Uploaded by Rafa Tejeda

Econet PXP-40HF Portable X-ray Source 283008

advertisement
DOCUMENT NO.: PM-PXP40HF-0504
REVISION NO.: 4
OPERATION & SERVICE MANUAL
MODEL: PXP-40HF
(PORTABLE X-RAY UNIT)
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
CONTENTS
PART I. OPERATION MANUAL
1
General description
----------------------------------------------------------------------
3
2
Operational safety
----------------------------------------------------------------------
5
3
Working environment
----------------------------------------------------------------------
6
4
Radiation safety
----------------------------------------------------------------------
6
5
System configuration
----------------------------------------------------------------------
7
6
Function of x-ray unit
----------------------------------------------------------------------
7
7
Specifications
---------------------------------------------------------------------
8
8
Display of each parts
---------------------------------------------------------------------
9
9
Operation of the machine
----------------------------------------------------------------------
10
10
Operation mode
----------------------------------------------------------------------
11
11
Remote control function
----------------------------------------------------------------------
12
12
Technical chart for small animal
----------------------------------------------------------------------
19
13
Equine chart
----------------------------------------------------------------------
20
----------------------------------------------------------------------
8
TABLES
1
Specifications
ILLUSTRATIONS
1
Operation device & display
----------------------------------------------------------------------
9
2
Dimensions
----------------------------------------------------------------------
16
3
Labels
----------------------------------------------------------------------
17
PART II. SERVICE MANUAL
1
Notice
----------------------------------------------------------------------
21
2
Operation sheet
----------------------------------------------------------------------
21
3
Block diagram
----------------------------------------------------------------------
22
4
Operation board and layout
----------------------------------------------------------------------
23
5
Power board layout
----------------------------------------------------------------------
24
6
Calibration process
----------------------------------------------------------------------
25
7
Calibration code and data
----------------------------------------------------------------------
29
8
Error code and countermeasures
----------------------------------------------------------------------
30
9
Schematics
----------------------------------------------------------------------
31
TABLES
1
mA calibration code and data
----------------------------------------------------------------------
29
2
Filament calibration data
----------------------------------------------------------------------
29
3
Error code and measures
----------------------------------------------------------------------
30
2
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
PART I. OPERATION
1. GENERAL DESCRIPTION
1.1. OVERVIEW
PXP-40HF is one of PXP-HF portable family generators. Likewise of others, the PXP-40HF is most
compact, ultra-light weight and powerful HF inverter type of x-ray systems in this portable category. It
is designed especially for nursing home care or home care medical market and small medical clinics
as well as veterinary practitioner or battle field use. All PXP-HF family x-ray units are the ripple free HF
type of generator in producing 40~50% more powerful radiation output than conventional x-ray units in
its class. Therefore, PXP-40HF is the perfect x-ray portable unit for an indoor and outdoor medical
diagnostic practitioner in the radiographic application where requires an easy of operation and mobility.
Features are;
-Ultra light weight and compact size
-High frequency type of generator
-High output 100kV / 35mA
-APR pre-set (8) memory PROM
-Remote control software
-Built in collimator and laser pointer (option)
-Auto line compensation
-Digital readout reverse switch
-Accessories: metal carrying case, hand switch, power cord
-Power requirement: 110/220 Volt, 50 / 60 Hz
1.2. CONSOLIDATED MANUAL
This consolidated manual consists of operating and service instruction. This operator’s manual
provides PXP-40HF operating instructions for X-ray technicians, radiologists and other medical
personal trained in the use of X-ray equipment. Service manual provides installation instruction,
calibration and routine maintenance for field service personnel.
This manual is not designed to replace or substitute for certified training in the radiological or medical
field. In reading this manual, the operator should be qualified in the use of equipment of this type. This
portable X-ray system is only to be used by licensed practitioners in diagnostic, operative and postoperative procedures.
PXP-40HF portable X-ray can be used in variety of diagnostic radiographic systems such as mobile
stand or radiographic table integrated with X-ray tube mounting devices. Although many of the
features of these portable systems were developed with radiographic application in mind, operation is
described in general terms to permit the use of those features in radiographic application
3
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
1.3. SAFTY REQUIREMENT
This manual provides guideline for the safe use and operation of the portable system. The operator
should be in trained in the use of equipment of this type and should refer to this manual in conjunction
with that training.
It is the responsibility of the owner to ensure that the system is operated only by properly trained,
qualified personnel who have obtained credentials from local, state, and federal authorities where
required.
Potential hazards exist in the use of medical electronic devices and x-ray systems. All users and
operators must understand the safety and emergency procedures, and the operating instructions given
in this manual
Poskom Co., Ltd. certifies that each system complies with the Radiation Control for Health Safety Act
in Title 21, Chapter I, subchapter J of the Code of Federal Regulation in the USA and EN 60601,
general requirements for radiation protection in diagnostic X-Ray equipment for IEC 601-1-3 in
European Nations.
Poskom and distributors assume no responsibility or liability for after-sale operating and safety
practices, nor can it be responsible for personal injury or damage resulting form misuse of its portable
x-ray systems.
Please address a question and comments regarding safety issue to Poskom service organization
and/or each distributor in your region.
1.4. CAUTIONS AND WARNING
Possible hazards are associated with unsafe operation of this type of portable X-ray equipment. These
hazards are described on the following warning or caution signs with the safety precautions which
should be taken.
CAUTION
The X-ray radiation could be dangerous for patients and operators
unless following safety regulations are strictly observed.
4
Product Manual: PXP-40HF
Ltd.
2.
Poskom Co.,
OPERATIONAL SAFETY
PXP-40HF users’ safety, easy of operation and product reliability are our major concern in designing
this PXP-HF family of generators. However, it is advisable to observe the following instruction and
guideline for your additional safety in operating this portable.
A.
This product should be operated only by or under the supervision of legally qualified
persons.
B.
PXP-40HF is designed for the radiographic uses and not for fluoroscopy or other
associated applications.
C.
PXP-40HF should be used for the diagnosis, not for the therapy.
D.
PXP-40HF is specified as ClassⅠtype B equipment under the IEC 601-1,2 standard.
THE PORTABLE IS NOT PROTECTED AGAINST
INGRESSING A WATER OR LIQUIDS.
E.
Do not modify the equipment at your discretion and in case any modification is required
unavoidably, ask the help of Poskom or its authorized dealer for the service.
F.
This system has been calibrated for optimal operations.
G.
If you have any troubles with the equipment, turn off power immediately, and notify to
Poskom or its authorized dealer for their service and assistance.
H.
If you want to connect any devices made by other companies to this equipment, ask
Poskom or its authorized dealers for their instructions.
5
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
3. WORKING ENVIRONMENT
3.1 Avoid following places for the normal operation and safe storage.
A. Where the equipment is exposed to water vapor.
B. Where the equipment is exposed to direct sunlight.
C. Where the equipment is exposed to dust.
D. Where the equipment is exposed to high humidity.
E. Where there is a ventilation problem.
F. Where the equipment is exposed to salty atmosphere.
G. Where the equipment is exposed to chemicals or gas.
3.2. For sound operation of the machine, it should keep away from the place with strong vibration and
maintain proper environment and conditions.
A. Operation Environment
Temperature range
10°C ~ 40°C,
Relative Humidity Range
30% ~ 75% RH
B. Optimal Temperature and Humidity
Temperature range
17°C ~ 23°C,
Relative Humidity Range
40% ~ 60% RH
3.3. For safe storage and transportation, you must keep following range of temperature, humidity and
atmosphere.
Environment for storage and transportation
Temperature range
-25°C ~ +60°C
Relative Humidity Range
10% ~ 95% RH
4. RADIATION SAFETY
CAUTION
The ionized radiation could be dangerous for patients and operators
unless following safety regulations are strictly observed.
A. Users and operators should wear appropriate protecting devices and clothes.
B. Stay distance from the radiant sources and all the possible secondary radiation zones.
C. Eliminate all unnecessary objects near the exposure zones.
D. The distance from the focus to skin should be kept at least 20 cm.
E. For the experimental uses, please apply the lowest possible values about kV, mAs and
exposure time.
F. Be careful not to exceed the limited radiograms in the exposure area.
6
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
5. SYSTEM CONFIGURATION
5.1. PXP-40HF is a radiological device for medical uses. It should be applied for the radiographic
diagnosis and operated by qualified practitioners. Users have to comply with safety and health
regulations concerning the ionizing protection and the electrical and mechanical safety of the
medical devices.
5.2. PXP-40HF is composed of the following parts and devices: They should be firmly fixed and
connected with each other for the sound and normal operation.
A. Operation Board
B. Inverter
C. HV Tank including X-ray Tube
D. Collimator
E. Exposure Switch
F. Power Cord
5.3. Supplied outfit and documents
A. Aluminum Carrying Case
B. Operation Manual
C. Service Manual
D. Power Plug
E. Hand Switch (When you push hand switch in order to make radiography, it should be
pressed by two steps: step one is ready and step two is the exposure.)
6. FUNCTION OF X-RAY UNIT
6.1. PXP-40HF is designed and manufactured to gain the best radiographic results and long service
life of the x-ray tube.
6.2. kV and mAs setting method
A. Select the kV and mAs values using kV, mAs up/down switch.
B. APR (Anatomical Programming Radiography): Users can select kV and mAs values and
save them. (8 memory)
6.3. Parameter selection by the operator (kV/mA).
A. kV: The operator can adjust the kV value; the system automatically sets the maximum value
of mA producing the best radiographic results.
B. mAs: The operator can adjust the mAs value; the system automatically sets the minimum
value of kV producing the best radiographic result.
7
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
7. SPECIFICATIONS
[Table 1. Specifications]
Output Power
Input Power
2.4 kW
Voltage
100V-120V, 200V-240V
Phase & Frequency
Single / 50/60 Hz
Current
Short time 30A /15A
Radiography kV Range in 1kV steps
Tube voltage
current
mAs
40kV ~ 50kV
35mA
0.4 ~ 100
51kV ~ 70kV
30mA
0.4 ~ 64
61kV ~ 70kV
25mA
80 ~ 100
71kV ~ 80kV
30mA
0.4 ~ 32
71kV ~ 80kV
25mA
40 ~80
81kV ~ 90kV
25mA
0.4 ~ 40
81kV ~ 90kV
20mA
50 ~ 80
91kV ~ 100kV
20mA
0.4 ~ 50
91kV ~ 100kV
16mA
64 ~ 80
MAs Range
0.4mAs – 100mAs, 25steps
Max. kV Deviation
±7 %
Max. mAs Deviation
±10 %
Indication
kV (error code) /mAs: 7-segment LED
X-ray Tube
Model Name
D-124 TOSHIBA
Focal Spot
1.2 mmx1.2 mm
Target Angle
16 degree
Anode Heat Storage
20 kHU
Heat Dissipation
250 HU/sec
Total Filtration
2.5 mm Al eq. @ 100kV
Tube: 0.8mmAl, Colli.: 0.5mmAl, Add Al Filt.: 1.2mmAl
Compensation for the Supply Power
Automatic
Regulations
Collimator with
Type
Double slit type, Manual operation
Laser Pointer
Min. x-ray field size
≦5cm x 5cm
@1m SID
Max. x-ray field size
35cm x 35cm
@ 65cm SID
Laser Pointer
Class : ⅢA
Timer
Push button illuminator with 30 sec timer
Lamp
12V 50W Halogen
Dimension
Weight
5mW
See drawing Fig- (460mmx250mmx200mm)
12.8 kg (26.4 lb.)
8
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
8. DISPLAY OF EACH PARTS
Illustraion1. Operation devices and display
3
5
4
13
6
10
8
12
11
1
2
9
No.
Description
7
Function
1
kV indicator
Display kV value (range: 40 -100kV)
2
mAs indicator
Display mAs value (range: 0.4-100mAs)
3
Ready lamp
Lighted when you push the hand switch one time for
preparation
4
Exposure lamp
Alert lamp during x-ray exposure
5
Wait lamp
Lighted until the second exposure started
6
kV up/down switch
Select kV value by up or down buttons
7
mAs up/down switch
Select mAs value by up or down buttons
8
APR Switch (1-8)
Memory setting is available for 8 APR data
9
Store APR Data
Save the selected APR Data
10
Display reversal switch
Help to read LED value of kV, mAs reversed
11
Collimator lamp on
Switch for operation of the lamp inside the collimator
12
Laser pointer
To adjust exposure focus
13
Error lamp
Lighted in case of system problem
9
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
9. OPERATION OF THE MACHINE
9.1. OPERATION PRACTICES
A. Wear a lead apron while you make exposures.
B. Stay distance at least 2 m from the unit or extend the cord of hand switch as long as possible in
order to secure enough space for your safety.
C. Use proper field size and technical values for each procedure to minimize x-ray exposure dose
and gain the best radiographic result.
D. Be careful about the decimal point on the mAs display in order to acquire intended mAs values.
E. When you make exposure to the patient on the bed, ask visitors to leave the room first and
keep appropriate distance from the patient.
F. Pay attention to the maintenance schedule of the device and keep up with it.
G. Cumulative radiation dose usually does not exceed recommended maximum levels. However, if
you make radiographic exposures using high kV and mAs quite often, the evaluation of the
specialist is needed to check whether extra protective devices are necessary for the user or not.
WARNING
Please check weather the voltage and frequency of the power supply are in
accordance with the figures written in the system labels, which attached on the
body of the machine. The levels of voltage should move within ±10% of the
nominal values.
CAUTION
The operation of the machine should not be started unless all verifications and
connections are fully prepared.
9.2. POSITIONING OF PATIENT
A. Place the loaded cassette on the patient’s backside.
B. Arrange the SID (Focal Spot to Image Receptor Distance) using a scale located on the side of
the collimator.
C. Turn on the collimator lamp and laser pointer by pushing collimator/laser on switch.
D. Adjust the size of the x-ray beam in accordance with the film size using the x-ray field
adjustment knobs. Turn off the collimator and laser pointer after 30 seconds on the timer.
CAUTION
For the first installation of the machine or operation after long period of non-use, it
needs to be preheated to secure long service life of the tube. Following method of
pilot test will relieve the damage on the x-ray tube. Operate the machine with low kV
values (50kV 5mAs) three times in row and execute with higher values [70kV 5mAs]
three times in row again. Then high kV values [90kV 5mAs] will be applied without
big troubles or pressures on the machine.
10
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
10. OPERATION MODE
10.1.
NORMAL MODE
A. Please open the carrying case.
B. Connect power plug into the PXP-40HF device.
C. Turn on the line switch and the display will be shown up as follows.
kV
mAs
D. Select the kV values using the [6] kV up/down switch.
E. Select the mAs values using the [7] mAs up/down switch.
F. Positioning the machine at the ready condition by one time pushing of the hand switch.
G. When the [3] ready LED lighted, press the hand switch again and make exposure. During the xray exposure, x-ray LED will be lighted on.
H. After the exposure is ended, [5] “wait LED” sign will be lighted on and off for the waiting time.
10.2.
APR MODE
A. Please open the carrying case.
B. Connect power plug into the PXP-40HF device.
C. Turn on the line switch and the display will be shown up as follows.
kV
mAs
D. Select the [8] APR switch out of 1~8.
E. Select the kV values using the [6] kV up/down switch.
F. Select the mAs values using the [7] mAs up/down switch.
G. Save the selected kV and mAs figures with pushing the [9] “store” button.
H. When the [3] ready LED sign appears, press the hand switch again and make exposure.
During the x-ray exposure, the [4] X-ray LED will be lighted on.
I. After the exposure is ended, [5] “wait LED” will be lighted on and off for the waiting time.
NOTE
As it was illustrated in the front pages, the exposure switch should be pressed by
two steps. However, you can make immediate exposure in case the filament of the
tube is hot enough.
CAUTION
If you want to make exposures several times in row, wait until the [5] wait lamp is
lighted off. If the number of consecutive exposure exceeds three times (at higher
than 50mAs), wait for 3 minutes in order to prevent overheating of the machine.
11
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
11. REMOTE CONTROL FUCTION & OPERATION
11.1. INTRODUCTION
Currently, mAs, kVp and Pre-set memory techniques (Prom memory) can be selected by the operator
by depressing push buttons or by scrolling displays on a control panel. Each technique or mode
selection depends on an anatomic region or view for radiographic examination. The collimator lamp
and laser pointer is turned “on” by the lamp push-button and turned “off” by a 30 second collimator
timer run off.
Many portable operators and field users have suggested we find a better way to select an exposure
technique and parameters along with mAs, kVp and pre-set Prom memory values. Most field operators
hold portable X-Ray units with one hand, while holding the exposure hand switch with the other hand.
This makes selecting technique factors on the control panel awkward without dropping the portable
unit or hand switch. We have modified our X-ray portable software and functions of the Prep. and
Exposure hand switch to allow selection of all exposure parameters (mAs & kVp) and control of the
collimator lamp and laser beam.
The exposure hand switch consists of a two step hand switch. The first (1) stage of the hand switch is
called the “Preparation (Prep. or Ready)” stage. The second (2) stage of the hand switch is called the
“Exposure (Exp or X-Ray out)“ stage. (See drawing 1.)
All functions of the remote control described above are executed by clicking the first stage on the hand
switch which is the “Prep.” mode of operation. Each remote control function and technique value
selection is described below.
(Drawing 1)
1st stage switch = Prep. Switch
2nd stage switch = Exp. Switch
Hand switch housing
11.2.
REMOTE CONTROL MODE
12
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
The kVp and mAs setting, memory selection and collimator lamp and laser pointer illumination
functions are controlled remotely by the hand switch by pressing the “Prep.” stage push-button as
follows:
ATTENTION
Click the “Prep.” hand switch three (3) times consecutively. This will allow you
to enter in the “remote hand control” menu mode for operation.
<TRIPLE CLICK>
11.3. MEMORY SELELCTION
When you click the PREP stage hand switch quickly three (3) times, the Pre-set Memory station LED
(PXP-20HF: 1-4 / PXP-40HF & 60HF: 1-8) will blink sequentially as well as the kVp and mAs LED
readouts. Make a single (1) click with the hand switch when the desired pre-set memory station lamp
begins to blink. This will cause the pre-set memory data to be selected and displayed in the control
LCD window.
NOTE
All pre-set memory data should be entered and stored at each memory station (PXP-20HF: 1-4 /
PXP-60HF: 1-8), prior to performing the above mode of operation.
11.4.
kVp SELELCTION
One (1) click of the “Prep” switch will cause the kVp LED readout to blink. You will now be in the kVp
selection menu mode. The kVp values increase by one (1) kVp unit per click of the “Prep.” switch. If
you depress and hold the prep switch for a few second, the kVp readout will increases rapidly up to
the maximum value (PXP-20HF: 90kVp / PXP-40HF & 60HF: 100kVp). The kVp readout will circulate
from lowest to highest values as long as you hold and press the button. When the desired kV readout
appears on the control display panel, release the prep hand switch and wait for a few seconds. The
kVp value will set up automatically.
13
Product Manual: PXP-40HF
Ltd.
11.5.
Poskom Co.,
mAs SELECTION
mAs selection is similar to the kVp selection mode. Click the “Prep” hand switch once to make the
mAs LED readout blink. You will be in the mAs selection menu mode. The mAs value will increase with
each click of the “Prep” switch (0.4mAs to the maximum mAs of each portable x-ray unit). If you wish
to increase the mAs value quickly, simply hold the “Prep” switch down one stage. (PX-20HF: 50mAs /
PXP-40HF & 60HF: 100mAs). The mAs readout will circulate as long as you hold the “Prep” switch.
When the desired mAs readout appears on the control display panel, release the prep hand switch
and wait for a few seconds. Then mAs value will set automatically.
11.6.
COLLIMATOR / LASER BEAM TURNED ON
ATTENTION
Click the Prep. hand switch rapidly twice. The collimator lamp and laser
pointer beam will illuminate for X-ray exposure positioning.
<DOUBLE CLICK>
With the exposure technique (mAs & kVp) set with your remote hand switch, you are ready to make a
radiographic exposure for examination. It is very important to position the right region of interest on a
patient’s anatomy. Therefore, the collimator beam must be turned on to confirm the size of region and
size of film covered. The laser beam must also be turned on for checking the precise center of the
target prior to making a final X-ray exposure. When the Prep switch is rapidly clicked twice, the
collimator lamp and laser beam will turn on simultaneously until the lamp timer (30 seconds) runs off.
However, it will turn off automatically when x-ray exposure sequence is completed.
11.7.
X-RAY EXPOSURE
WARNING
When an X-ray exposure is made in a room or outdoors, lower radiation will scatter throughout the
surrounding area. An authorized operator is expected to take precautions and is highly recommended
to ware a lead apron and gloves if necessary for your patient’s and your own protection.
After the x-ray exposure technique is selected and collimator light beam size is adjusted with the
collimator blade knob, an x-ray exposure can be made by an authorized individual of the medical clinic
or hospital.
X-RAY EXPOSURE SEQUENCE:
A. Press the Prep hand switch (1st stage) and hold
B. Press down the 2nd stage hand switch. Exposure will be
made automatically by the exposure timer.
14
Product Manual: PXP-40HF
Ltd.
< 1ST STAGE>
Poskom Co.,
<2ND STAGE>
11.8. REMOTE CONTROL OVERRIDE
NOTE TO THE USER
All of the before mentioned remote control hand switch functions and operations can also be
accomplished via the one-touch control panel. All exposure functions and parameters can be
Overridden through the main control panel prior to final exposure. (See user’s manual for
directions on how to use the main control panel)
15
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
Illustration 2. Dimension (Main Unit & Carrying Case)
1) PXP-40HF
2) CARRYING CASE (ALUMINUM)
16
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
Illustration 3. Labels
PXP-40HF Portable label sticker and location
Warning: This X-ray unit maybe dangerous to patient and operator
unless safe exposure factors and operation instruction are observed
DIAGNOSTIC X-RAY UNIT
MODEL: PXP-40HF
SER. NO.:
DATE:
Input Rating: AC220~240V, 50/60 Hz
Rating: X-ray Tube Voltage: 40~100kV
X-ray current: 20~35mA
Operation condition: Time interval between 3 exposure: 3 min
(When the mAs is higher than 50)
Filtration: Total filtration: Min 2.5 mmAl
Tube: 0.8 mmAl, collimator, 0.5 mmAl, Al Filt.: 1.2mmAl
X-ray tube (TOSHIBA), Model: D-124, Serial no.:
Focal spot: 1.2mm X 1.2mm
POSKOM
Room 405, Unitech Ville Bldg., 1141-2, Baeksuk-dong,
Ilsan-gu, Goyang, Korea
Take adequate Precautions to prevent the possibility of
any persons carelessly exposing themselves or others to
radiation.
High Voltage Tank
MODEL: HV-40
SER.NO: XXXXXX
Rating: Max. 100kV, 35mA, Max output: 2.4 kVA
POSKOM
Room 405, Unitech Ville Bldg., 1141-2, Baeksuk-dong,
Ilsan-gu, Goyang, Korea
Warning: Electric shock hazard do not remove cover
Reserve Servicing to qualified personnel.
Beam Limiting Device (Collimator)
MODEL: PCMAX-100
SER.NO: XXXXXXX
Input Rating: 12V, 50W
Min. X-ray field size: Below 5cm x 5 cm at SID 100cm
Max. X-ray field size: Below 35cm x 35cm at SID 65cm
Max. Tube Voltage: 100kV, Inherent filtration: 0.5 mmAl
POSKOM
Room 405, Unitech Ville Bldg., 1141-2, Baeksuk-dong,
Ilsan-gu, Goyang, Korea
17
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
DANGER
LASER LIGHT BEAM
DO NOT STARE INTO BEAM
Wavelength: 650 nm
Output Power: 5mW
Laser Class: III A Product
This device complies with 21 CFR CH.I Sub J Regulation
Veterinary Use only
18
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
12. TECHNIQUE CHART FOR SMALL ANIMALS
100 cm (40 Inch) SID, GRID: 103 lines / 6:1 ratio
Film/Screen: Fuji RX-U/ Rare earth
[Table 2. Chart for small animals]
Thickness (cm)
Skull / Pelvis/ Extrim kVp /(mAs)
Thorax kVp / (mAs)
Abdomen kVp / (mAs)
2-3
No grid : 50 / (0.4)
4-5
No grid : 54 / (0.4)
6-7
No grid : 54 /(0.5)
No grid: 66 / (0.4)
No grid : 60 / (0.6)
8-9
No grid : 60 /( 0.6)
No grid: 70 / (0.4)
No grid : 60 / (0.8)
10-11
66 / (1.6)
No grid: 74 / (0.4)
No grid : 60 / ( 1.0)
12-13
70 / (1.6)
78 / (0.8)
64 / (2.0)
14-15
72 / (1.6)
80 / (0.8)
68 / (2.5)
16-17
72 / (2.0)
86 / (0.8)
68 / (2.5)
18-19
74 / (2.4)
90 / (0.8)
70 / (3.2)
20-21
76 / (2.4)
90 / (1.2)
74 / (3.2)
22-23
80 / (2.4)
96 / (1.2)
80 / (4.0)
NOTE
The contents in the table are recommended for starting radiographic techniques.
The final radiography of proper image density and resolution depends on many factors. Please follow
the next adjustment and common rules if necessary.
1. Add or subtract 2 kVp for 1 cm increase or decrease in thickness of body section.
2. If films are too dark, decrease mAs value on the next lower station.
3. If films are too light, increase mAs value on the next higher station
19
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
13. EQUINE CHART
66 cm (26 Inch) Distance
400 Speed Rare Earth Film / Screen
[Table 3. Equine Chart]
ANATOMY
VIEW
High Contrast
Mid-Contrast
kV
mAs
kV
mAs
AP
66
1.2
72
0.8
LAT
66
1.0
72
0.6
P3
62
0.8
-
-
AP
66
1.2
72
0.8
LAT
66
1.0
72
0.6
AP/FLEX
66
1.2
72
0.8
LAT/OBI
66
1.0
72
0.6
SPLINT BONE
LAT
58
0.8
68
0.6
HOCK
AP/HIGH
66
1.6
72
1.0
AP/LOW
66
1.2
72
0.8
LAT
66
1.0
72
0.6
LAT
-
-
78
2.0
PA
-
-
78
4.0
AP
-
-
78
2.0
OTHER
-
-
78
1.2
NAVICULAR
FETLOCK
KNEE
STIFLE
ELBOW
ALTERNATIVE TECHNIQUES
STIFLE
LAT
45 cm distance
78
1.2
PA
45 cm distance
78
2.5
AP
65 cm distance
68
2.5
LAT
65 cm distance
68
2.0
FOAL
85 cm distance
90
0.8
300LBS
85 cm distance
100
1.2
500LBS
85 cm distance
100
4.0
SINUS
LAT
85 cm distance
88
1.2
SHOULDER
LAT
75 cm distance
86
3.2
OBI
75 cm distance
86
4.0
NAVICULAR
CHEST
20
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
PART II. SERVICE
1. NOTICE
1.1. If the output calibration is needed after periodical inspections or repairs, please observe following
rules and methods.
CAUTION
The ionized radiation is dangerous for the operator if the following
safety measures are not strictly observed.
1.2. This manual is designed to ensure correct use and operation of PXP-40HF. Please read all the
lines thoroughly before you use this equipment.
1.3. Incorrect use and operation exceeding described conditions in this manual may occur damage of
the machine and shorten its life. Particular attention must be paid to all the warnings, cautions and
notes incorporated herein.
1.4. This equipment should be used only by the legally qualified persons and practitioners.
1.5. Regarding the AC cable and software, only the one developed and supplied by Poskom should be
used.
1.6. No responsibility is taken by Poskom for any infringement of patients or other rights of the third
parties which many results from the use of this manual.
1.7. Always keep the manual at hand for your reference.
2. OPERATION SHEET
APR SWITCH 1~8
kV UP/DOWN SWITCH
21
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
LASER SWITCH
COLLIMATOR ON/OFF SWITCH
STORE SWITCH
mAs UP/DOWN SWITCH
22
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
3. BLOCK DIAGRAM
READY
HTP24-CTL-001
1
2
X-RAY
CON1
3
35312-03
HAND SWITCH
3V/35mA
LASER POINTER
CONTROL BOARD
OP PANEL
1
2
CON6
1
2
CON2
* EXPORT : NORMAL
35312-02
* DOMESTIC : NOT USED
LASER
& HT CONT.
TANK
T
2
35312-02
35312-05
CON3
1
2
3
4
5
6
7
8
9
10
11
1
2
3
4
5
THERMAL
EP_FB(-)
35312-05
35312-11
CON2
/100V_SEL
LAMP_CONT
FIL_FB
EP_CONT2
FIL_CONT1
FIL_CONT2
IP_FB(+)
EP(-)
GND
IP(+)
1
2
3
4
5
6
7
8
9
10
11
1
2
3
4
5
+5V
DGND
+12V
AGND
-12V
EP_CONT1
AGND
1
CON4
35312-11
1
2
3
4
5
CON5
35312-05
CON3
HT XFMR
T1
TB1
T1
20
1
2
3
575
T2
TB2
CON5
COM
D-124S
35312-03
HTP24-PWR-001
FG
PWR & DRIVE
T2
CON4
FILAMENT DRIVE
CB1
1
2
3
4
C1
3
2
+12.2
SHIELD GND
SHIELD LINE
C2
53258-04
3
FIL XFMR
250V/16A
5
4
3
2
1
250V/20A
53258-05
CON1
COLLIMATOR DRIVECON6
1
2
COLLIMATOR
CN1
PLUG AC MALE
LAMP
SHIELD LINE
53258-02
12V/100W
APPROVED BY
DESIGNED BY
<OrgName>
HTP-24 Main Block
CHECKED BY
DATE
Size
A3
FSCM NO.
DWG NO
Rev
00
<Cage Code>
Sheet
1
23
of
1
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
4. OPERATION BOARD AND LAYOUT
24
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
5. POWER BOARD LAYOUT
25
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
-PREPARATION
Following tools and instruments are needed.
a. Tools: Philips screwdriver No.1 & 2, Straight slot screwdriver
b. Instruments: DVM, oscilloscope (Tektro TDS 3032 and more than Equivalent)
6. CALIBRATION PROCESS
6.1. Line Power Supply
-Line switch should be at off position.
-Connect power line cord to the power outlet.
-Turn on the line switch.
-Then the LED on the operation panel illuminates.
6.2. Calibration procedures are composed of three steps.
-Tube voltage confirmation and calibration.
-Tube current confirmation and calibration.
-Filament preheat calibration
A. Calibration and Confirmation of Tube Voltage
-Turn off the line switch.
-Lift up the control panel from the unit, and then the PCB OP board appears.
-All DIP switches on the PCB OP board are turned off.
(Note: DIP switch is usually located in this
location.)
-Connect the channel one probe of the oscilloscope to TP5 (IP F/B).
-Connect the channel another one probe of the oscilloscope to TP6 (EP F/B).
Channel 1 is mA, and 35mA = 7V
Channel 2 is kV, and 40kV = 2V
-Connect the ground to TP11 (GND).
-Turn on the line switch and the display indicates as follows.
kV
mAs
-Set the kV and the mAs at 40kV and 0.4mAs (60mA). Then observe the mA waveform of the
oscilloscope channel 1.
-If it is not about 9V, adjust mA by VR3 on the OP board. Then observe the kV waveform of the
oscilloscope channel 2.
-If it is not 2V, adjust kV by VR2 on the OP board. After adjustment, set the tube voltage kV to 80KV
by the kV up/down switch.
-Set the kV and the mAs at 80kV and 0.4mAs(30mA).Then observe the mAs, kV waveform of the
oscilloscope channel 1, 2.
26
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
-If it is not about 6V, adjust mA by VR3 on the OP board.
-If it is not about 4V, adjust kV by VR2 on the OP board.
B. Calibration and Confirmation of Tube Current
-Turn off the line switch.
-Lift up the control panel from the unit, and then the PCB OP board appears.
-All DIP switches on the PCB OP board are turned off. (Note: DIP switch is usually in this position.)
-Connect the channel one probe of the oscilloscope to TP5 (IP F/B).
-Connect the channel another one probe of the oscilloscope to TP6 (EP F/B).
Channel 1 is mA, and 35 mA = 7V
Channel 2 is kV, and 40 kV = 2V
-Connect the ground to TP11 (GND).
-Turn on the line switch and the display indicates as follows.
mAs
kV
-Set the kV and the mAs at 40kV and 0.4mAs (35mA). Then observe the mA waveform of the
oscilloscope channel 1.
-If it is not 7V, adjust mA by the calibration data on the OP board.
-Turn off the line switch, and wait until the display switch the light off.
-DIP switch 1 on the PCB OP board is turned on.
-Turn on the line switch and the display indicates as follows.
-Then push the mAs up switch (see operation sheet).
The display indicates as follows.
kV
Calibration code
mAs
Calibration data
C00 is calibration code of tube current (35mA at 40kV~60kV).
179 is calibration data of tube current (35mA at 40kV~60kV).
-Adjust mA by the mAs up/down switch (see operation sheet).
-After it is adjusted, push the store switch (see operation sheet).
-DIP switch 1 on the PCB OP board is turned off then exposure X-ray.
-If it is not 7V, set the calibration data again.
-DIP switch 1 on the PCB OP board is turned on.
-Then push the kV up switch (see operation sheet).
27
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
The display indicates as follows.
mAs
kV
Calibration code
Calibration data
C01 is calibration code of tube current (40mA at 61kV~70kV).
153 is calibration data of tube current (40mA at 61kV~70kV).
-Adjust mA by the mAs up/down switch (see operation sheet).
-After it is adjusted, push the store switch (see operation sheet).
-DIP switch 1 on the PCB OP board is turned off then exposure X-ray.
-If it is not 6V, set the calibration data again.
-Table .1 shows the calibration code and the calibration data against an each tube current.
C. Filament preheat calibration
-This is preheating filament for making tube current.
-The overshoot or the undershoot may occur from the tube current if the preheat calibration data or
the VR3(preheat gain volume) is set by mistake.
-There are two methods to make preheat calibration setting. The calibration data is possible to be
changed in accordance with the tube condition.
-The VR3(preheat gain volume) adjusts the whole range of tube current. Filament preheat
calibration data adjusts each tube current.
-Turn off the line switch.
-Lift up the control panel from the unit, and then the PCB OP Board appears.
-DIP switch 1 on the PCB OP board is turned on.
-Turn on the line switch.
-Push APR switch ① and then the display indicates as follows.
mAs
kV
Preheat calibration code
Preheat calibration data
P00 is Filament preheat calibration code (Preheat calibration code of 60mA).
17 is Filament preheat calibration data (Preheat calibration data of 60mA).
-Adjust data by the mAs up/down switch (see operation sheet).
-After it is adjusted, push the store switch (see operation sheet).
-DIP switch 1 on the PCB OP board is turned off then exposure X-ray.
If overshoot or undershoot occur in the waveform, set the calibration data again.
Then push the kV up switch (see operation sheet).
The display indicates as follows.
28
Product Manual: PXP-40HF
Ltd.
kV
Preheat calibration code
Poskom Co.,
mAs
Preheat calibration data
P01 is Filament preheat calibration code (Preheat calibration code of 40mA).
37 is Filament preheat calibration data (Preheat calibration data of 40mA).
-Adjust data by the mAs up/down switch ⑥ (on the control panel).
-After it is adjusted, push the Store switch ⑨ (on the control panel).
-DIP switch 1 on the PCB OP board is turned off then exposure X-ray.
-If overshoot or undershoot occur in the waveform, set the calibration data again.
-Table. 2 shows the calibration code and the calibration data against an each tube current.
The calibration data is possible to be changed in accordance with the tube condition.
29
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
7. CALIBRATION CODE AND DATA
[Table 1. mA Calibration Data]
AC voltage
Code
Data
Tube voltage
Tube current
mAs
220V
220V
220V
220V
220V
220V
220V
220V
220V
110V
110V
110V
110V
110V
110V
110V
110V
110V
C00
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
C13
C14
C15
C16
C17
179
153
128
153
128
128
102
102
82
179
179
153
133
133
102
102
102
82
40kV ~ 60kV
61kV ~ 70kV
61kV ~ 70kV
71kV ~ 80kV
71kV ~ 80kV
81kV ~ 90kV
81kV ~ 90kV
91kV ~ 100kV
91kV ~ 100kV
40kV ~ 60kV
61kV ~ 70kV
61kV ~ 70kV
71kV ~ 80kV
71kV ~ 80kV
81kV ~ 90kV
81kV ~ 90kV
91kV ~ 100kV
91kV ~ 100kV
35mA
30mA
25mA
30mA
25mA
25mA
20mA
20mA
16mA
35mA
30mA
25mA
30mA
25mA
25mA
20mA
20mA
16mA
0.4 ~ 100
0.4 ~ 64
80 ~ 100
0.4 ~ 32
40 ~80
0.4 ~ 40
50 ~ 80
0.4 ~ 50
64 ~ 80
0.4 ~ 100
0.4 ~ 64
80 ~ 100
0.4 ~ 32
40 ~80
0.4 ~ 40
50 ~ 80
0.4 ~ 50
64 ~ 80
[Table 2. Filament Preheat Calibration Code and Data]
AC voltage
Code
Data
Tube current
220V
220V
220V
220V
220V
110V
110V
110V
110V
110V
P00
P01
P02
P03
P04
P05
P06
P07
P08
P09
17
25
45
70
84
15
38
50
73
89
35mA
30mA
25mA
20mA
16mA
35mA
30mA
25mA
20mA
16mA
30
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
8. ERROR CODE & COUNTERMEASURE
[Table 3. Code & Measures]
Error Code
Err. 07
Err. 08
Err. 10
Err. 11
Err. 12
Err. 14
Err. 15
Err. 16
Err. 17
Err. 19
Err. 21
Content
Action
When the line switch is turned on, this is inspected.
The ready contactor of the hand switch is closed even it
is not pushed.
When the line switch is turned on, this is inspected.
The x-ray contactor of the hand switch is closed even it
is not pushed.
It is displayed when the FIL FB signal is not detected in
the state of standby.
It is displayed when the EP FB signal is not detected in
the state of standby.
It is displayed when the IP FB signal is not detected in
the state of standby.
It is displayed when the FIL FB signal is not detected in
the state of ready.
It is displayed when the EP FB signal is low in the state
of exposure.
It is displayed when the IP FB signal is low in the state
of exposure.
It is displayed when the IP FB and EP FB signal is high
in the state of exposure.
It is displayed when the mAs is over in the state of
exposure.
It is displayed when the connector CON6 on the main
board is not insert.
31
Change the hand switch
Change the hand switch
Replace operation board or
Replace HV tank
Replace operation board or
Replace HV tank
Replace operation board or
Replace HV tank
Replace main board or
Replace power board
Replace operation board
Replace main board or
Replace power board
Replace main board or
replace power board
Check the IP FB level and adjust
it
Replace operation board
Check CON3
9. SCHEMATICS
TD62304
+5V
SEG08_OUT1
(1M-6)
LED4 WAIT
2
1
RED
LED5 M1
2
LED10 M6
2
LED11 M7
2
LED12 M8
2
LED13 ERROR
2
1
RED
1
GREEN
1
GREEN
LED6 M2
2
uD_SR105K
1
GREEN
LED7 M3
2
5
9
1
2
4
6
10
DP
G
F
E
D
C
7
CC
CC
SEG5
3
8
SEG4
B
A
10
9
1
2
4
5
DP
G
F
E
D
7
6
C
B
CC
CC
A
10
9
1
2
4
6
7
5
DP
G
F
E
D
C
B
CC
CC
uD_SR105K
LED3 X-RAY
2
1
YELLOW
1
GREEN
A
5
10
9
1
2
4
6
SEG3
3
8
uD_SR105K
LED2 READY
2
1
GREEN
1
GREEN
DP
G
F
E
D
C
7
CC
CC
SEG2
3
8
uD_SR105K
3
8
SEG1
B
A
10
9
1
2
4
6
7
5
DP
G
F
E
D
C
B
5
CC
CC
A
A
10
2
9
R28
15 1/4W
1
G
2
1
R27
15 1/4W
1
F
2
2
R26
15 1/4W
1
E
2
4
2
R25
15 1/4W
1
D
2
R24
15 1/4W
1
3
8
Q1
Q2
Q3
Q4
Q5
Q6
Q7
VCC
6
2
R23
15 1/4W
1
DP
I1
I2
I3
I4
I5
I6
I7
GND
16
15
14
13
12
11
10
9
3
8
SEG01_OUT
SEG02_OUT
SEG03_OUT
SEG04_OUT
SEG05_OUT
SEG06_OUT
SEG07_OUT
1
2
3
4
5
6
7
8
CC
CC
U8
(1B-13)
(1B-13)
(1B-12)
(1B-12)
(1B-12)
(1B-12)
(1B-12)
C
2
R22
15 1/4W
1
7
R21
15 1/4W
1
(2F-5)
(2G-5)
(2H-5)
(2J-5)
(2K-5)
(2L-5)
(2N-5)
(2O-5)
B
SEG_A
SEG_B
SEG_C
SEG_D
SEG_E
SEG_F
SEG_G
SEG_DP
uD_SR105K
LED8 M4
2
1
GREEN
1
GREEN
SEG6
uD_SR105K
LED9 M5
2
1
GREEN
LED14 REVERSE
2
1
GREEN
APPROVED BY
DESIGNED BY
HTP-24 PORTABLE X-RAY
CONTROL BOARD OP PANEL & HT CONT.
CHECKED BY
DATE
Size
A3
FSCM NO.
<Cage Code>
DWG NO
Rev
0
HTP24-CTL-001
Sheet
3
of
7
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
1
+5V
RA7
2
3
4
5
4.7K
CON6
ISO_PWR
(1B-10),(7G-13)
(1B-10),(5N-13)
2
3
/FAULT
IP_FB_IN
R29
270
ISO_GND
2
1
35312-0310
2
1
D33
1N4148
PC1
8
2
7
3
6
4
5
(1B-10)
HS_READY
1
1
CON1
1
2
3
4
(1B-9)
2
1
35312-0410
2
R30
270
D34
1N4148
HS_X-RAY
1
TLP620-2
+5V
D36
D35
CON2
1
1 2
2
1N4148
2
1
1N4148
(1M-7)
/LASER
35312-0210
APPROVED BY
DESIGNED BY
HTP-24 PORTABLE X-RAY
CONTROL BOARD OP PANEL & HT CONT.
CHECKED BY
DATE
Size
A3
FSCM NO.
<Cage Code>
DWG NO
Rev
HTP24-CTL-001
0
Sheet
4
33
of
7
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
(7B-13)
IP_FB
R31
10K 1%
(1J-5)
IP_FB_ADC
R32
+12V
2
10K 1%
1
R33
1
14
1
39K
3
12
4
C62
1N4148
1
-12V
1SC
CPI
COM
+VS
-VS
FOUT
VOUT
5
10
11
BOX332
2
7
13
(1B-10),(4J-11)
IP_FB_IN
VFC32
MN104
1
1
C22
+IN
-IN
+12V
VR1
10K
2
8
2
D38
+
R35
1/2W 200
C21
1
U10
2
1
2
3
+
2
R34 4.7k
LM358
-
1N4148
40mA(0 ~ 8V)
U9A
4
D37
C24
1
6.8uF/16V tantal
BOX103
2
CON3
1
IP_FB(+)
2
3
EP_FB(+)
C60
2
39P
1
4
R75
5
100K 1%
35312-0510
(1A-10)
(6B-14),(7B-11)
/HT_CHECK
+12V
2
8
D39
1N4148
100KV(0 ~ -5V)
1
1N4148
C58
2
R76
1K
1K
(1J-5)
EP_FB_ADC
R84
R
U9B
MN104
1
1
1
2
BOX223 BOX223
1
1
R36
7
4
D40
BOX223
LM358
2
C27
+
6
2
2
2
2
C26
5
100K 1%
1
R37
C25
EP_FB
+12V C28 MN104
1
2
-12V
C63
VR2
MN104
2
1
-12V
2K
1
R38
10K 1%
3
1
C29
2
C30
2
TP3
MN104
2
MN101
1
TP4
EP_REF
1
+12V
C31
1
2
MN101
1
EP_REF
IP_CONT
U11A
LM358
MN104
2
R42
10M
6
U11B
C33
MN101
+
7
(6C-5)
IP_REF
LM358
R44
10K 1%
2
2
2
-12V
8
1
C59
1
1
-
5
2
2
1
R43
10K 1%
R40
10K 1%
1
(1F-7)
4
BOX224
(6B-14)
1
1
1
2
2
+
1
1
C32
R41
10M
IP_REF
8
3
2
4
R39
10K 1%
1
(1F-7)
2
EP_CONT
APPROVED BY
DESIGNED BY
HTP-24 PORTABLE X-RAY
CONTROL BOARD OP PANEL & HT CONT.
CHECKED BY
DATE
Size
A3
FSCM NO.
<Cage Code>
DWG NO
Rev
0
HTP24-CTL-001
Sheet
5
34
of
7
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
+12V
+12V
R45
5.6K
U12
1
(5J-9),(7B-11)
(5F-4)
1
2
1
1
EP_FB
EP_REF
2
R46
5.6K
1
2
2
1
2
1
2
C36
3
C34
BOX682
2
BOX102
C1
E1
12
R47
1
910
R50
1
910
CON4
2
1
2
EP_CONT1
8
9
2
3
4
EP_CONT2
1
C37 BOX102
2
R51
6.2K 1%
2
1
VCC
-IN1
F.B.
R49
680
R48
470K
+IN1
5
CT
6
C2
E2
11
10
FIL_CONT1
FIL_CONT2
RT
4
5
6
DT
7
15
16
GND
-IN2
+IN2
VR
OC
7
8
LAMP_CONT
14
13
FIL_FB
9
10
C38
/100V_SEL
R52
47K
+
11
1uF/25V TANTAL
2
1
35312-1110
2
U13A
14066
1
1
TL494
(6B-7)
1
2
2
13
R53
2K
(1M-6)
/HV_ON
VR3
2K
R54
750
1
R56
10K 1%
R55
15K
2 1
3 1
1
2
(1J-5)
FIL_FB_ADC
2
2
2
+5V
R57
10K 1%
1
-12V
1
2
3
C39
R62
BOX473 470K
1
1
R63
10K
+12V
1
2
2
2
R82 10K
2
3
U17
1PN2222
1
1
C42 BOX102
2
R64
5K 1%
R81
1
3.3K
1
2
1
R79 5.6K
1
5
6
4
7
15
16
2
R70 470K
2
2
-IN1
VCC
C1
E1
8
9
10
R58
1K
F.B.
12
1
2
R61
5.6K
1K
+IN1
2
C41
MN104
1
2
2
CT
C2
E2
11
10
RT
DT
GND
-IN2
+IN2
1
1
1
2
12
1
2
1
R80
2
PN2222 DRV1
1
2
R65
1K
VR
OC
14
13
2
C40
BOX104
7
1
3
2
2
R66
1K
/LAMP_ON
(1M-6)
1
TL494
R78 30K
(5L-4)
IP_REF
1
IP_FB
C61 BOX104
2
1
1
R77 5.6K
U13C
14066
R67
47K
1
3
2
4
C43
BOX473
2
(6K-11) 1
11
U15
1
+
R68
2K
APPROVED BY
2
5
FIL_FB
U13B
14066
+12V
R59
5.6K
OP07
6
2
4
8
U14
-
2
R60
4.7K
/PREP
DESIGNED BY
HTP-24 PORTABLE X-RAY
(1M-6)
CONTROL BOARD OP PANEL & HT CONT.
CHECKED BY
DATE
Size
A3
FSCM NO.
<Cage Code>
DWG NO
Rev
0
HTP24-CTL-001
Sheet
6
35
of
7
Product Manual: PXP-40HF
Ltd.
Poskom Co.,
+12V
+12V
TP5
2
+12V
C44
1
R85
100k
MN104
U16A
1
8
64K
3
(5I-15)
1
2
2
R86
100k
+
1
LM393
1
R71
100K
4
IP_FB
2
IP_FB
1
R69
2
C45
BOX473
TP6
(1B-10),(4J-11)
/FAULT
TD62304AP
14066
1
1
C49
MN104
C50
MN104
2
C51
MN104
2
C48
MN104
2
2
TD62304AP
1
27512
C47
MN104
2
74HC573
4
1
LM393
100K
1
1
-
C46
BOX103
R74
+ C23
R73 + C35
10u/16V 56K
10u/16V
+5V
1
6
2
7
2
1
(5J-9),(6B-14)
R72
100K
2
2
EP_FB
U16B
+
1
5
8
1
EP_FB
TP7
+5V
1
+5V
H8
H7
H6
H5
H4
H3
H2
H1
H11
H10
H9
H12
1
1
TP8
HOLE
1
1
1
1
1
1
1
1
1
HOLE
HOLE
HOLE
2
2
HOLE
HOLE
HOLE
HOLE
HOLE
HOLE
HOLE
HOLE
1
DGND
1
C53
100uF/50V
1
+
1
C52
MN104
TP9
CON5
1
2
3
4
5
1
+12V
TP11
1
1
TP10
AGND
1
2
1
AGND
1
2
C55
MN104
1
C54
+
100uF/50V
TP12
C57
MN104
2
C56
+
100uF/50V
-12V
1
2
35312-0510
+12V
APPROVED BY
-12V
DESIGNED BY
HTP-24 PORTABLE X-RAY
CONTROL BOARD OP PANEL & HT CONT.
CHECKED BY
DATE
Size
A3
FSCM NO.
<Cage Code>
DWG NO
Rev
HTP24-CTL-001
0
Sheet
7
36
of
7
Poskom Co.,
C9
1500/200V
+
C10
1500/200V
102/AC250V
C17
+
R12 NTC10D22
C15
1500/200V
BD1
D25XB60
+
C16
1500/200V
R9
G2
K2
D4
D10LC40U
F1
R13
10K
3
L1
1
1
TB1
R5
2W 10
G3A
K3A
C14
102/1KV
R10
2W 10
2
Q8
68K 1W
BTA26-600
Q11
3
3
3
Q7
FQL40N5
2
C4
102/1KV
G4
K4
Q9
FQL40N5
2
D5
D10LC40U
1
HV TRANS NP
TB2
1
2
R11
2W 10
+5V
H : 220V
L : 110V
CN2
1
2
C18
K3
G3
SIG1(+)
100_SEL
100/400V
T1
+
R14 1W100
R15
2W24K
C47
R16
2W 100K
K2
G2
C21
222/1KV
TP1 +5V 0.5A
5
6
LM7805CT
IN
1
+
C24
C46
MN104
C23
100/16V
100/16V
+
Q12
IXIF 16N90Q
1
TC7662A1
PG_S
C28
TT22/16V +
3
R18 220
5
3
4
BOX104
C29
C30
BOX102
BOX472
R20
20K
Z5
R19
3.9K
R22
120
C31
C32
BOX103
BOX102
1N4747
R21
5W 0.2
TP6
HS2
D9 D10LC20U
1
D10
8
7
6
5
1N4937
47/25V
100V_SEL
+12.2V
C35
+
+
C34
2200/16V
R23
1W680
2200/16V
1
+
5
6
S1
S1A
1
2
1
2
3
4
3
4
K4A
G4A
5
6
K1A
G1A
R27 20
Q15
IRF540
+12.2V
D12
1
2
3
4
R28
R25
5.1K
Q18
PN2222
Q16
C1815
Q17
PN2907
R30
NO HEAT SINK
Z6
1N4937
1W1K
20K
+ C40
22/25V
R32 20
1N4746
CON4
53258-4
Q19
IRF540
R33
Z7
Q20
PN2907
C41
M472/100V
D13 1W1K
R34
20K
R31
1%9.3K
R35
3W 0.5/¹«À¯µµ
2
4
3
4
1N4746
+12.2V
100
PC817
3
2
2
C39
10uF/25V
3
4
5
6
M472/100V C37
Q14
PN2222
R24
1/2W470
1
GND
R26
1
2
5
6
K1
G1
R41
47K
1
U5
1
2
+12.2V
12
+
S4A
K2A
G2A
+5V
6
OUT
S4
SIG2(+)
TP7 +12.2V 6A
+12V
1
+
C33
2200/16V(13pie)
K4
G4
35312-11
5
U4
78L05
TP5
-12V 20mA
10
+ C36
C38
100uF/25V
1
2
3
4
C25
C26
100/16V TT22/16V
+
U3
PG
IN
3
4
5
6
1
2
3
4
5
CON2
35312-5
CON3
1
2
3
4
5
FIL_CONT
6
7
LAMP_CONT
8
9
FIL_FB
10
11
8
1
6
TP4
1
2
7
R17 4.7
8
3
MN104
+5V
GND
+12.2V
GND
-12V
+
+
UC3844
1
TG
3
HS1
2
D11 1N4937
C45
HS3
C22
470/25V
NP
GND
OUT
2
R29
27K
3
4
5
6
1
1
1
U2
S2L60
7
3
C2235
1
2
SIG2(-)
D7
1N4937
GND
TP2
1
2
K3A
G3A
TP3
+5V
D8
C27
3
4
S2A
D6 1N4937
C20 47/25V
2
4
U7
3
4
S2
R40
10K
PQ32/30
1
C19
M104/100V
C48
22/25V
1
2
5
6
100V SELECTION
D14
1N4937
Q21
1
2
SIG1(-)
L3
SQE20
1/400V
S3A
S3
FQL40N5
Q10
G4A
K4A
G2A
K2A
10TURNS
FET GATE DRIVE CIRCUIT
FQL40N5
50T2A
C6
PP105/400V
C11
102/1KV
3
-
C12
G1A
K1A
+
SNUBER
1
C13
+
3
C8
102/AC250V
L2
1/2W470K
R8
R6
2W 10
3
R7
2
Q6
FQL40N5
D3
D10LC40U
2
1
68K 1W
Q5
FQL40N5
PP105/400V
C5
G3
102/1KV C7
K3
1
G1
K1
SNUBER
1
5
4
3
2
1
224/AC250V
SC-10-D050
Q4
FQL40N5
D2
D10LC40U
2
1
224/AC250V
Q3
FQL40N5
2
3
53258-05
CON1
CN1
100V/SW
1
2
1
Product Manual: PXP-40HF
Ltd.
1N4937
1
TH
3
C42
101/3KV
R37 4.7K
1
R36
5D11
C43
MN104
R38 10K
ISO_GND
DESIGNED BY
HTP24 PWR & DRV
222/AC250V
COLIMETER
2
1
3
2
1
APPROVED BY
R39
1%2.4K
C44
HAND SW PWR
50N60
2
ISO_5V
HS4
Q13
t
2
U6
TL431
CON5
CON6
35312-3
53258-2
CHECKED BY
DATE
Size
A3
FSCM NO.
DWG NO
Rev
00
HTP24-PWR-001
<Cage Code>
Sheet
1
37
of
1
Download