NeutrinoE224
Indoor eNodeB/室内基站
Quick Guide/快速指导
P/N: 1701000220
Document version: 01
All rights reserved © Baicells Technologies Co., Ltd.
1
1. Appearance
NeutrionE224 Interface Description
OPT
(Optional) Optical fiber interface, used for external transmission
network
LAN
Gigabit Ethernet interface, used for the initial configuration or
debugging
GPS
(Optional) external GPS antenna, SMA female.
SIM
SIM card slot
PWR
12VDC power supply interface
ANT2
(Reserved) external antenna 2
WAN/POE+
Gigabit Ethernet and POE+ interface, used for external transmission
network and power supply.
EXT-INT
Switch of build-in antenna and external antenna
RST
Power reset button
ANT1
(Reserved) external antenna 1
NOTE: Some models support OPT interface and WAN/POE+ interface simultaneously. Some models only
supports WAN/POE+ interface, refer to the actual device.
NeutrionE224 Interface Indicators
PWR
LTE
ALM
Steady on
The device has powered on.
Fast flash
LTE traffic is transmitting.
Slow flash
The cell has been activated.
Steady on
Alarm that strong interference cell exists arounds
the cell.
Fast flash
S1 alarm.
Slow flash
Other alarms.
All rights reserved © Baicells Technologies Co., Ltd.
1
2. Install eNodeB
To get the signal coverage effect best, the NeutrionE224 should be placed in an
unobstructed space. The NeutrionE224 can be installed on ceiling, wall or placed on the
desktop. If it is placed on the desktop, only the cable connection is required.
Installation Tool
Marker pen
Percussion drill
Cross screw driver
hammer
NOTE: Other accessories have been packed in the packing box.
Install on Ceiling
Attention:

The thickness of ceiling is not less than 18mm, and bearing more than 5kg. If the
strength is not suitable, the device maybe fall off.

If the ceiling is made of unstable material, such as gypsum, this ceiling installation is
not recommended. If the device must be installed on ceiling due to environment
restriction, add one layer better panel under screws to make sure the device is
fastness.
All rights reserved © Baicells Technologies Co., Ltd.
2
Install on Wall
The NeutrionE224 also can be installed on wall, the installation steps is the same as the
ceiling installation.
NOTE: The arrow on the back of the eNodeB must be upward.
Connect Cable
NOTE:
1.
If the eNodeB supports optical interface (OPT) and electrical interface (WAN/POE+) simultaneously,
anyone can be chosen for data back haul. If the eNodeB only supports electrical interface, it is used
for data backhaul.
2.
If POE+ is used for power supply, connect the WAN/POE+ interface to the POE interface of the POE
adapter first, and then connect the LAN port of the POE adapter to the switch.
3.
If POE+ is used for power supply, the POE adapter and the AC power must be placed in a reliable
waterproof box.
Power ON
Power on the eNodeB, and wait a few minutes while the eNodeB boots up. Per the previous
“1 Appearance”, check that the LED indicators are lighting as expected.
All rights reserved © Baicells Technologies Co., Ltd.
3
1. 产品外观
NeutrinoE224 接口说明
OPT
（可选）光纤接口，连接外部传输网络用于数据回传
LAN
千兆以太网LAN口，可用于初始配置或设备调试
GPS
（选配）外接GPS天线，SMA母头
SIM
SIM卡插槽
PWR
12VDC电源接口
ANT2
（预留）外接天线2
WAN/POE+
千兆以太网WAN口，连接外部传输网络用于数据回传和POE+
供电
EXT-INT
内置天线和外接天线开关
RST
电源复位键
ANT1
（预留）外接天线1
说明：某些基站型号同时支持 OPT 口和 WAN/POE+口，某些基站型号仅支持 WAN/POE+口。请以实际设
备为准。
NeutrinoE224 指示灯说明
PWR
LTE
ALM
常亮
设备已上电
快闪
LTE业务传输中
慢闪
小区已激活
常亮
周边存在强干扰小区告警
快闪
S1告警
慢闪
其他告警
All rights reserved © Baicells Technologies Co., Ltd.
4
2. 安装基站
为了使信号覆盖效果达到最佳，请将基站安放在无遮挡区域。NeutrinoE224 可以安装在天
花板、墙壁或者直接放置于桌面，其中桌面放置不需要任何安装步骤，放置到合适地点后，
直接连接线缆即可。
安装工具
记号笔
冲击钻
十字螺丝刀
锤子
说明：其他配件随设备发货。
安装于天花板
注意：

要求天花板厚度小于 18mm，且至少可以承重 5kg 以上。如果不能确保适当的
强度，可能造成产品坠落。

若天花板是由强度较弱的材料制成，如石膏，不建议使用此安装方式。如果由于
环 境 限 制必 须 采用 此 安装 方 式 ，请 在 螺母 下 增加 一 层 强度 较 好的 板 材， 以 确 保
设备安装牢固。
All rights reserved © Baicells Technologies Co., Ltd.
5
安装于墙壁
NeutrinoE224 也可以安装到墙壁上，安装步骤与安装于天花板大致相同。
说明：基站背面的箭头必须朝上。
连接线缆
说明：
1.
当基站同时支持光口（OPT）和电口（WAN/POE+）时，可以选择使用其中一个用于数据
回传；当基站只支持电口时，使用 WAN/POE+口用于数据回传。
2.
当使用 POE+供电时，需将 WAN/POE+口用网线先连接至 POE 适配器的 POE 口，再将
POE 适配器的 LAN 口连接至交换设备。
3.
当使用 POE+供电时，POE 适配器和交流电源必须放置于密闭的防水箱中。
上电
NeutrinoE224 基站上电后，等待约几分钟基站启动完成，此时指示灯会提示基站当前的状
态，参考“1 产品外观”查看基站是否正常工作。
All rights reserved © Baicells Technologies Co., Ltd.
6
Additional Information
CE Compliance
CAUTION:



The plug considered as disconnect device of adapter.
Adapter shall be installed near the equipment and shall be easily accessible.
The device complies with RF specifications when the device used at 20cm from your
body.
Baicells Technologies Co., Ltd. hereby declares that this According to Article 10(2) of
Directive 2014/53/EU, the NeutrionE224 can be used in Europe without restriction. This
information has to be presented in such a way that the user can readily understand it.
Typically, this will necessitate translation into every local language (required by national
consumer laws) of the markets where the equipment is intended to be sold. Illustrations,
pictograms and using international abbreviations for country names may help reduce the
need for translation.
Parameters of pBS42104
Tx Frequency
LTE Band 8: 925MHz~960MHz
Rx Frequency
LTE Band 8: 880MHz~915MHz
Hardware version
Ver.A
Software version
BaiBS_QAFA_1.9.4
Modulation technology
LTE: QPSK, 16QAM, 64QAM
Antenna Type
Internal Antenna OR External Antenna
Max Antenna Gain
LTE Band 8: 2dBi
Max Output Power
LTE Band 8: 24dBm
Parameters of pBS41000
Tx Frequency
LTE TDD Band 40: 2300MHz~2320MHz
Rx Frequency
LTE TDD Band 40: 2300MHz~2320MHz
Hardware version
Ver.A
Software version
BaiBS_QAFA_1.9.4
Modulation technology
LTE: QPSK, 16QAM, 64QAM
Antenna Type
Internal Antenna OR External Antenna
Max Antenna Gain
LTE Band 40: 5dBi
Max Output Power
LTE Band 40: 24dBm
All rights reserved © Baicells Technologies Co., Ltd.
7