aim bsc w chg 1 2 dtd 5-19-22

June 17, 2021 U.S. Department of Transportation Federal Aviation Administration Aeronautical Information Manual Official Guide to Basic Flight Information and ATC Procedures An electronic version of this publication is available online at http://www.faa.gov/air_traffic/publications AIM Record of Changes Change Number Change Filed Comments U.S. Department of Transportation Federal Aviation Administration AERONAUTICAL INFORMATION MANUAL Change 2 May 19, 2022 DO NOT DESTROY BASIC DATED JUNE 17, 2021 AIM 5/19/22 Aeronautical Information Manual Explanation of Changes Effective: May 19, 2022 a. 1−1−13. USER REPORTS REQUESTED ON NAVAID OUTAGES inserted and other tables in the chapter renumbered along with a new sentence to reference the table. The current publication of the AIM contains a duplication of content in paragraph 1−1−13. This change deletes the duplicated section found in paragraph 1−1−13, subparagraph a. e. 7−1−12. ATC INFLIGHT WEATHER AVOIDANCE ASSISTANCE b. 2−2−4. LED LIGHTING SYSTEMS This change adds a new paragraph providing information and clarity in order to emphasize the importance of incorporating procedures—for the avoidance of obstacles marked with light−emitting diode (LED) obstruction lights during night vision goggles (NVG) operations—into manuals and/or standard operating procedures (SOP). c. 5−4−5. INSTRUMENT APPROACH PROCEDURE (IAP) CHARTS FAA Order 8260.46 is updated to reflect adding minimum safe altitudes (MSAs) to graphic departures. This AIM change reflects the new terminal instrument procedures (TERPS) guidance. d. 7−1−2. FAA WEATHER SERVICES This change adds a new table for SPECI issuance including snow−related intensity changes so flight crews can accurately assess holdover time limitations. TBL 7−1−1 in Chapter 7, Section 1, was Explanation of Changes This change adds the word “lateral” to this paragraph to align with FAA Order JO 7110.65 and the Aeronautical Information Publication (AIP). f. 7−6−2. REPORTING RADIO/RADAR ALTIMETER ANOMALIES This change adds a new paragraph to address the issue of radio frequency interference (RFI) in the C−band that could cause erroneous radio altimeter values and impact dependent system functions due to the deployment of 5G antennas. g. Editorial Changes Editorial changes include the replacement of filing code M2 for M3 in paragraph 5−1−6 and various tables in Appendix 4, correcting the spelling of Harrisburg International Airport in the title of FIG 5−4−12, and updating a hyperlink in subparagraph 4−7−1e. h. Entire Publication Additional editorial/format changes were made where necessary. Revision bars were not used because of the insignificant nature of these changes. E of Chg−1 5/19/22 AIM AIM Change 2 Page Control Chart May 19, 2022 REMOVE PAGES DATED INSERT PAGES Checklist of Pages CK−1 through CK−7 . . . . Table of Contents i through xii . . . . . . . . . . . 1−1−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−18 and 1−1−19 . . . . . . . . . . . . . . . . . . . . 1−1−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−21 and 1−1−22 . . . . . . . . . . . . . . . . . . . . 1−1−23 through 1−1−39 . . . . . . . . . . . . . . . . . 2−2−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−2−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−7−1 and 4−7−2 . . . . . . . . . . . . . . . . . . . . . . 5−1−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−1−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−2 through 7−1−7 . . . . . . . . . . . . . . . . . . . 7−1−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−9 through 7−1−16 . . . . . . . . . . . . . . . . . . 7−1−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−18 and 7−1−19 . . . . . . . . . . . . . . . . . . . . 7−1−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−21 through 7−1−36 . . . . . . . . . . . . . . . . . 7−1−37 and 7−1−38 . . . . . . . . . . . . . . . . . . . . 7−1−39 through 7−1−49 . . . . . . . . . . . . . . . . . 7−1−50 and 7−1−51 . . . . . . . . . . . . . . . . . . . . 7−1−52 and 7−1−53 . . . . . . . . . . . . . . . . . . . . 7−1−54 through 7−1−58 . . . . . . . . . . . . . . . . . 7−1−59 through 7−1−70 . . . . . . . . . . . . . . . . . 7−6−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−2 through 7−6−9 . . . . . . . . . . . . . . . . . . . 7−6−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−11 through 7−6−14 . . . . . . . . . . . . . . . . . 7−6−15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 4−9 . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 4−10 . . . . . . . . . . . . . . . . . . . . . . . . Appendix 4−13 and Appendix 4−14 . . . . . . . PCG−1 and PCG−2 . . . . . . . . . . . . . . . . . . . . PCG A−1 through PCG A−17 . . . . . . . . . . . . 12/2/21 12/2/21 6/17/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 6/17/21 6/17/21 12/2/21 12/2/21 6/17/21 6/17/21 12/2/21 6/17/21 6/17/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 12/2/21 12/2/21 12/2/21 12/2/21 12/2/21 Checklist of Pages CK−1 through CK−7 . . . . Table of Contents i through xii . . . . . . . . . . . 1−1−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−18 and 1−1−19 . . . . . . . . . . . . . . . . . . . . 1−1−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−21 and 1−1−22 . . . . . . . . . . . . . . . . . . . . 1−1−23 through 1−1−39 . . . . . . . . . . . . . . . . . 2−2−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−2−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−7−1 and 4−7−2 . . . . . . . . . . . . . . . . . . . . . . 5−1−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−1−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−2 through 7−1−7 . . . . . . . . . . . . . . . . . . . 7−1−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−9 through 7−1−16 . . . . . . . . . . . . . . . . . . 7−1−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−18 and 7−1−19 . . . . . . . . . . . . . . . . . . . . 7−1−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−21 through 7−1−36 . . . . . . . . . . . . . . . . . 7−1−37 and 7−1−38 . . . . . . . . . . . . . . . . . . . . 7−1−39 through 7−1−49 . . . . . . . . . . . . . . . . . 7−1−50 and 7−1−51 . . . . . . . . . . . . . . . . . . . . 7−1−52 and 7−1−53 . . . . . . . . . . . . . . . . . . . . 7−1−54 through 7−1−58 . . . . . . . . . . . . . . . . . 7−1−59 through 7−1−71 . . . . . . . . . . . . . . . . . 7−6−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−2 through 7−6−9 . . . . . . . . . . . . . . . . . . . 7−6−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−11 through 7−6−14 . . . . . . . . . . . . . . . . . 7−6−15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 4−9 . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 4−10 . . . . . . . . . . . . . . . . . . . . . . . . Appendix 4−13 and Appendix 4−14 . . . . . . . PCG−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG A−1 through PCG A−17 . . . . . . . . . . . . Page Control Chart DATED 5/19/22 5/19/22 6/17/21 5/19/22 5/19/22 5/19/22 5/19/22 6/17/21 5/19/22 5/19/22 12/2/21 5/19/22 6/17/21 5/19/22 12/2/21 5/19/22 6/17/21 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 5/19/22 12/2/21 5/19/22 5/19/22 5/19/22 5/19/22 i 5/19/22 AIM PCG C−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG C−4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG D−1 through PCG D−4 . . . . . . . . . . . . . PCG E−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG E−2 and PCG E−3 . . . . . . . . . . . . . . . . . PCG H−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG H−2 and PCG H−3 . . . . . . . . . . . . . . . . PCG M−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG M−4 through PCG M−6 . . . . . . . . . . . . PCG O−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG O−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG P−3 through PCG P−6 . . . . . . . . . . . . . . PCG S−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG S−8 through PCG S−10 . . . . . . . . . . . . . PCG T−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG T−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index I−1 through I−13 . . . . . . . . . . . . . . . . . ii 12/2/21 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 12/2/21 PCG C−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG C−4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG D−1 through PCG D−4 . . . . . . . . . . . . . PCG E−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG E−2 and PCG E−3 . . . . . . . . . . . . . . . . . PCG H−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG H−2 and PCG H−3 . . . . . . . . . . . . . . . . PCG M−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG M−4 through PCG M−6 . . . . . . . . . . . . PCG O−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG O−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG P−3 through PCG P−5 . . . . . . . . . . . . . . PCG S−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG S−8 through PCG S−10 . . . . . . . . . . . . . PCG T−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG T−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index I−1 through I−13 . . . . . . . . . . . . . . . . . 5/19/22 12/2/21 5/19/22 5/19/22 5/19/22 6/17/21 5/19/22 6/17/21 5/19/22 5/19/22 5/19/22 5/19/22 6/17/21 5/19/22 5/19/22 12/2/21 5/19/22 Page Control Chart 5/19/22 AIM Checklist of Pages PAGE DATE PAGE DATE PAGE DATE Chapter 2. Aeronautical Lighting and Other Airport Visual Aids Section 1. Airport Lighting Aids Cover 6/17/21 1−1−12 12/2/21 Record of Changes N/A 1−1−13 12/2/21 Exp of Chg−1 5/19/22 1−1−14 12/2/21 1−1−15 12/2/21 1−1−16 12/2/21 1−1−17 6/17/21 2−1−1 12/2/21 1−1−18 5/19/22 2−1−2 6/17/21 5/19/22 1−1−19 5/19/22 2−1−3 6/17/21 5/19/22 1−1−20 5/19/22 2−1−4 6/17/21 5/19/22 1−1−21 5/19/22 2−1−5 6/17/21 5/19/22 1−1−22 5/19/22 2−1−6 6/17/21 5/19/22 1−1−23 5/19/22 2−1−7 6/17/21 CK−6 5/19/22 1−1−24 5/19/22 2−1−8 6/17/21 CK−7 5/19/22 1−1−25 5/19/22 2−1−9 6/17/21 1−1−26 5/19/22 2−1−10 6/17/21 6/17/21 1−1−27 5/19/22 2−1−11 6/17/21 6/17/21 1−1−28 5/19/22 2−1−12 6/17/21 6/17/21 1−1−29 5/19/22 2−1−13 6/17/21 Publication Policy 6/17/21 1−1−30 5/19/22 Reg & Advis Cir 6/17/21 1−1−31 5/19/22 1−1−32 5/19/22 1−1−33 5/19/22 2−2−1 6/17/21 1−1−34 5/19/22 2−2−2 5/19/22 1−1−35 5/19/22 1−1−36 5/19/22 1−1−37 5/19/22 1−1−38 5/19/22 2−3−1 6/17/21 1−1−39 5/19/22 2−3−2 6/17/21 5/19/22 2−3−3 6/17/21 5/19/22 2−3−4 6/17/21 5/19/22 2−3−5 6/17/21 2−3−6 6/17/21 2−3−7 6/17/21 2−3−8 6/17/21 Checklist of Pages CK−1 CK−2 CK−3 CK−4 CK−5 Subscription Info Comments/Corr Basic Flight Info Table of Contents i 5/19/22 ii 5/19/22 iii 5/19/22 iv 5/19/22 v 5/19/22 vi 5/19/22 vii viii ix x xi xii 5/19/22 5/19/22 5/19/22 Chapter 1. Air Navigation Section 1. Navigation Aids Section 2. Performance−Based Navigation (PBN) and Area Navigation (RNAV) Section 2. Air Navigation and Obstruction Lighting Section 3. Airport Marking Aids and Signs 1−2−1 6/17/21 2−3−9 6/17/21 1−2−2 6/17/21 2−3−10 6/17/21 1−2−3 6/17/21 2−3−11 6/17/21 1−2−4 6/17/21 2−3−12 6/17/21 1−1−1 6/17/21 1−2−5 12/2/21 1−1−2 6/17/21 2−3−13 6/17/21 1−2−6 6/17/21 1−1−3 6/17/21 2−3−14 6/17/21 1−2−7 6/17/21 1−1−4 6/17/21 2−3−15 6/17/21 1−2−8 12/2/21 1−1−5 6/17/21 2−3−16 6/17/21 1−2−9 6/17/21 1−1−6 12/2/21 2−3−17 6/17/21 1−2−10 6/17/21 1−1−7 6/17/21 2−3−18 6/17/21 1−1−8 6/17/21 2−3−19 6/17/21 1−1−9 6/17/21 2−3−20 6/17/21 1−1−10 12/2/21 2−3−21 6/17/21 1−1−11 12/2/21 2−3−22 6/17/21 Checklist of Pages CK−1 AIM 5/19/22 Checklist of Pages PAGE DATE 2−3−23 6/17/21 2−3−24 6/17/21 2−3−25 6/17/21 2−3−26 6/17/21 2−3−27 PAGE DATE PAGE DATE 4−3−11 6/17/21 4−3−12 6/17/21 4−3−13 12/2/21 4−3−14 6/17/21 6/17/21 4−3−15 6/17/21 2−3−28 6/17/21 12/2/21 4−3−16 6/17/21 2−3−29 6/17/21 4−1−2 12/2/21 4−3−17 6/17/21 2−3−30 6/17/21 4−1−3 6/17/21 4−3−18 6/17/21 2−3−31 6/17/21 4−1−4 6/17/21 4−3−19 6/17/21 6/17/21 4−3−20 6/17/21 6/17/21 4−3−21 6/17/21 6/17/21 4−3−22 6/17/21 12/2/21 4−3−23 12/2/21 6/17/21 4−3−24 12/2/21 12/2/21 Chapter 3. Airspace Section 1. General Chapter 4. Air Traffic Control Section 1. Services Available to Pilots 4−1−1 4−1−5 4−1−6 4−1−7 3−1−1 6/17/21 4−1−8 3−1−2 6/17/21 4−1−9 3−1−3 6/17/21 4−1−10 6/17/21 4−3−25 Section 2. Controlled Airspace 4−1−11 6/17/21 4−3−26 12/2/21 4−1−12 12/2/21 4−3−27 12/2/21 6/17/21 4−3−28 12/2/21 6/17/21 4−3−29 12/2/21 6/17/21 4−3−30 12/2/21 6/17/21 4−3−31 12/2/21 4−3−32 12/2/21 3−2−1 6/17/21 4−1−13 3−2−2 6/17/21 4−1−14 3−2−3 6/17/21 4−1−15 3−2−4 6/17/21 4−1−16 3−2−5 6/17/21 4−1−17 12/2/21 3−2−6 6/17/21 4−1−18 12/2/21 3−2−7 6/17/21 4−1−19 12/2/21 3−2−8 6/17/21 3−2−9 6/17/21 3−2−10 6/17/21 Section 3. Class G Airspace 3−3−1 6/17/21 Section 4. Special Use Airspace 3−4−1 12/2/21 3−4−2 6/17/21 3−4−3 6/17/21 Section 5. Other Airspace Areas 3−5−1 6/17/21 3−5−2 6/17/21 3−5−3 6/17/21 3−5−4 6/17/21 3−5−5 6/17/21 3−5−6 6/17/21 3−5−7 6/17/21 3−5−8 6/17/21 3−5−9 6/17/21 3−5−10 12/2/21 CK−2 Section 4. ATC Clearances and Aircraft Separation 4−4−1 6/17/21 4−4−2 6/17/21 4−4−3 6/17/21 6/17/21 4−4−4 6/17/21 4−2−2 6/17/21 4−4−5 12/2/21 4−2−3 6/17/21 4−4−6 6/17/21 4−2−4 12/2/21 4−4−7 6/17/21 4−2−5 12/2/21 4−4−8 6/17/21 4−2−6 12/2/21 4−4−9 6/17/21 4−2−7 12/2/21 4−4−10 6/17/21 4−2−8 12/2/21 4−4−11 6/17/21 4−4−12 6/17/21 Section 2. Radio Communications Phraseology and Techniques 4−2−1 Section 3. Airport Operations Section 5. Surveillance Systems 4−3−1 6/17/21 4−3−2 6/17/21 4−3−3 6/17/21 4−5−1 6/17/21 6/17/21 4−5−2 6/17/21 6/17/21 4−5−3 6/17/21 6/17/21 4−5−4 6/17/21 4−3−7 6/17/21 4−5−5 6/17/21 4−3−8 6/17/21 4−5−6 6/17/21 4−3−9 6/17/21 4−5−7 6/17/21 4−3−10 6/17/21 4−5−8 12/2/21 4−5−9 6/17/21 4−3−4 4−3−5 4−3−6 Checklist of Pages 5/19/22 AIM Checklist of Pages PAGE DATE PAGE DATE 6/17/21 5−1−9 12/2/21 5−3−21 6/17/21 6/17/21 5−1−10 5/19/22 5−3−22 6/17/21 4−5−12 6/17/21 5−1−11 12/2/21 5−3−23 6/17/21 4−5−13 6/17/21 5−1−12 12/2/21 5−3−24 6/17/21 4−5−14 6/17/21 5−1−13 12/2/21 5−3−25 6/17/21 12/2/21 5−3−26 6/17/21 6/17/21 6/17/21 PAGE DATE 4−5−10 4−5−11 4−5−15 6/17/21 5−1−14 4−5−16 6/17/21 5−1−15 12/2/21 5−3−27 4−5−17 6/17/21 5−1−16 12/2/21 5−3−28 4−5−18 6/17/21 5−1−17 12/2/21 4−5−19 6/17/21 5−1−18 12/2/21 4−5−20 12/2/21 4−5−21 6/17/21 4−5−22 6/17/21 Section 6. Operational Policy/ Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR Section 4. Arrival Procedures 5−4−1 6/17/21 Section 2. Departure Procedures 5−4−2 6/17/21 5−4−3 6/17/21 5−2−1 6/17/21 5−4−4 6/17/21 5−2−2 6/17/21 5−4−5 6/17/21 5−2−3 6/17/21 5−4−6 6/17/21 5−2−4 12/2/21 5−4−7 6/17/21 5−2−5 12/2/21 5−4−8 5/19/22 5−2−6 12/2/21 5−4−9 6/17/21 4−6−1 6/17/21 5−2−7 12/2/21 5−4−10 6/17/21 4−6−2 12/2/21 5−2−8 12/2/21 5−4−11 6/17/21 4−6−3 12/2/21 5−2−9 12/2/21 5−4−12 6/17/21 4−6−4 12/2/21 5−2−10 12/2/21 5−4−13 6/17/21 4−6−5 12/2/21 5−2−11 12/2/21 5−4−14 6/17/21 4−6−6 12/2/21 5−2−12 12/2/21 5−4−15 6/17/21 4−6−7 12/2/21 5−2−13 12/2/21 5−4−16 6/17/21 4−6−8 12/2/21 5−4−17 12/2/21 4−6−9 12/2/21 5−4−18 5/19/22 5−4−19 6/17/21 Section 7. Operational Policy/ Procedures for the Gulf of Mexico 50 NM Lateral Separation Initiative 4−7−1 5/19/22 4−7−2 5/19/22 Chapter 5. Air Traffic Procedures Section 1. Preflight 5−1−1 12/2/21 5−1−2 12/2/21 5−1−3 12/2/21 5−1−4 12/2/21 5−1−5 12/2/21 5−1−6 12/2/21 5−1−7 12/2/21 5−1−8 12/2/21 Checklist of Pages Section 3. En Route Procedures 5−3−1 6/17/21 5−4−20 6/17/21 5−3−2 6/17/21 5−4−21 6/17/21 5−3−3 6/17/21 5−4−22 6/17/21 6/17/21 5−4−23 6/17/21 5−3−5 6/17/21 5−4−24 6/17/21 5−3−6 6/17/21 5−4−25 12/2/21 5−3−7 6/17/21 5−4−26 12/2/21 5−3−8 6/17/21 5−4−27 12/2/21 5−3−9 6/17/21 5−4−28 12/2/21 5−3−10 6/17/21 5−4−29 12/2/21 5−3−11 6/17/21 5−4−30 12/2/21 5−3−12 6/17/21 5−4−31 12/2/21 6/17/21 5−4−32 12/2/21 5−3−14 6/17/21 5−4−33 12/2/21 5−3−15 6/17/21 5−4−34 12/2/21 5−3−16 6/17/21 5−4−35 12/2/21 5−3−17 6/17/21 5−4−36 12/2/21 5−3−18 6/17/21 5−4−37 12/2/21 5−3−19 6/17/21 5−4−38 12/2/21 5−3−20 6/17/21 5−4−39 12/2/21 5−3−4 5−3−13 CK−3 AIM 5/19/22 Checklist of Pages PAGE DATE PAGE DATE 5−4−40 12/2/21 5−6−10 12/2/21 5−4−41 12/2/21 5−6−11 12/2/21 5−4−42 12/2/21 5−6−12 6/17/21 5−4−43 12/2/21 7−1−1 6/17/21 5−6−13 6/17/21 5−4−44 12/2/21 7−1−2 5/19/22 5−6−14 6/17/21 5−4−45 12/2/21 7−1−3 5/19/22 5−4−46 12/2/21 5/19/22 5−4−47 12/2/21 Chapter 6. Emergency Procedures 7−1−4 7−1−5 5/19/22 5−4−48 12/2/21 7−1−6 5/19/22 5−4−49 12/2/21 Section 1. General 7−1−7 5/19/22 5−4−50 12/2/21 7−1−8 5/19/22 5−4−51 12/2/21 7−1−9 5/19/22 5−4−52 12/2/21 7−1−10 5/19/22 5−4−53 12/2/21 7−1−11 5/19/22 5−4−54 12/2/21 6/17/21 7−1−12 5/19/22 5−4−55 12/2/21 6/17/21 7−1−13 5/19/22 5−4−56 12/2/21 6−2−3 6/17/21 7−1−14 5/19/22 5−4−57 12/2/21 6−2−4 6/17/21 7−1−15 5/19/22 5−4−58 12/2/21 6−2−5 6/17/21 7−1−16 5/19/22 5−4−59 12/2/21 6−2−6 6/17/21 7−1−17 5/19/22 5−4−60 12/2/21 6−2−7 6/17/21 7−1−18 5/19/22 5−4−61 12/2/21 6−2−8 6/17/21 7−1−19 5/19/22 5−4−62 12/2/21 6−2−9 6/17/21 7−1−20 5/19/22 5−4−63 12/2/21 6/17/21 7−1−21 5/19/22 6/17/21 7−1−22 5/19/22 7−1−23 5/19/22 7−1−24 5/19/22 7−1−25 5/19/22 6/17/21 7−1−26 5/19/22 6/17/21 7−1−27 5/19/22 6/17/21 7−1−28 5/19/22 6/17/21 7−1−29 5/19/22 6−3−5 6/17/21 7−1−30 5/19/22 6−3−6 6/17/21 7−1−31 5/19/22 6−3−7 6/17/21 7−1−32 5/19/22 7−1−33 5/19/22 7−1−34 5/19/22 7−1−35 5/19/22 6/17/21 7−1−36 5/19/22 6/17/21 7−1−37 5/19/22 7−1−38 5/19/22 7−1−39 5/19/22 7−1−40 5/19/22 7−1−41 5/19/22 7−1−42 5/19/22 7−1−43 5/19/22 7−1−44 5/19/22 7−1−45 5/19/22 12/2/21 7−1−46 5/19/22 12/2/21 7−1−47 5/19/22 Section 5. Pilot/Controller Roles and Responsibilities 5−5−1 12/2/21 5−5−2 12/2/21 5−5−3 12/2/21 5−5−4 12/2/21 5−5−5 12/2/21 5−5−6 12/2/21 5−5−7 12/2/21 5−5−8 12/2/21 5−5−9 12/2/21 6−1−1 Section 2. Emergency Services Available to Pilots 6−2−1 6−2−2 6−2−10 6−2−11 Section 3. Distress and Urgency Procedures 6−3−1 6−3−2 6−3−3 6−3−4 Section 4. Two−way Radio Communications Failure 6−4−1 Section 6. National Security and Interception Procedures 5−6−1 6/17/21 5−6−2 6/17/21 5−6−3 6/17/21 5−6−4 5−6−5 5−6−6 5−6−7 5−6−8 5−6−9 CK−4 6/17/21 6/17/21 12/2/21 12/2/21 6/17/21 6−4−2 Section 5. Aircraft Rescue and Fire Fighting Communications 6−5−1 6/17/21 6−5−2 6/17/21 PAGE DATE Chapter 7. Safety of Flight Section 1. Meteorology Checklist of Pages 5/19/22 AIM Checklist of Pages PAGE DATE PAGE DATE 7−1−48 5/19/22 7−4−6 6/17/21 7−1−49 5/19/22 7−4−7 6/17/21 7−1−50 5/19/22 7−4−8 6/17/21 7−1−51 5/19/22 7−1−52 5/19/22 7−1−53 5/19/22 7−1−54 5/19/22 Section 5. Bird Hazards and Flight Over National Refuges, Parks, and Forests PAGE DATE Chapter 9. Aeronautical Charts and Related Publications Section 1. Types of Charts Available 9−1−1 12/2/21 9−1−2 12/2/21 7−1−55 5/19/22 7−5−1 7−1−56 5/19/22 7−5−2 7−1−57 5/19/22 7−1−58 5/19/22 7−1−59 5/19/22 7−1−60 5/19/22 7−6−1 5/19/22 9−1−8 6/17/21 7−1−61 5/19/22 7−6−2 5/19/22 9−1−9 12/2/21 7−1−62 5/19/22 7−6−3 5/19/22 9−1−10 6/17/21 7−1−63 5/19/22 7−6−4 5/19/22 9−1−11 12/2/21 7−1−64 5/19/22 7−6−5 5/19/22 9−1−12 6/17/21 7−1−65 5/19/22 7−6−6 5/19/22 9−1−13 6/17/21 7−1−66 5/19/22 7−6−7 5/19/22 7−1−67 5/19/22 7−6−8 5/19/22 7−1−68 5/19/22 7−6−9 5/19/22 7−1−69 5/19/22 7−6−10 5/19/22 7−1−70 5/19/22 7−6−11 5/19/22 7−1−71 5/19/22 7−6−12 5/19/22 10−1−1 12/2/21 7−6−13 5/19/22 10−1−2 12/2/21 7−6−14 5/19/22 10−1−3 12/2/21 7−6−15 5/19/22 10−1−4 12/2/21 10−1−5 12/2/21 10−1−6 12/2/21 10−1−7 12/2/21 Section 2. Barometric Altimeter Errors and Setting Procedures 7−2−1 6/17/21 7−2−2 6/17/21 7−2−3 6/17/21 Section 3. Cold Temperature Barometric Altimeter Errors, Setting Procedures and Cold Temperature Airports (CTA) 7−3−1 6/17/21 7−3−2 6/17/21 7−3−3 6/17/21 7−3−4 6/17/21 7−3−5 6/17/21 7−3−6 12/2/21 7−3−7 6/17/21 Section 4. Wake Turbulence 7−4−1 6/17/21 7−4−2 6/17/21 7−4−3 6/17/21 7−4−4 6/17/21 7−4−5 6/17/21 Checklist of Pages 6/17/21 9−1−3 12/2/21 6/17/21 9−1−4 12/2/21 9−1−5 6/17/21 9−1−6 6/17/21 9−1−7 12/2/21 Section 6. Potential Flight Hazards Section 7. Safety, Accident, and Hazard Reports 7−7−1 6/17/21 7−7−2 6/17/21 7−7−3 6/17/21 Chapter 8. Medical Facts for Pilots Section 1. Fitness for Flight Chapter 10. Helicopter Operations Section 1. Helicopter IFR Operations Section 2. Special Operations 10−2−1 6/17/21 10−2−2 12/2/21 10−2−3 12/2/21 10−2−4 6/17/21 10−2−5 6/17/21 10−2−6 6/17/21 8−1−1 6/17/21 10−2−7 6/17/21 8−1−2 6/17/21 10−2−8 6/17/21 8−1−3 6/17/21 10−2−9 6/17/21 8−1−4 6/17/21 10−2−10 6/17/21 8−1−5 6/17/21 10−2−11 6/17/21 8−1−6 6/17/21 10−2−12 6/17/21 8−1−7 6/17/21 10−2−13 6/17/21 8−1−8 6/17/21 10−2−14 6/17/21 8−1−9 6/17/21 10−2−15 6/17/21 10−2−16 6/17/21 10−2−17 6/17/21 CK−5 AIM 5/19/22 Checklist of Pages PAGE DATE Appendices PAGE DATE PAGE DATE PCG A−11 5/19/22 PCG M−1 6/17/21 Appendix 1−1 6/17/21 PCG A−13 5/19/22 PCG M−2 12/2/21 Env N/A PCG A−12 5/19/22 PCG M−3 12/2/21 Appendix 2−1 6/17/21 PCG A−14 5/19/22 PCG M−4 5/19/22 Appendix 3−1 6/17/21 PCG A−15 5/19/22 PCG M−5 5/19/22 Appendix 3−2 6/17/21 PCG A−16 5/19/22 PCG M−6 5/19/22 Appendix 3−3 6/17/21 PCG A−17 5/19/22 PCG N−1 12/2/21 Appendix 3−4 6/17/21 PCG B−1 6/17/21 PCG N−2 6/17/21 Appendix 3−5 12/2/21 PCG B−2 6/17/21 PCG N−3 12/2/21 Appendix 4−1 12/2/21 PCG C−1 12/2/21 PCG N−4 6/17/21 Appendix 4−2 12/2/21 PCG C−2 12/2/21 PCG O−1 5/19/22 12/2/21 PCG C−3 5/19/22 PCG O−2 5/19/22 12/2/21 PCG C−4 12/2/21 PCG O−3 12/2/21 12/2/21 PCG C−5 12/2/21 PCG O−4 6/17/21 Appendix 4−6 12/2/21 PCG C−6 12/2/21 PCG P−1 12/2/21 Appendix 4−7 12/2/21 PCG C−7 12/2/21 PCG P−2 12/2/21 Appendix 4−8 12/2/21 PCG C−8 12/2/21 PCG P−3 5/19/22 Appendix 4−3 Appendix 4−4 Appendix 4−5 Appendix 4−9 12/2/21 PCG C−9 12/2/21 PCG P−4 5/19/22 Appendix 4−10 5/19/22 PCG C−10 12/2/21 PCG P−5 5/19/22 Appendix 4−11 12/2/21 PCG D−1 5/19/22 PCG Q−1 6/17/21 12/2/21 PCG D−2 5/19/22 PCG R−1 12/2/21 5/19/22 PCG D−3 5/19/22 PCG R−2 12/2/21 5/19/22 PCG D−4 5/19/22 PCG R−3 12/2/21 12/2/21 PCG E−1 5/19/22 PCG R−4 12/2/21 Appendix 4−12 Appendix 4−13 Appendix 4−14 Appendix 4−15 Appendix 4−16 12/2/21 PCG E−2 5/19/22 PCG R−5 12/2/21 Appendix 4−17 12/2/21 PCG E−3 5/19/22 PCG R−6 12/2/21 Appendix 4−18 12/2/21 PCG F−1 12/2/21 PCG R−7 12/2/21 Appendix 4−19 12/2/21 PCG F−2 12/2/21 PCG R−8 12/2/21 Appendix 4−20 12/2/21 PCG F−3 12/2/21 PCG S−1 6/17/21 Appendix 4−21 12/2/21 PCG F−4 12/2/21 PCG S−2 12/2/21 12/2/21 PCG S−3 12/2/21 PCG S−4 12/2/21 Appendix 4−22 12/2/21 PCG F−5 Appendix 4−23 12/2/21 PCG G−1 6/17/21 Appendix 5−1 12/2/21 PCG G−2 12/2/21 PCG S−5 12/2/21 Appendix 5−2 12/2/21 PCG G−3 12/2/21 PCG S−6 12/2/21 Appendix 5−3 12/2/21 PCG H−1 6/17/21 PCG S−7 12/2/21 PCG H−2 5/19/22 PCG S−8 5/19/22 PCG H−3 5/19/22 PCG S−9 5/19/22 PCG I−1 6/17/21 PCG S−10 5/19/22 PCG I−2 6/17/21 PCG T−1 5/19/22 PCG I−3 6/17/21 PCG T−2 12/2/21 PCG I−4 6/17/21 PCG T−3 12/2/21 PCG I−5 12/2/21 PCG T−4 12/2/21 PCG I−6 12/2/21 PCG T−5 12/2/21 PCG J−1 6/17/21 PCG T−6 12/2/21 PCG K−1 6/17/21 PCG T−7 12/2/21 PCG L−1 6/17/21 PCG T−8 12/2/21 PCG L−2 6/17/21 PCG T−9 12/2/21 PCG L−3 6/17/21 PCG U−1 6/17/21 PCG V−1 12/2/21 Pilot/Controller Glossary PCG−1 5/19/22 PCG A−1 5/19/22 PCG A−2 5/19/22 PCG A−3 PCG A−4 PCG A−5 5/19/22 5/19/22 5/19/22 PGC A−6 5/19/22 PCG A−7 5/19/22 PCG A−8 5/19/22 PCG A−9 5/19/22 PCG A−10 5/19/22 CK−6 Checklist of Pages 5/19/22 AIM Checklist of Pages DATE DATE I−8 5/19/22 DATE PCG V−2 12/2/21 PCG V−3 12/2/21 I−1 5/19/22 I−9 5/19/22 PCG V−4 12/2/21 I−2 5/19/22 I−10 5/19/22 PCG W−1 12/2/21 I−3 5/19/22 I−11 5/19/22 PCG W−2 12/2/21 I−4 5/19/22 I−12 5/19/22 I−5 5/19/22 I−13 5/19/22 I−6 5/19/22 I−7 5/19/22 Back Cover N/A Checklist of Pages PAGE PAGE PAGE Index CK−7 U.S. Department of Transportation Federal Aviation Administration AERONAUTICAL INFORMATION MANUAL Change 1 December 2, 2021 DO NOT DESTROY BASIC DATED JUNE 17, 2021 AIM 12/2/21 Aeronautical Information Manual Explanation of Changes Effective: December 2, 2021 a. 1−1−8. NAVAID SERVICE VOLUMES 1−1−17. GLOBAL POSITIONING SYSTEM (GPS) 1−1−18. WIDE AREA AUGMENTATION SYSTEM (WAAS) 1−2−3. USE OF SUITABLE AREA NAVIGATION (RNAV) SYSTEMS ON CONVENTIONAL PROCEDURES AND ROUTES 2−1−2. VISUAL GLIDESLOPE INDICATORS 3−5−8. WEATHER RECONNAISSANCE AREA (WRA) 4−1−3. FLIGHT SERVICE STATIONS 4−1−14. AUTOMATIC FLIGHT INFORMATION SERVICE (AFIS) – ALASKA FSS ONLY 4−5−9. FLIGHT INFORMATION SERVICE− BROADCAST (FIS−B) 5−1−1. PREFLIGHT PREPARATION 5−1−3. NOTICE TO AIRMEN (NOTAM) SYSTEM 5−5−1. GENERAL 7−1−5. PREFLIGHT BRIEFING 7−1−9. FLIGHT INFORMATION SERVICES (FIS) 7−6−3. OBSTRUCTIONS TO FLIGHT 7−6−12. LIGHT AMPLIFICATION BY STIMULATED EMISSION OF RADIATION (LASER) OPERATIONS AND REPORTING ILLUMINATION OF AIRCRAFT 10−2−1. OFFSHORE HELICOPTER OPERATIONS This editorial change complies with the Federal Women’s Program (FWP) suggestions. The acronym NOTAM is updated from Notice to Airmen to the more applicable term Notice to Air Missions, which is inclusive of all aviators and missions. Explanation of Changes b. 1−1−9. INSTRUMENT LANDING SYSTEM (ILS) Discussion within the PARC Pilot−Controller Procedures and Systems Integration (PCPSI) work group resulted in a recommendation to further clarify the ILS Expanded Service Volume (ESV) and include a new figure that better explains how pilots can identify an ILS ESV when consulting a charted instrument procedure. c. 1−1−17. GLOBAL POSITIONING SYSTEM The NOTAM subparagraph (g) was deleted so as not to duplicate. There is a specific NOTAM paragraph (5−1−3) that explains NOTAMs in detail. A few paragraphs were moved to supplement the RAIM paragraph. Lastly, in an effort to clarify guidance and to ensure it supports what is currently being charted in regards to the missed approach waypoint (MAWP) and the missed approach holding waypoint (MAHWP), a clearer depiction and a minor correction on how Fly−by (FB) and Fly−over (FO) waypoints are used and depicted on approach charts. d. 1−1−19. GROUND BASED AUGMENTATION SYSTEM (GBAS) LANDING SYSTEM (GLS) This change is a complete rewrite of paragraph 1−1−19 to eliminate much of the technical descriptions and to focus on the operational functions and descriptions of the GLS system. Emphasis was concentrated on GLS similarity to ILS, operational description and additional attention to familiarity with standard service volumes of GLS procedures. E of Chg−1 AIM e. 4−4−9. VFR/IFR FLIGHTS 5−1−16. RNAV AND RNP OPERATIONS 5−4−5. MINIMUM VECTORING ALTITUDE (MVA) This change rewrites the notes in off route obstruction clearance altitude (OROCA) related paragraphs, to incorporate updated terminology and enable a better understanding of how OROCA is utilized. f. 4−6−4. FLIGHT PLANNING INTO RVSM AIRSPACE 5−1−1. PREFLIGHT PREPARATION 5−1−4. FLIGHT PLAN − VFR FLIGHTS 5−1−6. FLIGHT PLAN − DEFENSE VFR (DVFR) FLIGHTS 5−1−7. COMPOSITE FLIGHT PLAN (VFR/ IFR FLIGHTS) 5−1−8. FLIGHT PLAN (FAA FORM 7233−1) − DOMESTIC IFR FLIGHTS 5−1−9. INTERNATIONAL FLIGHT PLAN (FAA FORM 7233−4) − IFR FLIGHTS (FOR DOMESTIC OR INTERNATIONAL FLIGHTS) APPENDIX 4. FAA FORM 7233−4 − INTERNATIONAL FLIGHT PLAN APPENDIX 5. FAA FORM 7233−1 − FLIGHT PLAN The following changes are required to align the order with current operational procedures. These changes also support the standardized use of FAA Form 7233−4, International Flight Plan, and inform stakeholders that legacy procedures may be used by parties that do not have the necessary equipment to adhere to the new ICAO forms and or procedures. g. 5−1−3. NOTICE TO AIRMEN (NOTAM) SYSTEM GPS NOTAM and receiver autonomous integrity monitoring (RAIM) information is currently located in the overview section of the AIM/AIP. This change consolidates all of the NOTAM information into one procedures section and updates current NOTAM language. This update references how to report GPS anomalies, as well as edits two tables with example NOTAMS on GPS testing and pseudo−random satellite numbers. 12/2/21 planning information being updated to reflect the two temperature limitations that may be found on an FAA produced instrument approach procedure (IAP). The new paragraph also directs operators to Chapter 7 to review the information on cold temperature altimetry errors and current procedures for CTA and baro−VNAV temperature limitations. i. 5−2−7. DEPARTURE RESTRICTIONS, CLEARANCE VOID TIMES, HOLD FOR RELEASE, AND RELEASE TIMES A recent change to FAA Order JO 7110.65 requires that ATC give a pilot departing from an airport without an operating control tower a departure release, a hold for release, or a release time when issuing the departure clearance. This AIM change reflects the change made to FAA Order JO 7110.65 and clarifies pilot and controller responsibilities. j. 5−2−8. DEPARTURE CONTROL 5−2−9. INSTRUMENT DEPARTURE PROCEDURES (DP) − OBSTACLE DEPARTURE PROCEDURES (ODP), STANDARD INSTRUMENT DEPARTURES (SID), AND DIVERSE VECTOR AREAS (DVA) 5−5−6. RADAR VECTORS 5−5−14. INSTRUMENT DEPARTURES This change adds a statement that diverse vector areas (DVAs) cannot be used concurrently with a standard instrument departure (SID) when the SID is included as part of the instrument flight rules (IFR) clearance, and addresses a new requirement imposed on ATC that pilots will receive an amended clearance if departure procedures are changed from SIDs to DVAs and vice versa. k. 5−2−9. INSTRUMENT DEPARTURE PROCEDURES (DP) − OBSTACLE DEPARTURE PROCEDURES (ODP), STANDARD INSTRUMENT DEPARTURES (SID), AND DIVERSE VECTOR AREAS (DVA) Instructions and clarity were added for pilots to remain within the visual climb over airport (VCOA) specified visibility when departing an airport instrument flight rules (IFR) using VCOA. h. 5−1−17. COLD TEMPERATURE OPERATIONS l. 5−4−5. INSTRUMENT APPROACH PROCEDURE (IAP) CHARTS 5−5−4. INSTRUMENT APPROACH 5−5−5. MISSED APPROACH This change replaces paragraph 5−1−17 Cold Temperature Operations guidance and preflight This change renames paragraph 5−4−5m7(f) from Hot and Cold Temperature Limitations to Published E of Chg−2 Explanation of Changes AIM 12/2/21 Temperature Limitations, and also adds information on the two published temperature limitations. Paragraph 5−5−4 will give a brief description of the two temperature limitations found on the Instrument Approach Procedures (IAPs). Paragraph 5−5−5 will mention the Cold Temperature Airports (CTA) ICON and discuss briefly when to correct and who to contact. m. 5−4−18. RNP AR (AUTHORIZATION REQUIRED) INSTRUMENT APPROACH PROCEDURES This change deletes most of this paragraph. All that is necessary in this publication is a brief overview of Required Navigation Performance Authorization Required (RNP AR) and reference to a complete AC dedicated to RNP AR. n. 5−4−20. APPROACH AND LANDING MINIMUMS Removes outdated and incorrect verbiage and re−aligns AIM/AIP verbiage with FAA Order 8260.58. o. 5−6−8. FOREIGN STATE AIRCRAFT OPERATIONS Guidance for Foreign State Aircraft operating with a Department of State issued Diplomatic Clearance is being added to the Aeronautical Information Manual regarding authorizations to deviate from Automatic Dependent Surveillance−Broadcast (ADS−B) requirements. p. 7−1−8. INFLIGHT WEATHER ADVISORY BROADCASTS This change removes Severe Weather Forecast Alerts (AWW) from paragraph 7−1−8, Inflight Weather Advisory Broadcasts, which are not broadcast by Terminal or ARTCC controllers. The change also harmonizes paragraph 7−1−8a Note with FAA Order JO 7110.65, subparagraph 2−6−6b, and adds a Reference to that paragraph. q. 7−1−24. MICROBURSTS These changes update the information in this chapter regarding Low Level Wind Shear Alert System (LLWAS), Terminal Doppler Weather Radar (TDWR), and Weather System Processor (WSP). Explanation of Changes r. 7−6−16. SPACE LAUNCH AND REENTRY AREA This change relocates the space launch activity area information that was previously in Chart Supplement publications into the AIM and AIP. The term “space launch activity area” was also updated to the more inclusive “space launch and reentry area.” s. 9−1−4. GENERAL DESCRIPTION OF EACH CHART SERIES This change updates frequency of chart production. In cases where annually or biannual updates were made, 56 day chart updates replace those longer update periods, and reduce the NOTAM burden and bring NAS changes to aviators in a timely manner. t. 10−1−2. HELICOPTER INSTRUMENT APPROACHES 10−1−3. HELICOPTER APPROACH PROCEDURES TO VFR HELIPORTS Changes were made throughout the section to improve the clarity and provide updated information wherever necessary. Emphasis was concentrated on clarification of language and operational description associated with helicopter instrument approach procedures. u. 10−1−5. DEPARTURE PROCEDURES This addition was made to improve the clarity and provide departure information wherever necessary. Emphasis was concentrated on clarification of language and operational description associated with helicopter instrument departure procedures. v. Editorial Changes Editorial changes include updates to an out of date reference in paragraph 3−4−1, a formatting fix in paragraph 7−1−13, a math error correction in paragraph 7−3−6, correcting Las Vegas McCarran International to Harry Reid International in paragraph 4−5−5 (TBL 4−5−1), removing an incorrect reference in paragraph 7−4−1, and adding a missing “traffic advisories.” w. Entire Publication Additional editorial/format changes were made where necessary. Revision bars were not used because of the insignificant nature of these changes. E of Chg−3 12/2/21 AIM AIM Change 1 Page Control Chart December 2, 2021 REMOVE PAGES DATED INSERT PAGES Checklist of Pages CK−1 through CK−7 . . . . Table of Contents i through xii . . . . . . . . . . . 1−1−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−10 through 1−1−16 . . . . . . . . . . . . . . . . . 1−1−19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−23 through 1−1−40 . . . . . . . . . . . . . . . . . 1−2−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−2−6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−2−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−2−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−1−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−1−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−4−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−4−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−5−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−5−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−1 and 4−1−2 . . . . . . . . . . . . . . . . . . . . . . 4−1−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−17 through 4−1−19 . . . . . . . . . . . . . . . . . 4−2−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−2−4 through 4−2−8 . . . . . . . . . . . . . . . . . . . 4−3−13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−3−14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−3−23 through 4−3−32 . . . . . . . . . . . . . . . . . 4−4−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−4−6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−5−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−5−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−5−19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−5−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−6−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−6−2 through 4−6−10 . . . . . . . . . . . . . . . . . . 5−1−1 through 5−1−31 . . . . . . . . . . . . . . . . . . 5−2−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 Checklist of Pages CK−1 through CK−7 . . . . Table of Contents i through xii . . . . . . . . . . . 1−1−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−10 through 1−1−16 . . . . . . . . . . . . . . . . 1−1−19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1−23 through 1−1−39 . . . . . . . . . . . . . . . . . 1−2−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−2−6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−2−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−2−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−1−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−1−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−4−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−4−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−5−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−5−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−1 and 4−1−2 . . . . . . . . . . . . . . . . . . . . . . 4−1−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−1−17 through 4−1−19 . . . . . . . . . . . . . . . . . 4−2−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−2−4 through 4−2−8 . . . . . . . . . . . . . . . . . . . 4−3−13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−3−14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−3−23 through 4−3−32 . . . . . . . . . . . . . . . . . 4−4−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−4−6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−5−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−5−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−5−19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−5−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−6−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4−6−2 through 4−6−9 . . . . . . . . . . . . . . . . . . . 5−1−1 through 5−1−18 . . . . . . . . . . . . . . . . . . 5−2−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Control Chart DATED 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 12/2/21 12/2/21 6/17/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 i 12/2/21 AIM 5−2−4 through 5−2−13 . . . . . . . . . . . . . . . . . . 5−4−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−25 through 5−4−65 . . . . . . . . . . . . . . . . . 5−5−1 through 5−5−8 . . . . . . . . . . . . . . . . . . . 5−6−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−6−6 through 5−6−11 . . . . . . . . . . . . . . . . . . 5−6−12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−18 and 7−1−19 . . . . . . . . . . . . . . . . . . . . 7−1−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−37 and 7−1−38 . . . . . . . . . . . . . . . . . . . . 7−1−47 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−50 and 7−1−51 . . . . . . . . . . . . . . . . . . . . 7−1−52 and 7−1−53 . . . . . . . . . . . . . . . . . . . . 7−1−54 through 7−1−58 . . . . . . . . . . . . . . . . . 7−3−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−3−6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..................................... 9−1−1 through 9−1−4 . . . . . . . . . . . . . . . . . . . 9−1−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10−1−1 through 10−1−7 . . . . . . . . . . . . . . . . . 10−2−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10−2−2 and 10−2−3 . . . . . . . . . . . . . . . . . . . . 10−2−4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 3−5 . . . . . . . . . . . . . . . . . . . . . . . . . ..................................... ..................................... PCG−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG A−1 through PCG A−17 . . . . . . . . . . . . PCG C−1 through PCG C−10 . . . . . . . . . . . . PCG D−1 through PCG D−4 . . . . . . . . . . . . . ii 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 N/A 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 N/A N/A 6/17/21 6/17/21 6/17/21 6/17/21 5−2−4 through 5−2−13 . . . . . . . . . . . . . . . . . . 5−4−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−4−25 through 5−4−63 . . . . . . . . . . . . . . . . . 5−5−1 through 5−5−9 . . . . . . . . . . . . . . . . . . . 5−6−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5−6−6 through 5−6−11 . . . . . . . . . . . . . . . . . . 5−6−12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−18 and 7−1−19 . . . . . . . . . . . . . . . . . . . . 7−1−20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−37 and 7−1−38 . . . . . . . . . . . . . . . . . . . . 7−1−47 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−1−50 and 7−1−51 . . . . . . . . . . . . . . . . . . . . 7−1−52 and 7−1−53 . . . . . . . . . . . . . . . . . . . . 7−1−54 through 7−1−58 . . . . . . . . . . . . . . . . . 7−3−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−3−6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7−6−15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−1 through 9−1−4 . . . . . . . . . . . . . . . . . . . 9−1−7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9−1−12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10−1−1 through 10−1−7 . . . . . . . . . . . . . . . . . 10−2−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10−2−2 and 10−2−3 . . . . . . . . . . . . . . . . . . . . 10−2−4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 3−5 . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 4−1 through Appendix 4−23 . . . . . Appendix 5−1 through Appendix 5−3 . . . . . . PCG−1 and PCG−2 . . . . . . . . . . . . . . . . . . . . PCG A−1 through PCG A−17 . . . . . . . . . . . . PCG C−1 through PCG C−10 . . . . . . . . . . . . PCG D−1 through PCG D−4 . . . . . . . . . . . . . 12/2/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 6/17/21 12/2/21 12/2/21 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 12/2/21 12/2/21 12/2/21 12/2/21 12/2/21 12/2/21 Page Control Chart 12/2/21 PCG E−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG E−2 and PCG E−3 . . . . . . . . . . . . . . . . . PCG F−1 through PCG F−5 . . . . . . . . . . . . . . PCG G−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG G−2 through PCG G−3 . . . . . . . . . . . . . PCG I−1 through PCG I−6 . . . . . . . . . . . . . . . PCG M−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG M−2 through PCG M−6 . . . . . . . . . . . . PCG N−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG N−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG N−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG N−4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG O−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG O−2 and PCG O−3 . . . . . . . . . . . . . . . . PCG O−4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG P−1 through PCG P−5 . . . . . . . . . . . . . . PCG R−1 through PCG R−8 . . . . . . . . . . . . . PCG S−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG S−2 through PCG S−9 . . . . . . . . . . . . . . PCG T−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG T−2 through PCG T−8 . . . . . . . . . . . . . . PCG V−1 through PCG V−4 . . . . . . . . . . . . . PCG W−1 and PGC W−2 . . . . . . . . . . . . . . . . Index I−1 through I−12 . . . . . . . . . . . . . . . . . Page Control Chart AIM 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 6/17/21 PCG E−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG E−2 and PCG E−3 . . . . . . . . . . . . . . . . . PCG F−1 through PCG F−5 . . . . . . . . . . . . . . PCG G−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG G−2 through PCG G−3 . . . . . . . . . . . . . PCG I−5 and PCG I−6 . . . . . . . . . . . . . . . . . . PCG M−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG M−2 through PCG M−6 . . . . . . . . . . . . PCG N−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG N−2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG N−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG N−4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG O−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG O−2 and PCG O−3 . . . . . . . . . . . . . . . . PCG O−4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG P−1 through PCG P−6 . . . . . . . . . . . . . . PCG R−1 through PCG R−8 . . . . . . . . . . . . . PCG S−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG S−2 through PCG S−10 . . . . . . . . . . . . . PCG T−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG T−2 through PCG T−9 . . . . . . . . . . . . . . PCG V−1 through PCG V−4 . . . . . . . . . . . . . PCG W−1 and PGC W−2 . . . . . . . . . . . . . . . . Index I−1 through I−13 . . . . . . . . . . . . . . . . . 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 6/17/21 12/2/21 6/17/21 12/2/21 12/2/21 6/17/21 12/2/21 6/17/21 12/2/21 12/2/21 12/2/21 12/2/21 iii 12/2/21 AIM Checklist of Pages PAGE DATE PAGE DATE Cover 6/17/21 1−1−12 12/2/21 Record of Changes N/A 1−1−13 12/2/21 Exp of Chg−1 12/2/21 1−1−14 12/2/21 Exp of Chg−2 12/2/21 1−1−15 12/2/21 Exp of Chg−3 12/2/21 1−1−16 12/2/21 PAGE DATE Chapter 2. Aeronautical Lighting and Other Airport Visual Aids Section 1. Airport Lighting Aids 1−1−17 6/17/21 2−1−1 12/2/21 1−1−18 6/17/21 2−1−2 6/17/21 12/2/21 1−1−19 6/17/21 2−1−3 6/17/21 12/2/21 1−1−20 12/2/21 2−1−4 6/17/21 12/2/21 1−1−21 6/17/21 2−1−5 6/17/21 12/2/21 1−1−22 6/17/21 2−1−6 6/17/21 12/2/21 1−1−23 12/2/21 2−1−7 6/17/21 CK−6 12/2/21 1−1−24 12/2/21 2−1−8 6/17/21 CK−7 12/2/21 Checklist of Pages CK−1 CK−2 CK−3 CK−4 CK−5 1−1−25 12/2/21 2−1−9 6/17/21 1−1−26 12/2/21 2−1−10 6/17/21 6/17/21 1−1−27 12/2/21 2−1−11 6/17/21 6/17/21 1−1−28 12/2/21 2−1−12 6/17/21 6/17/21 1−1−29 12/2/21 2−1−13 6/17/21 Publication Policy 6/17/21 1−1−30 12/2/21 Reg & Advis Cir 6/17/21 1−1−31 12/2/21 1−1−32 12/2/21 1−1−33 12/2/21 2−2−1 6/17/21 1−1−34 12/2/21 2−2−2 6/17/21 1−1−35 12/2/21 1−1−36 12/2/21 1−1−37 12/2/21 Subscription Info Comments/Corr Basic Flight Info Table of Contents i 12/2/21 ii 12/2/21 iii 12/2/21 iv 12/2/21 v 12/2/21 vi vii viii ix x xi xii Section 2. Air Navigation and Obstruction Lighting Section 3. Airport Marking Aids and Signs 1−1−38 12/2/21 2−3−1 6/17/21 1−1−39 12/2/21 2−3−2 6/17/21 12/2/21 2−3−3 6/17/21 12/2/21 2−3−4 6/17/21 12/2/21 2−3−5 6/17/21 2−3−6 6/17/21 2−3−7 6/17/21 2−3−8 6/17/21 12/2/21 12/2/21 12/2/21 12/2/21 Chapter 1. Air Navigation Section 1. Navigation Aids Section 2. Performance−Based Navigation (PBN) and Area Navigation (RNAV) 1−2−1 6/17/21 2−3−9 6/17/21 1−2−2 6/17/21 2−3−10 6/17/21 1−2−3 6/17/21 2−3−11 6/17/21 1−2−4 6/17/21 2−3−12 6/17/21 1−1−1 6/17/21 1−2−5 12/2/21 1−1−2 6/17/21 2−3−13 6/17/21 1−2−6 6/17/21 1−1−3 6/17/21 2−3−14 6/17/21 1−2−7 6/17/21 1−1−4 6/17/21 2−3−15 6/17/21 1−2−8 12/2/21 1−1−5 6/17/21 2−3−16 6/17/21 1−2−9 6/17/21 1−1−6 12/2/21 2−3−17 6/17/21 1−2−10 6/17/21 1−1−7 6/17/21 2−3−18 6/17/21 1−1−8 6/17/21 2−3−19 6/17/21 1−1−9 6/17/21 2−3−20 6/17/21 1−1−10 12/2/21 2−3−21 6/17/21 1−1−11 12/2/21 2−3−22 6/17/21 Checklist of Pages CK−1 AIM 12/2/21 Checklist of Pages PAGE DATE PAGE DATE PAGE DATE 2−3−23 6/17/21 2−3−24 6/17/21 2−3−25 6/17/21 2−3−26 6/17/21 2−3−27 6/17/21 4−3−15 6/17/21 2−3−28 6/17/21 4−1−1 12/2/21 4−3−16 6/17/21 2−3−29 6/17/21 4−1−2 12/2/21 4−3−17 6/17/21 2−3−30 6/17/21 4−1−3 6/17/21 4−3−18 6/17/21 2−3−31 6/17/21 4−1−4 6/17/21 4−3−19 6/17/21 4−1−5 6/17/21 4−3−20 6/17/21 4−1−6 6/17/21 4−3−21 6/17/21 6/17/21 4−3−22 6/17/21 12/2/21 4−3−23 12/2/21 12/2/21 Chapter 3. Airspace Section 1. General 3−1−1 6/17/21 4−1−7 4−1−8 4−3−11 6/17/21 4−3−12 6/17/21 4−3−13 12/2/21 4−3−14 6/17/21 3−1−2 6/17/21 4−1−9 6/17/21 4−3−24 3−1−3 6/17/21 4−1−10 6/17/21 4−3−25 12/2/21 12/2/21 Section 2. Controlled Airspace 4−1−11 6/17/21 4−3−26 4−1−12 12/2/21 4−3−27 12/2/21 6/17/21 4−3−28 12/2/21 6/17/21 4−3−29 12/2/21 6/17/21 4−3−30 12/2/21 6/17/21 4−3−31 12/2/21 4−3−32 12/2/21 3−2−1 6/17/21 4−1−13 3−2−2 6/17/21 4−1−14 3−2−3 6/17/21 4−1−15 3−2−4 6/17/21 4−1−16 3−2−5 6/17/21 4−1−17 12/2/21 6/17/21 4−1−18 12/2/21 3−2−7 6/17/21 4−1−19 12/2/21 3−2−8 6/17/21 3−2−9 6/17/21 3−2−6 3−2−10 6/17/21 Section 3. Class G Airspace 3−3−1 6/17/21 Section 4. Special Use Airspace 3−4−1 12/2/21 3−4−2 6/17/21 3−4−3 6/17/21 Section 5. Other Airspace Areas 3−5−1 6/17/21 3−5−2 6/17/21 3−5−3 6/17/21 3−5−4 6/17/21 3−5−5 6/17/21 3−5−6 6/17/21 3−5−7 6/17/21 3−5−8 6/17/21 3−5−9 6/17/21 3−5−10 12/2/21 CK−2 Chapter 4. Air Traffic Control Section 1. Services Available to Pilots Section 4. ATC Clearances and Aircraft Separation 4−4−1 6/17/21 4−4−2 6/17/21 4−4−3 6/17/21 6/17/21 4−4−4 6/17/21 4−2−2 6/17/21 4−4−5 12/2/21 4−2−3 6/17/21 4−4−6 6/17/21 4−2−4 12/2/21 4−4−7 6/17/21 4−2−5 12/2/21 4−4−8 6/17/21 4−2−6 12/2/21 4−4−9 6/17/21 4−2−7 12/2/21 4−4−10 6/17/21 4−2−8 12/2/21 4−4−11 6/17/21 4−4−12 6/17/21 Section 2. Radio Communications Phraseology and Techniques 4−2−1 Section 3. Airport Operations Section 5. Surveillance Systems 4−3−1 6/17/21 4−3−2 6/17/21 4−3−3 6/17/21 4−5−1 6/17/21 6/17/21 4−5−2 6/17/21 6/17/21 4−5−3 6/17/21 6/17/21 4−5−4 6/17/21 4−3−7 6/17/21 4−5−5 6/17/21 4−3−8 6/17/21 4−5−6 6/17/21 4−3−9 6/17/21 4−5−7 6/17/21 4−3−10 6/17/21 4−5−8 12/2/21 4−5−9 6/17/21 4−3−4 4−3−5 4−3−6 Checklist of Pages 12/2/21 AIM Checklist of Pages DATE PAGE DATE 5−1−9 12/2/21 5−3−21 6/17/21 5−1−10 12/2/21 5−3−22 6/17/21 5−1−11 12/2/21 5−3−23 6/17/21 6/17/21 5−1−12 12/2/21 5−3−24 6/17/21 6/17/21 5−1−13 12/2/21 5−3−25 6/17/21 12/2/21 5−3−26 6/17/21 12/2/21 5−3−27 6/17/21 5−3−28 6/17/21 PAGE DATE 4−5−10 6/17/21 4−5−11 6/17/21 4−5−12 6/17/21 4−5−13 4−5−14 4−5−15 6/17/21 PAGE 5−1−14 4−5−16 6/17/21 5−1−15 4−5−17 6/17/21 5−1−16 12/2/21 4−5−18 6/17/21 5−1−17 12/2/21 4−5−19 6/17/21 5−1−18 12/2/21 4−5−20 12/2/21 4−5−21 6/17/21 4−5−22 6/17/21 Section 6. Operational Policy/ Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR Section 4. Arrival Procedures 5−4−1 6/17/21 Section 2. Departure Procedures 5−4−2 6/17/21 5−4−3 6/17/21 5−2−1 6/17/21 5−4−4 6/17/21 5−2−2 6/17/21 5−4−5 6/17/21 5−2−3 6/17/21 5−4−6 6/17/21 5−2−4 12/2/21 5−4−7 6/17/21 5−2−5 12/2/21 5−4−8 6/17/21 5−2−6 12/2/21 5−4−9 6/17/21 4−6−1 6/17/21 5−2−7 12/2/21 5−4−10 6/17/21 4−6−2 12/2/21 5−2−8 12/2/21 5−4−11 6/17/21 4−6−3 12/2/21 5−2−9 12/2/21 5−4−12 6/17/21 4−6−4 12/2/21 5−2−10 12/2/21 5−4−13 6/17/21 4−6−5 12/2/21 5−2−11 12/2/21 5−4−14 6/17/21 4−6−6 12/2/21 5−2−12 12/2/21 5−4−15 6/17/21 4−6−7 12/2/21 5−2−13 12/2/21 5−4−16 6/17/21 4−6−8 12/2/21 5−4−17 12/2/21 4−6−9 12/2/21 5−4−18 6/17/21 5−4−19 6/17/21 Section 7. Operational Policy/ Procedures for the Gulf of Mexico 50 NM Lateral Separation Initiative 4−7−1 6/17/21 4−7−2 6/17/21 Chapter 5. Air Traffic Procedures Section 1. Preflight 5−1−1 12/2/21 5−1−2 12/2/21 5−1−3 12/2/21 5−1−4 12/2/21 5−1−5 12/2/21 5−1−6 12/2/21 5−1−7 12/2/21 5−1−8 12/2/21 Checklist of Pages Section 3. En Route Procedures 5−3−1 6/17/21 5−4−20 6/17/21 5−3−2 6/17/21 5−4−21 6/17/21 5−3−3 6/17/21 5−4−22 6/17/21 6/17/21 5−4−23 6/17/21 5−3−5 6/17/21 5−4−24 6/17/21 5−3−6 6/17/21 5−4−25 12/2/21 5−3−7 6/17/21 5−4−26 12/2/21 5−3−8 6/17/21 5−4−27 12/2/21 5−3−9 6/17/21 5−4−28 12/2/21 5−3−10 6/17/21 5−4−29 12/2/21 5−3−11 6/17/21 5−4−30 12/2/21 5−3−12 6/17/21 5−4−31 12/2/21 6/17/21 5−4−32 12/2/21 5−3−14 6/17/21 5−4−33 12/2/21 5−3−15 6/17/21 5−4−34 12/2/21 5−3−16 6/17/21 5−4−35 12/2/21 5−3−17 6/17/21 5−4−36 12/2/21 5−3−18 6/17/21 5−4−37 12/2/21 5−3−19 6/17/21 5−4−38 12/2/21 5−3−20 6/17/21 5−4−39 12/2/21 5−3−4 5−3−13 CK−3 AIM 12/2/21 Checklist of Pages PAGE DATE PAGE DATE 5−4−40 12/2/21 5−6−10 12/2/21 5−4−41 12/2/21 5−6−11 12/2/21 5−4−42 12/2/21 5−6−12 6/17/21 7−1−1 6/17/21 5−4−43 12/2/21 5−6−13 6/17/21 7−1−2 6/17/21 5−4−44 12/2/21 5−6−14 6/17/21 7−1−3 6/17/21 5−4−45 12/2/21 7−1−4 6/17/21 5−4−46 12/2/21 7−1−5 6/17/21 5−4−47 12/2/21 Chapter 6. Emergency Procedures 7−1−6 6/17/21 5−4−48 12/2/21 Section 1. General 7−1−7 6/17/21 5−4−49 12/2/21 7−1−8 12/2/21 5−4−50 12/2/21 7−1−9 6/17/21 5−4−51 12/2/21 7−1−10 6/17/21 5−4−52 12/2/21 7−1−11 6/17/21 5−4−53 12/2/21 6/17/21 7−1−12 6/17/21 5−4−54 12/2/21 6/17/21 7−1−13 6/17/21 5−4−55 12/2/21 6−2−3 6/17/21 7−1−14 6/17/21 5−4−56 12/2/21 6−2−4 6/17/21 7−1−15 6/17/21 5−4−57 12/2/21 6−2−5 6/17/21 7−1−16 6/17/21 5−4−58 12/2/21 6−2−6 6/17/21 7−1−17 12/2/21 5−4−59 12/2/21 6−2−7 6/17/21 7−1−18 6/17/21 5−4−60 12/2/21 6−2−8 6/17/21 7−1−19 6/17/21 5−4−61 12/2/21 6−2−9 6/17/21 7−1−20 12/2/21 5−4−62 12/2/21 6/17/21 7−1−21 6/17/21 5−4−63 12/2/21 6/17/21 7−1−22 6/17/21 7−1−23 6/17/21 7−1−24 6/17/21 7−1−25 6/17/21 6/17/21 7−1−26 6/17/21 6/17/21 7−1−27 6/17/21 6/17/21 7−1−28 6/17/21 6/17/21 7−1−29 6/17/21 6/17/21 Section 5. Pilot/Controller Roles and Responsibilities 6−1−1 Section 2. Emergency Services Available to Pilots 6−2−1 6−2−2 6−2−10 6−2−11 Section 3. Distress and Urgency Procedures 6−3−1 DATE Chapter 7. Safety of Flight Section 1. Meteorology 5−5−1 12/2/21 6−3−2 5−5−2 12/2/21 6−3−3 5−5−3 12/2/21 6−3−4 5−5−4 12/2/21 6−3−5 6/17/21 7−1−30 5−5−5 12/2/21 6−3−6 6/17/21 7−1−31 6/17/21 5−5−6 12/2/21 6−3−7 6/17/21 7−1−32 6/17/21 5−5−7 12/2/21 7−1−33 6/17/21 5−5−8 12/2/21 7−1−34 6/17/21 5−5−9 12/2/21 7−1−35 6/17/21 6/17/21 7−1−36 6/17/21 6/17/21 7−1−37 12/2/21 7−1−38 12/2/21 7−1−39 6/17/21 7−1−40 6/17/21 7−1−41 6/17/21 7−1−42 6/17/21 7−1−43 6/17/21 Section 4. Two−way Radio Communications Failure 6−4−1 Section 6. National Security and Interception Procedures 5−6−1 6/17/21 5−6−2 6/17/21 5−6−3 6/17/21 5−6−4 5−6−5 5−6−6 5−6−7 5−6−8 5−6−9 CK−4 6/17/21 PAGE 6/17/21 6/17/21 6−4−2 Section 5. Aircraft Rescue and Fire Fighting Communications 6−5−1 6/17/21 7−1−44 6/17/21 6−5−2 6/17/21 7−1−45 6/17/21 12/2/21 7−1−46 6/17/21 12/2/21 7−1−47 6/17/21 12/2/21 12/2/21 Checklist of Pages 12/2/21 AIM Checklist of Pages PAGE DATE PAGE DATE 7−1−48 12/2/21 7−4−7 6/17/21 7−1−49 6/17/21 7−4−8 6/17/21 7−1−50 12/2/21 7−1−51 12/2/21 7−1−52 6/17/21 7−1−53 6/17/21 9−1−1 12/2/21 7−1−54 12/2/21 7−5−1 6/17/21 9−1−2 12/2/21 7−1−55 12/2/21 7−5−2 6/17/21 9−1−3 12/2/21 7−1−56 12/2/21 9−1−4 12/2/21 7−1−57 12/2/21 9−1−5 6/17/21 7−1−58 12/2/21 9−1−6 6/17/21 7−1−59 6/17/21 7−6−1 12/2/21 9−1−7 12/2/21 7−1−60 6/17/21 7−6−2 6/17/21 9−1−8 6/17/21 7−1−61 6/17/21 7−6−3 6/17/21 9−1−9 12/2/21 7−1−62 6/17/21 7−6−4 6/17/21 9−1−10 6/17/21 7−1−63 6/17/21 7−6−5 6/17/21 9−1−11 12/2/21 7−1−64 6/17/21 7−6−6 6/17/21 9−1−12 6/17/21 7−1−65 6/17/21 7−6−7 6/17/21 9−1−13 6/17/21 7−1−66 6/17/21 7−6−8 6/17/21 7−1−67 6/17/21 7−6−9 6/17/21 7−1−68 6/17/21 7−6−10 12/2/21 7−1−69 6/17/21 7−6−11 6/17/21 7−1−70 6/17/21 7−6−12 6/17/21 7−6−13 6/17/21 10−1−1 12/2/21 7−6−14 6/17/21 10−1−2 12/2/21 7−6−15 12/2/21 10−1−3 12/2/21 10−1−4 12/2/21 10−1−5 12/2/21 10−1−6 12/2/21 10−1−7 12/2/21 Section 2. Barometric Altimeter Errors and Setting Procedures 7−2−1 6/17/21 7−2−2 6/17/21 7−2−3 6/17/21 Section 3. Cold Temperature Barometric Altimeter Errors, Setting Procedures and Cold Temperature Airports (CTA) 7−3−1 7−3−2 7−3−3 7−3−4 6/17/21 6/17/21 6/17/21 6/17/21 7−3−5 6/17/21 7−3−6 12/2/21 7−3−7 6/17/21 Section 4. Wake Turbulence 7−4−1 6/17/21 7−4−2 6/17/21 7−4−3 6/17/21 7−4−4 6/17/21 7−4−5 6/17/21 7−4−6 6/17/21 Checklist of Pages Section 5. Bird Hazards and Flight Over National Refuges, Parks, and Forests Section 6. Potential Flight Hazards Section 7. Safety, Accident, and Hazard Reports 7−7−1 6/17/21 7−7−2 6/17/21 7−7−3 6/17/21 Chapter 8. Medical Facts for Pilots Section 1. Fitness for Flight PAGE DATE Chapter 9. Aeronautical Charts and Related Publications Section 1. Types of Charts Available Chapter 10. Helicopter Operations Section 1. Helicopter IFR Operations Section 2. Special Operations 10−2−1 6/17/21 10−2−2 12/2/21 10−2−3 12/2/21 10−2−4 6/17/21 10−2−5 6/17/21 8−1−1 6/17/21 10−2−6 6/17/21 8−1−2 6/17/21 10−2−7 6/17/21 8−1−3 6/17/21 10−2−8 6/17/21 8−1−4 6/17/21 10−2−9 6/17/21 8−1−5 6/17/21 10−2−10 6/17/21 8−1−6 6/17/21 10−2−11 6/17/21 8−1−7 6/17/21 10−2−12 6/17/21 8−1−8 6/17/21 10−2−13 6/17/21 8−1−9 6/17/21 10−2−14 6/17/21 10−2−15 6/17/21 10−2−16 6/17/21 10−2−17 6/17/21 CK−5 AIM 12/2/21 Checklist of Pages PAGE DATE PAGE DATE PAGE DATE PCG A−10 12/2/21 PCG M−1 6/17/21 Appendix 1−1 6/17/21 PCG A−11 12/2/21 PCG M−2 12/2/21 Env N/A PCG A−13 12/2/21 PCG M−3 12/2/21 6/17/21 PCG A−12 12/2/21 PCG M−4 12/2/21 6/17/21 PCG A−14 12/2/21 PCG M−5 12/2/21 6/17/21 PCG A−15 12/2/21 PCG M−6 12/2/21 Appendix 3−3 6/17/21 PCG A−16 12/2/21 PCG N−1 12/2/21 Appendix 3−4 6/17/21 PCG A−17 12/2/21 PCG N−2 6/17/21 Appendix 3−5 12/2/21 PCG B−1 6/17/21 PCG N−3 12/2/21 Appendix 4−1 12/2/21 PCG B−2 6/17/21 PCG N−4 6/17/21 Appendix 4−2 12/2/21 PCG C−1 12/2/21 PCG O−1 6/17/21 12/2/21 PCG C−2 12/2/21 PCG O−2 12/2/21 12/2/21 PCG C−3 12/2/21 PCG O−3 12/2/21 12/2/21 PCG C−4 12/2/21 PCG O−4 6/17/21 Appendix 4−6 12/2/21 PCG C−5 12/2/21 PCG P−1 12/2/21 Appendix 4−7 12/2/21 PCG C−6 12/2/21 PCG P−2 12/2/21 Appendix 4−8 12/2/21 PCG C−7 12/2/21 PCG P−3 12/2/21 Appendix 4−9 12/2/21 PCG C−8 12/2/21 PCG P−4 12/2/21 Appendix 4−10 12/2/21 PCG C−9 12/2/21 PCG P−5 12/2/21 Appendix 4−11 12/2/21 PCG C−10 12/2/21 PCG P−6 12/2/21 12/2/21 PCG D−1 12/2/21 PCG Q−1 6/17/21 12/2/21 PCG D−2 12/2/21 PCG R−1 12/2/21 12/2/21 PCG D−3 12/2/21 PCG R−2 12/2/21 Appendix 4−15 12/2/21 PCG D−4 12/2/21 PCG R−3 12/2/21 Appendix 4−16 12/2/21 PCG E−1 6/17/21 PCG R−4 12/2/21 Appendix 4−17 12/2/21 PCG E−2 12/2/21 PCG R−5 12/2/21 Appendix 4−18 12/2/21 PCG E−3 12/2/21 PCG R−6 12/2/21 Appendix 4−19 12/2/21 PCG F−1 12/2/21 PCG R−7 12/2/21 12/2/21 PCG F−2 12/2/21 PCG R−8 12/2/21 12/2/21 PCG F−3 12/2/21 PCG S−1 6/17/21 12/2/21 PCG F−4 12/2/21 PCG S−2 12/2/21 Appendix 4−23 12/2/21 PCG F−5 12/2/21 PCG S−3 12/2/21 Appendix 5−1 12/2/21 PCG G−1 6/17/21 PCG S−4 12/2/21 Appendix 5−2 12/2/21 PCG G−2 12/2/21 PCG S−5 12/2/21 Appendix 5−3 12/2/21 PCG G−3 12/2/21 PCG S−6 12/2/21 PCG H−1 6/17/21 PCG S−7 12/2/21 PCG H−2 6/17/21 PCG S−8 12/2/21 PCG H−3 6/17/21 PCG S−9 12/2/21 12/2/21 PCG I−1 6/17/21 PCG S−10 12/2/21 PCG−2 12/2/21 PCG I−2 6/17/21 PCG T−1 6/17/21 PCG A−1 12/2/21 PCG I−3 6/17/21 PCG T−2 12/2/21 12/2/21 PCG I−4 6/17/21 PCG T−3 12/2/21 12/2/21 PCG I−5 12/2/21 PCG T−4 12/2/21 12/2/21 PCG I−6 12/2/21 PCG T−5 12/2/21 12/2/21 PCG J−1 6/17/21 PCG T−6 12/2/21 PGC A−6 12/2/21 PCG K−1 6/17/21 PCG T−7 12/2/21 PCG A−7 12/2/21 PCG L−1 6/17/21 PCG T−8 12/2/21 PCG A−8 12/2/21 PCG L−2 6/17/21 PCG T−9 12/2/21 PCG A−9 12/2/21 PCG L−3 6/17/21 Appendices Appendix 2−1 Appendix 3−1 Appendix 3−2 Appendix 4−3 Appendix 4−4 Appendix 4−5 Appendix 4−12 Appendix 4−13 Appendix 4−14 Appendix 4−20 Appendix 4−21 Appendix 4−22 Pilot/Controller Glossary PCG−1 PCG A−2 PCG A−3 PCG A−4 PCG A−5 CK−6 Checklist of Pages 12/2/21 AIM Checklist of Pages PAGE DATE PAGE DATE I−8 12/2/21 I−9 12/2/21 12/2/21 I−10 12/2/21 12/2/21 I−11 12/2/21 12/2/21 I−12 12/2/21 I−5 12/2/21 I−13 12/2/21 I−6 12/2/21 I−7 12/2/21 Back Cover N/A PAGE DATE PCG U−1 6/17/21 PCG V−1 12/2/21 I−1 12/2/21 PCG V−2 12/2/21 I−2 PCG V−3 12/2/21 PCG V−4 12/2/21 PCG W−1 12/2/21 PCG W−2 12/2/21 Checklist of Pages Index I−3 I−4 CK−7 AIM 6/17/21 Aeronautical Information Manual Explanation of Changes Effective: June 17, 2021 a. 1−1−9. INSTRUMENT LANDING SYSTEM (ILS) This change is to edit the following text and add an additional figure to clarify that charted procedures with localizer coverage outside the Standard Service Volume (SSV) have been validated and approved by flight inspection. b. 1−1−13. USER REPORTS REQUESTED ON NAVAID OR GLOBAL NAVIGATION SATELLITE SYSTEM (GNSS) PERFORMANCE OR INTERFERENCE 1−2−4. PILOTS AND AIR TRAFFIC CONTROLLERS RECOGNIZING INTERFERENCE OR SPOOFING The change to paragraph 1−2−4 is a complete rewrite. It was necessary to update information regarding uses and affected systems during GPS outages. The changes to paragraph 1−1−13 incorporate a paragraph title change, a correction to previous paragraph numbering, and a partial rewrite. This will aid in more extensive reporting requests to enable better analysis of outage events. c. 4−1−11. DESIGNATED UNICOM/MULTICOM FREQUENCIES Over the Continental United States and Coastal Waters 123.4 MHz and 123.45 MHz are reserved by the Federal Communications Commission (FCC) for stations individually licensed to commercial aircraft and accessory manufacturers to use as flight test frequencies. Aircraft may only communicate with their associated company ground stations and these frequencies may not be used for air−to−air communications of any sort. In order to bring attention to the proper usage of 123.4 MHz and 123.45 MHz, this change adds these frequencies to TBL 4−1−3, Other Frequency Usage Designated by the FCC, along with the description of their use and the note that they are not for air−to−air communication. Explanation of Changes d. 4−2−3. CONTACT PROCEDURES In order to prevent confusion with the proper use of the frequency 123.4 MHz, this editorial change removes 123.4 as the generic ATC frequency used in this paragraph and the EXAMPLE following the paragraph, and substitutes a different generic ATC frequency. e. 5−1−1. PREFLIGHT PREPARATION 5−1−2. FOLLOW IFR PROCEDURES EVEN WHEN OPERATING VFR 7−1−2. FAA WEATHER SERVICES 7−1−5. PREFLIGHT BRIEFING This change inserts language in the Aeronautical Information Manual that pilots do not need to call Flight Service in order to obtain a regulatory compliant briefing and encourages pilots to self−brief before calling a flight service station. f. 5−4−6. APPROACH CLEARANCE 5−4−9. PROCEDURE TURN AND HOLD− IN−LIEU OF PROCEDURE TURN The proposed change adds subparagraph 5−4−6e8 regarding arrival holding patterns and removes the current note after 5−4−9a5 which currently addresses arrival holding patterns inappropriately as hold−in− lieu of procedure turn. g. 5−4−23. VISUAL APPROACH This change updates Aeronautical Information Manual (AIM) guidance concerning multiple visual approaches to parallel runways at the same airport. h. 6−2−4. EMERGENCY LOCATOR TRANSMITTER (ELT) This change removes reference to the satellite monitoring of ELTs transmitting on 121.5 MHz and 243.0 MHz. This update also focuses on the advantages of ELTs which transmit on 406 MHz. i. 6−4−3. REESTABLISHING RADIO CONTACT 7−1−24. MICROBURSTS This change reflects the removal of the term ARINC and reflects the addition of new communication relay E of Chg−1 AIM call signs due to corporate changes in the company name. j. APPENDIX 2. VOLCANIC ACTIVITY REPORTING FORM (VAR) This change is to replace the out of date Volcanic Activity Reporting Form (VAR) in Appendix 2 with the updated Volcanic Activity Reporting Form (VAR). E of Chg−2 6/17/21 k. Editorial Changes Editorial changes include the deletion of obsolete Low Altitude Alert System (LAAS) content in paragraph 4−1−16, an updated FIG 7−1−14, and updated URL links. Also, outdated references to the National Flight Data Center (NFDC) were removed. l. Entire Publication Additional editorial/format changes were made where necessary. Revision bars were not used because of the insignificant nature of these changes. Explanation of Changes 6/17/21 AIM Subscription Information This and other selected Air Traffic publications are available online: www.faa.gov/air_traffic/publications To Obtain Copies of this Publication General Public * Write: Superintendent of Documents U.S. Government Printing Office P.O. Box 979050 St. Louis, MO 63197−9000 Phone: 202−512−1800 Online: https://bookstore.gpo.gov Government Organizations* This manual will be available on the FAA website by its effective date. All Government organizations are responsible for viewing, downloading, and subscribing to receive electronic mail notifications when changes occur to this manual. Electronic subscription information can be obtained by visiting http://www.faa.gov/air_traffic/publications. *For those desiring printed copies, current pricing is available on the GPO website at http://bookstore.gpo.gov. Subscription Information 6/17/21 AIM Comments/Corrections The office of primary responsibility (OPR) for this manual is: FAA Headquarters, Mission Support Services Policy Directorate (AJV−P) 600 Independence Avenue, SW. Washington, DC 20597 Proposed changes must be submitted electronically, using the following format, to the Policy Directorate Correspondence Mailbox at 9-AJV-P−HQ-Correspondence@faa.gov. Notice to Editor The following comments/corrections are submitted concerning the information contained in: Paragraph number Title Page Dated _________________ Name Street City Comments/Corrections State Zip 6/17/21 AIM Federal Aviation Administration (FAA) The Federal Aviation Administration is responsible for ensuring the safe, efficient, and secure use of the Nation’s airspace, by military as well as civil aviation, for promoting safety in air commerce, for encouraging and developing civil aeronautics, including new aviation technology, and for supporting the requirements of national defense. The activities required to carry out these responsibilities include: safety regulations; airspace management and the establishment, operation, and maintenance of a civil−military common system of air traffic control (ATC) and navigation facilities; research and development in support of the fostering of a national system of airports, promulgation of standards and specifications for civil airports, and administration of Federal grants−in−aid for developing public airports; various joint and cooperative activities with the Department of Defense; and technical assistance (under State Department auspices) to other countries. Aeronautical Information Manual (AIM) Basic Flight Information and ATC Procedures This manual is designed to provide the aviation community with basic flight information and ATC procedures for use in the National Airspace System (NAS) of the United States. An international version called the Aeronautical Information Publication contains parallel information, as well as specific information on the international airports for use by the international community. This manual contains the fundamentals required in order to fly in the United States NAS. It also contains items of interest to pilots concerning health and medical facts, factors affecting flight safety, a pilot/controller glossary of terms used in the ATC System, and information on safety, accident, and hazard reporting. This manual is complemented by other operational publications which are available via separate subscriptions. These publications are: The Chart Supplement U.S., the Chart Supplement Alaska, and the Chart Supplement Pacific − These publications contain information on airports, communications, navigation aids, instrument landing systems, VOR receiver check points, preferred routes, Flight Service Station/Weather Service telephone numbers, Air Route Traffic Control Center (ARTCC) frequencies, part−time surface areas, and various other pertinent special notices essential to air navigation. These publications are available through a network of FAA approved print providers. A listing of products, dates of latest editions, and print providers is available on the Aeronautical Information Services (AIS) website at: http://www.faa.gov/air_traffic/flight_info/aeronav/ print_providers/. Publication Schedule Basic or Change Basic Manual Change 1 Change 2 Change 3 Basic Manual Change 1 Change 2 Change 3 Basic Flight Information and ATC Procedures Cutoff Date for Completion 12/31/20 6/17/21 12/2/21 5/19/22 11/3/22 4/20/23 10/5/23 3/21/24 Effective Date of Publication 6/17/21 12/2/21 5/19/22 11/3/22 4/20/23 10/5/23 3/21/24 9/5/24 6/17/21 AIM Flight Information Publication Policy The following is in essence, the statement issued by the FAA Administrator and published in the December 10, 1964, issue of the Federal Register, concerning the FAA policy as pertaining to the type of information that will be published as NOTAMs and in the Aeronautical Information Manual. a. It is a pilot’s inherent responsibility to be alert at all times for and in anticipation of all circumstances, situations, and conditions affecting the safe operation of the aircraft. For example, a pilot should expect to find air traffic at any time or place. At or near both civil and military airports and in the vicinity of known training areas, a pilot should expect concentrated air traffic and realize concentrations of air traffic are not limited to these places. b. It is the general practice of the agency to advertise by NOTAM or other flight information publications such information it may deem appropriate; information which the agency may from time to time make available to pilots is solely for the purpose of assisting them in executing their regulatory responsibilities. Such information serves the aviation community as a whole and not pilots individually. Flight Information Publication Policy c. The fact that the agency under one particular situation or another may or may not furnish information does not serve as a precedent of the agency’s responsibility to the aviation community; neither does it give assurance that other information of the same or similar nature will be advertised, nor, does it guarantee that any and all information known to the agency will be advertised. d. This publication, while not regulatory, provides information which reflects examples of operating techniques and procedures which may be requirements in other federal publications or regulations. It is made available solely to assist pilots in executing their responsibilities required by other publications. Consistent with the foregoing, it is the policy of the Federal Aviation Administration to furnish information only when, in the opinion of the agency, a unique situation should be advertised and not to furnish routine information such as concentrations of air traffic, either civil or military. The Aeronautical Information Manual will not contain informative items concerning everyday circumstances that pilots should, either by good practices or regulation, expect to encounter or avoid. 6/17/21 AIM Aeronautical Information Manual (AIM) Code of Federal Regulations and Advisory Circulars Code of Federal Regulations - The FAA publishes the Code of Federal Regulations (CFR) to make readily available to the aviation community the regulatory requirements placed upon them. These regulations are sold as individual parts by the Superintendent of Documents. The more frequently amended parts are sold on subscription service with subscribers receiving changes automatically as issued. Less active parts are sold on a single−sale basis. Changes to single-sale parts will be sold separately as issued. Information concerning these changes will be furnished by the FAA through its Status of Federal Aviation Regulations, AC 00−44. Advisory Circulars - The FAA issues Advisory Circulars (AC) to inform the aviation public in a systematic way of nonregulatory material. Unless incorporated into a regulation by reference, the contents of an advisory circular are not binding on the public. Advisory Circulars are issued in a numbered subject system corresponding to the subject areas of the Code of Federal Regulations (CFR) (Title 14, Chapter 1, FAA). AC 00−2, Advisory Circular Checklist and Status of Other FAA Publications, contains advisory circulars that are for sale as well as those distributed free−of−charge by the FAA. Code of Federal Regulations and Advisory Circulars NOTE− The above information relating to CFRs and ACs is extracted from AC 00−2. Many of the CFRs and ACs listed in AC 00−2 are cross−referenced in the AIM. These regulatory and nonregulatory references cover a wide range of subjects and are a source of detailed information of value to the aviation community. AC 00−2 is issued annually and can be obtained free−of−charge from: U.S. Department of Transportation Subsequent Distribution Office Ardmore East Business Center 3341 Q 75th Avenue Landover, MD 20785 Telephone: 301−322−4961 AC 00−2 may also be found at: http://www.faa.gov under Advisory Circulars. External References - All references to Advisory Circulars and other FAA publications in the Aeronautical Information Manual include the FAA Advisory Circular or Order identification numbers (when available). However, due to varied publication dates, the basic publication letter is not included. EXAMPLE− FAA Order JO 7110.65X, Air Traffic Control, is referenced as FAA Order JO 7110.65. 5/19/22 AIM Table of Contents Chapter 1. Air Navigation Section 1. Navigation Aids Paragraph Page 1-1-1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-2. Nondirectional Radio Beacon (NDB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-3. VHF Omni-directional Range (VOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-4. VOR Receiver Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-5. Tactical Air Navigation (TACAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-6. VHF Omni-directional Range/Tactical Air Navigation (VORTAC) . . . . . . . . . 1-1-7. Distance Measuring Equipment (DME) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-8. NAVAID Service Volumes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-9. Instrument Landing System (ILS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-10. Simplified Directional Facility (SDF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-11. NAVAID Identifier Removal During Maintenance . . . . . . . . . . . . . . . . . . . . . . 1-1-12. NAVAIDs with Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-13. User Reports Requested on NAVAID Outages . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-14. LORAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-15. Inertial Reference Unit (IRU), Inertial Navigation System (INS), and Attitude Heading Reference System (AHRS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-16. Doppler Radar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-17. Global Positioning System (GPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-18. Wide Area Augmentation System (WAAS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-19. Ground Based Augmentation System (GBAS) Landing System (GLS) . . . . . . 1-1-20. Precision Approach Systems other than ILS and GLS . . . . . . . . . . . . . . . . . . . . 1-1-1 1-1-1 1-1-1 1-1-3 1-1-4 1-1-5 1-1-5 1-1-5 1-1-10 1-1-16 1-1-18 1-1-18 1-1-18 1-1-19 1-1-19 1-1-19 1-1-20 1-1-32 1-1-36 1-1-38 Section 2. Performance-Based Navigation (PBN) and Area Navigation (RNAV) 1-2-1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-2. Required Navigation Performance (RNP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-3. Use of Suitable Area Navigation (RNAV) Systems on Conventional Procedures and Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-4. Recognizing, Mitigating and Adapting to GPS Interference (Jamming or Spoofing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1 1-2-4 1-2-7 1-2-9 Chapter 2. Aeronautical Lighting and Other Airport Visual Aids Section 1. Airport Lighting Aids 2-1-1. 2-1-2. 2-1-3. 2-1-4. 2-1-5. 2-1-6. 2-1-7. 2-1-8. Approach Light Systems (ALS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Visual Glideslope Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Runway End Identifier Lights (REIL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Runway Edge Light Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . In-runway Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Runway Status Light (RWSL) System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control of Lighting Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pilot Control of Airport Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table of Contents 2-1-1 2-1-1 2-1-6 2-1-6 2-1-6 2-1-7 2-1-9 2-1-9 i AIM 5/19/22 Paragraph Page 2-1-9. Airport/Heliport Beacons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1-10. Taxiway Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1-12 2-1-13 Section 2. Air Navigation and Obstruction Lighting 2-2-1. 2-2-2. 2-2-3. 2-2-4. Aeronautical Light Beacons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code Beacons and Course Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Obstruction Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Lighting Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2-1 2-2-1 2-2-1 2-2-2 Section 3. Airport Marking Aids and Signs 2-3-1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-2. Airport Pavement Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-3. Runway Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-4. Taxiway Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-5. Holding Position Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-6. Other Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-7. Airport Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-8. Mandatory Instruction Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-9. Location Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-10. Direction Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-11. Destination Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-12. Information Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-13. Runway Distance Remaining Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-14. Aircraft Arresting Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-15. Security Identification Display Area (SIDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3-1 2-3-1 2-3-1 2-3-7 2-3-12 2-3-16 2-3-19 2-3-20 2-3-23 2-3-25 2-3-28 2-3-29 2-3-29 2-3-30 2-3-31 Chapter 3. Airspace Section 1. General 3-1-1. 3-1-2. 3-1-3. 3-1-4. 3-1-5. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Dimensions of Airspace Segments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hierarchy of Overlapping Airspace Designations . . . . . . . . . . . . . . . . . . . . . . . . . Basic VFR Weather Minimums . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VFR Cruising Altitudes and Flight Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1-1 3-1-1 3-1-1 3-1-1 3-1-2 Section 2. Controlled Airspace 3-2-1. 3-2-2. 3-2-3. 3-2-4. 3-2-5. 3-2-6. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class A Airspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class B Airspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class C Airspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class D Airspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class E Airspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2-1 3-2-2 3-2-2 3-2-4 3-2-8 3-2-9 Section 3. Class G Airspace 3-3-1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3-2. VFR Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3-3. IFR Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii 3-3-1 3-3-1 3-3-1 Table of Contents 5/19/22 AIM Section 4. Special Use Airspace Paragraph 3-4-1. 3-4-2. 3-4-3. 3-4-4. 3-4-5. 3-4-6. 3-4-7. 3-4-8. 3-4-9. Page General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prohibited Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Restricted Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warning Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Military Operations Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alert Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Controlled Firing Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . National Security Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Obtaining Special Use Airspace Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4-1 3-4-1 3-4-1 3-4-2 3-4-2 3-4-2 3-4-2 3-4-2 3-4-2 Section 5. Other Airspace Areas 3-5-1. 3-5-2. 3-5-3. 3-5-4. 3-5-5. 3-5-6. 3-5-7. 3-5-8. 3-5-9. Airport Advisory/Information Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Military Training Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temporary Flight Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parachute Jump Aircraft Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Published VFR Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Terminal Radar Service Area (TRSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special Air Traffic Rules (SATR) and Special Flight Rules Area (SFRA) . . . . . Weather Reconnaissance Area (WRA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Non-Charted Airspace Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5-1 3-5-1 3-5-2 3-5-5 3-5-5 3-5-9 3-5-9 3-5-9 3-5-10 Chapter 4. Air Traffic Control Section 1. Services Available to Pilots 4-1-1. 4-1-2. 4-1-3. 4-1-4. 4-1-5. Air Route Traffic Control Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Towers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flight Service Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recording and Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communications Release of IFR Aircraft Landing at an Airport Without an Operating Control Tower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-6. Pilot Visits to Air Traffic Facilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-7. Operation Rain Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-8. Approach Control Service for VFR Arriving Aircraft . . . . . . . . . . . . . . . . . . . . . 4-1-9. Traffic Advisory Practices at Airports Without Operating Control Towers . . . . 4-1-10. IFR Approaches/Ground Vehicle Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-11. Designated UNICOM/MULTICOM Frequencies . . . . . . . . . . . . . . . . . . . . . . . 4-1-12. Use of UNICOM for ATC Purposes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-13. Automatic Terminal Information Service (ATIS) . . . . . . . . . . . . . . . . . . . . . . . . 4-1-14. Automatic Flight Information Service (AFIS) - Alaska FSSs Only . . . . . . . . . 4-1-15. Radar Traffic Information Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-16. Safety Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-17. Radar Assistance to VFR Aircraft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-18. Terminal Radar Services for VFR Aircraft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-19. Tower En Route Control (TEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-20. Transponder and ADS-B Out Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-21. Airport Reservation Operations and Special Traffic Management Programs . 4-1-22. Requests for Waivers and Authorizations from Title 14, Code of Federal Regulations (14 CFR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table of Contents 4-1-1 4-1-1 4-1-1 4-1-1 4-1-1 4-1-1 4-1-1 4-1-2 4-1-2 4-1-6 4-1-6 4-1-7 4-1-7 4-1-8 4-1-9 4-1-10 4-1-11 4-1-12 4-1-14 4-1-15 4-1-18 4-1-19 iii AIM 5/19/22 Paragraph Page 4-1-23. Weather Systems Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1-19 Section 2. Radio Communications Phraseology and Techniques 4-2-1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-2. Radio Technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-3. Contact Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-4. Aircraft Call Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-5. Description of Interchange or Leased Aircraft . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-6. Ground Station Call Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-7. Phonetic Alphabet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-8. Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-9. Altitudes and Flight Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-10. Directions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-11. Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-12. Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-13. Communications with Tower when Aircraft Transmitter or Receiver or Both are Inoperative . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-14. Communications for VFR Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2-1 4-2-1 4-2-1 4-2-3 4-2-4 4-2-5 4-2-5 4-2-5 4-2-6 4-2-6 4-2-6 4-2-6 4-2-7 4-2-7 Section 3. Airport Operations 4-3-1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-2. Airports with an Operating Control Tower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-3. Traffic Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-4. Visual Indicators at Airports Without an Operating Control Tower . . . . . . . . . . 4-3-5. Unexpected Maneuvers in the Airport Traffic Pattern . . . . . . . . . . . . . . . . . . . . . 4-3-6. Use of Runways/Declared Distances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-7. Low Level Wind Shear/Microburst Detection Systems . . . . . . . . . . . . . . . . . . . . 4-3-8. Braking Action Reports and Advisories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-9. Runway Condition Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-10. Intersection Takeoffs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-11. Pilot Responsibilities When Conducting Land and Hold Short Operations (LAHSO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-12. Low Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-13. Traffic Control Light Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-14. Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-15. Gate Holding Due to Departure Delays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-16. VFR Flights in Terminal Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-17. VFR Helicopter Operations at Controlled Airports . . . . . . . . . . . . . . . . . . . . . . 4-3-18. Taxiing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-19. Taxi During Low Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-20. Exiting the Runway After Landing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-21. Practice Instrument Approaches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-22. Option Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-23. Use of Aircraft Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-24. Flight Inspection/`Flight Check' Aircraft in Terminal Areas . . . . . . . . . . . . . . . 4-3-25. Hand Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3-26. Operations at Uncontrolled Airports With Automated Surface Observing System (ASOS)/Automated Weather Observing System (AWOS) . . . . . . . . . . iv 4-3-1 4-3-1 4-3-2 4-3-7 4-3-7 4-3-8 4-3-13 4-3-13 4-3-14 4-3-16 4-3-16 4-3-19 4-3-19 4-3-20 4-3-21 4-3-21 4-3-21 4-3-23 4-3-24 4-3-25 4-3-25 4-3-26 4-3-27 4-3-28 4-3-28 4-3-31 Table of Contents 5/19/22 AIM Section 4. ATC Clearances and Aircraft Separation Paragraph Page 4-4-1. Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-2. Clearance Prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-3. Clearance Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-4. Amended Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-5. Coded Departure Route (CDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-6. Special VFR Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-7. Pilot Responsibility upon Clearance Issuance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-8. IFR Clearance VFR-on-top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-9. VFR/IFR Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-10. Adherence to Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-11. IFR Separation Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-12. Speed Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-13. Runway Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-14. Visual Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-15. Use of Visual Clearing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-16. Traffic Alert and Collision Avoidance System (TCAS I & II) . . . . . . . . . . . . . . 4-4-17. Traffic Information Service (TIS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4-1 4-4-1 4-4-1 4-4-2 4-4-3 4-4-3 4-4-4 4-4-4 4-4-5 4-4-5 4-4-7 4-4-7 4-4-10 4-4-10 4-4-11 4-4-11 4-4-12 Section 5. Surveillance Systems 4-5-1. 4-5-2. 4-5-3. 4-5-4. 4-5-5. Radar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Traffic Control Radar Beacon System (ATCRBS) . . . . . . . . . . . . . . . . . . . . . Surveillance Radar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Precision Approach Radar (PAR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Airport Surface Detection Equipment (ASDE-X)/Airport Surface Surveillance Capability (ASSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5-6. Traffic Information Service (TIS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5-7. Automatic Dependent Surveillance-Broadcast (ADS-B) Services . . . . . . . . . 4-5-8. Traffic Information Service- Broadcast (TIS-B) . . . . . . . . . . . . . . . . . . . . . . . . 4-5-9. Flight Information Service- Broadcast (FIS-B) . . . . . . . . . . . . . . . . . . . . . . . . . 4-5-10. Automatic Dependent Surveillance-Rebroadcast (ADS-R) . . . . . . . . . . . . . . 4-5-1 4-5-2 4-5-7 4-5-7 4-5-7 4-5-8 4-5-14 4-5-19 4-5-20 4-5-22 Section 6. Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4-6-1. Applicability and RVSM Mandate (Date/Time and Area) . . . . . . . . . . . . . . . . . 4-6-2. Flight Level Orientation Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6-3. Aircraft and Operator Approval Policy/Procedures, RVSM Monitoring and Databases for Aircraft and Operator Approval . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6-4. Flight Planning into RVSM Airspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6-5. Pilot RVSM Operating Practices and Procedures . . . . . . . . . . . . . . . . . . . . . . . . . 4-6-6. Guidance on Severe Turbulence and Mountain Wave Activity (MWA) . . . . . . . 4-6-7. Guidance on Wake Turbulence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6-8. Pilot/Controller Phraseology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6-9. Contingency Actions: Weather Encounters and Aircraft System Failures that Occur After Entry into RVSM Airspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6-10. Procedures for Accommodation of Non-RVSM Aircraft . . . . . . . . . . . . . . . . . 4-6-11. Non-RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off . . . . . . . . . . . . . . . . . Table of Contents 4-6-1 4-6-1 4-6-1 4-6-2 4-6-3 4-6-3 4-6-5 4-6-5 4-6-6 4-6-8 4-6-9 v AIM 5/19/22 Section 7. Operational Policy/Procedures for the Gulf of Mexico 50 NM Lateral Separation Initiative Paragraph 4-7-1. 4-7-2. 4-7-3. 4-7-4. 4-7-5. 4-7-6. Page Introduction and General Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accommodating Non-RNP 10 Aircraft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Obtaining RNP 10 or RNP 4 Operational Authorization . . . . . . . . . . . . . . . . . . . Authority for Operations with a Single Long-Range Navigation System . . . . . Flight Plan Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contingency Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7-1 4-7-1 4-7-1 4-7-2 4-7-2 4-7-2 Chapter 5. Air Traffic Procedures Section 1. Preflight 5-1-1. Preflight Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-2. Follow IFR Procedures Even When Operating VFR . . . . . . . . . . . . . . . . . . . . . . 5-1-3. Notice to Air Missions (NOTAM) System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-4. Operational Information System (OIS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-5. Flight Plan - VFR Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-6. Flight Plan - IFR Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-7. Flight Plans For Military/DOD Use Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-8. Flight Plan – Defense VFR (DVFR) Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-9. Single Flights Conducted With Both VFR and IFR Flight Plans . . . . . . . . . . . . 5-1-10. IFR Operations to High Altitude Destinations . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-11. Flights Outside U.S. Territorial Airspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-12. Change in Flight Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-13. Change in Proposed Departure Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-14. Closing VFR/DVFR Flight Plans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-15. Canceling IFR Flight Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-16. RNAV and RNP Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-17. Cold Temperature Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1-1 5-1-2 5-1-3 5-1-8 5-1-9 5-1-10 5-1-14 5-1-14 5-1-14 5-1-14 5-1-15 5-1-16 5-1-16 5-1-16 5-1-16 5-1-17 5-1-18 Section 2. Departure Procedures 5-2-1. 5-2-2. 5-2-3. 5-2-4. 5-2-5. 5-2-6. 5-2-7. Pre‐taxi Clearance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automated Pre-Departure Clearance Procedures . . . . . . . . . . . . . . . . . . . . . . . . IFR Clearances Off Uncontrolled Airports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Taxi Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Line Up and Wait (LUAW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Abbreviated IFR Departure Clearance (Cleared. . .as Filed) Procedures . . . . . Departure Restrictions, Clearance Void Times, Hold for Release, and Release Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2-8. Departure Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2-9. Instrument Departure Procedures (DP) - Obstacle Departure Procedures (ODP), Standard Instrument Departures (SID), and Diverse Vector Areas (DVA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2-1 5-2-1 5-2-2 5-2-2 5-2-2 5-2-3 5-2-4 5-2-5 5-2-6 Section 3. En Route Procedures 5-3-1. 5-3-2. 5-3-3. 5-3-4. vi ARTCC Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Position Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additional Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Airways and Route Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3-1 5-3-14 5-3-15 5-3-16 Table of Contents 5/19/22 AIM Paragraph 5-3-5. 5-3-6. 5-3-7. 5-3-8. Page Airway or Route Course Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changeover Points (COPs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Minimum Turning Altitude (MTA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Holding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3-18 5-3-19 5-3-19 5-3-19 Section 4. Arrival Procedures 5-4-1. Standard Terminal Arrival (STAR) Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-2. Local Flow Traffic Management Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-3. Approach Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-4. Advance Information on Instrument Approach . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-5. Instrument Approach Procedure (IAP) Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-6. Approach Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-7. Instrument Approach Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-8. Special Instrument Approach Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-9. Procedure Turn and Hold-in-lieu of Procedure Turn . . . . . . . . . . . . . . . . . . . . 5-4-10. Timed Approaches from a Holding Fix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-11. Radar Approaches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-12. Radar Monitoring of Instrument Approaches . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-13. Simultaneous Approaches to Parallel Runways . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-14. Simultaneous Dependent Approaches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-15. Simultaneous Independent ILS/RNAV/GLS Approaches . . . . . . . . . . . . . . . . . 5-4-16. Simultaneous Close Parallel PRM Approaches and Simultaneous Offset Instrument Approaches (SOIA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-17. Simultaneous Converging Instrument Approaches . . . . . . . . . . . . . . . . . . . . . . . 5-4-18. RNP AR (Authorization Required) Instrument Procedures . . . . . . . . . . . . . . . 5-4-19. Side-step Maneuver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-20. Approach and Landing Minimums . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-21. Missed Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-22. Use of Enhanced Flight Vision Systems (EFVS) on Instrument Approaches . 5-4-23. Visual Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-24. Charted Visual Flight Procedure (CVFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-25. Contact Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-26. Landing Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-27. Overhead Approach Maneuver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4-1 5-4-3 5-4-3 5-4-4 5-4-5 5-4-25 5-4-27 5-4-29 5-4-30 5-4-33 5-4-35 5-4-36 5-4-37 5-4-39 5-4-41 5-4-43 5-4-50 5-4-50 5-4-51 5-4-52 5-4-55 5-4-57 5-4-61 5-4-62 5-4-62 5-4-63 5-4-63 Section 5. Pilot/Controller Roles and Responsibilities 5-5-1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-2. Air Traffic Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-3. Contact Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-4. Instrument Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-5. Missed Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-6. Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-7. Safety Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-8. See and Avoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-9. Speed Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-10. Traffic Advisories (Traffic Information) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-11. Visual Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-12. Visual Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-13. VFR‐on‐top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-14. Instrument Departures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table of Contents 5-5-1 5-5-1 5-5-2 5-5-2 5-5-3 5-5-3 5-5-4 5-5-4 5-5-4 5-5-5 5-5-5 5-5-6 5-5-6 5-5-7 vii AIM 5/19/22 Paragraph Page 5-5-15. Minimum Fuel Advisory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-16. RNAV and RNP Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5-7 5-5-8 Section 6. National Security and Interception Procedures 5-6-1. National Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-2. National Security Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-3. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-4. ADIZ Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-5. Civil Aircraft Operations To or From U.S. Territorial Airspace . . . . . . . . . . . . . 5-6-6. Civil Aircraft Operations Within U.S. Territorial Airspace . . . . . . . . . . . . . . . . . 5-6-7. Civil Aircraft Operations Transiting U.S. Territorial Airspace . . . . . . . . . . . . . . 5-6-8. Foreign State Aircraft Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-9. FAA/TSA Airspace Waivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-10. TSA Aviation Security Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-11. FAA Flight Routing Authorizations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-12. Emergency Security Control of Air Traffic (ESCAT) . . . . . . . . . . . . . . . . . . . . . 5-6-13. Interception Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-14. Law Enforcement Operations by Civil and Military Organizations . . . . . . . . . 5-6-15. Interception Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-16. ADIZ Boundaries and Designated Mountainous Areas . . . . . . . . . . . . . . . . . . 5-6-17. Visual Warning System (VWS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6-1 5-6-1 5-6-1 5-6-2 5-6-3 5-6-4 5-6-5 5-6-6 5-6-7 5-6-7 5-6-7 5-6-7 5-6-8 5-6-10 5-6-11 5-6-13 5-6-14 Chapter 6. Emergency Procedures Section 1. General 6-1-1. Pilot Responsibility and Authority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1-2. Emergency Condition- Request Assistance Immediately . . . . . . . . . . . . . . . . . . 6-1-1 6-1-1 Section 2. Emergency Services Available to Pilots 6-2-1. 6-2-2. 6-2-3. 6-2-4. 6-2-5. 6-2-6. Radar Service for VFR Aircraft in Difficulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transponder Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intercept and Escort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency Locator Transmitter (ELT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FAA K-9 Explosives Detection Team Program . . . . . . . . . . . . . . . . . . . . . . . . . . Search and Rescue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2-1 6-2-1 6-2-1 6-2-2 6-2-3 6-2-4 Section 3. Distress and Urgency Procedures 6-3-1. 6-3-2. 6-3-3. 6-3-4. 6-3-5. Distress and Urgency Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Obtaining Emergency Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ditching Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special Emergency (Air Piracy) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel Dumping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3-1 6-3-1 6-3-3 6-3-6 6-3-7 Section 4. Two‐way Radio Communications Failure 6-4-1. Two‐way Radio Communications Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4-2. Transponder Operation During Two‐way Communications Failure . . . . . . . . . . 6-4-3. Reestablishing Radio Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii 6-4-1 6-4-2 6-4-2 Table of Contents 5/19/22 AIM Section 5. Aircraft Rescue and Fire Fighting Communications Paragraph Page 6-5-1. Discrete Emergency Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5-2. Radio Call Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5-3. ARFF Emergency Hand Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5-1 6-5-1 6-5-1 Chapter 7. Safety of Flight Section 1. Meteorology 7-1-1. National Weather Service Aviation Weather Service Program . . . . . . . . . . . . . . 7-1-2. FAA Weather Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-3. Use of Aviation Weather Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-4. Graphical Forecasts for Aviation (GFA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-5. Preflight Briefing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-6. Inflight Aviation Weather Advisories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-7. Categorical Outlooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-8. Inflight Weather Advisory Broadcasts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-9. Flight Information Services (FIS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-10. Weather Observing Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-11. Weather Radar Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-12. ATC Inflight Weather Avoidance Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-13. Runway Visual Range (RVR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-14. Reporting of Cloud Heights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-15. Reporting Prevailing Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-16. Estimating Intensity of Rain and Ice Pellets . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-17. Estimating Intensity of Snow or Drizzle (Based on Visibility) . . . . . . . . . . . . . . 7-1-18. Pilot Weather Reports (PIREPs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-19. PIREPs Relating to Airframe Icing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-20. Definitions of Inflight Icing Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-21. PIREPs Relating to Turbulence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-22. Wind Shear PIREPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-23. Clear Air Turbulence (CAT) PIREPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-24. Microbursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-25. PIREPs Relating to Volcanic Ash Activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-26. Thunderstorms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-27. Thunderstorm Flying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-28. Key to Aerodrome Forecast (TAF) and Aviation Routine Weather Report (METAR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1-29. International Civil Aviation Organization (ICAO) Weather Formats . . . . . . . 7-1-1 7-1-2 7-1-3 7-1-6 7-1-8 7-1-11 7-1-18 7-1-18 7-1-20 7-1-24 7-1-32 7-1-36 7-1-37 7-1-39 7-1-39 7-1-39 7-1-40 7-1-40 7-1-41 7-1-42 7-1-45 7-1-46 7-1-46 7-1-46 7-1-57 7-1-57 7-1-58 7-1-60 7-1-62 Section 2. Barometric Altimeter Errors and Setting Procedures 7-2-1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2-2. Barometric Pressure Altimeter Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2-3. Altimeter Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2-1 7-2-1 7-2-1 Section 3. Cold Temperature Barometric Altimeter Errors, Setting Procedures and Cold Temperature Airports (CTA) 7-3-1. Effect of Cold Temperature on Barometric Altimeters . . . . . . . . . . . . . . . . . . . . 7-3-2. Pre-Flight Planning for Cold Temperature Altimeter Errors . . . . . . . . . . . . . . . Table of Contents 7-3-1 7-3-1 ix AIM 5/19/22 Paragraph Page 7-3-3. Effects of Cold Temperature on Baro-Vertical Navigation (VNAV) Vertical Guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3-4. Cold Temperature Airports (CTA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3-5. Cold Temperature Airport Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3-6. Examples for Calculating Altitude Corrections on CTAs . . . . . . . . . . . . . . . . . . . 7-3-1 7-3-2 7-3-3 7-3-6 Section 4. Wake Turbulence 7-4-1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-2. Vortex Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-3. Vortex Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-4. Vortex Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-5. Operations Problem Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-6. Vortex Avoidance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-7. Helicopters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-8. Pilot Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-9. Air Traffic Wake Turbulence Separations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-10. Development and New Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4-1 7-4-1 7-4-1 7-4-2 7-4-4 7-4-5 7-4-6 7-4-6 7-4-7 7-4-8 Section 5. Bird Hazards and Flight Over National Refuges, Parks, and Forests 7-5-1. 7-5-2. 7-5-3. 7-5-4. 7-5-5. 7-5-6. Migratory Bird Activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reducing Bird Strike Risks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reporting Bird Strikes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reporting Bird and Other Wildlife Activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pilot Advisories on Bird and Other Wildlife Hazards . . . . . . . . . . . . . . . . . . . . . . Flights Over Charted U.S. Wildlife Refuges, Parks, and Forest Service Areas . 7-5-1 7-5-1 7-5-1 7-5-1 7-5-2 7-5-2 Section 6. Potential Flight Hazards 7-6-1. Accident Cause Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-2. Reporting Radio/Radar Altimeter Anomalies . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-3. VFR in Congested Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-4. Obstructions To Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-5. Avoid Flight Beneath Unmanned Balloons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-6. Unmanned Aircraft Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-7. Mountain Flying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-8. Use of Runway Half-way Signs at Unimproved Airports . . . . . . . . . . . . . . . . . . 7-6-9. Seaplane Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-10. Flight Operations in Volcanic Ash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-11. Emergency Airborne Inspection of Other Aircraft . . . . . . . . . . . . . . . . . . . . . . . 7-6-12. Precipitation Static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-13. Light Amplification by Stimulated Emission of Radiation (Laser) Operations and Reporting Illumination of Aircraft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-14. Flying in Flat Light, Brown Out Conditions, and White Out Conditions . . . . 7-6-15. Operations in Ground Icing Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-16. Avoid Flight in the Vicinity of Exhaust Plumes (Smoke Stacks and Cooling Towers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-17. Space Launch and Reentry Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6-1 7-6-1 7-6-2 7-6-2 7-6-3 7-6-3 7-6-4 7-6-6 7-6-6 7-6-8 7-6-9 7-6-9 7-6-10 7-6-11 7-6-13 7-6-14 7-6-15 Section 7. Safety, Accident, and Hazard Reports 7-7-1. Aviation Safety Reporting Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x 7-7-1 Table of Contents 5/19/22 AIM Paragraph 7-7-2. 7-7-3. 7-7-4. 7-7-5. Page Aircraft Accident and Incident Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Near Midair Collision Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unidentified Flying Object (UFO) Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Alerts For Operators (SAFO) and Information For Operators (InFO) . 7-7-1 7-7-2 7-7-3 7-7-3 Chapter 8. Medical Facts for Pilots Section 1. Fitness for Flight 8-1-1. 8-1-2. 8-1-3. 8-1-4. 8-1-5. 8-1-6. 8-1-7. 8-1-8. Fitness For Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Effects of Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hyperventilation in Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Carbon Monoxide Poisoning in Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Illusions in Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vision in Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aerobatic Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Judgment Aspects of Collision Avoidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1-1 8-1-3 8-1-5 8-1-5 8-1-5 8-1-6 8-1-8 8-1-8 Chapter 9. Aeronautical Charts and Related Publications Section 1. Types of Charts Available 9-1-1. 9-1-2. 9-1-3. 9-1-4. 9-1-5. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Obtaining Aeronautical Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Selected Charts and Products Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Description of Each Chart Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Where and How to Get Charts of Foreign Areas . . . . . . . . . . . . . . . . . . . . . . . . . 9-1-1 9-1-1 9-1-1 9-1-1 9-1-13 Chapter 10. Helicopter Operations Section 1. Helicopter IFR Operations 10-1-1. 10-1-2. 10-1-3. 10-1-4. 10-1-5. Helicopter Flight Control Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Helicopter Instrument Approaches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Helicopter Approach Procedures to VFR Heliports . . . . . . . . . . . . . . . . . . . . . . The Gulf of Mexico Grid System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Departure Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1-1 10-1-2 10-1-4 10-1-5 10-1-6 Section 2. Special Operations 10-2-1. 10-2-2. 10-2-3. 10-2-4. Offshore Helicopter Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Helicopter Night VFR Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Landing Zone Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency Medical Service (EMS) Multiple Helicopter Operations . . . . . . . . 10-2-1 10-2-7 10-2-10 10-2-16 Appendices Appendix Appendix Appendix Appendix 1. Bird/Other Wildlife Strike Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Volcanic Activity Reporting Form (VAR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Abbreviations/Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. FAA Form 7233-4 - International Flight Plan . . . . . . . . . . . . . . . . . . . . . . . Table of Contents Appendix Appendix Appendix Appendix 1-1 2-1 3-1 4-1 xi AIM Paragraph xii 5/19/22 Page Appendix 5. FAA Form 7233-1 - Flight Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 5-1 PILOT/CONTROLLER GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCG-1 I-1 Table of Contents 6/17/21 AIM Chapter 1. Air Navigation Section 1. Navigation Aids 1−1−1. General a. Various types of air navigation aids are in use today, each serving a special purpose. These aids have varied owners and operators, namely: the Federal Aviation Administration (FAA), the military services, private organizations, individual states and foreign governments. The FAA has the statutory authority to establish, operate, maintain air navigation facilities and to prescribe standards for the operation of any of these aids which are used for instrument flight in federally controlled airspace. These aids are tabulated in the Chart Supplement U.S. b. Pilots should be aware of the possibility of momentary erroneous indications on cockpit displays when the primary signal generator for a ground− based navigational transmitter (for example, a glideslope, VOR, or nondirectional beacon) is inoperative. Pilots should disregard any navigation indication, regardless of its apparent validity, if the particular transmitter was identified by NOTAM or otherwise as unusable or inoperative. 1−1−2. Nondirectional Radio Beacon (NDB) a. A low or medium frequency radio beacon transmits nondirectional signals whereby the pilot of an aircraft properly equipped can determine bearings and “home” on the station. These facilities normally operate in a frequency band of 190 to 535 kilohertz (kHz), according to ICAO Annex 10 the frequency range for NDBs is between 190 and 1750 kHz, and transmit a continuous carrier with either 400 or 1020 hertz (Hz) modulation. All radio beacons except the compass locators transmit a continuous three−letter identification in code except during voice transmissions. b. When a radio beacon is used in conjunction with the Instrument Landing System markers, it is called a Compass Locator. c. Voice transmissions are made on radio beacons unless the letter “W” (without voice) is included in the class designator (HW). Navigation Aids d. Radio beacons are subject to disturbances that may result in erroneous bearing information. Such disturbances result from such factors as lightning, precipitation static, etc. At night, radio beacons are vulnerable to interference from distant stations. Nearly all disturbances which affect the Automatic Direction Finder (ADF) bearing also affect the facility’s identification. Noisy identification usually occurs when the ADF needle is erratic. Voice, music or erroneous identification may be heard when a steady false bearing is being displayed. Since ADF receivers do not have a “flag” to warn the pilot when erroneous bearing information is being displayed, the pilot should continuously monitor the NDB’s identification. 1−1−3. VHF Omni−directional Range (VOR) a. VORs operate within the 108.0 to 117.95 MHz frequency band and have a power output necessary to provide coverage within their assigned operational service volume. They are subject to line−of−sight restrictions, and the range varies proportionally to the altitude of the receiving equipment. NOTE− Normal service ranges for the various classes of VORs are given in Navigational Aid (NAVAID) Service Volumes, Paragraph 1−1−8. b. Most VORs are equipped for voice transmission on the VOR frequency. VORs without voice capability are indicated by the letter “W” (without voice) included in the class designator (VORW). c. The only positive method of identifying a VOR is by its Morse Code identification or by the recorded automatic voice identification which is always indicated by use of the word “VOR” following the range’s name. Reliance on determining the identification of an omnirange should never be placed on listening to voice transmissions by the Flight Service Station (FSS) (or approach control facility) involved. Many FSSs remotely operate several omniranges with different names. In some cases, none of the VORs have the name of the “parent” FSS. During periods of maintenance, the facility may radiate a T−E−S−T code (- -) or the code may be 1−1−1 AIM removed. Some VOR equipment decodes the identifier and displays it to the pilot for verification to charts, while other equipment simply displays the expected identifier from a database to aid in verification to the audio tones. You should be familiar with your equipment and use it appropriately. If your equipment automatically decodes the identifier, it is not necessary to listen to the audio identification. d. Voice identification has been added to numerous VORs. The transmission consists of a voice announcement, “AIRVILLE VOR” alternating with the usual Morse Code identification. e. The effectiveness of the VOR depends upon proper use and adjustment of both ground and airborne equipment. 1. Accuracy. The accuracy of course alignment of the VOR is excellent, being generally plus or minus 1 degree. 2. Roughness. On some VORs, minor course roughness may be observed, evidenced by course needle or brief flag alarm activity (some receivers are more susceptible to these irregularities than others). At a few stations, usually in mountainous terrain, the pilot may occasionally observe a brief course needle oscillation, similar to the indication of “approaching station.” Pilots flying over unfamiliar routes are cautioned to be on the alert for these vagaries, and in particular, to use the “to/from” indicator to determine positive station passage. (a) Certain propeller revolutions per minute (RPM) settings or helicopter rotor speeds can cause the VOR Course Deviation Indicator to fluctuate as much as plus or minus six degrees. Slight changes to the RPM setting will normally smooth out this roughness. Pilots are urged to check for this modulation phenomenon prior to reporting a VOR station or aircraft equipment for unsatisfactory operation. f. The VOR Minimum Operational Network (MON). As flight procedures and route structure based on VORs are gradually being replaced with Performance−Based Navigation (PBN) procedures, the FAA is removing selected VORs from service. PBN procedures are primarily enabled by GPS and its augmentation systems, collectively referred to as Global Navigation Satellite System (GNSS). Aircraft that carry DME/DME equipment can also use RNAV which provides a backup to continue flying PBN 1−1−2 6/17/21 during a GNSS disruption. For those aircraft that do not carry DME/DME, the FAA is retaining a limited network of VORs, called the VOR MON, to provide a basic conventional navigation service for operators to use if GNSS becomes unavailable. During a GNSS disruption, the MON will enable aircraft to navigate through the affected area or to a safe landing at a MON airport without reliance on GNSS. Navigation using the MON will not be as efficient as the new PBN route structure, but use of the MON will provide nearly continuous VOR signal coverage at 5,000 feet AGL across the NAS, outside of the Western U.S. Mountainous Area (WUSMA). NOTE− There is no plan to change the NAVAID and route structure in the WUSMA. The VOR MON has been retained principally for IFR aircraft that are not equipped with DME/DME avionics. However, VFR aircraft may use the MON as desired. Aircraft equipped with DME/DME navigation systems would, in most cases, use DME/DME to continue flight using RNAV to their destination. However, these aircraft may, of course, use the MON. 1. Distance to a MON airport. The VOR MON will ensure that regardless of an aircraft’s position in the contiguous United States (CONUS), a MON airport (equipped with legacy ILS or VOR approaches) will be within 100 nautical miles. These airports are referred to as “MON airports” and will have an ILS approach or a VOR approach if an ILS is not available. VORs to support these approaches will be retained in the VOR MON. MON airports are charted on low−altitude en route charts and are contained in the Chart Supplement U.S. and other appropriate publications. NOTE− Any suitable airport can be used to land in the event of a VOR outage. For example, an airport with a DME−required ILS approach may be available and could be used by aircraft that are equipped with DME. The intent of the MON airport is to provide an approach that can be used by aircraft without ADF or DME when radar may not be available. 2. Navigating to an airport. The VOR MON will retain sufficient VORs and increase VOR service volume to ensure that pilots will have nearly continuous signal reception of a VOR when flying at 5,000 feet AGL. A key concept of the MON is to ensure that an aircraft will always be within 100 NM Navigation Aids 6/17/21 of an airport with an instrument approach that is not dependent on GPS. (See paragraph 1−1−8.) If the pilot encounters a GPS outage, the pilot will be able to proceed via VOR−to−VOR navigation at 5,000 feet AGL through the GPS outage area or to a safe landing at a MON airport or another suitable airport, as appropriate. Nearly all VORs inside of the WUSMA and outside the CONUS are being retained. In these areas, pilots use the existing (Victor and Jet) route structure and VORs to proceed through a GPS outage or to a landing. 3. Using the VOR MON. (a) In the case of a planned GPS outage (for example, one that is in a published NOTAM), pilots may plan to fly through the outage using the MON as appropriate and as cleared by ATC. Similarly, aircraft not equipped with GPS may plan to fly and land using the MON, as appropriate and as cleared by ATC. NOTE− In many cases, flying using the MON may involve a more circuitous route than flying GPS−enabled RNAV. (b) In the case of an unscheduled GPS outage, pilots and ATC will need to coordinate the best outcome for all aircraft. It is possible that a GPS outage could be disruptive, causing high workload and demand for ATC service. Generally, the VOR MON concept will enable pilots to navigate through the GPS outage or land at a MON airport or at another airport that may have an appropriate approach or may be in visual conditions. (1) The VOR MON is a reversionary service provided by the FAA for use by aircraft that are unable to continue RNAV during a GPS disruption. The FAA has not mandated that preflight or inflight planning include provisions for GPS− or WAAS−equipped aircraft to carry sufficient fuel to proceed to a MON airport in case of an unforeseen GPS outage. Specifically, flying to a MON airport as a filed alternate will not be explicitly required. Of course, consideration for the possibility of a GPS outage is prudent during flight planning as is maintaining proficiency with VOR navigation. (2) Also, in case of a GPS outage, pilots may coordinate with ATC and elect to continue through the outage or land. The VOR MON is designed to ensure that an aircraft is within 100 NM of an airport, but pilots may decide to proceed to any appropriate airport where a landing can be made. Navigation Aids AIM WAAS users flying under Part 91 are not required to carry VOR avionics. These users do not have the ability or requirement to use the VOR MON. Prudent flight planning, by these WAAS−only aircraft, should consider the possibility of a GPS outage. NOTE− The FAA recognizes that non−GPS−based approaches will be reduced when VORs are eliminated, and that most airports with an instrument approach may only have GPS− or WAAS−based approaches. Pilots flying GPS− or WAAS−equipped aircraft that also have VOR/ILS avionics should be diligent to maintain proficiency in VOR and ILS approaches in the event of a GPS outage. 1−1−4. VOR Receiver Check a. The FAA VOR test facility (VOT) transmits a test signal which provides users a convenient means to determine the operational status and accuracy of a VOR receiver while on the ground where a VOT is located. The airborne use of VOT is permitted; however, its use is strictly limited to those areas/altitudes specifically authorized in the Chart Supplement U.S. or appropriate supplement. b. To use the VOT service, tune in the VOT frequency on your VOR receiver. With the Course Deviation Indicator (CDI) centered, the omni−bearing selector should read 0 degrees with the to/from indication showing “from” or the omni−bearing selector should read 180 degrees with the to/from indication showing “to.” Should the VOR receiver operate an RMI (Radio Magnetic Indicator), it will indicate 180 degrees on any omni−bearing selector (OBS) setting. Two means of identification are used. One is a series of dots and the other is a continuous tone. Information concerning an individual test signal can be obtained from the local FSS. c. Periodic VOR receiver calibration is most important. If a receiver’s Automatic Gain Control or modulation circuit deteriorates, it is possible for it to display acceptable accuracy and sensitivity close into the VOR or VOT and display out−of−tolerance readings when located at greater distances where weaker signal areas exist. The likelihood of this deterioration varies between receivers, and is generally considered a function of time. The best assurance of having an accurate receiver is periodic calibration. Yearly intervals are recommended at which time an authorized repair facility should recalibrate the receiver to the manufacturer’s specifications. 1−1−3 AIM 6/17/21 d. Federal Aviation Regulations (14 CFR Section 91.171) provides for certain VOR equipment accuracy checks prior to flight under instrument flight rules. To comply with this requirement and to ensure satisfactory operation of the airborne system, the FAA has provided pilots with the following means of checking VOR receiver accuracy: 1. VOT or a radiated test signal from an appropriately rated radio repair station. 2. Certified airborne checkpoints and airways. 3. Certified checkpoints on the airport surface. 4. If an airborne checkpoint is not available, select an established VOR airway. Select a prominent ground point, preferably more than 20 NM from the VOR ground facility and maneuver the aircraft directly over the point at a reasonably low altitude above terrain and obstructions. e. A radiated VOT from an appropriately rated radio repair station serves the same purpose as an FAA VOR signal and the check is made in much the same manner as a VOT with the following differences: 1. The frequency normally approved by the Federal Communications Commission is 108.0 MHz. 2. Repair stations are not permitted to radiate the VOR test signal continuously; consequently, the owner or operator must make arrangements with the repair station to have the test signal transmitted. This service is not provided by all radio repair stations. The aircraft owner or operator must determine which repair station in the local area provides this service. A representative of the repair station must make an entry into the aircraft logbook or other permanent record certifying to the radial accuracy and the date of transmission. The owner, operator or representative of the repair station may accomplish the necessary checks in the aircraft and make a logbook entry stating the results. It is necessary to verify which test radial is being transmitted and whether you should get a “to” or “from” indication. f. Airborne and ground check points consist of certified radials that should be received at specific points on the airport surface or over specific landmarks while airborne in the immediate vicinity of the airport. 1−1−4 1. Should an error in excess of plus or minus 4 degrees be indicated through use of a ground check, or plus or minus 6 degrees using the airborne check, Instrument Flight Rules (IFR) flight must not be attempted without first correcting the source of the error. CAUTION− No correction other than the correction card figures supplied by the manufacturer should be applied in making these VOR receiver checks. 2. Locations of airborne check points, ground check points and VOTs are published in the Chart Supplement U.S. 3. If a dual system VOR (units independent of each other except for the antenna) is installed in the aircraft, one system may be checked against the other. Turn both systems to the same VOR ground facility and note the indicated bearing to that station. The maximum permissible variations between the two indicated bearings is 4 degrees. 1−1−5. Tactical Air Navigation (TACAN) a. For reasons peculiar to military or naval operations (unusual siting conditions, the pitching and rolling of a naval vessel, etc.) the civil VOR/Distance Measuring Equipment (DME) system of air navigation was considered unsuitable for military or naval use. A new navigational system, TACAN, was therefore developed by the military and naval forces to more readily lend itself to military and naval requirements. As a result, the FAA has integrated TACAN facilities with the civil VOR/ DME program. Although the theoretical, or technical principles of operation of TACAN equipment are quite different from those of VOR/DME facilities, the end result, as far as the navigating pilot is concerned, is the same. These integrated facilities are called VORTACs. b. TACAN ground equipment consists of either a fixed or mobile transmitting unit. The airborne unit in conjunction with the ground unit reduces the transmitted signal to a visual presentation of both azimuth and distance information. TACAN is a pulse system and operates in the Ultrahigh Frequency (UHF) band of frequencies. Its use requires TACAN airborne equipment and does not operate through conventional VOR equipment. Navigation Aids 6/17/21 AIM 1−1−6. VHF Omni−directional Range/Tactical Air Navigation (VORTAC) automatically, while aircraft equipped with VOR must have a separate DME airborne unit. a. A VORTAC is a facility consisting of two components, VOR and TACAN, which provides three individual services: VOR azimuth, TACAN azimuth and TACAN distance (DME) at one site. Although consisting of more than one component, incorporating more than one operating frequency, and using more than one antenna system, a VORTAC is considered to be a unified navigational aid. Both components of a VORTAC are envisioned as operating simultaneously and providing the three services at all times. d. VOR/DME, VORTAC, Instrument Landing System (ILS)/DME, and localizer (LOC)/DME navigation facilities established by the FAA provide course and distance information from collocated components under a frequency pairing plan. Aircraft receiving equipment which provides for automatic DME selection assures reception of azimuth and distance information from a common source when designated VOR/DME, VORTAC, ILS/DME, and LOC/DME are selected. b. Transmitted signals of VOR and TACAN are each identified by three−letter code transmission and are interlocked so that pilots using VOR azimuth with TACAN distance can be assured that both signals being received are definitely from the same ground station. The frequency channels of the VOR and the TACAN at each VORTAC facility are “paired” in accordance with a national plan to simplify airborne operation. 1−1−7. Distance Measuring Equipment (DME) a. In the operation of DME, paired pulses at a specific spacing are sent out from the aircraft (this is the interrogation) and are received at the ground station. The ground station (transponder) then transmits paired pulses back to the aircraft at the same pulse spacing but on a different frequency. The time required for the round trip of this signal exchange is measured in the airborne DME unit and is translated into distance (nautical miles) from the aircraft to the ground station. b. Operating on the line−of−sight principle, DME furnishes distance information with a very high degree of accuracy. Reliable signals may be received at distances up to 199 NM at line−of−sight altitude with an accuracy of better than 1/2 mile or 3 percent of the distance, whichever is greater. Distance information received from DME equipment is SLANT RANGE distance and not actual horizontal distance. c. Operating frequency range of a DME according to ICAO Annex 10 is from 960 MHz to 1215 MHz. Aircraft equipped with TACAN equipment will receive distance information from a VORTAC Navigation Aids e. Due to the limited number of available frequencies, assignment of paired frequencies is required for certain military noncollocated VOR and TACAN facilities which serve the same area but which may be separated by distances up to a few miles. f. VOR/DME, VORTAC, ILS/DME, and LOC/ DME facilities are identified by synchronized identifications which are transmitted on a time share basis. The VOR or localizer portion of the facility is identified by a coded tone modulated at 1020 Hz or a combination of code and voice. The TACAN or DME is identified by a coded tone modulated at 1350 Hz. The DME or TACAN coded identification is transmitted one time for each three or four times that the VOR or localizer coded identification is transmitted. When either the VOR or the DME is inoperative, it is important to recognize which identifier is retained for the operative facility. A single coded identification with a repetition interval of approximately 30 seconds indicates that the DME is operative. g. Aircraft equipment which provides for automatic DME selection assures reception of azimuth and distance information from a common source when designated VOR/DME, VORTAC and ILS/ DME navigation facilities are selected. Pilots are cautioned to disregard any distance displays from automatically selected DME equipment when VOR or ILS facilities, which do not have the DME feature installed, are being used for position determination. 1−1−8. NAVAID Service Volumes a. The FAA publishes Standard Service Volumes (SSVs) for most NAVAIDs. The SSV is a three−dimensional volume within which the FAA ensures that a signal can be received with adequate 1−1−5 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 signal strength and course quality, and is free from interference from other NAVAIDs on similar frequencies (e.g., co−channel or adjacent−channel interference). However, the SSV signal protection does not include potential blockage from terrain or obstructions. The SSV is principally intended for off−route navigation, such as proceeding direct to or from a VOR when not on a published instrument procedure or route. Navigation on published instrument procedures (e.g., approaches or departures) or routes (e.g., Victor routes) may use NAVAIDs outside of the SSV, when Extended Service Volume (ESV) is approved, since adequate signal strength, course quality, and freedom from interference are verified by the FAA prior to the publishing of the instrument procedure or route. NOTE− A conical area directly above the NAVAID is generally not usable for navigation. b. A NAVAID will have service volume restrictions if it does not conform to signal strength and course quality standards throughout the published SSV. Service volume restrictions are first published in Notices to Air Missions (NOTAMs) and then with the alphabetical listing of the NAVAIDs in the Chart Supplement. Service volume restrictions do not generally apply to published instrument procedures or routes unless published in NOTAMs for the affected instrument procedure or route. c. VOR/DME/TACAN Standard Service Volumes (SSV). 1. The three original SSVs are shown in FIG 1−1−1 and are designated with three classes of NAVAIDs: Terminal (T), Low (L), and High (H). The usable distance of the NAVAID depends on the altitude Above the Transmitter Height (ATH) for each class. The lower edge of the usable distance when below 1,000 feet ATH is shown in FIG 1−1−2 for Terminal NAVAIDs and in FIG 1−1−3 for Low and High NAVAIDs. FIG 1−1−1 Original Standard Service Volumes 1−1−6 Navigation Aids 6/17/21 AIM FIG 1−1−2 Lower Edge of the Terminal Service Volume (in altitude ATH) FIG 1−1−3 Lower Edge of Low and High Service Volumes (in altitude ATH) Navigation Aids 1−1−7 AIM 6/17/21 2. With the progression of navigation capabilities to Performance Based Navigation (PBN), additional capabilities for off−route navigation are necessary. For example, the VOR MON (See paragraph 1−1−3 f.) requires the use of VORs at 5,000 feet AGL, which is beyond the original SSV ranges. Additionally, PBN procedures using DME require extended ranges. As a result, the FAA created four additional SSVs. Two of the new SSVs are associated with VORs: VOR Low (VL) and VOR High (VH), as shown in FIG 1−1−4. The other two new SSVs are associated with DME: DME Low (DL) and DME High (DH), as shown in FIG 1−1−5. The SSV at altitudes below 1,000 feet for the VL and VH are the same as FIG 1−1−3. The SSVs at altitudes below 12,900 feet for the DL and DH SSVs correspond to a conservative estimate of the DME radio line of sight (RLOS) coverage at each altitude (not including possible terrain blockage). FIG 1−1−4 New VOR Service Volumes 1−1−8 Navigation Aids 6/17/21 AIM FIG 1−1−5 New DME Service Volumes NOTE− 1. In the past, NAVAIDs at one location typically all had the same SSV. For example, a VORTAC typically had a High (H) SSV for the VOR, the TACAN azimuth, and the TACAN DME, or a Low (L) or Terminal (T) SSV for all three. A VOR/DME typically had a High (H), Low (L), or Terminal (T) for both the VOR and the DME. A common SSV may no longer be the case at all locations. A VOR/DME, for example, could have an SSV of VL for the VOR and DH for the DME, or other combinations. 2. The TACAN azimuth will only be classified as T, L, or H. Navigation Aids 3. TBL 1−1−1 is a tabular summary of the VOR, DME, and TACAN NAVAID SSVs, not including altitudes below 1,000 feet ATH for VOR and TACAN Azimuth, and not including ranges for altitudes below 12,900 feet for TACAN and DME. 1−1−9 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 TBL 1−1−1 VOR/DME/TACAN Standard Service Volumes SSV Designator T (Terminal) L (Low Altitude) H (High Altitude) VL (VOR Low) VH (VOR High) DL (DME Low) DH (DME High) Altitude and Range Boundaries From 1,000 feet ATH up to and including 12,000 feet ATH at radial distances out to 25 NM. From 1,000 feet ATH up to and including 18,000 feet ATH at radial distances out to 40 NM. From 1,000 feet ATH up to and including 14,500 feet ATH at radial distances out to 40 NM. From 14,500 ATH up to and including 60,000 feet at radial distances out to 100 NM. From 18,000 feet ATH up to and including 45,000 feet ATH at radial distances out to 130 NM. From 1,000 feet ATH up to but not including 5,000 feet ATH at radial distances out to 40 NM. From 5,000 feet ATH up to but not including 18,000 feet ATH at radial distances out to 70 NM. From 1,000 feet ATH up to but not including 5,000 feet ATH at radial distances out to 40 NM. From 5,000 feet ATH up to but not including 14,500 feet ATH at radial distances out to 70 NM. From 14,500 ATH up to and including 60,000 feet at radial distances out to 100 NM. From 18,000 feet ATH up to and including 45,000 feet ATH at radial distances out to 130 NM. For altitudes up to 12,900 feet ATH at a radial distance corresponding to the LOS to the NAVAID. From 12,900 feet ATH up to but not including 18,000 feet ATH at radial distances out to 130 NM For altitudes up to 12,900 feet ATH at a radial distance corresponding to the LOS to the NAVAID. From 12,900 ATH up to and including 60,000 feet at radial distances out to 100 NM. From 12,900 feet ATH up to and including 45,000 feet ATH at radial distances out to 130 NM. d. Nondirectional Radio Beacon (NDB) SSVs. NDBs are classified according to their intended use. The ranges of NDB service volumes are shown in TBL 1−1−2. The distance (radius) is the same at all altitudes for each class. TBL 1−1−2 NDB Service Volumes Class Distance (Radius) (NM) Compass Locator 15 MH 25 H 50* HH 75 *Service ranges of individual facilities may be less than 50 nautical miles (NM). Restrictions to service volumes are first published as a Notice to Air Missions and then with the alphabetical listing of the NAVAID in the Chart Supplement U.S. 1−1−9. Instrument Landing System (ILS) a. General 1. The ILS is designed to provide an approach path for exact alignment and descent of an aircraft on final approach to a runway. 1−1−10 2. The basic components of an ILS are the localizer, glide slope, and Outer Marker (OM) and, when installed for use with Category II or Category III instrument approach procedures, an Inner Marker (IM). Navigation Aids 12/2/21 6/17/21 3. The system may be divided functionally into three parts: slope. DME. (a) Guidance information: localizer, glide (b) Range information: marker beacon, (c) Visual information: approach lights, touchdown and centerline lights, runway lights. 4. The following means may be used to substitute for the OM: (a) Compass locator; or (b) Precision Approach Radar (PAR); or (c) Airport Surveillance Radar (ASR); or (d) Distance Measuring Equipment (DME), Very High Frequency Omni−directional Range (VOR), or Nondirectional beacon fixes authorized in the Standard Instrument Approach Procedure; or (e) Very High Frequency Omni−directional Radio Range (VOR); or (f) Nondirectional beacon fixes authorized in the Standard Instrument Approach Procedure; or (g) A suitable RNAV system with Global Positioning System (GPS), capable of fix identification on a Standard Instrument Approach Procedure. 5. Where a complete ILS system is installed on each end of a runway; (i.e., the approach end of Runway 4 and the approach end of Runway 22) the ILS systems are not in service simultaneously. AIM 3. The course line along the extended centerline of a runway, in the opposite direction to the front course is called the back course. CAUTION− Unless the aircraft’s ILS equipment includes reverse sensing capability, when flying inbound on the back course it is necessary to steer the aircraft in the direction opposite the needle deflection when making corrections from off−course to on−course. This “flying away from the needle” is also required when flying outbound on the front course of the localizer. Do not use back course signals for approach unless a back course approach procedure is published for that particular runway and the approach is authorized by ATC. 4. Identification is in International Morse Code and consists of a three−letter identifier preceded by the letter I ( ) transmitted on the localizer frequency. EXAMPLE− I−DIA 5. The localizer provides course guidance throughout the descent path to the runway threshold from a distance of 18 NM from the antenna between an altitude of 1,000 feet above the highest terrain along the course line and 4,500 feet above the elevation of the antenna site. Proper off−course indications are provided throughout the following angular areas of the operational service volume: (a) To 10 degrees either side of the course along a radius of 18 NM from the antenna; and (b) From 10 to 35 degrees either side of the course along a radius of 10 NM. (See FIG 1−1−6.) FIG 1−1−6 Limits of Localizer Coverage b. Localizer ° 35 1. The localizer transmitter operates on one of 40 ILS channels within the frequency range of 108.10 to 111.95 MHz. Signals provide the pilot with course guidance to the runway centerline. Navigation Aids RUNWAY LOCALIZER ANTENNA 118 8 NM 110 0 NM 2. The approach course of the localizer is called the front course and is used with other functional parts, e.g., glide slope, marker beacons, etc. The localizer signal is transmitted at the far end of the runway. It is adjusted for a course width of (full scale fly−left to a full scale fly−right) of 700 feet at the runway threshold. 10° 10° 35 ° NORMAL LIMITS OF LOCALIZER COVERAGE: THE SAME AREA APPLIES TO A BACK COURSE WHEN PROVIDED. 1−1−11 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 6. Unreliable signals may be received outside of these areas. ATC may clear aircraft on procedures beyond the service volume when the controller initiates the action or when the pilot requests, and radar monitoring is provided. 7. The areas described in paragraph 1−1−9 b5 and depicted in FIG 1−1−6 represent a Standard Service Volume (SSV) localizer. All charted procedures with localizer coverage beyond the 18 NM SSV have been through the approval process for Expanded Service Volume (ESV), and have been validated by flight inspection. (See FIG 1−1−7.) FIG 1−1−7 ILS Expanded Service Volume c. Localizer Type Directional Aid (LDA) 1. The LDA is of comparable use and accuracy to a localizer but is not part of a complete ILS. The LDA course usually provides a more precise approach course than the similar Simplified Directional Facility (SDF) installation, which may have a course width of 6 or 12 degrees. 2. The LDA is not aligned with the runway. Straight−in minimums may be published where alignment does not exceed 30 degrees between the course and runway. Circling minimums only are published where this alignment exceeds 30 degrees. 1−1−12 3. A very limited number of LDA approaches also incorporate a glideslope. These are annotated in the plan view of the instrument approach chart with a note, “LDA/Glideslope.” These procedures fall under a newly defined category of approaches called Approach with Vertical Guidance (APV) described in paragraph 5−4−5, Instrument Approach Procedure Charts, subparagraph a7(b), Approach with Vertical Guidance (APV). LDA minima for with and without glideslope is provided and annotated on the minima lines of the approach chart as S−LDA/GS and S−LDA. Because the final approach course is not aligned with the runway centerline, additional Navigation Aids 12/2/21 6/17/21 maneuvering will be required compared to an ILS approach. d. Glide Slope/Glide Path 1. The UHF glide slope transmitter, operating on one of the 40 ILS channels within the frequency range 329.15 MHz, to 335.00 MHz radiates its signals in the direction of the localizer front course. The term “glide path” means that portion of the glide slope that intersects the localizer. CAUTION− False glide slope signals may exist in the area of the localizer back course approach which can cause the glide slope flag alarm to disappear and present unreliable glide slope information. Disregard all glide slope signal indications when making a localizer back course approach unless a glide slope is specified on the approach and landing chart. 2. The glide slope transmitter is located between 750 feet and 1,250 feet from the approach end of the runway (down the runway) and offset 250 to 650 feet from the runway centerline. It transmits a glide path beam 1.4 degrees wide (vertically). The signal provides descent information for navigation down to the lowest authorized decision height (DH) specified in the approved ILS approach procedure. The glidepath may not be suitable for navigation below the lowest authorized DH and any reference to glidepath indications below that height must be supplemented by visual reference to the runway environment. Glidepaths with no published DH are usable to runway threshold. 3. The glide path projection angle is normally adjusted to 3 degrees above horizontal so that it intersects the MM at about 200 feet and the OM at about 1,400 feet above the runway elevation. The glide slope is normally usable to the distance of 10 NM. However, at some locations, the glide slope has been certified for an extended service volume which exceeds 10 NM. 4. Pilots must be alert when approaching the glidepath interception. False courses and reverse sensing will occur at angles considerably greater than the published path. 5. Make every effort to remain on the indicated glide path. CAUTION− Avoid flying below the glide path to assure obstacle/terrain clearance is maintained. Navigation Aids AIM 6. The published glide slope threshold crossing height (TCH) DOES NOT represent the height of the actual glide path on−course indication above the runway threshold. It is used as a reference for planning purposes which represents the height above the runway threshold that an aircraft’s glide slope antenna should be, if that aircraft remains on a trajectory formed by the four−mile−to−middle marker glidepath segment. 7. Pilots must be aware of the vertical height between the aircraft’s glide slope antenna and the main gear in the landing configuration and, at the DH, plan to adjust the descent angle accordingly if the published TCH indicates the wheel crossing height over the runway threshold may not be satisfactory. Tests indicate a comfortable wheel crossing height is approximately 20 to 30 feet, depending on the type of aircraft. NOTE− The TCH for a runway is established based on several factors including the largest aircraft category that normally uses the runway, how airport layout affects the glide slope antenna placement, and terrain. A higher than optimum TCH, with the same glide path angle, may cause the aircraft to touch down further from the threshold if the trajectory of the approach is maintained until the flare. Pilots should consider the effect of a high TCH on the runway available for stopping the aircraft. e. Distance Measuring Equipment (DME) 1. When installed with the ILS and specified in the approach procedure, DME may be used: (a) In lieu of the OM; (b) As a back course (BC) final approach fix (FAF); and (c) To establish other fixes on the localizer course. 2. In some cases, DME from a separate facility may be used within Terminal Instrument Procedures (TERPS) limitations: ments; (a) To provide ARC initial approach seg(b) As a FAF for BC approaches; and (c) As a substitute for the OM. f. Marker Beacon 1. ILS marker beacons have a rated power output of 3 watts or less and an antenna array designed to produce an elliptical pattern with 1−1−13 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 dimensions, at 1,000 feet above the antenna, of approximately 2,400 feet in width and 4,200 feet in length. Airborne marker beacon receivers with a selective sensitivity feature should always be operated in the “low” sensitivity position for proper reception of ILS marker beacons. 2. ILS systems may have an associated OM. An MM is no longer required. Locations with a Category II ILS also have an Inner Marker (IM). Due to advances in both ground navigation equipment and airborne avionics, as well as the numerous means that may be used as a substitute for a marker beacon, the current requirements for the use of marker beacons are: (a) An OM or suitable substitute identifies the Final Approach Fix (FAF) for nonprecision approach (NPA) operations (for example, localizer only); and (b) The MM indicates a position approximately 3,500 feet from the landing threshold. This is also the position where an aircraft on the glide path will be at an altitude of approximately 200 feet above the elevation of the touchdown zone. A MM is no longer operationally required. There are some MMs still in use, but there are no MMs being installed at new ILS sites by the FAA; and (c) An IM, where installed, indicates the point at which an aircraft is at decision height on the glide path during a Category II ILS approach. An IM is only required for CAT II operations that do not have a published radio altitude (RA) minimum. TBL 1−1−3 Marker Passage Indications Marker Code Light OM MM IM BC BLUE AMBER WHITE WHITE 3. A back course marker normally indicates the ILS back course final approach fix where approach descent is commenced. g. Compass Locator 1. Compass locator transmitters are often situated at the MM and OM sites. The transmitters have a power of less than 25 watts, a range of at least 15 miles and operate between 190 and 535 kHz. At 1−1−14 some locations, higher powered radio beacons, up to 400 watts, are used as OM compass locators. 2. Compass locators transmit two letter identification groups. The outer locator transmits the first two letters of the localizer identification group, and the middle locator transmits the last two letters of the localizer identification group. h. ILS Frequency (See TBL 1−1−4.) TBL 1−1−4 Frequency Pairs Allocated for ILS Localizer MHz Glide Slope 108.10 108.15 108.3 108.35 108.5 108.55 108.7 Localizer MHz 108.75 108.9 108.95 109.1 109.15 109.3 109.35 109.50 109.55 109.70 109.75 109.90 109.95 110.1 110.15 110.3 110.35 110.5 110.55 110.70 110.75 110.90 110.95 111.10 111.15 111.30 111.35 111.50 111.55 111.70 334.70 334.55 334.10 333.95 329.90 329.75 330.50 Glide Slope 330.35 329.30 329.15 331.40 331.25 332.00 331.85 332.60 332.45 333.20 333.05 333.80 333.65 334.40 334.25 335.00 334.85 329.60 329.45 330.20 330.05 330.80 330.65 331.70 331.55 332.30 332.15 332.9 332.75 333.5 Navigation Aids 12/2/21 6/17/21 AIM 111.75 111.90 111.95 333.35 331.1 330.95 i. ILS Minimums 1. The lowest authorized ILS minimums, with all required ground and airborne systems components operative, are: (a) Category I. Decision Height (DH) 200 feet and Runway Visual Range (RVR) 2,400 feet (with touchdown zone and centerline lighting, RVR 1,800 feet), or (with Autopilot or FD or HUD, RVR 1,800 feet); (b) Special Authorization Category I. DH 150 feet and Runway Visual Range (RVR) 1,400 feet, HUD to DH; (c) Category II. DH 100 feet and RVR 1,200 feet (with autoland or HUD to touchdown and noted on authorization, RVR 1,000 feet); (d) Special Authorization Category II with Reduced Lighting. DH 100 feet and RVR 1,200 feet with autoland or HUD to touchdown and noted on authorization (touchdown zone, centerline lighting, and ALSF−2 are not required); (e) Category IIIa. No DH or DH below 100 feet and RVR not less than 700 feet; (f) Category IIIb. No DH or DH below 50 feet and RVR less than 700 feet but not less than 150 feet; and (g) Category IIIc. No DH and no RVR limitation. NOTE− Special authorization and equipment required for Categories II and III. j. Inoperative ILS Components 1. Inoperative localizer. When the localizer fails, an ILS approach is not authorized. 2. Inoperative glide slope. When the glide slope fails, the ILS reverts to a non−precision localizer approach. REFERENCE− See the inoperative component table in the U.S. Government Terminal Procedures Publication (TPP), for adjustments to minimums due to inoperative airborne or ground system equipment. k. ILS Course Distortion Navigation Aids 1. All pilots should be aware that disturbances to ILS localizer and glide slope courses may occur when surface vehicles or aircraft are operated near the localizer or glide slope antennas. Most ILS installations are subject to signal interference by either surface vehicles, aircraft or both. ILS CRITICAL AREAS are established near each localizer and glide slope antenna. 2. ATC issues control instructions to avoid interfering operations within ILS critical areas at controlled airports during the hours the Airport Traffic Control Tower (ATCT) is in operation as follows: (a) Weather Conditions. Official weather observation is a ceiling of less than 800 feet and/or visibility 2 miles. (1) Localizer Critical Area. Except for aircraft that land, exit a runway, depart, or execute a missed approach, vehicles and aircraft are not authorized in or over the critical area when an arriving aircraft is inside the outer marker (OM) or the fix used in lieu of the OM. Additionally, whenever the official weather observation is a ceiling of less than 200 feet or RVR less than 2,000 feet, do not authorize vehicles or aircraft operations in or over the area when an arriving aircraft is inside the MM, or in the absence of a MM, ½ mile final. (2) Glide Slope Critical Area. Do not authorize vehicles or aircraft operations in or over the area when an arriving aircraft is inside the ILS outer marker (OM), or the fix used in lieu of the OM, unless the arriving aircraft has reported the runway in sight and is circling or side−stepping to land on another runway. (b) Weather Conditions. At or above ceiling 800 feet and/or visibility 2 miles. (1) No critical area protective action is provided under these conditions. (2) A flight crew, under these conditions, should advise the tower that it will conduct an AUTOLAND or COUPLED approach. EXAMPLE− Denver Tower, United 1153, Request Autoland/Coupled Approach (runway) ATC replies with: United 1153, Denver Tower, Roger, Critical Areas not protected. 3. Aircraft holding below 5,000 feet between the outer marker and the airport may cause localizer 1−1−15 7110.65R CHG 2 AIM AIM signal variations for aircraft conducting the ILS approach. Accordingly, such holding is not authorized when weather or visibility conditions are less than ceiling 800 feet and/or visibility 2 miles. 4. Pilots are cautioned that vehicular traffic not subject to ATC may cause momentary deviation to ILS course or glide slope signals. Also, critical areas are not protected at uncontrolled airports or at airports with an operating control tower when weather or visibility conditions are above those requiring protective measures. Aircraft conducting coupled or autoland operations should be especially alert in monitoring automatic flight control systems. (See FIG 1−1−8.) NOTE− Unless otherwise coordinated through Flight Standards, ILS signals to Category I runways are not flight inspected below the point that is 100 feet less than the decision altitude (DA). Guidance signal anomalies may be encountered below this altitude. 1−1−10. Simplified Directional Facility (SDF) a. The SDF provides a final approach course similar to that of the ILS localizer. It does not provide glide slope information. A clear understanding of the ILS localizer and the additional factors listed below completely describe the operational characteristics and use of the SDF. 1−1−16 3/15/07 12/2/21 6/17/21 b. The SDF transmits signals within the range of 108.10 to 111.95 MHz. c. The approach techniques and procedures used in an SDF instrument approach are essentially the same as those employed in executing a standard localizer approach except the SDF course may not be aligned with the runway and the course may be wider, resulting in less precision. d. Usable off−course indications are limited to 35 degrees either side of the course centerline. Instrument indications received beyond 35 degrees should be disregarded. e. The SDF antenna may be offset from the runway centerline. Because of this, the angle of convergence between the final approach course and the runway bearing should be determined by reference to the instrument approach procedure chart. This angle is generally not more than 3 degrees. However, it should be noted that inasmuch as the approach course originates at the antenna site, an approach which is continued beyond the runway threshold will lead the aircraft to the SDF offset position rather than along the runway centerline. f. The SDF signal is fixed at either 6 degrees or 12 degrees as necessary to provide maximum flyability and optimum course quality. g. Identification consists of a three−letter identifier transmitted in Morse Code on the SDF frequency. The appropriate instrument approach chart will indicate the identifier used at a particular airport. Navigation Aids 6/17/21 AIM FIG 1−1−8 FAA Instrument Landing Systems Navigation Aids 1−1−17 7110.65R CHG 2 AIM AIM 1−1−11. NAVAID Identifier Removal During Maintenance During periods of routine or emergency maintenance, coded identification (or code and voice, where applicable) is removed from certain FAA NAVAIDs. Removal of identification serves as a warning to pilots that the facility is officially off the air for tune−up or repair and may be unreliable even though intermittent or constant signals are received. NOTE− During periods of maintenance VHF ranges may radiate a T−E−S−T code (- -). NOTE− DO NOT attempt to fly a procedure that is NOTAMed out of service even if the identification is present. In certain cases, the identification may be transmitted for short periods as part of the testing. 1−1−12. NAVAIDs with Voice a. Voice equipped en route radio navigational aids are under the operational control of either a Flight Service Station (FSS) or an approach control facility. Facilities with two−way voice communication available are indicated in the Chart Supplement U.S. and aeronautical charts. b. Unless otherwise noted on the chart, all radio navigation aids operate continuously except during shutdowns for maintenance. Hours of operation of facilities not operating continuously are annotated on charts and in the Chart Supplement U.S. 1−1−13. User Reports Requested on NAVAID Outages a. Users of the National Airspace System (NAS) can render valuable assistance in the early correction of NAVAID malfunctions or GNSS problems and are encouraged to report their observations of undesirable avionics performance. Although NAVAIDs are monitored by electronic detectors, adverse effects of electronic interference, new obstructions, or changes in terrain near the NAVAID can exist without detection by the ground monitors. Some of the characteristics of malfunction or deteriorating performance which should be reported are: erratic course or bearing indications; intermittent, or full, flag alarm; garbled, missing or obviously improper coded identification; poor quality communications 1−1−18 3/15/07 5/19/22 6/17/21 reception; or, in the case of frequency interference, an audible hum or tone accompanying radio communications or NAVAID identification. GNSS problems are often characterized by navigation degradation or service loss indications. For instance, pilots conducting operations in areas where there is GNSS interference may be unable to use GPS for navigation, and ADS−B may be unavailable for surveillance. Radio frequency interference may affect both navigation for the pilot and surveillance by the air traffic controller. Depending on the equipment and integration, either an advisory light or message may alert the pilot. Air traffic controllers monitoring ADS−B reports may stop receiving ADS−B position messages and associated aircraft tracks. b. Malfunctioning, faulty, inappropriately installed, operated, or modified GPS re−radiator systems, intended to be used for aircraft maintenance activities, have resulted in unintentional disruption of aviation GPS receivers. This type of disruption could result in unflagged, erroneous position−information output to primary flight displays/indicators and to other aircraft and air traffic control systems. Since Receiver Autonomous Integrity Monitoring (RAIM) is only partially effective against this type of disruption (effectively a “signal spoofing”), the pilot may not be aware of any erroneous navigation indications; ATC may be the only means available to identify these disruptions and detect unexpected aircraft positions while monitoring aircraft for IFR separation. c. Pilots encountering navigation error events should transition to another source of navigation and request amended clearances from ATC as necessary. d. Pilots are encouraged to submit detailed reports of NAVAID or GPS anomaly as soon as practical. Pilot reports of navigation error events should contain the following information: 1. Date and time the anomaly was observed, and NAVAID ID (or GPS). 2. Location of the aircraft at the time the anomaly started and ended (e.g., latitude/longitude or bearing/distance from a reference point), 3. Heading, altitude, type of aircraft (make/ model/call sign), 4. Type of avionics/receivers in use (e.g., make/model/software series or version), Navigation Aids 5/19/22 6/17/21 5. Number of satellites being tracked, if applicable, 6. Description of the position/navigation/timing anomaly observed, and duration of the event, 7. Consequences/operational impact(s) of the NAVAID or GPS anomaly, 8. Actions taken to mitigate the anomaly and/or remedy provided by the ATC facility, 9. Post flight pilot/maintenance actions taken. e. Pilots operating an aircraft in controlled airspace under IFR shall comply with CFR § 91.187 and promptly report as soon as practical to ATC any malfunctions of navigational equipment occurring in flight; pilots should submit initial reports: 1. Immediately, by radio to the controlling ATC facility or FSS. 2. By telephone to the nearest ATC facility controlling the airspace where the disruption was experienced. 3. Additionally, GPS problems should be reported, post flight, by Internet via the GPS Anomaly Reporting Form at http://www.faa.gov/air_traffic/nas/gps_reports/. f. To minimize ATC workload, GPS anomalies associated with known testing NOTAMs should NOT be reported in−flight to ATC in detail; EXCEPT when: 1. GPS degradation is experienced outside the NOTAMed area, 2. Pilot observes any unexpected consequences (e.g., equipment failure, suspected spoofing, failure of unexpected aircraft systems, such as TAWS). 1−1−14. LORAN NOTE− In accordance with the 2010 DHS Appropriations Act, the U.S. Coast Guard (USCG) terminated the transmission of all U.S. LORAN−C signals on 08 Feb 2010. The USCG also terminated the transmission of the Russian American signals on 01 Aug 2010, and the Canadian LORAN−C signals on 03 Aug 2010. For more information, visit http://www.navcen.uscg.gov. Operators should also note that TSO−C60b, AIRBORNE AREA NAVIGATION EQUIPMENT USING LORAN−C INPUTS, has been canceled by the FAA. Navigation Aids AIM 1−1−15. Inertial Reference Unit (IRU), Inertial Navigation System (INS), and Attitude Heading Reference System (AHRS) a. IRUs are self−contained systems comprised of gyros and accelerometers that provide aircraft attitude (pitch, roll, and heading), position, and velocity information in response to signals resulting from inertial effects on system components. Once aligned with a known position, IRUs continuously calculate position and velocity. IRU position accuracy decays with time. This degradation is known as “drift.” b. INSs combine the components of an IRU with an internal navigation computer. By programming a series of waypoints, these systems will navigate along a predetermined track. c. AHRSs are electronic devices that provide attitude information to aircraft systems such as weather radar and autopilot, but do not directly compute position information. d. Aircraft equipped with slaved compass systems may be susceptible to heading errors caused by exposure to magnetic field disturbances (flux fields) found in materials that are commonly located on the surface or buried under taxiways and ramps. These materials generate a magnetic flux field that can be sensed by the aircraft’s compass system flux detector or “gate,” which can cause the aircraft’s system to align with the material’s magnetic field rather than the earth’s natural magnetic field. The system’s erroneous heading may not self-correct. Prior to take off pilots should be aware that a heading misalignment may have occurred during taxi. Pilots are encouraged to follow the manufacturer’s or other appropriate procedures to correct possible heading misalignment before take off is commenced. 1−1−16. Doppler Radar Doppler Radar is a semiautomatic self−contained dead reckoning navigation system (radar sensor plus computer) which is not continuously dependent on information derived from ground based or external aids. The system employs radar signals to detect and measure ground speed and drift angle, using the aircraft compass system as its directional reference. Doppler is less accurate than INS, however, and the use of an external reference is required for periodic updates if acceptable position accuracy is to be achieved on long range flights. 1−1−19 7110.65R CHG 2 AIM AIM 1−1−17. Global Positioning System (GPS) a. System Overview 1. System Description. The Global Positioning System is a space-based radio navigation system used to determine precise position anywhere in the world. The 24 satellite constellation is designed to ensure at least five satellites are always visible to a user worldwide. A minimum of four satellites is necessary for receivers to establish an accurate three−dimensional position. The receiver uses data from satellites above the mask angle (the lowest angle above the horizon at which a receiver can use a satellite). The Department of Defense (DOD) is responsible for operating the GPS satellite constellation and monitors the GPS satellites to ensure proper operation. Each satellite’s orbital parameters (ephemeris data) are sent to each satellite for broadcast as part of the data message embedded in the GPS signal. The GPS coordinate system is the Cartesian earth−centered, earth−fixed coordinates as specified in the World Geodetic System 1984 (WGS−84). 2. System Availability and Reliability. (a) The status of GPS satellites is broadcast as part of the data message transmitted by the GPS satellites. GPS status information is also available by means of the U.S. Coast Guard navigation information service: (703) 313−5907, Internet: http://www.navcen.uscg.gov/. Additionally, satellite status is available through the Notice to Air Missions (NOTAM) system. (b) GNSS operational status depends on the type of equipment being used. For GPS−only equipment TSO−C129 or TSO-C196(), the operational status of non−precision approach capability for flight planning purposes is provided through a prediction program that is embedded in the receiver or provided separately. 3. Receiver Autonomous Integrity Monitoring (RAIM). RAIM is the capability of a GPS receiver to perform integrity monitoring on itself by ensuring available satellite signals meet the integrity requirements for a given phase of flight. Without RAIM, the pilot has no assurance of the GPS position integrity. RAIM provides immediate feedback to the pilot. This fault detection is critical for performance-based navigation (PBN)(see Paragraph 1−2−1, Performance−Based Navigation (PBN) and Area Navigation (RNAV), for an introduction to PBN), because delays 1−1−20 3/15/07 5/19/22 6/17/21 of up to two hours can occur before an erroneous satellite transmission is detected and corrected by the satellite control segment. (a) In order for RAIM to determine if a satellite is providing corrupted information, at least one satellite, in addition to those required for navigation, must be in view for the receiver to perform the RAIM function. RAIM requires a minimum of 5 satellites, or 4 satellites and barometric altimeter input (baro−aiding), to detect an integrity anomaly. Baro−aiding is a method of augmenting the GPS integrity solution by using a non-satellite input source in lieu of the fifth satellite. Some GPS receivers also have a RAIM capability, called fault detection and exclusion (FDE), that excludes a failed satellite from the position solution; GPS receivers capable of FDE require 6 satellites or 5 satellites with baro−aiding. This allows the GPS receiver to isolate the corrupt satellite signal, remove it from the position solution, and still provide an integrity-assured position. To ensure that baro−aiding is available, enter the current altimeter setting into the receiver as described in the operating manual. Do not use the GPS derived altitude due to the large GPS vertical errors that will make the integrity monitoring function invalid. (b) There are generally two types of RAIM fault messages. The first type of message indicates that there are not enough satellites available to provide RAIM integrity monitoring. The GPS navigation solution may be acceptable, but the integrity of the solution cannot be determined. The second type indicates that the RAIM integrity monitor has detected a potential error and that there is an inconsistency in the navigation solution for the given phase of flight. Without RAIM capability, the pilot has no assurance of the accuracy of the GPS position. 4. Selective Availability. Selective Availability (SA) is a method by which the accuracy of GPS is intentionally degraded. This feature was designed to deny hostile use of precise GPS positioning data. SA was discontinued on May 1, 2000, but many GPS receivers are designed to assume that SA is still active. New receivers may take advantage of the discontinuance of SA based on the performance values in ICAO Annex 10. b. Operational Use of GPS. U.S. civil operators may use approved GPS equipment in oceanic airspace, certain remote areas, the National Airspace Navigation Aids 5/19/22 6/17/21 System and other States as authorized (please consult the applicable Aeronautical Information Publication). Equipage other than GPS may be required for the desired operation. GPS navigation is used for both Visual Flight Rules (VFR) and Instrument Flight Rules (IFR) operations. 1. VFR Operations (a) GPS navigation has become an asset to VFR pilots by providing increased navigational capabilities and enhanced situational awareness. Although GPS has provided many benefits to the VFR pilot, care must be exercised to ensure that system capabilities are not exceeded. VFR pilots should integrate GPS navigation with electronic navigation (when possible), as well as pilotage and dead reckoning. (b) GPS receivers used for VFR navigation vary from fully integrated IFR/VFR installation used to support VFR operations to hand−held devices. Pilots must understand the limitations of the receivers prior to using in flight to avoid misusing navigation information. (See TBL 1−1−6.) Most receivers are not intuitive. The pilot must learn the various keystrokes, knob functions, and displays that are used in the operation of the receiver. Some manufacturers provide computer−based tutorials or simulations of their receivers that pilots can use to become familiar with operating the equipment. (c) When using GPS for VFR operations, RAIM capability, database currency, and antenna location are critical areas of concern. (1) RAIM Capability. VFR GPS panel mount receivers and hand−held units have no RAIM alerting capability. This prevents the pilot from being alerted to the loss of the required number of satellites in view, or the detection of a position error. Pilots should use a systematic cross−check with other navigation techniques to verify position. Be suspicious of the GPS position if a disagreement exists between the two positions. (2) Database Currency. Check the currency of the database. Databases must be updated for IFR operations and should be updated for all other operations. However, there is no requirement for databases to be updated for VFR navigation. It is not recommended to use a moving map with an outdated database in and around critical airspace. Pilots using an outdated database should verify waypoints using Navigation Aids AIM current aeronautical products; for example, Chart Supplement U.S., Sectional Chart, or En Route Chart. (3) Antenna Location. The antenna location for GPS receivers used for IFR and VFR operations may differ. VFR antennae are typically placed for convenience more than performance, while IFR installations ensure a clear view is provided with the satellites. Antennae not providing a clear view have a greater opportunity to lose the satellite navigational signal. This is especially true in the case of hand−held GPS receivers. Typically, suction cups are used to place the GPS antennas on the inside of cockpit windows. While this method has great utility, the antenna location is limited to the cockpit or cabin which rarely provides a clear view of all available satellites. Consequently, signal losses may occur due to aircraft structure blocking satellite signals, causing a loss of navigation capability. These losses, coupled with a lack of RAIM capability, could present erroneous position and navigation information with no warning to the pilot. While the use of a hand−held GPS for VFR operations is not limited by regulation, modification of the aircraft, such as installing a panel− or yoke−mounted holder, is governed by 14 CFR Part 43. Consult with your mechanic to ensure compliance with the regulation and safe installation. (d) Do not solely rely on GPS for VFR navigation. No design standard of accuracy or integrity is used for a VFR GPS receiver. VFR GPS receivers should be used in conjunction with other forms of navigation during VFR operations to ensure a correct route of flight is maintained. Minimize head−down time in the aircraft by being familiar with your GPS receiver’s operation and by keeping eyes outside scanning for traffic, terrain, and obstacles. (e) VFR Waypoints (1) VFR waypoints provide VFR pilots with a supplementary tool to assist with position awareness while navigating visually in aircraft equipped with area navigation receivers. VFR waypoints should be used as a tool to supplement current navigation procedures. The uses of VFR waypoints include providing navigational aids for pilots unfamiliar with an area, waypoint definition of existing reporting points, enhanced navigation in and around Class B and Class C airspace, and enhanced navigation around Special Use Airspace. VFR pilots should rely on appropriate and current aeronautical 1−1−21 7110.65R CHG 2 AIM AIM charts published specifically for visual navigation. If operating in a terminal area, pilots should take advantage of the Terminal Area Chart available for that area, if published. The use of VFR waypoints does not relieve the pilot of any responsibility to comply with the operational requirements of 14 CFR Part 91. (2) VFR waypoint names (for computer− entry and flight plans) consist of five letters beginning with the letters “VP” and are retrievable from navigation databases. The VFR waypoint names are not intended to be pronounceable, and they are not for use in ATC communications. On VFR charts, stand−alone VFR waypoints will be portrayed using the same four−point star symbol used for IFR waypoints. VFR waypoints collocated with visual check points on the chart will be identified by small magenta flag symbols. VFR waypoints collocated with visual check points will be pronounceable based on the name of the visual check point and may be used for ATC communications. Each VFR waypoint name will appear in parentheses adjacent to the geographic location on the chart. Latitude/longitude data for all established VFR waypoints may be found in the appropriate regional Chart Supplement U.S. (3) VFR waypoints may not be used on IFR flight plans. VFR waypoints are not recognized by the IFR system and will be rejected for IFR routing purposes. (4) Pilots may use the five−letter identifier as a waypoint in the route of flight section on a VFR flight plan. Pilots may use the VFR waypoints only when operating under VFR conditions. The point may represent an intended course change or describe the planned route of flight. This VFR filing would be similar to how a VOR would be used in a route of flight. (5) VFR waypoints intended for use during flight should be loaded into the receiver while on the ground. Once airborne, pilots should avoid programming routes or VFR waypoint chains into their receivers. (6) Pilots should be vigilant to see and avoid other traffic when near VFR waypoints. With the increased use of GPS navigation and accuracy, expect increased traffic near VFR waypoints. Regardless of the class of airspace, monitor the available ATC frequency for traffic information on 1−1−22 3/15/07 5/19/22 6/17/21 other aircraft operating in the vicinity. See paragraph 7−6−3, VFR in Congested Areas, for more information. 2. IFR Use of GPS (a) General Requirements. Authorization to conduct any GPS operation under IFR requires: (1) GPS navigation equipment used for IFR operations must be approved in accordance with the requirements specified in Technical Standard Order (TSO) TSO−C129(), TSO−C196(), TSO−C145(), or TSO−C146(), and the installation must be done in accordance with Advisory Circular AC 20−138, Airworthiness Approval of Positioning and Navigation Systems. Equipment approved in accordance with TSO−C115a does not meet the requirements of TSO−C129. Visual flight rules (VFR) and hand−held GPS systems are not authorized for IFR navigation, instrument approaches, or as a principal instrument flight reference. (2) Aircraft using un-augmented GPS (TSO-C129() or TSO-C196()) for navigation under IFR must be equipped with an alternate approved and operational means of navigation suitable for navigating the proposed route of flight. (Examples of alternate navigation equipment include VOR or DME/DME/IRU capability). Active monitoring of alternative navigation equipment is not required when RAIM is available for integrity monitoring. Active monitoring of an alternate means of navigation is required when the GPS RAIM capability is lost. (3) Procedures must be established for use in the event that the loss of RAIM capability is predicted to occur. In situations where RAIM is predicted to be unavailable, the flight must rely on other approved navigation equipment, re-route to where RAIM is available, delay departure, or cancel the flight. (4) The GPS operation must be conducted in accordance with the FAA−approved aircraft flight manual (AFM) or flight manual supplement. Flight crew members must be thoroughly familiar with the particular GPS equipment installed in the aircraft, the receiver operation manual, and the AFM or flight manual supplement. Operation, receiver presentation and capabilities of GPS equipment vary. Due to these differences, operation of GPS receivers of different brands, or even models of the same brand, under IFR should not be attempted without thorough Navigation Aids 5/19/22 6/17/21 operational knowledge. Most receivers have a built−in simulator mode, which allows the pilot to become familiar with operation prior to attempting operation in the aircraft. (5) Aircraft navigating by IFR−approved GPS are considered to be performance−based navigation (PBN) aircraft and have special equipment suffixes. File the appropriate equipment suffix in accordance with Appendix 4, TBL 4−2, on the ATC flight plan. If GPS avionics become inoperative, the pilot should advise ATC and amend the equipment suffix. (6) Prior to any GPS IFR operation, the pilot must review appropriate NOTAMs and aeronautical information. (See GPS NOTAMs/Aeronautical Information). (b) Database Requirements. The onboard navigation data must be current and appropriate for the region of intended operation and should include the navigation aids, waypoints, and relevant coded terminal airspace procedures for the departure, arrival, and alternate airfields. (1) Further database guidance for terminal and en route requirements may be found in AC 90-100, U.S. Terminal and En Route Area Navigation (RNAV) Operations. (2) Further database guidance on Required Navigation Performance (RNP) instrument approach operations, RNP terminal, and RNP en route requirements may be found in AC 90-105, Approval Guidance for RNP Operations and Barometric Vertical Navigation in the U.S. National Airspace System. (3) All approach procedures to be flown must be retrievable from the current airborne navigation database supplied by the equipment manufacturer or other FAA−approved source. The system must be able to retrieve the procedure by name from the aircraft navigation database, not just as a manually entered series of waypoints. Manual entry of waypoints using latitude/longitude or place/bearing is not permitted for approach procedures. (4) Prior to using a procedure or waypoint retrieved from the airborne navigation database, the pilot should verify the validity of the database. This verification should include the following preflight and inflight steps: Navigation Aids AIM [a] Preflight: [1] Determine the date of database issuance, and verify that the date/time of proposed use is before the expiration date/time. [2] Verify that the database provider has not published a notice limiting the use of the specific waypoint or procedure. [b] Inflight: [1] Determine that the waypoints and transition names coincide with names found on the procedure chart. Do not use waypoints which do not exactly match the spelling shown on published procedure charts. [2] Determine that the waypoints are logical in location, in the correct order, and their orientation to each other is as found on the procedure chart, both laterally and vertically. NOTE− There is no specific requirement to check each waypoint latitude and longitude, type of waypoint and/or altitude constraint, only the general relationship of waypoints in the procedure, or the logic of an individual waypoint’s location. [3] If the cursory check of procedure logic or individual waypoint location, specified in [b] above, indicates a potential error, do not use the retrieved procedure or waypoint until a verification of latitude and longitude, waypoint type, and altitude constraints indicate full conformity with the published data. (5) Air carrier and commercial operators must meet the appropriate provisions of their approved operations specifications. [a] During domestic operations for commerce or for hire, operators must have a second navigation system capable of reversion or contingency operations. [b] Operators must have two independent navigation systems appropriate to the route to be flown, or one system that is suitable and a second, independent backup capability that allows the operator to proceed safely and land at a different airport, and the aircraft must have sufficient fuel (reference 14 CFR 121.349, 125.203, 129.17, and 135.165). These rules ensure the safety of the operation by preventing a single point of failure. NOTE− An aircraft approved for multi-sensor navigation and 1−1−23 7110.65R CHG 2 AIM AIM equipped with a single navigation system must maintain an ability to navigate or proceed safely in the event that any one component of the navigation system fails, including the flight management system (FMS). Retaining a FMS-independent VOR capability would satisfy this requirement. [c] The requirements for a second system apply to the entire set of equipment needed to achieve the navigation capability, not just the individual components of the system such as the radio navigation receiver. For example, to use two RNAV systems (e.g., GPS and DME/DME/IRU) to comply with the requirements, the aircraft must be equipped with two independent radio navigation receivers and two independent navigation computers (e.g., flight management systems (FMS)). Alternatively, to comply with the requirements using a single RNAV system with an installed and operable VOR capability, the VOR capability must be independent of the FMS. [d] To satisfy the requirement for two independent navigation systems, if the primary navigation system is GPS−based, the second system must be independent of GPS (for example, VOR or DME/DME/IRU). This allows continued navigation in case of failure of the GPS or WAAS services. Recognizing that GPS interference and test events resulting in the loss of GPS services have become more common, the FAA requires operators conducting IFR operations under 14 CFR 121.349, 125.203, 129.17 and 135.65 to retain a non-GPS navigation capability consisting of either DME/DME, IRU, or VOR for en route and terminal operations, and VOR and ILS for final approach. Since this system is to be used as a reversionary capability, single equipage is sufficient. 3. Oceanic, Domestic, En Route, and Terminal Area Operations (a) Conduct GPS IFR operations in oceanic areas only when approved avionics systems are installed. TSO−C196() users and TSO−C129() GPS users authorized for Class A1, A2, B1, B2, C1, or C2 operations may use GPS in place of another approved means of long−range navigation, such as dual INS. (See TBL 1−1−5 and TBL 1−1−6.) Aircraft with a single installation GPS, meeting the above specifications, are authorized to operate on short oceanic routes requiring one means of long−range navigation (reference AC 20-138, Appendix 1). 1−1−24 3/15/07 5/19/22 6/17/21 (b) Conduct GPS domestic, en route, and terminal IFR operations only when approved avionics systems are installed. Pilots may use GPS via TSO−C129() authorized for Class A1, B1, B3, C1, or C3 operations GPS via TSO-C196(); or GPS/WAAS with either TSO-C145() or TSO-C146(). When using TSO-C129() or TSO-C196() receivers, the avionics necessary to receive all of the ground−based facilities appropriate for the route to the destination airport and any required alternate airport must be installed and operational. Ground−based facilities necessary for these routes must be operational. (1) GPS en route IFR operations may be conducted in Alaska outside the operational service volume of ground−based navigation aids when a TSO−C145() or TSO−C146() GPS/wide area augmentation system (WAAS) system is installed and operating. WAAS is the U.S. version of a satellite-based augmentation system (SBAS). [a] In Alaska, aircraft may operate on GNSS Q-routes with GPS (TSO-C129 () or TSO-C196 ()) equipment while the aircraft remains in Air Traffic Control (ATC) radar surveillance or with GPS/WAAS (TSO-C145 () or TSO-C146 ()) which does not require ATC radar surveillance. [b] In Alaska, aircraft may only operate on GNSS T-routes with GPS/WAAS (TSO-C145 () or TSO-C146 ()) equipment. (2) Ground−based navigation equipment is not required to be installed and operating for en route IFR operations when using GPS/WAAS navigation systems. All operators should ensure that an alternate means of navigation is available in the unlikely event the GPS/WAAS navigation system becomes inoperative. (3) Q-routes and T-routes outside Alaska. Q-routes require system performance currently met by GPS, GPS/WAAS, or DME/DME/IRU RNAV systems that satisfy the criteria discussed in AC 90−100, U.S. Terminal and En Route Area Navigation (RNAV) Operations. T-routes require GPS or GPS/WAAS equipment. REFERENCE− AIM, Paragraph 5−3−4 , Airways and Route Systems (c) GPS IFR approach/departure operations can be conducted when approved avionics systems are installed and the following requirements are met: Navigation Aids 5/19/22 6/17/21 (1) The aircraft is TSO−C145() or TSO− C146() or TSO−C196() or TSO−C129() in Class A1, B1, B3, C1, or C3; and (2) The approach/departure must be retrievable from the current airborne navigation database in the navigation computer. The system must be able to retrieve the procedure by name from the aircraft navigation database. Manual entry of waypoints using latitude/longitude or place/bearing is not permitted for approach procedures. (3) The authorization to fly instrument approaches/departures with GPS is limited to U.S. airspace. (4) The use of GPS in any other airspace must be expressly authorized by the FAA Administrator. (5) GPS instrument approach/departure operations outside the U.S. must be authorized by the appropriate sovereign authority. 4. Departures and Instrument Departure Procedures (DPs) The GPS receiver must be set to terminal (±1 NM) CDI sensitivity and the navigation routes contained in the database in order to fly published IFR charted departures and DPs. Terminal RAIM should be automatically provided by the receiver. (Terminal RAIM for departure may not be available unless the waypoints are part of the active flight plan rather than proceeding direct to the first destination.) Certain segments of a DP may require some manual intervention by the pilot, especially when radar vectored to a course or required to intercept a specific course to a waypoint. The database may not contain all of the transitions or departures from all runways and some GPS receivers do not contain DPs in the database. It is necessary that helicopter procedures be flown at 70 knots or less since helicopter departure procedures and missed approaches use a 20:1 obstacle clearance surface (OCS), which is double the fixed−wing OCS, and turning areas are based on this speed as well. 5. GPS Instrument Approach Procedures (a) GPS overlay approaches are designated non−precision instrument approach procedures that pilots are authorized to fly using GPS avionics. Localizer (LOC), localizer type directional aid (LDA), and simplified directional facility (SDF) Navigation Aids AIM procedures are not authorized. Overlay procedures are identified by the “name of the procedure” and “or GPS” (e.g., VOR/DME or GPS RWY 15) in the title. Authorized procedures must be retrievable from a current onboard navigation database. The navigation database may also enhance position orientation by displaying a map containing information on conventional NAVAID approaches. This approach information should not be confused with a GPS overlay approach (see the receiver operating manual, AFM, or AFM Supplement for details on how to identify these approaches in the navigation database). NOTE− Overlay approaches do not adhere to the design criteria described in Paragraph 5−4−5m, Area Navigation (RNAV) Instrument Approach Charts, for stand−alone GPS approaches. Overlay approach criteria is based on the design criteria used for ground−based NAVAID approaches. (b) Stand−alone approach procedures specifically designed for GPS systems have replaced many of the original overlay approaches. All approaches that contain “GPS” in the title (e.g., “VOR or GPS RWY 24,” “GPS RWY 24,” or “RNAV (GPS) RWY 24”) can be flown using GPS. GPS−equipped aircraft do not need underlying ground−based NAVAIDs or associated aircraft avionics to fly the approach. Monitoring the underlying approach with ground−based NAVAIDs is suggested when able. Existing overlay approaches may be requested using the GPS title; for example, the VOR or GPS RWY 24 may be requested as “GPS RWY 24.” Some GPS procedures have a Terminal Arrival Area (TAA) with an underlining RNAV approach. (c) For flight planning purposes, TSO-C129() and TSO-C196()−equipped users (GPS users) whose navigation systems have fault detection and exclusion (FDE) capability, who perform a preflight RAIM prediction for the approach integrity at the airport where the RNAV (GPS) approach will be flown, and have proper knowledge and any required training and/or approval to conduct a GPS-based IAP, may file based on a GPS−based IAP at either the destination or the alternate airport, but not at both locations. At the alternate airport, pilots may plan for: (1) Lateral navigation (LNAV) or circling minimum descent altitude (MDA); 1−1−25 7110.65R CHG 2 AIM AIM (2) LNAV/vertical navigation (LNAV/ VNAV) DA, if equipped with and using approved barometric vertical navigation (baro-VNAV) equipment; (3) RNP 0.3 DA on an RNAV (RNP) IAP, if they are specifically authorized users using approved baro-VNAV equipment and the pilot has verified required navigation performance (RNP) availability through an approved prediction program. (d) If the above conditions cannot be met, any required alternate airport must have an approved instrument approach procedure other than GPS− based that is anticipated to be operational and available at the estimated time of arrival, and which the aircraft is equipped to fly. (e) Procedures for Accomplishing GPS Approaches (1) An RNAV (GPS) procedure may be associated with a Terminal Arrival Area (TAA). The basic design of the RNAV procedure is the “T” design or a modification of the “T” (See Paragraph 5-4-5d, Terminal Arrival Area (TAA), for complete information). (2) Pilots cleared by ATC for an RNAV (GPS) approach should fly the full approach from an Initial Approach Waypoint (IAWP) or feeder fix. Randomly joining an approach at an intermediate fix does not assure terrain clearance. (3) When an approach has been loaded in the navigation system, GPS receivers will give an “arm” annunciation 30 NM straight line distance from the airport/heliport reference point. Pilots should arm the approach mode at this time if not already armed (some receivers arm automatically). Without arming, the receiver will not change from en route CDI and RAIM sensitivity of ±5 NM either side of centerline to ±1 NM terminal sensitivity. Where the IAWP is inside this 30 mile point, a CDI sensitivity change will occur once the approach mode is armed and the aircraft is inside 30 NM. Where the IAWP is beyond 30 NM from the airport/heliport reference point and the approach is armed, the CDI sensitivity will not change until the aircraft is within 30 miles of the airport/heliport reference point. Feeder route obstacle clearance is predicated on the receiver being in terminal (±1 NM) CDI sensitivity and RAIM within 30 NM of the airport/heliport reference point; therefore, the receiver should always 1−1−26 3/15/07 5/19/22 6/17/21 be armed (if required) not later than the 30 NM annunciation. (4) The pilot must be aware of what bank angle/turn rate the particular receiver uses to compute turn anticipation, and whether wind and airspeed are included in the receiver’s calculations. This information should be in the receiver operating manual. Over or under banking the turn onto the final approach course may significantly delay getting on course and may result in high descent rates to achieve the next segment altitude. (5) When within 2 NM of the Final Approach Waypoint (FAWP) with the approach mode armed, the approach mode will switch to active, which results in RAIM and CDI changing to approach sensitivity. Beginning 2 NM prior to the FAWP, the full scale CDI sensitivity will smoothly change from ±1 NM to ±0.3 NM at the FAWP. As sensitivity changes from ±1 NM to ±0.3 NM approaching the FAWP, with the CDI not centered, the corresponding increase in CDI displacement may give the impression that the aircraft is moving further away from the intended course even though it is on an acceptable intercept heading. Referencing the digital track displacement information (cross track error), if it is available in the approach mode, may help the pilot remain position oriented in this situation. Being established on the final approach course prior to the beginning of the sensitivity change at 2 NM will help prevent problems in interpreting the CDI display during ramp down. Therefore, requesting or accepting vectors which will cause the aircraft to intercept the final approach course within 2 NM of the FAWP is not recommended. (6) When receiving vectors to final, most receiver operating manuals suggest placing the receiver in the non−sequencing mode on the FAWP and manually setting the course. This provides an extended final approach course in cases where the aircraft is vectored onto the final approach course outside of any existing segment which is aligned with the runway. Assigned altitudes must be maintained until established on a published segment of the approach. Required altitudes at waypoints outside the FAWP or stepdown fixes must be considered. Calculating the distance to the FAWP may be required in order to descend at the proper location. (7) Overriding an automatically selected sensitivity during an approach will cancel the approach mode annunciation. If the approach mode Navigation Aids 5/19/22 6/17/21 is not armed by 2 NM prior to the FAWP, the approach mode will not become active at 2 NM prior to the FAWP, and the equipment will flag. In these conditions, the RAIM and CDI sensitivity will not ramp down, and the pilot should not descend to MDA, but fly to the MAWP and execute a missed approach. The approach active annunciator and/or the receiver should be checked to ensure the approach mode is active prior to the FAWP. (8) Do not attempt to fly an approach unless the procedure in the onboard database is current and identified as “GPS” on the approach chart. The navigation database may contain information about non−overlay approach procedures that enhances position orientation generally by providing a map, while flying these approaches using conventional NAVAIDs. This approach information should not be confused with a GPS overlay approach (see the receiver operating manual, AFM, or AFM Supplement for details on how to identify these procedures in the navigation database). Flying point to point on the approach does not assure compliance with the published approach procedure. The proper RAIM sensitivity will not be available and the CDI sensitivity will not automatically change to ±0.3 NM. Manually setting CDI sensitivity does not automatically change the RAIM sensitivity on some receivers. Some existing non−precision approach procedures cannot be coded for use with GPS and will not be available as overlays. (9) Pilots should pay particular attention to the exact operation of their GPS receivers for performing holding patterns and in the case of overlay approaches, operations such as procedure turns. These procedures may require manual intervention by the pilot to stop the sequencing of waypoints by the receiver and to resume automatic GPS navigation sequencing once the maneuver is complete. The same waypoint may appear in the route of flight more than once consecutively (for example, IAWP, FAWP, MAHWP on a procedure turn). Care must be exercised to ensure that the receiver is sequenced to the appropriate waypoint for the segment of the procedure being flown, especially if one or more fly−overs are skipped (for example, FAWP rather than IAWP if the procedure turn is not flown). The pilot may have to sequence past one or more fly−overs of the same waypoint in order to start GPS automatic sequencing at the proper place in the sequence of waypoints. Navigation Aids AIM (10) Incorrect inputs into the GPS receiver are especially critical during approaches. In some cases, an incorrect entry can cause the receiver to leave the approach mode. (11) A fix on an overlay approach identified by a DME fix will not be in the waypoint sequence on the GPS receiver unless there is a published name assigned to it. When a name is assigned, the along track distance (ATD) to the waypoint may be zero rather than the DME stated on the approach chart. The pilot should be alert for this on any overlay procedure where the original approach used DME. (12) If a visual descent point (VDP) is published, it will not be included in the sequence of waypoints. Pilots are expected to use normal piloting techniques for beginning the visual descent, such as ATD. (13) Unnamed stepdown fixes in the final approach segment may or may not be coded in the waypoint sequence of the aircraft’s navigation database and must be identified using ATD. Stepdown fixes in the final approach segment of RNAV (GPS) approaches are being named, in addition to being identified by ATD. However, GPS avionics may or may not accommodate waypoints between the FAF and MAP. Pilots must know the capabilities of their GPS equipment and continue to identify stepdown fixes using ATD when necessary. (f) Missed Approach (1) A GPS missed approach requires pilot action to sequence the receiver past the MAWP to the missed approach portion of the procedure. The pilot must be thoroughly familiar with the activation procedure for the particular GPS receiver installed in the aircraft and must initiate appropriate action after the MAWP. Activating the missed approach prior to the MAWP will cause CDI sensitivity to immediately change to terminal (±1NM) sensitivity and the receiver will continue to navigate to the MAWP. The receiver will not sequence past the MAWP. Turns should not begin prior to the MAWP. If the missed approach is not activated, the GPS receiver will display an extension of the inbound final approach course and the ATD will increase from the MAWP until it is manually sequenced after crossing the MAWP. (2) Missed approach routings in which the first track is via a course rather than direct to the next 1−1−27 7110.65R CHG 2 AIM AIM waypoint require additional action by the pilot to set the course. Being familiar with all of the inputs required is especially critical during this phase of flight. (g) Receiver Autonomous Integrity Monitoring (RAIM) (1) RAIM outages may occur due to an insufficient number of satellites or due to unsuitable satellite geometry which causes the error in the position solution to become too large. Loss of satellite reception and RAIM warnings may occur due to aircraft dynamics (changes in pitch or bank angle). Antenna location on the aircraft, satellite position relative to the horizon, and aircraft attitude may affect reception of one or more satellites. Since the relative positions of the satellites are constantly changing, prior experience with the airport does not guarantee reception at all times, and RAIM availability should always be checked. (2) Civilian pilots may obtain GPS RAIM availability information for nonprecision approach procedures by using a manufacturer−supplied RAIM prediction tool, or using the Service Availability Prediction Tool (SAPT) on the FAA en route and terminal RAIM prediction website. Pilots can also request GPS RAIM aeronautical information from a flight service station during preflight briefings. GPS RAIM aeronautical information can be obtained for a period of 3 hours (for example, if you are scheduled to arrive at 1215 hours, then the GPS RAIM information is available from 1100 to 1400 hours) or a 24−hour timeframe at a particular airport. FAA briefers will provide RAIM information for a period of 1 hour before to 1 hour after the ETA hour, unless a specific timeframe is requested by the pilot. If flying a published GPS departure, a RAIM prediction should also be requested for the departure airport. (3) The military provides airfield specific GPS RAIM NOTAMs for nonprecision approach procedures at military airfields. The RAIM outages are issued as M−series NOTAMs and may be obtained for up to 24 hours from the time of request. (4) Receiver manufacturers and/or database suppliers may supply “NOTAM” type information concerning database errors. Pilots should check these sources when available, to ensure that they have the most current information concerning their electronic database. 1−1−28 3/15/07 5/19/22 6/17/21 (5) If RAIM is not available, use another type of navigation and approach system; select another route or destination; or delay the trip until RAIM is predicted to be available on arrival. On longer flights, pilots should consider rechecking the RAIM prediction for the destination during the flight. This may provide an early indication that an unscheduled satellite outage has occurred since takeoff. (6) If a RAIM failure/status annunciation occurs prior to the final approach waypoint (FAWP), the approach should not be completed since GPS no longer provides the required integrity. The receiver performs a RAIM prediction by 2 NM prior to the FAWP to ensure that RAIM is available as a condition for entering the approach mode. The pilot should ensure the receiver has sequenced from “Armed” to “Approach” prior to the FAWP (normally occurs 2 NM prior). Failure to sequence may be an indication of the detection of a satellite anomaly, failure to arm the receiver (if required), or other problems which preclude flying the approach. (7) If the receiver does not sequence into the approach mode or a RAIM failure/status annunciation occurs prior to the FAWP, the pilot must not initiate the approach nor descend, but instead, proceed to the missed approach waypoint (MAWP) via the FAWP, perform a missed approach, and contact ATC as soon as practical. The GPS receiver may continue to operate after a RAIM flag/status annunciation appears, but the navigation information should be considered advisory only. Refer to the receiver operating manual for specific indications and instructions associated with loss of RAIM prior to the FAF. (8) If the RAIM flag/status annunciation appears after the FAWP, the pilot should initiate a climb and execute the missed approach. The GPS receiver may continue to operate after a RAIM flag/status annunciation appears, but the navigation information should be considered advisory only. Refer to the receiver operating manual for operating mode information during a RAIM annunciation. (h) Waypoints (1) GPS receivers navigate from one defined point to another retrieved from the aircraft’s onboard navigational database. These points are waypoints (5-letter pronounceable name), existing VHF intersections, DME fixes with 5−letter Navigation Aids 5/19/22 6/17/21 pronounceable names and 3-letter NAVAID IDs. Each waypoint is a geographical location defined by a latitude/longitude geographic coordinate. These 5−letter waypoints, VHF intersections, 5−letter pronounceable DME fixes and 3−letter NAVAID IDs are published on various FAA aeronautical navigation products (IFR Enroute Charts, VFR Charts, Terminal Procedures Publications, etc.). (2) A Computer Navigation Fix (CNF) is also a point defined by a latitude/longitude coordinate and is required to support Performance−Based Navigation (PBN) operations. The GPS receiver uses CNFs in conjunction with waypoints to navigate from point to point. However, CNFs are not recognized by ATC. ATC does not maintain CNFs in their database and they do not use CNFs for any air traffic control purpose. CNFs may or may not be charted on FAA aeronautical navigation products, are listed in the chart legends, and are for advisory purposes only. Pilots are not to use CNFs for point to point navigation (proceed direct), filing a flight plan, or in aircraft/ATC communications. CNFs that do appear on aeronautical charts allow pilots increased situational awareness by identifying points in the aircraft database route of flight with points on the aeronautical chart. CNFs are random five-letter identifiers, not pronounceable like waypoints and placed in parenthesis. Eventually, all CNFs will begin with the letters “CF” followed by three consonants (for example, CFWBG). This five-letter identifier will be found next to an “x” on enroute charts and possibly on an approach chart. On instrument approach procedures (charts) in the terminal procedures publication, CNFs may represent unnamed DME fixes, beginning and ending points of DME arcs, and sensor (ground-based signal i.e., VOR, NDB, ILS) final approach fixes on GPS overlay approaches. These CNFs provide the GPS with points on the procedure that allow the overlay approach to mirror the ground-based sensor approach. These points should only be used by the GPS system for navigation and should not be used by pilots for any other purpose on the approach. The CNF concept has not been adopted or recognized by the International Civil Aviation Organization (ICAO). (3) GPS approaches use fly−over and fly−by waypoints to join route segments on an approach. Fly−by waypoints connect the two segments by allowing the aircraft to turn prior to the Navigation Aids AIM current waypoint in order to roll out on course to the next waypoint. This is known as turn anticipation and is compensated for in the airspace and terrain clearances. The missed approach waypoint (MAWP) will always be a fly−over waypoint. A holding waypoint will always be designed as a fly−over waypoint in the navigational database but may be charted as a fly−by event unless the holding waypoint is used for another purpose in the procedure and both events require the waypoint to be a fly−over event. Some waypoints may have dual use; for example, as a fly−by waypoint when used as an IF for a NoPT route and as a fly−over waypoint when the same waypoint is also used as an IAF/IF hold−in−lieu of PT. Since the waypoint can only be charted one way, when this situation occurs, the fly−by waypoint symbol will be charted in all uses of the waypoint. (4) Unnamed waypoints for each airport will be uniquely identified in the database. Although the identifier may be used at different airports (for example, RW36 will be the identifier at each airport with a runway 36), the actual point, at each airport, is defined by a specific latitude/longitude coordinate. (5) The runway threshold waypoint, normally the MAWP, may have a five−letter identifier (for example, SNEEZ) or be coded as RW## (for example, RW36, RW36L). MAWPs located at the runway threshold are being changed to the RW## identifier, while MAWPs not located at the threshold will have a five−letter identifier. This may cause the approach chart to differ from the aircraft database until all changes are complete. The runway threshold waypoint is also used as the center of the Minimum Safe Altitude (MSA) on most GPS approaches. (i) Position Orientation. Pilots should pay particular attention to position orientation while using GPS. Distance and track information are provided to the next active waypoint, not to a fixed navigation aid. Receivers may sequence when the pilot is not flying along an active route, such as when being vectored or deviating for weather, due to the proximity to another waypoint in the route. This can be prevented by placing the receiver in the non-sequencing mode. When the receiver is in the non-sequencing mode, bearing and distance are provided to the selected waypoint and the receiver will not sequence to the next waypoint in the route until placed back in the auto sequence mode or the pilot selects a different waypoint. The pilot may have to compute the ATD 1−1−29 7110.65R CHG 2 AIM AIM to stepdown fixes and other points on overlay approaches, due to the receiver showing ATD to the next waypoint rather than DME to the VOR or ILS ground station. (j) Impact of Magnetic Variation on PBN Systems (1) Differences may exist between PBN systems and the charted magnetic courses on ground−based NAVAID instrument flight procedures (IFP), enroute charts, approach charts, and Standard Instrument Departure/Standard Terminal Arrival (SID/STAR) charts. These differences are due to the magnetic variance used to calculate the magnetic course. Every leg of an instrument procedure is first computed along a desired ground track with reference to true north. A magnetic variation correction is then applied to the true course in order to calculate a magnetic course for publication. The type of procedure will determine what magnetic variation value is added to the true course. A ground−based NAVAID IFP applies the facility magnetic variation of record to the true course to get the charted magnetic course. Magnetic courses on PBN procedures are calculated two different ways. SID/STAR procedures use the airport magnetic variation of record, while IFR enroute charts use magnetic reference bearing. PBN systems make a correction to true north by adding a magnetic variation calculated with an algorithm based on aircraft position, or by adding the magnetic variation coded in their navigational database. This may result in the PBN system and the procedure designer using a different magnetic variation, which causes the magnetic course displayed by the PBN system and the magnetic course charted on the IFP plate to be different. It is important to understand, however, that PBN systems, (with the exception of VOR/DME RNAV equipment) navigate by reference to true north and display magnetic course only for pilot reference. As such, a properly functioning PBN system, containing a current and accurate navigational database, should fly the correct ground track for any loaded instrument procedure, despite differences in displayed magnetic course that may be attributed to magnetic variation application. Should significant differences between the approach chart and the PBN system avionics’ application of the navigation database arise, the published approach chart, supplemented by NOTAMs, holds precedence. 1−1−30 3/15/07 5/19/22 6/17/21 (2) The course into a waypoint may not always be 180 degrees different from the course leaving the previous waypoint, due to the PBN system avionics’ computation of geodesic paths, distance between waypoints, and differences in magnetic variation application. Variations in distances may also occur since PBN system distance−to−waypoint values are ATDs computed to the next waypoint and the DME values published on underlying procedures are slant−range distances measured to the station. This difference increases with aircraft altitude and proximity to the NAVAID. (k) GPS Familiarization Pilots should practice GPS approaches in visual meteorological conditions (VMC) until thoroughly proficient with all aspects of their equipment (receiver and installation) prior to attempting flight in instrument meteorological conditions (IMC). Pilots should be proficient in the following areas: (1) Using the receiver autonomous integrity monitoring (RAIM) prediction function; (2) Inserting a DP into the flight plan, including setting terminal CDI sensitivity, if required, and the conditions under which terminal RAIM is available for departure; (3) Programming the destination airport; (4) Programming and flying the approaches (especially procedure turns and arcs); (5) Changing to another approach after selecting an approach; (6) Programming and flying “direct” missed approaches; (7) Programming and flying “routed” missed approaches; (8) Entering, flying, and exiting holding patterns, particularly on approaches with a second waypoint in the holding pattern; (9) Programming and flying a “route” from a holding pattern; (10) Programming and flying an approach with radar vectors to the intermediate segment; (11) Indication of the actions required for RAIM failure both before and after the FAWP; and (12) Programming a radial and distance from a VOR (often used in departure instructions). Navigation Aids 5/19/22 6/17/21 AIM TBL 1−1−5 GPS IFR Equipment Classes/Categories TSO−C129 Equipment Class RAIM Int. Nav. Sys. to Prov. RAIM Equiv. Oceanic En Route Terminal Non−precision Approach Capable yes yes yes yes yes yes yes no Class A − GPS sensor and navigation capability. A1 A2 yes yes Class B − GPS sensor data to an integrated navigation system (i.e., FMS, multi−sensor navigation system, etc.). B1 B2 B3 B4 yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes no yes no Class C − GPS sensor data to an integrated navigation system (as in Class B) which provides enhanced guidance to an autopilot, or flight director, to reduce flight tech. errors. Limited to 14 CFR Part 121 or equivalent criteria. C1 C2 C3 C4 yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes no yes no TBL 1−1−6 GPS Approval Required/Authorized Use Equipment Type1 Installation Approval Required Operational Approval Required IFR En Route2 IFR Terminal2 Hand held4 X5 VFR Panel Mount4 X IFR En Route and Terminal X X X X IFR Oceanic/ Remote X X X X IFR En Route, Terminal, and Approach X X X X IFR Approach3 Oceanic Remote In Lieu of ADF and/or DME3 X X X X X NOTE− 1To determine equipment approvals and limitations, refer to the AFM, AFM supplements, or pilot guides. 2Requires verification of data for correctness if database is expired. 3Requires current database or verification that the procedure has not been amended since the expiration of the database. 4VFR and hand−held GPS systems are not authorized for IFR navigation, instrument approaches, or as a primary instrument flight reference. During IFR operations they may be considered only an aid to situational awareness. 5Hand−held receivers require no approval. However, any aircraft modification to support the hand−held receiver; i.e., installation of an external antenna or a permanent mounting bracket, does require approval. Navigation Aids 1−1−31 7110.65R CHG 2 AIM AIM 1−1−18. Wide Area Augmentation System (WAAS) a. General 1. The FAA developed the WAAS to improve the accuracy, integrity and availability of GPS signals. WAAS will allow GPS to be used, as the aviation navigation system, from takeoff through approach when it is complete. WAAS is a critical component of the FAA’s strategic objective for a seamless satellite navigation system for civil aviation, improving capacity and safety. 2. The International Civil Aviation Organization (ICAO) has defined Standards and Recommended Practices (SARPs) for satellite−based augmentation systems (SBAS) such as WAAS. India and Europe are building similar systems: EGNOS, the European Geostationary Navigation Overlay System; and India’s GPS and Geo−Augmented Navigation (GAGAN) system. The merging of these systems will create an expansive navigation capability similar to GPS, but with greater accuracy, availability, and integrity. 3. Unlike traditional ground−based navigation aids, WAAS will cover a more extensive service area. Precisely surveyed wide−area reference stations (WRS) are linked to form the U.S. WAAS network. Signals from the GPS satellites are monitored by these WRSs to determine satellite clock and ephemeris corrections and to model the propagation effects of the ionosphere. Each station in the network relays the data to a wide−area master station (WMS) where the correction information is computed. A correction message is prepared and uplinked to a geostationary earth orbit satellite (GEO) via a GEO uplink subsystem (GUS) which is located at the ground earth station (GES). The message is then broadcast on the same frequency as GPS (L1, 1575.42 MHz) to WAAS receivers within the broadcast coverage area of the WAAS GEO. 4. In addition to providing the correction signal, the WAAS GEO provides an additional pseudorange measurement to the aircraft receiver, improving the availability of GPS by providing, in effect, an additional GPS satellite in view. The integrity of GPS is improved through real−time monitoring, and the accuracy is improved by providing differential corrections to reduce errors. The performance improvement is sufficient to enable approach 1−1−32 3/15/07 5/19/22 6/17/21 procedures with GPS/WAAS glide paths (vertical guidance). 5. The FAA has completed installation of 3 GEO satellite links, 38 WRSs, 3 WMSs, 6 GES, and the required terrestrial communications to support the WAAS network including 2 operational control centers. Prior to the commissioning of the WAAS for public use, the FAA conducted a series of test and validation activities. Future dual frequency operations are planned. 6. GNSS navigation, including GPS and WAAS, is referenced to the WGS−84 coordinate system. It should only be used where the Aeronautical Information Publications (including electronic data and aeronautical charts) conform to WGS−84 or equivalent. Other countries’ civil aviation authorities may impose additional limitations on the use of their SBAS systems. b. Instrument Approach Capabilities 1. A class of approach procedures which provide vertical guidance, but which do not meet the ICAO Annex 10 requirements for precision approaches has been developed to support satellite navigation use for aviation applications worldwide. These procedures are not precision and are referred to as Approach with Vertical Guidance (APV), are defined in ICAO Annex 6, and include approaches such as the LNAV/VNAV and localizer performance with vertical guidance (LPV). These approaches provide vertical guidance, but do not meet the more stringent standards of a precision approach. Properly certified WAAS receivers will be able to fly to LPV minima and LNAV/VNAV minima, using a WAAS electronic glide path, which eliminates the errors that can be introduced by using Barometric altimetry. 2. LPV minima takes advantage of the high accuracy guidance and increased integrity provided by WAAS. This WAAS generated angular guidance allows the use of the same TERPS approach criteria used for ILS approaches. LPV minima may have a decision altitude as low as 200 feet height above touchdown with visibility minimums as low as 1/2 mile, when the terrain and airport infrastructure support the lowest minima. LPV minima is published on the RNAV (GPS) approach charts (see paragraph 5−4−5, Instrument Approach Procedure Charts). 3. A different WAAS-based line of minima, called Localizer Performance (LP) is being added in locations where the terrain or obstructions do not Navigation Aids 5/19/22 12/2/21 6/17/21 allow publication of vertically guided LPV minima. LP takes advantage of the angular lateral guidance and smaller position errors provided by WAAS to provide a lateral only procedure similar to an ILS Localizer. LP procedures may provide lower minima than a LNAV procedure due to the narrower obstacle clearance surface. NOTE− WAAS receivers certified prior to TSO−C145b and TSO−C146b, even if they have LPV capability, do not contain LP capability unless the receiver has been upgraded. Receivers capable of flying LP procedures must contain a statement in the Aircraft Flight Manual (AFM), AFM Supplement, or Approved Supplemental Flight Manual stating that the receiver has LP capability, as well as the capability for the other WAAS and GPS approach procedure types. 4. WAAS provides a level of service that supports all phases of flight, including RNAV (GPS) approaches to LNAV, LP, LNAV/VNAV, and LPV lines of minima, within system coverage. Some locations close to the edge of the coverage may have a lower availability of vertical guidance. c. General Requirements 1. WAAS avionics must be certified in accordance with Technical Standard Order (TSO) TSO−C145(), Airborne Navigation Sensors Using the (GPS) Augmented by the Wide Area Augmentation System (WAAS); or TSO−C146(), Stand−Alone Airborne Navigation Equipment Using the Global Positioning System (GPS) Augmented by the Wide Area Augmentation System (WAAS), and installed in accordance with AC 20−138, Airworthiness Approval of Positioning and Navigation Systems. 2. GPS/WAAS operation must be conducted in accordance with the FAA−approved aircraft flight manual (AFM) and flight manual supplements. Flight manual supplements will state the level of approach procedure that the receiver supports. IFR approved WAAS receivers support all GPS only operations as long as lateral capability at the appropriate level is functional. WAAS monitors both GPS and WAAS satellites and provides integrity. 3. GPS/WAAS equipment is inherently capable of supporting oceanic and remote operations if the operator obtains a fault detection and exclusion (FDE) prediction program. Navigation Aids AIM 4. Air carrier and commercial operators must meet the appropriate provisions of their approved operations specifications. 5. Prior to GPS/WAAS IFR operation, the pilot must review appropriate Notices to Air Missions (NOTAMs) and aeronautical information. This information is available on request from a Flight Service Station. The FAA will provide NOTAMs to advise pilots of the status of the WAAS and level of service available. (a) The term MAY NOT BE AVBL is used in conjunction with WAAS NOTAMs and indicates that due to ionospheric conditions, lateral guidance may still be available when vertical guidance is unavailable. Under certain conditions, both lateral and vertical guidance may be unavailable. This NOTAM language is an advisory to pilots indicating the expected level of WAAS service (LNAV/VNAV, LPV, LP) may not be available. EXAMPLE− !FDC FDC NAV WAAS VNAV/LPV/LP MINIMA MAY NOT BE AVBL 1306111330-1306141930EST or !FDC FDC NAV WAAS VNAV/LPV MINIMA NOT AVBL, WAAS LP MINIMA MAY NOT BE AVBL 1306021200-1306031200EST WAAS MAY NOT BE AVBL NOTAMs are predictive in nature and published for flight planning purposes. Upon commencing an approach at locations NOTAMed WAAS MAY NOT BE AVBL, if the WAAS avionics indicate LNAV/VNAV or LPV service is available, then vertical guidance may be used to complete the approach using the displayed level of service. Should an outage occur during the approach, reversion to LNAV minima or an alternate instrument approach procedure may be required. When GPS testing NOTAMS are published and testing is actually occurring, Air Traffic Control will advise pilots requesting or cleared for a GPS or RNAV (GPS) approach that GPS may not be available and request intentions. If pilots have reported GPS anomalies, Air Traffic Control will request the pilot’s intentions and/or clear the pilot for an alternate approach, if available and operational. (b) WAAS area-wide NOTAMs are originated when WAAS assets are out of service and impact the service area. Area−wide WAAS NOT AVAILABLE (AVBL) NOTAMs indicate loss or malfunction of the WAAS system. In flight, Air Traffic Control will advise pilots requesting a GPS or 1−1−33 7110.65R CHG 2 AIM AIM RNAV (GPS) approach of WAAS NOT AVBL NOTAMs if not contained in the ATIS broadcast. EXAMPLE− For unscheduled loss of signal or service, an example NOTAM is: !FDC FDC NAV WAAS NOT AVBL 1311160600− 1311191200EST. For scheduled loss of signal or service, an example NOTAM is: !FDC FDC NAV WAAS NOT AVBL 1312041015- 1312082000EST. (c) Site−specific WAAS MAY NOT BE AVBL NOTAMs indicate an expected level of service; for example, LNAV/VNAV, LP, or LPV may not be available. Pilots must request site−specific WAAS NOTAMs during flight planning. In flight, Air Traffic Control will not advise pilots of WAAS MAY NOT BE AVBL NOTAMs. NOTE− Though currently unavailable, the FAA is updating its prediction tool software to provide this site-service in the future. (d) Most of North America has redundant coverage by two or more geostationary satellites. One exception is the northern slope of Alaska. If there is a problem with the satellite providing coverage to this area, a NOTAM similar to the following example will be issued: EXAMPLE− !FDC 4/3406 (PAZA A0173/14) ZAN NAV WAAS SIGNAL MAY NOT BE AVBL NORTH OF LINE FROM 7000N150000W TO 6400N16400W. RMK WAAS USERS SHOULD CONFIRM RAIM AVAILABILITY FOR IFR OPERATIONS IN THIS AREA. T-ROUTES IN THIS SECTOR NOT AVBL. ANY REQUIRED ALTERNATE AIRPORT IN THIS AREA MUST HAVE AN APPROVED INSTRUMENT APPROACH PROCEDURE OTHER THAN GPS THAT IS ANTICIPATED TO BE OPERATIONAL AND AVAILABLE AT THE ESTIMATED TIME OF ARRIVAL AND WHICH THE AIRCRAFT IS EQUIPPED TO FLY. 1406030812-1406050812EST . 6. When GPS−testing NOTAMS are published and testing is actually occurring, Air Traffic Control will advise pilots requesting or cleared for a GPS or RNAV (GPS) approach that GPS may not be available and request intentions. If pilots have reported GPS anomalies, Air Traffic Control will request the pilot’s intentions and/or clear the pilot for an alternate approach, if available and operational. EXAMPLE− Here is an example of a GPS testing NOTAM: !GPS 06/001 ZAB NAV GPS (INCLUDING WAAS, GBAS, 1−1−34 3/15/07 5/19/22 6/17/21 AND ADS-B) MAY NOT BE AVAILABLE WITHIN A 468NM RADIUS CENTERED AT 330702N1062540W (TCS 093044) FL400-UNL DECREASING IN AREA WITH A DECREASE IN ALTITUDE DEFINED AS: 425NM RADIUS AT FL250, 360NM RADIUS AT 10000FT, 354NM RADIUS AT 4000FT AGL, 327NM RADIUS AT 50FT AGL. 1406070300-1406071200. 7. When the approach chart is annotated with the symbol, site−specific WAAS MAY NOT BE AVBL NOTAMs or Air Traffic advisories are not provided for outages in WAAS LNAV/VNAV and LPV vertical service. Vertical outages may occur daily at these locations due to being close to the edge of WAAS system coverage. Use LNAV or circling minima for flight planning at these locations, whether as a destination or alternate. For flight operations at these locations, when the WAAS avionics indicate that LNAV/VNAV or LPV service is available, then the vertical guidance may be used to complete the approach using the displayed level of service. Should an outage occur during the procedure, reversion to LNAV minima may be required. NOTE− Area−wide WAAS NOT AVBL NOTAMs apply to all airports in the WAAS NOT AVBL area designated in the NOTAM, including approaches at airports where an symbol. approach chart is annotated with the 8. GPS/WAAS was developed to be used within GEO coverage over North America without the need for other radio navigation equipment appropriate to the route of flight to be flown. Outside the WAAS coverage or in the event of a WAAS failure, GPS/WAAS equipment reverts to GPS−only operation and satisfies the requirements for basic GPS equipment. (See paragraph 1−1−17 for these requirements). 9. Unlike TSO−C129 avionics, which were certified as a supplement to other means of navigation, WAAS avionics are evaluated without reliance on other navigation systems. As such, installation of WAAS avionics does not require the aircraft to have other equipment appropriate to the route to be flown. (See paragraph 1−1−17 d for more information on equipment requirements.) (a) Pilots with WAAS receivers may flight plan to use any instrument approach procedure authorized for use with their WAAS avionics as the planned approach at a required alternate, with the following restrictions. When using WAAS at an alternate airport, flight planning must be based Navigation Aids 5/19/22 6/17/21 on flying the RNAV (GPS) LNAV or circling minima line, or minima on a GPS approach procedure, or conventional approach procedure with “or GPS” in the title. Code of Federal Regulation (CFR) Part 91 non−precision weather requirements must be used for planning. Upon arrival at an alternate, when the WAAS navigation system indicates that LNAV/ VNAV or LPV service is available, then vertical guidance may be used to complete the approach using the displayed level of service. The FAA has begun NA (Alternate Minimums Not removing the Authorized) symbol from select RNAV (GPS) and GPS approach procedures so they may be used by approach approved WAAS receivers at alternate airports. Some approach procedures will still require NA for other reasons, such as no weather the reporting, so it cannot be removed from all procedures. Since every procedure must be individuNA from RNAV ally evaluated, removal of the (GPS) and GPS procedures will take some time. NOTE− Properly trained and approved, as required, TSO-C145() and TSO-C146() equipped users (WAAS users) with and using approved baro-VNAV equipment may plan for LNAV/VNAV DA at an alternate airport. Specifically authorized WAAS users with and using approved baro-VNAV equipment may also plan for RNP 0.3 DA at the alternate airport as long as the pilot has verified RNP availability through an approved prediction program. d. Flying Procedures with WAAS 1. WAAS receivers support all basic GPS approach functions and provide additional capabilities. One of the major improvements is the ability to generate glide path guidance, independent of ground equipment or barometric aiding. This eliminates several problems such as hot and cold temperature effects, incorrect altimeter setting, or lack of a local altimeter source. It also allows approach procedures to be built without the cost of installing ground stations at each airport or runway. Some approach certified receivers may only generate a glide path with performance similar to Baro−VNAV and are only approved to fly the LNAV/VNAV line of minima on the RNAV (GPS) approach charts. Receivers with additional capability (including faster update rates and smaller integrity limits) are approved to fly the LPV line of minima. The lateral integrity changes dramatically from the 0.3 NM (556 meter) limit for GPS, LNAV, and LNAV/VNAV approach mode, to 40 meters for LPV. It also provides vertical integrity Navigation Aids AIM monitoring, which bounds the vertical error to 50 meters for LNAV/VNAV and LPVs with minima of 250’ or above, and bounds the vertical error to 35 meters for LPVs with minima below 250’. 2. When an approach procedure is selected and active, the receiver will notify the pilot of the most accurate level of service supported by the combination of the WAAS signal, the receiver, and the selected approach, using the naming conventions on the minima lines of the selected approach procedure. For example, if an approach is published with LPV minima and the receiver is only certified for LNAV/VNAV, the equipment would indicate “LNAV/VNAV available,” even though the WAAS signal would support LPV. If flying an existing LNAV/VNAV procedure with no LPV minima, the receiver will notify the pilot “LNAV/VNAV available,” even if the receiver is certified for LPV and the signal supports LPV. If the signal does not support vertical guidance on procedures with LPV and/or LNAV/VNAV minima, the receiver annunciation will read “LNAV available.” On lateral only procedures with LP and LNAV minima the receiver will indicate “LP available” or “LNAV available” based on the level of lateral service available. Once the level of service notification has been given, the receiver will operate in this mode for the duration of the approach procedure, unless that level of service becomes unavailable. The receiver cannot change back to a more accurate level of service until the next time an approach is activated. NOTE− Receivers do not “fail down” to lower levels of service once the approach has been activated. If only the vertical off flag appears, the pilot may elect to use the LNAV minima if the rules under which the flight is operating allow changing the type of approach being flown after commencing the procedure. If the lateral integrity limit is exceeded on an LP approach, a missed approach will be necessary since there is no way to reset the lateral alarm limit while the approach is active. 3. Another additional feature of WAAS receivers is the ability to exclude a bad GPS signal and continue operating normally. This is normally accomplished by the WAAS correction information. Outside WAAS coverage or when WAAS is not available, it is accomplished through a receiver algorithm called FDE. In most cases this operation will be invisible to the pilot since the receiver will continue to operate with other available satellites 1−1−35 7110.65R CHG 2 AIM AIM after excluding the “bad” signal. This capability increases the reliability of navigation. 4. Both lateral and vertical scaling for the LNAV/VNAV and LPV approach procedures are different than the linear scaling of basic GPS. When the complete published procedure is flown, ±1 NM linear scaling is provided until two (2) NM prior to the FAF, where the sensitivity increases to be similar to the angular scaling of an ILS. There are two differences in the WAAS scaling and ILS: 1) on long final approach segments, the initial scaling will be ±0.3 NM to achieve equivalent performance to GPS (and better than ILS, which is less sensitive far from the runway); 2) close to the runway threshold, the scaling changes to linear instead of continuing to become more sensitive. The width of the final approach course is tailored so that the total width is usually 700 feet at the runway threshold. Since the origin point of the lateral splay for the angular portion of the final is not fixed due to antenna placement like localizer, the splay angle can remain fixed, making a consistent width of final for aircraft being vectored onto the final approach course on different length runways. When the complete published procedure is not flown, and instead the aircraft needs to capture the extended final approach course similar to ILS, the vector to final (VTF) mode is used. Under VTF, the scaling is linear at ±1 NM until the point where the ILS angular splay reaches a width of ±1 NM regardless of the distance from the FAWP. 5. The WAAS scaling is also different than GPS TSO−C129() in the initial portion of the missed approach. Two differences occur here. First, the scaling abruptly changes from the approach scaling to the missed approach scaling, at approximately the departure end of the runway or when the pilot selects missed approach guidance rather than ramping as GPS does. Second, when the first leg of the missed approach is a Track to Fix (TF) leg aligned within 3 degrees of the inbound course, the receiver will change to 0.3 NM linear sensitivity until the turn initiation point for the first waypoint in the missed approach procedure, at which time it will abruptly change to terminal (±1 NM) sensitivity. This allows the elimination of close in obstacles in the early part of the missed approach that may otherwise cause the DA to be raised. 6. There are two ways to select the final approach segment of an instrument approach. Most 1−1−36 3/15/07 5/19/22 6/17/21 receivers use menus where the pilot selects the airport, the runway, the specific approach procedure and finally the IAF, there is also a channel number selection method. The pilot enters a unique 5−digit number provided on the approach chart, and the receiver recalls the matching final approach segment from the aircraft database. A list of information including the available IAFs is displayed and the pilot selects the appropriate IAF. The pilot should confirm that the correct final approach segment was loaded by cross checking the Approach ID, which is also provided on the approach chart. 7. The Along−Track Distance (ATD) during the final approach segment of an LNAV procedure (with a minimum descent altitude) will be to the MAWP. On LNAV/VNAV and LPV approaches to a decision altitude, there is no missed approach waypoint so the along−track distance is displayed to a point normally located at the runway threshold. In most cases, the MAWP for the LNAV approach is located on the runway threshold at the centerline, so these distances will be the same. This distance will always vary slightly from any ILS DME that may be present, since the ILS DME is located further down the runway. Initiation of the missed approach on the LNAV/ VNAV and LPV approaches is still based on reaching the decision altitude without any of the items listed in 14 CFR Section 91.175 being visible, and must not be delayed while waiting for the ATD to reach zero. The WAAS receiver, unlike a GPS receiver, will automatically sequence past the MAWP if the missed approach procedure has been designed for RNAV. The pilot may also select missed approach prior to the MAWP; however, navigation will continue to the MAWP prior to waypoint sequencing taking place. 1−1−19. Ground Based Augmentation System (GBAS) Landing System (GLS) a. A GBAS ground installation at an airport can provide localized, differential augmentation to the Global Positioning System (GPS) signal−in−space enabling an aircraft’s GLS precision approach capability. Through the GBAS service and the aircraft’s GLS installation a pilot may complete an instrument approach offering three−dimensional angular, lateral, and vertical guidance for exact alignment and descent to a runway. The operational benefits of a GLS approach are similar to the benefits of an ILS or LPV approach operation. Navigation Aids 5/19/22 6/17/21 NOTE− To remain consistent with international terminology, the FAA will use the term GBAS in place of the former term Local Area Augmentation System (LAAS). b. An aircraft’s GLS approach capability relies on the broadcast from a GBAS Ground Facility (GGF) installation. The GGF installation includes at least four ground reference stations near the airport’s runway(s), a corrections processor, and a VHF Data Broadcast (VDB) uplink antenna. To use the GBAS GGF output and be eligible to conduct a GLS approach, the aircraft requires eligibility to conduct RNP approach (RNP APCH) operations and must meet the additional, specific airworthiness requirements for installation of a GBAS receiver intended to support GLS approach operations. When the aircraft achieves GLS approach eligibility, the aircraft’s onboard navigation database may then contain published GLS instrument approach procedures. c. During a GLS instrument approach procedure, the installation of an aircraft’s GLS capability provides the pilot three−dimensional (3D) lateral and vertical navigation guidance much like an ILS instrument approach. GBAS corrections augment the GPS signal−in−space by offering position corrections, ensures the availability of enhanced integrity parameters, and then transmits the actual approach path definition over the VDB uplink antenna. A single GBAS ground station can support multiple GLS approaches to one or more runways. d. Through the GBAS ground station, a GLS approach offers a unique operational service volume distinct from the traditional ILS approach service volume (see FIG 1−1−9). However, despite the unique service volume, in the final approach Navigation Aids AIM segment, a GLS approach provides precise 3D angular lateral and vertical guidance mimicking the precision guidance of an ILS approach. e. Transitions to and segments of the published GLS instrument approach procedures may rely on use of RNAV 1 or RNP 1 prior to an IAF. Then, during the approach procedure, prior to the aircraft entering the GLS approach mode, a GLS approach procedure design uses the RNP APCH procedure design criteria to construct the procedural path (the criteria used to publish procedures titled “RNAV (GPS)” in the US). Thus, a GLS approach procedure may include paths requiring turns after the aircraft crosses the IAF, prior to the aircraft’s flight guidance entering the GLS approach flight guidance mode. Likewise, the missed approach procedure for a GLS approach procedure relies exclusively on the same missed approach criteria supporting an RNP APCH. f. When maneuvering the aircraft in compliance with an ATC clearance to intercept a GLS approach prior to the final approach segment (e.g. “being vectored”), the pilot should adhere to the clearance and ensure the aircraft intercepts the extended GLS final approach course within the specified service volume. Once on the GLS final approach course, the pilot should ensure the aircraft is in the GLS approach mode prior to reaching the procedure’s glidepath intercept point. Once the aircraft is in the GLS flight guidance mode and captures the GLS glidepath, the pilot should fly the GLS final approach segment using the same pilot techniques they use to fly an ILS final approach or the final approach of an RNAV (GPS) approach flown to LPV minimums. See also the Instrument Procedures Handbook for more information on how to conduct a GLS instrument approach procedure. 1−1−37 7110.65R CHG 2 AIM AIM 3/15/07 5/19/22 6/17/21 FIG 1−1−9 GLS Standard Approach Service Volume 1−1−20. Precision Approach Systems other than ILS and GLS a. General Approval and use of precision approach systems other than ILS and GLS require the issuance of special instrument approach procedures. b. Special Instrument Approach Procedure 1. Special instrument approach procedures must be issued to the aircraft operator if pilot training, aircraft equipment, and/or aircraft performance is different than published procedures. Special instrument approach procedures are not distributed for general public use. These procedures are issued to an aircraft operator when the conditions for operations approval are satisfied. 1−1−38 2. General aviation operators requesting approval for special procedures should contact the local Flight Standards District Office to obtain a letter of authorization. Air carrier operators requesting approval for use of special procedures should contact their Certificate Holding District Office for authorization through their Operations Specification. c. Transponder Landing System (TLS) 1. The TLS is designed to provide approach guidance utilizing existing airborne ILS localizer, glide slope, and transponder equipment. 2. Ground equipment consists of a transponder interrogator, sensor arrays to detect lateral and vertical position, and ILS frequency transmitters. The TLS detects the aircraft’s position by interrogating its transponder. It then broadcasts ILS frequency signals to guide the aircraft along the desired approach path. Navigation Aids 5/19/22 6/17/21 3. TLS instrument approach procedures are designated Special Instrument Approach Procedures. Special aircrew training is required. TLS ground equipment provides approach guidance for only one aircraft at a time. Even though the TLS signal is received using the ILS receiver, no fixed course or glidepath is generated. The concept of operation is very similar to an air traffic controller providing radar vectors, and just as with radar vectors, the guidance is valid only for the intended aircraft. The TLS ground equipment tracks one aircraft, based on its transponder code, and provides correction signals to course and glidepath based on the position of the tracked aircraft. Flying the TLS corrections computed for another aircraft will not provide guidance relative to the approach; therefore, aircrews must not use the TLS signal for navigation unless they have received approach clearance and completed the required coordination with the TLS ground equipment operator. Navigation fixes based on conventional NAVAIDs or GPS are provided in the Navigation Aids AIM special instrument approach procedure to allow aircrews to verify the TLS guidance. d. Special Category I Differential GPS (SCAT− I DGPS) 1. The SCAT−I DGPS is designed to provide approach guidance by broadcasting differential correction to GPS. 2. SCAT−I DGPS procedures require aircraft equipment and pilot training. 3. Ground equipment consists of GPS receivers and a VHF digital radio transmitter. The SCAT−I DGPS detects the position of GPS satellites relative to GPS receiver equipment and broadcasts differential corrections over the VHF digital radio. 4. Category I Ground Based Augmentation System (GBAS) will displace SCAT−I DGPS as the public use service. REFERENCE− AIM, Paragraph 5−4−7 j, Instrument Approach Procedures. 1−1−39 6/17/21 AIM Section 2. Performance−Based Navigation (PBN) and Area Navigation (RNAV) 1−2−1. General a. Introduction to PBN. As air travel has evolved, methods of navigation have improved to give operators more flexibility. PBN exists under the umbrella of area navigation (RNAV). The term RNAV in this context, as in procedure titles, just means “area navigation,” regardless of the equipment capability of the aircraft. (See FIG 1−2−1.) Many operators have upgraded their systems to obtain the benefits of PBN. Within PBN there are two main categories of navigation methods or specifications: area navigation (RNAV) and required navigation performance (RNP). In this context, the term RNAV x means a specific navigation specification with a specified lateral accuracy value. For an aircraft to meet the requirements of PBN, a specified RNAV or RNP accuracy must be met 95 percent of the flight time. RNP is a PBN system that includes onboard performance monitoring and alerting capability (for example, Receiver Autonomous Integrity Monitoring (RAIM)). PBN also introduces the concept of navigation specifications (NavSpecs) which are a set of aircraft and aircrew requirements needed to support a navigation application within a defined airspace concept. For both RNP and RNAV NavSpecs, the numerical designation refers to the lateral navigation accuracy in nautical miles which is expected to be achieved at least 95 percent of the flight time by the population of aircraft operating within the airspace, route, or procedure. This information is detailed in International Civil Aviation Organization’s (ICAO) Doc 9613, Performance− based Navigation (PBN) Manual and the latest FAA AC 90−105, Approval Guidance for RNP Operations and Barometric Vertical Navigation in the U.S. National Airspace System and in Remote and Oceanic Airspace. FIG 1−2−1 Navigation Specifications Performance−Based Navigation (PBN) and Area Navigation (RNAV) 1−2−1 AIM 6/17/21 b. Area Navigation (RNAV) 1. General. RNAV is a method of navigation that permits aircraft operation on any desired flight path within the coverage of ground− or space−based navigation aids or within the limits of the capability of self−contained aids, or a combination of these. In the future, there will be an increased dependence on the use of RNAV in lieu of routes defined by ground−based navigation aids. RNAV routes and terminal procedures, including departure procedures (DPs) and standard terminal arrivals (STARs), are designed with RNAV systems in mind. There are several potential advantages of RNAV routes and procedures: the two route segments. This is known as turn anticipation. (2) Fly−over waypoints. Fly−over waypoints are used when the aircraft must fly over the point prior to starting a turn. NOTE− FIG 1−2−2 illustrates several differences between a fly−by and a fly−over waypoint. FIG 1−2−2 Fly−by and Fly−over Waypoints (a) Time and fuel savings; (b) Reduced dependence on radar vectoring, altitude, and speed assignments allowing a reduction in required ATC radio transmissions; and (c) More efficient use of airspace. In addition to information found in this manual, guidance for domestic RNAV DPs, STARs, and routes may also be found in AC 90−100, U.S. Terminal and En Route Area Navigation (RNAV) Operations. 2. RNAV Operations. RNAV procedures, such as DPs and STARs, demand strict pilot awareness and maintenance of the procedure centerline. Pilots should possess a working knowledge of their aircraft navigation system to ensure RNAV procedures are flown in an appropriate manner. In addition, pilots should have an understanding of the various waypoint and leg types used in RNAV procedures; these are discussed in more detail below. (a) Waypoints. A waypoint is a predetermined geographical position that is defined in terms of latitude/longitude coordinates. Waypoints may be a simple named point in space or associated with existing navaids, intersections, or fixes. A waypoint is most often used to indicate a change in direction, speed, or altitude along the desired path. RNAV procedures make use of both fly−over and fly−by waypoints. (1) Fly−by waypoints. Fly−by waypoints are used when an aircraft should begin a turn to the next course prior to reaching the waypoint separating 1−2−2 (b) RNAV Leg Types. A leg type describes the desired path proceeding, following, or between waypoints on an RNAV procedure. Leg types are identified by a two−letter code that describes the path (e.g., heading, course, track, etc.) and the termination point (e.g., the path terminates at an altitude, distance, fix, etc.). Leg types used for procedure design are included in the aircraft navigation database, but not normally provided on the procedure chart. The narrative depiction of the RNAV chart describes how a procedure is flown. The “path and terminator concept” defines that every leg of a procedure has a termination point and some kind of path into that termination point. Some of the available leg types are described below. (1) Track to Fix. A Track to Fix (TF) leg is intercepted and acquired as the flight track to the following waypoint. Track to a Fix legs are sometimes called point−to−point legs for this reason. Narrative: “direct ALPHA, then on course to BRAVO WP.” See FIG 1−2−3. Performance−Based Navigation (PBN) and Area Navigation (RNAV) 6/17/21 AIM (2) Direct to Fix. A Direct to Fix (DF) leg is a path described by an aircraft’s track from an initial area direct to the next waypoint. Narrative: “turn right direct BRAVO WP.” See FIG 1−2−4. FIG 1−2−5 Course to Fix Leg Type FIG 1−2−3 Track to Fix Leg Type (4) Radius to Fix. A Radius to Fix (RF) leg is defined as a constant radius circular path around a defined turn center that terminates at a fix. See FIG 1−2−6. FIG 1−2−6 Radius to Fix Leg Type FIG 1−2−4 Direct to Fix Leg Type (3) Course to Fix. A Course to Fix (CF) leg is a path that terminates at a fix with a specified course at that fix. Narrative: “on course 150 to ALPHA WP.” See FIG 1−2−5. (5) Heading. A Heading leg may be defined as, but not limited to, a Heading to Altitude (VA), Heading to DME range (VD), and Heading to Manual Termination, i.e., Vector (VM). Narrative: “climb heading 350 to 1500”, “heading 265, at 9 DME west of PXR VORTAC, right turn heading 360”, “fly heading 090, expect radar vectors to DRYHT INT.” Performance−Based Navigation (PBN) and Area Navigation (RNAV) 1−2−3 AIM 6/17/21 (c) Navigation Issues. Pilots should be aware of their navigation system inputs, alerts, and annunciations in order to make better−informed decisions. In addition, the availability and suitability of particular sensors/systems should be considered. (1) GPS/WAAS. Operators using TSO− C129(), TSO−C196(), TSO−C145() or TSO−C146() systems should ensure departure and arrival airports are entered to ensure proper RAIM availability and CDI sensitivity. (e) RNAV Navigation Specifications (Nav Specs) Nav Specs are a set of aircraft and aircrew requirements needed to support a navigation application within a defined airspace concept. For both RNP and RNAV designations, the numerical designation refers to the lateral navigation accuracy in nautical miles which is expected to be achieved at least 95 percent of the flight time by the population of aircraft operating within the airspace, route, or procedure. (See FIG 1−2−1.) (2) DME/DME. Operators should be aware that DME/DME position updating is dependent on navigation system logic and DME facility proximity, availability, geometry, and signal masking. (1) RNAV 1. Typically RNAV 1 is used for DPs and STARs and appears on the charts. Aircraft must maintain a total system error of not more than 1 NM for 95 percent of the total flight time. (3) VOR/DME. Unique VOR characteristics may result in less accurate values from VOR/DME position updating than from GPS or DME/DME position updating. (2) RNAV 2. Typically RNAV 2 is used for en route operations unless otherwise specified. T-routes and Q-routes are examples of this Nav Spec. Aircraft must maintain a total system error of not more than 2 NM for 95 percent of the total flight time. (4) Inertial Navigation. Inertial reference units and inertial navigation systems are often coupled with other types of navigation inputs, e.g., DME/DME or GPS, to improve overall navigation system performance. NOTE− Specific inertial position updating requirements may apply. (d) Flight Management System (FMS). An FMS is an integrated suite of sensors, receivers, and computers, coupled with a navigation database. These systems generally provide performance and RNAV guidance to displays and automatic flight control systems. Inputs can be accepted from multiple sources such as GPS, DME, VOR, LOC and IRU. These inputs may be applied to a navigation solution one at a time or in combination. Some FMSs provide for the detection and isolation of faulty navigation information. When appropriate navigation signals are available, FMSs will normally rely on GPS and/or DME/DME (that is, the use of distance information from two or more DME stations) for position updates. Other inputs may also be incorporated based on FMS system architecture and navigation source geometry. NOTE− DME/DME inputs coupled with one or more IRU(s) are often abbreviated as DME/DME/IRU or D/D/I. 1−2−4 (3) RNAV 10. Typically RNAV 10 is used in oceanic operations. See paragraph 4−7−1 for specifics and explanation of the relationship between RNP 10 and RNAV 10 terminology. 1−2−2. Required Navigation Performance (RNP) a. General. While both RNAV navigation specifications (NavSpecs) and RNP NavSpecs contain specific performance requirements, RNP is RNAV with the added requirement for onboard performance monitoring and alerting (OBPMA). RNP is also a statement of navigation performance necessary for operation within a defined airspace. A critical component of RNP is the ability of the aircraft navigation system to monitor its achieved navigation performance, and to identify for the pilot whether the operational requirement is, or is not, being met during an operation. OBPMA capability therefore allows a lessened reliance on air traffic control intervention and/or procedural separation to achieve the overall safety of the operation. RNP capability of the aircraft is a major component in determining the separation criteria to ensure that the overall containment of the operation is met. The RNP capability of an aircraft will vary depending upon the aircraft equipment and the navigation infrastructure. For example, an aircraft may be eligible for RNP 1, but may not be capable of RNP 1 operations due to limited NAVAID coverage Performance−Based Navigation (PBN) and Area Navigation (RNAV) 12/2/21 6/17/21 or avionics failure. The Aircraft Flight Manual (AFM) or avionics documents for your aircraft should specifically state the aircraft’s RNP eligibilities. Contact the manufacturer of the avionics or the aircraft if this information is missing or incomplete. NavSpecs should be considered different from one another, not “better” or “worse” based on the described lateral navigation accuracy. It is this concept that requires each NavSpec eligbility to be listed separately in the avionics documents or AFM. For example, RNP 1 is different from RNAV 1, and an RNP 1 eligibility does NOT mean automatic RNP 2 or RNAV 1 eligibility. As a safeguard, the FAA requires that aircraft navigation databases hold only those procedures that the aircraft maintains eligibility for. If you look for a specific instrument procedure in your aircraft’s navigation database and cannot find it, it’s likely that procedure contains PBN elements your aircraft is ineligible for or cannot compute and fly. Further, optional capabilities such as Radius−to−fix (RF) turns or scalability should be described in the AFM or avionics documents. Use the capabilities of your avionics suite to verify the appropriate waypoint and track data after loading the procedure from your database. b. PBN Operations. 1. Lateral Accuracy Values. Lateral Accuracy values are applicable to a selected airspace, route, or procedure. The lateral accuracy value is a value typically expressed as a distance in nautical miles from the intended centerline of a procedure, route, or path. RNP applications also account for potential errors at some multiple of lateral accuracy value (for example, twice the RNP lateral accuracy values). (a) RNP NavSpecs. U.S. standard NavSpecs supporting typical RNP airspace uses are as specified below. Other NavSpecs may include different lateral accuracy values as identified by ICAO or other states. (See FIG 1−2−1.) (1) RNP Approach (RNP APCH). In the U.S., RNP APCH procedures are titled RNAV (GPS) and offer several lines of minima to accommodate varying levels of aircraft equipage: either lateral navigation (LNAV), LNAV/vertical navigation (LNAV/VNAV), Localizer Performance with Vertical Guidance (LPV), and Localizer Performance (LP). GPS with or without Space−Based Augmentation System (SBAS) (for example, WAAS) can provide the lateral information to support LNAV AIM minima. LNAV/VNAV incorporates LNAV lateral with vertical path guidance for systems and operators capable of either barometric or SBAS vertical. Pilots are required to use SBAS to fly to the LPV or LP minima. RF turn capability is optional in RNP APCH eligibility. This means that your aircraft may be eligible for RNP APCH operations, but you may not fly an RF turn unless RF turns are also specifically listed as a feature of your avionics suite. GBAS Landing System (GLS) procedures are also constructed using RNP APCH NavSpecs and provide precision approach capability. RNP APCH has a lateral accuracy value of 1 in the terminal and missed approach segments and essentially scales to RNP 0.3 (or 40 meters with SBAS) in the final approach. (See paragraph 5−4−18, RNP AR (Authorization Required) Instrument Procedures.) (2) RNP Authorization Required Approach (RNP AR APCH). In the U.S., RNP AR APCH procedures are titled RNAV (RNP). These approaches have stringent equipage and pilot training standards and require special FAA authorization to fly. Scalability and RF turn capabilities are mandatory in RNP AR APCH eligibility. RNP AR APCH vertical navigation performance is based upon barometric VNAV or SBAS. RNP AR is intended to provide specific benefits at specific locations. It is not intended for every operator or aircraft. RNP AR capability requires specific aircraft performance, design, operational processes, training, and specific procedure design criteria to achieve the required target level of safety. RNP AR APCH has lateral accuracy values that can range below 1 in the terminal and missed approach segments and essentially scale to RNP 0.3 or lower in the final approach. Before conducting these procedures, operators should refer to the latest AC 90−101, Approval Guidance for RNP Procedures with AR. (See paragraph 5−4−18.) (3) RNP Authorization Required Departure (RNP AR DP). Similar to RNP AR approaches, RNP AR departure procedures have stringent equipage and pilot training standards and require special FAA authorization to fly. Scalability and RF turn capabilities is mandatory in RNP AR DP eligibility. RNP AR DP is intended to provide specific benefits at specific locations. It is not intended for every operator or aircraft. RNP AR DP capability requires specific aircraft performance, design, operational processes, training, and specific procedure design criteria to achieve the required Performance−Based Navigation (PBN) and Area Navigation (RNAV) 1−2−5 AIM 6/17/21 target level of safety. RNP AR DP has lateral accuracy values that can scale to no lower than RNP 0.3 in the initial departure flight path. Before conducting these procedures, operators should refer to the latest AC 90−101, Approval Guidance for RNP Procedures with AR. (See paragraph 5−4−18.) (4) Advanced RNP (A−RNP). Advanced RNP is a NavSpec with a minimum set of mandatory functions enabled in the aircraft’s avionics suite. In the U.S., these minimum functions include capability to calculate and perform RF turns, scalable RNP, and parallel offset flight path generation. Higher continuity (such as dual systems) may be required for certain oceanic and remote continental airspace. Other “advanced” options for use in the en route environment (such as fixed radius transitions and Time of Arrival Control) are optional in the U.S. Typically, an aircraft eligible for A−RNP will also be eligible for operations comprising: RNP APCH, RNP/RNAV 1, RNP/RNAV 2, RNP 4, and RNP/RNAV 10. A−RNP allows for scalable RNP lateral navigation values (either 1.0 or 0.3) in the terminal environment. Use of these reduced lateral accuracies will normally require use of the aircraft’s autopilot and/or flight director. See the latest AC 90−105 for more information on A−RNP, including NavSpec bundling options, eligibility determinations, and operations approvals. NOTE− A−RNP eligible aircraft are NOT automatically eligible for RNP AR APCH or RNP AR DP operations, as RNP AR eligibility requires a separate determination process and special FAA authorization. (5) RNP 1. RNP 1 requires a lateral accuracy value of 1 for arrival and departure in the terminal area, and the initial and intermediate approach phase when used on conventional procedures with PBN segments (for example, an ILS with a PBN feeder, IAF, or missed approach). RF turn capability is optional in RNP 1 eligibility. This means that your aircraft may be eligible for RNP 1 operations, but you may not fly an RF turn unless RF turns are also specifically listed as a feature of your avionics suite. (6) RNP 2. RNP 2 will apply to both domestic and oceanic/remote operations with a lateral accuracy value of 2. (7) RNP 4. RNP 4 will apply to oceanic and remote operations only with a lateral accuracy value 1−2−6 of 4. RNP 4 eligibility will automatically confer RNP 10 eligibility. (8) RNP 10. The RNP 10 NavSpec applies to certain oceanic and remote operations with a lateral accuracy of 10. In such airspace, the RNAV 10 NavSpec will be applied, so any aircraft eligible for RNP 10 will be deemed eligible for RNAV 10 operations. Further, any aircraft eligible for RNP 4 operations is automatically qualified for RNP 10/ RNAV 10 operations. (See also the latest AC 91−70, Oceanic and Remote Continental Airspace Operations, for more information on oceanic RNP/RNAV operations.) (9) RNP 0.3. The RNP 0.3 NavSpec requires a lateral accuracy value of 0.3 for all authorized phases of flight. RNP 0.3 is not authorized for oceanic, remote, or the final approach segment. Use of RNP 0.3 by slow−flying fixed−wing aircraft is under consideration, but the RNP 0.3 NavSpec initially will apply only to rotorcraft operations. RF turn capability is optional in RNP 0.3 eligibility. This means that your aircraft may be eligible for RNP 0.3 operations, but you may not fly an RF turn unless RF turns are also specifically listed as a feature of your avionics suite. NOTE− On terminal procedures or en route charts, do not confuse a charted RNP value of 0.30, or any standard final approach course segment width of 0.30, with the NavSpec title “RNP 0.3.” Charted RNP values of 0.30 or below should contain two decimal places (for example, RNP 0.15, or 0.10, or 0.30) whereas the NavSpec title will only state “RNP 0.3.” (b) Application of Standard Lateral Accuracy Values. U.S. standard lateral accuracy values typically used for various routes and procedures supporting RNAV operations may be based on use of a specific navigational system or sensor such as GPS, or on multi−sensor RNAV systems having suitable performance. (c) Depiction of PBN Requirements. In the U.S., PBN requirements like Lateral Accuracy Values or NavSpecs applicable to a procedure will be depicted on affected charts and procedures. In the U.S., a specific procedure’s Performance−Based Navigation (PBN) requirements will be prominently displayed in separate, standardized notes boxes. For procedures with PBN elements, the “PBN box” will contain the procedure’s NavSpec(s); and, if required: specific sensors or infrastructure needed for the Performance−Based Navigation (PBN) and Area Navigation (RNAV) 6/17/21 AIM navigation solution, any additional or advanced functional requirements, the minimum RNP value, and any amplifying remarks. Items listed in this PBN box are REQUIRED to fly the procedure’s PBN elements. For example, an ILS with an RNAV missed approach would require a specific capability to fly the missed approach portion of the procedure. That required capability will be listed in the PBN box. The separate Equipment Requirements box will list ground−based equipment and/or airport specific requirements. On procedures with both PBN elements and ground−based equipment requirements, the PBN requirements box will be listed first. (See FIG 5−4−1.) c. Other RNP Applications Outside the U.S. The FAA and ICAO member states have led initiatives in implementing the RNP concept to oceanic operations. For example, RNP−10 routes have been established in the northern Pacific (NOPAC) which has increased capacity and efficiency by reducing the distance between tracks to 50 NM. (See paragraph 4−7−1.) d. Aircraft and Airborne Equipment Eligibility for RNP Operations. Aircraft eligible for RNP operations will have an appropriate entry including special conditions and limitations in its AFM, avionics manual, or a supplement. Operators of aircraft not having specific RNP eligibility statements in the AFM or avionics documents may be issued operational approval including special conditions and limitations for specific RNP eligibilities. NOTE− Some airborne systems use Estimated Position Uncertainty (EPU) as a measure of the current estimated navigational performance. EPU may also be referred to as Actual Navigation Performance (ANP) or Estimated Position Error (EPE). TBL 1−2−1 U.S. Standard RNP Levels RNP Level Typical Application Primary Route Width (NM) − Centerline to Boundary 0.1 to 1.0 0.3 to 1.0 1 2 4 RNP AR Approach Segments RNP Approach Segments Terminal and En Route En Route Projected for oceanic/remote areas where 30 NM horizontal separation is applied. Oceanic/remote areas where 50 NM lateral separation is applied. 0.1 to 1.0 0.3 to 1.0 1.0 2.0 4.0 10 1−2−3. Use of Suitable Area Navigation (RNAV) Systems on Conventional Procedures and Routes a. Discussion. This paragraph sets forth policy, while providing operational and airworthiness guidance regarding the suitability and use of RNAV systems when operating on, or transitioning to, conventional, non−RNAV routes and procedures within the U.S. National Airspace System (NAS): 1. Use of a suitable RNAV system as a Substitute Means of Navigation when a Very−High Frequency (VHF) Omni−directional Range (VOR), 10.0 Distance Measuring Equipment (DME), Tactical Air Navigation (TACAN), VOR/TACAN (VORTAC), VOR/DME, Non−directional Beacon (NDB), or compass locator facility including locator outer marker and locator middle marker is out−of−service (that is, the navigation aid (NAVAID) information is not available); an aircraft is not equipped with an Automatic Direction Finder (ADF) or DME; or the installed ADF or DME on an aircraft is not operational. For example, if equipped with a suitable RNAV system, a pilot may hold over an out−of−service NDB. Performance−Based Navigation (PBN) and Area Navigation (RNAV) 1−2−7 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 2. Use of a suitable RNAV system as an Alternate Means of Navigation when a VOR, DME, VORTAC, VOR/DME, TACAN, NDB, or compass locator facility including locator outer marker and locator middle marker is operational and the respective aircraft is equipped with operational navigation equipment that is compatible with conventional navaids. For example, if equipped with a suitable RNAV system, a pilot may fly a procedure or route based on operational VOR using that RNAV system without monitoring the VOR. NOTE− 1. Additional information and associated requirements are available in Advisory Circular 90-108 titled “Use of Suitable RNAV Systems on Conventional Routes and Procedures.” 2. Good planning and knowledge of your RNAV system are critical for safe and successful operations. 3. Pilots planning to use their RNAV system as a substitute means of navigation guidance in lieu of an out−of−service NAVAID may need to advise ATC of this intent and capability. 4. The navigation database should be current for the duration of the flight. If the AIRAC cycle will change during flight, operators and pilots should establish procedures to ensure the accuracy of navigation data, including suitability of navigation facilities used to define the routes and procedures for flight. To facilitate validating database currency, the FAA has developed procedures for publishing the amendment date that instrument approach procedures were last revised. The amendment date follows the amendment number, e.g., Amdt 4 14Jan10. Currency of graphic departure procedures and STARs may be ascertained by the numerical designation in the procedure title. If an amended chart is published for the procedure, or the procedure amendment date shown on the chart is on or after the expiration date of the database, the operator must not use the database to conduct the operation. b. Types of RNAV Systems that Qualify as a Suitable RNAV System. When installed in accordance with appropriate airworthiness installation requirements and operated in accordance with applicable operational guidance (for example, aircraft flight manual and Advisory Circular material), the following systems qualify as a suitable RNAV system: 1. An RNAV system with TSO−C129/ −C145/−C146 equipment, installed in accordance with AC 20−138, Airworthiness Approval of Global Positioning System (GPS) Navigation Equipment for 1−2−8 Use as a VFR and IFR Supplemental Navigation System, and authorized for instrument flight rules (IFR) en route and terminal operations (including those systems previously qualified for “GPS in lieu of ADF or DME” operations), or 2. An RNAV system with DME/DME/IRU inputs that is compliant with the equipment provisions of AC 90−100A, U.S. Terminal and En Route Area Navigation (RNAV) Operations, for RNAV routes. A table of compliant equipment is available at the following website: https://www.faa.gov/about/office_org/headquarters _offices/avs/offices/afx/afs/afs400/afs410/media/ AC90−100compliance.pdf NOTE− Approved RNAV systems using DME/DME/IRU, without GPS/WAAS position input, may only be used as a substitute means of navigation when specifically authorized by a Notice to Air Missions (NOTAM) or other FAA guidance for a specific procedure. The NOTAM or other FAA guidance authorizing the use of DME/DME/IRU systems will also identify any required DME facilities based on an FAA assessment of the DME navigation infrastructure. c. Uses of Suitable RNAV Systems. Subject to the operating requirements, operators may use a suitable RNAV system in the following ways. 1. Determine aircraft position relative to, or distance from a VOR (see NOTE 6 below), TACAN, NDB, compass locator, DME fix; or a named fix defined by a VOR radial, TACAN course, NDB bearing, or compass locator bearing intersecting a VOR or localizer course. 2. Navigate to or from a VOR, TACAN, NDB, or compass locator. 3. Hold over a VOR, TACAN, NDB, compass locator, or DME fix. 4. Fly an arc based upon DME. NOTE− 1. The allowances described in this section apply even when a facility is identified as required on a procedure (for example, “Note ADF required”). 2. These operations do not include lateral navigation on localizer−based courses (including localizer back−course guidance) without reference to raw localizer data. 3. Unless otherwise specified, a suitable RNAV system cannot be used for navigation on procedures that are identified as not authorized (“NA”) without exception by a NOTAM. For example, an operator may not use a RNAV system to navigate on a procedure affected by an expired or Performance−Based Navigation (PBN) and Area Navigation (RNAV) 6/17/21 AIM unsatisfactory flight inspection, or a procedure that is based upon a recently decommissioned NAVAID. alternate airport, pilots may plan for applicable alternate airport weather minimums using: 4. Pilots may not substitute for the NAVAID (for example, a VOR or NDB) providing lateral guidance for the final approach segment. This restriction does not refer to instrument approach procedures with “or GPS” in the title when using GPS or WAAS. These allowances do not apply to procedures that are identified as not authorized (NA) without exception by a NOTAM, as other conditions may still exist and result in a procedure not being available. For example, these allowances do not apply to a procedure associated with an expired or unsatisfactory flight inspection, or is based upon a recently decommissioned NAVAID. (a) Lateral navigation (LNAV) or circling minimum descent altitude (MDA); 5. Use of a suitable RNAV system as a means to navigate on the final approach segment of an instrument approach procedure based on a VOR, TACAN or NDB signal, is allowable. The underlying NAVAID must be operational and the NAVAID monitored for final segment course alignment. 2. If the above conditions cannot be met, any required alternate airport must have an approved instrument approach procedure other than GPS that is anticipated to be operational and available at the estimated time of arrival, and which the aircraft is equipped to fly. 6. For the purpose of paragraph c, “VOR” includes VOR, VOR/DME, and VORTAC facilities and “compass locator” includes locator outer marker and locator middle marker. d. Alternate Airport Considerations. For the purposes of flight planning, any required alternate airport must have an available instrument approach procedure that does not require the use of GPS. This restriction includes conducting a conventional approach at the alternate airport using a substitute means of navigation that is based upon the use of GPS. For example, these restrictions would apply when planning to use GPS equipment as a substitute means of navigation for an out−of−service VOR that supports an ILS missed approach procedure at an alternate airport. In this case, some other approach not reliant upon the use of GPS must be available. This restriction does not apply to RNAV systems using TSO−C145/−C146 WAAS equipment. For further WAAS guidance, see paragraph 1−1−18. 1. For flight planning purposes, TSO-C129() and TSO-C196() equipped users (GPS users) whose navigation systems have fault detection and exclusion (FDE) capability, who perform a preflight RAIM prediction at the airport where the RNAV (GPS) approach will be flown, and have proper knowledge and any required training and/or approval to conduct a GPS-based IAP, may file based on a GPS-based IAP at either the destination or the alternate airport, but not at both locations. At the (b) LNAV/vertical navigation (LNAV/ VNAV) DA, if equipped with and using approved barometric vertical navigation (baro-VNAV) equipment; (c) RNP 0.3 DA on an RNAV (RNP) IAP, if they are specifically authorized users using approved baro-VNAV equipment and the pilot has verified required navigation performance (RNP) availability through an approved prediction program. 3. This restriction does not apply to TSO-C145() and TSO-C146() equipped users (WAAS users). For further WAAS guidance, see paragraph 1−1−18. 1−2−4. Recognizing, Mitigating and Adapting to GPS Interference (Jamming or Spoofing) a. The low−strength data transmission signals from GPS satellites are vulnerable to various anomalies that can significantly reduce the reliability of the navigation signal. Because of the many uses of GPS in aviation (e.g., navigation, ADS−B, terrain awareness/warning systems), operators of aircraft using GPS need to be aware of these vulnerabilities, and be able to recognize and adjust to degraded signals. Aircraft should have additional navigation equipment for their intended route. b. GPS signals are vulnerable to intentional and unintentional interference from a wide variety of sources, including radars, microwave links, ionosphere effects, solar activity, multi−path error, satellite communications, GPS repeaters, and even some systems onboard the aircraft. In general, these types of unintentional interference are localized and intermittent. Of greater and growing concern is the intentional and unauthorized interference of GPS signals by persons using “jammers” or “spoofers” to disrupt air navigation by interfering with the reception of valid satellite signals. Performance−Based Navigation (PBN) and Area Navigation (RNAV) 1−2−9 AIM 6/17/21 NOTE− The U.S. government regularly conducts GPS tests, training activities, and exercises that interfere with GPS signals. These events are geographically limited, coordinated, scheduled, and advertised via GPS and/or WAAS NOTAMS. Operators of GPS aircraft should always check for GPS and/or WAAS NOTAMS for their route of flight. c. GPS is a critical component of essential communication, navigation, and surveillance (CNS) in the NAS; and flight safety/control systems. Additionally, some satellite communications avionics use GPS signals for operations in oceanic and remote airspaces. It is the sole aircraft position−reporting source for Automatic Dependent Surveillance – Broadcast (ADS−B). Some business aircraft are using GPS as a reference source for aircraft flight control and stability systems. GPS is also a necessary component of the Aircraft Terrain Awareness and Warning System (TAWS) – an aircraft safety system that alerts pilots of upcoming terrain. There are examples of false “terrain−pull up” warnings during GPS anomalies. d. When flying IFR, pilots should have additional navigation equipment for their intended route to crosscheck their position. Routine checks of position against VOR or DME information, for example, 1−2−10 could help detect a compromised GPS signal. Pilots transitioning to VOR navigation in response to GPS anomalies should refer to the Chart Supplement U.S. to identify airports with available conventional approaches associated with the VOR Minimum Operational Network (MON) program. (Reference 1−1−3f.) e. When flying GPS approaches, particularly in IMC, pilots should have a backup plan in the event of GPS anomalies. Although the appropriate response will vary with the situation, in general pilots should: 1. Maintain control of the aircraft, 2. Use the last reliable navigation information as the basis for initial headings, and climb above terrain, 3. Change to another source of navigation, if available (i.e., VOR, DME radar vectors). 4. Contact ATC as soon as practical. f. Pilots should promptly notify ATC if they experience GPS anomalies. Pilots should not normally inform ATC of GPS interference or outages when flying through a known NOTAMed testing area, unless they require ATC assistance. (See 1−1−13.) Performance−Based Navigation (PBN) and Area Navigation (RNAV) 12/2/21 6/17/21 AIM Chapter 2. Aeronautical Lighting and Other Airport Visual Aids Section 1. Airport Lighting Aids 2−1−1. Approach Light Systems (ALS) a. ALS provide the basic means to transition from instrument flight to visual flight for landing. Operational requirements dictate the sophistication and configuration of the approach light system for a particular runway. b. ALS are a configuration of signal lights starting at the landing threshold and extending into the approach area a distance of 2400−3000 feet for precision instrument runways and 1400−1500 feet for nonprecision instrument runways. Some systems include sequenced flashing lights which appear to the pilot as a ball of light traveling towards the runway at high speed (twice a second). (See FIG 2−1−1.) 2−1−2. Visual Glideslope Indicators a. Visual Approach Slope Indicator (VASI) 1. VASI installations may consist of either 2, 4, 6, 12, or 16 light units arranged in bars referred to as near, middle, and far bars. Most VASI installations consist of 2 bars, near and far, and may consist of 2, 4, or 12 light units. Some VASIs consist of three bars, near, middle, and far, which provide an additional visual glide path to accommodate high cockpit aircraft. This installation may consist of either 6 or 16 light units. VASI installations consisting of 2, 4, or 6 light units are located on one side of the runway, usually the left. Where the installation consists of 12 or 16 light units, the units are located on both sides of the runway. 2. Two−bar VASI installations provide one visual glide path which is normally set at 3 degrees. Three−bar VASI installations provide two visual glide paths. The lower glide path is provided by the near and middle bars and is normally set at 3 degrees Airport Lighting Aids while the upper glide path, provided by the middle and far bars, is normally 1/4 degree higher. This higher glide path is intended for use only by high cockpit aircraft to provide a sufficient threshold crossing height. Although normal glide path angles are three degrees, angles at some locations may be as high as 4.5 degrees to give proper obstacle clearance. Pilots of high performance aircraft are cautioned that use of VASI angles in excess of 3.5 degrees may cause an increase in runway length required for landing and rollout. 3. The basic principle of the VASI is that of color differentiation between red and white. Each light unit projects a beam of light having a white segment in the upper part of the beam and red segment in the lower part of the beam. The light units are arranged so that the pilot using the VASIs during an approach will see the combination of lights shown below. 4. The VASI is a system of lights so arranged to provide visual descent guidance information during the approach to a runway. These lights are visible from 3−5 miles during the day and up to 20 miles or more at night. The visual glide path of the VASI provides safe obstruction clearance within plus or minus 10 degrees of the extended runway centerline and to 4 NM from the runway threshold. Descent, using the VASI, should not be initiated until the aircraft is visually aligned with the runway. Lateral course guidance is provided by the runway or runway lights. In certain circumstances, the safe obstruction clearance area may be reduced by narrowing the beam width or shortening the usable distance due to local limitations, or the VASI may be offset from the extended runway centerline. This will be noted in the Chart Supplement U.S. and/or applicable Notices to Air Missions (NOTAMs). 2−1−1 AIM 6/17/21 FIG 2−1−1 Precision & Nonprecision Configurations NOTE− Civil ALSF−2 may be operated as SSALR during favorable weather conditions. 2−1−2 Airport Lighting Aids 6/17/21 AIM 5. For 2−bar VASI (4 light units) see FIG 2−1−2. FIG 2−1−2 2−Bar VASI Far Bar = Red Near Bar = White Below Glide Path On Glide Path Above Glide Path 6. For 3−bar VASI (6 light units) see FIG 2−1−3. FIG 2−1−3 3−Bar VASI Far Bar Middle Bar Near Bar Below Both Glide Paths On Lower Glide Path On Upper Glide Path Above Both Glide Paths 7. For other VASI configurations see FIG 2−1−4. FIG 2−1−4 VASI Variations 2 Bar 2 Light Units On Glide Path Airport Lighting Aids 2 Bar 12 Light Units On Glide Path 3 Bar 16 Light Units on Lower Glide Path 2−1−3 AIM 6/17/21 b. Precision Approach Path Indicator (PAPI). The precision approach path indicator (PAPI) uses light units similar to the VASI but are installed in a single row of either two or four light units. These lights are visible from about 5 miles during the day and up to 20 miles at night. The visual glide path of the PAPI typically provides safe obstruction clearance within plus or minus 10 degrees of the extended runway centerline and to 3.4 NM from the runway threshold. Descent, using the PAPI, should not be initiated until the aircraft is visually aligned with the runway. The row of light units is normally installed on the left side of the runway and the glide path indications are as depicted. Lateral course guidance is provided by the runway or runway lights. In certain circumstances, the safe obstruction clearance area may be reduced by narrowing the beam width or shortening the usable distance due to local limitations, or the PAPI may be offset from the extended runway centerline. This will be noted in the Chart Supplement U.S. and/or applicable NOTAMs. (See FIG 2−1−5.) FIG 2−1−5 Precision Approach Path Indicator (PAPI) High (More Than 3,5 Degrees) Slightly High (3.2 Degrees) On Glide Path (3 Degrees) Slightly Low (2.8 Degrees) Low (Less Than 2.5 Degrees) White Red c. Tri−color Systems. Tri−color visual approach slope indicators normally consist of a single light unit projecting a three−color visual approach path into the final approach area of the runway upon which the indicator is installed. The below glide path indication is red, the above glide path indication is amber, and the on glide path indication is green. These types of indicators have a useful range of approximately one−half to one mile during the day and up to five miles at night depending upon the visibility conditions. (See FIG 2−1−6.) FIG 2−1−6 Tri−Color Visual Approach Slope Indicator Amber th Pa de Gli th e e Pa ov Ab On Glid ath lide P G w Belo Green Red Amber NOTE− 1. Since the tri−color VASI consists of a single light source which could possibly be confused with other light sources, pilots should exercise care to properly locate and identify the light signal. 2−1−4 Airport Lighting Aids 6/17/21 AIM 2. When the aircraft descends from green to red, the pilot may see a dark amber color during the transition from green to red. FIG 2−1−7 Pulsating Visual Approach Slope Indicator NOTE− Since the PVASI consists of a single light source which could possibly be confused with other light sources, pilots should exercise care to properly locate and identify the light signal. FIG 2−1−8 Alignment of Elements Above Glide Path d. Pulsating Systems. Pulsating visual approach slope indicators normally consist of a single light unit projecting a two−color visual approach path into the final approach area of the runway upon which the indicator is installed. The on glide path indication may be a steady white light or alternating RED and WHITE light. The slightly below glide path indication is a steady red light. If the aircraft descends further below the glide path, the red light starts to pulsate. The above glide path indication is a pulsating white light. The pulsating rate increases as the aircraft Airport Lighting Aids On Glide Path Below Glide Path gets further above or below the desired glide slope. The useful range of the system is about four miles during the day and up to ten miles at night. (See FIG 2−1−7.) e. Alignment of Elements Systems. Alignment of elements systems are installed on some small general aviation airports and are a low−cost system consisting of painted plywood panels, normally black and white or fluorescent orange. Some of these systems are lighted for night use. The useful range of 2−1−5 AIM these systems is approximately three−quarter miles. To use the system the pilot positions the aircraft so the elements are in alignment. The glide path indications are shown in FIG 2−1−8. 2−1−3. Runway End Identifier Lights (REIL) REILs are installed at many airfields to provide rapid and positive identification of the approach end of a particular runway. The system consists of a pair of synchronized flashing lights located laterally on each side of the runway threshold. REILs may be either omnidirectional or unidirectional facing the approach area. They are effective for: a. Identification of a runway surrounded by a preponderance of other lighting. b. Identification of a runway which lacks contrast with surrounding terrain. c. Identification of a runway during reduced visibility. 2−1−4. Runway Edge Light Systems a. Runway edge lights are used to outline the edges of runways during periods of darkness or restricted visibility conditions. These light systems are classified according to the intensity or brightness they are capable of producing: they are the High Intensity Runway Lights (HIRL), Medium Intensity Runway Lights (MIRL), and the Low Intensity Runway Lights (LIRL). The HIRL and MIRL systems have variable intensity controls, whereas the LIRLs normally have one intensity setting. b. The runway edge lights are white, except on instrument runways yellow replaces white on the last 2,000 feet or half the runway length, whichever is less, to form a caution zone for landings. c. The lights marking the ends of the runway emit red light toward the runway to indicate the end of runway to a departing aircraft and emit green outward from the runway end to indicate the threshold to landing aircraft. 2−1−5. In−runway Lighting a. Runway Centerline Lighting System (RCLS). Runway centerline lights are installed on some precision approach runways to facilitate landing under adverse visibility conditions. They are located along the runway centerline and are spaced at 50−foot intervals. When viewed from the landing 2−1−6 6/17/21 threshold, the runway centerline lights are white until the last 3,000 feet of the runway. The white lights begin to alternate with red for the next 2,000 feet, and for the last 1,000 feet of the runway, all centerline lights are red. b. Touchdown Zone Lights (TDZL). Touchdown zone lights are installed on some precision approach runways to indicate the touchdown zone when landing under adverse visibility conditions. They consist of two rows of transverse light bars disposed symmetrically about the runway centerline. The system consists of steady−burning white lights which start 100 feet beyond the landing threshold and extend to 3,000 feet beyond the landing threshold or to the midpoint of the runway, whichever is less. c. Taxiway Centerline Lead−Off Lights. Taxiway centerline lead−off lights provide visual guidance to persons exiting the runway. They are color−coded to warn pilots and vehicle drivers that they are within the runway environment or instrument landing system (ILS) critical area, whichever is more restrictive. Alternate green and yellow lights are installed, beginning with green, from the runway centerline to one centerline light position beyond the runway holding position or ILS critical area holding position. d. Taxiway Centerline Lead−On Lights. Taxiway centerline lead−on lights provide visual guidance to persons entering the runway. These “lead−on” lights are also color−coded with the same color pattern as lead−off lights to warn pilots and vehicle drivers that they are within the runway environment or instrument landing system (ILS) critical area, whichever is more conservative. The fixtures used for lead−on lights are bidirectional, i.e., one side emits light for the lead−on function while the other side emits light for the lead−off function. Any fixture that emits yellow light for the lead−off function must also emit yellow light for the lead−on function. (See FIG 2−1−12.) e. Land and Hold Short Lights. Land and hold short lights are used to indicate the hold short point on certain runways which are approved for Land and Hold Short Operations (LAHSO). Land and hold short lights consist of a row of pulsing white lights installed across the runway at the hold short point. Where installed, the lights will be on anytime LAHSO is in effect. These lights will be off when LAHSO is not in effect. Airport Lighting Aids 6/17/21 REFERENCE− AIM, Paragraph 4−3−11 , Pilot Responsibilities When Conducting Land and Hold Short Operations (LAHSO) 2−1−6. Runway Status Light (RWSL) System a. Introduction. RWSL is a fully automated system that provides runway status information to pilots and surface vehicle operators to clearly indicate when it is unsafe to enter, cross, takeoff from, or land on a runway. The RWSL system processes information from surveillance systems and activates Runway Entrance Lights (REL) and Takeoff Hold Lights (THL), in accordance with the position and velocity of the detected surface traffic and approach traffic. REL and THL are in−pavement light fixtures that are directly visible to pilots and surface vehicle operators. RWSL is an independent safety enhancement that does not substitute for or convey an ATC clearance. Clearance to enter, cross, takeoff from, land on, or operate on a runway must still be received from ATC. Although ATC has limited control over the system, personnel do not directly use and may not be able to view light fixture activations and deactivations during the conduct of daily ATC operations. b. Runway Entrance Lights (REL): The REL system is composed of flush mounted, in-pavement, unidirectional light fixtures that are parallel to and focused along the taxiway centerline and directed toward the pilot at the hold line. An array of REL lights include the first light at the hold line followed by a series of evenly spaced lights to the runway edge; one additional light at the runway centerline is in line with the last two lights before the runway edge (see FIG 2−1−9 and FIG 2−1−10). When activated, the red lights indicate that there is high speed traffic on the runway or there is an aircraft on final approach within the activation area. 1. REL Operating Characteristics − Departing Aircraft: When a departing aircraft reaches a site adaptable speed of approximately 30 knots, all taxiway intersections with REL arrays along the runway ahead of the aircraft will illuminate (see FIG 2−1−9). Airport Lighting Aids AIM As the aircraft approaches an REL equipped taxiway intersection, the lights at that intersection extinguish approximately 3 to 4 seconds before the aircraft reaches it. This allows controllers to apply “anticipated separation” to permit ATC to move traffic more expeditiously without compromising safety. After the aircraft is declared “airborne” by the system, all REL lights associated with this runway will extinguish. 2. REL Operating Characteristics − Arriving Aircraft: When an aircraft on final approach is approximately 1 mile from the runway threshold, all sets of taxiway REL light arrays that intersect the runway illuminate. The distance is adjustable and can be configured for specific operations at particular airports. Lights extinguish at each equipped taxiway intersection approximately 3 to 4 seconds before the aircraft reaches it to apply anticipated separation until the aircraft has slowed to approximately 80 knots (site adjustable parameter). Below 80 knots, all arrays that are not within 30 seconds of the aircraft’s forward path are extinguished. Once the arriving aircraft slows to approximately 34 knots (site adjustable parameter), it is declared to be in a taxi state, and all lights extinguish. 3. What a pilot would observe: A pilot at or approaching the hold line to a runway will observe RELs illuminate and extinguish in reaction to an aircraft or vehicle operating on the runway, or an arriving aircraft operating less than 1 mile from the runway threshold. 4. When a pilot observes the red lights of the REL, that pilot will stop at the hold line or remain stopped. The pilot will then contact ATC for resolution if the clearance is in conflict with the lights. Should pilots note illuminated lights under circumstances when remaining clear of the runway is impractical for safety reasons (for example, aircraft is already on the runway), the crew should proceed according to their best judgment while understanding the illuminated lights indicate the runway is unsafe to enter or cross. Contact ATC at the earliest possible opportunity. 2−1−7 AIM 6/17/21 FIG 2−1−9 Runway Status Light System c. Takeoff Hold Lights (THL) : The THL system is composed of flush mounted, in-pavement, unidirectional light fixtures in a double longitudinal row aligned either side of the runway centerline lighting. Fixtures are focused toward the arrival end of the runway at the “line up and wait” point. THLs extend for 1,500 feet in front of the holding aircraft starting at a point 375 feet from the departure threshold (see FIG 2−1−11). Illuminated red lights provide a signal, to an aircraft in position for takeoff or rolling, that it is unsafe to takeoff because the runway is occupied or about to be occupied by another aircraft or ground vehicle. Two aircraft, or a surface vehicle and an aircraft, are required for the lights to illuminate. The departing aircraft must be in position for takeoff or beginning takeoff roll. Another aircraft or a surface vehicle must be on or about to cross the runway. 1. THL Operating Characteristics − Departing Aircraft: THLs will illuminate for an aircraft in position for departure or departing when there is another aircraft or vehicle on the runway or about to enter the runway 2−1−8 (see FIG 2−1−9.) Once that aircraft or vehicle exits the runway, the THLs extinguish. A pilot may notice lights extinguish prior to the downfield aircraft or vehicle being completely clear of the runway but still moving. Like RELs, THLs have an “anticipated separation” feature. NOTE− When the THLs extinguish, this is not clearance to begin a takeoff roll. All takeoff clearances will be issued by ATC. 2. What a pilot would observe: A pilot in position to depart from a runway, or has begun takeoff roll, will observe THLs illuminate in reaction to an aircraft or vehicle on the runway or entering or crossing it. Lights will extinguish when the runway is clear. A pilot may observe several cycles of illumination and extinguishing depending on the amount of crossing traffic. 3. When a pilot observes the red light of the THLs, the pilot should safely stop if it’s feasible or remain stopped. The pilot must contact ATC for resolution if any clearance is in conflict with the lights. Should pilots note illuminated lights while in takeoff roll and under circumstances when stopping Airport Lighting Aids 6/17/21 is impractical for safety reasons, the crew should proceed according to their best judgment while understanding the illuminated lights indicate that continuing the takeoff is unsafe. Contact ATC at the earliest possible opportunity. d. Pilot Actions: 1. When operating at airports with RWSL, pilots will operate with the transponder/ADS−B “On” when departing the gate or parking area until it is shut down upon arrival at the gate or parking area. This ensures interaction with the FAA surveillance systems such as ASDE-X/Airport Surface Surveillance Capability (ASSC) which provide information to the RWSL system. 2. Pilots must always inform the ATCT when they have stopped due to an RWSL indication that is in conflict with ATC instructions. Pilots must request clarification of the taxi or takeoff clearance. 3. Never cross over illuminated red lights. Under normal circumstances, RWSL will confirm the pilot’s taxi or takeoff clearance previously issued by ATC. If RWSL indicates that it is unsafe to takeoff from, land on, cross, or enter a runway, immediately notify ATC of the conflict and re-confirm the clearance. 4. Do not proceed when lights have extinguished without an ATC clearance. RWSL verifies an ATC clearance; it does not substitute for an ATC clearance. 5. Never land if PAPI continues to flash. Execute a go around and notify ATC. e. ATC Control of RWSL System: 1. Controllers can set in−pavement lights to one of five (5) brightness levels to assure maximum conspicuity under all visibility and lighting condi- Airport Lighting Aids AIM tions. REL and THL subsystems may be independently set. 2. System lights can be disabled should RWSL operations impact the efficient movement of air traffic or contribute, in the opinion of the assigned ATC Manager, to unsafe operations. REL and THL light fixtures may be disabled separately. Whenever the system or a component is disabled, a NOTAM must be issued, and the Automatic Terminal Information System (ATIS) must be updated. 2−1−7. Control of Lighting Systems a. Operation of approach light systems and runway lighting is controlled by the control tower (ATCT). At some locations the FSS may control the lights where there is no control tower in operation. b. Pilots may request that lights be turned on or off. Runway edge lights, in−pavement lights and approach lights also have intensity controls which may be varied to meet the pilots request. Sequenced flashing lights (SFL) may be turned on and off. Some sequenced flashing light systems also have intensity control. 2−1−8. Pilot Control of Airport Lighting Radio control of lighting is available at selected airports to provide airborne control of lights by keying the aircraft’s microphone. Control of lighting systems is often available at locations without specified hours for lighting and where there is no control tower or FSS or when the tower or FSS is closed (locations with a part−time tower or FSS) or specified hours. All lighting systems which are radio controlled at an airport, whether on a single runway or multiple runways, operate on the same radio frequency. (See TBL 2−1−1 and TBL 2−1−2.) 2−1−9 AIM 6/17/21 FIG 2−1−10 Runway Entrance Lights FIG 2−1−11 Takeoff Hold Lights 2−1−10 Airport Lighting Aids 6/17/21 AIM FIG 2−1−12 Taxiway Lead−On Light Configuration TBL 2−1−1 Runways With Approach Lights Lighting System Approach Lights (Med. Int.) Approach Lights (Med. Int.) MIRL HIRL VASI No. of Int. Steps 2 3 3 5 2 Status During Nonuse Period Off Off Off or Low Off or Low Off Intensity Step Selected Per No. of Mike Clicks 3 Clicks 5 Clicks 7 Clicks Low Low Low Med High High NOTES: Predetermined intensity step. Low intensity for night use. High intensity for day use as determined by photocell control. TBL 2−1−2 Runways Without Approach Lights Lighting System MIRL HIRL LIRL VASI REIL REIL No. of Int. Steps 3 5 1 2 1 3 Status During Nonuse Period Off or Low Off or Low Off Off Off Off Intensity Step Selected Per No. of Mike Clicks 3 Clicks 5 Clicks 7 Clicks Low Step 1 or 2 On Med. Step 3 On High Step 5 On Off Low On/Off Med. On High NOTES: Low intensity for night use. High intensity for day use as determined by photocell control. The control of VASI and/or REIL may be independent of other lighting systems. Airport Lighting Aids 2−1−11 AIM a. With FAA approved systems, various combinations of medium intensity approach lights, runway lights, taxiway lights, VASI and/or REIL may be activated by radio control. On runways with both approach lighting and runway lighting (runway edge lights, taxiway lights, etc.) systems, the approach lighting system takes precedence for air−to−ground radio control over the runway lighting system which is set at a predetermined intensity step, based on expected visibility conditions. Runways without approach lighting may provide radio controlled intensity adjustments of runway edge lights. Other lighting systems, including VASI, REIL, and taxiway lights may be either controlled with the runway edge lights or controlled independently of the runway edge lights. b. The control system consists of a 3−step control responsive to 7, 5, and/or 3 microphone clicks. This 3−step control will turn on lighting facilities capable of either 3−step, 2−step or 1−step operation. The 3−step and 2−step lighting facilities can be altered in intensity, while the 1−step cannot. All lighting is illuminated for a period of 15 minutes from the most recent time of activation and may not be extinguished prior to end of the 15 minute period (except for 1−step and 2−step REILs which may be turned off when desired by keying the mike 5 or 3 times respectively). c. Suggested use is to always initially key the mike 7 times; this assures that all controlled lights are turned on to the maximum available intensity. If desired, adjustment can then be made, where the capability is provided, to a lower intensity (or the REIL turned off) by keying 5 and/or 3 times. Due to the close proximity of airports using the same frequency, radio controlled lighting receivers may be set at a low sensitivity requiring the aircraft to be relatively close to activate the system. Consequently, even when lights are on, always key mike as directed when overflying an airport of intended landing or just prior to entering the final segment of an approach. This will assure the aircraft is close enough to activate the system and a full 15 minutes lighting duration is available. Approved lighting systems may be activated by keying the mike (within 5 seconds) as indicated in TBL 2−1−3. 2−1−12 6/17/21 TBL 2−1−3 Radio Control System Key Mike Function 7 times within 5 seconds 5 times within 5 seconds Highest intensity available Medium or lower intensity (Lower REIL or REIL−off) 3 times within 5 seconds Lowest intensity available (Lower REIL or REIL−off) d. For all public use airports with FAA standard systems the Chart Supplement U.S. contains the types of lighting, runway and the frequency that is used to activate the system. Airports with IAPs include data on the approach chart identifying the light system, the runway on which they are installed, and the frequency that is used to activate the system. NOTE− Although the CTAF is used to activate the lights at many airports, other frequencies may also be used. The appropriate frequency for activating the lights on the airport is provided in the Chart Supplement U.S. and the standard instrument approach procedures publications. It is not identified on the sectional charts. e. Where the airport is not served by an IAP, it may have either the standard FAA approved control system or an independent type system of different specification installed by the airport sponsor. The Chart Supplement U.S. contains descriptions of pilot controlled lighting systems for each airport having other than FAA approved systems, and explains the type lights, method of control, and operating frequency in clear text. 2−1−9. Airport/Heliport Beacons a. Airport and heliport beacons have a vertical light distribution to make them most effective from one to ten degrees above the horizon; however, they can be seen well above and below this peak spread. The beacon may be an omnidirectional capacitor−discharge device, or it may rotate at a constant speed which produces the visual effect of flashes at regular intervals. Flashes may be one or two colors alternately. The total number of flashes are: 1. 24 to 30 per minute for beacons marking airports, landmarks, and points on Federal airways. 2. 30 to 45 per minute for beacons marking heliports. Airport Lighting Aids 6/17/21 b. The colors and color combinations of beacons are: 1. White and Green− Lighted land airport. 2. *Green alone− Lighted land airport. 3. White and Yellow− Lighted water airport. 4. *Yellow alone− Lighted water airport. 5. Green, Yellow, and White− Lighted heliport. NOTE− *Green alone or yellow alone is used only in connection with a white−and−green or white−and−yellow beacon display, respectively. c. Military airport beacons flash alternately white and green, but are differentiated from civil beacons by dualpeaked (two quick) white flashes between the green flashes. d. In Class B, Class C, Class D and Class E surface areas, operation of the airport beacon during the hours of daylight often indicates that the ground visibility is less than 3 miles and/or the ceiling is less than 1,000 feet. ATC clearance in accordance with 14 CFR Part 91 is required for landing, takeoff and flight in the traffic pattern. Pilots should not rely solely on the operation of the airport beacon to indicate if weather conditions are IFR or VFR. At some locations with operating control towers, ATC personnel turn the beacon on or off when controls are in the tower. At many airports the airport beacon is turned on by a photoelectric cell or time clocks and ATC personnel cannot control them. There is no regulatory requirement for daylight operation and it is the pilot’s responsibility to comply with proper preflight planning as required by 14 CFR Section 91.103. AIM portions, on the centerline of curved portions, and along designated taxiing paths in portions of runways, ramp, and apron areas. Taxiway centerline lights are steady burning and emit green light. c. Clearance Bar Lights. Clearance bar lights are installed at holding positions on taxiways in order to increase the conspicuity of the holding position in low visibility conditions. They may also be installed to indicate the location of an intersecting taxiway during periods of darkness. Clearance bars consist of three in−pavement steady−burning yellow lights. d. Runway Guard Lights. Runway guard lights are installed at taxiway/runway intersections. They are primarily used to enhance the conspicuity of taxiway/runway intersections during low visibility conditions, but may be used in all weather conditions. Runway guard lights consist of either a pair of elevated flashing yellow lights installed on either side of the taxiway, or a row of in−pavement yellow lights installed across the entire taxiway, at the runway holding position marking. NOTE− Some airports may have a row of three or five in−pavement yellow lights installed at taxiway/runway intersections. They should not be confused with clearance bar lights described in paragraph 2−1−10 c, Clearance Bar Lights. a. Taxiway Edge Lights. Taxiway edge lights are used to outline the edges of taxiways during periods of darkness or restricted visibility conditions. These fixtures emit blue light. e. Stop Bar Lights. Stop bar lights, when installed, are used to confirm the ATC clearance to enter or cross the active runway in low visibility conditions (below 1,200 ft Runway Visual Range). A stop bar consists of a row of red, unidirectional, steady−burning in−pavement lights installed across the entire taxiway at the runway holding position, and elevated steady−burning red lights on each side. A controlled stop bar is operated in conjunction with the taxiway centerline lead−on lights which extend from the stop bar toward the runway. Following the ATC clearance to proceed, the stop bar is turned off and the lead−on lights are turned on. The stop bar and lead−on lights are automatically reset by a sensor or backup timer. NOTE− At most major airports these lights have variable intensity settings and may be adjusted at pilot request or when deemed necessary by the controller. CAUTION− Pilots should never cross a red illuminated stop bar, even if an ATC clearance has been given to proceed onto or across the runway. b. Taxiway Centerline Lights. Taxiway centerline lights are used to facilitate ground traffic under low visibility conditions. They are located along the taxiway centerline in a straight line on straight NOTE− If after crossing a stop bar, the taxiway centerline lead−on lights inadvertently extinguish, pilots should hold their position and contact ATC for further instructions. 2−1−10. Taxiway Lights Airport Lighting Aids 2−1−13 6/17/21 AIM Section 2. Air Navigation and Obstruction Lighting 2−2−1. Aeronautical Light Beacons a. An aeronautical light beacon is a visual NAVAID displaying flashes of white and/or colored light to indicate the location of an airport, a heliport, a landmark, a certain point of a Federal airway in mountainous terrain, or an obstruction. The light used may be a rotating beacon or one or more flashing lights. The flashing lights may be supplemented by steady burning lights of lesser intensity. b. The color or color combination displayed by a particular beacon and/or its auxiliary lights tell whether the beacon is indicating a landing place, landmark, point of the Federal airways, or an obstruction. Coded flashes of the auxiliary lights, if employed, further identify the beacon site. 2−2−2. Code Beacons and Course Lights a. Code Beacons. The code beacon, which can be seen from all directions, is used to identify airports and landmarks. The code beacon flashes the three or four character airport identifier in International Morse Code six to eight times per minute. Green flashes are displayed for land airports while yellow flashes indicate water airports. b. Course Lights. The course light, which can be seen clearly from only one direction, is used only with rotating beacons of the Federal Airway System: two course lights, back to back, direct coded flashing beams of light in either direction along the course of airway. NOTE− Airway beacons are remnants of the “lighted” airways which antedated the present electronically equipped federal airways system. Only a few of these beacons exist today to mark airway segments in remote mountain areas. Flashes in Morse code identify the beacon site. 2−2−3. Obstruction Lights a. Obstructions are marked/lighted to warn airmen of their presence during daytime and nighttime conditions. They may be marked/lighted in any of the following combinations: Air Navigation and Obstruction Lighting 1. Aviation Red Obstruction Lights. Flashing aviation red beacons (20 to 40 flashes per minute) and steady burning aviation red lights during nighttime operation. Aviation orange and white paint is used for daytime marking. 2. Medium Intensity Flashing White Obstruction Lights. Medium intensity flashing white obstruction lights may be used during daytime and twilight with automatically selected reduced intensity for nighttime operation. When this system is used on structures 500 feet (153m) AGL or less in height, other methods of marking and lighting the structure may be omitted. Aviation orange and white paint is always required for daytime marking on structures exceeding 500 feet (153m) AGL. This system is not normally installed on structures less than 200 feet (61m) AGL. 3. High Intensity White Obstruction Lights. Flashing high intensity white lights during daytime with reduced intensity for twilight and nighttime operation. When this type system is used, the marking of structures with red obstruction lights and aviation orange and white paint may be omitted. 4. Dual Lighting. A combination of flashing aviation red beacons and steady burning aviation red lights for nighttime operation and flashing high intensity white lights for daytime operation. Aviation orange and white paint may be omitted. 5. Catenary Lighting. Lighted markers are available for increased night conspicuity of high− voltage (69KV or higher) transmission line catenary wires. Lighted markers provide conspicuity both day and night. b. Medium intensity omnidirectional flashing white lighting system provides conspicuity both day and night on catenary support structures. The unique sequential/simultaneous flashing light system alerts pilots of the associated catenary wires. c. High intensity flashing white lights are being used to identify some supporting structures of overhead transmission lines located across rivers, chasms, gorges, etc. These lights flash in a middle, top, lower light sequence at approximately 60 flashes per minute. The top light is normally installed near the top of the supporting structure, while the lower light indicates the approximate lower portion of the 2−2−1 7110.65R CHG 2 AIM AIM wire span. The lights are beamed towards the companion structure and identify the area of the wire span. d. High intensity flashing white lights are also employed to identify tall structures, such as chimneys and towers, as obstructions to air navigation. The lights provide a 360 degree coverage about the structure at 40 flashes per minute and consist of from one to seven levels of lights depending upon the height of the structure. Where more than one level is used the vertical banks flash simultaneously. 2−2−4. LED Lighting Systems Certain light−emitting diode (LED) lighting systems 2−2−2 3/15/07 5/19/22 6/17/21 fall outside the combined visible and near−infrared spectrum of night vision goggles (NVGs) and thus will not be visible to a flightcrew using NVGs. The FAA changed specifications for LED−based red obstruction lights to make them visible to pilots using certain NVG systems, however, other colors may not be visible. It is recommended that air carriers/operators —including Part 91 operators—who use NVGs incorporate procedures into manuals and/or standard operating procedures (SOPs) requiring periodic, unaided scanning when operating at low altitudes and when performing a reconnaissance of landing areas. Air Navigation and Obstruction Lighting 6/17/21 AIM Section 3. Airport Marking Aids and Signs 2−3−1. General 2−3−2. Airport Pavement Markings a. Airport pavement markings and signs provide information that is useful to a pilot during takeoff, landing, and taxiing. a. General. For the purpose of this section, the airport pavement markings have been grouped into four areas: 1. Runway Markings. b. Uniformity in airport markings and signs from one airport to another enhances safety and improves efficiency. Pilots are encouraged to work with the operators of the airports they use to achieve the marking and sign standards described in this section. 2. Taxiway Markings. 3. Holding Position Markings. 4. Other Markings. b. Marking Colors. Markings for runways are white. Markings defining the landing area on a heliport are also white except for hospital heliports which use a red “H” on a white cross. Markings for taxiways, areas not intended for use by aircraft (closed and hazardous areas), and holding positions (even if they are on a runway) are yellow. c. Pilots who encounter ineffective, incorrect, or confusing markings or signs on an airport should make the operator of the airport aware of the problem. These situations may also be reported under the Aviation Safety Reporting Program as described in Paragraph 7−7−1, Aviation Safety Reporting Program. Pilots may also report these situations to the FAA regional airports division. 2−3−3. Runway Markings d. The markings and signs described in this section of the AIM reflect the current FAA recommended standards. a. General. There are three types of markings for runways: visual, nonprecision instrument, and precision instrument. TBL 2−3−1 identifies the marking elements for each type of runway and TBL 2−3−2 identifies runway threshold markings. REFERENCE− AC 150/5340−1, Standards for Airport Markings. AC 150/5340−18, Standards for Airport Sign Systems. TBL 2−3−1 Runway Marking Elements Marking Element Visual Runway Designation X Centerline X X1 Threshold X2 Aiming Point Touchdown Zone Side Stripes 1 On runways used, or intended to be used, by international commercial transports. 2 Nonprecision Instrument Runway Precision Instrument Runway X X X X X X X X X X On runways 4,000 feet (1200 m) or longer used by jet aircraft. Airport Marking Aids and Signs 2−3−1 AIM 6/17/21 FIG 2−3−1 Precision Instrument Runway Markings b. Runway Designators. Runway numbers and letters are determined from the approach direction. The runway number is the whole number nearest one-tenth the magnetic azimuth of the centerline of the runway, measured clockwise from the magnetic north. The letters, differentiate between left (L), right (R), or center (C) parallel runways, as applicable: 1. For two parallel runways “L” “R.” 2. For three parallel runways “L” “C” “R.” c. Runway Centerline Marking. The runway centerline identifies the center of the runway and provides alignment guidance during takeoff and landings. The centerline consists of a line of uniformly spaced stripes and gaps. 2−3−2 d. Runway Aiming Point Marking. The aiming point marking serves as a visual aiming point for a landing aircraft. These two rectangular markings consist of a broad white stripe located on each side of the runway centerline and approximately 1,000 feet from the landing threshold, as shown in FIG 2−3−1, Precision Instrument Runway Markings. e. Runway Touchdown Zone Markers. The touchdown zone markings identify the touchdown zone for landing operations and are coded to provide distance information in 500 feet (150m) increments. These markings consist of groups of one, two, and three rectangular bars symmetrically arranged in pairs about the runway centerline, as shown in FIG 2−3−1. For runways having touchdown zone markings on both ends, those pairs of markings which extend to within 900 feet (270 m) of the midpoint between the thresholds are eliminated. Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−2 Nonprecision Instrument Runway and Visual Runway Markings AIMING POINT MARKING 20 THRESHOLD THRESHOLD MARKINGS DESIGNATION MARKING PAVEMENT EDGE NONPRECISION INSTRUMENT RUNWAY MARKINGS AIMING POINT MARKING 20 DESIGNATION MARKING THRESHOLD PAVEMENT EDGE VISUAL RUNWAY MARKINGS f. Runway Side Stripe Marking. Runway side stripes delineate the edges of the runway. They provide a visual contrast between runway and the abutting terrain or shoulders. Side stripes consist of continuous white stripes located on each side of the runway as shown in FIG 2−3−4. g. Runway Shoulder Markings. Runway shoulder stripes may be used to supplement runway side stripes to identify pavement areas contiguous to the runway sides that are not intended for use by aircraft. Runway shoulder stripes are yellow. (See FIG 2−3−5.) h. Runway Threshold Markings. Runway threshold markings come in two configurations. They either consist of eight longitudinal stripes of uniform Airport Marking Aids and Signs dimensions disposed symmetrically about the runway centerline (as shown in FIG 2−3−1) or the number of stripes is related to the runway width as indicated in TBL 2−3−2. A threshold marking helps identify the beginning of the runway that is available for landing. In some instances, the landing threshold may be relocated or displaced. TBL 2−3−2 Number of Runway Threshold Stripes Runway Width Number of Stripes 60 feet (18 m) 75 feet (23 m) 100 feet (30 m) 150 feet (45 m) 200 feet (60 m) 4 6 8 12 16 2−3−3 AIM 1. Relocation of a Threshold. Sometimes construction, maintenance, or other activities require the threshold to be relocated towards the rollout end of the runway. (See FIG 2−3−3.) When a threshold is relocated, it closes not only a set portion of the approach end of a runway, but also shortens the length of the opposite direction runway. In these cases, a NOTAM should be issued by the airport operator identifying the portion of the runway that is closed (for example, 10/28 W 900 CLSD). Because the duration of the relocation can vary from a few hours to several months, methods identifying the new threshold may vary. One common practice is to use a ten feet wide white threshold bar across the width of the runway. Although the runway lights in the area between the old threshold and new threshold will not be illuminated, the runway markings in this area may or may not be obliterated, removed, or covered. 2. Displaced Threshold. A displaced threshold is a threshold located at a point on the runway other than the designated beginning of the runway. Displacement of a threshold reduces the length of runway available for landings. The portion of runway behind a displaced threshold is available for takeoffs in either direction and landings from the opposite direction. A ten feet wide white threshold bar is 2−3−4 6/17/21 located across the width of the runway at the displaced threshold. White arrows are located along the centerline in the area between the beginning of the runway and displaced threshold. White arrow heads are located across the width of the runway just prior to the threshold bar, as shown in FIG 2−3−4. NOTE− Airport operator. When reporting the relocation or displacement of a threshold, the airport operator should avoid language which confuses the two. i. Demarcation Bar. A demarcation bar delineates a runway with a displaced threshold from a blast pad, stopway, or taxiway that precedes the runway. A demarcation bar is 3 feet (1m) wide and yellow, since it is not located on the runway, as shown in FIG 2−3−6. 1. Chevrons. These markings are used to show pavement areas aligned with the runway that are unusable for landing, takeoff, and taxiing. Chevrons are yellow. (See FIG 2−3−7.) j. Runway Threshold Bar. A threshold bar delineates the beginning of the runway that is available for landing when the threshold has been relocated or displaced. A threshold bar is 10 feet (3m) in width and extends across the width of the runway, as shown in FIG 2−3−4. Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−3 Relocation of a Threshold with Markings for Taxiway Aligned with Runway Airport Marking Aids and Signs 2−3−5 AIM 6/17/21 FIG 2−3−4 Displaced Threshold Markings 2−3−6 Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−5 Runway Shoulder Markings SHOULDER RUNWAY 45° SHOULDER 45° MIDPOINT OF RUNWAY 2. Enhanced Centerline. At some airports, mostly the larger commercial service airports, an enhanced taxiway centerline will be used. The enhanced taxiway centerline marking consists of a parallel line of yellow dashes on either side of the normal taxiway centerline. The taxiway centerlines are enhanced for a maximum of 150 feet prior to a runway holding position marking. The purpose of this enhancement is to warn the pilot that he/she is approaching a runway holding position marking and should prepare to stop unless he/she has been cleared onto or across the runway by ATC. (See FIG 2−3−8.) c. Taxiway Edge Markings. Taxiway edge markings are used to define the edge of the taxiway. They are primarily used when the taxiway edge does not correspond with the edge of the pavement. There are two types of markings depending upon whether the aircraft is supposed to cross the taxiway edge: 45° 45° RUNWAY THRESHOLD 2−3−4. Taxiway Markings a. General. All taxiways should have centerline markings and runway holding position markings whenever they intersect a runway. Taxiway edge markings are present whenever there is a need to separate the taxiway from a pavement that is not intended for aircraft use or to delineate the edge of the taxiway. Taxiways may also have shoulder markings and holding position markings for Instrument Landing System (ILS) critical areas and taxiway/ taxiway intersection markings. REFERENCE− AIM Paragraph 2−3−5 , Holding Position Markings b. Taxiway Centerline. 1. Normal Centerline. The taxiway centerline is a single continuous yellow line, 6 inches (15 cm) to 12 inches (30 cm) in width. This provides a visual cue to permit taxiing along a designated path. Ideally, the aircraft should be kept centered over this line during taxi. However, being centered on the taxiway centerline does not guarantee wingtip clearance with other aircraft or other objects. Airport Marking Aids and Signs 1. Continuous Markings. These consist of a continuous double yellow line, with each line being at least 6 inches (15 cm) in width spaced 6 inches (15 cm) apart. They are used to define the taxiway edge from the shoulder or some other abutting paved surface not intended for use by aircraft. 2. Dashed Markings. These markings are used when there is an operational need to define the edge of a taxiway or taxilane on a paved surface where the adjoining pavement to the taxiway edge is intended for use by aircraft (for example, an apron). Dashed taxiway edge markings consist of a broken double yellow line, with each line being at least 6 inches (15 cm) in width, spaced 6 inches (15 cm) apart (edge to edge). These lines are 15 feet (4.5 m) in length with 25 foot (7.5 m) gaps. (See FIG 2−3−9.) d. Taxi Shoulder Markings. Taxiways, holding bays, and aprons are sometimes provided with paved shoulders to prevent blast and water erosion. Although shoulders may have the appearance of full strength pavement, they are not intended for use by aircraft and may be unable to support an aircraft. Usually the taxiway edge marking will define this area. Where conditions exist such as islands or taxiway curves that may cause confusion as to which side of the edge stripe is for use by aircraft, taxiway shoulder markings may be used to indicate the pavement is unusable. Taxiway shoulder markings are yellow. (See FIG 2−3−10.) 2−3−7 AIM 6/17/21 FIG 2−3−6 Markings for Blast Pad or Stopway or Taxiway Preceding a Displaced Threshold 2−3−8 Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−7 Markings for Blast Pads and Stopways Airport Marking Aids and Signs 2−3−9 AIM 6/17/21 FIG 2−3−8 Enhanced Taxiway Centerline centerline, and signs indicating turns to the right being on the right side of the centerline. (See FIG 2−3−11.) FIG 2−3−10 Taxi Shoulder Markings RUNWAY PAVEMENT EDGE YELLOW STRIPES TAXIWAY EDGE MARKINGS FIG 2−3−9 Dashed Markings DOUBLE YELLOW LINES TAXIWAY EDGE MARKINGS CONTINUOUS TAXIWAY EDGE MARKINGS DASHED e. Surface Painted Taxiway Direction Signs. Surface painted taxiway direction signs have a yellow background with a black inscription, and are provided when it is not possible to provide taxiway direction signs at intersections, or when necessary to supplement such signs. These markings are located adjacent to the centerline with signs indicating turns to the left being on the left side of the taxiway 2−3−10 f. Surface Painted Location Signs. Surface painted location signs have a black background with a yellow inscription. When necessary, these markings are used to supplement location signs located along side the taxiway and assist the pilot in confirming the designation of the taxiway on which the aircraft is located. These markings are located on the right side of the centerline. (See FIG 2−3−11.) g. Geographic Position Markings. These markings are located at points along low visibility taxi routes designated in the airport’s Surface Movement Guidance Control System (SMGCS) plan. They are used to identify the location of taxiing aircraft during low visibility operations. Low visibility operations are those that occur when the runway visible range (RVR) is below 1200 feet (360m). They are positioned to the left of the taxiway centerline in the direction of taxiing. (See FIG 2−3−12.) The geographic position marking is a circle comprised of an outer black ring contiguous to a white ring with a pink circle in the middle. When installed on asphalt or other dark-colored pavements, the white ring and the black ring are reversed (i.e., the white ring becomes the outer ring and the black ring becomes the inner ring). It is designated with either a number or a number and letter. The number corresponds to the consecutive position of the marking on the route. Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−11 Surface Painted Signs Airport Marking Aids and Signs 2−3−11 AIM 2−3−5. Holding Position Markings a. Runway Holding Position Markings. For runways, these markings indicate where aircraft MUST STOP when approaching a runway. They consist of four yellow lines, two solid and two dashed, spaced six or twelve inches apart, and extending across the width of the taxiway or runway. The solid lines are always on the side where the aircraft must hold. There are three locations where runway holding position markings are encountered. 1. Runway Holding Position Markings on Taxiways. These markings identify the locations on a taxiway where aircraft MUST STOP when a clearance has not been issued to proceed onto the runway. Generally, runway holding position markings also identify the boundary of the runway safety area (RSA) for aircraft exiting the runway. Runway holding position markings are shown in FIG 2−3−13 and FIG 2−3−16. When instructed by ATC, “Hold short of Runway XX,” the pilot MUST STOP so that no part of the aircraft extends beyond the runway holding position marking. When approaching runways at airports with an operating control tower, pilots must not cross the runway holding position marking without ATC clearance. Pilots approaching runways at airports without an operating control tower must ensure adequate separation from other aircraft, vehicles, and pedestrians prior to crossing the holding position markings. An aircraft exiting a runway is not clear of the runway until all parts of the aircraft have crossed the applicable holding position marking. NOTE− Runway holding position markings identify the beginning of an RSA, and a pilot MUST STOP to get clearance before crossing (at airports with operating control towers). REFERENCE− AIM, Paragraph 4−3−20 , Exiting the Runway After Landing 2. Runway Holding Position Markings on Runways. These markings identify the locations on runways where aircraft MUST STOP. These markings are located on runways used by ATC for Land And Hold Short Operations (for example, see FIG 4−3−8) and Taxiing operations. For taxiing operations, the pilot MUST STOP prior to the holding position markings unless explicitly authorized to cross by ATC. A sign with a white inscription on a red background is located adjacent to these holding position markings. (See FIG 2−3−14.) The holding position markings are placed on runways prior to the intersection with another runway, or some designated 2−3−12 6/17/21 point. Pilots receiving and accepting instructions “Cleared to land Runway XX, hold short of Runway YY” from ATC must either exit Runway XX prior to the holding position markings, or stop at the holding position markings prior to Runway YY. Otherwise, pilots are authorized to use the entire landing length of the runway and disregard the holding position markings. 3. Holding Position Markings on Taxiways Located in Runway Approach Areas. These markings are used at some airports where it is necessary to hold an aircraft on a taxiway located in the approach or departure area of a runway so that the aircraft does not interfere with the operations on that runway. This marking is collocated with the runway approach/departure area holding position sign. When specifically instructed by ATC, “Hold short of Runway XX approach or Runway XX departure area,” the pilot MUST STOP so that no part of the aircraft extends beyond the holding position marking. (See Subparagraph 2−3−8b2, Runway Approach Area Holding Position Sign, and FIG 2−3−15.) b. Holding Position Markings for Instrument Landing System (ILS). Holding position markings for ILS critical areas consist of two yellow solid lines spaced two feet apart connected by pairs of solid lines spaced ten feet apart extending across the width of the taxiway as shown. (See FIG 2−3−16.) A sign with an inscription in white on a red background is located adjacent to these hold position markings. When instructed by ATC to hold short of the ILS critical area, pilots MUST STOP so that no part of the aircraft extends beyond the holding position marking. When approaching the holding position marking, pilots must not cross the marking without ATC clearance. The ILS critical area is not clear until all parts of the aircraft have crossed the applicable holding position marking. REFERENCE− AIM, Paragraph 1−1−9 , Instrument Landing System (ILS) c. Holding Position Markings for Intersecting Taxiways Holding position markings for intersecting taxiways consist of a single dashed line extending across the width of the taxiway as shown. (See FIG 2−3−17.) They are located on taxiways where ATC holds aircraft short of a taxiway intersection. When instructed by ATC, “Hold short of Taxiway XX,” the pilot MUST STOP so that no part of the aircraft extends beyond the holding position marking. When the marking is not present, the pilot MUST Airport Marking Aids and Signs 6/17/21 AIM STOP the aircraft at a point which provides adequate clearance from an aircraft on the intersecting taxiway. d. Surface Painted Holding Position Signs. Surface painted holding position signs have a red background with a white inscription and supplement the signs located at the holding position. This type of marking is normally used where the width of the holding position on the taxiway is greater than 200 feet (60 m). It is located to the left side of the taxiway centerline on the holding side and prior to the holding position marking. (See FIG 2−3−11.) FIG 2−3−12 Geographic Position Markings FIG 2−3−13 15 Runway Holding Position Markings on Taxiway RUNWAY HOLDING BAY TAXIWAY/RUNWAY HOLDING POSITION MARKINGS TAXIWAY EXAMPLE OF HOLDING POSITION MARKINGS EXTENDED ACROSS HOLDING BAY Airport Marking Aids and Signs 2−3−13 AIM 6/17/21 FIG 2−3−14 Runway Holding Position Markings on Runways 2−3−14 Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−15 Taxiways Located in Runway Approach Area Airport Marking Aids and Signs 2−3−15 AIM 6/17/21 FIG 2−3−16 Holding Position Markings: ILS Critical Area DETAIL 1 RUNWAY HOLDING POSITION MARKINGS, YELLOW, SEE DETAIL 1 ILS HOLDING POSITION MARKINGS, YELLOW, SEE DETAIL 2 ILS CRITICAL AREA DETAIL 2 2−3−6. Other Markings a. Vehicle Roadway Markings. The vehicle roadway markings are used when necessary to define a pathway for vehicle operations on or crossing areas that are also intended for aircraft. These markings consist of a white solid line to delineate each edge of the roadway and a dashed line to separate lanes within the edges of the roadway. In lieu of the solid lines, zipper markings may be used to delineate the edges of the vehicle roadway. (See FIG 2−3−18.) Details of the zipper markings are shown in FIG 2−3−19. b. VOR Receiver Checkpoint Markings. The VOR receiver checkpoint marking allows the pilot to check aircraft instruments with navigational aid signals. It consists of a painted circle with an arrow in 2−3−16 the middle; the arrow is aligned in the direction of the checkpoint azimuth. This marking, and an associated sign, is located on the airport apron or taxiway at a point selected for easy access by aircraft but where other airport traffic is not to be unduly obstructed. (See FIG 2−3−20.) NOTE− The associated sign contains the VOR station identification letter and course selected (published) for the check, the words “VOR check course,” and DME data (when applicable). The color of the letters and numerals are black on a yellow background. EXAMPLE− DCA 176−356 VOR check course DME XXX Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−17 Holding Position Markings: Taxiway/Taxiway Intersections TAXIWAY HOLDING POSITION MARKINGS, YELLOW, SEE DETAIL 1 DETAIL 1 FIG 2−3−18 Vehicle Roadway Markings Airport Marking Aids and Signs 2−3−17 AIM 6/17/21 FIG 2−3−19 FIG 2−3−20 Roadway Edge Stripes, White, Zipper Style Ground Receiver Checkpoint Markings 2 1 3 4 5 1. WHITE 2. YELLOW 3. YELLOW ARROW ALIGNED TOWARD THE FACILITY 4. INTERIOR OF CIRCLE BLACK (CONCRETE SURFACE ONLY) 5. CIRCLE MAY BE BORDERED ON INSIDE AND OUTSIDE WITH 6" BLACK BAND IF NECESSARY FOR CONTRAST FIG 2−3−21 Nonmovement Area Boundary Markings DASHED LINE ON MOVEMENT SIDE BOTH LINES ARE YELLOW SOLID LINE ON NONMOVEMENT SIDE FIG 2−3−22 Closed or Temporarily Closed Runway and Taxiway Markings c. Nonmovement Area Boundary Markings. These markings delineate the movement area (i.e., area under ATC). These markings are yellow and located on the boundary between the movement and nonmovement area. The nonmovement area boundary markings consist of two yellow lines (one solid and one dashed) 6 inches (15cm) in width. The solid line is located on the nonmovement area side, while the dashed yellow line is located on the movement area side. The nonmovement boundary marking area is shown in FIG 2−3−21. 2−3−18 X 2 d. Marking and Lighting of Permanently Closed Runways and Taxiways. For runways and taxiways which are permanently closed, the lighting circuits will be disconnected. The runway threshold, runway designation, and touchdown markings are obliterated and yellow crosses are placed at each end of the runway and at 1,000 foot intervals. (See FIG 2−3−22.) Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−23 Helicopter Landing Areas e. Temporarily Closed Runways and Taxiways. To provide a visual indication to pilots that a runway is temporarily closed, crosses are placed on the runway only at each end of the runway. The crosses are yellow in color. (See FIG 2−3−22.) 1. A raised lighted yellow cross may be placed on each runway end in lieu of the markings described in Subparagraph e,Temporarily Closed Runways and Taxiways, to indicate the runway is closed. 2. A visual indication may not be present depending on the reason for the closure, duration of the closure, airfield configuration, and the existence and the hours of operation of an airport traffic control tower. Pilots should check NOTAMs and the Automated Terminal Information System (ATIS) for local runway and taxiway closure information. 3. Temporarily closed taxiways are usually treated as hazardous areas, in which no part of an aircraft may enter, and are blocked with barricades. However, as an alternative, a yellow cross may be installed at each entrance to the taxiway. Airport Marking Aids and Signs f. Helicopter Landing Areas. The markings illustrated in FIG 2−3−23 are used to identify the landing and takeoff area at a public use heliport and hospital heliport. The letter “H” in the markings is oriented to align with the intended direction of approach. FIG 2−3−23 also depicts the markings for a closed airport. 2−3−7. Airport Signs There are six types of signs installed on airfields: mandatory instruction signs, location signs, direction signs, destination signs, information signs, and runway distance remaining signs. The characteristics and use of these signs are discussed in Paragraph 2−3−8, Mandatory Instruction Signs, through Paragraph 2−3−13, Runway Distance Remaining Signs. REFERENCE− AC150/5340−18, Standards for Airport Sign Systems for Detailed Information on Airport Signs. 2−3−19 AIM 6/17/21 FIG 2−3−24 Runway Holding Position Sign FIG 2−3−25 Holding Position Sign at Beginning of Takeoff Runway 2−3−8. Mandatory Instruction Signs a. These signs have a red background with a white inscription and are used to denote: 1. An entrance to a runway or critical area; and 2. Areas where an aircraft is prohibited from entering. b. Typical mandatory signs and applications are: 1. Runway Holding Position Sign. This sign is located at the holding position on taxiways that intersect a runway or on runways that intersect other 2−3−20 runways. The inscription on the sign contains the designation of the intersecting runway, as shown in FIG 2−3−24. The runway numbers on the sign are arranged to correspond to the respective runway threshold. For example, “15−33” indicates that the threshold for Runway 15 is to the left and the threshold for Runway 33 is to the right. (a) On taxiways that intersect the beginning of the takeoff runway, only the designation of the takeoff runway may appear on the sign (as shown in FIG 2−3−25), while all other signs will have the designation of both runway directions. Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−26 Holding Position Sign for a Taxiway that Intersects the Intersection of Two Runways FIG 2−3−27 Holding Position Sign for a Runway Approach Area (b) If the sign is located on a taxiway that intersects the intersection of two runways, the designations for both runways will be shown on the sign along with arrows showing the approximate alignment of each runway, as shown in FIG 2−3−26. In addition to showing the approximate runway alignment, the arrow indicates the direction to the threshold of the runway whose designation is immediately next to the arrow. (c) A runway holding position sign on a taxiway will be installed adjacent to holding position markings on the taxiway pavement. On runways, holding position markings will be located only on the runway pavement adjacent to the sign, if the runway is normally used by ATC for “Land, Hold Short” operations or as a taxiway. The holding position Airport Marking Aids and Signs markings are described in Paragraph 2−3−5, Holding Position Markings. 2. Runway Approach Area Holding Position Sign. At some airports, it is necessary to hold an aircraft on a taxiway located in the approach or departure area for a runway so that the aircraft does not interfere with operations on that runway. In these situations, a sign with the designation of the approach end of the runway followed by a “dash” (−) and letters “APCH” will be located at the holding position on the taxiway. Holding position markings in accordance with Paragraph 2−3−5, Holding Position Markings, will be located on the taxiway pavement. An example of this sign is shown in FIG 2−3−27. In this example, the sign may protect the approach to Runway 15 and/or the departure for Runway 33. 2−3−21 AIM 6/17/21 FIG 2−3−28 Holding Position Sign for ILS Critical Area FIG 2−3−29 Sign Prohibiting Aircraft Entry into an Area 3. ILS Critical Area Holding Position Sign. At some airports, when the instrument landing system is being used, it is necessary to hold an aircraft on a taxiway at a location other than the holding position described in Paragraph 2−3−5, Holding Position Markings. In these situations, the holding position sign for these operations will have the inscription “ILS” and be located adjacent to the holding position marking on the taxiway described in paragraph 2−3−5. An example of this sign is shown in FIG 2−3−28. 4. No Entry Sign. This sign, shown in FIG 2−3−29, prohibits an aircraft from entering an area. Typically, this sign would be located on a taxiway intended to be used in only one direction or at the intersection of vehicle roadways with runways, taxiways, or aprons where the roadway may be mistaken as a taxiway or other aircraft movement surface. NOTE− Holding position signs provide the pilot with a visual cue as to the location of the holding position marking. REFERENCE− AIM Paragraph 2−3−5, Holding Position Markings 2−3−22 Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−30 Taxiway Location Sign FIG 2−3−31 Taxiway Location Sign Collocated with Runway Holding Position Sign 2−3−9. Location Signs a. Location signs are used to identify either a taxiway or runway on which the aircraft is located. Other location signs provide a visual cue to pilots to assist them in determining when they have exited an area. The various location signs are described below. Airport Marking Aids and Signs 1. Taxiway Location Sign. This sign has a black background with a yellow inscription and yellow border, as shown in FIG 2−3−30. The inscription is the designation of the taxiway on which the aircraft is located. These signs are installed along taxiways either by themselves or in conjunction with direction signs or runway holding position signs. (See FIG 2−3−35 and FIG 2−3−31.) 2−3−23 AIM 6/17/21 FIG 2−3−32 Runway Location Sign FIG 2−3−33 Runway Boundary Sign 2. Runway Location Sign. This sign has a black background with a yellow inscription and yellow border, as shown in FIG 2−3−32. The inscription is the designation of the runway on which the aircraft is located. These signs are intended to complement the information available to pilots through their magnetic compass and typically are installed where the proximity of two or more runways to one another could cause pilots to be confused as to which runway they are on. 2−3−24 3. Runway Boundary Sign. This sign has a yellow background with a black inscription with a graphic depicting the pavement holding position marking, as shown in FIG 2−3−33. This sign, which faces the runway and is visible to the pilot exiting the runway, is located adjacent to the holding position marking on the pavement. The sign is intended to provide pilots with another visual cue which they can use as a guide in deciding when they are “clear of the runway.” Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−34 ILS Critical Area Boundary Sign 4. ILS Critical Area Boundary Sign. This sign has a yellow background with a black inscription with a graphic depicting the ILS pavement holding position marking as shown in FIG 2−3−34. This sign is located adjacent to the ILS holding position marking on the pavement and can be seen by pilots leaving the critical area. The sign is intended to provide pilots with another visual cue which they can use as a guide in deciding when they are “clear of the ILS critical area.” 2−3−10. Direction Signs a. Direction signs have a yellow background with a black inscription. The inscription identifies the designation(s) of the intersecting taxiway(s) leading out of the intersection that a pilot would normally be expected to turn onto or hold short of. Each designation is accompanied by an arrow indicating the direction of the turn. b. Except as noted in subparagraph e, each taxiway designation shown on the sign is accompanied by only one arrow. When more than one taxiway designation is shown on the sign, each designation and its associated arrow is separated from the other Airport Marking Aids and Signs taxiway designations by either a vertical message divider or a taxiway location sign as shown in FIG 2−3−35. c. Direction signs are normally located on the left prior to the intersection. When used on a runway to indicate an exit, the sign is located on the same side of the runway as the exit. FIG 2−3−36 shows a direction sign used to indicate a runway exit. d. The taxiway designations and their associated arrows on the sign are arranged clockwise starting from the first taxiway on the pilot’s left. (See FIG 2−3−35.) e. If a location sign is located with the direction signs, it is placed so that the designations for all turns to the left will be to the left of the location sign; the designations for continuing straight ahead or for all turns to the right would be located to the right of the location sign. (See FIG 2−3−35.) f. When the intersection is comprised of only one crossing taxiway, it is permissible to have two arrows associated with the crossing taxiway, as shown in FIG 2−3−37. In this case, the location sign is located to the left of the direction sign. 2−3−25 AIM 6/17/21 FIG 2−3−35 Direction Sign Array with Location Sign on Far Side of Intersection FIG 2−3−36 Direction Sign for Runway Exit 2−3−26 Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−37 Direction Sign Array for Simple Intersection Airport Marking Aids and Signs 2−3−27 AIM 6/17/21 FIG 2−3−38 Destination Sign for Military Area FIG 2−3−39 Destination Sign for Common Taxiing Route to Two Runways 2−3−11. Destination Signs a. Destination signs also have a yellow background with a black inscription indicating a destination on the airport. These signs always have an arrow showing the direction of the taxiing route to that destination. FIG 2−3−38 is an example of a typical destination sign. When the arrow on the destination sign indicates a turn, the sign is located prior to the intersection. b. Destinations commonly shown on these types of signs include runways, aprons, terminals, military areas, civil aviation areas, cargo areas, international 2−3−28 areas, and fixed base operators. An abbreviation may be used as the inscription on the sign for some of these destinations. c. When the inscription for two or more destinations having a common taxiing route are placed on a sign, the destinations are separated by a “dot” () and one arrow would be used, as shown in FIG 2−3−39. When the inscription on a sign contains two or more destinations having different taxiing routes, each destination will be accompanied by an arrow and will be separated from the other destinations on the sign with a vertical black message divider, as shown in FIG 2−3−40. Airport Marking Aids and Signs 6/17/21 AIM FIG 2−3−40 Destination Sign for Different Taxiing Routes to Two Runways 2−3−12. Information Signs Information signs have a yellow background with a black inscription. They are used to provide the pilot with information on such things as areas that cannot be seen from the control tower, applicable radio frequencies, and noise abatement procedures. The airport operator determines the need, size, and location for these signs. 2−3−13. Runway Distance Remaining Signs Runway distance remaining signs have a black background with a white numeral inscription and may be installed along one or both side(s) of the runway. The number on the signs indicates the distance (in thousands of feet) of landing runway remaining. The last sign (i.e., the sign with the numeral “1”) will be located at least 950 feet from the runway end. FIG 2−3−41 shows an example of a runway distance remaining sign. Airport Marking Aids and Signs FIG 2−3−41 Runway Distance Remaining Sign Indicating 3,000 feet of Runway Remaining 3 2−3−29 AIM 6/17/21 2−3−14. Aircraft Arresting Systems a. Certain airports are equipped with a means of rapidly stopping military aircraft on a runway. This equipment, normally referred to as EMERGENCY ARRESTING GEAR, generally consists of pendant cables supported over the runway surface by rubber “donuts.” Although most devices are located in the overrun areas, a few of these arresting systems have cables stretched over the operational areas near the ends of a runway. b. Arresting cables which cross over a runway require special markings on the runway to identify the cable location. These markings consist of 10 feet diameter solid circles painted “identification yellow,” 30 feet on center, perpendicular to the runway centerline across the entire runway width. Additional details are contained in AC 150/5220−9, Aircraft Arresting Systems for Joint Civil/Military Airports. NOTE− Aircraft operations on the runway are not restricted by the installation of aircraft arresting devices. c. Engineered Materials Arresting Systems (EMAS). EMAS, which is constructed of high energy−absorbing materials of selected strength, is located in the safety area beyond the end of the runway. EMAS will be marked with yellow chevrons. EMAS is designed to crush under the weight of commercial aircraft and will exert deceleration forces on the landing gear. These systems do not affect the normal landing and takeoff of airplanes. More information concerning EMAS is in AC 150/5220−22, Engineered Materials Arresting Systems (EMAS) for Aircraft Overruns. NOTE− EMAS may be located as close as 35 feet beyond the end of the runway. Aircraft and ground vehicles should never taxi or drive across the EMAS or beyond the end of the runway if EMAS is present. FIG 2−3−42 Engineered Materials Arresting System (EMAS) 2−3−30 Airport Marking Aids and Signs 6/17/21 2−3−15. Security Identification Display Area (SIDA) a. Security Identification Display Areas (SIDA) are limited access areas that require a badge issued in accordance with procedures in 49 CFR Part 1542. A SIDA can include the Air Operations Area (AOA), e.g., aircraft movement area or parking area, or a Secured Area, such as where commercial passengers enplane. The AOA may not be a SIDA, but a Secured Area is always a SIDA. Movement through or into a SIDA is prohibited without authorization and proper identification being displayed. If you are unsure of the location of a SIDA, contact the airport authority for additional information. Airports that have a SIDA will have a description and map detailing boundaries and pertinent features available. AIM civil and criminal fines and prosecution. Pilots are advised to brief passengers accordingly. Report suspicious activity to the TSA by calling AOPA’s Airport Watch Program, 866−427−3287. 49 CFR 1540 requires each individual who holds an airman certificate, medical certificate, authorization, or license issued by the FAA to present it for inspection upon a request from TSA. FIG 2−3−43 Sample SIDA Warning Sign b. Pilots or passengers without proper identification that are observed entering a SIDA may be reported to the Transportation Security Administration (TSA) or airport security and may be subject to Airport Marking Aids and Signs 2−3−31 6/17/21 AIM Chapter 3. Airspace Section 1. General 3−1−1. General a. There are two categories of airspace or airspace areas: 1. Regulatory (Class A, B, C, D and E airspace areas, restricted and prohibited areas); and 2. Nonregulatory (military operations areas [MOA], warning areas, alert areas, controlled firing areas [CFA], and national security areas [NSA]). NOTE− Additional information on special use airspace (prohibited areas, restricted areas [permanent or temporary], warning areas, MOAs [permanent or temporary], alert areas, CFAs, and NSAs) may be found in Chapter 3, Airspace, Section 4, Special Use Airspace, paragraphs 3−4−1 through 3−4−8 . b. Within these two categories, there are four types: 1. Controlled, 2. Uncontrolled, 3−1−2. General Dimensions of Airspace Segments Refer to Title 14 of the U.S. Code of Federal Regulations (CFR) for specific dimensions, exceptions, geographical areas covered, exclusions, specific transponder/ADS−B or other equipment requirements, and flight operations. 3−1−3. Hierarchy of Overlapping Airspace Designations a. When overlapping airspace designations apply to the same airspace, the operating rules associated with the more restrictive airspace designation apply. b. For the purpose of clarification: 1. Class A airspace is more restrictive than Class B, Class C, Class D, Class E, or Class G airspace; 2. Class B airspace is more restrictive than Class C, Class D, Class E, or Class G airspace; 3. Class C airspace is more restrictive than Class D, Class E, or Class G airspace; 3. Special use, and 4. Class D airspace is more restrictive than Class E or Class G airspace; and 4. Other airspace. 5. Class E is more restrictive than Class G airspace. c. The categories and types of airspace are dictated by: 1. The complexity or density of aircraft movements, 2. The nature of the operations conducted within the airspace, 3. The level of safety required, and 4. The national and public interest. d. It is important that pilots be familiar with the operational requirements for each of the various types or classes of airspace. Subsequent sections will cover each class in sufficient detail to facilitate understanding. General 3−1−4. Basic VFR Weather Minimums a. No person may operate an aircraft under basic VFR when the flight visibility is less, or at a distance from clouds that is less, than that prescribed for the corresponding altitude and class of airspace. (See TBL 3−1−1.) NOTE− Student pilots must comply with 14 CFR Section 61.89(a) (6) and (7). b. Except as provided in 14 CFR Section 91.157, Special VFR Weather Minimums, no person may operate an aircraft beneath the ceiling under VFR within the lateral boundaries of controlled airspace designated to the surface for an airport when the ceiling is less than 1,000 feet. (See 14 CFR Section 91.155(c).) 3−1−1 AIM 6/17/21 TBL 3−1−1 Basic VFR Weather Minimums Airspace Flight Visibility Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Not Applicable Class B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 statute miles Class C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 statute miles Class D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 statute miles Class E Less than 10,000 feet MSL . . . . . . . . . . . . . . . . . . . . . . . . 3 statute miles At or above 10,000 feet MSL . . . . . . . . . . . . . . . . . . . . . . 5 statute miles Distance from Clouds Not Applicable Clear of Clouds 500 feet below 1,000 feet above 2,000 feet horizontal 500 feet below 1,000 feet above 2,000 feet horizontal 500 feet below 1,000 feet above 2,000 feet horizontal 1,000 feet below 1,000 feet above 1 statute mile horizontal Class G 1,200 feet or less above the surface (regardless of MSL altitude). For aircraft other than helicopters: Day, except as provided in §91.155(b) . . . . . . . . . . . . . . . 1 statute mile Night, except as provided in §91.155(b) . . . . . . . . . . . . . . 3 statute miles For helicopters: Day . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ½ statute mile Night, except as provided in §91.155(b) . . . . . . . . . . . . . . 1 statute mile More than 1,200 feet above the surface but less than 10,000 feet MSL. Day . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 statute mile Night . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 statute miles More than 1,200 feet above the surface and at or above 5 statute miles 10,000 feet MSL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clear of clouds 500 feet below 1,000 feet above 2,000 feet horizontal Clear of clouds Clear of clouds 500 feet below 1,000 feet above 2,000 feet horizontal 500 feet below 1,000 feet above 2,000 feet horizontal 1,000 feet below 1,000 feet above 1 statute mile horizontal 3−1−5. VFR Cruising Altitudes and Flight Levels (See TBL 3−1−2.) 3−1−2 General 6/17/21 AIM TBL 3−1−2 VFR Cruising Altitudes and Flight Levels If your magnetic course (ground track) is: 0 to 179 . . . . . . . . . . . . . . . . 180 to 359 . . . . . . . . . . . . . . General And you are more than 3,000 feet above the surface but below 18,000 feet MSL, fly: Odd thousands MSL, plus 500 feet (3,500; 5,500; 7,500, etc.) Even thousands MSL, plus 500 feet (4,500; 6,500; 8,500, etc.) And you are above 18,000 feet MSL to FL 290, fly: Odd Flight Levels plus 500 feet (FL 195; FL 215; FL 235, etc.) Even Flight Levels plus 500 feet (FL 185; FL 205; FL 225, etc.) 3−1−3 6/17/21 AIM Section 2. Controlled Airspace 3−2−1. General a. Controlled Airspace. A generic term that covers the different classification of airspace (Class A, Class B, Class C, Class D, and Class E airspace) and defined dimensions within which air traffic control service is provided to IFR flights and to VFR flights in accordance with the airspace classification. (See FIG 3−2−1.) b. IFR Requirements. IFR operations in any class of controlled airspace requires that a pilot must file an IFR flight plan and receive an appropriate ATC clearance. c. IFR Separation. Standard IFR separation is provided to all aircraft operating under IFR in controlled airspace. d. VFR Requirements. It is the responsibility of the pilot to ensure that ATC clearance or radio communication requirements are met prior to entry into Class B, Class C, or Class D airspace. The pilot retains this responsibility when receiving ATC radar advisories. (See 14 CFR Part 91.) e. Traffic Advisories. Traffic advisories will be provided to all aircraft as the controller’s work situation permits. f. Safety Alerts. Safety Alerts are mandatory services and are provided to ALL aircraft. There are two types of Safety Alerts: 1. Terrain/Obstruction Alert. A Terrain/ Obstruction Alert is issued when, in the controller’s judgment, an aircraft’s altitude places it in unsafe proximity to terrain and/or obstructions; and 2. Aircraft Conflict/Mode C Intruder Alert. An Aircraft Conflict/Mode C Intruder Alert is issued if the controller observes another aircraft which places it in an unsafe proximity. When feasible, the controller will offer the pilot an alternative course of action. FIG 3−2−1 Airspace Classes FL 600 18,000 MSL CLASS A 14,500 MSL CLASS E CLASS B CLASS C Nontowered Airport 1,200 AGL 700 AGL CLASS G CLASS G CLASS CL ASS D CLASS G MSL - mean sea level AGL - above ground level FL - flight level Controlled Airspace 3−2−1 AIM g. Ultralight Vehicles. No person may operate an ultralight vehicle within Class A, Class B, Class C, or Class D airspace or within the lateral boundaries of the surface area of Class E airspace designated for an airport unless that person has prior authorization from the ATC facility having jurisdiction over that airspace. (See 14 CFR Part 103.) h. Unmanned Free Balloons. Unless otherwise authorized by ATC, no person may operate an unmanned free balloon below 2,000 feet above the surface within the lateral boundaries of Class B, Class C, Class D, or Class E airspace designated for an airport. (See 14 CFR Part 101.) i. Parachute Jumps. No person may make a parachute jump, and no pilot−in−command may allow a parachute jump to be made from that aircraft, in or into Class A, Class B, Class C, or Class D airspace without, or in violation of, the terms of an ATC authorization issued by the ATC facility having jurisdiction over the airspace. (See 14 CFR Part 105.) 3−2−2. Class A Airspace a. Definition. Generally, that airspace from 18,000 feet MSL up to and including FL 600, including the airspace overlying the waters within 12 nautical miles off the coast of the 48 contiguous States and Alaska; and designated international airspace beyond 12 nautical miles off the coast of the 48 contiguous States and Alaska within areas of domestic radio navigational signal or ATC radar coverage, and within which domestic procedures are applied. b. Operating Rules and Pilot/Equipment Requirements. Unless otherwise authorized, all persons must operate their aircraft under IFR. (See 14 CFR Section 71.33, Sections 91.167 through 91.193, Sections 91.215 through 91.217, and Sections 91.225 through 91.227.) c. Charts. Class A airspace is not specifically charted. 3−2−3. Class B Airspace a. Definition. Generally, that airspace from the surface to 10,000 feet MSL surrounding the nation’s busiest airports in terms of IFR operations or passenger enplanements. The configuration of each Class B airspace area is individually tailored and 3−2−2 6/17/21 consists of a surface area and two or more layers (some Class B airspace areas resemble upside-down wedding cakes), and is designed to contain all published instrument procedures once an aircraft enters the airspace. An ATC clearance is required for all aircraft to operate in the area, and all aircraft that are so cleared receive separation services within the airspace. The cloud clearance requirement for VFR operations is “clear of clouds.” b. Operating Rules and Pilot/Equipment Requirements. Regardless of weather conditions, an ATC clearance is required prior to operating within Class B airspace. Pilots should not request a clearance to operate within Class B airspace unless the requirements of 14 CFR Sections 91.131, 91.215, and 91.225 are met. Included among these requirements are: 1. Unless otherwise authorized by ATC, aircraft must be equipped with an operable two-way radio capable of communicating with ATC on appropriate frequencies for that Class B airspace. 2. No person may take off or land a civil aircraft at the following primary airports within Class B airspace unless the pilot−in−command holds at least a private pilot certificate: (a) Andrews Air Force Base, MD (b) Atlanta Hartsfield Airport, GA (c) Boston Logan Airport, MA (d) Chicago O’Hare Intl. Airport, IL (e) Dallas/Fort Worth Intl. Airport, TX (f) Los Angeles Intl. Airport, CA (g) Miami Intl. Airport, FL (h) Newark Intl. Airport, NJ (i) New York Kennedy Airport, NY (j) New York La Guardia Airport, NY (k) Ronald Reagan Washington National Airport, DC (l) San Francisco Intl. Airport, CA 3. No person may take off or land a civil aircraft at an airport within Class B airspace or operate a civil aircraft within Class B airspace unless: (a) The pilot−in−command holds at least a private pilot certificate; or Controlled Airspace 6/17/21 (b) The pilot−in−command holds a recreational pilot certificate and has met the requirements of 14 CFR Section 61.101; or (c) The pilot−in−command holds a sport pilot certificate and has met the requirements of 14 CFR Section 61.325; or (d) The aircraft is operated by a student pilot: (1) Who seeks a private pilot certificate and has met the requirements of 14 CFR Section 61.95. (2) Who seeks a recreational pilot or sport pilot certificate and has met the requirements of 14 CFR Section 61.94. 4. Unless otherwise authorized by ATC, each person operating a large turbine engine-powered airplane to or from a primary airport must operate at or above the designated floors while within the lateral limits of Class B airspace. 5. Unless otherwise authorized by ATC, each aircraft must be equipped as follows: (a) For IFR operations, an operable VOR or TACAN receiver or an operable and suitable RNAV system; and (b) For all operations, a two-way radio capable of communications with ATC on appropriate frequencies for that area; and (c) Unless otherwise authorized by ATC, an operable radar beacon transponder with automatic altitude reporting capability and operable ADS−B Out equipment. NOTE− ATC may, upon notification, immediately authorize a deviation from the altitude reporting equipment requirement; however, a request for a deviation from the 4096 transponder equipment requirement must be submitted to the controlling ATC facility at least one hour before the proposed operation. A request for a deviation from the ADS−B equipage requirement must be submitted using the FAA’s automated web authorization tool at least one hour but not more than 24 hours before the proposed operation. REFERENCE− AIM, Paragraph 4−1−20 , Transponder and ADS−B Out Operation AC 90−114, Automatic Dependent Surveillance−Broadcast Operations 6. Mode C Veil. The airspace within 30 nautical miles of an airport listed in Appendix D, Section 1 of 14 CFR Part 91 (generally primary airports within Class B airspace areas), from the surface upward to 10,000 feet MSL. Unless otherwise authorized by Controlled Airspace AIM ATC, aircraft operating within this airspace must be equipped with an operable radar beacon transponder with automatic altitude reporting capability and operable ADS−B Out equipment. However, aircraft that were not originally certificated with an engine−driven electrical system or that have not subsequently been certified with a system installed may conduct operations within a Mode C veil provided the aircraft remains outside Class A, B or C airspace; and below the altitude of the ceiling of a Class B or Class C airspace area designated for an airport or 10,000 feet MSL, whichever is lower. c. Charts. Class B airspace is charted on Sectional Charts, IFR En Route Low Altitude, and Terminal Area Charts. d. Flight Procedures. 1. Flights. Aircraft within Class B airspace are required to operate in accordance with current IFR procedures. A clearance for a visual approach to a primary airport is not authorization for turbine− powered airplanes to operate below the designated floors of the Class B airspace. 2. VFR Flights. (a) Arriving aircraft must obtain an ATC clearance prior to entering Class B airspace and must contact ATC on the appropriate frequency, and in relation to geographical fixes shown on local charts. Although a pilot may be operating beneath the floor of the Class B airspace on initial contact, communications with ATC should be established in relation to the points indicated for spacing and sequencing purposes. (b) Departing aircraft require a clearance to depart Class B airspace and should advise the clearance delivery position of their intended altitude and route of flight. ATC will normally advise VFR aircraft when leaving the geographical limits of the Class B airspace. Radar service is not automatically terminated with this advisory unless specifically stated by the controller. (c) Aircraft not landing or departing the primary airport may obtain an ATC clearance to transit the Class B airspace when traffic conditions permit and provided the requirements of 14 CFR Section 91.131 are met. Such VFR aircraft are encouraged, to the extent possible, to operate at altitudes above or below the Class B airspace or transit through established VFR corridors. Pilots 3−2−3 AIM 6/17/21 operating in VFR corridors are urged to use frequency 122.750 MHz for the exchange of aircraft position information. e. ATC Clearances and Separation. An ATC clearance is required to enter and operate within Class B airspace. VFR pilots are provided sequencing and separation from other aircraft while operating within Class B airspace. REFERENCE− AIM, Paragraph 4−1−18 , Terminal Radar Services for VFR Aircraft NOTE− 1. Separation and sequencing of VFR aircraft will be suspended in the event of a radar outage as this service is dependent on radar. The pilot will be advised that the service is not available and issued wind, runway information and the time or place to contact the tower. 2. Separation of VFR aircraft will be suspended during CENRAP operations. Traffic advisories and sequencing to the primary airport will be provided on a workload permitting basis. The pilot will be advised when center radar presentation (CENRAP) is in use. 1. VFR aircraft are separated from all VFR/IFR aircraft which weigh 19,000 pounds or less by a minimum of: (a) Target resolution, or (b) 500 feet vertical separation, or (c) Visual separation. 2. VFR aircraft are separated from all VFR/IFR aircraft which weigh more than 19,000 and turbojets by no less than: (a) 1 1/2 miles lateral separation, or (b) 500 feet vertical separation, or (c) Visual separation. 3. This program is not to be interpreted as relieving pilots of their responsibilities to see and avoid other traffic operating in basic VFR weather conditions, to adjust their operations and flight path as necessary to preclude serious wake encounters, to maintain appropriate terrain and obstruction clearance or to remain in weather conditions equal to or better than the minimums required by 14 CFR Section 91.155. Approach control should be advised and a revised clearance or instruction obtained when compliance with an assigned route, heading and/or altitude is likely to compromise pilot responsibility 3−2−4 with respect to terrain and obstruction clearance, vortex exposure, and weather minimums. 4. ATC may assign altitudes to VFR aircraft that do not conform to 14 CFR Section 91.159. “RESUME APPROPRIATE VFR ALTITUDES” will be broadcast when the altitude assignment is no longer needed for separation or when leaving Class B airspace. Pilots must return to an altitude that conforms to 14 CFR Section 91.159. f. Proximity operations. VFR aircraft operating in proximity to Class B airspace are cautioned against operating too closely to the boundaries, especially where the floor of the Class B airspace is 3,000 feet or less above the surface or where VFR cruise altitudes are at or near the floor of higher levels. Observance of this precaution will reduce the potential for encountering an aircraft operating at the altitudes of Class B floors. Additionally, VFR aircraft are encouraged to utilize the VFR Planning Chart as a tool for planning flight in proximity to Class B airspace. Charted VFR Flyway Planning Charts are published on the back of the existing VFR Terminal Area Charts. 3−2−4. Class C Airspace a. Definition. Generally, that airspace from the surface to 4,000 feet above the airport elevation (charted in MSL) surrounding those airports that have an operational control tower, are serviced by a radar approach control, and that have a certain number of IFR operations or passenger enplanements. Although the configuration of each Class C airspace area is individually tailored, the airspace usually consists of a 5 NM radius core surface area that extends from the surface up to 4,000 feet above the airport elevation, and a 10 NM radius shelf area that extends no lower than 1,200 feet up to 4,000 feet above the airport elevation. b. Charts. Class C airspace is charted on Sectional Charts, IFR En Route Low Altitude, and Terminal Area Charts where appropriate. c. Operating Rules and Pilot/Equipment Requirements: 1. Pilot Certification. No specific certification required. 2. Equipment. (a) Two-way radio; and Controlled Airspace 6/17/21 (b) Unless otherwise authorized by ATC, an operable radar beacon transponder with automatic altitude reporting capability and operable ADS−B Out equipment. NOTE− See Paragraph 4−1−20, Transponder and ADS−B Out Operation, subparagraph f for Mode C transponder/ ADS−B requirements for operating above Class C airspace. 3. Arrival or Through Flight Entry Requirements. Two-way radio communication must be established with the ATC facility providing ATC services prior to entry and thereafter maintain those communications while in Class C airspace. Pilots of arriving aircraft should contact the Class C airspace ATC facility on the publicized frequency and give their position, altitude, radar beacon code, destination, and request Class C service. Radio contact should be initiated far enough from the Class C airspace boundary to preclude entering Class C airspace before two-way radio communications are established. NOTE− 1. If the controller responds to a radio call with, “(aircraft callsign) standby,” radio communications have been established and the pilot can enter the Class C airspace. 2. If workload or traffic conditions prevent immediate provision of Class C services, the controller will inform the pilot to remain outside the Class C airspace until conditions permit the services to be provided. 3. It is important to understand that if the controller responds to the initial radio call without using the aircraft identification, radio communications have not been established and the pilot may not enter the Class C airspace. 4. Class C airspace areas have a procedural Outer Area. Normally this area is 20 NM from the primary Class C airspace airport. Its vertical limit extends from the lower limits of radio/radar coverage up to the ceiling of the approach control’s delegated airspace, excluding the Class C airspace itself, and other airspace as appropriate. (This outer area is not charted.) 5. Pilots approaching an airport with Class C service should be aware that if they descend below the base altitude of the 5 to 10 mile shelf during an instrument or visual approach, they may encounter non−transponder/non− ADS−B VFR aircraft. EXAMPLE− 1. [Aircraft callsign] “remain outside the Class Charlie airspace and standby.” Controlled Airspace AIM 2. “Aircraft calling Dulles approach control, standby.” 4. Departures from: (a) A primary or satellite airport with an operating control tower. Two-way radio communications must be established and maintained with the control tower, and thereafter as instructed by ATC while operating in Class C airspace. (b) A satellite airport without an operating control tower. Two-way radio communications must be established as soon as practicable after departing with the ATC facility having jurisdiction over the Class C airspace. 5. Aircraft Speed. Unless otherwise authorized or required by ATC, no person may operate an aircraft at or below 2,500 feet above the surface within 4 nautical miles of the primary airport of a Class C airspace area at an indicated airspeed of more than 200 knots (230 mph). d. Air Traffic Services. When two-way radio communications and radar contact are established, all VFR aircraft are: 1. Sequenced to the primary airport. 2. Provided Class C services within the Class C airspace and the outer area. 3. Provided basic radar services beyond the outer area on a workload permitting basis. This can be terminated by the controller if workload dictates. e. Aircraft Separation. Separation is provided within the Class C airspace and the outer area after two-way radio communications and radar contact are established. VFR aircraft are separated from IFR aircraft within the Class C airspace by any of the following: 1. Visual separation. 2. 500 feet vertical separation. 3. Target resolution. 4. Wake turbulence separation will be provided to all aircraft operating: (a) Behind and less than 1,000 feet below super or heavy aircraft, (b) To small aircraft operating behind and less than 500 feet below B757 aircraft, and (c) To small aircraft following a large aircraft on final approach. 3−2−5 AIM NOTE− 1. Separation and sequencing of VFR aircraft will be suspended in the event of a radar outage as this service is dependent on radar. The pilot will be advised that the service is not available and issued wind, runway information and the time or place to contact the tower. 2. Separation of VFR aircraft will be suspended during CENRAP operations. Traffic advisories and sequencing to the primary airport will be provided on a workload permitting basis. The pilot will be advised when CENRAP is in use. 3. Pilot participation is voluntary within the outer area and can be discontinued, within the outer area, at the pilot’s request. Class C services will be provided in the outer area unless the pilot requests termination of the service. 4. Some facilities provide Class C services only during published hours. At other times, terminal IFR radar service will be provided. It is important to note that the communications and transponder/ADS−B requirements are dependent on the class of airspace established outside of the published hours. f. Secondary Airports 1. In some locations Class C airspace may overlie the Class D surface area of a secondary airport. In order to allow that control tower to provide service to aircraft, portions of the overlapping Class C airspace may be procedurally excluded when the secondary airport tower is in operation. Aircraft operating in these procedurally excluded areas will only be provided airport traffic control services when in communication with the secondary airport tower. 2. Aircraft proceeding inbound to a satellite airport will be terminated at a sufficient distance to allow time to change to the appropriate tower or advisory frequency. Class C services to these aircraft will be discontinued when the aircraft is instructed to contact the tower or change to advisory frequency. 3. Aircraft departing secondary controlled airports will not receive Class C services until they have been radar identified and two-way communications have been established with the Class C airspace facility. 4. This program is not to be interpreted as relieving pilots of their responsibilities to see and avoid other traffic operating in basic VFR weather conditions, to adjust their operations and flight path as necessary to preclude serious wake encounters, to maintain appropriate terrain and obstruction clearance or to remain in weather conditions equal to or 3−2−6 6/17/21 better than the minimums required by 14 CFR Section 91.155. Approach control should be advised and a revised clearance or instruction obtained when compliance with an assigned route, heading and/or altitude is likely to compromise pilot responsibility with respect to terrain and obstruction clearance, vortex exposure, and weather minimums. g. Class C Airspace Areas by State These states currently have designated Class C airspace areas that are depicted on sectional charts. Pilots should consult current sectional charts and NOTAMs for the latest information on services available. Pilots should be aware that some Class C airspace underlies or is adjacent to Class B airspace. (See TBL 3−2−1.) TBL 3−2−1 Class C Airspace Areas by State State/City Airport ALABAMA Birmingham . . . . . . . . . Birmingham−Shuttlesworth International Huntsville . . . . . . . . . . . International−Carl T Jones Fld Mobile . . . . . . . . . . . . . . Regional ALASKA Anchorage . . . . . . . . . . . Ted Stevens International ARIZONA Davis−Monthan . . . . . . . AFB Tucson . . . . . . . . . . . . . . International ARKANSAS Fayetteville (Springdale) Northwest Arkansas Regional Little Rock . . . . . . . . . . Adams Field CALIFORNIA Beale . . . . . . . . . . . . . . . AFB Burbank . . . . . . . . . . . . Bob Hope Fresno . . . . . . . . . . . . . . Yosemite International Monterey . . . . . . . . . . . . Peninsula Oakland . . . . . . . . . . . . . Metropolitan Oakland International Ontario . . . . . . . . . . . . . International Riverside . . . . . . . . . . . . March AFB Sacramento . . . . . . . . . . International San Jose . . . . . . . . . . . . Norman Y. Mineta International Santa Ana . . . . . . . . . . . John Wayne/Orange County Santa Barbara . . . . . . . . Municipal COLORADO Colorado Springs . . . . . Municipal CONNECTICUT Windsor Locks . . . . . . . Bradley International FLORIDA Daytona Beach . . . . . . . International Fort Lauderdale . . . . . . . Hollywood International Fort Myers . . . . . . . . . . SW Florida Regional Jacksonville . . . . . . . . . . International Controlled Airspace 6/17/21 State/City Orlando . . . . . . . . . . . . . Palm Beach . . . . . . . . . . Pensacola . . . . . . . . . . . Pensacola . . . . . . . . . . . Sarasota . . . . . . . . . . . . . Tallahassee . . . . . . . . . . Whiting . . . . . . . . . . . . . GEORGIA Savannah . . . . . . . . . . . . HAWAII Kahului . . . . . . . . . . . . . IDAHO Boise . . . . . . . . . . . . . . . ILLINOIS Champaign . . . . . . . . . . Chicago . . . . . . . . . . . . . Moline . . . . . . . . . . . . . . Peoria . . . . . . . . . . . . . . Springfield . . . . . . . . . . INDIANA Evansville . . . . . . . . . . . Fort Wayne . . . . . . . . . . Indianapolis . . . . . . . . . . South Bend . . . . . . . . . . IOWA Cedar Rapids . . . . . . . . . Des Moines . . . . . . . . . . KANSAS Wichita . . . . . . . . . . . . . KENTUCKY Lexington . . . . . . . . . . . Louisville . . . . . . . . . . . LOUISIANA Baton Rouge . . . . . . . . . Lafayette . . . . . . . . . . . . Shreveport . . . . . . . . . . . Shreveport . . . . . . . . . . . MAINE Bangor . . . . . . . . . . . . . Portland . . . . . . . . . . . . . MICHIGAN Flint . . . . . . . . . . . . . . . . Grand Rapids . . . . . . . . Lansing . . . . . . . . . . . . . MISSISSIPPI Columbus . . . . . . . . . . . Jackson . . . . . . . . . . . . . MISSOURI Springfield . . . . . . . . . . MONTANA Billings . . . . . . . . . . . . . NEBRASKA Lincoln . . . . . . . . . . . . . Omaha . . . . . . . . . . . . . . Controlled Airspace AIM Airport Sanford International International NAS Regional Bradenton International Regional NAS Hilton Head International Kahului Air Terminal Urbana U of Illinois−Willard Midway International Quad City International Greater Peoria Regional Abraham Lincoln Capital Regional International International Regional The Eastern Iowa International Mid−Continent Blue Grass International−Standiford Field Metropolitan, Ryan Field Regional Barksdale AFB Regional International International Jetport Bishop International Gerald R. Ford International Capital City AFB Jackson−Evers International Springfield−Branson National Logan International Lincoln Eppley Airfield State/City Offutt . . . . . . . . . . . . . . . NEVADA Reno . . . . . . . . . . . . . . . NEW HAMPSHIRE Manchester . . . . . . . . . . NEW JERSEY Atlantic City . . . . . . . . . NEW MEXICO Albuquerque . . . . . . . . . NEW YORK Albany . . . . . . . . . . . . . Buffalo . . . . . . . . . . . . . Islip . . . . . . . . . . . . . . . . Rochester . . . . . . . . . . . Syracuse . . . . . . . . . . . . NORTH CAROLINA Asheville . . . . . . . . . . . Fayetteville . . . . . . . . . . Greensboro . . . . . . . . . . Pope . . . . . . . . . . . . . . . Raleigh . . . . . . . . . . . . . OHIO Akron . . . . . . . . . . . . . . Columbus . . . . . . . . . . . Dayton . . . . . . . . . . . . . Toledo . . . . . . . . . . . . . . OKLAHOMA Oklahoma City . . . . . . . Tinker . . . . . . . . . . . . . . Tulsa . . . . . . . . . . . . . . . OREGON Portland . . . . . . . . . . . . . PENNSYLVANIA Allentown . . . . . . . . . . . PUERTO RICO San Juan . . . . . . . . . . . . RHODE ISLAND Providence . . . . . . . . . . SOUTH CAROLINA Charleston . . . . . . . . . . . Columbia . . . . . . . . . . . . Greer . . . . . . . . . . . . . . . Airport AFB Reno/Tahoe International Manchester International International Sunport International Niagara International Long Island MacArthur Greater Rochester International Hancock International Regional Regional/Grannis Field Piedmont Triad International AFB Raleigh−Durham International Akron−Canton Regional Port Columbus International James M. Cox International Express Will Rogers World AFB International International Lehigh Valley International Luis Munoz Marin International Theodore Francis Green State AFB/International Metropolitan Greenville−Spartanburg International Myrtle Beach . . . . . . . . Myrtle Beach International Shaw . . . . . . . . . . . . . . . AFB TENNESSEE Chattanooga . . . . . . . . . Lovell Field Knoxville . . . . . . . . . . . McGhee Tyson Nashville . . . . . . . . . . . . International TEXAS Abilene . . . . . . . . . . . . . Regional Amarillo . . . . . . . . . . . . Rick Husband International Austin . . . . . . . . . . . . . . Austin−Bergstrom International Corpus Christi . . . . . . . . International 3−2−7 AIM State/City Dyess . . . . . . . . . . . . . . El Paso . . . . . . . . . . . . . Harlingen . . . . . . . . . . . Laughlin . . . . . . . . . . . . Lubbock . . . . . . . . . . . . Midland . . . . . . . . . . . . . San Antonio . . . . . . . . . 6/17/21 Airport AFB International Valley International AFB Preston Smith International International International VERMONT Burlington . . . . . . . . . . . International VIRGIN ISLANDS St. Thomas . . . . . . . . . . Charlotte Amalie Cyril E. King VIRGINIA Richmond . . . . . . . . . . . Norfolk . . . . . . . . . . . . . Roanoke . . . . . . . . . . . . WASHINGTON Point Roberts . . . . . . . . Spokane . . . . . . . . . . . . Spokane . . . . . . . . . . . . Whidbey Island . . . . . . . WEST VIRGINIA Charleston . . . . . . . . . . . WISCONSIN Green Bay . . . . . . . . . . . Madison . . . . . . . . . . . . International International Regional/Woodrum Field Vancouver International Fairchild AFB International NAS, Ault Field Yeager Austin Straubel International Dane County Regional−Traux Field Milwaukee . . . . . . . . . . General Mitchell International 3−2−5. Class D Airspace a. Definition. Generally, Class D airspace extends upward from the surface to 2,500 feet above the airport elevation (charted in MSL) surrounding those airports that have an operational control tower. The configuration of each Class D airspace area is individually tailored and when instrument procedures are published, the airspace will normally be designed to contain the procedures. 1. Class D surface areas may be designated as full-time (24 hour tower operations) or part-time. Part-time Class D effective times are published in the Chart Supplement U.S. 2. Where a Class D surface area is part-time, the airspace may revert to either a Class E surface area (see paragraph 3−2−6e1) or Class G airspace. When a part–time Class D surface area changes to Class G, the surface area becomes Class G airspace up to, but not including, the overlying controlled airspace. NOTE− 1. The airport listing in the Chart Supplement U.S. will 3−2−8 state the part–time surface area status (for example, “other times CLASS E” or “other times CLASS G”). 2. Normally, the overlying controlled airspace is the Class E transition area airspace that begins at either 700 feet AGL (charted as magenta vignette) or 1200 feet AGL (charted as blue vignette). This may be determined by consulting the applicable VFR Sectional or Terminal Area Charts. b. Operating Rules and Pilot/Equipment Requirements: 1. Pilot Certification. No specific certification required. 2. Equipment. Unless otherwise authorized by ATC, an operable two−way radio is required. 3. Arrival or Through Flight Entry Requirements. Two−way radio communication must be established with the ATC facility providing ATC services prior to entry and thereafter maintain those communications while in the Class D airspace. Pilots of arriving aircraft should contact the control tower on the publicized frequency and give their position, altitude, destination, and any request(s). Radio contact should be initiated far enough from the Class D airspace boundary to preclude entering the Class D airspace before two−way radio communications are established. NOTE− 1. If the controller responds to a radio call with, “[aircraft callsign] standby,” radio communications have been established and the pilot can enter the Class D airspace. 2. If workload or traffic conditions prevent immediate entry into Class D airspace, the controller will inform the pilot to remain outside the Class D airspace until conditions permit entry. EXAMPLE− 1. “[Aircraft callsign] remain outside the Class Delta airspace and standby.” It is important to understand that if the controller responds to the initial radio call without using the aircraft callsign, radio communications have not been established and the pilot may not enter the Class D airspace. 2. “Aircraft calling Manassas tower standby.” At those airports where the control tower does not operate 24 hours a day, the operating hours of the tower will be listed on the appropriate charts and in the Chart Supplement U.S. During the hours the tower is not in operation, the Class E surface area rules or a combination of Class E rules to 700 feet above ground level and Class G rules to the surface will become applicable. Check the Chart Supplement U.S. for specifics. Controlled Airspace 6/17/21 4. Departures from: (a) A primary or satellite airport with an operating control tower. Two-way radio communications must be established and maintained with the control tower, and thereafter as instructed by ATC while operating in the Class D airspace. (b) A satellite airport without an operating control tower. Two-way radio communications must be established as soon as practicable after departing with the ATC facility having jurisdiction over the Class D airspace as soon as practicable after departing. 5. Aircraft Speed. Unless otherwise authorized or required by ATC, no person may operate an aircraft at or below 2,500 feet above the surface within 4 nautical miles of the primary airport of a Class D airspace area at an indicated airspeed of more than 200 knots (230 mph). c. Class D airspace areas are depicted on Sectional and Terminal charts with blue segmented lines, and on IFR En Route Lows with a boxed [D]. d. Surface area arrival extensions: 1. Class D surface area arrival extensions for instrument approach procedures may be Class D or Class E airspace. As a general rule, if all extensions are 2 miles or less, they remain part of the Class D surface area. However, if any one extension is greater than 2 miles, then all extensions will be Class E airspace. 2. Surface area arrival extensions are effective during the published times of the surface area. For part–time Class D surface areas that revert to Class E airspace, the arrival extensions will remain in effect as Class E airspace. For part–time Class D surface areas that change to Class G airspace, the arrival extensions will become Class G at the same time. e. Separation for VFR Aircraft. No separation services are provided to VFR aircraft. 3−2−6. Class E Airspace a. Definition. Class E airspace is controlled airspace that is designated to serve a variety of terminal or en route purposes as described in this paragraph. b. Operating Rules and Pilot/Equipment Requirements: Controlled Airspace AIM 1. Pilot Certification. No specific certification required. 2. Equipment. Unless otherwise authorized by ATC: (a) An operable radar beacon transponder with automatic altitude reporting capability and operable ADS−B Out equipment are required at and above 10,000 feet MSL within the 48 contiguous states and the District of Columbia, excluding the airspace at and below 2,500 feet above the surface, and (b) Operable ADS−B Out equipment at and above 3,000 feet MSL over the Gulf of Mexico from the coastline of the United States out to 12 nautical miles. NOTE− The airspace described in (b) is specified in 14 CFR § 91.225 for ADS−B Out requirements. However, 14 CFR § 91.215 does not include this airspace for transponder requirements. 3. Arrival or Through Flight Entry Requirements. No specific requirements. c. Charts. Class E airspace below 14,500 feet MSL is charted on Sectional, Terminal, and IFR Enroute Low Altitude charts. d. Vertical limits. Except where designated at a lower altitude (see paragraph 3−2−6e, below, for specifics), Class E airspace in the United States consists of: 1. The airspace extending upward from 14,500 feet MSL to, but not including, 18,000 feet MSL overlying the 48 contiguous states, the District of Columbia and Alaska, including the waters within nautical 12 miles from the coast of the 48 contiguous states and Alaska; excluding: (a) The Alaska peninsula west of longitude 16000'00''W.; and (b) The airspace below 1,500 feet above the surface of the earth unless specifically designated lower (for example, in mountainous terrain higher than 13,000 feet MSL). 2. The airspace above FL 600 is Class E airspace. e. Functions of Class E Airspace. Class E airspace may be designated for the following purposes: 3−2−9 AIM 6/17/21 1. Surface area designated for an airport where a control tower is not in operation. Class E surface areas extend upward from the surface to a designated altitude, or to the adjacent or overlying controlled airspace. The airspace will be configured to contain all instrument procedures. and are designated for airports with an approved instrument procedure. (a) To qualify for a Class E surface area, the airport must have weather observation and reporting capability, and communications capability must exist with aircraft down to the runway surface. NOTE− Do not confuse the 700-foot and 1200-foot Class E transition areas with surface areas or surface area extensions. (b) A Class E surface area may also be designated to accommodate part-time operations at a Class C or Class D airspace location (for example, those periods when the control tower is not in operation). (c) Pilots should refer to the airport page in the applicable Chart Supplement U.S. for surface area status information. 2. Extension to a surface area. Class E airspace may be designated as extensions to Class B, Class C, Class D, and Class E surface areas. Class E airspace extensions begin at the surface and extend up to the overlying controlled airspace. The extensions provide controlled airspace to contain standard instrument approach procedures without imposing a communications requirement on pilots operating under VFR. Surface area arrival extensions become part of the surface area and are in effect during the same times as the surface area. NOTE− When a Class C or Class D surface area is not in effect continuously (for example, where a control tower only operates part-time), the surface area airspace will change to either a Class E surface area or Class G airspace. In such cases, the “Airspace” entry for the airport in the Chart Supplement U.S. will state “other times Class E” or “other times Class G.” When a part-time surface area changes to Class E airspace, the Class E arrival extensions will remain in effect as Class E airspace. If a part–time Class C, Class D, or Class E surface area becomes Class G airspace, the arrival extensions will change to Class G at the same time. 3. Airspace used for transition. Class E airspace areas may be designated for transitioning aircraft to/from the terminal or en route environment. (a) Class E transition areas extend upward from either 700 feet AGL (shown as magenta vignette on sectional charts) or 1,200 feet AGL (blue vignette) 3−2−10 (b) The 700-foot/1200-foot AGL Class E airspace transition areas remain in effect continuously, regardless of airport operating hours or surface area status. 4. En Route Domestic Areas. There are Class E airspace areas that extend upward from a specified altitude and are en route domestic airspace areas that provide controlled airspace in those areas where there is a requirement to provide IFR en route ATC services but the Federal airway system is inadequate. 5. Federal Airways and Low-Altitude RNAV Routes. Federal airways and low-altitude RNAV routes are Class E airspace areas and, unless otherwise specified, extend upward from 1,200 feet AGL to, but not including,18,000 feet MSL. (a) Federal airways consist of Low/Medium Frequency (L/MF) airways (colored Federal airways) and VOR Federal airways. (1) L/MF airways are based on non−directional beacons (NDB) and are identified as green, red, amber, or blue. (2) VOR Federal airways are based on VOR/VORTAC facilities and are identified by a “V” prefix. (b) Low-altitude RNAV routes consist of T-routes and helicopter RNAV routes (TK-routes). NOTE− See AIM Paragraph 5-3-4, Airways and Route Systems, for more details and charting information. 6. Offshore Airspace Areas. There are Class E airspace areas that extend upward from a specified altitude to, but not including, 18,000 feet MSL and are designated as offshore airspace areas. These areas provide controlled airspace beyond 12 miles from the coast of the U.S. in those areas where there is a requirement to provide IFR en route ATC services and within which the U.S. is applying domestic procedures. f. Separation for VFR Aircraft. No separation services are provided to VFR aircraft. Controlled Airspace 6/17/21 AIM Section 3. Class G Airspace 3−3−1. General 3−3−3. IFR Requirements Class G airspace (uncontrolled) is that portion of airspace that has not been designated as Class A, Class B, Class C, Class D, or Class E airspace. 3−3−2. VFR Requirements Rules governing VFR flight have been adopted to assist the pilot in meeting the responsibility to see and avoid other aircraft. Minimum flight visibility and distance from clouds required for VFR flight are contained in 14 CFR Section 91.155. (See TBL 3−1−1.) a. Title 14 CFR specifies the pilot and aircraft equipment requirements for IFR flight. Pilots are reminded that in addition to altitude or flight level requirements, 14 CFR Section 91.177 includes a requirement to remain at least 1,000 feet (2,000 feet in designated mountainous terrain) above the highest obstacle within a horizontal distance of 4 nautical miles from the course to be flown. b. IFR Altitudes. (See TBL 3−3−1.) TBL 3−3−1 IFR Altitudes Class G Airspace If your magnetic course (ground track) is: 0 to 179 180 to 359 Class G Airspace And you are below 18,000 feet MSL, fly: Odd thousands MSL, (3,000; 5,000; 7,000, etc.) Even thousands MSL, (2,000; 4,000; 6,000, etc.) 3−3−1 12/2/21 6/17/21 AIM Section 4. Special Use Airspace 3−4−1. General 3−4−3. Restricted Areas a. Special use airspace (SUA) consists of that airspace wherein activities must be confined because of their nature, or wherein limitations are imposed upon aircraft operations that are not a part of those activities, or both. SUA areas are depicted on aeronautical charts, except for controlled firing areas (CFA), temporary military operations areas (MOA), and temporary restricted areas. a. Restricted areas contain airspace identified by an area on the surface of the earth within which the flight of aircraft, while not wholly prohibited, is subject to restrictions. Activities within these areas must be confined because of their nature or limitations imposed upon aircraft operations that are not a part of those activities or both. Restricted areas denote the existence of unusual, often invisible, hazards to aircraft such as artillery firing, aerial gunnery, or guided missiles. Penetration of restricted areas without authorization from the using or controlling agency may be extremely hazardous to the aircraft and its occupants. Restricted areas are published in the Federal Register and constitute 14 CFR Part 73. b. Prohibited and restricted areas are regulatory special use airspace and are established in 14 CFR Part 73 through the rulemaking process. c. Warning areas, MOAs, alert areas, CFAs, and national security areas (NSA) are nonregulatory special use airspace. d. Special use airspace descriptions (except CFAs) are contained in FAA Order JO 7400.10, Special Use Airspace. e. Permanent SUA (except CFAs) is charted on Sectional Aeronautical, VFR Terminal Area, and applicable En Route charts, and include the hours of operation, altitudes, and the controlling agency. NOTE− For temporary restricted areas and temporary MOAs, pilots should review the Domestic Notices found on the Federal NOTAM System (FNS) NOTAM Search website under External Links or the Air Traffic Plans and Publications website, the FAA SUA website, and/or contact the appropriate overlying ATC facility to determine the effect of non−depicted SUA areas along their routes of flight. 3−4−2. Prohibited Areas Prohibited areas contain airspace of defined dimensions identified by an area on the surface of the earth within which the flight of aircraft is prohibited. Such areas are established for security or other reasons associated with the national welfare. These areas are published in the Federal Register and are depicted on aeronautical charts. Special Use Airspace b. ATC facilities apply the following procedures when aircraft are operating on an IFR clearance (including those cleared by ATC to maintain VFR-on-top) via a route which lies within joint-use restricted airspace. 1. If the restricted area is not active and has been released to the controlling agency (FAA), the ATC facility will allow the aircraft to operate in the restricted airspace without issuing specific clearance for it to do so. 2. If the restricted area is active and has not been released to the controlling agency (FAA), the ATC facility will issue a clearance which will ensure the aircraft avoids the restricted airspace unless it is on an approved altitude reservation mission or has obtained its own permission to operate in the airspace and so informs the controlling facility. NOTE− The above apply only to joint-use restricted airspace and not to prohibited and nonjoint-use airspace. For the latter categories, the ATC facility will issue a clearance so the aircraft will avoid the restricted airspace unless it is on an approved altitude reservation mission or has obtained its own permission to operate in the airspace and so informs the controlling facility. c. Permanent restricted areas are charted on Sectional Aeronautical, VFR Terminal Area, and the appropriate En Route charts. 3−4−1 AIM NOTE− Temporary restricted areas are not charted. 3−4−4. Warning Areas A warning area is airspace of defined dimensions, extending from three nautical miles outward from the coast of the U.S., that contains activity that may be hazardous to nonparticipating aircraft. The purpose of such warning areas is to warn nonparticipating pilots of the potential danger. A warning area may be located over domestic or international waters or both. 3−4−5. Military Operations Areas a. MOAs consist of airspace of defined vertical and lateral limits established for the purpose of separating certain military training activities from IFR traffic. Whenever a MOA is being used, nonparticipating IFR traffic may be cleared through a MOA if IFR separation can be provided by ATC. Otherwise, ATC will reroute or restrict nonparticipating IFR traffic. b. Examples of activities conducted in MOAs include, but are not limited to: air combat tactics, air intercepts, aerobatics, formation training, and low−altitude tactics. Military pilots flying in an active MOA are exempted from the provisions of 14 CFR Section 91.303(c) and (d) which prohibits aerobatic flight within Class D and Class E surface areas, and within Federal airways. Additionally, the Department of Defense has been issued an authorization to operate aircraft at indicated airspeeds in excess of 250 knots below 10,000 feet MSL within active MOAs. c. Pilots operating under VFR should exercise extreme caution while flying within a MOA when military activity is being conducted. The activity status (active/inactive) of MOAs may change frequently. Therefore, pilots should contact any FSS within 100 miles of the area to obtain accurate real-time information concerning the MOA hours of operation. Prior to entering an active MOA, pilots should contact the controlling agency for traffic advisories. d. Permanent MOAs are charted on Sectional Aeronautical, VFR Terminal Area, and the appropriate En Route Low Altitude charts. NOTE− Temporary MOAs are not charted. 3−4−2 6/17/21 3−4−6. Alert Areas Alert areas are depicted on aeronautical charts to inform nonparticipating pilots of areas that may contain a high volume of pilot training or an unusual type of aerial activity. Pilots should be particularly alert when flying in these areas. All activity within an alert area must be conducted in accordance with CFRs, without waiver, and pilots of participating aircraft as well as pilots transiting the area must be equally responsible for collision avoidance. 3−4−7. Controlled Firing Areas CFAs contain activities which, if not conducted in a controlled environment, could be hazardous to nonparticipating aircraft. The distinguishing feature of the CFA, as compared to other special use airspace, is that its activities are suspended immediately when spotter aircraft, radar, or ground lookout positions indicate an aircraft might be approaching the area. There is no need to chart CFAs since they do not cause a nonparticipating aircraft to change its flight path. 3−4−8. National Security Areas NSAs consist of airspace of defined vertical and lateral dimensions established at locations where there is a requirement for increased security and safety of ground facilities. Pilots are requested to voluntarily avoid flying through the depicted NSA. When it is necessary to provide a greater level of security and safety, flight in NSAs may be temporarily prohibited by regulation under the provisions of 14 CFR Section 99.7. Regulatory prohibitions will be issued by System Operations Security and disseminated via NOTAM. Inquiries about NSAs should be directed to System Operations Security. REFERENCE− AIM, Para 5−6−1, National Security 3−4−9. Obtaining Special Use Airspace Status a. Pilots can request the status of SUA by contacting the using or controlling agency. The frequency for the controlling agency is tabulated in the margins of the applicable IFR and VFR charts. b. An airspace NOTAM will be issued for SUA when the SUA airspace (permanent and/or temporary) requires a NOTAM for activation. Pilots should check ARTCC NOTAMs for airspace activation. Special Use Airspace 6/17/21 c. Special Use Airspace Information Service (SUAIS) (Alaska Only). The SUAIS is a 24−hour service operated by the military that provides civilian pilots, flying VFR, with information regarding military flight operations in certain MOAs and restricted airspace within central Alaska. The service provides “near real time” information on military flight activity in the interior Alaska MOA and Restricted Area complex. SUAIS also provides Special Use Airspace AIM information on artillery firing, known helicopter operations, and unmanned aerial vehicle operations. Pilots flying VFR are encouraged to use SUAIS. See the Alaska Chart Supplement for hours of operation, phone numbers, and radio frequencies. d. Special use airspace scheduling data for preflight planning is available via the FAA SUA website. 3−4−3 6/17/21 AIM Section 5. Other Airspace Areas 3−5−1. Airport Advisory/Information Services REFERENCE− AIM, Paragraph 4−1−9 , Traffic Advisory Practices at Airports Without Operating Control Towers a. There are two advisory type services available at selected airports. b. It is not mandatory that pilots participate in the Airport Advisory programs. Participation enhances safety for everyone operating around busy GA airports; therefore, everyone is encouraged to participate and provide feedback that will help improve the program. 1. Local Airport Advisory (LAA) service is available only in Alaska and is operated within 10 statute miles of an airport where a control tower is not operating but where a FSS is located on the airport. At such locations, the FSS provides a complete local airport advisory service to arriving and departing aircraft. During periods of fast changing weather the FSS will automatically provide Final Guard as part of the service from the time the aircraft reports “on−final” or “taking−the−active−runway” until the aircraft reports “on−the−ground” or “airborne.” NOTE− Current policy, when requesting remote ATC services, requires that a pilot monitor the automated weather broadcast at the landing airport prior to requesting ATC services. The FSS automatically provides Final Guard, when appropriate, during LAA/Remote Airport Advisory (RAA) operations. Final Guard is a value added wind/altimeter monitoring service, which provides an automatic wind and altimeter check during active weather situations when the pilot reports on−final or taking the active runway. During the landing or take−off operation when the winds or altimeter are actively changing the FSS will blind broadcast significant changes when the specialist believes the change might affect the operation. Pilots should acknowledge the first wind/altimeter check but due to cockpit activity no acknowledgement is expected for the blind broadcasts. It is prudent for a pilot to report on−the−ground or airborne to end the service. 2. Remote Airport Information Service (RAIS) is provided in support of short term special events like small to medium fly−ins. The service is advertised by NOTAM D only. The FSS will not have access to a continuous readout of the current winds and altimeter; therefore, RAIS does not include weather and/or Final Guard service. However, known traffic, special event instructions, and all other services are provided. NOTE− The airport authority and/or manager should request RAIS support on official letterhead directly with the manager of the FSS that will provide the service at least 60 days in advance. Approval authority rests with the FSS manager and is based on workload and resource availability. Other Airspace Areas 3−5−2. Military Training Routes a. National security depends largely on the deterrent effect of our airborne military forces. To be proficient, the military services must train in a wide range of airborne tactics. One phase of this training involves “low level” combat tactics. The required maneuvers and high speeds are such that they may occasionally make the see-and-avoid aspect of VFR flight more difficult without increased vigilance in areas containing such operations. In an effort to ensure the greatest practical level of safety for all flight operations, the Military Training Route (MTR) program was conceived. b. The MTR program is a joint venture by the FAA and the Department of Defense (DOD). MTRs are mutually developed for use by the military for the purpose of conducting low-altitude, high-speed training. The routes above 1,500 feet AGL are developed to be flown, to the maximum extent possible, under IFR. The routes at 1,500 feet AGL and below are generally developed to be flown under VFR. c. Generally, MTRs are established below 10,000 feet MSL for operations at speeds in excess of 250 knots. However, route segments may be defined at higher altitudes for purposes of route continuity. For example, route segments may be defined for descent, climbout, and mountainous terrain. There are IFR and VFR routes as follows: 1. IFR Military Training Routes−(IR). Operations on these routes are conducted in accordance with IFR regardless of weather conditions. 2. VFR Military Training Routes−(VR). Operations on these routes are conducted in accordance with VFR except flight visibility must be 3−5−1 AIM 6/17/21 5 miles or more; and flights must not be conducted below a ceiling of less than 3,000 feet AGL. d. Military training routes will be identified and charted as follows: 1. Route identification. (a) MTRs with no segment above 1,500 feet AGL must be identified by four number characters; e.g., IR1206, VR1207. (b) MTRs that include one or more segments above 1,500 feet AGL must be identified by three number characters; e.g., IR206, VR207. (c) Alternate IR/VR routes or route segments are identified by using the basic/principal route designation followed by a letter suffix, e.g., IR008A, VR1007B, etc. 2. Route charting. (a) IFR Enroute Low Altitude Chart. This chart will depict all IR routes and all VR routes that accommodate operations above 1,500 feet AGL. (b) VFR Sectional Aeronautical Charts. These charts will depict military training activities such as IR and VR information. (c) Area Planning (AP/1B) Chart (DOD Flight Information Publication−FLIP). This chart is published by the National Geospatial−Intelligence Agency (NGA) primarily for military users and contains detailed information on both IR and VR routes. REFERENCE− AIM, Paragraph 9−1−5 , Subparagraph a, National Geospatial−Intelligence Agency (NGA) Products e. The FLIP contains charts and narrative descriptions of these routes. To obtain this publication contact: Defense Logistics Agency for Aviation Mapping Customer Operations (DLA AVN/QAM) 8000 Jefferson Davis Highway Richmond, VA 23297−5339 Toll free phone: 1−800−826−0342 Commercial: 804−279−6500 This NGA FLIP is available for pilot briefings at FSS and many airports. f. Nonparticipating aircraft are not prohibited from flying within an MTR; however, extreme vigilance should be exercised when conducting flight 3−5−2 through or near these routes. Pilots should contact FSSs within 100 NM of a particular MTR to obtain current information or route usage in their vicinity. Information available includes times of scheduled activity, altitudes in use on each route segment, and actual route width. Route width varies for each MTR and can extend several miles on either side of the charted MTR centerline. Route width information for IR and VR MTRs is also available in the FLIP AP/1B along with additional MTR (slow routes/air refueling routes) information. When requesting MTR information, pilots should give the FSS their position, route of flight, and destination in order to reduce frequency congestion and permit the FSS specialist to identify the MTR which could be a factor. 3−5−3. Temporary Flight Restrictions a. General. This paragraph describes the types of conditions under which the FAA may impose temporary flight restrictions. It also explains which FAA elements have been delegated authority to issue a temporary flight restrictions NOTAM and lists the types of responsible agencies/offices from which the FAA will accept requests to establish temporary flight restrictions. The 14 CFR is explicit as to what operations are prohibited, restricted, or allowed in a temporary flight restrictions area. Pilots are responsible to comply with 14 CFR Sections 91.137, 91.138, 91.141 and 91.143 when conducting flight in an area where a temporary flight restrictions area is in effect, and should check appropriate NOTAMs during flight planning. b. The purpose for establishing a temporary flight restrictions area is to: 1. Protect persons and property in the air or on the surface from an existing or imminent hazard associated with an incident on the surface when the presence of low flying aircraft would magnify, alter, spread, or compound that hazard (14 CFR Section 91.137(a)(1)); 2. Provide a safe environment for the operation of disaster relief aircraft (14 CFR Section 91.137(a)(2)); or 3. Prevent an unsafe congestion of sightseeing aircraft above an incident or event which may generate a high degree of public interest (14 CFR Section 91.137(a)(3)). Other Airspace Areas 6/17/21 4. Protect declared national disasters for humanitarian reasons in the State of Hawaii (14 CFR Section 91.138). 5. Protect the President, Vice President, or other public figures (14 CFR Section 91.141). 6. Provide a safe environment for space agency operations (14 CFR Section 91.143). c. Except for hijacking situations, when the provisions of 14 CFR Section 91.137(a)(1) or (a)(2) are necessary, a temporary flight restrictions area will only be established by or through the area manager at the Air Route Traffic Control Center (ARTCC) having jurisdiction over the area concerned. A temporary flight restrictions NOTAM involving the conditions of 14 CFR Section 91.137(a)(3) will be issued at the direction of the service area office director having oversight of the airspace concerned. When hijacking situations are involved, a temporary flight restrictions area will be implemented through the TSA Aviation Command Center. The appropriate FAA air traffic element, upon receipt of such a request, will establish a temporary flight restrictions area under 14 CFR Section 91.137(a)(1). d. The FAA accepts recommendations for the establishment of a temporary flight restrictions area under 14 CFR Section 91.137(a)(1) from military major command headquarters, regional directors of the Office of Emergency Planning, Civil Defense State Directors, State Governors, or other similar authority. For the situations involving 14 CFR Section 91.137(a)(2), the FAA accepts recommendations from military commanders serving as regional, subregional, or Search and Rescue (SAR) coordinators; by military commanders directing or coordinating air operations associated with disaster relief; or by civil authorities directing or coordinating organized relief air operations (includes representatives of the Office of Emergency Planning, U.S. Forest Service, and State aeronautical agencies). Appropriate authorities for a temporary flight restrictions establishment under 14 CFR Section 91.137(a)(3) are any of those listed above or by State, county, or city government entities. e. The type of restrictions issued will be kept to a minimum by the FAA consistent with achievement of the necessary objective. Situations which warrant the extreme restrictions of 14 CFR Section 91.137(a)(1) include, but are not limited to: toxic gas leaks or Other Airspace Areas AIM spills, flammable agents, or fumes which if fanned by rotor or propeller wash could endanger persons or property on the surface, or if entered by an aircraft could endanger persons or property in the air; imminent volcano eruptions which could endanger airborne aircraft and occupants; nuclear accident or incident; and hijackings. Situations which warrant the restrictions associated with 14 CFR Section 91.137(a)(2) include: forest fires which are being fought by releasing fire retardants from aircraft; and aircraft relief activities following a disaster (earthquake, tidal wave, flood, etc.). 14 CFR Section 91.137(a)(3) restrictions are established for events and incidents that would attract an unsafe congestion of sightseeing aircraft. f. The amount of airspace needed to protect persons and property or provide a safe environment for rescue/relief aircraft operations is normally limited to within 2,000 feet above the surface and within a 3−nautical−mile radius. Incidents occurring within Class B, Class C, or Class D airspace will normally be handled through existing procedures and should not require the issuance of a temporary flight restrictions NOTAM. Temporary flight restrictions affecting airspace outside of the U.S. and its territories and possessions are issued with verbiage excluding that airspace outside of the 12−mile coastal limits. g. The FSS nearest the incident site is normally the “coordination facility.” When FAA communications assistance is required, the designated FSS will function as the primary communications facility for coordination between emergency control authorities and affected aircraft. The ARTCC may act as liaison for the emergency control authorities if adequate communications cannot be established between the designated FSS and the relief organization. For example, the coordination facility may relay authorizations from the on-scene emergency response official in cases where news media aircraft operations are approved at the altitudes used by relief aircraft. h. ATC may authorize operations in a temporary flight restrictions area under its own authority only when flight restrictions are established under 14 CFR Section 91.137(a)(2) and (a)(3). The appropriate ARTCC/airport traffic control tower manager will, however, ensure that such authorized flights do not hamper activities or interfere with the event for which restrictions were implemented. However, ATC will 3−5−3 AIM not authorize local IFR flights into the temporary flight restrictions area. i. To preclude misunderstanding, the implementing NOTAM will contain specific and formatted information. The facility establishing a temporary flight restrictions area will format a NOTAM beginning with the phrase “FLIGHT RESTRICTIONS” followed by: the location of the temporary flight restrictions area; the effective period; the area defined in statute miles; the altitudes affected; the FAA coordination facility and commercial telephone number; the reason for the temporary flight restrictions; the agency directing any relief activities and its commercial telephone number; and other information considered appropriate by the issuing authority. EXAMPLE− 1. 14 CFR Section 91.137(a)(1): The following NOTAM prohibits all aircraft operations except those specified in the NOTAM. Flight restrictions Matthews, Virginia, effective immediately until 9610211200. Pursuant to 14 CFR Section 91.137(a)(1) temporary flight restrictions are in effect. Rescue operations in progress. Only relief aircraft operations under the direction of the Department of Defense are authorized in the airspace at and below 5,000 feet MSL within a 2−nautical−mile radius of Laser AFB, Matthews, Virginia. Commander, Laser AFB, in charge (897) 946−5543 (122.4). Steenson FSS (792) 555−6141 (123.1) is the FAA coordination facility. 2. 14 CFR Section 91.137(a)(2): The following NOTAM permits flight operations in accordance with 14 CFR Section 91.137(a)(2). The on-site emergency response official to authorize media aircraft operations below the altitudes used by the relief aircraft. Flight restrictions 25 miles east of Bransome, Idaho, effective immediately until 9601202359 UTC. Pursuant to 14 CFR Section 91.137(a)(2) temporary flight restrictions are in effect within a 4−nautical−mile radius of the intersection of county roads 564 and 315 at and below 3,500 feet MSL to provide a safe environment for fire fighting aircraft operations. Davis County sheriff ’s department (792) 555−8122 (122.9) is in charge of on-scene emergency response activities. Glivings FSS (792) 555−1618 (122.2) is the FAA coordination facility. 3. 14 CFR Section 91.137(a)(3): The following NOTAM prohibits sightseeing aircraft operations. Flight restrictions Brown, Tennessee, due to olympic activity. Effective 9606181100 UTC until 9607190200 3−5−4 6/17/21 UTC. Pursuant to 14 CFR Section 91.137(a)(3) temporary flight restrictions are in effect within a 3−nautical−mile radius of N355783/W835242 and Volunteer VORTAC 019 degree radial 3.7 DME fix at and below 2,500 feet MSL. Norton FSS (423) 555−6742 (126.6) is the FAA coordination facility. 4. 14 CFR Section 91.138: The following NOTAM prohibits all aircraft except those operating under the authorization of the official in charge of associated emergency or disaster relief response activities, aircraft carrying law enforcement officials, aircraft carrying personnel involved in an emergency or legitimate scientific purposes, carrying properly accredited news media, and aircraft operating in accordance with an ATC clearance or instruction. Flight restrictions Kapalua, Hawaii, effective 9605101200 UTC until 9605151500 UTC. Pursuant to 14 CFR Section 91.138 temporary flight restrictions are in effect within a 3−nautical−mile radius of N205778/W1564038 and Maui/OGG/VORTAC 275 degree radial at 14.1 nautical miles. John Doe 808−757−4469 or 122.4 is in charge of the operation. Honolulu/HNL 808−757−4470 (123.6) FSS is the FAA coordination facility. 5. 14 CFR Section 91.141: The following NOTAM prohibits all aircraft. Flight restrictions Stillwater, Oklahoma, June 21, 1996. Pursuant to 14 CFR Section 91.141 aircraft flight operations are prohibited within a 3−nautical−mile radius, below 2000 feet AGL of N360962/W970515 and the Stillwater/SWO/VOR/DME 176 degree radial 3.8−nautical−mile fix from 1400 local time to 1700 local time June 21, 1996, unless otherwise authorized by ATC. 6. 14 CFR Section 91.143: The following NOTAM prohibits any aircraft of U.S. registry, or pilot any aircraft under the authority of an airman certificate issued by the FAA. Kennedy space center space operations area effective immediately until 9610152100 UTC. Pursuant to 14 CFR Section 91.143, flight operations conducted by FAA certificated pilots or conducted in aircraft of U.S. registry are prohibited at any altitude from surface to unlimited, within the following area 30−nautical−mile radius of the Melbourne/MLB/VORTAC 010 degree radial 21−nautical−mile fix. St. Petersburg, Florida/PIE/FSS 813−545−1645 (122.2) is the FAA coordination facility and should be contacted for the current status of any airspace associated with the space shuttle operations. This airspace encompasses R2933, R2932, R2931, R2934, R2935, W497A and W158A. Additional warning and restricted areas will be active in conjunction with the operations. Pilots must consult all NOTAMs regarding this operation. Other Airspace Areas 6/17/21 3−5−4. Parachute Jump Aircraft Operations a. Procedures relating to parachute jump areas are contained in 14 CFR Part 105. Tabulations of parachute jump areas in the U.S. are contained in the Chart Supplement U.S. b. Pilots of aircraft engaged in parachute jump operations are reminded that all reported altitudes must be with reference to mean sea level, or flight level, as appropriate, to enable ATC to provide meaningful traffic information. c. Parachute operations in the vicinity of an airport without an operating control tower − there is no substitute for alertness while in the vicinity of an airport. It is essential that pilots conducting parachute operations be alert, look for other traffic, and exchange traffic information as recommended in Paragraph 4−1−9, Traffic Advisory Practices at Airports Without Operating Control Towers. In addition, pilots should avoid releasing parachutes while in an airport traffic pattern when there are other aircraft in that pattern. Pilots should make appropriate broadcasts on the designated Common Traffic Advisory Frequency (CTAF), and monitor that CTAF until all parachute activity has terminated or the aircraft has left the area. Prior to commencing a jump operation, the pilot should broadcast the Other Airspace Areas AIM aircraft’s altitude and position in relation to the airport, the approximate relative time when the jump will commence and terminate, and listen to the position reports of other aircraft in the area. 3−5−5. Published VFR Routes Published VFR routes for transitioning around, under and through complex airspace such as Class B airspace were developed through a number of FAA and industry initiatives. All of the following terms, i.e., “VFR Flyway” “VFR Corridor” and “Class B Airspace VFR Transition Route” have been used when referring to the same or different types of routes or airspace. The following paragraphs identify and clarify the functionality of each type of route, and specify where and when an ATC clearance is required. a. VFR Flyways. 1. VFR Flyways and their associated Flyway Planning Charts were developed from the recommendations of a National Airspace Review Task Group. A VFR Flyway is defined as a general flight path not defined as a specific course, for use by pilots in planning flights into, out of, through or near complex terminal airspace to avoid Class B airspace. An ATC clearance is NOT required to fly these routes. 3−5−5 AIM 6/17/21 FIG 3−5−1 VFR Flyway Planning Chart 3−5−6 Other Airspace Areas 6/17/21 2. VFR Flyways are depicted on the reverse side of some of the VFR Terminal Area Charts (TAC), commonly referred to as Class B airspace charts. (See FIG 3−5−1.) Eventually all TACs will include a VFR Flyway Planning Chart. These charts identify VFR flyways designed to help VFR pilots avoid major controlled traffic flows. They may further depict multiple VFR routings throughout the area which may be used as an alternative to flight within Class B airspace. The ground references provide a guide for improved visual navigation. These routes are not intended to discourage requests for VFR operations within Class B airspace but are designed solely to assist pilots in planning for flights under and around busy Class B airspace without actually entering Class B airspace. 3. It is very important to remember that these suggested routes are not sterile of other traffic. The entire Class B airspace, and the airspace underneath it, may be heavily congested with many different types of aircraft. Pilot adherence to VFR rules must be exercised at all times. Further, when operating beneath Class B airspace, communications must be established and maintained between your aircraft and any control tower while transiting the Class B, Class C, and Class D surface areas of those airports under Class B airspace. b. VFR Corridors. 1. The design of a few of the first Class B airspace areas provided a corridor for the passage of uncontrolled traffic. A VFR corridor is defined as airspace through Class B airspace, with defined vertical and lateral boundaries, in which aircraft may operate without an ATC clearance or communication with air traffic control. 2. These corridors are, in effect, a “hole” through Class B airspace. (See FIG 3−5−2.) A classic example would be the corridor through the Los Angeles Class B airspace, which has been subsequently changed to Special Flight Rules airspace (SFR). A corridor is surrounded on all sides by Class B airspace and does not extend down to the surface like a VFR Flyway. Because of their finite lateral and vertical limits, and the volume of VFR Other Airspace Areas AIM traffic using a corridor, extreme caution and vigilance must be exercised. FIG 3−5−2 Class B Airspace 3. Because of the heavy traffic volume and the procedures necessary to efficiently manage the flow of traffic, it has not been possible to incorporate VFR corridors in the development or modifications of Class B airspace in recent years. c. Class B Airspace VFR Transition Routes. 1. To accommodate VFR traffic through certain Class B airspace, such as Seattle, Phoenix and Los Angeles, Class B Airspace VFR Transition Routes were developed. A Class B Airspace VFR Transition Route is defined as a specific flight course depicted on a TAC for transiting a specific Class B airspace. These routes include specific ATC-assigned altitudes, and pilots must obtain an ATC clearance prior to entering Class B airspace on the route. 2. These routes, as depicted in FIG 3−5−3, are designed to show the pilot where to position the aircraft outside of, or clear of, the Class B airspace where an ATC clearance can normally be expected with minimal or no delay. Until ATC authorization is received, pilots must remain clear of Class B airspace. On initial contact, pilots should advise ATC of their position, altitude, route name desired, and direction of flight. After a clearance is received, pilots must fly the route as depicted and, most importantly, adhere to ATC instructions. 3−5−7 AIM 6/17/21 FIG 3−5−3 VFR Transition Route 3−5−8 Other Airspace Areas 6/17/21 3−5−6. Terminal Radar Service Area (TRSA) a. Background. TRSAs were originally established as part of the Terminal Radar Program at selected airports. TRSAs were never controlled airspace from a regulatory standpoint because the establishment of TRSAs was never subject to the rulemaking process; consequently, TRSAs are not contained in 14 CFR Part 71 nor are there any TRSA operating rules in 14 CFR Part 91. Part of the Airport Radar Service Area (ARSA) program was to eventually replace all TRSAs. However, the ARSA requirements became relatively stringent and it was subsequently decided that TRSAs would have to meet ARSA criteria before they would be converted. TRSAs do not fit into any of the U.S. airspace classes; therefore, they will continue to be non−Part 71 airspace areas where participating pilots can receive additional radar services which have been redefined as TRSA Service. AIM Part 93, unless otherwise authorized by air traffic control. Not all areas listed in 14 CFR Part 93 are designated SFRA, but special air traffic rules apply to all areas described in 14 CFR Part 93. REFERENCE− 14 CFR Part 93, Special Air Traffic Rules FAA Order JO 7110.65, Para 9−2−10, Special Air Traffic Rules (SATR) and Special Flight Rules Area (SFRA) PCG − Special Air Traffic Rules (SATR) c. Participation. Each person operating an aircraft to, from, or within airspace designated as a SATR area or SFRA must adhere to the special air traffic rules set forth in 14 CFR Part 93, as applicable, unless otherwise authorized or required by ATC. d. Charts. SFRAs are depicted on VFR sectional, terminal area, and helicopter route charts. (See FIG 3−5−4.) FIG 3−5−4 SFRA Boundary b. TRSAs. The primary airport(s) within the TRSA become(s) Class D airspace. The remaining portion of the TRSA overlies other controlled airspace which is normally Class E airspace beginning at 700 or 1,200 feet and established to transition to/from the en route/terminal environment. c. Participation. Pilots operating under VFR are encouraged to contact the radar approach control and avail themselves of the TRSA Services. However, participation is voluntary on the part of the pilot. See Chapter 4, Air Traffic Control, for details and procedures. d. Charts. TRSAs are depicted on VFR sectional and terminal area charts with a solid black line and altitudes for each segment. The Class D portion is charted with a blue segmented line. 3−5−7. Special Air Traffic Rules (SATR) and Special Flight Rules Area (SFRA) a. Background. The Code of Federal Regulations (CFR) prescribes special air traffic rules for aircraft operating within the boundaries of certain designated airspace. These areas are listed in 14 CFR Part 93 and can be found throughout the NAS. Procedures, nature of operations, configuration, size, and density of traffic vary among the identified areas. b. SFRAs. Airspace of defined dimensions, above land areas or territorial waters, within which the flight of aircraft is subject to the rules set forth in 14 CFR Other Airspace Areas e. Additional information and resources regarding SFRA, including procedures for flight in individual areas, may be found on the FAA Safety website at http://www.faasafety.gov 3−5−8. Weather Reconnaissance Area (WRA) a. General. Hurricane Hunters from the United States Air Force Reserve 53 rd Weather Reconnaissance Squadron (WRS) and the National Oceanic and Atmospheric Administration (NOAA) Aircraft Operations Center (AOC) operate weather reconnaissance/research aircraft missions, in support of the National Hurricane Operations Plan (NHOP), to gather meteorological data on hurricanes and tropical cyclones. 53 rd WRS and NOAA AOC aircraft normally conduct these missions in airspace 3−5−9 7110.65R CHG 2 AIM AIM identified in a published WRA Notice to Air Missions (NOTAM). b. WRAs. Airspace with defined dimensions and published by a NOTAM, which is established to support weather reconnaissance/research flights. ATC services are not provided within WRAs. Only participating weather reconnaissance/research aircraft from the 53rd WRS and NOAA AOC are permitted to operate within a WRA. A WRA may only be established in airspace within U. S. Flight Information Regions (FIR) outside of U. S. territorial airspace. c. A published WRA NOTAM describes the airspace dimensions of the WRA and the expected activities within the WRA. WRAs may border adjacent foreign FIRs, but are wholly contained within U.S. FIRs. As ATC services are not provided within a WRA, non−participating aircraft should avoid WRAs, and IFR aircraft should expect to be rerouted to avoid WRAs. 3−5−10 3/15/07 12/2/21 6/17/21 3−5−9. Other Non−Charted Airspace Areas a. Stationary or Moving Altitude Reservation (ALTRV). A Stationary or Moving ALTRV is announced via an airspace NOTAM issued by the Central Altitude Reservation Facility (CARF) or ARTCC. These announcements will appear in CARF and/or ARTCC NOTAMS. This airspace ensures non−participating IFR aircraft remain separated from special activity. Non−participating VFR aircraft are permitted to fly through the area but should exercise vigilance. b. ATC ASSIGNED AIRSPACE. Airspace of defined vertical/lateral limits, assigned by ATC, for the purpose of providing air traffic segregation between the specified activities being conducted within the assigned airspace and other IFR air traffic. ATCAA locations and scheduled activation information can be found on the FAA SUA website; a NOTAM will not be issued to announce the activation of this airspace. Other Airspace Areas 12/2/21 6/17/21 AIM Chapter 4. Air Traffic Control Section 1. Services Available to Pilots 4−1−1. Air Route Traffic Control Centers Centers are established primarily to provide air traffic service to aircraft operating on IFR flight plans within controlled airspace, and principally during the en route phase of flight. 4−1−2. Control Towers Towers have been established to provide for a safe, orderly and expeditious flow of traffic on and in the vicinity of an airport. When the responsibility has been so delegated, towers also provide for the separation of IFR aircraft in the terminal areas. REFERENCE− AIM, Paragraph 5−4−3 , Approach Control. 4−1−3. Flight Service Stations Flight Service Stations (FSSs) are air traffic facilities that provide pilot briefings, flight plan processing, en route flight advisories, search and rescue services, and assistance to lost aircraft and aircraft in emergency situations. FSSs also relay ATC clearances, process Notices to Air Missions, and broadcast aviation weather and aeronautical information. In Alaska, designated FSSs also take weather observations, and provide Airport Advisory Services (AAS). 4−1−4. Recording and Monitoring a. Calls to air traffic control (ATC) facilities (ARTCCs, Towers, FSSs, Central Flow, and Operations Centers) over radio and ATC operational telephone lines (lines used for operational purposes such as controller instructions, briefings, opening and closing flight plans, issuance of IFR clearances and amendments, counter hijacking activities, etc.) may be monitored and recorded for operational uses such as accident investigations, accident prevention, search and rescue purposes, specialist training and evaluation, and technical evaluation and repair of control and communications systems. b. Where the public access telephone is recorded, a beeper tone is not required. In place of the “beep” Services Available to Pilots tone the FCC has substituted a mandatory requirement that persons to be recorded be given notice they are to be recorded and give consent. Notice is given by this entry, consent to record is assumed by the individual placing a call to the operational facility. 4−1−5. Communications Release of IFR Aircraft Landing at an Airport Without an Operating Control Tower Aircraft operating on an IFR flight plan, landing at an airport without an operating control tower will be advised to change to the airport advisory frequency when direct communications with ATC are no longer required. Towers and centers do not have nontower airport traffic and runway in use information. The instrument approach may not be aligned with the runway in use; therefore, if the information has not already been obtained, pilots should make an expeditious change to the airport advisory frequency when authorized. REFERENCE− AIM, Paragraph 5−4−4 , Advance Information on Instrument Approach 4−1−6. Pilot Visits to Air Traffic Facilities Pilots are encouraged to participate in local pilot/air traffic control outreach activities. However, due to security and workload concerns, requests for air traffic facility visits may not always be approved. Therefore, visit requests should be submitted through the air traffic facility as early as possible. Pilots should contact the facility and advise them of the number of persons in the group, the time and date of the proposed visit, and the primary interest of the group. The air traffic facility will provide further instructions if a request can be approved. REFERENCE− FAA Order 1600.69, FAA Facility Security Management Program 4−1−7. Operation Rain Check Operation Rain Check is a program designed and managed by local air traffic control facility management. Its purpose is to familiarize pilots and aspiring pilots with the ATC system, its functions, responsibilities and benefits. 4−1−1 7110.65R CHG 2 AIM AIM REFERENCE− FAA Order JO 7210.3, Paragraph 4−2−2, Pilot Education FAA Order 1600.69, FAA Facility Security Management Program 4−1−8. Approach Control Service for VFR Arriving Aircraft a. Numerous approach control facilities have established programs for arriving VFR aircraft to contact approach control for landing information. This information includes: wind, runway, and altimeter setting at the airport of intended landing. This information may be omitted if contained in the Automatic Terminal Information Service (ATIS) broadcast and the pilot states the appropriate ATIS code. NOTE− Pilot use of “have numbers” does not indicate receipt of the ATIS broadcast. In addition, the controller will provide traffic advisories on a workload permitting basis. b. Such information will be furnished upon initial contact with concerned approach control facility. The pilot will be requested to change to the tower frequency at a predetermined time or point, to receive further landing information. c. Where available, use of this procedure will not hinder the operation of VFR flights by requiring excessive spacing between aircraft or devious routing. d. Compliance with this procedure is not mandatory but pilot participation is encouraged. REFERENCE− AIM, Paragraph 4−1−18 , Terminal Radar Services for VFR Aircraft NOTE− Approach control services for VFR aircraft are normally dependent on ATC radar. These services are not available during periods of a radar outage. Approach control services for VFR aircraft are limited when CENRAP is in use. 4−1−9. Traffic Advisory Practices at Airports Without Operating Control Towers (See TBL 4−1−1.) a. Airport Operations Without Operating Control Tower 1. There is no substitute for alertness while in the vicinity of an airport. It is essential that pilots be alert and look for other traffic and exchange traffic information when approaching or departing an 4−1−2 3/15/07 12/2/21 6/17/21 airport without an operating control tower. This is of particular importance since other aircraft may not have communication capability or, in some cases, pilots may not communicate their presence or intentions when operating into or out of such airports. To achieve the greatest degree of safety, it is essential that: (a) All radio−equipped aircraft transmit/receive on a common frequency identified for the purpose of airport advisories; and (b) Pilots use the correct airport name, as identified in appropriate aeronautical publications, to reduce the risk of confusion when communicating their position, intentions, and/or exchanging traffic information. 2. An airport may have a full or part-time tower or FSS located on the airport, a full or part-time UNICOM station or no aeronautical station at all. There are three ways for pilots to communicate their intention and obtain airport/traffic information when operating at an airport that does not have an operating tower: by communicating with an FSS, a UNICOM operator, or by making a self-announce broadcast. NOTE− FSS airport advisories are available only in Alaska. 3. Many airports are now providing completely automated weather, radio check capability and airport advisory information on an automated UNICOM system. These systems offer a variety of features, typically selectable by microphone clicks, on the UNICOM frequency. Availability of the automated UNICOM will be published in the Chart Supplement U.S. and approach charts. b. Communicating on a Common Frequency 1. The key to communicating at an airport without an operating control tower is selection of the correct common frequency. The acronym CTAF which stands for Common Traffic Advisory Frequency, is synonymous with this program. A CTAF is a frequency designated for the purpose of carrying out airport advisory practices while operating to or from an airport without an operating control tower. The CTAF may be a UNICOM, MULTICOM, FSS, or tower frequency and is identified in appropriate aeronautical publications. NOTE− FSS frequencies are available only in Alaska. Services Available to Pilots 6/17/21 AIM TBL 4−1−1 Summary of Recommended Communication Procedures Communication/Broadcast Procedures Facility at Airport Practice Instrument Approach Frequency Use Outbound Inbound 1. UNICOM (No Tower or FSS) Communicate with UNICOM station on published CTAF frequency (122.7; 122.8; 122.725; 122.975; or 123.0). If unable to contact UNICOM station, use self-announce procedures on CTAF. Before taxiing and before taxiing on the runway for departure. 10 miles out. Entering downwind, base, and final. Leaving the runway. 2. No Tower, FSS, or UNICOM Self-announce on MULTICOM frequency 122.9. Before taxiing and before taxiing on the runway for departure. 10 miles out. Entering downwind, base, and final. Leaving the runway. Departing final approach fix (name) or on final approach segment inbound. 3. No Tower in operation, FSS open (Alaska only) Communicate with FSS on CTAF frequency. Before taxiing and before taxiing on the runway for departure. 10 miles out. Entering downwind, base, and final. Leaving the runway. Approach completed/terminated. 4. FSS Closed (No Tower) Self-announce on CTAF. Before taxiing and before taxiing on the runway for departure. 10 miles out. Entering downwind, base, and final. Leaving the runway. 5. Tower or FSS not in operation Self-announce on CTAF. Before taxiing and before taxiing on the runway for departure. 10 miles out. Entering downwind, base, and final. Leaving the runway. 6. Designated CTAF Area (Alaska Only) Self-announce on CTAF designated on chart or Chart Supplement Alaska. Before taxiing and before taxiing on the runway for departure until leaving designated area. When entering designated CTAF area. 2. CTAF (Alaska Only). In Alaska, a CTAF may also be designated for the purpose of carrying out advisory practices while operating in designated areas with a high volume of VFR traffic. 3. The CTAF frequency for a particular airport or area is contained in the Chart Supplement U.S., Chart Supplement Alaska, Alaska Terminal Publication, Instrument Approach Procedure Charts, and Instrument Departure Procedure (DP) Charts. Also, the CTAF frequency can be obtained by contacting any FSS. Use of the appropriate CTAF, combined with a visual alertness and application of the following recommended good operating practices, will enhance safety of flight into and out of all uncontrolled airports. Services Available to Pilots c. Recommended Traffic Advisory Practices 1. Pilots of inbound traffic should monitor and communicate as appropriate on the designated CTAF from 10 miles to landing. Pilots of departing aircraft should monitor/communicate on the appropriate frequency from start-up, during taxi, and until 10 miles from the airport unless the CFRs or local procedures require otherwise. 2. Pilots of aircraft conducting other than arriving or departing operations at altitudes normally used by arriving and departing aircraft should monitor/communicate on the appropriate frequency while within 10 miles of the airport unless required to do otherwise by the CFRs or local procedures. Such 4−1−3 AIM 6/17/21 operations include parachute jumping/dropping, en route, practicing maneuvers, etc. 3. In Alaska, pilots of aircraft conducting other than arriving or departing operations in designated CTAF areas should monitor/communicate on the appropriate frequency while within the designated area, unless required to do otherwise by CFRs or local procedures. Such operations include parachute jumping/dropping, en route, practicing maneuvers, etc. REFERENCE− AIM, Paragraph 3−5−4 , Parachute Jump Aircraft Operations d. Airport Advisory/Information Services Provided by a FSS 1. There are two advisory type services provided at selected airports. (a) Local Airport Advisory (LAA) is available only in Alaska and provided at airports that have a FSS physically located on the airport, which does not have a control tower or where the tower is operated on a part−time basis. The CTAF for LAA airports is disseminated in the appropriate aeronautical publications. (b) Remote Airport Information Service (RAIS) is provided in support of special events at nontowered airports by request from the airport authority. 2. In communicating with a CTAF FSS, check the airport’s automated weather and establish two−way communications before transmitting outbound/inbound intentions or information. An inbound aircraft should initiate contact approximately 10 miles from the airport, reporting aircraft identification and type, altitude, location relative to the airport, intentions (landing or over flight), possession of the automated weather, and request airport advisory or airport information service. A departing aircraft should initiate contact before taxiing, reporting aircraft identification and type, VFR or IFR, location on the airport, intentions, direction of take−off, possession of the automated weather, and request airport advisory or information service. Also, report intentions before taxiing onto the active runway for departure. If you must change frequencies for other service after initial report to FSS, return to FSS frequency for traffic update. (a) Inbound 4−1−4 EXAMPLE− Vero Beach radio, Centurion Six Niner Delta Delta is ten miles south, two thousand, landing Vero Beach. I have the automated weather, request airport advisory. (b) Outbound EXAMPLE− Vero Beach radio, Centurion Six Niner Delta Delta, ready to taxi to runway 22, VFR, departing to the southwest. I have the automated weather, request airport advisory. 3. Airport advisory service includes wind direction and velocity, favored or designated runway, altimeter setting, known airborne and ground traffic, NOTAMs, airport taxi routes, airport traffic pattern information, and instrument approach procedures. These elements are varied so as to best serve the current traffic situation. Some airport managers have specified that under certain wind or other conditions designated runways be used. Pilots should advise the FSS of the runway they intend to use. CAUTION− All aircraft in the vicinity of an airport may not be in communication with the FSS. e. Information Provided by Aeronautical Advisory Stations (UNICOM) 1. UNICOM is a nongovernment air/ground radio communication station which may provide airport information at public use airports where there is no tower or FSS. 2. On pilot request, UNICOM stations may provide pilots with weather information, wind direction, the recommended runway, or other necessary information. If the UNICOM frequency is designated as the CTAF, it will be identified in appropriate aeronautical publications. f. Unavailability of Information from FSS or UNICOM Should LAA by an FSS or Aeronautical Advisory Station UNICOM be unavailable, wind and weather information may be obtainable from nearby controlled airports via Automatic Terminal Information Service (ATIS) or Automated Weather Observing System (AWOS) frequency. g. Self-Announce Position and/or Intentions 1. General. Self-announce is a procedure whereby pilots broadcast their position or intended flight activity or ground operation on the designated CTAF. This procedure is used primarily at airports which do not have an FSS on the airport. The Services Available to Pilots 6/17/21 self-announce procedure should also be used if a pilot is unable to communicate with the FSS on the designated CTAF. Pilots stating, “Traffic in the area, please advise” is not a recognized Self−Announce Position and/or Intention phrase and should not be used under any condition. 2. If an airport has a tower and it is temporarily closed, or operated on a part-time basis and there is no FSS on the airport or the FSS is closed, use the CTAF to self-announce your position or intentions. 3. Where there is no tower, FSS, or UNICOM station on the airport, use MULTICOM frequency 122.9 for self-announce procedures. Such airports will be identified in appropriate aeronautical information publications. 4. Practice Approaches. Pilots conducting practice instrument approaches should be particularly alert for other aircraft that may be departing in the opposite direction. When conducting any practice approach, regardless of its direction relative to other airport operations, pilots should make announcements on the CTAF as follows: (a) Departing the final approach fix, inbound (nonprecision approach) or departing the outer marker or fix used in lieu of the outer marker, inbound (precision approach); (b) Established on the final approach segment or immediately upon being released by ATC; (c) Upon completion or termination of the approach; and (d) Upon executing the missed approach procedure. 5. Departing aircraft should always be alert for arrival aircraft coming from the opposite direction. 6. Recommended self-announce phraseologies: It should be noted that aircraft operating to or from another nearby airport may be making self-announce broadcasts on the same UNICOM or MULTICOM frequency. To help identify one airport from another, the airport name should be spoken at the beginning and end of each self-announce transmission. (a) Inbound EXAMPLE− Strawn traffic, Apache Two Two Five Zulu, (position), (altitude), (descending) or entering downwind/base/final (as appropriate) runway one seven full stop, touch−and− Services Available to Pilots AIM go, Strawn. Strawn traffic Apache Two Two Five Zulu clear of runway one seven Strawn. (b) Outbound EXAMPLE− Strawn traffic, Queen Air Seven One Five Five Bravo (location on airport) taxiing to runway two six Strawn. Strawn traffic, Queen Air Seven One Five Five Bravo departing runway two six. Departing the pattern to the (direction), climbing to (altitude) Strawn. (c) Practice Instrument Approach EXAMPLE− Strawn traffic, Cessna Two One Four Three Quebec (position from airport) inbound descending through (altitude) practice (name of approach) approach runway three five Strawn. Strawn traffic, Cessna Two One Four Three Quebec practice (type) approach completed or terminated runway three five Strawn. h. UNICOM Communications Procedures 1. In communicating with a UNICOM station, the following practices will help reduce frequency congestion, facilitate a better understanding of pilot intentions, help identify the location of aircraft in the traffic pattern, and enhance safety of flight: (a) Select the correct UNICOM frequency. (b) State the identification of the UNICOM station you are calling in each transmission. (c) Speak slowly and distinctly. (d) Report approximately 10 miles from the airport, reporting altitude, and state your aircraft type, aircraft identification, location relative to the airport, state whether landing or overflight, and request wind information and runway in use. (e) Report on downwind, base, and final approach. (f) Report leaving the runway. 2. Recommended UNICOM phraseologies: (a) Inbound PHRASEOLOGY− FREDERICK UNICOM CESSNA EIGHT ZERO ONE TANGO FOXTROT 10 MILES SOUTHEAST DESCENDING THROUGH (altitude) LANDING FREDERICK, REQUEST WIND AND RUNWAY INFORMATION FREDERICK. FREDERICK TRAFFIC CESSNA EIGHT ZERO ONE TANGO FOXTROT ENTERING DOWNWIND/BASE/ 4−1−5 AIM 6/17/21 FINAL (as appropriate) FOR RUNWAY ONE NINER (full stop/touch−and−go) FREDERICK. FREDERICK TRAFFIC CESSNA EIGHT ZERO ONE TANGO FOXTROT CLEAR OF RUNWAY ONE NINER FREDERICK. (b) Outbound PHRASEOLOGY− FREDERICK UNICOM CESSNA EIGHT ZERO ONE TANGO FOXTROT (location on airport) TAXIING TO RUNWAY ONE NINER, REQUEST WIND AND TRAFFIC INFORMATION FREDERICK. FREDERICK TRAFFIC CESSNA EIGHT ZERO ONE TANGO FOXTROT DEPARTING RUNWAY ONE NINER. “REMAINING IN THE PATTERN” OR “DEPARTING THE PATTERN TO THE (direction) (as appropriate)” FREDERICK. 4−1−10. IFR Approaches/Ground Vehicle Operations a. IFR Approaches. When operating in accordance with an IFR clearance and ATC approves a change to the advisory frequency, make an expeditious change to the CTAF and employ the recommended traffic advisory procedures. b. Ground Vehicle Operation. Airport ground vehicles equipped with radios should monitor the CTAF frequency when operating on the airport movement area and remain clear of runways/taxiways being used by aircraft. Radio transmissions from ground vehicles should be confined to safety-related matters. c. Radio Control of Airport Lighting Systems. Whenever possible, the CTAF will be used to control airport lighting systems at airports without operating control towers. This eliminates the need for pilots to change frequencies to turn the lights on and allows a continuous listening watch on a single frequency. The CTAF is published on the instrument approach chart and in other appropriate aeronautical information publications. 4−1−11. Designated UNICOM/MULTICOM Frequencies Frequency use a. The following listing depicts UNICOM and MULTICOM frequency uses as designated by the Federal Communications Commission (FCC). (See TBL 4−1−2.) TBL 4−1−2 Unicom/Multicom Frequency Usage Use Frequency Airports without an operating control tower. 122.700 122.725 122.800 122.975 123.000 123.050 123.075 (MULTICOM FREQUENCY) Activities of a temporary, seasonal, emergency nature or search and rescue, as well as, airports with no tower, FSS, or UNICOM. 122.900 (MULTICOM FREQUENCY) Forestry management and fire suppression, fish and game management and protection, and environmental monitoring and protection. Airports with a control tower or FSS on airport. 122.925 122.950 NOTE− 1. In some areas of the country, frequency interference may be encountered from nearby airports using the same UNICOM frequency. Where there is a problem, UNICOM operators are encouraged to develop a “least interference” frequency assignment plan for airports concerned using the frequencies designated for airports without operating control towers. UNICOM licensees are encouraged to apply for UNICOM 25 kHz spaced channel frequencies. Due to the extremely limited number of frequencies with 50 kHz channel spacing, 25 kHz channel spacing should be implemented. UNICOM licensees may then request FCC to assign frequencies in accordance with the plan, which FCC will review and consider for approval. 2. Wind direction and runway information may not be available on UNICOM frequency 122.950. b. The following listing depicts other frequency uses as designated by the Federal Communications Commission (FCC). (See TBL 4−1−3.) 4−1−6 Services Available to Pilots 6/17/21 AIM TBL 4−1−3 Other Frequency Usage Designated by FCC Use Frequency Air-to-air communication (private fixed wing aircraft). Helicopter air−to−air communications; air traffic control operations. Aviation instruction, Glider, Hot Air Balloon (not to be used for advisory service). Assignment to flight test land and aircraft stations (not for air−to−air communication except for those aircraft operating in an oceanic FIR). 122.750 123.025 123.300 123.500 123.4001 123.4502 1This frequency is available only to itinerant stations that have a requirement to be periodically transferred to various locations. 2Mobile station operations on these frequencies are limited to an area within 320 km (200 mi) of an associated flight test land station. 4−1−12. Use of UNICOM for ATC Purposes UNICOM service may be used for ATC purposes, only under the following circumstances: a. Revision to proposed departure time. b. Takeoff, arrival, or flight plan cancellation time. c. ATC clearance, provided arrangements are made between the ATC facility and the UNICOM licensee to handle such messages. 4−1−13. Automatic Terminal Information Service (ATIS) a. ATIS is the continuous broadcast of recorded noncontrol information in selected high activity terminal areas. Its purpose is to improve controller effectiveness and to relieve frequency congestion by automating the repetitive transmission of essential but routine information. The information is continuously broadcast over a discrete VHF radio frequency or the voice portion of a local NAVAID. Arrival ATIS transmissions on a discrete VHF radio frequency are engineered according to the individual facility requirements, which would normally be a protected service volume of 20 NM to 60 NM from the ATIS site and a maximum altitude of 25,000 feet AGL. In Services Available to Pilots the case of a departure ATIS, the protected service volume cannot exceed 5 NM and 100 feet AGL. At most locations, ATIS signals may be received on the surface of the airport, but local conditions may limit the maximum ATIS reception distance and/or altitude. Pilots are urged to cooperate in the ATIS program as it relieves frequency congestion on approach control, ground control, and local control frequencies. The Chart Supplement U.S. indicates airports for which ATIS is provided. b. ATIS information includes: 1. Airport/facility name 2. Phonetic letter code 3. Time of the latest weather sequence (UTC) 4. Weather information consisting of: (a) Wind direction and velocity (b) Visibility (c) Obstructions to vision (d) Present weather consisting of: sky condition, temperature, dew point, altimeter, a density altitude advisory when appropriate, and other pertinent remarks included in the official weather observation 5. Instrument approach and runway in use. The ceiling/sky condition, visibility, and obstructions to vision may be omitted from the ATIS broadcast if the ceiling is above 5,000 feet and the visibility is more than 5 miles. The departure runway will only be given if different from the landing runway except at locations having a separate ATIS for departure. The broadcast may include the appropriate frequency and instructions for VFR arrivals to make initial contact with approach control. Pilots of aircraft arriving or departing the terminal area can receive the continuous ATIS broadcast at times when cockpit duties are least pressing and listen to as many repeats as desired. ATIS broadcast must be updated upon the receipt of any official hourly and special weather. A new recording will also be made when there is a change in other pertinent data such as runway change, instrument approach in use, etc. EXAMPLE− Dulles International information Sierra. One four zero zero zulu. Wind three five zero at eight. Visibility one zero. Ceiling four thousand five hundred broken. Temperature three four. Dew point two eight. Altimeter three zero one zero. ILS runway one right approach in use. Departing 4−1−7 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 runway three zero. Advise on initial contact you have information sierra. 4−1−14. Automatic Flight Information Service (AFIS) − Alaska FSSs Only c. Pilots should listen to ATIS broadcasts whenever ATIS is in operation. a. AFIS is the continuous broadcast of recorded non−control information at airports in Alaska where an FSS provides local airport advisory service. Its purpose is to improve FSS specialist efficiency by reducing frequency congestion on the local airport advisory frequency. d. Pilots should notify controllers on initial contact that they have received the ATIS broadcast by repeating the alphabetical code word appended to the broadcast. EXAMPLE− “Information Sierra received.” e. When a pilot acknowledges receipt of the ATIS broadcast, controllers may omit those items contained in the broadcast if they are current. Rapidly changing conditions will be issued by ATC and the ATIS will contain words as follows: EXAMPLE− “Latest ceiling/visibility/altimeter/wind/(other conditions) will be issued by approach control/tower.” NOTE− The absence of a sky condition or ceiling and/or visibility on ATIS indicates a sky condition or ceiling of 5,000 feet or above and visibility of 5 miles or more. A remark may be made on the broadcast, “the weather is better than 5000 and 5,” or the existing weather may be broadcast. f. Controllers will issue pertinent information to pilots who do not acknowledge receipt of a broadcast or who acknowledge receipt of a broadcast which is not current. g. To serve frequency limited aircraft, FSSs are equipped to transmit on the omnirange frequency at most en route VORs used as ATIS voice outlets. Such communication interrupts the ATIS broadcast. Pilots of aircraft equipped to receive on other FSS frequencies are encouraged to do so in order that these override transmissions may be kept to an absolute minimum. h. While it is a good operating practice for pilots to make use of the ATIS broadcast where it is available, some pilots use the phrase “have numbers” in communications with the control tower. Use of this phrase means that the pilot has received wind, runway, and altimeter information ONLY and the tower does not have to repeat this information. It does not indicate receipt of the ATIS broadcast and should never be used for this purpose. 4−1−8 1. The AFIS broadcast will automate the repetitive transmission of essential but routine information (for example, weather, favored runway, braking action, airport NOTAMs, etc.). The information is continuously broadcast over a discrete VHF radio frequency (usually the ASOS frequency). 2. Use of AFIS is not mandatory, but pilots who choose to utilize two−way radio communications with the FSS are urged to listen to AFIS, as it relieves frequency congestion on the local airport advisory frequency. AFIS broadcasts are updated upon receipt of any official hourly and special weather, and changes in other pertinent data. 3. When a pilot acknowledges receipt of the AFIS broadcast, FSS specialists may omit those items contained in the broadcast if they are current. When rapidly changing conditions exist, the latest ceiling, visibility, altimeter, wind or other conditions may be omitted from the AFIS and will be issued by the FSS specialist on the appropriate radio frequency. EXAMPLE− “Kotzebue information ALPHA. One six five five zulu. Wind, two one zero at five; visibility two, fog; ceiling one hundred overcast; temperature minus one two, dew point minus one four; altimeter three one zero five. Altimeter in excess of three one zero zero, high pressure altimeter setting procedures are in effect. Favored runway two six. Weather in Kotzebue surface area is below V−F−R minima − an ATC clearance is required. Contact Kotzebue Radio on 123.6 for traffic advisories and advise intentions. Notice to Air Missions, Hotham NDB out of service. Transcribed Weather Broadcast out of service. Advise on initial contact you have ALPHA.” NOTE− The absence of a sky condition or ceiling and/or visibility on Alaska FSS AFIS indicates a sky condition or ceiling of 5,000 feet or above and visibility of 5 miles or more. A remark may be made on the broadcast, “the weather is better than 5000 and 5.” b. Pilots should listen to Alaska FSSs AFIS broadcasts whenever Alaska FSSs AFIS is in operation. Services Available to Pilots 6/17/21 NOTE− Some Alaska FSSs are open part time and/or seasonally. c. Pilots should notify controllers on initial contact that they have received the Alaska FSSs AFIS broadcast by repeating the phonetic alphabetic letter appended to the broadcast. EXAMPLE− “Information Alpha received.” d. While it is a good operating practice for pilots to make use of the Alaska FSS AFIS broadcast where it is available, some pilots use the phrase “have numbers” in communications with the FSS. Use of this phrase means that the pilot has received wind, runway, and altimeter information ONLY and the Alaska FSS does not have to repeat this information. It does not indicate receipt of the AFIS broadcast and should never be used for this purpose. 4−1−15. Radar Traffic Information Service This is a service provided by radar ATC facilities. Pilots receiving this service are advised of any radar target observed on the radar display which may be in such proximity to the position of their aircraft or its intended route of flight that it warrants their attention. This service is not intended to relieve the pilot of the responsibility for continual vigilance to see and avoid other aircraft. a. Purpose of the Service 1. The issuance of traffic information as observed on a radar display is based on the principle of assisting and advising a pilot that a particular radar target’s position and track indicates it may intersect or pass in such proximity to that pilot’s intended flight path that it warrants attention. This is to alert the pilot to the traffic, to be on the lookout for it, and thereby be in a better position to take appropriate action should the need arise. 2. Pilots are reminded that the surveillance radar used by ATC does not provide altitude information unless the aircraft is equipped with Mode C and the radar facility is capable of displaying altitude information. b. Provisions of the Service 1. Many factors, such as limitations of the radar, volume of traffic, controller workload and communications frequency congestion, could prevent the controller from providing this service. Controllers Services Available to Pilots AIM possess complete discretion for determining whether they are able to provide or continue to provide this service in a specific case. The controller’s reason against providing or continuing to provide the service in a particular case is not subject to question nor need it be communicated to the pilot. In other words, the provision of this service is entirely dependent upon whether controllers believe they are in a position to provide it. Traffic information is routinely provided to all aircraft operating on IFR flight plans except when the pilot declines the service, or the pilot is operating within Class A airspace. Traffic information may be provided to flights not operating on IFR flight plans when requested by pilots of such flights. NOTE− Radar ATC facilities normally display and monitor both primary and secondary radar as well as ADS−B, except that secondary radar or ADS−B may be used as the sole display source in Class A airspace, and under some circumstances outside of Class A airspace (beyond primary coverage and in en route areas where only secondary and/or ADS−B is available). Secondary radar and/or ADS−B may also be used outside Class A airspace as the sole display source when the primary radar is temporarily unusable or out of service. Pilots in contact with the affected ATC facility are normally advised when a temporary outage occurs; i.e., “primary radar out of service; traffic advisories available on transponder or ADS−B aircraft only.” This means simply that only aircraft that have transponders and ADS−B installed and in use will be depicted on ATC displays when the primary and/or secondary radar is temporarily out of service. 2. When receiving VFR radar advisory service, pilots should monitor the assigned frequency at all times. This is to preclude controllers’ concern for radio failure or emergency assistance to aircraft under the controller’s jurisdiction. VFR radar advisory service does not include vectors away from conflicting traffic unless requested by the pilot. When advisory service is no longer desired, advise the controller before changing frequencies and then change your transponder code to 1200, if applicable. Pilots should also inform the controller when changing VFR cruising altitude. Except in programs where radar service is automatically terminated, the controller will advise the aircraft when radar is terminated. NOTE− Participation by VFR pilots in formal programs implemented at certain terminal locations constitutes pilot request. This also applies to participating pilots at those locations where arriving VFR flights are encouraged to 4−1−9 AIM 6/17/21 make their first contact with the tower on the approach control frequency. c. Issuance of Traffic Information. Traffic information will include the following concerning a target which may constitute traffic for an aircraft that is: 1. Radar identified (a) Azimuth from the aircraft in terms of the 12 hour clock, or (b) When rapidly maneuvering civil test or military aircraft prevent accurate issuance of traffic as in (a) above, specify the direction from an aircraft’s position in terms of the eight cardinal compass points (N, NE, E, SE, S, SW, W, NW). This method must be terminated at the pilot’s request. miles; (c) Distance from the aircraft in nautical (d) Direction in which the target is proceeding; and d. The examples depicted in the following figures point out the possible error in the position of this traffic when it is necessary for a pilot to apply drift correction to maintain this track. This error could also occur in the event a change in course is made at the time radar traffic information is issued. FIG 4−1−1 Induced Error in Position of Traffic WIND TRACK TRACK (A) (B) EXAMPLE− In FIG 4−1−1 traffic information would be issued to the pilot of aircraft “A” as 12 o’clock. The actual position of the traffic as seen by the pilot of aircraft “A” would be 2 o’clock. Traffic information issued to aircraft “B” would also be given as 12 o’clock, but in this case, the pilot of “B” would see the traffic at 10 o’clock. (e) Type of aircraft and altitude if known. EXAMPLE− Traffic 10 o’clock, 3 miles, west-bound (type aircraft and altitude, if known, of the observed traffic). The altitude may be known, by means of Mode C, but not verified with the pilot for accuracy. (To be valid for separation purposes by ATC, the accuracy of Mode C readouts must be verified. This is usually accomplished upon initial entry into the radar system by a comparison of the readout to pilot stated altitude, or the field elevation in the case of continuous readout being received from an aircraft on the airport.) When necessary to issue traffic advisories containing unverified altitude information, the controller will issue the indicated altitude of the aircraft. The pilot may upon receipt of traffic information, request a vector (heading) to avoid such traffic. The vector will be provided to the extent possible as determined by the controller provided the aircraft to be vectored is within the airspace under the jurisdiction of the controller. 2. Not radar identified fix; (a) Distance and direction with respect to a (b) Direction in which the target is proceeding; and (c) Type of aircraft and altitude if known. EXAMPLE− Traffic 8 miles south of the airport northeast−bound, (type aircraft and altitude if known). 4−1−10 FIG 4−1−2 Induced Error in Position of Traffic TRACK WIND (D) (C) TRACK EXAMPLE− In FIG 4−1−2 traffic information would be issued to the pilot of aircraft “C” as 2 o’clock. The actual position of the traffic as seen by the pilot of aircraft “C” would be 3 o’clock. Traffic information issued to aircraft “D” would be at an 11 o’clock position. Since it is not necessary for the pilot of aircraft “D” to apply wind correction (crab) to remain on track, the actual position of the traffic issued would be correct. Since the radar controller can only observe aircraft track (course) on the radar display, traffic advisories are issued accordingly, and pilots should give due consideration to this fact when looking for reported traffic. 4−1−16. Safety Alert A safety alert will be issued to pilots of aircraft being controlled by ATC if the controller is aware the aircraft is at an altitude which, in the controller’s Services Available to Pilots 6/17/21 judgment, places the aircraft in unsafe proximity to terrain, obstructions or other aircraft. The provision of this service is contingent upon the capability of the controller to have an awareness of a situation involving unsafe proximity to terrain, obstructions and uncontrolled aircraft. The issuance of a safety alert cannot be mandated, but it can be expected on a reasonable, though intermittent basis. Once the alert is issued, it is solely the pilot’s prerogative to determine what course of action, if any, to take. This procedure is intended for use in time critical situations where aircraft safety is in question. Noncritical situations should be handled via the normal traffic alert procedures. a. Terrain or Obstruction Alert 1. Controllers will immediately issue an alert to the pilot of an aircraft under their control when they recognize that the aircraft is at an altitude which, in their judgment, may be in an unsafe proximity to terrain/obstructions. The primary method of detecting unsafe proximity is through Mode C automatic altitude reports. EXAMPLE− Low altitude alert Cessna Three Four Juliet, check your altitude immediately. And if the aircraft is not yet on final approach, the MVA (MEA/MIA/MOCA) in your area is six thousand. 2. Most En Route and Terminal radar facilities have an automated function which, if operating, alerts controllers when a tracked Mode C equipped aircraft under their control is below or is predicted to be below a predetermined minimum safe altitude. This function, called Minimum Safe Altitude Warning (MSAW), is designed solely as a controller aid in detecting potentially unsafe aircraft proximity to terrain/obstructions. The radar facility will, when MSAW is operating, provide MSAW monitoring for all aircraft with an operating Mode C altitude encoding transponder that are tracked by the system and are: AIM 3. Due to the lack of terrain and obstacle clearance data, accurate automation databases may not be available for providing MSAW information to aircraft overflying Mexico and Canada. Air traffic facilities along the United States/Mexico/Canada borders may have MSAW computer processing inhibited where accurate terrain data is not available. b. Aircraft Conflict Alert. 1. Controllers will immediately issue an alert to the pilot of an aircraft under their control if they are aware of another aircraft which is not under their control, at an altitude which, in the controller’s judgment, places both aircraft in unsafe proximity to each other. With the alert, when feasible, the controller will offer the pilot the position of the traffic if time permits and an alternate course(s) of action. Any alternate course(s) of action the controller may recommend to the pilot will be predicated only on other traffic being worked by the controller. EXAMPLE− American Three, traffic alert, (position of traffic, if time permits), advise you turn right/left heading (degrees) and/or climb/descend to (altitude) immediately. 4−1−17. Radar Assistance to VFR Aircraft a. Radar equipped FAA ATC facilities provide radar assistance and navigation service (vectors) to VFR aircraft provided the aircraft can communicate with the facility, are within radar coverage, and can be radar identified. b. Pilots should clearly understand that authorization to proceed in accordance with such radar navigational assistance does not constitute authorization for the pilot to violate CFRs. In effect, assistance provided is on the basis that navigational guidance information issued is advisory in nature and the job of flying the aircraft safely, remains with the pilot. (b) Operating VFR and have requested MSAW monitoring. c. In many cases, controllers will be unable to determine if flight into instrument conditions will result from their instructions. To avoid possible hazards resulting from being vectored into IFR conditions, pilots should keep controllers advised of the weather conditions in which they are operating and along the course ahead. NOTE− Pilots operating VFR may request MSAW monitoring if their aircraft are equipped with Mode C transponders. d. Radar navigation assistance (vectors) may be initiated by the controller when one of the following conditions exist: EXAMPLE− Apache Three Three Papa request MSAW monitoring. 1. The controller suggests the vector and the pilot concurs. (a) Operating on an IFR flight plan; or Services Available to Pilots 4−1−11 7110.65R CHG 2 AIM AIM 2. A special program has been established and vectoring service has been advertised. 3. In the controller’s judgment the vector is necessary for air safety. e. Radar navigation assistance (vectors) and other radar derived information may be provided in response to pilot requests. Many factors, such as limitations of radar, volume of traffic, communications frequency, congestion, and controller workload could prevent the controller from providing it. Controllers have complete discretion for determining if they are able to provide the service in a particular case. Their decision not to provide the service in a particular case is not subject to question. 4−1−18. Terminal Radar Services for VFR Aircraft a. Basic Radar Service: 1. In addition to the use of radar for the control of IFR aircraft, all commissioned radar facilities provide the following basic radar services for VFR aircraft: (a) Safety alerts. (b) Traffic advisories. (c) Limited radar vectoring (on a workload permitting basis). (d) Sequencing at locations where procedures have been established for this purpose and/or when covered by a Letter of Agreement. NOTE− When the stage services were developed, two basic radar services (traffic advisories and limited vectoring) were identified as “Stage I.” This definition became unnecessary and the term “Stage I” was eliminated from use. The term “Stage II” has been eliminated in conjunction with the airspace reclassification, and sequencing services to locations with local procedures and/or letters of agreement to provide this service have been included in basic services to VFR aircraft. These basic services will still be provided by all terminal radar facilities whether they include Class B, Class C, Class D or Class E airspace. “Stage III” services have been replaced with “Class B” and “TRSA” service where applicable. 2. Vectoring service may be provided when requested by the pilot or with pilot concurrence when suggested by ATC. 4−1−12 3/15/07 12/2/21 6/17/21 3. Pilots of arriving aircraft should contact approach control on the publicized frequency and give their position, altitude, aircraft call sign, type aircraft, radar beacon code (if transponder equipped), destination, and request traffic information. 4. Approach control will issue wind and runway, except when the pilot states “have numbers” or this information is contained in the ATIS broadcast and the pilot states that the current ATIS information has been received. Traffic information is provided on a workload permitting basis. Approach control will specify the time or place at which the pilot is to contact the tower on local control frequency for further landing information. Radar service is automatically terminated and the aircraft need not be advised of termination when an arriving VFR aircraft receiving radar services to a tower−controlled airport where basic radar service is provided has landed, or to all other airports, is instructed to change to tower or advisory frequency. (See FAA Order JO 7110.65, Air Traffic Control, paragraph 5−1−9, Radar Service Termination.) 5. Sequencing for VFR aircraft is available at certain terminal locations (see locations listed in the Chart Supplement U.S.). The purpose of the service is to adjust the flow of arriving VFR and IFR aircraft into the traffic pattern in a safe and orderly manner and to provide radar traffic information to departing VFR aircraft. Pilot participation is urged but is not mandatory. Traffic information is provided on a workload permitting basis. Standard radar separation between VFR or between VFR and IFR aircraft is not provided. (a) Pilots of arriving VFR aircraft should initiate radio contact on the publicized frequency with approach control when approximately 25 miles from the airport at which sequencing services are being provided. On initial contact by VFR aircraft, approach control will assume that sequencing service is requested. After radar contact is established, the pilot may use pilot navigation to enter the traffic pattern or, depending on traffic conditions, approach control may provide the pilot with routings or vectors necessary for proper sequencing with other participating VFR and IFR traffic en route to the airport. When a flight is positioned behind a preceding aircraft and the pilot reports having that aircraft in sight, the pilot will be instructed to follow the preceding aircraft. THE ATC INSTRUCTION TO FOLLOW THE PRECEDING AIRCRAFT DOES Services Available to Pilots 6/17/21 NOT AUTHORIZE THE PILOT TO COMPLY WITH ANY ATC CLEARANCE OR INSTRUCTION ISSUED TO THE PRECEDING AIRCRAFT. If other “nonparticipating” or “local” aircraft are in the traffic pattern, the tower will issue a landing sequence. If an arriving aircraft does not want radar service, the pilot should state “NEGATIVE RADAR SERVICE” or make a similar comment, on initial contact with approach control. AIM separation and sequencing of VFR aircraft will be suspended as this service is dependent on radar. The pilot will be advised that the service is not available and issued wind, runway information, and the time or place to contact the tower. Traffic information will be provided on a workload permitting basis. 5. Visual separation is used when prevailing conditions permit and it will be applied as follows: EXAMPLE− Xray ground control, November One Eight Six, Cessna One Seventy Two, ready to taxi, VFR southbound at 2,500, have information bravo and request radar traffic information. (a) When a VFR flight is positioned behind a preceding aircraft and the pilot reports having that aircraft in sight, the pilot will be instructed by ATC to follow the preceding aircraft. Radar service will be continued to the runway. THE ATC INSTRUCTION TO FOLLOW THE PRECEDING AIRCRAFT DOES NOT AUTHORIZE THE PILOT TO COMPLY WITH ANY ATC CLEARANCE OR INSTRUCTION ISSUED TO THE PRECEDING AIRCRAFT. NOTE− Following takeoff, the tower will advise when to contact departure control. (b) If other “nonparticipating” or “local” aircraft are in the traffic pattern, the tower will issue a landing sequence. (c) Pilots of aircraft transiting the area and in radar contact/communication with approach control will receive traffic information on a controller workload permitting basis. Pilots of such aircraft should give their position, altitude, aircraft call sign, aircraft type, radar beacon code (if transponder equipped), destination, and/or route of flight. (c) Departing VFR aircraft may be asked if they can visually follow a preceding departure out of the TRSA. The pilot will be instructed to follow the other aircraft provided that the pilot can maintain visual contact with that aircraft. (b) Pilots of departing VFR aircraft are encouraged to request radar traffic information by notifying ground control, or where applicable, clearance delivery, on initial contact with their request and proposed direction of flight. b. TRSA Service (Radar Sequencing and Separation Service for VFR Aircraft in a TRSA). 1. This service has been implemented at certain terminal locations. The service is advertised in the Chart Supplement U.S. The purpose of this service is to provide separation between all participating VFR aircraft and all IFR aircraft operating within the airspace defined as the Terminal Radar Service Area (TRSA). Pilot participation is urged but is not mandatory. 6. VFR aircraft will be separated from VFR/IFR aircraft by one of the following: (a) 500 feet vertical separation. (b) Visual separation. (c) Target resolution (a process to ensure that correlated radar targets do not touch). 7. Participating pilots operating VFR in a TRSA: 3. TRSAs are depicted on sectional aeronautical charts and listed in the Chart Supplement U.S. (a) Must maintain an altitude when assigned by ATC unless the altitude assignment is to maintain at or below a specified altitude. ATC may assign altitudes for separation that do not conform to 14 CFR Section 91.159. When the altitude assignment is no longer needed for separation or when leaving the TRSA, the instruction will be broadcast, “RESUME APPROPRIATE VFR ALTITUDES.” Pilots must then return to an altitude that conforms to 14 CFR Section 91.159 as soon as practicable. 4. While operating within a TRSA, pilots are provided TRSA service and separation as prescribed in this paragraph. In the event of a radar outage, (b) When not assigned an altitude, the pilot should coordinate with ATC prior to any altitude change. 2. If any aircraft does not want the service, the pilot should state “NEGATIVE TRSA SERVICE” or make a similar comment, on initial contact with approach control or ground control, as appropriate. Services Available to Pilots 4−1−13 AIM 8. Within the TRSA, traffic information on observed but unidentified targets will, to the extent possible, be provided to all IFR and participating VFR aircraft. The pilot will be vectored upon request to avoid the observed traffic, provided the aircraft to be vectored is within the airspace under the jurisdiction of the controller. 9. Departing aircraft should inform ATC of their intended destination and/or route of flight and proposed cruising altitude. 10. ATC will normally advise participating VFR aircraft when leaving the geographical limits of the TRSA. Radar service is not automatically terminated with this advisory unless specifically stated by the controller. c. Class C Service. This service provides, in addition to basic radar service, approved separation between IFR and VFR aircraft, and sequencing of VFR arrivals to the primary airport. d. Class B Service. This service provides, in addition to basic radar service, approved separation of aircraft based on IFR, VFR, and/or weight, and sequencing of VFR arrivals to the primary airport(s). e. PILOT RESPONSIBILITY. THESE SERVICES ARE NOT TO BE INTERPRETED AS RELIEVING PILOTS OF THEIR RESPONSIBILITIES TO SEE AND AVOID OTHER TRAFFIC OPERATING IN BASIC VFR WEATHER CONDITIONS, TO ADJUST THEIR OPERATIONS AND FLIGHT PATH AS NECESSARY TO PRECLUDE SERIOUS WAKE ENCOUNTERS, TO MAINTAIN APPROPRIATE TERRAIN AND OBSTRUCTION CLEARANCE, OR TO REMAIN IN WEATHER CONDITIONS EQUAL TO OR BETTER THAN THE MINIMUMS REQUIRED BY 14 CFR SECTION 91.155. WHENEVER COMPLIANCE WITH AN ASSIGNED ROUTE, HEADING AND/OR ALTITUDE IS LIKELY TO COMPROMISE PILOT RESPONSIBILITY RESPECTING TERRAIN AND OBSTRUCTION CLEARANCE, VORTEX EXPOSURE, AND WEATHER MINIMUMS, APPROACH CONTROL SHOULD BE SO ADVISED AND A REVISED CLEARANCE OR INSTRUCTION OBTAINED. f. ATC services for VFR aircraft participating in terminal radar services are dependent on ATC radar. Services for VFR aircraft are not available during periods of a radar outage and are limited during 4−1−14 6/17/21 CENRAP operations. The pilot will be advised when VFR services are limited or not available. NOTE− Class B and Class C airspace are areas of regulated airspace. The absence of ATC radar does not negate the requirement of an ATC clearance to enter Class B airspace or two way radio contact with ATC to enter Class C airspace. 4−1−19. Tower En Route Control (TEC) a. TEC is an ATC program to provide a service to aircraft proceeding to and from metropolitan areas. It links designated Approach Control Areas by a network of identified routes made up of the existing airway structure of the National Airspace System. The FAA initiated an expanded TEC program to include as many facilities as possible. The program’s intent is to provide an overflow resource in the low altitude system which would enhance ATC services. A few facilities have historically allowed turbojets to proceed between certain city pairs, such as Milwaukee and Chicago, via tower en route and these locations may continue this service. However, the expanded TEC program will be applied, generally, for nonturbojet aircraft operating at and below 10,000 feet. The program is entirely within the approach control airspace of multiple terminal facilities. Essentially, it is for relatively short flights. Participating pilots are encouraged to use TEC for flights of two hours duration or less. If longer flights are planned, extensive coordination may be required within the multiple complex which could result in unanticipated delays. b. Pilots requesting TEC are subject to the same delay factor at the destination airport as other aircraft in the ATC system. In addition, departure and en route delays may occur depending upon individual facility workload. When a major metropolitan airport is incurring significant delays, pilots in the TEC program may want to consider an alternative airport experiencing no delay. c. There are no unique requirements upon pilots to use the TEC program. Normal flight plan filing procedures will ensure proper flight plan processing. Pilots should include the acronym “TEC” in the remarks section of the flight plan when requesting tower en route control. d. All approach controls in the system may not operate up to the maximum TEC altitude of 10,000 feet. IFR flight may be planned to any Services Available to Pilots 6/17/21 satellite airport in proximity to the major primary airport via the same routing. 4−1−20. Transponder and ADS−B Out Operation a. General 1. Pilots should be aware that proper application of transponder and ADS−B operating procedures will provide both VFR and IFR aircraft with a higher degree of safety while operating on the ground and airborne. Transponder/ADS−B panel designs differ; therefore, a pilot should be thoroughly familiar with the operation of their particular equipment to maximize its full potential. ADS−B Out, and transponders with altitude reporting mode turned ON (Mode C or S), substantially increase the capability of surveillance systems to see an aircraft. This provides air traffic controllers, as well as pilots of suitably equipped aircraft (TCAS and ADS−B In), increased situational awareness and the ability to identify potential traffic conflicts. Even VFR pilots who are not in contact with ATC will be afforded greater protection from IFR aircraft and VFR aircraft that are receiving traffic advisories. Nevertheless, pilots should never relax their visual scanning for other aircraft. 2. Air Traffic Control Radar Beacon System (ATCRBS) is similar to and compatible with military coded radar beacon equipment. Civil Mode A is identical to military Mode 3. 3. Transponder and ADS-B operations on the ground. Civil and military aircraft should operate with the transponder in the altitude reporting mode (consult the aircraft’s flight manual to determine the specific transponder position to enable altitude reporting) and ADS−B Out transmissions enabled at all airports, any time the aircraft is positioned on any portion of the airport movement area. This includes all defined taxiways and runways. Pilots must pay particular attention to ATIS and airport diagram notations, General Notes (included on airport charts), and comply with directions pertaining to transponder and ADS-B usage. Generally, these directions are: (a) Departures. Select the transponder mode which allows altitude reporting and enable ADS-B during pushback or taxi-out from parking spot. Select TA or TA/RA (if equipped with TCAS) when taking the active runway. Services Available to Pilots AIM (b) Arrivals. If TCAS equipped, deselect TA or TA/RA upon leaving the active runway, but continue transponder and ADS−B transmissions in the altitude reporting mode. Select STBY or OFF for transponder and ADS−B upon arriving at the aircraft’s parking spot or gate. 4. Transponder and ADS-B Operations While Airborne. (a) Unless otherwise requested by ATC, aircraft equipped with an ATC transponder maintained in accordance with 14 CFR Section 91.413 MUST operate with this equipment on the appropriate Mode 3/A code, or other code as assigned by ATC, and with altitude reporting enabled whenever in controlled airspace. If practicable, aircraft SHOULD operate with the transponder enabled in uncontrolled airspace. (b) Aircraft equipped with ADS−B Out MUST operate with this equipment in the transmit mode at all times, unless otherwise requested by ATC. (c) When participating in a VFR formation flight that is not receiving ATC services, only the lead aircraft should operate their transponder and ADS−B Out. All other aircraft should disable transponder and ADS−B transmissions once established within the formation. NOTE− If the formation flight is receiving ATC services, pilots can expect ATC to direct all non−lead aircraft to STOP SQUAWK, and should not do so until instructed. 5. A pilot on an IFR flight who elects to cancel the IFR flight plan prior to reaching their destination, should adjust the transponder/ADS−B according to VFR operations. 6. If entering a U.S. OFFSHORE AIRSPACE AREA from outside the U.S., the pilot should advise on first radio contact with a U.S. radar ATC facility that such equipment is available by adding “transponder” or “ADS−B” (if equipped) to the aircraft identification. 7. It should be noted by all users of ATC transponders and ADS−B Out systems that the surveillance coverage they can expect is limited to “line of sight” with ground radar and ADS−B radio sites. Low altitude or aircraft antenna shielding by the aircraft itself may result in reduced range or loss of aircraft contact. Though ADS−B often provides 4−1−15 AIM superior reception at low altitudes, poor coverage from any surveillance system can be improved by climbing to a higher altitude. NOTE− Pilots should refer to AIM, Paragraph 4−5−7, Automatic Dependent Surveillance − Broadcast (ADS−B) Services, for a complete description of operating limitations and procedures. b. Transponder/ADS−B Code Designation 1. For ATC to utilize one of the 4096 discrete codes, a four−digit code designation will be used; for example, code 2102 will be expressed as “TWO ONE ZERO TWO.” NOTE− Circumstances may occasionally require ATC to assign a non−discrete code; i.e., a code ending in “00.” REFERENCE− FAA Order JO 7110.66, National Beacon Code Allocation Plan. c. Automatic Altitude Reporting 1. Most transponders (Modes C and S) and all ADS−B Out systems are capable of automatic altitude reporting. This system converts aircraft altitude in 100−foot increments to coded digital information that is transmitted to the appropriate surveillance facility as well as to ADS−B In and TCAS systems. 2. Adjust the transponder/ADS−B to reply on the Mode 3/A code specified by ATC and with altitude reporting enabled, unless otherwise directed by ATC or unless the altitude reporting equipment has not been tested and calibrated as required by 14 CFR Section 91.217. If deactivation is required by ATC, turn off the altitude reporting feature of your transponder/ADS−B. An instruction by ATC to “STOP ALTITUDE SQUAWK, ALTITUDE DIFFERS BY (number of feet) FEET,” may be an indication that the transmitted altitude information is incorrect, or that the aircraft’s altimeter setting is incorrect. While an incorrect altimeter setting has no effect on the transmitted altitude information, it will cause the aircraft to fly at a true altitude different from the assigned altitude. When a controller indicates that an altitude readout is invalid, the pilot should verify that the aircraft altimeter is set correctly. NOTE− Altitude encoders are preset at standard atmospheric pressure. Local altimeter correction is applied by the surveillance facility before the altitude information is presented to ATC. 4−1−16 6/17/21 3. Pilots should report exact altitude or flight level to the nearest hundred foot increment when establishing initial contact with an ATC facility. Exact altitude or flight level reports on initial contact provide ATC with information that is required prior to using automatically reported altitude information for separation purposes. This will significantly reduce altitude verification requests. d. IDENT Feature Transponder/ADS−B Out equipment must be operated only as specified by ATC. Activate the “IDENT” feature only when requested by ATC. e. Code Changes 1. When making routine code changes, pilots should avoid inadvertent selection of Codes 7500, 7600 or 7700 thereby causing momentary false alarms at automated ground facilities. For example, when switching from Code 2700 to Code 7200, switch first to 2200 then to 7200, NOT to 7700 and then 7200. This procedure applies to nondiscrete Code 7500 and all discrete codes in the 7600 and 7700 series (i.e., 7600−7677, 7700−7777) which will trigger special indicators in automated facilities. Only nondiscrete Code 7500 will be decoded as the hijack code. 2. Under no circumstances should a pilot of a civil aircraft operate the transponder on Code 7777. This code is reserved for military interceptor operations. 3. Military pilots operating VFR or IFR within restricted/warning areas should adjust their transponders to Code 4000 unless another code has been assigned by ATC. f. Mode C Transponder and ADS−B Out Requirements 1. Specific details concerning requirements to carry and operate Mode C transponders and ADS−B Out, as well as exceptions and ATC authorized deviations from those requirements, are found in 14 CFR Sections 91.215, 91.225, and 99.13. 2. In general, the CFRs require aircraft to be equipped with an operable Mode C transponder and ADS−B Out when operating: (a) In Class A, Class B, or Class C airspace areas; (b) Above the ceiling and within the lateral boundaries of Class B or Class C airspace up to 10,000 feet MSL; Services Available to Pilots 12/2/21 6/17/21 (c) Class E airspace at and above 10,000 feet MSL within the 48 contiguous states and the District of Columbia, excluding the airspace at and below 2,500 feet AGL; (d) Within 30 miles of a Class B airspace primary airport, below 10,000 feet MSL (commonly referred to as the “Mode C Veil”); (e) For ADS−B Out: Class E airspace at and above 3,000 feet MSL over the Gulf of Mexico from the coastline of the United States out to 12 nautical miles. NOTE− The airspace described in (e) above is specified in 14 CFR § 91.225 for ADS−B Out requirements. However, 14 CFR § 91.215 does not include this airspace for ATC transponder requirements. (f) Transponder and ADS−B Out requirements do not apply to any aircraft that was not originally certificated with an electrical system, or that has not subsequently been certified with such a system installed, including balloons and gliders. These aircraft may conduct operations without a transponder or ADS−B Out when operating: (1) Outside any Class B or Class C airspace area; and (2) Below the altitude of the ceiling of a Class B or Class C airspace area designated for an airport, or 10,000 feet MSL, whichever is lower. 3. 14 CFR Section 99.13 requires all aircraft flying into, within, or across the contiguous U.S. ADIZ be equipped with a Mode C or Mode S transponder. Balloons, gliders and aircraft not equipped with an engine−driven electrical system are excepted from this requirement. REFERENCE− AIM, Chapter 5, Section 6, National Security and Interception Procedures. 4. Pilots must ensure that their aircraft transponder/ADS−B is operating on an appropriate ATC−assigned VFR/IFR code with altitude reporting enabled when operating in such airspace. If in doubt about the operational status of either feature of your transponder while airborne, contact the nearest ATC facility or FSS and they will advise you what facility you should contact for determining the status of your equipment. 5. In−flight requests for “immediate” deviation from the transponder requirements may be approved Services Available to Pilots AIM by controllers only for failed equipment, and only when the flight will continue IFR or when weather conditions prevent VFR descent and continued VFR flight in airspace not affected by the CFRs. All other requests for deviation should be made at least 1 hour before the proposed operation by contacting the nearest Flight Service or Air Traffic facility in person or by telephone. The nearest ARTCC will normally be the controlling agency and is responsible for coordinating requests involving deviations in other ARTCC areas. 6. In−flight requests for “immediate” deviation from the ADS−B Out requirements may be approved by ATC only for failed equipment, and may be accommodated based on workload, alternate surveillance availability, or other factors. All other requests for deviation must be made at least 1 hour before the proposed operation, following the procedures contained in Advisory Circular (AC) 90−114, Automatic Dependent Surveillance−Broadcast Operations. g. Transponder/ADS−B Operation Under Visual Flight Rules (VFR) 1. Unless otherwise instructed by an ATC facility, adjust transponder/ADS−B to reply on Mode 3/A Code 1200 regardless of altitude. NOTE− 1. Firefighting aircraft not in contact with ATC may squawk 1255 in lieu of 1200 while en route to, from, or within the designated firefighting area(s). 2. VFR aircraft flying authorized SAR missions for the USAF or USCG may be advised to squawk 1277 in lieu of 1200 while en route to, from, or within the designated search area. 3. VFR gliders should squawk 1202 in lieu of 1200. REFERENCE− FAA Order JO 7110.66, National Beacon Code Allocation Plan. 2. When required to operate their transponder/ ADS−B, pilots must always operate that equipment with altitude reporting enabled, unless otherwise instructed by ATC or unless the installed equipment has not been tested and calibrated as required by 14 CFR Section 91.217. If deactivation is required, turn off altitude reporting. 3. When participating in a VFR formation flight that is not receiving ATC services, only the lead aircraft should operate their transponder and ADS−B Out. All other aircraft should disable transponder and ADS−B transmissions once established within the formation. 4−1−17 7110.65R CHG 2 AIM AIM NOTE− If the formation flight is receiving ATC services, pilots can expect ATC to direct all non−lead aircraft to STOP SQUAWK, and should not do so until instructed. h. Cooperative Surveillance Phraseology Air traffic controllers, both civil and military, will use the following phraseology when referring to operation of cooperative ATC surveillance equipment. Except as noted, the following ATC instructions do not apply to military transponders operating in other than Mode 3/A/C/S. 1. SQUAWK (number). Operate radar beacon transponder/ADS−B on designated code with altitude reporting enabled. 2. IDENT. Engage the “IDENT” feature (military I/P) of the transponder/ADS−B. 3. SQUAWK (number) AND IDENT. Operate transponder/ADS−B on specified code with altitude reporting enabled, and engage the “IDENT” (military I/P) feature. 4. SQUAWK STANDBY. Switch transponder/ADS−B to standby position. 5. SQUAWK NORMAL. Resume normal transponder/ADS−B operation on previously assigned code. (Used after “SQUAWK STANDBY,” or by military after specific transponder tests). 6. SQUAWK ALTITUDE. Activate Mode C with automatic altitude reporting. 7. STOP ALTITUDE SQUAWK. Turn off automatic altitude reporting. 8. STOP SQUAWK (Mode in use). Stop transponder and ADS−B Out transmissions, or switch off only specified mode of the aircraft transponder (military). 9. SQUAWK MAYDAY. Operate transponder/ADS−B in the emergency position (Mode A Code 7700 for civil transponder. Mode 3 Code 7700 and emergency feature for military transponder.) 10. SQUAWK VFR. Operate radar beacon transponder/ADS−B on Code 1200 in the Mode A/3, or other appropriate VFR code, with altitude reporting enabled. 4−1−18 3/15/07 12/2/21 6/17/21 4−1−21. Airport Reservation Operations and Special Traffic Management Programs This section describes procedures for obtaining required airport reservations at airports designated by the FAA and for airports operating under Special Traffic Management Programs. a. Slot Controlled Airports. 1. The FAA may adopt rules to require advance operations for unscheduled operations at certain airports. In addition to the information in the rules adopted by the FAA, a listing of the airports and relevant information will be maintained on the FAA website listed below. 2. The FAA has established an Airport Reservation Office (ARO) to receive and process reservations for unscheduled flights at the slot controlled airports. The ARO uses the Enhanced Computer Voice Reservation System (e−CVRS) to allocate reservations. Reservations will be available beginning 72 hours in advance of the operation at the slot controlled airport. Standby lists are not maintained. Flights with declared emergencies do not require reservations. Refer to the website or touch−tone phone interface for the current listing of slot controlled airports, limitations, and reservation procedures. NOTE− The web interface/telephone numbers to obtain a reservation for unscheduled operations at a slot controlled airport are: 1. http://www.fly.faa.gov/ecvrs. 2. Touch−tone: 1−800−875−9694 3. Trouble number: 540−422−4246. 3. For more detailed information on operations and reservation procedures at a Slot Controlled Airport, please see 14 CFR Part 93, Subpart K – High Density Traffic Airports. b. Special Traffic Management Programs (STMP). 1. Special procedures may be established when a location requires special traffic handling to accommodate above normal traffic demand (for example, the Indianapolis 500, Super Bowl, etc.) or reduced airport capacity (for example, airport runway/taxiway closures for airport construction). The special procedures may remain in effect until the problem has been resolved or until local traffic Services Available to Pilots 12/2/21 6/17/21 management procedures can handle the situation and a need for special handling no longer exists. 2. There will be two methods available for obtaining slot reservations through the ATCSCC: the web interface and the touch−tone interface. If these methods are used, a NOTAM will be issued relaying the website address and toll free telephone number. Be sure to check current NOTAMs to determine: what airports are included in the STMP, the dates and times reservations are required, the time limits for reservation requests, the point of contact for reservations, and any other instructions. NOTE− The telephone numbers/web address to obtain a STMP slot are: 1.Touch−tone interface: 1−800−875−9755. 2. Web interface: www.fly.faa.gov. 3. Trouble number: 540−422−4246. c. Users may contact the ARO at (540) 422−4246 if they have a problem making a reservation or have a question concerning the slot controlled airport/ STMP regulations or procedures. d. Making Reservations. 1. Internet Users. Detailed information and User Instruction Guides for using the Web interface to the reservation systems are available on the websites for the slot controlled airports (e−CVRS), http://www.fly.faa.gov/ecvrs; and STMPs (e−STMP), http://www.fly.faa.gov/estmp. 4−1−22. Requests for Waivers and Authorizations from Title 14, Code of Federal Regulations (14 CFR) a. Requests for a Certificate of Waiver or Services Available to Pilots AIM Authorization (FAA Form 7711−2), or requests for renewal of a waiver or authorization, may be accepted by any FAA facility and will be forwarded, if necessary, to the appropriate office having waiver authority. b. The grant of a Certificate of Waiver or Authorization from 14 CFR constitutes relief from specific regulations, to the degree and for the period of time specified in the certificate, and does not waive any state law or local ordinance. Should the proposed operations conflict with any state law or local ordinance, or require permission of local authorities or property owners, it is the applicant’s responsibility to resolve the matter. The holder of a waiver is responsible for compliance with the terms of the waiver and its provisions. c. A waiver may be canceled at any time by the Administrator, the person authorized to grant the waiver, or the representative designated to monitor a specific operation. In such case either written notice of cancellation, or written confirmation of a verbal cancellation will be provided to the holder. 4−1−23. Weather Systems Processor The Weather Systems Processor (WSP) was developed for use in the National Airspace System to provide weather processor enhancements to selected Airport Surveillance Radar (ASR)−9 facilities. The WSP provides Air Traffic with warnings of hazardous wind shear and microbursts. The WSP also provides users with terminal area 6−level weather, storm cell locations and movement, as well as the location and predicted future position and intensity of wind shifts that may affect airport operations. 4−1−19 6/17/21 AIM Section 2. Radio Communications Phraseology and Techniques 4−2−1. General a. Radio communications are a critical link in the ATC system. The link can be a strong bond between pilot and controller or it can be broken with surprising speed and disastrous results. Discussion herein provides basic procedures for new pilots and also highlights safe operating concepts for all pilots. b. The single, most important thought in pilotcontroller communications is understanding. It is essential, therefore, that pilots acknowledge each radio communication with ATC by using the appropriate aircraft call sign. Brevity is important, and contacts should be kept as brief as possible, but controllers must know what you want to do before they can properly carry out their control duties. And you, the pilot, must know exactly what the controller wants you to do. Since concise phraseology may not always be adequate, use whatever words are necessary to get your message across. Pilots are to maintain vigilance in monitoring air traffic control radio communications frequencies for potential traffic conflicts with their aircraft especially when operating on an active runway and/or when conducting a final approach to landing. c. All pilots will find the Pilot/Controller Glossary very helpful in learning what certain words or phrases mean. Good phraseology enhances safety and is the mark of a professional pilot. Jargon, chatter, and “CB” slang have no place in ATC communications. The Pilot/Controller Glossary is the same glossary used in FAA Order JO 7110.65, Air Traffic Control. We recommend that it be studied and reviewed from time to time to sharpen your communication skills. 4−2−2. Radio Technique a. Listen before you transmit. Many times you can get the information you want through ATIS or by monitoring the frequency. Except for a few situations where some frequency overlap occurs, if you hear someone else talking, the keying of your transmitter will be futile and you will probably jam their receivers causing them to repeat their call. If you have Radio Communications Phraseology just changed frequencies, pause, listen, and make sure the frequency is clear. b. Think before keying your transmitter. Know what you want to say and if it is lengthy; e.g., a flight plan or IFR position report, jot it down. c. The microphone should be very close to your lips and after pressing the mike button, a slight pause may be necessary to be sure the first word is transmitted. Speak in a normal, conversational tone. d. When you release the button, wait a few seconds before calling again. The controller or FSS specialist may be jotting down your number, looking for your flight plan, transmitting on a different frequency, or selecting the transmitter for your frequency. e. Be alert to the sounds or the lack of sounds in your receiver. Check your volume, recheck your frequency, and make sure that your microphone is not stuck in the transmit position. Frequency blockage can, and has, occurred for extended periods of time due to unintentional transmitter operation. This type of interference is commonly referred to as a “stuck mike,” and controllers may refer to it in this manner when attempting to assign an alternate frequency. If the assigned frequency is completely blocked by this type of interference, use the procedures described for en route IFR radio frequency outage to establish or reestablish communications with ATC. f. Be sure that you are within the performance range of your radio equipment and the ground station equipment. Remote radio sites do not always transmit and receive on all of a facility’s available frequencies, particularly with regard to VOR sites where you can hear but not reach a ground station’s receiver. Remember that higher altitudes increase the range of VHF “line of sight” communications. 4−2−3. Contact Procedures a. Initial Contact. 1. The terms initial contact or initial callup means the first radio call you make to a given facility or the first call to a different controller or FSS specialist within a facility. Use the following format: 4−2−1 AIM 6/17/21 (a) Name of the facility being called; (b) Your full aircraft identification as filed in the flight plan or as discussed in paragraph 4−2−4, Aircraft Call Signs; (c) When operating on an airport surface, state your position. (d) The type of message to follow or your request if it is short; and (e) The word “Over” if required. EXAMPLE− 1. “New York Radio, Mooney Three One One Echo.” 2. “Columbia Ground, Cessna Three One Six Zero Foxtrot, south ramp, I−F−R Memphis.” 3. “Miami Center, Baron Five Six Three Hotel, request V−F−R traffic advisories.” 2. Many FSSs are equipped with Remote Communications Outlets (RCOs) and can transmit on the same frequency at more than one location. The frequencies available at specific locations are indicated on charts above FSS communications boxes. To enable the specialist to utilize the correct transmitter, advise the location and the frequency on which you expect a reply. EXAMPLE− St. Louis FSS can transmit on frequency 122.3 at either Farmington, Missouri, or Decatur, Illinois, if you are in the vicinity of Decatur, your callup should be “Saint Louis radio, Piper Six Niner Six Yankee, receiving Decatur One Two Two Point Three.” 3. If radio reception is reasonably assured, inclusion of your request, your position or altitude, and the phrase “(ATIS) Information Charlie received” in the initial contact helps decrease radio frequency congestion. Use discretion; do not overload the controller with information unneeded or superfluous. If you do not get a response from the ground station, recheck your radios or use another transmitter, but keep the next contact short. EXAMPLE− “Atlanta Center, Duke Four One Romeo, request V−F−R traffic advisories, Twenty Northwest Rome, seven thousand five hundred, over.” b. Initial Contact When Your Transmitting and Receiving Frequencies are Different. 1. If you are attempting to establish contact with a ground station and you are receiving on a different frequency than that transmitted, indicate the VOR name or the frequency on which you expect a reply. 4−2−2 Most FSSs and control facilities can transmit on several VOR stations in the area. Use the appropriate FSS call sign as indicated on charts. EXAMPLE− New York FSS transmits on the Kennedy, the Hampton, and the Calverton VORTACs. If you are in the Calverton area, your callup should be “New York radio, Cessna Three One Six Zero Foxtrot, receiving Calverton V−O−R, over.” 2. If the chart indicates FSS frequencies above the VORTAC or in the FSS communications boxes, transmit or receive on those frequencies nearest your location. 3. When unable to establish contact and you wish to call any ground station, use the phrase “ANY RADIO (tower) (station), GIVE CESSNA THREE ONE SIX ZERO FOXTROT A CALL ON (frequency) OR (V−O−R).” If an emergency exists or you need assistance, so state. c. Subsequent Contacts and Responses to Callup from a Ground Facility. Use the same format as used for the initial contact except you should state your message or request with the callup in one transmission. The ground station name and the word “Over” may be omitted if the message requires an obvious reply and there is no possibility for misunderstandings. You should acknowledge all callups or clearances unless the controller or FSS specialist advises otherwise. There are some occasions when controllers must issue time-critical instructions to other aircraft, and they may be in a position to observe your response, either visually or on radar. If the situation demands your response, take appropriate action or immediately advise the facility of any problem. Acknowledge with your aircraft identification, either at the beginning or at the end of your transmission, and one of the words “Wilco,” “Roger,” “Affirmative,” “Negative,” or other appropriate remarks; e.g., “PIPER TWO ONE FOUR LIMA, ROGER.” If you have been receiving services; e.g., VFR traffic advisories and you are leaving the area or changing frequencies, advise the ATC facility and terminate contact. d. Acknowledgement of Frequency Changes. 1. When advised by ATC to change frequencies, acknowledge the instruction. If you select the new frequency without an acknowledgement, the controller’s workload is increased because there is no way of knowing whether you received the instruction or have had radio communications failure. Radio Communications Phraseology 6/17/21 2. At times, a controller/specialist may be working a sector with multiple frequency assignments. In order to eliminate unnecessary verbiage and to free the controller/specialist for higher priority transmissions, the controller/specialist may request the pilot “(Identification), change to my frequency 134.5.” This phrase should alert the pilot that the controller/specialist is only changing frequencies, not controller/specialist, and that initial callup phraseology may be abbreviated. EXAMPLE− “United Two Twenty−Two on one three four point five” or “one three four point five, United Two Twenty−Two.” e. Compliance with Frequency Changes. When instructed by ATC to change frequencies, select the new frequency as soon as possible unless instructed to make the change at a specific time, fix, or altitude. A delay in making the change could result in an untimely receipt of important information. If you are instructed to make the frequency change at a specific time, fix, or altitude, monitor the frequency you are on until reaching the specified time, fix, or altitudes unless instructed otherwise by ATC. REFERENCE− AIM, Paragraph 5−3−1 , ARTCC Communications 4−2−4. Aircraft Call Signs a. Precautions in the Use of Call Signs. 1. Improper use of call signs can result in pilots executing a clearance intended for another aircraft. Call signs should never be abbreviated on an initial contact or at any time when other aircraft call signs have similar numbers/sounds or identical letters/ number; e.g., Cessna 6132F, Cessna 1622F, Baron 123F, Cherokee 7732F, etc. EXAMPLE− Assume that a controller issues an approach clearance to an aircraft at the bottom of a holding stack and an aircraft with a similar call sign (at the top of the stack) acknowledges the clearance with the last two or three numbers of the aircraft’s call sign. If the aircraft at the bottom of the stack did not hear the clearance and intervene, flight safety would be affected, and there would be no reason for either the controller or pilot to suspect that anything is wrong. This kind of “human factors” error can strike swiftly and is extremely difficult to rectify. 2. Pilots, therefore, must be certain that aircraft identification is complete and clearly identified Radio Communications Phraseology AIM before taking action on an ATC clearance. ATC specialists will not abbreviate call signs of air carrier or other civil aircraft having authorized call signs. ATC specialists may initiate abbreviated call signs of other aircraft by using the prefix and the last three digits/letters of the aircraft identification after communications are established. The pilot may use the abbreviated call sign in subsequent contacts with the ATC specialist. When aware of similar/identical call signs, ATC specialists will take action to minimize errors by emphasizing certain numbers/letters, by repeating the entire call sign, by repeating the prefix, or by asking pilots to use a different call sign temporarily. Pilots should use the phrase “VERIFY CLEARANCE FOR (your complete call sign)” if doubt exists concerning proper identity. 3. Civil aircraft pilots should state the aircraft type, model or manufacturer’s name, followed by the digits/letters of the registration number. When the aircraft manufacturer’s name or model is stated, the prefix “N” is dropped; e.g., Aztec Two Four Six Four Alpha. EXAMPLE− 1. Bonanza Six Five Five Golf. 2. Breezy Six One Three Romeo Experimental (omit “Experimental” after initial contact). 4. Air Taxi or other commercial operators not having FAA authorized call signs should prefix their normal identification with the phonetic word “Tango.” EXAMPLE− Tango Aztec Two Four Six Four Alpha. 5. Air carriers and commuter air carriers having FAA authorized call signs should identify themselves by stating the complete call sign (using group form for the numbers) and the word “super” or “heavy” if appropriate. EXAMPLE− 1. United Twenty−Five Heavy. 2. Midwest Commuter Seven Eleven. 6. Military aircraft use a variety of systems including serial numbers, word call signs, and combinations of letters/numbers. Examples include Army Copter 48931; Air Force 61782; REACH 31792; Pat 157; Air Evac 17652; Navy Golf Alfa Kilo 21; Marine 4 Charlie 36, etc. 4−2−3 7110.65R CHG 2 AIM AIM b. Air Ambulance Flights. Because of the priority afforded air ambulance flights in the ATC system, extreme discretion is necessary when using the term “MEDEVAC.” It is only intended for those missions of an urgent medical nature and to be utilized only for that portion of the flight requiring priority handling. It is important for ATC to be aware of a flight’s MEDEVAC status, and it is the pilot’s responsibility to ensure that this information is provided to ATC. 1. To receive priority handling from ATC, the pilot must verbally identify the flight in radio transmissions by stating “MEDEVAC” followed by the FAA authorized call sign (ICAO 3LD, US Special, or local) or the aircraft civil “N” registration numbers/letters. EXAMPLE− If the aircraft identification of the flight indicates DAL51, the pilot states “MEDEVAC Delta Fifty One.” If the aircraft identification of the flight indicates MDSTR1, the pilot states “MEDEVAC Medstar One.” If the aircraft identification of the flight indicates N123G or LN123G, the pilot states “MEDEVAC One Two Three Golf”. 2. If requested by the pilot, ATC will provide additional assistance (e.g., landline notifications) to expedite ground handling of patients, vital organs, or urgently needed medical materials. When possible make these requests to ATC via methods other than through ATC radio frequencies. 3. MEDEVAC flights may include: (a) Civilian air ambulance flights responding to medical emergencies (e.g., first call to an accident scene, carrying patients, organ donors, organs, or other urgently needed lifesaving medical material). (b) Air carrier and air taxi flights responding to medical emergencies. The nature of these medical emergency flights usually concerns the transportation of urgently needed lifesaving medical materials or vital organs, but can include inflight medical emergencies. It is imperative that the company/pilot determine, by the nature/urgency of the specific medical cargo, if priority ATC assistance is required. 4. When filing a flight plan, pilots may include “L” for MEDEVAC with the aircraft registration letters/digits and/or include “MEDEVAC” in Item 11 4−2−4 3/15/07 12/2/21 6/17/21 (Remarks) of the flight plan or Item 18 (Other Information) of an international flight plan. However, ATC will only use these flight plan entries for informational purposes or as a visual indicator. ATC will only provide priority handling when the pilot verbally identifies the “MEDEVAC” status of the flight as described in subparagraph b1 above. NOTE− Civilian air ambulance aircraft operating VFR and without a filed flight plan are eligible for priority handling in accordance with subparagraph b1 above. 5. ATC will also provide priority handling to HOSP and AIR EVAC flights when verbally requested. These aircraft may file “HOSP” or “AIR EVAC” in either Item 11 (Remarks) of the flight plan or Item 18 of an international flight plan. For aircraft identification in radio transmissions, civilian pilots will use normal call signs when filing “HOSP” and military pilots will use the “EVAC” call sign. c. Student Pilots Radio Identification. 1. The FAA desires to help student pilots in acquiring sufficient practical experience in the environment in which they will be required to operate. To receive additional assistance while operating in areas of concentrated air traffic, student pilots need only identify themselves as a student pilot during their initial call to an FAA radio facility. EXAMPLE− Dayton tower, Fleetwing One Two Three Four, student pilot. 2. This special identification will alert FAA ATC personnel and enable them to provide student pilots with such extra assistance and consideration as they may need. It is recommended that student pilots identify themselves as such, on initial contact with each clearance delivery prior to taxiing, ground control, tower, approach and departure control frequency, or FSS contact. 4−2−5. Description of Interchange or Leased Aircraft a. Controllers issue traffic information based on familiarity with airline equipment and color/ markings. When an air carrier dispatches a flight using another company’s equipment and the pilot does not advise the terminal ATC facility, the possible confusion in aircraft identification can compromise safety. b. Pilots flying an “interchange” or “leased” aircraft not bearing the colors/markings of the Radio Communications Phraseology 12/2/21 6/17/21 AIM company operating the aircraft should inform the terminal ATC facility on first contact the name of the operating company and trip number, followed by the company name as displayed on the aircraft, and aircraft type. EXAMPLE− Air Cal Three Eleven, United (interchange/lease), Boeing Seven Two Seven. 4−2−6. Ground Station Call Signs Pilots, when calling a ground station, should begin with the name of the facility being called followed by the type of the facility being called as indicated in TBL 4−2−1. TBL 4−2−1 Calling a Ground Station Facility Airport UNICOM FAA Flight Service Station Airport Traffic Control Tower Clearance Delivery Position (IFR) Ground Control Position in Tower Radar or Nonradar Approach Control Position Radar Departure Control Position FAA Air Route Traffic Control Center Call Sign “Shannon UNICOM” “Chicago Radio” “Augusta Tower” “Dallas Clearance Delivery” “Miami Ground” TBL 4−2−2 Phonetic Alphabet/Morse Code Character Morse Code Telephony Phonic (Pronunciation) A Alfa (AL−FAH) B Bravo (BRAH−VOH) C Charlie (CHAR−LEE) or (SHAR−LEE) D Delta (DELL−TAH) E Echo (ECK−OH) F Foxtrot (FOKS−TROT) G Golf (GOLF) H Hotel (HOH−TEL) I India (IN−DEE−AH) J Juliett (JEW−LEE−ETT) K Kilo (KEY−LOH) L Lima (LEE−MAH) M Mike (MIKE) N November (NO−VEM−BER) O Oscar (OSS−CAH) P Papa (PAH−PAH) Q Quebec (KEH−BECK) R Romeo (ROW−ME−OH) S Sierra (SEE−AIR−RAH) T Tango (TANG−GO) U Uniform (YOU−NEE−FORM) or (OO−NEE−FORM) (VIK−TAH) V Victor W Whiskey (WISS−KEY) X Xray (ECKS−RAY) Y Yankee (YANG−KEY) Z Zulu (ZOO−LOO) 1 One (WUN) 2 Two (TOO) 3 Three (TREE) 4 Four (FOW−ER) 4−2−7. Phonetic Alphabet 5 Five (FIFE) 6 Six (SIX) The International Civil Aviation Organization (ICAO) phonetic alphabet is used by FAA personnel when communications conditions are such that the information cannot be readily received without their use. ATC facilities may also request pilots to use phonetic letter equivalents when aircraft with similar sounding identifications are receiving communications on the same frequency. Pilots should use the phonetic alphabet when identifying their aircraft during initial contact with air traffic control facilities. Additionally, use the phonetic equivalents for single letters and to spell out groups of letters or difficult words during adverse communications conditions. (See TBL 4−2−2.) 7 Seven (SEV−EN) 8 Eight (AIT) 9 Nine (NIN−ER) 0 Zero (ZEE−RO) “Oklahoma City Approach” “St. Louis Departure” “Washington Center” Radio Communications Phraseology 4−2−8. Figures a. Figures indicating hundreds and thousands in round number, as for ceiling heights, and upper wind levels up to 9,900 must be spoken in accordance with the following. EXAMPLE− 1. 500 . . . . . . . . five hundred 2. 4,500 . . . . . . four thousand five hundred 4−2−5 7110.65R CHG 2 AIM AIM b. Numbers above 9,900 must be spoken by separating the digits preceding the word “thousand.” EXAMPLE− 1. 10,000 . . . . . one zero thousand 2. 13,500 . . . . . one three thousand five hundred c. Transmit airway or jet route numbers as follows. EXAMPLE− 1. V12 . . . . . . . Victor Twelve 2. J533 . . . . . . . J Five Thirty−Three 3/15/07 12/2/21 6/17/21 4. (Magnetic heading) 100 . . . . . heading one zero zero 5. (Wind direction) 220 . . . . . . . . wind two two zero 4−2−11. Speeds The separate digits of the speed followed by the word “KNOTS.” Except, controllers may omit the word “KNOTS” when using speed adjustment procedures; e.g., “REDUCE/INCREASE SPEED TO TWO FIVE ZERO.” d. All other numbers must be transmitted by pronouncing each digit. EXAMPLE− (Speed) 250 . . . . . . . . . . . . . . . . . two five zero knots (Speed) 190 . . . . . . . . . . . . . . . . . one niner zero knots EXAMPLE− 10 . . . . . . . . . . . one zero The separate digits of the Mach Number preceded by “Mach.” e. When a radio frequency contains a decimal point, the decimal point is spoken as “POINT.” EXAMPLE− 122.1 . . . . . . . . . one two two point one NOTE− ICAO procedures require the decimal point be spoken as “DECIMAL.” The FAA will honor such usage by military aircraft and all other aircraft required to use ICAO procedures. 4−2−9. Altitudes and Flight Levels a. Up to but not including 18,000 feet MSL, state the separate digits of the thousands plus the hundreds if appropriate. EXAMPLE− 1. 12,000 . . . . . one two thousand 2. 12,500 . . . . . one two thousand five hundred b. At and above 18,000 feet MSL (FL 180), state the words “flight level” followed by the separate digits of the flight level. EXAMPLE− 1. 190 . . . . . . . . Flight Level One Niner Zero 2. 275 . . . . . . . . Flight Level Two Seven Five 4−2−10. Directions The three digits of bearing, course, heading, or wind direction should always be magnetic. The word “true” must be added when it applies. EXAMPLE− 1. (Magnetic course) 005 . . . . . . zero zero five 2. (True course) 050 . . . . . . . . . . zero five zero true 3. (Magnetic bearing) 360 . . . . . three six zero 4−2−6 EXAMPLE− (Mach number) 1.5 . . . . . . . . . . . . Mach one point five (Mach number) 0.64 . . . . . . . . . . . Mach point six four (Mach number) 0.7 . . . . . . . . . . . . Mach point seven 4−2−12. Time a. FAA uses Coordinated Universal Time (UTC) for all operations. The word “local” or the time zone equivalent must be used to denote local when local time is given during radio and telephone communications. The term “Zulu” may be used to denote UTC. EXAMPLE− 0920 UTC . . . . . zero niner two zero, zero one two zero pacific or local, or one twenty AM b. To convert from Standard Time to Coordinated Universal Time: TBL 4−2−3 Standard Time to Coordinated Universal Time Eastern Standard Time . . . . . . . . . Central Standard Time . . . . . . . . . Mountain Standard Time . . . . . . . Pacific Standard Time . . . . . . . . . Alaska Standard Time . . . . . . . . . Hawaii Standard Time . . . . . . . . . Add 5 hours Add 6 hours Add 7 hours Add 8 hours Add 9 hours Add 10 hours NOTE− For daylight time, subtract 1 hour. c. A reference may be made to local daylight or standard time utilizing the 24−hour clock system. The hour is indicated by the first two figures and the minutes by the last two figures. EXAMPLE− 0000 . . . . . . . . . . . . . . . . . . . . . . . zero zero zero zero 0920 . . . . . . . . . . . . . . . . . . . . . . . zero niner two zero Radio Communications Phraseology 12/2/21 6/17/21 d. Time may be stated in minutes only (two figures) in radiotelephone communications when no misunderstanding is likely to occur. e. Current time in use at a station is stated in the nearest quarter minute in order that pilots may use this information for time checks. Fractions of a quarter minute less than 8 seconds are stated as the preceding quarter minute; fractions of a quarter minute of 8 seconds or more are stated as the succeeding quarter minute. EXAMPLE− 0929:05 . . . . . . time, zero niner two niner 0929:10 . . . . . . time, zero niner two niner and one−quarter 4−2−13. Communications with Tower when Aircraft Transmitter or Receiver or Both are Inoperative a. Arriving Aircraft. 1. Receiver inoperative. (a) If you have reason to believe your receiver is inoperative, remain outside or above the Class D surface area until the direction and flow of traffic has been determined; then, advise the tower of your type aircraft, position, altitude, intention to land, and request that you be controlled with light signals. REFERENCE− AIM, Paragraph 4−3−13 , Traffic Control Light Signals (b) When you are approximately 3 to 5 miles from the airport, advise the tower of your position and join the airport traffic pattern. From this point on, watch the tower for light signals. Thereafter, if a complete pattern is made, transmit your position downwind and/or turning base leg. 2. Transmitter inoperative. Remain outside or above the Class D surface area until the direction and flow of traffic has been determined; then, join the airport traffic pattern. Monitor the primary local control frequency as depicted on Sectional Charts for landing or traffic information, and look for a light signal which may be addressed to your aircraft. During hours of daylight, acknowledge tower transmissions or light signals by rocking your wings. At night, acknowledge by blinking the landing or navigation lights. To acknowledge tower transmissions during daylight hours, hovering helicopters will turn in the direction of the controlling facility and flash the landing light. While in flight, helicopters Radio Communications Phraseology AIM should show their acknowledgement of receiving a transmission by making shallow banks in opposite directions. At night, helicopters will acknowledge receipt of transmissions by flashing either the landing or the search light. 3. Transmitter and receiver inoperative. Remain outside or above the Class D surface area until the direction and flow of traffic has been determined; then, join the airport traffic pattern and maintain visual contact with the tower to receive light signals. Acknowledge light signals as noted above. b. Departing Aircraft. If you experience radio failure prior to leaving the parking area, make every effort to have the equipment repaired. If you are unable to have the malfunction repaired, call the tower by telephone and request authorization to depart without two-way radio communications. If tower authorization is granted, you will be given departure information and requested to monitor the tower frequency or watch for light signals as appropriate. During daylight hours, acknowledge tower transmissions or light signals by moving the ailerons or rudder. At night, acknowledge by blinking the landing or navigation lights. If radio malfunction occurs after departing the parking area, watch the tower for light signals or monitor tower frequency. REFERENCE− 14 CFR Section 91.125 and 14 CFR Section 91.129. 4−2−14. Communications for VFR Flights a. FSSs and Supplemental Weather Service Locations (SWSL) are allocated frequencies for different functions; for example, in Alaska, certain FSSs provide Local Airport Advisory on 123.6 MHz or other frequencies which can be found in the Chart Supplement U.S. If you are in doubt as to what frequency to use, 122.2 MHz is assigned to the majority of FSSs as a common en route simplex frequency. NOTE− In order to expedite communications, state the frequency being used and the aircraft location during initial callup. EXAMPLE− Dayton radio, November One Two Three Four Five on one two two point two, over Springfield V−O−R, over. b. Certain VOR voice channels are being utilized for recorded broadcasts; for example, ATIS. These services and appropriate frequencies are listed in the Chart Supplement U.S. On VFR flights, pilots are urged to monitor these frequencies. When in contact 4−2−7 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 with a control facility, notify the controller if you plan to leave the frequency to monitor these broadcasts. 4−2−8 Radio Communications Phraseology 6/17/21 AIM Section 3. Airport Operations 4−3−1. General Increased traffic congestion, aircraft in climb and descent attitudes, and pilot preoccupation with cockpit duties are some factors that increase the hazardous accident potential near the airport. The situation is further compounded when the weather is marginal, that is, just meeting VFR requirements. Pilots must be particularly alert when operating in the vicinity of an airport. This section defines some rules, practices, and procedures that pilots should be familiar with and adhere to for safe airport operations. or directed by the tower, pilots of fixed−wing aircraft approaching to land must circle the airport to the left. Pilots approaching to land in a helicopter must avoid the flow of fixed−wing traffic. However, in all instances, an appropriate clearance must be received from the tower before landing. FIG 4−3−1 Components of a Traffic Pattern 4−3−2. Airports with an Operating Control Tower a. When operating at an airport where traffic control is being exercised by a control tower, pilots are required to maintain two−way radio contact with the tower while operating within the Class B, Class C, and Class D surface area unless the tower authorizes otherwise. Initial callup should be made about 15 miles from the airport. Unless there is a good reason to leave the tower frequency before exiting the Class B, Class C, and Class D surface areas, it is a good operating practice to remain on the tower frequency for the purpose of receiving traffic information. In the interest of reducing tower frequency congestion, pilots are reminded that it is not necessary to request permission to leave the tower frequency once outside of Class B, Class C, and Class D surface areas. Not all airports with an operating control tower will have Class D airspace. These airports do not have weather reporting which is a requirement for surface based controlled airspace, previously known as a control zone. The controlled airspace over these airports will normally begin at 700 feet or 1,200 feet above ground level and can be determined from the visual aeronautical charts. Pilots are expected to use good operating practices and communicate with the control tower as described in this section. b. When necessary, the tower controller will issue clearances or other information for aircraft to generally follow the desired flight path (traffic patterns) when flying in Class B, Class C, and Class D surface areas and the proper taxi routes when operating on the ground. If not otherwise authorized Airport Operations NOTE− This diagram is intended only to illustrate terminology used in identifying various components of a traffic pattern. It should not be used as a reference or guide on how to enter a traffic pattern. c. The following terminology for the various components of a traffic pattern has been adopted as standard for use by control towers and pilots (See FIG 4−3−1): 1. Upwind leg. A flight path parallel to the landing runway in the direction of landing. 2. Crosswind leg. A flight path at right angles to the landing runway off its takeoff end. 3. Downwind leg. A flight path parallel to the landing runway in the opposite direction of landing. 4. Base leg. A flight path at right angles to the landing runway off its approach end and extending from the downwind leg to the intersection of the extended runway centerline. 5. Final approach. A flight path in the direction of landing along the extended runway centerline from the base leg to the runway. 6. Departure. The flight path which begins after takeoff and continues straight ahead along the extended runway centerline. The departure climb continues until reaching a point at least 1/2 mile 4−3−1 AIM beyond the departure end of the runway and within 300 feet of the traffic pattern altitude. d. Many towers are equipped with a tower radar display. The radar uses are intended to enhance the effectiveness and efficiency of the local control, or tower, position. They are not intended to provide radar services or benefits to pilots except as they may accrue through a more efficient tower operation. The four basic uses are: 1. To determine an aircraft’s exact location. This is accomplished by radar identifying the VFR aircraft through any of the techniques available to a radar position, such as having the aircraft squawk ident. Once identified, the aircraft’s position and spatial relationship to other aircraft can be quickly determined, and standard instructions regarding VFR operation in Class B, Class C, and Class D surface areas will be issued. Once initial radar identification of a VFR aircraft has been established and the appropriate instructions have been issued, radar monitoring may be discontinued; the reason being that the local controller’s primary means of surveillance in VFR conditions is visually scanning the airport and local area. 2. To provide radar traffic advisories. Radar traffic advisories may be provided to the extent that the local controller is able to monitor the radar display. Local control has primary control responsibilities to the aircraft operating on the runways, which will normally supersede radar monitoring duties. 3. To provide a direction or suggested heading. The local controller may provide pilots flying VFR with generalized instructions which will facilitate operations; e.g., “PROCEED SOUTHWESTBOUND, ENTER A RIGHT DOWNWIND RUNWAY THREE ZERO,” or provide a suggested heading to establish radar identification or as an advisory aid to navigation; e.g., “SUGGESTED HEADING TWO TWO ZERO, FOR RADAR IDENTIFICATION.” In both cases, the instructions are advisory aids to the pilot flying VFR and are not radar vectors. NOTE− Pilots have complete discretion regarding acceptance of the suggested headings or directions and have sole responsibility for seeing and avoiding other aircraft. 4. To provide information and instructions to aircraft operating within Class B, Class C, and 4−3−2 6/17/21 Class D surface areas. In an example of this situation, the local controller would use the radar to advise a pilot on an extended downwind when to turn base leg. NOTE− The above tower radar applications are intended to augment the standard functions of the local control position. There is no controller requirement to maintain constant radar identification. In fact, such a requirement could compromise the local controller’s ability to visually scan the airport and local area to meet FAA responsibilities to the aircraft operating on the runways and within the Class B, Class C, and Class D surface areas. Normally, pilots will not be advised of being in radar contact since that continued status cannot be guaranteed and since the purpose of the radar identification is not to establish a link for the provision of radar services. e. A few of the radar equipped towers are authorized to use the radar to ensure separation between aircraft in specific situations, while still others may function as limited radar approach controls. The various radar uses are strictly a function of FAA operational need. The facilities may be indistinguishable to pilots since they are all referred to as tower and no publication lists the degree of radar use. Therefore, when in communication with a tower controller who may have radar available, do not assume that constant radar monitoring and complete ATC radar services are being provided. 4−3−3. Traffic Patterns a. It is recommended that aircraft enter the airport traffic pattern at one of the following altitudes listed below. These altitudes should be maintained unless another traffic pattern altitude is published in the Chart Supplement U.S. or unless otherwise required by the applicable distance from cloud criteria (14 CFR Section 91.155). (See FIG 4−3−2 and FIG 4−3−3): 1. Propeller−driven aircraft enter the traffic pattern at 1,000 feet above ground level (AGL). 2. Large and turbine−powered aircraft enter the traffic pattern at an altitude of not less than 1,500 feet AGL or 500 feet above the established pattern altitude. 3. Helicopters operating in the traffic pattern may fly a pattern similar to the fixed−wing aircraft pattern, but at a lower altitude (500 AGL) and closer to the runway. This pattern may be on the opposite side of the runway from fixed−wing traffic when Airport Operations 6/17/21 airspeed requires or for practice power−off landings (autorotation) and if local policy permits. Landings not to the runway must avoid the flow of fixed wing traffic. b. A pilot may vary the size of the traffic pattern depending on the aircraft’s performance characteristics. Pilots of en route aircraft should be constantly alert for aircraft in traffic patterns and avoid these areas whenever possible. c. Unless otherwise indicated, all turns in the traffic pattern must be made to the left, except for helicopters, as applicable. d. On Sectional, Aeronautical, and VFR Terminal Area Charts, right traffic patterns are indicated at public−use and joint−use airports with the abbreviation “RP” (for Right Pattern), followed by the appropriate runway number(s) at the bottom of the airport data block. EXAMPLE− RP 9, 18, 22R Airport Operations AIM NOTE− 1. Pilots are encouraged to use the standard traffic pattern. However, those pilots who choose to execute a straight−in approach, maneuvering for and execution of the approach should not disrupt the flow of arriving and departing traffic. Likewise, pilots operating in the traffic pattern should be alert at all times for aircraft executing straight−in approaches. REFERENCE− AC 90−66B, Non−Towered Airport Flight Operations 2. *RP indicates special conditions exist and refers pilots to the Chart Supplement U.S. 3. Right traffic patterns are not shown at airports with full−time control towers. e. Wind conditions affect all airplanes in varying degrees. Figure 4-3-4 is an example of a chart used to determine the headwind, crosswind, and tailwind components based on wind direction and velocity relative to the runway. Pilots should refer to similar information provided by the aircraft manufacturer when determining these wind components. 4−3−3 AIM 6/17/21 FIG 4−3−2 Traffic Pattern Operations Single Runway EXAMPLE− Key to traffic pattern operations 1. Enter pattern in level flight, abeam the midpoint of the runway, at pattern altitude. 2. Maintain pattern altitude until abeam approach end of the landing runway on downwind leg. 3. Complete turn to final at least 1/4 mile from the runway. 4. Continue straight ahead until beyond departure end of 4−3−4 runway. 5. If remaining in the traffic pattern, commence turn to crosswind leg beyond the departure end of the runway within 300 feet of pattern altitude. 6. If departing the traffic pattern, continue straight out, or exit with a 45 degree turn (to the left when in a left−hand traffic pattern; to the right when in a right−hand traffic pattern) beyond the departure end of the runway, after reaching pattern altitude. Airport Operations 6/17/21 AIM FIG 4−3−3 Traffic Pattern Operations Parallel Runways EXAMPLE− Key to traffic pattern operations crosswind leg beyond the departure end of the runway within 300 feet of pattern altitude. 1. Enter pattern in level flight, abeam the midpoint of the runway, at pattern altitude. 6. If departing the traffic pattern, continue straight out, or exit with a 45 degree turn (to the left when in a left−hand traffic pattern; to the right when in a right−hand traffic pattern) beyond the departure end of the runway, after reaching pattern altitude. 2. Maintain pattern altitude until abeam approach end of the landing runway on downwind leg. 3. Complete turn to final at least 1/4 mile from the runway. 4. Continue straight ahead until beyond departure end of runway. 5. If remaining in the traffic pattern, commence turn to Airport Operations 7. Do not overshoot final or continue on a track which will penetrate the final approach of the parallel runway. 8. Do not continue on a track which will penetrate the departure path of the parallel runway. 4−3−5 AIM 6/17/21 FIG 4−3−4 Headwind/Tailwind/Crosswind Component Calculator 4−3−6 Airport Operations 6/17/21 4−3−4. Visual Indicators at Airports Without an Operating Control Tower a. At those airports without an operating control tower, a segmented circle visual indicator system, if installed, is designed to provide traffic pattern information. REFERENCE− AIM, Paragraph 4−1−9 , Traffic Advisory Practices at Airports Without Operating Control Towers b. The segmented circle system consists of the following components: 1. The segmented circle. Located in a position affording maximum visibility to pilots in the air and on the ground and providing a centralized location for other elements of the system. 2. The wind direction indicator. A wind cone, wind sock, or wind tee installed near the operational runway to indicate wind direction. The large end of the wind cone/wind sock points into the wind as does the large end (cross bar) of the wind tee. In lieu of a tetrahedron and where a wind sock or wind cone is collocated with a wind tee, the wind tee may be manually aligned with the runway in use to indicate landing direction. These signaling devices may be located in the center of the segmented circle and may be lighted for night use. Pilots are cautioned against using a tetrahedron to indicate wind direction. 3. The landing direction indicator. A tetrahedron is installed when conditions at the airport warrant its use. It may be used to indicate the direction of landings and takeoffs. A tetrahedron may be located at the center of a segmented circle and may be lighted for night operations. The small end of the tetrahedron points in the direction of landing. Pilots are cautioned against using a tetrahedron for any purpose other than as an indicator of landing direction. Further, pilots should use extreme caution when making runway selection by use of a tetrahedron in very light or calm wind conditions as the tetrahedron may not be aligned with the designated calm−wind runway. At airports with control towers, the tetrahedron should only be referenced when the control tower is not in operation. Tower instructions supersede tetrahedron indications. 4. Landing strip indicators. Installed in pairs as shown in the segmented circle diagram and used to show the alignment of landing strips. Airport Operations AIM 5. Traffic pattern indicators. Arranged in pairs in conjunction with landing strip indicators and used to indicate the direction of turns when there is a variation from the normal left traffic pattern. (If there is no segmented circle installed at the airport, traffic pattern indicators may be installed on or near the end of the runway.) c. Preparatory to landing at an airport without a control tower, or when the control tower is not in operation, pilots should concern themselves with the indicator for the approach end of the runway to be used. When approaching for landing, all turns must be made to the left unless a traffic pattern indicator indicates that turns should be made to the right. If the pilot will mentally enlarge the indicator for the runway to be used, the base and final approach legs of the traffic pattern to be flown immediately become apparent. Similar treatment of the indicator at the departure end of the runway will clearly indicate the direction of turn after takeoff. d. When two or more aircraft are approaching an airport for the purpose of landing, the pilot of the aircraft at the lower altitude has the right−of−way over the pilot of the aircraft at the higher altitude. However, the pilot operating at the lower altitude should not take advantage of another aircraft, which is on final approach to land, by cutting in front of, or overtaking that aircraft. 4−3−5. Unexpected Maneuvers in the Airport Traffic Pattern There have been several incidents in the vicinity of controlled airports that were caused primarily by aircraft executing unexpected maneuvers. ATC service is based upon observed or known traffic and airport conditions. Controllers establish the sequence of arriving and departing aircraft by requiring them to adjust flight as necessary to achieve proper spacing. These adjustments can only be based on observed traffic, accurate pilot reports, and anticipated aircraft maneuvers. Pilots are expected to cooperate so as to preclude disrupting traffic flows or creating conflicting patterns. The pilot−in−command of an aircraft is directly responsible for and is the final authority as to the operation of the aircraft. On occasion it may be necessary for pilots to maneuver their aircraft to maintain spacing with the traffic they have been sequenced to follow. The controller can anticipate minor maneuvering such as shallow “S” turns. The controller cannot, however, anticipate a 4−3−7 AIM 6/17/21 major maneuver such as a 360 degree turn. If a pilot makes a 360 degree turn after obtaining a landing sequence, the result is usually a gap in the landing interval and, more importantly, it causes a chain reaction which may result in a conflict with following traffic and an interruption of the sequence established by the tower or approach controller. Should a pilot decide to make maneuvering turns to maintain spacing behind a preceding aircraft, the pilot should always advise the controller if at all possible. Except when requested by the controller or in emergency situations, a 360 degree turn should never be executed in the traffic pattern or when receiving radar service without first advising the controller. 4−3−6. Use of Runways/Declared Distances a. Runways are identified by numbers which indicate the nearest 10-degree increment of the azimuth of the runway centerline. For example, where the magnetic azimuth is 183 degrees, the runway designation would be 18; for a magnetic azimuth of 87 degrees, the runway designation would be 9. For a magnetic azimuth ending in the number 5, such as 185, the runway designation could be either 18 or 19. Wind direction issued by the tower is also magnetic and wind velocity is in knots. b. Airport proprietors are responsible for taking the lead in local aviation noise control. Accordingly, they may propose specific noise abatement plans to the FAA. If approved, these plans are applied in the form of Formal or Informal Runway Use Programs for noise abatement purposes. REFERENCE− Pilot/Controller Glossary Term− Runway Use Program 1. At airports where no runway use program is established, ATC clearances may specify: (a) The runway most nearly aligned with the wind when it is 5 knots or more; (b) The “calm wind” runway when wind is less than 5 knots; or geous. (c) Another runway if operationally advanta- NOTE− It is not necessary for a controller to specifically inquire if the pilot will use a specific runway or to offer a choice of runways. If a pilot prefers to use a different runway from that specified, or the one most nearly aligned with the wind, the pilot is expected to inform ATC accordingly. 4−3−8 2. At airports where a runway use program is established, ATC will assign runways deemed to have the least noise impact. If in the interest of safety a runway different from that specified is preferred, the pilot is expected to advise ATC accordingly. ATC will honor such requests and advise pilots when the requested runway is noise sensitive. When use of a runway other than the one assigned is requested, pilot cooperation is encouraged to preclude disruption of traffic flows or the creation of conflicting patterns. c. Declared Distances. 1. Declared distances for a runway represent the maximum distances available and suitable for meeting takeoff and landing distance performance requirements. These distances are determined in accordance with FAA runway design standards by adding to the physical length of paved runway any clearway or stopway and subtracting from that sum any lengths necessary to obtain the standard runway safety areas, runway object free areas, or runway protection zones. As a result of these additions and subtractions, the declared distances for a runway may be more or less than the physical length of the runway as depicted on aeronautical charts and related publications, or available in electronic navigation databases provided by either the U.S. Government or commercial companies. 2. All 14 CFR Part 139 airports report declared distances for each runway. Other airports may also report declared distances for a runway if necessary to meet runway design standards or to indicate the presence of a clearway or stopway. Where reported, declared distances for each runway end are published in the Chart Supplement U.S. For runways without published declared distances, the declared distances may be assumed to be equal to the physical length of the runway unless there is a displaced landing threshold, in which case the Landing Distance Available (LDA) is shortened by the amount of the threshold displacement. NOTE− is shown on U.S. Government charts to A symbol indicate that runway declared distance information is available (See appropriate Chart Supplement U.S., Chart Supplement Alaska or Pacific). (a) The FAA uses the following definitions for runway declared distances (See FIG 4−3−5): REFERENCE− Pilot/Controller Glossary Terms: “Accelerate−Stop Distance Available,” “Landing Distance Available,” “Takeoff Distance Available,” “Takeoff Run Available,” ” Stopway,” and “Clearway.” Airport Operations 6/17/21 (1) Takeoff Run Available (TORA) – The runway length declared available and suitable for the ground run of an airplane taking off. The TORA is typically the physical length of the runway, but it may be shorter than the runway length if necessary to satisfy runway design standards. For example, the TORA may be shorter than the runway length if a portion of the runway must be used to satisfy runway protection zone requirements. (2) Takeoff Distance Available (TODA) – The takeoff run available plus the length of any remaining runway or clearway beyond the far end of the takeoff run available. The TODA is the distance declared available for satisfying takeoff distance requirements for airplanes where the certification and operating rules and available performance data allow for the consideration of a clearway in takeoff performance computations. NOTE− The length of any available clearway will be included in the TODA published in the entry for that runway end within the Chart Supplement U.S. (3) Accelerate−Stop Distance Available (ASDA) – The runway plus stopway length declared available and suitable for the acceleration and deceleration of an airplane aborting a takeoff. The ASDA may be longer than the physical length of the runway when a stopway has been designated available by the airport operator, or it may be shorter than the physical length of the runway if necessary to use a portion of the runway to satisfy runway design standards; for example, where the airport operator uses a portion of the runway to achieve the runway safety area requirement. ASDA is the distance used to satisfy the airplane accelerate−stop distance performance requirements where the certification and operating rules require accelerate−stop distance computations. NOTE− The length of any available stopway will be included in the ASDA published in the entry for that runway end within the Chart Supplement U.S. (4) Landing Distance Available (LDA) − The runway length declared available and suitable for a landing airplane. Airport Operations AIM The LDA may be less than the physical length of the runway or the length of the runway remaining beyond a displaced threshold if necessary to satisfy runway design standards;for example, where the airport operator uses a portion of the runway to achieve the runway safety area requirement. Although some runway elements (such as stopway length and clearway length) may be available information, pilots must use the declared distances determined by the airport operator and not attempt to independently calculate declared distances by adding those elements to the reported physical length of the runway. (b) The airplane operating rules and/or the airplane operating limitations establish minimum distance requirements for takeoff and landing and are based on performance data supplied in the Airplane Flight Manual or Pilot’s Operating Handbook. The minimum distances required for takeoff and landing obtained either in planning prior to takeoff or in performance assessments conducted at the time of landing must fall within the applicable declared distances before the pilot can accept that runway for takeoff or landing. (c) Runway design standards may impose restrictions on the amount of runway available for use in takeoff and landing that are not apparent from the reported physical length of the runway or from runway markings and lighting. The runway elements of Runway Safety Area (RSA), Runway Object Free Area (ROFA), and Runway Protection Zone (RPZ) may reduce a runway’s declared distances to less than the physical length of the runway at geographically constrained airports (See FIG 4−3−6). When considering the amount of runway available for use in takeoff or landing performance calculations, the declared distances published for a runway must always be used in lieu of the runway’s physical length. REFERENCE− AC 150/5300−13, Airport Design (d) While some runway elements associated with declared distances may be identifiable through runway markings or lighting (for example, a displaced threshold or a stopway), the individual declared distance limits are not marked or otherwise identified on the runway. An aircraft is not prohibited from operating beyond a declared distance limit during the takeoff, landing, or taxi operation 4−3−9 AIM provided the runway surface is appropriately marked as usable runway (See FIG 4−3−6). The following examples clarify the intent of this paragraph. REFERENCE− AIM, Paragraph 2−3−3 , Runway Markings AC 150/5340−1, Standards for Airport Markings EXAMPLE− 1. The declared LDA for runway 9 must be used when showing compliance with the landing distance requirements of the applicable airplane operating rules and/or airplane operating limitations or when making a before landing performance assessment. The LDA is less than the physical runway length, not only because of the displaced 4−3−10 6/17/21 threshold, but also because of the subtractions necessary to meet the RSA beyond the far end of the runway. However, during the actual landing operation, it is permissible for the airplane to roll beyond the unmarked end of the LDA. 2. The declared ASDA for runway 9 must be used when showing compliance with the accelerate−stop distance requirements of the applicable airplane operating rules and/or airplane operating limitations. The ASDA is less than the physical length of the runway due to subtractions necessary to achieve the full RSA requirement. However, in the event of an aborted takeoff, it is permissible for the airplane to roll beyond the unmarked end of the ASDA as it is brought to a full−stop on the remaining usable runway. Airport Operations 6/17/21 AIM FIG 4−3−5 Declared Distances with Full−Standard Runway Safety Areas, Runway Object Free Areas, and Runway Protection Zones Airport Operations 4−3−11 AIM 6/17/21 FIG 4−3−6 Effects of a Geographical Constraint on a Runway’s Declared Distances NOTE− A runway’s RSA begins a set distance prior to the threshold and will extend a set distance beyond the end of the runway depending on the runway’s design criteria. If these required lengths cannot be achieved, the ASDA and/or LDA will be reduced as necessary to obtain the required lengths to the extent practicable. 4−3−12 Airport Operations 12/2/21 6/17/21 4−3−7. Low Level Wind Shear/Microburst Detection Systems Low Level Wind Shear Alert System (LLWAS), Terminal Doppler Weather Radar (TDWR), Weather Systems Processor (WSP), and Integrated Terminal Weather System (ITWS) display information on hazardous wind shear and microburst activity in the vicinity of an airport to air traffic controllers who relay this information to pilots. a. LLWAS provides wind shear alert and gust front information but does not provide microburst alerts. The LLWAS is designed to detect low level wind shear conditions around the periphery of an airport. It does not detect wind shear beyond that limitation. Controllers will provide this information to pilots by giving the pilot the airport wind followed by the boundary wind. EXAMPLE− Wind shear alert, airport wind 230 at 8, south boundary wind 170 at 20. b. LLWAS “network expansion,” (LLWAS NE) and LLWAS Relocation/Sustainment (LLWAS−RS) are systems integrated with TDWR. These systems provide the capability of detecting microburst alerts and wind shear alerts. Controllers will issue the appropriate wind shear alerts or microburst alerts. In some of these systems controllers also have the ability to issue wind information oriented to the threshold or departure end of the runway. EXAMPLE− Runway 17 arrival microburst alert, 40 knot loss 3 mile final. REFERENCE− AIM, Para 7−1−24, Microbursts. c. More advanced systems are in the field or being developed such as ITWS. ITWS provides alerts for microbursts, wind shear, and significant thunderstorm activity. ITWS displays wind information oriented to the threshold or departure end of the runway. d. The WSP provides weather processor enhancements to selected Airport Surveillance Radar (ASR)−9 facilities. The WSP provides Air Traffic with detection and alerting of hazardous weather such as wind shear, microbursts, and significant thunderstorm activity. The WSP displays terminal area 6 level weather, storm cell locations and movement, as well as the location and predicted future position Airport Operations AIM and intensity of wind shifts that may affect airport operations. Controllers will receive and issue alerts based on Areas Noted for Attention (ARENA). An ARENA extends on the runway center line from a 3 mile final to the runway to a 2 mile departure. e. An airport equipped with the LLWAS, ITWS, or WSP is so indicated in the Chart Supplement U.S. under Weather Data Sources for that particular airport. 4−3−8. Braking Action Reports and Advisories a. When available, ATC furnishes pilots the quality of braking action received from pilots. The quality of braking action is described by the terms “good,” “good to medium,” “medium,” “medium to poor,” “poor,” and “nil.” When pilots report the quality of braking action by using the terms noted above, they should use descriptive terms that are easily understood, such as, “braking action poor the first/last half of the runway,” together with the particular type of aircraft. b. FICON NOTAMs will provide contaminant measurements for paved runways; however, a FICON NOTAM for braking action will only be used for non−paved runway surfaces, taxiways, and aprons. These NOTAMs are classified according to the most critical term (“good to medium,” “medium,” “medium to poor,” and “poor”). 1. FICON NOTAM reporting of a braking condition for paved runway surfaces is not permissible by Federally Obligated Airports or those airports certificated under 14 CFR Part 139. 2. A “NIL” braking condition at these airports must be mitigated by closure of the affected surface. Do not include the type of vehicle in the FICON NOTAM. c. When tower controllers receive runway braking action reports which include the terms medium, poor, or nil, or whenever weather conditions are conducive to deteriorating or rapidly changing runway braking conditions, the tower will include on the ATIS broadcast the statement, “BRAKING ACTION ADVISORIES ARE IN EFFECT.” d. During the time that braking action advisories are in effect, ATC will issue the most recent braking action report for the runway in use to each arriving and departing aircraft. Pilots should be prepared for 4−3−13 AIM 6/17/21 deteriorating braking conditions and should request current runway condition information if not issued by controllers. Pilots should also be prepared to provide a descriptive runway condition report to controllers after landing. 4−3−9. Runway Condition Reports a. Aircraft braking coefficient is dependent upon the surface friction between the tires on the aircraft wheels and the pavement surface. Less friction means less aircraft braking coefficient and less aircraft braking response. b. Runway condition code (RwyCC) values range from 1 (poor) to 6 (dry). For frozen contaminants on runway surfaces, a runway condition code reading of 4 indicates the level when braking deceleration or directional control is between good and medium. NOTE− A RwyCC of “0” is used to delineate a braking action report of NIL and is prohibited from being reported in a FICON NOTAM. c. Airport management should conduct runway condition assessments on wet runways or runways covered with compacted snow and/or ice. 1. Numerical readings may be obtained by using the Runway Condition Assessment Matrix (RCAM). The RCAM provides the airport operator with data to complete the report that includes the following: (a) Runway(s) in use (b) Time of the assessment (c) Runway condition codes for each zone (touchdown, mid−point, roll−out) 4−3−14 (d) Pilot−reported braking action report (if available) (e) The contaminant (for example, wet snow, dry snow, slush, ice, etc.) 2. Assessments for each zone (see 4−3−9c1(c)) will be issued in the direction of takeoff and landing on the runway, ranging from “1” to “6” to describe contaminated surfaces. NOTE− A RwyCC of “0” is used to delineate a braking action report of NIL and is prohibited from being reported in a FICON NOTAM. 3. When any 1 or more runway condition codes are reported as less than 6, airport management must notify ATC for dissemination to pilots. 4. Controllers will not issue runway condition codes when all 3 segments of a runway are reporting values of 6. d. When runway condition code reports are provided by airport management, the ATC facility providing approach control or local airport advisory must provide the report to all pilots. e. Pilots should use runway condition code information with other knowledge including aircraft performance characteristics, type, and weight, previous experience, wind conditions, and aircraft tire type (such as bias ply vs. radial constructed) to determine runway suitability. f. The Runway Condition Assessment Matrix identifies the descriptive terms “good,” “good to medium,” “medium,” “medium to poor,” “poor,” and “nil” used in braking action reports. REFERENCE− Advisory Circular AC 91−79A (Revision 1), Mitigating the Risks of a Runway Overrun Upon Landing, Appendix 1 Airport Operations 6/17/21 AIM FIG 4−3−7 Runway Condition Assessment Matrix (RCAM) Airport Operations 4−3−15 AIM 4−3−10. Intersection Takeoffs a. In order to enhance airport capacities, reduce taxiing distances, minimize departure delays, and provide for more efficient movement of air traffic, controllers may initiate intersection takeoffs as well as approve them when the pilot requests. If for ANY reason a pilot prefers to use a different intersection or the full length of the runway or desires to obtain the distance between the intersection and the runway end, THE PILOT IS EXPECTED TO INFORM ATC ACCORDINGLY. b. Pilots are expected to assess the suitability of an intersection for use at takeoff during their preflight planning. They must consider the resultant length reduction to the published runway length and to the published declared distances from the intersection intended to be used for takeoff. The minimum runway required for takeoff must fall within the reduced runway length and the reduced declared distances before the intersection can be accepted for takeoff. REFERENCE− AIM, Paragraph 4−3−6 , Use of Runways/Declared Distances c. Controllers will issue the measured distance from the intersection to the runway end rounded “down” to the nearest 50 feet to any pilot who requests and to all military aircraft, unless use of the intersection is covered in appropriate directives. Controllers, however, will not be able to inform pilots of the distance from the intersection to the end of any of the published declared distances. REFERENCE− FAA Order JO 7110.65, Paragraph 3−7−1, Ground Traffic Movement d. An aircraft is expected to taxi to (but not onto) the end of the assigned runway unless prior approval for an intersection departure is received from ground control. e. Pilots should state their position on the airport when calling the tower for takeoff from a runway intersection. EXAMPLE− Cleveland Tower, Apache Three Seven Two Two Papa, at the intersection of taxiway Oscar and runway two three right, ready for departure. f. Controllers are required to separate small aircraft that are departing from an intersection on the same runway (same or opposite direction) behind a large nonheavy aircraft (except B757), by ensuring that at least a 3−minute interval exists between the 4−3−16 6/17/21 time the preceding large aircraft has taken off and the succeeding small aircraft begins takeoff roll. The 3−minute separation requirement will also be applied to small aircraft with a maximum certificated takeoff weight of 12,500 pounds or less departing behind a small aircraft with a maximum certificated takeoff weight of more than 12,500 pounds. To inform the pilot of the required 3−minute hold, the controller will state, “Hold for wake turbulence.” If after considering wake turbulence hazards, the pilot feels that a lesser time interval is appropriate, the pilot may request a waiver to the 3−minute interval. To initiate such a request, simply say “Request waiver to 3−minute interval” or a similar statement. Controllers may then issue a takeoff clearance if other traffic permits, since the pilot has accepted the responsibility for wake turbulence separation. g. The 3−minute interval is not required when the intersection is 500 feet or less from the departure point of the preceding aircraft and both aircraft are taking off in the same direction. Controllers may permit the small aircraft to alter course after takeoff to avoid the flight path of the preceding departure. h. A 4−minute interval is mandatory for small, large, and heavy aircraft behind a super aircraft. The 3−minute interval is mandatory behind a heavy aircraft in all cases, and for small aircraft behind a B757. 4−3−11. Pilot Responsibilities When Conducting Land and Hold Short Operations (LAHSO) a. LAHSO is an acronym for “Land and Hold Short Operations.” These operations include landing and holding short of an intersecting runway, an intersecting taxiway, or some other designated point on a runway other than an intersecting runway or taxiway. (See FIG 4−3−8, FIG 4−3−9, FIG 4−3−10.) b. Pilot Responsibilities and Basic Procedures. 1. LAHSO is an air traffic control procedure that requires pilot participation to balance the needs for increased airport capacity and system efficiency, consistent with safety. This procedure can be done safely provided pilots and controllers are knowledgeable and understand their responsibilities. The following paragraphs outline specific pilot/operator responsibilities when conducting LAHSO. 2. At controlled airports, air traffic may clear a pilot to land and hold short. Pilots may accept such a Airport Operations 6/17/21 clearance provided that the pilot−in−command determines that the aircraft can safely land and stop within the Available Landing Distance (ALD). ALD data are published in the special notices section of the Chart Supplement U.S. and in the U.S. Terminal Procedures Publications. Controllers will also provide ALD data upon request. Student pilots or pilots not familiar with LAHSO should not participate in the program. AIM FIG 4−3−8 Land and Hold Short of an Intersecting Runway 3. The pilot−in−command has the final authority to accept or decline any land and hold short clearance. The safety and operation of the aircraft remain the responsibility of the pilot. Pilots are expected to decline a LAHSO clearance if they determine it will compromise safety. 4. To conduct LAHSO, pilots should become familiar with all available information concerning LAHSO at their destination airport. Pilots should have, readily available, the published ALD and runway slope information for all LAHSO runway combinations at each airport of intended landing. Additionally, knowledge about landing performance data permits the pilot to readily determine that the ALD for the assigned runway is sufficient for safe LAHSO. As part of a pilot’s preflight planning process, pilots should determine if their destination airport has LAHSO. If so, their preflight planning process should include an assessment of which LAHSO combinations would work for them given their aircraft’s required landing distance. Good pilot decision making is knowing in advance whether one can accept a LAHSO clearance if offered. Airport Operations EXAMPLE− FIG 4−3−10 − holding short at a designated point may be required to avoid conflicts with the runway safety area/flight path of a nearby runway. NOTE− Each figure shows the approximate location of LAHSO markings, signage, and in−pavement lighting when installed. REFERENCE− AIM, Chapter 2, Aeronautical Lighting and Other Airport Visual Aids. FIG 4−3−9 Land and Hold Short of an Intersecting Taxiway 4−3−17 AIM 6/17/21 FIG 4−3−10 Land and Hold Short of a Designated Point on a Runway Other Than an Intersecting Runway or Taxiway without prompting. Don’t make the controller have to ask for a read back! c. LAHSO Situational Awareness 1. Situational awareness is vital to the success of LAHSO. Situational awareness starts with having current airport information in the cockpit, readily accessible to the pilot. (An airport diagram assists pilots in identifying their location on the airport, thus reducing requests for “progressive taxi instructions” from controllers.) 2. Situational awareness includes effective pilot−controller radio communication. ATC expects pilots to specifically acknowledge and read back all LAHSO clearances as follows: 5. If, for any reason, such as difficulty in discerning the location of a LAHSO intersection, wind conditions, aircraft condition, etc., the pilot elects to request to land on the full length of the runway, to land on another runway, or to decline LAHSO, a pilot is expected to promptly inform air traffic, ideally even before the clearance is issued. A LAHSO clearance, once accepted, must be adhered to, just as any other ATC clearance, unless an amended clearance is obtained or an emergency occurs. A LAHSO clearance does not preclude a rejected landing. 6. A pilot who accepts a LAHSO clearance should land and exit the runway at the first convenient taxiway (unless directed otherwise) before reaching the hold short point. Otherwise, the pilot must stop and hold at the hold short point. If a rejected landing becomes necessary after accepting a LAHSO clearance, the pilot should maintain safe separation from other aircraft or vehicles, and should promptly notify the controller. 7. Controllers need a full read back of all LAHSO clearances. Pilots should read back their LAHSO clearance and include the words, “HOLD SHORT OF (RUNWAY/TAXIWAY/OR POINT)” in their acknowledgment of all LAHSO clearances. In order to reduce frequency congestion, pilots are encouraged to read back the LAHSO clearance 4−3−18 EXAMPLE− ATC: “(Aircraft ID) cleared to land runway six right, hold short of taxiway bravo for crossing traffic (type aircraft).” Aircraft: “(Aircraft ID), wilco, cleared to land runway six right to hold short of taxiway bravo.” ATC: “(Aircraft ID) cross runway six right at taxiway bravo, landing aircraft will hold short.” Aircraft: “(Aircraft ID), wilco, cross runway six right at bravo, landing traffic (type aircraft) to hold.” 3. For those airplanes flown with two crewmembers, effective intra−cockpit communication between cockpit crewmembers is also critical. There have been several instances where the pilot working the radios accepted a LAHSO clearance but then simply forgot to tell the pilot flying the aircraft. 4. Situational awareness also includes a thorough understanding of the airport markings, signage, and lighting associated with LAHSO. These visual aids consist of a three−part system of yellow hold−short markings, red and white signage and, in certain cases, in−pavement lighting. Visual aids assist the pilot in determining where to hold short. FIG 4−3−8, FIG 4−3−9, FIG 4−3−10 depict how these markings, signage, and lighting combinations will appear once installed. Pilots are cautioned that not all airports conducting LAHSO have installed any or all of the above markings, signage, or lighting. 5. Pilots should only receive a LAHSO clearance when there is a minimum ceiling of 1,000 feet and 3 statute miles visibility. The intent of having “basic” VFR weather conditions is to allow pilots to maintain visual contact with other aircraft and ground vehicle operations. Pilots should consider the effects of prevailing inflight visibility (such as landing into the sun) and how it may affect overall Airport Operations 6/17/21 situational awareness. Additionally, surface vehicles and aircraft being taxied by maintenance personnel may also be participating in LAHSO, especially in those operations that involve crossing an active runway. 4−3−12. Low Approach a. A low approach (sometimes referred to as a low pass) is the go−around maneuver following an approach. Instead of landing or making a touch−and− go, a pilot may wish to go around (low approach) in order to expedite a particular operation (a series of practice instrument approaches is an example of such an operation). Unless otherwise authorized by ATC, the low approach should be made straight ahead, with no turns or climb made until the pilot has made a thorough visual check for other aircraft in the area. b. When operating within a Class B, Class C, and Class D surface area, a pilot intending to make a low approach should contact the tower for approval. This request should be made prior to starting the final approach. c. When operating to an airport, not within a Class B, Class C, and Class D surface area, a pilot intending to make a low approach should, prior to leaving the final approach fix inbound (nonprecision approach) or the outer marker or fix used in lieu of the outer marker inbound (precision approach), so advise the FSS, UNICOM, or make a broadcast as appropriate. REFERENCE− AIM, Paragraph 4−1−9 , Traffic Advisory Practices at Airports Without Operating Control Towers 4−3−13. Traffic Control Light Signals a. The following procedures are used by ATCTs in the control of aircraft, ground vehicles, equipment, Airport Operations AIM and personnel not equipped with radio. These same procedures will be used to control aircraft, ground vehicles, equipment, and personnel equipped with radio if radio contact cannot be established. ATC personnel use a directive traffic control signal which emits an intense narrow light beam of a selected color (either red, white, or green) when controlling traffic by light signals. b. Although the traffic signal light offers the advantage that some control may be exercised over nonradio equipped aircraft, pilots should be cognizant of the disadvantages which are: 1. Pilots may not be looking at the control tower at the time a signal is directed toward their aircraft. 2. The directions transmitted by a light signal are very limited since only approval or disapproval of a pilot’s anticipated actions may be transmitted. No supplement or explanatory information may be transmitted except by the use of the “General Warning Signal” which advises the pilot to be on the alert. c. Between sunset and sunrise, a pilot wishing to attract the attention of the control tower should turn on a landing light and taxi the aircraft into a position, clear of the active runway, so that light is visible to the tower. The landing light should remain on until appropriate signals are received from the tower. d. Airport Traffic Control Tower Light Gun Signals. (See TBL 4−3−1.) e. During daylight hours, acknowledge tower transmissions or light signals by moving the ailerons or rudder. At night, acknowledge by blinking the landing or navigation lights. If radio malfunction occurs after departing the parking area, watch the tower for light signals or monitor tower frequency. 4−3−19 AIM 6/17/21 TBL 4−3−1 Airport Traffic Control Tower Light Gun Signals Meaning Color and Type of Signal Movement of Vehicles, Equipment and Personnel Aircraft on the Ground Aircraft in Flight Steady green Flashing green Cleared to cross, proceed or go Not applicable Cleared for takeoff Cleared for taxi Cleared to land Return for landing (to be followed by steady green at the proper time) Steady red STOP STOP Give way to other aircraft and continue circling Flashing red Flashing white Alternating red and green Clear the taxiway/runway Taxi clear of the runway in use Airport unsafe, do not land Return to starting point on airport Return to starting point on airport Not applicable Exercise extreme caution Exercise extreme caution Exercise extreme caution 4−3−14. Communications a. Pilots of departing aircraft should communicate with the control tower on the appropriate ground control/clearance delivery frequency prior to starting engines to receive engine start time, taxi and/or clearance information. Unless otherwise advised by the tower, remain on that frequency during taxiing and runup, then change to local control frequency when ready to request takeoff clearance. NOTE− Pilots are encouraged to monitor the local tower frequency as soon as practical consistent with other ATC requirements. REFERENCE− AIM, Paragraph 4−1−13 , Automatic Terminal Information Service (ATIS) b. The tower controller will consider that pilots of turbine−powered aircraft are ready for takeoff when they reach the runway or warm−up block unless advised otherwise. c. The majority of ground control frequencies are in the 121.6−121.9 MHz bandwidth. Ground control frequencies are provided to eliminate frequency congestion on the tower (local control) frequency and are limited to communications between the tower and aircraft on the ground and between the tower and utility vehicles on the airport, provide a clear VHF channel for arriving and departing aircraft. They are used for issuance of taxi information, clearances, and other necessary contacts between the tower and aircraft or other vehicles operated on the airport. A pilot who has just landed should not change from the 4−3−20 tower frequency to the ground control frequency until directed to do so by the controller. Normally, only one ground control frequency is assigned at an airport; however, at locations where the amount of traffic so warrants, a second ground control frequency and/or another frequency designated as a clearance delivery frequency, may be assigned. d. A controller may omit the ground or local control frequency if the controller believes the pilot knows which frequency is in use. If the ground control frequency is in the 121 MHz bandwidth the controller may omit the numbers preceding the decimal point; e.g., 121.7, “CONTACT GROUND POINT SEVEN.” However, if any doubt exists as to what frequency is in use, the pilot should promptly request the controller to provide that information. e. Controllers will normally avoid issuing a radio frequency change to helicopters, known to be single−piloted, which are hovering, air taxiing, or flying near the ground. At times, it may be necessary for pilots to alert ATC regarding single pilot operations to minimize delay of essential ATC communications. Whenever possible, ATC instructions will be relayed through the frequency being monitored until a frequency change can be accomplished. You must promptly advise ATC if you are unable to comply with a frequency change. Also, you should advise ATC if you must land to accomplish the frequency change unless it is clear the landing will have no impact on other air traffic; e.g., on a taxiway or in a helicopter operating area. Airport Operations 6/17/21 4−3−15. Gate Holding Due to Departure Delays a. Pilots should contact ground control or clearance delivery prior to starting engines as gate hold procedures will be in effect whenever departure delays exceed or are anticipated to exceed 15 minutes. The sequence for departure will be maintained in accordance with initial call up unless modified by flow control restrictions. Pilots should monitor the ground control or clearance delivery frequency for engine startup advisories or new proposed start time if the delay changes. b. The tower controller will consider that pilots of turbine−powered aircraft are ready for takeoff when they reach the runway or warm−up block unless advised otherwise. 4−3−16. VFR Flights in Terminal Areas Use reasonable restraint in exercising the prerogative of VFR flight, especially in terminal areas. The weather minimums and distances from clouds are minimums. Giving yourself a greater margin in specific instances is just good judgment. a. Approach Area. Conducting a VFR operation in a Class B, Class C, Class D, and Class E surface area when the official visibility is 3 or 4 miles is not prohibited, but good judgment would dictate that you keep out of the approach area. b. Reduced Visibility. It has always been recognized that precipitation reduces forward visibility. Consequently, although again it may be perfectly legal to cancel your IFR flight plan at any time you can proceed VFR, it is good practice, when precipitation is occurring, to continue IFR operation into a terminal area until you are reasonably close to your destination. c. Simulated Instrument Flights. In conducting simulated instrument flights, be sure that the weather is good enough to compensate for the restricted visibility of the safety pilot and your greater concentration on your flight instruments. Give yourself a little greater margin when your flight plan lies in or near a busy airway or close to an airport. 4−3−17. VFR Helicopter Operations at Controlled Airports a. General. Airport Operations AIM 1. The following ATC procedures and phraseologies recognize the unique capabilities of helicopters and were developed to improve service to all users. Helicopter design characteristics and user needs often require operations from movement areas and nonmovement areas within the airport boundary. In order for ATC to properly apply these procedures, it is essential that pilots familiarize themselves with the local operations and make it known to controllers when additional instructions are necessary. 2. Insofar as possible, helicopter operations will be instructed to avoid the flow of fixed−wing aircraft to minimize overall delays; however, there will be many situations where faster/larger helicopters may be integrated with fixed−wing aircraft for the benefit of all concerned. Examples would include IFR flights, avoidance of noise sensitive areas, or use of runways/taxiways to minimize the hazardous effects of rotor downwash in congested areas. 3. Because helicopter pilots are intimately familiar with the effects of rotor downwash, they are best qualified to determine if a given operation can be conducted safely. Accordingly, the pilot has the final authority with respect to the specific airspeed/altitude combinations. ATC clearances are in no way intended to place the helicopter in a hazardous position. It is expected that pilots will advise ATC if a specific clearance will cause undue hazards to persons or property. b. Controllers normally limit ATC ground service and instruction to movement areas; therefore, operations from nonmovement areas are conducted at pilot discretion and should be based on local policies, procedures, or letters of agreement. In order to maximize the flexibility of helicopter operations, it is necessary to rely heavily on sound pilot judgment. For example, hazards such as debris, obstructions, vehicles, or personnel must be recognized by the pilot, and action should be taken as necessary to avoid such hazards. Taxi, hover taxi, and air taxi operations are considered to be ground movements. Helicopters conducting such operations are expected to adhere to the same conditions, requirements, and practices as apply to other ground taxiing and ATC procedures in the AIM. 1. The phraseology taxi is used when it is intended or expected that the helicopter will taxi on the airport surface, either via taxiways or other prescribed routes. Taxi is used primarily for helicopters equipped with wheels or in response to a 4−3−21 AIM pilot request. Preference should be given to this procedure whenever it is necessary to minimize effects of rotor downwash. 2. Pilots may request a hover taxi when slow forward movement is desired or when it may be appropriate to move very short distances. Pilots should avoid this procedure if rotor downwash is likely to cause damage to parked aircraft or if blowing dust/snow could obscure visibility. If it is necessary to operate above 25 feet AGL when hover taxiing, the pilot should initiate a request to ATC. 3. Air taxi is the preferred method for helicopter ground movements on airports provided ground operations and conditions permit. Unless otherwise requested or instructed, pilots are expected to remain below 100 feet AGL. However, if a higher than normal airspeed or altitude is desired, the request should be made prior to lift−off. The pilot is solely responsible for selecting a safe airspeed for the altitude/operation being conducted. Use of air taxi enables the pilot to proceed at an optimum airspeed/altitude, minimize downwash effect, conserve fuel, and expedite movement from one point to another. Helicopters should avoid overflight of other aircraft, vehicles, and personnel during air−taxi operations. Caution must be exercised concerning active runways and pilots must be certain that air taxi instructions are understood. Special precautions may be necessary at unfamiliar airports or airports with multiple/intersecting active runways. The taxi procedures given in Paragraph 4−3−18, Taxiing, Paragraph 4−3−19, Taxi During Low Visibility, and Paragraph 4−3−20, Exiting the Runway After Landing, also apply. REFERENCE− Pilot/Controller Glossary Term− Taxi. Pilot/Controller Glossary Term− Hover Taxi. Pilot/Controller Glossary Term− Air Taxi. c. Takeoff and Landing Procedures. 1. Helicopter operations may be conducted from a runway, taxiway, portion of a landing strip, or any clear area which could be used as a landing site such as the scene of an accident, a construction site, or the roof of a building. The terms used to describe designated areas from which helicopters operate are: movement area, landing/takeoff area, apron/ramp, heliport and helipad (See Pilot/Controller Glossary). 4−3−22 6/17/21 These areas may be improved or unimproved and may be separate from or located on an airport/heliport. ATC will issue takeoff clearances from movement areas other than active runways, or in diverse directions from active runways, with additional instructions as necessary. Whenever possible, takeoff clearance will be issued in lieu of extended hover/air taxi operations. Phraseology will be “CLEARED FOR TAKEOFF FROM (taxiway, helipad, runway number, etc.), MAKE RIGHT/ LEFT TURN FOR (direction, heading, NAVAID radial) DEPARTURE/DEPARTURE ROUTE (number, name, etc.).” Unless requested by the pilot, downwind takeoffs will not be issued if the tailwind exceeds 5 knots. 2. Pilots should be alert to wind information as well as to wind indications in the vicinity of the helicopter. ATC should be advised of the intended method of departing. A pilot request to takeoff in a given direction indicates that the pilot is willing to accept the wind condition and controllers will honor the request if traffic permits. Departure points could be a significant distance from the control tower and it may be difficult or impossible for the controller to determine the helicopter’s relative position to the wind. 3. If takeoff is requested from nonmovement areas, an area not authorized for helicopter use, an area not visible from the tower, an unlighted area at night, or an area off the airport, the phraseology “DEPARTURE FROM (requested location) WILL BE AT YOUR OWN RISK (additional instructions, as necessary). USE CAUTION (if applicable).” The pilot is responsible for operating in a safe manner and should exercise due caution. 4. Similar phraseology is used for helicopter landing operations. Every effort will be made to permit helicopters to proceed direct and land as near as possible to their final destination on the airport. Traffic density, the need for detailed taxiing instructions, frequency congestion, or other factors may affect the extent to which service can be expedited. As with ground movement operations, a high degree of pilot/controller cooperation and communication is necessary to achieve safe and efficient operations. Airport Operations 12/2/21 6/17/21 4−3−18. Taxiing a. General. Approval must be obtained prior to moving an aircraft or vehicle onto the movement area during the hours an Airport Traffic Control Tower is in operation. 1. Always state your position on the airport when calling the tower for taxi instructions. 2. The movement area is normally described in local bulletins issued by the airport manager or control tower. These bulletins may be found in FSSs, fixed base operators offices, air carrier offices, and operations offices. 3. The control tower also issues bulletins describing areas where they cannot provide ATC service due to nonvisibility or other reasons. 4. A clearance must be obtained prior to taxiing on a runway, taking off, or landing during the hours an Airport Traffic Control Tower is in operation. 5. A clearance must be obtained prior to crossing any runway. ATC will issue an explicit clearance for all runway crossings. 6. When assigned a takeoff runway, ATC will first specify the runway, issue taxi instructions, and state any hold short instructions or runway crossing clearances if the taxi route will cross a runway. This does not authorize the aircraft to “enter” or “cross” the assigned departure runway at any point. In order to preclude misunderstandings in radio communications, ATC will not use the word “cleared” in conjunction with authorization for aircraft to taxi. 7. When issuing taxi instructions to any point other than an assigned takeoff runway, ATC will specify the point to taxi to, issue taxi instructions, and state any hold short instructions or runway crossing clearances if the taxi route will cross a runway. NOTE− ATC is required to obtain a readback from the pilot of all runway hold short instructions. 8. If a pilot is expected to hold short of a runway approach/departure (Runway XX APPCH/ Runway XX DEP) hold area or ILS holding position (see FIG 2−3−15, Taxiways Located in Runway Approach Area), ATC will issue instructions. 9. When taxi instructions are received from the controller, pilots should always read back: (a) The runway assignment. Airport Operations AIM (b) Any clearance to enter a specific runway. (c) Any instruction to hold short of a specific runway or line up and wait. 10. Controllers are required to request a readback of runway hold short assignment when it is not received from the pilot/vehicle. b. ATC clearances or instructions pertaining to taxiing are predicated on known traffic and known physical airport conditions. Therefore, it is important that pilots clearly understand the clearance or instruction. Although an ATC clearance is issued for taxiing purposes, when operating in accordance with the CFRs, it is the responsibility of the pilot to avoid collision with other aircraft. Since “the pilot−in−command of an aircraft is directly responsible for, and is the final authority as to, the operation of that aircraft” the pilot should obtain clarification of any clearance or instruction which is not understood. 1. Good operating practice dictates that pilots acknowledge all runway crossing, hold short, or takeoff clearances unless there is some misunderstanding, at which time the pilot should query the controller until the clearance is understood. NOTE− Air traffic controllers are required to obtain from the pilot a readback of all runway hold short instructions. 2. Pilots operating a single pilot aircraft should monitor only assigned ATC communications after being cleared onto the active runway for departure. Single pilot aircraft should not monitor other than ATC communications until flight from Class B, Class C, or Class D surface area is completed. This same procedure should be practiced from after receipt of the clearance for landing until the landing and taxi activities are complete. Proper effective scanning for other aircraft, surface vehicles, or other objects should be continuously exercised in all cases. 3. If the pilot is unfamiliar with the airport or for any reason confusion exists as to the correct taxi routing, a request may be made for progressive taxi instructions which include step−by−step routing directions. Progressive instructions may also be issued if the controller deems it necessary due to traffic or field conditions (for example, construction or closed taxiways). c. At those airports where the U.S. Government operates the control tower and ATC has authorized noncompliance with the requirement for two−way 4−3−23 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 radio communications while operating within the Class B, Class C, or Class D surface area, or at those airports where the U.S. Government does not operate the control tower and radio communications cannot be established, pilots must obtain a clearance by visual light signal prior to taxiing on a runway and prior to takeoff and landing. request clearance to Page.” d. The following phraseologies and procedures are used in radiotelephone communications with aeronautical ground stations. Aircraft: “Orlando ground, Beechcraft One Four Two Six One clearing runway one eight left at taxiway bravo three, request clearance to Page.” 1. Request for taxi instructions prior to departure. State your aircraft identification, location, type of operation planned (VFR or IFR), and the point of first intended landing. Tower: “Beechcraft One Four Two Six One, Orlando ground, hold short of runway one eight right.” EXAMPLE− Aircraft: “Washington ground, Beechcraft One Three One Five Niner at hangar eight, ready to taxi, I−F−R to Chicago.” e. During ground operations, jet blast, prop wash, and rotor wash can cause damage and upsets if encountered at close range. Pilots should consider the effects of jet blast, prop wash, and rotor wash on aircraft, vehicles, and maintenance equipment during ground operations. Tower: “Beechcraft one three one five niner, Washington ground, runway two seven, taxi via taxiways Charlie and Delta, hold short of runway three three left.” Aircraft: “Beechcraft One Three One Five Niner, runway two seven, hold short of runway three three left.” 2. Receipt of ATC clearance. ARTCC clearances are relayed to pilots by airport traffic controllers in the following manner. EXAMPLE− Tower: “Beechcraft One Three One Five Niner, cleared to the Chicago Midway Airport via Victor Eight, maintain eight thousand.” Aircraft: “Beechcraft One Three One Five Niner, cleared to the Chicago Midway Airport via Victor Eight, maintain eight thousand.” NOTE− Normally, an ATC IFR clearance is relayed to a pilot by the ground controller. At busy locations, however, pilots may be instructed by the ground controller to “contact clearance delivery” on a frequency designated for this purpose. No surveillance or control over the movement of traffic is exercised by this position of operation. 3. Request for taxi instructions after landing. State your aircraft identification, location, and that you request taxi instructions. EXAMPLE− Aircraft: “Dulles ground, Beechcraft One Four Two Six One clearing runway one right on taxiway echo three, 4−3−24 Tower: “Beechcraft One Four Two Six One, Dulles ground, taxi to Page via taxiways echo three, echo one, and echo niner.” or Aircraft: “Beechcraft One Four Two Six One, hold short of runway one eight right.” 4−3−19. Taxi During Low Visibility a. Pilots and aircraft operators should be constantly aware that during certain low visibility conditions the movement of aircraft and vehicles on airports may not be visible to the tower controller. This may prevent visual confirmation of an aircraft’s adherence to taxi instructions. b. Of vital importance is the need for pilots to notify the controller when difficulties are encountered or at the first indication of becoming disoriented. Pilots should proceed with extreme caution when taxiing toward the sun. When vision difficulties are encountered pilots should immediately inform the controller. c. Advisory Circular 120−57, Low Visibility Operations Surface Movement Guidance and Control System, commonly known as LVOSMGCS (pronounced “LVO SMIGS”) describes an adequate example of a low visibility taxi plan for any airport which has takeoff or landing operations in less than 1,200 feet runway visual range (RVR) visibility conditions. These plans, which affect aircrew and vehicle operators, may incorporate additional lighting, markings, and procedures to control airport surface traffic. They will be addressed at two levels; operations less than 1,200 feet RVR to 500 feet RVR and operations less than 500 feet RVR. Airport Operations 12/2/21 6/17/21 AIM NOTE− Specific lighting systems and surface markings may be found in paragraph 2−1−10, Taxiway Lights, and paragraph 2−3−4, Taxiway Markings. 2. Ground control will issue taxi clearance to parking. That clearance does not authorize the aircraft to “enter” or “cross” any runways. Pilots not familiar with the taxi route should request specific taxi instructions from ATC. d. When low visibility conditions exist, pilots should focus their entire attention on the safe operation of the aircraft while it is moving. Checklists and nonessential communication should be withheld until the aircraft is stopped and the brakes set. 4−3−21. Practice Instrument Approaches 4−3−20. Exiting the Runway After Landing The following procedures must be followed after landing and reaching taxi speed. a. Exit the runway without delay at the first available taxiway or on a taxiway as instructed by ATC. Pilots must not exit the landing runway onto another runway unless authorized by ATC. At airports with an operating control tower, pilots should not stop or reverse course on the runway without first obtaining ATC approval. b. Taxi clear of the runway unless otherwise directed by ATC. An aircraft is considered clear of the runway when all parts of the aircraft are past the runway edge and there are no restrictions to its continued movement beyond the runway holding position markings. In the absence of ATC instructions, the pilot is expected to taxi clear of the landing runway by taxiing beyond the runway holding position markings associated with the landing runway, even if that requires the aircraft to protrude into or cross another taxiway or ramp area. Once all parts of the aircraft have crossed the runway holding position markings, the pilot must hold unless further instructions have been issued by ATC. NOTE− 1. The tower will issue the pilot instructions which will permit the aircraft to enter another taxiway, runway, or ramp area when required. 2. Guidance contained in subparagraphs a and b above is considered an integral part of the landing clearance and satisfies the requirement of 14 CFR Section 91.129. c. Immediately change to ground control frequency when advised by the tower and obtain a taxi clearance. NOTE− 1. The tower will issue instructions required to resolve any potential conflictions with other ground traffic prior to advising the pilot to contact ground control. Airport Operations a. Various air traffic incidents have indicated the necessity for adoption of measures to achieve more organized and controlled operations where practice instrument approaches are conducted. Practice instrument approaches are considered to be instrument approaches made by either a VFR aircraft not on an IFR flight plan or an aircraft on an IFR flight plan. To achieve this and thereby enhance air safety, it is Air Traffic’s policy to provide for separation of such operations at locations where approach control facilities are located and, as resources permit, at certain other locations served by ARTCCs or parent approach control facilities. Pilot requests to practice instrument approaches may be approved by ATC subject to traffic and workload conditions. Pilots should anticipate that in some instances the controller may find it necessary to deny approval or withdraw previous approval when traffic conditions warrant. It must be clearly understood, however, that even though the controller may be providing separation, pilots on VFR flight plans are required to comply with basic VFR weather minimums (14 CFR Section 91.155). Application of ATC procedures or any action taken by the controller to avoid traffic conflictions does not relieve IFR and VFR pilots of their responsibility to see−and−avoid other traffic while operating in VFR conditions (14 CFR Section 91.113). In addition to the normal IFR separation minimums (which includes visual separation) during VFR conditions, 500 feet vertical separation may be applied between VFR aircraft and between a VFR aircraft and the IFR aircraft. Pilots not on IFR flight plans desiring practice instrument approaches should always state ‘practice’ when making requests to ATC. Controllers will instruct VFR aircraft requesting an instrument approach to maintain VFR. This is to preclude misunderstandings between the pilot and controller as to the status of the aircraft. If pilots wish to proceed in accordance with instrument flight rules, they must specifically request and obtain, an IFR clearance. b. Before practicing an instrument approach, pilots should inform the approach control facility or the tower of the type of practice approach they desire to make and how they intend to terminate it, 4−3−25 7110.65R CHG 2 AIM AIM i.e., full−stop landing, touch−and−go, or missed or low approach maneuver. This information may be furnished progressively when conducting a series of approaches. Pilots on an IFR flight plan, who have made a series of instrument approaches to full stop landings should inform ATC when they make their final landing. The controller will control flights practicing instrument approaches so as to ensure that they do not disrupt the flow of arriving and departing itinerant IFR or VFR aircraft. The priority afforded itinerant aircraft over practice instrument approaches is not intended to be so rigidly applied that it causes grossly inefficient application of services. A minimum delay to itinerant traffic may be appropriate to allow an aircraft practicing an approach to complete that approach. NOTE− A clearance to land means that appropriate separation on the landing runway will be ensured. A landing clearance does not relieve the pilot from compliance with any previously issued restriction. c. At airports without a tower, pilots wishing to make practice instrument approaches should notify the facility having control jurisdiction of the desired approach as indicated on the approach chart. All approach control facilities and ARTCCs are required to publish a Letter to Airmen depicting those airports where they provide standard separation to both VFR and IFR aircraft conducting practice instrument approaches. d. The controller will provide approved separation between both VFR and IFR aircraft when authorization is granted to make practice approaches to airports where an approach control facility is located and to certain other airports served by approach control or an ARTCC. Controller responsibility for separation of VFR aircraft begins at the point where the approach clearance becomes effective, or when the aircraft enters Class B or Class C airspace, or a TRSA, whichever comes first. e. VFR aircraft practicing instrument approaches are not automatically authorized to execute the missed approach procedure. This authorization must be specifically requested by the pilot and approved by the controller. Where ATC procedures require application of IFR separation to VFR aircraft practicing instrument approaches, separation will be provided throughout the procedure including the missed approach. Where no separation services are 4−3−26 3/15/07 12/2/21 6/17/21 provided during the practice approach, no separation services will be provided during the missed approach. f. Except in an emergency, aircraft cleared to practice instrument approaches must not deviate from the approved procedure until cleared to do so by the controller. g. At radar approach control locations when a full approach procedure (procedure turn, etc.,) cannot be approved, pilots should expect to be vectored to a final approach course for a practice instrument approach which is compatible with the general direction of traffic at that airport. h. When granting approval for a practice instrument approach, the controller will usually ask the pilot to report to the tower prior to or over the final approach fix inbound (nonprecision approaches) or over the outer marker or fix used in lieu of the outer marker inbound (precision approaches). i. When authorization is granted to conduct practice instrument approaches to an airport with a tower, but where approved standard separation is not provided to aircraft conducting practice instrument approaches, the tower will approve the practice approach, instruct the aircraft to maintain VFR and issue traffic information, as required. j. When an aircraft notifies a FSS providing Local Airport Advisory to the airport concerned of the intent to conduct a practice instrument approach and whether or not separation is to be provided, the pilot will be instructed to contact the appropriate facility on a specified frequency prior to initiating the approach. At airports where separation is not provided, the FSS will acknowledge the message and issue known traffic information but will neither approve or disapprove the approach. k. Pilots conducting practice instrument approaches should be particularly alert for other aircraft operating in the local traffic pattern or in proximity to the airport. 4−3−22. Option Approach The “Cleared for the Option” procedure will permit an instructor, flight examiner or pilot the option to make a touch−and−go, low approach, missed approach, stop−and−go, or full stop landing. This procedure can be very beneficial in a training situation in that neither the student pilot nor examinee would know what maneuver would be accomplished. Airport Operations 12/2/21 6/17/21 The pilot should make a request for this procedure passing the final approach fix inbound on an instrument approach or entering downwind for a VFR traffic pattern. After ATC approval of the option, the pilot should inform ATC as soon as possible of any delay on the runway during their stop-and-go or full stop landing. The advantages of this procedure as a training aid are that it enables an instructor or examiner to obtain the reaction of a trainee or examinee under changing conditions, the pilot would not have to discontinue an approach in the middle of the procedure due to student error or pilot proficiency requirements, and finally it allows more flexibility and economy in training programs. This procedure will only be used at those locations with an operational control tower and will be subject to ATC approval. 4−3−23. Use of Aircraft Lights a. Aircraft position lights are required to be lighted on aircraft operated on the surface and in flight from sunset to sunrise. In addition, aircraft equipped with an anti−collision light system are required to operate that light system during all types of operations (day and night). However, during any adverse meteorological conditions, the pilot−in−command may determine that the anti−collision lights should be turned off when their light output would constitute a hazard to safety (14 CFR Section 91.209). Supplementary strobe lights should be turned off on the ground when they adversely affect ground personnel or other pilots, and in flight when there are adverse reflection from clouds. b. An aircraft anti−collision light system can use one or more rotating beacons and/or strobe lights, be colored either red or white, and have different (higher than minimum) intensities when compared to other aircraft. Many aircraft have both a rotating beacon and a strobe light system. c. The FAA has a voluntary pilot safety program, Operation Lights On, to enhance the see−and−avoid concept. Pilots are encouraged to turn on their landing lights during takeoff; i.e., either after takeoff clearance has been received or when beginning takeoff roll. Pilots are further encouraged to turn on their landing lights when operating below 10,000 feet, day or night, especially when operating within 10 miles of any airport, or in conditions of Airport Operations AIM reduced visibility and in areas where flocks of birds may be expected, i.e., coastal areas, lake areas, around refuse dumps, etc. Although turning on aircraft lights does enhance the see−and−avoid concept, pilots should not become complacent about keeping a sharp lookout for other aircraft. Not all aircraft are equipped with lights and some pilots may not have their lights turned on. Aircraft manufacturer’s recommendations for operation of landing lights and electrical systems should be observed. d. Prop and jet blast forces generated by large aircraft have overturned or damaged several smaller aircraft taxiing behind them. To avoid similar results, and in the interest of preventing upsets and injuries to ground personnel from such forces, the FAA recommends that air carriers and commercial operators turn on their rotating beacons anytime their aircraft engines are in operation. General aviation pilots using rotating beacon equipped aircraft are also encouraged to participate in this program which is designed to alert others to the potential hazard. Since this is a voluntary program, exercise caution and do not rely solely on the rotating beacon as an indication that aircraft engines are in operation. e. Prior to commencing taxi, it is recommended to turn on navigation, position, anti-collision, and logo lights (if equipped). To signal intent to other pilots, consider turning on the taxi light when the aircraft is moving or intending to move on the ground, and turning it off when stopped or yielding to other ground traffic. Strobe lights should not be illuminated during taxi if they will adversely affect the vision of other pilots or ground personnel. f. At the discretion of the pilot-in-command, all exterior lights should be illuminated when taxiing on or across any runway. This increases the conspicuousness of the aircraft to controllers and other pilots approaching to land, taxiing, or crossing the runway. Pilots should comply with any equipment operating limitations and consider the effects of landing and strobe lights on other aircraft in their vicinity. g. When entering the departure runway for takeoff or to “line up and wait,” all lights, except for landing lights, should be illuminated to make the aircraft conspicuous to ATC and other aircraft on approach. Landing lights should be turned on when takeoff clearance is received or when commencing takeoff roll at an airport without an operating control tower. 4−3−27 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 4−3−24. Flight Inspection/‘Flight Check’ Aircraft in Terminal Areas FIG 4−3−12 Signalman’s Position a. Flight check is a call sign used to alert pilots and air traffic controllers when a FAA aircraft is engaged in flight inspection/certification of NAVAIDs and flight procedures. Flight check aircraft fly preplanned high/low altitude flight patterns such as grids, orbits, DME arcs, and tracks, including low passes along the full length of the runway to verify NAVAID performance. b. Pilots should be especially watchful and avoid the flight paths of any aircraft using the call sign “Flight Check.” These flights will normally receive special handling from ATC. Pilot patience and cooperation in allowing uninterrupted recordings can significantly help expedite flight inspections, minimize costly, repetitive runs, and reduce the burden on the U.S. taxpayer. SIGNALMAN 4−3−25. Hand Signals FIG 4−3−13 FIG 4−3−11 Signalman Directs Towing All Clear (O.K.) SIGNALMAN 4−3−28 Airport Operations 12/2/21 6/17/21 AIM FIG 4−3−14 FIG 4−3−16 Start Engine Proceed Straight Ahead POINT TO ENGINE TO BE STARTED Airport Operations FIG 4−3−15 FIG 4−3−17 Pull Chocks Left Turn 4−3−29 7110.65R CHG 2 AIM AIM 4−3−30 3/15/07 12/2/21 6/17/21 FIG 4−3−18 FIG 4−3−20 Right Turn Flagman Directs Pilot FIG 4−3−19 FIG 4−3−21 Slow Down Insert Chocks Airport Operations 12/2/21 6/17/21 AIM FIG 4−3−22 FIG 4−3−24 Cut Engines Stop 4−3−26. Operations at Uncontrolled Airports With Automated Surface Observing System (ASOS)/Automated Weather Observing System (AWOS) FIG 4−3−23 Night Operation a. Many airports throughout the National Airspace System are equipped with either ASOS or AWOS. At most airports with an operating control tower or human observer, the weather will be available to you in an Aviation Routine Weather Report (METAR) hourly or special observation format on the Automatic Terminal Information Service (ATIS) or directly transmitted from the controller/observer. b. At uncontrolled airports that are equipped with ASOS/AWOS with ground−to−air broadcast capability, the one−minute updated airport weather should be available to you within approximately 25 NM of the airport below 10,000 feet. The frequency for the weather broadcast will be published on sectional charts and in the Chart Supplement U.S. Some part−time towered airports may also broadcast the automated weather on their ATIS frequency during the hours that the tower is closed. Use same hand movements as day operation Airport Operations c. Controllers issue SVFR or IFR clearances based on pilot request, known traffic and reported weather, i.e., METAR/Nonroutine (Special) Aviation Weather Report (SPECI) observations, when they are available. Pilots have access to more current weather 4−3−31 7110.65R CHG 2 AIM AIM at uncontrolled ASOS/AWOS airports than do the controllers who may be located several miles away. Controllers will rely on the pilot to determine the current airport weather from the ASOS/AWOS. All aircraft arriving or departing an ASOS/AWOS equipped uncontrolled airport should monitor the airport weather frequency to ascertain the status of the airspace. Pilots in Class E airspace must be alert for changing weather conditions which may affect the status of the airspace from IFR/VFR. If ATC service 4−3−32 3/15/07 12/2/21 6/17/21 is required for IFR/SVFR approach/departure or requested for VFR service, the pilot should advise the controller that he/she has received the one−minute weather and state his/her intentions. EXAMPLE− “I have the (airport) one−minute weather, request an ILS Runway 14 approach.” REFERENCE− AIM, Para 7−1−10, Weather Observing Programs. Airport Operations 6/17/21 AIM Section 4. ATC Clearances and Aircraft Separation 4−4−1. Clearance a. A clearance issued by ATC is predicated on known traffic and known physical airport conditions. An ATC clearance means an authorization by ATC, for the purpose of preventing collision between known aircraft, for an aircraft to proceed under specified conditions within controlled airspace. IT IS NOT AUTHORIZATION FOR A PILOT TO DEVIATE FROM ANY RULE, REGULATION, OR MINIMUM ALTITUDE NOR TO CONDUCT UNSAFE OPERATION OF THE AIRCRAFT. b. 14 CFR Section 91.3(a) states: “The pilot−in− command of an aircraft is directly responsible for, and is the final authority as to, the operation of that aircraft.” If ATC issues a clearance that would cause a pilot to deviate from a rule or regulation, or in the pilot’s opinion, would place the aircraft in jeopardy, IT IS THE PILOT’S RESPONSIBILITY TO REQUEST AN AMENDED CLEARANCE. Similarly, if a pilot prefers to follow a different course of action, such as make a 360 degree turn for spacing to follow traffic when established in a landing or approach sequence, land on a different runway, takeoff from a different intersection, takeoff from the threshold instead of an intersection, or delay operation, THE PILOT IS EXPECTED TO INFORM ATC ACCORDINGLY. When the pilot requests a different course of action, however, the pilot is expected to cooperate so as to preclude disruption of traffic flow or creation of conflicting patterns. The pilot is also expected to use the appropriate aircraft call sign to acknowledge all ATC clearances, frequency changes, or advisory information. c. Each pilot who deviates from an ATC clearance in response to a Traffic Alert and Collision Avoidance System resolution advisory must notify ATC of that deviation as soon as possible. REFERENCE− Pilot/Controller Glossary Term− Traffic Alert and Collision Avoidance System. d. When weather conditions permit, during the time an IFR flight is operating, it is the direct responsibility of the pilot to avoid other aircraft since VFR flights may be operating in the same area without the knowledge of ATC. Traffic clearances ATC Clearances and Aircraft Separation provide standard separation only between IFR flights. 4−4−2. Clearance Prefix A clearance, control information, or a response to a request for information originated by an ATC facility and relayed to the pilot through an air−to−ground communication station will be prefixed by “ATC clears,” “ATC advises,” or “ATC requests.” 4−4−3. Clearance Items ATC clearances normally contain the following: a. Clearance Limit. The traffic clearance issued prior to departure will normally authorize flight to the airport of intended landing. Many airports and associated NAVAIDs are collocated with the same name and/or identifier, so care should be exercised to ensure a clear understanding of the clearance limit. When the clearance limit is the airport of intended landing, the clearance should contain the airport name followed by the word “airport.” Under certain conditions, a clearance limit may be a NAVAID or other fix. When the clearance limit is a NAVAID, intersection, or waypoint and the type is known, the clearance should contain type. Under certain conditions, at some locations a short−range clearance procedure is utilized whereby a clearance is issued to a fix within or just outside of the terminal area and pilots are advised of the frequency on which they will receive the long−range clearance direct from the center controller. b. Departure Procedure. Headings to fly and altitude restrictions may be issued to separate a departure from other air traffic in the terminal area. Where the volume of traffic warrants, DPs have been developed. REFERENCE− AIM, Paragraph 5−2−5, Abbreviated IFR Departure Clearance (Cleared. . .as Filed) Procedures AIM, Paragraph 5−2−9 , Instrument Departure Procedures (DP) − Obstacle Departure Procedures (ODP) and Standard Instrument Departures (SID) c. Route of Flight. 1. Clearances are normally issued for the altitude or flight level and route filed by the pilot. However, due to traffic conditions, it is frequently necessary for ATC to specify an altitude or flight level 4−4−1 AIM or route different from that requested by the pilot. In addition, flow patterns have been established in certain congested areas or between congested areas whereby traffic capacity is increased by routing all traffic on preferred routes. Information on these flow patterns is available in offices where preflight briefing is furnished or where flight plans are accepted. 2. When required, air traffic clearances include data to assist pilots in identifying radio reporting points. It is the responsibility of pilots to notify ATC immediately if their radio equipment cannot receive the type of signals they must utilize to comply with their clearance. d. Altitude Data. 1. The altitude or flight level instructions in an ATC clearance normally require that a pilot “MAINTAIN” the altitude or flight level at which the flight will operate when in controlled airspace. Altitude or flight level changes while en route should be requested prior to the time the change is desired. 2. When possible, if the altitude assigned is different from the altitude requested by the pilot, ATC will inform the pilot when to expect climb or descent clearance or to request altitude change from another facility. If this has not been received prior to crossing the boundary of the ATC facility’s area and assignment at a different altitude is still desired, the pilot should reinitiate the request with the next facility. 3. The term “cruise” may be used instead of “MAINTAIN” to assign a block of airspace to a pilot from the minimum IFR altitude up to and including the altitude specified in the cruise clearance. The pilot may level off at any intermediate altitude within this block of airspace. Climb/descent within the block is to be made at the discretion of the pilot. However, once the pilot starts descent and verbally reports leaving an altitude in the block, the pilot may not return to that altitude without additional ATC clearance. REFERENCE− Pilot/Controller Glossary Term− Cruise. e. Holding Instructions. 1. Whenever an aircraft has been cleared to a fix other than the destination airport and delay is expected, it is the responsibility of the ATC controller to issue complete holding instructions (unless the 4−4−2 6/17/21 pattern is charted), an EFC time, and a best estimate of any additional en route/terminal delay. 2. If the holding pattern is charted and the controller doesn’t issue complete holding instructions, the pilot is expected to hold as depicted on the appropriate chart. When the pattern is charted, the controller may omit all holding instructions except the charted holding direction and the statement AS PUBLISHED, e.g., “HOLD EAST AS PUBLISHED.” Controllers must always issue complete holding instructions when pilots request them. NOTE− Only those holding patterns depicted on U.S. government or commercially produced charts which meet FAA requirements should be used. 3. If no holding pattern is charted and holding instructions have not been issued, the pilot should ask ATC for holding instructions prior to reaching the fix. This procedure will eliminate the possibility of an aircraft entering a holding pattern other than that desired by ATC. If unable to obtain holding instructions prior to reaching the fix (due to frequency congestion, stuck microphone, etc.), hold in a standard pattern on the course on which you approached the fix and request further clearance as soon as possible. In this event, the altitude/flight level of the aircraft at the clearance limit will be protected so that separation will be provided as required. 4. When an aircraft is 3 minutes or less from a clearance limit and a clearance beyond the fix has not been received, the pilot is expected to start a speed reduction so that the aircraft will cross the fix, initially, at or below the maximum holding airspeed. 5. When no delay is expected, the controller should issue a clearance beyond the fix as soon as possible and, whenever possible, at least 5 minutes before the aircraft reaches the clearance limit. 6. Pilots should report to ATC the time and altitude/flight level at which the aircraft reaches the clearance limit and report leaving the clearance limit. NOTE− In the event of two−way communications failure, pilots are required to comply with 14 CFR Section 91.185. 4−4−4. Amended Clearances a. Amendments to the initial clearance will be issued at any time an air traffic controller deems such ATC Clearances and Aircraft Separation 6/17/21 action necessary to avoid possible confliction between aircraft. Clearances will require that a flight “hold” or change altitude prior to reaching the point where standard separation from other IFR traffic would no longer exist. NOTE− Some pilots have questioned this action and requested “traffic information” and were at a loss when the reply indicated “no traffic report.” In such cases the controller has taken action to prevent a traffic confliction which would have occurred at a distant point. b. A pilot may wish an explanation of the handling of the flight at the time of occurrence; however, controllers are not able to take time from their immediate control duties nor can they afford to overload the ATC communications channels to furnish explanations. Pilots may obtain an explanation by directing a letter or telephone call to the chief controller of the facility involved. c. Pilots have the privilege of requesting a different clearance from that which has been issued by ATC if they feel that they have information which would make another course of action more practicable or if aircraft equipment limitations or company procedures forbid compliance with the clearance issued. 4−4−5. Coded Departure Route (CDR) a. CDRs provide air traffic control a rapid means to reroute departing aircraft when the filed route is constrained by either weather or congestion. b. CDRs consist of an eight−character designator that represents a route of flight. The first three alphanumeric characters represent the departure airport, characters four through six represent the arrival airport, and the last two characters are chosen by the overlying ARTCC. For example, PITORDN1 is an alternate route from Pittsburgh to Chicago. Participating aircrews may then be re−cleared by air traffic control via the CDR abbreviated clearance, PITORDN1. c. CDRs are updated on the 56 day charting cycle. Participating aircrews must ensure that their CDR is current. d. Traditionally, CDRs have been used by air transport companies that have signed a Memorandum of Agreement with the local air traffic control facility. General aviation customers who wish to participate in ATC Clearances and Aircraft Separation AIM the program may now enter “CDR Capable” in the remarks section of their flight plan. e. When “CDR Capable” is entered into the remarks section of the flight plan the general aviation customer communicates to ATC the ability to decode the current CDR into a flight plan route and the willingness to fly a different route than that which was filed. 4−4−6. Special VFR Clearances a. An ATC clearance must be obtained prior to operating within a Class B, Class C, Class D, or Class E surface area when the weather is less than that required for VFR flight. A VFR pilot may request and be given a clearance to enter, leave, or operate within most Class D and Class E surface areas and some Class B and Class C surface areas in special VFR conditions, traffic permitting, and providing such flight will not delay IFR operations. All special VFR flights must remain clear of clouds. The visibility requirements for special VFR aircraft (other than helicopters) are: 1. At least 1 statute mile flight visibility for operations within Class B, Class C, Class D, and Class E surface areas. 2. At least 1 statute mile ground visibility if taking off or landing. If ground visibility is not reported at that airport, the flight visibility must be at least 1 statute mile. 3. The restrictions in subparagraphs 1 and 2 do not apply to helicopters. Helicopters must remain clear of clouds and may operate in Class B, Class C, Class D, and Class E surface areas with less than 1 statute mile visibility. b. When a control tower is located within the Class B, Class C, or Class D surface area, requests for clearances should be to the tower. In a Class E surface area, a clearance may be obtained from the nearest tower, FSS, or center. c. It is not necessary to file a complete flight plan with the request for clearance, but pilots should state their intentions in sufficient detail to permit ATC to fit their flight into the traffic flow. The clearance will not contain a specific altitude as the pilot must remain clear of clouds. The controller may require the pilot to fly at or below a certain altitude due to other traffic, but the altitude specified will permit flight at or above the minimum safe altitude. In addition, at radar 4−4−3 AIM locations, flights may be vectored if necessary for control purposes or on pilot request. NOTE− The pilot is responsible for obstacle or terrain clearance. REFERENCE− 14 CFR Section 91.119, Minimum safe altitudes: General. d. Special VFR clearances are effective within Class B, Class C, Class D, and Class E surface areas only. ATC does not provide separation after an aircraft leaves the Class B, Class C, Class D, or Class E surface area on a special VFR clearance. e. Special VFR operations by fixed−wing aircraft are prohibited in some Class B and Class C surface areas due to the volume of IFR traffic. A list of these Class B and Class C surface areas is contained in 14 CFR Part 91, Appendix D, Section 3. They are also depicted on sectional aeronautical charts. f. ATC provides separation between Special VFR flights and between these flights and other IFR flights. g. Special VFR operations by fixed−wing aircraft are prohibited between sunset and sunrise unless the pilot is instrument rated and the aircraft is equipped for IFR flight. h. Pilots arriving or departing an uncontrolled airport that has automated weather broadcast capability (ASOS/AWOS) should monitor the broadcast frequency, advise the controller that they have the “one−minute weather” and state intentions prior to operating within the Class B, Class C, Class D, or Class E surface areas. REFERENCE− Pilot/Controller Glossary Term− One−minute Weather. 4−4−7. Pilot Responsibility upon Clearance Issuance a. Record ATC clearance. When conducting an IFR operation, make a written record of your clearance. The specified conditions which are a part of your air traffic clearance may be somewhat different from those included in your flight plan. Additionally, ATC may find it necessary to ADD conditions, such as particular departure route. The very fact that ATC specifies different or additional conditions means that other aircraft are involved in the traffic situation. 4−4−4 6/17/21 b. ATC Clearance/Instruction Readback. Pilots of airborne aircraft should read back those parts of ATC clearances and instructions containing altitude assignments, vectors, or runway assignments as a means of mutual verification. The read back of the “numbers” serves as a double check between pilots and controllers and reduces the kinds of communications errors that occur when a number is either “misheard” or is incorrect. 1. Include the aircraft identification in all readbacks and acknowledgments. This aids controllers in determining that the correct aircraft received the clearance or instruction. The requirement to include aircraft identification in all readbacks and acknowledgements becomes more important as frequency congestion increases and when aircraft with similar call signs are on the same frequency. EXAMPLE− “Climbing to Flight Level three three zero, United Twelve” or “November Five Charlie Tango, roger, cleared to land runway nine left.” 2. Read back altitudes, altitude restrictions, and vectors in the same sequence as they are given in the clearance or instruction. 3. Altitudes contained in charted procedures, such as DPs, instrument approaches, etc., should not be read back unless they are specifically stated by the controller. 4. Initial read back of a taxi, departure or landing clearance should include the runway assignment, including left, right, center, etc. if applicable. c. It is the responsibility of the pilot to accept or refuse the clearance issued. 4−4−8. IFR Clearance VFR−on−top a. A pilot on an IFR flight plan operating in VFR weather conditions, may request VFR−on−top in lieu of an assigned altitude. This permits a pilot to select an altitude or flight level of their choice (subject to any ATC restrictions.) b. Pilots desiring to climb through a cloud, haze, smoke, or other meteorological formation and then either cancel their IFR flight plan or operate VFR-on-top may request a climb to VFR-on-top. The ATC authorization must contain either a top report or a statement that no top report is available, and a request to report reaching VFR-on-top. Additionally, the ATC authorization may contain a clearance limit, ATC Clearances and Aircraft Separation 12/2/21 6/17/21 AIM routing and an alternative clearance if VFR−on−top is not reached by a specified altitude. h. ATC will not authorize VFR or VFR−on−top operations in Class A airspace. c. A pilot on an IFR flight plan, operating in VFR conditions, may request to climb/descend in VFR conditions. REFERENCE− AIM, Paragraph 3−2−2, Class A Airspace d. ATC may not authorize VFR−on−top/VFR conditions operations unless the pilot requests the VFR operation or a clearance to operate in VFR conditions will result in noise abatement benefits where part of the IFR departure route does not conform to an FAA approved noise abatement route or altitude. e. When operating in VFR conditions with an ATC authorization to “maintain VFR−on−top/maintain VFR conditions” pilots on IFR flight plans must: 1. Fly at the appropriate VFR altitude as prescribed in 14 CFR Section 91.159. 2. Comply with the VFR visibility and distance from cloud criteria in 14 CFR Section 91.155 (Basic VFR Weather Minimums). 3. Comply with instrument flight rules that are applicable to this flight; i.e., minimum IFR altitudes, position reporting, radio communications, course to be flown, adherence to ATC clearance, etc. NOTE− Pilots should advise ATC prior to any altitude change to ensure the exchange of accurate traffic information. f. ATC authorization to “maintain VFR−on−top” is not intended to restrict pilots so that they must operate only above an obscuring meteorological formation (layer). Instead, it permits operation above, below, between layers, or in areas where there is no meteorological obscuration. It is imperative, however, that pilots understand that clearance to operate “VFR−on−top/VFR conditions” does not imply cancellation of the IFR flight plan. g. Pilots operating VFR−on−top/VFR conditions may receive traffic information from ATC on other pertinent IFR or VFR aircraft. However, aircraft operating in Class B airspace/TRSAs must be separated as required by FAA Order JO 7110.65, Air Traffic Control. NOTE− When operating in VFR weather conditions, it is the pilot’s responsibility to be vigilant so as to see−and−avoid other aircraft. ATC Clearances and Aircraft Separation 4−4−9. VFR/IFR Flights A pilot departing VFR, either intending to or needing to obtain an IFR clearance en route, must be aware of the position of the aircraft and the relative terrain/obstructions. When accepting a clearance below the MEA/MIA/MVA/OROCA, pilots are responsible for their own terrain/obstruction clearance until reaching the MEA/MIA/MVA/OROCA. If pilots are unable to maintain terrain/obstruction clearance, the controller should be advised and pilots should state their intentions. NOTE− OROCA is a published altitude which provides 1,000 feet of terrain and obstruction clearance in the US (2,000 feet of clearance in designated mountainous areas). These altitudes are not assessed for NAVAID signal coverage, air traffic control surveillance, or communications coverage, and are published for general situational awareness, flight planning and in−flight contingency use. 4−4−10. Adherence to Clearance a. When air traffic clearance has been obtained under either visual or instrument flight rules, the pilot−in−command of the aircraft must not deviate from the provisions thereof unless an amended clearance is obtained. When ATC issues a clearance or instruction, pilots are expected to execute its provisions upon receipt. ATC, in certain situations, will include the word “IMMEDIATELY” in a clearance or instruction to impress urgency of an imminent situation and expeditious compliance by the pilot is expected and necessary for safety. The addition of a VFR or other restriction; i.e., climb or descent point or time, crossing altitude, etc., does not authorize a pilot to deviate from the route of flight or any other provision of the ATC clearance. b. When a heading is assigned or a turn is requested by ATC, pilots are expected to promptly initiate the turn, to complete the turn, and maintain the new heading unless issued additional instructions. c. The term “AT PILOT’S DISCRETION” included in the altitude information of an ATC clearance means that ATC has offered the pilot the option to start climb or descent when the pilot wishes, 4−4−5 AIM is authorized to conduct the climb or descent at any rate, and to temporarily level off at any intermediate altitude as desired. However, once the aircraft has vacated an altitude, it may not return to that altitude. d. When ATC has not used the term “AT PILOT’S DISCRETION” nor imposed any climb or descent restrictions, pilots should initiate climb or descent promptly on acknowledgement of the clearance. Descend or climb at an optimum rate consistent with the operating characteristics of the aircraft to 1,000 feet above or below the assigned altitude, and then attempt to descend or climb at a rate of between 500 and 1,500 fpm until the assigned altitude is reached. If at anytime the pilot is unable to climb or descend at a rate of at least 500 feet a minute, advise ATC. If it is necessary to level off at an intermediate altitude during climb or descent, advise ATC, except when leveling off at 10,000 feet MSL on descent, or 2,500 feet above airport elevation (prior to entering a Class C or Class D surface area), when required for speed reduction. REFERENCE− 14 CFR Section 91.117. NOTE− Leveling off at 10,000 feet MSL on descent or 2,500 feet above airport elevation (prior to entering a Class C or Class D surface area) to comply with 14 CFR Section 91.117 airspeed restrictions is commonplace. Controllers anticipate this action and plan accordingly. Leveling off at any other time on climb or descent may seriously affect air traffic handling by ATC. Consequently, it is imperative that pilots make every effort to fulfill the above expected actions to aid ATC in safely handling and expediting traffic. e. If the altitude information of an ATC DESCENT clearance includes a provision to “CROSS (fix) AT” or “AT OR ABOVE/BELOW (altitude),” the manner in which the descent is executed to comply with the crossing altitude is at the pilot’s discretion. This authorization to descend at pilot’s discretion is only applicable to that portion of the flight to which the crossing altitude restriction applies, and the pilot is expected to comply with the crossing altitude as a provision of the clearance. Any other clearance in which pilot execution is optional will so state “AT PILOT’S DISCRETION.” EXAMPLE− 1. “United Four Seventeen, descend and maintain six thousand.” 4−4−6 6/17/21 NOTE− 1. The pilot is expected to commence descent upon receipt of the clearance and to descend at the suggested rates until reaching the assigned altitude of 6,000 feet. EXAMPLE− 2. “United Four Seventeen, descend at pilot’s discretion, maintain six thousand.” NOTE− 2. The pilot is authorized to conduct descent within the context of the term at pilot’s discretion as described above. EXAMPLE− 3. “United Four Seventeen, cross Lakeview V−O−R at or above Flight Level two zero zero, descend and maintain six thousand.” NOTE− 3. The pilot is authorized to conduct descent at pilot’s discretion until reaching Lakeview VOR and must comply with the clearance provision to cross the Lakeview VOR at or above FL 200. After passing Lakeview VOR, the pilot is expected to descend at the suggested rates until reaching the assigned altitude of 6,000 feet. EXAMPLE− 4. “United Four Seventeen, cross Lakeview V−O−R at six thousand, maintain six thousand.” NOTE− 4. The pilot is authorized to conduct descent at pilot’s discretion, however, must comply with the clearance provision to cross the Lakeview VOR at 6,000 feet. EXAMPLE− 5. “United Four Seventeen, descend now to Flight Level two seven zero, cross Lakeview V−O−R at or below one zero thousand, descend and maintain six thousand.” NOTE− 5. The pilot is expected to promptly execute and complete descent to FL 270 upon receipt of the clearance. After reaching FL 270 the pilot is authorized to descend “at pilot’s discretion” until reaching Lakeview VOR. The pilot must comply with the clearance provision to cross Lakeview VOR at or below 10,000 feet. After Lakeview VOR the pilot is expected to descend at the suggested rates until reaching 6,000 feet. EXAMPLE− 6. “United Three Ten, descend now and maintain Flight Level two four zero, pilot’s discretion after reaching Flight Level two eight zero.” NOTE− 6. The pilot is expected to commence descent upon receipt of the clearance and to descend at the suggested rates until reaching FL 280. At that point, the pilot is authorized to continue descent to FL 240 within the context of the term “at pilot’s discretion” as described above. f. In case emergency authority is used to deviate from provisions of an ATC clearance, the pilot−in− ATC Clearances and Aircraft Separation 6/17/21 command must notify ATC as soon as possible and obtain an amended clearance. In an emergency situation which does not result in a deviation from the rules prescribed in 14 CFR Part 91 but which requires ATC to give priority to an aircraft, the pilot of such aircraft must, when requested by ATC, make a report within 48 hours of such emergency situation to the manager of that ATC facility. g. The guiding principle is that the last ATC clearance has precedence over the previous ATC clearance. When the route or altitude in a previously issued clearance is amended, the controller will restate applicable altitude restrictions. If altitude to maintain is changed or restated, whether prior to departure or while airborne, and previously issued altitude restrictions are omitted, those altitude restrictions are canceled, including departure procedures and STAR altitude restrictions. EXAMPLE− 1. A departure flight receives a clearance to destination airport to maintain FL 290. The clearance incorporates a DP which has certain altitude crossing restrictions. Shortly after takeoff, the flight receives a new clearance changing the maintaining FL from 290 to 250. If the altitude restrictions are still applicable, the controller restates them. 2. A departing aircraft is cleared to cross Fluky Intersection at or above 3,000 feet, Gordonville VOR at or above 12,000 feet, maintain FL 200. Shortly after departure, the altitude to be maintained is changed to FL 240. If the altitude restrictions are still applicable, the controller issues an amended clearance as follows: “cross Fluky Intersection at or above three thousand, cross Gordonville V−O−R at or above one two thousand, maintain Flight Level two four zero.” 3. An arriving aircraft is cleared to the destination airport via V45 Delta VOR direct; the aircraft is cleared to cross Delta VOR at 10,000 feet, and then to maintain 6,000 feet. Prior to Delta VOR, the controller issues an amended clearance as follows: “turn right heading one eight zero for vector to runway three six I−L−S approach, maintain six thousand.” NOTE− Because the altitude restriction “cross Delta V−O−R at 10,000 feet” was omitted from the amended clearance, it is no longer in effect. h. Pilots of turbojet aircraft equipped with afterburner engines should advise ATC prior to takeoff if they intend to use afterburning during their climb to the en route altitude. Often, the controller ATC Clearances and Aircraft Separation AIM may be able to plan traffic to accommodate a high performance climb and allow the aircraft to climb to the planned altitude without restriction. i. If an “expedite” climb or descent clearance is issued by ATC, and the altitude to maintain is subsequently changed or restated without an expedite instruction, the expedite instruction is canceled. Expedite climb/descent normally indicates to the pilot that the approximate best rate of climb/descent should be used without requiring an exceptional change in aircraft handling characteristics. Normally controllers will inform pilots of the reason for an instruction to expedite. 4−4−11. IFR Separation Standards a. ATC effects separation of aircraft vertically by assigning different altitudes; longitudinally by providing an interval expressed in time or distance between aircraft on the same, converging, or crossing courses, and laterally by assigning different flight paths. b. Separation will be provided between all aircraft operating on IFR flight plans except during that part of the flight (outside Class B airspace or a TRSA) being conducted on a VFR−on−top/VFR conditions clearance. Under these conditions, ATC may issue traffic advisories, but it is the sole responsibility of the pilot to be vigilant so as to see and avoid other aircraft. c. When radar is employed in the separation of aircraft at the same altitude, a minimum of 3 miles separation is provided between aircraft operating within 40 miles of the radar antenna site, and 5 miles between aircraft operating beyond 40 miles from the antenna site. These minima may be increased or decreased in certain specific situations. NOTE− Certain separation standards are increased in the terminal environment when CENRAP is being utilized. 4−4−12. Speed Adjustments a. ATC will issue speed adjustments to pilots of radar−controlled aircraft to achieve or maintain appropriate spacing. If necessary, ATC will assign a speed when approving deviations or radar vectoring off procedures that include published speed restrictions. If no speed is assigned, speed becomes pilot’s discretion. However, when the aircraft reaches the end of the STAR, the last published speed on the STAR must be maintained until ATC deletes it, 4−4−7 AIM 6/17/21 assigns a new speed, issues a vector, assigns a direct route, or issues an approach clearance. b. ATC will express all speed adjustments in terms of knots based on indicated airspeed (IAS) in 5 or 10 knot increments except that at or above FL 240 speeds may be expressed in terms of Mach numbers in 0.01 increments. The use of Mach numbers is restricted to turbojet aircraft with Mach meters. c. Pilots complying with speed adjustments (published or assigned) are expected to maintain a speed within plus or minus 10 knots or 0.02 Mach number of the specified speed. d. When ATC assigns speed adjustments, it will be in accordance with the following recommended minimums: 1. To aircraft operating between FL 280 and 10,000 feet, a speed not less than 250 knots or the equivalent Mach number. NOTE− 1. On a standard day the Mach numbers equivalent to 250 knots CAS (subject to minor variations) are: FL 240−0.6 FL 250−0.61 FL 260−0.62 FL 270−0.64 FL 280−0.65 FL 290−0.66. 2. When an operational advantage will be realized, speeds lower than the recommended minima may be applied. 2. To arriving turbojet aircraft operating below 10,000 feet: (a) A speed not less than 210 knots, except; (b) Within 20 flying miles of the airport of intended landing, a speed not less than 170 knots. 3. To arriving reciprocating engine or turboprop aircraft within 20 flying miles of the runway threshold of the airport of intended landing, a speed not less than 150 knots. 4. To departing aircraft: e. When ATC combines a speed adjustment with a descent clearance, the sequence of delivery, with the word “then” between, indicates the expected order of execution. EXAMPLE− 1. Descend and maintain (altitude); then, reduce speed to (speed). 2. Reduce speed to (speed); then, descend and maintain (altitude). NOTE− The maximum speeds below 10,000 feet as established in 14 CFR Section 91.117 still apply. If there is any doubt concerning the manner in which such a clearance is to be executed, request clarification from ATC. f. If ATC determines (before an approach clearance is issued) that it is no longer necessary to apply speed adjustment procedures, they will: 1. Advise the pilot to “resume normal speed.” Normal speed is used to terminate ATC assigned speed adjustments on segments where no published speed restrictions apply. It does not cancel published restrictions on upcoming procedures. This does not relieve the pilot of those speed restrictions which are applicable to 14 CFR Section 91.117. EXAMPLE− (An aircraft is flying a SID with no published speed restrictions. ATC issues a speed adjustment and instructs the aircraft where the adjustment ends): “Maintain two two zero knots until BALTR then resume normal speed.” NOTE− The ATC assigned speed assignment of two two zero knots would apply until BALTR. The aircraft would then resume a normal operating speed while remaining in compliance with 14 CFR Section 91.117. 2. Instruct pilots to “comply with speed restrictions” when the aircraft is joining or resuming a charted procedure or route with published speed restrictions. EXAMPLE− (ATC vectors an aircraft off of a SID to rejoin the procedure at a subsequent waypoint. When instructing the aircraft to resume the procedure, ATC also wants the aircraft to comply with the published procedure speed restrictions): “Resume the SALTY ONE departure. Comply with speed restrictions.” (a) Turbojet aircraft, a speed not less than 230 knots. CAUTION− The phraseology “Descend via/Climb via SID” requires compliance with all altitude and/or speed restrictions depicted on the procedure. (b) Reciprocating engine aircraft, a speed not less than 150 knots. 3. Instruct the pilot to “resume published speed.” Resume published speed is issued to 4−4−8 ATC Clearances and Aircraft Separation 6/17/21 terminate a speed adjustment where speed restrictions are published on a charted procedure. NOTE− When instructed to “comply with speed restrictions” or to “resume published speed,” ATC anticipates pilots will begin adjusting speed the minimum distance necessary prior to a published speed restriction so as to cross the waypoint/fix at the published speed. Once at the published speed, ATC expects pilots will maintain the published speed until additional adjustment is required to comply with further published or ATC assigned speed restrictions or as required to ensure compliance with 14 CFR Section 91.117. EXAMPLE− (An aircraft is flying a SID/STAR with published speed restrictions. ATC issues a speed adjustment and instructs the aircraft where the adjustment ends): “Maintain two two zero knots until BALTR then resume published speed.” NOTE− The ATC assigned speed assignment of two two zero knots would apply until BALTR. The aircraft would then comply with the published speed restrictions. 4. Advise the pilot to “delete speed restrictions” when either ATC assigned or published speed restrictions on a charted procedure are no longer required. EXAMPLE− (An aircraft is flying a SID with published speed restrictions designed to prevent aircraft overtake on departure. ATC determines there is no conflicting traffic and deletes the speed restriction): “Delete speed restrictions.” NOTE− When deleting published restrictions, ATC must ensure obstacle clearance until aircraft are established on a route where no published restrictions apply. This does not relieve the pilot of those speed restrictions which are applicable to 14 CFR Section 91.117. 5. Instruct the pilot to “climb via” or “descend via.” A climb via or descend via clearance cancels any previously issued speed restrictions and, once established on the depicted departure or arrival, to climb or descend, and to meet all published or assigned altitude and/or speed restrictions. EXAMPLE− 1. (An aircraft is flying a SID with published speed restrictions. ATC has issued a speed restriction of 250 knots for spacing. ATC determines that spacing between aircraft is adequate and desires the aircraft to comply with published restrictions): “United 436, Climb via SID.” ATC Clearances and Aircraft Separation AIM 2. (An aircraft is established on a STAR. ATC must slow an aircraft for the purposes of spacing and assigns it a speed of 280 knots. When spacing is adequate, ATC deletes the speed restriction and desires that the aircraft comply with all published restrictions on the STAR): “Gulfstream two three papa echo, descend via the TYLER One arrival.” NOTE− 1. In example 1, when ATC issues a “Climb via SID” clearance, it deletes any previously issued speed and/or altitude restrictions. The pilot should then vertically navigate to comply with all speed and/or altitude restrictions published on the SID. 2. In example 2, when ATC issues a “Descend via <STAR name> arrival,” ATC has canceled any previously issued speed and/or altitude restrictions. The pilot should vertically navigate to comply with all speed and/or altitude restrictions published on the STAR. CAUTION− When descending on a STAR, pilots should not speed up excessively beyond the previously issued speed. Otherwise, adequate spacing between aircraft descending on the STAR that was established by ATC with the previous restriction may be lost. g. Approach clearances supersede any prior speed adjustment assignments, and pilots are expected to make their own speed adjustments as necessary to complete the approach. However, under certain circumstances, it may be necessary for ATC to issue further speed adjustments after approach clearance is issued to maintain separation between successive arrivals. Under such circumstances, previously issued speed adjustments will be restated if that speed is to be maintained or additional speed adjustments are requested. Speed adjustments should not be assigned inside the final approach fix on final or a point 5 miles from the runway, whichever is closer to the runway. h. The pilots retain the prerogative of rejecting the application of speed adjustment by ATC if the minimum safe airspeed for any particular operation is greater than the speed adjustment. NOTE− In such cases, pilots are expected to advise ATC of the speed that will be used. i. Pilots are reminded that they are responsible for rejecting the application of speed adjustment by ATC if, in their opinion, it will cause them to exceed the maximum indicated airspeed prescribed by 14 CFR Section 91.117(a), (c) and (d). IN SUCH CASES, THE PILOT IS EXPECTED TO SO INFORM ATC. 4−4−9 AIM Pilots operating at or above 10,000 feet MSL who are issued speed adjustments which exceed 250 knots IAS and are subsequently cleared below 10,000 feet MSL are expected to comply with 14 CFR Section 91.117(a). j. Speed restrictions of 250 knots do not apply to U.S. registered aircraft operating beyond 12 nautical miles from the coastline within the U.S. Flight Information Region, in Class E airspace below 10,000 feet MSL. However, in airspace underlying a Class B airspace area designated for an airport, or in a VFR corridor designated through such as a Class B airspace area, pilots are expected to comply with the 200 knot speed limit specified in 14 CFR Section 91.117(c). k. For operations in a Class C and Class D surface area, ATC is authorized to request or approve a speed greater than the maximum indicated airspeeds prescribed for operation within that airspace (14 CFR Section 91.117(b)). NOTE− Pilots are expected to comply with the maximum speed of 200 knots when operating beneath Class B airspace or in a Class B VFR corridor (14 CFR Section 91.117(c) and (d)). l. When in communications with the ARTCC or approach control facility, pilots should, as a good operating practice, state any ATC assigned speed restriction on initial radio contact associated with an ATC communications frequency change. 4−4−13. Runway Separation Tower controllers establish the sequence of arriving and departing aircraft by requiring them to adjust flight or ground operation as necessary to achieve proper spacing. They may “HOLD” an aircraft short of the runway to achieve spacing between it and an arriving aircraft; the controller may instruct a pilot to “EXTEND DOWNWIND” in order to establish spacing from an arriving or departing aircraft. At times a clearance may include the word “IMMEDIATE.” For example: “CLEARED FOR IMMEDIATE TAKEOFF.” In such cases “IMMEDIATE” is used for purposes of air traffic separation. It is up to the pilot to refuse the clearance if, in the pilot’s opinion, compliance would adversely affect the operation. REFERENCE− AIM, Paragraph 4−3−15 , Gate Holding due to Departure Delays 4−4−10 6/17/21 4−4−14. Visual Separation a. Visual separation is a means employed by ATC to separate aircraft in terminal areas and en route airspace in the NAS. There are two methods employed to effect this separation: 1. The tower controller sees the aircraft involved and issues instructions, as necessary, to ensure that the aircraft avoid each other. 2. A pilot sees the other aircraft involved and upon instructions from the controller provides separation by maneuvering the aircraft to avoid it. When pilots accept responsibility to maintain visual separation, they must maintain constant visual surveillance and not pass the other aircraft until it is no longer a factor. NOTE− Traffic is no longer a factor when during approach phase the other aircraft is in the landing phase of flight or executes a missed approach; and during departure or en route, when the other aircraft turns away or is on a diverging course. b. A pilot’s acceptance of instructions to follow another aircraft or provide visual separation from it is an acknowledgment that the pilot will maneuver the aircraft as necessary to avoid the other aircraft or to maintain in−trail separation. In operations conducted behind heavy aircraft, or a small aircraft behind a B757 or other large aircraft, it is also an acknowledgment that the pilot accepts the responsibility for wake turbulence separation. Visual separation is prohibited behind super aircraft. NOTE− When a pilot has been told to follow another aircraft or to provide visual separation from it, the pilot should promptly notify the controller if visual contact with the other aircraft is lost or cannot be maintained or if the pilot cannot accept the responsibility for the separation for any reason. c. Scanning the sky for other aircraft is a key factor in collision avoidance. Pilots and copilots (or the right seat passenger) should continuously scan to cover all areas of the sky visible from the cockpit. Pilots must develop an effective scanning technique which maximizes one’s visual capabilities. Spotting a potential collision threat increases directly as more time is spent looking outside the aircraft. One must use timesharing techniques to effectively scan the surrounding airspace while monitoring instruments as well. d. Since the eye can focus only on a narrow viewing area, effective scanning is accomplished ATC Clearances and Aircraft Separation 6/17/21 with a series of short, regularly spaced eye movements that bring successive areas of the sky into the central visual field. Each movement should not exceed ten degrees, and each area should be observed for at least one second to enable collision detection. Although many pilots seem to prefer the method of horizontal back−and−forth scanning every pilot should develop a scanning pattern that is not only comfortable but assures optimum effectiveness. Pilots should remember, however, that they have a regulatory responsibility (14 CFR Section 91.113(a)) to see and avoid other aircraft when weather conditions permit. 4−4−15. Use of Visual Clearing Procedures a. Before Takeoff. Prior to taxiing onto a runway or landing area in preparation for takeoff, pilots should scan the approach areas for possible landing traffic and execute the appropriate clearing maneuvers to provide them a clear view of the approach areas. b. Climbs and Descents. During climbs and descents in flight conditions which permit visual detection of other traffic, pilots should execute gentle banks, left and right at a frequency which permits continuous visual scanning of the airspace about them. c. Straight and Level. Sustained periods of straight and level flight in conditions which permit visual detection of other traffic should be broken at intervals with appropriate clearing procedures to provide effective visual scanning. d. Traffic Pattern. Entries into traffic patterns while descending create specific collision hazards and should be avoided. e. Traffic at VOR Sites. All operators should emphasize the need for sustained vigilance in the vicinity of VORs and airway intersections due to the convergence of traffic. f. Training Operations. Operators of pilot training programs are urged to adopt the following practices: 1. Pilots undergoing flight instruction at all levels should be requested to verbalize clearing procedures (call out “clear” left, right, above, or below) to instill and sustain the habit of vigilance during maneuvering. ATC Clearances and Aircraft Separation AIM 2. High−wing airplane. Momentarily raise the wing in the direction of the intended turn and look. 3. Low−wing airplane. Momentarily lower the wing in the direction of the intended turn and look. 4. Appropriate clearing procedures should precede the execution of all turns including chandelles, lazy eights, stalls, slow flight, climbs, straight and level, spins, and other combination maneuvers. 4−4−16. Traffic Alert and Collision Avoidance System (TCAS I & II) a. TCAS I provides proximity warning only, to assist the pilot in the visual acquisition of intruder aircraft. No recommended avoidance maneuvers are provided nor authorized as a direct result of a TCAS I warning. It is intended for use by smaller commuter aircraft holding 10 to 30 passenger seats, and general aviation aircraft. b. TCAS II provides traffic advisories (TA) and resolution advisories (RA). Resolution advisories provide recommended maneuvers in a vertical direction (climb or descend only) to avoid conflicting traffic. Transport category aircraft, and larger commuter and business aircraft holding 31 passenger seats or more, are required to be TCAS II equipped. 1. When a TA occurs, attempt to establish visual contact with the traffic but do not deviate from an assigned clearance based only on TA information. 2. When an RA occurs, pilots should respond immediately to the RA displays and maneuver as indicated unless doing so would jeopardize the safe operation of the flight, or the flight crew can ensure separation with the help of definitive visual acquisition of the aircraft causing the RA. 3. Each pilot who deviates from an ATC clearance in response to an RA must notify ATC of that deviation as soon as practicable, and notify ATC when clear of conflict and returning to their previously assigned clearance. c. Deviations from rules, policies, or clearances should be kept to the minimum necessary to satisfy an RA. Most RA maneuvering requires minimum excursion from assigned altitude. d. The serving IFR air traffic facility is not responsible to provide approved standard IFR separation to an IFR aircraft, from other aircraft, 4−4−11 AIM 6/17/21 terrain, or obstructions after an RA maneuver until one of the following conditions exists: 1. The aircraft has returned to its assigned altitude and course. 2. Alternate ATC instructions have been issued. 3. A crew member informs ATC that the TCAS maneuver has been completed. NOTE− TCAS does not alter or diminish the pilot’s basic authority and responsibility to ensure safe flight. Since TCAS does not respond to aircraft which are not transponder equipped or aircraft with a transponder failure, TCAS alone does not ensure safe separation in every case. At this time, no air traffic service nor handling is predicated on the availability of TCAS equipment in the aircraft. 4−4−17. Traffic Information Service (TIS) a. TIS provides proximity warning only, to assist the pilot in the visual acquisition of intruder aircraft. 4−4−12 No recommended avoidance maneuvers are provided nor authorized as a direct result of a TIS intruder display or TIS alert. It is intended for use by aircraft in which TCAS is not required. b. TIS does not alter or diminish the pilot’s basic authority and responsibility to ensure safe flight. Since TIS does not respond to aircraft which are not transponder equipped, aircraft with a transponder failure, or aircraft out of radar coverage, TIS alone does not ensure safe separation in every case. c. At this time, no air traffic service nor handling is predicated on the availability of TIS equipment in the aircraft. d. Presently, no air traffic services or handling is predicated on the availability of an ADS−B cockpit display. A “traffic−in−sight” reply to ATC must be based on seeing an aircraft out−the−window, NOT on the cockpit display. ATC Clearances and Aircraft Separation 6/17/21 AIM Section 5. Surveillance Systems 4−5−1. Radar (a) The characteristics of radio waves are such that they normally travel in a continuous straight line unless they are: a. Capabilities 1. Radar is a method whereby radio waves are transmitted into the air and are then received when they have been reflected by an object in the path of the beam. Range is determined by measuring the time it takes (at the speed of light) for the radio wave to go out to the object and then return to the receiving antenna. The direction of a detected object from a radar site is determined by the position of the rotating antenna when the reflected portion of the radio wave is received. 2. More reliable maintenance and improved equipment have reduced radar system failures to a negligible factor. Most facilities actually have some components duplicated, one operating and another which immediately takes over when a malfunction occurs to the primary component. b. Limitations 1. It is very important for the aviation community to recognize the fact that there are limitations to radar service and that ATC controllers may not always be able to issue traffic advisories concerning aircraft which are not under ATC control and cannot be seen on radar. (See FIG 4−5−1.) FIG 4−5−1 Limitations to Radar Service Precipitation Attenuation AREA BLACKED OUT BY ATTENUATION NOT OBSERVED OBSERVED ECHO The nearby target absorbs and scatters so much of the out-going and returning energy that the radar does not detect the distant target. Surveillance Systems (1) “Bent” by abnormal atmospheric phenomena such as temperature inversions; (2) Reflected or attenuated by dense objects such as heavy clouds, precipitation, ground obstacles, mountains, etc.; or (3) Screened by high terrain features. (b) The bending of radar pulses, often called anomalous propagation or ducting, may cause many extraneous blips to appear on the radar operator’s display if the beam has been bent toward the ground or may decrease the detection range if the wave is bent upward. It is difficult to solve the effects of anomalous propagation, but using beacon radar and electronically eliminating stationary and slow moving targets by a method called moving target indicator (MTI) usually negate the problem. (c) Radar energy that strikes dense objects will be reflected and displayed on the operator’s scope thereby blocking out aircraft at the same range and greatly weakening or completely eliminating the display of targets at a greater range. Again, radar beacon and MTI are very effectively used to combat ground clutter and weather phenomena, and a method of circularly polarizing the radar beam will eliminate some weather returns. A negative characteristic of MTI is that an aircraft flying a speed that coincides with the canceling signal of the MTI (tangential or “blind” speed) may not be displayed to the radar controller. (d) Relatively low altitude aircraft will not be seen if they are screened by mountains or are below the radar beam due to earth curvature. The historical solution to screening has been the installation of strategically placed multiple radars, which has been done in some areas, but ADS−B now provides ATC surveillance in some areas with challenging terrain where multiple radar installations would be impractical. (e) There are several other factors which affect radar control. The amount of reflective surface of an aircraft will determine the size of the radar return. Therefore, a small light airplane or a sleek jet 4−5−1 AIM fighter will be more difficult to see on primary radar than a large commercial jet or military bomber. Here again, the use of transponder or ADS−B equipment is invaluable. In addition, all FAA ATC facilities display automatically reported altitude information to the controller from appropriately equipped aircraft. (f) At some locations within the ATC en route environment, secondary−radar−only (no primary radar) gap filler radar systems are used to give lower altitude radar coverage between two larger radar systems, each of which provides both primary and secondary radar coverage. ADS−B serves this same role, supplementing both primary and secondary radar. In those geographical areas served by secondary radar only or ADS−B, aircraft without either transponders or ADS−B equipment cannot be provided with radar service. Additionally, transponder or ADS−B equipped aircraft cannot be provided with radar advisories concerning primary targets and ATC radar−derived weather. REFERENCE− Pilot/Controller Glossary Term− Radar. (g) The controller’s ability to advise a pilot flying on instruments or in visual conditions of the aircraft’s proximity to another aircraft will be limited if the unknown aircraft is not observed on radar, if no flight plan information is available, or if the volume of traffic and workload prevent issuing traffic information. The controller’s first priority is given to establishing vertical, lateral, or longitudinal separation between aircraft flying IFR under the control of ATC. c. FAA radar units operate continuously at the locations shown in the Chart Supplement U.S., and their services are available to all pilots, both civil and military. Contact the associated FAA control tower or ARTCC on any frequency guarded for initial instructions, or in an emergency, any FAA facility for information on the nearest radar service. 4−5−2. Air Traffic Control Radar Beacon System (ATCRBS) a. The ATCRBS, sometimes referred to as secondary surveillance radar, consists of three main components: 1. Interrogator. Primary radar relies on a signal being transmitted from the radar antenna site and for this signal to be reflected or “bounced back” 4−5−2 6/17/21 from an object (such as an aircraft). This reflected signal is then displayed as a “target” on the controller’s radarscope. In the ATCRBS, the Interrogator, a ground based radar beacon transmitter−receiver, scans in synchronism with the primary radar and transmits discrete radio signals which repetitiously request all transponders, on the mode being used, to reply. The replies received are then mixed with the primary returns and both are displayed on the same radarscope. 2. Transponder. This airborne radar beacon transmitter−receiver automatically receives the signals from the interrogator and selectively replies with a specific pulse group (code) only to those interrogations being received on the mode to which it is set. These replies are independent of, and much stronger than a primary radar return. 3. Radarscope. The radarscope used by the controller displays returns from both the primary radar system and the ATCRBS. These returns, called targets, are what the controller refers to in the control and separation of traffic. b. The job of identifying and maintaining identification of primary radar targets is a long and tedious task for the controller. Some of the advantages of ATCRBS over primary radar are: 1. Reinforcement of radar targets. 2. Rapid target identification. 3. Unique display of selected codes. c. A part of the ATCRBS ground equipment is the decoder. This equipment enables a controller to assign discrete transponder codes to each aircraft under his/her control. Normally only one code will be assigned for the entire flight. Assignments are made by the ARTCC computer on the basis of the National Beacon Code Allocation Plan. The equipment is also designed to receive Mode C altitude information from the aircraft. NOTE− Refer to figures with explanatory legends for an illustration of the target symbology depicted on radar scopes in the NAS Stage A (en route), the ARTS III (terminal) Systems, and other nonautomated (broadband) radar systems. (See FIG 4−5−2 and FIG 4−5−3.) d. It should be emphasized that aircraft transponders greatly improve the effectiveness of radar systems. REFERENCE− AIM, Paragraph 4−1−20 , Transponder and ADS−B Out Operation Surveillance Systems 6/17/21 AIM FIG 4−5−2 ARTS III Radar Scope With Alphanumeric Data NOTE− A number of radar terminals do not have ARTS equipment. Those facilities and certain ARTCCs outside the contiguous U.S. would have radar displays similar to the lower right hand subset. ARTS facilities and NAS Stage A ARTCCs, when operating in the nonautomation mode, would also have similar displays and certain services based on automation may not be available. Surveillance Systems 4−5−3 AIM 6/17/21 EXAMPLE− 5. Radar limit line for control 25. “Low ALT” flashes to indicate when an aircraft’s predicted descent places the aircraft in an unsafe proximity to terrain. (Note: this feature does not function if the aircraft is not squawking Mode C. When a helicopter or aircraft is known to be operating below the lower safe limit, the “low ALT” can be changed to “inhibit” and flashing ceases.) 6. Obstruction (video map) 26. NAVAIDs 7. Primary radar returns of obstacles or terrain (can be removed by MTI) 27. Airways 1. Areas of precipitation (can be reduced by CP) 2. Arrival/departure tabular list 3. Trackball (control) position symbol (A) 4. Airway (lines are sometimes deleted in part) 8. Satellite airports 9. Runway centerlines (marks and spaces indicate miles) 10. Primary airport with parallel runways 11. Approach gates 12. Tracked target (primary and beacon target) 13. Control position symbol 14. Untracked target select code (monitored) with Mode C readout of 5,000’ 28. Primary target only 29. Nonmonitored. No Mode C (an asterisk would indicate nonmonitored with Mode C) 30. Beacon target only (secondary radar based on aircraft transponder) 31. Tracked target (primary and beacon target) control position A 32. Aircraft is squawking emergency Code 7700 and is nonmonitored, untracked, Mode C 15. Untracked target without Mode C 33. Controller assigned runway 36 right alternates with Mode C readout (Note: a three letter identifier could also indicate the arrival is at specific airport) 16. Primary target 34. Ident flashes 17. Beacon target only (secondary radar) (transponder) 35. Identing target blossoms 18. Primary and beacon target 36. Untracked target identing on a selected code 19. Leader line 37. Range marks (10 and 15 miles) (can be changed/offset) 20. Altitude Mode C readout is 6,000’ (Note: readouts may not be displayed because of nonreceipt of beacon information, garbled beacon signals, and flight plan data which is displayed alternately with the altitude readout) 21. Ground speed readout is 240 knots (Note: readouts may not be displayed because of a loss of beacon signal, a controller alert that a pilot was squawking emergency, radio failure, etc.) 22. Aircraft ID 23. Asterisk indicates a controller entry in Mode C block. In this case 5,000’ is entered and “05” would alternate with Mode C readout. 24. Indicates heavy 38. Aircraft controlled by center 39. Targets in suspend status 40. Coast/suspend list (aircraft holding, temporary loss of beacon/target, etc.) 41. Radio failure (emergency information) 42. Select beacon codes (being monitored) 43. General information (ATIS, runway, approach in use) 44. Altimeter setting 45. Time 46. System data area 4−5−4 Surveillance Systems 6/17/21 AIM FIG 4−5−3 NAS Stage A Controllers View Plan Display This figure illustrates the controller’s radar scope (PVD) when operating in the full automation (RDP) mode, which is normally 20 hours per day. (When not in automation mode, the display is similar to the broadband mode shown in the ARTS III radar scope figure. Certain ARTCCs outside the contiguous U.S. also operate in “broadband” mode.) RADAR SERVICES AND PROCEDURES 22 21 23 5 30 20 1200 85 19 10 11 AAL373 280C 191H-33 12 6 X UAL33 100A 296 28 3 VIG123 310N 095 1200 7600 RDOF 29 7700 EMRG X 7 H H H X X 2 X N1467F 140 + 143 460 X 1 H H H H X X X + 14 UAL712 310N 228CST 15 # AAL353 70 231 2734 16 X 4 13 X H H H H H H +++ 18 R15909 170C 290 2103 29 26 17 8 X 24 27 Surveillance Systems NWA258 170 143 25 9 4−5−5 AIM 6/17/21 EXAMPLE− Target symbols: 1. Uncorrelated primary radar target [] [+] 16. Assigned altitude 7,000, aircraft is descending, last Mode C readout (or last reported altitude) was 100’ above FL 230 2. Correlated primary radar target [ ] See note below. 17. Transponder code shows in full data block only when different than assigned code 3. Uncorrelated beacon target [ / ] 18. Aircraft is 300’ above assigned altitude 4. Correlated beacon target [ \ ] 19. Reported altitude (no Mode C readout) same as assigned. (An “n” would indicate no reported altitude.) 5. Identing beacon target [] Note: in Number 2 correlated means the association of radar data with the computer projected track of an identified aircraft. 21. Transponder Code 1200 (VFR) with no Mode C 22. Code 1200 (VFR) with Mode C and last altitude readout Position symbols: 6. Free track (no flight plan tracking) [] 7. Flat track (flight plan tracking) [] 8. Coast (beacon target lost) [#] 9. Present position hold [ 20. Transponder set on emergency Code 7700 (EMRG flashes to attract attention) ] 23. Transponder set on radio failure Code 7600 (RDOF flashes) 24. Computer ID #228, CST indicates target is in coast status Data block information: 25. Assigned altitude FL 290, transponder code (these two items constitute a “limited data block”) 10. Aircraft ident See note below. Note: numbers 10, 11, and 12 constitute a “full data block” 11. Assigned altitude FL 280, Mode C altitude same or within 200’ of assigned altitude. See note below. Other symbols: 12. Computer ID #191, handoff is to sector 33 (0−33 would mean handoff accepted) See note below. 27. Airway or jet route 13. Assigned altitude 17,000’, aircraft is climbing, Mode C readout was 14,300 when last beacon interrogation was received. 14. Leader line connecting target symbol and data block 15. Track velocity and direction vector line (projected ahead of target) 4−5−6 26. Navigational aid 28. Outline of weather returns based on primary radar. “H” represents areas of high density precipitation which might be thunderstorms. Radial lines indicated lower density precipitation. 29. Obstruction 30. Airports Major: Small: Surveillance Systems 6/17/21 4−5−3. Surveillance Radar a. Surveillance radars are divided into two general categories: Airport Surveillance Radar (ASR) and Air Route Surveillance Radar (ARSR). 1. ASR is designed to provide relatively short−range coverage in the general vicinity of an airport and to serve as an expeditious means of handling terminal area traffic through observation of precise aircraft locations on a radarscope. The ASR can also be used as an instrument approach aid. 2. ARSR is a long−range radar system designed primarily to provide a display of aircraft locations over large areas. 3. Center Radar Automated Radar Terminal Systems (ARTS) Processing (CENRAP) was developed to provide an alternative to a nonradar environment at terminal facilities should an ASR fail or malfunction. CENRAP sends aircraft radar beacon target information to the ASR terminal facility equipped with ARTS. Procedures used for the separation of aircraft may increase under certain conditions when a facility is utilizing CENRAP because radar target information updates at a slower rate than the normal ASR radar. Radar services for VFR aircraft are also limited during CENRAP operations because of the additional workload required to provide services to IFR aircraft. b. Surveillance radars scan through 360 degrees of azimuth and present target information on a radar display located in a tower or center. This information is used independently or in conjunction with other navigational aids in the control of air traffic. 4−5−4. Precision Approach Radar (PAR) a. PAR is designed for use as a landing aid rather than an aid for sequencing and spacing aircraft. PAR equipment may be used as a primary landing aid (See Chapter 5, Air Traffic Procedures, for additional information), or it may be used to monitor other types of approaches. It is designed to display range, azimuth, and elevation information. b. Two antennas are used in the PAR array, one scanning a vertical plane, and the other scanning Surveillance Systems AIM horizontally. Since the range is limited to 10 miles, azimuth to 20 degrees, and elevation to 7 degrees, only the final approach area is covered. Each scope is divided into two parts. The upper half presents altitude and distance information, and the lower half presents azimuth and distance. 4−5−5. Airport Surface Detection Equipment (ASDE−X)/Airport Surface Surveillance Capability (ASSC) a. ASDE−X/ASSC is a multi−sensor surface surveillance system the FAA is acquiring for airports in the United States. This system provides high resolution, short−range, clutter free surveillance information about aircraft and vehicles, both moving and fixed, located on or near the surface of the airport’s runways and taxiways under all weather and visibility conditions. The system consists of: 1. A Primary Radar System. ASDE−X/ ASSC system coverage includes the airport surface and the airspace up to 200 feet above the surface. Typically located on the control tower or other strategic location on the airport, the Primary Radar antenna is able to detect and display aircraft that are not equipped with or have malfunctioning transponders or ADS−B. 2. Interfaces. ASDE−X/ASSC contains an automation interface for flight identification via all automation platforms and interfaces with the terminal radar for position information. 3. Automation. A Multi−sensor Data Processor (MSDP) combines all sensor reports into a single target which is displayed to the air traffic controller. 4. Air Traffic Control Tower Display. A high resolution, color monitor in the control tower cab provides controllers with a seamless picture of airport operations on the airport surface. b. The combination of data collected from the multiple sensors ensures that the most accurate information about aircraft location is received in the tower, thereby increasing surface safety and efficiency. 4−5−7 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 c. The following facilities are operational with ASDE−X: d. The following facilities have been projected to receive ASSC: TBL 4−5−2 TBL 4−5−1 SFO CLE BWI BOS BDL MDW ORD CLT DFW DEN DTW FLL MKE IAH ATL HNL JFK SNA LGA STL LAS LAX SDF MEM MIA MSP EWR MCO PHL PHX DCA SAN SLC SEA PVD IAD HOU 4−5−8 Baltimore Washington International Boston Logan International Bradley International Chicago Midway Chicago O’Hare International Charlotte Douglas International Dallas/Fort Worth International Denver International Detroit Metro Wayne County Fort Lauderdale/Hollywood Intl General Mitchell International George Bush International Hartsfield−Jackson Atlanta Intl Honolulu International John F. Kennedy International John Wayne−Orange County LaGuardia Lambert St. Louis International Las Vegas Harry Reid International Los Angeles International Louisville International Memphis International Miami International Minneapolis St. Paul International Newark International Orlando International Philadelphia International Phoenix Sky Harbor International Ronald Reagan Washington National San Diego International Salt Lake City International Seattle−Tacoma International Theodore Francis Green State Washington Dulles International William P. Hobby International MCI CVG PDX MSY PIT ANC ADW San Francisco International Cleveland−Hopkins International Kansas City International Cincinnati/Northern Kentucky Intl Portland International Louis Armstrong New Orleans Intl Pittsburgh International Ted Stevens Anchorage International Joint Base Andrews AFB 4−5−6. Traffic Information Service (TIS) a. Introduction. The Traffic Information Service (TIS) provides information to the cockpit via data link, that is similar to VFR radar traffic advisories normally received over voice radio. Among the first FAA−provided data services, TIS is intended to improve the safety and efficiency of “see and avoid” flight through an automatic display that informs the pilot of nearby traffic and potential conflict situations. This traffic display is intended to assist the pilot in visual acquisition of these aircraft. TIS employs an enhanced capability of the terminal Mode S radar system, which contains the surveillance data, as well as the data link required to “uplink” this information to suitably−equipped aircraft (known as a TIS “client”). TIS provides estimated position, altitude, altitude trend, and ground track information for up to 8 intruder aircraft within 7 NM horizontally, +3,500 and −3,000 feet vertically of the client aircraft (see FIG 4−5−4, TIS Proximity Coverage Volume). The range of a target reported at a distance greater than 7 NM only indicates that this target will be a threat within 34 seconds and does not display a precise distance. TIS will alert the pilot to aircraft (under surveillance of the Mode S radar) that are estimated to be within 34 seconds of potential collision, regardless of distance or altitude. TIS surveillance data is derived from the same radar used by ATC; this data is uplinked to the client aircraft on each radar scan (nominally every 5 seconds). Surveillance Systems 6/17/21 AIM b. Requirements. 1. In order to use TIS, the client and any intruder aircraft must be equipped with the appropriate cockpit equipment and fly within the radar coverage of a Mode S radar capable of providing TIS. Typically, this will be within 55 NM of the sites depicted in FIG 4−5−5, Terminal Mode S Radar Sites. ATC communication is not a requirement to receive TIS, although it may be required by the particular airspace or flight operations in which TIS is being used. FIG 4−5−4 TIS Proximity Coverage Volume FIG 4−5−5 Terminal Mode S Radar Sites Surveillance Systems 4−5−9 AIM 6/17/21 FIG 4−5−6 Traffic Information Service (TIS) Avionics Block Diagram 4−5−10 Surveillance Systems 6/17/21 2. The cockpit equipment functionality required by a TIS client aircraft to receive the service consists of the following (refer to FIG 4−5−6): (a) Mode S data link transponder with altitude encoder. (b) Data link applications processor with TIS software installed. (c) Control−display unit. (d) Optional equipment includes a digital heading source to correct display errors caused by “crab angle” and turning maneuvers. NOTE− Some of the above functions will likely be combined into single pieces of avionics, such as (a) and (b). 3. To be visible to the TIS client, the intruder aircraft must, at a minimum, have an operating transponder (Mode A, C or S). All altitude information provided by TIS from intruder aircraft is derived from Mode C reports, if appropriately equipped. 4. TIS will initially be provided by the terminal Mode S systems that are paired with ASR−9 digital primary radars. These systems are in locations with the greatest traffic densities, thus will provide the greatest initial benefit. The remaining terminal Mode S sensors, which are paired with ASR−7 or ASR−8 analog primary radars, will provide TIS pending modification or relocation of these sites. See FIG 4−5−5, Terminal Mode S Radar Sites, for site locations. There is no mechanism in place, such as NOTAMs, to provide status update on individual radar sites since TIS is a nonessential, supplemental information service. The FAA also operates en route Mode S radars (not illustrated) that rotate once every 12 seconds. These sites will require additional development of TIS before any possible implementation. There are no plans to implement TIS in the en route Mode S radars at the present time. c. Capabilities. 1. TIS provides ground−based surveillance information over the Mode S data link to properly equipped client aircraft to aid in visual acquisition of proximate air traffic. The actual avionics capability of each installation will vary and the supplemental handbook material must be consulted prior to using Surveillance Systems AIM TIS. A maximum of eight (8) intruder aircraft may be displayed; if more than eight aircraft match intruder parameters, the eight “most significant” intruders are uplinked. These “most significant” intruders are usually the ones in closest proximity and/or the greatest threat to the TIS client. 2. TIS, through the Mode S ground sensor, provides the following data on each intruder aircraft: (a) Relative bearing information in 6−degree increments. (b) Relative range information in 1/8 NM to 1 NM increments (depending on range). (c) Relative altitude in 100−foot increments (within 1,000 feet) or 500−foot increments (from 1,000−3,500 feet) if the intruder aircraft has operating altitude reporting capability. (d) Estimated intruder ground track in 45−degree increments. (e) Altitude trend data (level within 500 fpm or climbing/descending >500 fpm) if the intruder aircraft has operating altitude reporting capability. (f) Intruder priority as either an “traffic advisory” or “proximate” intruder. 3. When flying from surveillance coverage of one Mode S sensor to another, the transfer of TIS is an automatic function of the avionics system and requires no action from the pilot. 4. There are a variety of status messages that are provided by either the airborne system or ground equipment to alert the pilot of high priority intruders and data link system status. These messages include the following: (a) Alert. Identifies a potential collision hazard within 34 seconds. This alert may be visual and/or audible, such as a flashing display symbol or a headset tone. A target is a threat if the time to the closest approach in vertical and horizontal coordinates is less than 30 seconds and the closest approach is expected to be within 500 feet vertically and 0.5 nautical miles laterally. (b) TIS Traffic. TIS traffic data is displayed. (c) Coasting. The TIS display is more than 6 seconds old. This indicates a missing uplink from the ground system. When the TIS display information is more than 12 seconds old, the “No Traffic” status will be indicated. 4−5−11 AIM (d) No Traffic. No intruders meet proximate or alert criteria. This condition may exist when the TIS system is fully functional or may indicate “coasting” between 12 and 59 seconds old (see (c) above). (e) TIS Unavailable. The pilot has requested TIS, but no ground system is available. This condition will also be displayed when TIS uplinks are missing for 60 seconds or more. (f) TIS Disabled. The pilot has not requested TIS or has disconnected from TIS. (g) Good−bye. The client aircraft has flown outside of TIS coverage. NOTE− Depending on the avionics manufacturer implementation, it is possible that some of these messages will not be directly available to the pilot. 5. Depending on avionics system design, TIS may be presented to the pilot in a variety of different displays, including text and/or graphics. Voice annunciation may also be used, either alone or in combination with a visual display. FIG 4−5−6, Traffic Information Service (TIS), Avionics Block Diagram, shows an example of a TIS display using symbology similar to the Traffic Alert and Collision Avoidance System (TCAS) installed on most passenger air carrier/commuter aircraft in the U.S. The small symbol in the center represents the client aircraft and the display is oriented “track up,” with the 12 o’clock position at the top. The range rings indicate 2 and 5 NM. Each intruder is depicted by a symbol positioned at the approximate relative bearing and range from the client aircraft. The circular symbol near the center indicates an “alert” intruder and the diamond symbols indicate “proximate” intruders. 6. The inset in the lower right corner of FIG 4−5−6, Traffic Information Service (TIS), Avionics Block Diagram, shows a possible TIS data block display. The following information is contained in this data block: (a) The intruder, located approximately four o’clock, three miles, is a “proximate” aircraft and currently not a collision threat to the client aircraft. This is indicated by the diamond symbol used in this example. 4−5−12 6/17/21 (b) The intruder ground track diverges to the right of the client aircraft, indicated by the small arrow. (c) The intruder altitude is 700 feet less than or below the client aircraft, indicated by the “−07” located under the symbol. (d) The intruder is descending >500 fpm, indicated by the downward arrow next to the “−07” relative altitude information. The absence of this arrow when an altitude tag is present indicates level flight or a climb/descent rate less than 500 fpm. NOTE− If the intruder did not have an operating altitude encoder (Mode C), the altitude and altitude trend “tags” would have been omitted. d. Limitations. 1. TIS is NOT intended to be used as a collision avoidance system and does not relieve the pilot’s responsibility to “see and avoid” other aircraft (see Paragraph 5−5−8, See and Avoid). TIS must not be used for avoidance maneuvers during IMC or other times when there is no visual contact with the intruder aircraft. TIS is intended only to assist in visual acquisition of other aircraft in VMC. Avoidance maneuvers are neither provided nor authorized as a direct result of a TIS intruder display or TIS alert. 2. While TIS is a useful aid to visual traffic avoidance, it has some system limitations that must be fully understood to ensure proper use. Many of these limitations are inherent in secondary radar surveillance. In other words, the information provided by TIS will be no better than that provided to ATC. Other limitations and anomalies are associated with the TIS predictive algorithm. (a) Intruder Display Limitations. TIS will only display aircraft with operating transponders installed. TIS relies on surveillance of the Mode S radar, which is a “secondary surveillance” radar similar to the ATCRBS described in paragraph 4−5−2. (b) TIS Client Altitude Reporting Requirement. Altitude reporting is required by the TIS client aircraft in order to receive TIS. If the altitude encoder is inoperative or disabled, TIS will be unavailable, as TIS requests will not be honored by the ground system. As such, TIS requires altitude reporting to determine the Proximity Coverage Volume as indicated in FIG 4−5−4. TIS users must be alert to Surveillance Systems 12/2/21 6/17/21 altitude encoder malfunctions, as TIS has no mechanism to determine if client altitude reporting is correct. A failure of this nature will cause erroneous and possibly unpredictable TIS operation. If this malfunction is suspected, confirmation of altitude reporting with ATC is suggested. (c) Intruder Altitude Reporting. Intruders without altitude reporting capability will be displayed without the accompanying altitude tag. Additionally, nonaltitude reporting intruders are assumed to be at the same altitude as the TIS client for alert computations. This helps to ensure that the pilot will be alerted to all traffic under radar coverage, but the actual altitude difference may be substantial. Therefore, visual acquisition may be difficult in this instance. (d) Coverage Limitations. Since TIS is provided by ground−based, secondary surveillance radar, it is subject to all limitations of that radar. If an aircraft is not detected by the radar, it cannot be displayed on TIS. Examples of these limitations are as follows: (1) TIS will typically be provided within 55 NM of the radars depicted in FIG 4−5−5, Terminal Mode S Radar Sites. This maximum range can vary by radar site and is always subject to “line of sight” limitations; the radar and data link signals will be blocked by obstructions, terrain, and curvature of the earth. (2) TIS will be unavailable at low altitudes in many areas of the country, particularly in mountainous regions. Also, when flying near the “floor” of radar coverage in a particular area, intruders below the client aircraft may not be detected by TIS. (3) TIS will be temporarily disrupted when flying directly over the radar site providing coverage if no adjacent site assumes the service. A ground−based radar, similar to a VOR or NDB, has a zenith cone, sometimes referred to as the cone of confusion or cone of silence. This is the area of ambiguity directly above the station where bearing information is unreliable. The zenith cone setting for TIS is 34 degrees: Any aircraft above that angle with respect to the radar horizon will lose TIS coverage from that radar until it is below this 34 degree angle. The aircraft may not actually lose service in areas of multiple radar coverage since an adjacent radar will Surveillance Systems AIM provide TIS. If no other TIS−capable radar is available, the “Good−bye” message will be received and TIS terminated until coverage is resumed. (e) Intermittent Operations. TIS operation may be intermittent during turns or other maneuvering, particularly if the transponder system does not include antenna diversity (antenna mounted on the top and bottom of the aircraft). As in (d) above, TIS is dependent on two−way, “line of sight” communications between the aircraft and the Mode S radar. Whenever the structure of the client aircraft comes between the transponder antenna (usually located on the underside of the aircraft) and the ground−based radar antenna, the signal may be temporarily interrupted. (f) TIS Predictive Algorithm. TIS information is collected one radar scan prior to the scan during which the uplink occurs. Therefore, the surveillance information is approximately 5 seconds old. In order to present the intruders in a “real time” position, TIS uses a “predictive algorithm” in its tracking software. This algorithm uses track history data to extrapolate intruders to their expected positions consistent with the time of display in the cockpit. Occasionally, aircraft maneuvering will cause this algorithm to induce errors in the TIS display. These errors primarily affect relative bearing information; intruder distance and altitude will remain relatively accurate and may be used to assist in “see and avoid.” Some of the more common examples of these errors are as follows: (1) When client or intruder aircraft maneuver excessively or abruptly, the tracking algorithm will report incorrect horizontal position until the maneuvering aircraft stabilizes. (2) When a rapidly closing intruder is on a course that crosses the client at a shallow angle (either overtaking or head on) and either aircraft abruptly changes course within ¼ NM, TIS will display the intruder on the opposite side of the client than it actually is. These are relatively rare occurrences and will be corrected in a few radar scans once the course has stabilized. (g) Heading/Course Reference. Not all TIS aircraft installations will have onboard heading reference information. In these installations, aircraft course reference to the TIS display is provided by the Mode S radar. The radar only determines ground 4−5−13 AIM track information and has no indication of the client aircraft heading. In these installations, all intruder bearing information is referenced to ground track and does not account for wind correction. Additionally, since ground−based radar will require several scans to determine aircraft course following a course change, a lag in TIS display orientation (intruder aircraft bearing) will occur. As in (f) above, intruder distance and altitude are still usable. (h) Closely−Spaced Intruder Errors. When operating more than 30 NM from the Mode S sensor, TIS forces any intruder within 3/8 NM of the TIS client to appear at the same horizontal position as the client aircraft. Without this feature, TIS could display intruders in a manner confusing to the pilot in critical situations (for example, a closely−spaced intruder that is actually to the right of the client may appear on the TIS display to the left). At longer distances from the radar, TIS cannot accurately determine relative bearing/distance information on intruder aircraft that are in close proximity to the client. Because TIS uses a ground−based, rotating radar for surveillance information, the accuracy of TIS data is dependent on the distance from the sensor (radar) providing the service. This is much the same phenomenon as experienced with ground−based navigational aids, such as a VOR. As distance from the radar increases, the accuracy of surveillance decreases. Since TIS does not inform the pilot of distance from the Mode S radar, the pilot must assume that any intruder appearing at the same position as the client aircraft may actually be up to 3/8 NM away in any direction. Consistent with the operation of TIS, an alert on the display (regardless of distance from the radar) should stimulate an outside visual scan, intruder acquisition, and traffic avoidance based on outside reference. e. Reports of TIS Malfunctions. 1. Users of TIS can render valuable assistance in the early correction of malfunctions by reporting their observations of undesirable performance. Reporters should identify the time of observation, location, type and identity of aircraft, and describe the condition observed; the type of transponder processor, and software in use can also be useful information. Since TIS performance is monitored by maintenance personnel rather than ATC, it is suggested that 4−5−14 6/17/21 malfunctions be reported by radio or telephone to the nearest Flight Service Station (FSS) facility. NOTE− TIS operates at only those terminal Mode S radar sites depicted in FIG 4−5−5. Though similar in some ways, TIS is not related to TIS−B (Traffic Information Service− Broadcast). 4−5−7. Automatic Dependent Surveillance−Broadcast (ADS−B) Services a. Introduction. 1. Automatic Dependent Surveillance−Broadcast (ADS−B) is a surveillance technology deployed throughout the NAS (see FIG 4−5−7). The ADS−B system is composed of aircraft avionics and a ground infrastructure. Onboard avionics determine the position of the aircraft by using the GNSS and transmit its position along with additional information about the aircraft to ground stations for use by ATC and other ADS−B services. This information is transmitted at a rate of approximately once per second. (See FIG 4−5−8 and FIG 4−5−9.) 2. In the United States, ADS−B equipped aircraft exchange information on one of two frequencies: 978 or 1090 MHz. The 1090 MHz frequency is also associated with Mode A, C, and S transponder operations. 1090 MHz transponders with integrated ADS−B functionality extend the transponder message sets with additional ADS−B information. This additional information is known as an “extended squitter” message and is referred to as 1090ES. ADS−B equipment operating on 978 MHz is known as the Universal Access Transceiver (UAT). 3. ADS−B avionics can have the ability to both transmit and receive information. The transmission of ADS−B information from an aircraft is known as ADS−B Out. The receipt of ADS−B information by an aircraft is known as ADS−B In. All aircraft operating within the airspace defined in 14 CFR § 91.225 are required to transmit the information defined in § 91.227 using ADS−B Out avionics. 4. In general, operators flying at 18,000 feet and above (Class A airspace) are required to have 1090ES equipment. Those that do not fly above 18,000 may use either UAT or 1090ES equipment. (Refer to 14 CFR §§ 91.225 and 91.227.) While the regulations do not require it, operators equipped with ADS−B In will realize additional benefits from ADS−B broadcast Surveillance Systems 6/17/21 AIM services: Traffic Information Service – Broadcast (TIS−B) (Paragraph 4−5−8) and Flight Information Service − Broadcast (FIS−B) (Paragraph 4−5−9). FIG 4−5−7 ADS−B, TIS−B, and FIS−B: Broadcast Services Architecture b. ADS−B Certification and Performance Requirements. ADS−B equipment may be certified as a surveillance source for air traffic separation services using ADS−B Out. ADS−B equipment may also be certified for use with ADS−B In advisory services that enable appropriately equipped aircraft to display traffic and flight information. Refer to the aircraft’s flight manual supplement or Pilot Operating Handbook for the capabilities of a specific aircraft installation. Surveillance Systems c. ADS−B Capabilities and Procedures. 1. ADS−B enables improved surveillance services, both air−to−air and air−to−ground, especially in areas where radar is ineffective due to terrain or where it is impractical or cost prohibitive. Initial NAS applications of air−to−air ADS−B are for “advisory” use only, enhancing a pilot’s visual acquisition of other nearby equipped aircraft either when airborne or on the airport surface. Additionally, ADS−B will enable ATC and fleet operators to monitor aircraft throughout the available ground station coverage area. 4−5−15 AIM 6/17/21 FIG 4−5−8 En Route − ADS−B/ADS−R/TIS−B/FIS−B Service Ceilings/Floors FIG 4−5−9 Terminal − ADS−B/ADS−R/TIS−B/FIS−B Service Ceilings/Floors 4−5−16 Surveillance Systems 6/17/21 2. One of the data elements transmitted by ADS−B is the aircraft’s Flight Identification (FLT ID). The FLT ID is comprised of a maximum of seven alphanumeric characters and must correspond to the aircraft identification filed in the flight plan. For airline and commuter aircraft, the FLT ID is usually the company name and flight number (for example, AAL3432), and is typically entered into the avionics by the flight crew during preflight. For general aviation (GA), if aircraft avionics allow dynamic modification of the FLT ID, the pilot can enter it prior to flight. However, some ADS−B avionics require the FLT ID to be set to the aircraft registration number (for example, N1234Q) by the installer and cannot be changed by the pilot from the cockpit. In both cases, the FLT ID must correspond to the aircraft identification filed in its flight plan. ATC automation systems use the transmitted ADS−B FLT ID to uniquely identify each aircraft within a given airspace, and to correlate it to its filed flight plan for the purpose of providing surveillance and separation services. If the FLT ID and the filed aircraft identification are not identical, a Call Sign Mis−Match (CSMM) is generated and ATC automation systems may not associate the aircraft with its filed flight plan. In this case, air traffic services may be delayed or unavailable until the CSMM is corrected. Consequently, it is imperative that flight crews and GA pilots ensure the FLT ID entry correctly matches the aircraft identification filed in their flight plan. 3. Each ADS−B aircraft is assigned a unique ICAO address (also known as a 24−bit address) that is broadcast by the ADS−B transmitter. This ICAO address is programmed at installation. Should multiple aircraft broadcast the same ICAO address while transiting the same ADS−B Only Service Volume, the ADS−B network may be unable to track the targets correctly. If radar reinforcement is available, tracking will continue. If radar is unavailable, the controller may lose target tracking entirely on one or both targets. Consequently, it is imperative that the ICAO address entry is correct. 4. Aircraft that are equipped with ADS−B avionics on the UAT datalink have a feature that allows them to broadcast an anonymous 24−bit ICAO Surveillance Systems AIM address. In this mode, the UAT system creates a randomized address that does not match the actual ICAO address assigned to the aircraft. The UAT anonymous 24−bit address feature may only be used when the operator has not filed an IFR flight plan and is not requesting ATC services. In the anonymity mode, the aircraft’s beacon code must be set to 1200 and, depending on the manufacturer’s implementation, the aircraft FLT ID might not be transmitted. Pilots should be aware that while in UAT anonymity mode, they will not be eligible to receive ATC separation and flight following services, and may not benefit from enhanced ADS−B search and rescue capabilities. 5. ADS−B systems integrated with the transponder will automatically set the applicable emergency status when 7500, 7600, or 7700 are entered into the transponder. ADS−B systems not integrated with the transponder, or systems with optional emergency codes, will require that the appropriate emergency code is entered through a pilot interface. ADS−B is intended for inflight and airport surface use. Unless otherwise directed by ATC, transponder/ADS−B systems should be turned “on” and remain “on” whenever operating in the air or on the airport surface movement area. d. ATC Surveillance Services using ADS−B − Procedures and Recommended Phraseology Radar procedures, with the exceptions found in this paragraph, are identical to those procedures prescribed for radar in AIM Chapter 4 and Chapter 5. 1. Preflight: If ATC services are anticipated when either a VFR or IFR flight plan is filed, the aircraft identification (as entered in the flight plan) must be entered as the FLT ID in the ADS−B avionics. 2. Inflight: When requesting surveillance services while airborne, pilots must disable the anonymous feature, if so equipped, prior to contacting ATC. Pilots must also ensure that their transmitted ADS−B FLT ID matches the aircraft identification as entered in their flight plan. 4−5−17 AIM 6/17/21 3. Aircraft with an Inoperative/Malfunctioning ADS−B Transmitter: the FAA will normally not take enforcement action for non−equipage in these circumstances. (a) ATC will inform the flight crew when the aircraft’s ADS−B transmitter appears to be inoperative or malfunctioning: NOTE− Pilots operating without ADS−B equipment must not request route or altitude changes that will result in an incursion into ADS−B airspace except for safety of flight; for example, weather avoidance. Unequipped aircraft that have not received a pre−flight deviation authorization will only be considered in compliance with regulation if the amendment to flight is initiated by ATC. PHRASEOLOGY− YOUR ADS−B TRANSMITTER APPEARS TO BE INOPERATIVE/MALFUNCTIONING. STOP ADS−B TRANSMISSIONS. (b) ATC will inform the flight crew if it becomes necessary to turn off the aircraft’s ADS−B transmitter. PHRASEOLOGY− STOP ADS−B TRANSMISSIONS. (c) Other malfunctions and considerations: Loss of automatic altitude reporting capabilities (encoder failure) will result in loss of ATC altitude advisory services. 4. Procedures for Accommodation of Non− ADS−B Equipped Aircraft: (a) Pilots of aircraft not equipped with ADS−B may only operate outside airspace designated as ADS−B airspace in 14 CFR §91.225. Pilots of unequipped aircraft wishing to fly any portion of a flight in ADS−B airspace may seek a deviation from the regulation to conduct operations without the required equipment. Direction for obtaining this deviation are available in Advisory Circular 90−114. (b) While air traffic controllers can identify which aircraft are ADS−B equipped and which are not, there is no indication if a non−equipped pilot has obtained a preflight authorization to enter ADS−B airspace. Situations may occur when the pilot of a non−equipped aircraft, without an authorization to operate in ADS−B airspace receives an ATC−initiated in−flight clearance to fly a heading, route, or altitude that would penetrate ADS−B airspace. Such clearances may be for traffic, weather, or simply to shorten the aircraft’s route of flight. When this occurs, the pilot should acknowledge and execute the clearance, but must advise the controller that they are not ADS−B equipped and have not received prior authorization to operate in ADS−B airspace. The controller, at their discretion, will either acknowledge and proceed with the new clearance, or modify the clearance to avoid ADS−B airspace. In either case, 4−5−18 EXAMPLE− 1. ATC: “November Two Three Quebec, turn fifteen degrees left, proceed direct Bradford when able, rest of route unchanged.” Aircraft: “November Two Three Quebec, turning fifteen degrees left, direct Bradford when able, rest of route unchanged. Be advised, we are negative ADS−B equipment and have not received authorization to operate in ADS−B airspace.” ATC: “November Two Three Quebec, roger” or “November Two Three Quebec, roger, turn twenty degrees right, rejoin Victor Ten, rest of route unchanged.” 2. ATC: “November Four Alpha Tango, climb and maintain one zero thousand for traffic.” Aircraft: “November Four Alpha Tango, leaving eight thousand for one zero thousand. Be advised, we are negative ADS−B equipment and have not received authorization to operate in ADS−B airspace.” ATC: “November Four Alpha Tango, roger” or “November Four Alpha Tango, roger, cancel climb clearance, maintain eight thousand.” REFERENCE− Federal Register Notice, Volume 84, Number 62, dated April 1, 2019 e. ADS−B Limitations. The ADS−B cockpit display of traffic is NOT intended to be used as a collision avoidance system and does not relieve the pilot’s responsibility to “see and avoid” other aircraft. (See Paragraph 5−5−8, See and Avoid). ADS−B must not be used for avoidance maneuvers during IMC or other times when there is no visual contact with the intruder aircraft. ADS−B is intended only to assist in visual acquisition of other aircraft. No avoidance maneuvers are provided or authorized, as a direct result of an ADS−B target being displayed in the cockpit. f. Reports of ADS−B Malfunctions. Users of ADS−B can provide valuable assistance in the correction of malfunctions by reporting instances of undesirable system performance. Since ADS−B Surveillance Systems 6/17/21 performance is monitored by maintenance personnel rather than ATC, report malfunctions to the nearest Flight Service Station (FSS) facility by radio or telephone, or by sending an email to the ADS−B help desk at adsb@faa.gov. Reports should include: 1. Condition observed; 2. Date and time of observation; 3. Altitude and location of observation; 4. Type and call sign of the aircraft; and 5. Type and software version of avionics system. 4−5−8. Traffic Information Service− Broadcast (TIS−B) a. Introduction TIS−B is the broadcast of ATC derived traffic information to ADS−B equipped (1090ES or UAT) aircraft from ground radio stations. The source of this traffic information is derived from ground−based air traffic surveillance sensors. TIS−B service will be available throughout the NAS where there are both adequate surveillance coverage from ground sensors and adequate broadcast coverage from ADS−B ground radio stations. The quality level of traffic information provided by TIS−B is dependent upon the number and type of ground sensors available as TIS−B sources and the timeliness of the reported data. (See FIG 4−5−8 and FIG 4−5−9.) b. TIS−B Requirements. In order to receive TIS−B service, the following conditions must exist: 1. Aircraft must be equipped with an ADS−B transmitter/receiver or transceiver, and a cockpit display of traffic information (CDTI). 2. Aircraft must fly within the coverage volume of a compatible ground radio station that is configured for TIS−B uplinks. (Not all ground radio stations provide TIS−B due to a lack of radar coverage or because a radar feed is not available). 3. Aircraft must be within the coverage of and detected by at least one ATC radar serving the ground radio station in use. c. TIS−B Capabilities. Surveillance Systems AIM 1. TIS−B is intended to provide ADS−B equipped aircraft with a more complete traffic picture in situations where not all nearby aircraft are equipped with ADS−B Out. This advisory−only application is intended to enhance a pilot’s visual acquisition of other traffic. 2. Only transponder−equipped targets (i.e., Mode A/C or Mode S transponders) are transmitted through the ATC ground system architecture. Current radar siting may result in limited radar surveillance coverage at lower altitudes near some airports, with subsequently limited TIS−B service volume coverage. If there is no radar coverage in a given area, then there will be no TIS−B coverage in that area. d. TIS−B Limitations. 1. TIS−B is NOT intended to be used as a collision avoidance system and does not relieve the pilot’s responsibility to “see and avoid” other aircraft, in accordance with 14CFR §91.113b. TIS−B must not be used for avoidance maneuvers during times when there is no visual contact with the intruder aircraft. TIS−B is intended only to assist in the visual acquisition of other aircraft. NOTE− No aircraft avoidance maneuvers are authorized as a direct result of a TIS−B target being displayed in the cockpit. 2. While TIS−B is a useful aid to visual traffic avoidance, its inherent system limitations must be understood to ensure proper use. (a) A pilot may receive an intermittent TIS−B target of themselves, typically when maneuvering (e.g., climbing turns) due to the radar not tracking the aircraft as quickly as ADS−B. (b) The ADS−B−to−radar association process within the ground system may at times have difficulty correlating an ADS−B report with corresponding radar returns from the same aircraft. When this happens the pilot may see duplicate traffic symbols (i.e., “TIS−B shadows”) on the cockpit display. (c) Updates of TIS−B traffic reports will occur less often than ADS−B traffic updates. TIS−B position updates will occur approximately once every 3−13 seconds depending on the type of radar system in use within the coverage area. In comparison, the update rate for ADS−B is nominally once per second. 4−5−19 7110.65R CHG 2 AIM AIM (d) The TIS−B system only uplinks data pertaining to transponder−equipped aircraft. Aircraft without a transponder will not be displayed as TIS−B traffic. (e) There is no indication provided when any aircraft is operating inside or outside the TIS−B service volume, therefore it is difficult to know if one is receiving uplinked TIS−B traffic information. 3. Pilots and operators are reminded that the airborne equipment that displays TIS−B targets is for pilot situational awareness only and is not approved as a collision avoidance tool. Unless there is an imminent emergency requiring immediate action, any deviation from an air traffic control clearance in response to perceived converging traffic appearing on a TIS−B display must be approved by the controlling ATC facility before commencing the maneuver, except as permitted under certain conditions in 14CFR §91.123. Uncoordinated deviations may place an aircraft in close proximity to other aircraft under ATC control not seen on the airborne equipment and may result in a pilot deviation or other incident. e. Reports of TIS−B Malfunctions. Users of TIS−B can provide valuable assistance in the correction of malfunctions by reporting instances of undesirable system performance. Since TIS−B performance is monitored by maintenance personnel rather than ATC, report malfunctions to the nearest Flight Service Station (FSS) facility by radio or telephone, or by sending an email to the ADS−B help desk at adsb@faa.gov. Reports should include: 1. Condition observed; 2. Date and time of observation; 3. Altitude and location of observation; 4. Type and call sign of the aircraft; and 3/15/07 12/2/21 6/17/21 FIS−B is a ground broadcast service provided through the ADS−B Services network over the 978 MHz UAT data link. The FAA FIS−B system provides pilots and flight crews of properly equipped aircraft with a cockpit display of certain aviation weather and aeronautical information. FIS−B reception is line−of−sight within the service volume of the ground infrastructure. (See FIG 4−5−8 and FIG 4−5−9.) b. Weather Products. FIS-B does not replace a preflight weather briefing from a source listed in paragraph 7−1−2, FAA Weather Services, or inflight updates from an FSS or ATC. FIS-B information may be used by the pilot for the safe conduct of flight and aircraft movement; however, the information should not be the only source of weather or aeronautical information. A pilot should be particularly alert and understand the limitations and quality assurance issues associated with individual products. This includes graphical representation of next generation weather radar (NEXRAD) imagery and Notices to Air Missions (NOTAMs)/temporary flight restrictions (TFRs). REFERENCE− AIM, Para 7−1−9, Flight Information Services (FIS). Advisory Circular (AC) 00−63, “Use of Cockpit Displays of Digital Weather and Aeronautical Information.” c. Reports of FIS−B Malfunctions. Users of FIS−B can provide valuable assistance in the correction of malfunctions by reporting instances of undesirable system performance. Since FIS−B performance is monitored by maintenance personnel rather than ATC, report malfunctions to the nearest Flight Service Station (FSS) facility by radio or telephone, or by sending an email to the ADS−B help desk at adsb@faa.gov. Reports should include: 1. Condition observed; 5. Type and software version of avionics system. 2. Date and time of observation; 4−5−9. Flight Information Service− Broadcast (FIS−B) 4. Type and call sign of the aircraft; and a. Introduction. 4−5−20 3. Altitude and location of observation; 5. Type and software version of avionics system. Surveillance Systems 6/17/21 AIM TBL 4−5−3 FIS−B Over UAT Product Update and Transmission Intervals Product Update Interval1 Transmission Interval (95%)2 5 minutes Basic Product Yes AIRMET As Available AWW/WW As Available, then at 15 minute 5 minutes intervals for 1 hour No Ceiling As Available No Convective SIGMET As Available, then at 15 minute 5 minutes intervals for 1 hour Yes D−ATIS Echo Top As Available 1 minute 5 minutes 5 minutes 1 minute (where available), As 5 minutes Available otherwise No No METAR/SPECI 10 minutes 15 minutes 2.5 minutes 10 minutes 10 minutes 10 minutes Yes MRMS NEXRAD (CONUS) MRMS NEXRAD (Regional) NOTAMs−D/FDC NOTAMs−TFR PIREP 2 minutes 2 minutes As Available As Available As Available Yes Yes Yes Yes Yes SIGMET As Available, then at 15 minute 5 minutes intervals for 1 hour Yes SUA Status TAF/AMEND Temperature Aloft TWIP Winds aloft Lightning strikes 3 Turbulence 3 As Available 6 Hours (±15 minutes) 12 Hours (±15 minutes) As Available 12 Hours (±15 minutes) 5 minutes 1 minute 10 minutes 10 minutes 10 minutes 1 minute Yes Yes Yes No 10 minutes 5 minutes 15 minutes Yes Yes Yes Icing, Forecast Potential (FIP) 3 Cloud tops 3 60 minutes 30 minutes 15 minutes 15 minutes Yes Yes 1 Minute AWOS 3 Graphical−AIRMET 3 Center Weather Advisory (CWA) 3 Temporary Restricted Areas (TRA) 1 minute As Available As Available 10 minutes 5 minutes 10 minutes No Yes Yes As Available 10 minutes Yes Temporary Military Operations Areas As Available (TMOA) 10 minutes Yes 1 The Update Interval is the rate at which the product data is available from the source. The Transmission Interval is the amount of time within which a new or updated product transmission must be completed (95%) and the rate or repetition interval at which the product is rebroadcast (95%). 3 The transmission and update intervals for the expanded set of basic meteorological products may be adjusted based on FAA and vendor agreement on the final product formats and performance requirements. 2 Surveillance Systems 4−5−21 AIM NOTE− 1. Details concerning the content, format, and symbols of the various data link products provided should be obtained from the specific avionics manufacturer. 2. NOTAM−D and NOTAM−FDC products broadcast via FIS−B are limited to those issued or effective within the past 30 days. 4−5−10. Automatic Dependent Surveillance−Rebroadcast (ADS−R) a. Introduction. ADS−R is a datalink translation function of the ADS−B ground system required to accommodate the two separate operating frequencies (978 MHz and 1090 ES). The ADS−B system receives the ADS−B messages transmitted on one frequency and ADS−R translates and reformats the information for rebroadcast and use on the other frequency. This allows ADS−B In equipped aircraft to see nearby ADS−B Out traffic regardless of the operating link of the other aircraft. Aircraft operating on the same 4−5−22 6/17/21 ADS−B frequency exchange information directly and do not require the ADS−R translation function. (See FIG 4−5−8 and FIG 4−5−9.) b. Reports of ADS−R Malfunctions. Users of ADS–R can provide valuable assistance in the correction of malfunctions by reporting instances of undesirable system performance. Since ADS–R performance is monitored by maintenance personnel rather than ATC, report malfunctions to the nearest Flight Service Station (FSS) facility by radio or telephone, or by sending an email to the ADS−B help desk at adsb@faa.gov. Reports should include: 1. Condition observed; 2. Date and time of observation; 3. Altitude and location of observation; 4. Type and call sign of the aircraft and; 5. Type and software version of avionics system. Surveillance Systems 6/17/21 AIM Section 6. Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4−6−1. Applicability and RVSM Mandate (Date/Time and Area) a. Applicability. The policies, guidance and direction in this section apply to RVSM operations in the airspace over the lower 48 states, Alaska, Atlantic and Gulf of Mexico High Offshore Airspace and airspace in the San Juan FIR where VHF or UHF voice direct controller−pilot communication (DCPC) is normally available. Policies, guidance and direction for RVSM operations in oceanic airspace where VHF or UHF voice DCPC is not available and the airspace of other countries can be found in the Aeronautical Information Publication (AIP), Part II− En Route, ENR 1. General Rules and Procedures, and ENR 7.Oceanic Operations. d. Benefits. RVSM enhances ATC flexibility, mitigates conflict points, enhances sector throughput, reduces controller workload and enables crossing traffic. Operators gain fuel savings and operating efficiency benefits by flying at more fuel efficient flight levels and on more user preferred routings. 4−6−2. Flight Level Orientation Scheme Altitude assignments for direction of flight follow a scheme of odd altitude assignment for magnetic courses 000−179 degrees and even altitudes for magnetic courses 180−359 degrees for flights up to and including FL 410, as indicated in FIG 4−6−1. FIG 4−6−1 Flight Level Orientation Scheme b. Requirement. The FAA implemented RVSM between flight level (FL) 290−410 (inclusive) in the following airspace: the airspace of the lower 48 states of the United States, Alaska, Atlantic and Gulf of Mexico High Offshore Airspace and the San Juan FIR. RVSM has been implemented worldwide and may be applied in all ICAO Flight Information Regions (FIR). c. RVSM Authorization. In accordance with 14 CFR Section 91.180, with only limited exceptions, prior to operating in RVSM airspace, operators must comply with the standards of Part 91, Appendix G, and be authorized by the Administrator. If either the operator or the operator’s aircraft have not met the applicable RVSM standards, the aircraft will be referred to as a “non−RVSM” aircraft. Paragraph 4−6−10 discusses ATC policies for accommodation of non−RVSM aircraft flown by the Department of Defense, Air Ambulance (MEDEVAC) operators, foreign State governments and aircraft flown for certification and development. Paragraph 4−6−11, Non−RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off, contains policies for non−RVSM aircraft climbing and descending through RVSM airspace to/from flight levels above RVSM airspace. NOTE− Odd Flight Levels: Magnetic Course 000−179 Degrees Even Flight Levels: Magnetic Course 180−359 Degrees. 4−6−3. Aircraft and Operator Approval Policy/Procedures, RVSM Monitoring and Databases for Aircraft and Operator Approval a. RVSM Authority. 14 CFR Section 91.180 applies to RVSM operations within the U.S. 14 CFR Section 91.706 applies to RVSM operations outside Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4−6−1 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 the U.S. Both sections require that the operator be authorized prior to operating in RVSM airspace. For Domestic RVSM operations, an operator may choose to operate under the provisions of Part 91, Appendix G, Section 9; or if intending to operate outside U.S. airspace, hold a specific approval (OpSpec/MSpec/LOA) under the provisions of Section 3 of Part 91, Appendix G. b. Sources of Information. Advisory Circular (AC) 91−85, Authorization of Aircraft and Operators for Flight in Reduced Vertical Separation Minimum (RVSM) Airspace, and the FAA RVSM website. 4−6−4. Flight Planning into RVSM Airspace a. Operators that do not file the correct aircraft equipment suffix on the FAA or ICAO Flight Plan may be denied clearance into RVSM airspace. Policies for the FAA Flight Plan are detailed in subparagraph c below. Policies for the ICAO Flight Plan are detailed in subparagraph d. b. The operator will annotate the equipment block of the FAA or ICAO Flight Plan with an aircraft equipment suffix indicating RVSM capability only after determining that both the operator is authorized and its aircraft are RVSM−compliant. c. TCAS Equipage. TCAS equipage requirements are contained in 14 CFR Sections 121.356, 125.224, 129.18 and 135.189. Part 91, Appendix G, does not contain TCAS equipage requirements specific to RVSM, however, Appendix G does require that aircraft equipped with TCAS II and flown in RVSM airspace be modified to incorporate TCAS II Version 7.0 or a later version. 1. An operator may operate in RVSM airspace under the provisions of Part 91, Appendix G, Section 9, without specific authorization and should file “/w” in accordance with paragraph d. d. Aircraft Monitoring. Operators are required to participate in the RVSM altitude−keeping performance monitoring program that is appropriate for the type of operation being conducted. The monitoring programs are described in AC 91−85. Monitoring is a quality control program that enables the FAA and other civil aviation authorities to assess the in−service altitude−keeping performance of aircraft and operators. 3. An operator should not file “/w” when intending to operate in RVSM airspace outside of the U.S., if they do not hold a valid OpSpec/MSpec/ LOA. e. Purpose of RVSM Approvals Databases. All RVSM designated airspace is monitored airspace. ATC does not use RVSM approvals databases to determine whether or not a clearance can be issued into RVSM airspace. RVSM program managers do regularly review the operators and aircraft that operate in RVSM airspace to identify and investigate those aircraft and operators flying in RVSM airspace, but not listed on the RVSM approvals databases. 1. The operator will annotate the equipment block of the FAA Flight Plan with the appropriate aircraft equipment suffix from Appendix 4, TBL 4−2 and/or TBL 4−3. f. Registration of U.S. Operators. When U.S. operators and aircraft are granted specific RVSM authority, the Separation Standards Group at the FAA Technical Center obtains PTRS operator and aircraft information to update the FAA maintained U.S. Operator/Aircraft RVSM Approvals database. Basic database operator and aircraft information can be viewed on the RVSM Documentation web page in the “RVSM Approvals” section. 4−6−2 2. An operator must get an OpSpec/MSpec/ LOA when intending to operate RVSM outside U.S. airspace. Once issued, that operator can file “/w” in accordance with paragraph d. c. General Policies for FAA Flight Plan Equipment Suffix. Appendix 4, TBL 4−2, allows operators to indicate that the aircraft has both RVSM and Advanced Area Navigation (RNAV) capabilities or has only RVSM capability. 2. Operators can only file one equipment suffix in block 3 of the FAA Flight Plan. Only this equipment suffix is displayed directly to the controller. 3. Aircraft with RNAV Capability. For flight in RVSM airspace, aircraft with RNAV capability, but not Advanced RNAV capability, will file “/W”. Filing “/W” will not preclude such aircraft from filing and flying direct routes in en route airspace. d. Policy for ICAO Flight Plan Equipment Suffixes. 1. Operators/aircraft that are RVSM−compliant and that file ICAO flight plans will file “/W” in Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 12/2/21 6/17/21 block 10 (Equipment) to indicate RVSM authorization and will also file the appropriate ICAO Flight Plan suffixes to indicate navigation and communication capabilities. 2. Operators/aircraft that file ICAO flight plans that include flight in Domestic U.S. RVSM airspace must file “/W” in block 10 to indicate RVSM authorization. e. Importance of Flight Plan Equipment Suffixes. Military users, and civilians who file stereo route flight plans, must file the appropriate equipment suffix in the equipment block of the FAA Form 7233−1, Flight Plan, or DD Form 175, Military Flight Plan, or FAA Form 7233−4, International Flight Plan, or DD Form 1801, DOD International Flight Plan. All other users must file the appropriate equipment suffix in the equipment block of FAA Form 7233−4, International Flight Plan. The equipment suffix informs ATC: 1. Whether or not the operator and aircraft are authorized to fly in RVSM airspace. 2. The navigation and/or transponder capability of the aircraft (e.g., advanced RNAV, transponder with Mode C). f. Significant ATC uses of the flight plan equipment suffix information are: 1. To issue or deny clearance into RVSM airspace. 2. To apply a 2,000 foot vertical separation minimum in RVSM airspace to aircraft that are not authorized for RVSM, but are in one of the limited categories that the FAA has agreed to accommodate. (See paragraphs 4−6−10, Procedures for Accommodation of Non−RVSM Aircraft, and 4−6−11, Non−RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off, for policy on limited operation of unapproved aircraft in RVSM airspace). AIM processes correctly for Non-RVSM aircraft, the “W” in Field 10 must be removed. Entry of information in the NOTES or REMARKS section (Field 18) will not affect the determination of RVSM capability and must not be used to indicate a flight is Non-RVSM. 4−6−5. Pilot RVSM Operating Practices and Procedures a. RVSM Mandate. If either the operator is not authorized for RVSM operations or the aircraft is not RVSM−compliant, the pilot will neither request nor accept a clearance into RVSM airspace unless: 1. The flight is conducted by a non−RVSM DOD, MEDEVAC, certification/development or foreign State (government) aircraft in accordance with paragraph 4−6−10, Procedures for Accommodation of Non−RVSM Aircraft. 2. The pilot intends to climb to or descend from FL 430 or above in accordance with paragraph 4−6−11, Non−RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off. 3. An emergency situation exists. b. Basic RVSM Operating Practices and Procedures. AC 91−85 contains pilot practices and procedures for RVSM. Operators must incorporate applicable practices and procedures, as supplemented by the applicable paragraphs of this section, into operator training or pilot knowledge programs and operator documents containing RVSM operational policies. c. AC 91−85 contains practices and procedures for flight planning, preflight procedures at the aircraft, procedures prior to RVSM airspace entry, inflight (en route) procedures, contingency procedures and post flight. d. The following paragraphs either clarify or supplement AC 91−85 practices and procedures. 3. To determine if the aircraft has “Advanced RNAV” capabilities and can be cleared to fly procedures for which that capability is required. 4−6−6. Guidance on Severe Turbulence and Mountain Wave Activity (MWA) g. Improperly changing an aircraft equipment suffix and/or adding “NON-RVSM” in the NOTES or REMARKS section (Field 18) while not removing the “W” from Field 10, will not provide air traffic control with the proper visual indicator necessary to detect Non-RVSM aircraft. To ensure information 1. The information and practices in this paragraph are provided to emphasize to pilots and controllers the importance of taking appropriate action in RVSM airspace when aircraft experience severe turbulence and/or MWA that is of sufficient magnitude to significantly affect altitude−keeping. a. Introduction/Explanation Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4−6−3 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 2. Severe Turbulence. Severe turbulence causes large, abrupt changes in altitude and/or attitude usually accompanied by large variations in indicated airspeed. Aircraft may be momentarily out of control. Encounters with severe turbulence must be remedied immediately in any phase of flight. Severe turbulence may be associated with MWA. 3. Mountain Wave Activity (MWA) (a) Significant MWA occurs both below and above the floor of RVSM airspace, FL 290. MWA often occurs in western states in the vicinity of mountain ranges. It may occur when strong winds blow perpendicular to mountain ranges resulting in up and down or wave motions in the atmosphere. Wave action can produce altitude excursions and airspeed fluctuations accompanied by only light turbulence. With sufficient amplitude, however, wave action can induce altitude and airspeed fluctuations accompanied by severe turbulence. MWA is difficult to forecast and can be highly localized and short lived. (b) Wave activity is not necessarily limited to the vicinity of mountain ranges. Pilots experiencing wave activity anywhere that significantly affects altitude−keeping can follow the guidance provided below. (c) Inflight MWA Indicators (Including Turbulence). Indicators that the aircraft is being subjected to MWA are: (1) Altitude excursions and/or airspeed fluctuations with or without associated turbulence. (2) Pitch and trim changes required to maintain altitude with accompanying airspeed fluctuations. (3) Light to severe turbulence depending on the magnitude of the MWA. 4. Priority for Controller Application of Merging Target Procedures (a) Explanation of Merging Target Procedures. As described in subparagraph c3 below, ATC will use “merging target procedures” to mitigate the effects of both severe turbulence and MWA. The procedures in subparagraph c3 have been adapted from existing procedures published in FAA Order JO 7110.65, Air Traffic Control, paragraph 5−1−4, Merging Target Procedures. paragraph 5−1−4 calls for en route controllers to advise pilots of potential 4−6−4 traffic that they perceive may fly directly above or below his/her aircraft at minimum vertical separation. In response, pilots are given the option of requesting a radar vector to ensure their radar target will not merge or overlap with the traffic’s radar target. (b) The provision of “merging target procedures” to mitigate the effects of severe turbulence and/or MWA is not optional for the controller, but rather is a priority responsibility. Pilot requests for vectors for traffic avoidance when encountering MWA or pilot reports of “Unable RVSM due turbulence or MWA” are considered first priority aircraft separation and sequencing responsibilities. (FAA Order JO 7110.65, paragraph 2−1−2, Duty Priority, states that the controller’s first priority is to separate aircraft and issue safety alerts). (c) Explanation of the term “traffic permitting.” The contingency actions for MWA and severe turbulence detailed in paragraph 4−6−9, Contingency Actions: Weather Encounters and Aircraft System Failures that Occur After Entry into RVSM Airspace, state that the controller will “vector aircraft to avoid merging targets with traffic at adjacent flight levels, traffic permitting.” The term “traffic permitting” is not intended to imply that merging target procedures are not a priority duty. The term is intended to recognize that, as stated in FAA Order JO 7110.65, paragraph 2−1−2, Duty Priority, there are circumstances when the controller is required to perform more than one action and must “exercise their best judgment based on the facts and circumstances known to them” to prioritize their actions. Further direction given is: “That action which is most critical from a safety standpoint is performed first.” 5. TCAS Sensitivity. For both MWA and severe turbulence encounters in RVSM airspace, an additional concern is the sensitivity of collision avoidance systems when one or both aircraft operating in close proximity receive TCAS advisories in response to disruptions in altitude hold capability. b. Pre−flight tools. Sources of observed and forecast information that can help the pilot ascertain the possibility of MWA or severe turbulence are: Forecast Winds and Temperatures Aloft (FD), Area Forecast (FA), Graphical Turbulence Guidance (GTG), SIGMETs and PIREPs. Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 12/2/21 6/17/21 c. Pilot Actions When Encountering Weather (e.g., Severe Turbulence or MWA) 1. Weather Encounters Inducing Altitude Deviations of Approximately 200 feet. When the pilot experiences weather induced altitude deviations of approximately 200 feet, the pilot will contact ATC and state “Unable RVSM Due (state reason)” (e.g., turbulence, mountain wave). See contingency actions in paragraph 4−6−9. 2. Severe Turbulence (including that associated with MWA). When pilots encounter severe turbulence, they should contact ATC and report the situation. Until the pilot reports clear of severe turbulence, the controller will apply merging target vectors to one or both passing aircraft to prevent their targets from merging: EXAMPLE− “Yankee 123, FL 310, unable RVSM due severe turbulence.” “Yankee 123, fly heading 290; traffic twelve o’clock, 10 miles, opposite direction; eastbound MD−80 at FL 320” (or the controller may issue a vector to the MD−80 traffic to avoid Yankee 123). 3. MWA. When pilots encounter MWA, they should contact ATC and report the magnitude and location of the wave activity. When a controller makes a merging targets traffic call, the pilot may request a vector to avoid flying directly over or under the traffic. In situations where the pilot is experiencing altitude deviations of 200 feet or greater, the pilot will request a vector to avoid traffic. Until the pilot reports clear of MWA, the controller will apply merging target vectors to one or both passing aircraft to prevent their targets from merging: EXAMPLE− “Yankee 123, FL 310, unable RVSM due mountain wave.” “Yankee 123, fly heading 290; traffic twelve o’clock, 10 miles, opposite direction; eastbound MD−80 at FL 320” (or the controller may issue a vector to the MD−80 traffic to avoid Yankee 123). 4. FL Change or Re−route. To leave airspace where MWA or severe turbulence is being encountered, the pilot may request a FL change and/or re−route, if necessary. 4−6−7. Guidance on Wake Turbulence a. Pilots should be aware of the potential for wake turbulence encounters in RVSM airspace. Experience AIM gained since 1997 has shown that such encounters in RVSM airspace are generally moderate or less in magnitude. b. Prior to DRVSM implementation, the FAA established provisions for pilots to report wake turbulence events in RVSM airspace using the NASA Aviation Safety Reporting System (ASRS). A “Safety Reporting” section established on the FAA RVSM Documentation web page provides contacts, forms, and reporting procedures. c. To date, wake turbulence has not been reported as a significant factor in DRVSM operations. European authorities also found that reports of wake turbulence encounters did not increase significantly after RVSM implementation (eight versus seven reports in a ten−month period). In addition, they found that reported wake turbulence was generally similar to moderate clear air turbulence. d. Pilot Action to Mitigate Wake Turbulence Encounters 1. Pilots should be alert for wake turbulence when operating: (a) In the vicinity of aircraft climbing or descending through their altitude. (b) Approximately 10−30 miles after passing 1,000 feet below opposite−direction traffic. (c) Approximately 10−30 miles behind and 1,000 feet below same−direction traffic. 2. Pilots encountering or anticipating wake turbulence in DRVSM airspace have the option of requesting a vector, FL change, or if capable, a lateral offset. NOTE− 1. Offsets of approximately a wing span upwind generally can move the aircraft out of the immediate vicinity of another aircraft’s wake vortex. 2. In domestic U.S. airspace, pilots must request clearance to fly a lateral offset. Strategic lateral offsets flown in oceanic airspace do not apply. 4−6−8. Pilot/Controller Phraseology TBL 4−6−1 shows standard phraseology that pilots and controllers will use to communicate in DRVSM operations. Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4−6−5 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 TBL 4−6−1 Pilot/Controller Phraseology Message For a controller to ascertain the RVSM approval status of an aircraft: Pilot indication that flight is RVSM approved Pilot report of lack of RVSM approval (non−RVSM status). Pilot will report non−RVSM status, as follows: a. On the initial call on any frequency in the RVSM airspace and . . .. b. In all requests for flight level changes pertaining to flight levels within the RVSM airspace and . . .. c. In all read backs to flight level clearances pertaining to flight levels within the RVSM airspace and . . .. d. In read back of flight level clearances involving climb and descent through RVSM airspace (FL 290 − 410). Pilot report of one of the following after entry into RVSM airspace: all primary altimeters, automatic altitude control systems or altitude alerters have failed. (See paragraph 4−6−9, Contingency Actions: Weather Encounters and Aircraft System Failures that Occur After Entry into RVSM Airspace.) Phraseology (call sign) confirm RVSM approved Affirm RVSM Negative RVSM, (supplementary information, e.g., “Certification flight”). Unable RVSM Due Equipment NOTE− This phrase is to be used to convey both the initial indication of RVSM aircraft system failure and on initial contact on all frequencies in RVSM airspace until the problem ceases to exist or the aircraft has exited RVSM airspace. ATC denial of clearance into RVSM airspace *Pilot reporting inability to maintain cleared flight level due to weather encounter. (See Paragraph 4−6−9, Contingency Actions: Weather Encounters and Aircraft System Failures that Occur After Entry into RVSM Airspace.). Unable issue clearance into RVSM airspace, maintain FL *Unable RVSM due (state reason) (e.g., turbulence, mountain wave) ATC requesting pilot to confirm that an aircraft has regained RVSM−approved status or a pilot is ready to resume RVSM Pilot ready to resume RVSM after aircraft system or weather contingency Confirm able to resume RVSM 4−6−9. Contingency Actions: Weather Encounters and Aircraft System Failures that Occur After Entry into RVSM Airspace TBL 4−6−2 provides pilot guidance on actions to take under certain conditions of aircraft system 4−6−6 Ready to resume RVSM failure that occur after entry into RVSM airspace and weather encounters. It also describes the expected ATC controller actions in these situations. It is recognized that the pilot and controller will use judgment to determine the action most appropriate to any given situation. Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 12/2/21 6/17/21 AIM TBL 4−6−2 Contingency Actions: Weather Encounters and Aircraft System Failures that Occur After Entry into RVSM Airspace Initial Pilot Actions in Contingency Situations Initial pilot actions when unable to maintain flight level (FL) or unsure of aircraft altitude−keeping capability: Notify ATC and request assistance as detailed below. Maintain cleared flight level, to the extent possible, while evaluating the situation. Watch for conflicting traffic both visually and by reference to TCAS, if equipped. Alert nearby aircraft by illuminating exterior lights (commensurate with aircraft limitations). Severe Turbulence and/or Mountain Wave Activity (MWA) Induced Altitude Deviations of Approximately 200 feet Pilot will: Controller will: When experiencing severe turbulence and/or Vector aircraft to avoid merging target with MWA induced altitude deviations of traffic at adjacent flight levels, traffic permitting approximately 200 feet or greater, pilot will contact ATC and state “Unable RVSM Due (state Advise pilot of conflicting traffic reason)” (e.g., turbulence, mountain wave) Issue FL change or re−route, traffic permitting If not issued by the controller, request vector clear of traffic at adjacent FLs Issue PIREP to other aircraft If desired, request FL change or re−route Report location and magnitude of turbulence or MWA to ATC See Paragraph 4−6−6, Guidance on Severe Turbulence and Mountain Wave Activity (MWA) for detailed guidance. Paragraph 4−6−6 explains “traffic permitting.” Mountain Wave Activity (MWA) Encounters − General Pilot actions: Contact ATC and report experiencing MWA If so desired, pilot may request a FL change or re−route Report location and magnitude of MWA to ATC See paragraph 4−6−6 for guidance on MWA. Controller actions: Advise pilot of conflicting traffic at adjacent FL If pilot requests, vector aircraft to avoid merging target with traffic at adjacent RVSM flight levels, traffic permitting Issue FL change or re−route, traffic permitting Issue PIREP to other aircraft Paragraph 4−6−6 explains “traffic permitting.” NOTE− MWA encounters do not necessarily result in altitude deviations on the order of 200 feet. The guidance below is intended to address less significant MWA encounters. Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4−6−7 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 Wake Turbulence Encounters Pilot should: Contact ATC and request vector, FL change or, if capable, a lateral offset See Paragraph 4−6−7, Guidance on Wake Turbulence. Controller should: Issue vector, FL change or lateral offset clearance, traffic permitting Paragraph 4−6−6 explains “traffic permitting.” “Unable RVSM Due Equipment” Failure of Automatic Altitude Control System, Altitude Alerter or All Primary Altimeters Pilot will: Contact ATC and state “Unable RVSM Due Equipment” Request clearance out of RVSM airspace unless operational situation dictates otherwise Controller will: Provide 2,000 feet vertical separation or appropriate horizontal separation Clear aircraft out of RVSM airspace unless operational situation dictates otherwise One Primary Altimeter Remains Operational Pilot will: Cross check stand−by altimeter Notify ATC of operation with single primary altimeter Controller will: Acknowledge operation with single primary altimeter If unable to confirm primary altimeter accuracy, follow actions for failure of all primary altimeters Transponder Failure Pilot will: Contact ATC and request authority to continue to operate at cleared flight level Comply with revised ATC clearance, if issued Controller will: Consider request to continue to operate at cleared flight level Issue revised clearance, if necessary NOTE− 14 CFR Section 91.215 (ATC transponder and altitude reporting equipment and use) regulates operation with the transponder inoperative. 4−6−10. Procedures for Accommodation of Non−RVSM Aircraft a. General Policies for Accommodation of Non−RVSM Aircraft 1. The RVSM mandate calls for only RVSM authorized aircraft/operators to fly in designated RVSM airspace with limited exceptions. The policies detailed below are intended exclusively for use by aircraft that the FAA has agreed to accommodate. They are not intended to provide other operators a 4−6−8 means to circumvent the normal RVSM approval process. 2. If the operator is not authorized or the aircraft is not RVSM−compliant, the aircraft will be referred to as a “non−RVSM” aircraft. 14 CFR Section 91.180 and Part 91, Appendix G, enable the FAA to authorize a deviation to operate a non−RVSM aircraft in RVSM airspace. 3. Non−RVSM aircraft flights will be handled on a workload permitting basis. The vertical separation standard applied between aircraft not Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 12/2/21 6/17/21 approved for RVSM and all other aircraft must be 2,000 feet. 4. Required Pilot Calls. The pilot of non− RVSM aircraft will inform the controller of the lack of RVSM approval in accordance with the direction provided in Paragraph 4−6−8, Pilot/Controller Phraseology. b. Categories of Non−RVSM Aircraft that may be Accommodated Subject to FAA approval and clearance, the following categories of non−RVSM aircraft may operate in domestic U.S. RVSM airspace provided they have an operational transponder. 1. Department of Defense (DOD) aircraft. 2. Flights conducted for aircraft certification and development purposes. 3. Active air ambulance flights utilizing a “MEDEVAC” call sign. 4. Aircraft climbing/descending through RVSM flight levels (without intermediate level off) to/from FLs above RVSM airspace (Policies for these flights are detailed in paragraph 4−6−11, Non−RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off. 5. Foreign State (government) aircraft. AIM 2. File−and−Fly. File a flight plan to notify the FAA of their intention to request access to RVSM airspace. NOTE− Priority for access to RVSM airspace will be afforded to RVSM compliant aircraft, then File−and−Fly flights. 4−6−11. Non−RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off a. File−and−Fly. Operators of Non−RVSM aircraft climbing to and descending from RVSM flight levels should just file a flight plan. b. Non−RVSM aircraft climbing to and descending from flight levels above RVSM airspace will be handled on a workload permitting basis. The vertical separation standard applied in RVSM airspace between non−RVSM aircraft and all other aircraft must be 2,000 feet. c. Non−RVSM aircraft climbing to/descending from RVSM airspace can only be considered for accommodation provided: 1. Aircraft is capable of a continuous climb/descent and does not need to level off at an intermediate altitude for any operational considerations and c. Methods for operators of non−RVSM aircraft to request access to RVSM Airspace. Operators may: 2. Aircraft is capable of climb/descent at the normal rate for the aircraft. 1. LOA/MOU. Enter into a Letter of Agreement (LOA)/Memorandum of Understanding (MOU) with the RVSM facility (the Air Traffic facility that provides air traffic services in RVSM airspace). Operators must comply with LOA/MOU. d. Required Pilot Calls. The pilot of non−RVSM aircraft will inform the controller of the lack of RVSM approval in accordance with the direction provided in paragraph 4−6−8, Pilot/Controller Phraseology. Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4−6−9 5/19/22 6/17/21 AIM Section 7. Operational Policy/Procedures for the Gulf of Mexico 50 NM Lateral Separation Initiative 4−7−1. Introduction and General Policies a. Air traffic control (ATC) may apply 50 nautical mile (NM) lateral separation (i.e., lateral spacing) between airplanes authorized for Required Navigation Performance (RNP) 10 or RNP 4 operating in the Gulf of Mexico. 50 NM lateral separation may be applied in the following airspace: 1. Houston Oceanic Control Area (CTA)/Flight Information Region (FIR). 2. Gulf of Mexico portion of the Miami Oceanic CTA/FIR. 3. Monterrey CTA. 4. Merida High CTA within the Mexico FIR/UTA. b. Within the Gulf of Mexico airspace described above, pairs of airplanes whose flight plans indicate approval for PBN and either RNP 10 or RNP 4 may be spaced by ATC at lateral intervals of 50 NM. ATC will space any airplane without RNP 10 or RNP 4 capability such that at least 90 NM lateral separation is maintained with other airplanes in the Miami Oceanic CTA, and at least 100 NM separation is maintained in the Houston, Monterrey, and Merida CTAs. c. The reduced lateral separation allows more airplanes to fly on optimum routes/altitudes over the Gulf of Mexico. d. 50 NM lateral separation is not applied on routes defined by ground navigation aids or on Gulf RNAV Routes Q100, Q102, or Q105. e. Information useful for flight planning and operations over the Gulf of Mexico under this 50 NM lateral separation policy, as well as information on how to obtain RNP 10 or RNP 4 authorization, can be found in the West Atlantic Route System, Gulf of Mexico, and Caribbean Resource Guide for U.S. Operators located at: https://www.faa.gov/headquartersoffices/avs/ wat-gomex-and-caribbean-resource-guide f. Pilots should use Strategic Lateral Offset Procedures (SLOP) in the course of regular operations within the Gulf of Mexico CTAs. SLOP procedures and limitations are published in the U.S. Aeronautical Information Publication (AIP), ENR Section 7.1, General Procedures; Advisory Circular (AC) 91−70, Oceanic and Remote Continental Airspace Operations; and ICAO Document 4444, Procedures for Air Navigation Services – Air Traffic Management. 4−7−2. Accommodating Non−RNP 10 Aircraft a. Operators not authorized for RNP 10 or RNP 4 may still file for any route and altitude within the Gulf of Mexico CTAs. However, clearance on the operator’s preferred route and/or altitude will be provided as traffic allows for 90 or 100 NM lateral separation between the non−RNP 10 aircraft and any others. Priority will be given to RNP 10 or RNP 4 aircraft. b. Operators of aircraft not authorized RNP 10 or RNP 4 must include the annotation “RMK/NONRNP10” in Item 18 of their ATC flight plan. c. Pilots of non−RNP 10 aircraft are to remind ATC of their RNP status; i.e., report “negative RNP 10” upon initial contact with ATC in each Gulf CTA. d. Operators will likely benefit from the effort they invest to obtain RNP 10 or RNP 4 authorization, provided they are flying aircraft equipped to meet RNP 10 or RNP 4 standards. 4−7−3. Obtaining RNP 10 or RNP 4 Operational Authorization a. For U.S. operators, AC 90−105, Approval Guidance for RNP Operations and Barometric Vertical Navigation in the U.S. National Airspace System and in Oceanic and Remote Continental Airspace, provides the aircraft and operator qualification criteria for RNP 10 or RNP 4 authorizations. FAA personnel at flight standards district offices (FSDO) and certificate management offices (CMO) will use the guidance contained in AC 90−105 to evaluate an operator’s application for RNP 10 or RNP 4 authorization. Authorization to Operational Policy/Procedures for the Gulf of Mexico 50 NM Lateral Separation Initiative 4−7−1 71 10.65R CHG 2 AIM AIM 3/15/07 5/19/22 6/17/21 conduct RNP operations in oceanic airspace is provided to all U.S. operators through issuance of Operations Specification (OpSpec), Management Specification (MSpec), or Letter of Authorization (LOA) B036, as applicable to the nature of the operation; for example, Part 121, Part 91, etc. Operators may wish to review FAA Order 8900.1, Flight Standards Information Management System, volume 3, chapter 18, section 4, to understand the specific criteria for issuing OpSpec, MSpec, and/or LOA B036. b. The operator’s RNP 10 or RNP 4 authorization should include any equipment requirements and RNP 10 time limits (if operating solely inertial− based navigation systems), which must be observed when conducting RNP operations. RNP 4 requires tighter navigation and track maintenance accuracy than RNP 10. 4−7−4. Authority for Operations with a Single Long−Range Navigation System Operators may be authorized to take advantage of 50 NM lateral separation in the Gulf of Mexico CTAs when equipped with only a single long−range navigation system. RNP 10 with a single long−range navigation system is authorized via OpSpec, MSpec, or LOA B054. Operators should contact their FSDO or CMO to obtain information on the specific requirements for obtaining B054. Volume 3, chapter 18, section 4 of FAA Order 8900.1 provides the qualification criteria to be used by FAA aviation safety inspectors in issuing B054. 4−7−5. Flight Plan Requirements a. In order for an operator with RNP 10 or RNP 4 authorization to obtain 50 NM lateral separation in the Gulf of Mexico CTAs, and therefore obtain 4−7−2 preferred routing available to RNP authorized aircraft, the international flight plan form (FAA 7233−4) must be annotated as follows: “R.” 1. Item 10a (Equipment) must include the letter 2. Item 18 must include either “PBN/A1” for RNP 10 authorization or “PBN/L1” for RNP 4 authorization. b. Indication of RNP 4 authorization implies the aircraft and pilots are also authorized RNP 10. c. Chapter 5, section 1, of this manual includes information on all flight plan codes. RNP 10 has the same meaning and application as RNAV 10. They share the same code. 4−7−6. Contingency Procedures Pilots operating under reduced lateral separation must be particularly familiar with, and prepared to rapidly implement, the standard contingency procedures specifically written for operations when outside ATC surveillance and direct VHF communications (for example, the oceanic environment). Specific procedures have been developed for weather deviations. Operators should ensure all flight crews operating in this type of environment have been provided the standard contingency procedures in a readily accessible format. The margin for error when operating at reduced separation mandates correct and expeditious application of the standard contingency procedures. These internationally accepted procedures are published in ICAO Document 4444, chapter 15. The procedures are also reprinted in the U.S. Aeronautical Information Publication (AIP), En Route (ENR) Section 7.3, Special Procedures for In−flight Contingencies in Oceanic Airspace; and AC 91−70. Operational Policy/Procedures for the Gulf of Mexico 50 NM Lateral Separation Initiative 12/2/21 6/17/21 AIM Chapter 5. Air Traffic Procedures Section 1. Preflight 5−1−1. Preflight Preparation a. Prior to every flight, pilots should gather all information vital to the nature of the flight, assess whether the flight would be safe, and then file a flight plan. Pilots can receive a regulatory compliant briefing without contacting Flight Service. Pilots are encouraged to use automated resources and review Advisory Circular AC 91−92, Pilot’s Guide to a Preflight Briefing, for more information. Pilots who prefer to contact Flight Service are encouraged to conduct a self−brief prior to calling. Conducting a self−brief before contacting Flight Service provides familiarity of meteorological and aeronautical conditions applicable to the route of flight and promotes a better understanding of weather information. Pilots may access Flight Service through www.1800wxbrief.com or by calling 1−800−WX−BRIEF. Flight planning applications are also available for conducting a self−briefing and filing flight plans. NOTE− Alaska only: Pilots filing flight plans via “fast file” who desire to have their briefing recorded, should include a statement at the end of the recording as to the source of their weather briefing. b. The information required by the FAA to process flight plans is obtained from FAA Form 7233−4, International Flight Plan. Only DOD users, and civilians who file stereo route flight plans, may use FAA Form 7233−1, Flight Plan. NOTE− FAA and DOD Flight Plan Forms are equivalent. Where the FAA specifies Form 7233−1, Flight Plan and FAA Form 7233−4, International Flight Plan, the DOD may substitute their Form DD 175, Military Flight Plan and Form DD−1801, DOD International Flight Plan as necessary. NAS automation systems process and convert data in the same manner, although for computer acceptance, input fields may be adjusted to follow FAA format. c. FSSs are required to advise of pertinent NOTAMs if a standard briefing is requested, but if they are overlooked, do not hesitate to remind the specialist that you have not received NOTAM Preflight information. Additionally, FSS briefers do not provide FDC NOTAM information for special instrument approach procedures unless specifically asked. Pilots authorized by the FAA to use special instrument approach procedures must specifically request FDC NOTAM information for these procedures. Pilots who receive the information electronically will receive NOTAMs for special IAPs automatically. NOTE− Domestic Notices and International Notices are not provided during a briefing unless specifically requested by the pilot since the FSS specialist has no way of knowing whether the pilot has already checked the Federal NOTAM System (FNS) NOTAM Search website external links prior to calling. Airway NOTAMs, procedural NOTAMs, and NOTAMs that are general in nature and not tied to a specific airport/facility (for example, flight advisories and restrictions, open duration special security instructions, and special flight rules areas) are briefed solely by pilot request. Remember to ask for these notices if you have not already reviewed this information, and to request all pertinent NOTAMs specific to your flight. REFERENCE− AIM, Para 5−1−3, Notice to Air Missions (NOTAM) System. d. Pilots are urged to use only the latest issue of aeronautical charts in planning and conducting flight operations. Aeronautical charts are revised and reissued on a regular scheduled basis to ensure that depicted data are current and reliable. In the conterminous U.S., Sectional Charts are updated every 6 months, IFR En Route Charts every 56 days, and amendments to civil IFR Approach Charts are accomplished on a 56−day cycle with a change notice volume issued on the 28−day midcycle. Charts that have been superseded by those of a more recent date may contain obsolete or incomplete flight information. REFERENCE− AIM, Paragraph 9−1−4, General Description of Each Chart Series e. When requesting a preflight briefing, identify yourself as a pilot and provide the following: 1. Type of flight planned; e.g., VFR or IFR. 2. Aircraft’s number or pilot’s name. 3. Aircraft type. 5−1−1 7110.65R CHG 2 AIM AIM 4. Departure Airport. 5. Route of flight. 6. Destination. 7. Flight altitude(s). 8. ETD and ETE. f. Prior to conducting a briefing, briefers are required to have the background information listed above so that they may tailor the briefing to the needs of the proposed flight. The objective is to communicate a “picture” of meteorological and aeronautical information necessary for the conduct of a safe and efficient flight. Briefers use all available weather and aeronautical information to summarize data applicable to the proposed flight. Pilots who have briefed themselves before calling Flight Service should advise the briefer what information has been obtained from other sources. REFERENCE− AIM, Paragraph 7−1−5, Preflight Briefings, contains those items of a weather briefing that should be expected or requested. g. FAA by 14 CFR Part 93, Subpart K, has designated High Density Traffic Airports (HDTA) and has prescribed air traffic rules and requirements for operating aircraft (excluding helicopter operations) to and from these airports. REFERENCE− Chart Supplement U.S., Special Notices Section AIM, Paragraph 4−1−21, Airport Reservation Operations and Special Traffic Management Programs h. In addition to the filing of a flight plan, if the flight will traverse or land in one or more foreign countries, it is particularly important that pilots leave a complete itinerary with someone directly concerned and keep that person advised of the flight’s progress. If serious doubt arises as to the safety of the flight, that person should first contact the FSS. REFERENCE− AIM, Paragraph 5−1−11, Flights Outside the U.S. and U.S. Territories i. Pilots operating under provisions of 14 CFR Part 135 on a domestic flight without having an FAA assigned 3−letter designator, must prefix the normal registration (N) number with the letter “T” on flight plan filing; for example, TN1234B. REFERENCE− AIM, Paragraph 4−2−4, Aircraft Call Signs FAA Order JO 7110.65, Paragraph 2−3−5a, Aircraft Identity FAA Order JO 7110.10, Paragraph 6−2−1b1, Flight Plan Recording 5−1−2 3/15/07 12/2/21 6/17/21 5−1−2. Follow IFR Procedures Even When Operating VFR a. To maintain IFR proficiency, pilots are urged to practice IFR procedures whenever possible, even when operating VFR. Some suggested practices include: 1. Obtain a complete preflight briefing and check NOTAMs. Prior to every flight, pilots should gather all information vital to the nature of the flight. Pilots can receive a regulatory compliant briefing without contacting Flight Service. Pilots are encouraged to use automated resources and review AC 91−92, Pilot’s Guide to a Preflight Briefing, for more information. NOTAMs are available online from the Federal NOTAM System (FNS) NOTAM Search website (https://notams.aim.faa.gov/notamSearch/), private vendors, or on request from Flight Service. 2. File a flight plan. This is an excellent low cost insurance policy. The cost is the time it takes to fill it out. The insurance includes the knowledge that someone will be looking for you if you become overdue at your destination. Pilots can file flight plans either by using a website or by calling Flight Service. Flight planning applications are also available to file, activate, and close VFR flight plans. 3. Use current charts. 4. Use the navigation aids. Practice maintaining a good course−keep the needle centered. 5. Maintain a constant altitude which is appropriate for the direction of flight. 6. Estimate en route position times. 7. Make accurate and frequent position reports to the FSSs along your route of flight. b. Simulated IFR flight is recommended (under the hood); however, pilots are cautioned to review and adhere to the requirements specified in 14 CFR Section 91.109 before and during such flight. c. When flying VFR at night, in addition to the altitude appropriate for the direction of flight, pilots should maintain an altitude which is at or above the minimum en route altitude as shown on charts. This is especially true in mountainous terrain, where there is usually very little ground reference. Do not depend on your eyes alone to avoid rising unlighted terrain, or even lighted obstructions such as TV towers. Preflight 12/2/21 6/17/21 5−1−3. Notice to Air Missions (NOTAM) System a. General. The NOTAM system provides pilots with time critical aeronautical information that is temporary, or information to be published on aeronautical charts at a later date, or information from another operational publication. The NOTAM is cancelled when the information in the NOTAM is published on the chart or when the temporary condition is returned to normal status. NOTAMs may be disseminated up to 7 days before the start of activity. Pilots can access NOTAM information online via NOTAM Search at: https://notams.aim.faa.gov/notamSearch/ or from an FSS. b. Preflight. 14 CFR § 91.103, Preflight Action directs pilots to become familiar with all available information concerning a planned flight prior to departure, including NOTAMs. Pilots may change their flight plan based on available information. Current NOTAM information may affect: 1. Aerodromes. 2. Runways, taxiways, and ramp restrictions. 3. Obstructions. 4. Communications. 5. Airspace. 6. Status of navigational aids or radar service availability. 7. Other information essential to planned en route, terminal, or landing operations. c. ARTCC NOTAMs. Pilots should also review NOTAMs for the ARTCC area (for example, Washington Center (ZDC), Cleveland Center (ZOB), etc.) in which the flight will be operating. You can find the 3 letter code for each ARTCC on the FAA’s NOTAM webpage. These NOTAMs may affect the planned flight. Some of the operations include Central Altitude Reservation Function (CARF), Special Use Airspace (SUA), Temporary Flight Restrictions (TFR), Global Positioning System (GPS), Flight Data Center (FDC) changes to routes, wind turbine, and Unmanned Aircraft System (UAS). NOTE− NOTAM information is transmitted using ICAO contractions to reduce transmission time. See TBL 5−1−2 for a listing of the most commonly used contractions, or go Preflight AIM online to the following URL: https://www.notams.faa.gov/downloads/contractions.pdf. For a complete listing of approved NOTAM Contractions, see FAA JO Order 7340.2, Contractions. d. Destination Update. Pilots should also contact ATC or FSS while en route to obtain updated airfield information for their destination. This is particularly important when flying to the airports without an operating control tower. Snow removal, fire and rescue activities, construction, and wildlife encroachment, may pose hazards to pilots. This information may not be available to pilots prior to arrival/departure. e. NAVAID NOTAMs. Pilots should check NOTAMs to ensure NAVAIDs required for the flight are in service. A NOTAM is published when a NAVAID is out of service or Unserviceable (U/S). Although a NAVAID is deemed U/S and planned for removal from service, it may be a long time before that NAVAID is officially decommissioned and removed from charts. A NOTAM is the primary method of alerting pilots to its unavailability. It is recommended that pilots using VFR charts should regularly consult the Chart Update Bulletin. This bulletin identifies any updates to the chart that have not yet been accounted for. f. GPS NOTAMs. The FAA issues information on the status of GPS through the NOTAM system. Operators may find information on GPS satellite outages, GPS testing, and GPS anomalies by specifically searching for GPS NOTAMS prior to flight. 1. The NOTAM system uses the terms UNRELIABLE (UNREL), MAY NOT BE AVAILABLE (AVBL), and NOT AVAILABLE (AVBL) when describing the status of GPS. UNREL indicates the expected level of service of the GPS and/or WAAS may not be available. Pilots must then determine the adequacy of the signal for desired use. Aircraft should have additional navigation equipment for their intended route. NOTE− Unless associated with a known testing NOTAM, pilots should report GPS anomalies, including degraded operation and/or loss of service, as soon as possible via radio or telephone, and via the GPS Anomaly Reporting Form. (See 1−1−13.) 2. GPS operations may also be NOTAMed for testing. This is indicated in the NOTAM language with the name of the test in parenthesis. When GPS 5−1−3 7110.65R CHG 2 AIM AIM testing NOTAMS are published and testing is actually occurring, ATC will advise pilots requesting or cleared for a GPS or RNAV (GPS) approach, that GPS may not be available and request the pilot’s intentions. TBL 5−1−1 lists an example of a GPS testing NOTAM. g. NOTAM Classification. NOTAM information is classified as Domestic NOTAMs (NOTAM D), Flight Data Center (FDC) NOTAMs, International NOTAMs, or Military NOTAMs. 1. NOTAM (D) information is disseminated for all navigational facilities that are part of the National Airspace System (NAS), all public use aerodromes, seaplane bases, and heliports listed in the Chart Supplement. U.S. NOTAM (D) information includes taxiway closures, personnel and equipment near or crossing runways, and airport lighting aids that do not affect instrument approach criteria (i.e., VGSI). All NOTAM Ds must have one of the keywords listed in TBL 5−1−1, as the first part of the text after the location identifier. These keywords categorize NOTAM Ds by subject, for example, APRON (ramp), RWY (runway), SVC (Services), etc. There are several types of NOTAM Ds: (a) Aerodrome activity and conditions, to include field conditions. (b) Airspace to include CARF, SUA, and general airspace activity like UAS or pyrotechnics. (c) Visual and radio navigational aids. (d) Communication and services. (e) Pointer NOTAMs. NOTAMs issued to point to additional aeronautical information. When pointing to another NOTAM, the keyword in the pointer NOTAM must match the keyword in the original NOTAM. Pointer NOTAMs should be issued for, but are not limited to, TFRs, Airshows, Temporary SUA, major NAS system interruptions, etc. 2. FDC NOTAMs are issued when it is necessary to disseminate regulatory information. FDC NOTAMs include: 3/15/07 12/2/21 6/17/21 however, some TFRs provide relief if ATC permission is given to enter the area when requested. Online preflight resources for TFRs provide graphics and plain language interpretations. (c) High barometric pressure warning. (d) Laser light activity. (e) ADS−B, TIS−B, and FIS−B service availability. GPS. (f) Satellite−based systems such as WAAS or (g) Special Notices. 3. International NOTAMs are published in ICAO format per Annex 15 and distributed to multiple countries. (a) International NOTAMs issued by the U.S. NOTAM Office use Series A followed by 4 sequential numbers, a slant “/” and a 2−digit number representing the year the NOTAM was issued. International NOTAMs basically duplicate data found in a U.S. Domestic NOTAM. (b) Not every topic of a U.S. Domestic NOTAM is issued as an International NOTAM by the U.S. The U.S. International NOTAM will be linked to the appropriate U.S. Domestic NOTAM when possible. (c) International NOTAMs received by the FAA from other countries are stored in the U.S. NOTAM System. (d) The International NOTAM format includes a “Q” Line that can be easily read/parsed by a computer and allows the NOTAM to be displayed digitally. (1) Field A: ICAO location identifier or FIR affected by the NOTAM. (2) Field B: Start of Validity. (3) Field C: End of Validity (both in [Year][Month][Day][Hour][Minute] format). (4) Field D: (when present) Schedule. (5) Field E: Full NOTAM description. (a) Amendments to published IAPs and other current aeronautical charts. (6) Field F: (when present) Lowest altitude, or “SFC.” (b) Temporary Flight Restrictions (TFR) restrict entrance to a certain airspace at a certain time, (7) Field G: (when present) Highest altitude, or “UNL.” 5−1−4 Preflight 12/2/21 6/17/21 AIM (e) For more on International format, please see Annex 15. 4. Military NOTAMs are NOTAMs originated by the U.S. Air Force, Army, Marine, or Navy, and pertaining to military or joint−use navigational aids/airports that are part of the NAS. Military NOTAMs are published in the International NOTAM format and should be reviewed by users of a military or joint−use facility. h. Security NOTAMS: 1. U.S. Domestic Security NOTAMS are FDC NOTAMS that inform pilots of certain U.S. security activities or requirements, such as Special Security Instructions for aircraft operations to, from, within, or transitioning U.S. territorial airspace. These NOTAMS are found on the Federal NOTAM System (FNS) NOTAM Search website under the location designator KZZZ. 2. United States International Flight Prohibitions, Potential Hostile Situations, and Foreign Notices are issued by the FAA and are found on the Federal NOTAM System (FNS) NOTAM Search website under the location designator KICZ. TBL 5−1−1 NOTAM Keywords Keyword RWY . . . . . . . Example Definition Runway !BNA BNA RWY 18/36 CLSD YYMMDDHHMM−YYMMDDHHMM TWY . . . . . . . Example Taxiway !BTV BTV TWY C EDGE LGT OBSC YYMMDDHHMM−YYMMDDHHMM APRON . . . . . Example Apron/Ramp !BNA BNA APRON NORTH APN E 100FT CLSD YYMMDDHHMM−YYMMDDHHMM AD . . . . . . . . . Example Aerodrome !BET BET AD AP ELK NEAR MOVEMENT AREAS YYMMDDHHMM−YYMMDDHHMM OBST . . . . . . . Example Obstruction !SJT SJT OBST MOORED BALLOON WI AN AREA DEFINED AS 1NM RADIUS OF SJT 2430FT (510FT AGL) FLAGGED YYMMDDHHMM−YYMMDDHHMM NAV . . . . . . . . Example Navigation Aids !SHV SHV NAV ILS RWY 32 110.3 COMMISSIONED YYMMDDHHMM−PERM COM . . . . . . . Example Communications !INW INW COM REMOTE COM OUTLET 122.6 U/S YYMMDDHHMM−YYMMDDHHMM EST (Note* EST will auto cancel) SVC . . . . . . . . Example Services !ROA ROA SVC TWR COMMISSIONED YYMMDDHHMM−PERM AIRSPACE . . Example Airspace !MHV MHV AIRSPACE AEROBATIC ACFT WI AN AREA DEFINED AS 4.3NM RADIUS OF MHV 5500FT−10500FT AVOIDANCE ADZ CTC JOSHUA APP DLY YYMMDDHHMM−YYMMDDHHMM ODP . . . . . . . . Example Obstacle Departure Procedure !FDC 2/9700 DIK ODP DICKINSON − THEODORE ROOSEVELT RGNL, DICKINSON, ND. TAKEOFF MINIMUMS AND (OBSTACLE) DEPARTURE PROCEDURES AMDT 1... DEPARTURE PROCEDURE: RWY 25, CLIMB HEADING 250 TO 3500 BEFORE TURNING LEFT. ALL OTHER DATA REMAINS AS PUBLISHED. THIS IS TAKEOFF MINIMUMS AND (OBSTACLE) DEPARTURE PROCEDURES, AMDT 1A. YYMMDDHHMM−PERM Standard Instrument Departure !FDC x/xxxx DFW SID DALLAS/FORT WORTH INTL, DALLAS, TX. PODDE THREE DEPARTURE... CHANGE NOTES TO READ: RWYS 17C/R, 18L/R: DO NOT EXCEED 240KT UNTIL LARRN. RWYS 35L/C, 36L/R: DO NOT EXCEED 240KT UNTIL KMART YYMMDDHHMM−YYMMDDHHMM SID . . . . . . . . . Example STAR . . . . . . . Example Preflight Standard Terminal Arrival !FDC x/xxxx DCA STAR RONALD REAGAN WASHINGTON NATIONAL,WASHINGTON, DC. WZRRD TWO ARRIVAL... SHAAR TRANSITION: ROUTE FROM DRUZZ INT TO WZRRD INT NOT AUTHORIZED. AFTER DRUZZ INT EXPECT RADAR VECTORS TO AML VORTAC YYMMDDHHMM−YYMMDDHHMM 5−1−5 7110.65R CHG 2 AIM AIM Keyword CHART . . . . . Example DATA . . . . . . . Example IAP . . . . . . . . . Example VFP . . . . . . . . Example 3/15/07 12/2/21 6/17/21 Definition Chart !FDC 2/9997 DAL IAP DALLAS LOVE FIELD, DALLAS, TX. ILS OR LOC RWY 31R, AMDT 5... CHART NOTE: SIMULTANEOUS APPROACH AUTHORIZED WITH RWY 31L. MISSED APPROACH: CLIMB TO 1000 THEN CLIMBING RIGHT TURN TO 5000 ON HEADING 330 AND CVE R−046 TO FINGR INT/ CVE 36.4 DME AND HOLD. CHART LOC RWY 31L. THIS IS ILS OR LOC RWY 31R, AMDT 5A. YYMMDDHHMM−PERM Data !FDC 2/9700 DIK ODP DICKINSON − THEODORE ROOSEVELT RGNL, DICKINSON, ND. TAKEOFF MINIMUMS AND (OBSTACLE) DEPARTURE PROCEDURES AMDT 1... DEPARTURE PROCEDURE: RWY 25, CLIMB HEADING 250 TO 3500 BEFORE TURNING LEFT. ALL OTHER DATA REMAINS AS PUBLISHED. THIS IS TAKEOFF MINIMUMS AND (OBSTACLE) DEPARTURE PROCEDURES, AMDT 1A. YYMMDDHHMM−PERM Instrument Approach Procedure !FDC 2/9997 DAL IAP DALLAS LOVE FIELD, DALLAS, TX. ILS OR LOC RWY 31R, AMDT 5... CHART NOTE: SIMULTANEOUS APPROACH AUTHORIZED WITH RWY 31L. MISSED APPROACH: CLIMB TO 1000 THEN CLIMBING RIGHT TURN TO 5000 ON HEADING 330 AND CVE R−046 TO FINGR INT/ CVE 36.4 DME AND HOLD. CHART LOC RWY 31L. THIS IS ILS OR LOC RWY 31R, AMDT 5A. YYMMDDHHMM−PERM Visual Flight Procedures !FDC X/XXXX JFK VFP JOHN F KENNEDY INTL, NEW YORK, NY. PARKWAY VISUAL RWY 13L/R, ORIG...WEATHER MINIMUMS 3000 FOOT CEILING AND 3 MILES VISIBILITY. YYMMDDHHMM− YYMMDDHHMM ROUTE . . . . . Example Route !FDC x/xxxx ZFW ROUTE ZFW ZKC. V140 SAYRE (SYO) VORTAC, OK TO TULSA (TUL) VORTAC, OK MEA 4300. YYMMDDHHMM−YYMMDDHHMM EST SPECIAL . . . Example Special !FDC x/xxxx JNU SPECIAL JUNEAU INTERNATIONAL, JUNEAU, AK. LDA−2 RWY 8 AMDT 9 PROCEDURE TURN NA. YYMMDDHHMM−YYMMDDHHMM SECURITY . . Example Security !FDC x/xxxx FDC ...SPECIAL NOTICE... THIS IS A RESTATEMENT OF A PREVIOUSLY ISSUED ADVISORY NOTICE. IN THE INTEREST OF NATIONAL SECURITY AND TO THE EXTENT PRACTICABLE, PILOTS ARE STRONGLY ADVISED TO AVOID THE AIRSPACE ABOVE, OR IN PROXIMITY TO SUCH SITES AS POWER PLANTS (NUCLEAR, HYDRO−ELECTRIC, OR COAL), DAMS, REFINERIES, INDUSTRIAL COMPLEXES, MILITARY FACILITIES AND OTHER SIMILAR FACILITIES. PILOTS SHOULD NOT CIRCLE AS TO LOITER IN THE VICINITY OVER THESE TYPES OF FACILITIES. GPS TESTING Example Global Positioning System Testing !GPS 01/028 ZAB NAV GPS (YPG_AZ GPS 21−06)(INCLUDING WAAS, GBAS, AND ADS−B) MAYNOT BE AVBL WI A276NM RADIUS CENTERED AT 332347N1142221W (BLH108023) FL400−UNL, 232NM RADIUS AT FL250, 164NM RADIUS AT 100000FT 160NM RADIUS AT 4000FT AGL 126NM RADIUS AT 50FT AGL DLY 1830−2230 2101281830−2101292230 PRN (GPS) Example Pseudo−random noise code used to differentiate GPS satellites. This code allows any receiver to identify exactly which satellite(s) it is receiving. !GPS GPS NAV PRN 16 U/S 2109231600−2109242300EST TBL 5−1−2 Contractions Commonly Found in NOTAMs A ABN . . . . . . . . . . ACFT . . . . . . . . . ACT . . . . . . . . . . ADJ . . . . . . . . . . AGL . . . . . . . . . . ALS . . . . . . . . . . 5−1−6 Aerodrome Beacon Aircraft Active Adjacent Above Ground Level Approach Light System AP . . . . . . . . . . . Airport APN . . . . . . . . . . Apron APP . . . . . . . . . . Approach control office or approach control or approach control service ARST . . . . . . . . . Arresting (specify (part of) aircraft arresting equipment) ASDA . . . . . . . . . Accelerate Stop Distance Available ASPH . . . . . . . . . Asphalt AUTH . . . . . . . . Authorized or authorization AVBL . . . . . . . . . Available or availability Preflight 12/2/21 6/17/21 AIM AVGAS . . . . . . . Aviation gasoline AWOS . . . . . . . . Automatic Weather Observing System AZM . . . . . . . . . . Azimuth B BA . . . . . . . . . . . BCN . . . . . . . . . . BCST . . . . . . . . . BDRY . . . . . . . . . BLDG . . . . . . . . . BLW . . . . . . . . . . BTN . . . . . . . . . . Braking action Beacon (aeronautical ground light) Broadcast Boundary Building Below Between GA . . . . . . . . . . . GLD . . . . . . . . . . GND . . . . . . . . . . GP . . . . . . . . . . . GRVL . . . . . . . . . General aviation Glider Ground Glide Path Gravel HEL . . . . . . . . . . HGT . . . . . . . . . . HLDG . . . . . . . . HLP . . . . . . . . . . HVY . . . . . . . . . . Helicopter Height or height above Holding Heliport Heavy IFR . . . . . . . . . . . ILS . . . . . . . . . . . IM . . . . . . . . . . . . INOP . . . . . . . . . INT . . . . . . . . . . . Instrument Flight Rules Instrument Landing System Inner Marker Inoperative Intersection H C C . . . . . . . . . . . . . Center (preceded by runway designator number to identify a parallel runway) CD . . . . . . . . . . . Clearance delivery CIV . . . . . . . . . . . Civil CL . . . . . . . . . . . Centerline CLSD . . . . . . . . . Close or closed or closing COM . . . . . . . . . Communication CONC . . . . . . . . Concrete COND . . . . . . . . Condition CONS . . . . . . . . . Continuous CONST . . . . . . . Construction or constructed CPDLC . . . . . . . . Controller Pilot Data Link Communications CTC . . . . . . . . . . Contact CUST . . . . . . . . . Customs D DA . . . . . . . . . . . DEG . . . . . . . . . . DEP . . . . . . . . . . DER . . . . . . . . . . DH . . . . . . . . . . . DIST . . . . . . . . . . DLY . . . . . . . . . . DP . . . . . . . . . . . DPT . . . . . . . . . . DTHR . . . . . . . . . Decision altitude Degrees Depart or Departure Departure end of the runway Decision Height Distance Daily Dew Point Temperature Depth Displaced Runway Threshold E E ............. EB . . . . . . . . . . . EMERG . . . . . . . ENE . . . . . . . . . . EQPT . . . . . . . . . ESE . . . . . . . . . . EST . . . . . . . . . . East or eastern longititude Eastbound Emergency East−northeast Equipment East−southeast Estimate or estimated or estimation (message type designator) EXC . . . . . . . . . . Except F FL . . . . . . . . . . . . FREQ . . . . . . . . . FRI . . . . . . . . . . . FSS . . . . . . . . . . . FST . . . . . . . . . . . FT . . . . . . . . . . . . Flight level Frequency Friday Flight Service Station First Feet (dimensional unit) G G . . . . . . . . . . . . . Green Preflight I K KT . . . . . . . . . . . Knots L L . . . . . . . . . . . . . Left (preceded by runway designator number to identify a parallel runway) LAT . . . . . . . . . . Latitude LDA . . . . . . . . . . Landing Distance Available LDG . . . . . . . . . . Landing LEN . . . . . . . . . . Length LGT . . . . . . . . . . Light or lighting LGTD . . . . . . . . . Lighted LOC . . . . . . . . . . Localizer LONG . . . . . . . . Longitude M MAINT . . . . . . . MBST . . . . . . . . . MIL . . . . . . . . . . MIN . . . . . . . . . . MNT . . . . . . . . . . MON . . . . . . . . . MOV . . . . . . . . . Maintenance Microburst Military Minutes Monitor or monitoring or monitored Monday Move or moving or movement N............. NAVAID . . . . . . . NB . . . . . . . . . . . NDB . . . . . . . . . . NE . . . . . . . . . . . NEB . . . . . . . . . . NM . . . . . . . . . . . NNE . . . . . . . . . . NNW . . . . . . . . . NOV . . . . . . . . . . NW . . . . . . . . . . . NWB . . . . . . . . . North Navigational aid Northbound Nondirectional Radio Beacon Northeast Northeast bound Nautical Mile/s North−northeast North−northwest November Northwest Northwest bound OBSC . . . . . . . . . OBST . . . . . . . . . OPN . . . . . . . . . . OPS . . . . . . . . . . Obscure or obscured or obscuring Obstacle Open or opening or opened Operations N O 5−1−7 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 P PAPI . . . . . . . . . . PARL . . . . . . . . . PAX . . . . . . . . . . PCL . . . . . . . . . . PCT . . . . . . . . . . PERM . . . . . . . . . PJE . . . . . . . . . . . PLA . . . . . . . . . . PPR . . . . . . . . . . PRN . . . . . . . . . . PT . . . . . . . . . . . . Precision Approach Path Indicator Parallel Passenger/s Pilot Controlled Lighting Percent Permanent Parachute Jumping Activities Practice Low Approach Prior Permission Required Pseudo−random Navigation Procedure Turn R R . . . . . . . . . . . . . Red R . . . . . . . . . . . . . Right (preceded by runway designator number to identify a parallel runway) RAI . . . . . . . . . . . Runway Alignment Indicator RCL . . . . . . . . . . Runway Centerline RCLL . . . . . . . . . Runway Centerline Light REDL . . . . . . . . . Receive/Receiver RLLS . . . . . . . . . Runway Lead−in Light System RMK . . . . . . . . . Remark RTS . . . . . . . . . . Return to Service RTZL . . . . . . . . . Runway Touchdown Zone Light(s) RVR . . . . . . . . . . Runway Visual Range RWY . . . . . . . . . Runway S S ............. SA . . . . . . . . . . . SAT . . . . . . . . . . SB . . . . . . . . . . . . SE . . . . . . . . . . . . SEC . . . . . . . . . . SFC . . . . . . . . . . SN . . . . . . . . . . . SR . . . . . . . . . . . . SS . . . . . . . . . . . . SSR . . . . . . . . . . SSW . . . . . . . . . . STD . . . . . . . . . . SUN . . . . . . . . . . SW . . . . . . . . . . . SWB . . . . . . . . . . South or southern latitude Sand Saturday Southbound Southeast Seconds Surface Snow Sunrise Sunset Secondary surveillance radar South−southwest Standard Sunday Southwest Southwest bound T TAR . . . . . . . . . . TAX . . . . . . . . . . TDZ . . . . . . . . . . TEMPO . . . . . . . TFC . . . . . . . . . . THR . . . . . . . . . . THU . . . . . . . . . . TKOF . . . . . . . . . TODA . . . . . . . . . TORA . . . . . . . . . TRG . . . . . . . . . . TUE . . . . . . . . . . TWR . . . . . . . . . . 5−1−8 Terminal area surveillance radar Taxing or taxiing Touchdown Zone Temporary or temporarily Traffic Threshold Thursday Takeoff Take−off Distance Available Take−off Run Available Training Tuesday Aerodrome Control Tower TWY . . . . . . . . . Taxiway TX . . . . . . . . . . . Taxilane U U/S . . . . . . . . . . . UAS . . . . . . . . . . UNL . . . . . . . . . . UNREL . . . . . . . Unserviceable Unmanned Aircraft System Unlimited Unreliable VIS . . . . . . . . . . . VOR . . . . . . . . . . VORTAC . . . . . . VOT . . . . . . . . . . Visibility VHF Omni-Directional Radio Range VOR and TACAN (collocated) VOR Test Facility W ............ WB . . . . . . . . . . . WDI . . . . . . . . . . WED . . . . . . . . . WI . . . . . . . . . . . WID . . . . . . . . . . WIP . . . . . . . . . . WNW . . . . . . . . . WS . . . . . . . . . . . WSW . . . . . . . . . West or western longitude Westbound Wind Direction Indicator Wednesday Within Width or wide Work in progress West−northwest Wind shear West−southwest V W 5−1−4. Operational Information System (OIS) a. The FAA’s Air Traffic Control System Command Center (ATCSCC) maintains a website with near real−time National Airspace System (NAS) status information. NAS operators are encouraged to access the website at http://www.fly.faa.gov prior to filing their flight plan. b. The website consolidates information from advisories. An advisory is a message that is disseminated electronically by the ATCSCC that contains information pertinent to the NAS. 1. Advisories are normally issued for the following items: (a) Ground Stops. (b) Ground Delay Programs. (c) Route Information. (d) Plan of Operations. (e) Facility Outages and Scheduled Facility Outages. (f) Volcanic Ash Activity Bulletins. (g) Special Traffic Management Programs. 2. This list is not all−inclusive. Any time there is information that may be beneficial to a large Preflight 12/2/21 6/17/21 number of people, an advisory may be sent. Additionally, there may be times when an advisory is not sent due to workload or the short length of time of the activity. 3. Route information is available on the website and in specific advisories. Some route information, subject to the 56−day publishing cycle, is located on the “OIS” under “Products,” Route Management Tool (RMT), and “What’s New” Playbook. The RMT and Playbook contain routings for use by Air Traffic and NAS operators when they are coordinated “real−time” and are then published in an ATCSCC advisory. 4. Route advisories are identified by the word “Route” in the header; the associated action is required (RQD), recommended (RMD), planned (PLN), or for your information (FYI). Operators are expected to file flight plans consistent with the Route RQD advisories. 5. Electronic System Impact Reports are on the intranet at http://www.atcscc.faa.gov/ois/ under “System Impact Reports.” This page lists scheduled outages/events/projects that significantly impact the NAS; for example, runway closures, air shows, and construction projects. Information includes anticipated delays and traffic management initiatives (TMI) that may be implemented. 5−1−5. Flight Plan − VFR Flights (See Appendix 4, FAA Form 7233−4 – International Flight Plan) a. The requirements for the filing and activation of VFR flight plans can vary depending in which airspace the flight is operating. Pilots are responsible for activating flight plans with a Flight Service Station. Control tower personnel do not automatically activate VFR flight plans. 1. Within the continental U.S., a VFR flight plan is not normally required. 2. VFR flights (except for DOD and law enforcement flights) into an Air Defense Identification Zone (ADIZ) are required to file DVFR flight plans. NOTE− Detailed ADIZ procedures are found inSection 6, National Preflight AIM Security and Interception Procedures, of this chapter. (See 14 CFR Part 99). 3. Flights within the Washington, DC Special Flight Rules Area have additional requirements that must be met. Visit http://www.faasafety.gov for the required Special Awareness Training that must be completed before flight within this area. 4. VFR flight to an international destination requires a filed and activated flight plan. NOTE− ICAO flight plan guidance is published in ICAO Document 4444 PANS−ATM Appendix 2. b. It is strongly recommended that a VFR flight plan be filed with a Flight Service Station or equivalent flight plan filing service. When filing, pilots must use FAA Form 7233−4, International Flight Plan or DD Form 1801. Only DOD users, and civilians who file stereo route flight plans, may use FAA Form 7233−1, Flight Plan. Pilots may take advantage of advances in technology by filing their flight plans using any available electronic means. Activating the flight plan will ensure that you receive VFR Search and Rescue services. c. When a stopover flight is anticipated, it is recommended that a separate flight plan be filed for each leg of the flight. d. Pilots are encouraged to activate their VFR flight plans with Flight Service by the most expeditious means possible. This may be via radio or other electronic means. VFR flight plan proposals are normally retained for two hours following the proposed time of departure. e. Pilots may also activate a VFR flight plan by using an assumed departure time. This assumed departure time will cause the flight plan to become active at the designated time. This may negate the need for communication with a flight service station or flight plan filing service upon departure. It is the pilot’s responsibility to revise his actual departure time, time en route, or ETA with flight service. NOTE− Pilots are strongly advised to remain mindful when using an assumed departure time. If not updated, search and rescue activities will be based on the assumed departure time. f. U.S. air traffic control towers do not routinely activate VFR flight plans. Foreign pilots especially must be mindful of the need to communicate directly 5−1−9 7110.65R CHG 2 AIM AIM with a flight service station, or use an assumed departure time procedure clearly communicated with the flight plan filing service. g. Although position reports are not required for VFR flight plans, periodic reports to FSSs along the route are good practice. Such contacts permit significant information to be passed to the transiting aircraft and also serve to check the progress of the flight should it be necessary for any reason to locate the aircraft. h. Pilots flying VFR should fly an appropriate cruising altitude for their direction of flight. i. When filing a VFR Flight plan, indicate the appropriate aircraft equipment capability as prescribed for an IFR flight plan. REFERENCE− AIM, Para 5−1−6, IFR Flights. j. ATC radar history data can be useful in finding a downed or missing aircraft; therefore, surveillance equipment should be listed in Item 18. Pilots using commercial GPS tracking services are encouraged to note the specific service in Item 19 N/ (survival equip remarks) of FAA Form 7233−4 or DD Form 1801. 5−1−6. Flight Plan − IFR Flights (See Appendix 4, FAA Form 7233−4 – International Flight Plan) a. General 1. Use of FAA Form 7233−4 or DD Form 1801 is mandatory for: (a) Assignment of RNAV SIDs and STARs or other PBN routing, (b) All civilian IFR flights that will depart U.S. domestic airspace, and (c) Domestic IFR flights except military/ DOD and civilians who file stereo route flight plans. (d) All military/DOD IFR flights that will depart U.S. controlled airspace. 2. Military/DOD flights using FAA Form 7233−1, or DD Form 175, may not be eligible for assignment of RNAV SIDs or STARs. Military flights desiring assignment of these procedures should file using FAA Form 7233−4 or DD 1801, as described in this section. 5−1−10 3/15/07 5/19/22 6/17/21 3. When filing an IFR flight plan using FAA Form 7233−4 or DD Form 1801, it is recommended that filers include all operable navigation, communication, and surveillance equipment capabilities by adding appropriate equipment qualifiers as shown in Appendix 4, FAA Form 7233−4, International Flight Plan. 4. ATC issues clearances based on aircraft capabilities filed in Items 10 and 18 of FAA Form 7233−4 or DD 1801. Operators should file all capabilities for which the aircraft and crew is certified, capable, and authorized. PBN/capability must be filed in Item 18, Other Information. When filing a capability, ATC expects filers to use that capability; for example, answer a SATVOICE call from ATC if code M1 or M3 is filed in Item 10a. 5. Prior to departure from within, or prior to entering controlled airspace, a pilot must submit a complete flight plan and receive an air traffic clearance, if weather conditions are below VFR minimums. IFR flight plans may be submitted to an FSS or flight plan filing service. 6. Pilots should file IFR flight plans at least 30 minutes prior to estimated time of departure to preclude possible delay in receiving a departure clearance from ATC. 7. In order to provide FAA traffic management units’ strategic route planning capabilities, nonscheduled operators conducting IFR operations above FL 230 are requested to voluntarily file IFR flight plans at least 4 hours prior to estimated time of departure (ETD). 8. To minimize your delay in entering Class B, Class C, Class D, and Class E surface areas at destination when IFR weather conditions exist or are forecast at that airport, an IFR flight plan should be filed before departure. Otherwise, a 30−minute delay is not unusual in receiving an ATC clearance because of time spent in processing flight plan data. 9. Traffic saturation frequently prevents control personnel from accepting flight plans by radio. In such cases, the pilot is advised to contact a flight plan filing service for the purpose of filing the flight plan. 10. When requesting an IFR clearance, it is highly recommended that the departure airport be identified by stating the city name and state and/or the airport location identifier in order to clarify to ATC the exact location of the intended airport of departure. Preflight 12/2/21 6/17/21 11. Multiple versions of flight plans for the same flight may lead to unsafe conditions and errors within the air traffic system. Pilots must not file more than one flight plan for the same flight without ensuring that the previous flight plan has been successfully removed. 12. When a pilot is aware that the possibility for multiple flight plans on the same aircraft may exist, ensuring receipt of a full route clearance will help mitigate chances of error. REFERENCE− AIM, Para 5−1−12, Change in Flight Plan. AIM, Para 5−1−13, Change in Proposed Departure Time. b. Airways and Jet Routes Depiction on Flight Plan 1. It is vitally important that the route of flight be accurately and completely described in the flight plan. To simplify definition of the proposed route, and to facilitate ATC, pilots are requested to file via airways or jet routes established for use at the altitude or flight level planned. 2. If flight is to be conducted via designated airways or jet routes, describe the route by indicating the type and number designators of the airway(s) or jet route(s) requested. If more than one airway or jet route is to be used, clearly indicate points of transition. If the transition is made at an unnamed intersection, show the next succeeding NAVAID or named intersection on the intended route and the complete route from that point. Reporting points may be identified by using authorized name/code as depicted on appropriate aeronautical charts. The following two examples illustrate the need to specify the transition point when two routes share more than one transition fix. EXAMPLE− 1. ALB J37 BUMPY J14 BHM Spelled out: from Albany, New York, via Jet Route 37 transitioning to Jet Route 14 at BUMPY intersection, thence via Jet Route 14 to Birmingham, Alabama. 2. ALB J37 ENO J14 BHM Spelled out: from Albany, New York, via Jet Route 37 transitioning to Jet Route 14 at Smyrna VORTAC (ENO) thence via Jet Route 14 to Birmingham, Alabama. 3. The route of flight may also be described by naming the reporting points or NAVAIDs over which the flight will pass, provided the points named are established for use at the altitude or flight level planned. Preflight AIM EXAMPLE− BWI V44 SWANN V433 DQO Spelled out: from Baltimore−Washington International, via Victor 44 to Swann intersection, transitioning to Victor 433 at Swann, thence via Victor 433 to Dupont. 4. When the route of flight is defined by named reporting points, whether alone or in combination with airways or jet routes, and the navigational aids (VOR, VORTAC, TACAN, NDB) to be used for the flight are a combination of different types of aids, enough information should be included to clearly indicate the route requested. EXAMPLE− LAX J5 LKV J3 GEG YXC FL 330 J500 VLR J515 YWG Spelled out: from Los Angeles International via Jet Route 5 Lakeview, Jet Route 3 Spokane, direct Cranbrook, British Columbia VOR/DME, Flight Level 330 Jet Route 500 to Langruth, Manitoba VORTAC, Jet Route 515 to Winnipeg, Manitoba. 5. When filing IFR, it is to the pilot’s advantage to file a preferred route. REFERENCE− Preferred IFR Routes are described and tabulated in the Chart Supplement U.S. Additionally available at U.S. http://www.fly.faa.gov/Products/Coded_Departure_Routes/NFDC_Pref erred_Routes_Database/nfdc_preferred_routes_database.html. 6. ATC may issue a SID or a STAR, as appropriate. REFERENCE− AIM, Para 5−2−9, Instrument Departure Procedures (DP) − Obstacle Departure Procedures (ODP) and Standard Instrument Departures (SID), and Diverse Vector Areas (DVA). AIM, Para 5−4−1, Standard Terminal Arrival (STAR) Procedures. NOTE− Pilots not desiring an RNAV SID or RNAV STAR should enter in Item #18, PBN code: NAV/RNV A0 and/or D0. c. Direct Flights 1. All or any portions of the route which will not be flown on the radials or courses of established airways or routes, such as direct route flights, must be defined by indicating the radio fixes over which the flight will pass. Fixes selected to define the route must be those over which the position of the aircraft can be accurately determined. Such fixes automatically become compulsory reporting points for the flight, unless advised otherwise by ATC. Only those navigational aids established for use in a particular structure; i.e., in the low or high structures, may be used to define the en route phase of a direct flight within that altitude structure. 2. The azimuth feature of VOR aids and the azimuth and distance (DME) features of VORTAC 5−1−11 7110.65R CHG 2 AIM AIM and TACAN aids are assigned certain frequency protected areas of airspace which are intended for application to established airway and route use, and to provide guidance for planning flights outside of established airways or routes. These areas of airspace are expressed in terms of cylindrical service volumes of specified dimensions called “class limits” or “categories.” REFERENCE− AIM, Para 1−1−8, Navigational Aid (NAVAID) Service Volumes. 3. An operational service volume has been established for each class in which adequate signal coverage and frequency protection can be assured. To facilitate use of VOR, VORTAC, or TACAN aids, consistent with their operational service volume limits, pilot use of such aids for defining a direct route of flight in controlled airspace should not exceed the following: (a) Operations above FL 450 − Use aids not more than 200 NM apart. These aids are depicted on en route high altitude charts. 3/15/07 12/2/21 6/17/21 Chicago Midway Airport via Victor 262 to Bradford, Victor 10 to Burlington, Iowa, direct St. Joseph, Missouri, direct Salina, Kansas, direct Garden City, Kansas. NOTE− When route of flight is described by radio fixes, the pilot will be expected to fly a direct course between the points named. 7. Pilots are reminded that they are responsible for adhering to obstruction clearance requirements on those segments of direct routes that are outside of controlled airspace and ATC surveillance capability. The MEAs and other altitudes shown on IFR en route charts pertain to those route segments within controlled airspace, and those altitudes may not meet obstruction clearance criteria when operating off those routes. NOTE− Refer to 14 CFR 91.177 for pilot responsibility when flying random point to point routes. d. Area Navigation (RNAV)/Global Navigation Satellite System (GNSS) (b) Operation off established routes from 18,000 feet MSL to FL 450 − Use aids not more than 260 NM apart. These aids are depicted on en route high altitude charts. 1. When not being radar monitored, GNSS− equipped RNAV aircraft on random RNAV routes must be cleared via or reported to be established on a point−to−point route. (c) Operation off established airways below 18,000 feet MSL − Use aids not more than 80 NM apart. These aids are depicted on en route low altitude charts. (a) The points must be published NAVAIDs, waypoints, fixes or airports recallable from the aircraft’s navigation database. The points must be displayed on controller video maps or depicted on the controller chart displayed at the control position. When applying non−radar separation the maximum distance between points must not exceed 500 miles. (d) Operation off established airways between 14,500 feet MSL and 17,999 feet MSL in the conterminous U.S. − (H) facilities not more than 200 NM apart may be used. 4. Increasing use of self−contained airborne navigational systems which do not rely on the VOR/VORTAC/TACAN system has resulted in pilot requests for direct routes which exceed NAVAID service volume limits. 5. At times, ATC will initiate a direct route in a surveillance environment which exceeds NAVAID service volume limits. Pilots must adhere to the altitude specified in the clearance. (b) ATC will protect 4 miles either side of the route centerline. (c) Assigned altitudes must be at or above the highest MIA along the projected route segment being flown, including the protected airspace of that route segment. 2. Pilots of aircraft equipped with approved area navigational equipment may file for RNAV routes throughout the National Airspace System in accordance with the following procedures: (a) File airport−to−airport flight plans. 6. Appropriate airway or jet route numbers may also be included to describe portions of the route to be flown. (b) File the appropriate indication of RNAV and/or RNP capability in the flight plan. EXAMPLE− MDW V262 BDF V10 BRL STJ SLN GCK Spelled out: from (c) Plan the random route portion of the flight plan to begin and end over appropriate arrival and 5−1−12 Preflight 12/2/21 6/17/21 departure transition fixes or appropriate navigation aids for the altitude stratum within which the flight will be conducted. The use of normal preferred departure and arrival routes (DP/STAR), where established, is recommended. (d) File route structure transitions to and from the random route portion of the flight. (e) Define the random route by waypoints. File route description waypoints by using degree distance fixes based on navigational aids which are appropriate for the altitude stratum. (f) File a minimum of one route description waypoint for each ARTCC through whose area the random route will be flown. These waypoints must be located within 200 NM of the preceding center’s boundary. (g) File an additional route description waypoint for each turn point in the route. (h) Plan additional route description waypoints as required to ensure accurate navigation via the filed route of flight. Navigation is the pilot’s responsibility unless ATC assistance is requested. (i) Plan the route of flight so as to avoid prohibited and restricted airspace by 3 NM unless permission has been obtained to operate in that airspace and the appropriate ATC facilities are advised. NOTE− To be approved for use in the National Airspace System, RNAV equipment must meet system availability, accuracy, and airworthiness standards. For additional information and guidance on RNAV equipment requirements see Advisory Circular (AC) 20−138 Airworthiness Approval of Positioning and Navigation Systems and AC 90−100 U.S. Terminal and En Route Area Navigation (RNAV) Operations. AIM airports without published transition procedures. The use of preferred departure and arrival routes, such as DP and STAR, where established, is recommended. (d) Plan the route of flight so as to avoid prohibited and restricted airspace by 3 NM unless permission has been obtained to operate in that airspace and the appropriate ATC facility is advised. (e) Define the route of flight after the departure fix, including each intermediate fix (turnpoint) and the arrival fix for the destination airport in terms of latitude/longitude coordinates plotted to the nearest minute or in terms of Navigation Reference System (NRS) waypoints. For latitude/ longitude filing the arrival fix must be identified by both the latitude/longitude coordinates and a fix identifier. EXAMPLE− MIA 1 SRQ 2 3407/10615 3 3407/11546 TNP 4 LAX 5 1 Departure airport. 2 Departure fix. 3 Intermediate fix (turning point). 4 Arrival fix. 5 Destination airport. or ORD 1 IOW 2 KP49G 3 KD34U 4 KL16O 5 OAL 6 MOD2 7 SFO 8 1 Departure airport. 2 Transition fix. 3 Minneapolis ARTCC waypoint. 4 Denver ARTCC Waypoint. 5 Los Angeles ARTCC waypoint. 6 Transition fix. 7 Arrival. 8 Destination airport. 3. Pilots of aircraft equipped with latitude/longitude coordinate navigation capability, independent of VOR/TACAN references, may file for random RNAV using the following procedures: (f) Record latitude/longitude coordinates by two or four figures describing latitude in degrees followed by an N or S, followed by 3 or 5 digits longitude, followed by an E or W. Separate latitude and longitude with a solidus “/.” Use leading zeros if necessary. (a) File airport−to−airport flight plans prior to departure. (g) File at FL 390 or above for the random RNAV portion of the flight. (b) File the appropriate RNAV capability certification suffix in the flight plan. (h) Fly all routes/route segments on Great Circle tracks. (c) Plan the random route portion of the flight to begin and end over published departure/arrival transition fixes or appropriate navigation aids for (i) Make any inflight requests for random RNAV clearances or route amendments to an en route ATC facility. Preflight 5−1−13 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 5−1−7. Flight Plans For Military/DOD Use Only 5−1−9. Single Flights Conducted With Both VFR and IFR Flight Plans (See Appendix 4, FAA Form 7233−1, Flight Plan) a. Flight plans which combine VFR operation on an active VFR flight plan for one portion of a flight, and IFR for another portion, sometimes known as a composite flight plan, cannot be accepted or processed by current en route automation systems. Within U.S. controlled airspace, FAA Form 7233−1 or DD Form 175 may be used by DOD aircraft. However, use of the DD Form 1801 by DOD aircraft is recommended for IFR flights and is mandatory for: a. Any flight that will depart U.S. controlled airspace. b. Any flight requesting routing that requires Performance Based Navigation. c. Any flight requesting services that require filing of capabilities only supported in the international flight plan. NOTE− 1. The order of flight plan elements in DD Form 175 is equivalent to that of FAA Form 7233−1. 2. Civilians who file stereo route flight plans, may use FAA Form 7233−1, Flight Plan. 5−1−8. Flight Plan – Defense VFR (DVFR) Flights VFR flights (except for DOD and law enforcement flights) into an ADIZ are required to file DVFR flight plans for security purposes. Detailed ADIZ procedures are found in Section 6, National Security and Interception Procedures, of this chapter. REFERENCE− 14 CFR Part 99, Security Control for Air Traffic. a. DVFR flight plans must be filed using FAA Form 7233−4 or DD Form 1801. b. Enter the letter “D” in Item 8, Type of Flight, of FAA Form 7233−4 or DD Form 1801. c. DVFR flights where pilots decline search and rescue coverage must clearly indicate “NORIV” in Item 18 following the indicator “RMK/.” This flight plan must still be activated in order to properly notify NORAD, however no flight plan cancellation will be expected. EXAMPLE− RMK/NORIV 5−1−14 b. Pilots are free to operate VFR in VFR conditions prior to accepting an IFR clearance from the appropriate control facility, or may cancel an IFR clearance and proceed VFR as desired. However, if a pilot desires to be on an active VFR flight plan, with search and rescue provisions, for the portion of flight not conducted under an IFR clearance, a separate VFR flight plan must be filed, activated, and closed. c. If a pilot desires to be on an active VFR flight plan prior to or following the IFR portion of the flight, that flight plan must be filed and processed as a distinct and separate flight plan. The VFR flight plan must be opened and closed with either a Flight Service Station or other service provider having the capability to open and close VFR flight plans. Air Traffic Control does not have the ability to determine if an aircraft is operating on an active VFR flight plan and cannot process the activation or cancellation of a VFR flight plan. d. Pilots may propose to commence the IFR portion of flight at a defined airborne point. This airborne point, or fix, is entered as the departure point in Item 13 of FAA Form 7233−4 or DD Form 1801. e. Pilots may indicate in the IFR flight plan the intention to terminate the IFR portion of flight at any defined airborne point. The airborne point, or fix, is entered as the destination point in Item 16 of FAA Form 7233−4 or DD Form 1801. f. Prior to beginning the IFR portion of flight, a pilot must receive an IFR clearance from the appropriate control facility. g. If the pilot does not desire further clearance after reaching the clearance limit, he or she must advise ATC to cancel the IFR clearance. 5−1−10. IFR Operations to High Altitude Destinations a. Pilots planning IFR flights to airports located in mountainous terrain are cautioned to consider the necessity for an alternate airport even when the Preflight 12/2/21 6/17/21 AIM forecast weather conditions would technically relieve them from the requirement to file one. 5−1−11. Flights Outside U.S. Territorial Airspace REFERENCE− 14 CFR Section 91.167. AIM, Paragraph 4−1−19 , Tower En Route Control (TEC) a. When conducting flights, particularly extended flights, outside the U.S. and its territories, full account should be taken of the amount and quality of air navigation services available in the airspace to be traversed. Every effort should be made to secure information on the location and range of navigational aids, availability of communications and meteorological services, the provision of air traffic services, including alerting service, and the existence of search and rescue services. b. The FAA has identified three possible situations where the failure to plan for an alternate airport when flying IFR to such a destination airport could result in a critical situation if the weather is less than forecast and sufficient fuel is not available to proceed to a suitable airport. 1. An IFR flight to an airport where the Minimum Descent Altitudes (MDAs) or landing visibility minimums for all instrument approaches are higher than the forecast weather minimums specified in 14 CFR Section 91.167(b). For example, there are 3 high altitude airports in the U.S. with approved instrument approach procedures where all of the MDAs are greater than 2,000 feet and/or the landing visibility minimums are greater than 3 miles (Bishop, California; South Lake Tahoe, California; and Aspen−Pitkin Co./Sardy Field, Colorado). In the case of these airports, it is possible for a pilot to elect, on the basis of forecasts, not to carry sufficient fuel to get to an alternate when the ceiling and/or visibility is actually lower than that necessary to complete the approach. 2. A small number of other airports in mountainous terrain have MDAs which are slightly (100 to 300 feet) below 2,000 feet AGL. In situations where there is an option as to whether to plan for an alternate, pilots should bear in mind that just a slight worsening of the weather conditions from those forecast could place the airport below the published IFR landing minimums. 3. An IFR flight to an airport which requires special equipment; i.e., DME, glide slope, etc., in order to make the available approaches to the lowest minimums. Pilots should be aware that all other minimums on the approach charts may require weather conditions better than those specified in 14 CFR Section 91.167(b). An inflight equipment malfunction could result in the inability to comply with the published approach procedures or, again, in the position of having the airport below the published IFR landing minimums for all remaining instrument approach alternatives. Preflight b. Pilots should remember that there is a need to continuously guard the VHF emergency frequency 121.5 MHz when on long over-water flights, except when communications on other VHF channels, equipment limitations, or cockpit duties prevent simultaneous guarding of two channels. Guarding of 121.5 MHz is particularly critical when operating in proximity to Flight Information Region (FIR) boundaries, for example, operations on Route R220 between Anchorage and Tokyo, since it serves to facilitate communications with regard to aircraft which may experience in-flight emergencies, communications, or navigational difficulties. REFERENCE− ICAO Annex 10, Vol II, Paras 5.2.2.1.1.1 and 5.2.2.1.1.2. c. The filing of a flight plan, always good practice, takes on added significance for extended flights outside U.S. airspace and is, in fact, usually required by the laws of the countries being visited or overflown. It is also particularly important in the case of such flights that pilots leave a complete itinerary and schedule of the flight with someone directly concerned and keep that person advised of the flight’s progress. If serious doubt arises as to the safety of the flight, that person should first contact the appropriate FSS. Round Robin Flight Plans to Canada and Mexico are not accepted. d. All pilots should review the foreign airspace and entry restrictions published in the appropriate Aeronautical Information Publication (AIP) during the flight planning process. Foreign airspace penetration without official authorization can involve both danger to the aircraft and the imposition of severe penalties and inconvenience to both passengers and crew. A flight plan on file with ATC authorities does not necessarily constitute the prior permission required by certain other authorities. The 5−1−15 7110.65R CHG 2 AIM AIM possibility of fatal consequences cannot be ignored in some areas of the world. e. Current NOTAMs for foreign locations must also be reviewed. International Notices regarding specific countries may be obtained through the Federal NOTAM System (FNS) NOTAM Search External Links or the Air Traffic Plans and Publications website. For additional flight information at foreign locations, pilots should also review the FAA’s Prohibitions, Restrictions, and Notices website at https://www.faa.gov/air_traffic/publications/us_ restrictions/. f. When customs notification to foreign locations is required, it is the responsibility of the pilot to arrange for customs notification in a timely manner. g. Aircraft arriving to locations in U.S. territorial airspace must meet the entry requirements as described in AIM Section 6, National Security and Interception Procedures. 5−1−12. Change in Flight Plan a. In addition to altitude or flight level, destination and/or route changes, increasing or decreasing the speed of an aircraft constitutes a change in a flight plan. Therefore, at any time the average true airspeed at cruising altitude between reporting points varies or is expected to vary from that given in the flight plan by plus or minus 5 percent, or 10 knots, whichever is greater, ATC should be advised. b. All changes to existing flight plans should be completed more than 46 minutes prior to the proposed departure time. Changes must be made with the initial flight plan service provider. If the initial flight plan’s service provider is unavailable, filers may contact an ATC facility or FSS to make the necessary revisions. Any revision 46 minutes or less from the proposed departure time must be coordinated through an ATC facility or FSS. 5−1−13. Change in Proposed Departure Time a. To prevent computer saturation in the en route environment, parameters have been established to delete proposed departure flight plans which have not been activated. Most centers have this parameter set so as to delete these flight plans a minimum of 2 hours after the proposed departure time or Expect 5−1−16 3/15/07 12/2/21 6/17/21 Departure Clearance Time (EDCT). To ensure that a flight plan remains active, pilots whose actual departure time will be delayed 2 hours or more beyond their filed departure time, are requested to notify ATC of their new proposed departure time. b. Due to traffic saturation, ATC personnel frequently will be unable to accept these revisions via radio. It is recommended that you forward these revisions to a flight plan service provider or FSS. 5−1−14. Closing VFR/DVFR Flight Plans A pilot is responsible for ensuring that his/her VFR or DVFR flight plan is canceled. You should close your flight plan with the nearest FSS, or if one is not available, you may request any ATC facility to relay your cancellation to the FSS. Control towers do not automatically close VFR or DVFR flight plans since they do not know if a particular VFR aircraft is on a flight plan. If you fail to report or cancel your flight plan within 1/2 hour after your ETA, search and rescue procedures are started. REFERENCE− 14 CFR Section 91.153. 14 CFR Section 91.169. 5−1−15. Canceling IFR Flight Plan a. 14 CFR Sections 91.153 and 91.169 include the statement “When a flight plan has been activated, the pilot-in-command, upon canceling or completing the flight under the flight plan, must notify an FAA Flight Service Station or ATC facility.” b. An IFR flight plan may be canceled at any time the flight is operating in VFR conditions outside Class A airspace by pilots stating “CANCEL MY IFR FLIGHT PLAN” to the controller or air/ground station with which they are communicating. Immediately after canceling an IFR flight plan, a pilot should take the necessary action to change to the appropriate air/ground frequency, VFR radar beacon code and VFR altitude or flight level. c. ATC separation and information services will be discontinued, including radar services (where applicable). Consequently, if the canceling flight desires VFR radar advisory service, the pilot must specifically request it. NOTE− Pilots must be aware that other procedures may be applicable to a flight that cancels an IFR flight plan within an area where a special program, such as a designated Preflight 12/2/21 6/17/21 TRSA, Class C airspace, or Class B airspace, has been established. d. If a DVFR flight plan requirement exists, the pilot is responsible for filing this flight plan to replace the canceled IFR flight plan. If a subsequent IFR operation becomes necessary, a new IFR flight plan must be filed and an ATC clearance obtained before operating in IFR conditions. e. If operating on an IFR flight plan to an airport with a functioning control tower, the flight plan is automatically closed upon landing. f. If operating on an IFR flight plan to an airport where there is no functioning control tower, the pilot must initiate cancellation of the IFR flight plan. This can be done after landing if there is a functioning FSS or other means of direct communications with ATC. In the event there is no FSS and/or air/ground communications with ATC is not possible below a certain altitude, the pilot should, weather conditions permitting, cancel the IFR flight plan while still airborne and able to communicate with ATC by radio. This will not only save the time and expense of canceling the flight plan by telephone but will quickly release the airspace for use by other aircraft. 5−1−16. RNAV and RNP Operations a. During the pre−flight planning phase the availability of the navigation infrastructure required for the intended operation, including any non−RNAV contingencies, must be confirmed for the period of intended operation. Availability of the onboard navigation equipment necessary for the route to be flown must be confirmed. Pilots are reminded that on composite VFR to IFR flight plan, or on an IFR clearance, while flying unpublished departures via RNAV into uncontrolled airspace, the PIC is responsible for terrain and obstruction clearance until reaching the MEA/MIA/MVA/OROCA. AIM c. The onboard navigation database must be current and appropriate for the region of intended operation and must include the navigation aids, waypoints, and coded terminal airspace procedures for the departure, arrival and alternate airfields. d. During system initialization, pilots of aircraft equipped with a Flight Management System or other RNAV−certified system, must confirm that the navigation database is current, and verify that the aircraft position has been entered correctly. Flight crews should crosscheck the cleared flight plan against charts or other applicable resources, as well as the navigation system textual display and the aircraft map display. This process includes confirmation of the waypoints sequence, reasonableness of track angles and distances, any altitude or speed constraints, and identification of fly−by or fly−over waypoints. A procedure must not be used if validity of the navigation database is in doubt. e. Prior to commencing takeoff, the flight crew must verify that the RNAV system is operating correctly and the correct airport and runway data have been loaded. f. During the pre−flight planning phase RAIM prediction must be performed if TSO−C129() equipment is used to solely satisfy the RNAV and RNP requirement. GPS RAIM availability must be confirmed for the intended route of flight (route and time) using current GPS satellite information. In the event of a predicted, continuous loss of RAIM of more than five (5) minutes for any part of the intended flight, the flight should be delayed, canceled, or re−routed where RAIM requirements can be met. Operators may satisfy the predictive RAIM requirement through any one of the following methods: 1. Operators may monitor the status of each satellite in its plane/slot position, by accounting for the latest GPS constellation status (for example, NOTAMs or NANUs), and compute RAIM availability using model−specific RAIM prediction software; NOTE− OROCA is a published altitude which provides 1,000 feet of terrain and obstruction clearance in the U.S. (2,000 feet of clearance in designated mountainous areas). These altitudes are not assessed for NAVAID signal coverage, air traffic control surveillance, or communications coverage, and are published for general situational awareness, flight planning and in−flight contingency use. 2. Operators may use the Service Availability Prediction Tool (SAPT) on the FAA en route and terminal RAIM prediction website; b. If a pilot determines a specified RNP level cannot be achieved, revise the route or delay the operation until appropriate RNP level can be ensured. 4. Operators may use a third party interface, incorporating FAA/VOLPE RAIM prediction data without altering performance values, to predict Preflight 3. Operators may contact a Flight Service Station to obtain non−precision approach RAIM; 5−1−17 7110.65R CHG 2 AIM AIM RAIM outages for the aircraft’s predicted flight path and times; 5. Operators may use the receiver’s installed RAIM prediction capability (for TSO−C129a/Class A1/B1/C1 equipment) to provide non−precision approach RAIM, accounting for the latest GPS constellation status (for example, NOTAMs or NANUs). Receiver non−precision approach RAIM should be checked at airports spaced at intervals not to exceed 60 NM along the RNAV 1 procedure’s flight track. “Terminal” or “Approach” RAIM must be available at the ETA over each airport checked; or, 6. Operators not using model−specific software or FAA/VOLPE RAIM data will need FAA operational approval. NOTE− If TSO−C145/C146 equipment is used to satisfy the RNAV and RNP requirement, the pilot/operator need not perform the prediction if WAAS coverage is confirmed to be available along the entire route of flight. Outside the U.S. or in areas where WAAS coverage is not available, operators using TSO−C145/C146 receivers are required to check GPS RAIM availability. 5−1−17. Cold Temperature Operations a. Pilots should begin planning for cold temperature operations during the preflight planning phase. Cold temperatures produce barometric altimetry errors, which affect instrument flight procedures. Currently there are two temperature limitations that may be published in the notes box of the middle briefing strip on an instrument approach procedure (IAP). The two published temperature limitations are: 1. A temperature range limitation associated with the use of baro−VNAV that may be published on an United States PBN IAP titled RNAV (GPS) or RNAV (RNP); and/or 2. A Cold Temperature Airport (CTA) limitation designated by a snowflake ICON and temperature in Celsius (C) that is published on every IAP for the airfield. 5−1−18 3/15/07 12/2/21 6/17/21 b. Pilots should request the lowest forecast temperature +/− 1 hour for arrival and departure operations. If the temperature is forecast to be outside of the baro−VNAV or at or below the CTA temperature limitation, consider the following: 1. When using baro−VNAV with an aircraft that does not have an automated temperature compensating function, pilots should plan to use the appropriate minima and/or IAP. (a) The LNAV/VNAV line of minima on an RNAV (GPS) may not be used without an approved automated temperature compensating function if the temperature is outside of the baro−VNAV temperature range limitation. The LNAV minima may be used. (b) The RNAV (RNP) procedure may not be accomplished without an approved automated temperature compensating function if the temperature is outside of the baro−VNAV temperature range limitation. 2. If the temperature is forecast to be at or below the published CTA temperature, pilots should calculate a correction for the appropriate segment/s or a correction for all the segments if using the “All Segments Method.” Pilots should review the operating procedures for the aircraft’s temperature compensating system when planning to use the system for any cold temperature corrections. Any planned altitude correction for the intermediate and/or missed approach holding segments must be coordinated with ATC. Pilots do not have to advise ATC of a correction in the final segment. NOTE− The charted baro−VNAV temperature range limitation does not apply to pilots operating aircraft with an airworthiness approval to conduct an RNAV (GPS) approach to LNAV/VNAV minimums with the use of SBAS vertical guidance. REFERENCE− AIM, Chapter 7, Section 3, Cold Temperature Barometric Altimeter Errors, Setting Procedures, and Cold Temperature Airports (CTA). Preflight 6/17/21 AIM Section 2. Departure Procedures 5−2−1. Pre-taxi Clearance Procedures 2. Participating pilots call clearance delivery or ground control not more than 10 minutes before proposed taxi time. clearance via data link to participating airline/service provider computers for PDC. The airline/service provider will then deliver the clearance via the Aircraft Communications Addressing and Reporting System (ACARS) or a similar data link system, or for non-data link equipped aircraft, via a printer located at the departure gate. For CPDLC-DCL, the departure clearance is uplinked from the ATCT via the Future Air Navigation System (FANS) to the aircraft avionics and requires a response from the flight crew. Both PDC and CPDLC-DCL reduce frequency congestion, controller workload, and are intended to mitigate delivery/read back errors. 3. IFR clearance (or delay information, if clearance cannot be obtained) is issued at the time of this initial call-up. b. Both services are available only to participating aircraft that have subscribed to the service through an approved service provider. 4. When the IFR clearance is received on clearance delivery frequency, pilots call ground control when ready to taxi. c. In all situations, the pilot is encouraged to contact clearance delivery if a question or concern exists regarding an automated clearance. Due to technical reasons, the following limitations/differences exist between the two services: a. Certain airports have established pre-taxi clearance programs whereby pilots of departing instrument flight rules (IFR) aircraft may elect to receive their IFR clearances before they start taxiing for takeoff. The following provisions are included in such procedures: 1. Pilot participation is not mandatory. 5. Normally, pilots need not inform ground control that they have received IFR clearance on clearance delivery frequency. Certain locations may, however, require that the pilot inform ground control of a portion of the routing or that the IFR clearance has been received. 6. If a pilot cannot establish contact on clearance delivery frequency or has not received an IFR clearance before ready to taxi, the pilot should contact ground control and inform the controller accordingly. b. Locations where these procedures are in effect are indicated in the Chart Supplement U.S. 5−2−2. Automated Pre−Departure Clearance Procedures a. Many airports in the National Airspace System are equipped with the Terminal Data Link System (TDLS) that includes the Pre−Departure Clearance (PDC) and Controller Pilot Data Link Communication–Departure Clearance (CPDLC-DCL) functions. Both the PDC and CPDLC-DCL functions automate the Clearance Delivery operations in the ATCT for participating users. Both functions display IFR clearances from the ARTCC to the ATCT. The Clearance Delivery controller in the ATCT can append local departure information and transmit the Departure Procedures 1. PDC (a) Aircraft filing multiple flight plans are limited to one PDC clearance per departure airport within an 18−hour period. Additional clearances will be delivered verbally. (b) If the clearance is revised or modified prior to delivery, it will be rejected from PDC and the clearance will need to be delivered verbally. (c) No acknowledgment of receipt or read back is required for a PDC. 2. CPDLC−DCL (a) No limitation to the number of clearances received. (b) Allows delivery of revised flight data, including revised departure clearances. (c) A response from the flight crew is required. (d) Requires a logon to the FAA National Single Data Authority − KUSA − utilizing the ATC FANS application. (e) To be eligible, operators must have received CPDLC/FANS authorization from the 5−2−1 AIM responsible civil aviation authority, and file appropriate equipment information in ICAO field 10a and in the ICAO field 18 DAT (Other Data Applications) of the flight plan. 5−2−3. IFR Clearances Off Uncontrolled Airports a. Pilots departing on an IFR flight plan should consult the Chart Supplement U.S. to determine the frequency or telephone number to use to contact clearance delivery. On initial contact, pilots should advise that the flight is IFR and state the departure and destination airports. b. Air traffic facilities providing clearance delivery services via telephone will have their telephone number published in the Chart Supplement U.S. of that airport’s entry. This same section may also contain a telephone number to use for cancellation of an IFR flight plan after landing. c. Except in Alaska, pilots of MEDEVAC flights may obtain a clearance by calling 1−877−543−4733. 5−2−4. Taxi Clearance Pilots on IFR flight plans should communicate with the control tower on the appropriate ground control or clearance delivery frequency prior to starting engines, to receive engine start time, taxi, and/or clearance information. 5−2−5. Line Up and Wait (LUAW) a. Line up and wait is an air traffic control (ATC) procedure designed to position an aircraft onto the runway for an imminent departure. The ATC instruction “LINE UP AND WAIT” is used to instruct a pilot to taxi onto the departure runway and line up and wait. EXAMPLE− Tower: “N234AR Runway 24L, line up and wait.” b. This ATC instruction is not an authorization to takeoff. In instances where the pilot has been instructed to line up and wait and has been advised of a reason/condition (wake turbulence, traffic on an intersecting runway, etc.) or the reason/condition is clearly visible (another aircraft that has landed on or is taking off on the same runway), and the reason/condition is satisfied, the pilot should expect 5−2−2 6/17/21 an imminent takeoff clearance, unless advised of a delay. If you are uncertain about any ATC instruction or clearance, contact ATC immediately. c. If a takeoff clearance is not received within a reasonable amount of time after clearance to line up and wait, ATC should be contacted. EXAMPLE− Aircraft: Cessna 234AR holding in position Runway 24L. Aircraft: Cessna 234AR holding in position Runway 24L at Bravo. NOTE− FAA analysis of accidents and incidents involving aircraft holding in position indicate that two minutes or more elapsed between the time the instruction was issued to line up and wait and the resulting event (for example, land−over or go−around). Pilots should consider the length of time that they have been holding in position whenever they HAVE NOT been advised of any expected delay to determine when it is appropriate to query the controller. REFERENCE− Advisory Circulars 91−73A, Part 91 and Part 135 Single−Pilot Procedures during Taxi Operations, and 120−74A, Parts 91, 121, 125, and 135 Flightcrew Procedures during Taxi Operations d. Situational awareness during line up and wait operations is enhanced by monitoring ATC instructions/clearances issued to other aircraft. Pilots should listen carefully if another aircraft is on frequency that has a similar call sign and pay close attention to communications between ATC and other aircraft. If you are uncertain of an ATC instruction or clearance, query ATC immediately. Care should be taken to not inadvertently execute a clearance/ instruction for another aircraft. e. Pilots should be especially vigilant when conducting line up and wait operations at night or during reduced visibility conditions. They should scan the full length of the runway and look for aircraft on final approach or landing roll out when taxiing onto a runway. ATC should be contacted anytime there is a concern about a potential conflict. f. When two or more runways are active, aircraft may be instructed to “LINE UP AND WAIT” on two or more runways. When multiple runway operations are being conducted, it is important to listen closely for your call sign and runway. Be alert for similar sounding call signs and acknowledge all instructions with your call sign. When you are holding in position and are not sure if the takeoff clearance was for you, ask ATC before you begin takeoff roll. ATC prefers Departure Procedures 6/17/21 that you confirm a takeoff clearance rather than mistake another aircraft’s clearance for your own. g. When ATC issues intersection “line up and wait” and takeoff clearances, the intersection designator will be used. If ATC omits the intersection designator, call ATC for clarification. AIM 1. The aircraft is on the ground or it has departed visual flight rules (VFR) and the pilot is requesting IFR clearance while airborne. 2. That a pilot will not accept an abbreviated clearance if the route or destination of a flight plan filed with ATC has been changed by the pilot or the company or the operations officer before departure. EXAMPLE− Aircraft: “Cherokee 234AR, Runway 24L at November 4, line up and wait.” 3. That it is the responsibility of the company or operations office to inform the pilot when they make a change to the filed flight plan. h. If landing traffic is a factor during line up and wait operations, ATC will inform the aircraft in position of the closest traffic within 6 flying miles requesting a full−stop, touch−and−go, stop−and−go, or an unrestricted low approach to the same runway. Pilots should take care to note the position of landing traffic. ATC will also advise the landing traffic when an aircraft is authorized to “line up and wait” on the same runway. 4. That it is the responsibility of the pilot to inform ATC in the initial call-up (for clearance) when the filed flight plan has been either: EXAMPLE− Tower: “Cessna 234AR, Runway 24L, line up and wait. Traffic a Boeing 737, six mile final.” Tower: “Delta 1011, continue, traffic a Cessna 210 holding in position Runway 24L.” NOTE− ATC will normally withhold landing clearance to arrival aircraft when another aircraft is in position and holding on the runway. i. Never land on a runway that is occupied by another aircraft, even if a landing clearance was issued. Do not hesitate to ask the controller about the traffic on the runway and be prepared to execute a go−around. NOTE− Always clarify any misunderstanding or confusion concerning ATC instructions or clearances. ATC should be advised immediately if there is any uncertainty about the ability to comply with any of their instructions. 5−2−6. Abbreviated IFR Departure Clearance (Cleared. . .as Filed) Procedures a. ATC facilities will issue an abbreviated IFR departure clearance based on the ROUTE of flight filed in the IFR flight plan, provided the filed route can be approved with little or no revision. These abbreviated clearance procedures are based on the following conditions: Departure Procedures (a) Amended, or (b) Canceled and replaced with a new filed flight plan. NOTE− The facility issuing a clearance may not have received the revised route or the revised flight plan by the time a pilot requests clearance. b. Controllers will issue a detailed clearance when they know that the original filed flight plan has been changed or when the pilot requests a full route clearance. c. The clearance as issued will include the destination airport filed in the flight plan. d. ATC procedures now require the controller to state the DP name, the current number and the DP transition name after the phrase “Cleared to (destination) airport” and prior to the phrase, “then as filed,” for ALL departure clearances when the DP or DP transition is to be flown. The procedures apply whether or not the DP is filed in the flight plan. e. STARs, when filed in a flight plan, are considered a part of the filed route of flight and will not normally be stated in an initial departure clearance. If the ARTCC’s jurisdictional airspace includes both the departure airport and the fix where a STAR or STAR transition begins, the STAR name, the current number and the STAR transition name MAY be stated in the initial clearance. f. “Cleared to (destination) airport as filed” does NOT include the en route altitude filed in a flight plan. An en route altitude will be stated in the clearance or the pilot will be advised to expect an assigned or filed altitude within a given time frame or at a certain point after departure. This may be done verbally in the departure instructions or stated in the DP. 5−2−3 7110.65R CHG 2 AIM AIM g. In both radar and nonradar environments, the controller will state “Cleared to (destination) airport as filed” or: 1. If a DP or DP transition is to be flown, specify the DP name, the current DP number, the DP transition name, the assigned altitude/flight level, and any additional instructions (departure control frequency, beacon code assignment, etc.) necessary to clear a departing aircraft via the DP or DP transition and the route filed. 3/15/07 12/2/21 6/17/21 EXAMPLE− “Washington clearance delivery (or ground control if appropriate) American Seventy Six at gate one, IFR Los Angeles.” 3. If the flight plan has been changed, state the change and request a full route clearance. EXAMPLE− “Washington clearance delivery, American Seventy Six at gate one. IFR San Francisco. My flight plan route has been amended (or destination changed). Request full route clearance.” EXAMPLE− National Seven Twenty cleared to Miami Airport Intercontinental one departure, Lake Charles transition then as filed, maintain Flight Level two seven zero. 4. Request verification or clarification from ATC if ANY portion of the clearance is not clearly understood. 2. When there is no DP or when the pilot cannot accept a DP, the controller will specify the assigned altitude or flight level, and any additional instructions necessary to clear a departing aircraft via an appropriate departure routing and the route filed. 5. When requesting clearance for the IFR portion of a VFR/IFR flight, request such clearance prior to the fix where IFR operation is proposed to commence in sufficient time to avoid delay. Use the following phraseology: NOTE− A detailed departure route description or a radar vector may be used to achieve the desired departure routing. 3. If it is necessary to make a minor revision to the filed route, the controller will specify the assigned DP or DP transition (or departure routing), the revision to the filed route, the assigned altitude or flight level and any additional instructions necessary to clear a departing aircraft. EXAMPLE− Jet Star One Four Two Four cleared to Atlanta Airport, South Boston two departure then as filed except change route to read South Boston Victor 20 Greensboro, maintain one seven thousand. 4. Additionally, in a nonradar environment, the controller will specify one or more fixes, as necessary, to identify the initial route of flight. EXAMPLE− Cessna Three One Six Zero Foxtrot cleared to Charlotte Airport as filed via Brooke, maintain seven thousand. h. To ensure success of the program, pilots should: 1. Avoid making changes to a filed flight plan just prior to departure. 2. State the following information in the initial call-up to the facility when no change has been made to the filed flight plan: Aircraft call sign, location, type operation (IFR) and the name of the airport (or fix) to which you expect clearance. 5−2−4 EXAMPLE− “Los Angeles center, Apache Six One Papa, VFR estimating Paso Robles VOR at three two, one thousand five hundred, request IFR to Bakersfield.” 5−2−7. Departure Restrictions, Clearance Void Times, Hold for Release, and Release Times a. ATC may assign departure restrictions, clearance void times, hold for release, and release times, when necessary, to separate departures from other traffic or to restrict or regulate the departure flow. Departures from an airport without an operating control tower must be issued either a departure release (along with a release time and/or void time if applicable), or a hold for release. REFERENCE− FAA Order JO 7110.65, Para 4−3−4, Departure Release, Hold for Release, Release Times, Departure Restrictions, and Clearance Void Times. 1. Clearance Void Times. A pilot may receive a clearance, when operating from an airport without a control tower, which contains a provision for the clearance to be void if not airborne by a specific time. A pilot who does not depart prior to the clearance void time must advise ATC as soon as possible of their intentions. ATC will normally advise the pilot of the time allotted to notify ATC that the aircraft did not depart prior to the clearance void time. This time cannot exceed 30 minutes. Failure of an aircraft to contact ATC within 30 minutes after the clearance Departure Procedures 12/2/21 6/17/21 AIM void time will result in the aircraft being considered overdue and search and rescue procedures initiated. traffic management procedures and/or to separate a departing aircraft from other traffic. NOTE− 1. Other IFR traffic for the airport where the clearance is issued is suspended until the aircraft has contacted ATC or until 30 minutes after the clearance void time or 30 minutes after the clearance release time if no clearance void time is issued. EXAMPLE− (Aircraft identification) released for departure at (time in hours and/or minutes). 2. If the clearance void time expires, it does not cancel the departure clearance or IFR flight plan. It withdraws the pilot’s authority to depart IFR until a new departure release/release time has been issued by ATC and is acknowledged by the pilot. 3. Pilots who depart at or after their clearance void time are not afforded IFR separation and may be in violation of 14 CFR Section 91.173 which requires that pilots receive an appropriate ATC clearance before operating IFR in controlled airspace. 4. Pilots who choose to depart VFR after their clearance void time has expired should not depart using the previously assigned IFR transponder code. EXAMPLE− Clearance void if not off by (clearance void time) and, if required, if not off by (clearance void time) advise (facility) not later than (time) of intentions. 2. Hold for Release. ATC may issue “hold for release” instructions in a clearance to delay an aircraft’s departure for traffic management reasons (i.e., weather, traffic volume, etc.). When ATC states in the clearance, “hold for release,” the pilot may not depart utilizing that IFR clearance until a release time or additional instructions are issued by ATC. In addition, ATC will include departure delay information in conjunction with “hold for release” instructions. The ATC instruction, “hold for release,” applies to the IFR clearance and does not prevent the pilot from departing under VFR. However, prior to takeoff the pilot should cancel the IFR flight plan and operate the transponder/ADS−B on the appropriate VFR code. An IFR clearance may not be available after departure. EXAMPLE− (Aircraft identification) cleared to (destination) airport as filed, maintain (altitude), and, if required (additional instructions or information), hold for release, expect (time in hours and/or minutes) departure delay. 3. Release Times. A “release time” is a departure restriction issued to a pilot by ATC, specifying the earliest time an aircraft may depart. ATC will use “release times” in conjunction with Departure Procedures 4. Expect Departure Clearance Time (EDCT). The EDCT is the runway release time assigned to an aircraft included in traffic management programs. Aircraft are expected to depart no earlier than 5 minutes before, and no later than 5 minutes after the EDCT. b. If practical, pilots departing uncontrolled airports should obtain IFR clearances prior to becoming airborne when two-way communications with the controlling ATC facility is available. 5−2−8. Departure Control a. Departure Control is an approach control function responsible for ensuring separation between departures. So as to expedite the handling of departures, Departure Control may suggest a takeoff direction other than that which may normally have been used under VFR handling. Many times it is preferred to offer the pilot a runway that will require the fewest turns after takeoff to place the pilot on course or selected departure route as quickly as possible. At many locations particular attention is paid to the use of preferential runways for local noise abatement programs, and route departures away from congested areas. b. Departure Control utilizing radar will normally clear aircraft out of the terminal area using vectors, a diverse vector area (DVA), or published DPs. 1. When a departure is to be vectored immediately following takeoff using vectors, a DVA, or published DPs that begins with an ATC assigned heading off the ground, the pilot will be advised prior to takeoff of the initial heading to be flown but may not be advised of the purpose of the heading. When ATC assigns an initial heading with the takeoff clearance that will take the aircraft off an assigned procedure (for example, an RNAV SID with a published lateral path to a waypoint and crossing restrictions from the departure end of runway), the controller will assign an altitude to maintain with the initial heading and, if necessary, a speed to maintain. 2. At some airports when a departure will fly an RNAV SID that begins at the runway, ATC may advise aircraft of the initial fix/waypoint on the 5−2−5 7110.65R CHG 2 AIM AIM RNAV route. The purpose of the advisory is to remind pilots to verify the correct procedure is programmed in the FMS before takeoff. Pilots must immediately advise ATC if a different RNAV SID is entered in the aircraft’s FMC. When this advisory is absent, pilots are still required to fly the assigned SID as published. EXAMPLE− Delta 345 RNAV to MPASS, Runway26L, cleared for takeoff. NOTE− 1. The SID transition is not restated as it is contained in the ATC clearance. 2. Aircraft cleared via RNAV SIDs designed to begin with a vector to the initial waypoint are assigned a heading before departure. 3. Pilots operating in a radar environment are expected to associate departure headings or an RNAV departure advisory with vectors or the flight path to their planned route or flight. When given a vector taking the aircraft off a previously assigned nonradar route, the pilot will be advised briefly what the vector is to achieve. Thereafter, radar service will be provided until the aircraft has been reestablished “on-course” using an appropriate navigation aid and the pilot has been advised of the aircraft’s position or a handoff is made to another radar controller with further surveillance capabilities. c. Controllers will inform pilots of the departure control frequencies and, if appropriate, the transponder code before takeoff. Pilots must ensure their transponder/ADS−B is adjusted to the “on” or normal operating position as soon as practical and remain on during all operations unless otherwise requested to change to “standby” by ATC. Pilots should not change to the departure control frequency until requested. Controllers may omit the departure control frequency if a DP has or will be assigned and the departure control frequency is published on the DP. 5−2−9. Instrument Departure Procedures (DP) − Obstacle Departure Procedures (ODP), Standard Instrument Departures (SID), and Diverse Vector Areas (DVA) a. Instrument departure procedures are preplanned instrument flight rule (IFR) procedures which provide obstruction clearance from the terminal area to the appropriate en route structure. There are two types of DPs, Obstacle Departure Procedures (ODP), printed either textually or 5−2−6 3/15/07 12/2/21 6/17/21 graphically, and Standard Instrument Departures (SID), always printed graphically. All DPs, either textual or graphic may be designed using either conventional or RNAV criteria. RNAV procedures will have RNAV printed in the title; for example, SHEAD TWO DEPARTURE (RNAV). ODPs provide obstruction clearance via the least onerous route from the terminal area to the appropriate en route structure. ODPs are recommended for obstruction clearance and may be flown without ATC clearance unless an alternate departure procedure (SID or radar vector) has been specifically assigned by ATC. Graphic ODPs will have (OBSTACLE) printed in the procedure title; for example, GEYSR THREE DEPARTURE (OBSTACLE), or, CROWN ONE DEPARTURE (RNAV) (OBSTACLE). Standard Instrument Departures are air traffic control (ATC) procedures printed for pilot/controller use in graphic form to provide obstruction clearance and a transition from the terminal area to the appropriate en route structure. SIDs are primarily designed for system enhancement and to reduce pilot/controller workload. ATC clearance must be received prior to flying a SID. All DPs provide the pilot with a way to depart the airport and transition to the en route structure safely. b. A Diverse Vector Area (DVA) is an area in which ATC may provide random radar vectors during an uninterrupted climb from the departure runway until above the MVA/MIA, established in accordance with the TERPS criteria for diverse departures. The DVA provides obstacle and terrain avoidance in lieu of taking off from the runway under IFR using an ODP or SID. c. Pilots operating under 14 CFR Part 91 are strongly encouraged to file and fly a DP at night, during marginal Visual Meteorological Conditions (VMC) and Instrument Meteorological Conditions (IMC), when one is available. The following paragraphs will provide an overview of the DP program, why DPs are developed, what criteria are used, where to find them, how they are to be flown, and finally pilot and ATC responsibilities. d. Why are DPs necessary? The primary reason is to provide obstacle clearance protection information to pilots. A secondary reason, at busier airports, is to increase efficiency and reduce communications and departure delays through the use of SIDs. When an instrument approach is initially developed for an airport, the need for DPs is assessed. The procedure Departure Procedures 12/2/21 6/17/21 designer conducts an obstacle analysis to support departure operations. If an aircraft may turn in any direction from a runway within the limits of the assessment area (see paragraph 5−2−9e3) and remain clear of obstacles, that runway passes what is called a diverse departure assessment and no ODP will be published. A SID may be published if needed for air traffic control purposes. However, if an obstacle penetrates what is called the 40:1 obstacle identification surface, then the procedure designer chooses whether to: 1. Establish a steeper than normal climb gradient; or 2. Establish a steeper than normal climb gradient with an alternative that increases takeoff minima to allow the pilot to visually remain clear of the obstacle(s); or or 3. Design and publish a specific departure route; 4. A combination or all of the above. e. What criteria is used to provide obstruction clearance during departure? 1. Unless specified otherwise, required obstacle clearance for all departures, including diverse, is based on the pilot crossing the departure end of the runway at least 35 feet above the departure end of runway elevation, climbing to 400 feet above the departure end of runway elevation before making the initial turn, and maintaining a minimum climb gradient of 200 feet per nautical mile (FPNM), unless required to level off by a crossing restriction, until the minimum IFR altitude. A greater climb gradient may be specified in the DP to clear obstacles or to achieve an ATC crossing restriction. If an initial turn higher than 400 feet above the departure end of runway elevation is specified in the DP, the turn should be commenced at the higher altitude. If a turn is specified at a fix, the turn must be made at that fix. Fixes may have minimum and/or maximum crossing altitudes that must be adhered to prior to passing the fix. In rare instances, obstacles that exist on the extended runway centerline may make an “early turn” more desirable than proceeding straight ahead. In these cases, the published departure instructions will include the language “turn left(right) as soon as practicable.” These departures will also include a ceiling and visibility minimum of at least 300 and 1. Pilots encountering one of these DPs should preplan Departure Procedures AIM the climb out to gain altitude and begin the turn as quickly as possible within the bounds of safe operating practices and operating limitations. This type of departure procedure is being phased out. NOTE− “Practical” or “feasible” may exist in some existing departure text instead of “practicable.” 2. ODPs, SIDs, and DVAs assume normal aircraft performance, and that all engines are operating. Development of contingency procedures, required to cover the case of an engine failure or other emergency in flight that may occur after liftoff, is the responsibility of the operator. (More detailed information on this subject is available in Advisory Circular AC 120−91, Airport Obstacle Analysis, and in the “Departure Procedures” section of chapter 2 in the Instrument Procedures Handbook, FAA−H−8083−16.) 3. The 40:1 obstacle identification surface (OIS) begins at the departure end of runway (DER) and slopes upward at 152 FPNM until reaching the minimum IFR altitude or entering the en route structure. This assessment area is limited to 25 NM from the airport in nonmountainous areas and 46 NM in designated mountainous areas. Beyond this distance, the pilot is responsible for obstacle clearance if not operating on a published route, if below (having not reached) the MEA or MOCA of a published route, or an ATC assigned altitude. See FIG 5−2−1. (Ref 14 CFR 91.177 for further information on en route altitudes.) NOTE− ODPs are normally designed to terminate within these distance limitations, however, some ODPs will contain routes that may exceed 25/46 NM; these routes will ensure obstacle protection until reaching the end of the ODP. 4. Obstacles that are located within 1 NM of the DER and penetrate the 40:1 OCS are referred to as “low, close−in obstacles.” The standard required obstacle clearance (ROC) of 48 feet per NM to clear these obstacles would require a climb gradient greater than 200 feet per NM for a very short distance, only until the aircraft was 200 feet above the DER. To eliminate publishing an excessive climb gradient, the obstacle AGL/MSL height and location relative to the DER is noted in the “Take−off Minimums and (OBSTACLE) Departure Procedures” section of a given Terminal Procedures Publication (TPP) booklet. (a) Pilots must refer to the TPP booklet or the Graphic ODP for information on these obstacles. 5−2−7 7110.65R CHG 2 AIM AIM 3/15/07 12/2/21 6/17/21 These obstacle notes will no longer be published on SIDs. Pilots assigned a SID for departure must refer to the airport entry in the TPP to obtain information on these obstacles. (b) The purpose of noting obstacles in the “Take−off Minimums and (OBSTACLE) Departure Procedures” section of the TPP is to identify the obstacle(s) and alert the pilot to the height and location of the obstacle(s) so they can be avoided. This can be accomplished in a variety of ways; for example, the pilot may be able to see the obstruction and maneuver around the obstacle(s) if necessary; early liftoff/climb performance may allow the aircraft to cross well above the obstacle(s); or if the obstacle(s) cannot be visually acquired during departure, preflight planning should take into account what turns or other maneuvers may be necessary immediately after takeoff to avoid the obstruction(s). FIG 5−2−1 Diverse Departure Obstacle Assessment to 25/46 NM EXAMPLE− TAKEOFF OBSTACLE NOTES: Rwy 14, trees 2011’ from DER, 29’ left of centerline, 100’ AGL/3829’ MSL. Rwy 32, trees 1009’ from DER, 697’ left of centerline, 100’ AGL/3839’ MSL. Tower 4448’ from DER, 1036’ left of centerline, 165’ AGL/3886’ MSL. NOTE− Compliance with 14 CFR Part 121 or 135 one−engine−inoperative (OEI) departure performance requirements, or similar ICAO/State rules, cannot be assured by the sole use of “low, close−in” obstacle data as published in the TPP. Operators should refer to precise data sources (for example, GIS database, etc.) specifically intended for OEI departure planning for those operations. 5. Climb gradients greater than 200 FPNM are specified when required to support procedure design constraints, obstacle clearance, and/or airspace restrictions. Compliance with a climb gradient for these purposes is mandatory when the procedure is part of the ATC clearance, unless increased takeoff minimums are provided and weather conditions allow compliance with these minimums. 5−2−8 NOTE− Climb gradients for ATC purposes are being phased out on SIDs. EXAMPLE− “Cross ALPHA intersection at or below 4000; maintain 6000.” The pilot climbs at least 200 FPNM to 6000. If 4000 is reached before ALPHA, the pilot levels off at 4000 until passing ALPHA; then immediately resumes at least 200 FPNM climb. EXAMPLE− “TAKEOFF MINIMUMS: RWY 27, Standard with a minimum climb of 280’ per NM to 2500.” A climb of at least 280 FPNM is required to 2500 and is mandatory when the departure procedure is included in the ATC clearance. NOTE− Some SIDs still retain labeled “ATC” climb gradients published or have climb gradients that are established to meet a published altitude restriction that is not required for obstacle clearance or procedure design criteria. These procedures will be revised in the course of the normal procedure amendment process. Departure Procedures 12/2/21 6/17/21 6. Climb gradients may be specified only to an altitude/fix, above which the normal gradient applies. An ATC−required altitude restriction published at a fix, will not have an associated climb gradient published with that restriction. Pilots are expected to determine if crossing altitudes can be met, based on the performance capability of the aircraft they are operating. EXAMPLE− “Minimum climb 340 FPNM to ALPHA.” The pilot climbs at least 340 FPNM to ALPHA, then at least 200 FPNM to MIA. 7. A Visual Climb Over Airport (VCOA) procedure is a departure option for an IFR aircraft, operating in visual meteorological conditions equal to or greater than the specified visibility and ceiling, to visually conduct climbing turns over the airport to the published “at or above” altitude. At this point, the pilot may proceed in instrument meteorological conditions to the first en route fix using a diverse departure, or to proceed via a published routing to a fix from where the aircraft may join the IFR en route structure, while maintaining a climb gradient of at least 200 feet per nautical mile. VCOA procedures are developed to avoid obstacles greater than 3 statute miles from the departure end of the runway as an alternative to complying with climb gradients greater than 200 feet per nautical mile. Pilots are responsible to advise ATC as early as possible of the intent to fly the VCOA option prior to departure. Pilots are expected to remain within the distance prescribed in the published visibility minimums during the climb over the airport until reaching the “at or above” altitude for the VCOA procedure. If no additional routing is published, then the pilot may proceed in accordance with their IFR clearance. If additional routing is published after the “at−or−above” altitude, the pilot must comply with the route to a fix that may include a climb−in−holding pattern to reach the MEA/MIA for the en route portion of their IFR flight. These textual procedures are published in the Take−Off Minimums and (Obstacle) Departure Procedures section of the Terminal Procedures Publications and/or appear as an option on a Graphic ODP. EXAMPLE− TAKEOFF MINIMUMS: Rwy 32, standard with minimum climb of 410’ per NM to 3000’ or 1100−3 for VCOA. Departure Procedures AIM VCOA: Rwy 32, obtain ATC approval for VCOA when requesting IFR clearance. Climb in visual conditions to cross Broken Bow Muni/Keith Glaze Field at or above 3500’ before proceeding on course. f. Who is responsible for obstacle clearance? DPs are designed so that adherence to the procedure by the pilot will ensure obstacle protection. Additionally: 1. Obstacle clearance responsibility also rests with the pilot when he/she chooses to climb in visual conditions in lieu of flying a DP and/or depart under increased takeoff minima rather than fly the climb gradient. Standard takeoff minima are one statute mile for aircraft having two engines or less and one−half statute mile for aircraft having more than two engines. Specified ceiling and visibility minima will allow visual avoidance of obstacles during the initial climb at the standard climb gradient. When departing using the VCOA, obstacle avoidance is not guaranteed if the pilot maneuvers farther from the airport than the published visibility minimum for the VCOA prior to reaching the published VCOA altitude. DPs may also contain what are called Low Close in Obstacles. These obstacles are less than 200 feet above the departure end of runway elevation and within one NM of the runway end and do not require increased takeoff minimums. These obstacles are identified on the SID chart or in the Take−off Minimums and (Obstacle) Departure Procedures section of the U. S. Terminal Procedure booklet. These obstacles are especially critical to aircraft that do not lift off until close to the departure end of the runway or which climb at the minimum rate. Pilots should also consider drift following lift−off to ensure sufficient clearance from these obstacles. That segment of the procedure that requires the pilot to see and avoid obstacles ends when the aircraft crosses the specified point at the required altitude. In all cases continued obstacle clearance is based on having climbed a minimum of 200 feet per nautical mile to the specified point and then continuing to climb at least 200 foot per nautical mile during the departure until reaching the minimum en route altitude unless specified otherwise. 2. ATC may vector the aircraft beginning with an ATC−assigned heading issued with the initial or takeoff clearance followed by subsequent vectors, if required, until reaching the minimum vectoring altitude by using a published Diverse Vector Area (DVA). 5−2−9 7110.65R CHG 2 AIM AIM 3. The DVA may be established below the Minimum Vectoring Altitude (MVA) or Minimum IFR Altitude (MIA) in a radar environment at the request of Air Traffic. This type of DP meets the TERPS criteria for diverse departures, obstacles, and terrain avoidance in which vectors below the MVA/MIA may be issued to departing aircraft. The DVA has been assessed for departures which do not follow a specific ground track, but will remain within the specified area. Use of a DVA is valid only when aircraft are permitted to climb uninterrupted from the departure runway to the MVA/MIA (or higher). ATC will not assign an altitude below the MVA/MIA within a DVA. At locations that have a DVA, ATC is not permitted to utilize a SID and DVA concurrently. (a) The existence of a DVA will be noted in the Takeoff Minimums and Obstacle Departure Procedure section of the U.S. Terminal Procedures Publication (TPP). The Takeoff Departure procedure will be listed first, followed by any applicable DVA. EXAMPLE− DIVERSE VECTOR AREA (RADAR VECTORS) AMDT 1 14289 (FAA) Rwy 6R, headings as assigned by ATC; requires minimum climb of 290’ per NM to 400. Rwys 6L, 7L, 7R, 24R, 25R, headings as assigned by ATC. (b) Pilots should be aware that a published climb gradient greater than the standard 200 FPNM can exist within a DVA. Pilots should note that the DVA has been assessed for departures which do not follow a specific ground track. (c) ATC may also vector an aircraft off a previously assigned DP. If the aircraft is airborne and established on a SID or ODP and subsequently vectored off, ATC is responsible for terrain and obstruction clearance. In all cases, the minimum 200 FPNM climb gradient is assumed. NOTE− As is always the case, when used by the controller during departure, the term “radar contact” should not be interpreted as relieving pilots of their responsibility to maintain appropriate terrain and obstruction clearance, which may include flying the obstacle DP. 4. Pilots must preplan to determine if the aircraft can meet the climb gradient (expressed in feet per nautical mile) required by the departure procedure or DVA, and be aware that flying at a higher than anticipated ground speed increases the climb rate 5−2−10 3/15/07 12/2/21 6/17/21 requirement in feet per minute. Higher than standard climb gradients are specified by a note on the departure procedure chart for graphic DPs, or in the Take−Off Minimums and (Obstacle) Departure Procedures section of the U.S. Terminal Procedures booklet for textual ODPs. The required climb gradient, or higher, must be maintained to the specified altitude or fix, then the standard climb gradient of 200 ft/NM can be resumed. A table for the conversion of climb gradient (feet per nautical mile) to climb rate (feet per minute), at a given ground speed, is included on the inside of the back cover of the U.S. Terminal Procedures booklets. g. Where are DPs located? DPs and DVAs will be listed by airport in the IFR Takeoff Minimums and (Obstacle) Departure Procedures Section, Section L, of the Terminal Procedures Publications (TPP). If the DP is textual, it will be described in TPP Section L. SIDs and complex ODPs will be published graphically and named. The name will be listed by airport name and runway in Section L. Graphic ODPs will also have the term “(OBSTACLE)” printed in the charted procedure title, differentiating them from SIDs. 1. An ODP that has been developed solely for obstacle avoidance will be indicated with the symbol “T” on appropriate Instrument Approach Procedure (IAP) charts and DP charts for that airport. The “T” symbol will continue to refer users to TPP Section C. In the case of a graphic ODP, the TPP Section C will only contain the name of the ODP. Since there may be both a textual and a graphic DP, Section C should still be checked for additional information. The nonstandard takeoff minimums and minimum climb gradients found in TPP Section C also apply to charted DPs and radar vector departures unless different minimums are specified on the charted DP. Takeoff minimums and departure procedures apply to all runways unless otherwise specified. New graphic DPs will have all the information printed on the graphic depiction. As a general rule, ATC will only assign an ODP from a non−towered airport when compliance with the ODP is necessary for aircraft to aircraft separation. Pilots may use the ODP to help ensure separation from terrain and obstacles. h. Responsibilities 1. Each pilot, prior to departing an airport on an IFR flight should: Departure Procedures 12/2/21 6/17/21 (a) Consider the type of terrain and other obstacles on or in the vicinity of the departure airport; (b) Determine whether an ODP is available; (c) Determine if obstacle avoidance can be maintained visually or if the ODP should be flown; and (d) Consider the effect of degraded climb performance and the actions to take in the event of an engine loss during the departure. Pilots should notify ATC as soon as possible of reduced climb capability in that circumstance. NOTE− Guidance concerning contingency procedures that address an engine failure on takeoff after V1 speed on a large or turbine−powered transport category airplane may be found in AC 120−91, Airport Obstacle Analysis. (e) Determine if a DVA is published and whether the aircraft is capable of meeting the published climb gradient. Advise ATC when requesting the IFR clearance, or as soon as possible, if unable to meet the DVA climb gradient. (f) Check for Takeoff Obstacle Notes published in the TPP for the takeoff runway. 2. Pilots should not exceed a published speed restriction associated with a SID waypoint until passing that waypoint. 3. After an aircraft is established on a SID and subsequently vectored or cleared to deviate off of the SID or SID transition, pilots must consider the SID canceled, unless the controller adds “expect to resume SID;” pilots should then be prepared to rejoin the SID at a subsequent fix or procedure leg. If the SID contains published altitude and/or speed restrictions, those restrictions are canceled and pilots will receive an altitude to maintain and, if necessary, a speed. ATC may also interrupt the vertical navigation of a SID and provide alternate altitude instructions while the aircraft remains established on the published lateral path. Aircraft may be vectored off of an ODP, or issued an altitude lower than a published altitude on an ODP, at which time the ODP is canceled. In these cases, ATC assumes responsibility for terrain and obstacle clearance. In all cases, the minimum 200 FPNM climb gradient is assumed. 4. Aircraft instructed to resume a SID procedure such as a DP or SID which contains speed and/or altitude restrictions, must be: Departure Procedures AIM or (a) Issued/reissued all applicable restrictions, (b) Advised to “Climb via SID” or resume published speed. EXAMPLE− “Resume the Solar One departure, Climb via SID.” “Proceed direct CIROS, resume the Solar One departure, Climb via SID.” 5. A clearance for a SID which does not contain published crossing restrictions, and/or is a SID with a Radar Vector segment or a Radar Vector SID, will be issued using the phraseology “Maintain (altitude).” 6. A clearance for a SID which contains published altitude restrictions may be issued using the phraseology “climb via.” Climb via is an abbreviated clearance that requires compliance with the procedure lateral path, associated speed and altitude restrictions along the cleared route or procedure. Clearance to “climb via” authorizes the pilot to: (a) When used in the IFR departure clearance, in a PDC, DCL or when cleared to a waypoint depicted on a SID, to join the procedure after departure or to resume the procedure. (b) When vertical navigation is interrupted and an altitude is assigned to maintain which is not contained on the published procedure, to climb from that previously-assigned altitude at pilot’s discretion to the altitude depicted for the next waypoint. (c) Once established on the depicted departure, to navigate laterally and climb to meet all published or assigned altitude and speed restrictions. NOTE− 1. When otherwise cleared along a route or procedure that contains published speed restrictions, the pilot must comply with those speed restrictions independent of a climb via clearance. 2. ATC anticipates pilots will begin adjusting speed the minimum distance necessary prior to a published speed restriction so as to cross the waypoint/fix at the published speed. Once at the published speed ATC expects pilots will maintain the published speed until additional adjustment is required to comply with further published or ATC assigned speed restrictions or as required to ensure compliance with 14 CFR Section 91.117. 3. If ATC interrupts lateral/vertical navigation while an aircraft is flying a SID, ATC must ensure obstacle clearance. When issuing a “climb via” clearance to join or 5−2−11 7110.65R CHG 2 AIM AIM resume a procedure ATC must ensure obstacle clearance until the aircraft is established on the lateral and vertical path of the SID. 4. ATC will assign an altitude to cross if no altitude is depicted at a waypoint/fix or when otherwise necessary/ required, for an aircraft on a direct route to a waypoint/fix where the SID will be joined or resumed. 5. SIDs will have a “top altitude;” the “top altitude” is the charted “maintain” altitude contained in the procedure description or assigned by ATC. REFERENCE− FAA Order JO 7110.65, Paragraph 5-6-2, Methods PCG, Climb Via, Top Altitude EXAMPLE− 1. Lateral route clearance: “Cleared Loop Six departure.” NOTE− The aircraft must comply with the SID lateral path, and any published speed restrictions. 2. Routing with assigned altitude: “Cleared Loop Six departure, climb and maintain four thousand.” NOTE− The aircraft must comply with the SID lateral path, and any published speed restriction while climbing unrestricted to four thousand. 3. (A pilot filed a flight plan to the Johnston Airport using the Scott One departure, Jonez transition, then Q-145. The pilot filed for FL350. The Scott One includes altitude restrictions, a top altitude and instructions to expect the filed altitude ten minutes after departure). Before departure ATC uses PDC, DCL or clearance delivery to issue the clearance: “Cleared to Johnston Airport, Scott One departure, Jonez transition, Q-OneForty-five. Climb via SID.” NOTE− In Example 3, the aircraft must comply with the Scott One departure lateral path and any published speed and altitude restrictions while climbing to the SID top altitude. 4. (Using the Example 3 flight plan, ATC determines the top altitude must be changed to FL180). The clearance will read: “Cleared to Johnston Airport, Scott One departure, Jonez transition, Q-One Forty-five, Climb via SID except maintain flight level one eight zero.” NOTE− In Example 4, the aircraft must comply with the Scott One departure lateral path and any published speed and altitude restrictions while climbing to FL180. The aircraft 5−2−12 3/15/07 12/2/21 6/17/21 must stop climb at FL180 until issued further clearance by ATC. 5. (An aircraft was issued the Suzan Two departure, “climb via SID” in the IFR departure clearance. After departure ATC must change a waypoint crossing restriction). The clearance will be: “Climb via SID except cross Mkala at or above seven thousand.” NOTE− In Example 5, the aircraft will comply with the Suzan Two departure lateral path and any published speed and altitude restrictions and climb so as to cross Mkala at or above 7,000; remainder of the departure must be flown as published. 6. (An aircraft was issued the Teddd One departure, “climb via SID” in the IFR departure clearance. An interim altitude of 10,000 was issued instead of the published top altitude of FL 230). After departure ATC is able to issue the published top altitude. The clearance will be: “Climb via SID.” NOTE− In Example 6, the aircraft will track laterally and vertically on the Teddd One departure and initially climb to 10,000; Once re-issued the “climb via” clearance the interim altitude is canceled aircraft will continue climb to FL230 while complying with published restrictions. 7. (An aircraft was issued the Bbear Two departure, “climb via SID” in the IFR departure clearance. An interim altitude of 16,000 was issued instead of the published top altitude of FL 190). After departure, ATC is able to issue a top altitude of FL300 and still requires compliance with the published SID restrictions. The clearance will be: “Climb via SID except maintain flight level three zero zero.” NOTE− In Example 7, the aircraft will track laterally and vertically on the Bbear Two departure and initially climb to 16,000; Once re-issued the “climb via” clearance the interim altitude is canceled and the aircraft will continue climb to FL300 while complying with published restrictions. 8. (An aircraft was issued the Bizee Two departure, “climb via SID.” After departure, ATC vectors the aircraft off of the SID, and then issues a direct routing to rejoin the SID at Rockr waypoint which does not have a published altitude restriction. ATC wants the aircraft to cross at or above 10,000). The clearance will read: “Proceed direct Rockr, cross Rockr at or above one-zero thousand, climb via the Bizee Two departure.” NOTE− In Example 8, the aircraft will join the Bizee Two SID at Rockr at or above 10,000 and then comply with the Departure Procedures 12/2/21 6/17/21 AIM published lateral path and any published speed or altitude restrictions while climbing to the SID top altitude. altitude restrictions: “Climb and maintain flight level two four zero.” 9. (An aircraft was issued the Suzan Two departure, “climb via SID” in the IFR departure clearance. After departure ATC vectors the aircraft off of the SID, and then clears the aircraft to rejoin the SID at Dvine waypoint, which has a published crossing restriction). The clearance will read: “Proceed direct Dvine, Climb via the Suzan Two departure.” NOTE− The published SID altitude restrictions are canceled; The aircraft should comply with the SID lateral path and begin an unrestricted climb to FL240. Compliance with published speed restrictions is still required unless specifically deleted by ATC. NOTE− In Example 9, the aircraft will join the Suzan Two departure at Dvine, at the published altitude, and then comply with the published lateral path and any published speed or altitude restrictions. 7. Pilots cleared for vertical navigation using the phraseology “climb via” must inform ATC, upon initial contact, of the altitude leaving and any assigned restrictions not published on the procedure. EXAMPLE− 1. (Cactus 711 is cleared to climb via the Laura Two departure. The Laura Two has a top altitude of FL190): “Cactus Seven Eleven leaving two thousand, climbing via the Laura Two departure.” 2. (Cactus 711 is cleared to climb via the Laura Two departure, but ATC changed the top altitude to16,000): “Cactus Seven Eleven leaving two thousand for one-six thousand, climbing via the Laura Two departure.” 8. If prior to or after takeoff an altitude restriction is issued by ATC, all previously issued “ATC” altitude restrictions are canceled including those published on a SID. Pilots must still comply with all speed restrictions and lateral path requirements published on the SID unless canceled by ATC. EXAMPLE− Prior to takeoff or after departure ATC issues an altitude change clearance to an aircraft cleared to climb via a SID but ATC no longer requires compliance with published Departure Procedures 9. Altitude restrictions published on an ODP are necessary for obstacle clearance and/or design constraints. Crossing altitudes and speed restrictions on ODPs cannot be canceled or amended by ATC. i. PBN Departure Procedures 1. All public PBN SIDs and graphic ODPs are normally designed using RNAV 1, RNP 1, or A−RNP NavSpecs. These procedures generally start with an initial track or heading leg near the departure end of runway (DER). In addition, these procedures require system performance currently met by GPS or DME/DME/IRU PBN systems that satisfy the criteria discussed in the latest AC 90−100, U.S. Terminal and En Route Area Navigation (RNAV) Operations. RNAV 1 and RNP 1 procedures must maintain a total system error of not more than 1 NM for 95 percent of the total flight time. Minimum values for A−RNP procedures will be charted in the PBN box (for example, 1.00 or 0.30). 2. In the U.S., a specific procedure’s PBN requirements will be prominently displayed in separate, standardized notes boxes. For procedures with PBN elements, the “PBN box” will contain the procedure’s NavSpec(s); and, if required: specific sensors or infrastructure needed for the navigation solution, any additional or advanced functional requirements, the minimum RNP value, and any amplifying remarks. Items listed in this PBN box are REQUIRED for the procedure’s PBN elements. 5−2−13 6/17/21 AIM Section 3. En Route Procedures 5−3−1. ARTCC Communications a. Direct Communications, Controllers and Pilots. 1. ARTCCs are capable of direct communications with IFR air traffic on certain frequencies. Maximum communications coverage is possible through the use of Remote Center Air/Ground (RCAG) sites comprised of both VHF and UHF transmitters and receivers. These sites are located throughout the U.S. Although they may be several hundred miles away from the ARTCC, they are remoted to the various ARTCCs by land lines or microwave links. Since IFR operations are expedited through the use of direct communications, pilots are requested to use these frequencies strictly for communications pertinent to the control of IFR aircraft. Flight plan filing, en route weather, weather forecasts, and similar data should be requested through FSSs, company radio, or appropriate military facilities capable of performing these services. 2. An ARTCC is divided into sectors. Each sector is handled by one or a team of controllers and has its own sector discrete frequency. As a flight progresses from one sector to another, the pilot is requested to change to the appropriate sector discrete frequency. 3. Controller Pilot Data Link Communications (CPDLC) is a system that supplements air/ground voice communications. The CPDLC’s principal operating criteria are: (a) Voice remains the primary and controlling air/ground communications means. (b) Participating aircraft will need to have the appropriate CPDLC avionics equipment in order to receive uplink or transmit downlink messages. (c) En Route CPDLC Initial Services offer the following services: Altimeter Setting (AS), Transfer of Communications (TOC), Initial Contact (IC), and limited route assignments, including airborne reroutes (ABRR), limited altitude assignments, and emergency messages. (1) Altimeter settings will be uplinked automatically when appropriate after a Monitor TOC. En Route Procedures Altimeter settings will also be uplinked automatically when an aircraft receives an uplinked altitude assignment below FL 180. A controller may also manually send an altimeter setting message. NOTE− When conducting instrument approach procedures, pilots are responsible to obtain and use the appropriate altimeter setting in accordance with 14 CFR Section 97.20. CPDLC issued altimeter settings are excluded for this purpose. (2) Initial contact is a safety validation transaction that compares a pilot’s initiated altitude downlink message with an aircraft’s stored altitude in the ATC automation system. When an IC mismatch or Confirm Assigned Altitude (CAA) downlink time−out indicator is displayed in the Full Data Block (FDB) and Aircraft List (ACL), the controller who has track control of the aircraft must use voice communication to verify the assigned altitude of the aircraft, and acknowledge the IC mismatch/time−out indicator. (3) Transfer of communications automatically establishes data link contact with a succeeding sector. (4) Menu text transmissions are scripted nontrajectory altering uplink messages. (5) The CPDLC Message Elements for the Initial Capabilities rollout are contained in TBL 5−3−1 through TBL 5−3−19, CPDLC Message Elements, below. NOTE− The FAA is not implementing ATN B1; the ATN B1 column in the tables is there for informational purposes only. b. ATC Frequency Change Procedures. 1. The following phraseology will be used by controllers to effect a frequency change: EXAMPLE− (Aircraft identification) contact (facility name or location name and terminal function) (frequency) at (time, fix, or altitude). NOTE− Pilots are expected to maintain a listening watch on the transferring controller’s frequency until the time, fix, or altitude specified. ATC will omit frequency change restrictions whenever pilot compliance is expected upon receipt. 5−3−1 AIM 6/17/21 TBL 5−3−1 Route Uplink Message Elements (RTEU) CPDLC Message Sets FANS 1/A ATN B1 Operational Definition in PANS−ATM (Doc 4444) Response Message Element Identifier Message Element Intended Use Format for Message Element Display UM74 PROCEED DIRECT TO (position) UM74 PROCEED DIRECT TO (position) W/U RTEU−2 Instruction to proceed directly to the specified position. PROCEED DIRECT TO (position) UM79 CLEARED TO (position) via (route clearance) UM79 CLEARED TO (position) via (route clearance) W/U RTEU−6 Instruction to proceed to the specified position via the specified route. CLEARED TO (position) VIA (departure data[O]) (en−route data) UM80 CLEARED (route clearance) UM80 CLEARED (route clearance) W/U RTEU−7 Instruction to proceed via the specified route. CLEARED (departure data[O]) (en−route data) (arrival approach data) W/U RTEU−9 Instruction to proceed from the specified position via the specified route. AT (position) CLEARED (en−route data) (arrival approach data) UM83 AT (position) CLEARED (route clearance) N/A TBL 5−3−2 Route Downlink Message Elements (RTED) CPDLC Message Sets FANS 1/A DM22 REQUEST DIRECT TO (position) 5−3−2 ATN B1 DM22 REQUEST DIRECT TO (position) Operational Definition in PANS−ATM (Doc 4444) Response Message Element Identifier Y RTED−1 Message Element Intended Use Request for a direct clearance to the specified position. Format for Message Element Display REQUEST DIRECT TO (position) En Route Procedures 6/17/21 AIM TBL 5−3−3 Lateral Downlink Message Elements (LATD) CPDLC Message Sets Operational Definition in PANS−ATM (Doc 4444) FANS 1/A ATN B1 Response Message Element Identifier DM59 DIVERTING TO (position) VIA (route clearance) Note 1. − H alert attribute Note 2. − N response attribute N/A N1 LATD−5 Report indicating diverting to the specified position via the specified route, which may be sent without any previous coordination done with ATC. DIVERTING TO (position) VIA (en− route data) (arrival approach data[O]) DM60 OFFSETTING (distance offset) (direction) OF ROUTE Note 1. − H alert attribute Note 2. − N response attribute N/A N1 LATD−6 Report indicating that the aircraft is offsetting to a parallel track at the specified distance in the specified direction off from the cleared route. OFFSETTING (specified distance) (direction) OF ROUTE DM80 DEVIATING (deviation offset) (direction) OF ROUTE Note 1. − H alert attribute Note 2. − N response attribute N/A N1 LATD−7 Report indicating deviating specified distance or degrees in the specified direction from the cleared route. DEVIATING (specifiedDeviation) (direction) OF ROUTE Message Element Intended Use Format for Message Element Display 1 ICAO Document 10037, Global Operational Data Link (GOLD) Manual has these values set to Y in their table. TBL 5−3−4 Level Uplink Message Elements (LVLU) CPDLC Message Sets Operational Definition in PANS−ATM (Doc 4444) FANS 1/A ATN B1 Response Message Element Identifier UM19 MAINTAIN (altitude) Note − Used for a single level UM19 MAINTAIN (level) W/U LVLU−5 Instruction to maintain the specified level or vertical range. MAINTAIN (level) UM20 CLIMB TO AND MAINTAIN (altitude) Note − Used for a single level UM20 CLIMB TO (level) W/U LVLU−6 Instruction that a climb to the specified level or vertical range is to commence and once reached is to be maintained. CLIMB TO (level) En Route Procedures Message Element Intended Use Format for Message Element Display 5−3−3 AIM 6/17/21 CPDLC Message Sets Operational Definition in PANS−ATM (Doc 4444) Response Message Element Identifier UM23 DESCEND TO UM23 DESCEND AND MAINTAIN TO (level) (altitude) Note − Used for a single level W/U LVLU−9 Instruction that a DESCEND TO (level) descent to the specified level or vertical range is to commence and once reached is to be maintained. UM36 EXPEDITE CLIMB TO (altitude) Note − This message element is equivalent to SUPU−3 plus LVLU−6 in Doc 4444. N/A W/U LVLU−6 Instruction that a climb to the specified level or vertical range is to commence and once reached is to be maintained. UM37 EXPEDITE DESCEND TO (altitude) N/A W/U LVLU−9 Instruction that a DESCEND TO (level) descent to the specified level or vertical range is to commence and once reached is to be maintained. UM38 IMMEDIATELY CLIMB TO (altitude) Note − This message element is equivalent to EMGU−2 plus LVLU−6 in Doc 4444. N/A W/U LVLU−6 Instruction that a climb to the specified level or vertical range is to commence and once reached is to be maintained. UM39 IMMEDIATELY DESCEND TO (altitude) Note − This message element is equivalent to EMGU−2 plus LVLU−9 in Doc 4444. N/A W/U LVLU−9 Instruction that a DESCEND TO (level) descent to the specified level or vertical range is to commence and once reached is to be maintained. UM135 CONFIRM ASSIGNED ALTITUDE Note − NE response attribute N/A Y LVLU−27 Request to confirm CONFIRM ASthe assigned level. SIGNED LEVEL UM177 AT PILOTS DISCRETION N/A NE See Note Request to confirm the assigned level. FANS 1/A ATN B1 Message Element Intended Use Format for Message Element Display CLIMB TO (level) CLIMB TO (level) NOTE− ICAO Document 10037, Global Operational Data Link (GOLD) Manual does not include this in its tables. 5−3−4 En Route Procedures 6/17/21 AIM TBL 5−3−5 Level Downlink Message Elements (LVLD) CPDLC Message Sets FANS 1/A ATN B1 DM6 REQUEST (alti- DM6 REQUEST (level) tude) Note − Used for a single level Operational Definition in PANS−ATM (Doc 4444) Format for Message Element Display Response Message Element Identifier Y LVLD−1 Request to fly at the specified level or vertical range. REQUEST (level) Message Element Intended Use DM9 REQUEST CLIMB TO (altitude) DM9 REQUEST CLIMB TO (level) Y LVLD−2 Request for a climb to the specified level or vertical range. REQUEST CLIMB TO (level) DM10 REQUEST DESCENT TO (altitude) DM10 REQUEST DESCENT TO (level) Y LVLD−3 Request for a descent to the specified level or vertical range. REQUEST DESCENT TO (level) DM38 ASSIGNED LEVEL (altitude) Note − Used for a single level DM38 ASSIGNED LEVEL (level) N LVLD−11 Confirmation that the assigned level or vertical range is the specified level or vertical range. ASSIGNED LEVEL (level) N LVLD−14 Report indicating descending to the specified level. DESCENDING TO (level single) DM61 DESCENDING TO (altitude) Note − urgent alert attribute En Route Procedures N/A 5−3−5 AIM 6/17/21 TBL 5−3−6 Crossing Constraint Message Elements (CSTU) CPDLC Message Sets Operational Definition in PANS−ATM (Doc 4444) Format for Message Element Display FANS 1/A ATN B1 Response Message Element Identifier UM49 CROSS (position) AT AND MAINTAIN (altitude) Note 1. − A vertical range cannot be provided. Note 2. − This message element is equivalent to CSTU−1 plus LVLU−5 in Doc 4444. N/A W/U CSTU−1 Instruction that the CROSS (position) AT (level) specified position is to be crossed at the specified level or within the specified vertical range. UM61 CROSS (position) AT AND MAINTAIN (altitude) AT (speed) Note 1. − A vertical range cannot be provided. Note 2. − This message element is equivalent to CSTU−14 plus LVLU−5 in Doc 4444. UM61 CROSS (position) AT AND MAINTAIN (level) AT (speed) W/U CSTU−14 Instruction that the specified position is to be crossed at the level or within the vertical range, as specified, and at the specified speed. Message Element Intended Use CROSS (position) AT (level) AT (speed) TBL 5−3−7 Air Traffic Advisory Uplink Message Elements CPDLC Message Sets FANS 1/A UM154 RADAR SERVICES TERMINATED 5−3−6 Operational Definition in PANS−ATM (Doc 4444) ATN B1 Response Message Element Identifier N/A R ADVU−2 Message Element Intended Use Format for Message Element Display SURVEILLANCE Advisory that the SERVICE TERMIATS surveillance service is terminat- NATED ed. En Route Procedures 6/17/21 AIM TBL 5−3−8 Voice Communications Uplink Message Elements (COMU) CPDLC Message Sets Operational Definition in PANS−ATM (Doc 4444) ATN B1 Response Message Element Identifier UM117 CONTACT (ICAO unit name) (frequency) UM117 CONTACT (unit name) (frequency) W/U COMU−1 Instruction to establish voice contact with the specified ATS unit on the specified frequency. UM120 MONITOR (ICAO unit name) (frequency) UM120 MONITOR (unit name) (frequency) W/U COMU−5 Instruction to mon- MONITOR (unit name) itor the specified (frequency) ATS unit on the specified frequency. The flight crew is not required to establish voice contact on the frequency. FANS 1/A Message Element Intended Use Format for Message Element Display CONTACT (unit name) (frequency) TBL 5−3−9 Voice Communications Downlink Message Elements (COMD) CPDLC Message Sets FANS 1/A DM20 REQUEST VOICE CONTACT Note − Used when a frequency is not required. Operational Definition in PANS−ATM (Doc 4444) ATN B1 Response Message Element Identifier N/A Y COMD−1 Message Element Intended Use Request for voice contact on the specified frequency. Format for Message Element Display REQUEST VOICE CONTACT (frequency) TBL 5−3−10 Emergency/Urgency Uplink Message Elements (EMGU) CPDLC Message Sets FANS 1/A Used in combination with LVLU−6 and LVLU−9, which is implemented in FANS 1/A as: UM38 IMMEDIATELY CLIMB TO (altitude) Operational Definition in PANS−ATM (Doc 4444) ATN B1 Response Message Element Identifier N/A N EMGU−2 Message Element Intended Use Instruction to immediately comply with the associated instruction to avoid imminent situation. Format for Message Element Display Immediately UM39 IMMEDIATELY DESCEND TO (altitude) En Route Procedures 5−3−7 AIM 6/17/21 TBL 5−3−11 Emergency/Urgency Downlink Message Elements (EMGD) CPDLC Message Sets Operational Definition in PANS−ATM (Doc 4444) Format for Message Element Display FANS 1/A ATN B1 Response Message Element Identifier DM55 PAN PAN PAN Note − N response attribute N/A Y EMGD−1 Indication of an urgent situation. PAN PAN PAN DM56 MAYDAY MAYDAY MAYDAY Note − N response attribute N/A Y EMGD−2 Indication of an emergency situation. MAYDAY MAYDAY MAYDAY DM57 (remaining fuel) OF FUEL REMAINING AND (remaining souls) SOULS ON BOARD Note − N response attribute N/A Y EMGD−3 Report indicating fuel remaining (time) and number of persons on board. (remaining fuel) ENDURANCE AND (persons on board) PERSONS ON BOARD DM58 CANCEL EMERGENCY Note − N response attribute N/A Y EMGD−4 CANCEL Indication that the emergency situation EMERGENCY is canceled. Message Element Intended Use TBL 5−3−12 Standard Response Uplink Message Elements (RSPU) CPDLC Message Sets FANS 1/A ATN B1 Operational Definition in PANS−ATM (Doc 4444) Response Message Element Identifier Message Element Intended Use Format for Message Element Display UM0 UNABLE UM0 UNABLE N RSPU−1 Indication that the message cannot be complied with. UNABLE UM1 STANDBY UM1 STANDBY N RSPU−2 Indication that the message will be responded to shortly. STANDBY UM3 ROGER UM3 ROGER N RSPU−4 Indication that the message is received. ROGER 5−3−8 En Route Procedures 6/17/21 AIM TBL 5−3−13 Standard Response Downlink Message Elements (RSPD) CPDLC Message Sets FANS 1/A ATN B1 Operational Definition in PANS−ATM (Doc 4444) Response Message Element Identifier Message Element Intended Use Format for Message Element Display DM0 WILCO DM0 WILCO N RSPD−1 WILCO Indication that the instruction is understood and will be complied with. DM1 UNABLE DM1 UNABLE N RSPD−2 Indication that the message cannot be complied with. UNABLE DM2 STANDBY DM2 STANDBY N RSPD−3 Indication that the message will be responded to shortly. STANDBY DM3 ROGER Note − ROGER is the only correct response to an uplink free text message. DM3 ROGER N RSPD−4 Indication that the message is received. ROGER TBL 5−3−14 Supplemental Uplink Message Elements (SUPU) CPDLC Message Sets FANS 1/A UM166 DUE TO TRAFFIC UM167 DUE TO AIRSPACE RESTRICTION Operational Definition in PANS−ATM (Doc 4444) ATN B1 Response Message Element Identifier N/A N SUPU−2 Message Element Intended Use Indication that the associated message is issued due to the specified reason. Format for Message Element Display DUE TO (specified reason uplink) TBL 5−3−15 Supplemental Downlink Message Elements (SUPD) CPDLC Message Sets Operational Definition in PANS−ATM (Doc 4444) FANS 1/A ATN B1 Response Message Element Identifier DM65 DUE TO WEATHER DM66 DUE TO AIRCRAFT PERFORMANCE DM65 DUE TO WEATHER DM66 DUE TO AIRCRAFT PERFORMANCE N SUPD−1 En Route Procedures Message Element Intended Use Indication that the associated message is issued due to the specified reason. Format for Message Element Display DUE TO (specified reason downlink) 5−3−9 AIM 6/17/21 TBL 5−3−16 Free Text Uplink Message Elements (TXTU) CPDLC Message Sets Operational Definition in PANS−ATM (Doc 4444) Format for Message Element Display ATN B1 Response Message Element Identifier UM203 (free text) R TXTU−1 (free text) Note−M alert attribute. UM169 (free text) CPDLC NOT IN USE UNTIL FURTHER NOTIFICATION N/A R See Note (free text) UM169 (free text) “[facility designation]” LOCAL ALTIMETER (for Altimeter Reporting Station) N/A R See Note (free text) UM169 (free text) “[facility designation] LOCAL ALTIMETER MORE THAN ONE HOUR” OLD N/A R See Note (free text) UM169 (free text) DUE TO WEATHER N/A R See Note (free text) UM169 (free text) REST OF ROUTE UNCHANGED N/A R See Note (free text) UM169 (free text) TRAFFIC FLOW MANAGEMENT REROUTE N/A R See Note (free text) FANS 1/A UM169 (free text) Message Element Intended Use NOTE− These are FAA scripted free text messages with no GOLD equivalent. 5−3−10 En Route Procedures 6/17/21 AIM TBL 5−3−17 Free Text Downlink Message Elements (TXTD) CPDLC Message Sets Operational Definition in PANS−ATM (Doc 4444) FANS 1/A ATN B1 Response Message Element Identifier DM68 (free text) Note 1. − Urgency or Distress Alr (M) N/A Y TXTD−1 Message Element Intended Use Format for Message Element Display (free text) Note − M alert attribute. Note 2. − Selecting any of the emergency message elements will result in this message element being enabled for the flight crew to include in the emergency message at their discretion. TBL 5−3−18 System Management Uplink Message Elements (SYSU) CPDLC Message Sets FANS 1/A ATN B1 Operational Definition in PANS−ATM (Doc 4444) Response Message Element Identifier Message Element Intended Use Format for Message Element Display UM159 ERROR (error information) UM159 ERROR (error information) N SYSU−1 System−generated notification of an error. ERROR (error information) UM160 NEXT DATA AUTHORITY (ICAO facility designation) Note − The facility designation is required. UM160 NEXT DATA AUTHORITY (facility) Note − Facility parameter can specify a facility designation or no facility. N SYSU−2 System−generated notification of the next data authority or the cancellation thereof. NEXT DATA AUTHORITY (facility designation [O]) TBL 5−3−19 System Management Downlink Message Elements (SYSD) CPDLC Message Sets FANS 1/A DM62 ERROR (error information) En Route Procedures ATN B1 DM62 ERROR (error information) Operational Definition in PANS−ATM (Doc 4444) Response Message Element Identifier N SYSD−1 Message Element Intended Use System−generated notification of an error. Format for Message Element Display SYSD−1 5−3−11 AIM 6/17/21 DM63 NOT CURRENT DATA AUTHORITY DM63 NOT CURRENT DATA AUTHORITY N SYSD−3 System−generated rejection of any CPDLC message sent from a ground facility that is not the current data authority. DM64 (ICAO facility designation) Note − Use by FANS 1/A aircraft in B1 environments. DM107 NOT AUTHORIZED NEXT DATA AUTHORITY Note − CDA and NDA cannot be provided. N SYSD−5 SYSD−5 System−generated notification that the ground system is not designated as the next data authority (NDA), indicating the identity of the current data authority (CDA). Identity of the NDA, if any, is also reported. 5−3−12 SYSD−3 En Route Procedures 6/17/21 2. The following phraseology should be utilized by pilots for establishing contact with the designated facility: (a) When operating in a radar environment: On initial contact, the pilot should inform the controller of the aircraft’s assigned altitude preceded by the words “level,” or “climbing to,” or “descending to,” as appropriate; and the aircraft’s present vacating altitude, if applicable. EXAMPLE− 1. (Name) CENTER, (aircraft identification), LEVEL (altitude or flight level). 2. (Name) CENTER, (aircraft identification), LEAVING (exact altitude or flight level), CLIMBING TO OR DESCENDING TO (altitude of flight level). NOTE− Exact altitude or flight level means to the nearest 100 foot increment. Exact altitude or flight level reports on initial contact provide ATC with information required prior to using Mode C altitude information for separation purposes. ment: (b) When operating in a nonradar environ- (1) On initial contact, the pilot should inform the controller of the aircraft’s present position, altitude and time estimate for the next reporting point. EXAMPLE− (Name) CENTER, (aircraft identification), (position), (altitude), ESTIMATING (reporting point) AT (time). (2) After initial contact, when a position report will be made, the pilot should give the controller a complete position report. EXAMPLE− (Name) CENTER, (aircraft identification), (position), (time), (altitude), (type of flight plan), (ETA and name of next reporting point), (the name of the next succeeding reporting point), AND (remarks). REFERENCE− AIM, Paragraph 5−3−2 , Position Reporting 3. At times controllers will ask pilots to verify that they are at a particular altitude. The phraseology used will be: “VERIFY AT (altitude).” In climbing or descending situations, controllers may ask pilots to “VERIFY ASSIGNED ALTITUDE AS (altitude).” Pilots should confirm that they are at the altitude stated by the controller or that the assigned altitude is correct as stated. If this is not the case, they should inform the controller of the actual altitude being maintained or the different assigned altitude. En Route Procedures AIM CAUTION− Pilots should not take action to change their actual altitude or different assigned altitude to the altitude stated in the controllers verification request unless the controller specifically authorizes a change. c. ARTCC Radio Frequency Outage. ARTCCs normally have at least one back-up radio receiver and transmitter system for each frequency, which can usually be placed into service quickly with little or no disruption of ATC service. Occasionally, technical problems may cause a delay but switchover seldom takes more than 60 seconds. When it appears that the outage will not be quickly remedied, the ARTCC will usually request a nearby aircraft, if there is one, to switch to the affected frequency to broadcast communications instructions. It is important, therefore, that the pilot wait at least 1 minute before deciding that the ARTCC has actually experienced a radio frequency failure. When such an outage does occur, the pilot should, if workload and equipment capability permit, maintain a listening watch on the affected frequency while attempting to comply with the following recommended communications procedures: 1. If two-way communications cannot be established with the ARTCC after changing frequencies, a pilot should attempt to recontact the transferring controller for the assignment of an alternative frequency or other instructions. 2. When an ARTCC radio frequency failure occurs after two-way communications have been established, the pilot should attempt to reestablish contact with the center on any other known ARTCC frequency, preferably that of the next responsible sector when practicable, and ask for instructions. However, when the next normal frequency change along the route is known to involve another ATC facility, the pilot should contact that facility, if feasible, for instructions. If communications cannot be reestablished by either method, the pilot is expected to request communications instructions from the FSS appropriate to the route of flight. NOTE− The exchange of information between an aircraft and an ARTCC through an FSS is quicker than relay via company radio because the FSS has direct interphone lines to the responsible ARTCC sector. Accordingly, when circumstances dictate a choice between the two, during an ARTCC frequency outage, relay via FSS radio is recommended. 5−3−13 AIM d. Oakland Oceanic FIR. The use of CPDLC and ADS−C in the Oakland Oceanic FIR (KZAK) is only permitted by Inmarsat and Iridium customers. All other forms of data link connectivity are not authorized. Users must ensure that the proper data link code is filed in Item 10a of the ICAO FPL in order to indicate which satellite medium(s) the aircraft is equipped with. The identifier for Inmarsat is J5 and the identifier for Iridium is J7. If J5 or J7 is not included in the ICAO FPL, then the LOGON will be rejected by KZAK and the aircraft will not be able to connect. e. New York Oceanic FIR. The use of CPDLC and ADS−C in the New York Oceanic FIR (KZWY) is only permitted by Inmarsat and Iridium customers. All other forms of data link connectivity are not authorized. Users must ensure that the proper data link code is filed in Item 10a of the ICAO FPL in order to indicate which satellite medium(s) the aircraft is equipped with. The identifier for Inmarsat is J5 and the identifier for Iridium is J7. If J5 or J7 is not included in the ICAO FPL, then the LOGON will be rejected by KZWY and the aircraft will not be able to connect. 5−3−2. Position Reporting The safety and effectiveness of traffic control depends to a large extent on accurate position reporting. In order to provide the proper separation and expedite aircraft movements, ATC must be able to make accurate estimates of the progress of every aircraft operating on an IFR flight plan. a. Position Identification. 1. When a position report is to be made passing a VOR radio facility, the time reported should be the time at which the first complete reversal of the “to/from” indicator is accomplished. 6/17/21 4. If a position is given with respect to distance and direction from a reporting point, the distance and direction should be computed as accurately as possible. 5. Except for terminal area transition purposes, position reports or navigation with reference to aids not established for use in the structure in which flight is being conducted will not normally be required by ATC. b. Position Reporting Points. CFRs require pilots to maintain a listening watch on the appropriate frequency and, unless operating under the provisions of subparagraph c, to furnish position reports passing certain reporting points. Reporting points are indicated by symbols on en route charts. The designated compulsory reporting point symbol is a and the “on request” reporting solid triangle point symbol is the open triangle . Reports passing an “on request” reporting point are only necessary when requested by ATC. c. Position Reporting Requirements. 1. Flights Along Airways or Routes. A position report is required by all flights regardless of altitude, including those operating in accordance with an ATC clearance specifying “VFR−on−top,” over each designated compulsory reporting point along the route being flown. 2. Flights Along a Direct Route. Regardless of the altitude or flight level being flown, including flights operating in accordance with an ATC clearance specifying “VFR−on−top,” pilots must report over each reporting point used in the flight plan to define the route of flight. 2. When a position report is made passing a facility by means of an airborne ADF, the time reported should be the time at which the indicator makes a complete reversal. 3. Flights in a Radar Environment. When informed by ATC that their aircraft are in “Radar Contact,” pilots should discontinue position reports over designated reporting points. They should resume normal position reporting when ATC advises “RADAR CONTACT LOST” or “RADAR SERVICE TERMINATED.” 3. When an aural or a light panel indication is used to determine the time passing a reporting point, such as a fan marker, Z marker, cone of silence or intersection of range courses, the time should be noted when the signal is first received and again when it ceases. The mean of these two times should then be taken as the actual time over the fix. 4. Flights in an Oceanic (Non-radar) Environment. Pilots must report over each point used in the flight plan to define the route of flight, even if the point is depicted on aeronautical charts as an “on request” (non-compulsory) reporting point. For aircraft providing automatic position reporting via an Automatic Dependent Surveillance-Contract 5−3−14 En Route Procedures 6/17/21 (ADS-C) logon, pilots should discontinue voice position reports. NOTE− ATC will inform pilots that they are in “radar contact”: (a) when their aircraft is initially identified in the ATC system; and (b) when radar identification is reestablished after radar service has been terminated or radar contact lost. Subsequent to being advised that the controller has established radar contact, this fact will not be repeated to the pilot when handed off to another controller. At times, the aircraft identity will be confirmed by the receiving controller; however, this should not be construed to mean that radar contact has been lost. The identity of transponder equipped aircraft will be confirmed by asking the pilot to “ident,” “squawk standby,” or to change codes. Aircraft without transponders will be advised of their position to confirm identity. In this case, the pilot is expected to advise the controller if in disagreement with the position given. Any pilot who cannot confirm the accuracy of the position given because of not being tuned to the NAVAID referenced by the controller, should ask for another radar position relative to the tuned in NAVAID. d. Position Report Items: 1. Position reports should include the following items: (a) Identification; (b) Position; (c) Time; (d) Altitude or flight level (include actual altitude or flight level when operating on a clearance specifying VFR−on−top); (e) Type of flight plan (not required in IFR position reports made directly to ARTCCs or approach control); (f) ETA and name of next reporting point; (g) The name only of the next succeeding reporting point along the route of flight; and (h) Pertinent remarks. 5−3−3. Additional Reports a. The following reports should be made to ATC or FSS facilities without a specific ATC request: AIM (a) When vacating any previously assigned altitude or flight level for a newly assigned altitude or flight level. (b) When an altitude change will be made if operating on a clearance specifying VFR−on−top. (c) When unable to climb/descend at a rate of a least 500 feet per minute. (d) When approach has been missed. (Request clearance for specific action; i.e., to alternative airport, another approach, etc.) (e) Change in the average true airspeed (at cruising altitude) when it varies by 5 percent or 10 knots (whichever is greater) from that filed in the flight plan. (f) The time and altitude or flight level upon reaching a holding fix or point to which cleared. point. (g) When leaving any assigned holding fix or NOTE− The reports in subparagraphs (f) and (g) may be omitted by pilots of aircraft involved in instrument training at military terminal area facilities when radar service is being provided. (h) Any loss, in controlled airspace, of VOR, TACAN, ADF, low frequency navigation receiver capability, GPS anomalies while using installed IFR−certified GPS/GNSS receivers, complete or partial loss of ILS receiver capability or impairment of air/ground communications capability. Reports should include aircraft identification, equipment affected, degree to which the capability to operate under IFR in the ATC system is impaired, and the nature and extent of assistance desired from ATC. NOTE− 1. Other equipment installed in an aircraft may effectively impair safety and/or the ability to operate under IFR. If such equipment (e.g., airborne weather radar) malfunctions and in the pilot’s judgment either safety or IFR capabilities are affected, reports should be made as above. 2. When reporting GPS anomalies, include the location and altitude of the anomaly. Be specific when describing the location and include duration of the anomaly if necessary. flight. (i) Any information relating to the safety of 2. When not in radar contact. 1. At all times. (a) When leaving final approach fix inbound on final approach (nonprecision approach) or when En Route Procedures 5−3−15 AIM leaving the outer marker or fix used in lieu of the outer marker inbound on final approach (precision approach). (b) A corrected estimate at anytime it becomes apparent that an estimate as previously submitted is in error in excess of 2 minutes. For flights in the North Atlantic (NAT), a revised estimate is required if the error is 3 minutes or more. b. Pilots encountering weather conditions which have not been forecast, or hazardous conditions which have been forecast, are expected to forward a report of such weather to ATC. REFERENCE− AIM, Para 7−1−18, Pilot Weather Reports (PIREPs). 14 CFR Section 91.183(B) and (C). 5−3−4. Airways and Route Systems a. Three fixed route systems are established for air navigation purposes. They are the Federal airway system (consisting of VOR and L/MF routes), the jet route system, and the RNAV route system. To the extent possible, these route systems are aligned in an overlying manner to facilitate transition between each. 1. The VOR and L/MF (nondirectional radio beacons) Airway System consists of airways designated from 1,200 feet above the surface (or in some instances higher) up to but not including 18,000 feet MSL. These airways are depicted on IFR Enroute Low Altitude Charts. NOTE− The altitude limits of a victor airway should not be exceeded except to effect transition within or between route structures. (a) Except in Alaska, the VOR airways are: predicated solely on VOR or VORTAC navigation aids; depicted in black on aeronautical charts; and identified by a “V” (Victor) followed by the airway number (for example, V12). NOTE− Segments of VOR airways in Alaska are based on L/MF navigation aids and charted in brown instead of black on en route charts. (1) A segment of an airway which is common to two or more routes carries the numbers of all the airways which coincide for that segment. When such is the case, pilots filing a flight plan need to indicate only that airway number for the route filed. 5−3−16 6/17/21 NOTE− A pilot who intends to make an airway flight, using VOR facilities, will simply specify the appropriate “victor” airway(s) in the flight plan. For example, if a flight is to be made from Chicago to New Orleans at 8,000 feet, using omniranges only, the route may be indicated as “departing from Chicago−Midway, cruising 8,000 feet via Victor 9 to Moisant International.” If flight is to be conducted in part by means of L/MF navigation aids and in part on omniranges, specifications of the appropriate airways in the flight plan will indicate which types of facilities will be used along the described routes, and, for IFR flight, permit ATC to issue a traffic clearance accordingly. A route may also be described by specifying the station over which the flight will pass, but in this case since many VORs and L/MF aids have the same name, the pilot must be careful to indicate which aid will be used at a particular location. This will be indicated in the route of flight portion of the flight plan by specifying the type of facility to be used after the location name in the following manner: Newark L/MF, Allentown VOR. (2) With respect to position reporting, reporting points are designated for VOR Airway Systems. Flights using Victor Airways will report over these points unless advised otherwise by ATC. (b) The L/MF airways (colored airways) are predicated solely on L/MF navigation aids and are depicted in brown on aeronautical charts and are identified by color name and number (e.g., Amber One). Green and Red airways are plotted east and west. Amber and Blue airways are plotted north and south. NOTE− Except for G13 in North Carolina, the colored airway system exists only in the state of Alaska. All other such airways formerly so designated in the conterminous U.S. have been rescinded. (c) The use of TSO−C145 (as revised) or TSO−C146 (as revised) GPS/WAAS navigation systems is allowed in Alaska as the only means of navigation on published air traffic service (ATS) routes, including those Victor, T−Routes, and colored airway segments designated with a second minimum en route altitude (MEA) depicted in blue and followed by the letter G at those lower altitudes. The altitudes so depicted are below the minimum reception altitude (MRA) of the land−based navigation facility defining the route segment, and guarantee standard en route obstacle clearance and two−way communications. Air carrier operators requiring operations specifications are authorized to En Route Procedures 6/17/21 conduct operations on those routes in accordance with FAA operations specifications. 2. The jet route system consists of jet routes established from 18,000 feet MSL to FL 450 inclusive. (a) These routes are depicted on Enroute High Altitude Charts. Jet routes are depicted in black on aeronautical charts and are identified by a “J” (Jet) followed by the airway number (e.g., J12). Jet routes, as VOR airways, are predicated solely on VOR or VORTAC navigation facilities (except in Alaska). NOTE− Segments of jet routes in Alaska are based on L/MF navigation aids and are charted in brown color instead of black on en route charts. (b) With respect to position reporting, reporting points are designated for jet route systems. Flights using jet routes will report over these points unless otherwise advised by ATC. 3. Area Navigation (RNAV) Routes. (a) Published RNAV routes, including Q−Routes and T−Routes, can be flight planned for use by aircraft with RNAV capability, subject to any limitations or requirements noted on en route charts, in applicable Advisory Circulars, or by NOTAM. RNAV routes are depicted in blue on aeronautical charts and are identified by the letter “Q” or “T” followed by the airway number (for example, Q−13, T−205). Published RNAV routes are RNAV−2 except when specifically charted as RNAV−1. These routes require system performance currently met by GPS, GPS/WAAS, or DME/DME/IRU RNAV systems that satisfy the criteria discussed in AC 90−100A, U.S. Terminal and En Route Area Navigation (RNAV) Operations. AIM the surface (or in some instances higher) up to but not including 18,000 feet MSL. T−routes are depicted on Enroute Low Altitude Charts. NOTE− Aircraft in Alaska may only operate on GNSS T-routes with GPS/WAAS (TSO-C145 (as revised) or TSO-C146 (as revised)) equipment. (b) Unpublished RNAV routes are direct routes, based on area navigation capability, between waypoints defined in terms of latitude/longitude coordinates, degree−distance fixes, or offsets from established routes/airways at a specified distance and direction. Radar monitoring by ATC is required on all unpublished RNAV routes, except for GNSS− equipped aircraft cleared via filed published waypoints recallable from the aircraft’s navigation database. (c) Magnetic Reference Bearing (MRB) is the published bearing between two waypoints on an RNAV/GPS/GNSS route. The MRB is calculated by applying magnetic variation at the waypoint to the calculated true course between two waypoints. The MRB enhances situational awareness by indicating a reference bearing (no−wind heading) that a pilot should see on the compass/HSI/RMI, etc., when turning prior to/over a waypoint en route to another waypoint. Pilots should use this bearing as a reference only, because their RNAV/GPS/GNSS navigation system will fly the true course between the waypoints. b. Operation above FL 450 may be conducted on a point-to-point basis. Navigational guidance is provided on an area basis utilizing those facilities depicted on the enroute high altitude charts. NOTE− Aircraft in Alaska may only operate on GNSS Q-routes with GPS (TSO-C129 (as revised) or TSO-C196 (as revised)) equipment while the aircraft remains in Air Traffic Control (ATC) radar surveillance or with GPS/WAAS which does not require ATC radar surveillance. c. Radar Vectors. Controllers may vector aircraft within controlled airspace for separation purposes, noise abatement considerations, when an operational advantage will be realized by the pilot or the controller, or when requested by the pilot. Vectors outside of controlled airspace will be provided only on pilot request. Pilots will be advised as to what the vector is to achieve when the vector is controller initiated and will take the aircraft off a previously assigned nonradar route. To the extent possible, aircraft operating on RNAV routes will be allowed to remain on their own navigation. (2) T−routes are available for use by GPS or GPS/WAAS equipped aircraft from 1,200 feet above d. When flying in Canadian airspace, pilots are cautioned to review Canadian Air Regulations. (1) Q−routes are available for use by RNAV equipped aircraft between 18,000 feet MSL and FL 450 inclusive. Q−routes are depicted on Enroute High Altitude Charts. En Route Procedures 5−3−17 AIM 6/17/21 1. Special attention should be given to the parts which differ from U.S. CFRs. height of the terrain, no person may operate an aircraft under VMC within Class B airspace. (a) The Canadian Airways Class B airspace restriction is an example. Class B airspace is all controlled low level airspace above 12,500 feet MSL or the MEA, whichever is higher, within which only IFR and controlled VFR flights are permitted. (Low level airspace means an airspace designated and defined as such in the Designated Airspace Handbook.) (c) The requirement for entry into Class B airspace is a student pilot permit (under the guidance or control of a flight instructor). (b) Unless issued a VFR flight clearance by ATC, regardless of the weather conditions or the (d) VFR flight requires visual contact with the ground or water at all times. 2. Segments of VOR airways and high level routes in Canada are based on L/MF navigation aids and are charted in brown color instead of blue on en route charts. FIG 5−3−1 Adhering to Airways or Routes 5−3−5. Airway or Route Course Changes a. Pilots of aircraft are required to adhere to airways or routes being flown. Special attention must be given to this requirement during course changes. Each course change consists of variables that make the technique applicable in each case a matter only the pilot can resolve. Some variables which must be considered are turn radius, wind effect, airspeed, degree of turn, and cockpit instrumentation. An early turn, as illustrated below, is one method of adhering to airways or routes. The use of any available cockpit 5−3−18 instrumentation, such as Distance Measuring Equipment, may be used by the pilot to lead the turn when making course changes. This is consistent with the intent of 14 CFR Section 91.181, which requires pilots to operate along the centerline of an airway and along the direct course between navigational aids or fixes. b. Turns which begin at or after fix passage may exceed airway or route boundaries. FIG 5−3−1 contains an example flight track depicting this, together with an example of an early turn. En Route Procedures 6/17/21 c. Without such actions as leading a turn, aircraft operating in excess of 290 knots true air speed (TAS) can exceed the normal airway or route boundaries depending on the amount of course change required, wind direction and velocity, the character of the turn fix (DME, overhead navigation aid, or intersection), and the pilot’s technique in making a course change. For example, a flight operating at 17,000 feet MSL with a TAS of 400 knots, a 25 degree bank, and a course change of more than 40 degrees would exceed the width of the airway or route; i.e., 4 nautical miles each side of centerline. However, in the airspace below 18,000 feet MSL, operations in excess of 290 knots TAS are not prevalent and the provision of additional IFR separation in all course change situations for the occasional aircraft making a turn in excess of 290 knots TAS creates an unacceptable waste of airspace and imposes a penalty upon the preponderance of traffic which operate at low speeds. Consequently, the FAA expects pilots to lead turns and take other actions they consider necessary during course changes to adhere as closely as possible to the airways or route being flown. 5−3−6. Changeover Points (COPs) a. COPs are prescribed for Federal airways, jet routes, area navigation routes, or other direct routes for which an MEA is designated under 14 CFR Part 95. The COP is a point along the route or airway segment between two adjacent navigation facilities or waypoints where changeover in navigation guidance should occur. At this point, the pilot should change navigation receiver frequency from the station behind the aircraft to the station ahead. b. The COP is normally located midway between the navigation facilities for straight route segments, or at the intersection of radials or courses forming a dogleg in the case of dogleg route segments. When the COP is NOT located at the midway point, aeronautical charts will depict the COP location and give the mileage to the radio aids. c. COPs are established for the purpose of preventing loss of navigation guidance, to prevent frequency interference from other facilities, and to prevent use of different facilities by different aircraft in the same airspace. Pilots are urged to observe COPs to the fullest extent. En Route Procedures AIM 5−3−7. Minimum Turning Altitude (MTA) Due to increased airspeeds at 10,000 ft MSL or above, the published minimum enroute altitude (MEA) may not be sufficient for obstacle clearance when a turn is required over a fix, NAVAID, or waypoint. In these instances, an expanded area in the vicinity of the turn point is examined to determine whether the published MEA is sufficient for obstacle clearance. In some locations (normally mountainous), terrain/obstacles in the expanded search area may necessitate a higher minimum altitude while conducting the turning maneuver. Turning fixes requiring a higher minimum turning altitude (MTA) will be denoted on government charts by the minimum crossing altitude (MCA) icon (“x” flag) and an accompanying note describing the MTA restriction. An MTA restriction will normally consist of the air traffic service (ATS) route leading to the turn point, the ATS route leading from the turn point, and the required altitude; e.g., MTA V330 E TO V520 W 16000. When an MTA is applicable for the intended route of flight, pilots must ensure they are at or above the charted MTA not later than the turn point and maintain at or above the MTA until joining the centerline of the ATS route following the turn point. Once established on the centerline following the turning fix, the MEA/MOCA determines the minimum altitude available for assignment. An MTA may also preclude the use of a specific altitude or a range of altitudes during a turn. For example, the MTA may restrict the use of 10,000 through 11,000 ft MSL. In this case, any altitude greater than 11,000 ft MSL is unrestricted, as are altitudes less than 10,000 ft MSL provided MEA/MOCA requirements are satisfied. 5−3−8. Holding a. Whenever an aircraft is cleared to a fix other than the destination airport and delay is expected, it is the responsibility of ATC to issue complete holding instructions (unless the pattern is charted), an EFC time and best estimate of any additional en route/terminal delay. NOTE− Only those holding patterns depicted on U.S. government or commercially produced (meeting FAA requirements) low/high altitude en route, and area or STAR charts should be used. b. If the holding pattern is charted and the controller doesn’t issue complete holding instructions, the pilot is expected to hold as depicted on the 5−3−19 AIM 6/17/21 appropriate chart. When the pattern is charted on the assigned procedure or route being flown, ATC may omit all holding instructions except the charted holding direction and the statement AS PUBLISHED; for example, HOLD EAST AS PUBLISHED. ATC must always issue complete holding instructions when pilots request them. h. Patterns at the most generally used holding fixes are depicted (charted) on U.S. Government or commercially produced (meeting FAA requirements) Low or High Altitude En Route, Area, Departure Procedure, and STAR Charts. Pilots are expected to hold in the pattern depicted unless specifically advised otherwise by ATC. c. If no holding pattern is charted and holding instructions have not been issued, the pilot should ask ATC for holding instructions prior to reaching the fix. This procedure will eliminate the possibility of an aircraft entering a holding pattern other than that desired by ATC. If unable to obtain holding instructions prior to reaching the fix (due to frequency congestion, stuck microphone, etc.), then enter a standard pattern on the course on which the aircraft approached the fix and request further clearance as soon as possible. In this event, the altitude/flight level of the aircraft at the clearance limit will be protected so that separation will be provided as required. NOTE− Holding patterns that protect for a maximum holding airspeed other than the standard may be depicted by an icon, unless otherwise depicted. The icon is a standard holding pattern symbol (racetrack) with the airspeed restriction shown in the center. In other cases, the airspeed restriction will be depicted next to the standard holding pattern symbol. d. When an aircraft is 3 minutes or less from a clearance limit and a clearance beyond the fix has not been received, the pilot is expected to start a speed reduction so that the aircraft will cross the fix, initially, at or below the maximum holding airspeed. e. When no delay is expected, the controller should issue a clearance beyond the fix as soon as possible and, whenever possible, at least 5 minutes before the aircraft reaches the clearance limit. REFERENCE− AIM, Paragraph 5−3−8 j2, Holding i. An ATC clearance requiring an aircraft to hold at a fix where the pattern is not charted will include the following information: (See FIG 5−3−2.) 1. Direction of holding from the fix in terms of the eight cardinal compass points (i.e., N, NE, E, SE, etc.). 2. Holding fix (the fix may be omitted if included at the beginning of the transmission as the clearance limit). 3. Radial, course, bearing, airway or route on which the aircraft is to hold. f. Pilots should report to ATC the time and altitude/flight level at which the aircraft reaches the clearance limit and report leaving the clearance limit. 4. Leg length in miles if DME or RNAV is to be used (leg length will be specified in minutes on pilot request or if the controller considers it necessary). NOTE− In the event of two-way communications failure, pilots are required to comply with 14 CFR Section 91.185. 5. Direction of turn if left turns are to be made, the pilot requests, or the controller considers it necessary. g. When holding at a VOR station, pilots should begin the turn to the outbound leg at the time of the first complete reversal of the to/from indicator. 5−3−20 6. Time to expect further clearance and any pertinent additional delay information. En Route Procedures 6/17/21 AIM FIG 5−3−2 Holding Patterns EXAMPLES OF HOLDING L OM MM RUNWAY TYPICAL PROCEDURE ON AN ILS OUTER MARKER VOR VOR TYPICAL PROCEDURE AT INTERSECTION OF VOR RADIALS HOLDING COURSE TOWARD NAVAID HOLDING COURSE AWAY FROM NAVAID VORTAC 15 NM DME FIX 10 NM DME FIX TYPICAL PROCEDURE AT DME FIX En Route Procedures 5−3−21 AIM 6/17/21 FIG 5−3−3 Holding Pattern Descriptive Terms ABEAM OUTBOUND FIX END RECIPROCAL HOLDING SIDE INBOUND FIX NONHOLDING SIDE j. Holding pattern airspace protection is based on the following procedures. 1. Descriptive Terms. (a) Standard Pattern. Right turns (See FIG 5−3−3.) (b) Nonstandard Pattern. Left turns 2. Airspeeds. (a) All aircraft may hold at the following altitudes and maximum holding airspeeds: TBL 5−3−20 Altitude (MSL) MHA − 6,000’ 6,001’ − 14,000’ 14,001’ and above Airspeed (KIAS) 200 230 265 NOTE− These are the maximum indicated air speeds applicable to all holding. (b) The following are exceptions to the maximum holding airspeeds: (1) Holding patterns from 6,001’ to 14,000’ may be restricted to a maximum airspeed of 210 KIAS. This nonstandard pattern will be depicted by an icon. (2) Holding patterns may be restricted to a maximum speed. The speed restriction is depicted in parenthesis inside the holding pattern on the chart: e.g., (175). The aircraft should be at or below the maximum speed prior to initially crossing the holding 5−3−22 OUTBOUND END HOLDING COURSE fix to avoid exiting the protected airspace. Pilots unable to comply with the maximum airspeed restriction should notify ATC. (3) Holding patterns at USAF airfields only − 310 KIAS maximum, unless otherwise depicted. (4) Holding patterns at Navy fields only − 230 KIAS maximum, unless otherwise depicted. (5) All helicopter/power lift aircraft holding on a “COPTER” instrument procedure is predicated on a minimum airspeed of 90 KIAS unless charted otherwise. (6) When a climb−in hold is specified by a published procedure (for example, “Climb−in holding pattern to depart XYZ VORTAC at or above 10,000.” or “All aircraft climb−in TRUCK holding pattern to cross TRUCK Int at or above 11,500 before proceeding on course.”), additional obstacle protection area has been provided to allow for greater airspeeds in the climb for those aircraft requiring them. A maximum airspeed of 310 KIAS is permitted in Climb−in−holding, unless a maximum holding airspeed is published, in which case that maximum airspeed is applicable. The airspeed limitations in 14 CFR Section 91.117, Aircraft Speed, still apply. (c) The following phraseology may be used by an ATCS to advise a pilot of the maximum holding airspeed for a holding pattern airspace area. PHRASEOLOGY− (AIRCRAFT IDENTIFICATION) (holding instructions, when needed) MAXIMUM HOLDING AIRSPEED IS (speed in knots). En Route Procedures 6/17/21 AIM FIG 5−3−4 Holding Pattern Entry Procedures 3. Entry Procedures. Holding protected airspace is designed based in part on pilot compliance with the three recommended holding pattern entry procedures discussed below. Deviations from these recommendations, coupled with excessive airspeed crossing the holding fix, may in some cases result in the aircraft exceeding holding protected airspace. (See FIG 5−3−4.) (a) Parallel Procedure. When approaching the holding fix from anywhere in sector (a), the parallel entry procedure would be to turn to a heading to parallel the holding course outbound on the nonholding side for one minute, turn in the direction of the holding pattern through more than 180 degrees, and return to the holding fix or intercept the holding course inbound. (b) Teardrop Procedure. When approaching the holding fix from anywhere in sector (b), the teardrop entry procedure would be to fly to the fix, turn outbound to a heading for a 30 degree teardrop entry within the pattern (on the holding side) for a period of one minute, then turn in the direction of the holding pattern to intercept the inbound holding course. (c) Direct Entry Procedure. When approaching the holding fix from anywhere in sector (c), the direct entry procedure would be to fly En Route Procedures directly to the fix and turn to follow the holding pattern. (d) While other entry procedures may enable the aircraft to enter the holding pattern and remain within protected airspace, the parallel, teardrop and direct entries are the procedures for entry and holding recommended by the FAA, and were derived as part of the development of the size and shape of the obstacle protection areas for holding. (e) Nonstandard Holding Pattern. Fix end and outbound end turns are made to the left. Entry procedures to a nonstandard pattern are oriented in relation to the 70 degree line on the holding side just as in the standard pattern. 4. Timing. (a) Inbound Leg. (1) At or below 14,000 feet MSL: 1 minute. (2) Above 14,000 feet MSL: 11/2 minutes. NOTE− The initial outbound leg should be flown for 1 minute or 1 1/2 minutes (appropriate to altitude). Timing for subsequent outbound legs should be adjusted, as necessary, to achieve proper inbound leg time. Pilots may use any navigational means available; i.e., DME, RNAV, etc., to ensure the appropriate inbound leg times. (b) Outbound leg timing begins over/abeam the fix, whichever occurs later. If the abeam position 5−3−23 AIM 6/17/21 cannot be determined, start timing when turn to outbound is completed. 5. Distance Measuring Equipment (DME)/ GPS Along−Track Distance (ATD). DME/GPS holding is subject to the same entry and holding procedures except that distances (nautical miles) are used in lieu of time values. The outbound course of the DME/GPS holding pattern is called the outbound leg of the pattern. The controller or the instrument approach procedure chart will specify the length of the outbound leg. The end of the outbound leg is determined by the DME or ATD readout. The holding fix on conventional procedures, or controller defined holding based on a conventional navigation aid with DME, is a specified course or radial and distances are from the DME station for both the inbound and outbound ends of the holding pattern. When flying published GPS overlay or stand alone procedures with distance specified, the holding fix will be a waypoint in the database and the end of the outbound leg will be determined by the ATD. Some GPS overlay and early stand alone procedures may have timing specified. (See FIG 5−3−5, FIG 5−3−6 and FIG 5−3−7.) See Paragraph 1−1−17, Global Positioning System (GPS), for requirements and restriction on using GPS for IFR operations. FIG 5−3−5 Inbound Toward NAVAID NOTE− When the inbound course is toward the NAVAID, the fix distance is 10 NM, and the leg length is 5 NM, then the end of the outbound leg will be reached when the DME reads 15 NM. FIG 5−3−6 Inbound Leg Away from NAVAID NOTE− When the inbound course is away from the NAVAID and the fix distance is 28 NM, and the leg length is 8 NM, then the end of the outbound leg will be reached when the DME reads 20 NM. 5−3−24 En Route Procedures 6/17/21 AIM 6. Use of RNAV Distance in lieu of DME Distance. Substitution of RNAV computed distance to or from a NAVAID in place of DME distance is permitted when holding. However, the actual holding location and pattern flown will be further from the NAVAID than designed due to the lack of slant range in the position solution (see FIG 5−3−7). This may result in a slight difference between RNAV distance readout in reference to the NAVAID and the DME readout, especially at higher altitudes. When used solely for DME substitution, the difference between RNAV distance to/from a fix and DME slant range distance can be considered negligible and no pilot action is required. REFERENCE− AIM Paragraph 1−2−3, Use of Suitable Area Navigation (RNAV) Systems on Conventional Procedures and Routes FIG 5−3−7 Difference Between DME Distance From NAVAID & RNAV Computed Distance From NAVAID 7. Use of RNAV Guidance and Holding. RNAV systems, including multi−sensor Flight Management Systems (FMS) and stand−alone GPS receivers, may be used to furnish lateral guidance when executing a hold. The manner in which holding is implemented in an RNAV system varies widely between aircraft and RNAV system manufacturers. Holding pattern data may be extracted from the RNAV database for published holds or may be manually entered for ad−hoc ATC−assigned holds. Pilots are expected to be familiar with the capabilities and limitations of the specific RNAV system used for holding. (a) All holding, including holding defined on an RNAV or RNP procedure, is based on the conventional NAVAID holding design criteria, including the holding protected airspace construction. There are differences between the holding entry and flight track assumed in conventional holding pattern design and the entry and track that may be flown when RNAV guidance is used to execute holding. Individually, these differences may not affect the ability of the aircraft to remain within holding pattern protected airspace. However, cumu- En Route Procedures latively, they can result in deviations sufficient to result in excursions up to limits of the holding pattern protected airspace, and in some circumstances beyond protected airspace. The following difference and considerations apply when an RNAV system furnishes the lateral guidance used to fly a holding pattern: (1) Many systems use ground track angle instead of heading to select the entry method. While the holding pattern design allows a 5 degree tolerance, this may result in an unexpected entry when the winds induce a large drift angle. (2) The holding protected airspace is based on the assumption that the aircraft will fly−over the holding fix upon initial entry. RNAV systems may execute a “fly−by” turn when approaching the holding fix prior to entry. A “fly−by” turn during a direct entry from the holding pattern side of holding course may result in excursions beyond protected airspace, especially as the intercept angle and ground speed increase. (3) During holding, RNAV systems furnish lateral steering guidance using either a constant bank or constant radius to achieve the desired inbound and 5−3−25 AIM 6/17/21 outbound turns. An aircraft’s flight guidance system may use reduced bank angles for all turns including turns in holding, especially at higher altitudes, that may result in exceeding holding protected airspace. Use of a shallower bank angle will expand both the width and length of the aircraft track, especially as wind speed increases. If the flight guidance system’s bank angle limit feature is pilot−selectable, a minimum 25 degree bank angle should be selected regardless of altitude unless aircraft operating limitations specify otherwise and the pilot advises ATC. (4) Where a holding distance is published, the turn from the outbound leg begins at the published distance from the holding fix, thus establishing the design turn point required to remain within protected airspace. RNAV systems apply a database coded or pilot−entered leg distance as a maximum length of the inbound leg to the holding fix. The RNAV system then calculates a turn point from the outbound leg required to achieve this inbound leg length. This often results in an RNAV−calculated turn point on the outbound leg beyond the design turn point. (See FIG 5−3−8). With a strong headwind against the outbound leg, RNAV systems may fly up to and possibly beyond the limits of protected airspace before turning inbound. (See FIG 5−3−9.) This is especially true at higher altitudes where wind speeds are greater and ground speed results in a wider holding pattern. FIG 5−3−8 RNAV Lateral Guidance and Holding – No Wind FIG 5−3−9 RNAV Lateral Guidance and Holding – Effect of Wind 5−3−26 En Route Procedures 6/17/21 (5) Some RNAV systems compute the holding pattern based on the aircraft’s altitude and speed at a point prior to entering the hold. If the indicated airspeed is not reduced to comply with the maximum holding speed before this point, the computed pattern may exceed the protected airspace. Loading or executing a holding pattern may result in the speed and time limits applicable to the aircraft’s current altitude being used to define the holding pattern for RNAV lateral guidance. This may result in an incorrect hold being flown by the RNAV system. For example, entering or executing the holding pattern above 14,000 feet when intending to hold below 14,000 feet may result in applying 1 ½ minute timing below 14,000 feet. NOTE− Some systems permit the pilot to modify leg time of holding patterns defined in the navigation database; for example, a hold−in−lieu of procedure turn. In most RNAV systems, the holding pattern time remains at the pilot−modified time and will not revert back to the coded time if the aircraft descends to a lower altitude where a shorter time interval applies. (b) RNAV systems are not able to alert the pilot for excursions outside of holding pattern protected airspace since the dimensions of this airspace are not included in the navigation database. In addition, the dimensions of holding pattern protected airspace vary with altitude for a charted holding pattern, even when the hold is used for the same application. Close adherence to the pilot actions described in this section reduce the likelihood of exceeding the boundary of holding pattern protected airspace when using RNAV lateral guidance to conduct holding. (c) Holding patterns may be stored in the RNAV system’s navigation database and include coding with parameters defining how the RNAV system will conduct the hold. For example, coding will determine whether holding is conducted to manual termination (HM), continued holding until the aircraft reaches a specified altitude (HA), or holding is conducted until the holding fix is crossed the first time after entry (HF). Some systems do not store all holding patterns, and may only store patterns associated with missed approaches and hold−in−lieu of procedure turn (HILPT). Some store all holding as standard patterns and require pilot action to conduct non−standard holding (left turns). En Route Procedures AIM (1) Pilots are cautioned that multiple holding patterns may be established at the same fix. These holding patterns may differ in respect to turn directions and leg lengths depending on their application as an en route holding pattern, a holding pattern charted on a SID or STAR, or when used on an instrument approach procedure. Many RNAV systems limit the database coding at a particular fix to a single holding pattern definition. Pilots extracting the holding pattern from the navigation database are responsible for confirming that the holding pattern conforms to the assigned charted holding pattern in terms of turn direction, speed limit, timing, and distance. (2) If ATC assigns holding that is not charted, then the pilot is responsible for programming the RNAV system with the assigned holding course, turn direction, speed limit, leg length, or leg time. (3) Changes made after the initial execution may not apply until the next circuit of the holding pattern if the aircraft is in close proximity to the holding fix. 8. Pilot Action. The following actions are recommended to ensure that the aircraft remains within holding protected airspace when holding is performed using either conventional NAVAID guidance or when using RNAV lateral guidance. (a) Speed. When ATC furnishes advance notice of holding, start speed reduction to be at or below the maximum holding speed allowed at least 3 minutes prior to crossing the holding fix. If advance notice by ATC is not provided, begin speed reduction as expeditiously as practical. It is acceptable to allow RNAV systems to determine an appropriate deceleration point prior to the holding fix and to manage the speed reduction to the RNAV computed holding speed. If the pilot does not permit the RNAV system to manage the deceleration from the computed point, the actual hold pattern size at holding entry may differ from the holding pattern size computed by the RNAV system. (1) Aircraft are expected to enter holding at or below the maximum holding speed established in paragraph 5−3−8 j 2(a) or the charted maximum holding speed. [a] All fixed wing aircraft conducting holding should fly at speeds at or above 90 KIAS to minimize the influence of wind drift. 5−3−27 AIM 6/17/21 [b] When RNAV lateral guidance is used in fixed wing airplanes, it is desirable to enter and conduct holding at the lowest practical airspeed consistent with the airplane’s recommended holding speed to address the cumulative errors associated with RNAV holding and increase the probability of remaining within protected airspace. It is acceptable to allow RNAV systems to determine a recommended holding speed that is at or below the maximum holding speed. [c] Helicopter holding is based on a minimum airspeed of 90 KIAS. (2) Advise ATC immediately if unable to comply with the maximum holding airspeed and request an alternate clearance. NOTE− Speeds above the maximum or published holding speed may be necessary due to turbulence, icing, etc. Exceeding maximum holding airspeed may result in aircraft excursions beyond the holding pattern protected airspace. In a non−radar environment, the pilot should advise ATC that they cannot accept the assigned hold. (3) Ensure the RNAV system applies the proper time and speed restrictions to a holding pattern. This is especially critical when climbing or descending to a holding pattern altitude where time and speed restrictions are different than at the present aircraft altitude. (b) Bank Angle. For holding not involving the use of RNAV lateral guidance, make all turns during entry and while holding at: (1) 3 degrees per second, or (2) 30 degree bank angle, or (3) 25 degree bank angle, provided a flight director system is used. NOTE− Use whichever requires the least bank angle. (4) When using RNAV lateral guidance to conduct holding, it is acceptable to permit the RNAV system to calculate the appropriate bank angle for the outbound and inbound turns. Do not use flight guidance system bank angle limiting functions of less than 25 degrees unless the feature is not pilot−selectable, required by the aircraft limitations, or its use is necessary to comply with the aircraft’s minimum 5−3−28 maneuvering speed margins. If the bank angle must be limited to less than 25 degrees, advise ATC that additional area for holding is required. (c) Compensate for wind effect primarily by drift correction on the inbound and outbound legs. When outbound, triple the inbound drift correction to avoid major turning adjustments; for example, if correcting left by 8 degrees when inbound, correct right by 24 degrees when outbound. (d) Determine entry turn from aircraft heading upon arrival at the holding fix; +/− 5 degrees in heading is considered to be within allowable good operating limits for determining entry. When using RNAV lateral guidance for holding, it is permissible to allow the system to compute the holding entry. (e) RNAV lateral guidance may execute a fly−by turn beginning at an excessively large distance from the holding fix. Reducing speed to the maximum holding speed at least 3 minutes prior to reaching the holding fix and using the recommended 25 degree bank angle will reduce potential excursions beyond protected airspace. (f) When RNAV guidance is used for holding, pilots should be prepared to intervene if the turn from outbound leg to the inbound leg does not begin within a reasonable distance of the charted leg length, especially when holding is used as a course reversal HILPT. Pilot intervention is not required when holding in an ATC−assigned holding pattern that is not charted. However, notify ATC when the outbound leg length becomes excessive when RNAV guidance is used for holding. k. When holding at a fix and instructions are received specifying the time of departure from the fix, the pilot should adjust the aircraft’s flight path within the limits of the established holding pattern in order to leave the fix at the exact time specified. After departing the holding fix, normal speed is to be resumed with respect to other governing speed requirements, such as terminal area speed limits, specific ATC requests, etc. Where the fix is associated with an instrument approach and timed approaches are in effect, a procedure turn must not be executed unless the pilot advises ATC, since aircraft holding are expected to proceed inbound on final approach directly from the holding pattern when approach clearance is received. En Route Procedures 6/17/21 l. Radar surveillance of holding pattern airspace areas. 1. Whenever aircraft are holding, ATC will usually provide radar surveillance of the holding airspace on the controller’s radar display. 2. The controller will attempt to detect any holding aircraft that stray outside the holding airspace and will assist any detected aircraft to return to the assigned airspace. NOTE− Many factors could prevent ATC from providing this additional service, such as workload, number of targets, precipitation, ground clutter, and radar system capability. These circumstances may make it unfeasible to maintain radar identification of aircraft to detect aircraft straying from the holding pattern. The provision of this service depends entirely upon whether controllers believe they are in a position to provide it and does not relieve a pilot of their responsibility to adhere to an accepted ATC clearance. 3. ATC is responsible for traffic and obstruction separation when they have assigned holding that is En Route Procedures AIM not associated with a published (charted) holding pattern. Altitudes assigned will be at or above the minimum vectoring or minimum IFR altitude. 4. If an aircraft is established in a published holding pattern at an assigned altitude above the published minimum holding altitude and subsequently cleared for the approach, the pilot may descend to the published minimum holding altitude. The holding pattern would only be a segment of the IAP if it is published on the instrument procedure chart and is used in lieu of a procedure turn. m. For those holding patterns where there are no published minimum holding altitudes, the pilot, upon receiving an approach clearance, must maintain the last assigned altitude until leaving the holding pattern and established on the inbound course. Thereafter, the published minimum altitude of the route segment being flown will apply. It is expected that the pilot will be assigned a holding altitude that will permit a normal descent on the inbound course. 5−3−29 6/17/21 AIM Section 4. Arrival Procedures 5−4−1. Standard Terminal Arrival (STAR) Procedures a. A STAR is an ATC coded IFR arrival route established for application to arriving IFR aircraft destined for certain airports. STARs simplify clearance delivery procedures, and also facilitate transition between en route and instrument approach procedures. 1. STAR procedures may have mandatory speeds and/or crossing altitudes published. Other STARs may have planning information depicted to inform pilots what clearances or restrictions to “expect.” “Expect” altitudes/speeds are not considered STAR procedures crossing restrictions unless verbally issued by ATC. Published speed restrictions are independent of altitude restrictions and are mandatory unless modified by ATC. Pilots should plan to cross waypoints with a published speed restriction, at the published speed, and should not exceed this speed past the associated waypoint unless authorized by ATC or a published note to do so. NOTE− The “expect” altitudes/speeds are published so that pilots may have the information for planning purposes. These altitudes/speeds must not be used in the event of lost communications unless ATC has specifically advised the pilot to expect these altitudes/speeds as part of a further clearance. REFERENCE− 14 CFR Section 91.185(c)(2)(iii). 2. Pilots navigating on, or navigating a published route inbound to, a STAR procedure must maintain last assigned altitude until receiving authorization to descend so as to comply with all published/issued restrictions. This authorization will contain the phraseology “DESCEND VIA.” If vectored or cleared to deviate off a STAR, pilots must consider the STAR canceled, unless the controller adds “expect to resume STAR”; pilots should then be prepared to rejoin the STAR at a subsequent fix or procedure leg. If a descent clearance has been received that included a crossing restriction, pilots should expect the controller to issue an altitude to maintain. If the STAR contains published altitude and/or speed restrictions, those restrictions are Arrival Procedures canceled and pilots will receive an altitude to maintain and, if necessary, a speed. (a) Clearance to “descend via” authorizes pilots to: (1) Descend at pilot’s discretion to meet published restrictions and laterally navigate on a STAR. (2) When cleared to a waypoint depicted on a STAR, to descend from a previously assigned altitude at pilot’s discretion to the altitude depicted at that waypoint. (3) Once established on the depicted arrival, to descend and to meet all published or assigned altitude and/or speed restrictions. NOTE− 1. When otherwise cleared along a route or procedure that contains published speed restrictions, the pilot must comply with those speed restrictions independent of any descend via clearance. 2. ATC anticipates pilots will begin adjusting speed the minimum distance necessary prior to a published speed restriction so as to cross the waypoint/fix at the published speed. Once at the published speed, ATC expects pilots will maintain the published speed until additional adjustment is required to comply with further published or ATC assigned speed restrictions or as required to ensure compliance with 14 CFR Section 91.117. 3. The “descend via” is used in conjunction with STARs to reduce phraseology by not requiring the controller to restate the altitude at the next waypoint/fix to which the pilot has been cleared. 4. Air traffic will assign an altitude to cross the waypoint/ fix, if no altitude is depicted at the waypoint/fix, for aircraft on a direct routing to a STAR. Air traffic must ensure obstacle clearance when issuing a “descend via” instruction to the pilot. 5. Minimum en route altitudes (MEA) are not considered restrictions; however, pilots must remain above all MEAs, unless receiving an ATC instruction to descend below the MEA. EXAMPLE− 1. Lateral/routing clearance only. “Cleared Tyler One arrival.” NOTE− In Example 1, pilots are cleared to fly the lateral path of the procedure. Compliance with any published speed restrictions is required. No descent is authorized. 5−4−1 AIM 2. Routing with assigned altitude. “Cleared Tyler One arrival, descend and maintain flight level two four zero.” “Cleared Tyler One arrival, descend at pilot’s discretion, maintain flight level two four zero.” NOTE− In Example 2, the first clearance requires the pilot to descend to FL 240 as directed, comply with any published speed restrictions, and maintain FL 240 until cleared for further vertical navigation with a newly assigned altitude or a“descend via” clearance. The second clearance authorizes the pilot to descend to FL 240 at his discretion, to comply with any published speed restrictions, and then maintain FL 240 until issued further instructions. 3. Lateral/routing and vertical navigation clearance. “Descend via the Eagul Five arrival.” “Descend via the Eagul Five arrival, except, cross Vnnom at or above one two thousand.” NOTE− In Example 3, the first clearance authorized the aircraft to descend at pilot’s discretion on the Eagul Five arrival; the pilot must descend so as to comply with all published altitude and speed restrictions. The second clearance authorizes the same, but requires the pilot to descend so as to cross at Vnnom at or above 12,000. 4. Lateral/routing and vertical navigation clearance when assigning altitude not published on procedure. “Descend via the Eagul Five arrival, except after Geeno, maintain one zero thousand.” “Descend via the Eagul Five arrival, except cross Geeno at one one thousand then maintain seven thousand.” NOTE− In Example 4, the first clearance authorized the aircraft to track laterally on the Eagul Five Arrival and to descend at pilot’s discretion so as to comply with all altitude and speed restrictions until reaching Geeno and then maintain 10,000. Upon reaching 10,000, aircraft should maintain 10,000 until cleared by ATC to continue to descend. The second clearance requires the same, except the aircraft must cross Geeno at 11,000 and is then authorized to continue descent to and maintain 7,000. 5. Direct routing to intercept a STAR and vertical navigation clearance. “Proceed direct Leoni, descend via the Leoni One arrival.” “Proceed direct Denis, cross Denis at or above flight level two zero zero, then descend via the Mmell One arrival.” 5−4−2 6/17/21 NOTE− In Example 5, in the first clearance an altitude is published at Leoni; the aircraft proceeds to Leoni, crosses Leoni at the published altitude and then descends via the arrival. If a speed restrictions is published at Leoni, the aircraft will slow to comply with the published speed. In the second clearance, there is no altitude published at Denis; the aircraft must cross Denis at or above FL200, and then descends via the arrival. (b) Pilots cleared for vertical navigation using the phraseology “descend via” must inform ATC upon initial contact with a new frequency, of the altitude leaving, “descending via (procedure name),” the runway transition or landing direction if assigned, and any assigned restrictions not published on the procedure. EXAMPLE− 1. Delta 121 is cleared to descend via the Eagul Five arrival, runway 26 transition: “Delta One Twenty One leaving flight level one niner zero, descending via the Eagul Five arrival runway two-six transition.” 2. Delta 121 is cleared to descend via the Eagul Five arrival, but ATC has changed the bottom altitude to 12,000: “Delta One Twenty One leaving flight level one niner zero for one two thousand, descending via the Eagul Five arrival, runway two-six transition.” 3. (JetBlue 602 is cleared to descend via the Ivane Two arrival, landing south): “JetBlue six zero two leaving flight level two one zero descending via the Ivane Two arrival landing south.” b. Pilots of IFR aircraft destined to locations for which STARs have been published may be issued a clearance containing a STAR whenever ATC deems it appropriate. c. Use of STARs requires pilot possession of at least the approved chart. RNAV STARs must be retrievable by the procedure name from the aircraft database and conform to charted procedure. As with any ATC clearance or portion thereof, it is the responsibility of each pilot to accept or refuse an issued STAR. Pilots should notify ATC if they do not wish to use a STAR by placing “NO STAR” in the remarks section of the flight plan or by the less desirable method of verbally stating the same to ATC. d. STAR charts are published in the Terminal Procedures Publications (TPP) and are available on subscription from the National Aeronautical Charting Office. Arrival Procedures 6/17/21 e. PBN STAR. 1. Public PBN STARs are normally designed using RNAV 1, RNP 1, or A−RNP NavSpecs. These procedures require system performance currently met by GPS or DME/DME/IRU PBN systems that satisfy the criteria discussed in AC 90−100A, U.S. Terminal and En Route Area Navigation (RNAV) Operations. These procedures, using RNAV 1 and RNP 1 NavSpecs, must maintain a total system error of not more than 1 NM for 95% of the total flight time. Minimum values for A−RNP procedures will be charted in the PBN box (for example, 1.00 or 0.30). 2. In the U.S., a specific procedure’s PBN requirements will be prominently displayed in separate, standardized notes boxes. For procedures with PBN elements, the “PBN box” will contain the procedure’s NavSpec(s); and, if required: specific sensors or infrastructure needed for the navigation solution, any additional or advanced functional requirements, the minimum RNP value, and any amplifying remarks. Items listed in this PBN box are REQUIRED for the procedure’s PBN elements. 5−4−2. Local Flow Traffic Management Program a. This program is a continuing effort by the FAA to enhance safety, minimize the impact of aircraft noise and conserve aviation fuel. The enhancement of safety and reduction of noise is achieved in this program by minimizing low altitude maneuvering of arriving turbojet and turboprop aircraft weighing more than 12,500 pounds and, by permitting departure aircraft to climb to higher altitudes sooner, as arrivals are operating at higher altitudes at the points where their flight paths cross. The application of these procedures also reduces exposure time between controlled aircraft and uncontrolled aircraft at the lower altitudes in and around the terminal environment. Fuel conservation is accomplished by absorbing any necessary arrival delays for aircraft included in this program operating at the higher and more fuel efficient altitudes. b. A fuel efficient descent is basically an uninterrupted descent (except where level flight is required for speed adjustment) from cruising altitude to the point when level flight is necessary for the pilot to stabilize the aircraft on final approach. The procedure for a fuel efficient descent is based on an altitude loss which is most efficient for the majority Arrival Procedures AIM of aircraft being served. This will generally result in a descent gradient window of 250−350 feet per nautical mile. c. When crossing altitudes and speed restrictions are issued verbally or are depicted on a chart, ATC will expect the pilot to descend first to the crossing altitude and then reduce speed. Verbal clearances for descent will normally permit an uninterrupted descent in accordance with the procedure as described in paragraph b above. Acceptance of a charted fuel efficient descent (Runway Profile Descent) clearance requires the pilot to adhere to the altitudes, speeds, and headings depicted on the charts unless otherwise instructed by ATC. PILOTS RECEIVING A CLEARANCE FOR A FUEL EFFICIENT DESCENT ARE EXPECTED TO ADVISE ATC IF THEY DO NOT HAVE RUNWAY PROFILE DESCENT CHARTS PUBLISHED FOR THAT AIRPORT OR ARE UNABLE TO COMPLY WITH THE CLEARANCE. 5−4−3. Approach Control a. Approach control is responsible for controlling all instrument flight operating within its area of responsibility. Approach control may serve one or more airfields, and control is exercised primarily by direct pilot and controller communications. Prior to arriving at the destination radio facility, instructions will be received from ARTCC to contact approach control on a specified frequency. b. Radar Approach Control. 1. Where radar is approved for approach control service, it is used not only for radar approaches (Airport Surveillance Radar [ASR] and Precision Approach Radar [PAR]) but is also used to provide vectors in conjunction with published nonradar approaches based on radio NAVAIDs (ILS, VOR, NDB, TACAN). Radar vectors can provide course guidance and expedite traffic to the final approach course of any established IAP or to the traffic pattern for a visual approach. Approach control facilities that provide this radar service will operate in the following manner: (a) Arriving aircraft are either cleared to an outer fix most appropriate to the route being flown with vertical separation and, if required, given holding information or, when radar handoffs are effected between the ARTCC and approach control, or between two approach control facilities, aircraft 5−4−3 AIM are cleared to the airport or to a fix so located that the handoff will be completed prior to the time the aircraft reaches the fix. When radar handoffs are utilized, successive arriving flights may be handed off to approach control with radar separation in lieu of vertical separation. (b) After release to approach control, aircraft are vectored to the final approach course (ILS, RNAV, GLS, VOR, ADF, etc.). Radar vectors and altitude or flight levels will be issued as required for spacing and separating aircraft. Therefore, pilots must not deviate from the headings issued by approach control. Aircraft will normally be informed when it is necessary to vector across the final approach course for spacing or other reasons. If approach course crossing is imminent and the pilot has not been informed that the aircraft will be vectored across the final approach course, the pilot should query the controller. (c) The pilot is not expected to turn inbound on the final approach course unless an approach clearance has been issued. This clearance will normally be issued with the final vector for interception of the final approach course, and the vector will be such as to enable the pilot to establish the aircraft on the final approach course prior to reaching the final approach fix. (d) In the case of aircraft already inbound on the final approach course, approach clearance will be issued prior to the aircraft reaching the final approach fix. When established inbound on the final approach course, radar separation will be maintained and the pilot will be expected to complete the approach utilizing the approach aid designated in the clearance (ILS, RNAV, GLS, VOR, radio beacons, etc.) as the primary means of navigation. Therefore, once established on the final approach course, pilots must not deviate from it unless a clearance to do so is received from ATC. (e) After passing the final approach fix on final approach, aircraft are expected to continue inbound on the final approach course and complete the approach or effect the missed approach procedure published for that airport. 2. ARTCCs are approved for and may provide approach control services to specific airports. The radar systems used by these centers do not provide the same precision as an ASR/PAR used by approach 5−4−4 6/17/21 control facilities and towers, and the update rate is not as fast. Therefore, pilots may be requested to report established on the final approach course. 3. Whether aircraft are vectored to the appropriate final approach course or provide their own navigation on published routes to it, radar service is automatically terminated when the landing is completed or when instructed to change to advisory frequency at uncontrolled airports, whichever occurs first. 5−4−4. Advance Information on Instrument Approach a. When landing at airports with approach control services and where two or more IAPs are published, pilots will be provided in advance of their arrival with the type of approach to expect or that they may be vectored for a visual approach. This information will be broadcast either by a controller or on ATIS. It will not be furnished when the visibility is three miles or better and the ceiling is at or above the highest initial approach altitude established for any low altitude IAP for the airport. b. The purpose of this information is to aid the pilot in planning arrival actions; however, it is not an ATC clearance or commitment and is subject to change. Pilots should bear in mind that fluctuating weather, shifting winds, blocked runway, etc., are conditions which may result in changes to approach information previously received. It is important that pilots advise ATC immediately they are unable to execute the approach ATC advised will be used, or if they prefer another type of approach. c. Aircraft destined to uncontrolled airports, which have automated weather data with broadcast capability, should monitor the ASOS/AWOS frequency to ascertain the current weather for the airport. The pilot must advise ATC when he/she has received the broadcast weather and state his/her intentions. NOTE− 1. ASOS/AWOS should be set to provide one−minute broadcast weather updates at uncontrolled airports that are without weather broadcast capability by a human observer. 2. Controllers will consider the long line disseminated weather from an automated weather system at an uncontrolled airport as trend and planning information only and will rely on the pilot for current weather Arrival Procedures 6/17/21 information for the airport. If the pilot is unable to receive the current broadcast weather, the last long line disseminated weather will be issued to the pilot. When receiving IFR services, the pilot/aircraft operator is responsible for determining if weather/visibility is adequate for approach/landing. d. When making an IFR approach to an airport not served by a tower or FSS, after ATC advises “CHANGE TO ADVISORY FREQUENCY APPROVED” you should broadcast your intentions, including the type of approach being executed, your position, and when over the final approach fix inbound (nonprecision approach) or when over the outer marker or fix used in lieu of the outer marker inbound (precision approach). Continue to monitor the appropriate frequency (UNICOM, etc.) for reports from other pilots. 5−4−5. Instrument Approach Procedure (IAP) Charts a. 14 CFR Section 91.175(a), Instrument approaches to civil airports, requires the use of SIAPs prescribed for the airport in 14 CFR Part 97 unless otherwise authorized by the Administrator (including ATC). If there are military procedures published at a civil airport, aircraft operating under 14 CFR Part 91 must use the civil procedure(s). Civil procedures are defined with “FAA” in parenthesis; e.g., (FAA), at the top, center of the procedure chart. DOD procedures are defined using the abbreviation of the applicable military service in parenthesis; e.g., (USAF), (USN), (USA). 14 CFR Section 91.175(g), Military airports, requires civil pilots flying into or out of military airports to comply with the IAPs and takeoff and landing minimums prescribed by the authority having jurisdiction at those airports. Unless an emergency exists, civil aircraft operating at military airports normally require advance authorization, commonly referred to as “Prior Permission Required” or “PPR.” Information on obtaining a PPR for a particular military airport can be found in the Chart Supplement U.S. NOTE− Civil aircraft may conduct practice VFR approaches using DOD instrument approach procedures when approved by the air traffic controller. 1. IAPs (standard and special, civil and military) are based on joint civil and military criteria contained in the U.S. Standard for TERPS. The design of IAPs Arrival Procedures AIM based on criteria contained in TERPS, takes into account the interrelationship between airports, facilities, and the surrounding environment, terrain, obstacles, noise sensitivity, etc. Appropriate altitudes, courses, headings, distances, and other limitations are specified and, once approved, the procedures are published and distributed by government and commercial cartographers as instrument approach charts. 2. Not all IAPs are published in chart form. Radar IAPs are established where requirements and facilities exist but they are printed in tabular form in appropriate U.S. Government Flight Information Publications. 3. The navigation equipment required to join and fly an instrument approach procedure is indicated by the title of the procedure and notes on the chart. (a) Straight−in IAPs are identified by the navigational system providing the final approach guidance and the runway to which the approach is aligned (e.g., VOR RWY 13). Circling only approaches are identified by the navigational system providing final approach guidance and a letter (e.g., VOR A). More than one navigational system separated by a slash indicates that more than one type of equipment must be used to execute the final approach (e.g., VOR/DME RWY 31). More than one navigational system separated by the word “or” indicates either type of equipment may be used to execute the final approach (e.g., VOR or GPS RWY 15). (b) In some cases, other types of navigation systems including radar may be required to execute other portions of the approach or to navigate to the IAF (e.g., an NDB procedure turn to an ILS, an NDB in the missed approach, or radar required to join the procedure or identify a fix). When radar or other equipment is required for procedure entry from the en route environment, a note will be charted in the planview of the approach procedure chart (e.g., RADAR REQUIRED or ADF REQUIRED). When radar or other equipment is required on portions of the procedure outside the final approach segment, including the missed approach, a note will be charted in the notes box of the pilot briefing portion of the approach chart (e.g., RADAR REQUIRED or DME REQUIRED). Notes are not charted when VOR is required outside the final approach segment. Pilots should ensure that the 5−4−5 AIM aircraft is equipped with the required NAVAID(s) in order to execute the approach, including the missed approach. NOTE− Some military (i.e., U.S. Air Force and U.S. Navy) IAPs have these “additional equipment required” notes charted only in the planview of the approach procedure and do not conform to the same application standards used by the FAA. (c) The FAA has initiated a program to provide a new notation for LOC approaches when charted on an ILS approach requiring other navigational aids to fly the final approach course. The LOC minimums will be annotated with the NAVAID required (e.g., “DME Required” or “RADAR Required”). During the transition period, ILS approaches will still exist without the annotation. (d) Many ILS approaches having minima based on RVR are eligible for a landing minimum of RVR 1800. Some of these approaches are to runways that have touchdown zone and centerline lights. For many runways that do not have touchdown and centerline lights, it is still possible to allow a landing minimum of RVR 1800. For these runways, the normal ILS minimum of RVR 2400 can be annotated with a single or double asterisk or the dagger symbol “†”; for example “** 696/24 200 (200/1/2).” A note is included on the chart stating “**RVR 1800 authorized with use of FD or AP or HUD to DA.” The pilot must use the flight director, or autopilot with an approved approach coupler, or head up display to decision altitude or to the initiation of a missed approach. In the interest of safety, single pilot operators should not fly approaches to 1800 RVR minimums on runways without touchdown and centerline lights using only a flight director, unless accompanied by the use of an autopilot with an approach coupler. (e) The naming of multiple approaches of the same type to the same runway is also changing. Multiple approaches with the same guidance will be annotated with an alphabetical suffix beginning at the end of the alphabet and working backwards for subsequent procedures (e.g., ILS Z RWY 28, ILS Y RWY 28, etc.). The existing annotations such as ILS 2 RWY 28 or Silver ILS RWY 28 will be phased out and replaced with the new designation. The Cat II and Cat III designations are used to differentiate 5−4−6 6/17/21 between multiple ILSs to the same runway unless there are multiples of the same type. (f) RNAV (GPS) approaches to LNAV, LP, LNAV/VNAV and LPV lines of minima using WAAS and RNAV (GPS) approaches to LNAV and LNAV/VNAV lines of minima using GPS are charted as RNAV (GPS) RWY (Number) (e.g., RNAV (GPS) RWY 21). (g) Performance−Based Navigation (PBN) Box. As charts are updated, a procedure’s PBN requirements and conventional equipment requirements will be prominently displayed in separate, standardized notes boxes. For procedures with PBN elements, the PBN box will contain the procedure’s navigation specification(s); and, if required: specific sensors or infrastructure needed for the navigation solution, any additional or advanced functional requirements, the minimum Required Navigation Performance (RNP) value, and any amplifying remarks. Items listed in this PBN box are REQUIRED for the procedure’s PBN elements. For example, an ILS with an RNAV missed approach would require a specific capability to fly the missed approach portion of the procedure. That required capability will be listed in the PBN box. The separate Equipment Requirements box will list ground−based equipment requirements. On procedures with both PBN elements and equipment requirements, the PBN requirements box will be listed first. The publication of these notes will continue incrementally until all charts have been amended to comply with the new standard. 4. Approach minimums are based on the local altimeter setting for that airport, unless annotated otherwise; e.g., Oklahoma City/Will Rogers World approaches are based on having a Will Rogers World altimeter setting. When a different altimeter source is required, or more than one source is authorized, it will be annotated on the approach chart; e.g., use Sidney altimeter setting, if not received, use Scottsbluff altimeter setting. Approach minimums may be raised when a nonlocal altimeter source is authorized. When more than one altimeter source is authorized, and the minima are different, they will be shown by separate lines in the approach minima box or a note; e.g., use Manhattan altimeter setting; when not available use Salina altimeter setting and increase all MDAs 40 feet. When the altimeter must be obtained from a source other than air traffic a note will indicate the source; e.g., Obtain local altimeter setting on CTAF. Arrival Procedures 6/17/21 When the altimeter setting(s) on which the approach is based is not available, the approach is not authorized. Baro−VNAV must be flown using the local altimeter setting only. Where no local altimeter is available, the LNAV/VNAV line will still be published for use by WAAS receivers with a note that Baro−VNAV is not authorized. When a local and at least one other altimeter setting source is authorized and the local altimeter is not available Baro−VNAV is not authorized; however, the LNAV/VNAV minima can still be used by WAAS receivers using the alternate altimeter setting source. NOTE− Barometric Vertical Navigation (baro−VNAV). An RNAV system function which uses barometric altitude information from the aircraft’s altimeter to compute and present a vertical guidance path to the pilot. The specified vertical path is computed as a geometric path, typically computed between two waypoints or an angle based computation from a single waypoint. Further guidance may be found in Advisory Circular 90−105. 5. A pilot adhering to the altitudes, flight paths, and weather minimums depicted on the IAP chart or vectors and altitudes issued by the radar controller, is assured of terrain and obstruction clearance and runway or airport alignment during approach for landing. 6. IAPs are designed to provide an IFR descent from the en route environment to a point where a safe landing can be made. They are prescribed and approved by appropriate civil or military authority to ensure a safe descent during instrument flight conditions at a specific airport. It is important that pilots understand these procedures and their use prior to attempting to fly instrument approaches. 7. TERPS criteria are provided for the following types of instrument approach procedures: (a) Precision Approach (PA). An instrument approach based on a navigation system that provides course and glidepath deviation information meeting the precision standards of ICAO Annex 10. For example, PAR, ILS, and GLS are precision approaches. (b) Approach with Vertical Guidance (APV). An instrument approach based on a navigation system that is not required to meet the precision approach standards of ICAO Annex 10 but provides course and glidepath deviation information. For Arrival Procedures AIM example, Baro−VNAV, LDA with glidepath, LNAV/ VNAV and LPV are APV approaches. (c) Nonprecision Approach (NPA). An instrument approach based on a navigation system which provides course deviation information, but no glidepath deviation information. For example, VOR, NDB and LNAV. As noted in subparagraph k, Vertical Descent Angle (VDA) on Nonprecision Approaches, some approach procedures may provide a Vertical Descent Angle as an aid in flying a stabilized approach, without requiring its use in order to fly the procedure. This does not make the approach an APV procedure, since it must still be flown to an MDA and has not been evaluated with a glidepath. b. The method used to depict prescribed altitudes on instrument approach charts differs according to techniques employed by different chart publishers. Prescribed altitudes may be depicted in four different configurations: minimum, maximum, mandatory, and recommended. The U.S. Government distributes charts produced by National Geospatial−Intelligence Agency (NGA) and FAA. Altitudes are depicted on these charts in the profile view with underscore, overscore, both or none to identify them as minimum, maximum, mandatory or recommended. 1. Minimum altitude will be depicted with the altitude value underscored. Aircraft are required to maintain altitude at or above the depicted value, e.g., 3000. 2. Maximum altitude will be depicted with the altitude value overscored. Aircraft are required to maintain altitude at or below the depicted value, e.g., 4000. 3. Mandatory altitude will be depicted with the altitude value both underscored and overscored. Aircraft are required to maintain altitude at the depicted value, e.g., 5000. 4. Recommended altitude will be depicted with no overscore or underscore. These altitudes are depicted for descent planning, e.g., 6000. NOTE− 1. Pilots are cautioned to adhere to altitudes as prescribed because, in certain instances, they may be used as the basis for vertical separation of aircraft by ATC. When a depicted altitude is specified in the ATC clearance, that altitude becomes mandatory as defined above. 2. The ILS glide slope is intended to be intercepted at the published glide slope intercept altitude. This point marks the PFAF and is depicted by the ”lightning bolt” symbol 5−4−7 7110.65R CHG 2 AIM AIM on U.S. Government charts. Intercepting the glide slope at this altitude marks the beginning of the final approach segment and ensures required obstacle clearance during descent from the glide slope intercept altitude to the lowest published decision altitude for the approach. Interception and tracking of the glide slope prior to the published glide slope interception altitude does not necessarily ensure that minimum, maximum, and/or mandatory altitudes published for any preceding fixes will be complied with during the descent. If the pilot chooses to track the glide slope prior to the glide slope interception altitude, they remain responsible for complying with published altitudes for any preceding stepdown fixes encountered during the subsequent descent. 3. Approaches used for simultaneous (parallel) independent and simultaneous close parallel operations procedurally require descending on the glideslope from the altitude at which the approach clearance is issued (refer to 5-4-15 and 5-4-16). For simultaneous close parallel (PRM) approaches, the Attention All Users Page (AAUP) may publish a note which indicates that descending on the glideslope/glidepath meets all crossing restrictions. However, if no such note is published, and for simultaneous independent approaches (4300 and greater runway separation) where an AAUP is not published, pilots are cautioned to monitor their descent on the glideslope/path outside of the PFAF to ensure compliance with published crossing restrictions during simultaneous operations. 4. When parallel approach courses are less than 2500 feet apart and reduced in-trail spacing is authorized for simultaneous dependent operations, a chart note will indicate that simultaneous operations require use of vertical guidance and that the pilot should maintain last assigned altitude until established on glide slope. These approaches procedurally require utilization of the ILS glide slope for wake turbulence mitigation. Pilots should not confuse these simultaneous dependent operations with (SOIA) simultaneous close parallel PRM approaches, where PRM appears in the approach title. 5. Altitude restrictions depicted at stepdown fixes within the final approach segment are 5−4−8 3/15/07 5/19/22 6/17/21 applicable only when flying a Non−Precision Approach to a straight−in or circling line of minima identified as a MDA(H). Stepdown fix altitude restrictions within the final approach segment do not apply to pilots using Precision Approach (ILS) or Approach with Vertical Guidance (LPV, LNAV/ VNAV) lines of minima identified as a DA(H), since obstacle clearance on these approaches are based on the aircraft following the applicable vertical guidance. Pilots are responsible for adherence to stepdown fix altitude restrictions when outside the final approach segment (i.e., initial or intermediate segment), regardless of which type of procedure the pilot is flying. (See FIG 5−4−1.) c. The Minimum Safe Altitudes (MSA) is published for emergency use on IAP or departure procedure (DP) graphic charts. MSAs provide 1,000 feet of clearance over all obstacles, but do not necessarily assure acceptable navigation signal coverage. The MSA depiction on the plan view of an approach chart or on a DP graphic chart contains the identifier of the center point of the MSA, the applicable radius of the MSA, a depiction of the sector(s), and the minimum altitudes above mean sea level which provide obstacle clearance. For conventional navigation systems, the MSA is normally based on the primary omnidirectional facility on which the IAP or DP graphic chart is predicated, but may be based on the airport reference point (ARP) if no suitable facility is available. For RNAV approaches or DP graphic charts, the MSA is based on an RNAV waypoint. MSAs normally have a 25 NM radius; however, for

aim bsc w chg 1 2 dtd 5-19-22

Related documents

Add this document to collection(s)

Add this document to saved

Suggest us how to improve StudyLib