Y NF22 Y NF22 Y NF22 Y NF22 Y DS31 Y DS31 Y DS31 Y DS31 Y NF22 Y NF22 Y NF22 Y NF22 Y NF22 Y NF22 Y DS31 Y DS31 Y DS31 Y DS31 Y NF22 Y NF22 Y NF22 Y NF22 Y NF22 Y DS31 Y DS31 Y DS31 Y DS31 Y NF22 Y NF22 Y NF22 Y NF22 Y NF22 Y DS31 Y DS31 Y DS31 Y DS31 Y DS31 Y DS31 Y DS31 Y DS31 Y Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed Changed CLASSNO 11410 11410 11410 11410 11410 11420 11420 11420 11420 11420 11430 11430 11430 11430 11430 11440 11440 11440 11440 11440 11441 11441 11441 11441 11441 11450 11450 11450 11450 11450 11450 11450 11460 11460 11460 11460 11460 11460 11460 11470 11470 11470 11470 11470 11470 11480 11480 11480 11480 11480 11480 11490 11490 11490 11490 11490 11490 11500 11500 11500 11500 11500 TEMP 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 150 200 0 50 75 100 120 150 200 -50 0 50 75 100 120 -50 0 50 75 100 120 -50 0 50 75 100 120 -50 0 50 75 100 LIMIT 19.6 19.2 18.4 17.6 16.9 19.6 19.2 18.4 17.6 16.9 19.6 19.2 18.4 17.6 16.9 19.6 19.2 18.4 17.6 16.9 19.6 19.2 18.4 17.6 16.9 19.6 19.2 18.4 17.6 16.9 15.8 13.9 19.6 19.2 18.4 17.6 16.9 15.8 13.9 18.2 18.2 18.0 17.5 17.0 16.5 18.2 18.2 18.0 17.5 17.0 16.5 18.2 18.2 18.0 17.5 17.0 16.5 18.2 18.2 18.0 17.5 17.0 11500 11501 11501 11501 11501 11501 11501 13410 13410 13410 13410 13410 13410 13420 13420 13420 13420 13420 13420 13430 13430 13430 13430 13430 13430 13430 13430 13450 13450 13450 13450 13450 13450 13460 13460 13460 13460 13460 13460 13831 13831 13831 13831 13831 13831 13832 13832 13832 13832 13832 13832 13833 13833 13833 13833 13833 13833 13834 13834 13834 13834 13834 13834 120 -50 0 50 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 150 200 -100 0 50 75 100 120 -73 0 50 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 -50 0 50 75 100 120 -50 0 50 75 100 120 16.5 18.2 18.2 18.0 17.5 17.0 16.5 18.9 18.9 18.3 17.1 16.0 15.5 18.9 18.9 18.3 17.1 16.0 15.5 18.9 18.9 18.3 17.1 16.0 15.5 14.7 13.5 18.9 18.9 18.3 17.1 16.0 15.5 18.9 18.9 18.3 17.1 16.0 15.5 19.9 19.9 19.5 18.6 17.6 16.9 19.9 19.9 19.5 18.6 17.6 16.9 19.9 19.9 19.5 18.6 17.6 16.9 19.9 19.9 19.5 18.6 17.6 16.9 151410 151410 151410 151410 151410 151420 151420 151430 151430 151430 151430 151430 151440 151440 151441 151441 151450 151450 151450 151450 151450 151450 151450 151460 151460 151460 151470 151470 151470 151470 151470 151470 151480 151480 151480 151480 151490 151490 151490 151490 151490 151490 151500 151500 151500 151500 151501 151501 151501 151501 151520 151520 151521 151521 153410 153410 153410 153410 153410 153410 153410 153410 153410 0 50 75 100 120 0 120 0 50 75 100 120 0 120 0 120 0 50 75 100 120 150 200 0 150 200 -50 0 50 75 100 120 -50 75 100 120 -50 0 50 75 100 120 -50 75 100 120 -50 75 100 120 0 120 0 120 -20 0 50 75 100 120 -20 0 50 254.2 250.4 240.2 231.9 229.5 222.3 222.3 252.4 250.4 240.2 231.9 229.5 222.3 222.3 222.3 222.3 254.2 250.4 240.2 231.9 229.5 226.0 219.1 222.3 222.3 218.8 239.2 239.2 236.3 230.4 225.4 223.1 222.3 222.3 222.1 221.2 239.2 239.2 236.3 230.4 225.4 223.1 222.3 222.3 222.1 221.2 222.3 222.3 222.1 221.2 222.3 222.3 222.3 222.3 248.2 248.2 240.5 224.8 210.9 203.4 236.6 236.6 236.6 153410 153410 153410 153410 153410 153410 153410 153410 153410 153420 153420 153420 153420 153420 153420 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153430 153450 153450 153450 153450 153450 153450 153450 153450 153450 153450 153450 153450 153460 153460 153460 153460 153460 153460 153831 153831 153831 153831 153831 153831 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 150 200 -20 0 50 75 100 120 150 200 -20 0 50 75 100 120 150 200 -100 0 50 75 100 120 -100 0 50 75 100 120 -73 0 50 75 100 120 -20 0 50 75 100 120 224.8 210.9 203.4 228.4 228.4 228.4 224.8 210.9 203.4 222.3 222.3 220.4 216.3 210.9 203.4 248.2 248.2 240.5 224.8 210.9 203.4 192.4 178.4 236.6 236.6 236.6 224.8 210.9 203.4 192.4 178.4 228.4 228.4 228.4 224.8 210.9 203.4 192.4 178.4 248.2 248.2 240.5 224.8 210.9 203.4 236.6 236.6 236.6 224.8 210.9 203.4 222.3 222.3 220.4 216.3 210.9 203.4 258.5 258.5 256.2 251.6 245.9 239.1 153832 153832 153833 153833 153833 153833 153833 153834 153834 16410 16410 18410 18410 18420 18420 251410 251410 251410 251410 251410 251420 251420 251430 251430 251430 251430 251430 251440 251440 251440 251440 251441 251441 251441 251441 251520 251520 251520 251520 251521 251521 251521 251521 253831 253831 253831 253831 253831 253832 253832 253833 253833 253833 253833 253833 253834 253834 31410 31410 31410 31410 31410 31411 -20 120 -50 50 75 100 120 -50 120 0 50 0 60 0 60 0 50 75 100 120 0 120 0 50 75 100 120 0 120 0 120 0 120 0 120 0 120 0 120 0 120 0 120 -20 50 75 100 120 -20 120 -50 50 75 100 120 -50 120 0 50 75 100 120 0 222.3 222.3 253.9 253.9 251.6 245.9 239.1 222.3 222.3 18.9 18.4 15.5 15.5 7.0 7.0 425.4 417.1 400.2 386.5 382.7 308.8 308.8 425.4 417.1 400.2 386.5 382.7 308.8 308.8 278.4 278.4 308.8 308.8 278.4 278.4 308.8 308.8 278.4 278.4 308.8 308.8 278.4 278.4 425.0 425.0 419.3 409.8 398.4 308.8 308.8 425.0 425.0 419.3 409.8 398.4 308.8 308.8 50.1 50.0 48.0 46.3 45.8 50.8 31411 31411 31411 31411 31411 31411 31411 31411 31411 31420 31420 31420 31420 31420 31430 31430 31430 31430 31430 31440 31440 31440 31440 31440 31441 31441 31441 31441 31441 31450 31450 31450 31450 31450 31450 31450 31451 31451 31451 31451 31451 31451 31451 31451 31451 31451 31451 31451 31451 31451 31460 31460 31460 31460 31460 31460 31460 31470 31470 31470 31470 31470 31470 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 150 200 0 50 75 100 120 150 200 0 50 75 100 120 150 200 0 50 75 100 120 150 200 -50 0 50 75 100 120 50.0 48.0 46.3 45.8 42.9 42.9 42.9 42.9 42.9 50.5 50.0 48.0 46.3 45.8 51.0 50.0 48.0 46.3 45.8 51.0 50.0 48.0 46.3 45.8 51.0 50.0 48.0 46.3 45.8 50.1 50.0 48.0 46.3 45.8 45.1 43.8 50.8 50.0 48.0 46.3 45.8 45.1 43.8 42.9 42.9 42.9 42.9 42.9 42.9 42.9 50.5 50.0 48.0 46.3 45.8 45.1 43.8 47.9 47.9 47.3 46.0 45.0 44.6 31480 31480 31480 31480 31480 31480 31490 31490 31490 31490 31490 31490 31500 31500 31500 31500 31500 31500 31501 31501 31501 31501 31501 31501 33410 33410 33410 33410 33410 33410 33420 33420 33420 33420 33420 33420 33430 33430 33430 33430 33430 33430 33430 33430 33450 33450 33450 33450 33450 33450 33460 33460 33460 33460 33460 33460 33831 33831 33831 33831 33831 33831 33832 -50 0 50 75 100 120 -50 0 50 75 100 120 -50 0 50 75 100 120 -50 0 50 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 150 200 -100 0 50 75 100 120 -73 0 50 75 100 120 -20 0 50 75 100 120 -20 47.9 47.9 47.3 46.0 45.0 44.6 47.9 47.9 47.3 46.0 45.0 44.6 47.9 47.9 47.3 46.0 45.0 44.6 47.9 47.9 47.3 46.0 45.0 44.6 49.6 49.6 48.1 45.0 42.2 40.7 49.6 49.6 48.1 45.0 42.2 40.7 49.6 49.6 48.1 45.0 42.2 40.7 38.5 35.7 49.6 49.6 48.1 45.0 42.2 40.7 49.6 49.6 48.1 45.0 42.2 40.7 51.7 51.7 51.2 50.3 49.1 47.8 51.7 33832 33832 33832 33832 33832 33833 33833 33833 33833 33833 33833 33834 33834 33834 33834 33834 33834 61410 61410 61410 61410 61410 61420 61420 61420 61420 61420 61430 61430 61430 61430 61430 61440 61440 61440 61440 61440 61441 61441 61441 61441 61441 61450 61450 61450 61450 61450 61450 61450 61460 61460 61460 61460 61460 61460 61460 61470 61470 61470 61470 61470 61470 61480 0 50 75 100 120 -50 0 50 75 100 120 -50 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 0 50 75 100 120 150 200 0 50 75 100 120 150 200 -50 0 50 75 100 120 -50 51.7 51.2 50.3 49.1 47.8 51.7 51.7 51.2 50.3 49.1 47.8 51.7 51.7 51.2 50.3 49.1 47.8 102.0 100.0 96.0 92.7 91.9 99.1 97.7 95.0 92.7 91.9 102.0 100.0 96.0 92.7 91.9 99.1 97.7 95.0 92.7 91.9 99.1 97.7 95.0 92.7 91.9 102.0 100.0 96.0 92.7 91.9 90.6 87.8 99.1 97.7 95.0 92.7 91.9 90.6 87.8 95.8 95.8 94.7 92.3 90.3 89.3 95.8 61480 61480 61480 61480 61480 61490 61490 61490 61490 61490 61490 61500 61500 61500 61500 61500 61500 61501 61501 61501 61501 61501 61501 63410 63410 63410 63410 63410 63410 63420 63420 63420 63420 63420 63420 63430 63430 63430 63430 63430 63430 63430 63430 63450 63450 63450 63450 63450 63450 63460 63460 63460 63460 63460 63460 63831 63831 63831 63831 63831 63831 63832 63832 0 50 75 100 120 -50 0 50 75 100 120 -50 0 50 75 100 120 -50 0 50 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 150 200 -100 0 50 75 100 120 -73 0 50 75 100 120 -20 0 50 75 100 120 -20 75 95.8 94.7 92.3 90.3 89.3 95.8 95.8 94.7 92.3 90.3 89.3 95.8 95.8 94.7 92.3 90.3 89.3 95.8 95.8 94.7 92.3 90.3 89.3 99.2 99.2 96.2 90.0 84.5 81.5 99.1 99.1 96.1 89.9 84.5 81.5 99.2 99.2 96.2 90.0 84.5 81.5 77.0 71.1 99.2 99.2 96.2 90.0 84.5 81.5 99.1 99.1 96.1 89.9 84.5 81.5 103.4 103.4 102.5 100.6 98.3 95.6 99.1 99.1 63832 63832 63833 63833 63833 63833 63833 63833 63834 63834 63834 63834 91410 91410 91410 91410 91410 91420 91420 91420 91420 91430 91430 91430 91430 91430 91440 91440 91440 91440 91441 91441 91441 91441 91450 91450 91450 91450 91450 91450 91450 91460 91460 91460 91460 91460 91460 91470 91470 91470 91470 91470 91470 91480 91480 91480 91480 91480 91480 91490 91490 91490 91490 100 120 -50 0 50 75 100 120 -50 75 100 120 0 50 75 100 120 0 75 100 120 0 50 75 100 120 0 75 100 120 0 75 100 120 0 50 75 100 120 150 200 0 75 100 120 150 200 -50 0 50 75 100 120 -50 0 50 75 100 120 -50 0 50 75 98.1 95.1 103.4 103.4 102.5 100.6 98.3 95.6 99.1 99.1 98.1 95.1 153.0 150.1 144.0 139.1 137.8 137.5 137.5 137.3 136.7 153.0 150.1 144.0 139.1 137.8 137.5 137.5 137.3 136.7 137.5 137.5 137.3 136.7 153.0 150.1 144.0 139.1 137.8 135.7 131.3 137.5 137.5 137.3 136.7 135.7 131.3 143.7 143.7 142.0 138.4 135.3 134.0 137.5 137.5 137.1 136.3 135.3 134.0 143.7 143.7 142.0 138.4 91490 91490 91500 91500 91500 91500 91500 91500 91501 91501 91501 91501 91501 91501 91520 91520 91520 91520 91521 91521 91521 91521 93410 93410 93410 93410 93410 93410 93420 93420 93420 93420 93420 93420 93430 93430 93430 93430 93430 93430 93430 93430 93450 93450 93450 93450 93450 93450 93460 93460 93460 93460 93460 93460 93831 93831 93831 93831 93832 93832 93833 93833 93833 100 120 -50 0 50 75 100 120 -50 0 50 75 100 120 0 75 100 120 0 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 -20 0 50 75 100 120 150 200 -100 0 50 75 100 120 -73 0 50 75 100 120 -20 75 100 120 -20 120 -50 50 75 135.3 134.0 137.5 137.5 137.1 136.3 135.3 134.0 137.5 137.5 137.1 136.3 135.3 134.0 137.5 137.5 137.3 136.7 137.5 137.5 137.3 136.7 148.9 148.9 144.3 135.0 126.7 122.2 137.5 137.5 135.4 131.3 126.7 122.2 148.9 148.9 144.3 135.0 126.7 122.2 115.6 106.9 148.9 148.9 144.3 135.0 126.7 122.2 137.5 137.5 135.4 131.3 126.7 122.2 155.1 155.1 154.5 152.9 137.5 137.5 152.7 152.7 150.9 93833 93833 93834 93834 100 120 -50 120 147.5 143.4 137.5 137.5 CLASSNO 11410 11420 11430 11440 11441 11450 11460 11470 11480 11490 11500 11501 13410 13420 13430 13450 13460 13831 13832 13833 13834 16410 18410 18420 31410 31411 31411 31420 31430 31440 31441 31450 31451 31451 31460 31470 31480 31490 31500 31501 33410 33420 33430 33450 33460 33831 33832 33833 33834 61410 61420 61430 61440 61441 61450 61460 61470 61480 61490 61500 61501 63410 PIPEFROM 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 300 15 15 15 15 15 15 300 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 PIPEUNTIL 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 150 100 100 600 250 600 600 600 600 600 600 250 600 600 600 600 600 600 600 300 300 300 300 300 600 600 600 600 600 600 600 600 600 600 600 400 400 400 400 400 200 63420 63430 63450 63460 63831 63832 63833 63834 91410 91420 91430 91440 91441 91450 91460 91470 91480 91490 91500 91501 91520 91521 93410 93420 93430 93450 93460 93831 93832 93833 93834 151410 151420 151430 151440 151441 151450 151460 151470 151480 151490 151500 151501 151520 151521 153410 153410 153410 153420 153430 153430 153430 153450 153450 153460 153831 153832 153833 153834 251410 251420 251430 251440 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 150 200 15 15 150 200 15 150 15 15 15 15 15 15 15 15 15 200 200 200 200 600 600 600 600 600 600 600 600 600 600 600 400 400 400 400 400 400 400 200 200 200 200 200 600 600 400 400 600 600 600 600 600 600 600 400 400 400 400 400 400 400 100 150 200 200 100 150 200 100 150 150 400 500 250 250 300 300 300 100 251440 251441 251441 251520 251520 251521 251521 253831 253832 253833 253834 150 15 150 15 150 15 150 15 15 15 15 300 100 300 100 300 100 300 150 300 150 150

Piping-classes-exploration-and-production

Products

Support

Piping-classes-exploration-and-production

Add this document to collection(s)

Add this document to saved

Suggest us how to improve StudyLib