Approval sheet
RFDIP Series – 2520(1008)- RoHS Compliance
MULTILAYER CERAMIC DIPLEXER
Halogens Free Product
617~2690 MHz/ 3300~5950 MHz working frequency
P/N: RFDIP2506L19BT
*Contents in this sheet are subject to change without prior notice.
Page 1 of 8
ASC_RFDIP2506L19BT_V02
Aug. 2020
Approval sheet
FEATURES
1.
Miniature footprint: 2.5 X 2.0 X 0.65 mm
2.
Low Insertion Loss
3.
High Rejection Rate
4.
LTCC process
3
APPLICATIONS
1.
617~2690 MHz / 3300~5950 MHz Working Frequency
CONSTRUCTION
Top view
P7
P8
P1
P6
P5
P9
P2
P4
P3
PIN
Connection
PIN
Connection
P1
GND
P6
GND
P2
Common Port
P7
Low Band Port
P3
GND
P8
GND
P4
GND
P9
GND
P5
High Band Port
DIMENSIONS
Figure
Symbol
Dimension (mm)
L
2.50 ± 0.15
W
2.00 ± 0.15
T
0.65 ± 0.10
A
0.30 ± 0.10
B
0.40 ± 0.10
C
0.55 ± 0.10
D
0.40 ± 0.10
E
0.90 ± 0.10
F
0.30 ± 0.10
Top view
Side view
Side view
Bottom view
Page 2 of 8
ASC_RFDIP2506L19BT_V02
Aug. 2020
Approval sheet
ELECTRICAL CHARACTERISTICS
RFDIP2506L19BT
Frequency range
Insertion Loss
( at +25 ℃ )
Insertion Loss
( at -40~+85 ℃ )
Attenuation
Isolation
Specification
617 ~ 2690 MHz
3300 ~ 5950 MHz
0.40 dB max. @ 617~960 MHz
0.50 dB max. @ 1427~1661 MHz
0.50 dB max. @ 1710~2200 MHz
0.80 dB max. @ 2300~2690 MHz
0.50 dB max. @ 617~960 MHz
0.60 dB max. @ 1427~1661 MHz
0.70 dB max. @ 1710~2200 MHz
1.0 dB max. @ 2300~2690 MHz
1.0 dB max. @ 3300~3400 MHz
0.8 dB max. @ 3400~4200 MHz
0.8 dB max. @ 4400~5000 MHz
0.8 dB max. @ 5150~5950 MHz
1.1 dB max. @ 3300~3400 MHz
0.9 dB max. @ 3400~4200 MHz
0.9 dB max. @ 4400~5000 MHz
0.9 dB max. @ 5150~5950 MHz
20 dB min. @ 617~2690 MHz
18 dB min. @ 3300~3400 MHz
18 dB min. @ 1427~1661 MHz
20 dB min. @ 3400~3800 MHz
18 dB min. @ 1710~2200 MHz
20 dB min. @ 3800~4200 MHz
18 dB min. @ 2300~2690 MHz
20 dB min. @ 4400~5000 MHz
20 dB min. @ 10300~11700 MHz
20 dB min. @ 5150~5950 MHz
15 dB min. @ 15450~17550 MHz
20 dB min. @ 617~960 MHz
18 dB min. @ 1427~1661 MHz
18 dB min. @ 1710~2200 MHz
18 dB min. @ 2300~2690 MHz
18 dB min. @ 3300~3400 MHz
20 dB min. @ 3400~3800 MHz
20 dB min. @ 3800~4200 MHz
20 dB min. @ 4400~5000 MHz
20 dB min. @ 5150~5950 MHz
VSWR
2.0 max.
Impedance
50Ω
Power capacity
2W max.
Moisture sensitivity levels
MSL is LEVEL 1 (Refer to : IPC/JEDEC J-STD-020)
HBM ESD
Pass 1KV on all pins (Base on AEC-Q200-002)
MM ESD
Pass 200V (Base on EIA/JESD22-A115)
Operating & Storage Condition (Component)
Operation Temperature Range: -40C ~ +85C
Storage Temperature Range: -40C ~ +85C
Storage Condition before Soldering (Included packaging material)
Storage Temperature Range: +5 ~ +40 ℃
Humidity: 30 to 70% relative humidity
Typical Electrical Chart
Page 3 of 8
ASC_RFDIP2506L19BT_V02
Aug. 2020
Approval sheet
LAND PATTERN
Figure
Unit : mm
Line width to be designed to match 50 Ω characteristic impedance, depending on PCB material and thickness.
Page 4 of 8
ASC_RFDIP2506L19BT_V02
Aug. 2020
Approval sheet
RELIABILITY TEST
Test condition / Test method
Test item
Solderability
*Solder bath temperature：235  5C
Specification
At least 95% of a surface of each terminal
JIS C 0050-4.6
*Immersion time：2  0.5 sec
electrode must be covered by fresh solder.
JESD22-B102D
Resistance to soldering
Solder：Sn3Ag0.5Cu for lead-free
*Preheating temperature：120~150℃,
No mechanical damage.
1 minute.
Electrical specification shall satisfy the
*Solder temperature：2705C
descriptions in electrical characteristics under
heat
JIS C 0050-5.4
*Immersion time：101 sec
the operational temperature range within -40
~ 85°C.
Solder：Sn3Ag0.5Cu for lead-free
Loss of metallization on the edges of each
Measurement to be made after keeping at
electrode shall not exceed 25%.
room temperature for 242 hrs
Drop Test
JIS C 0044
*Height：75 cm
No mechanical damage.
Customer’s specification.
*Test Surface：Rigid surface of concrete or
Electrical specification shall satisfy the
steel.
*Times：6 surfaces for each units；2 times
for each side.
Vibration
JIS C 0040
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
*Frequency：10Hz~55Hz~10Hz(1min)
No mechanical damage.
*Total amplitude：1.5mm
Electrical specification shall satisfy the
*Test times：6hrs.(Two hrs each in three
mutually perpendicular directions)
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
Adhesive Strength
of Termination
JIS C 0051- 7.4.3
*Pressurizing force：
No remarkable damage or removal of the
5N ( LGA terminal series ) ； 5N(≦0603)； termination.
10N(>0603)
*Test time：10±1 sec
Bending test
JIS C 0051- 7.4.1
The middle part of substrate shall be
No mechanical damage.
pressurized by means of the pressurizing rod Electrical specification shall satisfy the
at a rate of about 1 mm/s per second until the descriptions in electrical characteristics under
deflection becomes 1mm/s and then pressure the operational temperature range within -40
shall be maintained for 51 sec.
~ 85°C.
Measurement to be made after keeping at
room temperature for 242 hours
Page 5 of 8
ASC_RFDIP2506L19BT_V02
Aug. 2020
Approval sheet
Temperature cycle
JIS C 0025
1.
303 minutes at -40C3C,
No mechanical damage.
2.
10~15 minutes at room temperature,
Electrical specification shall satisfy the
3.
303 minutes at +85C3C,
4.
10~15 minutes at room temperature,
Total 100 continuous cycles
descriptions in electrical characteristics
under the operational temperature range
within -40 ~ 85°C.
Measurement to be made after keeping at
room temperature for 242 hrs
High temperature
JIS C 0021
*Temperature：85C2C
No mechanical damage.
*Test duration：1000+24/-0 hours
Electrical specification shall satisfy the
Measurement to be made after keeping at
room temperature for 242 hrs
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
Humidity
(steady conditions)
*Humidity：90% to 95% R.H.
No mechanical damage.
*Temperature：402C
Electrical specification shall satisfy the
JIS C 0022
*Time：1000+24/-0 hrs.
Measurement to be made after keeping at
room temperature for 242 hrs
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
※ 500hrs measuring the first data then
1000hrs data
Low temperature
JIS C 0020
*Temperature：-40C2C
No mechanical damage.
*Test duration：1000+24/-0 hours
Electrical specification shall satisfy the
Measurement to be made after keeping at
room temperature for 242 hrs
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
Page 6 of 8
ASC_RFDIP2506L19BT_V02
Aug. 2020
Approval sheet
SOLDERING CONDITION
Typical examples of soldering processes that provide reliable joints without any damage are given in Fig 2,
This product could sustain by reflow process three times, and the temperature below 260 ℃.
Fig 2. Infrared soldering profile
ORDERING CODE
RF
DIP
2506
L
19B
T
Walsin
Product Code
Dimension code
Application
Specification
Packing
RF device
DIP :Diplexer
Per 2 digits of Length, Width,
Thickness :
L : 617~2690 MHz and
3300~5950 MHz
Design code
T : Reeled
e.g. :
2506 =
Length 2.5 mm,
Width 2.0 mm,
Thickness 0.6 mm
Minimum Ordering Quantity: 2000 pcs per reel.
PACKAGING
Plastic Tape specifications (unit :mm)
Index
Dimension (mm)
Index
Dimension (mm)
Page 7 of 8
Ao
2.30 ± 0.10
Bo
2.80 ± 0.10
E
1.75 ± 0.10
F
3.50 ± 0.05
ΦD
1.55 ± 0.05
T
0.80 ± 0.10
W
8.00 ± 0.10
Po
4.00 ± 0.10
P1
4.00 ± 0.10
P2
2.00 ± 0.05
ASC_RFDIP2506L19BT_V02
Aug. 2020
Approval sheet
Reel dimensions
C
Index
A
Φ178.0
Dimension (mm)
B
Φ60.0
A
B
C
Φ13.0
Taping Quantity:2000 pieces per 7” reel
CAUTION OF HANDLING
Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high reliability for
the prevention of defects, which might directly cause damage to the third party’s life, body or property.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Aircraft equipment
Aerospace equipment
Undersea equipment
Medical equipment
Disaster prevention / crime prevention equipment
Traffic signal equipment
Transportation equipment (vehicles, trains, ships, etc.)
Applications of similar complexity and /or reliability requirements to the applications listed in the above.
Storage condition
(1)
Products should be used in 6 months from the day of WALSIN outgoing inspection.
(2)
Storage environment condition.







Page 8 of 8
Products should be storage in the warehouse on the following conditions.
Temperature
: +5 to +40℃
Humidity
: 30 to 70% relative humidity
Don’t keep products in corrosive gases such as sulfur. Chlorine gas or acid or it may cause oxidization of
electrode, resulting in poor solderability.
Products should be storage on the palette for the prevention of the influence from humidity, dust and son on.
Products should be storage in the warehouse without heat shock, vibration, direct sunlight and so on.
Products should be storage under the airtight packaged condition.
ASC_RFDIP2506L19BT_V02
Aug. 2020