ParameterID
Parameter Name
BfMimoAdaptiveSwitch
BfMIMO adaptive switch
SPECIALSUBFRAMEPATTERNS
Special subframe patterns
SSP6DWPTSMODE
SSP6 DwPTS Mode
BFALGOSWITCH
BF algorithm switch
PucchAlgoSwitch
PUCCH algorithm switch
MAXBFRANKPARA
Beamforming maximum number of layers
ASUEDUALBFTOTM3RANK2OFFSET
AS UE Dual BF To TM3 Rank2 Offset
BFMIMOADAPWITHOUTTM2
Bf Mimo Adaptive Without Tm2
TM3RANK2TODUALBFTHDOFFSET
TM3 Rank2 To Dual Streaming Beamforming
Threshold Offset
UlIblerOptSwitch
Uplink Ibler Optimization Switch
CQIADJSTEP
CQI Adjust Step
INITDELTACQI
Initial Delta Cqi
INITDLIBLERTARGET
Initial Downlink IBLER Target
PUSCHPsdCtrlTarget
PUSCH PSD Control Target
PDCCHSYMNUMSWITCH
PDCCH Symbol Number Adjust Switch
SMARTPREALLOCATIONDURATION
Smart pre-allocation duration
SriFalseDetThdSwitch
Sri False Detect Threshold Switch
UESRSANTSELECTCTRLSWITCH
UE SRS Antenna Selection Control Switch
ADAPTIVESTEPVARYSWITCH
Adaptive variable step algorithm switch
BUNDLINGOPTTHDSWITCH
Bundling optimization threshold switches
CFICONVERTOPTSWITCH
CFI Conversion Optimization Switch
DLVARIBLERTARGETSWITCH
Downlink variable BLER Target Switch
TDDBUNDLINGCQIADJOPTSWITCH
TDD Bundling CQI Adjustment switch
TDDMULTIPLEXINGCQIADJOPTSWITCH
TDD Multiplexing CQI adjustment Optimization
switch
DETECTRANK2ADJSWITCH
Dl Rank Detect Switch
TDDACKFBMODECFGOPTSWITCH
TDD HARQ-ACK feedback Optimization Switch
BASEDSRIGAPOPTSWITCH
SRI Gap Optimization Switch
DRXBASEDSRIGAPOPTSWITCH
DRX Based Gap Optimization Switch
GAPPATTERNTYPE
GAP measurement pattern
IntraFreqHoA3Hyst
Intrafreq handover hysteresis
INITPDCCHSYMNUM
PDCCH Initial Symbol Number
SMARTPREALLOCATIONSWITCH
Smart Pre-allocation Switch
SchedulerCtrlPowerSwitch
Scheduler control power switch
ULFSSAlgoswitch
Uplink frequency-selective switch
PrachRbReuseSwitch
PUSCH and PUCCH resource Multiplexing Switch
Remarks
It should "2" (MIMO_BF_ADAPTIVE)
(Beam Forming & MIMO should be in use )
No impact on Impact on Radio Network Performance
No impact on Impact on Radio Network Performance
No direct impact but "BfMIMO adaptive switch" is valid only when BfSwitch is
selected. So this switch should be ON.
(Beam Forming should be in use)
This parameter should be "ON"
It should be "DUAL_LAYER_BF"
(Beam Forming should be in use)
This parameter should be 35
(Beam Forming should be in use)
It should be "ON"
(Beam Forming should be in use)
This parameter should be 35
(Beam Forming should be in use)
Trail should be done with value "ON" in a in a cluster
Huawei recommended valus is 10 but trail should be done in a small cluster
with value=30 & 50
Huawei recommended valus is -4 but trail should be done in a small cluster
with value=0
Huawei recommended valus is 10 but trail should be done in a small cluster
with value=15
It should be 8
It should be "ON"
It should be "50"
(SmartPreAllocationSwitch is set to On)
Huawei recommended valus to "OFF" but trail can be done with "ON"
It should be "ON"
Huawei recommended value is "OFF" but if this is "ON", the CQI adjustment is
performed at a large step in case of significant signal quality changes,
accelerating the IBLER convergence and therefore increasing the downlink
throughput. So trial is recomended in a cluster with "ON" setting.
Huawei recomende value is "OFF" though throughput can increase as this
could lead to increase drop. But trail can be done to see the impact with "ON".
Huawei recomende value is "OFF" though throughput can increase as this
could lead to increase drop. But trail can be done to see the impact with "ON".
It should be "ON"
It should be "ON"
It should be "ON"
It should be "ON"
Huawei recomende value is "OFF" though throughput can increase as this
could lead to increase drop and poor HO success rate. But trail can be done to
see the impact with "ON".
This should be "ON"
This should be "ON"
This should be "GAP_PATTERN_TYPE_2"
Trial should be done with "4 dB"
This should be "1"
It should be "ON"
This should be "ON" for medium and light loaded cells
It should be "OFF"
It should be "ON"