pdfcoffee.com pip-pnfs0001-pipe-supports-details-pdf-free

June 2005 Process Industry Practices Piping PIP PNFS0001 Pipe Supports Details PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities, this Practice has been prepared from the technical requirements in the existing standards of major industrial users, contractors, or standards organizations. By harmonizing these technical requirements into a single set of Practices, administrative, application, and engineering costs to both the purchaser and the manufacturer should be reduced. While this Practice is expected to incorporate the majority of requirements of most users, individual applications may involve requirements that will be appended to and take precedence over this Practice. Determinations concerning fitness for purpose and particular matters or application of the Practice to particular project or engineering situations should not be made solely on information contained in these materials. The use of trade names from time to time should not be viewed as an expression of preference but rather recognized as normal usage in the trade. Other brands having the same specifications are equally correct and may be substituted for those named. All Practices or guidelines are intended to be consistent with applicable laws and regulations including OSHA requirements. To the extent these Practices or guidelines should conflict with OSHA or other applicable laws or regulations, such laws or regulations must be followed. Consult an appropriate professional before applying or acting on any material contained in or suggested by the Practice. This Practice is subject to revision at any time by the responsible Function Team and will be reviewed every 5 years. This Practice will be revised, reaffirmed, or withdrawn. Information on whether this Practice has been revised may be found at www.pip.org. © Process Industry Practices (PIP), Construction Industry Institute, The University of Texas at Austin, 3925 West Braker Lane (R4500), Austin, Texas 78759. PIP member companies and subscribers may copy this Practice for their internal use. Changes, overlays, addenda, or modifications of any kind are not permitted within any PIP Practice without the express written authorization of PIP. PIP will not consider requests for interpretations (inquiries) for this Practice. PRINTING HISTORY June 2005 Issued Not printed with State funds June 2005 Process Industry Practices Piping PIP PNFS0001 Pipe Supports Details Table of Contents 1. Introduction................................. 5 1.1 Purpose ............................................. 5 1.2 Scope................................................. 5 2. References .................................. 5 2.1 Industry Codes and Standards.......... 5 2.2 Other References .............................. 5 LARGE BORE PIPE SUPPORTS DETAILS PNFS0100 – DIRECTIONAL STOP DS-1 (FOR INSULATED PIPE NPS 3 TO NPS 24) PNFS0101 – DIRECTIONAL STOP DS-2 (FOR UNINSULATED PIPE NPS 3 TO NPS 24) PNFS0200 – PIPE GUIDE PG-1 (FOR INSULATED PIPE NPS 3 TO NPS 8) PNFS0201 – PIPE GUIDE PG-2 (FOR INSULATED PIPE NPS 3 TO NPS 8) PNFS0205 – PIPE GUIDE PG-3 (FOR INSULATED PIPE NPS 10 TO NPS 24) PNFS0206 – PIPE GUIDE PG-3-H (FOR INSULATED PIPE NPS 10 TO NPS 24) PNFS0209 – PIPE GUIDE PG-4 (FOR UNINSULATED PIPE NPS 3 TO NPS 12) PNFS0210 – PIPE GUIDE PG-5 (FOR BARE PIPE NPS 14 AND NPS 24) PNFS0212 – PIPE GUIDE PG-6 (FOR UNINSULATED VERTICAL PIPING NPS 3 TO NPS 8) PNFS0213 – PIPE GUIDE PG-7 (FOR UNINSULATED VERTICAL PIPING NPS 10 TO NPS 24) PNFS0214 – PIPE GUIDE PG-8 (FOR INSULATED PIPE NPS 3 TO NPS 6) PNFS0215 – PIPE GUIDE PG-9 (FOR INSULATED PIPING PIPE NPS 8 TO NPS 24) PNFS0250 – PIPE GUIDE CLIPS PGC-1 (ATTACHMENTS FOR GUIDES NPS 8 TO NPS 14) PNFS0251 – PIPE GUIDE CLIPS PGC-2 (ATTACHMENTS FOR GUIDES NPS 16 TO NPS 14) PNFS0252 – VESSEL CLIPS PSVC-1 PNFS0253 – VESSEL CLIPS PSVC-2 PNFS0350 – CANTILEVER SUPPORT OFF VESSEL PS-1 PNFS0351 – KNEE BRACE SUPPORT OFF VESSEL PS-2 Process Industry Practices Page 1 of 5 June 2005 PIP PNFS0001 Process Industry Practices LARGE BORE PIPE SUPPORTS DETAILS (continued) PNFS0352 – KNEE BRACE SUPPORT OFF VESSEL PS-3 PNFS0353 – SINGLE KNEE BRACE SUPPORT OFF VESSEL PS-4 PNFS0354 – KNEE BRACE SUPPORT OFF VESSEL PS-5 PNFS0355 – CANTILEVER SUPPORT OFF VESSEL PS-6 (ROUND TYPE CLIPS) PNFS0356 – KNEE BRACE SUPPORT OFF VESSEL PS-7 PNFS0357 – SINGLE KNEE BRACE SUPPORT OFF VESSEL PS-8 (ROUND TYPE CLIPS) PNFS0365 – CANTILEVER BRACKETS PS-16 (FROM ADJACENT STEEL OR VESSEL) PNFS0366 – KNEE BRACED BRACKETS PS-17 (FROM ADJACENT STEEL) PNFS0367 – KNEE BRACED BRACKETS PS-18 (FROM ADJACENT STEEL) PNFS0368 – T-SUPPORT PS-19 (FROM ADJACENT STEEL) PNFS0369 – SINGLE COLUMN BRACKET PS-20 (FROM EXISTING STEEL) PNFS0370 – DOUBLE COLUMN BRACKET PS-21 (FROM EXISTING STEEL) PNFS0371 – SLIDE PLATE ASSSEMBLY PS-22 PNFS0372 – ROD HANGERS PS-23 PNFS0373 – ADJUSTABLE BASE SUPPORT PS-24 (FOR PIPE NPS 3 TO NPS 16) PNFS0374 – STANDARD U-BOLT PS-25 (FOR PIPE NPS 3 TO NPS 24) PNFS0375 – T-SUPPORT PS-26 (FROM GRADE) PNFS0376 – CONTAMINATION PLATE PS-27 PNFS0377 – HANGING T-SUPPORT PS-28 (FOR PIPE NPS 6 AND SMALLER) PNFS0378 – HANGING TRAPEZE FROM CHANNEL PS-29 (FOR PIPE NPS 12 AND SMALLER) PNFS0379 – CANTILEVER BRACKET FROM EXISTING STEEL PS-30 PNFS0380 – SINGLE CANTILEVER FROM EXISTING STEEL PS-31 PNFS0400 – PIPE SHOE S-2 (FOR PIPE NPS 3 NPS 8) PNFS0401 – PIPE SHOE S-3 (FOR PIPE NPS 3 TO NPS 8) PNFS0402 – PIPE SHOE S-4 (FOR PIPE NPS 10 TO NPS 12) PNFS0403 – PIPE SHOE S-5 (FOR PIPE NPS 14 TO NPS 24 WITH LESS THAN 4” INSULATION) PNFS0404 – PIPE SHOE S-6 (FOR PIPE NPS 14 TO NPS 24 WITH 4” TO LESS THAN 6” INSULATION) PNFS0405 – PIPE SHOE S-7 (CLAMP TYPE) (FOR PIPE NPS 3 TO NPS 8) PNFS0406 – PIPE SHOE S-8 (CLAMP TYPE) (FOR PIPE NPS 10 AND NPS 12) PNFS0407 – PIPE SHOE S-9 (CLAMP TYPE) (FOR PIPE NPS 14 AND NPS 24) PNFS0450 – SPRING HANGER ASSEMBLY TYPE C SH-1 (FOR BARE PIPE) PNFS0451 – SPRING HANGER ASSEMBLY TYPE C SH-2 (FOR INSULATED PIPE) PNFS0452 – SPRING HANGER ASSEMBLY TYPE C SH-3 (FOR ALLOY CLAMP) PNFS0453 – SPRING HANGER ASSEMBLY TYPE C SH-4 (WITH WELDING LUG TYPE) PNFS0454 – SPRING HANGER ASSEMBLY TYPE F SH-5 (BASE TYPE AT GRADE) PNFS0455 – SPRING HANGER ASSEMBLY TYPE F SH-6 (BASE TYPE AT GRADE WITH SLIDE PLATE) PNFS0456 – SPRING HANGER ASSEMBLY TYPE F SH-7 (BASE TYPE FROM STEEL) PNFS0457 – SPRING HANGER ASSEMBLY TYPE F SH-8 (BASE TYPE FROM STEEL WITH SLIDE PLATE) PNFS0458 – CONSTANT SPRING HANGER ASSEMBLY TYPE C SH-9 (FOR BARE LINE) PNFS0459 – CONSTANT SPRING HANGER ASSEMBLY TYPE C SH-10 (CONSTANT FOR INSULATED LINE) PNFS0460 – CONSTANT SPRING HANGER ASSEMBLY TYPE C SH-11 (CONSTANT FOR ALLOY CLAMP) PNFS0461 – CONSTANT SPRING HANGER ASSEMBLY TYPE C SH-12 (WITH WELDING TYPE LUGS) PNFS0462 – CONSTANT SPRING HANGER ASSEMBLY TYPE F SH-13 (BASE TYPE FROM STEEL) PNFS0463 – CONSTANT SPRING SUPPORT TYPE F SH-14 (BASE TYPE FROM STEEL WITH SLIDE PLATE) PNFS0464 – SPRING HANGER ASSEMBLY TYPE A SH-15 (WITH WELDING LUGS FROM STEEL) PNFS0465 – SPRING SUPPORT ASSEMBLY TYPE D SH-16 (WITH WELDING LUGS FROM STEEL) PNFS0500 – TRUNNION SUPPORT DETAILS (14 Pages) PNFS0550 – WELDING LUG ATF-11 (FOR PIPING NPS 3 AND LARGER) PNFS0551 – WELDING CLIP ATF-12 (FOR PIPING NPS 3 AND LARGER) PNFS0552 – WELDING CLIP ATF-13 (FOR PIPING NPS 3 AND LARGER) PNFS0560 – WELDING LUG WL-1 PNFS0561 – WELDING LUG WL-2 (ON ELBOW) Page 2 of 5 Process Industry Practices PIP PNFS0001 Process Industry Practices June 2005 SMALL BORE PIPE SUPPORTS DETAILS PNFS0600 – CANTILEVER BRACKET FROM ADJACENT STEEL OR VESSEL FPS-1 (FOR PIPING UP TO NPS 2-1/2) (2 Pages) PNFS0601 – BRACED CANTILEVER BRACKET FROM ADJACENT STEEL OR VESSEL FPS-2 (FOR PIPING UP TO NPS 2-1/2) (2 Pages) PNFS0602 – DOUBLE COLUMN BRACKET FROM ADJACENT STEEL FPS-3 (FOR PIPING UP TO NPS 2-1/2) PNFS0603 – DOUBLE COLUMN HANGER FROM ADJACENT STEEL FPS-4 (FOR PIPING UP TO NPS 2-1/2) PNFS0604 – SINGLE COLUMN BRACKET FROM ADJACENT STEEL FPS-5 (FOR PIPING UP TO NPS 2-1/2) PNFS0605 – SINGLE COLUMN HANGER FROM ADJACENT STEEL FPS-6 (FOR PIPING UP TO NPS 2-1/2) PNFS0606 – T-SUPPORT FROM ADJACENT STEEL FPS-7A (FOR PIPING UP TO NPS 2-1/2) PNFS0607 – T-SUPPORT FROM ADJACENT STEEL FPS-7B (FOR PIPING UP TO NPS 2-1/2) PNFS0608 – CANTILEVER BRACKET FOR HORIZONTAL PIPING FROM ADJACENT STEEL FPS-9 (FOR PIPING UP TO NPS 2-1/2) PNFS0609 – SINGLE “L” SUPPORT OR HANGER ADJACENT TO STEEL OR VESSEL FPS-10 (FOR PIPING UP TO NPS 2-1/2) PNFS0611 – SUPPORT FOR VERTICAL PIPING FPS-12 (FOR PIPING UP TO NPS 2-1/2) PNFS0612 – CANTILEVER SUPPORT ADJACENT TO STEEL FPS-13 (FOR PIPING UP TO NPS 2-1/2) PNFS0614 – CANTILEVER BRACKET FOR PIPE SUPPORTS FPS-16 (FOR PIPING UP TO NPS 2-1/2) PNFS0614 – CANTILEVER BRACKET FOR PIPE SUPPORTS FPS-15 (FOR PIPING UP TO NPS 2-1/2) PNFS0615 – CANTILEVER BRACKET FOR PIPE SUPPORTS FPS-16 (FOR PIPING UP TO NPS 2-1/2) PNFS0615 – CANTILEVER BRACKET FOR PIPE SUPPORTS FPS-16 (FOR PIPING UP TO NPS 2-1/2) PNFS0619 – SUPPLEMENTARY STEEL DETAIL FPS-20 (FOR PIPING UP TO NPS 2-1/2) PNFS0620 – SUPPLEMENTARY STEEL DETAIL FPS-21 (FOR PIPING UP TO NPS 2-1/2) PNFS0625 – CINCH PLATE FPS-26 (FOR PIPING UP TO NPS 2-1/2) PNFS0627 – ‘T’ POST FPS-28 (FOR PIPING UP TO NPS 2-1/2) PNFS0628 – ‘T’ POST FPS-29 (FOR PIPING UP TO NPS 2-1/2) PNFS0629 – SUPPORT FROM GRADE OR STEEL FPS-30 (FOR PIPING UP TO NPS 2-1/2) (2 Pages) PNFS0639 – ADJUSTABLE SUPPORT FROM GRADE OR STEEL FPS-40 (FOR PIPING UP TO NPS 2-1/2) PNFS0640 – ADJUSTABLE SUPPORT FROM GRADE OR STEEL FPS-41 (FOR PIPING UP TO NPS 2-1/2) PNFS0641 – SUPPORT FOR DRAIN FPS-42 (FOR PIPING UP TO NPS 2-1/2) PNFS0649 – CANTILEVER BRACKET FROM ADJACENT PIPING FPS-50 (FOR PIPING UP TO NPS 2-1/2) PNFS0650 – CANTILEVER BRACKET FROM ADJACENT PIPING FPS-51 (FOR PIPING UP TO NPS 2-1/2) PNFS0651 – CANTILEVER BRACKET FROM ADJACENT PIPING FPS-52 (FOR PIPING UP TO NPS 2-1/2) PNFS0663 – BRACED CANTILEVER BRACKET FROM ADJACENT VESSEL FPS-64 (FOR PIPING UP TO NPS 2-1/2) PNFS0664 – BRACKET FOR VERTICAL PIPING FROM ADJACENT VESSEL FPS-65 (FOR PIPING UP TO NPS 2-1/2) (2 Pages) PNFS0679 – BRACED CANTILEVER BRACKET FOR HORIZONTAL PIPING FROM ADJACENT VESSEL FPS-80 (FOR PIPING UP TO NPS 2-1/2) PNFS0700 – SHORT LENGTH ROD HANGER FROM ADJACENT STEEL FPH-1 (FOR PIPING UP TO NPS 2-1/2) (2 Pages) PNFS0701 – LONG LENGTH ROD HANGER FPH-2 (FOR PIPING UP TO NPS 2-1/2) (2 Pages) PNFS0702 – TRAPEZE TYPE ROD HANGER FPH-3 (FOR PIPING UP TO NPS 2-1/2) PNFS0771 – ANCHOR FROM GRADE OR STEEL FPA-22 (FOR PIPING UP TO NPS 2-1/2) PNFS0800 – GUIDE FOR INSULATED HORIZONTAL PIPING FROM ADJACENT STEEL FPG-1 (FOR PIPING UP TO NPS 2-1/2) PNFS0802 – GUIDE FROM STEEL FPG-3 (FOR PIPING UP TO NPS 2-1/2) PNFS0805 – STOP FOR HORIZONTAL PIPING FROM ADJACENT STEEL FPG-6 (FOR PIPING UP TO NPS 2-1/2) PNFS0807 – STOP FOR HORIZONTAL PIPING FROM ADJACENT STEEL FPG-8 (FOR PIPING UP TO NPS 2-1/2) PNFS0809 – GUIDE FOR UNINSULATED VERTICAL PIPING FROM ADJACENT TOWER OR STEEL FPG-10 (FOR PIPING UP TO NPS 2-1/2) PNFS0810 – GUIDE FOR UNINSULATED VERTICAL PIPING FROM ADJACENT STEEL FPG-11 (FOR PIPING UP TO NPS 2-1/2) (2 Pages) PNFS0816 – GUIDE FOR VERTICAL PIPING FROM VESSELFPG-17 (FOR PIPING UP TO NPS 2-1/2) (3 Pages) PNFS0820 – GUIDE ADJACENT TO GRADE OR STEEL FPG-21A & 21B (FOR PIPING UP TO NPS 2-1/2) PNFS0821 – 4-WAY STOP ADJACENT TO GRADE OR STEEL FPG-21C (FOR PIPING UP TO NPS 2-1/2) Process Industry Practices Page 3 of 5 June 2005 PIP PNFS0001 Process Industry Practices SMALL BORE PIPE SUPPORTS DETAILS (continued) PNFS0828 – HOLD DOWN SUPPORT AND HORIZONTAL GUIDE FPG-29 (FOR PIPING UP TO NPS 2-1/2) (3 Pages) PNFS0850 – WELDING LUG ATF-1 (FOR PIPING UP TO NPS 2-1/2) PNFS0851 – WELDING CLIP DETAIL ATF-2 (FOR PIPING UP TO NPS 2-1/2) PNFS0852 – WELDING CLIP DETAIL ATF-3 (FOR PIPING UP TO NPS 2-1/2) PNFS0853 – HANGER ATTACHMENT ATF-4 (FOR PIPING UP TO NPS 2-1/2) PNFS0856 – HANGER ATTACHMENT ATF-7 (FOR PIPING UP TO NPS 2-1/2) (3 Pages) PNFS0857 – SPECIAL STEEL WASHER PLATE ATF-8 (FOR PIPING UP TO NPS 2-1/2) PNFS0859 – HANGER ATTACHMENT ATF-10 (FOR PIPING UP TO NPS 2-1/2) PNFS0861 – HANGER ATTACHMENT ATF-11 (FOR PIPING UP TO NPS 2-1/2) PNFS0863 – BRACE FOR RELIEF VALVE ATF-14 (FOR PIPING UP TO NPS 2-1/2) PNFS0866 – BRACKET DETAIL ATF-17 (FOR PIPING UP TO NPS 2-1/2) PNFS0900 – FORGED STEEL CLEVIS CLF (FOR PIPING UP TO NPS 2-1/2) PNFS0901 – STANDARD U-BOLT UBF (FOR PIPING UP TO NPS 2-1/2) PNFS0902 – STRAIGHT OR EYE ROD RF/HF (FOR PIPING UP TO NPS 2-1/2) PNFS0910 – PIPE SUPPORT DETAILS FF-1A THROUGH FS-1D (FOR PIPING UP TO NPS 2-1/2) PNFS0911 – CLAMPED PIPE SHOE DETAILS FS-1J THROUGH FS-1N (FOR PIPING UP TO NPS 2-1/2) Page 4 of 5 Process Industry Practices PIP PNFS0001 Process Industry Practices 1. May 2005 Introduction 1.1 Purpose This Practice provides fabrication/installation details for pipe supports. 1.2 Scope This Practice describes the minimum requirements to fabricate or install supports for large and small bore piping. The details provide dimensional and engineering requirements for the design and engineering of pipe supports. 2. References Applicable parts of the following industry codes and standards, and references shall be considered an integral part of this Practice. The edition in effect on the date of contract award shall be used, except as otherwise noted. Short titles are used herein where appropriate. 2.1 Industry Codes and Standards • Manufacturers Standard Specifications – 2.2 MSS SP-58 – Pipe Hangers and Supports – Materials, Design and Manufacturing Other References • Grinnel Pipe Hangers Process Industry Practices Page 5 of 5 This page intentionally left blank. PIP PNFS0001 Process Industry Practices June 2005 LARGE BORE PIPE SUPPORTS DRAWING NUMBER DETAIL NUMBER PNFS0100 DS-1 DIRECTIONAL STOP DS-1 (FOR INSULATED PIPE NPS 3 TO NPS 24) PNFS0101 DS-2 DIRECTIONAL STOP DS-2 (FOR UNINSULATED PIPE NPS 3 TO NPS 24) PNFS0200 PG-1 PIPE GUIDE PG-1 (FOR INSULATED PIPE NPS 3 TO NPS 8) PNFS0201 PG-2 PIPE GUIDE PG-2 (FOR INSULATED PIPE NPS 3 TO NPS 8) PNFS0205 PG-3 PIPE GUIDE PG-3 (FOR INSULATED PIPE NPS 10 TO NPS 24) PNFS0206 PG-3-H PIPE GUIDE PG-3-H (FOR INSULATED PIPE NPS 10 TO NPS 24) PNFS0209 PG-4 PIPE GUIDE PG-4 (FOR UNINSULATED PIPE NPS 3 TO NPS 12) DESCRIPTION PNFS0210 PG-5 PIPE GUIDE PG-5 (FOR BARE PIPE NPS 14 AND NPS 24) PNFS0212 PG-6 PIPE GUIDE PG-6 (FOR UNINSULATED VERTICAL PIPING NPS 3 TO NPS 8) PNFS0213 PG-7 PIPE GUIDE PG-7 (FOR UNINSULATED VERTICAL PIPING NPS 10 TO NPS 24) PNFS0214 PG-8 PIPE GUIDE PG-8 (FOR INSULATED PIPE NPS 3 TO NPS 6) PNFS0215 PG-9 PIPE GUIDE PG-9 (FOR INSULATED PIPING PIPE NPS 8 TO NPS 24) PNFS0250 PGC-1 PIPE GUIDE CLIPS PGC-1 (ATTACHMENTS FOR GUIDES NPS 8 TO NPS 14) PNFS0251 PGC-2 PIPE GUIDE CLIPS PGC-2 (ATTACHMENTS FOR GUIDES NPS 16 TO NPS 14) PNFS0252 PSVC-1 VESSEL CLIPS PSVC-1 PNFS0253 PSVC-2 PNFS0350 PS-1 VESSEL CLIPS PSVC-2 CANTILEVER SUPPORT OFF VESSEL PS-1 PNFS0351 PS-2 KNEE BRACE SUPPORT OFF VESSEL PS-2 PNFS0352 PS-3 KNEE BRACE SUPPORT OFF VESSEL OS03 PNFS0353 PS-4 SINGLE KNEE BRACE SUPPORT OFF VESSEL PS-4 PNFS0354 PS-5 KNEE BRACE SUPPORT OFF VESSEL PS-5 PNFS0355 PS-6 CANTILEVER SUPPORT OFF VESSEL PS-6 (ROUND TYPE CLIPS) PNFS0356 PS-7 KNEE BRACE SUPPORT OFF VESSEL PS-7 PNFS0357 PS-8 SINGLE KNEE BRACE SUPPORT OFF VESSEL PS-8 (ROUND TYPE CLIPS) PNFS0365 PS-16 CANTILEVER BRACKETS PS-16 (FROM ADJACENT STEEL OR VESSEL) PNFS0366 PS-17 KNEE BRACED BRACKETS PS-17 (FROM ADJACENT STEEL) PNFS0367 PS-18 KNEE BRACED BRACKETS PS-18 (FROM ADJACENT STEEL) PNFS0368 PS-19 T-SUPPORT PS-19 (FROM ADJACENT STEEL) PNFS0369 PS-20 SINGLE COLUMN BRACKET PS-20 (FROM EXISTING STEEL) PNFS0370 PS-21 DOUBLE COLUMN BRACKET PS-21 (FROM EXISTING STEEL) PNFS0371 PS-22 SLIDE PLATE ASSSEMBLY PS-22 PNFS0372 PS-23 ROD HANGERS PS-23 PNFS0373 PS-24 ADJUSTABLE BASE SUPPORT PS-24 (FOR PIPE NPS 3 TO NPS 16) PNFS0374 PS-25 STANDARD U-BOLT PS-25 (FOR PIPE NPS 3 TO NPS 24) PNFS0375 PS-26 T-SUPPORT (FROM GRADE) PS-26 PNFS0376 PS-27 CONTAMINATION PLATE PS-27 PNFS0377 PS-28 HANGING T-SUPPORT PS-28 (FOR PIPE NPS 6 AND SMALLER) PNFS0378 PS-29 HANGING TRAPEZE FROM CHANNEL PS-29 (FOR PIPE NPS 12 AND SMALLER) PNFS0379 PS-30 CANTILEVER BRACKET FROM EXISTING STEEL PS-30 PNFS0380 PS-31 SINGLE CANTILEVER FROM EXISTING STEEL PS-31 PNFS0400 S-2 PIPE SHOE S-2 (FOR PIPE NPS 3 NPS 8) PNFS0401 S-3 PIPE SHOE S-2 (FOR PIPE NPS 3 TO NPS 8) PIP PNFS0001 June 2005 Process Industry Practices LARGE BORE PIPE SUPPORTS (Continued) DRAWING NUMBER DETAIL NUMBER PNFS0402 S-4 PIPE SHOE S-4 (FOR PIPE NPS 10 TO NPS 12) PNFS0403 S-5 PIPE SHOE S-5 (FOR PIPE NPS 14 TO NPS 24 WITH LESS THAN 4” INSULATION) PNFS0404 S-6 PIPE SHOE S-6 (FOR PIPE NPS 14 TO NPS 24 WITH 4” TO LESS THAN 6” INSULATION) PNFS0405 S-7 PIPE SHOE S-7 (CLAMP TYPE) (FOR PIPE NPS 3 TO NPS 8) PNFS0406 S-8 PIPE SHOE S-8 (CLAMP TYPE) (FOR PIPE NPS 10 AND NPS 12) PNFS0407 S-9 PIPE SHOE S-9 (CLAMP TYPE) (FOR PIPE NPS 14 AND NPS 24) PNFS0450 SH-1 SPRING HANGER ASSEMBLY TYPE C SH-1 (FOR BARE PIPE) PNFS0451 SH-2 SPRING HANGER ASSEMBLY TYPE C SH-2 (FOR INSULATED PIPE) DESCRIPTION PNFS0452 SH-3 SPRING HANGER ASSEMBLY TYPE C SH-3 (FOR ALLOY CLAMP) PNFS0453 SH-4 SPRING HANGER ASSEMBLY TYPE C SH-4 (WITH WELDING LUG TYPE) PNFS0454 SH-5 SPRING HANGER ASSEMBLY TYPE F SH-5 (BASE TYPE AT GRADE) PNFS0455 SH-6 SPRING HANGER ASSEMBLY TYPE F SH-6 (BASE TYPE AT GRADE WITH SLIDE PLATE) PNFS0456 SH-7 SPRING HANGER ASSEMBLY TYPE F SH-7 (BASE TYPE FROM STEEL) PNFS0457 SH-8 SPRING HANGER ASSEMBLY TYPE F SH-8 (BASE TYPE FROM STEEL WITH SLIDE PLATE) PNFS0458 SH-9 CONSTANT SPRING HANGER ASSEMBLY TYPE C SH-9 (FOR BARE LINE) PNFS0459 SH-10 CONSTANT SPRING HANGER ASSEMBLY TYPE C SH-10 (CONSTANT FOR INSULATED LINE) PNFS0460 SH-11 CONSTANT SPRING HANGER ASSEMBLY TYPE C SH-11 (CONSTANT FOR ALLOY CLAMP) PNFS0461 SH-12 CONSTANT SPRING HANGER ASSEMBLY TYPE C SH-12 (WITH WELDING TYPE LUGS) PNFS0462 SH-13 CONSTANT SPRING HANGER ASSEMBLY TYPE F SH-13 (BASE TYPE FROM STEEL) PNFS0463 SH-14 CONSTANT SPRING SUPPORT TYPE F SH-14 (BASE TYPE FROM STEEL WITH SLIDE PLATE) PNFS0464 SH-15 SPRING HANGER ASSEMBLY TYPE A SH-15 (WITH WELDING LUGS FROM STEEL) PNFS0465 SH-16 SPRING SUPPORT ASSEMBLY TYPE D SH-16 (WITH WELDING LUGS FROM STEEL) PNFS0500 TR-A TRUNNION SUPPORT TR-A (HORIZONTAL SUPPORT ON HORIZONTAL PIPE), Page 1 PNFS0500 TR-B TRUNNION SUPPORT TR-B (VERTICAL SUPPORT ON HORIZONTAL PIPE), Page 2 PNFS0500 TR-C TRUNNION SUPPORT TR-C (VERTICAL SUPPORT ON VERTICAL ELL), Page 3 PNFS0500 TR-D TRUNNION SUPPORT TR-D (HORIZONTAL SUPPORT ON VERTICAL ELL), Page 4 PNFS0500 TR-E TRUNNION SUPPORT TR-E (HORIZONTAL SUPPORT ON VERTICAL ELL), Page 5 PNFS0500 TR-F TRUNNION SUPPORT TR-F (HORIZONTAL SUPPORT ON VERTICAL ELL), Page 6 PNFS0500 TR-G TRUNNION SUPPORT TR-G (BOLTED SUPPORT ON VERTICAL PIPE), Page 7 PNFS0500 TR-H TRUNNION SUPPORT TR-H (BOLTED SUPPORT ON VERTICAL ELL), Page 8 PNFS0500 TR-J TRUNNION SUPPORT TR-J (ADJUSTABLE), Page 9 PNFS0500 TR-K TRUNNION SUPPORT TR-K (HORIZONTAL SUPPORT ON HORIZONTAL ELL), Page 10 PNFS0500 TR-M TRUNNION SUPPORT TR-M, Page 11 PNFS0500 TR-1 TYPICAL TRUNNION ATTACHMENT DETAIL TR-1, Page 12 PNFS0500 TR-2 TRUNNION ATTACHMENT BASE PLATES TR-2, Page 13 PNFS0500 TR-3 PNFS0550 ATF-11 WELDING LUG ATF-11 (FOR PIPING NPS 3 AND LARGER) TYPICAL TRUNNION DESIGNATIONS ON ISOMETRIC PIPING DRAWINGS TR-3, Page 14 PNFS0551 ATF-12 WELDING CLIP ATF-12 (FOR PIPING NPS 3 AND LARGER) PNFS0552 ATF-13 WELDING CLIP ATF-13 (FOR PIPING NPS 3 AND LARGER) PNFS0560 WL-1 WELDING LUG WL-1 PNFS0561 (PNFS0560 page 2) WL-2 WELDING LUG WL-2 (ON ELBOW) PIP PNFS0001 Process Industry Practices June 2005 SMALL BORE PIPE SUPPORTS DRAWING NUMBER DETAIL NUMBER PNFS0600 FPS-1 CANTILEVER BRACKET FROM ADJACENT STEEL OR VESSEL FPS-1 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0600 FPS-1 CANTILEVER BRACKET FROM ADJACENT STEEL OR VESSEL FPS-1 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0601 FPS-2 BRACED CANTILEVER BRACKET FROM ADJACENT STEEL OR VESSEL FPS-2 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0601 FPS-2 BRACED CANTILEVER BRACKET FROM ADJACENT STEEL OR VESSEL FPS-2 (FOR PIPING UP TO NPS 2-1/2), Page 2 DESCRIPTION PNFS0602 FPS-3 DOUBLE COLUMN BRACKET FROM ADJACENT STEEL FPS-3 (FOR PIPING UP TO NPS 2-1/2) PNFS0603 FPS-4 DOUBLE COLUMN HANGER FROM ADJACENT STEEL FPS-4 (FOR PIPING UP TO NPS 2-1/2) PNFS0604 FPS-5 SINGLE COLUMN BRACKET FROM ADJACENT STEEL FPS-5 (FOR PIPING UP TO NPS 2-1/2) PNFS0605 FPS-6 PNFS0606 FPS-7A T-SUPPORT FROM ADJACENT STEEL FPS-7A (FOR PIPING UP TO NPS 2-1/2) SINGLE COLUMN HANGER FROM ADJACENT STEEL FPS-6 (FOR PIPING UP TO NPS 2-1/2) PNFS0607 (PNFS0606 page 2) FPS-7B T-SUPPORT FROM ADJACENT STEEL FPS-7B (FOR PIPING UP TO NPS 2-1/2) PNFS0608 FPS-9 CANTILEVER BRACKET FOR HORIZONTAL PIPING FROM ADJACENT STEEL FPS-9 (FOR PIPING UP TO NPS 2-1/2) PNFS0609 FPS-10 SINGLE “L” SUPPORT OR HANGER ADJACENT TO STEEL OR VESSEL FPS-10 (FOR PIPING UP TO NPS 2-1/2) PNFS0611 FPS-12 SUPPORT FOR VERTICAL PIPING FPS-12 (FOR PIPING UP TO NPS 2-1/2) PNFS0612 FPS-13 CANTILEVER SUPPORT ADJACENT TO STEEL FPS-13 (FOR PIPING UP TO NPS 2-1/2) PNFS0614 FPS-15 CANTILEVER BRACKET FOR PIPE SUPPORTS FPS-15 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0614 FPS-15 CANTILEVER BRACKET FOR PIPE SUPPORTS FPS-15 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0615 FPS-16 CANTILEVER BRACKET FOR PIPE SUPPORTS FPS-16 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0615 FPS-16 CANTILEVER BRACKET FOR PIPE SUPPORTS FPS-16 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0619 FPS-20 SUPPLEMENTARY STEEL DETAIL FPS-20 (FOR PIPING UP TO NPS 2-1/2) PNFS0620 FPS-21 SUPPLEMENTARY STEEL DETAIL FPS-21 (FOR PIPING UP TO NPS 2-1/2) PNFS0625 FPS-26 CINCH PLATE FPS-26 (FOR PIPING UP TO NPS 2-1/2) PNFS0627 FPS-28 ‘T’ POST FPS-28 (FOR PIPING UP TO NPS 2-1/2) PNFS0628 FPS-29 ‘T’ POST FPS-29 (FOR PIPING UP TO NPS 2-1/2) PNFS0629 FPS-30 SUPPORT FROM GRADE OR STEEL FPS-30 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0629 FPS-30 SUPPORT FROM GRADE OR STEEL FPS-30 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0639 FPS-40 ADJUSTABLE SUPPORT FROM GRADE OR STEEL FPS-40 (FOR PIPING UP TO NPS 2-1/2) PNFS0640 FPS-41 ADJUSTABLE SUPPORT FROM GRADE OR STEEL FPS-41 (FOR PIPING UP TO NPS 2-1/2) PNFS0641 FPS-42 SUPPORT FOR DRAIN FPS-42 (FOR PIPING UP TO NPS 2-1/2) PNFS0649 FPS-50 CANTILEVER BRACKET FROM ADJACENT PIPING FPS-50 (FOR PIPING UP TO NPS 2-1/2) PNFS0650 FPS-51 CANTILEVER BRACKET FROM ADJACENT PIPING FPS-51 (FOR PIPING UP TO NPS 2-1/2) PNFS0651 FPS-52 CANTILEVER BRACKET FROM ADJACENT PIPING FPS-52 (FOR PIPING UP TO NPS 2-1/2) PNFS0663 FPS-64 BRACED CANTILEVER BRACKET FROM ADJACENT VESSEL FPS-64 (FOR PIPING UP TO NPS 2-1/2) PNFS0664 FPS-65 BRACKET FOR VERTICAL PIPING FROM ADJACENT VESSEL FPS-65 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0664 FPS-65 BRACKET FOR VERTICAL PIPING FROM ADJACENT VESSEL FPS-65 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0679 FPS-80 BRACED CANTILEVER BRACKET FOR HORIZONTAL PIPING FROM ADJACENT VESSEL FPS-80 (FOR PIPING UP TO NPS 2-1/2) PNFS0700 FPH-1 SHORT LENGTH ROD HANGER FROM ADJACENT STEEL FPH-1 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0700 FPH-1 SHORT LENGTH ROD HANGER FPH-1 (FOR PIPING UP TO NPS 2-1/2), Page 2 PIP PNFS0001 June 2005 Process Industry Practices SMALL BORE PIPE SUPPORTS (Continued) DRAWING NUMBER DETAIL NUMBER PNFS0701 FPH-2 LONG LENGTH ROD HANGER FPH-2 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0701 FPH-2 LONG LENGTH ROD HANGER FPH-2 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0702 FPH-3 TRAPEZE TYPE ROD HANGER FPH-3 (FOR PIPING UP TO NPS 2-1/2) PNFS0771 FPA-22 ANCHOR FROM GRADE OR STEEL FPA-22 (FOR PIPING UP TO NPS 2-1/2) PNFS0800 FPG-1 GUIDE FOR INSULATED HORIZONTAL PIPING FROM ADJACENT STEEL FPG-1 (FOR PIPING UP TO NPS 2-1/2) DESCRIPTION PNFS0802 FPG-3 GUIDE FROM STEEL FPG-3 (FOR PIPING UP TO NPS 2-1/2) PNFS0805 FPG-6 STOP FOR HORIZONTAL PIPING FROM ADJACENT STEEL FPG-6 (FOR PIPING UP TO NPS 2-1/2) PNFS0807 FPG-8 STOP FOR HORIZONTAL PIPING FROM ADJACENT STEEL FPG-8 (FOR PIPING UP TO NPS 2-1/2) PNFS0809 FPG-10 GUIDE FOR UNINSULATED VERTICAL PIPING FROM ADJACENT TOWER OR STEEL FPG-10 (FOR PIPING UP TO NPS 2-1/2) PNFS0810 FPG-11 GUIDE FOR UNINSULATED VERTICAL PIPING FROM ADJACENT STEEL FPG-11 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0810 FPG-11 GUIDE FOR UNINSULATED VERTICAL PIPING FROM ADJACENT STEEL FPG-11 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0816 FPG-17 GUIDE FOR VERTICAL PIPING FROM VESSEL FPG-17 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0816 FPG-17 GUIDE FOR HORIZONTAL PIPING FROM VESSEL FPG-17 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0816 FPG-17 GUIDE FOR HORIZONTAL PIPING FROM ADJACENT STEEL FPG-17 (FOR PIPING UP TO NPS 2-1/2), Page 3 PNFS0820 (page 1) FPG-21A & FPG-21B PNFS0821 (PNFS0820 page 2) FPG-21C PNFS0828 FPG-29 HOLD DOWN SUPPORT AND HORIZONTAL GUIDE FPG-29 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0828 FPG-29 HOLD DOWN PIPE SUPPORT FPG-29 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0828 FPG-29 PNFS0850 ATF-1 WELDING LUG ATF-1 (FOR PIPING UP TO NPS 2-1/2) PNFS0851 ATF-2 WELDING CLIP DETAIL ATF-2 (FOR PIPING UP TO NPS 2-1/2) GUIDE ADJACENT TO GRADE OR STEEL FPG-21A & FPG-21B (FOR PIPING UP TO NPS 2-1/2) 4-WAY STOP ADJACENT TO GRADE OR STEEL FPG-21C (FOR PIPING UP TO NPS 2-1/2) HOLD DOWN PIPE SUPPORT FPG-29 (FOR PIPING UP TO NPS 2-1/2), Page 3 PNFS0852 ATF-3 WELDING CLIP DETAIL ATF-3 (FOR PIPING UP TO NPS 2-1/2) PNFS0853 ATF-4 HANGER ATTACHMENT ATF-4 (FOR PIPING UP TO NPS 2-1/2) PNFS0856 ATF-7 HANGER ATTACHMENT ATF-7 (FOR PIPING UP TO NPS 2-1/2), Page 1 PNFS0856 ATF-7 HANGER ATTACHMENT ATF-7 (FOR PIPING UP TO NPS 2-1/2), Page 2 PNFS0856 ATF-7 HANGER ATTACHMENT ATF-7 (FOR PIPING UP TO NPS 2-1/2), Page 3 PNFS0857 ATF-8 SPECIAL STEEL WASHER PLATE ATF-8 (FOR PIPING UP TO NPS 2-1/2) PNFS0859 ATF-10 HANGER ATTACHMENT ATF-10 (FOR PIPING UP TO NPS 2-1/2) PNFS0861 ATF-11 HANGER ATTACHMENT ATF-11 (FOR PIPING UP TO NPS 2-1/2) PNFS0863 ATF-14 BRACE FOR RELIEF VALVE ATF-14 (FOR PIPING UP TO NPS 2-1/2) PNFS0866 ATF-17 BRACKET DETAIL ATF-17 (FOR PIPING UP TO NPS 2-1/2) PNFS0900 CLF FORGED STEEL CLEVIS CLF (FOR PIPING UP TO NPS 2-1/2) PNFS0901 UBF STANDARD U-BOLT UBF (FOR PIPING UP TO NPS 2-1/2) PNFS0902 RF/HF PNFS0910 (PNFS0550 page 1) FS-1A through FS-1D SHOE DETAILS FS-1A THROUGH FS-1D (FOR PIPING UP TO NPS 2-1/2) PNFS0911 (PNFS0550 page 2) FS-1J through FS-1N CLAMPED SHOE DETAILS FS-1J THROUGH FS-1N (FOR PIPING UP TO NPS 2-1/2) STRAIGHT OR EYE ROD RF/HF (FOR PIPING UP TO NPS 2-1/2) PNFS010 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 DIRECTIONAL STOP DS-1 {FOR INSULATED PIPE NPS 3 TO 24) SEE PNFS0400 THRU PNFS0404 3 SIDES (TYP.) J __ ---'----~ --~---I I t-- ----r---- T--- 1 1 --------~-- --+=~~~,..~=-~ 3 SIDES (TYP.) 1/16" CUEAR 1/16" CUEAR NO WELD (TYP.) -H---'- (TYP.) THIS SIDE (TYP.) ELEVATION- TYPE 2 & 3 ELEVATION- TYPE 1 TYPE PIPE SIZE (NPS) t.41 HORIZ. FORCE (USER DEFINED) 1 3 TO 8 L3X3X3/BXO' -6"LG. USER DEFINED 2 10 & 12 WT4X9 USER DEFINED 3 14 TO 24 WT6X13 USER DEFINED IPIPE SUPPORT MARK NO.I ~ DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. \__TYPE PNFS0101 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS DIRECTIONAL STOP DS-2 (FOR UNINSULATED PIPE NPS 3 TO 24) OCT 2004 PAGE 1 OF 1 II I I II I ___ T__ _ ___ l __ _ I ------+------- I Ill II I 4" (TYPE 1 6" (TYPE 2 (TYP.) 1/16" CLEAR (TYP.) ELEVATION- TYPE 1 (4" WIDE) ELEVATION-TYPE 2 (6" WIDE) PI~~ ~~ZE NPS TYPE ELEVATION- TYPE 3 & 4 ~~ORIZ. FORC~\ M1 USER DEFINED 1 3 TO 4 1/2 lHICK II!. USER DEFINED 2 6 TO 8 1/2 lHICK II!. USER DEFINED 3 10 4 14 TO 24 & 12 WT4X9 USER DEFINED WT6X13 USER DEFINED I PIPE suPPORT MARK No.I ~ DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. \__TYPE PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 PNFS020 PIPE GUIDE PG-1 (FOR INSULATED PIPE NPS 3 TO 8) ocT 2004 PAGE 1 OF 1 ,---r===~ :F:=,=·=r-===i: 1 11 1 Ill --------------+---4 r-----t.--------------~ II 1!1 II 'I 'I' I' -f= I -t+---~1 : ---Ftc:=-==:J -f •I I II'I I IiI I• IIII ----------------rr-----< ' >-----r,-------------I I !b::_j:~::d! k---' J ----=t---PLAN 3" 1/2" PLATE 3 1/2x1/2 • "' --.1'--.1'-----'1/16" CLEAR (TYP.) ELEVATION I PIPE suPPORT MARK No.I I PG-1 I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 PIPE GUIDE PG-2 (FOR INSULATED PIPE NPS 3 TO 8) PNFS0201 ocT 2004 PAGE 1 OF 1 II II -:::= r~= II II I L3X3X3/B EXISTING BEA: -7- ------------------1 f -.l'--.l'--1 16-.-C-LE;R (TYP-.)--- - - - - ELEVATION I PIPE suPPORT MARK No.I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I PG-21 PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 PNFS020 ocT 2004 PAGE 1 OF 1 PIPE GUIDE PG-3 {FOR INSULATED PIPE NPS 10 TO 24) • "' PLAN ~1 t.tt =~~=:;n IIi h 1 ,z.l" II EXISTING PIPE SHOE I - - - - - - - - -f- - - -I- - - - - - - - - - - - - I I I - - - - - - - - -f- - - - - - - - - - - - - - - - - I I - - - - - - - - -r-- - - - - - - - - - - - - - - - - I _/ 1/8" CLEAR {TYP.) EXISTING BEAM ELEVATION PIPE SUPPORT MARK NO. IPG-31 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 PIPE GUIDE/HOLD DOWN PG-3-H {FOR INSULATED PIPE NPS 10 TO 24) PNFS020 ocT 2004 PAGE 1 OF 1 • "' PLAN f----------+1-------------l EXISTING BEAM ELEVATION I PIPE suPPORT MARK No.I I PG-3-H I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 PIPE GUIDE PG-4 {FOR UNINSULATED PIPE NPS 3 THRU 12) f L3X3X3/B -'~<--+-- r - - n PNFS0209 ocT 2004 1 1 PAGE OF /16" CLEAR (TYP.) 'l II I---EXISTING STIEEL TYPE 1 (FOR NPS 3 AND 4 PIPE) f /16" CLEAR (TYP.) 'lnr~"' .------n It 1 - - - EXISTING STIEEL TYPE 2 (FOR NPS 6 TO 12 PIPE) PIPE SUPPORT MARK NO. DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS PIPE GUIDE PG-5 {FOR BARE PIPE NPS 14 TO 24) PNFS021 OCT 2004 PAGE 1 OF 1 1 - - - EXISTING STEEL SIDE VIEW ELEVATION NPS M1 A MAX. LOAD "H" CUSER DEFINED) 14 WT4X13 10" USER DEFINED 16 WT4X13 11" USER DEFINED 18 W4X13 12" USER DEFINED 20 W4X13 13" USER DEFINED 24 W4X13 15" USER DEFINED I PIPE suPPORT MARK No.I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. ~PIPE SIZE PNFS021 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS PIPE GUIDE PG-6 (FOR UNINSULATED VERT. PIPING NPS 3 TO 8) \• O.D. OF VESSEL \ 3'-0" MAX. A \ L4X4X3/8 4" ' I --~ ::.::.:-.. ______ _ -------------+--+-+------ I I PSVC-1 PSVC-2 PIPE & 'f.------SUPPORT ..,...-~-L-.1.1 0:., , ruP o1- ' L-~------- -~ L.... ···"" EXISTING__/; ____ _j VESSEL OCT 2004 PAGE 1 OF 1 / ~ PLAN , ~, 1/8" MAXIMUM O.D. OF VESSEL I' ELEV. Y ELEVATION TYPE M1 H (MAX) (USER DEFINED) 1 L4X4X3/8 USER DEFINED 2 C6X8.2 USER DEFINED 3 CBX11.5 USER DEFINED PIPE SUPPORT MARK NO. ~ DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. \._"'i~E SIZE PNFS021 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 PIPE GUIDE PG-7 (FOR UNINSULATED VERT. PIPING NPS 10 TO 24) 3'-6" MAX. O.D. OF VESSEL A ~r4_l ••_ \, ---\... ----- 1 • \r-----I --+---------- ,.. .-.. , /: I -. II '--~--~ I \ I : PIPE & --t- SUPPORT I II '.... I!-----F=:·=f,--=-=-=--=-:-:1:--U====~=H. ' : ~ ~--··+-'-----''--..U...------LL-...LI p-----' EXISTING VESSEL PLAN ______// I CLIP PSVC-1 PSVC-2 1/8" CLEAR ELEV. Y ' t~~i-.J ' I ELEVATION TYPE M1 M2 I H {MAX} IUSER DEFINED) 1 L4X4X3/8 L3X3X3/8 USER DEFINED 2 C8X11.5 L4X4X3/8 USER DEFINED 3 C10X15.3 C6X8.2 USER DEFINED I PIPE suPPORT MARK No.I NOTE: USER TO DEFINE A, Y AND TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. ~~ESIZE ~~E PNFS021 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 PIPE GUIDE PG-8 (FOR INSULATED PIPING NPS 3 TO 6) 3'-0" MAX. A \ ' \' O.D. OF VESSEL L4X4X3/8X12" LG. 4" --.ISI<-..!.11'-"Be._" CLEAR I '' I EXIST. VESSEL cuP II II II ------c:r-- -,, r---:------- 1 Psvc-1 Psvc-2 II r---1-------1 -----+---: -+----: !.. __ _,: _____ _ '---~:_-- i' (TYP.) , 3 SIDES I' 1/4' EXIST. SHOE (TYP.) I _, •.., 3 SIDES ~ I '' PLAN I ~ BAR DETAIL ' ' I'------ r-- ELEV. Y ' • ' i '' ~ NOTE: USER TO DEFINE A, Y AND TYPE TYPE M1 ELEVATION H ~AX) (USED EFINED) 1 L4X4X3/8 USED DEFINED 2 C6X8.2 USED DEFINED 3 CBX11.5 USED DEFINED PIPE SUPPORT MARK No.I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I PG-B--~~E PNFS021 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS PIPE GUIDE PG-9 (FOR INSULATED VERTICAL PIPING NPS 8 TO 24) OCT 2004 PAGE 1 OF 1 3'-6"(MAX.) b \~\\ O.D. OF VE_S_SE_L_ _ ___ > l,j4"_=____,],._f-=-+----or.t'-.:....1"MIN. F4====F1r=~~~ '' \ '==I===F-=#==;1;=:==1=1= ' ~~~~llNG ~----- \ --------------~--SEE II _____ct__ PIPE ____ _ I PGC-1 /PGC- 2 I~---IF--=1===1=-=--=t=i=~=f:l= • : & SUPPORT II I i:::::=:-:F===l;;;;;;;;;ll;l;;;;;;=*=;;;ll;~ E X I S l l N J h___ VESSEL CLIP PSVC-1 PSVC-2 I PLAN / 1/8" CLEAR ALL AROUND ~ SIDE!¥:---:-:::~-r-7 I '' L __ ELEV. Y ' I '' I ' i '' ~ TYPE M1 M2 ELEVATION H (MAX) (USER DEFINED) 1 L4X4X3/B L3X3X3/B USER DEFINED 2 CBX11.5 L4X4X3/B USER DEFINED 3 C10X15.3 C6X8.2 USER DEFINED I PIPE suPPORT MARK No.I I PG-9--~~E NOTE: USER TO DEFINE A, Y AND TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 PIPE GUIDE CLIPS PGC-1 {ATTACHMENTS FOR GUIDES NPS 8 TO 14) 0 0 0 PLAN-TYPE 1 PNFS025 ocT 2004 PAGE 1 OF 1 0 PLAN-TYPE-2 -- I -- r r--~ B I 'b ELEV. Y I I I 3/B" THICK PLATE l ELEV. A-A I PIPE suPPORT MARK No.I NOTE: USER TO DEFINE B, Y, TYPE AND 4 DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. IPGC-9--~4 TYPE PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 PIPE GUIDE CLIPS PGC-2 (ATTACHMENTS FOR GUIDES NPS 16 TO 24) PLAN-TYPE 1 PNFS0251 ocT 2004 PAGE 1 OF 1 PLAN-TYPE-2 I "k== I ' I ' 'b I ' I I' I I l -- I I x--:::J I I "B"=6" USE WT6X9.5 -- ELEV. A-A I PIPE suPPORT MARK No.I NOTE : USER TO DEFINE Y TYPE AND Q DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. IPGC-2-,.~4 TYPE PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 VESSEL CLIPS PSVC-1 PNFS025 ocT 2004 1 1 PAGE OF ORIENTATION ANGLE e• 1P~ I' Jl CLIP TYPE 1 ELEVATION FOR CLIP TYPES "1" & "2" i ... ,- :I ' ----"---I o ' .., I \ "·. I· I: \ . ·q _j_____ ' ::_ __ _ 'JT '' :p-I: II EL"Y" \ \ "-- : i 'r. \ ' '<+-- I' I' J..J.. ELEVATION FOR CLIP TYPES "3" & "4" CLIP TYPE 3 CLIP TYPE 4 NOTE: USER TO DEFINE A,B,C, W, Y,AND e• DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. METRIC DIMENSIONS IN PARENTHESES ARE IN MILLIMETERS, UNLESS NOTED OTHERWISE. PNFS025 PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 ocT 2004 1 1 PAGE OF VESSEL CLIPS PSVC-2 ORIENTATION ANGLE a' o· I' I' ' I -------l:-....., ' , I / -------.r-t--..... ' I : \ , ' I ' I'\, '"-,, I , ' \ , . I I " _L______ , "' I , / I- \ , , j_/1_ ~- :.' _____L: ' \ o9· \ \ I ' !: ' ............. / ' 1" ALL AROUND I 11' ' ---- r·· o ·o '' j' r- _/ '' lTI' ,. EL."y" I' 4_ CLIP \,,......._ '" \ ---~.!- ' CLIP TYPE 5 MEMBER SIZE =·w· CLIP TYPE 6 ELEVATION FOR CLIP TYPES "5" & "6" ORIENTATION ANGLE e• I' ' _.,....---+<:--......_ I ', , /' : 1 I o ·o I I' I ~: ll CLIP TYPE 7 M~W"MBER \ \, -........ SIZE \ / \ -~---- : I' ( 'I'" \ ' \ I <~> ---~-<X' = ELEVATION FOR NOTIE: "\ ' • '\ "' I \ _[ ______ ' lT I:REL."Y" \ CLIP TYPE 8 CLIP TYPES "7" & "8" 1. USER TO DEFINE A,B,C, W, Y AND e" DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. METRIC DIMENSIONS IN PARENTHESES ARE IN MILLIMETIERS, UNLESS NOTIED OTHERWISE. PNFS035 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CANTILEVER SUPPORT OFF VESSEL PS-1 OCT 2004 PAGE 1 OF 1 2'-6"(MAX.) c \ 4" 1 O.D. OF VESSEL =:...._--\ A I '-+----f-l_l----ir-""Tr -f-T r ~1"----- -------~-~-~----I I I I ID --~--- f I I I ID PIPE 1"MIN (TYP.) PLAN EXISTING VESSEL 3/8" STIFFENER PLATE CLIP PSVC-1 PSVC-2 ELIEV. Y , I I I _____ I C10 OR L4 _]I I I ~ ELEVATION TYPE M1 MAX. LOAD (USER DEFINED) 1 L4X4X3/8 USER DEFINED 2 C10X15.3 USER DEFINED NOTE: USER TO DEFINE A,C, Y AND TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. SUPPORT PNFS0351 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 KNEE BRACE SUPPORT OFF VESSEL PS-2 c \ O.D. OF VESSEL 4" I I I PIPE--- I 1 INSULATION ID L3X3X3/8 SUPPORT --~------ "'<~ 1 I u • "' ---.t.i'--- f ~ 1"MIN.(TYP) PLAN EXISTING VESSEL CUP EUEV. Y c (TYP.) ELEVATION TYPE 1 M1 L4X4X3/8 M2 L3X3X3/8 MAX. LOAD DEFINED) I (USER USER DEFINED NOTE: USER TO DEFINE A,B,C,D, Y, etc DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. ID PNFS035 PROCESS INDUSTRY PRACTICES FABRICATION/I NSTALLATIO N DETAILS OCT 2004 PAGE 1 OF 1 KNEE BRACE SUPPORT OFF VESSEL PS-3 \ \ 0.D. OF '+--#--1-- VESSEL~ L3X3X3/8 III PLAN EXISTING VESSEL CLIP PSVC-1 PSVC-2 ELEV. Y 0 ~----------------~~~ I I I ~---J TYPE 1 M1 4-C8X11.5 ELEVATION M2 2-WT4X9 MAX. LOAD (USER DEFINED) USER DEFINED NOTE: USER TO DEFINE A,B,C,D, Y,etc DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. METRIC DIMENSIONS IN PARENTHESES ARE IN MILLIMETERS, UNLESS NOTED OTHERWISE. PNFS035 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SINGLE KNEE BRACE SUPPORT OFF VESSEL PS-4 OCT 2004 PAGE 1 OF 1 3'-0" (MAX.) \ Cl SUPPORT I I O.D. OF VESSEL I I PLAN I c A ELEV. Y 1/4" c ELEVATION TYPE 1 M1 L4X4X3/8 M2 L3X3X3/8 MAX. LOAD (USER DEFINED) USER DEFINED NOTE: USER TO DEFINE A,C,D, Y,etc DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS035 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS KNEE BRACE SUPPORT OFF VESSEL PS-5 OCT 2004 PAGE 1 OF 1 4'-0"(MAX.) \ O.D. OF VESSEL c I I I 1 PIPE I INSULATION SUPPORT --~------ 1 I --tt-- 1"MIN.(TYP.) PLAN ' /-l p 3/8" STIFF. PLA1lE ~I I EXISTING VESSEL CUP , PSVC-2 PSVC-1/ ----1 ~t!a~~~~~t~~~~~r="'=t-~~ I c 1/4 ELEVATION ' TYPE M1 M2 MAX. LOAD (USER DEFINED) 1 C10X15.3 WT4X9 USER DEFINED NOllE : USER TO DEFINE A,B,C,D, Y,etc DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS035 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CANTILEVER SUPPORT OFF VESSEL PS-6 {ROUND TYPE CLIPS) OCT 2004 PAGE 1 OF 1 3'-0" (MAX.) c ID ' --4-------!~---~~---~q~l--+ ' PIPE INSULATION ID 1"MIN. {TYP) I PLAN . . . . . _ __ _/ _____1 EXISTING VESSEL CLIP PSVC-2 p ' I' '' I I ' I' .........._ __ _/-----~' ELEVATION MAX. LOAD (USER DEFINED) TYPE M1 1 W6X12 USER DEFINED 2 WBX18 USER DEFINED I I PIPE suPPORT MARK No.I NOTE: USER TO DEFINE A,B,C, Y AND TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I PS-6--~ \_c AB PNFS035 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 KNEE BRACE SUPPORT OFF VESSEL PS-7 c ID ' ------------+-------.W.r·--·""'-!--o'"---l:'?l~--1------------'l.-$--"-uJ::!:\!!!!... ' ID PIPE INSULATION 1"MIN. (TYP.) PLAN p EXISTING VESSEL CLIP PSVC-2 3/8" STIFFENER PL. c ELEVATION TYPE M1 M2 MAX. LOAD (USER DEFINED) 1 W4X13 W4X13 USER DEFINED 2 W6X15 W4X13 USER DEFINED I PIPE suPPORT MARK No.I NOllE : USER TO DEFINE A,B,C,D, Y, TYPE, etc DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. I PS-7- - - - ~D ~: PNFS035 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SINGLE KNEE BRACE SUPPORT OFF VESSEL PS-8 {ROUND TYPE CLIPS) OCT 2004 PAGE 1 OF 1 4'-0" MAX. I '' O.D. OF VESSEL .-}-=~=~~-=~=~~t'=~53-'I I' PLAN I i A C 3/8" STIFFENER PLATE ELEV. Y --t-BEAM & CLIP c 1/4" ELEVATION TYPE M1 M2 MAX. LOAD (USER DEFINED) 1 W4X13 WT4X9 USER DEFINED 2 W6X15 WT4X9 USER DEFINED I PIPE suPPORT MARK No.I NOTE: USER TO DEFINE A,C,D, Y AND TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I PS-8-T~~'\._D Ac TYPE PNFS036 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 CANTILEVER BRACKETS PS-16 (FROM ADJACENT STEEL OR VESSEL) A A 1"MIN. 2' -6" --~-- ~ 1"MIN. 2'-6" t II II EL. y EXIST. COL. II II EL. y t::J -========== EXIST. COL. TYPE 1 TYPE 2 A A 2'-6" r'l...\r--.- (MAX.) (MAX.) p p EL. y EL. y EXIST. COL. EXIST. COL. TYPE 4 TYPE 3 TYPE MEMBER SIZE (IMAX.LOAD (PJ) USER DEFINED 1 C8X11.5 USER DEFINED 2 C8X11.5 USER DEFINED 3 W6X12 USER DEFINED 4 W6X12 USER DEFINED NOTE: USER TO DEFINE A, Y,AND TYPE I PIPE suPPORT MARK No.I I PS-16--~A DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. TYPE PNFS036 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 KNEE BRACED BRACKETS PS-17 (FROM ADJACENT STEEL.) A A c 4'-0" MAX. 4'-0" MAX. EXIST. COL. EXIST. COL. I I II I II II ill TYPE 1A OR 1B TYPE TYPE 2A OR 2B M1 M2 MAX LOAD (USER DEFINED) 1A W6X15 WT4X9 USER DEFINED 18 W4X13 L3X3X3/8 USER DEFINED 2A W6X15 WT4X9 USER DEFINED 28 W4X13 L3X3X3/8 USER DEFINED NOTE : USER TO DEFINE A,C, Y AND TYPE DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. c PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS KNEE BRACE BRACKETS FROM ADJACENT STEEL PS-18 PNFS036 ocT 2004 1 0 1 t--PA_G_E__ _F__ _-----l A A c TYPE 1 1/4" II II COPE SHARP EDGE __;' TYPE 2 TYPE 1 M1 M2 MAX. LOAD (USER DEFINED) L6X4X1/2 L4X4X1/2 USER DEFINED L6X4X1/2 2 NOTE: USER TO DEFINE A,C,D, Y AND TYPE L4X4X1/2 USER DEFINED DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PNFS036 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 T-SUPPORT PS-19 {FROM ADJACENT STEEL) A P2 L ro· 1 {MAX.) 1 1 {MAX.) • -~ EL. y WT5X11 6XB.2 ~ 1/4"V WT5X11 1/4" -~ I EXISTING _ _ _ _;nl CHANNEL I •0 I ;,. ~J =-=--====t EE DETAIL FOR ALT. CONN. 1/4" --=------ ----=-- DETAIL OF EXISTING BEAM OR CHANNEL ALTERNATE CONNECTION ======== TYPE 1 ======== OR CHANNEL EXISTING BEAM F-= x < ::::E ID 1;4·V •0 ·-=-= v ~~R ALT. CONN. EE DETAIL I ;,. WT5X11 - 8.2 1/4"171~ P3 h.C6X y ' • ~ {MAX.) {MAX.) 1'0" 1'0" A NOTIE : 1. USER TO DEFINE A,B, Y,ect, TYPE 2. P1,P2 AND P3 SHALL BE DEFINED BY USER TYPE 2 I PIPE suPPORT MARK No.I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SINGLE COLUMN BRACKET PS-20 (FROM EXISTING STEEL) PNFS0369 OCT 2004 PAGE 1 OF 1 A 5'-0" MAX A/2 p W6X15'\_ ~ EL. y 1\ X m < :::. •0 .!'- (TYP.) d: I/1;4·V -:.-:. l -----usER :I II I: :I II II II t W6X15 II II _j : 1/4"v I in 1--' ..-- SEE ALT CONN "A" '• -------- TO DETERMINE IF EXISTING COL. ,........00::'---'11-'- II II ALT. CONN. "A" :rU EXIST. STEEL GUSSETING OF EXIST. STEEL IS REQUIRED ELEVATION TYPE 1 41 .:---- ==-=..= =---- -- --- _E_X,IS__T._S_TE,-E-C_ F~==------========---11 \! X < m • W6X15 l/4.v :::. 0 A/2 I II II II I II ':·) 5'-0" MAX I I II II I! !! I II /'~/4" V .:!EL~-~y-~----tr-t~/==== !================'==4 in p W6X15""\. I SEE ALT CONN "A" A • ELEVATION NOTE: 1. P(MAX.) 0 MIDSPAN=5.0 KIPS 2. TYPE2 USER TO DEFINE A,B, Y AND TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS037 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 DOUBLE COLUMN BRACKET PS-21 (FROM EXISTING STEEL) A (5'-0" MAX) A/2 1 W6X15 ':... -'1<---rr-n EL. y F=================~ ~ X m < W6X15 :::. W6X15 'b I ;, ~ --~------------ EXIST. STEEL USER TO DETERMINE IF GUSSETTING OF EXISTING STEEL IS REQUIRED. ELEVATION TYPE 1 EXIST. STEEL .!-- ======================= r-- - - --:::::: =:::::: =:::::: =:::::: =:::::: - - '\ "~ m , _ , , " ~~"--v: V - --.::-.::- ~ ~ OF EXISTING STEEL IS REQUIRED. . ~ X (TYP.) W6X15 •V 1/4" m W6X15 I ~ p EL. y ':... "-wsx15 A/2 A ( 5'-0" MAX ) NOTE: 2. USER TO DEFINE A,B, Y & TYPE. •0 ;, ~(TYP.) . 1. P(MAX.) 0 MIDSPAN = 5.0 KIPS < ::E ELEVATION TYPE2 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. ~ PNFS0371 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 SLIDE PLATE ASSEMBLY PS-22 EXIST. SHOE OR TRUNNION LOWER ELEM::.:E::..:N.:...T- - - , 7/111"-SLIDING SURFACE IL__: I +___ 7 _______ _ I 1 - - - - - - - - - - - - - - - - -->..'I.---------+ ----~ PLATE SHAUL BE WEUDED WITH SKIP AND FIUL TECHNIQUE 1/8" FIULET WELDS, 1/4" TO 1/2" LONG, ON 6" CENTERS AROUND THE PERIPHERY OF BASE METAL UNTIL PLATE IS COMPLETELY SEAL WELDED. ~o.uLI~ EXISTING STRUCTURAL MEMBER _ _ / ELEVATION 't, !t, 1/8" LIP SUPPORT I i C.S. PLATE SUPPORT 1/8" LIP I i (TYPJ c.S. ' PLATE ' ! SUPPORT ------& TRUNNION OR SHOE POLISHED S.S. PLATE ! I ' r- ---~--r-· - ' v .)> ----:-- (TYP.) I I ID ' --- -- --~' ;, ' I I / TEFLON /GRAPHITE -- c I ' I I c A UPPER ELEMENT LOWER ELEMENT I PIPE suPPORT MARK No.I I PS-22-,..~~D NOTE : USER TO DEFINE A,B,C & D DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. AB TYPE PNFS037 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 ROD HANGERS PS-23 < TYPE 2 TYPE 1 TYPE 3 UPPER ATTACHMENTS ~~~:!JNE lHREADED ROD (DIA. "D") t CLEVIS Bl ~ ~ I /-,.,;e -~--t 3 VIEW 8-8 TYPE 4 TYPE 6 LOWER ATTACHMENTS NOTE: 1. USER TO DEFINE A, D, Y AND TYPE 2. CLAMP AND BOLT MATERIAL PER MSS SP-58 PER OPERATING TEMPERATURES. DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. UPPER TYPE PNFS037 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 ADJUSTABLE BASE SUPPORT PS-24 (FOR NPS 3 THRU. 16) I....___I - - - -EXIST. TRUNNION & BASE PLATE ....,::;r=:::;:::::F';:!.._---SioE PLATE "C" DETAIL - 1 - - - - - - " A " DIA. THR'D ROD •0> I ..J,.4.,J....j----~ HEAVY HEX NUTS TO 1MATCH ROD "A" t----;--;J;;:-j-~!;::;:~;!;:;~----SEE PLATE "D" DETAIL 1 - - - - - - " 8 " DIA. PIPE SCH.BO MIN . •<0 T.O.GROUT EXIST. CONCRETE PIER OR PAVING ELEVATION ROD "A"+1/B" 1/2" d t • "' + in ---- ~ ~ ~ - - • ' I I 1/2" ROD "A" t 1 1/4" 1/2"t d i -- I ~- "' ---~ .. d "' i I • 1 1/4" (TYP) I PLATE "C" PLATE "D" ~N~ ~N~ PLATE "E" ROD~~~~· "A" IN "8" STt~fHIONS ~~~~ TYPE 3 1 6X6X1/2 SEE DETAILS BXBX1/2 1 1/4 2 4 & 6 2 6X6X1/2 SEE DETAILS BXBX1/2 1 1/2 3 B TO 12 3 6X6X1/2 SEE DETAILS BXBX1/2 2 4 14 TO 16 4 BXBX1/2 SEE DETAILS 10X10X1/2 2 1/2 6 M IPIPE suPPORT MARK No.I I PS-24-TJ DIMENSIONS ARE GI~N IN FEET AND/OR INCHES. "'-TYPE PNFS037 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 STANDARD U-BOLT PS-25 c c 8 A w c GUIDE ANCHOR TYPE 2 TYPE1 ROD SIZE A 8 c D E 3 1/2 3 9/16 4 1/16 4 3 4 1/2 4 9/16 5 1/16 4 1/2 3 6 5/8 6 3/4 7 3/8 6 1/8 3 3/4 8 5/8 8 3/4 9 3/8 7 1/8 3 3/4 10 3/4 10 7/8 11 5/8 8 3/8 4 12 7/8 12 7/8 13 3/4 9 5/8 4 1/4 14 7/8 14 1/8 15 10 1/4 4 1/4 16 7/8 16 1/8 17 11 1/4 4 1/4 18 1 18 1/8 19 1/8 12 5/8 4 3/4 20 1 20 1/8 21 1/8 13 5/8 4 3/4 24 1 24 1/8 25 1/8 15 5/8 4 3/4 NPS DIM. IN INCHES I PIPE suPPORT MARK No.I I PS-25-"{_ DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. NPS PNFS037 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 T-SUPPORT PS-26 (FROM GRADE) EL. y A ~,: 1 W4X13 TYPE 1 1' -o· ._ 1' -o'" MAX. P3 W6X15 TYPE 2 I 1 MAX. P1 I ! I ,' TOP OF GRADE OR PIER ~ t II ~ 1;4·V SECTION C-C L 1" GROUT 3/4" DIA. XS 1/2" LG. CINCH ANCHORS ELEVATION (BY FIELD) TYPES 1 & 2 ,-1'-L---+-----.I',L___ ' ' 4-13/16" DIA. HOLES IN PLATE PL. 1/2"X1 O"X1 0"- TYPE 1 PL. 1/2"X12"X12"- TYPE 2 1/4" DESIGN LOAD SECTION 8-8 VERT. LOAD: P1 = USER DEFINED VERT. LOAD: P2 ONLY OR P3 ONLY = USER DEFINED VERT .LOAD: P1 + P2 + P3 COMBINED = USER DEFINED I PIPE suPPORT MARK No.I NOTE: USER TO DEFINE A,B, Y AND TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I PS-26-~B TYPE PNFS037 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 CONTAMINATION PREVENTION PLATE PS-27 ,-------------------~" I I -K--------------~ I I I I \/ I I I I \/ ------ II II ~ 1/4" TYP. 8 "C" lHK. STAINLESS STEEL PLATE A A = NOM. PIPE DIAMETER (2" MIN.) (10" MAX.) NOTE: FOR PREVENTION OF ZINC CONTAMINATION FROM GALV. STRUCTURAL STEEL TO STAINLESS & NICKEL PIPING. I PIPE suPPORT MARK No.I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I PS-27-.- - \_ ~8 C A PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 HANGING T-SUPPORT PS-28 (FOR NPS 3 THRU 6) PNFS037 ocT 2004 PAGE 1 OF 1 (LOAD LIMIT=USER DEFINED) 1-----------------1 ~-- L3x3x1/4 1/4" < EL. y L 1 8 l c L 1 ELEVATIONl II II TYPE.1 NOTE: TYPE.2 DETAIL OF ALTERNATE CONNECTION I PIPE suPPORT MARK No.I USER TO DEFINE A, 8, C, Y. I PS-28--~------ \__c A8 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. TYPE PROCESS INDUSTRY PRACTICES I-----F_A_8_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--l HANGING TRAPEZE FROM EXISTING CHANNEL PS-29 (FOR NPS 3 THRU 12) PNFS037 ocT 2004 1 1 PAGE OF ~---===::--=-===--=::-~---===::--=-===--=::-~--=-===::--=-===--=:: y L_ ~ / (1YP.) :~ -- 1----------------------1 ID ""'~ ~~~-----_--_---_--_--_---_--_--_---_--_------~~-~- I (1YP. ) .v~I ii ELEV. Y ....--- l 1 l 1 A l 4 1/2" 1 TYP. ELEVATION 1/4 EXISTING CHANNEL LOAD LIMITS TYPE LOAD LIMIT (USER DEFINED) ITEM 1 L3X3X3/B USER DEFINED 2 L4X4X5/16 USER DEFINED 3 L6X4X3/B USER DEFINED SECTION 8-8 I PIPE suPPORT MARK No.I I DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PS-29-~- - ~ ""> \._~E PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 CANTILEVER BRACKET FROM EXISTING STEEL PS-30 PNFS0379 ocT 2004 1 0 1 t--PA_G_E__ _F__ _-----l "A• "D" •Ill • :; PLAN TYPE 1 •Ill • BOLTED CONN. (TYP.) (USE 3/4" DIA. BOLTS) ~ ~~EXISllNG 1,~ v \ :~: STEEL ELEV. Y NOTE: 1. TYPE 1 DOES NOT INCLUDE THE INNER ANGLE MEMBER. TYPE 2 INCLUDES IT. 2. USER TO DEFINE DIMENSIONS A, B, C, D, Y, AND TYPE. ELEVATION 3. LOAD = USER DEFINED DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 SINGLE CANTILEVER FROM EXISTING STEEL PS-31 1 PNFS038 ocT 2004 1 1 PAGE OF A C~--:1;:1-_:-.:.:--, .- ~==============~t MEMBER SIZE --=E=LEc:..:.V. ....:.Y_ __ •c• 1/4" ELEVATION TYPE A EXIST. BEAM r MEMBER SIZE ELEV. Y •c• 1/4" ELEVATION TYPE 2 --,,,-- A I c-- -~--- :::J q: --il i _E_X_IST_._B_EA_M_ _ ELEV. Y MEMBER SIZE •c• ELEVATION TYPE 3 NOTE: USER TO DEFINE DIMENSIONS A, C, Y, AND TYPE. I PIPE suPPORT MARK No.I DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. I PS-31- -~A c \__~E PNFS040 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 PIPE SHOE S-2 {FOR NPS 3 TO 8) 1/2" ----.ir-+-~oi'-- (TYP.) INSULATION (TYP.) (TYP.) BANDING SLOTS L 4" END VIEW SIDE VIEW TYPE H L MEMBER SIZE 1 4 12 WT4X7.5 2 4 18 WT4X7.5 3 6 12 WT6X9.5 4 6 18 WT6X9.5 NOllE: IF STRUCTURAL SHAPE IS NOT AVAILABLE IN SPECIFIC MA llERIAL FABRICAllE SHOES FROM 1/4" PLAllE. WELDS TO BE 1/4" FILLET. I PIPE suPPORT MARK No.I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I PS-2-<L TYPE PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS PIPE SHOE S-3 {FOR NPS 3 TO 8) PNFS0401 OCT 2004 PAGE 1 OF 1 (SEE NOTE) f-~-< (TYP.) 3" 1/2" (TYP.) SEE TABLE FOR SHOP CUT TO MEMBER SIZE FIT CONTOUR 3"' 1/4" (TYP.) 1" 2" (TYP.) BANDING SLOTS OF PIPE L SIDE VIEW END VIEW TYPE H L MEMBER SIZE 1 4 12 WT4X7.5 2 4 18 WT4X7.5 3 6 12 WT6X9.5 4 6 18 WT6X9.5 NOTE: 1. SPECIAL SHOE USED FOR GUIDES AND DIRECTIONAL STOP ONLY. 2. IF STRUCTURAL SHAPE IS NOT AVAILABLE IN SPECIFIED MATERIAL FABRICATE SHOES FROM 1/4" PLATE. WELDS TO BE 1/4" FILLET. IPIPE suPPORT MARK No.I I S-3--tTYPE DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PNFS040 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 PIPE SHOE S-4 (FOR NPS 10 AND 12) 18" SHOP TO lRIM BEAM SECllONS SEE TABLE FOR SIZES 3" 1/2" (TYP.) (TYP.) r--I I I I --'f- ~-- I I B.O.P. ---t---_/ 1/2" (TYP.) ,Jll,. (TYP.) END VIEW NPS INSULAllON BANDING SLOTS (TYP.) SIDE VIEW MEMBER SIZE TYPE H H1 1 4 5 3/8 W8X24 2 6 7 3/8 W8X31 3 4 5 W8X24 4 6 7 W8X31 10 12 NOTE: IF STRUCTURAL SHAPE IS NOT AVAILABLE IN SPECIFIED MATERIAL FABRICATE SHOES FROM 3/8" PLATE. \\£LOS TO BE 1/4" FILLET. I PIPE suPPORT MARK No.I I S-4-_J DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. '-TYPE PNFS040 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2003 PAGE 1 OF 1 PIPE SHOE S-5 (FOR NPS 14 TO 24 WITH LESS THAN 4" INSUL.) SHOP TO TRIM BEAM SECTIONS SEE TABLE FOR SIZES 18" 3" 1/2" ......--.1'+-----.t(TYP.) (TYP.) --A I I --~I I B.O.P. --1---_/ 1/2" (TYP.) 3/8" Jll. 1/2" II!. w (TYP.) BANDING SLOTS (TYP.) END VIEW SIDE VIEW NPS TYPE H H1 w MEMBER SIZE 14 1 4 4 13/16 10 W8X24 16 2 4 4 5/8 10 W8X24 18 3 4 5 1/16 12 W10X22 20 4 4 4 7/8 12 W10X22 24 5 4 4 5/8 12 W10X22 I PIPE suPPORT MARK No.I I S-5- J DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. '-TYPE PNFS040 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS PIPE SHOE S-6 {FOR NPS 14 TO 24 WITH INSUL. >= 4" AND OCT 2004 PAGE 1 OF 1 < 6") 18" 1/2" 3" "...,--,H----.1' (TYP.) (TYP.) --7\ I I --~I I B.O.P. --j---_j 1/2" (TYP.) 1/2" PLATE w BANDING SLOTS SHOP TO TRIM BEAM SECTIONS SEE TABLE FOR SIZES END VIEW SIDE VIEW NPS TYPE H H1 w 14 1 6 6 3/4 10 W8X31 16 2 6 6 9/16 10 W8X31 18 3 6 6 15/16 12 W10X33 20 4 6 6 3/4 12 W10X33 24 5 6 6 1/8 12 W10X33 MEMBER SIZE I PIPE suPPORT MARK No.I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I S-6-X_TYPE PNFS040 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 PIPE SHOE - (CLAMP TYPE) S-7 (FOR PIPE NPS 3 TO 8) L ~-- 1 PIPE CLAMP TYPE PER MSS SP-58 I( 3" LFOR 12" LONG SHOE 6" 6" lFOR 18" LONG SHOE --CP~ _ _ _[--_ Q_ B.O.P. ~-r~--~~-h~ SEE TABLE FOR MEMBER SIZE •J: ' NSULAllON BANDING SLOTS 4" "L" END VIEW SIDE VIEW NPS TYPE H L MEMBER SIZE 1 4 12 WT4X7.5 2 4 18 WT4X7.5 3 6 12 WT6X9.5 4 6 18 WT6X9.5 3" TO a· NOllE: IF STRUCTURAL SHAPE IS NOT AVAILABLE IN SPECIFIED MAllERIAL, FABRICAllE SHOES FROM 3/8" PLAllE. WELDS TO BE 1/4" FILLET. I PIPE suPPORT MARK No.I ls7~ DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. NPS TYPE PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS PIPE SHOE-(CLAMP TYPE) S-8 {FOR PIPE NPS 10 AND 12) PNFS040 OCT 2004 PAGE 1 OF 1 PIPE CLAMP //---- 4 PER MSS SP-58 .) 3/B" PLATE 10" END VIEW SIDE VIEW NPS TYPE H H1 MEMBER SIZE 1 4 4 7/B WBX24 2 6 6 7/B W8X31 3 4 4 1/2 WBX24 4 6 6 1/2 WBX31 10 12 NOTE: IF STRUClURAL SHAPE IS NOT AVAILABLE IN SPECIFIED MATERIAL FABRICATE SHOES FROM 3/8" PLATE. WELDS TO BE 1/4" FILLET. I PIPE suPPORT MARK No.I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. ~NPS TYPE PNFS040 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 PIPE SHOE-(CLAMP TYPE) S-9 (FOR PIPE NPS 14 TO 24) g• 9" PIPE CLAMP 4 PER MSS SP-58 B.O.P. 3/8" PLATE 10" INSULATION BANDING SLOTS END VIEW SIDE VIEW NPS TYPE H H1 w MEMBER SIZE 14 1 4 4 5/16 10 W8X24 16 2 4 4 1/8 10 W8X24 18 3 4 4 7/16 12 W10X22 20 4 4 4 1/4 12 W10X22 24 5 4 4 12 W10X22 NOTE: IF STRUClURAL SHAPE IS NOT AVAILABLE IN SPECIFIED MATERIAL FABRICATE SHOES FROM 3/8" PLATE. \\£LOS TO BE 1/4" FILLET. I PIPE suPPORT MARK No.I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. ~NPS TYPE PNFS045 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 SPRING HANGER ASSEMBLY TYPE C, SH-1 (FOR BARE PIPE) ----r--1 EXIST. STEEL I B.O.S. EL. '---l't£LOING LUG GRINNELL FIG. 55 OR EQUAL 1------ GRINNELL SPRING OR EQUAL SIZE TYPE- C FIG. NO. OPERATING LOAD- _ _ __ COLO LOAD-_ _ _ __ MOVEMENT - - - HYDRO. TEST LOAD - - - - 1 - - - - - - - - MACHINE THREADED ROD GRINNELL FIG. 140 OR EQUAL l't£LDLESS EYE N U T - - - - - - . . . GRINNELL FIG. 290 OR EQUAL ==• PIPE CLAMP GRINNELL FIG. 212 OR EQUAL NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG NO. _ _ _ __ LOCATION DWG./ISO NO. _ _ __ LINE NO. _ _ _ _ _ _ _ __ DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SPRING HANGER ASSEMBLY TYPE C, SH-2 (FOR INSULATED PIPE) PNFS0451 OCT 2004 PAGE 1 OF 1 ----~--- EXIST. STEEL B.O.S. EL. ' - - - - WELDING LUG GRINNELL FIG. 55 OR EQUAL 1/4" 1~---- GRINNELL SPRING OR EQUAL SIZE---- TYPE- C FIG. NO. OPERAllNG LOAD COLD LOAD MOVEMENT - - - HYDRO. TEST LOAD 1-------- MACHINE THREADED ROD GRINNELL FIG. 140 OR EQUAL WELDLESS EYE NUT--------._ GRINNELL FIG. 290 OR EQUAL ==;;- PIPE CLAMP GRINNELL FIG. 295 OR EQUAL ...t,EJ:·== NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG N O . - - - - LOCAllON DWG./ISO NO. _ _ __ LINE NO. _ _ _ _ _ _ _ __ DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SPRING HANGER ASSEMBLY TYPE C, SH-3 {FOR ALLOY CLAMP) PNFS045 OCT 2004 PAGE 1 OF 1 ----~--- EXIST. STEEL B.O.S. EL. "\....__ WELDING LUG GRINNELL FIG. 55 OR EQUAL 1------ GRINNELL SPRING OR EQUAL SIZE-_ _ __ TYPE- C FIG. NO. OPERATING LOAD COLD LOAD - - - - MOVEMENT- _ _ __ HYDRO. TEST LOAD - - - - 1 - - - - - - - MACHINE THREADED ROD GRINNELL FIG. 140 OR EQUAL WELDLESS EYE N U T - - - - - - - . . . GRINNELL FIG. 290 OR EQUAL /"'' ;<;;=;:;-;- PIPE CLAMP GRINNELL FIG. 224 OR EQUAL NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG NO. _ _ _ _ __ LOCATION DWG./ISO NO. _ _ __ UNE NO. _ _ _ _ _ _ _ __ DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SPRING HANGER ASSEMBLY TYPE C, SH-4 (WITH WELDING LUG TYPE) PNFS045 OCT 2004 PAGE 1 OF 1 ~======~ EXIST. STEEL B.O.S. EL. WELDING LUG GRINNELL FIG. 55 OR EQUAL 1/4" GRINNELIL SPRING OR EQUAL SIZE-_ _ __ TYPE- C FIG. NO.-_ _ __ OPERATING LOAD - - - COLD LOAD - - - MOVEMENT- _ _ __ HYDRO. TEST LOAD - - - MACHINE THREADED ROD GRINNELL FIG. 299 OR EQUAL ~--- GRINNELIL FIG. 140 OR EQUAL . - - - - - - LOCK NUT l _ __ '""= ~l=~ -----t=T=J ' _____ J=t-----m--- -~if1 1~ : I I : I I~ VIEW B-B VIEW A-A NOTE: 1. BLANKS TO BE FILLED BY USER. ALTERNATE PIPE ASSEMBLY TAG NO. _ _ _ __ LOCATION DWG./ISO NO. _ _ __ LINE NO. _ _ _ _ _ _ _ __ I ATTACHMENT DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS045 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SPRING SUPPORT ASSEMBLY TYPE F, SH-5 (BASE TYPE AT GRADE) OCT 2004 PAGE 1 OF 1 I m I I I :1l ~/ /~/c/1 -trt:?t~~: fff -::=s--EXIST. TRUNNION OR SHOE I I SLIDING SURFACE T.O.GROUT EL EXIST. CONCRETE PIER OR PAVING P.O.S. EL. OR EQUAL SIZE- _ _ __ FIG. NO.- _ _ __ TYPE- F OPERATING LOAD ..F.::...:ji.r.+..;;,~.\~b- COLD LOAD- _ _ _ __ MOVEMENT- _ _ __ HYDRO. TEST LOAD- _ _ __ (4) 3/4" DIA. X 5 1/2" LG. CINCH ANCHOR BOLTS FOR SPRING SIZE UPTO SIZE 2 , THE BOLT SIZE SHALL BE 5/B" DIA. {BY FIELD) NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG N O . - - - - LOCATION DWG./ISO NO. _ _ __ LINE N O . - - - - - - - - DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS045 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SPRING SUPPORT ASSEMBLY TYPE F, SH-6 (BASE TYPE AT GRADE WITH SLIDE PLATE) OCT 2004 PAGE 1 OF 1 Fn : I : J--H ~E_EL.=~= f -- /1 ;'J1' _____ =s _ _-t-~~~f_l_ -Tt-LL ____ _ ------~~ 1~ -- --EX~T~ : I 1 TRUNNION OR SHOE 7 /16" {FOR SLIDE PLATE SEE PNFS0371) I P.O.S. EL. OR EQUAL SIZE- _ _ __ FIG. NO.- _ _ __ T.O.GROUT E TYPE- F OPERATING LOAD COLD LOAD- _ _ _ __ MOVEMENT - - - HYDRO. TEST LOAD-_ _ __ {4) 3/4" DIA. X 5 1/2" LG. CINCH ANCHOR BOLTS FOR SPRING SIZE UPTO SIZE 2 , THE BOLT SIZE SHALL BE 5/B" DIA. (BY FIELD) NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG N O . - - - - LOCATION DWG./ISO NO. _ _ __ LINE N O . - - - - - - - - - DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ') SPRING SUPPORT ASSEMBLY TYPE F, SH-7 {BASE TYPE FROM STEEL) PNFS0456 OCT 2004 PAGE 1 OF 1 m ,'~ I I I / j,~ ct. PIPE _E~:::L.==-=c=---- - -----=s tr _,0i- -t~=~fir-: --7+- - L --- --- -- - I SLIDING SURFACE l I I EXIST. TRUNNION OR SHOE l ±l P.O.S. EL. GRINNELL SPRING 1/4Vi- \ ..!.T~.O!.:.S!:....EEL!,o·===------1.~---EXIST. STEEL """ ~::;:!:::;:j:;::::!?::: -;,.- T I r-- __ --I-__ r-- - -~- - J OR EQUAL SIZE.- _ _ _ __ FIG. NO.- _ _ __ ~~~~G LOAD COLD LOAD- _ _ __ MOVEMENT- _ _ __ HYDRO. TEST LOAD- _ _ __ NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG NO. _ _ __ LOCATION DWG./ISO NO. _ __ LINE NO. _ _ _ _ _ __ DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. ') PNFS0457 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SPRING SUPPORT ASSEMBLY TYPE F, SH-8 {BASE TYPE FROM STEEL WITH SLIDE PLATE) OCT 2004 PAGE 1 OF 1 m : I : ,4l //1 ;,'~' ~E_E=:.=L.=-=----tr~~ I ~:?Lf~~ -~~j--- frtI I I "1<--c------~- ~~ <(" Iii iii ~:I: ==- d--::;:,~JJ.--~P.O::_:.S:._.::EL::.=. -t- 7/16" (FOR SUDE PLATE SEE PNFS0371) I 1/ 1/4". 1-2 I -To~.o~.s~.~E=L.====~--~r----EXIST. STEEL -~ EXIST. TRUNNION OR SHOE I T1 .....:',.- == J =F == 1 GRINNEUL SPRING OR EQUAL SIZE- _ _ __ FIG. NO.TYPE- F OPERATING LOAD- _ _ __ COUD LOAD·-----MOVEMENT-_ _ __ HYDRO. TEST LOAD·------ I NOTE: 1. BLANKS TO BE FIULED BY USER. ASSEMBLY TAG NO._ _ _ __ LOCATION DWG.(ISO NO. _ _ __ UNE N O . - - - - - - - - DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CONSTANT SPRING HANGER ASSEt.iBLY TYPE C, SH-9 {FOR BARE LINE) PNFS045 OCT 2004 PAGE 1 OF 1 EXIST. STEEL ___ _l __ _ B.O.S. EL. WELDING LU'-"G,__~/-- -~.::m~±=:~ GRINNELL FIG. 55 OR EQUAL _____ GRINNELL CONSTANT !OR EQUAL SPRING SIZE- _ _ __ FIG. NO.-C-80-V MODEL R TYPE- C CONSTANT LOAD TOTAL TRAVEL - - - ACTUAL TRAVEL - - - ROD DIA. "J" HYDRO. TEST LOAD- _ _ __ MACHINE THREADED ROD 1 1 - - - - - - - GRINNELL FIG. 140 OR EQUAL WELDLESS EYE NUT·--------._ GRINNELL FIG. 290 OR EQUAL _ __riPE CLAMP NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG NO. _ _ _ _ _ __ LOCATION DWG/ISO N O · - - - - - LINE N O · - - - - - - - - - - DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CONSTANT SPRING HANGER ASSEMBLY TYPE C, SH-10 {FOR INSULATED LINE) PNFS0459 ocT 2004 1 0 1 I--PA_G_E__ _F__ _---l EXIST. STEEL B.O.S. EL. OR EQUAL GRINNELL CONSTANT SPRING OR EQUAL SIZE FIG. NO.-C-80-V MODEL R TYPE- C CONSTANT LOAD- _ _ __ TOTAL TRAVEL- _ _ __ ACTUAL TRAVEL- _ _ __ ROD DIA. " J " - - - - HYDRO. TEST LOAD MACHINE THREADED ROD WELDLESS EYE N U T - - - - - - - . . GRINNELL FIG. 290 OR EQUAL GRINNELL FIG. 140 OR EQUAL ~,-------LOCK NUT GRINNELL FIG. 295 OR EQUAL NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG NO _ _ _ _ __ LOCATION DWG/ISO NO _ _ _ __ UNE N O . - - - - - - - - - DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CONSTANT SPRING HANGER ASSEMBLY TYPE C, SH-11 (WITH ALLOY CLAMP) PNFS046 ocT 2004 1 0 1 t--PA_G_E__ _F__ _-----l EXIST. STEEL S.O.S. EL WELDING LU'-"G'--__, GRINNELL FIG. 55 OR EQUAL 1-------G.:c:R.;;;IN.c.N.:.::E::::LL::.....:..::;CONSTANT SPRING OR EQUAL SIZE- _ _ __ FIG. NO.-C-80-V MODEL R TYPE- C CONSTANT LOAD TOTAL TRAVEL - - - ACTUAL TRAVEL - - - ROD DIA. "J''- ---- HYDRO. TEST LOAD- _ _ __ MACHINE THREADED ROD GRINNELL FIG. 140 OR EQUAL WELDLESS EYE ' . . ! ! . - - - - - - - L O C K NUT GRINNELL FIG. 290 OR EQUAL GRINNELL FIG. 224 OR EQUAL NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG NO. _ _ _ _ _ __ LOCAllON DWG/ISO NO. _ _ _ __ LINE N O . - - - - - - - - - - DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0461 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ocT CONSTANT SPRING HANGER ASSEMBLY TYPE C, SH-12 (WITH WELDING TYPE LUGS) 2004 1 0 1 t--PA_G_E__ _F__ _-----l EXIST. STEEL S.O.S. EL I~ELDING LUG GRINNELL FIG. 55 OR EQUAL 1/4" 1-------'G:':R:::.IN:;:N;=ELL==,..:C:::ONSTANT SPRING OR EQUAL SIZE- _ _ __ FIG. NO.-C-80-V TYPE- C CONSTANT LOAD MODEL R TOTAL TRAVEL - - - ACTUAL TRAVEL - - - ROD DIA. "J" - - - MACHINE THREADED ROD GRINNELL FIG. 140 OR EQUAL CLEVIS GRINNELL FIG. 299 OR EQUAL LOCK NUT -----~ -- ffi :1~ '------'-..... I \ I : I : f--t--1 L!-~ VIEW 8-8 VIEW A-A NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG N O . - - - - - - LOCATION DWG./ISO NO. _ _ _ _ __ ALTERNATE PIPE ATTACHMENT LINE N O . - - - - - - - - - - DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CONSTANT SPRING SUPPORT ASSEMBLY TYPE F, {BASE TYPE FROM STEEL) PNFS046 ocT 2004 1 0 1 SH-13t--PA_G_E__ _F__ _-----l I m I I I I I ~E _EL.==-=-= EXIST. TRUNNION OR SHOE SLIDING SURFACE P.O.S. EL. CONSTANT SPRING GRINNELL OR EQUAL SIZE----.,-FIG. NO. 81-H (UPTHRUST) TYPE F- _ _ __ CONSTANT LOAD - - - TOTAL TRAVEL ACTUAL TRAVEL - - - HYDRO TEST LOAD- _ _ __ EXISTING STEEL 1/4" NOTE: 1. BLANKS TO BE FILLIED BY USER. ASSEMBLY TAG N O · - - - - LOCATION DWG./ISO NO. _ _ __ LINE NO. _ _ _ _ _ _ _ __ DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CONSTANT SPRING SUPPORT TYPE F, SH-14 {BASE TYPE FROM STEEL WITH SLIDE PLATE) PNFS046 OCT 2004 PAGE 1 OF 1 I m I I 1 I I EXIST. TRUNNION OR SHOE P.O.S. EL CONSTANT SPRING GRINNELL OR EQUAL SIZE-.-:--:--:-::-=FIG. NO. 81-H (UPTHRUST) TYPE- F CONSTANT LOAD - - - TOTAL TRAVEL ACTUAL TRAVEL - - - HYDRO TEST LOAD- _ _ __ T.O.S. EL EXIST. BEAM NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG N O · - - - - LOCATION DWG./ISO NO. _ _ __ UNE NO. _ _ _ _ _ _ _ __ DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SPRING HANGER ASSEMBLY TYPE A, SH-15 {WITH WELDING LUGS FROM STEEL) PNFS046 OCT 2004 PAGE 1 OF 1 EXIST. STEEL S.O.S. EL. WELIDED BEAM ATTACHMENT GRINNELL FIG. 66 OR EQUAL GRINNELL SPRING WELDED EYE R.:..:O,D_ _ _ _ _--lll GRINNELL FIG. 278 OR EQUAL EL. _ _ _ ----~-+~ OR EQUAL SIZE TYPE- A FIG. NO. OPERAllNG LOAD COLID LOAD - - - MOVEMENT - - - HYDRO. TEST LOAD- _ _ __ MACHINE THREADED ROD GRINNELL FIG. 140 OR EQUAL GRINNELL FIG. 299 OR EQUAL ~ LOCKNUT ~ PINHO~- r-- I rA -..., T-- -- ----r= ~--r-~-~- ._=) -----, -M=t A I ~~~ I ~w VIEW B-B VIEW A-A NOTE: 1. BLANKS TO BE FILLED BY USER. ASSEMBLY TAG N O . - - - - - LOCAllON DWG./ISO NO. _ _ __ ALTERNATE PIPE LINE N O . - - - - - - - - ATTACHMENT DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PNFS046 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 SPRING HANGER ASSEMBLY TYPE D, SH-16 {WITH WELDING LUGS FROM STEEL) T.O.S. EL. EXIST. GRINNELL SPRING OR EQUAL SIZE- _ _ __ TYPE- D FIG. NO.- _ _ __ OPERATING LOAD - - - COUD LOAD-_ _ __ MOVEMENT-_ _ __ HYDRO. TEST LOAD MACHINE THREADED ROD GRINNELL FIG. 140 OR EQUAL GRINNELL FIG. 299 OR EQUAL rPIN HOLE ~--- LOCK NUT -----J---1--l ' --, :~=_r:::;_--, T=t '' ------fV!--_§J I I f---t--1 ~bW VIEW A-A NOTE: 1. BLANKS TO BE FILLED BY USER. ALTERNATE PIPE ASSEMBLY TAG N O . - - - - LOCATION DWG./ISO NO. _ _ __ UNE NO. _ _ _ _ _ _ __ ! --'-~ : I : A VIEW B-B ' -1 ,I -- ATTACHMENT DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PNFSOSO PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 14 TRUNNION SUPPORT, TR-A {HORIZONTAL SUPPORT ON HORIZONTAL PIPE) I ' ~' I ' ~------3-, i ' ~ I' PLAN ELEV. OF PIPE & lRUNNION ARE ALWAYS THE SAME \ --·--------t----- L ELEV. NOTE: 1. FOR lRUNNION DETAILS SEE PAGE 12 OF 14 2.1RUNNION CALL OUT AS PER PNFS0500 PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION SUPPORT, TR-8 (VERTICAL SUPPORT ON HORIZONTAL PIPE) ,-----I~L1I 4. WEEP-----. HOLE TOP OF STEEL OR CONCRETE ELEV. FOR BASE PLATE DIMENSIONS & DRILLING. SEE TR-2 (PAGE 13 OF 14) NOTE: 1. FOR TRUNNION DETAILS SEE PAGE 12 OF 14 2. TRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFSOSO OCT 2004 PAGE 2 OF 14 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION SUPPORT, TR-C 1/4" I'IEEP-----.. HOLE ELEV. FOR BASE PLATE DIMENSIONS & DRIWNG, SEE TR-2 (ON PAGE 13 OF 14) NOTE: 1. FOR TRUNNION DETAILS SEE PAGE 12 OF 14 2. TRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFSOSO OCT 2004 PAGE 3 OF 14 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION SUPPORT, TR-D {HORIZONTAL SUPPORT ON VERTICAL ELL) PNFSOSO OCT 2004 PAGE 4 OF 14 i I' ' 1' L ELEV. t PLAN NOTE: 1. FOR TRUNNION DETAILS SEE PAGE 12 OF 14 3. TRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. OF PIPE AND TRUNNION ARE ALWAYS THE SAME PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION SUPPORT, TR-E (HORIZONTAL SUPPORT ON VERTICAL PIPE) PNFSOSO OCT 2004 PAGE 5 OF 14 L 1 ' I ' I I' ' ~--1 ' i I' '' -{~------1--L~~V~EFINED ON ISO.) '' I l_ __ ~ ' I ELEV. * ANGLE IN DEGREES AS SHOWN ON ISO. PLAN NOTE: 1. FOR TRUNNION DETAILS SEE PAGE 12 OF 14 2. TRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFSOSO PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION SUPPORT, TR-F {HORIZONTAL SUPPORT ON VERTICAL ELL) OCT 2004 PAGE 6 OF 14 BOTTOM OF lRUNNION SAME AS PIPE UNLESS OlHERWISE NOTED ON ISO. L ELEV. -~::r---:-~:¥-------3-!.PIPE L ___L ___ _ I' PLAN NOTE: 1. FOR lRUNNION DETAILS SEE PAGE 12 OF 14 2. lRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. & lRUNNION PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION SUPPORT, TR-G {BOLTED SUPPORT ON VERTICAL PIPE) PNFSOSO OCT 2004 PAGE 7 OF 14 DEGREES AS SHOWN ON ISO. PLAN L I' 1/4" I'IEEP----, HOLE ~-- : i )-----------~~ I , I : I i , l:~ __ ' TOP OF STEEL OR CONC. I ELEV. FOR BASE PLATE DIMENSIONS & DRILLING, SEE TR-2 ON PAGE 13 OF 14 NOTE: 1. FOR TRUNNION DETAILS SEE PAGE 12 OF 14 2. TRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION SUPPORT, TR-H (BOLTED SUPPORT ON VERTICAL ELL) PNFSOSO OCT 2004 PAGE 8 OF 14 FOR BASE PLATE DIMENSIONS & DRILLING, SEE TR-2 ON PAGE 13 OF 14 PLAN L !&_ ELEV. SAME AS PIPE UNLESS OlHERWISE NOTED ON ISO. 1/4" WIEEP HOLE -~• TOP OF STEEL OR CONC. ELEV. NOTE: 1. FOR TRUNNION DETAILS SEE PAGE 12 OF 14 2. TRUNNION CAUL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N--'/_I_N_sT_A_L_LA_TI_o_N_D_ET_A_I_Ls_ _--l TRUNNION SUPPORT, TR-J ADJUSTABLE --~- __,___- ELEV. NOTE: 1. FOR TRUNNION DETAILS SEE PAGE 12 OF 14 2. TRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFSOSO ocT 2004 PAGE 9 OF 14 PNFSOSO PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION SUPPORT, TR-K (HORIZONTAL SUPPORT ON HORIZONTAL ELL) --~-- OCT 2004 PAGE 10 OF 14 t_ELEV. {AS DEFINED ON ISO) ' i ' ~ ' I' L ELEV. NOTE: 1. FOR TRUNNION DETAILS SEE PAGE 12 OF 14 2. TRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION SUPPORT, TR-M {VERTICAL SUPT. ON VERTICAL ELL OR HORIZONTAL PIPE) 1/4" VENT HOLE------.. --~-, I , ~ I' ELEVATION FOR PLATE DIMENSIONS AND DRILLING SEE TR-2 PAGE 13 OF 14~ E;:::+::;:J I I' ----- J I ----___( ______ : ------~-- ~-------1--------~J ' I NOTE: ELEVATION 1. FOR TRUNNION DETAILS SEE PAGE 12 OF 14 2. TRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFSOSO OCT 2004 PAGE 11 OF 14 PNFSOSO ocT PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TYPICAL TRUNNION ATTACHMENT DETAIL, TR-1 2004 12 14 t--PA_G_E__°F__ _ _---l ll I' zl' Q, ll ~I ::::>, ....I!' I c::i c::i d d "" ;;: "" D.. D.. ;;: PIPE WALL SHALL NOT BE BURNED THROUGH PIPE WALL SHALL NOT BE BURNED THROUGH OR CUT. OR CUT. ATTACHMENT WITHOUT ATTACHMENT WITH REINFORCING PAD REINFORCING PAD 1I . STIFF. ~---tt--(NOTE (MIN.) II BAR 1) I ~-:f SUPT. NOTE: 1. STIFFENING BARS 1 1/2"X1 /2" SHALL BE ALUMINUM FOR ALUMINUM TRUNNIONS, AND CARBON STEEL FOR CARBON STEEL TRUNNIONS AND ALL OTHER MATERIALS. SUFFICIENT SHIMS OR WEDGES ARE TO BE PROVIDED BY THE FIELD TO UNIFORMLY DISTRIBUTE THE TRUNNION LOAD ON THE SUPPORT UNLESS OTHER~SE NOTED. 2. TRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVIEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRUNNION ATTACHMENT, BASE PLATE DETAILS, TR-2 lRUNNION SIZE BASE PL SIZE 1 1/2" ,2",3" --- 8 X 8 X 3/8 4 .. ---------- 8 X 8 X 1/2 6"---------- 10 X 10 X 3/4 a" ---------- 12 X 12 X 3/4 1o· ---------- 12 X 12 X 1 12"- - - - - - - - - - 14 X 14 X 1 14"---------- 15 X 15 X 1 16"---------- 17 X 17 X 1 1a·---------- 19 X 19 X 1 20" - - - - - - - - - - 21X21X1 * 24"---------- 25X25X1 SEE ISO FOR TRUNNION SIZE * ALL LARGER lRUNNIONS-BASE PLATE SIZE = O.D.+ 1" X 1 1/4" lHICK 1 1/4" I ----."'-lRUNNION & BASE PL. r-! f ---+---$1 ' ' I I ' ' +- -I -t--+--t- 1/4" (3/4" DIA. ANCH. BOLTS, NUTS AND WASHERS NOT FURNISHED lHIS DRAWING) DRILLED BASE PLATE NOTE: 1. DO NOT DRILL BASE PLATE HOLES UNLESS CALLED FOR ON ISO. 2. lRUNNION CALL OUT AS PER PAGE 14 OF 14 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFSOSO OCT 2004 PAGE 13 OF 14 PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 TYPICAL TRUNNION DESIGNATIONS ON ISOMETRIC PIPING DRAWINGS, TR-3 PNFSOSO ocT 2004 PAGE 14 OF 14 CALL OUT IK TYPE (FROM PNFSOOOO) lRUNNI~ 10 - (80) - 24 - X I PIPE SIZE - - - - - - ' lRUNNION PIPE sa-IEDULE - - - - - - - - ' X = NO w- LENGTH~i:IR~d PAD WIDTH FR~ PN~8 PAGE 12 OF 14 ./~ r )/1• (80 0/ J/1 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. ---------' ----------' I =- =- PNFS0550 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ' ' OCT 2004 PAGE 1 OF 1 WELDING LUG, ATF-11 (FOR PIPING NPS 3 AND LARGER) 8 MIN. I I ttrc ----$---i/ ' I ' I t z ':!! ~ 3/16"V 1--- --- r--- --- 1'- - "' Q ELEVATION 5/8" PIN OR BOLT 3/4" 1 1/4" 2 1/2" 3" 1/4" 13/16" MAX. LOAD USER DEFINED USER DEFINED 8 3/4" 7/8" 1 1/4" 2 1/2" 3" 3/8" 15/16" USER DEFINED c 7/8" 1" 1 1/4" 2 1/2" D 1" TYPE ROD SIZE A E R 1 1/8" 1 1/2" 1 1/4" 1 3/8" 2" 8 MIN. D MIN. T H 3" 3/8" 1 1/8" USER DEFINED 3" 3" 1/2" 1 1/4" USER DEFINED 4" 4" 5/8" 1 1/2" USER DEFINED F 1 1/2" 1 5/8" 2 1/2" 5" 4 1/2" 3/4" 1 3/4" USER DEFINED G 1 3/4" 1 7/8" 2 1/2" 5" 4 1/2" 3/4" USER DEFINED 6" 4 1/2" 3/4" 2 3/8" USER DEFINED H 2" 2 1/4" 3" 2" I PIPE SUPPORT MARK NO. I ~ TYPE DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PNFS0551 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ') OCT 2004 PAGE 1 OF 1 WELDING CLIP, ATF-12 (FOR PIPING NPS 3 AND LARGER) EXISTING SlRUClURE r 1'--------"----S-----~f--'--.tT l.j<--!--,I.T ---TYP ~/16" ~/ v ---- -1 I < i ' I ' ---,--1--r--- i I i w : I : j ! B/2 l 'I B ELEVATION A 3/8" 2 7/8" 2" 1 1/4" 1/4" MAXIMUM RECOMMENDED (USER DEFINED) 7 /16" USER DEFINED B 1/2" 2 7;a· 2" 1 1/4" 1/4" 9/16" USER DEFINED TYPE ROD SIZE A B S T Z I PIPE SUPPORT MARK NO. I ~TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. =- =- PNFS0552 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ' ' OCT 2004 PAGE 1 OF 1 WELDING CLIP, ATF-13 (FOR PIPING NPS 3 AND LARGER) [_~'~"=~ --- ' TYP~ 3/16 ( ~.':'," ~-~ r H ~-.:- ~:; r--< ........ f~J rc rc 0 - / r-----------~ w "' .._ __ ---~ a:: I : j r-:J s rc r ! B/2 ~ 'I B l ' ELEVATION TYPE ROD SIZE BOLT SIZE R B D MIN. s T H MAXIMUM RECOMMENDED (USER DEFINED) A 3/B" 1/2 X 2 1/2 7/B" 2" 2" 1 1/4" 1/4" 9/16" USER DEFINED B 1/2" 5/8 X 2 1/2 7/8" 2" 2" 1 1/4" 1/4" 11/16" USER DEFINED I PIPE SUPPORT MARK NO. I ~ TYPE DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. =- =- PNFS0560 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ' ' OCT 2004 PAGE 1 OF 1 WELDING LUG, WL-1 H ,--I I/ I \ D f-----r---r-- ----I - --- I I TI E OR EE II II - il I PIPE SUPPORT MARK NO. I I I'<L-1- { ROD SIZE c I I ROD SIZE c D E EE G H FILLET WELD SIZE 3/8 & 1/2 3 1 2 4 1/2 3/8 11/16 3/16" 5/8 3 1 2 4 1/2 3/8 13/16 3/16" 3/4 4 1 1/4 2 1/4 5 1/2 15/16 3/16" 7/8 4 1 1/4 2 1/4 5 1/2 1 1/8 3/16" 1 4 1 1/2 2 1/2 6 5/8 1 1/4 1/4" 1 1/8 4 1 1/2 2 1/2 6 3/4 1 3/8 1/4" 1 1/4 4 2 2 3/4 6 1/2 3/4 1 1/2 1/4" 1 1/2 5 2 3 1/4 7 1/2 1 1 3/4 1/4" 1 3/4 5 2 1/2 3 1/4 7 1/2 1 2 1/4" 2 6 3 3 3/4 9 1 1/8 2 3/8 3/8" 2 1/4 8 3 1/4 4 1/4 10 1 1/4 2 5/8 3/8" 2 1/2 8 3 1/4 4 1/2 10 1 1/2 2 7/8 3/8" 2 3/4 10 4 5 11 1/2 1 1/2 3 1/8 3/8" DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. =- =- ' ' ! r-!L I ' ---E OCT 2004 PAGE 1 OF 1 WELDING LUG (ON ELBOW) WL-2 (FOR NPS 2-1/2 TO 30) r PNFS0561 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS RAD. - -- ~{SEE~ABLE 2) ' z,---- / - - u < I ' i<~' ____L____ ·" lfl"----'---- -It- ~ i I ' i 90' ELBOW /. u / D IAE!~E --i ~I ! '' ~·y ' INSULATION MAX. 4" ~-- --- '--11.,___.(_-, I IAE!~E: NO. OF NOTCHES ROD SIZE I """ 2 WELD SIZE 1/2" - 7 /8" 1 3/16" 1" - 1 1/2" 2 1/4" 1 3/4" - 3" 3 3/8" l DIMENSIONS ROD SIZE T D R H ELBOW SIZE (NPS) 2-1/2 3 3-1/2 4 5 6 8 10 12 14 16 18 20 22 24 26 28 30 c 7-5/16 7-7/16 7-1/2 7-1/2 7-1/2 7-9/16 7-7/16 7-5/16 7-1/8 6-3/8 6-1/8 5-13/16 6-3/4 7-1/2 7-1/4 7 7 7 MAX. LOAD N KIPS. 650'F MAX.) 21/4 1 2-1/2 1 2-3/4 1 3 1-1/4 8-1/2 "5-1/2 2-3/8 8-1/2 "5-1/2 2-5/8 9-3/4 "5-3/4 2-7/8 9-3/4 "5-3/4 "5-3/8 9-3/4 "5-3/4 H/8 12-9/16 1-11/16 1-5/8 11-9/16 1"5-1/2 1"5-1/2 11-1/2 1"5-1116 1"5-1116 15-1/8 11-5/8 1"5-1/16 1"5-1/16 14-11/16 16-13/16 16-13/16 11-13/16 11-13/16 11-13/11 11-13/16 1"5-1/16 1"5-1/16 14-1/2 16-1/16 16-1/16 17-7/8 11-7/8 11-7/8 11-7/8 11-7/8 1"5-1/16 1"5-1/16 14-3/8 15-3/4 15-3/4 17-5/16 12 12 12 1"5-3/16 1"5-3/16 14-7/16 15-3/4 15-3/4 17-1/8 12-1/4 12-1/4 1"5-7/16 1"5-7/16 14-11/16 15-15/16 15-15/16 17-5/16 12-5/16 1"5-1/2 1"5-1/2 14-11/16 15-15/16 15-15/16 17-1/4 1"5-1/2 1"5-1/2 14-11/16 15-15/16 15-15/16 17-3/16 17 18-3/8 14-3/4 15-7/8 17 17 18-1/8 18-1/8 19-3/8 17-1/4 18-3/8 18-3/8 19-1/2 18-1/4 18-1/4 19-3/8 19-5/8 19-5/8 20 17-7/8 17-5/16 17-1/8 17-5/16 17-1/4 17-3/16 18-3/8 19-3/8 19-1/2 19-3/8 19-5/8 20 18-15/16 18-1/8 17-7/8 18-1/16 17-15/16 17-7/8 19 20 20 20-1/8 2D-1/8 20 20 20-1/4 20-1/4 20-5/8 20-5/8 20 2D-1/8 20 20-1/4 20-5/8 1/2 1/4 "5-1/2 1-1/2 11/16 5/8 3/8 "5-1/2 1-1/2 13/16 3/4 3/8 "5-1/2 1-1/2 15/16 12-9/16 11-11/16 11-5/8 11-9/16 11-1/2 11-5/8 12-9/16 11-11/16 11-5/8 11-9/16 11-1/2 11-5/8 7/8 1/2 "5-1/2 1-1/2 1-1/8 1 1/2 5 2 1-1/4 1-1/8 5/8 5 2 1-3/8 1-1/4 5/8 6 2-1/2 2-1/2 1-1/2 3/4 7 3 1-3/4 1 3/4 1 7 3 2 2 1 A 12-9/16 11-11/16 11-5/8 11-9/16 11-1/2 11-5/8 USER DEFINED I PIPE SUPPORT MARK NO. I I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. 2 WL- -·{NPS PNFS060 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ocT 2004 1 0 2 CANTILEVER BRACKET FRQt,j ADJ. STEEL OR VESSEL, FPS-1t--PA_G_E__ _F__ _-----l (FOR PIPING UP TO NPS 2 1/2) A ~ 1/4" II II II II 2'-0" MAX. w r 1/4" ~p I I ·I· A 2'-0" MAX. lp I I I EL. y 1 ·~r i II II II II EXISTINGII COLUMN II L SEE TABLE II SEE TABLE I :•1: JA-1" , ' ' ' EXISTING! COLUMN II _li_-f--lL I ELEVATION I' ELEVATION FPS-1A FPS-1B A A 2'-0" MAX. m TV'T II II EL. y •·• I I , : I 1" --.rJ,'- r II II 2'-0" MAX. ~~~-----i======l=p=j----"'EL=.·....:Y_ EL. y I' ---+--------.-----' II II II II II II II II EXISTINGII COLUMN II II II II !I!' ' ' I SEE TABLE EXISTING! COLUMN ' II ! I ' I ~1/4" _li_-f--lL ELEVATION ELEVATION FPS-1C FPS-1E FPS-1D FPS-1F NOTES: 1.) FOR MAX. LOAD SEE TABLE ON PAGE 2. 2.) MAX. LOADS ARE FOR BRACKETS ONLY. CHECK VESSEL FOR LOCAL STRESSES (CHECK IF PAD IS REQUIRED). MAX. LOADS ARE FOR SUPPORT MEMBERS ONLY. CHECK EXISTING STIEEL FOR ADDITIONAL PIPING LOADS. 3.) 4.) SEE TABLE THE FOLLOI'I1NG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAI'I1NGS: EL. y DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CANTILEVER BRACKET FRQt,j ADJ. STEEL OR VESSEL, (FOR PIPING UP TO NPS 2 1/2) PNFS0600 ocT 2004 2 0 2 FPS-11--PA_G_E__ _F__ _---l r GUSSET t 1/2" X 5" X 5" (FOR INSULATED VESSELS ONLY). A I 2'-0" MAX. A 2·-o" A EXIST. tOR VESSEL PAD (FPS-26) EL. y EL. y ~ ~SEE TABLE . . ~--s-1---,-,.----....._ L_---'--2 ·~c- 1;4·1/ • 3 FACE OF CONCRETE OR VESSEL OUTSIDE FACE OF VESSEL ELEVATION ELEVATION FPS-1G FPS-1H FPS-1K A B c D E F G H K MAX. MAX. VERTICAL LOAD HORIZONTAL LOAD (USER DEFINED) (USER DEFINED) ANGLE SIZE TYPE 2 2 2 2 1/2 1/2 1/2 1/2 3 3 2 1/2 3 2 1/2 X X X X X X X X X 2 2 2 2 3 3 2 3 2 1/2 X 1/2 X 1/2 X 1/2 X X 3/8 X 3/8 1/2 X X 3/8 1/2 X 5/16 5/16 5/16 5/16 5/16 5/16 USER USER USER USER USER USER USER USER USER DEFINED DEFINED DEFINED DEFINED DEFINED DEFINED DEFINED DEFINED DEFINED USER USER USER USER USER USER USER USER USER I PIPE suPPORT MARK No.I IFPS-1~ TYPE DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. DEFINED DEFINED DEFINED DEFINED DEFINED DEFINED DEFINED DEFINED DEFINED PNFS0601 ocT PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS BRACED CANT. BRACKET Ft.l. ADJ. STL. OR VESSEL, (FOR PIPING UP TO NPS 2 1/2) A 2004 1 0 2 FPS-2t--PA_G_E__ _F__ _-----l A 4'-0" MAX. c 4'-0" MAX. c EL. y EL. y L3X3X3/B EXIST. COL. I /4" L2 1/2X2 1/2X5/16 I EXIST. COL. I I I I J41 ELEVATION ELEVATION FPS-2A FPS-2B NOTES: 1.) FOR MAX. LOAD SEE TABLE ON PAGE 2. 2.) MAX. LOADS ARE FOR BRACKETS ONLY. CHECK VESSEL FOR LOCAL STRESSES (CHECK IF PAD IS REQUIRED). 3.) MAX. LOADS ARE FOR SUPPORT MEMBERS ONLY. CHECK EXISTING STIEEL FOR ADDITIONAL PIPING LOADS. 4.) THE FOLLOI'<1NG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAI'<1NGS: EL. Y DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0601 ocT PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS 2004 2 0 2 FPS-2t--PA_G_E__ _F__ _-----l BRACED CANT. BRACKET Ft.l. ADJ. STL. OR VESSEL, (FOR PIPING UP TO NPS 2 1/2) A A c m c 4'-0" MAX. I EXIST. COL I I Iii II I I Ill i j!j : I Ill i I p 1'/P\: EL Y EL Y 1!1 ~~~ L3X3X3/8 ~ L2 1/2X2 1/2X5/16 1/4" I • "' j!' Ill I 111' I I Iii I I I II I I T -WU I 1" (TYP.) '~ "' 1'/P-i__j ' I I ' I PLATE 4X4X3/8 I I w ' ELEVATION FPS-2C TYPE ~ 1/4 OUTSIDE FACE OF VESSEL ELEVATION FPS-2D (FOR INSULATED VESSELS ONLY) ~tX VERT. LO~f MtX HORIZ. LO~~ SIZE USER DEFINED USER DEFINED A L3X3X3/8 USER DEFINED USER DEFINED 8 L3X3X3/8 USER DEFINED USER DEFINED c L3X3X3/8 USER DEFINED USER DEFINED D L3X3X3/8 USER DEFINED USER DEFINED I PIPE suPPORT MARK No.I IFPS-2~ TYPE DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PNFS060 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ocT DOUBLE COLUt.lN BRACKET FROI.l ADJACENT STEEL, FPS-3 (FOR PIPING UP TO NPS 2 1/2) A 5' 0" MAX. r ~l • r r 2004 1 0 1 t--PA_G_E__ _F__ _-----l EL. y ~ ID "' 0 I "' -_ ---~~OTE_?_) ---------------------~~OTE__2) ---~ --------------------------------------------EXISTING BEAM ============================================================================= ELEVATION NOTES: 1.) MAX. LOADS ARE FOR SUPPORT MEMBERS ONLY. CHECK EXISTING STEEL FOR ADDillONAL PIPING LOADS. 2.) USER TO DETERMINE IF GUSSETllNG OF EXISTING STEEL IS REQUIRED. 3.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING: EL. y I PIPE suPPORT MARK No.I IFPS-3-~A DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS060 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ocT DOUBLE COLUt,jN HANGER FRQt,j ADJACENT STEEL, FPS-4 (FOR PIPING UP TO NPS 2 1/2) 2004 1 0 1 t--PA_G_E__ _F__ _-----l -----------------------4 t -----------------------------EXISTING BEAM ==--===============--== (NOTE 2) (NOTE 2) ~ ID L3X3X3/8 "' 0 I "' r ' Jr A 5'-0" MAX. ELEVATION NOTES: 1.) MAX. LOADS ARE FOR SUPPORT MEMBERS ONLY. CHECK EXISTING STEEL FOR ADDillONAL PIPING LOADS. 2.) USER TO DETERMINE IF GUSSETllNG OF EXISTING STEEL IS REQUIRED. 3.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING. EL. y I PIPE suPPORT MARK No.I IFPS-4-.~A DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. EL. y Jr PNFS060 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ocT SINGLE COLUt.lN BRACKET FROI.l ADJACENT STEEL, FPS-5 (FOR PIPING UP TO NPS 2 1/2) 2004 1 0 1 t--PA_G_E__ _F__ _---l LJXJXJ/B A 5'-0" MAX. r ~l EL. y ' x < :::!; EXIST. COLUMN m 0 I ___ ----t co 1/4" 1!_~----------------'' ---(NoiEif----E~~ST1N-;; BE;~------~~ ===============================================~· K ELEVATION FPS-5A " 4-f-lL L3X3X3/B A 5'-0" MAX. ·1-lfIF==::::::!:::====! r '' EL. y ELEVATION FPS-58 NOTES: 1.) MAX. LOADS ARE FOR SUPPORT MEMBERS ONLY. CHECK EXISTING STEEL FOR ADDITIONAL PIPING LOADS. 2.) USER TO DETERMINE IF GUSSETTING OF EXISTING STEEL IS REQUIRED. 3.) THE FOLLOWlNG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWlNG: I PIPE suPPORT MARK No.I IFPS-5T~B TYPE A OR 8 EL. y DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SINGLE COLUMN HANGER FROM ADJACENT STEEL, FPS-6 (FOR PIPING UP TO NPS 2 1/2) PNFS060 ocT 2004 1 0 1 t--PA_G_E__ _F__ _---l I============================:::::::::JI ~ ~- ===_lli 9JUJ==== E:!STIN;= BE~~======J! x < :::E "'· I 0 ! io EL. y EXIST. COLUMN 1/4" p A 5'-0" MAX. ELEVATION FPS-6A EXISTING COLUMN~' ' ' . 1 =============================,~ (NOTE 2) EXISTING BEAM , ===--=======================]-- ' x < I' 1/4" :::E 1/4" "'· I 0 lp ~ ! I i1 I !I EL Y -i -+--1 1 1 - - , - - - - - - - - - - ! = = r-~ A 5' -0" MAX. r y I L3X3X3/8 ELEVATION FPS 6B NOTES: 1.) 2.) 3.) MAX. LOADS ARE FOR SUPPORT MEMBERS ONLY. CHECK EXISTING STEEL FOR ADDITIONAL PIPING LOADS. USER TO DETERMINE IF GUSSETllNG OF EXISTING STEEL IS REQUIRED. I PIPE suPPORT MARK No.I IFPS-6~ A'--B TYPE A OR B THE FOLLOI'I1NG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAI'I1NG: EL. y DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N--'/_I_N_sT_A_L_LA_TI_o_N_D_ET_A_I_Ls_ _--l T-SUPPORT FROM ADJACENT STEEL, FPS-7 A (FOR PIPING UP TO NPS 2 1/2) PNFS060 ocT 2004 1 1 PAGE OF A l 'i • I "' !P2 1'-0'" MAX. l 1'-o· 'i MAX. I !P1 l • ' I !P3 EL. y C4X5.4 1/4" ! I! WT3X7.5 1------"-= I 1/4" I ! I! I F============*==========1 ELEVATION FPS-7A 1/4" DETAIL OF ALTERNATE CONNECTION NOTES: 1.) P1, P2 AND DEFINED BY 2.) DIMENSIONS DEFINED BY P3 LOADS TO BE THE USER. A, B AND Y TO BE USER. I PIPE suPPORT MARK No.I IFPS-7A-,~A DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. EXIST. BEAM OR CHANNEL PNFS060 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS T -SUPPORT FROM ADJACENT STEEL, FPS-78 (FOR PIPING UP TO NPS 2 1/2) ----- v I x < I BEAM OR CHANNEL :I: 1/4"V ~ ::; -~EXIST. '' '' '' WT3X7.5 I m'b I + .1. Ill ~ •I•"V \ I Ill !P1 C4X5.4 !P2 / '' '' J I I L-+-J ~ 1'-o· 1'-0'" ~ EL. y MAX. MAX. A ELEVATION FPS-78 EXIST. BEAM OR CHANNEL DETAIL OF ALTERNATE CONNECTION NOTES: 1.) P1 AND P2 DEFINED BY 2.) DIMENSIONS DEFINED BY LOADS TO BE THE USER. A, B AND Y TO BE USER. I PIPE suPPORT MARK No.I I FPS-7B-T~ A DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. OCT 2004 PAGE 1 OF 1 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS PNFS060 ocT 2004 10 1 CANT. BRACKET FOR HORIZ. PIPING Ft,j. ADJ. STL., FPS-91--PA_G_E__ _F__ _---l (FOR PIPING UP TO NPS 2 1/2) 2'-o· L • ' MAX. EL. y I EXISllNG llE BEAM ~======~======~·~: --==~ 'I C4X5.4_/ 114" V v JiL -~EXISllNG BEAM ELEVATION FPS-9 A 2'-o'" MAX. -rJL-fllr - r 1 ! Il1,1l Ill II 1 ~·~ I EXISllNG COLUMN ~·~~ I ------------------ = ~~~-1-----,-+-. H C4X5.4 I ~ 1/4" I I -- 'i' ~ -;...:::0 II I I,L_+-- __ _ +-I ~·~r--1 -11~-:r::::------- I II I ~ I !i! I ~ - EXISllNG llE BEAM PLAN NOTE: 1.) THE FOLLOWING DIMENSIONS AND/OR INFORMAllON ARE SHOWN ON PIPING DRAWING: EL. y I PIPE suPPORT MARK No.I I FPS-9-X_ A DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0609 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SGL. "L" SUPT. OR HNGR. ADJ. ocT 2004 1 0 1 TO STL. OR VSL., FPS-10t--PA_G_E__ _F__ _-----l (FOR PIPING UP TO NPS 2 1/2) A 2' -3"(MAX.) c 2'-3"(MAX.) lp ,.., I I I / C4X5.4 vwY L H: 1': II II EXISTING BEAM ELY 1" 1" (TYP.) I I I L3X3X5/16 X < :::0 •0 1/4 ID I io L3 ,~v I I I p ELY = f' ~nr I = ~ II II ll---J~:::NG BEAM === = I ~-----' J ~ 1" 2'-3"(MAX.) (TYP.) ELEVATION A FPS - 10B 1/4V ELEVATION FPS - 10A IT IF LOCATION OF TIE TIE BEAMS EXCEED 1'-0", SUPPORTING BEAM '"'r___,_ _ _____.,.~ TO BE CHECKED FOR TORSIONAL MOMENTS i '\_. , I I =-=tr= ==,1=1 I, ~~ 1•1 ~~~ NOTES: 1. USE EITHER DIM. A OR DIM. C, BUT NOT SIMULTANEOUSLY. 2. DIMENSIONS A OR C, B, AND Y TO BE DEFINED BY USER. I PIPE suPPORT MARK No.I II I 11 I 11 I 11 I ---'-----=u.s ---r- ~EXISTING SECTION A-A IFPS-10,~ ~~AORB DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. BEAM PNFS0611 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SUPPORT FOR VERTICAL PIPING, FPS-12 (FOR PIPING UP TO NPS 2 1/2) (2) 1/2" DIA. BOLTS (LOCATE AT MIDSPAN) WllH WASHER AND HEX NUT. (HAND TIGHTEN AND TACK WELD NUT TO BOLT). CONNECT FREE TO SLIDE PLAN EXISTING STRUCTURE OR VESSEL I 1M :=:=:=:f:~=~ ' lp I ' ~ I ' ·s· t. 5/16" i ~J __IL___"A j •----j' (2) 9/16" DIA. HOLES IN t.'A' 5/16" I i (2) 9/16"X 2" SLOTTED HOLES IN t. '8' ELEVATION NOTES: DESIGN LOAD: 1.) MAX. LOADS ARE FOR ATTACHMENT ONLY. CHECK PIPE FOR LOCAL STRESSES. 2.) lHE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING: EL. y OCT 2004 PAGE 1 OF 1 MAX. LOAD P (USER DEFINED) = USER DEFINED I PIPE suPPORT MARK No.I I FPS-12-X_ A DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. =- =- ' ' INS. CL.L= r PNFS0612 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 CANTILEVER SUPPORT ADJACENT TO STEEL, FPS-13 (FOR PIPING UP TO NPS 2 1/2) ff- ~ 11 I I I 11 I\_ n I I ~ ' 4" II I I L3X3X3/8 2' -0" MAXIMUM I I 11 I II 1~ J ~1 l I ' IL EXISTING CHANNEL OR W BEAM II II ll 1" 2' -6" MINIMUM c A PLAN !p m ~ mI i !I! i EXISTING ~ ATIACHMENT I //'"V i 1\- -~~~··v EL. y I : i : I I ~ ELEVATION FPS-13 v.v\lt:~ t __JL, f DESIGN LOAD: VERTICAL LOAD: P (USER DEFINED} = USER DEFINED II 1 NOTE: 1.) ~ ~ THE FOLLOv.1NG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAv.1NG: EL. y II WF 1/4" ALTERNATE BEAM CONNECTION I PIPE SUPPORT MARK No.I IFPS-13-~~ ~c DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PNFS0614 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ocT CANTILEVER BRACKET FOR PIPE SUPPORTS, FPS-15 (FOR PIPING UP TO NPS 2 1/2) 2004 1 0 A c 3" i , 1 3' -0" MIN. ~ExisTING ~,......- sTIEEL ~ cHANNEL oR 1 BEAM ............._ l I • 1 w 3' -6" MAX. .. 11 EL. y ' r Ql -:.T7v-< (TYP.) >-c 114 ! lp 1 ' C4X5.4_/ ELEVATION FPS-15A DESIGN LOAD: ALLOWABLE LOAD P (USER DEFINED) = USER DEFINED NOTES: 1.) EXISTING SUPPORTING MEMBERS TO BE CHECKED FOR ADDITIONAL PIPING LOAD. 2.) IF OBSTIRUCTION BETWEEN EXISTING MEMBERS DOES NOT ALLOW THE USE OF THIS STANDARD CONNECTION, USE ALTIERNATIE CONNECTIONS AS SHOWN ON SHEET 2. 3.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING: EL. y I PIPE suPPORT MARK No.I IFPS-15,.~ ;: ~E DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. 2 I--PA_G_E__ _F__ _---l (LAST LETTIER ONLY) PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CANTILEVER BRACKET FOR PIPE SUPPORTS, FPS-15 (FOR PIPING UP TO NPS 2 1/2) EXISllNG STEEL 1/4" ~!I 'I II hi 1 1/4" ' HANGER L3X3X3/B (FIELD TRIM TO SUIT) ELEVATION EXISllNG STEEL FPS 15B 1/4" 1/4" i''\.__ HANGER L3X3X3/B (FIELD TRIM TO SUIT) ELEVATION FPS-15C ELEVATION FPS-15D ALTERNATE CONNECTIONS SEE NOTES AND DIMENSIONS ON SHEET 1 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS061 ocT 2004 2 0 2 I--PA_G_E__ _F__ _-----l PNFS061 ocT PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CANTILEVER BRACKET FOR PIPE SUPPORTS, FPS-16 (FOR PIPING UP TO NPS 2 1/2) 2004 1 0 2 I--PA_G_E__ _F__ _---l A 3" c w 3'-0" MIN. 3'-6" MAX. ~EXISTING ~ ' I ' I STIEEL ~ vnANNEL OR I BEAM ............._ I' lp EL. y W4X13 ELEVATION FPS-16A DESIGN LOAD: ALLOWABLE LOAD P (USER DEFINED) = USER DEFINED NOTES: 1.) EXISTING SUPPORTING MEMBERS TO BE CHECKED FOR ADDITIONAL PIPING LOAD. 2.) IF OBSTIRUCTION BETWEEN EXISTING MEMBERS DOES NOT ALLOW THE USE OF THIS STANDARD CONNECTION, USE ALTIERNATIE CONNECTIONS AS SHOWN ON SHEET 2. 3.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING: EL. y I PIPE suPPORT MARK No.I IFPS-16.,~ ;: .g,E (LAST LETTIER ONLY) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 CANTILEVER BRACKET FOR PIPE SUPPORTS, FPS-16 (FOR PIPING UP TO NPS 2 1/2) 1 PNFS061 ocT 2004 2 0 2 t--PA_G_E__ _F__ _-----l 1/4" ' HANGER W4X13 (FIELD TRIM T<l SUIT) ELEVATION FPS-168 I i lIll l lol I ======! I===='==I ELEVATION FPS-16C ELEVATION FPS-16D ALTERNATE CONNECTIONS SEE NOTES AND DIMENSIONS ON SHEET 1 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. 1/4 p EL. y PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SUPPLEMENTARY STEEL DETAIL, FPS-20 (FOR PIPING UP TO NPS 2 1/2) ~ /1/4"~ EL. y 3 SIDES (TYP.) I [ J q]~ [] FPS-20A & 208 (FOR MEMBER SIZES SEE TABLE) ~3SIDES /1/4"V:. '\.(TYP.) r EL.J; FPS-20C & 20D (FOR MEMBER SIZES SEE TABLE) MEMBER SIZE TYPE A B L3X3X3/8 L4X4X3/8 c C4X5.4 C6X8.2 D B MAX. LOAD LBS. (USER DEFINED) 2 1 /2" USER 2 1/2" USER 2 1/8" USER 2 1 /8" USER MAX. SPAN s·-o· a·-o· a·-o· a· o· DEFINED DEFINED DEFINED DEFINED NOTES: 1.) EXISllNG SUPPORllNG MEMBERS TO BE CHECKED FOR ADDillONAL PIPING LOAD. 2.) USE IF OBSllRUCllON BETWEEN EXISllNG BEAMS DOES NOT ALLOW THE USE OF STANDARD CONNECllONS. 2.) THE FOLLOI'I1NG DIMENSIONS AND/OR INFORMAllON ARE SHOWN ON PIPING DRA1'11NG: EL. y I PIPE suPPORT MARK No.I IFPS-20,@ A B TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0619 OCT 2004 PAGE 1 OF 1 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SUPPLEMENTARY STEEL DETAIL, FPS-21 (FOR PIPING UP TO NPS 2 1/2) ~ EXISTING" :XISTING ':: j~ ..J. /~•·v . / ., • !I ! I FOR MEMBER S I Z E / 1"' ~ ~~ SEE TABLE. ALTERNATE CONNECTIONS 1:9/-:-4"'""V...,.- FPS-21A, B, C & D MEMBER SIZE MAX. LOAD LBS. (USER DEFINED) MAX. SPAN B L3X3X3/8 L4X4X3/8 USER DEFINED USER DEFINED c C4X5.4 D C6X8.2 USER DEFINED USER DEFINED s·-o· a·-o· a·-o· a·-o· TYPE A NOTES: 1.) EXISTING SUPPORTING MEMBERS TO BE CHECKED FOR ADDITIONAL PIPING LOAD. 2.) USE IF OBSTIRUCTION BETWEEN EXISTING BEAMS DOES NOT ALLOW THE USE OF STANDARD CONNECTIONS. 3.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING: EL. y I PIPE suPPORT MARK No.I IFPS-21@ A C TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0620 OCT 2004 PAGE 1 OF 1 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CINCH PLATE, FPS-26 (FOR PIPING UP TO NPS 2 1/2) PNFS062 OCT 2004 PAGE 1 OF 1 ELEVATION FPS-26A ~ ~ ~ • ~ - c z ::::> 0 "'--'< --' < (4) 9/16" e HOLES AND 4 1/2"X 5 1/2" LG. CINCH ANCHOR jOLTS (BY FIELD) ' EL Y "'"' << ~ CONCRETE SECTION 'A-A' ELEVATION FPS-26B NOTES: 1.) SPECIFY LENGTH OF BOLT ON ISO, IF OTHER THAN 5 1/2". 2.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING. I PIPE suPPORT MARK No.I IFPS-26,~ A TYPE (LAST LETTER ONLY) EL. y DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PNFS062 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 20034 PAGE 1 OF 1 'T' POST, FPS-28 (FOR PIPING UP TO NPS 2 1/2) A ELEVATION Y x < ~ "' 'b I ;,. WT3X7.5 1" GROUT IF REQUIRED ELEVATION ALllERNA1lE CONNECTIONS ADJACENT TO COLUMN 4 - 9/16" DIA. HOLES IN PLAllE & 1/2" X 5 1/2" LG. (OR c"") CINCH BOLTS (BY FIELD) ' ~ :--- ., •"' I ~ -"' - ~ ...., 1/4" v 1 1/2" " P1 = USER DEFINED P2 = USER DEFINED P3 = USER DEFINED NOTIES: l I 5" 1 1/2" DESIGN LOADS: (USER DEFINED) :mm1' - PL 8"X 3/8"X 8" -- " SECTION A-A 1. THE FOLLOI'I1NG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING: EL. y I PIPE suPPORT MARK No.I I FPS-28- - - ~ '\_}G; C (FOR CINCH BOLT DIA. ONLY) DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PNFS062 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 'T' POST, FPS-29 (FOR PIPING UP TO NPS 2 1/2) A 1'-3'" L 1'-3" MAX. I' MAX. ELEVATION Y ~ !P I ~ x '~ -t' 1/4"V < L3X3X3/8 •"' 0 "' I ;,. :iii • "' ·: ·.: .:l ' I : kf·' .. ..:.·.:I : L~·· ~·· "~~/~~~ ·····l'l'f·"· > I -;... ~ . • •I I : .-:;::·u I. :~ ~-~..-·;:. ... ~, . ''"· .= ' I TOP OF GRADE / TOP OF CONCRETE PIER • 'io FILL WllH CONCRETE ~ f z ·~w~ ~.r/ I :1·:.:· : r----DEPlH TO FROST LINE OR VIRGIN SOIL .;:/.\;ts .·.?:::; ELEVATION ALTERNATE CONNECTIONS ADJACENT TO COLUMN 4 9'" 4 9'" I, 1 (TYP.) ~I (TYP ) 1 18" SQ. OR 2' -0" ROUND ~ ' r---!~ =11= i I L---- NOTES: ~ •,.., _____J . • ~ '~ L 1 'I 1.) lHE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING: EL. Y .. SECTION A-A 2.) DO NOT USE FOR GUIDE OR ANCHORS. DESIGN LOAD: VERT. LOAD P (USER DEFINED) = USER DEFINED P-IP_E_S-UP_P_O_R_T_M_A_R_K_N---,0.1 'I I FPS-29T--.] '--::-s DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0629 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SUPPORT FROM GRADE OR STEEL, FPS-30 (FOR PIPING UP TO NPS 2 1/2) OCT 2004 PAGE 1 OF 2 LONG RADIUS ELBOW UNLESS NOTED .i.f'IPE____ _ L2 1/2X 2 1/2X 5/1 {TYP.) < ~ 1" GROUT IF REQD. {TYP.) BASE PLATE {TYP.) SEE PAGE 2 FOR DETAILS SECTION 'A-A' ELEVATION FPS-30A ru+~-- - - ---~ --- -- ~ 1" GROUT IF REQD. {TYP.) 1" GROUT IF REQD. (TYP.) ELEVATION SECTION '8-8' ELEVATION FPS-30B FPS-30C I PIPE suPPORT MARK No.I IFPS-30T~ ; NPS TYPE {LAST LETTER ONLY) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. SECTION 'C-C' PNFS0629 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SUPPORT FROM GRADE OR STEEL, FPS-30 (FOR PIPING UP TO NPS 2 1/2) CUT TO FIT L2 1/2X 2 1/2X 5 / 1 6 - - ...1:c::~~ TOP OF GRADE PIER OR STEEL (TYP.) ELEVATION FPS-30D PS NUMBER FPS-30A/B/C/D M(~X. LOAD 'I~~Bri) USER DEFI ED PIPE SIZE LIMITATION p UP TO 2 1/2" DIA. t H USER DEFINED USER DEFINED PLATE A 4"X 4"X 1/2" ' I • "' ' -----t--i -.... ~'---- • "' 2" ! -~ 2" 14"V 1I BASE PLATE DETAIL DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. OCT 2004 PAGE 2 OF 2 PNFS0639 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 ADJUSTABLE SUPPORT FROM GRADE OR STEEL, FPS-40 (FOR PIPING UP TO NPS 2 1/2) t PIPE ' -f-1-:=f~~/ I ALTERNATE t ARRANGEMENT L = FOR LOI'<ER CENTERLINE T = FOR SUPPORT AT TOP OF ELBOW t 2" X 6" X (FIELD 1" DIA. ROD TOP OF OR STEEL • 1 GROUT (IF REQUIRED) BILL OF MATERIAL ITEM QUA. LIN. FT. AS REQUIRED 2" DIA. SCH. 40 PIPE AS REQUIRED 1" DIA. ROD HEX NUTS FOR ROD 2 AS REQUIRED AS REQUIRED t t 1/4" THICK 3/B" THICK MAX. LOAD (USER DEFINED) = USER DEFINED I PIPE suPPORT MARK No.I I FPS-40-'T-~- I '\O...K;K:"L" OR "T" (ONLY FOR ALTERNATE) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ADJUSTABLE SUPPORT FROM GRADE OR STEEL, (FOR PIPING UP TO NPS 2 1/2) PNFS064 ocT 2004 1 0 1 FPS-411--PA_G_E__ _F__ _---l 1" t 1" --}-1/4" " DIA. ROD fi!.2"X 2"X 3/8" 2" DIA. SCH. 40 PIPE - - - l i TOP OF PAVING BILL OF MATERIAL QUA. LIN. FT. ITEM AS REQUIRED STD. WT. PIPE 2" DIA. AS REQUIRED 1" DIA. ROD AS REQUIRED fl!. 2 3/8" THICK HEX NUTS FOR ROD AS REQUIRED fl!. 1/4" THICK MAX. LOAD (USER DEFINED) = USER DEFINED P-IP_E_S_U_P_P-OR-T-MA_R_K-N0--,.1 'I I FPS-41- - - ~ .,-'-~'--;; "S" (FOR ALT. CONN. TO STRAIGHT PIPE} DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. II!. PNFS0649 ocT PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CANTILEVER BRACKET FROM ADJACENT PIPING, FPS-50 (FOR PIPING UP TO NPS 2 1/2) 2004 1 0 1 t--PA_G_E__ _F__ _-----l / INSULATED PIPE \ \ EL. y ,, I " ' - - L3X3X3/8 C6X8.2 B 2'-0" MAX. A (2'-0" MAX.) ELEVATION FPS-50A 6" DIA. MIN. ~ / /L3X3X5/16 _j_--~hSW"HA--~"-----' \ FIELD CUT TO SUIT \ I ~! A (2'-0" MAX.) ELEVATION NOTES: FPS-50B ALTERNATE CONNECTION 1. SUPPORT UP TO 2' -0" MAX.; PIPE TO BE SUPPORTED SHOULD NOT EXCEED ONE-FOURTH THE DIAMETER OF THE SUPPORTING PIPE. 2. ELEVATION Y TO BE SHOWN ON PIPING DRAWING. I PIPE suPPORT MARK No.I IFPS-50~~ A ~E (LAST LETTER DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. ONLY) EL. y PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N--'/_I_N_sT_A_L_LA_TI_o_N_D_ET_A_I_Ls_ _--l SUPPORT FOR DRAIN PIPE, FPS-42 (FOR PIPING UP TO NPS 2 1/2) CUT TO SUIT IN FIELD 3/16" t 4"X 4"X <t I ' I m ' I -1'----~11 I.I GRADE FPS-42 I PIPE suPPORT MARK No.I I FPS-421 DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. ocT 2004 PAGE DRAIN ELEVATION PNFS0641 1 OF 1 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CANTILEVER BRACKET FROM ADJACENT PIPING, FPS-51 (FOR PIPING UP TO NPS 2 1/2) PNFS065 ocT 2004 1 0 1 t--PA_G_E__ _F__ _-----l 1/4" FOR SHOE SEE PNFS0401 OR PNFS0402 (CALL SHOE OUT SEPARATELY) ELEVATION (SUPPORTING PIPE FROM 6" TO 12" DIA.) NOTES: 1.) SUPPORT UP TO 2 FT. MAX.; PIPE TO BE SUPPORTED SHOULD NOT EXCEED ONE-FOURTH THE DIAMETER OF THE SUPPORTING PIPE. 2.) THE FOLLOWING DIMENSION AND/OR INFORMATION ARE SHOWN ON PIPING DRAWINGS: EL. Y. I PIPE suPPORT MARK No.I I FPS-51-X_ A DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CANTILEVER BRACKET FROM ADJACENT PIPING, FPS-52 (FOR PIPING UP TO NPS 2 1/2) PNFS0651 ocT 2004 1 0 1 t--PA_G_E__ _F__ _-----l 8 {2' -0" MAX.) {2'-0" MAX.) FOR SHOE SEE PNFS0401 OR PNFS0402 (CALL SHOE OUT SEPARATELY) ELEVATION {SUPPORTING PIPE FROM 6" TO 12" DIA.) NOTES: 1.) SUPPORT UP TO 2 FT. MAX.; PIPE TO BE SUPPORTED SHOULD NOT EXCEED ONE-FOURTH THE DIAMETER OF THE SUPPORTING PIPE. 2.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWINGS: EL. Y. I PIPE suPPORT MARK No.I I FPS-52--\L_ B DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS066 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS BRACED CANTILEVER BRACKET FROt.i ADJACENT TOWER, FPS-64 (FOR PIPING UP TO NPS 2 1/2) A II!. ~;f-7w-V_4" J\. """ "" 3"X3"X 3/8" _ / ~ ii!.6"X6"X1/2" (TYP. 2) / INSULATION PLAN EL. y 3" '---OUTSIDE RADIUS OF VESSEL 1/4" I i L2 1/2X2 1/2X5/16 ' NOTIE: 1------tf- ! 1.) GUSSETI CONNECTIONS FOR UNINSULATIED VESSELS MAY BE OMITIED. 2.) MAX. LOADS ARE FOR BRACKETS ONLY. CHECK VESSELS FOR LOCAL STRESSES. (CHECK TO SEE IF PAD IS REQUIRED). I ' 1-------J~I ELEVATION 3.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING: EL. y I PIPE suPPORT MARK No.I IFPS-64-~R DESIGN LOAD: VERT. LOAD P (USER DEFINED) = USER DEFINED HOR. LOAD H (USER DEFINED) = USER DEFINED A DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I' OCT 2004 PAGE 1 OF 1 PNFS066 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ocT BRACKET FOR VERTICAL PIPING FROM ADJACENT VESSEL, FPS-65 (FOR PIPING UP TO NPS 2 1/2) (2) 1/2" BOLTS 'MlH WASHERS & NUTS. HAND TIGHTEN & TACK 'MELD TO BOLTS. I 2004 1 0 2 t--PA_G_E__ _F__ _----l H I I ~··\'r--L-----n EXIST. PAD- ---}----------~ I :1r-----------~ I I I L4X3X3/B \1 -1'-------"-------.1'-___t.----i! OUTSIDE-----, RADIUS (R) ~ 1/2 PIPE O.D. INS. lHK. + 1/2" --+ PLAN ~ ~p 3/B" It (SEE DETAIL SHT. 2) I 6" EL. y ,..' _,_I ' 111 --t ___ I ! __ t------ --I I' I VESSEL OR STRUCTURE L4X3X3/B 1 4 / " L2X2X5/16 _L ___ 1 1/4" 1 3/4" 1" I I w_j I ELEVATION NOTES: 1.) lHE FOLLO'MNG DIMENSIONS AND/OR FPS-65A INFORMATION ARE SHOWN ON PIPING DRA'MNG: EL. Y. 2.) FOR ALTERNATE CONNECTIONS DETAILS, SEE PAGE 2. I PIPE suPPORT MARK No.I IFPS-65~~ A'-NPS TYPE (LAST LETTER ONLY) DESIGN LOAD: VERTICAL LOAD: P (USER DEFINED) = USER DEFINED HORIZONTAL LOAD: H (USER DEFINED) = USER DEFINED DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. 4" PNFS066 PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N--'/_I_N_sT_A_L_LA_TI_o_N_D_ET_A_I_Ls_ _--l BRACKET FOR VERTICAL PIPING FROM ADJACENT VESSEL, FPS-65 (FOR PIPING UP TO NPS 2 1/2) c INS. lHK. + 2 1/2" 2" ~ II I ocT 2004 2 0 2 t--PA_G_E__ _F__ _----l ~ I (TYP.) I EXIST. PAD I ~ ~ ' .---• z "' .... z"' I II -Ef3 I 3" ~ s• I w~ I PIPE PLATE DETAIL FPS-65A 3" • ~ • "' It VESSEL PLATE DETAIL (FOR INSULATED VESSELS ONLY) FPS-658 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS BRACED CANTIL£VER BRCKT. FOR HORZ. PIPING FROM ADJ. VESSEL, FPS-80 PNFS0679 ocT 2004 1 0 1 I--PA_G_E__ _F__ _--l (FOR PIPING UP TO NPS 2 1/2) A c 2'-0" MAX. W. P. EL. y L2 1/2X2 1/2X5/16 1/4" HORIZONTAL VESSEL DESIGN LOAD: PS-80A VERT. LOAD, P (USER DEFINED) = - - - - PS-808 VERT. LOAD, P (USER DEFINED) FIELD CUT TO SUIT (TYP. 2) HORIZ. LOAD (USER DEFINED) = - - - HORIZ. LOAD (USER DEFINED) =---=---- A 4'-0" MAX. ELEVATION FPS-80A HORIZONTAL VESSEL FIELD CUT TO SUIT 1" (TYP.) NOTES: 1. 1/4" I PIPE suPPORT MARK MAX. LOADS ARE FOR BRACKETS ONLY. CHECK VESSELS FOR LOCAL STRESSES. (CHECK IF PAD REQ'D.). 2. THE FOLLOWING DIMENSIONS AND/OR INFORM AliON ARE SHOWN ON PIPING DRAI'I1NG: No.I EL. y IFPS-80.~ ; B OR C TYPE (LAST LETliER ONLY) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS070 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 2 SHORT LENGTH ROD HANGER FROM ADJACENT STEEL, FPH-1 (FOR PIPING UP TO NPS 2 1/2) r EXIST. STEEL (TYP.) c====5'ri"=nr===·=d - - , f - - - - b=·==='n''"iiF=====J EL. y ATTACHMENT OR 3 BOLT CLAMP (SPECIFY MATERIAL) SEE PAGE 2 CLEVIS CLAMP (SEE PAGE 2) INSULATION FPH-1A-A FPH-1A-C (B FOR 2 BOLT CLAMP) ROD DIA. x 3 ATTACHMENT <( <( ROD (HF- ) OR (RF- ) FPH-1 B FPH-1C c============J " E~-,·....tY_TYP-~-3-/-,.;-~~~-'J OR (RF- ) FPH-1 D NOTE: 1.) SUFFIXES A, 8, C & D APPLY TO INSULATED UNES ONLY. 2.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWING: A. ROD CLAMP I PIPE suPPORT EL. y MARK No.I ~-~ ·~ C~~~p TYPE (LAST LETTER O N L Y ) , TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0700 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS SHORT LENGTH ROD HANGER FROM ADJACENT OCT 2004 PAGE 2 OF 2 FPH-1 STEE~ (FOR PIPING UP TO NPS 2 1/2) MAX. INCHES PIPE SIZE ~~~DI-A~.-c~~~E-.~H-.~L--.-~J-.--~s--.---s~1--~ 1/2 600 3/8 3/4 600 3/8 1/2 1 600 3/8 5/8 1 1/4 600 3/8 7/8 1 3/4 2 9/16 3 7/16 1 1/2 600 3/8 1 1/16 2 1/8 2 600 3/8 2-1/2 1100 1/2 7/16 7/8 1 11/16 2 1/8 1/4 1 X 1/8 1 X 1/8 2 7/16 1/4 1 X 1/8 1 X 1/8 1 1/4 2 1/8 2 13/16 1/4 1 X 1/8 1 X 1/8 1/4 1 X 1/8 1 X 1/8 1/4 1 X 1/8 1 X 1/8 1/4 1 X 1/8 1 X 1/8 1 1 7/8 3 4 1 5/8 2 15/16 3 11/16 4 7/8 2 3 13/16 4 11/16 6 1/8 3/8 1 1/4 X 3/16 1 1/4 X 3/16 CLEVIS CLAMP (TYPE A) MAX. LOAD LBS. INCHES PIPE 1--:-:M-:-:ATL~.-=-c.-=-s.-,A~3=87::-_-:G:=R~.2-::-2t----,---,---,----,----j SIZE B J T w 650'F 750'F 1OOO'F 1050'F F 1/2 500 445 315 230 1/2 5/16 1/8 3/4 500 445 315 230 1 1/8 1/2 5/16 1/8 500 445 315 230 1 3/8 1/2 5/16 1/8 1 1/4 500 445 315 230 1 7/16 1/2 5/16 1/8 1 1/2 BOO 715 530 350 5/16 1/8 1040 930 660 480 2 1/8 1/2 1/2 1/4 2 1/2 1040 930 660 480 2 5/8 5/8 1/2 1/4 2 1 5/8 1/2 2---BOLT CLAMP (TYPE B) MAX. LOAD LBS. I PIPE SIZE w - ~I --+--t-+ .-·- T~' LL -I- ~ ~ INCHES MATL. C.S. A387-GR.22 ~~~~100~ 1 ~~ F E B J T 1/2 950 850 600 440 15/16 2 7/16 5/16 3/8 3/16 3/4 950 850 600 440 15/16 2 7/16 5/8 3/8 3/16 1 950 850 600 440 1 1/6 2 9/16 5/8 3/8 3/16 1 1/4 950 850 600 440 1 1/4 2 11/16 5/8 3/8 3/16 1 1/2 1545 w 1380 1000 745 1 13/16 41/8 1 1/16 5/8 1/4 1 1/4 1545 1380 1000 745 2 1/8 5 1/8 1 1/16 5/8 1/4 1 1/4 2 1/2 1545 1380 1000 745 1/4 1 1/4 2 2 5/16 5 3/8 1 1/16 5/8 3---BOLT CLAMP (TYPE C) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0701 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 2 LONG LENGTH ROD HANGER FROM ADJACENT STEEL, FPH-2 (FOR PIPING UP TO NPS 2 1/2) ROD DIA. X 3 AlF-8 EL. y < ROD 1 (RF. (R.H. THO.) JAM NUT FPH-28 . I t-- . ) ---' f== •0 ROD 2 {RF. } _, t------r-------; L,. I .> {6" GAP) "' < EL. y TURNBUCKLE i;l ALTERNATE CONNECTION FOR FPH-2A ) ROD 2 (HF. ) {L.H. THO.} SAME DIA. AS ROD 1 I -;... ___ 7 _=:j < ATTACHMENT {AlF-3} RF. SEE PAGE 2 {SPECIFY MATL.) ) INSULATION FPH-2C ALTERNATE CONNECTION FOR FPH-2A L c.:---:~ ~~ 1 c.:~· ___ _J < ATTACHMENT {AlF 4} (RF. }. I -=E=L.'--YT---1! ~=~£<':=J-.....!2ATT~AC~H~M~E!!NT!_.!!(A~1F!.=.;7C~} I ~I' :It--,-rrr...J T I CLEVIS (CLF ) < FPH-2D FPH-2A L ~ c-------- L U,......_ -'E=L::.... . ..:,Y,--_ _ X ~--.s, I ALTERNATE CONNECTION FOR FPH-2A ROD 1 (RF- ) FPH-2E NOTE: ALTERNATE CONNECTION FOR FPH-2A 1.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWINGS: EL. Y AND X DIMENSION .=7 _ I PIPE SUPPORT MARK NO.I . . ~ TYPE (LAST LETTER ONLY) ~ "~ C~~p TYPE DIMENSIONS ARE GIVIEN IN FEET AND/OR INCHES. PNFS0701 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ') OCT 2004 PAGE 2 OF 2 LONG LENGTH ROD HANGER FROM ADJACENT STEEL, FPH-2 (FOR PIPING UP TO NPS 2 1/2) MAX. INCHES PIPE SIZE ~~~DI-A~.-c~~~E-.~H-.~L--.-~J-.--~s--.---s~1--~ 1/2 600 3/8 3/4 600 3/8 1/2 1 600 3/8 5/8 1 1/4 600 3/8 7/8 1 3/4 2 9/16 3 7/16 1 1/2 600 3/8 1 1/16 2 1/8 2 600 3/8 2-1/2 1100 1/2 7/16 7/8 1 11/16 2 1/8 1/4 1 X 1/8 1 X 1/8 1 7/8 1/4 1 X 1/8 1 X 1/8 1 1/4 2 1/8 2 13/16 1/4 1 X 1/8 1 X 1/8 1/4 1 X 1/8 1 X 1/8 1/4 1 X 1/8 1 X 1/8 1/4 1 X 1/8 1 X 1/8 1 2 7/16 3 4 1 5/8 2 15/16 3 11/16 4 7/8 2 3 13/16 4 11/16 6 1/8 3/8 1 1/4 X 3/16 1 1/4 X 3/16 CLEVIS CLAMP (TYPE A) MAX. LOAD LBS. INCHES PIPE 1--:-:M-:-:ATL~.-=-c.-=-s.-rA:-::3-:-87::-_-:G:=R~.2-:-2t----,---,---,----,----j ~~ F B J T w 650'F 750'F 1OOO'F 1050'F 1/2 500 445 315 230 1 1/2 5/16 1/8 3/4 500 445 315 230 1 1/8 1/2 5/16 1/8 1 500 445 315 230 1 3/8 1/2 5/16 1/8 1 1/4 500 445 315 230 1 7/16 1/2 5/16 1/8 1 1/2 800 715 530 350 5/16 1/8 1040 930 660 480 2 1/8 1/2 1/2 1/4 2 1/2 1040 930 660 480 2 5/8 5/8 1/2 1/4 2 1 5/8 1/2 2---BOLT CLAMP (TYPE B) MAX. LOAD LBS. ' PIPE SIZE w - ~I --+--t-+ .-·- T~' LL -I- ~ ~ INCHES MATL. C.S. A387-GR.22 ~~~~100~ 1 ~~ F E B J T 1/2 950 850 600 440 15/16 2 7/16 5/16 3/8 3/16 3/4 950 850 600 440 15/16 2 7/16 5/8 3/8 3/16 1 950 850 600 440 1 1/6 2 9/16 5/8 3/8 3/16 1 1/4 950 850 600 440 1 1/4 2 11/16 5/8 3/8 3/16 1 1/2 1545 w 1380 1000 745 1 13/16 41/8 1 1/16 5/8 1/4 1 1/4 1545 1380 1000 745 2 1/8 5 1/8 1 1/16 5/8 1/4 1 1/4 2 1/2 1545 1380 1000 745 1/4 1 1/4 2 2 5/16 5 3/8 1 1/16 5/8 3---BOLT CLAMP (TYPE C) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS TRAPEZE TYPE ROD HANGER, FPH-3 (FOR PIPING UP TO NPS 2 1/2) ------- _[EXISTIN~TEE~- --------------EL Y ATIACHMENT A1F-2A A ROD RF-1A l L2 1/2X2 1/2X5/16 1 B 5'-0" MAX. FPH-3 NOTES: 1.) FOR ALTERNATE CONNECTIONS TO STEEL SEE FPH-1 & 2. 2.) MAX. LOAD 0 MID SPAN (USER DEFINED) = - - - 3.) THE FOLLOI'I1NG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAI'I1NG: EL. y I PIPE suPPORT MARK No.I I FPH-3- ~--;!_ ~A 8 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS070 OCT 2004 PAGE 1 OF 1 PNFS0771 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 ANCHOR FROM GRADE OR STEEL, FPA-22 (FOR PIPING UP TO NPS 2 1/2) I ' rM ~I I I a.• /'f. . . . I I ' t's PIPE O.D. 1/4" (TYP) OR USE STRUCTURAL MEMBER < 3/16" ~ ::; • "'I "' 1/2" DIA. X 5 1/2" LG. CINCH ANCHOR BOLT (IF OTHER LENGTH REQ'D. SHOW ON ISOMETRIC). SECTION A-A ELEVATION FPA-22A 1 1/2" (TYP.) ALL AROUND 1" -.1'-->1"-.1'- t B"x 3/B"x 8" ~ ::; < • "'I q_ "' s--....J..__c+=~=~r= ELEVATION 4 9/16" DIA. HOLES IN t & 1/2" DIA. x 5 1/2" LG. CINCH ANCHOR BOLTS (MILTl OR EQUAL) 1/2" DIA. X 5 1/2" LG. CINCH ANCHOR BOLT (IF OTHER LENGTH REQ'D. SHOW ON ISOMETRIC). BASE PLATE DETAIL FPA-22B FIELD WELD TO EXIST STIEEL OR CINCH ANCHORED BY FIELD I PIPE suPPORT MARK No.I IFPA-22~~ ;: ~~ (LAST LETTIER ONLY) DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N--'/_I_N_sT_A_L_LA_TI_o_N_D_ET_A_I_Ls_ _--l GUIDE FOR INSULATED HORZ. PIPING FROM ADJ. STEEL, FPG-1 (FOR PIPING UP TO NPS 2 1/2) t J PNFS080 ocT 2004 PAGE 1 I 3 SIDES PIPE SHOE, CALL OUT SEPARATELY (TYP.) PLAN ~'-----1'-+--1 /16" CLEAR (TYP.) 111 J r==~~~~ L ======= =I= :::::::::::== EXISTING BEAM SECTION A-A I PIPE suPPORT MARK No.I I FPG-11 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. OF 1 PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 GUIDE FROM ADJACENT STEEL, FPG-3 (FOR PIPING UP TO NPS 2 1/2) L2"x 2"x 1/4"~ ~~( 2• J<..-=---.1I I 3/16 --~~>~~-~7-=t-! v--EXISTING BEAM II =-:J~ ELEVATION CLEAR (TYP.) SECTION A-A I PIPE suPPORT MARK No.I I FPG-31 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS080 ocT 2004 PAGE 3 SIDES) 1 OF 1 PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 STOP FOR HORIZONTAL PIPING FROt.i ADJACENT STEEL, FPG-6 (FOR PIPING UP TO NPS 2 1/2) PNFS080 ocT 2004 1 1 PAGE OF TO SUIT - - - ---+-----..... I ---~-- ----L----.--lHREE SIDES SHOE, CALL OUT SEPARATELY I 1 - - - - L 2 X 2X 1/4X 3" LG (TYP.) DO NOT WELD lHIS SIDE {TYP.) ELEVATION EXISTING STEEL I PIPE suPPORT MARK No.I I FPG-61 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 STOP FOR HORIZONTAL PIPING FROt.i ADJACENT STEEL, FPG-8 (FOR PIPING UP TO NPS 2 1/2) t 5/16" EXISllNG BEAM ELEVATION I PIPE suPPORT MARK No.I I FPG-81 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. It PIPE (TYP.) PNFS080 ocT 2004 PAGE 1 OF 1 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS PNFS0809 ocT 2004 1 0 1 TOWER OR STEEL, rPG-101--PA_G_E__ _F__ _--l ADJ. (FOR PIPING UP TO NPS 2 1/2) GUIDE rOR UNINSUlATED VERT. PIPING rROM TOWER PLAN INSUL. EXIST. REINF. PAD . TOWER OR STEEL 1/2" 3/16" 4"X 3"/ s·x 6" (NOTE 2) NOTES: t 1.) lHE FOLLOI't1NG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWINGS: EL. Y. ELEVATION I PIPE suPPORT MARK No.I 2.) OMIT PLATES FOR UN INSULATED VESSEL I FPG-10-r-~- J { ~N~s DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS PNFS081 ocT 2004 1 0 2 GUIDE FOR UNINSULATED VERT. PIPING FROt.i ADJ. STEEL, FPG-111--PA_G_E__ _F__ _---l (FOR PIPING UP TO NPS 2 1/2) A EXISTING STIEEL II II ___ll__yL PLAN I ' ~ I I I i -f I 1 _EL._Y = _=__---'---------------_ _-= ___=-,_ -__.J- !-=i=l ~ I ' EXISTING STIEEL C4X5.4 I 1/2" ELEVATION NOTE: lHE FOLLOI'<1NG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWINGS: EL. Y. I PIPE suPPORT MARK No.I IFPG-11-r--- { A7 ~N~S DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS GUIDE FOR UNINSULATED VERT. PIPING FROt.i ADJ. STEEL, FPG-11 (FOR PIPING UP TO NPS 2 1/2) I ' rJtn.- EL. y ________A__~~-----~ I I 1. 1 II --------- I===J] iII I 1--------.,1:7--- I I I ~ II I IIlli! I EL. y ! ~-----Ul-J_ ' 1/4" I I I ELEVATION ALTERNATE CONNECTIONS ADJACENT TO COLUMN A EL. y I _____________ _,_ I 1/4" A ELEVATION ALTERNATE CONNECTIONS ADJACENT TO BEAM DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS081 ocT 2004 2 0 2 t--PA_G_E__ _F__ _----l PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS GUIDE FOR VERTICAL PIPING, FPG-17 (FOR PIPING UP TO NPS 2 1/2) PNFS081 OCT 2004 PAGE 1 OF 3 ----,kl<----!1. 6" CLEAR (TYP.) 1/2" 1" FS-1 I I / '---'"" 1 1/2"x 1/4"X 3" LG. (TYP. 2) PLAN FPG-17A SPECIFY ON ISO IF OlHER lHAN 1/2 LENGlH OF SHOE (TYP.) EXIST. PAD (TYP.) 'b I -;... ELEVATION FPG-17A NOTES: 1.) OMIT PLATE FOR UNINSULATED VESSELS AND WELD C4X5.4 CHANNEL . - - - - - - - - - - - - - - - , To PAD. 1 PIPE suPPORT MARK No.I 2.) lHE FOULOWING DIMENSIONS AND/OR L~-=-:::::===~~:..:...._.:...:...:..:J. INFORMAllON ARE SHOWN ON PIPING FPG-17~- . DRA1'11NGS: · ~ I EL Y. I \.._ ~E (LAST LETTER ONLY) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS081 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 2 OF 3 GUIDE FOR VERTICAL PIPING, FPG-17 (FOR PIPING UP TO NPS 2 1/2) 1/16" . "' CLEAR co < (TYP. '~ - u I C4X5.4 I ~I,AI< 1 1/2"X 1/4"X 3"LG (TYP. 2) I L2X2X1/4 I \9--r7--(1(TYP. 2) A PLAN FPG-178 >------ I SPECIFY ON ISO IF OTHER THAN 1/2 LENGTH OF SHOE I I I 1C EAR (INSUL. 3/B"t I Ii + I 2") I I * I EL. y ------------- ----- L-- I 3" I. I I I F=" I I C4X5.4 _ / I I I I I '""""' 6" I L2X2X1/4 I ELEVATION FPG-178 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. I I I I I I I I I I I PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS GUIDE FOR VERTICAL PIPING, FPG-17 (FOR PIPING UP TO NPS 2 1/2) PNFS081 OCT 2004 PAGE 3 OF 3 r - - - EXISTING COLUMN PLAN PLAN FPG-17-C (ALTERNATE CONN. FOR FPG-17A) FPG-17-D (ALTERNATE CONN. FOR FPG-178) FPG-17-E (ALTERNATE CONN. FOR FPG-17A) FPG-17-F (ALTERNATE CONN. FOR FPG-178) 1" CLEAR :=..;;-',!<-,~~::.=.::;;::=.:::::~ II II :I 1/4" EXISTING BEAM II --"-- ELY CHANNEL ELEVATION FPG-17-G (ALTERNATE CONN. FOR FPG-17A) FPG-17-H (ALTERNATE CONN. FOR FPG-178) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS082 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS GUIDE ADJACENT TO GRADE OR STEEL, FPG-21 A&B (FOR PIPING UP TO NPS 2 1/2) OCT 2004 PAGE 1 OF 1 ELEVATION 10" 5" 4 - 9/16" DIA. HOLES IN PLATE AND 1/2" DIA. CINCH ANCHORS 5 1/2" LONG. 5" , - - L2X2X1/4X4" LONG (TYP.) 4" (TYP.) '---II!. 10"X 1 16" CLEAR (TYP.) PLAN FPG-21A (FOR NORTH - SOUTH GUIDE) FPG-218 (FOR EAST - WEST GUIDE) I PIPE suPPORT MARK No.I ~ "\..____TYPE A OR 8 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. 3/B"X 10" PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N...:./_I_Ns_T_A_L_LA_T_I_o_N_DE_T_A_IL_s_ _--1 4 WAY STOP ADJACENT TO GRADE OR STEEL, FPG-21 C (FOR PIPING UP TO NPS 2 1/2) II I I _ PNFS0821 ocT 2004 1 1 PAGE OF \ I I ---FPS-30 _: :!: :=-:;.t§~t.,.d~·~~~L~:. . . i~Ji!i~.b~. . !ib,. ..'..... TOP OF FINISHED GRADE ELEVATION 10" 9/16" DIA. HOLES IN PLATE AND 1/2" DIA. CINCH ANCHORS 5 1/2" LONG. (TYP.) ~-L2X2X1/4X3" LONG (TYP.) ---- 3. (TYP.) "---- t 3/B"x 1o·x 1o" 1 16" CLEAR (TYP.) PLAN FPG-21C I PIPE suPPORT MARK No.I I FPG-21C I DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS HOLD DOWN SUPPORT AND HORIZONTAL GUIDE, FPG-29 (FOR PIPING UP TO NPS 2 ) EXISTING BEAM ELEVATION ELEVATION FPG-29A FPG-29B IPE SLEEVE FOR FPG-29B ONLY. SECTION 'A-A' NOTES: 1.) STUD DIA. IS 1/16" LESS THAN HOLE SIZE 'H' IN TABLE. 2.) PROVIDE EACH STUD 1'11TH TWO HEX NUTS. 3.) THE FOLLOI'I1NG DIMENSIONS AND/OR INFORMATION ARE SHOI'Illl ON PIPING DRAI'I1NG: EL. y STUD SIZE DISC SPRING (BY USER) FPG 29B ONLY PIPE SLEEVE SIZE 7/8" BY USER 1 1/4" XXS 1" BY USER 1 1/2" xxs I PIPE suPPORT MARK No.I I g FPG-29 TYPE (LAST LETTER ONL HOLD DOI'Illl TYPE -~--~ X PIPE SIZE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS082 OCT 2004 PAGE 1 OF 2 =- =- PNFS0828 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ' ' OCT 2004 PAGE 2 OF 2 HOLD DOWN PIPE SUPPORT AND HORIZONTAL GUIDE, FPG-29 (FOR PIPING UP TO NPS 2) I .... l_! I I' --., ----- ' f'\1114·V '1- ----- (TYP.) -- ' I I' I ' ' ' I' ~~ E t.41NIMU ~ 5 RADIUS (M.R.) I ~~ c D ' ' ' I ~ I' .. D A MINIMUM RADIUS M.R. 1T 2T T 3/16" 1/4" I 1/4" { ·~ I ~ F G I' I> I I I I "....-- ' G I "'-H Jr F i( I -~ i\ ' ( I( I I ! J' 8 I' (> I( I' > I I I I I I : I !( I I rI- I "'-H r JI' HOLD DOWN I Jr' 8 HOLD DOWN II FPG-29A & FPG-298 MARK NO. FPG-29A-1 FPG-298-1 FPG-29A-1 1/2 FPG-298-1 1/2 FPG-29A-2 FPG-298-2 PIPE SIZE A 8 c D E F G H R T 1" 7 3/8" 2 1/2" 1 3/8" 3" 5/16" 2 1/2" 1 1/4" 15/16" 11/16" 3/16" 1 1/2" a· 2 13/16" 2" 3" 1/2" 2 1/2" 1 1/4" 15/16" 1" 3/16" 2" 9 5/8" 3 3/8" 2 3/8" 3 5/8" 11/16" 3 1/2" 1 1/2" 1 1/16" 1 7 /32" HOLD DO\\'Iol I DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. 1/4" li ') PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N--'/_I_N_sT_A_L_LA_TI_o_N_D_ET_A_I_Ls_ _--l WELDING LUG, ATF-1 (FOR PIPING UP TO NPS 2 1/2) PNFS0850 ocT 2004 PAGE 8 MIN. I I -- ttl --~-- '=f./ t c~ 1--- ---r------ - - 1'- ~ ' I i ELEVATION ROD SIZE PIN OR BOLT A MAX. LOAD (USER DEFINED) 3/8" 1/2" 1 1/4" 2 1/2" 3" 1/4" 9/16" USER DEFINED 8 1/2" 5/8" 1 1/4" 2 1/2" 3" 1/4" 11/16" USER DEFINED TYPE R 8 MIN. ~ 3/16"V D MIN. T H I PIPE suPPORT MARK No.I ~TYPE DIMENSIONS ARE GIVEN IN FlEET AND/OR INCHES. 1 OF 1 =- =- ' ' v -- ,V TYP. 3/16" PNFS0851 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 WELDING CLIP, ATF-2 (FOR PIPING UP TO NPS 2 1/2) (l rr s ---- _l'"~" ·~=" I ' I ' I ' I :i I :i I ' I ' I ' ---,--1--r--- < : I : w ' j ! B/2 ,L B l ' ELEVATION TYPE ROD SIZE A B s T z MAXIMUM RECOMMENDED LOAD (USER DEFINED) A 3/8" 2 7/8" 2" 1 1/4" 1/4" 7/16" USER DEFINED B 1/2" 2 7/8" 2" 1 1/4" 1/4" 9/16" USER DEFINED IPIPE SUPPORT MARK No.I ~ TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. =- =- PNFS0852 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ' ' OCT 2004 PAGE 1 OF 1 WELDING CLIP, ATF-3 (FOR PIPING UP TO NPS 2 1/2) [_~'~"=~ --- / ' ~.':'," ~-~ r H ::.:. ~:; r--< ........ f~J c ~ rc rc .._ rc __ "' w ---$ I : j r-:J s ------------ TYP~ ,. 3/16 ( - r ! B/2 L 'I B l ' ELEVATION TYPE ROD SIZE BOLT SIZE R B D MIN. s T H MAXIMUM RECOMMENDED LOAD (USER DEFINED) A 3/8" 1/2"X 2 1/2" 7/8" 2" 2" 1 1/4" 1/4" 9/16" USER DEFINED B 1/2" 5/8"X 2 1/2" 7/8" 2" 2" 1 1/4" 1/4" 11/16" USER DEFINED I PIPE SUPPORT MARK No.I ~ TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS HANGER ATTACHMENT, ATF -4 (FOR PIPING UP TO NPS 2 1/2) PNFS085 OCT 2004 PAGE 1 OF 1 EXISTING CHANNEL --r.. L2 1/2X2 1/2X5/16 I I t================== =:J I I I I 3/16" .,l I I EL. y I I I I 6" r J,.. I I I I I I I ----------1 ---------, I ' 11/'r ELEVATIONS ALTERNATE CONNECTION ATF-4A ATF-4B DESIGN LOAD: MAX. LOAD (USER DEFINED) = USER DEFINED NOllES: 1.) EXISTING BEAM SHALL BE INVESTIGAllED FOR ADDITIONAL ECCENllRIC LOAD. 2.) THE FOLLOWING DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAWINGS: EL. Y I PIPE suPPORT MARK No.I ~~E "\._ HOLEDIA. (LAST LETllER ONLY) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS085 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 3 HANGER ATTACHMENT, ATF-7 (FOR PIPING UP TO NPS 2 1/2) EXISTING BEAM~ ! TIll L3X 3X 3/8 HOLE DIA. = BOLT DIA. Iii ' A 1'-6" MAX. ELEVATION A11F-7A NOTE: DESIGN LOAD: 1.) EXISTING SUPPORTING MEMBERS TO BE CHECKED FOR ADDITIONAL PIPING LOAD AND TORSION. 2.} THE FOLLO'MNG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRA'MNG: MAX. VERT. LOAD (USER DEFINED) = USER DEFINED EL. y I PIPE suPPORT MARK No.I IATIF-7~ A TYPE (LAST LETTER ONLY} DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. + 1/16" PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N--'/_I_N_sT_A_L_LA_TI_o_N_D_ET_A_I_Ls_ _--l HANGER ATTACHMENT, ATF-7 (FOR PIPING UP TO NPS 2 1/2) PNFS085 ocT 2004 PAGE 2 OF 3 L3X 3X 3/B HOLE DIA. = BOLT DIA. A 1'-6" MAX. ELEVATION ATF-78 DESIGN LOAD: MAX. VERT. LOAD (USER DEFINED) = USER DEFINED DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. + 1/16" PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N--'/_I_N_sT_A_L_LA_TI_o_N_D_ET_A_I_Ls_ _--l HANGER ATTACHMENT, ATF-7 (FOR PIPING UP TO NPS 2 1/2) PNFS085 ocT 2004 3 3 PAGE OF /.L3X 3X 3/8 1'-6" MAX. A (l ' EXISTING BEAM -----111 ATF-1 JL i ' I ELEVATION ATF-7C DESIGN LOAD: MAX. VERT. LOAD (USER DEFINED) = USER DEFINED DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0857 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 SPECIAL STEEL WASHER PLATE, ATF-8 (FOR PIPING UP TO NPS 2 1/2) w r t ~ :1: --, 2 W/ f -m-:-m-v1 II i i j' II i ----+ ~---$-~:- -Jt------ 1I I ! ~----- I I lJ- I Li 1 I I EXISTING STEEL ,. ! '"'"V ~- PLAN ELEVATION DIA. ROD H DIA. D/D TYPE WXT A BAR 3"X 1/4" 3/B" 7/16" B BAR 3"X 1/4" 1/2" 9/16" 1 1/2" 1" MAX. ALLOW. LOAD LBS. II USER DEFINED USER DEFINED USER DEFINED I PIPE suPPORT MARK No.I ~TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0859 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS ') OCT 2004 PAGE 1 OF 1 HANGER ATTACHMENT, ATF-10 (FOR PIPING UP TO NPS 2 1/2) II T --------------~ HOLE DIA. H--......... '""""-""t-'"'"':7-- -----------, ~ 10 ~ < ' I!! 0 ... "' o z I ---~ ~-~ ~~~=-~ ~ -~--LSPECIFY IF OTHER THAN 4" {DIM. A v.1LL CHANGE). ELEVATIONS liQlE 1) FOR INSULAllON THICKNESS OVER 3 1/2" A DIMENSION SHALL BE 7" A NOMINAL PIPE H SIZE UP TO 1 1/2" 9/16" 1/2" 2"X 1/4" 5" 8 2" TO 2 1/2" 9/16" 1/2" 3"X 1/4" 5" TYPE I PIPE suPPORT MARK No.I IATIF-10~ TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0861 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 HANGER ATTACHMENT, ATF-11 (FOR PIPING UP TO NPS 2 1/2) II___ ,__ HOLE DIA. H I 3/1 ' --f~-~F~~ ~'II.......J~ i /~ ~mornrn .. LONG RADIUS ELBOW UNLESS OTHERWISE SPECIFIED ,I ' I I , 1 I I THAN 6" {DIM. A WILL CHANGE). I ~ I ~ I i ELEVATIONS t:!.QIE 1) FOR INSULAllON THICKNESS OVER 3 1/2" A DIMENSION SHALL BE 9" A NOMINAL PIN OR BAR SIZE H PIPE BOLT B X T A SIZE DIA. UP TO 1 1/2" 9/16" 1/2" 2"X 1/4" 7" B 2" TO 2 1/2" 9/16" TYPE I I 1/2" 3"X 1/4" I PIPE suPPORT MARK No.I I AllF-11 .::J A ~TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. 7" PROCESS INDUSTRY PRACTICES 1-----F_A_B_R_Ic_A_T_Io_N--'/_I_N_sT_A_L_LA_TI_o_N_D_ET_A_I_Ls_ _--l BRACE FOR RELIEF VALVE, ATF-14 (FOR PIPING UP TO NPS 2 1/2) PNFS086 ocT 2004 1 1 PAGE OF ~ - - - - - ----rr------ - ' ~----~-J-: ~~~ ~-~REUEF ,., ~ I I ~=H PIPE SIZE VARIES (TYP.) ' BAR 2"X 1/4" CUT--------~~g FIELD TO SUIT (TYP .) ' ! I 4J ~ i I' ELEVATION SECTION 'A-A' I PIPE suPPORT MARK No.I I ATF-141 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. VALVE PNFS086 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 BRACKET, ATF-17 (FOR PIPING UP TO NPS 2 1/2) A PIPE RADIUS A I , MIN. I' ~ i"l TO FIT 3" MIN. LONG RADIUS ELBOW UNLESS NOTED IN REMARKS. I i ~ llilli~ I/ I SHOP CUT-.... PIPE RADIUS 3" i I ' 117'""--il--; : EL. y -, I I I ' I I I I ~ ' EL. y I II-EXISTING STEEL .Jl_ I C-1-~ I ELEVATION ELEVATION ATF-17A & ATF-178 ATF-17C & ATF-17D TYPE MEMBER SIZE PIPE SIZE A L 1 1/2X 1 1/2X 1/4 UP TO 1 1/2" B L 1 1/2X 1 1/2X 1/4 UP TO 1 1/2" c L 2 1/2X 2 1/2X 5/16 2" & 2 1/2" D L 2 1/2X 2 1/2X 5/16 2" & 2 1/2" 1.) THE FOLLOI'I1NG DIMENSIONS AND/OR INFORMATION ARE SHOWN ON PIPING DRAI'I1NG: EL. y I PIPE suPPORT MARK No.I IATF-17~ TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0900 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 FORGED STEEL CLEVIS, CLF (FOR PIPING UP TO NPS 2 1/2) PNC00004 I l ~~,{ ------------------------4- • ' • :._\_' J r----- · i · I i I l"J r=~-~ ~-----1---=-::--~~ TYPE MAX. TAP MAX. PIN A NO. SIZE IN. Sl~~- p INCHES ' 1 ;= ______ [~==--J l'=U-==--l 0 D H T W MAX. LOAD INCHES INCHES INCHES INCHES 650' F. 750' F. 1 3/B" 1/2" 3 11/16"1 7/16 5/B" 5/16" 1 1/16" 610 540 2 1/2" 5/B" 3 11/16"1 7/16 5/B" 5/16" 1 1/16" 1130 1010 I PIPE suPPORT MARK No.I ~TYPE N0.1 OR 2 DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0901 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 STANDARD U-BOLT, UBF (FOR PIPING UP TO NPS 2 1/2) c w 0 DIMENSION SIZE NPS ROD SIZE c D 3/4 3/4" 1/4" 1 3/8" 2 3/4" E 2 1/8" 1 1" 1/4" 1 5/8" 2 3/4" 2 1/8" 1 1/4 1 1/4" 3/8" 2 1/16" 2 7/8" 2 1/8" 1 1/2 1 1/2" 3/8" 2 3/8" 2 1/2" 2 2" 2 1/2 2 1/2" 3" 3/8" ~ 13/16" 3 1/4" 1/2" 3 3/4" 3 7 /16" 2 1/2" 3" I PIPE suPPORT MARK No.I luBF-~PS SIZE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS STRAIGHT OR EYE ROD, RF /HF (FOR PIPING UP TO NPS 2 1/2) A w WELD EYE ROD TYPE HF A L c STRAIGHT ROD TYPE RF TYPE D E L EYE-ROD STR-ROD {DIA.) {DIA.) {LENGTH) MAX. LOAD 650" F 650" F HF-1A RF-1A 3/B" 9/16" 2 1/2" USER DEFINED USER DEFINED HF-2A RF-2A 1/2" 1/16' 2 1/2" USER DEFINED USER DEFINED I PIPE suPPORT MARK No.I ~ '\2: • UB-TYPE {1A OR 2A) TYPE {HF OR RF) DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS090 OCT 2004 PAGE 1 OF 1 PNFS091 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS OCT 2004 PAGE 1 OF 1 PIPE SHOE, FS-1 A THROUGH FS-1 D (FOR PIPING UP TO NPS 2 1/2) t 1/4" X L BANDING SLOT NOTES: D L L1 A 4" 1'-o'" 5" 8 4" 1'-6" B" c 6" 1'-o· 5" D 6" 1'-6'" B" TYPE 1.) UNLESS OTHERWISE SPECIFIED ON PIPING DRAWINGS: FOR TEMPERATURES UP TO 350~ USE 12" LONG SHOE. FOR TEMPERATURES 350~ TO 750~ USE 1'-6" LONG SHOE. I PIPE suPPORT MARK No.I I FS-1-,.~IZE TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES. PNFS0911 PROCESS INDUSTRY PRACTICES FABRICATION/INSTALLATION DETAILS CLAMPED SHOE, FS-1J THROUGH FS-1N (FOR PIPING UP TO NPS 2 1/2) OCT 2004 PAGE 1 OF 1 SPECIFY CLAMP TYPE & SIZE ON PIPING DRAWING. PER MSS SP-5a 45' it 1/4" X BANDING SLOT NOTES: D L L1 J 4" 1'-0" 5" K 4" 1'-6" a· M 6" 1'-0" 5" N 6" 1'-6" a· TYPE 1.) UNLESS OlHERWISE SPECIFIED ON PIPING DRAWINGS: FOR TEMPERATURES UP TO 350'F USE 12" LONG SHOE. FOR TEMPERATURES 350'F TO 750'F USE 1' -6" LONG SHOE. 2.) NO GALVANIZING IS PERMITTED FOR ANY COMPONENT IF STAINLESS STEEL CLAMP IS SPECIFIED. I PIPE suPPORT MARK No.I IFS-1-~IZE TYPE DIMENSIONS ARE GIVEN IN FEET AND/OR INCHES.

pdfcoffee.com pip-pnfs0001-pipe-supports-details-pdf-free

Add this document to collection(s)

Add this document to saved

Suggest us how to improve StudyLib