New Leader of Marking Technology!
+
LP7200 Ink Jet Printer
Operating Manual
Fine & Clear Dots
Easy Operating
High Speed Print
Smallest Printhead
LP7200+ INK JET PRINTER
1. EXPLANATION OF PRODUCT'S NAME
1-1. Key pad
A
: View finder back light graphic LCD
B
: Model name
F1~F5 : Function key
ESC
: Escape key
CAPS : Caps key
SHIFT : Shift key
SAVE : Enter key
DOT SIZE, PURGE, PRINT SPEED, PRINT DELAY : Direct movement key
A~Z, 0~9 : Numbers, Characters key
1
LP7200+ INK JET PRINTER
1-2. Control unit
1-3. Size of products
2
LP7200+ INK JET PRINTER
1-4. Product's specification
ITEMS
Character
LP-7100+plus
LP-7200+plus
5x5, 5x7 or 10x7 One line
Font(HXW)
Character Height
Print Speed
5x5, 5x7 or 10x7 Two lines
10x16, 20x16 One line
26mm "P" Type
63mm "P" Type
14or24mm "C" T ype
33or60mm "C" T ype
Up to 170 Meters/Min(Max) "P" Type
Up to 120 Meters/Min(Max) "C" Type
Data Storage
Text 1000 Chracters/1Line (7Dots, 16Dots)
Memory Location
100 Each Memory Storage Location
Custom Characters
7 or 16(H)X122dots(W) 50 each Graphic data
LCD Display
64(H) X 128(V) Dots Back Light Graphic LCD
Font reduction
Font Reduction 0,1,2 or 3 Changeable
Print Function
Date, Real Time, Expiry date, Shift Time, Up-Counter
Single/ Double/ Light print, Repeat print, Print direction
Odd/ Even Counter, Repeat Counter
Hot key Function
Dot size, Print speed, Print delay, Purge
Keypad
Tone up Keypad 59keys, Dialogue Menu
Ink Container
2.5 Liters Stainless Steel Container(standard)
5, 14Liters container(option)
Inks
M.E.K Base "P" type
Water base "C" type
Input Signal
Photocell for Printhout, Speed Encoder
Power
90-250V AC 60Hz
Interface
RS485
Operating Temp
5-45℃
3
LP7200+ INK JET PRINTER
2. BASIC INSTALLATION OF PRODUCT
2-1. Installation using one printhead
You could install a printhead using a basic bracket as below picture and a printhead could be
mounted on the side, the top and the bottom.
2-2. Installation using two printheads
You could install 2 printheads with using basic brackets in order to mark on both sides as below picture
and printheads could be mounted on the side, the top and the bottom.
4
LP7200+ INK JET PRINTER
2-3.Basic installation of container for ink supply
You could install a standard container for ink supply shown as below. The maximum permissible
inner pressure of the container is 2kg/cm² and should be careful not to exceed it.
For optimum marking, you have to install the container within 1 meter from the printhead and adjust
inner pressure of the container within 0.2~0.3kg.
If inner pressure is too high, it could damage printhead and could not get good marking results.
if inner pressure is too low,marking quality might not be good.
For ink line of the container, we recommend that the line should be installed within 10m.
5
LP7200+ INK JET PRINTER
3. CONNECTING TO A CONNECTOR
3-1. Connecting to detective the signal of an object
By using photo sensor or mechanical switch as an outer signal for operating of the printer, the printer
is connected to I/o signal.
Connecting to printing signal by using photo sensor
The photo sensor operating to DC24V should be used. Photo sensor can be used by connecting to "COMM"
port on a control panel as below picture.
COMM PORT
PIN NO
SIGNAL
1
2
3
4
5
0V
6
7
+24V
8
9
PRINTOUT SIGNAL No.1
3-2. Connecting to printing signal by using mechanical switch
You could print contents out by using mechanical switch (I/O Signal).
Mechanical switch can be used by connecting to "COMM" PORT on a control panel as below picture.
COMM PORT
PIN NO
SIGNAL
1
2
3
4
5
0V
6
7
8
9
PRINTOUT SIGNAL No.1
6
LP7200+ INK JET PRINTER
3-3. Connecting to a speed encoder
Connecting to a speed encoder is adoptable to mark a character on a product that moving speed
of a object is not regular or on a continuous product.
The marking speed is adjusted according to purse occurred in encoder.
Speed encoder should be used for DC24V.
Speed Encoder can be used by connecting to "COMM" port on the front control panel as below.
COMM PORT
PIN NO
SIGNAL
1
2
3
4
5
0V
6
7
24 V
8
Encoder Out Signal
9
3-4. How to select a speed encoder
General specification : Use of an encoder enables letters to be marked correctly if only pulse
and wheel diameter are applied properly according to the applying conditions of font reduce
as below picture.
FONT REDUCTION : 0
ENCODER PULSE : 60
WHEEL DIAMETER : 60 mm
The normal printing-out status of 26 or 63mm Printhead
●
● ●
●
●
●
●
●●●●●
●
●
●
●
On an occasion of FONT REDUCE application : When height of a letter is reduced into a half size in
conformity with the font reduction
FONT REDUCTION : 1, 2, 3, 4, 5
ENCODER PULSE : 120
WHEEL DIAMETER : 60 mm
7
LP7200+ INK JET PRINTER
●
●
●
●
●
●
●
●●●●●
●
●
●
●
The printing-out status applied the font reduction of 26mm or 63mm
printhead. Because the height of a letter has to get short and width of a
letter has to get narrow, encoder pulse must be controlled properly.
* When FONT REDUCE is applied, proper marking letter is printed by increasing encoder pulse or
by decreasing wheel diameter at the rate of a letter's height as above.
* On an occasion of marking in conformity with FONT REDUCE, if the width of a letter is too narrow,
FONT TYPE of F2. PRINT SET can be changeable from SINGLE to LIGHT to print.
3-5. Lithium Batteries
CAUTION !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according
to the manufacturer's instructions.
3-6. Notice on an occasion of an exchange of battery
If battery is all discharged, even when the power is turned on, main menu display
doesn't show up.
If battery is exchanged and the power is turned on while the ESC button is
being pressed, LOGO display show up.
If you release ESC button about 1sec. later, it passes to main menu display and
operates normally.
On an occasion of an exchange of battery, use it after initializing the system using
F5.INITIALIZE.
8
LP7200+ INK JET PRINTER
1. BASIC COMPONENTS OF PROGRAM
1-1. Initial display
INTER MAC
+PLUS
LP7200
VER6.0
F1
F2
F3
F4
F5
>> MENU <<
: MEMORY
: PRINT
: COUNTER
: CLOCK
: INITIAL
1-2. Function Code of Initial screen
F1. MEMORY SET
F2. PRINT SET
F3. COUNTER SET
F4. CLOCK SET
F5. INITIAL SET
1-3. Directory of Function Code
F1. MEMORY SET
1. WRITE MEMORY
MEMORY ADDRESS <00-99>
CAPS-KEY
SHIFT KEY
F1:INS F2:DEL F3:P.H
2. READ MEMORY
MEMORY ADDRESS <00-99>
CAPS-KEY
SHIFT KEY
F1:INS F2:DEL F3:P.H
3. FILE DELETE
FILE NUMBER : 0
F2. PRINT SET
1. DIRECTION
1. RIGHT
2. LEFT
9
LP7200+ INK JET PRINTER
3. UP SIDE DOWN <R>
4. UP SIDE DOWN <L>
BOTH - HEAD1 - HEAD2
P.H SELECT <F2>
[SAVE]
2. PRINT DELAY
DELAY COLUMN : 00
<0 - 9999>
BOTH - HEAD1 - HEAD2
P.H SELECT <F2>
[SAVE]
3. PRINT SPEED
PRINT SPEED <0 - 60000>msec
[SAVE]
4. DOT SIZE
DOT SIZE <0 - 200>msec
[SAVE]
5. REPEAT PRINT
1.YES
2. NO
[SAVE]
6. SPEED ENCODER
ENCODER USE
ENCODER UNUSE
[SAVE]
7. NOZZLE TYPE
1. 1 X 5
2. 2 X 5
3. 1 X 7
4. 2 X 7
5. 1 X 16
[SAVE]
8. FONT TYPE
1. SINGLE <S>
2. DOUBLE<D>
3. LIGHT <L>
BOTH - HEAD1 - HEAD2
P.H SELECT <F2>
[SAVE]
10
LP7200+ INK JET PRINTER
9. FONT REDUCE
1.
2.
3.
4.
4.
5.
FONT
FONT
FONT
FONT
FONT
FONT
<0>
<1>
<2>
<3>
<4>
<5>
BOTH - HEAD1 - HEAD2
P.H SELECT <F2>
[SAVE]
0. PASSWORD OPTION
1. NO
2. YES
[SAVE]
F3. COUNTER SET
COUNTER APPLY [C]
START 000000000
STOP
000000000
REPEAT COUNT 001
SKIP[0]
YES/NO
OPT: BASE/ODD/EVEN
COUNTER APPLY<C>
BOTH - HEAD1 - HEAD2
[SAVE]
F4. CLOCK SET
1. REAL TIME CLOCK
1. YEAR <T> : 00
2. MONTH <I> : 00
3. DAY
<M> : 00
4. HOUR <H> : 00
5. MINUTE <R> : 00
[SAVE]
2. EXPIRY DATE
1. YEAR <E> : 00
2. MONTH <X> : 00
3. DAY
<P> : 00
[SAVE]
11
LP7200+ INK JET PRINTER
3. SHIFT TIME
START TIME : <01 : 00>
CYCLE TIME <2> HOUR
SET : ALPHA/NUM/NAME
SHIFT CYCLE APPLY <A>
F5. INITIAL SET
[SAVE]
1. GRAPHICS EDIT
F1: DOT DRAW→MOVE→DELETE
MEMORY ADDRESS <100-150>
[SAVE]
2. GRAPHICS READ
MEMORY ADDRESS <100-150>
3. HEAD PURGE
1. NO
2. YES
[SAVE]
4. INITIALIZE
PASSWORD : 0
[SAVE]
5. NETWORK SELECT
SELECT ID : 1
[SAVE]
6. "O" SELECT
SELECT TYPE : 0/0
7. LANGUAGE SELECT
1. ENGLISH
2. SPANISH or OTHER LANGUAGE AVAILABLE
8. MULTI COMM
12
LP7200+ INK JET PRINTER
1-4. Types and functions of possible command for combination
@ 000 - 099 : MEMORY combination command
@100 - 150 : GRAPHIC combination command
@C : Set UP COUNTER
@T : Set YY(year)
@I : Set MM(month)
@M : Set DD(date)
@H : Set HH(hour)
@R : Set mm(minute)
@N : Set ss(second)
@E : Set expiry of YY(year)
@X : Set expiry of MM(month)
@P : Set expiry of DD(date)
@A : Set SHIFT CODE
@S : Single print command
@D : Double print command
@L : Light print command
@W : Set month name (A to L)
1-5. Definition of menu display
If the nozzle type among F2 PRINT SET is not set to 2x5, 2x7, functions such as
DIRECTION, PRINT DELAY, FONT REDUCE display only BOTH on a display.
(No.2 PRINTHEAD is not displayed on a display)
13
LP7200+ INK JET PRINTER
2. DEFINITION OF PRINT-OUT FONT
2-1. Composition of basic font
●
●
●
●
●
●●●●●
●
●
SINGLE PRINT
5 X 5 DOTS MATRIX FONT
●
●
●
●
●
●
●
●●●●●
●
●
●
●
SINGLE PRINT
5 X 7 DOTS MATRIX FONT
●●
●●●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●●●●●●●●●
●●●●●●●●●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
SINGLE PRINT
10 X 16 DOTS MATRIX FONT
2-2. Composition of the applied font
Example) 5 x 7 Dots font
●
●
●●
●
●
●
●
●
●●●●●
●
●
●
●
Single Print@S
●●
●
●●
●
●●
●●
●●
●●
●●●●●●●●●●
●●
●●
●●
●●
●
●
●
●
●
●
Double Print@D
●
●
●
●
●
●
●
●
Light Print@L
2-3. Composition of up side down font
14
LP7200+ INK JET PRINTER
2-4. Example of composition of the mixed font
●●
●●●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●●●●●●●●●
●●●●●●●●●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●
●●
●
●
●
●
●●●
●
●●
● ●
●
●
●●●●●
●
●
●●●
●
●●●●
●
●
●
●
●
●●
●
●
●●●●●
●●●●●
●
●
●●●●
●
●
●●●●
●
●
●●●●
●●●
●
●
●●●●
●
●
●
●
●●●
●●●●●●●●
●●●●●●●●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●●●●●●●
●●●●●●●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●●●●●●●●
●●●●●●●●
Input : Use a combination command after using Nozzle Type <1 x 16> 16DOT PRINTHEAD.
Reference : As above, on an occasion of using 16 dot font following 2x7 dot font, In
2x7dot, combination commands, @S and @D commands, are not available
to be inputted in upper line and the lower line each.
in case of above drawing, font type of character"B" is always as font type applied
to "123" font.
2-5. Definition of print characters
Output character
○○○○○○○○○○
●
○● ● ● ● ○
○○○○○○○○○○ ● ● ○●
●○
○○○○○○○○○○●
● ○●
●○
○○○○○○○○○○●
● ○● ● ● ● ○
○○○○○○○○○○● ● ● ● ● ○●
●○
○○○○○○○○○○●
● ○●
●○
○○○○○○○○○○●
● ○● ● ● ● ○
PRINT DELAY
CHARACTER
CHARACTER SPACE
2-6. Composition of graphic
Up to max. 124 Column(Width) of graphic can be set.
- Moving sequence of graphic key
DRAW<F1> ▶ MOVE<F1> ▶ DELETE<F1>
- Composition of 16 Dots Graphic
Up to Max.124 columns(in width) can be inputted.
15
LP7200+ INK JET PRINTER
- Graphic composition of 7 Dots
Up to Max.124 columns(in width) can be inputted.
- Definition of Graphic space
On occasion of mixed print of Graphic and Text, character space is as next.
ex) Combination of 7 Dots Graphic and Text
ex) Combination of 16 Dots Graphic and Text
16
LP7200+ INK JET PRINTER
2-7. Composition of the reduced font characters
Font reduce print is a function which can print out the character by adjusting the character's
height by printhead's angle. When printhead is vertical, it prints out as below.
By adjusting printhead's angle, you could set font correctly.
●
●
●
●
●
●
●
●●●●●
●
●
●
●
SINGLE PRINT
FONT : 0
VERTICAL PRINTHEAD
●
○● ●
○○●
●
○○○●
●
○○○○● ● ● ● ●
○○○○○●
●
○○○○○○●
●
●
○○● ●
○○○○●
●
○○○○○○●
●
○○○○○○○○● ● ● ● ●
○○○○○○○○○○●
○○○○○○○○○○○○●
0 COLUMN DELAY
1
2
3
4
5
6
SINGLE PRINT
FONT : 1
VERTICAL PRINTHEAD
0 COLUMN DELAY
2
4
6
8
SINGLE PRINT
10
FONT : 2
12
VERTICAL PRINTHEAD
●
●
●
○○○● ●
○○○○○○●
●
○○○○○○○○○●
●
○○○○○○○○○○○○● ● ● ● ●
○○○○○○○○○○○○○○○●
●
○○○○○○○○○○○○○○○○○○●
●
0 COLUMN DELAY
3
6
9
12
SINGLE PRINT
15
FONT : 3
18
VERTICAL PRINTHEAD
* Notice for FONT REDUCE application
- On an occasion of FONT REDUCE application a printing character may be loosen or may
not be printed correctly.
- When moving speed of an object is irregular, the loosen letters can be correct by applying
speed encoder.
- FONT REDUCE is revealed severely in height and width of character depending on moving Speed
of objects and angle declination of printhead. So, first after setting the font reduction value,
you'd better control the character directly regulating print speed and angle of the printhead.
17
LP7200+ INK JET PRINTER
2-8. Definition of printing direction
1) Right printing direction
- Use when it prints on an object moving from left to right
Output character
ABC
printhead
moving direction of an object
2) Left printing direction
- Use when it prints on an object moving from right to left
Output character
ABC
moving direction of an object
printhead
2-9. Definition of printing signal
- Printing signal works by receiving a printing signal of the mechanical switch or the
photo sensor which recognize an object to be printed .
- Once it receives printing signal, all contents set by parameter should be printed and in the
middle of printing, the repeated printing signal is neglected till all printing is over
be neglected before print-out ends.
- Printing example of Repeat Print <NO> (Applied to a packaging box or a single product)
● photo sensor
printhead
ABC123
ABC123
print of printing contents
delay
sensor off time
printing 1 cycle
sensor on time
18
moving direction
of product
conveyor
LP7200+ INK JET PRINTER
- Printing example of Repeat Print <YES> (Applied to serial products like films)
●
ABC123
delay
print
1 cycle
ABC123
delay
print
ABC123
delay
2 cycle
(print end)
print
3 cycle
sensor on time
* If recognition of objects is finished while the last printing content is being printed, it ends
after printing the contents out to the last.
* As above, even the same printing contents are repeated three times, counter adds only
once , that is, the number of times as which sensor recognized an object.
2-10. Composition of memory location
Memory locations consist of 100 text memory locations which user can select and
input and 50 graphic memory locations in which you can input the graphic of a user
character or graphic logo.
1) Explanation of text memory location
There are 100 memory locations and in one memory location, 1000 characters can
be inputted and outputted.
If input exceed the allowable limit of memory location for input, then, there would be
an error message, TEXT MEMORY FULL.
You could name 00-99 of memory locations and input them or read them on display.
By using combination command, you can call another memory location to a memory
memory location and combine them.
2) Explanation of graphic memory location
There are 50 memory locations, at which can input user characters or logo and max
6200 dots of graphic data can be inputted in whole memory locations horizontally.
One memory location can input max 16(H)or 7(H)X124(W) of graphic data.
You could name 100-50 of memory locations and input them or read them on display.
You can combine graphic data and print them. It is available to combine up to max 10.
19
LP7200+ INK JET PRINTER
3. PROGRAMMING
3-1. F1. MEMORY SET
- Inputting, saving or modifying works of the desired contents to print are available.
- Memory locations to which user can input data are total 100 and the max. 1000
characters (5X7 dot) can be inputted into 1 line.
- Memory locations into which you can input graphic data are 50 and the graphic data has to
be inputted on Graphic Mode.
- User Memory location can be associated with others and they are saved and print out.
- Working circumstance has to be set on equipment usage circumstance set (print set)
prior to inputting contents for an out-put.
- Composition of command
▶ F1 MEMORY SET
After using F1 on Keyboard or moving arrow to F1, press Save button.
Display composition of MEMORY SET
>> MEMORY SET <<
1. WRITE MEMORY
2. READ MEMORY
3. FILE DELETE
- Description of function by command
▶ 1. WRITE MEMORY
- When cursor locates at 1. Write Memory or number button 1 is pressed, you can enter
WRITE MEMORY mode and pass to the display shown as below.
- Range of User Memory location is from 00 to 99.
- Below is when nozzle type is set to 1 x 5, 1 x 7, 1 x 16.
>> WRITE
MEMORY <<
L1
Memory address<F3>:0
CAPS KEY SHIFT_KEY
F1:INS F2:DEL F4:P.H
1
LP7200+ INK JET PRINTER
Text can be inputted by L1 cursor and the text which is inputted longer than screen
moves to the left of the next line. Using ◀,▶, you can move cursor.
If <F3>key is pressed, the cursor moves to memory address. You can set memory address
that you want to set and save it.
If <F3>key is pressed without saving it, you can modify the contents again..
- To revise contents, you could use F1.INS, F2.DEL, key.
If you press the buttons of CAPS, SHIFT , a shadow figure is shown on display
and you can input large, small or special letters.
<SAVE> passes to PRINT IMAGE display after saving.
- Below is when nozzle select is set to 2 x 5, 2 x 7.
>>
WRITE
MEMORY <<
L1
L2
Memory address<F3>:0
CAPS_ KEY SHIFT_KEY
F1:INS F2:DEL F4:P.H
Text can be inputted along L1 or L2 cursor and the text which is inputted longer than
display moves to the left of the left line, using ◀,▶, you can move cursor.
When the button <F3> is pressed you can set Memory location at which you want
to save into and save it. If<F3>key is pressed without saving it, you can modify the contents
again. If you press the button of CAPS, SHIFT, a shadow figure is displayed on display and
you can input large, small or special characters.
<SAVE> pass to PRINT IMAGE display after saving.
- Below is display of PRINT IMAGE
>> PRINT
IMAGE <<
ABCDE0123
- On PRINT IMAGE display it is possible to check out graphic image, as well.
- Printing contents on set MEMORY LOCATION are printed even after you might
return to main menu or connect again after turning the power off.
2
LP7200+ INK JET PRINTER
- Operating a keypad in the middle of printing contents or photocell's detecting
an object is possible. Only, on occasion of pressing the "SAVE" button to save inputted
content, next printing contents are delayed till an input will be finished.
- Parameters such as Print Speed, Print Delay, Dot Size etc. are printed out at the same
time as an input.
- The combination of printing contents
You can call different memory location into set location and combine them.
- Example 1) combination of printing contents
Below is when nozzle select is set to 2 x 7.
>>
WRITE
MEMORY <<
*@ : Refer to Combination command
L1 ABC@002
L2 123@100
Memory address<F3>:0
CAPS_ KEY SHIFT_KEY
F1:INS F2:DEL F4:P.H
- Below is display of PRINT IMAGE
>>
PRINT
IMAGE
<<
ABCDEF
123 →
Assumption of an input of DEF at @002
Assumption of an input of arrow(→)
for @100 graphic data
- In the middle of printing out data, if you want to printout the changed contents after
changing data of @002 into GHI, call the No.1 out of F1.READ MEMORY and
print out.
- Example 2) combination of printing contents
When Nozzle Select on F2 PRINT SET is set to 1X16
Printing contents
A
YY.MM.DD
HH:mm COUNT
B
3
LP7200+ INK JET PRINTER
If you would like to input above, please input as below.
When Nozzle Select is set to 1X16
>> WRITE
L1
L2
A
MEMORY <<
@T.@I.@M
@H:@R@C
* @ : Refer to combination command
B
Press F4 button for changing to 7dot.
Memory address<F3>:0
CAPS_ KEY SHIFT_KEY
F1:INS F2:DEL F4:P.H
- Note> In case you input as above to combine the command used @ with two lines,
you have to input @ in same vertical line with using F4 button when it is set to
2X7 Dot. On screen, @ should be located same position.
If a counter input value is the number of 4 digits, "B" is printed out after the number
of 4 digits are printed out.
▶ 2. READ MEMORY
Composition of MEMORY SET display
>> MEMORY
SET <<
1. WRITE MEMORY
2. READ MEMORY
3. FILE DELETE
-By moving cursor to 2.READ MEMORY or pressing a number or pressing a number key2,
you can enter READ MEMORY and a next display will be displayed.
- By using READ MEMORY , you can call the data set on user memory location and a <SAVE>
is pressed right after calling them, the called data on PRINT IMAGE are displayed and can be
printed out directly.
- Memory locations you could call are from 00 to 99 of text memory location.
- If there are no data saved on the called memory location, EMPTY MEMORY message
will be displayed.
4
LP7200+ INK JET PRINTER
- Example) If you call 01 Location which ABC123 is inputted at.
>>
PRINT
IMAGE
<<
ABC123
▶ 3. FILE DELETE
<SAVE>
FILE DELETE display.
- FILE DELETE is used for deleting memory of the set MEMORY LOCATION.
- For File Delete, you could erase 000-150 addresses of Memory location can be set and
deleted.
- Without using FILE DELETE , if new contents are inputted on the set location in
MEMORY EDIT, the previous contents will be deleted automatically and new contents
will be inputted.
- Display of FILE DELETE
>> FILE
DELETE
<<
FILE NUMBER : 000
--------------------[SAVE]
5
LP7200+ INK JET PRINTER
3-2. F2. PRINT SET
-PRINT SET is used for changing parameters of printing contents and user can control status of
contents when user call the inputted contents and print out them.
- You should set all parameters on PRINT SET to fit a working condition before applying
equipments on the place.
- Saved parameters are applied to whole printing contents and if you revise them, the
revised contents are applied to all printing contents.
- For going back to main menu in the middle of setting up, you press ESC button and for
saving press SAVE button. If you want to return to the very previous stage of menu display
right after saving and then to main menu, press ESC once more.
- Composition of command
▶ F2 PRINT SET
Press SAVE button with F2 on keyboard or moving arrow to F2.
Composition PRINT
of PrintSET
set
>>
PRINT
SET
<<
For entire movement of the screen to
1.
2.
3.
4.
5.
DIRECTION
PRINT DELAY
PRINT SPEED
DOT SIZE
REPEAT PRINT
↓
6.
7.
8.
9.
0.
SPEED ENCODER
NOZZLE TYPE
FONT TYPE
FONT REDUCE
PASSWORD OPTION
another one, press "▲" key
↓ indicates that there is a menu display below.
- If above screen is shown, you could move to the set menu display with pressing <SAVE>
button after moving arrow button or pressing related figure button.
- Explanation of Command Function
★ Note : In modes of DIRECTION, PRINT DELAY and FONT REDUCE
No.1 Printhead
No.2 Printhead
Both Printhead are saved in order to be able to be operated separately, and
displays of these modes' are all set by 7 Nozzle type of PRINT SET.
- Types of Direct movement key
Regarding to Dot size, Print speed and Print delay, after revising the value of input with
direct movement key and saving, the key moves to related screen of Function code
6
LP7200+ INK JET PRINTER
and you could print out revised input contents.
- Variation of display composition by Nozzle select
Example 1) If nozzle select is set to one of 1x5, 1x7 and you enter DIRECTION mode,
the following will be shown as below.
>>
DIRECTION
<<
1. RIGHT
2. LEFT
3. UPSIDE DOWN<R>
4. UPSIDE DOWN<L>
[BOTH]
[SAVE]
P.H SELECT <F2>
Example 2) If nozzle select is set to one of 2x5, 2x7 and you enter PRINT DELAY mode,
the following will be shown as below.
>>
PRINT
DELAY
<<
F2 : BOTH → F2 : HEAD1 → F2 : HEAD2
DELAY COLUMN : 000
(0-9999)
Whenever F2 is pressed, order of P.H is
changed.
[BOTH]
[SAVE]
P.H SELECT <F2>
Example 3) If nozzle select is set to 1x16 and you enter Tilt mode, the following
will be shown as below.
>> FONT
REDUCE <<
▶ FONT < 0 >
FONT < 1 >
FONT < 2 >
FONT < 3 >
[BOTH]
[SAVE]
P.H SELECT <F2>
7
LP7200+ INK JET PRINTER
- Explanation of print set by function
▶ 1. DIRECTION
>>
DIRECTION
<<
1. RIGHT
2. LEFT
3. UPSIDE DOWN<R>
4. UPSIDE DOWN<L>
[BOTH]
[SAVE]
P.H SELECT
<F2>
Use ▲, ▼ for movement of up
and down.
- DIRECTION decides printing direction of printing contents.
- Refer to 2-8. Definition of Printing direction.
- If you use two printheads, you could print out different direction with No.1 and
No.2 printhead. If you want to print out same direction with 2 printheads or use
one 16dots printhead, you should set on P.H SELECT.<F2>
- Depending on circumstance of printhead installation, direction could be printed
out on the inversion.
- UP SIDE DOWN can print out characters turned up side down.
▶ 2. PRINT DELAY
>> PRINT
DELAY <<
DELAY COLUMN : 000
(0-9999)
[BOTH]
[SAVE]
P.H SELECT <F2>
- Function of PRINT DELAY is for printing contents after delaying column as much
as set values after recognizing of objects.
- Range of input value of PRINT DELAY is from 0 to 9999 and if the value
exceeds 9999, it does not be inputted.
- Refer to 2-5. Definition of Printing Character
8
LP7200+ INK JET PRINTER
▶ 3. Print
PRINTspeed
SPEED
>> PRINT
SPEED <<
PRINT SPEED : 0000msec
(0-60000)
------------------[SAVE]
- PRINT SPEED controls moving speed of solenoid valve according to moving
speed of objects.
- Low number indicates fast speed and high number means slow speed.
- Refer to 2-5. Definition of printing character.
- An input value of PRINT SPEED is affected by DOT SIZE when data is print out
and could get fast or slow.
▶ 4. DOT SIZE
>> DOT
SIZE
<<
DOT SIZE : 060msec
(0 ~ 200)
-----------------[SAVE]
- Dot size adjusts size of dot(amount of ink's spray) with adjusting open time of
solenoid valve.
- Low number indicates the open time of solenoid is short and high indicates the
open time is long.
- Range of input of dot size is 0~200 and if the range is over 200, an input
is impossible.
- Refer to 2-5. Definition of Printing character.
<Note>As DOT SIZE has an effect on PRINT SPEED directly, higher
value than regulation value causes the situation that PRINT SPEED
get slow automatically.
9
LP7200+ INK JET PRINTER
10
LP7200+ INK JET PRINTER
▶ 5. REPEAT PRINT
>> REPEAT
PRINT <<
1 : YES
2 : NO
------------------[SAVE]
- Refer to 2-9. Definition of printing signal.
- Function of Repeat print is for printing out contents continually by the set cycle
while receiving printing signal.
- If REPEAT PRINT is set to YES and Delay is set to 10, it accomplishes continuous
printing works from starting time of printing signal to its end.
- If REPEAT PRINT is set to NO, after it prints only once according to a printing signal,
it waits till next printing signal.
- Repeat print is used when you print out the same contents continually.
- For Up counter, it counts only when printing signal is detected once even
when REPEAT PRINT is operated.
- Repeat print <Yes>
printing
ABC123
DELAY
ABC123
DELAY
ABC123
DELAY
contents
printing
signal
- Repeat print <No>
printing
ABC123
ABC123
DELAY
ABC123
contents
printing
signal
11
LP7200+ INK JET PRINTER
▶ 6. SPEED ENCODER
>> SPEED ENCODER <<
1 : ENCODER USE
2 : ENCODER UNUSE
----------------[SAVE]
- SPEED ENCODER is used when object's moving speed is irregular or it prints after
receiving outer pulse signal.
- At the same time it receives printing signal (outer sensor), it also starts to receive
encoder's pulse signal. By the set parameter it prints out.
- When Encoder use is set to YES, if encoder does not work after receiving a
printing signal, then, encoder operates to be waiting status for printing till 1 cycle of
1printing is finished.
(if you turn the power off it can not remember the printing signal received
before, so some revision is possible).
- Example of ENCODER USE <YES>
●
●
●
●
●
●
●
●●●●●
●
●
○○○○○○●
●
●
●●
●
●
●
●
●●●
●●●
●
●●●●
●
●
●
●
●
●●
●
●
●●●●●
●
●
●●●●
1 column print per 1 purse
delay
1 cycle
- If SPEED ENCODER use is set to <NO>, it prints out evenly by a set print
speed value.
12
LP7200+ INK JET PRINTER
▶ 7. NOZZLE TYPE
>> NOZZLE
TYPE
<<
1. 1 X 5
2. 2 X 5
3. 1 X 7
4. 2 X 7
5. 1 X 16
-----------------[SAVE]
- Refer to 2. Composition of printing fonts
- The Function of Nozzle type is for composition of printhead and basic fonts to
be printed before using printer.
- If printing contents are inputted by setting of Nozzle type, you can print the set
basic fonts and you also could print out by combining other fonts except
basic font using combination command.
- 1 x 5 : Using one 5 dot printhead. Output 5 x 5 dots
- 2 x 5 : Using two 5 dot printheads. Output 2 lines of 5 x 5 dots
- 1 x 7 : Using one 7 dot printhead. Output 5 x 7 dots
- 2 x 7 : Using two 7 dot printheads. Output 2 lines of 5 x 7 dots
- 1 x 16 : Using one 16 dot printhead. Output 10 x 16 dots
▶ 8. FONT TYPE
>> FONT
TYPE
<<
SINGLE <S>
DOUBLE <D>
LIGHT
<L>
----------------[BOTH]
[SAVE]
P.H SELECT
<F2>
- Refer to 2-2. Composition of applied fonts
- Font type sets basic fonts to be used mainly before using a printer.
- Set of Font type is applied to every printable fonts.
- Font type can be combined with one another and inputted with using <@S,@D,@L>.
13
LP7200+ INK JET PRINTER
▶ 9. FONT REDUCE
>> FONT REDUCE <<
FONT
<0>
FONT
<1>
FONT
<2>
FONT
<3>
FONT
<4>
FONT
<5>
[HEAD1]
[SAVE]
P.H SELECT
<F2>
- Refer to 2-7 Composition of FONT REDUCE.
- Font adjusts height of printing character according to angle of printhead.
- Font 0 : No reduction applied.
- Font 1 : small angle
ABC123
ABC123
- Font 2 : medium angle
ABC123
- Font 3 : big angle -1
ABC123
- Font 4 : big angle -2
ABC123
- Font 5 : big angle -3
ABC123
▶ 0. PASSWORD OPTION
>> PASS OPTION
<<
1. NO
2. YES
[HEAD1]
P.H SELECT
[SAVE]
<F2>
- PASSWORD OPTION function is for preventing others than the designated
equipment managers from operating equipment.
- when you use this function, if you turn the power on again after
, turning it off,
a password input display will be shown and it prints out the contents inputted
before turning it off.
- Password is 4002.
- If password is inputted wrong, !!PASSWORD ERROR!! Message is represented.
- If you set this function set to 1.No, password input display would disappear
and pass to Main menu directly.
14
LP7200+ INK JET PRINTER
3-3. COUNTER SET
- It counts with receiving printing signal of Counter set, it can count number of
objects to be printed and then print out them.
- COUNTER SET can be combined with printing contents with shorten key and
be printed.
- Even after turning the power off, it counts next number remembering the number counted.
- You can check the present number of at Print set menu at any time.
- Contents of F3. COUNTER SET are modified, present printing contents are
printed into the revised.
- Counter displays a present Counter value on print image display.
- Composition of command
▶ F3 COUNTER SET
After using F3 button on keyboard or moving arrow to F3, press SAVE button.
Composition of COUNTER SET
* Refer to 3-2. Explanation of function of PRINT SET command.
>> COUNTER SET <<
START :
0
STOP : 000000000
REPEAT COUNT : 000
SKIP[0] : YES/NO
OPT : BASE/ODD/EVEN
COUNTER APPLY <C>
[BOTH]
[SAVE]
* On occasion of not using counter, press
key on keyboard.(Then, Counter is not
represented on print image display.)
* On occasion of operating the RESET of the counter,
put the cursor on START and press "SAVE"
key, and counter starts to count again by
the value set on the START.
- START : Inputs the number which will start counting. The unit is up to 9
- STOP : You could input the last number of counter
If it counts to the set number, It goes back to the set number on START
and counts again.
- REPEAT COUNT(Function of BATCH Counter) : Input number of repetitive counter.
If 3 is inputted into repetitive counter, the counter adds one more time
after counting the same number while it recognizes printing signal
three times.
A assumption of an input to START 1, STOP 5 repeat 3.
1→1→1→2→2→2→3→3→3→4→4→4→5 →5→5
15
LP7200+ INK JET PRINTER
- SKIP[0] : If four digits are printed out, 1 - 2 - 3 without "0" are printed out instead
of 0001 - 0002 - 0003 (in case of "Yes" set-up).
- OPT : BASE/ODD/EVEN Up counter setup
BASE : general up-counter mode
ODD : Odd number up-counter mode
EVEN : Even number up-counter mode
* In case of ADD or EVEN set-up, you should set a number for START of counter
in accordance with ODD or EVEN in advance.
For example, in case that START is set into 00, if you try to set up ODD, a error message
- START DATA ERROR - will be shown on display.
- COUNTER APPLY <C> : For an output after your inputting counter, use @C.
- Example of printing of counter
Assumption of input to START 1, STOP 20 .
1→2→3→ 4→ 5→ 6→ 7 →8→ 9 →10→ 11→ 12→ 13 →14→ 15→ 16→17 →18 →19→ 20
- Check for the volume of a present counter.
The present counted volume is shown on the bottom of the PRINT IMAGE
display.
>> PRINT IMAGE <<
ABC001
* Display status of 1x7, 1x16 (Nozzle select)
L1 : 0021
As above, L1 : 0021 on the bottom line indicates the present counted number
and increases whenever a sensor detects a object.
If you're on other working menu out of PRINT IMAGE display, You can check the
number counted so far by calling memory address which is being used at present
from F1.READ MEMORY.
16
LP7200+ INK JET PRINTER
- Initialization of the volume of counter (when the counter is not in use).
As below, if the COUNTER EXIT is set, the volume of COUNTER is not shown
on print image display
>> COUNTER SET <<
START :
0
STOP : 000000000
REPEAT COUNT : 000
SKIP[0] : YES/NO
OPT : BASE/ODD/EVEN
COUNTER APPLY <C>
[BOTH]
[SAVE]
!! COUNTER EXIT !!
Press
key
Return counter set menu
Press ESC Key to return main menu
- Reset of the volume of counter number.
On above display, after putting the cursor at START, press "SAVE" key, and a counter
resets.
- Reset of the COUNTER starts counting again from a initial value of counter set in
START.
3-4 CLOCK SET
- Clock set is a set-up mode for printing out present time, expiry data and shift code.
- Present time continue to be processed by BATTERY BACK-UP, even after the power is
turned off.
- Using combination shorten key, clock set could be printed out.
- Expiry data is processed the same as present time from date which is set.
- Composition of command.
▶ F4. CLOCK SET
After pressing F4 button on keyboard or moving arrow to F4, press SAVE button.
Composition of Clock set
>>
CLOCK
SET
<<
1 : REAL TIME CLOCK
2 : EXPIRY DATE
3 : SHIFT TIME
17
LP7200+ INK JET PRINTER
▶
1. REAL TIME CLOCK
>> REAL TIME <<
1. YEAR
< T > : 01
2. MONTH < I > : 03
3. DAY
< M > : 14
4. HOUR < H > : 10
5. MINUTE < R > : 45
------------------[SAVE]
2001-03-14
10 : 45 : 15
[SAVE]
[ESC]
Return
menu
Display of time inputted
- Input real time into REAL TIME CLOCK
- After inputting the time that you want by moving cursor up and down, save it.
- You can combine it with other printing contents and print them with using
shorten key of the inside of < >.
- To print out present time
Example) To print out year, month, day, hour and minute, please input on
WRITE MEMORY as below.
>> WRITE
MEMORY <<
L1 20@T.@I.@M @H:@R
Example) To print out year 2000,
Memory address<F3>:0
CAPS_KEY SHIFT_KEY
F1:INS F2:DEL F3:P.H
please input 20 before
@T
Status of PRINT IMAGE after pressing [SAVE] button shows present time into
which is converted automatically
>> PRINT
2000.08.25
IMAGE <<
17:50
- Printing contents are the same as PRINT IMAGE.
18
LP7200+ INK JET PRINTER
▶
2. EXPIRY DATE
>> EXPIRY
DATE <<
1. YEAR
< E> : 00
2. MONTH < X > : 00
3. DAY
< P > : 00
-----------------[SAVE]
- Input expiry date of set product.
- BY using shorten key in <>, you could combine it with other printing contents
and print them out.
- EXPIRY DATE is processed the same as present time from date which is set.
- EXPIRY DATE should be set into future time not into present time.
- To print EXPIRY DATE out
Example) To print out BEST BEFORE, YEAR, MONTH and DAY, you should
input them on WRITE MEMORY shown as below.
>> WRITE
MEMORY <<
Example) To print out year 2000,
L1 BEST BEFORE 20@E.@X.@P
please input 20 before
@T
Memory address<F3>:0
CAPS_KEY SHIFT_KEY
F1:INS F2:DEL F3:P.H
Status of PRINT IMAGE after pressing [SAVE] button shows the Expiry date into
which is converted automatically as blow.
>> PRINT IMAGE <<
BEST BEFORE 2001.08.25
- Printing contents are same as PRINT IMAGE.
19
LP7200+ INK JET PRINTER
▶
SHIFT CYCLE
>> SHIFT
CYCLE
<<
START TIME : <00:00>
CYCLE TIME :
0
SET : ALPHA /NUM/NAME
SHIFT CYCLE APPLY <A>
--------------------[SAVE]
By using ◀, ▶, cursor, move to right and left.
- SHIFT CYCLE is for printing working shift into Alphanumeric information after
changing as the set cycle.
- For START TIME, you input the start time of shift cycle.
- For CYCLE TIME, you set working cycle (within 24 hours).
- For SET you can set cycle period with alphanumeric information.
Using shorten key(A), you could combine it with other printing contents and
print out.
- Example) If it is set as START TIME 24:00, SHIFT CYCLE 4, SET ALPHA,
time
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
A ---------AB--------BC---------CD--------DE--------EF--------F
- If number is set on SET, working cycle is changed in order of 1 ,2 ,3, 4, 5 ,and6.
- SHIFT CYCLE APPLY
Example) To print out present time and working shift, shift time can be printed
after being inputted on WRITE MEMORY as below.
>> WRITE
MEMORY <<
L1 @H:@R @A
Memory address<F3>:0
CAPS_KEY SHIFT_KEY
F1:INS F2:DEL F4:P.H
- Status of PRINT IMAGE after pressing [SAVE] button shows that the inputted shift
is converted automatically fitting to present time and displayed.
20
LP7200+ INK JET PRINTER
>> PRINT
IMAGE <<
17.30 D
- Printing contents are same as PRINT IMAGE.
- Setting and inputting as NAME on SET.
- Put the cursor on NAME and press save, and it moves to the next display.
- Printout for shift cycle name
>> CYCLE NAME <<
* If you want to return to main menu after
NAME-1 :
NAME-2 :
NAME-3 :
NAME-4 :
------------------[SAVE]
saving, press SAVE
after moving cursor to
START TIME or CYCLE TIME.
- Inputting the set characters of working shift
CYCLE NAME is available for input 4 kinds of names.
Each name is available up to 10 characters for an input.
If CYCLE NAME is inputted, movement of working shift is available for marking
example)
NAME-1 : ABC
NAME-2 : DEF
NAME-3 : GHI
NAME-4 : 123
CYCLE TIME : If the cycle time is inputted with 6 hours printing order is same
as the next.
ABC
DEF
GHI
123
(changed by cycle of 6 hours respectively)
21
LP7200+ INK JET PRINTER
3-5 INITIAL SET
- On INITIAL SET, you could input and revise the graphic data as a user's word
and there are two functions like as Fuzzy of printhead and INTERFACE function.
- Composition of command
▶
F5. INITIAL SET
After pressing F5 button on keyboard or moving arrow to F5, press SAVE button.
Composition of INITIAL SET display
>>
1
2
3
4
5
6
:
:
:
:
:
:
INITIAL SET
<<
GRAPHIC EDIT
GRAPHIC READ
HEAD PURGE
INITIALIZE
NETWORK SELECT
"O" SELECT
▶ 1. GRAPHIC EDIT
After pressing 1 on the keypad or putting cursor on 1, press [SAVE] and it moves
to display which is available for GRAPHIC DRAW.
>> GRAPHIC
EDIT <<
DOT DRAW (F1)
MEMORY ADDRESS(F3): 00
F2 : L1
[SAVE]
- Use of Graphic key
movement into up, down, left, right
1
3
7
9
diagonal movement
- Whenever you press F1 button, it is changed to DOT DRAW → MOVE→ DELETE.
- By using shorten key @100 - @150, graphic could combine with other
printing contents and print them out.
22
LP7200+ INK JET PRINTER
- If graphic data do not correspond with nozzle type of PRINT SET, the graphic data
can't be printed out.
- You could input graphic data with setting Memory location after pressing
button F3.
- The range of graphic memory location is 00-50 and when you call it using
combination command, you should input number from 100 to 150.
- Printing out of the inputted graphic data.
Example) If you want to print after saving the graphics of ★ at 100 location,
○ at 101 location, ♠ at 102 location, you can print it out after inputting
on WRITE MEMORY.
>> WRITE
MEMORY <<
L1@100 @101 @102 ABC
Memory address<F3>:0
CAPS_KEY SHIFT_KEY
F1:INS F2:DEL F4:P.H
- Status of PRINT IMAGE after pressing [SAVE] button is shown as below
>> PRINT
IMAGE <<
★○♠ABC
* space of a graphic data
- Only graphic data drawn on display are included in the out-put contents.
- In order to connect a graphic with another, you can print them after combining
and connecting the different graphic memory addresses.
23
LP7200+ INK JET PRINTER
▶ 2. GRAPHIC READ
- If you press SAVE key after pressing No.2 key or moving arrow to No.2, a cursor
moves to the display which is able to do GRAPHIC READ.
- GRAPHIC READ can be inputted after checking or modifying the inputted graphic data.
- How to modify graphic data is the same as GRAPHIC EDIT.
>>
GRAPHIC
READ <<
DOT DRAW (F1)
MEMORY ADDRESS (F3) : 00
F2 : L1
[SAVE]
- If you revise and [SAVE] graphic data after reading them previous data is deleted
automatically.
▶ 3. HEAD PURGE
- After pressing number 3 button or moving arrow to No.3 button, press SAVE button,
and you could input PURGE as below.
- Printhead purge is for cleaning blocked nozzle or printhead.
- If you select printhead purge, all nozzle sprays with regular spot 100 times.
- Purge can be used by direct movement key on keyboard.
- PURGE is processed on status of present display and another key movement is
available after finishing 100 times of spray.
>> PURGE OPTION <<
1. NO
2. YES
-------------------[SAVE]
24
LP7200+ INK JET PRINTER
▶ 4. INITIALIZE
- After pressing No.4 button or moving an arrow to that number press SAVE, and the
cursor will enter INITIALIZE mode.
- When you use INITIALIZE mode, the whole inputted contents at Ram memory up to
now are erased and return to initialization condition.
- It is applicable to reinstall in other circumstance or in case of a change of using
printhead type.
* Note : If you use INITIALIZE mode, he whole memory will be erased. Please be careful.
- INITIALIZE display
>>
INITIALIZE
PASSWORD :
<<
0
--------------------[SAVE]
- Password is 4002 and if a password is not correct it does not operate.
- If you input the password correctly and press SAVE button, next display is shown up
and the whole inputted contents would be erased and then return to main menu
display after Initializing.
>>
INITIALIZE COMPLETE!
1
2
3
4
5
6
▶ 5. NETWORK SELECT
>> NETWORK SELECT <<
SELECT ID : 1
--------------------[SAVE]
25
INITIAL SET
:
:
:
:
:
:
<<
GRAPHIC EDIT
GRAPHIC READ
HEAD PURGE
INITIALIZE
NETWORK SELECT
"O" SELECT
LP7200+ INK JET PRINTER
- The NETWORK SELECT is a function for setting a ID No. of each controller in order
to transmit data connecting the max. 15 of LP7200+ controllers in case of
using a function of 8 .Multi communication
- For SELECT ID choose one of 1,2,3,4,5,6,7,8,9,A,B,C,D,E andF.
- Master controller should be set into 1, slave controller is to 2-F .
▶ 6. "O" SELECT
>>
"O" SELECT
<<
select using ◀, ▶ key
SELECT TYPE : O/Θ
-------------------[SAVE]
- This is function for preventing mistaking number "0" from English character "0".
- If you set "0" select into Yes, number "0" is printed out as an 0 with
an oblique line.
▶ 7. LANGUAGE SELECT
>>
LANGUAGE
<<
1. ENGLISH
2. KOREAN
-------------------[SAVE]
- After pressing a no.7 key or moving by arrow keys, pressing the SAVE key
can enter the next LANGUAGE mode.
- A choice of LANGUAGE is available adjusting to the use conditions and the
displayed letter is displayed as a selected language.
26
LP7200+ INK JET PRINTER
▶ 8. MULTI COMMUNICATION
>> MULTI COMM.
<<
1. NO
2. YES
-------------------[SAVE]
- After pressing a no.8 key or moving by arrow keys, pressing the SAVE key
can enter the next LANGUAGE mode.
- Initial setting for a function of multi communication is set into 1.NO, in order to
use it you should SAVE after choosing 2. YES.
- A function of multi communication makes it possible to connect the max. 14
of LP7200+ slave controller into one master controller.
- Only using a keypad of a master controller you can input marking contents,
call or edit yourself by the next slave controller which is in multi connected.
- A function of multi communication is available only when communication setting
of control board is set into RS-485 (Setting into RS-232 is not available and
refer to INTERFACE for setting)
- If it is set into RS-232 , 1 to 1 communication only is possible.
- Use of a function of MULTI COMMUNICATION
EX) In case of inputting ABS0123 at a number of 10 memory address of the 3rd
slave controller, you can use the fuction as follows.
>>
WRITE
MEMORY <<
L1 ABC0123
Memory address<F3>: 0
CAPS_ KEY SHIFT_KEY
F1:INS F2:DEL
▼
27
LP7200+ INK JET PRINTER
>>
WRITE
MEMORY <<
L1 ABC0123
Memory address<F3>: 10
CAPS_ KEY SHIFT_KEY
F1:INS F2:DEL
▼ [SAVE]
>>
RECEIVE
RECEIVE
ID <<
ID : 3
ERROR
▶
-------------------[SAVE]
▼ [SAVE]
!!! TRANS
OK !!!
▼
>> MEMORY SET <<
1. WRITE MEMORY
2. READ MEMORY
3. FILE DELETE
28
!!! COMM ERROR !!!
LP7200+ INK JET PRINTER
3-6 DIRECT MOVEMENT KEY
- Direct movement key can be used for prompt initial installation and revision
fitting to working circumstances.
- Direct movement keys consist of PRINT SPEED, DOT SIZE, PRINT DELAY and
PRINTHEAD PURGE right after modifications are done, printing contents are modified.
- Use of direct movement key can transfer into a display that a direct movement key
sets if you press a key within function codes or an initial display status.
- If you modify the content by using a direct movement key on PRINT IMAGE
display or press ESC key, modified content is saved and return to PRINT IMAGE
display automatically.
- Use of the direct movement key
DOT
SIZE
>>
Use of the direct movement key of DOT SIZE
DOT
SIZE
<<
DOT SIZE : 060msec
-------------------[SAVE]
PRINT
SPEED
>>
Use of the direct movement key of PRINT SPEED
PRINT SPEED <<
PRINT SPEED : 10000msec
-------------------[SAVE]
29
LP7200+ INK JET PRINTER
PRINT
DELAY
Use of the direct movement key of PRINT DELAY
>> PRINT DELAY
<<
DELAY COLUMN : 000
P.H SELECT <F2>
------------------[HEAD1]
PURGE
[SAVE]
Use of the direct movement key of PRINT HEAD PURGE
>> PRINTHEAD PURGE <<
-------------------
30
LP7200+ INK JET PRINTER
4. USE OF COMBINATION COMMAND
4-1. Definition of combination command
- Combination command could change a basic set value of font or combine
memory location each other in the middle of inputting data. And it could also
composite Data format simply with inserting present time into printing contents.
- Types of combination commands
@ 000 - 099 : Memory combination command (It could print out with combining
Text memory)
@ 100 - 150 : Graphic combination order (It could print out with combining
Graphic memory)
@C : Set an input of Up counter
@T : Set an input of YY(Year)
@I : Set an input of MM(Month)
@M : Set an input of DD(Date)
@H : Set an input of HH(Hour)
@R : Set an input of mm(minute)
@N : Set ss(second)
@E : Set an expiry of YY(Year)
@X : Set an expiry of MM(Month)
@P : Set an expiry of DD(Date)
@A : Set an input of shift mark of SHIFT CYCLE
@S : Single print command
@D : Double print command
@L : Light print command
@W : Set month name (A to L)
- Combination command consists of one @shorten key and you could
input desiring DATA with inserting above shorten key on Write Memory.
EX1. Example of combination command
Printing Contents:
ABC
123
456
DEF
ABC<7dot>123 <16dot>DEF
Explanation:<16dot>
<7dot>456
31
LP7200+ INK JET PRINTER
Nozzle Type : 1 x 16
- Inputting on WRITE MEMORY
>> WRITE
MEMORY <<
L1
L2
123
456
ABC
DEF
* Press F4 button for changing 16dot
to 7dot.
Memory address<F3>:0
CAPS_KEY SHIFT_EKY
F1:INS F2:DEL F4:P.H
EX2. Example of combination command
Contents to be printed : 2000.08.12 14:50 A 001
(year.month.day, hour:minute, working shift counter)
Explanation : When Nozzle type is set into 1X7, present time, 00(year)
08(month) 12(day) 14(hour) 50(minute), working shift into A
and counter into 001, input as below.
- Inputting on WRITE MEMORY.
>> WRITE
MEMORY <<
L1 20@T.@I.@M @H:@R
@A @C
Memory address<F3>:0
CAPS_KEY SHIFT_EKY
F1:INS F2:DEL F4:P.H
- Notice on an occasion of a combination of memory address.
Memory address is available to combine up to max 10 memory address.
The memory address which has already been combined can't be used in
combining it over 2 times.
EX3. Example of combination command (@W month name)
- It is available when you want to print an indication of the month of marking
contents into English. When @W is used, an indication of the month is
transformed into English and printed it out as below shown in the table.
month
transformed month
01 02 03 04 05 06 07 08 09 10 11 12
A B C D E F G H I J K L
32
Additional function
1) When you want to check the counter no. at screen without printing counter no.
<How to use>
1) At F3. COUNTER SET, set the START, STOP values and press <SAVE>
key.
2) At F1. MEMORY, press 1.WRITE MEMORY and then input @C.
3) Press <F3> key and input 99 (memory location you want) and press
<SAVE> key.
- Check of the current counter no.
PRINT IMAGE screen will display as below.
>> PRINT IMAGE <<
ABC001
L1 : 0021
As above, L1 : 0021 of screen means the current counter no. and it is
increased whenever sensing a product.
2) How to reset simply
In the case of not using the machine for a long time, In the case of not
moving a screen on controller, In the case of a sensor is not sensed.
*Note: If you use this function, whole memory you saved will be erased.
Please be careful to use.
<How to use>
Switch Power to ON pressing <ESC> key and then put off <ESC> key after a
while and setting values will be erased.