Gas Technician III Learning Package Module 1 – Safety: Protecting Yourself & Others Contents Learning Outcomes: ....................................................................................................................... 3 Recognizing Hazardous Situations: ................................................................................................ 4 Eye Protection: ............................................................................................................................... 5 Body Protection: ............................................................................................................................ 6 Lifting and Material Handling: ....................................................................................................... 7 Respiratory Protection: .................................................................................................................. 8 Hearing Protection: ........................................................................................................................ 9 Ladder Safety: .............................................................................................................................. 10 Locking-Out of Equipment: .......................................................................................................... 11 Confined Space Entry: .................................................................................................................. 13 Fire Hazard Awareness ................................................................................................................ 16 Occupational Health & Safety Act: .............................................................................................. 19 Workplace Hazardous Materials Information System ................................................................. 21 For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 2 It is essential in our trade as Gas Technicians that we Learning Outcomes: familiarize ourselves with potential safety hazards. We must ensure that we are equipped with the necessary tools, equipment, codes, and technical literature required to do our job safely. After completion of this module you will be able to: Recognize hazardous work situations. Identify personal and general safety equipment and understand its purpose. State safe manual lifting procedures to help reduce back injuries. List rules for safe handling of ladders. Identify the purpose, methods, and equipment associated with locking-out mechanical and electrical energy sources. Recognize hazards, atmospheric testing requirements, safety equipment, and Occupational Health and Safety Act Regulation requirements associated with working in confined spaces such as a boiler or tank. Identify fire hazards, classes of fires, and fire extinguishing equipment. Identify your rights and responsibilities, as well as the rights and responsibilities of your employer and others, as set out in health and safety legislation. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 3 Recognizing Hazardous Situations: Injuries are often caused because we do not follow known safety precautions. Always take the time to get the proper tool, wear the proper personal protective device, and follow known safety procedures. Your safety, and the safety of others, depends on it. Reduce potential hazards. Keep your work area free and clear of debris, trash, scrap, spills, and other materials which could cause an accident. Properly label and store hazardous materials. Remove loose clothing, jewelry, and tie back long hair when working on equipment. Always have ample light in your work area. Do not sacrifice your safety or the safety of others by cutting corners or rushing in order to meet deadlines. The Workplace Safety and Insurance Act. The Workplace Safety and Insurance Act contains Ontario workplace safety requirements relating to workplace injuries and first aid. The Act spells out requirements for first aid stations, the prompt treatment of injured workers, the Figure 1-1 First Aid Kit reporting of accidents, and advice given to an injured worker. Every employer is required to post a notice (Form 82) indicating the necessity for employees to report accidents. It is your responsibility to report an accident or injury, unsafe or unhealthy working conditions, should they occur. Further Study - View Workplace Safety and Insurance Act - First Aid Requirements. Web site: www.wsib.on.ca For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 4 Protect your eyesight. Flying debris from tool use, pipe Eye Protection: threading, ventilation systems, and splashes of toxic or corrosive chemicals are just a few potential hazards to your eyesight. Do not risk serious eye injury. Select the proper eyewear for the task you are undertaking. There are three basic types of eye protection devices: Face-Shields offer full-face protection. They have a band across the brow and one or two bands that cross over the top or around Figure 1-2 Face Shield the back of the head. Face shields are used in situations where the entire face needs protection and should be worn to protect your eyes and face against flying particles, metal sparks, and chemical splashes. Safety Goggles fit tightly around the eyes. They provide eye Figure 1-3 Goggles protection from the front, bottom, top and sides. There are models available that can fit over your prescription glasses. Safety Glasses are open at the top and bottom. They usually have side shields that offer side impact protection. Some models include a Figure 1-4 Safety Glasses brow protection rim at the top. The lenses are made of safety glass or plastic and the frames are made of plastic or metal. Note: The brilliant light given off by a welder's arc contains a high proportion of ultra-violet radiation, which can damage your eyes, even after momentary exposure. If welding is taking place in an area you are Figure 1-5 Welding Goggles working in, remember not to look at the spark. The welder should use adequate screening to protect nearby workers. Further Study - View Occupational Health and Safety Act References Relating to Eye Protection: http://www.e-laws.gov.on.ca/ For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 5 Protect your body from musculoskeletal force, extreme hot or cold temperatures, and repeated impacts. Body Protection: Wear proper equipment to protect your hands, feet, head and knees. Be aware of workplace physical hazards. Gloves provide your hands with protection against sharp appliance edges, sheet metal, gas piping edges, absorption of harmful substances, and hot surfaces. Gloves should be chosen based on the type of material being handled, the particular hazard involved, and the suitability of the gloves for the job Figure 1-6 Protective Gloves you are doing. One type of glove will not necessarily provide adequate protection in all situations. Kneepads protect your knees from stress and pressure and are ideal Figure 1-7 Knee Pads for jobs that require extended periods of kneeling on hard surfaces. Wear appropriate, CSA approved safety footwear whenever you will be exposed to the hazard of foot injury. A variety of approved safety Figure 1-8 Work Boots footwear is available with features such as protective steel toes, and outsoles that are resistant to heat, oil, acid, punctures and accidental Figure 1-9 Hard Hat electrical contact. Hard hats will offer protection against falling objects as well as bump hazards associated with confined spaces. Both you and your employer have legal responsibilities regarding protective safety equipment. You must wear the protective clothing, equipment, or device required by your employer. The Occupational Health and Safety Act (OHSA) specifies that where you are required to wear or use any protective clothing, equipment, or device, you shall be instructed and trained in its care and use before wearing or using it. Further Study - View Occupational Health and Safety Act references relating to Body Protection: http://www.e-laws.gov.on.ca/ For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 6 Lifting and Material Handling: Proper posture and body mechanics can help to protect your body, especially your back, from pain and injury. Below are some guidelines on how to lift properly to help protect your back from injury. Only lift loads that you can safely handle. Figure 1-10 Knees bent, get close to object Get as close as possible to the object. Keep your knees bent as you grab the object. Keep your back straight. Have a good hold on the object. Lift by using your legs. Figure 1-11 Use your legs to lift Keep the object close to your body while lifting. Avoid fast movements during a lift. Avoid twisting at the waist. Pivot feet while turning. Follow the above tips when putting object down. Figure 1-12 Keep object close Get assistance when the load is too heavy. Figure 1-13 Avoid twisting at waist For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 7 The proper mask or respirator will provide protection Respiratory Protection: from numerous harmful dusts, mists, fumes, vapours and other pollutants. They include disposable dust masks (Figure 1-14), half-face respirator masks (Figure 1-15), and full-face respirator masks (Figure 1-16). The half and full-face respirators use interchangeable filter cartridges. *You must ensure that you select the proper mask and/or filter cartridge for the particular hazard you may be exposed to. Figure 1-15 North 5500 Half-Face Respirator Figure 1-14 Dust Mask Figure 1-16 North FullFace Respirator Manufacturers usually colour code respirator filters to match a particular hazard. The filters on the North 5500 half face mask (Figure 1-15) are equipped with North 7580P100 filters, which are commonly used in our trade for nuisance dusts, mists and fumes. The filters are replaceable and this mask generally provides a tighter fit than disposable Figure 1-17 Colour coded respirator filters dust masks. You should always use filters on the mask the filters were designed for. Do not combine one manufacturer's mask with another manufacturer's filters. Further Study - View Occupational Health and Safety Act references relating to Respiratory Protection and Equipment: http://www.e-laws.gov.on.ca/. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 8 Hearing Protection: Do not risk permanent hearing loss. Select the proper hearing protection for the task you are undertaking. Noise is measured in decibels (db). The louder the noise, the higher the decibel rating. A normal conversation is approximately 60db whereas a circular power saw may reach 120 db. Most experts say 85 db is the safe maximum noise level for human ears. Power tools, mechanical equipment, or simply hammering on metal are noises that can exceed a safe decibel level. Earplugs offer good, inexpensive hearing protection. Foam earplugs are rolled between the fingers to decrease their diameter, and then inserted into the ear canal where the foam expands to conform to Figure 1-18 Foam earplugs the size of the ear canal. Because earplugs are inserted directly into the ear, it is important to keep them clean and replace them often. Earplugs are generally considered to be disposable. Earmuffs protect your hearing from outside of the ear. They are more expensive than earplugs but they last much longer. Earmuffs are easier to keep clean, and are less likely to be misplaced. Most earmuffs have a fixed level of noise blocking. Figure 1-19 Earmuffs Further Study - View Occupational Health and Safety Act references relating to Hearing Protection http://www.e-laws.gov.on.ca/ . For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 9 Ladders are a useful and a necessary tool. Because Ladder Safety: ladders are so commonplace, safety precautions are often taken for granted. Falls from ladders can result in serious injuries and death. Always inspect your ladder before using it. Ensure all rungs and steps are dry and free of dirt, oil, or other slip hazards. Check that all locking devices are secure, nonskid feet at bottom of ladder are in place, and that there are no structural defects. Remember the 4 to 1 ladder positioning rule. For example, if you were placing an extension ladder against a wall, the base of the ladder should Figure 1-20 Nonskid Feet be 1 foot out from the wall for every 4 feet that the ladder extends up the wall. Although the same rule would apply if you were placing the ladder against a building, the top of the ladder should also extend 3 feet above top of the roof. Do not use broken ladders. Most ladders cannot be repaired to manufacturer specifications and should be replaced if broken. Figure 1-22 Step Ladder Figure 1-21 Extension Ladders Further Study - View Occupational Health and Safety Act references relating to Ladder Safety http://www.e-laws.gov.on.ca/ For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 10 Locking-Out of Equipment: The term “zero mechanical state” is used to describe a state where the mechanical potential energy of all portions of a piece of equipment or machinery is set to ensure that a movement will not cause injury. Some examples include: the opening of pipes, tubes, hoses, or actuation of any valve, lever or button. Do not risk injury by the accidental starting of equipment that you are working on. You must ensure that machines and equipment are isolated from potentially hazardous energy. Whether it is steam, electrical, mechanical, hydraulic, or gas, you must lockout and tag anytime unexpected start-up could cause personal injury, fire, or equipment damage. Simply switching off the electrical power or turning off a valve to a piece of equipment you are working on is not a positive means of ensuring the equipment will not be accidentally reactivated. The equipment we work on is often connected to many energy sources. Whether you are working on a blower Figure 1-23 Locked out Electrical Disconnect Switch and Tag motor from a furnace or fuel burner, replacing an electrical or mechanical component or just performing a routine inspection, you must ensure that all sources of mechanical and electrical energy are isolated from the equipment so it cannot be accidentally activated. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 11 Figure 1-24 Locked Out Electrical Toggle Switch A lockout device including a padlock should be placed on the energy isolating device of a piece of equipment, machinery or system such as gas valves, steam and water valves, electrical disconnect switches and boxes. Figure 1-25 shows a gate valve being locked out. Figure 1- 26 shows a gas valve being locked out. Figure 1-25 Gate Valve on Water Supply Locked Out Figure 1-26 Locked out Ball Valve on Natural Gas Supply Line The placement of lockout devices is done to ensure that the equipment cannot be operated until the lock out device is removed. You should have your own locks that can only be removed by you at the completion of the job. During lockouts by multiple personnel, the equipment, machinery or system must remain secured until the last authorized or affected person has completed his or her work and has removed his or her lock. Figure 1-27 Multi Lockout Bar Figure 1-28 Personal Lock Further Study - View Occupational Health and Safety Act references relating to Locking Out of Equipment: http://www.e-laws.gov.on.ca/ . For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 12 Confined Space Entry: A confined space is an area that is normally not designated or intended for human occupancy. Confined spaces usually have limited means of access and exit with little or no natural ventilation. Confined spaces generally have poor ventilation and could contain a hazardous atmosphere or have the potential of containing a hazardous atmosphere. Consequently, special precautions are required to ensure your protection prior to entering and while working in a confined space. Figure 1-29 Confined Space - Tank Figure 1-30 Portable fan for confined space ventilation Some examples of confined spaces are: Boilers. Ventilation ducts. Tanks. Pits. Tunnels. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 13 There are many hazards associated with working in a confined space including: Oxygen deficient atmospheres. flammable atmospheres toxic atmospheres engulfing dangers electrical shock hazards mechanical grinding dangers crushing and mixing hazards drowning hazards chemical hazards Our work can often require us to enter and work within the confined space of boilers, and tanks. A typical commercial boiler, for example, is connected to many potentially hazardous energy sources such as: natural gas lines, oil lines, pressurized steam, and hot water lines Many boilers share venting with other boilers or hot water heaters. Additionally, there is often more than one electrical source to consider. Figure 1-31 Confined Space – Commercial Boiler For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 14 Imagine you are working inside a boiler that is connected to numerous potentially hazardous energy sources. While inside the boiler, you want to feel confident that all necessary safety precautions have been taken to ensure your safety. You do not want to wonder whether or not someone might inadvertently turn on a switch, starting the fuel burner, or if an unaware tradesperson will accidentally open a steam or hot water line, or if toxic combustion gases from other boilers or hot water tanks may be present in the boiler you are working in. Do not take chances. Where your employer requires you to work in boilers, tanks, pits, ventilation ducts, or any other confined space, you must be provided with proper confined space entry training including lockout and atmospheric testing procedures. Where you will be exposed to a falling hazard in a confined space, or other area, a lifeline and parachute harness is required. A suitable method of arresting a fall must also be used in conjunction with the lifeline and harness. Figure 1-33 Lifelines Figure 1-34 Fall Arrester Figure 1-32 Parachute Harness Further Study - View Occupational Health and Safety Act References relating Confined Space Entry http://www.e-laws.gov.on.ca/ For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 15 Fire Hazard Awareness: Oxygen, heat, and fuel are frequently referred to as the "fire triangle". Take any of these three things away, and you will not have a fire, or the fire will be extinguished. Essentially, fire extinguishers put out fire by taking away one or more elements of the fire triangle. Three things must be present at the same time in order to produce fire: 1. Enough oxygen to sustain combustion. 2. Enough heat to raise the material to its ignition temperature. 3. Some sort of fuel or combustible material. Figure 1-35 Combustion Triangle Fires are classified into four general categories depending on the type of material or fuel involved. The type of fire determines the type of extinguisher that should be used to extinguish it. Class A fires involve materials such as wood, paper, and cloth which produce glowing embers. Class B fires involve flammable gases, liquids, and greases, including gasoline and most hydrocarbon liquids which must be vaporized for combustion to occur. Class C fires involve live electrical equipment. Class D fires involve combustible metals. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 16 Extinguishers are selected according to the potential fire hazard, the construction and occupancy of facilities, hazard to be protected, and other factors pertinent to the situation. Different types of fire extinguishers are designed to fight different classes of fire. There are four Figure 1-36 Fire Extinguishers classes of fire extinguishers. The three most common types of fire extinguishers are air-pressurized water, carbon dioxide, and dry chemical. Air-pressurized water (APW) extinguishers are large, silver extinguishers, which are filled about two-thirds of the way with ordinary tap water, then pressurized with normal air. APWs are designed for Class A (wood, paper, cloth) fires only. Carbon Dioxide extinguishers are filled with nonflammable carbon dioxide gas under extreme pressure and are designed for Class B and C fires only. Dry Chemical Extinguishers come in a variety of types. You may see them labeled "ABC" indicating that they are designed to extinguish class A, B, and C fires, or "BC" indicating that they are designed to extinguish class B and C fires. Dry chemical extinguishers put out fire by coating the fuel with a thin layer of dust, separating the fuel from the oxygen in the air. The powder also works to interrupt the chemical reaction of fire, so these extinguishers are extremely effective at putting out fire. The Ontario Fire Code requires that portable extinguishers be inspected monthly and tested yearly. Reliable extinguishers bear the approval label of a recognized testing laboratory. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 17 It is easy to remember how to use a fire extinguisher if you can remember the acronym PASS, which stands for Pull, Aim, Squeeze, and Sweep. Pull the pin. This will allow you to discharge the extinguisher. Aim at the base of the fire. If you aim at the flames (which is frequently the temptation), the extinguishing agent will fly right through and do no good. You want to hit the fuel. Squeeze the top handle or lever. This depresses a button that releases the pressurized extinguishing agent in the extinguisher. Sweep from side to side until the fire is completely out. Start using the extinguisher from a safe distance away, then move forward. Once the fire is out, keep an eye on the area in case it reignites. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 18 The Occupational Health and Safety Act (OHSA) is Occupational Health & Safety Act: Law in Ontario. The purpose of the act is to protect workers from ill health, injury or death. It is administered by the Ontario Ministry of Labour and is applicable to almost all workers in Ontario. The legislation and the books are divided into two distinct sections, the Act and the Regulations. The Act: The Act is the enabling legislation for the regulations. Under the powers of the Act, regulations can be altered, explained, and or additional regulations can be issued without being passed through the Ontario Legislature. The Act contains the following information: Definitions of words and terms used in the Act. Exemptions from the Act. Powers of Minister, Deputy Ministers and Inspectors. Health and Safety Committees and their powers. Advisory Committees. Duties of Constructors, Employers, Supervisors, Workers, Owners, and Suppliers. Toxic Substances. Refusal to Work. Reporting of Accidents. Enforcement of the Regulations, Offences and Penalties. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 19 The Regulations: The Regulations are like "houses" built on the "foundation" of the Act. The regulations have been written to cover 3 distinct work environments. They are: Mining Construction, and Industrial Establishments Note: If construction is to be done in industrial establishments then the Regulations of the Construction section as well as those of the Industrial Section may need to be observed. It is also important to note the definition of “Competent Person” as it is defined in the Act. The term is used throughout the Act and Regulations, such as in the regulations involving confined space entry, where it states that a confined space must be evaluated by a “competent person”, or in the Act where it states that employers must appoint “competent persons” as supervisors. “Competent person” has a very specific meaning and to be competent a person must be: qualified through knowledge, training and experience to organize the work and its performance; be familiar with the Act and the regulations that apply to the work being performed in the workplace; know about any actual or potential danger to health and safety in the workplace. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 20 Workplace Hazardous Materials Information System The Workplace Hazardous Materials Information System (WHMIS), is a comprehensive plan for providing information on the safe use of hazardous materials in the workplace. As an employee, you are informed by means of product labels, Safety Data Sheets (SDS) and education programs. Figure 1-37 WHMIS System Respiratory or skin sensitization Biohazardous Infectious Corrosive Materials Acute toxicity Oral, Dermal, Inhalation Compressed Gas Flammable Material Oxidizing Material Severe, and acute toxicity Selfreactive substances Table 1-1 WHMIS 2015 - Pictograms Your employer is required to provide training whenever you could be exposed to hazardous products in your workplace. Employers must make sure products are properly labeled and that Safety Data Sheets (SDS) is readily available for each product. Both you and product suppliers have specified responsibilities under the Hazardous Products Act. For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 21 “WHMIS is implemented by complementary federal, provincial and territorial legislation and regulations. The main purpose of the federal WHMIS legislation is to require suppliers of hazardous products intended for use, handling or storage in a workplace to classify those products and provide health and safety information about them to their customers.” “The main purpose of the provincial and territorial WHMIS legislation is to require employers to obtain health and safety information about hazardous products from their suppliers, and to use that information to train their workers. In addition, confidential business information is protected under WHMIS” - © Queen’s Printer for Ontario, 2021 The WHMIS legislation - https://www.ontario.ca/document/workplace-hazardousmaterials-information-system-guide-legislation/whmis-legislation Under WHMIS 2015, there are key changes to the federal legislation: “Controlled Products are now called Hazardous Products. New rules and criteria for classifying hazardous chemicals improve the supplier's ability to indicate the severity of hazards. There are different hazard classes/categories and more of them. Supplier label requirements include new pictograms for hazard classes and prescribed hazard statements and signal words.” “Safety data sheets have a new, standardized 16-section format with prescribed information elements. Safety data sheets are required to be updated on an ongoing basis, as new information about a product becomes available. There is no longer a requirement to update a safety data sheet every three years. - © Queen’s Printer for Ontario, 2021” The WHMIS legislation - https://www.ontario.ca/document/workplace-hazardousmaterials-information-system-guide-legislation/whmis-legislation **End of Module - Return to Course and Complete Associated Online Test(s)** The following pages contain a SDS example (First 2 pages) of SDS for a commonly use gas pipe sealant (Masters Pro-Dope) https://www.oateycanada.com/uploads/files/SDS-CanadaMasters-Pro-Dope-Thread-Sealant.pdf For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 22 Masters Pro-Dope Oatey Version No: 1.5 Safety Data Sheet according to WHMIS 2015 requirements Issue Date: 12/16/2020 Print Date: 12/16/2020 S.GHS.CAN.EN SECTION 1 Identification Product Identifier Product name Synonyms Proper shipping name Other means of identification Masters Pro-Dope Not Available SOLIDS CONTAINING FLAMMABLE LIQUID, N.O.S. Isopropanol PD250BT, PD500BT, PD1L, PD 20L Recommended use of the chemical and restrictions on use Relevant identified uses Pipe Joint Compound for Threaded Metal Pipes Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party Registered company name Address Telephone Oatey 620 Steven Court, New Market, ON L3Y 622 Canada 905-898-2557 Fax Not Available Website Not Available Email info@oatey.com Emergency phone number Association / Organisation Emergency telephone numbers Other emergency telephone numbers ChemTrec 1-800-424-9300 (Outside the US 1-703-527-3887) Emergency First Aid: 1-877-740-5015 SECTION 2 Hazard(s) identification Classification of the substance or mixture Classification Eye Irritation Category 2A, Skin Corrosion/Irritation Category 2, Carcinogenicity Category 1A, Specific target organ toxicity repeated exposure Category 1, Flammable Solid Category 1 Label elements Hazard pictogram(s) Signal word Danger Hazard statement(s) For use with Instructor facilitated G3 Blackboard Online course only © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 23 Page 1 continued... Version No: 1.5 Page 2 of 16 Issue Date: 12/16/2020 Masters Pro-Dope H319 Causes serious eye irritation. H315 Causes skin irritation. H350 May cause cancer. H372 Causes damage to organs through prolonged or repeated exposure. H228 Flammable solid. Print Date: 12/16/2020 Physical and Health hazard(s) not otherwise classified Not Applicable Precautionary statement(s) Prevention P201 Obtain special instructions before use. P202 Do not handle until all safety precautions have been read and understood. P210 Keep away from heat/sparks/open flames/hot surfaces. - No smoking. P260 Do not breathe dust/fume. P264 Wash thoroughly after handling. P240 Ground/bond container and receiving equipment. P241 Use explosion-proof electrical/ventilating/lighting/intrinsically safe equipment. P270 Do not eat, drink or smoke when using this product. P280 Wear protective gloves/protective clothing/eye protection/face protection. Precautionary statement(s) Response P308+P313 P321 IF exposed or concerned: Get medical advice/attention. Specific treatment (see advice on this label). P362+P364 Take off contaminated clothing and wash before reuse. P370+P378 In case of fire: Use water jets for extinction. P305+P351+P338 P314 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical advice/attention if you feel unwell. P337+P313 If eye irritation persists: Get medical advice/attention. P302+P352 IF ON SKIN: Wash with plenty of water. P332+P313 If skin irritation occurs: Get medical advice/attention. Precautionary statement(s) Storage P405 Store locked up. Precautionary statement(s) Disposal P501 Dispose of contents/container to authorised hazardous or special waste collection point in accordance with any local regulation. SECTION 3 Composition / information on ingredients Substances See section below for composition of Mixtures Mixtures CAS No %[weight] Name 14807-96-6* 34 Talc 1332-58-7* 20 Kaolin 13463-67-7* 4.6 Titanium dioxide 13983-17-0* 4.4 Calcium silicate 9002-84-0 1 polytetrafluoroethylene 9004-34-6* 0.7 cellulose 14808-60-7* <2 silica crystalline - quartz 5131-66-8 10 propylene glycol monobutyl ether - alpha isomer 67-63-0 7 For use with Instructor facilitated G3 Blackboard Online course only isopropanol © 2021. Gas Technician III Learning Package by Clarke Petty Version 6.0 24 Continued...