lOMoARcPSD|35185392
spec test power dong seingerew qrqwelrjlfjlasjf
数字化艺术 Digital Art (Peking University)
Scan to open on Studocu
Studocu is not sponsored or endorsed by any college or university
Downloaded by John Smith (regs2in@gmail.com)
lOMoARcPSD|35185392
A
B
C
D
E
4
RTL8153B 40 Pin
Reference Schematic V108
3
2
PAGE
INDEX
1.
2.
3.
4.
5.
6.
7.
8.
Title Page
POWER
CONTROLLER
Reserved Components
Optional Function
Bill Of Materials for LOM
Bill Of Materials for Dongle
Change Note
Realtek Semiconductor Corp.
1
No.2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan
Title
RTL8153B 40 Pin Reference Schematic : Index
Downloaded by John Smith (regs2in@gmail.com)
Size
A4
Document Number
RTL8153B 40 Pin Reference Schematic
Date:
Thursday, June 23, 2016
Sheet
Rev
1
of
8
lOMoARcPSD|35185392
A
5V
B
C
3.3V
D
For RTL8153B
If using external 3.3V supply please contact with FAE.
If using external 3.3V supply please contact with FAE.
(VDD33 and VDD5 pins should be connected to external 3.3V supply)
(VDD33 and VDD5 pins should be connected to external 3.3V
supply)
External 3.3V Supply
E
* Place C3 to C5 close to VDD33 pin-- 23, 33, 39,
* Place C6 to C7 close to VDD33 pin-- 11, 40
External 3.3V Supply
VDD5
VDD33
4
C1
C2
10uF
0.1uF
C3
C4
C5
C6
C7
0.1uF
0.1uF
0.1uF
1uF
1uF
C8
Reserved
C9
4.7uF / reserved
4
4.7uF / reserved
Place C8, C9 close to each VDD33 pin-- 11, 40
( reserved for Surge/ESD improvement )
Place C1 and C2 close to VDD5 pin-- 21
VDDREG5
CIN1
10uF X5R / reserved
CIN2
VDDREG33
0.1uF / reserved
Reserved
RTL8153B(1.0V source @ SWR mode/
LDO (Supported from VB version) mode)
Reserved
CIN3
4.7uF X5R / reserved
C10
Place C10 close to VDD33 pin-- 20
( reserved )
4.7uF / reserved
CIN4
0.1uF / reserved
RTL8153B
(1.0V source @ SWR mode)
No bead should be placed on the path from VDD5 to VDDREG5.
RTL8153B (Supported from VB version)
(1.0V source @ external mode/LDO mode)
No bead should be placed on the path from VDD33 to VDDREG33.
Remove when NOT using switching regulator
1.0V
If using external 1.0V supply
please contact with FAE
3
External 1.0V Supply
Reserved
3
RTL8153B (Supported from VB version) (1.0V source @ LDO mode)
For RTL8153B
R1
0 / reserved
* Place C12 to C16 close to VDD10 pin-- 3, 8 ,19, 34, 37
* Place C17 close to VDD10 pin-- 14.
Reserved
REGOUT
LX1
VDD10
2.2uH / reserved
Reserved
C11
COUT1
0.1uF / reserved
4.7uF X5R / reserved
COUT2
C12
C13
C14
C15
C16
C17
0.1uF / reserved
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
1uF
C18
1uF /reserved
C19
1uF /reserved
VDD10_UPS
Reserved
C20
C21
1uF
0.1uF/ reserved
RTL8153B (Supported from VB version)
(1.0V source @ external mode
/ LDO mode)
RTL8153B
(1.0V source @ SWR mode)
Reserved
Place C20 close to VDD10_UPS pin-- 22 ( reserved )
Place C21 close to VDD10_UPS pin-- 22
Other than Lx, no inductor or bead should be
placed on the path from REGOUT to VDD10.
Remove when NOT using switching regulator
Place C18 and C19 close to each VDD10 pin-- 14, 19 ( reserved for power stability )
1.0V Power-Supply Configurations
2
2
For RTL8153B
3.3V source
1.0V source
LX1
Cout1,2
Cin1,2
Cin3,4
C10
C11
R1
R7
R8
5V-to-3.3V
LDO
(Dongle)
SWR
O
O
O
O
X
X
X
O
X
LDO (Supported from VB version)
X
X
O
X
O
O
O
X
O
3.3V power input pin-- 11, 20, 23, 26, 33, 39, 40
SWR
O
O
O
O
X
X
X
O
X
1.0V SWR output pin-- 28
LDO (Supported from VB version)
X
X
X
X
O
O
O
X
O
1.0V power input pin-- 3, 8, 14, 19, 34, 37
EXTERNAL (Supported from VB version)
X
X
X
X
O
O
X
X
O
1.0V UPS LDO output pin-- 22
External
3.3V (LOM)
5V power input pin-- 21, 27
3.3V LDO output pin-- 20
Note:
1. R1, R7, R8 are reserved for the convenience of changing 1.0V supply source
between SWR, LDO and external mode from RTL8153B-VB.
If only one 1.0V supply source for RTL8153B is selected for one PCB model, i.e. no
other choices are reserved:
No design change of PCB model is needed with R1/R7/R8 reserved.
1. R1 is not neccessary. Just make a path of short to replace the use of R1 on the table.
2. Please refer to the table above when using different 1.0V supply source.
2. SWR mode only
(1) R7 => 10K ohm between ENSWREG and VDD33
(2) R1/R8 => not necessary
3. External 1.0V supply is supported from RTL8153-VB when NOT using SWR
mode.
3. LDO mode only (Supported from VB version)
4. LDO mode is supported from RTL8153-VB version only when the external 3.3V (1) R8 => 10K ohm between ENSWREG and GND
(2) R1 => short REGOUT to VDD10
source is selected for VDD33/VDD5.
(3) R7 => not necessary
5. External supply only (Supported from VB version)
(1) R8 => 10K ohm between ENSWREG and GND
(2) R1/R7 => not necessary
1
1
Realtek Semiconductor Corp.
No.2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan
Title
RTL8153B 40 Pin Reference Schematic : Power
Size
Custom
Document Number
RTL8153B 40 Pin Reference Schematic
Monday, June 27, 2016
Date:
Downloaded by John Smith (regs2in@gmail.com)
Sheet
Rev
2
of
8
lOMoARcPSD|35185392
A
B
C
RJ45 Connector + Transformer
D
E
Controller
U1
CON1
4
3
4
FGND DA+
FGND DADB+
GH1 DC+
GH2
DCDBDD+
DD-
11
12
13
14
15
16
17
18
PJ1
PJ2
PJ3
PJ4
PJ5
PJ6
PJ7
PJ8
MCT0
MCT1
MCT2
RJ45
75
75
75
75
MCT3
13
14
15
16
17
18
19
20
21
22
23
24
MX4MX4+
MCT4
MX3MX3+
MCT3
MX2MX2+
MCT2
MX1MX1+
MCT1
TD4TD4+
TCT4
TD3TD3+
TCT3
TD2TD2+
TCT2
TD1TD1+
TCT1
12
11
10
9
8
7
6
5
4
3
2
1
R2
MDI0+
MDI0-
2.49K 1%
MDI1+
MDI1-
4
R2 value should be
2.49K (1%)
for all application
MDI2+
MDI2-
VDD33
VDD33
RSET
VDD10
XTAL2
XTAL1
VDD10
VDD33
LED0/SPICSB
EECS
2
1
MDI3+
MDI3-
Refer to the page of "Power" for more detailed
configuration of R7 and R8 when using different
1.0V supply source.
C22
0.01uF
R3
R4
R5
R6
AVDD33
AVDD33
RSET
AVDD10
CKXTAL2
CKXTAL1
DVDD10
DVDD33
LED0/SPICSB
EECS
U2
C22 value should be
0.01uF-0.4uF
C23
MDI0+
MDI0VDD10
MDI1+
MDI1MDI2+
MDI2VDD10
MDI3+
MDI3-
1000P 2KV
Test Point
R9 could be saved by sharing the pull-up
resistor available on the chipset side
Three test points reserved for
debug requirement
EESK/LED1/SPISCK
GND
REGOUT
RTL8153B
VDDREG5
VDDREG33
EEDI/SPISDI/ENSWREG
EEDO/LED2/SPISDO/LANWAKEB/GPIO
DVDD33
DVDD10_UPS
VDD5
R7
supply
EESK/LED1/SPISCK
GND
REGOUT
VDDREG5
10K /reserved
VDDREG33
EEDI/SPISDI/ENSW REG
R8
EEDO/LED2/SPISDO/LANW AKEB/GPIO
VDD33
VDD10_UPS
VDD5
10K / reserved
3
VDD33
SSTX-_
SSTX+_
VDD10
SSRXSSRX+
DM
DP
VDD10
VDD33
VDD33
10K / reserved
EEDO/LED2/SPISDO/LANW AKEB/GPIO
R8 for RTL8153B (Supported from VB version)
1.0V regulator LDO mode or external 1.0V
30
29
28
27
26
25
24
23
22
21
AVDD33
U3SSTXN
U3SSTXP
U3VDD10
U3SSRXN
U3SSRXP
U2DM
U2DP
U2VDD10
AVDD33
Pull-up Resistor
MDIP0
MDIN0
AVDD10
MDIP1
MDIN1
MDIP2
MDIN2
AVDD10
MDIP3
MDIN3
R7 for RTL8153B 1.0V regulator SWR mode
11
12
13
14
15
16
17
18
19
20
3
1
2
3
4
5
6
7
8
9
10
VDD33
40
39
38
37
36
35
34
33
32
31
GST5009
TP1
0.1uF
EECS
R9
TP2
EEDI/SPISDI/ENSW REG
SSTX+_
C24
SSTX-_
C25
SSTX+
SSTX0.1uF
TP3
EESK/LED1/SPISCK
2
2
XTAL
LED (High Active)
D1
LED0/SPICSB
R10
510
1
2
XTAL1
LED
D2
X1
XTAL25M
EESK/LED1/SPISCK
R11
510
1
2
XTAL2
C26
C27
27pF
27pF
LED
D3
EEDO/LED2/SPISDO/LANW AKEB/GPIO
R12
510
1
2
LED
1
1
Refer to the page of "Reserved Components" for Using External Clock Source
Support R >= 249 ohm Resister For Single Color LED.
Refer to the page of "Reserved Components" for more optional LED configurations
Realtek Semiconductor Corp.
No.2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan
Title
RTL8153B 40 Pin Reference Schematic : Controller
Downloaded by John Smith (regs2in@gmail.com)
Size
A3
Document Number
RTL8153B 40 Pin Reference Schematic
Date:
Thursday, June 23, 2016
Rev
Sheet
3
of
8
lOMoARcPSD|35185392
A
B
C
Optional LED Configurations (Low Active)
D
USB Connector
J1
VDD33
VBUS
DD+
GND
SSTXSSTX+
GND
SSRXSSRX+
SHIELD
SHIELD
D4
LED0/SPICSB
R15
510 / reserved
2
4
E
1
EESK/LED1/SPISCK
R16
510 / reserved
LED / reserved
D5
2
1
EEDO/LED2/SPISDO/LANWAKEB/GPIO
R17
510 / reserved
2
LED / reserved
D6
1
1
2
3
4
5
6
7
8
9
10
11
R13
R14
0 / reserved
VDD5
DM
DP
0 / reserved
SSTXSSTX+
4
SSRXSSRX+
USB3_CON / reserved
LED / reserved
Support R>= 249 ohm Resister For Single Color LED
R14, R16, R17 and D4, D5, D6 Reserved for Single Color Configuration ( optional )
R13, R14 are reserved for filtering power noise.
You can just make a path of short to replace the
use of R13/R14 if not needed.
D7
1 R18
LED0/SPICSB
R19
EESK/LED1/SPISCK
249 / reserved
2
249 / reserved
Dual Color LED / reserved
VDD33
USB Type-C Plug / reserved
D8
EEDO/LED2/SPISDO/LANWAKEB/GPIO
510 / reserved 2
R20
1
J2
LED / reserved
GND
TX1+
TX1VBUS
CC
D+
DSBU1
VBUS
RX2RX2+
GND
SHIELD
SHIELD
Support R>= 249 ohm Resister For Single Color LED
Support R>= 125 ohm Resister For Dual Color LED
R18, R19, R20 and D7, D8 Reserved for Single Color + Dual Color LED Configuration ( optional )
3
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
R21
J3
0 / reserved
SSRX+
SSRXRD1
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
R22
VBUS
R25
GND
TX2+
TX2VBUS
VCONN
NC
NC
SBU2
VBUS
RX1RX1+
GND
SHIELD
SHIELD
VBUS
5.1K
DP
DM
VBUS
0 / reserved
VBUS
VBUS
SSTXSSTX+
3
D9
1
LED0/SPICSB
R24
R23
249 / reserved
USB_CON - A Side
EEDO/LED2/SPISDO/LANWAKEB/GPIO
USB_CON - B Side
2
249 / reserved
R21, R22, R25 are reserved for filtering power noise.
You can just make a path of short to replace the
use of R21, R22, R25 if not needed.
VDD33
Dual Color LED / reserved
D10
EESK/LED1/SPISCK
R26
510 / reserved 2
VDD5
0 / reserved
1
LED / reserved
SPI Flash
Support R>= 249 ohm Resister For Single Color LED
Support R>= 125 ohm Resister For Dual Color LED
R23, R24,R26 and D9, D10 Reserved for Single Color + Dual Color LED Configuration ( optional )
Only support LED0+LED1 / LED0+LED2 Dual Color LED Combinations when using EEPROM or SPI Flash
VDD33
VDD33
U3
1
LED0/SPICSB
EEDO/LED2/SPISDO/LANWAKEB/GPIO 2
3
4
Reserved for TVS Components
CSB VCC
SO HOLDB
WPB SCK
GND
SI
8
7
6
5
EESK/LED1/SPISCK
EEDI/SPISDI/ENSWREG
MX25L1606E / reserved
2
2
U4
MDI0-
1
1
U5
6
6
MDI1+
MDI2-
1
1
6
6
MDI3+
VDD33
2
2
5
5
VDD33
2
2
5
5
Reserved for Using External Clock Source
R27
External Clock
0 / reserved
XTAL2
XTAL1
C28
MDI0+ 3
3
4
4
MDI1-
0.1uF / reserved
C29
MDI2+ 3
3
4
4
MDI3-
0.1uF / reserved
R27 Reserved for Using External Clock Source ( optional )
Pin36- XTAL2 is External Clock Input Pin
Pin35- XTAL1 must be connected to GND when using external clock source
AZC099-04S / reserved
AZC099-04S / reserved
Note:
1. U4, U5 and C27, C28 are reserved for line-to-line Surge and Cable ESD on the secondary side ( optional )
2. Gas Tube is for line-to-ground Surge on the primary side ( optional )
Reserved for Noise Isolation
C30
0.01uF
C31
0.01uF
C32
0.1uF
C33
0.1uF
1
1
C30 to C33 Reserved for Noise Isolation between Chassis GND and
System GND ( optional )
Realtek Semiconductor Corp.
No.2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan
Title
RTL8153B 40 Pin Reference Schematic : Reserved Components
Downloaded by John Smith (regs2in@gmail.com)
Size
C
Document Number
RTL8153B 40 Pin Reference Schematic
Date:
Thursday, June 23, 2016
Rev
Sheet
4
of
8
lOMoARcPSD|35185392
A
B
C
D
E
***For RTL8153B EEPROM Function ***
VDD33
4
U6
EECS
EESK/LED1/SPISCK
EEDI/SPISDI/ENSWREG
EEDO/LED2/SPISDO/LANWAKEB/GPIO
1
2
3
4
CS VCC
SK
NC
DI ORG
DO GND
8
7
6
5
C34
0.1uF
AT93C46/56/66
1. All components in this block are needed if EEPROM is used.
Choose 93C46 or 93C56/66 by eFUSE autoload
3
2
Realtek Semiconductor Corp.
1
No.2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan
Title
RTL8153B 40 Pin Reference Schematic : Optional Function
Downloaded by John Smith (regs2in@gmail.com)
Size
A4
Document Number
RTL8153B 40 Pin Reference Schematic
Date:
Thursday, June 23, 2016
Sheet
Rev
5
of
8
lOMoARcPSD|35185392
A
B
***RTL8153B R-BOM for LAN on Motherbaord***
4
Bill Of Materials
Jan 29,2016
Bill Of Materials
Jan 29,2016
Item
Quantity Reference
Part
_______________________________________________________
Item
Quantity Reference
Part
_______________________________________________________
1.
2.
1
14
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
1
1
2
1
1
2
3
1
1
1
4
1
3
1
1
1
4
CON1
Cout2,Cin2,Cin4,C2,C3,C4,
C5,C12,C13,C14,C15,
C16,C24,C25
C1
Cin1
Cout1,Cin3
C22
C23
C26,C27
D1,D2,D3
J1
LX1
R2
R3,R4,R5,R6
R7
R10,R11,R12
U1
U2
X1
C6,C7,C17,C21
RJ45
0.1uF
10uF
10uF X5R
4.7uF X5R
0.01uF
1000pF/2KV
27pF
LED
USB3.0 Connector
2.2uH
2.49K 1%
75
10K
510
Transformer
RTL8153B
XTAL25M
1uF
1
12
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
1
1
1
1
2
3
1
1
1
4
1
3
1
1
1
4
CON1
C2,C3,C4, C5,C11
C12,C13,C14,C15,
C16,C24,C25
C1
C10
C22
C23
C26,C27
D1,D2,D3
J1
R1
R2
R3,R4,R5,R6
R8
R10,R11,R12
U1
U2
X1
C6,C7,C17,C21
D
E
3. External mode (Supported from VB version)
2. LDO mode (Supported from VB version)
1. SWR mode ( RTL8153B)
Bill Of Materials
C
Jan 29,2016
Item
Quantity Reference
Part
_______________________________________________________
RJ45
0.1uF
10uF
4.7uF
0.01uF
1000pF/2KV
27pF
LED
USB3.0 Connector
0
2.49K 1%
75
10K
510
Transformer
RTL8153B(Supported from VB version)
XTAL25M
1uF
1.
2.
1
12
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
1
1
1
1
2
3
1
1
4
1
3
1
1
1
4
CON1
C2,C3,C4, C5,C11
C12,C13,C14,C15,
C16,C24,C25
C1
C10
C22
C23
C26,C27
D1,D2,D3
J1
R2
R3,R4,R5,R6
R8
R10,R11,R12
U1
U2
X1
C6,C7,C17,C21
RJ45
0.1uF
4
10uF
4.7uF
0.01uF
1000pF/2KV
27pF
LED
USB3.0 Connector
2.49K 1%
75
10K
510
Transformer
RTL8153B(Supported from VB version)
XTAL25M
1uF
3
3
2
2
1
1
Realtek Semiconductor Corp.
No.2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan
Title
RTL8153B 40 Pin Reference Schematic : Bill Of Materials for LOM
A
B
Downloaded by John Smith (regs2in@gmail.com)
C
D
Size
A2
Document Number
RTL8153B 40 Pin Reference Schematic
Date:
Thursday, June 23, 2016
E
R ev
Sheet
6
of
8
lOMoARcPSD|35185392
A
B
C
D
E
***RTL8153B R-BOM for USB Dongle***
4
SWR mode (RTL8153B)
Bill Of Materials
3
Jan 29,2016
LDO mode (Supported from VB version)
4
Bill Of Materials
Jan 29,2016
Item
Quantity Reference
Part
_______________________________________________________
Item
Quantity Reference
Part
_______________________________________________________
1.
2.
1
14
1.
2.
1
13
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
1
1
2
1
1
2
3
1
1
1
4
1
3
1
1
1
1
4
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
17.
15.
16.
17.
18.
19.
20.
1
1
1
1
1
2
3
1
1
1
4
1
3
1
1
1
1
4
CON1
RJ45
Cout2,Cin2,Cin4,C2,C3,C4,
0.1uF
C5,C12,C13,C14,C15,
C16,C24,C25
C1
10uF
Cin1
10uF X5R
Cout1,Cin3
4.7uF X5R
C22
0.01uF
C23
1000pF/2KV
C26,C27
27pF
D1,D2,D3
LED
J1
USB3.0 Connector
LX1
2.2uH
R2
2.49K 1%
R3,R4,R5,R6
75
R7
10K
R10,R11,R12
510
U1
Transformer
U2
RTL8153B
U3
SPI Flash
X1
XTAL25M
C6,C7,C17,C21
1uF
CON1
Cin2,C2,C3,C4, C5,C11
C12,C13,C14,C15,
C16,C24,C25
C1
Cin1
C10
C22
C23
C26,C27
D1,D2,D3
J1
R1
R2
R3,R4,R5,R6
R8
R10,R11,R12
U1
U2
U3
X1
C6,C7,C17,C21
RJ45
0.1uF
10uF
10uF X5R
4.7uF
0.01uF
1000pF/2KV
27pF
LED
USB3.0 Connector
0
2.49K 1%
75
10K
510
Transformer
RTL8153B(Supported from VB version)
SPI Flash
XTAL25M
1uF
3
2
2
1
1
Realtek Semiconductor Corp.
No.2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan
Title
RTL8153B 40 Pin Reference Schematic : Bill Of Materials for Dongle
Downloaded by John Smith (regs2in@gmail.com)
Size
A3
Document Number
RTL8153B 40 Pin Reference Schematic
Date:
Thursday, June 23, 2016
Rev
Sheet
7
of
8
lOMoARcPSD|35185392
A
B
C
D
E
Change Notice from V100 to V101
1. Modify
XTAL1 must be connected to GND when using external clock source. (Page 4)
Change Notice from V101 to V102
4
1. Add Next-Version for LDO/External mode support
2. RTL8153B only support SWR mode
4
Change Notice from V102 to V103
1. modify the typo of capacity number. (Page2, 3)
Change Notice from V103 to V104
1. modify the typo of type C SSTX/SSRX pin assignment (Page4)
2. add RTL8153B-VB or later version can support SWR and LDO dual mode. (Page2)
Change Notice from V104 to V105
1. improve the ESD/LU , change 5V domain capacitors from 4.7uF to 10uF
( page2 )
Change Notice from V105 to V106
1. recommend VDD10_UPS output pin
3
capacitors from 0.1uF to 1uF ( page2 )
Change Notice from V106 to V107
3
1.modify the typo of USB resistor number (page4)
Change Notice from V107 to V108
1. improve the IC performance , change C6,C7,C17 capacitors from 0.1uF to 1uF
( page2 )
2
2
1
1
Realtek Semiconductor Corp.
No.2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan
Title
RTL8153B 40 Pin Reference Schematic : Change Notes
Downloaded by John Smith (regs2in@gmail.com)
Size
A3
Document Number
RTL8153B 40 Pin Reference Schematic
Date:
Thursday, June 23, 2016
Rev
Sheet
8
of
8